Canon imageRUNNER 3225

Общие характеристики
Тип	лазерный/светодиодный
Технология печати	лазерная
Размещение	напольный
Цветность печати
Макс. формат	A3
Печать фотографий
Факс
Телефон
Тип устройства	МФУ
Копир
Сканер
Пигментные чернила
Система непрерывной подачи чернил
Прямая печать
Печать без полей
Время разогрева	35
Двусторонняя печать
Макс, разрешение для ч/б печати
По Y	1 200
По X	1 200
Скорость ч/б печати
A4	25
Макс, количество копий за цикл	999
Время выхода первой копии	4,9
Макс, разрешение (ч/б)
По X	1 200
По Y	600
Скорость ч/б копирования
A3	14
Глубина цвета	24 бит
Оттенки серого	256
Емкость устройства автоподачи оригиналов	50
Тип сканера	планшетный/протяжный
Отправка изображения по e-mail
Стандарт TWAIN
Устройство автоподачи оригиналов	двустороннее
Макс. формат оригинала	A3
Стандарт WIA
Разрешение сканера
По Х	600
Количество картриджей	1
Печать на:
CD/DVD
Фотобумаге
Рулоне
Пленках
Этикетках
Карточках
Конвертах
Матовой бумаге
Глянцевой бумаге
Плотность бумаги
Минимальная	64
Максимальная	128
Цветной
PC Fax
Беспроводная трубка
Проводная трубка
АОН
Caller ID
Автоответчик
Стандарт DECT
Спикерфон
Языки управления
PDF
PPDS
PCL 5c
PostScript 3
PostScript 2
PostScript
PCL 5e
PCL 6
Количество установленных шрифтов
PCL	81
Емкость лотка ручной подачи	50
Подача бумаги
Максимальная	4 950
Стандартная	1 150
Вывод бумаги
Стандартный	1 000
Максимальный	1 600
Сортировка со сдвигом
Брошюровщик
Степлер
Электронная сортировка
Сортер
FireWire (IEEE 1394)
Ethernet (RJ-45)
Устройство для чтения карт памяти
Веб-интерфейс
RS-232
Инфракрасный порт
AirPrint
LPT
Bluetooth
Wi-Fi 802.11n
Wi-Fi
USB
Версия USB	2,0
Макс, объем памяти	1 280
Частота процессора	800
Объем памяти	768
Процессор	Canon
Емкость жесткого диска	60
Экран
Работа от аккумулятора
Поддержка ОС
DOS
Linux
Mac OS
Windows
Потребляемая мощность
При работе	1 350
В режиме ожидания	1,5
Вес	74
Ширина	565
Высота	761
Глубина	700

Error code:	E000-0001
Description:	Fixing fault
Causes:	After the fixing heater has gone on, the reading of the main thermistor is not 50 deg C within about 1.5 sec. Cause The fixing film unit is faulty. The engine controller PCB is faulty.
Remedy:	- Replace the fixing film unit. - Replace the engine controller PCB.

Error code:	E001-0000
Description:	Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control
Causes:	The main thermistor detected a temperature of higher than 255 degree C.
Remedy:	- Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB.

Error code:	E001-0001
Description:	Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control.
Causes:	The sub thermistor detected a temperature of higher than 290 degree C.
Remedy:	- Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB.

Error code:	E001-0002
Description:	Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 1 has detected a high temperature (ASIC detection)
Causes:	The fixing film unit is faulty (i.e., the thermistor has a short circuit). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service move: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR.

Error code:	E002-0000
Description:	Low temperature during temperature control. The target temperature is not reached during temperature control.
Causes:	The fixing film unit is faulty (i.e., the main thermistor TH1 has poor contact, or the fixing heater is faulty). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>FCLEAR>ERR.
Remedy:	- Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB.

Error code:	E003-0000
Description:	Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation.
Causes:	The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater.
Remedy:	- Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB.

Error code:	E004-0000
Description:	Fixing power supply drive circuit error
Causes:	43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started.
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly.

Error code:	E007-0000
Description:	Fixing film sensor failure The fixing film sensor is faulty.
Causes:	The fixing film sensor (PS45) is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR
Remedy:	- Check the connector of the fixing film sensor. - Replace the fixing film sensor. - Replace the DC controller PCB.

Error code:	E010-0001
Description:	Main motor error Lock of the motor fails to be detected 2 sec or more after the motor starts to operate.
Causes:	The main motor drive system has an excess load. The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check on connection of the connector, Replace the motor

Error code:	E010-0002
Description:	Main motor error After rotation of the motor becomes stable, the motor lock fails (i.e., the motor becomes unstable) for 500msec or more.
Causes:	The main motor drive system has an excess load. The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check on connection of the connector, Replace the motor

Error code:	E014-0001
Description:	Fixing motor failure
Causes:	Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached.
Remedy:	Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor.

Error code:	E014-0002
Description:	Fixing motor error When the lock was disengaged after the motor was locked
Causes:	The belt motor (M15) is faulty. The belt motor drive system has an excess load. The drum drive AC generation PCB is faulty. The transfer drive AC generation PCB is faulty. The DC controller PCB is faulty.
Remedy:	Replace the drumITB moter. Replace the fixing moter.Replace the DCDC converterAi38VAj. Replace the fixing belt unit.

Error code:	E019-0000
Description:	Waste toner full detection The waste toner full state was detected.
Causes:	The waste toner case is full. The waste toner case full detection mechanism is soiled. The waste toner sensor is faulty. The DC controller PCB is faulty. Caution To clear the error, dispose of the waste toner, and turn off and then on the main power switch.
Remedy:	Replace the drum unit.

Error code:	E020-0000
Description:	Density sensor failure warning

Error code:	E024-0000
Description:	Toner level sensor failure
Causes:	Failure output from the toner level sensor (Yellow). Cause Memory controller PCB assembly fault, DC controller PCB assembly fault, toner cartridge fault.
Remedy:	- Replace toner cartridge - Replace memory controller PCB - Replace DC controller PCB

Error code:	E024-0001
Description:	Toner level sensor failure
Causes:	Failure output from the toner level sensor (Magenta). Cause Memory controller PCB assembly fault, DC controller PCB assembly fault, toner cartridge fault.
Remedy:	- Replace toner cartridge - Replace memory controller PCB - Replace DC controller PCB

Error code:	E025-0000
Description:	Error in the toner motor Indicates an error of Y developing assembly toner supply
Remedy:	Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor

Error code:	E025-0001
Description:	There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). There is an overcurrent in the hopper stirring motor (M23).
Remedy:	Turn off and then on the main power.

Error code:	E032-0001
Description:	NE controller counter operation failure When the counter function of the NE controller does not work
Causes:	The DA unit is faulty. The main controller PCB is faulty.
Remedy:	Check the cable connections.

Error code:	E064-0001
Description:	The voltage of the power supply is faulty (high-voltage error). The value read from the EEPORM is outside a specific range.
Remedy:	Turn off and then back on the main power. Replace the EEPROM.

Error code:	E064-0002
Description:	The voltage of the power supply is faulty (high-voltage error). While output is being generated, the AD value of the primary DC voltage is 230 (DEC) or more for 100 msec 2 times in sequence. (However, after output, it is not detected for 100 msec.)
Remedy:	Replace the high-voltage power supply. Replace the DC controller PCB.

Error code:	E064-0003
Description:	The voltage of the power supply is faulty (high-voltage error). While output is being generated, the AD value of the developing DC voltage is 224 (DEC) or more for 10 msec 2 times in sequence. (However, after output, it is not detected for 100 msec.)
Remedy:	Replace the high-voltage power supply. Replace the DC controller PCB.

Error code:	E064-0004
Description:	The voltage of the power supply is faulty (high-voltage error). While output is being generated, the AD value of the transfer output current is 205 (DEC) or more for 100 msec 2 times in sequence. (However, after output, it is not detected for 100 msec.)
Remedy:	Replace the high-voltage power supply. Replace the controller PCB.

Error code:	E064-0005
Description:	The voltage of the power supply is faulty (high-voltage error). While output is being generated, the AD value of the transfer output voltage is 0 (DEC) for 100 msec 2 times in sequence. (However, after output, it is not detected for 100 msec.)
Remedy:	Replace the high-voltage power supply. Replace the DC controller PCB.

Error code:	E110-0001
Description:	Optical assembly error (Scanner motor)
Causes:	Optical assembly error (Scanner motor rotation failure)
Remedy:	Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit.

Error code:	E110-0002
Description:	Error in first artificial BD adjustment
Causes:	Primary pseudo BD correction

Error code:	E110-0003
Description:	There is a scanner motor error. The FG signal is not detected while the polygon scanner is rotating stably.
Remedy:	Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power.

Error code:	E191-0000
Description:	There is an error in the communication with the high-voltage power supply The data transmission/reception does not end normally 500 msec after the most recent transmission/reception of data ended normally.
Remedy:	Replace the high-voltage power supply. Replace the DC controller PCB.

Error code:	E197-0000
Description:	Printer engine communication error Erroneous communication between the DC controller PCB and image processor PCB was detected.
Causes:	Internal communication error
Remedy:	- Check the connectors of the DC controller PCB and image processor PCB. - Replace the DC controller PCB for normal connection. - Replace the image processor PCB.

Error code:	E197-0001
Description:	Engine communication error
Causes:	Error between DC controller PCB and main controller PCB. Cause Failure in connection between PCB, failure in DC controller PCB, failure in controller PCB.
Remedy:	- Check the connection of the connector of the DC controller PCB and controller PCB - Replace the DC controller PCB - Replace the controller PCB

Error code:	E197-0003
Description:	There is an error in the communication with the fixing feed PCB. Following the end of initialization of the communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously.
Remedy:	Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power.

Error code:	E202-0001
Description:	Reader HP sensor fault
Causes:	Reader HP outward fault The CCD unit moves backward, but does not move to the home position.
Remedy:	- Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit.

Error code:	E202-0002
Description:	Contact Sensor HP error, Failure in return
Causes:	Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position.
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board.

Error code:	E225
Description:	CIS lamp has a fault.
Remedy:	- Turn the power OFF and then back ON. - Replase the CIS unit.

Error code:	E227-0001
Description:	Reader unit power supply error When the 24 V port is OFF when the power is turned ON.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0002
Description:	Reader unit power supply error When the 24 V port is OFF when a job is started.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0003
Description:	Reader unit power supply error When the 24 V port is OFF when a job is finished.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0004
Description:	Reader unit power supply error When the 24 V port is OFF during load drive.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E248-0001
Description:	EEPROM access error
Causes:	Error at EEPROM power-on EEPROM data cannot be read at power-on.
Remedy:	Replace reader unit.

Error code:	E248-0002
Description:	EEPROM access error
Causes:	Error in EEPROM writing EEPROM writing cannot be performed.
Remedy:	Replace reader unit.

Error code:	E248-0003
Description:	EEPROM access error
Causes:	Error in EEPROM reading after writing EEPROM reading cannot be performed after writing is performed.
Remedy:	Replace reader unit.

Error code:	E261-0000
Description:	Zero-cross signal error If failed to detect zero-cross signal cycle of the power supply when initializing. When the input of the zero-signal failed continuously for three seconds while controlling the temperature adjustment.
Causes:	The wiring is faulty (short circuit, open circuit). The main power supply PCB is faulty. The DC controller PCB is faulty.
Remedy:	- Replace the power supply PCB. - Replace the DC controller PCB.

Error code:	E280-0001
Description:	Reading unit communication error Reception status error
Remedy:	Disconnect and then connect the flexible cable. Replace the flexible cable

Error code:	E280-0002
Description:	Reading unit communication error Reception interrupt error
Remedy:	Disconnect and then connect the flexible cable. Replace the flexible cable

Error code:	E280-0003
Description:	Reading unit communication error Insufficient insertion of the reading unit connector
Remedy:	Disconnect and then connect the flexible cable. Replace the flexible cable

Error code:	E315-0007
Description:	There is an error in image data. There is an error in JBIG encoding.
Remedy:	Turn off and then back on the power.

Error code:	E315-000d
Description:	There is an error in image data. There is an error in JBIG decoding.
Remedy:	Turn off and then back on the power.

Error code:	E315-000e
Description:	Image data trouble Damaged data (trouble in memory or HDD) Software decoding error
Remedy:	Replace the image memory (SDRAM) or HDD.

Error code:	E315-0025
Description:	Abnormality of image data ASIC (for compression/decompression) on the image conversion PCB is faulty. Image data transfer error during rotation processing.
Remedy:	Check on connection of the image conversion board, Replace the image conversion board

Error code:	E315-0027
Description:	There is an error in image data. Error in ROTU timeout
Remedy:	Replace SDRAM. Replace HDD. Replace the main controller PCB.

Error code:	E315-0033
Description:	There is an error in image data. Error in MemFill hardware
Remedy:	Replace the main controller PCB.

Error code:	E315-0035
Description:	There is an error in image data. Error in MemFill timeout
Remedy:	Replace the main controller PCB.

Error code:	E315-0100
Description:	There is an error in image data. Error in PrcOverRun
Remedy:	Replace the main controller PCB.

Error code:	E315-0500
Description:	There is an error in image data. Error in device timeout [location to be detected] image process module (SCIO) [Detection timing] when there is no interruption 2 min after the operation has been started
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0501
Description:	There is an error in image data. Device: abnormal termination error [location to be detected] image process module (SCIO) [Detection timing] When abnormal interruption is detected after the operation has been started.
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0510
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (SCIP) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0511
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (SCIP) [Detection timing] when abnormal interruption is detected after the operation has been detected
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0520
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (CMIP) [Detection timing] When there is no interruption 2 min after the operation has been started
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0521
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (CMIP) [Detection timing] when abnormal interruption is detected after the operation has been detected
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB

Error code:	E315-0530
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (JPEN) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently.

Error code:	E315-0531
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (JPEN) [Detection timing] when abnormal interruption is detected after the operation has been started.
Remedy:	Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently.

Error code:	E315-0540
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (JPDE) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently.

Error code:	E315-0541
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (JPDE) [Detection timing] when abnormal interruption is detected after the operation has been started
Remedy:	Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently.

Error code:	E315-0550
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (PRIP) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Error code:	E315-0551
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (PRIP) [Detection timing] when abnormal interruption is detected after the operation has been started.
Remedy:	Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Error code:	E315-0560
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (PRIO) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Error code:	E315-0561
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (PRIO) [Detection timing] when abnormal interruption is detected after the operation has been started.
Remedy:	Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Error code:	E400-0001
Description:	Feeder communication error Checksum error
Remedy:	Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub).

Error code:	E400-0002
Description:	Feeder communication error Reception status error
Remedy:	Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub).

Error code:	E400-0003
Description:	Feeder communication error Reception interrupt error
Remedy:	Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub).

Error code:	E413-0001
Description:	Pressure motor trouble Pressure HP sensor OPEN
Remedy:	Replace the pressure motor.

Error code:	E413-0002
Description:	Pressure motor trouble Pressure HP sensor CLOSE
Remedy:	Replace the pressure motor.

Error code:	E490-0001
Description:	Wrong model error When the feeder of another model has been detected
Remedy:	Connect the feeder for this unit.

Error code:	E500-0001
Description:	Finisher communication error Data communication could not be performed normally. It has been retried three times in vain.
Remedy:	- Check the connectors of the finisher controller PCB and DC controller PCB for normal connection. - Replace the finisher controller PCB. - Replace the DC controller PCB.

Error code:	E503-0002
Description:	Saddle communication error When communication with the saddle stitcher is interrupted
Remedy:	- Check the connections between the saddle stitcher controller PCB and finisher controller PCB. - Replace the saddle stitcher controller PCB and finisher controller PCB.

Error code:	E503-0003
Description:	There is an error in the communication within the finisher (finisher R1/R2). finisher-to-punch unit communication error
Causes:	A communication error has been detected.
Remedy:	Check the connection between the Punch controller PCB and the finisher controller PCB.

Error code:	E505-0001
Description:	Finisher backup memory error When the checksum value calculated by the CPU differs from the checksum values of the data held inside the RAM
Causes:	The backup RAM is faulty.
Remedy:	Replace the finisher controller PCB.

Error code:	E505-0002
Description:	Finisher backup memory error When the verify processing is not completed even after 2000 ms have elapsed during data writing
Causes:	The EEPROM is faulty. The finisher controller PCB is faulty. The puncher driver PCB is faulty.
Remedy:	Replace the finisher controller PCB.

Error code:	E514-0001
Description:	End assist motor error Finisher-Q1/Q3, Saddle Finisher-Q2/Q4 The HP sensor fails to be OFF after the end assist motor rotates for a specific period of time.
Causes:	The stack delivery motor (M3) is faulty. The delivery belt home position motor (PI7) is faulty. The finisher controller PCB is faulty.
Remedy:	Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)

Error code:	E514-0002
Description:	End assist motor error Finisher-Q1/Q3, Saddle Finisher-Q2/Q4 The HP sensor fails to be ON after the end assist motor rotates for a specific period of time.
Causes:	The stack delivery motor (M3) is faulty. The delivery belt home position motor (PI7) is faulty. The finisher controller PCB is faulty.
Remedy:	Replace the end assist HP sensor (PI39) , Replace the end assist motor (M39)

Error code:	E519-0001
Description:	Gear change motor error Finisher-Q1/Q3, Saddle Finisher-Q2/Q4 The HP sensor fails to be OFF after the gear change motor rotates for a specific period of time.
Remedy:	Replace the gear change HP sensor (PI49) , Replace the gear change motor (M40)

Error code:	E519-0002
Description:	There is an error in the gear change motor (finisher R1/R2). The home position sensor does not go on within a specific period of time after the gear change motor has started to rotate.
Remedy:	1) Check the gear change home position sensor. Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor. Is the wiring normal? 3) Check the gear change mechanism. Is there a fault? 4) Try replacing the gear change motor. Is the problem corrected?

Error code:	E520-0001
Description:	- Offset motor or finisher controller PCB failure - Offset HP sensor failure - The offset motor was driven for 1000 ms in the HP sensor approach direction, but the offset HP sensor did not turn on.
Remedy:	- Check the connector of the offset HP sensor. - Check the connector of the offset motor. - Replace the offset HP sensor. - Replace the offset motor. - Replace the finisher controller PCB.

Error code:	E520-0002
Description:	- Offset motor or finisher controller PCB failure - Offset HP sensor failure - The offset motor was driven for 1000 ms in the HP sensor escape direction, but the offset HP sensor did not turn off.
Remedy:	- Check the connector of the offset HP sensor. - Check the connector of the offset motor. - Replace the offset HP sensor. - Replace the offset motor. - Replace the finisher controller PCB.

Error code:	E530-0001
Description:	There is a fault in alignment. Finisher-N1/Saddle Finisher-N2 There is an excess load on the alignment motor (M3), aligning plate home position sensor (PI6), or aligning plate. The aligning plate does not leave the aligning plate home position sensor when the alignment motor has been driven for 2 sec.
Causes:	The alignment motor (M3) is faulty. The alignment plate home position sensor (PI6) is faulty.
Remedy:	Replace the front adjuster plate HP sensor (PI36) , Replace the front adjuster plate motor (M33)

Error code:	E530-0002
Description:	There is a fault in alignment. Finisher-N1/Saddle Finisher-N2 There is an excess load on the rear alignment motor (M3), rear aligning plate home position sensor (PI6), or rear aligning plate. The aligning plate does not return to its home position when the aligning plate motor has been driven for 2 sec.
Causes:	The alignment motor (M3) is faulty. The alignment plate home position sensor (PI6) is faulty.
Remedy:	Replace the front adjuster plate HP sensor (PI36) , Replace the front adjuster plate motor (M33)

Error code:	E530-8001
Description:	Alignment error When the alignment plate fails to leave the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec.
Remedy:	Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106).

Error code:	E530-8002
Description:	Alignment error When the alignment plate fails to return to the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec.
Remedy:	Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106).

Error code:	E531-0001
Description:	- Staple unit failure - Staple HP sensor failure - Finisher controller PCB failure - The staple home position was not left when 400 ms have lapsed since start of staple operation.
Causes:	The stapler motor (M6) is faulty. The stapler home position sensor detecting switch (MS7) is faulty.
Remedy:	- Check the connector of the staple unit. - Replace the staple unit. - Replace the finisher controller PCB.

Error code:	E531-0002
Description:	- Staple unit failure - Staple HP sensor failure - Finisher controller PCB failure - The staple home position had been left once, but it was not reached again when 400 ms have lapsed since start of staple operation. In addition, the staple home position could not be reached by performing reverse operation for 400 ms.
Causes:	The stapler motor (M6) is faulty. The stapler home position sensor detecting switch (MS7) is faulty.
Remedy:	- Check the connector of the staple unit. - Replace the staple unit. - Replace the finisher controller PCB.

Error code:	E531-8001
Description:	Stapler error When the stapler fails to leave the stapler home position even though the stapler motor was driven for 0.5 sec.
Remedy:	Replace the stapler motor (M111) and stapler home position detection sensor (PI50).

Error code:	E531-8002
Description:	Stapler error When the stapler fails to return to the stapler home position even though the stapler motor was driven for 0.5 sec.
Remedy:	Replace the stapler motor (M111) and stapler home position detection sensor (PI50).

Error code:	E532-0001
Description:	There is a fault in the shift of the stapler. Finisher-N1/Saddle Finisher-N2 The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler shift base. The stapler shift base does not leave the stapler shift home position sensor when the stapler shift motor has been driven for 4 sec.
Causes:	The stapler shift motor (M4) is faulty. The stapler shift home position sensor (PI7) is faulty.
Remedy:	Replace the stapler shift HP sensor (PI50) , Replace the stapler shift motor (M35)

Error code:	E532-0002
Description:	There is a fault in the shift of the stapler. Finisher-N1/Saddle Finisher-N2 The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler shift base. The stapler shift base does not return from the stapler shift home position sensor when the stapler shift motor has been driven for 4 sec.
Causes:	The stapler shift motor (M4) is faulty. The stapler shift home position sensor (PI7) is faulty.
Remedy:	Replace the stapler shift HP sensor (PI50) , Replace the stapler shift motor (M35)

Error code:	E532-8001
Description:	There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go off within a specific period of time after the stapler shift motor has started to rotate.
Remedy:	1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected?

Error code:	E532-8002
Description:	There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go on within a specific period of time after the stapler shift motor has started to rotate.
Remedy:	1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected?

Error code:	E535-0001
Description:	There is a fault in the swing mechanism. Finisher-N1/Saddle Finisher-N2 The swing motor (M7) or the swing guide open sensor (PI18) is faulty. The swing guide closed switch does not go ON when the swing motor has been rotated in reverse for 1 sec.
Causes:	The delivery motor (M2) is faulty. The swing guide open sensor (PI18) is faulty.
Remedy:	Replace the swing HP sensor (PI35) , Replace the swing motor (M36)

Error code:	E535-0002
Description:	There is a fault in the swing mechanism. Finisher-N1/Saddle Finisher-N2 The swing motor (M7) or the swing guide closed switch (MS6) is faulty. The swing guide open switch does not go ON when the swing motor has been rotated in reverse for 1 sec.
Causes:	The safety area switch (MS3) is faulty. The swing guide open detecting switch (MS6) is faulty.
Remedy:	Replace the swing HP sensor (PI35) , Replace the swing motor (M36)

Error code:	E537-0001
Description:	Rear alignment error Finisher-Q1/Q3, Saddle Finisher-Q2/Q4 The HP sensor fails to be OFF after the swing motor rotates for a specific period of time.
Causes:	The alignment motor (front; M4) is faulty. The aligning plate home position sensor (front; PI4) is faulty. The finisher controller PCB is faulty.
Remedy:	Replace the rear adjuster plate HP sensor (PI37) , Replace the rear adjuster plate motor (M34)

Error code:	E537-0002
Description:	Rear alignment error Finisher-Q1/Q3, Saddle Finisher-Q2/Q4 The HP sensor fails to be ON after the swing motor rotates for a specific period of time.
Causes:	The alignment motor (front; M4) is faulty. The aligning plate home position sensor (front; PI4) is faulty. The finisher controller PCB is faulty.
Remedy:	Replace the rear adjuster plate HP sensor (PI37) , Replace the rear adjuster plate motor (M34)

Error code:	E537-8001
Description:	Front alignment error When the alignment plate fails to leave the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec.
Remedy:	Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107).

Error code:	E537-8002
Description:	Front alignment error When the alignment plate fails to return to the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec.
Remedy:	Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107).

Error code:	E540-0002
Description:	- Standard tray shift motor or finisher controller PCB failure - Standard tray HP sensor failure - Standard tray clock sensor failure - Standard tray shift motor load failure Cannot move (to the pickup position) within the specified time.
Causes:	The tray paper limit detecting switch (MS4) is faulty.
Remedy:	- Check the connector of the standard tray HP sensor. - Check the connector of the standard tray clock sensor. - Check the connector of the standard tray shift motor. - Replace the standard tray HP sensor. - Replace the standard tray clock sensor. - Replace the standard tray shift motor. - Replace the finisher controller PCB.

Error code:	E540-0003
Description:	- Standard tray shift motor or finisher controller PCB failure - Standard tray HP sensor failure - Standard tray clock sensor failure - Standard tray shift motor load failure The standard tray was operated, but it did not reach the sensor within 300 ms.
Causes:	The tray lifter motor (M5) is faulty. The tray lifter motor clock sensor 1/2 (PI19/PI20) is faulty.
Remedy:	- Check the connector of the standard tray HP sensor. - Check the connector of the standard tray clock sensor. - Check the connector of the standard tray shift motor. - Replace the standard tray HP sensor. - Replace the standard tray clock sensor. - Replace the standard tray shift motor. - Replace the finisher controller PCB.

Error code:	E540-0004
Description:	Stack tray up/down error Finisher-P1 Outputs of the top paper sensor, bottom paper sensor, tray upper limit sensor, and tray lower limit sensor have abnormality during paper surface detection.
Remedy:	Replace the stack tray top paper sensor (SR9) , Replace the stack tray bottom paper sensor (SR10) , Replace the stack tray upper limit sensor (SR13) , Replace the stack tray lower limit sensor (SR12) , Replace the stack tray shift motor (M7)

Error code:	E540-8002
Description:	Tray up/down error When a danger area is reached before the sheet level is detected by the 1st tray sheet level detection sensor during the sheet level detection operation - When a discontinuous area was detected during the tray operation
Remedy:	- Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107)

Error code:	E540-8003
Description:	Tray up/down error When the input of the clock signal could not be detected within 0.2 sec. during the operation of the 1st tray shift motor
Remedy:	- Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107)

Error code:	E542-0002
Description:	- Optional tray motor or finisher controller PCB failure - Optional tray HP sensor failure - Optional tray clock sensor failure - Optional tray shift motor load failure Cannot move (to the pickup position) within the specified time.
Remedy:	- Check the connector of the optional tray HP sensor. - Check the connector of the optional tray clock sensor. - Check the connector of the optional tray shift motor. - Replace the optional tray HP sensor. - Replace the optional tray clock sensor. - Replace the optional tray shift motor. - Replace the finisher controller PCB.

Error code:	E542-0003
Description:	- Optional tray motor or finisher controller PCB failure - Optional tray HP sensor failure - Optional tray clock sensor failure - Optional tray shift motor load failure - The optional tray was moved upward, but it did not reach the HP sensor within 3000 ms.
Remedy:	- Check the connector of the optional tray HP sensor. - Check the connector of the optional tray clock sensor. - Check the connector of the optional tray shift motor. - Replace the optional tray HP sensor. - Replace the optional tray clock sensor. - Replace the optional tray shift motor. - Replace the finisher controller PCB.

Error code:	E577-8001
Description:	Paddle error Finisher-Z1 The HP sensor fails to be ON within 1500ms after the paper retaining paddle starts to move to its HP.
Remedy:	Replace the paddle HP sensor (SR8) , Replace the paddle motor (M6)

Error code:	E577-8002
Description:	Paddle error Finisher-Z1 The HP sensor fails to be OFF within 1000ms after the paper retaining paddle starts to move from its HP.
Remedy:	Replace the paddle HP sensor (SR8) , Replace the paddle motor (M6)

Error code:	E584-0001
Description:	- Shutter drive motor or finisher controller PCB failure - Shutter open detection sensor failure - Shutter clutch failure - The shutter open sensor did not turn on when 1000 ms have lapsed since the shutter unit had performed open operation, resulting in incomplete open operation
Causes:	The feed motor (M1) is faulty. The shutter closed detecting switch (MS4) is faulty.PI20
Remedy:	- Check the connector of the shutter open sensor. - Check the connector of the shutter clutch. - Check the connector of the shutter motor. - Replace the shutter open sensor. - Replace the shutter clutch. - Replace the shutter drive motor. - Replace the finisher controller PCB.

Error code:	E584-0002
Description:	- Shutter drive motor or finisher controller PCB failure - Shutter open detection sensor failure - Shutter clutch failure - The shutter open sensor did not turn off when 1000 ms have lapsed since the shutter unit had performed close operation, resulting in incomplete close operation.
Causes:	The feed motor (M1) is faulty. The shutter open sensor (PI5) is faulty.
Remedy:	- Check the connector of the shutter open sensor. - Check the connector of the shutter clutch. - Check the connector of the shutter motor. - Replace the shutter open sensor. - Replace the shutter clutch. - Replace the shutter drive motor. - Replace the finisher controller PCB.

Error code:	E590-0001
Description:	Puncher motor error The puncher HP sensor fails to be detected after the puncher motor is driven for 200ms.
Causes:	The puncher home position sensor (PI1P) is faulty. The puncher motor (M1P) is faulty. The puncher motor clock sensor (PI3P) is faulty. The puncher driver PCB is faulty.
Remedy:	Replace the puncher HP sensor, Replace the puncher motor

Error code:	E590-0002
Description:	Puncher motor error The puncher fails to detect the puncher HP sensor after the puncher motor stops during initial operation.
Causes:	The puncher home position sensor (PI1P) is faulty. The puncher motor (M1P) is faulty. The puncher motor clock sensor (PI3P) is faulty. The puncher driver PCB is faulty.
Remedy:	Replace the puncher HP sensor, Replace the puncher motor

Error code:	E591-0001
Description:	Puncher dust sensor error Light receiving voltage at the time of light emission is abnormal.
Remedy:	Replace the puncher dust sensor

Error code:	E591-0002
Description:	Puncher dust sensor error Light receiving voltage at the time of non-light-emission is abnormal.
Remedy:	Replace the puncher dust sensor

Error code:	E592-0001
Description:	Puncher side registration sensor error Light receiving voltage at the time of light emission is abnormal.
Remedy:	Replace the end sensor

Error code:	E592-0002
Description:	Puncher side registration sensor error Light receiving voltage at the time of non-light-emission is abnormal.
Remedy:	Replace the end sensor

Error code:	E592-0003
Description:	Puncher side registration sensor error Light receiving voltage at the time of light emission is abnormal.
Remedy:	Replace the side registration sensor 1

Error code:	E592-0004
Description:	Puncher side registration sensor error Light receiving voltage at the time of non-light-emission is abnormal.
Remedy:	Replace the side registration sensor 1

Error code:	E592-0005
Description:	Puncher side registration sensor error Light receiving voltage at the time of light emission is abnormal.
Remedy:	Replace the side registration sensor 2

Error code:	E592-0006
Description:	Puncher side registration sensor error Light receiving voltage at the time of non-light-emission is abnormal.
Causes:	The horizontal registration sensor is faulty. The puncher waste sensor is faulty. The puncher driver PCB is faulty.
Remedy:	Replace the side registration sensor 2

Error code:	E592-0007
Description:	Puncher side registration sensor error Light receiving voltage at the time of light emission is abnormal.
Remedy:	Replace the side registration sensor 3

Error code:	E592-0008
Description:	Puncher side registration sensor error Light receiving voltage at the time of non-light-emission is abnormal.
Remedy:	Replace the side registration sensor 3

Error code:	E592-0009
Description:	Puncher side registration sensor error Light receiving voltage at the time of light emission is abnormal.
Remedy:	Replace the side registration sensor 4

Error code:	E592-000A
Description:	Puncher side registration sensor error Light receiving voltage at the time of non-light-emission is abnormal.
Remedy:	Replace the side registration sensor 4

Error code:	E593-0001
Description:	Puncher shift motor error The HP sensor fails to be OFF.
Causes:	The horizontal registration home position sensor (PI2P) is faulty. The puncher shift motor (M2P) is faulty. The puncher drive PCB is faulty
Remedy:	Replace the HP sensor, Replace the puncher shift motor

Error code:	E593-0002
Description:	Puncher shift motor error The HP sensor fails to be ON.
Causes:	The horizontal registration home position sensor (PI2P) is faulty. The puncher shift motor (M2P) is faulty. The puncher drive PCB is faulty
Remedy:	Replace the HP sensor, Replace the puncher shift motor

Error code:	E5F0-0001
Description:	There is an error in saddle paper positioning. The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for 1.33 sec. The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty.
Causes:	The positioning plate motor (M4S) is faulty. The power positioning plate home position sensor (PI7S) is faulty.
Remedy:	Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S).

Error code:	E5F0-0002
Description:	There is an error in saddle paper positioning. The paper positioning plate home position sensor does not turn off when the paper positioning plate motor has been driven for 1 sec. The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty.
Causes:	The positioning plate motor (M4S) is faulty. The power positioning plate home position sensor (PI7S) is faulty.
Remedy:	Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S).

Error code:	E5F1-0001
Description:	There is an error in saddle paper folding. The number of detection pulses of the paper folding motor clock sensor is lower than specified. The paper folding home position sensor or the paper folding motor clock sensor (P14S) is faulty.
Causes:	The folding motor (M2S) is faulty. The folding motor clock sensor (PI4S) is faulty.
Remedy:	Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S).

Error code:	E5F1-0002
Description:	There is an error in saddle paper folding. The state of the paper folding home position sensor does not change when the paper folding motor has been driven for 3 sec. The paper folding motor (M2S) or the paper folding motor clock sensor (P14S) is faulty.
Causes:	The folding roller home position sensor (PI12) is faulty. The stapler/folder motor (M7) is faulty. The stapler/folder clock sensor (PI14) is faulty. The finisher controller PCB is faulty.
Remedy:	Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S).

Error code:	E5F2-0001
Description:	There is an error in the saddle guide. The guide home position sensor does not turn on when the guide motor has been driven for 0.45 sec. The guide motor (M3S) or the guide home position sensor (PI3S) is faulty.
Causes:	The guide motor (M3S) is faulty. The guide home position sensor (PI13S) is faulty.
Remedy:	Check the guide motor (M3S) /guide home position sensor (PI13S).

Error code:	E5F2-0002
Description:	There is an error in the saddle guide. The guide home position sensor doest not turn off when the guide motor has been driven for 1 sec. The guide motor (M3S) or the guide home position sensor (PI3S) is faulty.
Causes:	The guide motor (M3S) is faulty. The guide home position sensor (PI13S) is faulty.
Remedy:	Check the guide motor (M3S) /guide home position sensor (PI13S).

Error code:	E5F3-0001
Description:	There is an error in saddle alignment. The aligning plate home position sensors does not turn on when the alignment motor has been driven for 05. sec (during initialization, 1.67 sec). The alignment motor (M5S) or the aligning plate home position sensor (PI5S) is faulty.
Causes:	The alignment motor (M5S) is faulty. The alignment plate home position sensor (PI5S) is faulty.
Remedy:	Check the alignment motor (M5S) /aligning plate home position sensor (PI5S).

Error code:	E5F3-0002
Description:	There is an error in saddle alignment. The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec. The alignment motor (M5S) for the alignment plate home position sensor (PI5S) is faulty.
Causes:	The alignment motor (M5S) is faulty. The alignment plate home position sensor (PI5S) is faulty.
Remedy:	Check the alignment motor (M5S) /aligning plate home position sensor (PI5S).

Error code:	E5F4-0001
Description:	There is an error in saddle rear sampling. The stitching home position sensor does not turn on when the stapler motor (rear) is rotated in reverse for 0.5 sec or more. The switch motor (rear, M65) or the stitching home position sensor (rear, MS5S) is faulty.
Causes:	The stitch motor (rear, M6S) is faulty. The stitching home position switch (rear, PS2S) is faulty.
Remedy:	Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S)

Error code:	E5F4-0002
Description:	There is an error in saddle rear sampling. The stitching home position sensor does not turn off when the switch motor (rear) is reverse for 0.5 sec or more. The switch motor (rear, M6S) or the stitching home position sensor (rear, MS5S) is faulty.
Causes:	The stitch motor (rear, M6S) is faulty. The stitching home position switch (rear, PS2S) is faulty.
Remedy:	Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S).

Error code:	E5F5-0001
Description:	There is an error in saddle front stapling. The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0.5 sec or more. The stitch motor (front, M7S) or the stitching home position sensor (front, MS7S) is faulty.
Causes:	The stitching motor (front, M7S) is faulty. The stitching motor operating home position switch (front, PS4S) is faulty.
Remedy:	Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S).

Error code:	E5F5-0002
Description:	There is an error in saddle front stapling. The stitching home position sensor does not turn off when the switch motor (front) is rotated in normal direction for 0.5. The stitch motor (front, M7S) or the switching home position sensor (front, MS7S) is faulty.
Causes:	The stitching motor (front, M7S) is faulty. The stitching motor operating home position switch (front, PS4S) is faulty.
Remedy:	Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S).

Error code:	E5F6-0001
Description:	There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4S) is faulty. The paper pushing plate home position sensor does not go ON when the paper pushing plate motor has been driven for 0.3 sec or more.
Causes:	The paper push-on plate motor (M8S) is faulty. The paper push-on plate home position sensor (PI14S) is faulty.
Remedy:	Replace the paper pressure plate motor (M8S), Replace the paper pressure plate HP sensor (PI14S)

Error code:	E5F6-0002
Description:	There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI14S) is faulty. The paper pushing plate home position sensor does not go OFF when the paper pushing plate motor has been driven for 80 msec.
Causes:	The paper push-on plate motor (M8S) is faulty. The paper push-on plate leading edge position sensor (PI15S) is faulty.
Remedy:	Replace the paper pressure plate motor (M8S), Replace the paper pressure plate HP sensor (PI14S)

Error code:	E5F6-0003
Description:	There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty. The paper pushing plate leading edge position sensor does not go OFF when the paper pushing plate motor has been driven for 80 msec.
Causes:	The paper push-on plate motor (M8S) is faulty. The paper push-on plate leading edge position sensor (PI15S) is faulty.
Remedy:	Replace the paper pressure plate motor (M8S), Replace the paper pressure plate motor clock sensor (PI1S)

Error code:	E5F6-0004
Description:	There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate motor clock sensor (PI1S) is faulty. The number of detection pulses of the paper pushing plate motor clock sensor has dropped below a specific value.
Causes:	The paper push-on plate motor (M8S) is faulty. The paper push-on plate motor clock sensor (PIS) is faulty
Remedy:	Replace the paper pressure plate motor (M8S), Replace the paper pressure plate leading edge sensor (PI15S)

Error code:	E5F6-0005
Description:	There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty. The paper pushing plate leading edge positioning sensor does not go ON when the paper pushing plate motor has been driven for 0.3 sec or more.
Causes:	The paper push-on plate motor (M8S) is faulty. The paper push-on leading edge position sensor (PI15S) is faulty.
Remedy:	Replace the paper pressure plate motor (M8S), Replace the paper pressure plate leading edge sensor (PI15S)

Error code:	E5F8-0001
Description:	There is an error in the saddle connector. The connector of the guide home position sensor is identified as being disconnected. The connector of the guide home position sensor (PI3S) is faulty.
Causes:	The guide home position sensor (PI13S) has a faulty connector.
Remedy:	Check the connectors of the guide home position sensor (PI13S). Check the connectors of the paper pushing plate home position sensor (PI4S).

Error code:	E5F8-0002
Description:	There is an error in the saddle connector. The connector of the paper pushing plate home position sensor is identified as being disconnected. The connector of the paper pushing plate home position sensor (PI14S) is faulty.
Causes:	The paper push-on plate home position sensor (PI14) has a faulty connector.
Remedy:	Check the connectors of the paper pushing plate leading edge position sensor (PI5S).

Error code:	E5F8-0003
Description:	There is an error in the saddle connector. The connector of the paper pushing plate leading edge position sensor is identified as being disconnected. The connector of the paper pushing plate leading edge sensor (PI15S) is faulty.
Causes:	The paper push-on plate leading edge sensor (PI15S) has a faulty connector.
Remedy:	Check the connectors of the paper pushing plate leading edge position sensor (PI5S).

Error code:	E5F9-0001
Description:	There is an error in the saddle switch. With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open. The inlet cover switch (MS1S), front cover switch (MS2S), or delivery cover switch (MS3S) is faulty.
Causes:	The inlet door open detecting switch (MS1S) is faulty. The inlet door sensor (PI9S) is faulty.
Remedy:	Check the inlet cover switch (MS1S)/front cover switch (MS2S)/delivery cover switch (MS3S).

Error code:	E5F9-0002
Description:	There is an error in the saddle switch. With any of the following sensor is identifying its respective cover as being closed, the front cove switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cove sensor (PI3S) The front cove switch (MS2S) or the delivery cover switch (MS3S) is faulty.
Causes:	The front door open detecting switch (MS2S) is faulty. The front door open sensor (PS2S) is faulty.
Remedy:	Check the front cover switch (MS2S)/delivery cover switch (MS3S).

Error code:	E5F9-0003
Description:	There is an error in the saddle switch. With any of the following sensors identifying its respective cover as being closed, the delivery cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - delivery cover switch (MS3S)
Causes:	The delivery door open detecting switch (MS3S) is faulty. The delivery door open sensor (PI3S) is faulty.
Remedy:	Check the delivery cover switch (MS3S).

Error code:	E602-0001
Description:	HDD error
Causes:	Lack of the HDD capacity The capacity of the HDD installed is smaller than that of the HDD used in the software.

Error code:	E602-0002
Description:	HDD error
Causes:	Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged.
Remedy:	Burn the Bootable CD again.

Error code:	E602-0003
Description:	HDD error
Causes:	HDD access error An error occurred caused by the device or hardware when accessing to the HDD during execution of bootrom. (Damage to the sector / Busy device status, etc.)
Remedy:	Turn on the power again.

Error code:	E602-0006
Description:	HDD error
Causes:	SubBootable load failure A SubBootable CD was not contained. A SubBootable CD was damaged.
Remedy:	Burn the SubBootable CD again.

Error code:	E602-0007
Description:	HDD error
Causes:	The contents (ICC-Profile, etc.) could not be detected. (The contents were not contained. The contents were damaged, etc.)
Remedy:	Burn the Bootable CD again.

Error code:	E602-01XX
Description:	There is an error on the hard disk. /DOSDEV is faulty

Error code:	E602-02XX
Description:	There is an error on the hard disk. /FSTDEV is faulty.

Error code:	E602-03XX
Description:	There is an error on the hard disk. /DOSDEV2 is faulty.

Error code:	E602-04XX
Description:	There is an error on the hard disk. /FSTPDEV is faulty.

Error code:	E602-05XX
Description:	There is an error on the hard disk. /DOSDEV3 is faulty.

Error code:	E602-06XX
Description:	There is an error on the hard disk. /PDLDEV is faulty.

Error code:	E602-07XX
Description:	There is an error on the hard disk. /DOSDEV4 is faulty.

Error code:	E602-08XX
Description:	There is an error on the hard disk. /BOOTDEV is faulty.

Error code:	E602-09XX
Description:	There is an error on the hard disk. /DOSDEV5 is faulty.

Error code:	E602-FFXX
Description:	There is an error on the hard disk. There is an error in a partition that cannot be identified.

Error code:	E604-0000
Description:	Memory error
Causes:	Lack of memory capacity
Remedy:	Check the memory capacity inserted to each slot.

Error code:	E609-0008
Description:	Hard disk trouble When the HDD fails to reach the prescribed temperature within the prescribed period of time when it is started up
Remedy:	Replace with an HDD which is guaranteed to operate at low temperatures.

Error code:	E609-0009
Description:	Hard disk trouble When the HDD fails to reach the prescribed temperature when its operation is restored from the sleep mode
Remedy:	Replace with an HDD which is guaranteed to operate at low temperatures.

Error code:	E610
Description:	1st Image Transfer ATVC (color) failure - An abnormal average value is detected while performing the first image transfer ATVC of color.
Causes:	• Transfer Belt Unit • Transfer Roller • High Voltage Unit
Remedy:	1 Check if the Transfer Roller and Transfer Belt are dirty and correct as necessary. - - 2 Change High Voltage Unit - - 3 Change Transfer Belt Unit

Error code:	E677-0001
Description:	DPRAM size error In communication for initialization, the DPRAM size returned by the PDL board to the host machine has an error. (The host machine is aware of the DPRAM size in advance; the DPRAM is a dual-port RAM used for communication between the host machine and the PDL board, and is mounted on the PDL board.)
Causes:	The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty.
Remedy:	1. Connector Is the printer board (accessory) connected correctly? NO: Correct the connection. 2. Printer board, Main controller PCB Try replacing the printer board. Is the problem corrected? YES: End. NO: Replace the main controller PCB.

Error code:	E677-0003
Description:	There is an external controller error. An error has been detected by a check on the configuration when the external controller is being started up.
Remedy:	Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external contro

Error code:	E677-0004
Description:	PDL board disconnection After the connection of the PDL board is recognized at power-on, the PDL board is disconnected. During power-up, monitoring is executed at intervals of 2 min; however, if the CPU is not on (sleep state or the like), no error will be identified even if the PDL board is discontented. If the PDL board is disconnected in sleep state, the absence of the PDL board will be recognized at the start of the CPU.
Causes:	The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty.
Remedy:	- Check connection of the connector for cooling CPU - Replace CPU cooling fan

Error code:	E677-0010
Description:	There is an external controller error. A controller for a non-Canon machine is connected.
Remedy:	Turn off the main power, and check the controller is an appropriate type, and check the cable; then turn on the main power. If the machine fails to reset, re-install the system software of the external controller.

Error code:	E677-0080
Description:	There is an external controller error. There is an error in the communication with the printer after the external controller has started up normally.
Causes:	The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty.
Remedy:	Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external controller.

Error code:	E710-0001
Description:	IPC initializing error When the ready status fails to be established within 3 sec. after the IPC chip started up
Causes:	The DC controller PCB is faulty. The reader controller PCB is faulty. The machine controller PCB is faulty.
Remedy:	Check the cable connections.

Error code:	E711-0001
Description:	IPC communication error When error occurrence was set 4 or more times in the error register of the IPC chip within 1.5 sec.
Causes:	The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty.
Remedy:	Check the cable connections. Replace the ADF controller PCB. Replace the reader controller PCB.

Error code:	E713-0000
Description:	Communication error between the finisher and the printer Communication between the finisher and the copier stops.
Causes:	The connector has poor connection. The option power supply PCB is faulty. The finisher controller PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check on connection of the cable, Replace the finisher controller PCB, Replace the DC controller PCB

Error code:	E716-0000
Description:	Erroneous communication with optional cassette Disconnection of the optional cassette was detected after power-on, detection of normal connection to the optional cassette, and start of communication.
Causes:	The connector has poor connection. The main power supply PCB is faulty. The pedestal controller PCB is faulty. The DC controller PCB is faulty.
Remedy:	- Check the connectors of the optional cassette PCB and DC controller PCB. - Replace the optional cassette PCB for normal connection. - Replace the DC controller PCB.

Error code:	E716-0010
Description:	There is an error in the communication with the pedestal. When the communication with the 3 Way Unit-A1 is faulty after detecting the connection with the finisher.
Remedy:	Install the 3 Way Unit-A1. Replace the DC controller PCB after checking the cable

Error code:	E717-0001
Description:	Error in communication with NE controller When the NE controller which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Causes:	The wiring is faulty (short circuit, open circuit). The DA unit PCB is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the cable connections.

Error code:	E717-0002
Description:	Error in communication with NE controller When the IPC has a broken or disconnected wire or when an error has occurred where IPC communication cannot be recovered
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR.

Error code:	E719-0001
Description:	Error in communication with coin vendor/card reader When the coin vendor which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Causes:	The wiring is faulty (short circuit, open circuit). The Card Reader-C1 is faulty. The coin vendor is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the cable connections.

Error code:	E719-0002
Description:	Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.)
Causes:	Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.)
Remedy:	- Check the connection between the image processor PCB and serial PCB. - Check the connectors of the serial PCB and coin vendor for normal connection. - Replace the serial PCB. - Check the coin vendor. - Replace the image processor PCB.

Error code:	E719-0003
Description:	There is a coin vendor error. While the unit price is being checked at startup, an error occurs in the communication with the coin vendor.
Remedy:	Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E719-0011
Description:	Error in communication with coin vendor/card reader When the card reader which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR

Error code:	E719-0012
Description:	Error in communication with coin vendor/card reader When a wire in the IPC cable connected with the card reader is broken or disconnected or when an error has occurred where IPC communication cannot be recovered
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR

Error code:	E719-0031
Description:	There is a coin vendor error. Error in communication at card reader (serial) startup Communication with the card reader cannot be started at startup.
Remedy:	1. Check the connection of the cable for the card reader (connector disconnected, cable cut); thereafter, reset the condition in service mode: COPIER > FUNCTION > CLEAR > ERR. 2. Execute the following items in service mode after removing the card reader, and then install the card reader again. - COPIER > FUNCTION > CLEAR > CARD - COPIER > FUNCTION > CLEAR > ERR

Error code:	E719-0032
Description:	There is a coin vendor error. Error in communication after card reader (serial) startup Communication with the card reader is available at startup, and then becomes unavailable.
Remedy:	Check the connection of the cable for the card reader (connector disconnected, cable cut); thereafter, reset the condition in service mode: COPIER > FUNCTION > CLEAR > ERR.

Error code:	E730-1001
Description:	There is a PDL software error. An initialization error has occurred.
Remedy:	- Execute PDL resetting. - Turn on the power once again.

Error code:	E730-100A
Description:	Printer service call

Error code:	E730-9004
Description:	There is a PDL software error. There is an error in the communication (PAI) with an external controller.
Remedy:	- Turn on the power once main. - Check the connection of the open I/F board and the cable. - Replace the board for the external controller open I/F. - Replace the main controller PCB.

Error code:	E730-9005
Description:	There is a PDL software error. Fault in the connector of the vide cable to the external controller
Remedy:	- Turn on the power once main. - Check the connection of the open I/F board and the cable. - Replace the board for the external controller open I/F. - Replace the main controller PCB.

Error code:	E730-A006
Description:	There is a PDL software error. The PDL board does not respond. A subbootable is faulty or absent.
Remedy:	- Execute PDL resetting. - Turn on the power once again. - Check the connection of the UFR board. - Re-install the firmware. - Replace the main controller PCB.

Error code:	E730-A007
Description:	There is a PDL software error. There is a mismatch between the control software of the machine and the PDL control software in regard to version.
Remedy:	- Execute PDL resetting. - Turn on the power once again. - Execute system formatting (all), and reinstall the system.

Error code:	E730-B013
Description:	There is a PDL software error. Corruption in the font data
Remedy:	- Turn on the power once again. - Re-install the Software. - Execute system formatting (all), and reinstall the system.

Error code:	E732-0001
Description:	Scanner communication error
Causes:	Scanner communication error
Remedy:	1. Update the firmware. 2. Replace the Main Controller PCB.

Error code:	E732-0010
Description:	There is an error in the communication with the scanner Fault in detection of DDI-S Vsync signal
Remedy:	1. Check the connector used to connect the scanner. 2. Check the power supply of the scanner (to see if initialization takes place at startup). 3. Replace the reader controller, scanner board, or main board as necessary.

Error code:	E732-9999
Description:	There is an error in reader communication. Although a printer model, the machine is identified as a reader unit at start-up. (A copier model is started up as a printer model when the RAM is initialized.)
Remedy:	Turn off and then on the main power.

Error code:	E733-0000
Description:	Erroneous communication between controller and printer Cannot communicate with the printer at startup.
Causes:	Printer communication error (communication error at initial communication and negotiation packet error)
Remedy:	- Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB.

Error code:	E733-0001
Description:	Printer communication error (Invalid communication after communication is established, Parity error)
Remedy:	Turn on the power again. Replace the DC controller PCB.

Error code:	E733-0010
Description:	There is an error in the communication with the printer Fault in detection of DDI-P Vsync signal
Remedy:	1. Check the connection with the printer. 2. Check the power supply of the printer (to see if initialization takes place at startup). 3. Replace the DC controller or the main board.

Error code:	E733-0020
Description:	There is an error in the communication with the printer Error in DDI-P communication
Remedy:	2. Check the power supply of the printer (to see if initialization takes place at startup). 3. Replace the DC controller or the main board.

Error code:	E733-0021
Description:	There is an error in the communication with the printer Error in DDI-P communication
Remedy:	1. Check the connection with the printer. 2. Check the power supply of the printer (to see if initialization takes place at startup). 3. Replace the DC controller or the main board.

Error code:	E740-0002
Description:	Error detection on either Network Board or Mac address
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board.

Error code:	E743-0000
Description:	Error in main controller communication An error in reading of/writing to the Flash ROM in the Main Controller occurred.
Causes:	Software sequence error
Remedy:	1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB.

Error code:	E744-0001
Description:	Language file/boot ROM/USB memory error The language file version does not match Bootable.
Causes:	Language file version error The language file version does not match Bootable.
Remedy:	Download a language file of the correct version.

Error code:	E744-0002
Description:	Language file/boot ROM/USB memory error The language file is longer than the permitted size.
Causes:	Language file size error The language file is longer than the permitted size.
Remedy:	Download a language file of the correct version.

Error code:	E744-0003
Description:	Language file/boot ROM/USB memory error The language file version does not match Bootable
Causes:	Language file version error The language file version does not match Bootable.

Error code:	E744-0004
Description:	Language file/boot ROM/USB memory error Language file read error
Causes:	Language file read error Reading of language file is invalid.
Remedy:	Download a language file of the correct version.

Error code:	E744-1000
Description:	Mismatch of the series or model of the firmware sent at the time of downloading
Remedy:	Check the supported series or model of the firmware, and burn the correct series or model of firmware.

Error code:	E744-2000
Description:	There is an error in the language file/boot ROM. The engine ID indicated by the software ID is illegal.
Remedy:	Replace it with a software ID of the correct model.

Error code:	E744-3xxx
Description:	There is an error in the language file/boot ROM. Disagreement between the installed memory and the boot ROM
Remedy:	Confirm and correct the installed memory and the boot ROM.

Error code:	E745-0001
Description:	There is a fault on the TokeRing board. An attempt at PCI initialization has failed.
Remedy:	1. Disconnect and then connect the TokeRing board. 2. Replace the TokeRing board.

Error code:	E745-0002
Description:	There is a fault on the TokeRing board. The MAC address is faulty
Remedy:	1. Replace the TokenRing board.

Error code:	E745-0003
Description:	There is a fault on the TokeRing board. There is an error in the acquisition/setting of board information.
Remedy:	1. Replace the TokenRing board.

Error code:	E745-0004
Description:	There is a fault on the TokeRing board. There is a connection error
Remedy:	1. Check the connection of the cable. 2. Replace the cable. 3. Check the power source of the MAU. 4. Replace the MAU. 5. Replace the TokenRing board.

Error code:	E745-0005
Description:	There is a fault on the TokeRing board. Other Errors

Error code:	E746-0003
Description:	The accessories board is of the wrong type. At time of start-up, the UFR board is found to be of the wrong type. (A query is made to find out if the type is correct with reference to the engine ID.)
Remedy:	Replace it with a UFR board of the correct type.

Error code:	E748-2000
Description:	There is a mismatch between controller board and SDRAM size. An error occurs when accessing the chip on the main controller PCB.
Remedy:	Replace the main controller PCB.

Error code:	E748-2001
Description:	There is a mismatch between controller board and SDRAM size. An error occurs when accessing the memory on the main controller PCB.
Remedy:	1. Unplug/plug in the memory. 2. Replace the main controller PCB.

Error code:	E748-4910
Description:	There is a mismatch between controller board and SDRAM size. A controller board that does not match the product is defected.
Remedy:	- Replace the main controller PCB.

Error code:	E804-0000
Description:	Power supply fan failure

Error code:	E804-0001
Description:	Controller fan error Stop of power supply cooling fan 2 was detected
Remedy:	Check the connection of power supply cooling fan 2, replace it

Error code:	E805-0000
Description:	Fan failure The fan is faulty.
Causes:	Fixing fan error Cause The fixing fan is faulty. The engine controller PCB is faulty.
Remedy:	- Check the fan connector. - Replace the fan. - Replace the DC controller PCB.

Error code:	E805-0001
Description:	Error in duplex cooling fan
Causes:	Fan 1 failure

Error code:	E805-0002
Description:	Fan Motor 2 error
Causes:	The Sub Fan fails to rotate at the specified rotation speed.
Remedy:	1. Check the connection of the Sub Fan. 2. Replace the Sub Fan.

Error code:	E805-0003
Description:	Fan failure
Causes:	Controller fan failure detected The controller fan does not rotate because some kind of failure occurred in it.
Remedy:	Replace the controller fan.

Error code:	E911
Description:	Error in memory leak

Canon imageRUNNER 3225

Общие характеристики

Тип

Технология печати

Размещение

Цветность печати

Макс. формат

Печать фотографий

Факс

Телефон

Тип устройства

Копир

Сканер

Принтер

Пигментные чернила

Система непрерывной подачи чернил

Прямая печать

Печать без полей

Время разогрева

Двусторонняя печать

Макс, разрешение для ч/б печати

Скорость ч/б печати

Копир

Макс, количество копий за цикл

Время выхода первой копии

Макс, разрешение (ч/б)

Скорость ч/б копирования

Сканер

Глубина цвета

Оттенки серого

Емкость устройства автоподачи оригиналов

Тип сканера

Отправка изображения по e-mail

Стандарт TWAIN

Устройство автоподачи оригиналов

Макс. формат оригинала

Стандарт WIA

Разрешение сканера

Расходные материалы

Количество картриджей

Печать на:

Плотность бумаги

Факс

Цветной

PC Fax

Телефон

Беспроводная трубка

Проводная трубка

АОН

Caller ID

Автоответчик

Стандарт DECT

Спикерфон

Шрифты и языки управления

Языки управления

Количество установленных шрифтов

Лотки

Емкость лотка ручной подачи

Подача бумаги

Вывод бумаги

Финишер

Сортировка со сдвигом

Брошюровщик

Степлер

Электронная сортировка

Сортер

Интерфейсы

FireWire (IEEE 1394)

Ethernet (RJ-45)

Устройство для чтения карт памяти

Веб-интерфейс

RS-232

Инфракрасный порт

AirPrint

LPT

Bluetooth

Wi-Fi 802.11n

Wi-Fi

USB

Версия USB