Brother DCP-9040CN
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
35000
Скорость печати
A4
20
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Тип устройства |
МФУ |
Размещение |
настольный |
Цветность печати |
цветная |
Область применения |
малый офис |
Число страниц в месяц |
35 000 |
Копир |
|
Сканер |
|
Макс. формат |
A4 |
Факс |
|
Печать фотографий |
|
Телефон |
|
Принтер |
|
Количество цветов |
4 |
Печать без полей |
|
Двусторонняя печать |
|
Прямая печать |
|
Пигментные чернила |
|
Макс, разрешение для ч/б печати |
|
| По Y | 600 |
| По X | 2 400 |
Скорость ч/б печати |
|
| A4 | 20 |
Время выхода первого отпечатка |
|
| Ч/б | 16 |
| Цветн, | 17 |
Копир |
|
Макс, количество копий за цикл |
99 |
Шаг масштабирования |
0,01 |
Время выхода первой копии |
23 |
Значение масштаба |
|
| Максимальное | 4 |
| Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
| По X | 1 200 |
| По Y | 600 |
Сканер |
|
Отправка изображения по e-mail |
|
Глубина цвета |
48 бит |
Емкость устройства автоподачи оригиналов |
35 |
Макс. формат оригинала |
A4 |
Устройство автоподачи оригиналов |
одностороннее |
Стандарт WIA |
|
Стандарт TWAIN |
|
Тип сканера |
планшетный/протяжный |
Оттенки серого |
256 |
Тип датчика сканера |
контактный (CIS) |
Макс, размер сканирования |
|
| По X | 216 |
| По Y | 297 |
Разрешение сканера |
|
| По Х | 1 200 |
| По Y (улучшенное) | 19 200 |
| По Х (улучшенное) | 19 200 |
| По Y | 2 400 |
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
2 500 |
Ресурс цветного картриджа/тонера |
1 500 |
Ресурс фотобарабана |
17 000 |
Печать на: |
|
| CD/DVD |
|
| Рулоне |
|
| Фотобумаге |
|
| Карточках |
|
| Матовой бумаге |
|
| Конвертах |
|
| Глянцевой бумаге |
|
| Этикетках |
|
| Пленках |
|
Плотность бумаги |
|
| Максимальная | 163 |
| Минимальная | 60 |
Факс |
|
Цветной |
|
Телефон |
|
Спикерфон |
|
Проводная трубка |
|
Беспроводная трубка |
|
АОН |
|
Caller ID |
|
Автоответчик |
|
Стандарт DECT |
|
Языки управления |
|
| PCL 5c |
|
| PostScript 2 |
|
| PCL 5e |
|
| PPDS |
|
|
|
|
| PostScript |
|
| PCL 6 |
|
| PostScript 3 |
|
Лотки |
|
Подача бумаги |
|
| Стандартная | 300 |
Вывод бумаги |
|
| Стандартный | 150 |
Финишер |
|
Степлер |
|
Сортер |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Брошюровщик |
|
Интерфейсы |
|
Версия USB |
2,0 |
Wi-Fi |
|
Устройство для чтения карт памяти |
|
RS-232 |
|
Инфракрасный порт |
|
LPT |
|
Bluetooth |
|
FireWire (IEEE 1394) |
|
Веб-интерфейс |
|
USB |
|
Ethernet (RJ-45) |
|
Память/Процессор |
|
Макс, объем памяти |
576 |
Объем памяти |
64 |
Частота процессора |
300 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Экран |
|
Поддержка ОС |
|
| DOS |
|
| Windows |
|
| Mac OS |
|
Потребляемая мощность |
|
| При работе | 495 |
| В режиме ожидания | 95 |
Уровень шума |
|
| В режиме ожидания | 30 |
| При работе | 54,5 |
Габариты |
|
Вес |
32,8 |
Высота |
482 |
Глубина |
487 |
Ширина |
432 |
Модули
ADF
LASER UNIT
PANEL
COVERS and LABELS
FUSER UNIT
COVERS & LABELS
PCB
DRIVE
FRAME UNIT
PERIODICAL MAINTENANCE PART
MP UNIT
PAPER TRAY
DOCUMENT SCANNER
PAPER EJECT
PAPER FEEDER
Детали COVERS
| Деталь: | ADF UNIT(SP) |
| Парткод: | LP7106001 |
| Деталь: | HINGE ASSY L |
| Парткод: | LP2609001 |
| Деталь: | HINGE ARM R, GRAY(1861) |
| Парткод: | LE6244004 |
| Деталь: | ADF EMBLEM, MFC9440CN |
| Парткод: | LP2613001 |
| Деталь: | ADF EMBLEM, DCP9040CN |
| Парткод: | LP2680001 |
| Деталь: | TAPTITE CUP B M3X10 |
| Парткод: | 87311016 |
| Деталь: | DOCUMENT COVER SUB ASSY, GRAY(1861) |
| Парткод: | LP2583001 |
| Деталь: | DRIVE FRAME ASSY |
| Парткод: | LF9080001 |
| Деталь: | ADF SENSOR PCB ASSY |
| Парткод: | LG7146001 |
| Деталь: | EJECTION ROLLER ASSY |
| Парткод: | LF6577001 |
| Цена: | 1 700 ₽ |
| Деталь: | LF ROLLER ASSY |
| Парткод: | LF6579001 |
| Цена: | 1 300 ₽ |
| Деталь: | DOCUMENT HOLD ASSY |
| Парткод: | LP2591001 |
| Деталь: | DOCUMENT SPRING |
| Парткод: | LP2594001 |
| Деталь: | LOWER CHUTE FILM |
| Парткод: | LF6865001 |
| Деталь: | UPPER DOCUMENT CHUTE ASSY, GRAY(1862) |
| Парткод: | LP2595001 |
| Деталь: | SEPARATE ROLLER SHAFT ASSY |
| Парткод: | LP2601001 |
| Цена: | 2 200 ₽ |
| Деталь: | GEAR COVER,GRAY(1682) |
| Парткод: | LP2603001 |
| Деталь: | ADF COVER ASSY, GRAY(1862) |
| Парткод: | LP2604001 |
| Деталь: | ADF SIDE COVER, GRAY(1862) |
| Парткод: | LP2606001 |
| Деталь: | ADF FRONT COVER, GRAY(1862) |
| Парткод: | LP2607001 |
| Деталь: | TAPTITE CUP S M3X6 |
| Парткод: | 87320616 |
| Деталь: | HINGE BASE R, GRAY(1861) |
| Парткод: | LP2588001 |
| Деталь: | DOCUMENT STOPPER, GRAY(1861) |
| Парткод: | LP2589001 |
| Деталь: | ADF MOTOR |
| Парткод: | LF9081001 |
| Деталь: | TAPTITE BIND S M3X6 |
| Парткод: | 85320616 |
| Деталь: | SEPARATION RUBBER |
| Парткод: | LF7135001 |
| Деталь: | LASER UNIT (SP) |
| Парткод: | LR1461001 |
| Деталь: | LASER CAUTION LABEL |
| Парткод: | LJ0908001 |
| Деталь: | TAPTITE CUP S M3X6 SR |
| Парткод: | LM5867001 |
| Деталь: | PANEL UNIT, MFC9440CN US/ CAN/ GER/ UK/ FRA/ BEL / NLD/ CHE/ IRE/ SPA/ ITA/ POR/ CHN/ ZAF/ ASA/ BRA/ ARL/ NZ/ PND |
| Парткод: | LP2614001 |
| Деталь: | PANEL UNIT, DCP9040CN FOR US/ CAN |
| Парткод: | LP2548001 |
| Деталь: | PANEL UNIT, MFC9440CN FOR RUS/ EEU |
| Парткод: | LS0709001 |
| Деталь: | PANEL UNIT, DCP9040CN FOR GER/ UK/ FRA/ BEL/ NLD / CHE/ SPA/ ITA/ POR/ CHN/ ASA/ RUS/ PND/ EEU |
| Парткод: | LP7157001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR US/ CAN |
| Парткод: | LP2616001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR US/ CAN |
| Парткод: | LP2557001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR GER/ CHE/ EEUGERMAN |
| Парткод: | LP7161001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR GER/ CHE/ EEUGERMAN |
| Парткод: | LS0673001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR UK/ IRE/ FRA/ BEL/ NLD/ ZAF/ EEUENGLISH |
| Парткод: | LP7051001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR UK/ FRA/ BEL/ NLD/ ASA/ EEU ENGLISH |
| Парткод: | LP7149001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR FRA/ BEL/ NLD/ CHEFRENCH |
| Парткод: | LP7052001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR FRA/ BEL/ NLD/ CHE FRENCH |
| Парткод: | LP7150001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR FRA/ BEL/ NLDDUTCH |
| Парткод: | LP7053001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR FRA/ BEL/ NLD DUTCH |
| Парткод: | LP7151001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR SPA/ POR SPANISH |
| Парткод: | LP7040001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR SPA/ POR SPANISH |
| Парткод: | LP7141001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR SPA/ POR PORTUGUESE |
| Парткод: | LP7044001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR SPA/ POR PORTUGUESE |
| Парткод: | LP7143001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR ITA |
| Парткод: | LP7047001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR ITA |
| Парткод: | LP7147001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR CHN |
| Парткод: | LS0530001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR CHN |
| Парткод: | LS0524001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR ASA/ ARL/ NZ |
| Парткод: | LP7167001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR BRA |
| Парткод: | LS0526001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR RUS |
| Парткод: | LS0528001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR RUS |
| Парткод: | LS0523001 |
| Деталь: | PRINTED PANEL COVER, MFC9440CN FOR PND |
| Парткод: | LP7173001 |
| Деталь: | PRINTED PANEL COVER, DCP9040CN FOR PND |
| Парткод: | LS0522001 |
| Деталь: | TAPTITE CUP B M3X10 |
| Парткод: | 87311016 |
| Деталь: | PANEL COVER, GRAY(1861), MFC9440CN |
| Парткод: | LP2615001 |
| Деталь: | PANEL COVER, GRAY(1861), DCP9040CN |
| Парткод: | LP2549001 |
| Деталь: | RUBBER KEY R, MFC9440CN |
| Парткод: | LP2550001 |
| Деталь: | RUBBER KEY R, DCP9040CN |
| Парткод: | LP2552001 |
| Деталь: | RUBBER KEY C, MFC9440CN |
| Парткод: | LP2628001 |
| Деталь: | RUBBER KEY C, DCP9040CN |
| Парткод: | LP2690001 |
| Деталь: | RUBBER KEY L, MFC9440CN |
| Парткод: | LP2630001 |
| Деталь: | RUBBER KEY L, DCP9040CN |
| Парткод: | LP2554001 |
| Деталь: | PANEL PCB ASSY, MFC9440CN |
| Парткод: | LG7154001 |
| Деталь: | PANEL PCB ASSY, DCP9040CN |
| Парткод: | LG7245001 |
| Деталь: | LCD, MFC9440CN FOR US/ CAN/ GER/ UK/ FRA/ BEL/ NLD/ CHE/ IRE/ SPA/ ITA/ POR/ CHN/ ZAF/ ASA/ BRA/ ARL/ NZ/ PND, DCP9040CN FOR US/ CAN |
| Парткод: | LG6275001 |
| Деталь: | LCD, MFC9440CN FOR RUS/ EEU, DCP9040CN FOR GER/ UK/ FRA/ BEL/ NLD/ CHE/ SPA/ ITA/ POR/ CHN/ ASA/ RUS/ PND/ EEU |
| Парткод: | LG7451001 |
| Деталь: | BACK LIGHT MODULE |
| Парткод: | LG6257001 |
| Деталь: | PANEL INSULATION SHEET |
| Парткод: | LP7001001 |
| Деталь: | PANEL INSULATION SHEET L, MFC9440CN |
| Парткод: | LP7085001 |
| Деталь: | PANEL INSULATION SHEET L, DCP9040CN |
| Парткод: | LP7087001 |
| Деталь: | ADDRESS LABEL, MFC9440CN |
| Парткод: | LP2621001 |
| Деталь: | PANEL INSULATION SHEET R, MFC9440CN |
| Парткод: | LP7086001 |
| Деталь: | PANEL INSULATION SHEET R, DCP9040CN |
| Парткод: | LP7088001 |
| Деталь: | Винт |
| Парткод: | 087320616 |
| Деталь: | FUSER UNIT 115V(SP) FOR US/ CAN/ BRA |
| Парткод: | LR1962001 |
| Деталь: | FUSER UNIT 230V(SP) FOR GER/ UK/ FRA/ BEL/ NLD/ CHE/ IRE/ SPA/ ITA/ POR/ CHN/ ZAF/ ASA/ RUS/ ARL/ NZ/ PND/ EEU |
| Парткод: | LR1963001 |
| Деталь: | JOINT COVER SUB ASSY, GRAY(1862), MFC9440CN |
| Парткод: | LS0620001 |
| Деталь: | JOINT COVER SUB ASSY, GRAY(1862), DCP9040CN |
| Парткод: | LS0621001 |
| Деталь: | PAPER CHUTE |
| Парткод: | LP2563001 |
| Деталь: | PAPER STOPPER, BLUE(6509) |
| Парткод: | LP2564001 |
| Деталь: | PAPER STOPPER GUIDE, BLUE(6509) |
| Парткод: | LP2565001 |
| Деталь: | STACK LEVER HOLDER L |
| Парткод: | LR1825001 |
| Деталь: | STACK LEVER HOLDER R |
| Парткод: | LR1826001 |
| Деталь: | PAPER STACK LEVER |
| Парткод: | LR1725001 |
| Деталь: | TOP COVER USB FRONT, MFC9440CN |
| Парткод: | LP2819001 |
| Деталь: | TOP COVER USB FRONT, DCP9040CN |
| Парткод: | LP2871001 |
| Деталь: | USB HOST RELAY PCB ASSY, MFC9440CN |
| Парткод: | LM9332001 |
| Деталь: | SPEAKER ASSY |
| Парткод: | LG7270001 |
| Деталь: | SPEAKER HOLDER |
| Парткод: | LP2568001 |
| Деталь: | JOINT SUB COVER, GRAY(1861) |
| Парткод: | LP2570001 |
| Деталь: | DRIVER PCB ASSY |
| Парткод: | LG7149001 |
| Деталь: | PULL ARM L |
| Парткод: | LF6145001 |
| Деталь: | PULL ARM R |
| Парткод: | LF6146001 |
| Деталь: | PULL ARM GUIDE |
| Парткод: | LF6147001 |
| Деталь: | PULL ARM STOPPER |
| Парткод: | LF6148001 |
| Деталь: | PULL ARM SPRING L |
| Парткод: | LS0628001 |
| Деталь: | PULL ARM SPRING R |
| Парткод: | LS0895001 |
| Деталь: | SIDE COVER L ASSY, GRAY(1862) |
| Парткод: | LP2624001 |
| Деталь: | SIDE COVER R ASSY, GRAY(1861) |
| Парткод: | LP2860001 |
| Деталь: | ACCESS COVER |
| Парткод: | LR0516001 |
| Деталь: | BACK COVER ASSY, GRAY(1862) |
| Парткод: | LR1361001 |
| Деталь: | BACK COVER UPPER |
| Парткод: | LR0519001 |
| Деталь: | MJ COVER EXT,MFC9440CN FOR GER/ UK/ FRA/ BEL/ NLD/ IRE/ ITA/ ZAF/ PND |
| Парткод: | UF5745000 |
| Деталь: | CORD HOLDER, GRAY(1861), MFC9440CN |
| Парткод: | LP2612001 |
| Деталь: | TAPTITE BIND B M3X8 |
| Парткод: | 85310816 |
| Деталь: | TAPTITE BIND B M4X12 |
| Парткод: | 85411216 |
| Деталь: | TAPTITE CUP S M4X8 |
| Парткод: | 87420816 |
| Деталь: | TAPTITE CUP S M3X6 |
| Парткод: | 87320616 |
| Деталь: | TAPTITE CUP S M3X8 |
| Парткод: | 87320816 |
| Деталь: | TAPTITE CUP B M3X8 |
| Парткод: | 87310816 |
| Деталь: | TAPTITE CUP B M4X12 |
| Парткод: | 87411216 |
| Деталь: | MAIN PCB ASSY, MFC9440CN FOR US/ CAN |
| Парткод: | LG7167001 |
| Деталь: | MAIN PCB ASSY, MFC9440CN FOR GER/ UK/ FRA/ BEL/ NLD/ CHE/ IRE/ SPA/ ITA/ POR/ CHN/ ZAF/ ASA/ BRA/ RUS/ ARL/ NZ/ PND/ EEU |
| Парткод: | LG7167004 |
| Деталь: | MAIN PCB ASSY, DCP9040CN FOR US/ CAN/ GER/ UK/ FRA/ BEL/ NLD/ CHE/ SPA/ ITA/ POR/ CHN/ ASA/ RUS/ PND/ EEU |
| Парткод: | LG7156001 |
| Деталь: | BATTERY ASSY |
| Парткод: | LG5921001 |
| Деталь: | ENGINE PCB ASSY |
| Парткод: | LM9175001 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR US |
| Парткод: | LG5925001 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR CAN |
| Парткод: | LG5925002 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR GER |
| Парткод: | LG5923054 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR UK/ FRA/ BEL/ NLD/ IRE/ SPA/ ITA/ POR/ RUS/ PND/ EEU |
| Парткод: | LG5923065 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR CHE |
| Парткод: | LG5923056 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR ZAF |
| Парткод: | LG6872001 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR CHN/ ASA |
| Парткод: | LG6190005 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR BRA |
| Парткод: | LG6190006 |
| Деталь: | NCU PCB ASSY, MFC9440CN FOR ARL/ NZ |
| Парткод: | LG6198003 |
| Деталь: | PS PCB UNIT 115V FOR US/ CAN/ BRA |
| Парткод: | LM9246001 |
| Деталь: | PS PCB UNIT AC 230V FOR GER/ UK/ FRA/ BEL/ NLD/ CHE/ IRE/ SPA/ ITA/ POR/ ZAF/ ASA/ ARL/ NZ/ PND/ EEU |
| Парткод: | LM9287001 |
| Деталь: | PS PCB UNIT 230V, MFC9440CN FOR ASA |
| Парткод: | LG7446001 |
| Деталь: | PS PCB UNIT 230V, MFC9440CN FOR CHN/ RUS |
| Парткод: | LG7444001 |
| Деталь: | PS PCB UNIT 230V, DCP9040CN FOR CHN/ RUS |
| Парткод: | LM9503001 |
| Деталь: | CHARGE HVPS PCB ASSY |
| Парткод: | LM9506001 |
| Деталь: | TRANSFER HVPS PCB UNIT |
| Парткод: | LR0902001 |
| Деталь: | TRANSFER HVPS PCB ASSY |
| Парткод: | LM9253001 |
| Деталь: | DENSITY SENSOR |
| Парткод: | LM9224001 |
| Деталь: | REGISTRATION-MARK SENSOR PCB ASSY1 |
| Парткод: | LM9446001 |
| Деталь: | REGISTRATION-MARK SENSOR PCB ASSY2 |
| Парткод: | LM9448001 |
| Деталь: | REGISTRATION RELAY PCB ASSY |
| Парткод: | LM9445001 |
| Деталь: | TAPTITE BIND B M3X8 |
| Парткод: | 85310816 |
| Деталь: | TAPTITE CUP B M3X10 |
| Парткод: | 87311016 |
| Деталь: | DRIVE FRAME UNIT ASSY |
| Парткод: | LR1246001 |
| Деталь: | DRUM DRIVE ASSY |
| Парткод: | LR1904001 |
| Деталь: | DEVELOP DRIVE MOTOR ASSY |
| Парткод: | LR0193001 |
| Деталь: | TAPTITE CUP S M3X6 |
| Парткод: | 87320616 |
| Деталь: | RELEASE RACK |
| Парткод: | LR1006001 |
| Деталь: | RELEASE RACK PLATE |
| Парткод: | LR1007001 |
| Деталь: | TAPTITE CUP B M3X8 |
| Парткод: | 87310816 |
| Деталь: | RELEASE RACK SPRING |
| Парткод: | LR1008001 |
| Деталь: | THM/HUM SENSOR HOLDER ASSY |
| Парткод: | LR1228001 |
| Деталь: | DEVELOP PRESS DRIVE L ASSY |
| Парткод: | LR0803001 |
| Деталь: | DRUM LOCK LEVER L |
| Парткод: | LR1014001 |
| Деталь: | DRUM LOCK LEVER R |
| Парткод: | LR1018001 |
| Деталь: | DRUM LOCK LEVER LABEL |
| Парткод: | LR1710001 |
| Деталь: | DRUM LOCK GEAR 24 |
| Парткод: | LR1023001 |
| Деталь: | HOOK B |
| Парткод: | LR0307001 |
| Деталь: | HOOK C |
| Парткод: | LR0308001 |
| Деталь: | BUSH7 |
| Парткод: | LR0327001 |
| Деталь: | HOOK SPRING BC |
| Парткод: | LR0910001 |
| Деталь: | PP GEAR CLUTCH CAM SPRING |
| Парткод: | LR0310001 |
| Деталь: | BUSH5 |
| Парткод: | LR0296001 |
| Деталь: | PAPER FEED/BELT CLEANER MOTOR ASSY |
| Парткод: | LR0440001 |
| Деталь: | DRUM PHASE SENSOR PCB ASSY1 |
| Парткод: | LM9192001 |
| Деталь: | DRUM PHASE SENSOR PCB ASSY2 |
| Парткод: | LM9337001 |
| Деталь: | DRUM DRIVE MOTOR1 |
| Парткод: | Z31008001 |
| Деталь: | DRUM DRIVE MOTOR2 |
| Парткод: | Z31012001 |
| Деталь: | TAPTITE BIND S M3X6 DEVELOP DRIVE |
| Парткод: | 85320616 |
| Деталь: | DEVELOP RELEASE MOTOR ASSY |
| Парткод: | LR0823001 |
| Деталь: | FRONT COVER INTERLOCK SWITCH ASSY |
| Парткод: | LR0827001 |
| Деталь: | NEW TONER ACTUATOR |
| Парткод: | LR0402001 |
| Деталь: | NEW TONER ACTUATOR SPRING |
| Парткод: | LR0403001 |
| Деталь: | RUBBER FOOT |
| Парткод: | UH2208001 |
| Деталь: | DEVELOP RELEASE SENSOR PCB ASSY |
| Парткод: | LM9189001 |
| Деталь: | TONER LED PCB ASSY |
| Парткод: | LM9210001 |
| Деталь: | LED HOLDER |
| Парткод: | LR1094001 |
| Деталь: | TONER SENSOR PCB ASSY K (TE/NEW) |
| Парткод: | LM9211001 |
| Деталь: | TONER SENSOR PCB ASSY Y (TE/NEW) |
| Парткод: | LM9334001 |
| Деталь: | TONER SENSOR PCB ASSY M (TE/NEW) |
| Парткод: | LM9335001 |
| Деталь: | TONER SENSOR PCB ASSY C (TE/NEW) |
| Парткод: | LM9336001 |
| Деталь: | LED HOLDER |
| Парткод: | UL9037001 |
| Деталь: | BELT CLEANER RELEASE ASSY |
| Парткод: | LR0523001 |
| Деталь: | WASTE TONER SENSOR HOLDER ASSY |
| Парткод: | LR0532001 |
| Деталь: | AIR INTAKE FAN(AIR) |
| Парткод: | LR0589001 |
| Деталь: | BELT UNIT DRIVE MOTOR |
| Парткод: | LR0217001 |
| Деталь: | LVPS FAN (PS) |
| Парткод: | LR0903001 |
| Деталь: | FUSER UNIT FAN (FU) |
| Парткод: | LR0906001 |
| Деталь: | DRUM UNIT FAN (OPC) |
| Парткод: | LR1225001 |
| Деталь: | SCREW PAN (P WASHER) M3X16 |
| Парткод: | 0A2301603 |
| Деталь: | TAPTITE BIND B M3X8 |
| Парткод: | 85310816 |
| Деталь: | TAPTITE CUP B M3X8 |
| Парткод: | 87310816 |
| Деталь: | ALUMINUM SHEET FRAME |
| Парткод: | LR1820001 |
| Деталь: | BELT CLEANER RELEASE SENSOR PCB ASSY |
| Парткод: | LM9218001 |
| Деталь: | WASTE TONER SENSOR |
| Парткод: | LM9221001 |
| Деталь: | FRONT DOOR UNIT ASSY (SP) |
| Парткод: | LR1768001 |
| Деталь: | HINGE SHAFT L |
| Парткод: | LR0860001 |
| Деталь: | HINGE SHAFT R |
| Парткод: | LR0861001 |
| Деталь: | COLLAR 3 |
| Парткод: | LR0862001 |
| Деталь: | BROTHER EMBLEM |
| Парткод: | LR1247001 |
| Деталь: | COLOR LASER LABEL |
| Парткод: | LR1248001 |
| Деталь: | HEATER CAUTION LABEL |
| Парткод: | LR1388001 |
| Деталь: | CAUTION LABEL S 13X40 |
| Парткод: | LU0233001 |
| Деталь: | FRONT DOOR MAIN |
| Парткод: | LR1601001 |
| Деталь: | FRONT DOOR SUB |
| Парткод: | LR0707001 |
| Деталь: | HOOK |
| Парткод: | LR1037001 |
| Деталь: | HOOK SPRING L |
| Парткод: | LR1676001 |
| Деталь: | HOOK SPRING R |
| Парткод: | LR1677001 |
| Деталь: | HOOK SHAFT |
| Парткод: | LR1025001 |
| Деталь: | FRONT COVER RELEASE BUTTON |
| Парткод: | LR0691001 |
| Деталь: | BUTTON SPRING |
| Парткод: | LR0692001 |
| Деталь: | HOOK COVER |
| Парткод: | LR0700001 |
| Деталь: | MP PAPER GUIDE ASSY |
| Парткод: | LR0854001 |
| Деталь: | MP COVER ASSY |
| Парткод: | LR0856001 |
| Деталь: | SEPARATION PAD ASSY MP |
| Парткод: | LR0716001 |
| Деталь: | SEPARATION PAD SPRING MP |
| Парткод: | LR0718001 |
| Деталь: | MP ROLLER HOLDER ASSY |
| Парткод: | LR1916001 |
| Деталь: | MP FEED FRAME COVER |
| Парткод: | LR0853001 |
| Деталь: | PAPER TRAY UNIT |
| Парткод: | LR1186002 |
| Деталь: | SEPARATION PAD ASSY |
| Парткод: | LM5237001 |
| Деталь: | SEPARATION PAD SPRING |
| Парткод: | LR0931001 |
| Деталь: | DOCUMENT SCANNER UNIT(SP) |
| Парткод: | LP7105001 |
| Деталь: | PAPER EJECT ASSY SX (SP) |
| Парткод: | LU0534001 |
Коды ошибок
20
21
22
23
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3D
3F
50
51
52
53
54
55
56
57
58
59
5A
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
71
72
73
74
75
76
78
7C
7D
82
84
85
86
88
89
8A
8B
8C
8E
8F
9B
9D
9E
A2
A3
A5
A6
A7
AD
AE
AF
B0
B2
B3
B4
B5
B6
B9
BB
BD
BE
BF
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0...DF
E6
EF
F8
Описание
| Error code: | 20 |
| Description: | Vertical image or label drift |
| Causes: | The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media. |
| Remedy: | Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation. |
| Error code: | 21 |
| Description: | The bar code printed on a label does not scan. |
| Causes: | The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code. |
| Remedy: | Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label. |
| Error code: | 22 |
| Description: | Loss of printing registration on labels. Excessive vertical drift in top-of-form registration. |
| Causes: | The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly. |
| Remedy: | Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58. |
| Error code: | 23 |
| Description: | Auto Calibrate failed. |
| Causes: | Media or ribbon is loaded incorrectly. The sensors could not detect the media or ribbon. The sensors are dirty or positioned improperly. The sensors are dirty, or media is positioned improperly for the sensors to detect. The media type is set incorrectly. |
| Remedy: | Ensure that media and ribbon are loaded correctly. Manually calibrate the printer. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Ensure that the sensors are clean and that media is positioned properly. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. |
| Error code: | 25 |
| Description: | A label format was sent to the printer. Several labels print, then the printer skips, misplaces, misses, or distorts the image on the label. |
| Causes: | The serial communication settings are incorrect. |
| Remedy: | Ensure that the flow control settings match. Check the communication cable length. See Table 5 on page 48 for requirements. Check the printer driver or software communications settings (if applicable). |
| Error code: | 26 |
| Description: | A label format was sent to the printer but was not recognized. The DATA light flashes but no printing occurs. |
| Causes: | The prefix and delimiter characters set in the printer do not match the ones in the label format. Incorrect data is being sent to the printer. |
| Remedy: | Verify the prefix and delimiter characters. See Set Format Prefix Character on page 94 and Set Delimiter Character on page 95 for the requirements. Check the communication settings on the computer. Ensure that they match the printer settings. If the problem continues, check the label format. |
| Error code: | 27 |
| Description: | Broken or melted ribbon |
| Causes: | Darkness setting too high. |
| Remedy: | 1. Reduce the darkness setting. 2. Clean the printhead thoroughly. |
| Error code: | 28 |
| Description: | The printer does not detect when the ribbon runs out. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
| Causes: | The ribbon-out threshold is set too high to detect the ribbon. On a sensor profile, the ribbon-out threshold (circled in Figure 15) appears above the black bars that indicate the ribbon. This happens if you calibrate the printer without ribbon and later insert ribbon without recalibrating the printer or loading printer defaults. |
| Remedy: | 1. Print a sensor profile (see Print Sensor Profile on page 89), and note the location of the ribbon-out threshold (circled in Figure 15). 2. Calibrate the printer, this time using ribbon, or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. Important • Loading defaults resets all printer parameters back to factory defaults. 3. Print another sensor profile, and compare it to the first one. 4. If the ribbon-out threshold is still too high, you may manually change the value. |
| Error code: | 29 |
| Description: | The ribbon light is on even though ribbon is loaded correctly. |
| Causes: | The printer was not calibrated for the label and ribbon being used. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. |
| Error code: | 2A |
| Display: | No Ink Cartridge |
| Description: | Faulty NVRAM Data |
| Causes: | NVRAM PWB-A (Engine Control Board) |
| Remedy: | 1 Unplug the power cord and plug it in, then turn OFF and ON the Power Switch. 2 Check NVRAM (PJ26) on PWB-A for proper connection and correct as necessary. 3 Change PWB-A. |
| Error code: | 2B |
| Display: | No Ink Cartridge |
| Description: | NVRAM Access Failure |
| Causes: | NVRAM PWB-A (Engine Control Board) |
| Remedy: | 1 Unplug the power cord and plug it in, then turn OFF and ON the Power Switch. 2 Check NVRAM (PJ26) on PWB-A for proper connection and correct as necessary. 3 Change PWB-A. |
| Error code: | 2C |
| Display: | No Ink Cartridge |
| Description: | NVRAM Install Failure |
| Causes: | NVRAM PWB-A (Engine Control Board) |
| Remedy: | 1 Unplug the power cord and plug it in, then turn OFF and ON the Power Switch. 2 Check NVRAM (PJ26) on PWB-A for proper connection and correct as necessary. 3 Change PWB-A. |
| Error code: | 2D |
| Display: | No Ink Cartridge |
| Description: | Scan drive problem or fuse 5 on optics board |
| Causes: | 1 Toner/New sensor PCB failure. 2 Engine PCB failure. 3 High-voltage power supply PCB failure. 4 Main PCB failure |
| Remedy: | <User Check> - Check if an incompatible Ink cartridge is loaded. - Reload the Ink cartridge. - Replace the Ink cartridge. 1 Ink cartridge detection sensor defective Replace the Ink refill ASSY. 2 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 2E |
| Display: | Unable to print 2E |
| Description: | Unable to communicate with the Ink cartridge IC chip. (On the main unit side) |
| Causes: | 1 Toner/New sensor PCB failure. 2 Engine PCB failure. 3 High-voltage power supply PCB failure. 4 Main PCB failure |
| Remedy: | 1 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 2F |
| Display: | Close Ink Cover |
| Description: | The Ink cartridge cover sensor detected an opened cover. |
| Remedy: | <User Check> - Close the Ink cartridge cover. 1 Ink cartridge cover sensor harness connection failure Reconnect the Ink cartridge cover sensor harness. 2 Damaged Ink cartridge cover Replace the Ink cartridge cover. 3 Ink cartridge cover sensor defective Replace the Ink cartridge cover sensor ASSY. 4 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 30 |
| Description: | The LCD displays a language that I cannot read |
| Causes: | The language parameter was changed through the control panel or a firmware command. |
| Remedy: | 1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language. |
| Error code: | 31 |
| Description: | The LCD is missing characters or parts of characters |
| Causes: | The LCD may need replacing. |
| Remedy: | Run the Power-On Self Test on page 117 and check that the LCD display shows all characters. If not, replace the LCD. |
| Error code: | 32 |
| Description: | Changes in parameter settings did not take effect |
| Causes: | Parameters are set incorrectly. A command turned off the ability to change the parameter. A command changed the parameter back to the previous setting. If the problem continues, there may be a problem with the main logic board. |
| Remedy: | 1. Set parameters and save permanently. 2. Turn the printer off (O) and then on (I). Refer to the ZPL Programming Guide. Refer to the ZPL Programming Guide. Replace the main logic board. |
| Error code: | 33 |
| Description: | The printer fails to calibrate or detect the top of the label. |
| Causes: | The printer was not calibrated for the label being used. The printer is configured for continuous media. The driver or software configuration is not set correctly. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81. Driver or software settings produce commands that can overwrite the printer configuration. Check the driver or software media-related setting. |
| Error code: | 34 |
| Description: | Non-continuous labels are being treated as continuous labels. |
| Causes: | The printer was not calibrated for the media being used. The printer is configured for continuous media. |
| Remedy: | Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81. |
| Error code: | 35 |
| Description: | All lights are on, but nothing displays on the LCD, and the printer locks up. |
| Causes: | Internal electronic or firmware failure. |
| Remedy: | Turn the printer power off (O) and then on (I). If the printer locks up again, replace the main logic board. |
| Error code: | 36 |
| Description: | The printer locks up while running the Power-On Self Test. |
| Causes: | Main logic board failure. |
| Remedy: | Replace the main logic board. |
| Error code: | 37 |
| Description: | Non-continuous labels are being treated as continuous labels. |
| Causes: | The printer is configured for continuous media. The printer was not calibrated for the media being used. |
| Remedy: | Set the media type to noncontinuous media. See Set Media Type on page 56. Perform the calibration procedure in Calibrate Media and Ribbon Sensors on page 67. |
| Error code: | 38 |
| Description: | All lights are on, but nothing displays on the LCD, and the printer locks up. |
| Causes: | Internal electronic or firmware failure. |
| Remedy: | Turn the printer power Off (O) and then On (I). If the printer locks up again, replace the main logic board. |
| Error code: | 39 |
| Description: | The printer locks up while running the Power-On Self Test. |
| Causes: | Main logic board failure. |
| Remedy: | Replace the main logic board. |
| Error code: | 3A |
| Description: | Engine PCB transfer error. (Communication error between the main CPU and sub CPU.) |
| Causes: | 1 Harness connection failure between engine PCB and main PCB. 2 Engine PCB failure. 3 Main PCB failure. |
| Remedy: | 1 Harness connection failure between engine PCB and main PCB Check the harness connection between the engine PCB ASSY and main PCB ASSY, and reconnect it. 2 Engine PCB failure Replace the engine PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 3B |
| Display: | Unable to print 3B |
| Description: | Main PCB RAM failure |
| Causes: | Main PCB failure |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | 3D |
| Description: | EEPROM reading error (Not applicable) |
| Error code: | 3F |
| Display: | Unable to print 3F |
| Description: | Carriage motor cannot stop. |
| Causes: | 1 Engine PCB failure. 2 Main PCB failure. |
| Remedy: | <User Check> - Release the release lever at the back of the Paper tray and remove the jammed recording paper from the Engine part. 1 Carriage motor harness connection failure Reconnect the Carriage motor harness. 2 CR encoder strip stained Clean the CR encoder strip. 3 CR encoder strip defective Replace the CR encoder strip. 4 CR encoder sensor defective Replace the Carriage PCB ASSY. 5 Carriage motor defective Replace the Carriage motor ASSY. 6 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 50 |
| Display: | Tray 2 Paper Empty |
| Description: | Fuser Fan Failure The Fuser Fan rotation signal indicates to the Engine Control Board that the fan is no longer operational. |
| Causes: | • Fuser Fan, PL5.3.31 • FAN/PHD/MOT Harness, PL10.1.9 • Engine Control Board, PL9.1.16 |
| Remedy: | 1 Check the Fuser Fan for damage. Remove the Front Cover. Is the fan damaged? Replace the Fuser Fan. Go to Step 2. 2 Check the Fuser Fan connection. Is P/J482 connected to the harness? Go to Step 2. Reconnect the Fan. 3 Check orientation of the Fuser Fan. Does the Fan’s label face into the chute? Go to Step 3. Correct the installation. 4 Test the Fuser Fan. Run the Service Diagnostics Fuser Fan test. Does the Fan operate. Go to Step 6. Go to Step 5. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J482. 2. Check continuity between J48 <=> P483. Go to Step 5. Replace the FAN/PHD/MOT Harness. 6 Check the fan rotation signal. Print one sheet. Is there +3.3 V across P/J48-A12 <=> P/J48-A13? Replace the Engine Control Board. Replace the Fuser Fan. |
| Error code: | 51 |
| Display: | Send Error (DNS) |
| Description: | Rear Fan Failure The Rear Fan rotation signal indicates the fan is no longer operational. |
| Causes: | • Rear Fan, PL1.1.19 • LVPS, PL9.1.6 • Engine Control Board, PL9.1.16 • LV Harness, PL10.1.2 |
| Remedy: | 1 Check the Rear Fan for damage. Remove the Rear Cover. Is the fan damaged? Replace the Rear Fan. Go to Step 2. 2 Check the Rear Fan connection. Is P/J166 connected to the harness? Go to Step 3. Connect the Fan. 3 Check orientation of the Rear Fan. Does the Fan’s label face inwards? Go to Step 4. Correct the installation. 4 Test the Rear Fan. Run the Service Diagnostics Rear Fan test. Does the fan operate? Go to Step 6. Go to Step 5. 5 Check for +24 V to the fan. Disconnect P/J166. Is there +24 V across P166-1 <=> P166-3? Replace the Rear Fan. Replace the LVPS. 6 Check the fan rotation signal to the LVPS. Print one sheet. Is there +3.3 V between P/J166-1 <=> P/J166-3? Replace the Fuser Fan. Go to Step 7. 7 Check the rotation signal from the LVPS. Print one sheet. Is there +3.3 V between P/J165-15 <=> P/J165-3? Replace the LVPS. Go to Step 8. 8 Check the fan rotation signal at the Engine Control Board. Print one sheet. Is there +3.3 V between P/J61-4 <=> P/J61-16? Replace the LV Harness Replace the Engine Control Board. |
| Error code: | 52 |
| Display: | Send Error (POP3) |
| Description: | Fan Failure One of the two fans has failed resulting in a fatal error. |
| Causes: | • Rear Fan, PL1.1.19 • Fuser Fan, PL5.3.31 |
| Remedy: | 1 Check the fans for damage or debris: • Fuser Fan, PL1.1.19 • Rear Fan, PL5.3.31 Is either fan damaged? Replace the defective fan. Go to Step 3. 2 Replace the defective fan. Does the error persist? Go to Step 3 Complete 3 Test the fans. Run the Service Diagnostics fan tests to isolate the defective fan. Did one of the fans fail? Go to the troubleshooting procedure for the specific fan. If both fans pass, replace the Engine Control Board. |
| Error code: | 53 |
| Display: | Send Error (SMTP) |
| Description: | The password did not match in a relay or mailbox transmission, and the transmission ended in failure. |
| Causes: | · Loose cable connection · Defective controller fan · Defective IOD1 board · Defective MCTL board |
| Remedy: | Confirm that both parties are using the same system password and the both units are compatible. Then, ask the remote party to transmit again. |
| Error code: | 54 |
| Display: | Send Error (Wrong Config) |
| Description: | 10-398 ERROR 54 FAN FAILURE |
| Causes: | · Loose cable connection · Defective ozone fan · Defective IOD2 board · Defective MCTL board |
| Remedy: | Enter Service Diagnostics Mode. Run the “Fuser Fan” test. Does the Fuser Fan operate? Y↓N→ Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-1 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-4 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-3 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the Fuser Fan. Replace the Fuser Fan Assembly. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-5 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-8 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-7 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the +24 VDC LVPS Fan. Replace the +24 VDC LVPS Fan. |
| Error code: | 55 |
| Display: | [Stop Pressed] |
| Description: | Stop/Clear has been pressed during a fax transmission. |
| Causes: | · Loose cable connection · Defective fusing unit fan · Defective IOD1 board · Defective MCTL board |
| Remedy: | Try again. |
| Error code: | 56 |
| Display: | Toner Empty |
| Description: | The toner cartridge has run out. The machine stops printing. |
| Causes: | Harness connection failure of back cover switch ASSY. Eject actuator failure. Eject sensor PCB ASSY failure. Main PCB failure |
| Remedy: | Replace the toner cartridge with a new one. |
| Error code: | 57 |
| Display: | Toner Low |
| Description: | The toner cartridge is almost empty. |
| Remedy: | Take out the toner cartridge and thoroughly shake it. By doing this, you can temporarily reestablish printing operations. |
| Error code: | 58 |
| Display: | Tray 1 Paper Empty |
| Description: | There is no paper in the tray 1. |
| Causes: | Harness connection failure between fuser unit and eject sensor PCB. Fuser unit failure. LVPS PCB failure. Eject sensor PCB ASSY failure. Main PCB failure |
| Remedy: | Load paper in the tray 1. |
| Error code: | 59 |
| Display: | Tray 2 Paper Empty |
| Description: | There is no paper in the optional tray 2. |
| Causes: | Harness connection failure between fuser unit and eject sensor PCB. Fuser unit failure. LVPS PCB failure. Eject sensor PCB ASSY failure. Main PCB failure |
| Remedy: | Load paper in the optional tray 2. |
| Error code: | 5A |
| Display: | Unable to print 5A |
| Description: | HVPS PCB failure (Developing bias voltage failure) |
| Causes: | HVPS PCB ASSY harness connection failure. HVPS PCB failure. Main PCB failure |
| Remedy: | 1 HVPS PCB ASSY harness connection failure Check the harness connection between the HVPS PCB and main PCB. Then, reconnect them. 2 HVPS PCB failure Replace the HVPS PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 5E |
| Display: | Unable to print 5E |
| Description: | Overcurrent protection was activated in the driver IC during Maintenance unit pump operation. |
| Causes: | The driving current has exceeded the limit due to an abnormal load applied to the maintenance unit. |
| Remedy: | 1 Foreign materials in the Maintenance unit part Remove foreign materials. 2 Maintenance unit defective Replace the Maintenance unit. 3 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 5F |
| Description: | The waste toner box near full. (The sensor detected that thewaste toner became near full.) |
| Causes: | 1 Harness connection failure of waste toner sensor. 2 Waste toner sensor failure. 3 High-voltage power supply PCB failure. 4 Main PCB failure. |
| Remedy: | 1 Harness connection failure of waste toner sensor Check the harness connection of the waste toner sensor and reconnect it. 2 Waste toner sensor failure Check the sensor performance following the procedure described in “Function code 32”. If any problem occurs, replace the waste toner sensor. 3 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 60 |
| Display: | Nongenuine Toner |
| Description: | Imaging Unit Motor Failure, Code 60 |
| Causes: | • Imaging Unit Drive Motor • Engine Control Board |
| Remedy: | 1 1. Enter service diagnostics and run the Imaging Unit Motor test. 2. Does the motor operate correctly? Go to step 7. Go to step 2. 2 1. Is the voltage at J210-5 +5 VDC? Go to step 3. Replace the engine control board. 3 1. Is the voltage at J210-7 +24 VDC? Go to step 4. Use the +24 VDC wirenets to troubleshoot and resolve the missing voltage. 4 1. Enter service diagnostics. 2. While running the Imaging Unit Motor test, check the voltage at J210-1 and J210-2. 3. Is the voltage 0 VDC while the test is running? Go to step 5. Replace the engine control board. 5 Is the frequency between J210-4 and ground between 1 KHz and 1.3 KHz? Replace the imaging unit drive motor. Go to step 6. 6 1. Check for a short to ground at J210-4. 2. Is the wire grounded? Repair or replace the wiring harness. Replace the engine control board. 7 1. Enter service diagnostics. 2. While running the Imaging Unit Motor test, check the voltage at J210-9. 3. Is the voltage +5 VDC while the test is running? Replace the imaging unit drive motor. Replace the engine control board. |
| Error code: | 61 |
| Display: | Nongenuine Toner Replace Toner 1 |
| Description: | The toner cartridge installed is not a genuine cartridge. |
| Causes: | The printer warms up when the printer is turned on or the cover is closed, or wake from sleep mode. |
| Remedy: | This message appears when you selected stop at the Non Genuine Toner prompt. Install the genuine toner cartridge. |
| Error code: | 62 |
| Display: | Nongenuine Toner Replace Toner |
| Description: | The toner cartridge installed is not a genuine cartridge. |
| Causes: | · Loose cable connection · Defective development clutch for magenta · Defective IOD2 board · Defective MCTL board |
| Remedy: | This message appears when you selected stop at the Non Genuine Toner prompt. Install the genuine toner cartridge. |
| Error code: | 63 |
| Display: | Toner Exhausted |
| Description: | HOST_IF_NO_DRIVER:PCI |
| Causes: | Harness connection failure of new toner sensor harness ASSY. Harness connection failure of toner sensor PCB unit ASSY. New toner sensor harness ASSY failure (Toner empty). Toner sensor PCB unit ASSY failure. Main PCB failure. |
| Remedy: | You can select either stop or continue. It you do not select any, the printer will as stop is selected. If you select stop, you cannot print untill the genuine cartridge is installed. If you select continue, you can keep printing but the guality cannot be guaranteed, and the product svpport is no longer provided. If you wunt to change the selection, turn the printer off and on to gave this message apper again, and then re-select stop or continue. |
| Error code: | 64 |
| Display: | Toner Exhausted Replace Toner 1 |
| Description: | Cover Open |
| Causes: | The Printer Cover is open or Toner Cartridge not installed. |
| Error code: | 65 |
| Display: | Toner Exhausted Replace Toner |
| Description: | The life span of the toner cartridge is reached. |
| Causes: | · Loose cable connection · Defective development solenoid – replace the front cover unit · Defective IOD2 board · Defective MCTL board |
| Remedy: | This message appears when you selected continue at the Toner Exhausted prompt. Install the genuine toner cartridge. |
| Error code: | 66 |
| Display: | TONER SUPPLY LACK |
| Description: | Orange light on The toner supplying error has occurred. |
| Causes: | · Loose cable connection · Defective development solenoid – replace the front cover unit · Defective IOD2 board · Defective MCTL board |
| Remedy: | 1) Check the sealing tape whether it is removed from the toner cartridge and the drum cartridge. (If it is not removed, clean the inside of the set and remove the tape, and then mount it.) 2) Check the harness connected between the Engine controller and the toner motor. (If the harness is out, insert it to the connector.) 3) Check the harness connected between the Engine controller and the toner ID board. (IF the harness is out, insert it to the connector.) 4) Check the harness connected between the Engine controller and the DEVE board. (If the harness is out, insert it to the connector.) 5) In the Engine diagnostic mode, operate the toner motor to check if the motor is operating. (If it is not operating, replace the toner motor.) 6) Check the sensor of the toner empty board whether it is dirty and there are foreign objects. (If it is dirty or there is a foreign object, remove it.) 7) Replace the toner container. 8) Replace the drum cartridge. |
| Error code: | 67 |
| Display: | TOP BIN FULL |
| Description: | Orange light on The top bin is full of papers. Remove papers from the top bin. |
| Causes: | Toner sensor PCB ASSY failure. Main PCB failure |
| Remedy: | 1) Check the harness connected between the Engine controller and the exit board. (If the harness is out, insert it to the connector.) 2) In the Engine diagnostic mode, operate the full_R sensor to check if the sensor is operating. (If it is not operating, replace the exit board.) 3) Check the damage or warping of the sensor actuator. (If it is damaged or warped, replace the top bin full sensor.) 4) Replace the Engine controller. |
| Error code: | 68 |
| Display: | TOP FAN MOTOR LOCK ERROR |
| Description: | Orange light on An error has occurred at the top fan. |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1) Check the harness connected between the Engine controller and the exit board. (If the harness is out, insert it to the connector.) 2) Check the harness connected between the exit board and the top fan. (If the harness is out, insert it to the connector.) 3) In the Engine diagnostic mode, operate the top fan to check the fan is operating. (If it is not operating, replace the top fan.) 4) Check the No. 1 pin of the exit board whether 24V is outputted and check the D5 whether it is normal. (If 24V is not outputted or the part is abnormal, replace the exit board.) 5) Replace the Engine controller. |
| Error code: | 69 |
| Display: | Sleep Mode |
| Description: | Sleep Mode |
| Causes: | It means that the printer fuser is turned off, and the power consumption is minimized. |
| Remedy: | 1) Check the harness connected between the Engine controller and the paper size board. (If the harness is out, insert it to the connector.) 2) In the Engine diagnostic mode, operate the MPF trans sensor to check if it is operating. (If it is not operating, replace the paper size board.) 3) Replace the MPF transfer. |
| Error code: | 6A |
| Description: | Fuser unit failure (The side thermistor does not detect 60°C within the specified time.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6B |
| Description: | Fuser unit failure (The center thermistor does not detect 100°C within the specified time.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6C |
| Display: | Unable to Print 6C |
| Description: | Fuser unit failure (The center thermistor detects higher temperature than the specified value.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6D |
| Description: | Fuser unit failure (The center thermistor detects lower temperature than the specified value.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6E |
| Description: | Fuser unit failure (The center thermistor does not detect temperature rising within the specified time.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6F |
| Display: | Unable to Print 6F |
| Description: | Fuser unit failure (The center and side thermistors detect extremely high temperature.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 71 |
| Display: | Paper Jam 0 |
| Description: | Paper Jam 0 |
| Causes: | The front part of paper is jammed between pickup unit and Feed sensor. |
| Error code: | 72 |
| Display: | Paper Jam 1 |
| Description: | Engine Firmware Failure The Engine Control Board detected a firmware error. |
| Causes: | • Engine Control Board, Pl9.1.16 • EEPROM Board, PL9.1.12 |
| Remedy: | 1 Cycle printer power. Does the error persist? Go to Step 2. Complete 2 Is P/J144 on the EEPROM Board properly seated and defect free? Go to Step 3. Reseat P/J144 or replace the EEPROM Board. 3 Turn printer power off and then back on. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 73 |
| Display: | Paper Jam 2 |
| Description: | Paper Jam 2 |
| Causes: | The front part of paper is jammed just after passing through the discharge sensor. |
| Error code: | 74 |
| Display: | [TRAY x] [PAPER SIZE] EMPTY |
| Description: | F/W Overrun detect |
| Causes: | · Loose cable connection · Defective cleaner clutch · Defective IOD2 board · Defective IOD1 board · Defective MCTL board |
| Remedy: | 1) Check the harness connected between the Engine controller and the TA board. (If the harness is out, insert it to the connector.) 2) Check the harness connected between the TA board and the Pickup unit. (If the harness is out, insert it to the connector.) 3) Check the harness connected between the Pickup unit and the cassette sensing board. (If the harness is out, insert it to the connector.) 4) Check the pickup unit. (If it is inferior part or warped part, replace it.) 5) Check the damage of the cassette sensing B . (If it is damaged, replace the cassette sensing board.) 6) In the Engine diagnostic mode, operate the running count of the paper if it is under 39. (If it is over 39, replace the Pickup unit.) 7) Replace the TA board. |
| Error code: | 75 |
| Display: | [TRAY x] NOT INSTALLED |
| Description: | VIC Limutter |
| Causes: | · Loose cable connection · Defective fusing unit clutch · Defective IOD2 board · Defective MCTL board |
| Remedy: | 1) Check for any warping or damage to the cassette (In the case of warping or damage, replace the cassette) |
| Error code: | 76 |
| Display: | Out Bin Full |
| Description: | Fuser Firmware Failure A failure was detected in the Fuser Firmware. |
| Causes: | • Fuser, PL5.1.1 • FSR/ADC Harness, PL5.2.28 • Engine Control Board, PL9.1.16 |
| Remedy: | 1 Check the Fuser for damage. Is the Fuser damaged? Replace the Fuser. Go to Step 2. 2 Check the Fuser connection for damage. Any broken or bent pins? Repair or replace the parts. Go to Step 3. 3 Replace the Fuser. Does the error persist? Go to Step 4. Complete 4 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J361. 2. Check continuity between J36 <=> J361. Replace the Engine Control Board. Replace the FSR/ ADC Harness. |
| Error code: | 78 |
| Display: | WRONG PAPER SIZE [PAPER] IN [TRAY x] |
| Description: | Waste Cartridge Full Detection Sensor Failure, Code 78 |
| Causes: | • Waste Cartridge • Waste Cartridge Full Sensor • Engine Control Board |
| Remedy: | 1 1. Remove the waste cartridge sensor holder without disconnecting the harnesses. 2. Measure the voltage between the yellow wire on the waste cartridge full sensor and frame ground, alternately interrupting the sensor. 3. Does the voltage toggle between +5 and 0 VDC? Go to step 5. Go to step 2. 2 1. Measure the voltage between the gray wire and frame ground. 2. Does the voltage measure +5 VDC? Go to step 4. Go to step 3. 3 1. Remove the rear cover and rear shield. 2. Measure the voltage at J407B-17 on the engine control board. 3. Does the voltage measure +5 VDC? Inspect the wiring harness for damage and replace, if necessary. Replace the engine control board. 4 1. Measure the voltage between the violet wire and frame ground. 2. Does the voltage measure 0 VDC? Replace the waste cartridge full sensor. Inspect the wiring harness for damage and replace, if necessary. 5 1. Remove the rear cover and rear shield. 2. Measure the voltage at J407B-16 on the engine control board. 3. Alternately interrupt the sensor 4. Does the voltage toggle between +5 and 0 VDC? Replace the engine control board. Inspect the wiring harness for damage and replace, if necessary. |
| Error code: | 7C |
| Description: | Communication error between the engine PCB and main PCB. |
| Causes: | 1 Main PCB failure |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | 7D |
| Display: | Unable to clean 7D |
| Description: | Dirt on drum unit |
| Causes: | Dirt or dust on drum unit electrodes. HVPS PCB failure. Main PCB failure. |
| Remedy: | 1 Dirt or dust on drum unit electrodes Clean the electrodes on the drum unit. ( p.271 "Electrodes location on the drum unit") 2 HVPS PCB failure Replace the HVPS PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 82 |
| Display: | h`******** |
| Description: | Engine Logic Board RAM/ROM Failure, Code 82 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace the engine control board. |
| Error code: | 84 |
| Display: | h`******** |
| Description: | Controller to Engine Logic Board Time Failure, Code 84 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace the engine control board. |
| Error code: | 85 |
| Display: | ROM HASH |
| Description: | Engine Logic Board Micro Pitch Failure, Code 85 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace in the following order: • engine control board • image processor board |
| Error code: | 86 |
| Description: | High-Voltage Power Supply Failure, Code 86 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace in the following order: • T3 HVPS • image processor board |
| Error code: | 88 |
| Display: | Paper Jam |
| Description: | Lower Tray Communication Failure, Code 88 |
| Causes: | • Engine Control Interface Board • Tray module board • Engine Control board |
| Remedy: | 1 Is J668-1 on the tray module board +5 VDC? Go to step 2. Use the wirenets to troubleshoot and repair the open wire. 2 Is J668-3 on the tray module board +24 VDC? Go to step 3. Use the wirenets to troubleshoot and repair the open wire. 3 1. Check the following connectors for continuity: • P669-1 to J534A-15 • P669-2 to J534A-14 • P669-3 to J534A-13 • P669-4 to J534A-12 • P669-5 to J534A-11 • P669-6 to J534A-10 2. Do all checks indicate continuity? Replace in the following order: • engine control interface board • tray module board • engine control board Check and repair broken wires or bad connectors. |
| Error code: | 89 |
| Display: | 89 |
| Description: | ITU Maintenance |
| Causes: | Registration rear sensor failure. Main PCB failure |
| Remedy: | Check the ITU Release Lever for correct operation. The ITU Release Lever is the black lever located on the left upper side frame above the ITU opening and can be seen by opening and lowering the MPF Assembly. When locked the lever should be at the 6 o`clock position. When unlocked it should be in a 3 o`clock position. Undue pressure is not required to operate the lever Turn the printer off, insert the ITU, move the lever to the 6 o`clock position, and turn the printer back on. If this does not resolve, replace the “ITU assembly”. Press Go to continue. The message persists until replacement. |
| Error code: | 8A |
| Display: | Paper Jam |
| Description: | Paper jam in Tray 1 (T1) (It is detects by the registration front sensor) |
| Causes: | Harness connection failure of registration front sensor PCB ASSY. Paper feed roller worn out. Registration front sensor PCB failure. Main PCB failure. |
| Remedy: | 1 Harness connection failure of registration front sensor PCB ASSY Check the harness connection of the registration front sensor PCB ASSY in the appropriate tray, and reconnect it. 2 Paper feed roller worn out Replace the paper feed roller. 3 Registration front sensor PCB failure Check the sensor performance following the procedure ( p.183 "Operational Check of Sensors (Function code 32)"). If any problem occurs, replace the registration front sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8B |
| Display: | Unable to Print 8B |
| Description: | Paper jam in Tray 2 |
| Causes: | Dirt on edge sensor. Harness connection failure of high voltage power supply PCB ASSY. Paper feeding kit worn out (MP/ Tray 1/ Tray 2). Registration front sensor failure. Main PCB failure |
| Remedy: | Clean the edge sensor. Check the harness connection of the high voltage power supply PCB ASSY in the appropriate tray, and reconnect it. Replace the paper feeding kit of the appropriate tray. Procedure described in "4.10 Sensor Operational Check (Function code 32)" in Chapter 6. If any problem occurs, replace the high voltage power supply PCB ASSY. Replace the main PCB ASSY. |
| Error code: | 8C |
| Display: | Paper Jam |
| Description: | Paper jam in MP Tray |
| Causes: | Dirt on edge sensor. Harness connection failure of high voltage power supply PCB ASSY. Paper feeding kit worn out (MP/ Tray 1/ Tray 2). Registration front sensor failure. Main PCB failure |
| Remedy: | Clean the edge sensor. Check the harness connection of the high voltage power supply PCB ASSY in the appropriate tray, and reconnect it. Replace the paper feeding kit of the appropriate tray. Procedure described in "4.10 Sensor Operational Check (Function code 32)" in Chapter 6. If any problem occurs, replace the high voltage power supply PCB ASSY. Replace the main PCB ASSY. |
| Error code: | 8E |
| Description: | Error in the adjustment of inter-color position alignment result when implementing it. |
| Causes: | 1 Harness connection failure of the registration mark L PCB ASSY or registration mark R PCB ASSY. 2 Registration mark sensor holder ASSY failure. 3 Main PCB failure. |
| Remedy: | 1 Harness connection failure of the registration mark L PCB ASSY or registration mark R PCB ASSY Check the harness connection of the registration mark sensor holder ASSY and reconnect it. 2 Registration mark sensor holder ASSY failure Replace the registration mark sensor holder ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8F |
| Display: | Unable to print 8F |
| Description: | Paper feed motor does not stop. The PF encoder sensor cannot detect the rotation of the Paper feed motor. |
| Remedy: | <User Check> - Release the release lever at the back of the Paper tray and remove the jammed recording paper in Jam clear cover part, Platen part and front part. 1 Foreign materials in the recording paper feeding path Remove foreign materials. 2 Paper feed motor harness connection failure Reconnect the Paper feed motor harness. 3 PF encoder sensor harness connection defective Reconnect the PF encoder sensor harness. 4 PF encoder disk defective Replace the PF encoder disk. 5 PF encoder sensor defective Replace the PF encoder sensor PCB ASSY. 6 Paper feed motor defective Replace the Paper feed motor. 7 Main PCB defective Replace the Main PCB ASSY. |
| Error code: | 9B |
| Description: | Request on developing bias voltage adjustment |
| Error code: | 9D |
| Description: | Detection of incorrect registration sensor measurement value when implementing adjustment of inter-color position alignment. |
| Causes: | 1 Foreign object is affixed around the density sensor. 2 Harness connection failure of registration mark sensor holder ASSY. 3 Registration mark sensor PCB failure. 4 High-voltage power supply PCB failure. 5 Engine PCB failure. 6 Low-voltage power supply PCB failure. 7 Main PCB failure. |
| Remedy: | 1 Foreign object is affixed around the density sensor Remove the foreign object affixed around the density sensor. 2 Harness connection failure of registration mark sensor holder ASSY Check the harness connection of the registration mark sensor holder ASSY and reconnect it. 3 Registration mark sensor PCB failure Replace the registration mark sensor holder ASSY. 4 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 5 Engine PCB failure Replace the engine PCB ASSY. 6 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 7 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9E |
| Description: | Toner of the color which is being used reaches the end of life when implementing adjustment of inter-color position alignment. |
| Causes: | 1 Toner/New sensor PCB failure (Toner empty). 2 Engine PCB failure |
| Remedy: | 1 Toner/New sensor PCB failure (Toner empty) Check the sensor performance following the procedure described in “Function code 32”. If any problem occurs, replace the Toner/New sensor PCB ASSY. 2 Engine PCB failure Replace the engine PCB ASSY. |
| Error code: | A2 |
| Display: | DOCUMENT JAM |
| Description: | Jam at Door A |
| Causes: | • Duplex Unit, PL16.1.0 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Door A • Door D • Duplex Unit Rollers • Duplex Unit connector • Duplex Sensors and Actuators Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Duplex Unit sensors. Run the Service Diagnostics for each of the four Duplex Unit sensors. Do the sensors and actuators function correctly Go to Step 3. Replace the damaged sensor. 3 Test the Duplex Unit motors. Run the Service Diagnostics Duplex Motor tests. Do the motors function correctly Go to Step 4. Replace the Duplex Unit 4 Inspect the wiring harness for the Duplex Unit. Is the wiring harness properly connected and free from defects? Replace the Duplex Unit. Replace the Engine Control Board. |
| Error code: | A3 |
| Display: | DOCUMENT JAM |
| Description: | Jam at Door A Misfeed at Tray 1 (MPT) Media reached the Duplex Reverse Sensor, but a second sheet was detected entering the feed path from Tray 1 (MPT). This error represents a misfeed jam for media fed from Tray 1 (MPT). |
| Causes: | • Tray 1 (MPT) Feed Roller, PL10.1.53 • Tray 1 (MPT) Pick Roller, PL10.1.43 • Tray 2 Registration Motor, PL4.2.36 • Tray 2 Feed Motor, PL4.2.35 • Front Sensor Board, PL4.2.97 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Tray 1 (MPT) Feed Rollers • Registration Rollers • Sensor Actuator Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Registration #1 Sensor. Run the Service Diagnostics Registration Entrance Sensor test. Does the sensor operate correctly? Go to Step 3. Replace the actuator. If the error persists, replace the Front Sensor Board. 3 Test the Feed Motor, Registration Motor, and Registration Clutch #1. Do the components function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check each motor and clutch harness. Are the harnesses properly connected and free from defects? Replace the Engine Control Board. Replace the harness and/or problem motor/ clutch. |
| Error code: | A5 |
| Display: | Unable to Scan A5 |
| Description: | ADF interlock |
| Causes: | Scanning failure. |
| Remedy: | 1 Scanning failure Turn the power switch off and on. Then, try scanning again. |
| Error code: | A6 |
| Display: | A6-Bypass Feeder Jam |
| Description: | Paper did not exit the Multi-sheet Bypass Feeder properly, causing a paper jam. Open Cover A and refer to the labels on the printer to clear the jam. |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the feeder. Also ensure the paper is loaded correctly in the feeder. 2. Clean the bypass feeder’s pick roller. 3. Test the main feed motor as described in “Motor and clutch tests”. Replace the main feed motor. 5. Replace the engine controller board. |
| Error code: | A7 |
| Display: | A7-Duplex Entry Jam |
| Description: | Paper did not enter the duplex module properly, causing a paper jam. Open Cover A and refer to the labels on the printer to clear the jam. |
| Causes: | Power supply fan error |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the currently used tray. Also ensure the paper is loaded correctly in the tray. 2. Clean the duplex unit’s rollers. 3. Test the duplex motor and clutch as described in “Motor and clutch tests”. Replace the duplex unit. 5. Replace the engine controller board. |
| Error code: | AD |
| Description: | DMA transfer error |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY |
| Error code: | AE |
| Description: | IT home is not detected within 0.7 sec. during rotation of main motor. |
| Causes: | Position error of the intermediate transfer unit |
| Remedy: | Reconnect the home position sensor harness. Replace the drive PCB. Replace the belt. Replace the home position sensor. Replace the scanner motor. Replace the CCD module. Replace the main PCB ASSY. |
| Error code: | AF |
| Display: | Unable to Scan AF |
| Description: | FB unit home position failure |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | B0 |
| Description: | DIS (GI) could not detected. |
| Causes: | Scanner harness not connected correctly. Scanner harness broken. Main PCB failure |
| Remedy: | This may happen in some cases of bad line condition. Attempt the transmission again. |
| Error code: | B2 |
| Description: | DCN is received. |
| Causes: | • Defective gate array U204 on the engine board (KP-864). • Defective harness (S02400) between engine board and option unit interface connector. • Defective paper feeder PF-60. |
| Remedy: | This may happen in some cases of bad line condition. Attempt the transmission again. |
| Error code: | B3 |
| Description: | DCS/DTC was not detected. |
| Causes: | • Defective gate array U204 on the engine board (KP-864). • Defective harness (S02400) between engine board and option unit interface connector. • Defective option paper feeder PF-60. |
| Remedy: | This may happen in some cases of bad line condition. Attempt the transmission again. |
| Error code: | B4 |
| Description: | The sender performed fall-back but the transmission was not enabled. The receiver performed time-out after sending FTT. Or DCN is received. |
| Causes: | • Defective gate array U204 on the engine board (KP-864). • Defective harness (S02400) between engine board and option unit interface connector. • Defective paper feeder PF-60. |
| Remedy: | This may happen in some cases of bad line condition. Attempt the transmission again. Or ask the remote party to attempt the transmission again. |
| Error code: | B5 |
| Description: | CFR (FTT) was not detected. |
| Causes: | 1 Main PCB failure |
| Remedy: | This may happen in some cases of bad line condition. Attempt the transmission again. |
| Error code: | B6 |
| Description: | Stapler drive motor |
| Causes: | 1 Main PCB failure |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | B9 |
| Description: | Scanning light adjustment error is detected. |
| Causes: | FB unit failure. Main PCB failure |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BB |
| Description: | White level data error |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BD |
| Display: | Unable to Scan BD |
| Description: | Engine EEPROM check error. Printing is continued. |
| Causes: | Engine EEPROM check error |
| Remedy: | Replace the CCD module. Replace the main PCB ASSY. |
| Error code: | BE |
| Description: | EEPROM (Imaging unit) check error |
| Causes: | EEPROM (Imaging unit) Errororor |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | BF |
| Display: | Unable to Scan BF |
| Description: | EEPROM (Fuser unit) check error |
| Causes: | EEPROM (Fuser unit) Error error |
| Remedy: | Correct smooth operation and that there is no catching of the document front actuator 2. Replace the document front sensor 2. |
| Error code: | C0 |
| Description: | Image signal carrier was not detected. |
| Causes: | • Defective gate array U204 on the engine board (KP-864). • Blown-out fuse (F202) on the engine board. • Improper installation between printer and option paper feeder. • Defective harness (S02400) between engine board and option unit interface connector. • Improper connector insertion. • Defective option paper feeder PF-60. |
| Remedy: | This may happen in some cases of bad line condition. Ask the remote party to transmit again. |
| Error code: | C1 |
| Description: | PF jam cass. 1 |
| Causes: | • If the actuator of the Separation base unit safety switch is not depressed. |
| Remedy: | This may happen in some cases of bad line condition. Ask the remote party to transmit again. |
| Error code: | C2 |
| Description: | PF jam cass. 2 |
| Causes: | • If the actuator of the Master making unit safety switch is not depressed. |
| Remedy: | This may happen in some cases of bad line condition. Ask the remote party to transmit again. |
| Error code: | C3 |
| Display: | SVC C3 ERROR |
| Description: | PF jam cass.3 |
| Causes: | • If the actuator of the Master removal unit safety switch is not depressed. |
| Remedy: | This may happen in some cases of bad line condition. Ask the remote party to transmit again. |
| Error code: | C4 |
| Display: | SVC C4 ERROR |
| Description: | Machine has reset |
| Causes: | • If the master disposal box set sensor does not detect. |
| Remedy: | This may happen in some cases of bad line condition. Ask the remote party to transmit again. |
| Error code: | C5 |
| Display: | C5:ILLEGAL SIZE |
| Description: | Optics locked or not initialized. Could be scan or lens/mirror |
| Causes: | • If the Ink bottle set sensor does not detect the Ink bottle. |
| Remedy: | Set the Ink bottle in the Drum. |
| Error code: | C6 |
| Description: | Scan problem |
| Causes: | • If the black tape attached at the end of the Master roll has been detected by the Master end sensor during master making or confidential operation. |
| Remedy: | Master making unit safety SW OFF & ON. • Replace the depleted Master roll with a new one. |
| Error code: | C7 |
| Display: | SVC C7 ERROR |
| Description: | Error C7 |
| Causes: | • If the Master removal 5 times. |
| Remedy: | 1. Check if any thermistor connector is disconnected. 2. Check if any harness of the thermistors (center/rear, upper/lower) is open-circuited. 3. Check the LGC board if the connector J122 is disconnected. 4. After completing the repair of what caused the [C7] problem, proceed to rewrite the status counter (08-700) to "0", following the same procedure as for [C41] to [C48] . |
| Error code: | C8 |
| Description: | Paper stays in tray or duplex or HCF |
| Causes: | • If the Ink sensor does not detect ink in the Squeegee unit within 20 seconds after the Inking motor was activated. • If the Ink sensor does not detect ink in the Squeegee unit within 40 seconds after the Inking motor was activated when the Ink bottle is installed just after replacing empty ink bottle. |
| Remedy: | Ink bottle set sensor OFF & 5 seconds later ON. |
| Error code: | C9 |
| Description: | Bypass jam |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | CA |
| Description: | Main board problem |
| Remedy: | Check the harness connection of the USB host relay PCB ASSY and reconnect it. Replace the USB host relay PCB ASSY. Replace the main PCB ASSY. |
| Error code: | CB |
| Description: | ADF drive problem |
| Remedy: | 1 Harness connection failure of registration mark sensor holder ASSY Check the harness connection of the registration mark sensor holder ASSY and reconnect it. 2 Density sensor failure Replace the registration mark sensor holder ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | CC |
| Description: | ADF drive problem |
| Causes: | When SIM1-2 is executed, the sensor’s light receiving level for each document size does not agree with the setting. |
| Remedy: | Clear the trouble by turning the power supply On/Off. Check document detection lighting section height. |
| Error code: | CD |
| Description: | BC RAM hardware |
| Causes: | The CD error also suggests that the sorter ST-30 is defective. |
| Remedy: | Clean both electrodes. Replace the HVPS PCB unit. Replace the main PCB ASSY. |
| Error code: | CE |
| Description: | BC RAM software |
| Causes: | • Defective harness (S02400) between engine board and option unit interface connector. • Defective option bulk paper feeder. |
| Remedy: | 1 Waste toner sensor failure Check the sensor performance following the procedure described in “Function code 32”. If any problem occurs, replace the waste toner sensor. 2 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | CF |
| Description: | Auto toner adjustment did not take |
| Causes: | • Defective harness (S02400) between engine board and option unit interface connector. • Defective option bulk paper stacker HS-8E. |
| Remedy: | If this error occurs again even after the power switch is turned off and then on again, replace the main board (KP-5191) and check for correct operation. |
| Error code: | D0...DF |
| Description: | Modem error |
| Causes: | 1 Main PCB failure |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | E6 |
| Display: | SVC E6 ERROR |
| Description: | Right side interlock |
| Causes: | • If Position-A sensor cannot be detected (or keeps detecting) even though the Main motor encoder sensor signal is making the output after the Main motor is activated. |
| Remedy: | Confirm details of the error using the error code and correct the error. Then ask the remote party to transmit again. |
| Error code: | EF |
| Display: | EF-Fuser Unit Missing |
| Description: | The fuser is either missing or requires reseating to be recognized by the printer. Turn off the printer, make sure the fuser is properly installed and turn on the printer. If the problem persists, install a new fuser. |
| Causes: | LVPS PCB failure. Main PCB failure |
| Remedy: | 1. Remove and reinstall the fuser. 2. install a new fuser. 3. Replace the low-voltage power supply. 4. Replace the engine controller board. |
| Error code: | F8 |
| Display: | Unable to Print F8 |
| Description: | No power to collator |
| Causes: | Battery harness connection failure. Battery exhausted. Main PCB failure. |
| Remedy: | 1 Battery harness connection failure Reconnect the battery harness. 2 Battery exhausted Replace the battery. 3 Main PCB failure Replace the main PCB ASSY. |
Парткод
Название
Brother Ремень переноса изображения
Brother Блок фотобарабана
Brother Узел термозакрепления в сборе 230V
Brother Тонер-картридж черный
Brother Тонер-картридж голубой
Brother Тонер-картридж пурпурный
Brother Тонер-картридж желтый
Brother Тонер-картридж черный
Brother Тонер-картридж голубой
Brother Тонер-картридж пурпурный
Brother Тонер-картридж желтый
Brother Контейнер для отработанного тонера
