Canon imageRUNNER 6800CN

Общие характеристики
Тип устройства	МФУ
Копир
Сканер
Область применения	большой офис
Размещение	напольный
Цветность печати	цветная
Факс
Печать фотографий
Телефон
Макс. формат	A3
Тип	лазерный/светодиодный
Технология печати	лазерная
Прямая печать
Печать без полей
Пигментные чернила
Двусторонняя печать
Время разогрева	540
Макс, разрешение для ч/б печати
По Y	600
По X	2 400
Скорость ч/б печати
A4	68
A3	16
Скорость цветной печати
A3	8
A4	28
Время выхода первого отпечатка
Цветн,	12,2
Ч/б	5,3
Макс, количество копий за цикл	999
Шаг масштабирования	0,01
Время выхода первой копии	5
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По Y	600
По X	600
Тип сканера	планшетный/протяжный
Макс. формат оригинала	A3
Оттенки серого	256
Макс, размер сканирования
По Y	432
По X	297
Количество картриджей	1
Печать на:
Глянцевой бумаге
Карточках
Конвертах
Этикетках
Пленках
Матовой бумаге
Рулоне
CD/DVD
Фотобумаге
Плотность бумаги
Минимальная	64
Максимальная	250
Caller ID
Беспроводная трубка
АОН
Спикерфон
Стандарт DECT
Автоответчик
Проводная трубка
Языки управления
PostScript
PostScript 3
PCL 5c
PDF
PCL 5e
PCL 6
PostScript 2
PPDS
Подача бумаги
Стандартная	4 200
Вывод бумаги
Стандартный	500
Сортер
Сортировка со сдвигом
Степлер
Брошюровщик
USB
Ethernet (RJ-45)
Веб-интерфейс
Версия USB	2,0
LPT
RS-232
Устройство для чтения карт памяти
Wi-Fi
Bluetooth
FireWire (IEEE 1394)
Инфракрасный порт
Объем памяти	768
Емкость жесткого диска	40
Мин. системные требования
Экран
Поддержка ОС
Windows
Mac OS
DOS
Linux
Потребляемая мощность
При работе	1 650
Вес	226
Глубина	852
Ширина	679
Высота	1 191

Error code:	E000-0010
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. After power-on, the temperature does not reach 50 deg C within 300 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0011
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 50 deg C, but does not reach 80 deg C within 300 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0012
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 80 deg C, but does not reach 110 deg C within 300 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0013
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 110 deg C, but does not reach 140 deg C within 300 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0014
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 140 deg C, but does not reach 170 deg C within 300 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0015
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 170 deg c, but does not reach 200 deg C within 300 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0020
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. After power-on, the temperature does not reach 50 deg C within 180 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0021
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 50 deg C, but does not reach 80 deg C within 180 sec.
Causes:	The fixing heater is faulty. The SSR is faulty. The fixing thermistor is faulty. The thermistor (TH1, TH2) has an open circuit. The thermal switch (TP1) has turned on.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0022
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 80 deg C, but does not reach 110 deg C within 180 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0023
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 110 deg C, but doest not reach 140 deg C within 180 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0024
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 140 deg C, but does not reach 170 deg C within 180 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0025
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 170 deg C, but does not reach 200 deg C within 180 sec. If the outside heating roller is in contact, within 400 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0026
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 200 deg C, but does not reach 230 deg C within 180 sec. If the outside heating roller is in contact, within 400 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0030
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. After power-on, the temperature does not reach 50 deg C within 420 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0031
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 50 deg C, but does not reach 80 C deg in 420 sec.
Causes:	The fixing heater is faulty. The SSR is faulty. The fixing thermistor is faulty. The thermistor (TH1, TH2) has an open circuit. The thermal switch (TP1) has turned on.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0032
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 80 deg C, but does not reach 110 deg C within 420 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0033
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 110 deg C, but does not reach 140 deg C within 420 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E000-0034
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. The temperature reaches 140 deg C, but does not reach 170 deg C within 420 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E001-0001
Description:	Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control.
Causes:	The sub thermistor detected a temperature of higher than 290 degree C.
Remedy:	- Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB.

Error code:	E001-0002
Description:	Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 1 has detected a high temperature (ASIC detection)
Causes:	The fixing film unit is faulty (i.e., the thermistor has a short circuit). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service move: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR.

Error code:	E001-0003
Description:	Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 2 has detected a high temperature (ASIC detection)
Remedy:	Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR.

Error code:	E001-00FF
Description:	The rise in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the following: main thermistor (THM1, THM2, THM3), sub thermistor (THM4, THM5, THM6), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB is faulty. When the cause (Detailed code) cannot be found in the DC controller PCB input-port as DC controller PCB detects instantly an abnormal signal from the thermistor.
Remedy:	After releasing the error with the procedure of COPIER>FUNCTION>CLEAR>ERR, 1. Turn off the switch of control panel. 2. Turn off the switch of main power. 3. Turn on the switch of main power. a. When the machine returns, Check the interconnection between the DC controller PCB and the thermistor. b. When the machine does not return, Follow the instruction the error (Detailed) code shows on the control panel.

Error code:	E002-0010
Description:	The rise in the temperature of the fixing assembly is not enough. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. The temperature of the fixing roller reaches 80 deg C, but drops below 50 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E002-0020
Description:	The rise in the temperature of the fixing assembly is not enough. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. The temperature of the outside heating roller reaches 80 deg C, but drops below 50 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E002-0030
Description:	The rise in the temperature of the fixing assembly is not enough. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. The temperature of the pressure roller reaches 80 deg C, but drops below 50 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E003-0041
Description:	After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. During standby, the temperature of the fixing roller drops below 150 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E003-0042
Description:	After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. During standby, the temperature of the outside heating roller drops below 190 dg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E003-0043
Description:	After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. During standby, the temperature of the pressure roller drops below 120 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E003-0051
Description:	After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. During copying, the temperature of the fixing roller drops below 150 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E003-0052
Description:	After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. During copying, the temperature of the outside heating roller drops below 190 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E003-0053
Description:	After standby, the drop in the temperature of the fixing assembly is excessive. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. During copying, the temperature of the pressure roller drops below 60 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0001
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the outside heating roller heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0002
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the fixing sub heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0003
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the outside heating roller heater or the fixing sub heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0004
Description:	Mismatch of Fixing Assembly type
Causes:	A fixing assembly of another product was installed.
Remedy:	1. Replace the fixing assembly with that of this product.

Error code:	E004-0005
Description:	Fixing Relay fusion error
Causes:	At power ON or recovery from sleep mode, a zero cross signal was detected three times during the period of 100 ms after completion of CPU initialization.
Remedy:	1. Check the harness/connector between the Fixing Assembly and the DC Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB.

Error code:	E004-0006
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the fixing sub heater or the fixing main heater
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0007
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the outside heating roller heater, fixing sub heater, or fixing main heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0008
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the pressure heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0009
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the outside heating roller heater or the contact heater
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-000A
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the fixing sub heater or the contact heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-000B
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the outside heating roller heater, fixing sub heater, or contact heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-000C
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an error in the fixing main heater or the contact heater
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-000D
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the outside heating roller heater, fixing main heater, or contact heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-000E
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an error in the fixing sub heater, fixing main heater, or contact heater.N>CLEAR>ERR.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-000F
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the outside heating roller heater, fixing sub heater, fixing main heater, or contact heater.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0010
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. The fixing roller thermistor has an open circuit.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0020
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. The outside heating roller thermistor has an open circuit.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0030
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. The pressure roller thermistor has an open circuit.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E005-0000
Description:	There is an error in the take-up mechanism of the web. The web of the fixing assembly has been fully taken up. After the web sensor has detected an off state, the count has exceeded 3000. The web length sensor (PS20) is faulty. The DC controller PCB is faulty.
Remedy:	Reset in service mode: COPIER>FUNCTION>CLEAR>ERR. If you have replaced the web, reset the reading in the following, and turn off and then on the power: COPIER>COUNTER>DRBL-1>FIX-WEB.

Error code:	E005-0010
Description:	There is an error in the take-up mechanism of the web. The drive solenoid of the fixing assembly is not connected.
Remedy:	Check the drive solenoid of the fixing web for disconnection; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E006-0001
Description:	The fixing assembly has a comparison error. The fixing drawer has been identified as being disconnected.
Causes:	The fixing drawer has poor contact. The fixing assembly is absent.
Remedy:	Check the connector of the drive solenoid of the fixing web; then, turn off and then on the main power.

Error code:	E008-0001
Description:	Fixing unit end-of-life detection error Fixing unit end-of-life detection error
Remedy:	Occurs when the fixing unit end-of-life is detected or when the belt pushoff temporary escape mode was executed but normal operation was not restored.

Error code:	E009-00FF
Description:	There is an outside heating roller shift error. The outside heating roller shift motor (M22) is faulty. The outside heating roller HP sensor (PS21) is faulty. The DC controller PCB is faulty. The outside heating roller remains in contact with the fixing roller
Remedy:	Check the outside heating roller shift motor and the fixing motor; then, turn off and then on the main power.

Error code:	E012-0001
Description:	Error in ITB motor activation.
Causes:	If the ITB motor speed detection signal comes off the specified cycle after it turned once to the specified cycle. Cause Failure in ITB motor, failure in DC controller PCB.
Remedy:	- Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB

Error code:	E013-0001
Description:	There is clogging by waste toner. There is a waste toner full error. the soft counter reading is 250000 or higher.
Causes:	The waste toner feedscrew has locked. The waste toner feed motor is faulty. The transfer high-voltage PCB is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check the amount of waste toner; then, turn off and then on the main power.

Error code:	E013-0002
Description:	There is clogging by waste toner. There is a waste toner feedscrew error. The output of the waste toner lock detecting switch (SW14) is `1` for more than 1 sec.
Causes:	The waste toner feedscrew has locked. The waste toner feed motor is faulty. The transfer high-voltage PCB is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check the developing motor; then, turn off and then on the main power.

Error code:	E014-0001
Description:	Fixing motor failure
Causes:	Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached.
Remedy:	Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor.

Error code:	E020-xx10
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Sig value is lower than 62. The ATR sensor is damage or has an open circuit. The connector may have poor contact. The intermediate transfer belt may be soiled.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xx11
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Ref value is lower than 62. The ATR sensor is damaged or has an open circuit. The connector may have poor contact. The intermediate transfer belt may be soiled
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xx12
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Sig value is 960 or higher. The ATR sensor is damaged or has an open circuit. The connector has poor contact. The opening/closing of the shutter is faulty. The intermediate transfer belt is soiled.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xx13
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the Ref value is 960 or higher. The ATR sensor is damaged or has an open circuit. The connector has poor contact. The intermediate transfer belt is soiled
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xx81
Description:	Concerning the first two digits of the details code in xx12 to xxD0 xx=01: Y xx=02: M xx=03: C xx=04: Bk Density value is extremely low for the ITB surface reflectivity when the new drum unit was installed. SALT sensor trouble. Dirty ITB.
Remedy:	Replace the SALT sensor (clean the sensor window). Replace the drum unit (check its connections). Replace the ITB (clean it).

Error code:	E020-xx90
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The result (Sig D) of computation based on the reading of the patch during patch detection (analog)) is lower than 16.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xx91
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The result (Sig D) of computation based on the reading of the patch during patch detection (analog) is 1008 or higher. The patch sensor is damaged or has an open circuit. The connector has poor contact. The primary transfer pressure is faulty. The mounting of the developing assembly is faulty.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xx92
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The value delta D obtained from the result (Sig D) of computation based on the reading of the patch during patch detection is -5.0% or more 3 times continuously. The patch sensor may be damaged or has an open circuit. The connector has poor contact. The primary transfer engagement is faulty. The mounting of the developing assembly is faulty. The amount of supply is low.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xx93
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The value delta D obtained from the result (Sig D) of computation based on the reading of the patch during patch detection is +5.0% or lower 3 times continuously. The patch sensor is damaged or has an open circuit. The connector has poor contact. The primary transfer pressure is faulty. The mounting of the developing assembly is faulty. The amount of supply is low.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxA0
Description:	Concerning the first two digits of the details code in xx12 to xxD0 xx=01: Y xx=02: M xx=03: C xx=04: Bk Measured value of the detected developer density is extremely low. Trouble in the ATR sensor. Trouble in the drum unit.
Remedy:	Replace the drum unit (check its connections).

Error code:	E020-xxA1
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For ATR control, the Ref value is lower than 62. The ATR sensor is damaged or has an open circuit. The connector has poor contact.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxA2
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For ATR control, the Sig value is 960 or higher. The ATR sensor is damaged or has an open circuit. The connector has poor contact. The opening/closing of the shutter is faulty.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxA3
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For ATR control, the Ref value is 960 or higher. The ATR sensor is damaged or has an open circuit. The connector has poor contact.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxA9
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The T/D ratio identified for ATR control has exceeded the lower limit (3%) 3 times continuously. The ATR sensor is damaged or has an open circuit. The connector has poor contact. The amount of supply is too low.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxC0
Description:	Concerning the first two digits of the details code in xx12 to xxD0 xx=01: Y xx=02: M xx=03: C xx=04: Bk Trouble in the supply of the toner from the toner cartridge to the developer. Too much toner is supplied to the developer. Broken or disconnected wire in the ATR sensor.
Remedy:	Replace the drum unit (check its connections).

Error code:	E020-xxC1
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The variation among the 8 samplings of the light Ref value is 100 or higher. The ATR sensor is damaged or has an open circuit. The connector has poor contact.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxC2
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The variation among the 8 samplings of the patch Sig value is 400 or higher. The patch sensor is damaged or has an open circuit. The connector has poor contact. The primary transfer engagement is faulty
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxD0
Description:	Concerning the first two digits of the details code in xx12 to xxD0 xx=01: Y xx=02: M xx=03: C xx=04: Bk No toner is supplied from the toner cartridge to the developer. TCRG motor fails to run. An empty cartridge is being used. The toner supply port of the drum unit is damaged. Broken or disconnected wire in the ATR sensor.
Remedy:	Replace the toner cartridge motor. Replace the drum unit (check its connections).

Error code:	E020-xxD1
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 462 or lower. The ATR sensor is damaged or has an open circuit. The connector has poor contact.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxD2
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction Fore INIT control (service mode INISET-*) at time of initial setup, the average of the patch Sig values is 200 or lower. The patch sensor is damaged or has an open circuit. the connector has poor contact. The primary transfer engagement is faulty. The mounting of the developing assembly is faulty.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxD4
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INTI control (service mode INISET-*) at time of initial setup, the average of the light Sig values is 800 or higher. The ATR sensor is damaged or has an open circuit. The connector has poor contact. The amount of supply is too high.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxD5
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INTI control (service mode INISET-*) at time of initial setup, the average of the light Ref values is 562 or higher. The ATR sensor is damaged or has an open circuit. The connector has poor contact.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxDA
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the variation among the 72 night Sig value samplings is 100 or more. The ATR sensor is damaged or has an open circuit. The connector has poor contact. The stirring of toner is faulty.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxDB
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*) at time of initial setup, the variation among the 72 light Ref samplings is 100 or more. The ATR sensor is damaged or has an open circuit. The connector has poor contact.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxDC
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction For INIT control (service mode INISET-*), the average of the patch Sig values is 800 or higher. The patch sensor is damaged or has an open circuit. The connector has poor contact. the primary transfer engagement if faulty. The mounting of the developing assembly is faulty. The amount of supply is too high.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E020-xxF1
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction The connector or the color toner supply clutch is not connected.
Remedy:	Turn off and then on the main power; then, execute ITB cleaning.

Error code:	E020-xxFF
Description:	There is an ATR error. xx=01 for Y; xx=02 for M; xx=03 for C; xx=04 for without color distinction There is no toner inside the Bk developing assembly. - the toner is not supplied to the developing assembly correctly. - the hopper stirring motor is not rotating normally. The hopper connector has poor contact. The black toner supply motor (M25) is faulty. The hopper stirring motor (M23) is faulty. The black toner level sensor is faulty. The DC controller is faulty.
Remedy:	Turn off and then on the main power; then, execute the intermediate transfer belt.

Error code:	E021-0001
Description:	There is an error in the rotation of the developing assembly. The developing rotary home position is not detected. The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is faulty; the wiring of the DC controller is faulty; there is an excess load on the developing assembly.
Remedy:	Turn off and then on the main power.

Error code:	E021-0002
Description:	There is an error in the rotation of the developing assembly. The length of the flag detected during rotation is longer or shorter than the designed flag. The motor rotates out of sync because of poor torque caused by any of the following: the developing rotary HP sensor is faulty; the wiring of the DC controller PCB is faulty; there is an excessive load on the developing assembly.
Remedy:	Turn off and then on the main power.

Error code:	E023-0001
Description:	The developing motor (M3) does not rotate normally. After motor start-up, a lock state is not detected for 1 sec or more.
Remedy:	Turn off and then on the main power.

Error code:	E025-0001
Description:	There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). There is an overcurrent in the hopper stirring motor (M23).
Remedy:	Turn off and then on the main power.

Error code:	E025-0002
Description:	There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). There is an over-current in the black toner supply motor (M25).
Remedy:	Turn off and then on the main power.

Error code:	E025-0410
Description:	There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). The connector of the black toner supply motor (M25) is identified as being disconnected.
Remedy:	Turn off and then on the main power.

Error code:	E032-0001
Description:	NE controller counter operation failure When the counter function of the NE controller does not work
Causes:	The DA unit is faulty. The main controller PCB is faulty.
Remedy:	Check the cable connections.

Error code:	E043-0001
Description:	There is an error in the 3.5K paper deck pickup motor, causing an error signal. After motor start-up, a lock state is not detected for 1 sec or more. The mechanical load such as on the feeding system is excessive.
Remedy:	Turn off and then on the main power.

Error code:	E051-0001
Description:	The horizontal registration home position is not detected within a specific period of time. The horizontal registration position is faulty (0003). The horizontal registration home position is not detected within a specific period of time.
Causes:	The side registration sensor (S32) is faulty. The side registration motor (M17) is faulty. The duplex driver PCB is faulty. The DC controller PCB is faulty.
Remedy:	Turn off and then on the main power.

Error code:	E051-0002
Description:	The horizontal registration home position is not detected within a specific period of time. The horizontal registration position is faulty (0003). The ON edge of the SUS plate is not detected during a search for home position.
Remedy:	Turn off and then on the main power.

Error code:	E051-0003
Description:	The horizontal registration home position is not detected within a specific period of time. The horizontal registration position is faulty (0003). The logical motor position differs between before and after the detection operation.
Remedy:	Turn off and then on the main power.

Error code:	E061-0001
Description:	At time of potential control, a specific level of potential is absent. Or, the limiter goes on. When forming an image, the potential is 10 V or less during initial rotation.
Remedy:	Turn off and then on the main power.

Error code:	E061-0002
Description:	At time of potential control, a specific level of potential is absent. Or, the limiter goes on. At time of potential control, the potential is 10 V or less during initial rotation
Remedy:	Turn off and then on the main power.

Error code:	E061-0003
Description:	At time of potential control, a specific level of potential is absent. Or, the limiter goes on. While the grid bias is being adjusted, a level of potential higher than the grid bias is sampled.
Remedy:	Turn off and then on the main power.

Error code:	E061-0005
Description:	At time of potential control, a specific level of potential is absent. Or, the limiter goes on. The difference in potential between dark and light areas is less than 100 V.
Remedy:	Turn off and then on the main power.

Error code:	E061-0007
Description:	At time of potential control, a specific level of potential is absent. Or, the limiter goes on. During adjustment of EPC offset, the potential that is read is outside the +/-30 V range.
Remedy:	Turn off and then on the main power.

Error code:	E061-0008
Description:	At time of potential control, a specific level of potential is absent. Or, the limiter goes on. During dark area potential adjustment, the sampling value is too low.
Remedy:	Turn off and then on the main power.

Error code:	E061-0010
Description:	At time of potential control, a specific level of potential is absent. Or, the limiter goes on. The sampling of the light area potential is faulty.
Remedy:	Turn off and then on the main power.

Error code:	E070-00xx
Description:	There is an error in the detection of the ITB home position. xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction The home position of the intermediate transfer belt is not detected within a specific period of time . The ITB HP sensor is faulty.
Remedy:	Turn off the main power, and check the DC controller PCB and the ITB HP sensor; then, turn on the main power.

Error code:	E070-01xx
Description:	There is an error in the detection of the ITB home position. xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction The period of time between when the home position of the intermediate transfer belt is detected and the next home position is detected is longer than specified . The presence of a tear may have caused the sensor to wrongly identify it as indicating the home position.
Remedy:	Turn off the main power, and check the drive of the intermediate transfer belt; then, turn on the main power.

Error code:	E070-02xx
Description:	There is an error in the detection of the ITB home position. xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction The period of time between when the home position of the intermediate transfer belt is detected and when the next home position is detected is shorter than specified . The intermediate transfer belt slips on the drive roller, causing a delay in the timing at which the home position is detected.
Remedy:	Turn off the main power, and check the surface of the intermediate transfer belt for a tear; then, turn on the main power.

Error code:	E070-03xx
Description:	There is an error in the detection of the ITB home position. xx=01: ITB home position sensor B, xx=02: ITB home position sensor A; only at ITB 1/1 speed; XX=00: no distinction The detection of the home position of the intermediate transfer belt has failed once. ITB home position sensor B and ITB home position sensor A must occur alternately; however, the same state has been detected continuously.
Remedy:	Turn off the main power, and check the DC controller PCB and the ITB HP sensor; then turn on the main power.

Error code:	E073-0001
Description:	With the front door closed, the transfer drawer connector or the transfer frame drawer connector is not connected. The result of detecting the feed unit indicates the absence of the unit.
Causes:	The transfer drawer connector has poor contact. The transfer unit is absent.
Remedy:	Turn off and then on the main power.

Error code:	E077-0001
Description:	The home position of the secondary transfer roller (engagement) is not detected. The HP sensor does not go on within 5 sec after the start of a HP search.
Remedy:	Turn off and then on the main power.

Error code:	E078-0001
Description:	Primary transfer disengagement mechanism failure
Causes:	Primary transfer disengagement mechanism failure At the time of searching the home position: Considering that the coupling of primary transfer engagement/ disengagement drive may not be connected, the solenoid was pulled for maximum 6 times in the condition where the flag was detected once. But the HP sensor did not detect the color print engagement position. * If a flag is not detected even once, it is considered that the ITB unit is absent. At the time of changing the position The position after turning ON/OFF of the solenoid did not match the HP sensor value.
Remedy:	Check whether the ITB unit is installed or not. Reconnect the connector J181 on the DC controller PCB. Check the primary transfer roller disengagement switch in the sensor monitor mode. If a failure is found, replace the primary transfer roller disengagement switch assembly. Execute the primary transfer roller engagement/disengagement drive test in the actuator drive mode. If the primary transfer roller does not perform engagement/disengagement, replace the fixing drive unit.

Error code:	E079-0001
Description:	The home position of the outside heating roller is not detected. The outside heating roller home position sensor does not go off. The HP sensor does not turn on within 5 sec after the start of an HP search.
Remedy:	Turn off and then on the main power.

Error code:	E079-0002
Description:	The home position of the outside heating roller is not detected. The outside heating roller home position sensor does not go off. If there is an open circuit in the home position sensor of the outside heating roller home position sensor, the state of the sensor will be identified as being ON. An error will be identified if the sensor fails to go off when it is at a point where it must normally go on and the outside heating roller shift motor is driven.
Remedy:	Turn off and then on the main power.

Error code:	E100-0001
Description:	Error detection on any of scanner motor, laser unit, and BD detection at scanner area.
Causes:	Magenta optical assembly failure
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board.

Error code:	E100-0002
Description:	Optical assembly error (Laser)
Causes:	Cyan optical assembly failure
Remedy:	Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit.

Error code:	E110-0001
Description:	Optical assembly error (Scanner motor)
Causes:	Optical assembly error (Scanner motor rotation failure)
Remedy:	Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit.

Error code:	E110-0002
Description:	Error in first artificial BD adjustment
Causes:	Primary pseudo BD correction

Error code:	E110-0003
Description:	There is a scanner motor error. The FG signal is not detected while the polygon scanner is rotating stably.
Remedy:	Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power.

Error code:	E197-0002
Description:	Firmware error
Causes:	Unknown engine firmware error
Remedy:	1. Turn OFF and then ON the power. 2. Update firmware. 3. Replace the DC Controller PCB.

Error code:	E197-0003
Description:	There is an error in the communication with the fixing feed PCB. Following the end of initialization of the communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously.
Remedy:	Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power.

Error code:	E197-0004
Description:	There is an error in the communication with the fixing feed PCB. At the start of drum initial multiple rotation, there is no signal indicating the start of 24V in the fixing assembly in the communication between the DC controller and the fixing/feeding unit.
Remedy:	Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power.

Error code:	E202-0001
Description:	Reader HP sensor fault
Causes:	Reader HP outward fault The CCD unit moves backward, but does not move to the home position.
Remedy:	- Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit.

Error code:	E202-0002
Description:	Contact Sensor HP error, Failure in return
Causes:	Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position.
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board.

Error code:	E225-0001
Description:	Light intensity of a lamp is less or equal to the criteria
Causes:	When the light intensity is at the reference level or below at shading.
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board.

Error code:	E227-0001
Description:	Reader unit power supply error When the 24 V port is OFF when the power is turned ON.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0002
Description:	Reader unit power supply error When the 24 V port is OFF when a job is started.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0003
Description:	Reader unit power supply error When the 24 V port is OFF when a job is finished.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0004
Description:	Reader unit power supply error When the 24 V port is OFF during load drive.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E240-0000
Description:	Error in communication between main controller and DC controller Serial communication error
Causes:	The main controller PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check the connector connections. Check the DC controller PCB (MAISY). Replace the No.1 main controller circuit.

Error code:	E246-0001
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E246-0002
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E246-0003
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E246-0004
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E247-0001
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E248-0000
Description:	There is an error in the EEPROM. At time of start-up, a check error has occurred on the SRAM board
Remedy:	Turn off the main power, and check the SRAM board; then, as necessary, replace the SRAM board, and turn on the main power.

Error code:	E248-0001
Description:	EEPROM access error
Causes:	Error at EEPROM power-on EEPROM data cannot be read at power-on.
Remedy:	Replace reader unit.

Error code:	E248-0002
Description:	EEPROM access error
Causes:	Error in EEPROM writing EEPROM writing cannot be performed.
Remedy:	Replace reader unit.

Error code:	E248-0003
Description:	EEPROM access error
Causes:	Error in EEPROM reading after writing EEPROM reading cannot be performed after writing is performed.
Remedy:	Replace reader unit.

Error code:	E315-000E
Description:	codex error An error has occurred in the course of software decoding.

Error code:	E350-0000
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E350-0001
Description:	Fault in the soft ID PCB/function An error has occurred in the course of full data read operation on the soft ID PCB.
Remedy:	Turn off the main power, and check the connection of the soft ID PCB. If the remedy fails, replace the soft ID PCB.

Error code:	E350-0002
Description:	Fault in the soft ID PCB/function The value of the check sum area of all data read from the soft ID PCB and the result of checksum computation do not match.
Remedy:	Turn off the main power, and replace the soft ID PCB. If the remedy fails, replace the soft ID PCB.

Error code:	E350-0003
Description:	Fault in the soft ID PCB/function The values in the soft ID check sum area of FRAM, SRAM1, and SRAM2 and the result of a check sum computation differ.
Remedy:	Turn off the main power, and check the connection of the soft ID PCB. If the remedy fails, replace the soft ID PCB.

Error code:	E350-3000
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E351-0000
Description:	Main controller PCB fault
Causes:	Internal error of the main controller PCB Cause Main controller PCB fault.
Remedy:	- Check the connection of main controller PCB. - Replace main controller PCB.

Error code:	E354-0001
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E354-0002
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E355-0001
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E400-0001
Description:	Feeder communication error Checksum error
Remedy:	Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub).

Error code:	E400-0002
Description:	Feeder communication error Reception status error
Remedy:	Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub).

Error code:	E400-0003
Description:	Feeder communication error Reception interrupt error
Remedy:	Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub).

Error code:	E413-0001
Description:	Pressure motor trouble Pressure HP sensor OPEN
Remedy:	Replace the pressure motor.

Error code:	E413-0002
Description:	Pressure motor trouble Pressure HP sensor CLOSE
Remedy:	Replace the pressure motor.

Error code:	E490-0001
Description:	Wrong model error When the feeder of another model has been detected
Remedy:	Connect the feeder for this unit.

Error code:	E500-0001
Description:	Finisher communication error Data communication could not be performed normally. It has been retried three times in vain.
Remedy:	- Check the connectors of the finisher controller PCB and DC controller PCB for normal connection. - Replace the finisher controller PCB. - Replace the DC controller PCB.

Error code:	E503-0002
Description:	Saddle communication error When communication with the saddle stitcher is interrupted
Remedy:	- Check the connections between the saddle stitcher controller PCB and finisher controller PCB. - Replace the saddle stitcher controller PCB and finisher controller PCB.

Error code:	E503-0003
Description:	There is an error in the communication within the finisher (finisher R1/R2). finisher-to-punch unit communication error
Causes:	A communication error has been detected.
Remedy:	Check the connection between the Punch controller PCB and the finisher controller PCB.

Error code:	E505-0001
Description:	Finisher backup memory error When the checksum value calculated by the CPU differs from the checksum values of the data held inside the RAM
Causes:	The backup RAM is faulty.
Remedy:	Replace the finisher controller PCB.

Error code:	E505-0002
Description:	Finisher backup memory error When the verify processing is not completed even after 2000 ms have elapsed during data writing
Causes:	The EEPROM is faulty. The finisher controller PCB is faulty. The puncher driver PCB is faulty.
Remedy:	Replace the finisher controller PCB.

Error code:	E514-8001
Description:	Bundling (forward rotation direction) error When the trailing edge fails to leave the trailing edge assist home position even when the trailing edge assist motor has been driven for 3 sec.
Remedy:	Replace the trailing edge assist motor (M109) and trailing edge assist home position sensor (PI109).

Error code:	E514-8002
Description:	Bundling (forward rotation direction) error When the trailing edge fails to return to the trailing edge assist home position even when the trailing edge assist motor has been driven for 3 sec.
Remedy:	Replace the trailing edge assist motor (M109) and trailing edge assist home position sensor (PI109).

Error code:	E519-0002
Description:	There is an error in the gear change motor (finisher R1/R2). The home position sensor does not go on within a specific period of time after the gear change motor has started to rotate.
Remedy:	1) Check the gear change home position sensor. Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor. Is the wiring normal? 3) Check the gear change mechanism. Is there a fault? 4) Try replacing the gear change motor. Is the problem corrected?

Error code:	E519-8001
Description:	There is an error in the gear change motor (finisher R1/R2). The home position sensor does not go off within a specific period of time after the gear change motor has started to rotate.
Remedy:	1) Check the gear change home position sensor. Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor. Is the wiring normal? 3) Check the gear change mechanism. Is there a fault? 4) Try replacing the gear change motor. Is the problem corrected?

Error code:	E530-8001
Description:	Alignment error When the alignment plate fails to leave the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec.
Remedy:	Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106).

Error code:	E530-8002
Description:	Alignment error When the alignment plate fails to return to the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec.
Remedy:	Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106).

Error code:	E531-0001
Description:	- Staple unit failure - Staple HP sensor failure - Finisher controller PCB failure - The staple home position was not left when 400 ms have lapsed since start of staple operation.
Causes:	The stapler motor (M6) is faulty. The stapler home position sensor detecting switch (MS7) is faulty.
Remedy:	- Check the connector of the staple unit. - Replace the staple unit. - Replace the finisher controller PCB.

Error code:	E531-0002
Description:	- Staple unit failure - Staple HP sensor failure - Finisher controller PCB failure - The staple home position had been left once, but it was not reached again when 400 ms have lapsed since start of staple operation. In addition, the staple home position could not be reached by performing reverse operation for 400 ms.
Causes:	The stapler motor (M6) is faulty. The stapler home position sensor detecting switch (MS7) is faulty.
Remedy:	- Check the connector of the staple unit. - Replace the staple unit. - Replace the finisher controller PCB.

Error code:	E532-8001
Description:	There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go off within a specific period of time after the stapler shift motor has started to rotate.
Remedy:	1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected?

Error code:	E532-8002
Description:	There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go on within a specific period of time after the stapler shift motor has started to rotate.
Remedy:	1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected?

Error code:	E535-0003
Description:	There is an error in the staple swing mechanism. (finisher R1/R2) There is an error in relation to an hazardous area..
Causes:	The delivery motor (M2) is faulty. The swing guide closed detecting switch 2 (MS6) is faulty.
Remedy:	1) Check the swing home position sensor. Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor. Is the wiring normal? 3) Check the swing mechanism. Is there a fault? 4) Try replacing the swing motor. Is the problem corrected?

Error code:	E535-8001
Description:	Oscillation error When the stapler fails to leave the oscillation home position even though the oscillator motor was driven for 3 sec.
Remedy:	Replace the oscillator motor (M106) and oscillation home position sensor (PI105).

Error code:	E535-8002
Description:	Oscillation error Occurs when the oscillation guide close switch fails to be set to ON even when the oscillator motor is run in the reverse direction for 1 sec.
Remedy:	Replace the oscillator motor (M106) and oscillation home position sensor (PI105).

Error code:	E537-8001
Description:	Front alignment error When the alignment plate fails to leave the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec.
Remedy:	Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107).

Error code:	E537-8002
Description:	Front alignment error When the alignment plate fails to return to the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec.
Remedy:	Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107).

Error code:	E540-8001
Description:	Tray up/down error - When the tray fails to return to the home position even when the 1st tray shift motor has been driven for 20 sec. - When the tray fails to move to another area even when the 1st tray shift motor has been driven for 4 sec.
Remedy:	- Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107)

Error code:	E540-8002
Description:	Tray up/down error When a danger area is reached before the sheet level is detected by the 1st tray sheet level detection sensor during the sheet level detection operation - When a discontinuous area was detected during the tray operation
Remedy:	- Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107)

Error code:	E540-8003
Description:	Tray up/down error When the input of the clock signal could not be detected within 0.2 sec. during the operation of the 1st tray shift motor
Remedy:	- Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107)

Error code:	E542-0003
Description:	- Optional tray motor or finisher controller PCB failure - Optional tray HP sensor failure - Optional tray clock sensor failure - Optional tray shift motor load failure - The optional tray was moved upward, but it did not reach the HP sensor within 3000 ms.
Remedy:	- Check the connector of the optional tray HP sensor. - Check the connector of the optional tray clock sensor. - Check the connector of the optional tray shift motor. - Replace the optional tray HP sensor. - Replace the optional tray clock sensor. - Replace the optional tray shift motor. - Replace the finisher controller PCB.

Error code:	E542-8001
Description:	Tray shift error When the tray fails to return to the home position even when the 2nd tray shift motor has been driven for 20 sec. - When the tray fails to move to another area even when the 2nd tray shift motor has been driven for 4 sec.
Remedy:	- Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108).

Error code:	E542-8002
Description:	Tray shift error - When the upper limit area is reached before the sheet level is detected by the 2nd tray sheet level detection sensor 1 during a sheet level detection operation - When a discontinuous area was detected during the tray operation - When the fact that the area ahead of the 2nd tray sheet level detection sensor 2 has been reached is detected before the sheet level is detected by the 2nd tray sheet level detection sensor 2 during an escape operation
Remedy:	- Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108).

Error code:	E584-0002
Description:	- Shutter drive motor or finisher controller PCB failure - Shutter open detection sensor failure - Shutter clutch failure - The shutter open sensor did not turn off when 1000 ms have lapsed since the shutter unit had performed close operation, resulting in incomplete close operation.
Causes:	The feed motor (M1) is faulty. The shutter open sensor (PI5) is faulty.
Remedy:	- Check the connector of the shutter open sensor. - Check the connector of the shutter clutch. - Check the connector of the shutter motor. - Replace the shutter open sensor. - Replace the shutter clutch. - Replace the shutter drive motor. - Replace the finisher controller PCB.

Error code:	E584-8001
Description:	Tray unit trouble When the shutter fails to leave the shutter home position even when the binding motor has been driven for 3 sec.
Remedy:	- Check the shutter home position sensor connectors. - Replace the shutter home position sensor. - Replace the shutter open/close clutch (CL101). - Replace the binding bottom roller clutch (CL102). - Replace the binding motor (M102).

Error code:	E590-8001
Description:	When the puncher cannot detect the punch home position sensor even when the punch motor is driven for 200 ms
Remedy:	- Check the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch motor (M61).

Error code:	E590-8002
Description:	When the puncher cannot detect the punch home position sensor after motor drive has stopped during the initial operation of the punch motor
Remedy:	- Check the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch motor (M61).

Error code:	E591-8001
Description:	When the light sensing voltage is less than 3.0 V even though the lightemitting duty ratio of the waste full detection sensor has been set to more than 66%
Remedy:	- Check the waste full detection sensor (LED6, PTR6) connectors. - Replace the waste full detection sensors (LED6, PTR6).

Error code:	E591-8002
Description:	When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of the waste full detection sensor has been set to 0%
Remedy:	- Check the waste full detection sensor (LED6, PTR6) connectors. - Replace the waste full detection sensors (LED6, PTR6).

Error code:	E592-8001
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of the sheet trailing edge sensor has been set to more than 66%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-8002
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of the sheet trailing edge sensor has been set to 0%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-8003
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of side registration sensor 1 (LED1, PTR1) has been set to more than 66%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-8004
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of side registration sensor 1 (LED1, PTR1) has been set to 0%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-8005
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of side registration sensor 2 (LED2, PTR2) has been set to more than 66%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-8006
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of side registration sensor 2 (LED2, PTR2) has been set to 0%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-8007
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of side registration sensor 3 (LED3, PTR3) has been set to more than 66%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-8008
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of side registration sensor 3 (LED3, PTR3) has been set to 0%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-8009
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is less than 2.5 V even though the lightemitting duty ratio of side registration sensor 4 (LED4, PTR4) has been set to more than 66%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E592-800A
Description:	Sheet trailing edge, side registration sensor error When the light sensing voltage is more than 2.0 V even though the lightemitting duty ratio of side registration sensor 4 (LED4, PTR4) has been set to 0%
Remedy:	- Check the sheet trailing edge sensor (LED5, PTR5) and side registration sensor (LED1-4, PTR1-4) connectors. - Replace the sheet trailing edge sensor (LED5, PTR5) and side registration sensors (LED1-4, PTR1-4).

Error code:	E593-8001
Description:	Side registration initializing error When the side registration fails to leave the side registration home position sensor position even when the punch slide unit is moved 9 mm during the initial operation of the side registration motor
Remedy:	- Check the side registration home position sensor (P161) connectors. - Replace the side registration home position sensor (P161). - Replace the side registration motor (M62).

Error code:	E593-8002
Description:	Side registration initializing error When the side registration fails to return to the side registration home position sensor position even when the punch slide unit is moved 37 mm during the initial operation of the side registration motor
Remedy:	- Check the side registration home position sensor (P161) connectors. - Replace the side registration home position sensor (P161). - Replace the side registration motor (M62).

Error code:	E5F0-0001
Description:	There is an error in saddle paper positioning. The paper positioning plate home position sensor does not turn on when the paper positioning plate motor has been driven for 1.33 sec. The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty.
Causes:	The positioning plate motor (M4S) is faulty. The power positioning plate home position sensor (PI7S) is faulty.
Remedy:	Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S).

Error code:	E5F0-0002
Description:	There is an error in saddle paper positioning. The paper positioning plate home position sensor does not turn off when the paper positioning plate motor has been driven for 1 sec. The paper positioning plate motor (M4S) or the paper positioning plate home position sensor (PI7S) is faulty.
Causes:	The positioning plate motor (M4S) is faulty. The power positioning plate home position sensor (PI7S) is faulty.
Remedy:	Check the paper positioning plate motor (M4S) /paper positioning plate home position sensor (PI7S).

Error code:	E5F1-0001
Description:	There is an error in saddle paper folding. The number of detection pulses of the paper folding motor clock sensor is lower than specified. The paper folding home position sensor or the paper folding motor clock sensor (P14S) is faulty.
Causes:	The folding motor (M2S) is faulty. The folding motor clock sensor (PI4S) is faulty.
Remedy:	Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S).

Error code:	E5F1-0002
Description:	There is an error in saddle paper folding. The state of the paper folding home position sensor does not change when the paper folding motor has been driven for 3 sec. The paper folding motor (M2S) or the paper folding motor clock sensor (P14S) is faulty.
Causes:	The folding roller home position sensor (PI12) is faulty. The stapler/folder motor (M7) is faulty. The stapler/folder clock sensor (PI14) is faulty. The finisher controller PCB is faulty.
Remedy:	Check the paper folding motor (M2S) /paper folding motor clock sensor (PI4S).

Error code:	E5F2-0001
Description:	There is an error in the saddle guide. The guide home position sensor does not turn on when the guide motor has been driven for 0.45 sec. The guide motor (M3S) or the guide home position sensor (PI3S) is faulty.
Causes:	The guide motor (M3S) is faulty. The guide home position sensor (PI13S) is faulty.
Remedy:	Check the guide motor (M3S) /guide home position sensor (PI13S).

Error code:	E5F2-0002
Description:	There is an error in the saddle guide. The guide home position sensor doest not turn off when the guide motor has been driven for 1 sec. The guide motor (M3S) or the guide home position sensor (PI3S) is faulty.
Causes:	The guide motor (M3S) is faulty. The guide home position sensor (PI13S) is faulty.
Remedy:	Check the guide motor (M3S) /guide home position sensor (PI13S).

Error code:	E5F3-0001
Description:	There is an error in saddle alignment. The aligning plate home position sensors does not turn on when the alignment motor has been driven for 05. sec (during initialization, 1.67 sec). The alignment motor (M5S) or the aligning plate home position sensor (PI5S) is faulty.
Causes:	The alignment motor (M5S) is faulty. The alignment plate home position sensor (PI5S) is faulty.
Remedy:	Check the alignment motor (M5S) /aligning plate home position sensor (PI5S).

Error code:	E5F3-0002
Description:	There is an error in saddle alignment. The alignment plate home position sensor does not turn off when the alignment motor has been driven for 1 sec. The alignment motor (M5S) for the alignment plate home position sensor (PI5S) is faulty.
Causes:	The alignment motor (M5S) is faulty. The alignment plate home position sensor (PI5S) is faulty.
Remedy:	Check the alignment motor (M5S) /aligning plate home position sensor (PI5S).

Error code:	E5F4-0001
Description:	There is an error in saddle rear sampling. The stitching home position sensor does not turn on when the stapler motor (rear) is rotated in reverse for 0.5 sec or more. The switch motor (rear, M65) or the stitching home position sensor (rear, MS5S) is faulty.
Causes:	The stitch motor (rear, M6S) is faulty. The stitching home position switch (rear, PS2S) is faulty.
Remedy:	Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S)

Error code:	E5F4-0002
Description:	There is an error in saddle rear sampling. The stitching home position sensor does not turn off when the switch motor (rear) is reverse for 0.5 sec or more. The switch motor (rear, M6S) or the stitching home position sensor (rear, MS5S) is faulty.
Causes:	The stitch motor (rear, M6S) is faulty. The stitching home position switch (rear, PS2S) is faulty.
Remedy:	Check he stitching motor (rear; M6S) /stitching home position sensor (rear; MS5S).

Error code:	E5F5-0001
Description:	There is an error in saddle front stapling. The stitching home position sensor does not turn on when the switch motor (front) is rotated in reverse for 0.5 sec or more. The stitch motor (front, M7S) or the stitching home position sensor (front, MS7S) is faulty.
Causes:	The stitching motor (front, M7S) is faulty. The stitching motor operating home position switch (front, PS4S) is faulty.
Remedy:	Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S).

Error code:	E5F5-0002
Description:	There is an error in saddle front stapling. The stitching home position sensor does not turn off when the switch motor (front) is rotated in normal direction for 0.5. The stitch motor (front, M7S) or the switching home position sensor (front, MS7S) is faulty.
Causes:	The stitching motor (front, M7S) is faulty. The stitching motor operating home position switch (front, PS4S) is faulty.
Remedy:	Check the stitching motor (front; M7S) /stitching home position sensor (front; MS7S).

Error code:	E5F6-8001
Description:	Saddle sheet push plate stapler error When the sheet push plate home position sensor fails to turn ON even when the sheet push plate motor has been run for at least 0.3 sec.
Remedy:	- Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S).

Error code:	E5F6-8002
Description:	Saddle sheet push plate stapler error When the sheet push plate home position sensor fails to turn OFF even when the sheet push plate motor has been run for at least 80 ms
Remedy:	- Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S).

Error code:	E5F6-8003
Description:	Saddle sheet push plate stapler error When the sheet push plate edge position sensor fails to turn OFF even when the sheet push plate motor has been run for at least 80 ms
Remedy:	- Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S).

Error code:	E5F6-8004
Description:	Saddle sheet push plate stapler error When the number of pulses detected by the sheet push plate motor clock sensor has dropped below the prescribed number
Remedy:	- Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S).

Error code:	E5F6-8005
Description:	Saddle sheet push plate stapler error When the sheet push plate edge position sensor fails to turn ON even when the sheet push plate motor has been run for at least 0.3 sec.
Remedy:	- Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S).

Error code:	E5F8-0001
Description:	There is an error in the saddle connector. The connector of the guide home position sensor is identified as being disconnected. The connector of the guide home position sensor (PI3S) is faulty.
Causes:	The guide home position sensor (PI13S) has a faulty connector.
Remedy:	Check the connectors of the guide home position sensor (PI13S). Check the connectors of the paper pushing plate home position sensor (PI4S).

Error code:	E5F8-0002
Description:	There is an error in the saddle connector. The connector of the paper pushing plate home position sensor is identified as being disconnected. The connector of the paper pushing plate home position sensor (PI14S) is faulty.
Causes:	The paper push-on plate home position sensor (PI14) has a faulty connector.
Remedy:	Check the connectors of the paper pushing plate leading edge position sensor (PI5S).

Error code:	E5F8-0003
Description:	There is an error in the saddle connector. The connector of the paper pushing plate leading edge position sensor is identified as being disconnected. The connector of the paper pushing plate leading edge sensor (PI15S) is faulty.
Causes:	The paper push-on plate leading edge sensor (PI15S) has a faulty connector.
Remedy:	Check the connectors of the paper pushing plate leading edge position sensor (PI5S).

Error code:	E5F9-0001
Description:	There is an error in the saddle switch. With any of the following sensor is identifying its respective cover a being closed, the inlet cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) Or, the front cover switch (MS2S) or the delivery cover switch (MS3S) is open. The inlet cover switch (MS1S), front cover switch (MS2S), or delivery cover switch (MS3S) is faulty.
Causes:	The inlet door open detecting switch (MS1S) is faulty. The inlet door sensor (PI9S) is faulty.
Remedy:	Check the inlet cover switch (MS1S)/front cover switch (MS2S)/delivery cover switch (MS3S).

Error code:	E5F9-0002
Description:	There is an error in the saddle switch. With any of the following sensor is identifying its respective cover as being closed, the front cove switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cove sensor (PI3S) The front cove switch (MS2S) or the delivery cover switch (MS3S) is faulty.
Causes:	The front door open detecting switch (MS2S) is faulty. The front door open sensor (PS2S) is faulty.
Remedy:	Check the front cover switch (MS2S)/delivery cover switch (MS3S).

Error code:	E5F9-0003
Description:	There is an error in the saddle switch. With any of the following sensors identifying its respective cover as being closed, the delivery cover switch is identified as being open for 1 sec or more after the start of the initial rotation of the machine or the start of printing: - inlet cover sensor (PI9S) - front cover open/closed sensor (PI2S) - delivery cover sensor (PI3S) - delivery cover switch (MS3S)
Causes:	The delivery door open detecting switch (MS3S) is faulty. The delivery door open sensor (PI3S) is faulty.
Remedy:	Check the delivery cover switch (MS3S).

Error code:	E602
Description:	Yellow TCR Sensor adjustment failure - TCR Sensor automatic adjustment does not function properly, failing to adjust to an appropriate value.
Causes:	• Photoconductor Unit /C • Photoconductor Unit /M • Photoconductor Unit /Y • Toner Supply Motor Y/M (M6) • Toner Supply Motor C/K (M7) • Mechanical Control Board (PWB-M) • Controller Board (PWB-P)
Remedy:	1 Clean the TCR Sensor window on the underside of the Photoconductor Unit if dirty - - 2 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23 3 Reinstall Photoconductor Unit - - 4 Change Photoconductor Unit - - 5 Change PWB-M - - 6 Change PWB-P

Error code:	E604-0000
Description:	Memory error
Causes:	Lack of memory capacity
Remedy:	Check the memory capacity inserted to each slot.

Error code:	E609-0008
Description:	Hard disk trouble When the HDD fails to reach the prescribed temperature within the prescribed period of time when it is started up
Remedy:	Replace with an HDD which is guaranteed to operate at low temperatures.

Error code:	E609-0009
Description:	Hard disk trouble When the HDD fails to reach the prescribed temperature when its operation is restored from the sleep mode
Remedy:	Replace with an HDD which is guaranteed to operate at low temperatures.

Error code:	E610
Description:	1st Image Transfer ATVC (color) failure - An abnormal average value is detected while performing the first image transfer ATVC of color.
Causes:	• Transfer Belt Unit • Transfer Roller • High Voltage Unit
Remedy:	1 Check if the Transfer Roller and Transfer Belt are dirty and correct as necessary. - - 2 Change High Voltage Unit - - 3 Change Transfer Belt Unit

Error code:	E674-0001
Description:	There is an error in the fax board. The fax board is detected, but communication is not possible.
Remedy:	Turn off the main power, and check the fax board and the main controller PCB; then, turn on the main power. If the machine fails to reset, replaced the fax board or the main controller PCB

Error code:	E677-0003
Description:	There is an external controller error. An error has been detected by a check on the configuration when the external controller is being started up.
Remedy:	Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external contro

Error code:	E677-0010
Description:	There is an external controller error. A controller for a non-Canon machine is connected.
Remedy:	Turn off the main power, and check the controller is an appropriate type, and check the cable; then turn on the main power. If the machine fails to reset, re-install the system software of the external controller.

Error code:	E677-0080
Description:	There is an external controller error. There is an error in the communication with the printer after the external controller has started up normally.
Causes:	The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty.
Remedy:	Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external controller.

Error code:	E710-0001
Description:	IPC initializing error When the ready status fails to be established within 3 sec. after the IPC chip started up
Causes:	The DC controller PCB is faulty. The reader controller PCB is faulty. The machine controller PCB is faulty.
Remedy:	Check the cable connections.

Error code:	E711-0002
Description:	There is an IPC communication error. An error has been detected 4 times or more within 1.5 sec after the communication has been interrupted between the finisher and the printer, and the machine does not reset.
Causes:	The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty.
Remedy:	Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to reset, check the connector between the finisher and the copier for poor contact; as necessary, replace the finisher controller/DC controller.

Error code:	E713-0001
Description:	There is a finisher communication error. There is an error in the IC used for communication by the sorter.
Remedy:	Turn off the main power switch, and check the wiring of the DC controller PCB and the finisher controller PCB, and check the 24V system fuse: then, turn on the main power switch. If the machine does not reset, replace the DC controller PCB/finisher controller PCB.

Error code:	E717-0001
Description:	Error in communication with NE controller When the NE controller which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Causes:	The wiring is faulty (short circuit, open circuit). The DA unit PCB is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the cable connections.

Error code:	E717-0002
Description:	Error in communication with NE controller When the IPC has a broken or disconnected wire or when an error has occurred where IPC communication cannot be recovered
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR.

Error code:	E719-0001
Description:	Error in communication with coin vendor/card reader When the coin vendor which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Causes:	The wiring is faulty (short circuit, open circuit). The Card Reader-C1 is faulty. The coin vendor is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the cable connections.

Error code:	E719-0002
Description:	Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.)
Causes:	Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.)
Remedy:	- Check the connection between the image processor PCB and serial PCB. - Check the connectors of the serial PCB and coin vendor for normal connection. - Replace the serial PCB. - Check the coin vendor. - Replace the image processor PCB.

Error code:	E719-0011
Description:	Error in communication with coin vendor/card reader When the card reader which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR

Error code:	E719-0012
Description:	Error in communication with coin vendor/card reader When a wire in the IPC cable connected with the card reader is broken or disconnected or when an error has occurred where IPC communication cannot be recovered
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR

Error code:	E730
Description:	PDL error
Remedy:	Turn the main power OFF and back ON. Check the OPEN interface board and cable connections. Replace the external controller. Replace the OPEN interface board. Replace the main controller PCB.

Error code:	E731
Description:	Stop jam at the original exit sensor: The trailing edge of the original does not pass the original exit sensor after its leading edge has reached this sensor
Causes:	Original exit sensor RADF board Perform the 05-3210 Roller Exit roller
Remedy:	1. Clean the exit roller and the exit intermediate roller if they are stained. 2. Is the original exit sensor working? (Perform the input check: 03-[FAX]ON/[7]/[E]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit sensor or the harnesses are open circuited. Correct if any. 4. Replace the original exit sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the exit roller and the exit intermediate roller if they are worn out.

Error code:	E732-0001
Description:	Scanner communication error
Causes:	Scanner communication error
Remedy:	1. Update the firmware. 2. Replace the Main Controller PCB.

Error code:	E732-9999
Description:	There is an error in reader communication. Although a printer model, the machine is identified as a reader unit at start-up. (A copier model is started up as a printer model when the RAM is initialized.)
Remedy:	Turn off and then on the main power.

Error code:	E733-0000
Description:	Erroneous communication between controller and printer Cannot communicate with the printer at startup.
Causes:	Printer communication error (communication error at initial communication and negotiation packet error)
Remedy:	- Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB.

Error code:	E733-0001
Description:	Printer communication error (Invalid communication after communication is established, Parity error)
Remedy:	Turn on the power again. Replace the DC controller PCB.

Error code:	E740-0002
Description:	Error detection on either Network Board or Mac address
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board.

Error code:	E743-0000
Description:	Error in main controller communication An error in reading of/writing to the Flash ROM in the Main Controller occurred.
Causes:	Software sequence error
Remedy:	1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB.

Error code:	E744
Description:	Stop jam at the original exit/reverse sensor
Causes:	Original exit/reverse sensor RADF board Perform the 05-3210 Roller Intermediate transport roller
Remedy:	1. Clean the exit/reverse intermediate roller if it is stained. 2. Is the original exit/reverse sensor working? (Perform input check: 03: [FAX]/ON/[5]/[B]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit/reverse sensor or the harnesses are open-circuited. Correct if this is the case. 4. Replace the original exit/reverse sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the exit/reverse intermediate roller, if it is worn out.

Error code:	E745
Description:	Jam not reaching the original exit/reverse sensor
Causes:	Original exit reverse sensor RADF board Perform the 05-3210 Roller
Remedy:	1. Clean the exit intermediate roller if it is stained. 2. Is the original exit/reverse sensor working? (Perform input check: 03: [FAX]/ON/[5]/[B]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit/reverse sensor or the harnesses are open-circuited. Correct if this is the case. 4. Replace the original exit/reverse sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the exit intermediate roller, if it is worn out.

Error code:	E746-0003
Description:	The accessories board is of the wrong type. At time of start-up, the UFR board is found to be of the wrong type. (A query is made to find out if the type is correct with reference to the engine ID.)
Remedy:	Replace it with a UFR board of the correct type.

Error code:	E746-0004
Description:	The accessories board is of the wrong type. At time of start-up, the scanner board is found to be of the wrong type. (A query is made to find out if the type is correct with reference to the engine ID.)
Remedy:	Replace it with a scanner board of the correct type.

Error code:	E747
Display:	E747
Description:	Optical Fan Motor error. When the lock signal is detected continuously for the predetermined time during fan rotation.
Causes:	• Fuser Fan Motor (M7) • PH Fan Motor (M8) • Suction Fan Motor (M13) • Ozone Fan Motor (M9) • PS Fan Motor (M6) • PU Fan Motor (M12)
Remedy:	1 Check the motor connector connection status, and correct if it is improper. 2 Check the load status of the fan section, and correct if it is improper. 3 Check the operation of M8. p115 PWB-A CNF2-A-1(REM) 5-G 4 Replace the PWB-A.

Error code:	E748
Description:	Internal cooling fan motor error. When the lock signal is detected continuously for the predetermined time during fan rotation.
Causes:	• Fuser Fan Motor (M7) • PH Fan Motor (M8) • Suction Fan Motor (M13) • Ozone Fan Motor (M9) • PS Fan Motor (M6) • PU Fan Motor (M12)
Remedy:	1 Check the motor connector connection status, and correct if it is improper. 2 Check the load status of the fan section, and correct if it is improper. 3 Check the operation of M12. p115 PWB-A CNF3-A-1(REM) 7-C 4 Replace the PWB-A.

Error code:	E749-0001
Description:	Instruction to restart accompanying change in product configuration When the existing BootROM has been replaced with the BootROM of a different kind (when a PDL option was installed, etc.)
Remedy:	Reset by turning the main power OFF and back ON.

Error code:	E800-0001
Description:	The interlock 24V mechanism of the fixing unit is identified as being off. With the door closed, the interlock 24V mechanism remains off for 500 msec.
Causes:	The electric system has an error. The DC controller PCB is faulty.
Remedy:	Turn off the main switch, and check the wiring of the DC controller PCB, check the fixing unit interlock, and check the 24V system fuse; then, turn on the interlock main switch.

Error code:	E804-0004
Description:	Controller Fan error Since the startup of the Controller Fan, the Fan was locked for a specified consecutive period of time.
Causes:	Power supply cooling fan does not rotate in the specified rotation speed. Cause: Problem in power supply cooling fan / DC controller PCB
Remedy:	1. Check power supply to the Controller Fan. 2. Replace the Controller Fan.

Error code:	E804-0007
Description:	There is any of the various types of fan errors. There is an error in the power supply cooling fan.
Remedy:	Turn off the main switch, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch.

Error code:	E805-0003
Description:	Fan failure
Causes:	Controller fan failure detected The controller fan does not rotate because some kind of failure occurred in it.
Remedy:	Replace the controller fan.

Error code:	E820-0002
Description:	There is an error in the process unit cooling fan. There is an error in the process unit fan.
Remedy:	Turn off the main switch, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main switch.

Error code:	E824-0000
Description:	There is an error in the primary charging suction/primary charging exhaust fan. There is an error in the primary charging suction mechanism.
Remedy:	Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch.

Error code:	E824-0001
Description:	There is an error in the primary charging suction/primary charging exhaust fan. There is an error in the primary exhaust fan.
Remedy:	Turn off the main switch, and check the wiring of the DC controller PCB and 2V system fuse; then, turn on the main switch.

Деталь:	SCALE, LINEAR
Парткод:	QC3-1880-000

Деталь:	SCALE, LINEAR
Парткод:	QC4-9427-000

Деталь:	SPRING, TENSION
Парткод:	QC4-9294-000

Деталь:	SUCTION FAN UNIT
Парткод:	QM4-2817-000

Деталь:	PLATEN SHUTTER DRIVE UNIT
Парткод:	QM4-2756-000

Деталь:	MOTOR, STEPPING DC 10W UNDER
Парткод:	QK1 -0440-000

Деталь:	PHOTOINTERRUPTER, GP1S173LCS0F
Парткод:	WG8-5849-000

Деталь:	COVER, FRONT DUCT, LEFT
Парткод:	QC4-9075-000

Деталь:	COVER, FRONT DUCT, RIGHT
Парткод:	QL2-6908-000

Деталь:	HARNESS, WIRE, TANK COVER L
Парткод:	QM7-3631-000

Деталь:	LUBE, FLOIL G-5000H, GREASE
Парткод:	FY9-6022-000

Деталь:	MOTOR, UNDER 10W, DC
Парткод:	QK1-0550-000

Деталь:	PHOTO-INTERRUPTER, SG2481
Парткод:	WG8-5836-000

Деталь:	HARNESS, WIRE, CUTTER, LEFT
Парткод:	QM7-3617-000

Деталь:	HARNESS, WIRE, CUTTER, RIGHT
Парткод:	QM7-3618-000

Деталь:	M/C HOLDER UNIT
Парткод:	QM4-2785-000

Деталь:	ABSORBER, INK
Парткод:	QC4-9049-000

Деталь:	ABSORBER, INK
Парткод:	QC4-9050-000

Деталь:	WASTE INK BOX UNIT
Парткод:	QM4-2753-000

Деталь:	PAPER GUIDE ROLLER UNIT
Парткод:	QM4-2766-000

Деталь:	ROLLER, LIMIT, RIGHT
Парткод:	QC4-9192-000

Деталь:	ROLL HOLDER UNIT (L)
Парткод:	QM4-2878-000

Деталь:	ROLL HOLDER UNIT (R)
Парткод:	QM4-2879-000

Деталь:	GEAR, LIFT, DOUBLE B
Парткод:	QC4-9039-000

Деталь:	GEAR, LIFT, DOUBLE C
Парткод:	QC4-9040-000

Деталь:	INK TANK ROM PCB UNIT
Парткод:	QM3-1355-010

Деталь:	INK SUPPLY MOUNT UNIT (L)
Парткод:	QM3-5910-010

Деталь:	INK SUPPLY MOUNT UNIT (R)
Парткод:	QM3-5861-010

Деталь:	HEAD MANAGEMENT SENSOR UNIT
Парткод:	QM4-3246-000

Canon imageRUNNER 6800CN

Общие характеристики

Тип устройства

Копир

Сканер

Область применения

Размещение

Цветность печати

Факс

Печать фотографий

Телефон

Макс. формат

Тип

Технология печати

Принтер

Прямая печать

Печать без полей

Пигментные чернила

Двусторонняя печать

Время разогрева

Макс, разрешение для ч/б печати

Скорость ч/б печати

Скорость цветной печати

Время выхода первого отпечатка

Копир

Макс, количество копий за цикл

Шаг масштабирования

Время выхода первой копии

Значение масштаба

Макс, разрешение (ч/б)

Сканер

Тип сканера

Макс. формат оригинала

Оттенки серого

Макс, размер сканирования

Расходные материалы

Количество картриджей

Печать на:

Плотность бумаги

Телефон

Caller ID

Беспроводная трубка

АОН

Спикерфон

Стандарт DECT

Автоответчик

Проводная трубка

Языки управления

Лотки

Подача бумаги

Вывод бумаги

Финишер

Сортер

Сортировка со сдвигом

Степлер

Брошюровщик

Интерфейсы

USB

Ethernet (RJ-45)

Веб-интерфейс

Версия USB

LPT

RS-232

Устройство для чтения карт памяти

Wi-Fi

Bluetooth

FireWire (IEEE 1394)

Инфракрасный порт

Память/Процессор

Объем памяти

Емкость жесткого диска

Дополнительная информация

Мин. системные требования

Экран

Поддержка ОС

Потребляемая мощность

Габариты

Вес

Глубина

Ширина

Деталь:	HARNESS, WIRE, TANK, LEFT
Парткод:	QM3-4600-000

Деталь:	HARNESS, WIRE, TANK (R)
Парткод:	QM3-4601-000

Деталь:	INK SUPPLY TANK UNIT (R)
Парткод:	QM3-5954-000

Деталь:	INK SUPPLY TANK UNIT (L)
Парткод:	QM3-5955-000

Деталь:	TAPE, MOUNT, JOINT, INK
Парткод:	QC3-1939-000

Деталь:	INK TANK ROM PCB UNIT (L)
Парткод:	QM7-3608-000

Деталь:	INK TANK ROM PCB UNIT (R)
Парткод:	QM7-3609-000

Деталь:	HARNESS, WIRE, TANK (L)
Парткод:	QM7-3632-000

Деталь:	HARNESS, WIRE, INK SENSOR (L)
Парткод:	QM7-3640-000

Деталь:	HARNESS, WIRE, INK SENSOR (R)
Парткод:	QM7-3641-000