Canon imageRUNNER 6000
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Скорость печати
A4
60
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Тип устройства |
МФУ |
Телефон |
|
Копир |
|
Печать фотографий |
|
Сканер |
|
Факс |
|
Размещение |
напольный |
Цветность печати |
|
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Макс. формат |
A3 |
Принтер |
|
Печать без полей |
|
Прямая печать |
|
Пигментные чернила |
|
Двусторонняя печать |
|
Время разогрева |
360 |
Макс, разрешение для ч/б печати |
|
| По X | 2 400 |
| По Y | 1 200 |
Скорость ч/б печати |
|
| A4 | 60 |
Копир |
|
Макс, количество копий за цикл |
999 |
Время выхода первой копии |
4 |
Шаг масштабирования |
0,01 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По X | 1 200 |
| По Y | 600 |
Скорость ч/б копирования |
|
| A3 | 30 |
Сканер |
|
Оттенки серого |
256 |
Макс. формат оригинала |
A3 |
Устройство автоподачи оригиналов |
одностороннее |
Разрешение сканера |
|
| По Х | 600 |
Расходные материалы |
|
Печать на: |
|
| Глянцевой бумаге |
|
| Карточках |
|
| Рулоне |
|
| CD/DVD |
|
| Пленках |
|
| Конвертах |
|
| Фотобумаге |
|
| Этикетках |
|
| Матовой бумаге |
|
Плотность бумаги |
|
| Максимальная | 200 |
| Минимальная | 64 |
Телефон |
|
Стандарт DECT |
|
Спикерфон |
|
Проводная трубка |
|
Беспроводная трубка |
|
АОН |
|
Caller ID |
|
Автоответчик |
|
Языки управления |
|
| PPDS |
|
| PCL 6 |
|
| PCL 5e |
|
| PostScript 3 |
|
| PostScript |
|
| PostScript 2 |
|
| PCL 5c |
|
|
|
|
Лотки |
|
Подача бумаги |
|
| Стандартная | 4 150 |
Вывод бумаги |
|
| Стандартный | 600 |
Финишер |
|
Степлер |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Сортер |
|
Брошюровщик |
|
Интерфейсы |
|
Веб-интерфейс |
|
Инфракрасный порт |
|
Ethernet (RJ-45) |
|
Bluetooth |
|
Wi-Fi |
|
FireWire (IEEE 1394) |
|
RS-232 |
|
Устройство для чтения карт памяти |
|
Память/Процессор |
|
Объем памяти |
192 |
Емкость жесткого диска |
10 |
Дополнительная информация |
|
Поддержка ОС |
|
| DOS |
|
| Windows |
|
Потребляемая мощность |
|
| При работе | 1 500 |
Габариты |
|
Глубина |
1 136 |
Ширина |
643 |
Высота |
743 |
Вес |
210 |
Модули
Printer & Accessories
Stand Unit
Carriage, Tube Unit & Film Strip
Cutter & Access Cover Lock Unit
ROLL UNIT LEFT (OPTION)
Electrical Parts
Tool
Ink Tank & Purge Unit
Front Covers & Rear Covers
Upper Roll Unit, Suction Fan & Waste Ink Unit
Platen & Feed Roller
Pinch Roller, Release Lever & Mist Fan
Lower Roll Unit (Right)
ROLL UNIT MAIN (OPTION)
Roll Covers
Top Covers & Side Covers
Детали Ink Tank
| Деталь: | PRINT HEAD |
| Парткод: | NPN |
| Деталь: | INK TANK (Y) |
| Парткод: | NPN |
| Деталь: | INK TANK (M) |
| Парткод: | NPN |
| Деталь: | INK TANK (C) |
| Парткод: | NPN |
| Деталь: | INK TANK (PC) |
| Парткод: | NPN |
| Деталь: | INK TANK (PM) |
| Парткод: | NPN |
| Деталь: | INK TANK (GY) |
| Парткод: | NPN |
| Деталь: | INK TANK (PBK) |
| Парткод: | NPN |
| Деталь: | INK TANK (MBK) |
| Парткод: | NPN |
| Деталь: | INK TANK (PGY) |
| Парткод: | NPN |
| Деталь: | INK TANK (R) |
| Парткод: | NPN |
| Деталь: | INK TANK (CO) |
| Парткод: | NPN |
| Деталь: | INK TANK (B) |
| Парткод: | NPN |
| Деталь: | HOLD PIN4 |
| Парткод: | QC4-9195-000 |
| Деталь: | LOCK BELT |
| Парткод: | QD1-2645-000 |
| Деталь: | HOLDER, SPOOL BEARING L |
| Парткод: | QD1-2704-000 |
| Деталь: | HOLDER, SPOOL BEARING R |
| Парткод: | QD1-2705-000 |
| Деталь: | GEAR, SPOOL |
| Парткод: | QD1-2706-000 |
| Деталь: | PLATEN CLEANER BRUSH |
| Парткод: | QD1-2729-000 |
| Деталь: | PIN, SPOOL |
| Парткод: | QD1-2747-000 |
| Деталь: | SPOOL SHAFT UNIT |
| Парткод: | QM4-4304-000 |
| Деталь: | SPOOL 3INCH ATTACHMENT UNIT |
| Парткод: | QM4-4296-000 |
| Деталь: | SPOOL FLANGE UNIT L |
| Парткод: | QM4-4297-000 |
| Деталь: | SPOOL FLANGE UNIT R |
| Парткод: | QM4-4298-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | RETAINING RING (E-TYPE) |
| Парткод: | XD2-1100-322 |
| Деталь: | RING, E |
| Парткод: | XD2-1100-642 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-182 |
| Деталь: | BEARING |
| Парткод: | XG9-0793-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK2-1739-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK2-1741-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK2-1743-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK2-1745-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK2-1747-000 |
| Деталь: | CORD, POWER |
| Парткод: | QK2-1749-000 |
| Деталь: | CORD, GROUNDING |
| Парткод: | QK2-0830-000 |
| Деталь: | HEXAGONAL WRENCH |
| Парткод: | QD1-2746-000 |
| Деталь: | WRENCH, HEX KEY |
| Парткод: | QC2-4362-000 |
| Деталь: | HOLDER, REAR ROD |
| Парткод: | QD1-2522-000 |
| Деталь: | BOX |
| Парткод: | QD1-2736-000 |
| Деталь: | CAP, STAND |
| Парткод: | QD1-2787-000 |
| Деталь: | PLATE, CASTER |
| Парткод: | QD1-2879-000 |
| Деталь: | CASTER, W/LOCK |
| Парткод: | QD1-2880-000 |
| Деталь: | SIDE ROD UNIT |
| Парткод: | QM4-4294-020 |
| Деталь: | REAR ROD UNIT |
| Парткод: | QM4-4355-000 |
| Деталь: | TOP ROD UNIT |
| Парткод: | QM4-4358-010 |
| Деталь: | SCREW, RS, M4X10 |
| Парткод: | XA9-0949-000 |
| Деталь: | SCREW, HEX SOCKET M4X10 |
| Парткод: | QC4-9300-000 |
| Деталь: | BOLT, HEXAGON BUTTON, M4X30 |
| Парткод: | QC4-9303-000 |
| Деталь: | SCREW, MACHINE M8X16 |
| Парткод: | XB7-1080-169 |
| Деталь: | CAP SUPPORT, TOP ROD L |
| Парткод: | QD1-2740-000 |
| Деталь: | CAP, TOP ROD L |
| Парткод: | QD1-2521-010 |
| Деталь: | BASKET ROLL UNIT |
| Парткод: | QM4-8680-010 |
| Деталь: | ROD JOINT |
| Парткод: | QD1-2529-000 |
| Деталь: | ROD END |
| Парткод: | QD1-2528-000 |
| Деталь: | PTATE, LOCK |
| Парткод: | QC5-8788-000 |
| Деталь: | ARM, LEVER LINK |
| Парткод: | QC5-1874-000 |
| Деталь: | SIX-RING RUBBER CHAIN |
| Парткод: | QC5-1900-000 |
| Деталь: | HOLDER, CARRIAGE UNIT |
| Парткод: | QD1-1958-000 |
| Деталь: | SHEET DAMPER |
| Парткод: | QD1-2533-000 |
| Деталь: | BELT, CARRIAGE |
| Парткод: | QD1-2176-000 |
| Деталь: | FILM, TIMING SLIT STRIP |
| Парткод: | QD1-2179-000 |
| Деталь: | SPRING, FILM STRIP |
| Парткод: | QD1-2420-000 |
| Деталь: | MOTOR, DC, 47.8W |
| Парткод: | QK1-2868-000 |
| Деталь: | MULTI SENSOR UNIT |
| Парткод: | QM4-4341-000 |
| Деталь: | FLEXIBLE CABLE UNIT |
| Парткод: | QM4-4361-000 |
| Деталь: | BUSHING / CLEANER KIT |
| Парткод: | QM4-4362-000 |
| Деталь: | CARRIAGE ENCODER UNIT |
| Парткод: | QM4-4363-000 |
| Деталь: | TUBE UNIT |
| Парткод: | QM4-5544-000 |
| Деталь: | CARRIAGE UNIT |
| Парткод: | QM4-8639-000 |
| Деталь: | INK TUBE UNIT |
| Парткод: | QM4-5543-000 |
| Деталь: | CARRIAGE RELAY PCB UNIT |
| Парткод: | QM7-4815-000 |
| Деталь: | SCREW, TP, M3 PAN HEAD, M2.6X8 |
| Парткод: | QU1-9070-000 |
| Деталь: | SCREW, MACH, TRUSS HEAD, M3X20 |
| Парткод: | XB1-2302-005 |
| Деталь: | SCREW, CROSS-RECESS, FCH |
| Парткод: | XB1-2400-607 |
| Деталь: | SCREW, TP, BH3X8, S |
| Парткод: | XB4-7300-805 |
| Деталь: | SCREW, TP, M3X12 |
| Парткод: | XB4-7301-209 |
| Деталь: | COUPLING, CARRIAGE |
| Парткод: | QD1-1934-000 |
| Деталь: | JOINT LEVER UNIT |
| Парткод: | QM4-4912-000 |
| Деталь: | LEVER, HEAD SET |
| Парткод: | QC5-1836-000 |
| Деталь: | SPRING, HEAD SET LEVER |
| Парткод: | QC3-4923-000 |
| Деталь: | STOPPER, BELT, CR |
| Парткод: | QD1-1951-000 |
| Деталь: | SPRING, SLIDER PRESSURE, CR |
| Парткод: | QD1-2111-000 |
| Деталь: | HOLDER, SLIDER PRESSURE, CR |
| Парткод: | QD1-2110-000 |
| Деталь: | STOPPER, SUB SLIDER, CR |
| Парткод: | QD1-1963-000 |
| Деталь: | HOLDER, BELT, CR |
| Парткод: | QD1-2545-000 |
| Деталь: | SPRING, IDLER PULLEY |
| Парткод: | QD1-1983-000 |
| Деталь: | TENSIONER, IDLER PULLEY |
| Парткод: | QD1-1981-000 |
| Деталь: | SLIDER, IDLER PULLEY |
| Парткод: | QD1-1982-000 |
| Деталь: | IDLER PULLEY UNIT |
| Парткод: | QM4-4191-000 |
| Деталь: | SCREW, W/SPRING WASHER, M4X8 |
| Парткод: | XB2-8400-805 |
| Деталь: | CUT WASHER |
| Парткод: | QD1-1441-000 |
| Деталь: | COVER, HOME POSITION |
| Парткод: | QD1-2221-000 |
| Деталь: | COVER, BACK POSITION |
| Парткод: | QD1-2222-000 |
| Деталь: | LOCK LEVER, ACCESS COVER L |
| Парткод: | QD1-2408-000 |
| Деталь: | SPRING, LOCK |
| Парткод: | QD1-2411-000 |
| Деталь: | PLATE, SPRING SWITCH |
| Парткод: | QD1-2416-000 |
| Деталь: | HOLDER, SWITCH |
| Парткод: | QD1-2548-000 |
| Деталь: | SOLENOID |
| Парткод: | QK2-1484-000 |
| Деталь: | ACCESS COVER LOCK UNIT R |
| Парткод: | QM4-4217-000 |
| Деталь: | CUTTER BLADE UNIT |
| Парткод: | QM4-4906-000 |
| Деталь: | CUTTER MOTOR UNIT, W/ENCODER |
| Парткод: | QM4-8677-000 |
| Деталь: | HARNESS ASSY, INTERLOCK SW |
| Парткод: | QM7-4831-000 |
| Деталь: | HARNESS ASSY, RSIDE FRONT |
| Парткод: | QM7-4832-000 |
| Деталь: | MICROSWITCH |
| Парткод: | WC4-5171-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, MACH, TRUSS HEAD, M3X20 |
| Парткод: | XB1-2302-005 |
| Деталь: | SCREW, FLANGED PAN HEAD, M3X4 |
| Парткод: | XB6-7300-405 |
| Деталь: | CUT WASHER |
| Парткод: | QD1-1441-000 |
| Деталь: | COVER, ROLL GEAR L |
| Парткод: | QD1-1792-000 |
| Деталь: | HOLDER, SPOOL L |
| Парткод: | QD1-1795-000 |
| Деталь: | COVER, SIDE L SUB |
| Парткод: | QD1-2656-000 |
| Деталь: | COVER, SIDE TOP L |
| Парткод: | QD1-2784-000 |
| Деталь: | CAP, COVER SIDE L |
| Парткод: | QD1-2853-000 |
| Деталь: | CABLE, ROLL UNIT |
| Парткод: | QK2-1476-000 |
| Деталь: | HANDLE UNIT, LOWER SUPPORT L |
| Парткод: | QM4-4897-000 |
| Деталь: | I/F PCB UNIT, RU |
| Парткод: | QM4-4231-000 |
| Деталь: | SPOOL LOCK UNIT |
| Парткод: | QM4-4299-000 |
| Деталь: | COVER UNIT, SIDE OUTER L |
| Парткод: | QM4-4382-000 |
| Деталь: | ACTIVE ROLL BRAKE UNIT |
| Парткод: | QM4-8678-000 |
| Деталь: | HARNESS ASSY, LO SPL SOL |
| Парткод: | QM7-4871-000 |
| Деталь: | HARNESS ASSY, ARB MOTOR |
| Парткод: | QM7-4872-000 |
| Деталь: | HARNESS ASSY, LO SPLSET L |
| Парткод: | QM7-4873-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | I/F PCB UNIT |
| Парткод: | QM4-4368-000 |
| Деталь: | POWER SUPPLY UNIT |
| Парткод: | QM4-5548-000 |
| Деталь: | MAIN PCB UNIT |
| Парткод: | QM4-5547-000 |
| Деталь: | BACKUP PCB UNIT |
| Парткод: | QM7-4756-000 |
| Деталь: | HARNESS ASSY, R |
| Парткод: | QM7-4848-000 |
| Деталь: | HARNESS ASSY, L |
| Парткод: | QM7-4865-000 |
| Деталь: | HDD, ST320LT012 |
| Парткод: | WM2-5295-000 |
| Деталь: | SENSOR, HUMIDITY |
| Парткод: | WP2-5410-000 |
| Деталь: | WIRELESS LAN PCB UNIT |
| Парткод: | QM4-4865-000 |
| Деталь: | RELAY PCB UNIT, RU |
| Парткод: | QM4-4867-000 |
| Деталь: | HDD CABLE ASSY |
| Парткод: | QK2-1472-000 |
| Деталь: | HARNESS ASSY, POWER SUPPLY |
| Парткод: | QM7-4821-000 |
| Деталь: | HARNESS ASSY, INLET RELAY |
| Парткод: | QM7-4886-000 |
| Деталь: | INLET HARNESS UNIT |
| Парткод: | QM7-4825-000 |
| Деталь: | HARNESS ASSY, RU RELAY |
| Парткод: | QM7-4891-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, CROSS-RECESS, FCH |
| Парткод: | XB1-2400-607 |
| Деталь: | SCREW, TP, BH3X8, S |
| Парткод: | XB4-7300-805 |
| Деталь: | SCREW, TP, M3X6 (S) |
| Парткод: | XB6-7300-605 |
| Деталь: | SCREW, FLANGED PAN HEAD, M4X8 |
| Парткод: | XB6-7400-805 |
| Деталь: | WASHER, TOOTHED LOCK, M4 |
| Парткод: | XD1-4200-402 |
| Деталь: | SCREW, TOOTHED WASHER, M4X6 |
| Парткод: | XB2-7400-607 |
| Деталь: | PLATE, PURGE CHECK |
| Парткод: | AY3-4607-000 |
| Деталь: | GREASE, FLOIL G-31KB |
| Парткод: | AY3-4609-000 |
| Деталь: | TUBE, WASTE INK |
| Парткод: | AY3-4595-000 |
| Деталь: | W-INK TUBE, BLACK |
| Парткод: | AY3-4530-000 |
| Деталь: | SYRINGE |
| Парткод: | CK-0541-000 |
| Деталь: | STOPPER |
| Парткод: | QC2-6710-000 |
| Деталь: | TOOL, CUTTER SPACER |
| Парткод: | QD1-2904-000 |
| Деталь: | ABSORBER, CAP |
| Парткод: | QC5-1993-000 |
| Деталь: | ABSORBER, INK |
| Парткод: | QD1-2348-000 |
| Деталь: | UPPER GUIDE, INK TANK |
| Парткод: | QD1-2579-000 |
| Деталь: | HEAD MANAGEMENT SENSOR UNIT |
| Парткод: | QM4-4038-000 |
| Деталь: | INK SUPPLY MOUNT UNIT L |
| Парткод: | QM4-4197-000 |
| Деталь: | INK SUPPLY MOUNT UNIT R |
| Парткод: | QM4-4198-000 |
| Деталь: | WASTE INK TANK UNIT |
| Парткод: | QM4-4226-000 |
| Деталь: | ROM BOARD UNIT |
| Парткод: | QM4-4287-000 |
| Деталь: | INK SUPPLY TANK HOLDER UNIT L |
| Парткод: | QM4-4316-020 |
| Деталь: | INK SUPPLY TANK HOLDER UNIT R |
| Парткод: | QM4-4318-020 |
| Деталь: | PURGE UNIT |
| Парткод: | QM4-4352-000 |
| Деталь: | SUB INK TANK UNIT L |
| Парткод: | QM4-8640-000 |
| Деталь: | SUB INK TANK UNIT R |
| Парткод: | QM4-8641-000 |
| Деталь: | LIFT UNIT |
| Парткод: | QM4-8710-000 |
| Деталь: | TANK LED PCB UNIT |
| Парткод: | QM7-4761-000 |
| Деталь: | HARNESS ASSY, TANKLED R RLY |
| Парткод: | QM7-4834-000 |
| Деталь: | HARNESS ASSY, TANKLED L RLY |
| Парткод: | QM7-4835-000 |
| Деталь: | HARNESS ASSY, HEAD MANAGEMENT |
| Парткод: | QM7-4845-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, TP, BH3X8, S |
| Парткод: | XB4-7300-805 |
| Деталь: | LEVER, INK TANK |
| Парткод: | QD1-2326-010 |
| Деталь: | HANDLE UNIT, INK TANK S |
| Парткод: | QM4-4923-010 |
| Деталь: | COVER, INKTANK BACK |
| Парткод: | QD1-2317-000 |
| Деталь: | COVER, INKTANK R INSIDE |
| Парткод: | QD1-2320-000 |
| Деталь: | COVER, INKTANK L INSIDE |
| Парткод: | QD1-2345-000 |
| Деталь: | COVER, MIST FAN |
| Парткод: | QD1-2349-000 |
| Деталь: | COVER, FRONT R |
| Парткод: | QD1-2359-000 |
| Деталь: | COVER, FRONT L |
| Парткод: | QD1-2367-000 |
| Деталь: | HANDLE, INKTANK BACK |
| Парткод: | QD1-2553-000 |
| Деталь: | COVER, INKTANK TOP BACK |
| Парткод: | QD1-2562-000 |
| Деталь: | PRODUCT NAME PLATE |
| Парткод: | QC5-7997-000 |
| Деталь: | PRODUCT NAME PLATE |
| Парткод: | QC5-7998-000 |
| Деталь: | INK SUPPLY MOUNT BASE UNIT L |
| Парткод: | QM4-8696-000 |
| Деталь: | INK SUPPLY MOUNT BASE UNIT R |
| Парткод: | QM4-8697-000 |
| Деталь: | COVER UNIT, INKTANK, TOP L |
| Парткод: | QM4-8701-010 |
| Деталь: | COVER UNIT, INKTANK, TOP R |
| Парткод: | QM4-8702-010 |
| Деталь: | COVER UNIT, MTC |
| Парткод: | QM4-4899-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, TP, BH3X8, S |
| Парткод: | XB4-7300-805 |
| Деталь: | SCREW, TP, TRUSS HEAD, M4X10 |
| Парткод: | XB4-7401-005 |
| Деталь: | SCREW, TP, M3X8 |
| Парткод: | XA9-1648-000 |
| Деталь: | COVER, BACK |
| Парткод: | QD1-2567-000 |
| Деталь: | COVER, BACK RIGHT |
| Парткод: | QD1-2695-000 |
| Деталь: | COVER, BACK LEFT |
| Парткод: | QD1-2696-000 |
| Деталь: | SPRING, PAPER SET |
| Парткод: | QD1-1677-000 |
| Деталь: | LEVER, PAPER FEED SENSOR |
| Парткод: | QD1-2159-000 |
| Деталь: | SPRING, PAPER FEED SENSOR |
| Парткод: | QD1-2160-000 |
| Деталь: | NIP ARM UNIT |
| Парткод: | QM4-4926-000 |
| Деталь: | WASTE INK ABSORBER UNIT A |
| Парткод: | QM4-4241-000 |
| Деталь: | WASTE INK ABSORBER UNIT B |
| Парткод: | QM4-4242-000 |
| Деталь: | ROLL PAPER FEED SENSOR UNIT |
| Парткод: | QM4-4249-000 |
| Деталь: | SUCTION FAN UNIT |
| Парткод: | QM4-4260-000 |
| Деталь: | SUCTION FAN DUCT UNIT |
| Парткод: | QM4-4261-000 |
| Деталь: | CAM SHAFT UNIT |
| Парткод: | QM4-4291-000 |
| Деталь: | WASTE INK ABSORBER UNIT |
| Парткод: | QM4-4345-000 |
| Деталь: | ACTIVE ROLL BRAKE UNIT |
| Парткод: | QM4-8678-000 |
| Деталь: | DRIVE NIP ARM UNIT |
| Парткод: | QM4-8715-000 |
| Деталь: | FLAPPER SEPARATE UNIT |
| Парткод: | QM4-8718-000 |
| Деталь: | GUIDE UNIT, LOW A |
| Парткод: | QM4-4927-000 |
| Деталь: | GUIDE UNIT, LOW B |
| Парткод: | QM4-4928-000 |
| Деталь: | GUIDE UNIT, OUTSIDE A |
| Парткод: | QM4-4924-000 |
| Деталь: | GUIDE UNIT, OUTSIDE C |
| Парткод: | QM4-8730-000 |
| Деталь: | HARNESS ASSY, UP RLNIP RELAY |
| Парткод: | QM7-4858-000 |
| Деталь: | HARNESS ASSY, ARB MOTOR |
| Парткод: | QM7-4872-000 |
| Деталь: | HARNESS ASSY, RLNIP PF SNS |
| Парткод: | QM7-4884-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, FLANGED PAN HEAD, M4X8 |
| Парткод: | XB6-7400-805 |
| Деталь: | WASTE INK ABSORBER UNIT C |
| Парткод: | QM4-4243-000 |
| Деталь: | GUIDE UNIT, LOW C |
| Парткод: | QM4-4929-000 |
| Деталь: | GUIDE UNIT, LOW D |
| Парткод: | QM4-4930-000 |
| Деталь: | WASTE INK ABSORBER UNIT D |
| Парткод: | QM4-4244-000 |
| Деталь: | GUIDE UNIT, LOW E |
| Парткод: | QM4-4931-000 |
| Деталь: | BELT, PAPER TRANSPORT |
| Парткод: | QC4-8783-000 |
| Деталь: | FLANGE, PULLEY |
| Парткод: | QC4-8784-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | QC5-8099-000 |
| Деталь: | PLATEN, REAR |
| Парткод: | QD1-1758-000 |
| Деталь: | AWAY PLATEN |
| Парткод: | QD1-1760-000 |
| Деталь: | PLATEN, INK PRE EJECTION |
| Парткод: | QD1-1761-000 |
| Деталь: | HOLDER, PAPER FEED ROLLER |
| Парткод: | QD1-2079-000 |
| Деталь: | PLATEN, UNDER A |
| Парткод: | QD1-2244-000 |
| Деталь: | FILM, TIMING SLIT DISK |
| Парткод: | QD1-2702-000 |
| Деталь: | PLATEN, UNDER HOME |
| Парткод: | QD1-2801-000 |
| Деталь: | PAPER FEED ROLLER UNIT |
| Парткод: | QM4-6309-000 |
| Деталь: | CODEWHEEL COVER UNIT |
| Парткод: | QM4-5388-000 |
| Деталь: | PAPER FEED MOTOR UNIT |
| Парткод: | QM4-5389-000 |
| Деталь: | PLATEN UNIT, TOP A |
| Парткод: | QM4-4269-000 |
| Деталь: | PLATEN UNIT, TOP AWAY |
| Парткод: | QM4-4270-000 |
| Деталь: | PLATEN UNIT, TOP B |
| Парткод: | QM4-4272-000 |
| Деталь: | PRE PRINTING PLATEN BASE ASSY |
| Парткод: | QM4-4277-000 |
| Деталь: | PAPER FEED ENCODER UNIT |
| Парткод: | QM4-4288-000 |
| Деталь: | HARNESS ASSY, LFPE SNS |
| Парткод: | QM7-4828-000 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | WG8-5677-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1161-000 |
| Деталь: | SCREW, W/SPRING WASHER, M4X8 |
| Парткод: | XB2-8400-805 |
| Деталь: | PLATEN UNIT, TOP C |
| Парткод: | QM4-4273-000 |
| Деталь: | PLATEN UNIT, TOP D |
| Парткод: | QM4-4274-000 |
| Деталь: | CUT WASHER |
| Парткод: | QD1-1441-000 |
| Деталь: | PLATEN, REAR LS |
| Парткод: | QD1-1759-000 |
| Деталь: | PLATEN, UNDER B |
| Парткод: | QD1-2245-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | QD1-2270-000 |
| Деталь: | DRIVE UNIT, PLATEN SHUTTER |
| Парткод: | QM4-4265-000 |
| Деталь: | SHAFT UNIT, PLATEN SHUTTER |
| Парткод: | QM4-4266-000 |
| Деталь: | PLATEN SHUTTER UNIT 1 |
| Парткод: | QM4-4267-000 |
| Деталь: | PLATEN SHUTTER UNIT 2 |
| Парткод: | QM4-4268-000 |
| Деталь: | PLATEN UNIT, TOP E |
| Парткод: | QM4-4275-000 |
| Деталь: | PLATEN UNIT, TOP F |
| Парткод: | QM4-4276-000 |
| Деталь: | HARNESS ASSY, P STAY RELAY |
| Парткод: | QM7-4862-000 |
| Деталь: | HARNESS ASSY, P STAY PS MOT |
| Парткод: | QM7-4887-000 |
| Деталь: | HARNESS ASSY, P STAY PS SNS |
| Парткод: | QM7-4888-000 |
| Деталь: | HARNESS ASSY, P STAY HP SNS |
| Парткод: | QM7-4889-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | E RING G17 |
| Парткод: | QC4-1522-000 |
| Деталь: | BUSH, ARM ROTARY SHAFT |
| Парткод: | QD1-2085-000 |
| Деталь: | BUSHING, PRESSURE RELEASE |
| Парткод: | QD1-2231-000 |
| Деталь: | GEAR, PRESSURE RELEASE |
| Парткод: | QD1-2233-000 |
| Деталь: | GEAR, RELEASE LEVER |
| Парткод: | QD1-2237-000 |
| Деталь: | PAD, RELEASE LEVER STOPPER |
| Парткод: | QD1-2280-000 |
| Деталь: | SPRING, RELEASE LEVER |
| Парткод: | QD1-2712-000 |
| Деталь: | BUSHING, PR RELEASE |
| Парткод: | QD1-2884-000 |
| Деталь: | RELEASE LEVER UNIT |
| Парткод: | QM4-4208-000 |
| Деталь: | MIST FAN DUCT UNIT 2 |
| Парткод: | QM4-4227-000 |
| Деталь: | PINCH ROLLER UNIT |
| Парткод: | QM4-4252-000 |
| Деталь: | PINCH ROLLER UNIT L |
| Парткод: | QM4-4254-000 |
| Деталь: | SHAFT PRESSURE RELEASE UNIT |
| Парткод: | QM4-4864-000 |
| Деталь: | HARNESS ASSY, TANK CVR MFAN R |
| Парткод: | QM7-4829-000 |
| Деталь: | HARNESS ASSY, TANK CVR MFAN L |
| Парткод: | QM7-4850-000 |
| Деталь: | DETECT MICRO SWITCH |
| Парткод: | WC4-5376-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, FLANGED PAN HEAD, M4X8 |
| Парткод: | XB6-7400-805 |
| Деталь: | CUT WASHER |
| Парткод: | QD1-1441-000 |
| Деталь: | BUSHING, DRIVE |
| Парткод: | QD1-1443-000 |
| Деталь: | SPRING, LOCK A |
| Парткод: | QD1-1785-000 |
| Деталь: | SPRING, LOCK C |
| Парткод: | QD1-1787-000 |
| Деталь: | ROLLER, LOCK |
| Парткод: | QD1-1788-000 |
| Деталь: | LOCK LEVER A |
| Парткод: | QD1-1789-000 |
| Деталь: | LOCK LEVER B |
| Парткод: | QD1-1790-000 |
| Деталь: | HOLDER, SPOOL R |
| Парткод: | QD1-1791-000 |
| Деталь: | KNOB, OPERATION |
| Парткод: | QD1-2588-000 |
| Деталь: | PLATE, SPOOL GROUND |
| Парткод: | QD1-2593-000 |
| Деталь: | COVER, SIDE R REAR |
| Парткод: | QD1-2725-000 |
| Деталь: | COVER, SIDE R |
| Парткод: | QD1-2726-000 |
| Деталь: | HANDLE UNIT, LOWER SUPPORT R |
| Парткод: | QM4-4898-000 |
| Деталь: | OPERATION PANEL UNIT, RU |
| Парткод: | QM4-4914-000 |
| Деталь: | COVER UNIT, SIDE OUTER R |
| Парткод: | QM4-4915-000 |
| Деталь: | HARNESS ASSY, RU PANEL RLY |
| Парткод: | QM7-4877-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | RETAINING RING (E-TYPE) |
| Парткод: | XD2-1100-322 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, TP, BH3X8, S |
| Парткод: | XB4-7300-805 |
| Деталь: | LEVER ASSY, SPL LOCK R |
| Парткод: | QL2-8481-000 |
| Деталь: | SPRING, PAPER SET |
| Парткод: | QD1-1677-000 |
| Деталь: | GUIDE, UPPER |
| Парткод: | QD1-1781-000 |
| Деталь: | LEVER, PAPER FEED SENSOR |
| Парткод: | QD1-2159-000 |
| Деталь: | SPRING, PAPER FEED SENSOR |
| Парткод: | QD1-2160-000 |
| Деталь: | CAM, FLAP SELEC |
| Парткод: | QD1-2595-000 |
| Деталь: | SUPPORT, FLAP SELEC |
| Парткод: | QD1-2602-000 |
| Деталь: | NIP ARM UNIT |
| Парткод: | QM4-4926-000 |
| Деталь: | ROLL PAPER FEED SENSOR UNIT |
| Парткод: | QM4-4249-000 |
| Деталь: | CAM SHAFT UNIT |
| Парткод: | QM4-4291-000 |
| Деталь: | RAIL UNIT L |
| Парткод: | QM4-4342-000 |
| Деталь: | RAIL UNIT R |
| Парткод: | QM4-4343-000 |
| Деталь: | PAPER GUIDE ROLLER UNIT, RU A |
| Парткод: | QM4-4859-000 |
| Деталь: | PAPER GUIDE ROLLER UNIT, RU B |
| Парткод: | QM4-4860-000 |
| Деталь: | DRIVE NIP ARM UNIT |
| Парткод: | QM4-8715-000 |
| Деталь: | FLAPPER SEPARATE UNIT |
| Парткод: | QM4-8718-000 |
| Деталь: | GUIDE UNIT, LOW A |
| Парткод: | QM4-4927-000 |
| Деталь: | GUIDE UNIT, LOW B |
| Парткод: | QM4-4928-000 |
| Деталь: | HARNESS ASSY, LO FLAP SPLSET |
| Парткод: | QM7-4876-000 |
| Деталь: | HARNESS ASSY, RU MAIN |
| Парткод: | QM7-4880-000 |
| Деталь: | HARNESS ASSY, RLNIP PF SNS |
| Парткод: | QM7-4884-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, HEX SOCKET M4X10 |
| Парткод: | QC4-9300-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, TP, M3X6 (S) |
| Парткод: | XB6-7300-605 |
| Деталь: | SCREW, MACHINE M8X16 |
| Парткод: | XB7-1080-169 |
| Деталь: | PAPER GUIDE ROLLER UNIT, RU C |
| Парткод: | QM4-4861-000 |
| Деталь: | GUIDE UNIT, LOW C |
| Парткод: | QM4-4929-000 |
| Деталь: | GUIDE UNIT, LOW D |
| Парткод: | QM4-4930-000 |
| Деталь: | PAPER GUIDE ROLLER UNIT, RU D |
| Парткод: | QM4-4862-000 |
| Деталь: | GUIDE UNIT, LOW E |
| Парткод: | QM4-4931-000 |
| Деталь: | CUT WASHER |
| Парткод: | QD1-1441-000 |
| Деталь: | HOLDER, SPOOL SIDE R |
| Парткод: | QD1-1721-010 |
| Деталь: | HOLDER, SPOOL SIDE L |
| Парткод: | QD1-1722-000 |
| Деталь: | COVER, SPOOL R |
| Парткод: | QD1-1723-000 |
| Деталь: | COVER, ROLL GEAR L |
| Парткод: | QD1-1792-000 |
| Деталь: | CASE, SPOOL SIDE INNER R |
| Парткод: | QD1-2239-000 |
| Деталь: | SPRING, SPOOL COVER |
| Парткод: | QD1-2240-000 |
| Деталь: | COVER, SPOOL L |
| Парткод: | QD1-2241-000 |
| Деталь: | PAD, RELEASE LEVER STOPPER |
| Парткод: | QD1-2280-000 |
| Деталь: | COVER, ROLL TOP |
| Парткод: | QD1-2428-000 |
| Деталь: | COVER, ROLL SIDE L |
| Парткод: | QD1-2436-000 |
| Деталь: | COVER, ROLL SIDE R |
| Парткод: | QD1-2431-000 |
| Деталь: | PAD, EJECT FRICTION |
| Парткод: | QD1-2435-000 |
| Деталь: | COVER, ROLL FRONT |
| Парткод: | QD1-2652-000 |
| Деталь: | CAP, ROLL COVER SHAFT |
| Парткод: | QD1-2709-000 |
| Деталь: | SPRING, EJECT EARTH |
| Парткод: | QD1-2710-000 |
| Деталь: | CAM, ROLL COVER SIDE |
| Парткод: | QD1-2863-000 |
| Деталь: | CATCH, ROLL COVER |
| Парткод: | QD1-2867-000 |
| Деталь: | SPRING, EARTH |
| Парткод: | QD1-2888-000 |
| Деталь: | SPOOL LOCK UNIT |
| Парткод: | QM4-4299-000 |
| Деталь: | SPOOL SENSOR UNIT |
| Парткод: | QM4-4301-000 |
| Деталь: | PLATE UNIT, SPOOL SIDE SUPPORT |
| Парткод: | QM4-4907-000 |
| Деталь: | BUSH, ROLL COVER L |
| Парткод: | QD1-2866-000 |
| Деталь: | DAMPER UNIT, ROLL COVER R |
| Парткод: | QM4-4909-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, TP, WASHER HEAD, M3X12 |
| Парткод: | XA9-1752-000 |
| Деталь: | SCREW, TP, BH3X8, S |
| Парткод: | XB4-7300-805 |
| Деталь: | SCREW, TP, TRUSS HEAD, M4X10 |
| Парткод: | XB4-7401-005 |
| Деталь: | SCREW, FLANGED PAN HEAD, M3X4 |
| Парткод: | XB6-7300-405 |
| Деталь: | SCREW, TP, M3X6 (S) |
| Парткод: | XB6-7300-605 |
| Деталь: | SCREW, FLANGED PAN HEAD, M4X8 |
| Парткод: | XB6-7400-805 |
| Деталь: | COVER, ROLL BACK UP |
| Парткод: | QD1-2718-000 |
| Деталь: | ROLLER, PRESS |
| Парткод: | QD1-1358-000 |
| Деталь: | SHAFT, PRESS ROLLER |
| Парткод: | QD1-1359-000 |
| Деталь: | ROTARY DAMPER |
| Парткод: | QD1-2912-000 |
| Деталь: | COVER, SIDE R A |
| Парткод: | QD1-2358-000 |
| Деталь: | COVER, FRONT TOP R |
| Парткод: | QD1-2360-000 |
| Деталь: | COVER, SIDE L A |
| Парткод: | QD1-2366-000 |
| Деталь: | WINDOW |
| Парткод: | QD1-2397-000 |
| Деталь: | CAP, SIDE COVER |
| Парткод: | QD1-2752-000 |
| Деталь: | WINDOW R |
| Парткод: | QD1-2892-000 |
| Деталь: | CABLE, USB RELAY |
| Парткод: | QK2-1482-000 |
| Деталь: | OPERATION PANEL UNIT |
| Парткод: | QM4-4245-000 |
| Деталь: | GUARD ACCESS COVER UNIT W/SPUR |
| Парткод: | QM4-4350-000 |
| Деталь: | COVER UNIT, TOP L |
| Парткод: | QM4-4383-000 |
| Деталь: | COVER UNIT, SIDE R B |
| Парткод: | QM4-4900-000 |
| Деталь: | COVER UNIT, SIDE L B |
| Парткод: | QM4-4901-000 |
| Деталь: | USB HOST PCB ASSY |
| Парткод: | QM7-4757-000 |
| Деталь: | HARNESS ASSY, PANEL LVDS |
| Парткод: | QM7-4870-000 |
| Деталь: | ACCESS COVER UNIT S |
| Парткод: | QM4-5546-000 |
| Деталь: | COVER UNIT, BACK TOP CENTER |
| Парткод: | QM4-8694-000 |
| Деталь: | COVER UNIT, BACK TOP R |
| Парткод: | QM4-8695-000 |
| Деталь: | SCREW, RS, M4 |
| Парткод: | XA9-0732-000 |
| Деталь: | SCREW, TAPPING, C.S.HEAD M4X10 |
| Парткод: | XA9-1157-000 |
| Деталь: | SCREW, TP, TRUSS HEAD, M4X10 |
| Парткод: | XB4-7401-005 |
| Деталь: | SCREW, FLANGED PAN HEAD, M3X4 |
| Парткод: | XB6-7300-405 |
| Деталь: | SPRING, ACCESS COVER |
| Парткод: | QD1-2558-000 |
| Деталь: | HINGE ASSY, ACCESS COVER SP |
| Парткод: | QL2-8518-000 |
| Деталь: | LEVER, LOCK L |
| Парткод: | QD1-2549-000 |
| Деталь: | LEVER, LOCK R |
| Парткод: | QD1-2550-000 |
Коды ошибок
E000-000
E001-0001
E001-0002
E001-0003
E002-0000
E003-0000
E004-0000
E005-0000
E010-0000
E012-0000
E013-0000
E014-0000
E020-0000
E032-0001
E061-0001
E061-0002
E100-0001
E100-0002
E110-0001
E121-0001
E196
E202-0001
E202-0002
E204-0001
E220-0001
E225-0000
E225-0002
E240-0000
E240-010B
E243-0000
E248-0001
E248-0002
E248-0003
E302-0001
E302-0002
E315-0007
E315-0010
E412-0001
E420-0001
E421-0001
E422-0001
E500-0001
E503-0002
E504-0001
E504-0002
E504-0003
E504-0004
E505-0001
E505-0002
E512-0001
E512-0002
E530-0001
E530-0002
E531-0001
E531-0002
E532-0001
E532-0002
E535-0001
E535-0002
E535-0003
E584-0001
E584-0002
E584-0003
E590-0001
E590-0002
E593-0001
E593-0002
E5F0-0001
E5F0-0002
E5F1-0001
E5F1-0002
E5F2-0001
E5F2-0002
E5F3-0001
E5F3-0002
E5F4-0001
E5F4-0002
E5F5-0001
E5F5-0002
E5F6-0001
E5F6-0002
E5F6-0003
E5F6-0004
E5F6-0005
E5F8-0001
E5F8-0002
E5F8-0003
E5F9-0001
E5F9-0002
E5F9-0003
E601-0000
E601-0001
E602-0001
E602-0002
E602-0003
E602-0004
E607-0000
E677-0001
E710-0001
E710-0002
E710-0003
E711-0001
E711-0002
E711-0003
E712-0001
E712-0002
E713-0000
E717-0001
E719-0001
E732-0001
E732-9999
E733-0001
E740-0001
E740-0002
E740-0003
E741-0000
E743-0000
E744-0001
E744-0002
E744-0003
E744-0004
E744-1000
E744-2000
E804-0000
E805-0001
E805-0002
E824-0000
Описание
| Error code: | E000-000 |
| Description: | The main thermistor (TH1) has poor contact or an open circuit. The thermal switch (TP1) has an open circuit. The fixing heater has an open circuit. The AC driver is faulty. The DC controller PCB is faulty. After the main power switch is turned on, the temperature detected by the main thermistor does not reach 70°C. The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR). |
| Error code: | E001-0001 |
| Description: | Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control. |
| Causes: | The sub thermistor detected a temperature of higher than 290 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0002 |
| Description: | Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 1 has detected a high temperature (ASIC detection) |
| Causes: | The fixing film unit is faulty (i.e., the thermistor has a short circuit). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service move: COPIER>FUNCTION>CLEAR>ERR. |
| Remedy: | Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E001-0003 |
| Description: | Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 2 has detected a high temperature (ASIC detection) |
| Remedy: | Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E002-0000 |
| Description: | Low temperature during temperature control. The target temperature is not reached during temperature control. |
| Causes: | The fixing film unit is faulty (i.e., the main thermistor TH1 has poor contact, or the fixing heater is faulty). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>FCLEAR>ERR. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0000 |
| Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E004-0000 |
| Description: | Fixing power supply drive circuit error |
| Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
| Error code: | E005-0000 |
| Description: | There is an error in the take-up mechanism of the web. The web of the fixing assembly has been fully taken up. After the web sensor has detected an off state, the count has exceeded 3000. The web length sensor (PS20) is faulty. The DC controller PCB is faulty. |
| Remedy: | Reset in service mode: COPIER>FUNCTION>CLEAR>ERR. If you have replaced the web, reset the reading in the following, and turn off and then on the power: COPIER>COUNTER>DRBL-1>FIX-WEB. |
| Error code: | E010-0000 |
| Description: | Main motor failure The main motor is faulty. |
| Causes: | The main motor (M2) is faulty. the DC controller PCB is faulty. |
| Remedy: | - Check the connector of the main motor. - Replace the main motor. - Replace the DC controller PCB. |
| Error code: | E012-0000 |
| Description: | Error in ITB motor activation. |
| Causes: | The cycle of ITB motor speed detection signal does not move in the specified cycle after ITB motor drive is started. Cause Failure in ITB motor, failure in DC controller PCB |
| Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
| Error code: | E013-0000 |
| Description: | Residual toner feed motor failure |
| Causes: | Residual toner feed motor failure |
| Remedy: | • Check the contact of the connector between the Residual toner feed motor (J89L) and the DC controller PCB (J137). • Replace the Residual toner feed motor |
| Error code: | E014-0000 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor startup error The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E020-0000 |
| Description: | Density sensor failure warning |
| Error code: | E032-0001 |
| Description: | NE controller counter operation failure When the counter function of the NE controller does not work |
| Causes: | The DA unit is faulty. The main controller PCB is faulty. |
| Remedy: | Check the cable connections. |
| Error code: | E061-0001 |
| Description: | At time of potential control, a specific level of potential is absent. Or, the limiter goes on. When forming an image, the potential is 10 V or less during initial rotation. |
| Remedy: | Turn off and then on the main power. |
| Error code: | E061-0002 |
| Description: | At time of potential control, a specific level of potential is absent. Or, the limiter goes on. At time of potential control, the potential is 10 V or less during initial rotation |
| Remedy: | Turn off and then on the main power. |
| Error code: | E100-0001 |
| Description: | Error detection on any of scanner motor, laser unit, and BD detection at scanner area. |
| Causes: | Magenta optical assembly failure |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board. |
| Error code: | E100-0002 |
| Description: | Optical assembly error (Laser) |
| Causes: | Cyan optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0001 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor rotation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E121-0001 |
| Description: | The rotation of the laser cooling fan (1/2) is faulty. The lock signal arrives for 5 sec or more although the laser cooling fan 1 (FM3) is being driven. |
| Remedy: | - Check if there is no foreign material in the rotation assembly of the laser cooling fan 1. - Check if the connector (J503) of the relay PCB is mounted properly. - Replace the laser cooling fan 1. - Replace the DC controller PCB. |
| Error code: | E196 |
| Display: | E196 |
| Description: | DC controller memory failure |
| Causes: | DC controller PCB ROM update failed. |
| Remedy: | 1) Defective DC controller PCB Action: Replace it. |
| Error code: | E202-0001 |
| Description: | Reader HP sensor fault |
| Causes: | Reader HP outward fault The CCD unit moves backward, but does not move to the home position. |
| Remedy: | - Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit. |
| Error code: | E202-0002 |
| Description: | Contact Sensor HP error, Failure in return |
| Causes: | Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
| Error code: | E204-0001 |
| Description: | While an original is being read, the image leading edge signal does not arrive from the ADF |
| Causes: | The ADF controller PCB is faulty. The reader controller PCB is faulty. Caution When this code occurs, no code is indicated, but the keys are locked. The code may be checked in service mode: COPIER>DISPLAY>ERR. |
| Remedy: | 1. Read sensor (S2) Try replacing the read sensor of the ADF. Is the problem corrected? YES: End. 2. ADF controller PCB, Reader controller PCB Try replacing the ADF controller PCB. Is the problem corrected? YES: End. NO: Replace the reader controller PCB. |
| Error code: | E220-0001 |
| Description: | A fault is detected on the inverter PCB for the scanning lamp |
| Causes: | The inverter PCB is faulty. The reader controller PCB is faulty. |
| Remedy: | 1. Wiring Is the wiring from the scanning lamp to the reader controller PCB normal? NO: Connect the connector firmly, and correct or replace the wiring. 2. Inverter PCB, Reader controller PCB Try replacing the lamp inverter PCB. Is the problem corrected? YES: End. NO: Replace the reader controller PCB. |
| Error code: | E225-0000 |
| Description: | Error in light intensity of the lamp |
| Causes: | Decrease of light intensity of the lamp. |
| Remedy: | Replace reader unit. |
| Error code: | E225-0002 |
| Description: | The light intensity of the CIS is faulty. During DF stream reading, the sheet-to-sheet light intensity is faulty. |
| Causes: | The scanning lamp is faulty. The CCD PCB is faulty. The rear controller PCB is faulty. |
| Remedy: | Disconnect and then connect the flexible cable. Replace the following as necessary: flexible cable, CIS, reader controller PCB. |
| Error code: | E240-0000 |
| Description: | Error in communication between main controller and DC controller Serial communication error |
| Causes: | The main controller PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check the connector connections. Check the DC controller PCB (MAISY). Replace the No.1 main controller circuit. |
| Error code: | E240-010B |
| Description: | The main controller PCB. The DC controller PCB is faulty. An error occurred in the sequence during printing. |
| Error code: | E243-0000 |
| Description: | Control panel unit error Communication between the main controller and the control panel unit is abnormal. |
| Causes: | The control panel CPU PCB is faulty. The main controller PCB is faulty. |
| Remedy: | Check on connection between the main controller PCB and the control panel unit |
| Error code: | E248-0001 |
| Description: | EEPROM access error |
| Causes: | Error at EEPROM power-on EEPROM data cannot be read at power-on. |
| Remedy: | Replace reader unit. |
| Error code: | E248-0002 |
| Description: | EEPROM access error |
| Causes: | Error in EEPROM writing EEPROM writing cannot be performed. |
| Remedy: | Replace reader unit. |
| Error code: | E248-0003 |
| Description: | EEPROM access error |
| Causes: | Error in EEPROM reading after writing EEPROM reading cannot be performed after writing is performed. |
| Remedy: | Replace reader unit. |
| Error code: | E302-0001 |
| Description: | Shading error |
| Causes: | When the light intensity is below the reference level at shading |
| Remedy: | 1. Disconnect and then connect the Flexible Cable. 2. Replace the Flexible Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB (PCB2). |
| Error code: | E302-0002 |
| Description: | Shading error |
| Causes: | Image sampling for shading was not completed. |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Check the connection of the harness. 3. Replace the Main Controller PCB. 4. Replace the Reader Unit. |
| Error code: | E315-0007 |
| Description: | There is an error in image data. There is an error in JBIG encoding. |
| Remedy: | Turn off and then back on the power. |
| Error code: | E315-0010 |
| Description: | Abnormality of image data ASIC (for compression/decompression) on the image conversion PCB is faulty. Timeout error during decoding |
| Remedy: | Check on connection of the image conversion board, Replace the image conversion board |
| Error code: | E412-0001 |
| Description: | Failure in drive of the Scanner Unit Cooling Fan (Reader Assembly). The Scanner Unit Cooling Fan was not driven. |
| Remedy: | 1. Disconnect and then connect the connector. 2. Check if there is open circuit. 3. Replace the corresponding fan. 4. Replace the DADF Driver PCB. |
| Error code: | E420-0001 |
| Description: | When the power switch of the host machine is turned on, the back-up data from the EEPROM cannot be read or the data that has been read has a fault |
| Causes: | The EEPROM is faulty. The ADF controller PCB is faulty. |
| Error code: | E421-0001 |
| Description: | The back-up data cannot be written to the EEPROM, or the data that has been written has a fault |
| Causes: | The EEPROM has a fault. The ADF controller PCB has a fault. |
| Error code: | E422-0001 |
| Description: | While the ADF is in standby, the communication with its host machine is disrupted for 5 sec or more; or, while the ADF is in operation, the communication with its host machine is disrupted for 0.5 sec or more |
| Causes: | The IPC communication is faulty. The communication line has an open circuit. The ADF controller PCB is faulty. |
| Error code: | E500-0001 |
| Description: | Finisher communication error Data communication could not be performed normally. It has been retried three times in vain. |
| Remedy: | - Check the connectors of the finisher controller PCB and DC controller PCB for normal connection. - Replace the finisher controller PCB. - Replace the DC controller PCB. |
| Error code: | E503-0002 |
| Description: | Saddle communication error When communication with the saddle stitcher is interrupted |
| Remedy: | - Check the connections between the saddle stitcher controller PCB and finisher controller PCB. - Replace the saddle stitcher controller PCB and finisher controller PCB. |
| Error code: | E504-0001 |
| Description: | There is a fault in stack size detection. Finisher-N1/Saddle Finisher-N2 The height sensor (PS1) is faulty. The communication between the height sensor and the finisher controller PCB is prevented. Or, there is a fault in the communication data. |
| Error code: | E504-0002 |
| Description: | There is a fault in stack size detection. Finisher-N1/Saddle Finisher-N2 The height sensor (PS1) is faulty. The communication between the height sensor and the finisher controller PCB is prevented for 0.1 sec or more. |
| Error code: | E504-0003 |
| Description: | There is a fault in stack size detection. Finisher-N1/Saddle Finisher-N2 The connector of the height sensor (PS1) is faulty. This fault is detected at power-on. |
| Error code: | E504-0004 |
| Description: | There is a fault in stack size detection. Finisher-N1/Saddle Finisher-N2 The DIP switch for the height sensor (PS1) is not adjusted correctly. There is a fault in the adjustment of the sensor by the DIP switch. |
| Causes: | The output of the height sensor (PS1) is faulty. |
| Error code: | E505-0001 |
| Description: | Finisher backup memory error When the checksum value calculated by the CPU differs from the checksum values of the data held inside the RAM |
| Causes: | The backup RAM is faulty. |
| Remedy: | Replace the finisher controller PCB. |
| Error code: | E505-0002 |
| Description: | Finisher backup memory error When the verify processing is not completed even after 2000 ms have elapsed during data writing |
| Causes: | The EEPROM is faulty. The finisher controller PCB is faulty. The puncher driver PCB is faulty. |
| Remedy: | Replace the finisher controller PCB. |
| Error code: | E512-0001 |
| Description: | There is a fault in delivery. Finisher-N1/Saddle Finisher-N2 The delivery roller, feed motor (M2), or feed motor clock sensor (PI10) is faulty. The delivery motor clock sensor fails to generate the target number of clock pulses within 10 sec at the start of operation. |
| Causes: | The delivery motor is faulty. The delivery motor clock sensor (PI10) is faulty. |
| Error code: | E512-0002 |
| Description: | There is a fault in delivery. Finisher-N1/Saddle Finisher-N2 The delivery roller, feeder motor (M2), or feeder motor clock sensor (PI10) is faulty. There is no clock pulse for a feed equivalent for 0.2 during communication. |
| Causes: | The delivery motor is faulty. The delivery motor clock sensor (PI10) is faulty. |
| Error code: | E530-0001 |
| Description: | There is a fault in alignment. Finisher-N1/Saddle Finisher-N2 There is an excess load on the alignment motor (M3), aligning plate home position sensor (PI6), or aligning plate. The aligning plate does not leave the aligning plate home position sensor when the alignment motor has been driven for 2 sec. |
| Causes: | The alignment motor (M3) is faulty. The alignment plate home position sensor (PI6) is faulty. |
| Remedy: | Replace the front adjuster plate HP sensor (PI36) , Replace the front adjuster plate motor (M33) |
| Error code: | E530-0002 |
| Description: | There is a fault in alignment. Finisher-N1/Saddle Finisher-N2 There is an excess load on the rear alignment motor (M3), rear aligning plate home position sensor (PI6), or rear aligning plate. The aligning plate does not return to its home position when the aligning plate motor has been driven for 2 sec. |
| Causes: | The alignment motor (M3) is faulty. The alignment plate home position sensor (PI6) is faulty. |
| Remedy: | Replace the front adjuster plate HP sensor (PI36) , Replace the front adjuster plate motor (M33) |
| Error code: | E531-0001 |
| Description: | - Staple unit failure - Staple HP sensor failure - Finisher controller PCB failure - The staple home position was not left when 400 ms have lapsed since start of staple operation. |
| Causes: | The stapler motor (M6) is faulty. The stapler home position sensor detecting switch (MS7) is faulty. |
| Remedy: | - Check the connector of the staple unit. - Replace the staple unit. - Replace the finisher controller PCB. |
| Error code: | E531-0002 |
| Description: | - Staple unit failure - Staple HP sensor failure - Finisher controller PCB failure - The staple home position had been left once, but it was not reached again when 400 ms have lapsed since start of staple operation. In addition, the staple home position could not be reached by performing reverse operation for 400 ms. |
| Causes: | The stapler motor (M6) is faulty. The stapler home position sensor detecting switch (MS7) is faulty. |
| Remedy: | - Check the connector of the staple unit. - Replace the staple unit. - Replace the finisher controller PCB. |
| Error code: | E532-0001 |
| Description: | There is a fault in the shift of the stapler. Finisher-N1/Saddle Finisher-N2 The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler shift base. The stapler shift base does not leave the stapler shift home position sensor when the stapler shift motor has been driven for 4 sec. |
| Causes: | The stapler shift motor (M4) is faulty. The stapler shift home position sensor (PI7) is faulty. |
| Remedy: | Replace the stapler shift HP sensor (PI50) , Replace the stapler shift motor (M35) |
| Error code: | E532-0002 |
| Description: | There is a fault in the shift of the stapler. Finisher-N1/Saddle Finisher-N2 The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler shift base. The stapler shift base does not return from the stapler shift home position sensor when the stapler shift motor has been driven for 4 sec. |
| Causes: | The stapler shift motor (M4) is faulty. The stapler shift home position sensor (PI7) is faulty. |
| Remedy: | Replace the stapler shift HP sensor (PI50) , Replace the stapler shift motor (M35) |
| Error code: | E535-0001 |
| Description: | There is a fault in the swing mechanism. Finisher-N1/Saddle Finisher-N2 The swing motor (M7) or the swing guide open sensor (PI18) is faulty. The swing guide closed switch does not go ON when the swing motor has been rotated in reverse for 1 sec. |
| Causes: | The delivery motor (M2) is faulty. The swing guide open sensor (PI18) is faulty. |
| Remedy: | Replace the swing HP sensor (PI35) , Replace the swing motor (M36) |
| Error code: | E535-0002 |
| Description: | There is a fault in the swing mechanism. Finisher-N1/Saddle Finisher-N2 The swing motor (M7) or the swing guide closed switch (MS6) is faulty. The swing guide open switch does not go ON when the swing motor has been rotated in reverse for 1 sec. |
| Causes: | The safety area switch (MS3) is faulty. The swing guide open detecting switch (MS6) is faulty. |
| Remedy: | Replace the swing HP sensor (PI35) , Replace the swing motor (M36) |
| Error code: | E535-0003 |
| Description: | There is an error in the staple swing mechanism. (finisher R1/R2) There is an error in relation to an hazardous area.. |
| Causes: | The delivery motor (M2) is faulty. The swing guide closed detecting switch 2 (MS6) is faulty. |
| Remedy: | 1) Check the swing home position sensor. Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor. Is the wiring normal? 3) Check the swing mechanism. Is there a fault? 4) Try replacing the swing motor. Is the problem corrected? |
| Error code: | E584-0001 |
| Description: | - Shutter drive motor or finisher controller PCB failure - Shutter open detection sensor failure - Shutter clutch failure - The shutter open sensor did not turn on when 1000 ms have lapsed since the shutter unit had performed open operation, resulting in incomplete open operation |
| Causes: | The feed motor (M1) is faulty. The shutter closed detecting switch (MS4) is faulty.PI20 |
| Remedy: | - Check the connector of the shutter open sensor. - Check the connector of the shutter clutch. - Check the connector of the shutter motor. - Replace the shutter open sensor. - Replace the shutter clutch. - Replace the shutter drive motor. - Replace the finisher controller PCB. |
| Error code: | E584-0002 |
| Description: | - Shutter drive motor or finisher controller PCB failure - Shutter open detection sensor failure - Shutter clutch failure - The shutter open sensor did not turn off when 1000 ms have lapsed since the shutter unit had performed close operation, resulting in incomplete close operation. |
| Causes: | The feed motor (M1) is faulty. The shutter open sensor (PI5) is faulty. |
| Remedy: | - Check the connector of the shutter open sensor. - Check the connector of the shutter clutch. - Check the connector of the shutter motor. - Replace the shutter open sensor. - Replace the shutter clutch. - Replace the shutter drive motor. - Replace the finisher controller PCB. |
| Error code: | E584-0003 |
| Description: | There is a fault in feed operation (No. 2). Finisher-N1/Saddle Finisher-N2 The safety area detecting switch (MS3) or the shutter closed switch (MS4) is faulty. The shutter closed switch is OFF when the tray 1/2 is in the OFF position of the safety area switch while the tray ascent/ descent motor is in operation. |
| Causes: | The safety area switch (MS3) is faulty. The shutter closed detecting sensor (MS4) is faulty. |
| Error code: | E590-0001 |
| Description: | Puncher motor error The puncher HP sensor fails to be detected after the puncher motor is driven for 200ms. |
| Causes: | The puncher home position sensor (PI1P) is faulty. The puncher motor (M1P) is faulty. The puncher motor clock sensor (PI3P) is faulty. The puncher driver PCB is faulty. |
| Remedy: | Replace the puncher HP sensor, Replace the puncher motor |
| Error code: | E590-0002 |
| Description: | Puncher motor error The puncher fails to detect the puncher HP sensor after the puncher motor stops during initial operation. |
| Causes: | The puncher home position sensor (PI1P) is faulty. The puncher motor (M1P) is faulty. The puncher motor clock sensor (PI3P) is faulty. The puncher driver PCB is faulty. |
| Remedy: | Replace the puncher HP sensor, Replace the puncher motor |
| Error code: | E593-0001 |
| Description: | Puncher shift motor error The HP sensor fails to be OFF. |
| Causes: | The horizontal registration home position sensor (PI2P) is faulty. The puncher shift motor (M2P) is faulty. The puncher drive PCB is faulty |
| Remedy: | Replace the HP sensor, Replace the puncher shift motor |
| Error code: | E593-0002 |
| Description: | Puncher shift motor error The HP sensor fails to be ON. |
| Causes: | The horizontal registration home position sensor (PI2P) is faulty. The puncher shift motor (M2P) is faulty. The puncher drive PCB is faulty |
| Remedy: | Replace the HP sensor, Replace the puncher shift motor |
| Error code: | E5F0-0001 |
| Description: | There is an error in saddle paper positioning. The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for 1.33 sec. The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty. |
| Causes: | The positioning plate motor (M4S) is faulty. The power positioning plate home position sensor (PI7S) is faulty. |
| Remedy: | Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S). |
| Error code: | E5F0-0002 |
| Description: | There is an error in saddle paper positioning. The paper positioning plate home position sensor does not turn off when the paper positioning plate motor has been driven for 1 sec. The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty. |
| Causes: | The positioning plate motor (M4S) is faulty. The power positioning plate home position sensor (PI7S) is faulty. |
| Remedy: | Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S). |
| Error code: | E5F1-0001 |
| Description: | There is an error in saddle paper folding. The number of detection pulses of the paper folding motor clock sensor is lower than specified. The paper folding home position sensor or the paper folding motor clock sensor (P14S) is faulty. |
| Causes: | The folding motor (M2S) is faulty. The folding motor clock sensor (PI4S) is faulty. |
| Remedy: | Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S). |
| Error code: | E5F1-0002 |
| Description: | There is an error in saddle paper folding. The state of the paper folding home position sensor does not change when the paper folding motor has been driven for 3 sec. The paper folding motor (M2S) or the paper folding motor clock sensor (P14S) is faulty. |
| Causes: | The folding roller home position sensor (PI12) is faulty. The stapler/folder motor (M7) is faulty. The stapler/folder clock sensor (PI14) is faulty. The finisher controller PCB is faulty. |
| Remedy: | Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S). |
| Error code: | E5F2-0001 |
| Description: | There is an error in the saddle guide. The guide home position sensor does not turn on when the guide motor has been driven for 0.45 sec. The guide motor (M3S) or the guide home position sensor (PI3S) is faulty. |
| Causes: | The guide motor (M3S) is faulty. The guide home position sensor (PI13S) is faulty. |
| Remedy: | Check the guide motor (M3S) /guide home position sensor (PI13S). |
| Error code: | E5F2-0002 |
| Description: | There is an error in the saddle guide. The guide home position sensor doest not turn off when the guide motor has been driven for 1 sec. The guide motor (M3S) or the guide home position sensor (PI3S) is faulty. |
| Causes: | The guide motor (M3S) is faulty. The guide home position sensor (PI13S) is faulty. |
| Remedy: | Check the guide motor (M3S) /guide home position sensor (PI13S). |
| Error code: | E5F3-0001 |
| Description: | There is an error in saddle alignment. The aligning plate home position sensors does not turn on when the alignment motor has been driven for 05. sec (during initialization, 1.67 sec). The alignment motor (M5S) or the aligning plate home position sensor (PI5S) is faulty. |
| Causes: | The alignment motor (M5S) is faulty. The alignment plate home position sensor (PI5S) is faulty. |
| Remedy: | Check the alignment motor (M5S) /aligning plate home position sensor (PI5S). |
| Error code: | E5F3-0002 |
| Description: | There is an error in saddle alignment. The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec. The alignment motor (M5S) for the alignment plate home position sensor (PI5S) is faulty. |
| Causes: | The alignment motor (M5S) is faulty. The alignment plate home position sensor (PI5S) is faulty. |
| Remedy: | Check the alignment motor (M5S) /aligning plate home position sensor (PI5S). |
| Error code: | E5F4-0001 |
| Description: | There is an error in saddle rear sampling. The stitching home position sensor does not turn on when the stapler motor (rear) is rotated in reverse for 0.5 sec or more. The switch motor (rear, M65) or the stitching home position sensor (rear, MS5S) is faulty. |
| Causes: | The stitch motor (rear, M6S) is faulty. The stitching home position switch (rear, PS2S) is faulty. |
| Remedy: | Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S) |
| Error code: | E5F4-0002 |
| Description: | There is an error in saddle rear sampling. The stitching home position sensor does not turn off when the switch motor (rear) is reverse for 0.5 sec or more. The switch motor (rear, M6S) or the stitching home position sensor (rear, MS5S) is faulty. |
| Causes: | The stitch motor (rear, M6S) is faulty. The stitching home position switch (rear, PS2S) is faulty. |
| Remedy: | Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S). |
| Error code: | E5F5-0001 |
| Description: | There is an error in saddle front stapling. The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0.5 sec or more. The stitch motor (front, M7S) or the stitching home position sensor (front, MS7S) is faulty. |
| Causes: | The stitching motor (front, M7S) is faulty. The stitching motor operating home position switch (front, PS4S) is faulty. |
| Remedy: | Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S). |
| Error code: | E5F5-0002 |
| Description: | There is an error in saddle front stapling. The stitching home position sensor does not turn off when the switch motor (front) is rotated in normal direction for 0.5. The stitch motor (front, M7S) or the switching home position sensor (front, MS7S) is faulty. |
| Causes: | The stitching motor (front, M7S) is faulty. The stitching motor operating home position switch (front, PS4S) is faulty. |
| Remedy: | Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S). |
| Error code: | E5F6-0001 |
| Description: | There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI4S) is faulty. The paper pushing plate home position sensor does not go ON when the paper pushing plate motor has been driven for 0.3 sec or more. |
| Causes: | The paper push-on plate motor (M8S) is faulty. The paper push-on plate home position sensor (PI14S) is faulty. |
| Remedy: | Replace the paper pressure plate motor (M8S), Replace the paper pressure plate HP sensor (PI14S) |
| Error code: | E5F6-0002 |
| Description: | There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate home position sensor (PI14S) is faulty. The paper pushing plate home position sensor does not go OFF when the paper pushing plate motor has been driven for 80 msec. |
| Causes: | The paper push-on plate motor (M8S) is faulty. The paper push-on plate leading edge position sensor (PI15S) is faulty. |
| Remedy: | Replace the paper pressure plate motor (M8S), Replace the paper pressure plate HP sensor (PI14S) |
| Error code: | E5F6-0003 |
| Description: | There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty. The paper pushing plate leading edge position sensor does not go OFF when the paper pushing plate motor has been driven for 80 msec. |
| Causes: | The paper push-on plate motor (M8S) is faulty. The paper push-on plate leading edge position sensor (PI15S) is faulty. |
| Remedy: | Replace the paper pressure plate motor (M8S), Replace the paper pressure plate motor clock sensor (PI1S) |
| Error code: | E5F6-0004 |
| Description: | There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate motor clock sensor (PI1S) is faulty. The number of detection pulses of the paper pushing plate motor clock sensor has dropped below a specific value. |
| Causes: | The paper push-on plate motor (M8S) is faulty. The paper push-on plate motor clock sensor (PIS) is faulty |
| Remedy: | Replace the paper pressure plate motor (M8S), Replace the paper pressure plate leading edge sensor (PI15S) |
| Error code: | E5F6-0005 |
| Description: | There is a fault in stapling by the saddle paper pushing plate. Saddle Unit The paper pushing plate motor (M8S) or the paper pushing plate leading edge position sensor (PI15S) is faulty. The paper pushing plate leading edge positioning sensor does not go ON when the paper pushing plate motor has been driven for 0.3 sec or more. |
| Causes: | The paper push-on plate motor (M8S) is faulty. The paper push-on leading edge position sensor (PI15S) is faulty. |
| Remedy: | Replace the paper pressure plate motor (M8S), Replace the paper pressure plate leading edge sensor (PI15S) |
| Error code: | E5F8-0001 |
| Description: | There is an error in the saddle connector. The connector of the guide home position sensor is identified as being disconnected. The connector of the guide home position sensor (PI3S) is faulty. |
| Causes: | The guide home position sensor (PI13S) has a faulty connector. |
| Remedy: | Check the connectors of the guide home position sensor (PI13S). Check the connectors of the paper pushing plate home position sensor (PI4S). |
| Error code: | E5F8-0002 |
| Description: | There is an error in the saddle connector. The connector of the paper pushing plate home position sensor is identified as being disconnected. The connector of the paper pushing plate home position sensor (PI14S) is faulty. |
| Causes: | The paper push-on plate home position sensor (PI14) has a faulty connector. |
| Remedy: | Check the connectors of the paper pushing plate leading edge position sensor (PI5S). |
| Error code: | E5F8-0003 |
| Description: | There is an error in the saddle connector. The connector of the paper pushing plate leading edge position sensor is identified as being disconnected. The connector of the paper pushing plate leading edge sensor (PI15S) is faulty. |
| Causes: | The paper push-on plate leading edge sensor (PI15S) has a faulty connector. |
| Remedy: | Check the connectors of the paper pushing plate leading edge position sensor (PI5S). |
| Error code: | E5F9-0001 |
| Description: | There is an error in the saddle switch. With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open. The inlet cover switch (MS1S), front cover switch (MS2S), or delivery cover switch (MS3S) is faulty. |
| Causes: | The inlet door open detecting switch (MS1S) is faulty. The inlet door sensor (PI9S) is faulty. |
| Remedy: | Check the inlet cover switch (MS1S)/front cover switch (MS2S)/delivery cover switch (MS3S). |
| Error code: | E5F9-0002 |
| Description: | There is an error in the saddle switch. With any of the following sensor is identifying its respective cover as being closed, the front cove switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cove sensor (PI3S) The front cove switch (MS2S) or the delivery cover switch (MS3S) is faulty. |
| Causes: | The front door open detecting switch (MS2S) is faulty. The front door open sensor (PS2S) is faulty. |
| Remedy: | Check the front cover switch (MS2S)/delivery cover switch (MS3S). |
| Error code: | E5F9-0003 |
| Description: | There is an error in the saddle switch. With any of the following sensors identifying its respective cover as being closed, the delivery cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - delivery cover switch (MS3S) |
| Causes: | The delivery door open detecting switch (MS3S) is faulty. The delivery door open sensor (PI3S) is faulty. |
| Remedy: | Check the delivery cover switch (MS3S). |
| Error code: | E601-0000 |
| Description: | Abnormality of image memory Communication error of the image memory (SDRAM) |
| Causes: | The wiring is faulty (short circuit, open circuit). The HDD is faulty. The DC controller PCB is faulty. The main controller PCB is faulty. |
| Remedy: | Replace the SDRAM |
| Error code: | E601-0001 |
| Description: | When an image is transferred between the main controller PCB and the DC controller PCB, the DC controller PCB detects a fault in the control information |
| Causes: | The wiring is faulty (short circuit, open circuit). The HDD is faulty. The DC controller PCB is faulty. The main controller PCB is faulty. |
| Remedy: | 1. Wiring Are the connection and cable between the connector J122 on the DC controller PCB and the connector J1015 on the main controller PCB normal? NO: Correct the connection/cable. 2. DC controller PCB, Main controller PCB Try replacing the DC controller PCB. Is the problem corrected? YES: End. NO: Replace the main controller PCB. |
| Error code: | E602-0001 |
| Description: | HDD error |
| Causes: | Lack of the HDD capacity The capacity of the HDD installed is smaller than that of the HDD used in the software. |
| Error code: | E602-0002 |
| Description: | HDD error |
| Causes: | Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged. |
| Remedy: | Burn the Bootable CD again. |
| Error code: | E602-0003 |
| Description: | HDD error |
| Causes: | HDD access error An error occurred caused by the device or hardware when accessing to the HDD during execution of bootrom. (Damage to the sector / Busy device status, etc.) |
| Remedy: | Turn on the power again. |
| Error code: | E602-0004 |
| Description: | The wiring is faulty (short circuit, open circuit). The hard disk drive is faulty. The main controller PCB is faulty. A an error is found in the read/write address for the hard disk. |
| Error code: | E607-0000 |
| Description: | The hard disk fan (FM7) is faulty. The wiring is faulty (short circuit, open circuit). The DC controller PCB is faulty. While the hard disk fan (FM7) is being driven, the clock signal (FM7CLK) does not arrive for 5 secs or more. |
| Error code: | E677-0001 |
| Description: | DPRAM size error In communication for initialization, the DPRAM size returned by the PDL board to the host machine has an error. (The host machine is aware of the DPRAM size in advance; the DPRAM is a dual-port RAM used for communication between the host machine and the PDL board, and is mounted on the PDL board.) |
| Causes: | The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty. |
| Remedy: | 1. Connector Is the printer board (accessory) connected correctly? NO: Correct the connection. 2. Printer board, Main controller PCB Try replacing the printer board. Is the problem corrected? YES: End. NO: Replace the main controller PCB. |
| Error code: | E710-0001 |
| Description: | IPC initializing error When the ready status fails to be established within 3 sec. after the IPC chip started up |
| Causes: | The DC controller PCB is faulty. The reader controller PCB is faulty. The machine controller PCB is faulty. |
| Remedy: | Check the cable connections. |
| Error code: | E710-0002 |
| Description: | There is an error in the initialization of the IPC. The IPC (IC40) on the DC controller PCB cannot be initialized when the main power supply is turned on. |
| Causes: | The DC controller PCB is faulty. The reader controller PCB is faulty. The machine controller PCB is faulty. |
| Remedy: | - Check the cable. - Replace the DC controller PCB. |
| Error code: | E710-0003 |
| Description: | There is an error in the initialization of the IPC. The IPC (IC1003) on the machine controller PCB cannot be initialized when the main power is turned on. |
| Causes: | The DC controller PCB is faulty. The reader controller PCB is faulty. The machine controller PCB is faulty. |
| Remedy: | - Check the cable. - Replace the main controller PCB. |
| Error code: | E711-0001 |
| Description: | IPC communication error When error occurrence was set 4 or more times in the error register of the IPC chip within 1.5 sec. |
| Causes: | The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty. |
| Remedy: | Check the cable connections. Replace the ADF controller PCB. Replace the reader controller PCB. |
| Error code: | E711-0002 |
| Description: | There is an IPC communication error. An error has been detected 4 times or more within 1.5 sec after the communication has been interrupted between the finisher and the printer, and the machine does not reset. |
| Causes: | The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty. |
| Remedy: | Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to reset, check the connector between the finisher and the copier for poor contact; as necessary, replace the finisher controller/DC controller. |
| Error code: | E711-0003 |
| Description: | There is an error in the IPC communication. Data has been written to the error register of the IPC (IC1003) on the main controller PCB 4 times or more within 2 sec. |
| Causes: | The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty. |
| Remedy: | - Check the cable. - Replace the main controller PCB. |
| Error code: | E712-0001 |
| Description: | Communication error between the ADF and the reader Communication between the reader and the ADF stops, and the communication cannot recover for 5 sec. or more. |
| Causes: | The connect has poor connection. The main power supply PCB is faulty. The ADF controller PCB is faulty. The reader controller PCB is faulty. |
| Remedy: | Check on connection of the cable, Replace the ADF controller PCB, Replace the reader controller PCB |
| Error code: | E712-0002 |
| Description: | The transmission bit is not enabled 10 sec or more in the sync register of the communication IC (IPC) on e reader controller PCB |
| Causes: | The connect has poor connection. The main power supply PCB is faulty. The ADF controller PCB is faulty. The reader controller PCB is faulty. |
| Remedy: | 1. Connector Is the interface able between the ADF controller PCB and the reader controller PCB normal? NO: Correct the cable. 2. Main power supply PCB While the ADF is in operation, does the voltage between J203-2 (+) and J203-1 (-) on the main power supply PCB change from 0 to about 24 V? NO: Replace the main power supply PCB. 3. ADF controller PCB, Reader controller PCB Try replacing the ADF controller PCB. Is the problem corrected? YES: End. NO: Replace the rear controller PCB. |
| Error code: | E713-0000 |
| Description: | Communication error between the finisher and the printer Communication between the finisher and the copier stops. |
| Causes: | The connector has poor connection. The option power supply PCB is faulty. The finisher controller PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check on connection of the cable, Replace the finisher controller PCB, Replace the DC controller PCB |
| Error code: | E717-0001 |
| Description: | Error in communication with NE controller When the NE controller which was connected before the power was turned OFF could not be recognized when the power was turned back ON |
| Causes: | The wiring is faulty (short circuit, open circuit). The DA unit PCB is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR. |
| Remedy: | Check the cable connections. |
| Error code: | E719-0001 |
| Description: | Error in communication with coin vendor/card reader When the coin vendor which was connected before the power was turned OFF could not be recognized when the power was turned back ON |
| Causes: | The wiring is faulty (short circuit, open circuit). The Card Reader-C1 is faulty. The coin vendor is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR. |
| Remedy: | Check the cable connections. |
| Error code: | E732-0001 |
| Description: | Scanner communication error |
| Causes: | Scanner communication error |
| Remedy: | 1. Update the firmware. 2. Replace the Main Controller PCB. |
| Error code: | E732-9999 |
| Description: | There is an error in reader communication. Although a printer model, the machine is identified as a reader unit at start-up. (A copier model is started up as a printer model when the RAM is initialized.) |
| Remedy: | Turn off and then on the main power. |
| Error code: | E733-0001 |
| Description: | Printer communication error (Invalid communication after communication is established, Parity error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E740-0001 |
| Description: | At power-on, the LAN card has a fault |
| Causes: | The LAN card is faulty. The main controller PCB is faulty. |
| Remedy: | 1. Connector Is the connection between the LAN card and the main controller PCB normal? NO: Correct the connection. 2. LAN card, Main controller PCB Try replacing the LAN card. Is the problem corrected? YES: End. NO: Replace the main controller PCB. |
| Error code: | E740-0002 |
| Description: | Error detection on either Network Board or Mac address |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board. |
| Error code: | E740-0003 |
| Description: | Abnormality of the Ethernet board Incorrect network ID is detected at startup. |
| Causes: | The LAN card is faulty. The main controller PCB is faulty. |
| Remedy: | Replace the Ethernet board, Replace the main controller PCB (sub LAN-bar) |
| Error code: | E741-0000 |
| Description: | The PCI bus has a fault |
| Causes: | The PCI bus has poor connection. The main controller PCB is faulty. |
| Remedy: | Each PCI slot may be disabled in service mode to prevent the error: BOARD>PCI1-OFF through PCI3-OFF. 1. Board Is the connection between the relay board and the main controller PCB normal? NO: Correct the connection. 2. Relay board, Main Controller PCB Try replacing the relay board. Is the problem corrected? YES: End. NO: Replace the main controller PCB. |
| Error code: | E743-0000 |
| Description: | Error in main controller communication An error in reading of/writing to the Flash ROM in the Main Controller occurred. |
| Causes: | Software sequence error |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. |
| Error code: | E744-0001 |
| Description: | Language file/boot ROM/USB memory error The language file version does not match Bootable. |
| Causes: | Language file version error The language file version does not match Bootable. |
| Remedy: | Download a language file of the correct version. |
| Error code: | E744-0002 |
| Description: | Language file/boot ROM/USB memory error The language file is longer than the permitted size. |
| Causes: | Language file size error The language file is longer than the permitted size. |
| Remedy: | Download a language file of the correct version. |
| Error code: | E744-0003 |
| Description: | Language file/boot ROM/USB memory error The language file version does not match Bootable |
| Causes: | Language file version error The language file version does not match Bootable. |
| Error code: | E744-0004 |
| Description: | Language file/boot ROM/USB memory error Language file read error |
| Causes: | Language file read error Reading of language file is invalid. |
| Remedy: | Download a language file of the correct version. |
| Error code: | E744-1000 |
| Description: | Mismatch of the series or model of the firmware sent at the time of downloading |
| Remedy: | Check the supported series or model of the firmware, and burn the correct series or model of firmware. |
| Error code: | E744-2000 |
| Description: | There is an error in the language file/boot ROM. The engine ID indicated by the software ID is illegal. |
| Remedy: | Replace it with a software ID of the correct model. |
| Error code: | E804-0000 |
| Description: | Power supply fan failure |
| Error code: | E805-0001 |
| Description: | Error in duplex cooling fan |
| Causes: | Fan 1 failure |
| Error code: | E805-0002 |
| Description: | Fan Motor 2 error |
| Causes: | The Sub Fan fails to rotate at the specified rotation speed. |
| Remedy: | 1. Check the connection of the Sub Fan. 2. Replace the Sub Fan. |
| Error code: | E824-0000 |
| Description: | There is an error in the primary charging suction/primary charging exhaust fan. There is an error in the primary charging suction mechanism. |
| Remedy: | Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch. |
