Canon imageRUNNER Advance 8295 PRO

Общие характеристики
Макс. формат	A3
Цветность печати
Тип	лазерный/светодиодный
Технология печати	лазерная
Размещение	напольный
Копир
Сканер
Тип устройства	МФУ
Печать фотографий
Телефон
Факс
Время разогрева	60
Прямая печать
Двусторонняя печать
Пигментные чернила
Печать без полей
Макс, разрешение для ч/б печати
По X	1 200
По Y	1 200
Скорость ч/б печати
A4	95
A3	50
Макс, количество копий за цикл	9 999
Время выхода первой копии	2,7
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По Y	1 200
По X	1 200
По Y	600
Макс. формат оригинала	A3
Емкость устройства автоподачи оригиналов	300
Тип сканера	планшетный/протяжный
Оттенки серого	256
Стандарт TWAIN
Отправка изображения по e-mail
Стандарт WIA
Слайд-адаптер
Устройство автоподачи оригиналов	двустороннее
Макс, размер сканирования
По Y	432
По X	305
Разрешение сканера
По Х	600
Скорость сканирования
Ч/б	120
Цветн,	85
Количество картриджей	1
Ресурс ч/б картриджа/тонера	56 000
Печать на:
Глянцевой бумаге
Матовой бумаге
Этикетках
Карточках
Конвертах
Фотобумаге
Рулоне
CD/DVD
Пленках
Плотность бумаги
Максимальная	256
Минимальная	52
PC Fax
Цветной
Caller ID
Спикерфон
Автоответчик
Беспроводная трубка
АОН
Стандарт DECT
Проводная трубка
Языки управления
PostScript	опционально
PCL 6
PCL 5e
PostScript 3
PDF
PCL 5c
PostScript 2
PPDS
Количество установленных шрифтов
PCL	93
PostScript	136
Емкость лотка ручной подачи	100
Подача бумаги
Стандартная	4 200
Максимальная	7 700
Вывод бумаги
Максимальный	4 000
Стандартный	250
Сортировка со сдвигом
Брошюровщик
Степлер
Сортер
Электронная сортировка
Версия USB	2,0
Ethernet (RJ-45)
Веб-интерфейс
USB
Bluetooth
LPT
AirPrint
Инфракрасный порт
RS-232
Устройство для чтения карт памяти
FireWire (IEEE 1394)
Wi-Fi
Wi-Fi 802.11n
Макс, объем памяти	1 536
Емкость жесткого диска	160
Объем памяти	1 536
Частота процессора	1 800
Экран
Работа от аккумулятора
Диагональ дисплея	10,4
Поддержка ОС
Mac OS
Linux
Windows
DOS
Потребляемая мощность
При работе	2 400
В режиме ожидания	244
Уровень шума
В режиме ожидания	36
При работе	61
Высота	1 252
Ширина	1 170
Вес	242
Глубина	770

Error code:	E000-0001
Description:	Fixing fault
Causes:	After the fixing heater has gone on, the reading of the main thermistor is not 50 deg C within about 1.5 sec. Cause The fixing film unit is faulty. The engine controller PCB is faulty.
Remedy:	- Replace the fixing film unit. - Replace the engine controller PCB.

Error code:	E000-0002
Description:	Fixing Assembly low temperature error. Temperature of the Fixing Main Thermistor (THM1) does not reach 10 degC although 35 seconds have passed after starting the Fixing Roller temperature control.
Remedy:	1. Check the connection of the Fixing Assembly. (Connection error of the Drawer, connector disconnection, open circuit) -> Replace the Heater Assembly. 2. Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10) (connector disconnection, open circuit, the caught cable). 3. Replace the Fixing Power Supply PCB (PCB10). 4. Replace the Main Driver PCB (PCB2). 5. Replace the DC Controller PCB (PCB1).

Error code:	E000-0010
Description:	At power-on, the rise in the temperature of the fixing assembly is not high enough. The main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4) has an open circuit or poor contact. The AC drive PCB or the DC controller PCB is faulty. After power-on, the temperature does not reach 50 deg C within 300 sec.
Remedy:	Check for an open circuit and poor contact in the main thermistor, thermal switch, and heater; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E001-0002
Description:	Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 1 has detected a high temperature (ASIC detection)
Causes:	The fixing film unit is faulty (i.e., the thermistor has a short circuit). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service move: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR.

Error code:	E001-0003
Description:	Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 2 has detected a high temperature (ASIC detection)
Remedy:	Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR.

Error code:	E001-0004
Description:	Abnormal high temperature in fixing
Causes:	The sub thermistor 2 detected a temperature exceeding a specified temperature
Remedy:	Replace the fixing assembly. Replace the DC controller PCB.

Error code:	E001-0010
Description:	Abnormality of the fixing unit A break in the end thermistor The status that A/D of the contact thermistor case is FFh continues for 500msec
Remedy:	Check on connection of the thermistor, Replace the fixing unit To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR

Error code:	E002-0001
Description:	The rise in temperature of the fixing assembly is faulty. The reading of the main thermistor does not reach 150 deg C within 2 min 30 sec after it has exceeded 100 deg C.
Remedy:	- Check if the connector (J505) of the DC controller PCB is mounted properly and also check if the connector of the fixing assembly is mounted properly. - Check the wiring between the thermistor and the DC controller. -Check if the main thermistor is mounted properly and also check if there is no contamination. - Replace the main thermistor. - Replace the fixing heater. - Replace the AC driver PCB. - Replace the DC controller PCB. Caution You must clear the error in service mode (COPIER>FUNCTION>CLEAR>ERR).

Error code:	E002-0010
Description:	The rise in the temperature of the fixing assembly is not enough. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3), thermal switch (TP1, TP2, TP3), or heater (H1, H2, H3, H4). The AC driver PCB or the DC controller PCB has a fault. The temperature of the fixing roller reaches 80 deg C, but drops below 50 deg C.
Remedy:	Check the main thermistor, thermal switch, and heater for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E003-0000
Description:	Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation.
Causes:	The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater.
Remedy:	- Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB.

Error code:	E003-0010
Description:	The fixing temperature is too low after a standby state. The power has been turned off and then on without clearing the error.
Remedy:	- Clear the error in service mode (COPIER>FUNCTION>CLEAR>ERR).

Error code:	E004-0010
Description:	There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. The fixing roller thermistor has an open circuit.
Remedy:	Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E004-0102
Description:	Fixing Power Supply error. Fixing current error.
Remedy:	Replace the Fixing Power Supply PCB (PCB10). Replace the Main Driver PCB (PCB2).

Error code:	E004-0205
Description:	Fixing unit protection circuit trouble Thermistor temperature difference error (combination unknown)
Remedy:	Replace the fixing belt unit. Replace the DC controller PCB 2 (MAISY).

Error code:	E005-0000
Description:	There is an error in the take-up mechanism of the web. The web of the fixing assembly has been fully taken up. After the web sensor has detected an off state, the count has exceeded 3000. The web length sensor (PS20) is faulty. The DC controller PCB is faulty.
Remedy:	Reset in service mode: COPIER>FUNCTION>CLEAR>ERR. If you have replaced the web, reset the reading in the following, and turn off and then on the power: COPIER>COUNTER>DRBL-1>FIX-WEB.

Error code:	E005-0001
Description:	Error in Fixing Cleaning Web Drive Solenoid connection. Connection of the Fixing Cleaning Web Drive Solenoid (SL9) is not detected when the power is turned ON.
Remedy:	1. Check the connection of the Connector. 2. Replace the Fixing Cleaning Web Drive Solenoid (SL9).

Error code:	E005-0010
Description:	There is an error in the take-up mechanism of the web. The drive solenoid of the fixing assembly is not connected.
Remedy:	Check the drive solenoid of the fixing web for disconnection; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E012-0001
Description:	Error in ITB motor activation.
Causes:	If the ITB motor speed detection signal comes off the specified cycle after it turned once to the specified cycle. Cause Failure in ITB motor, failure in DC controller PCB.
Remedy:	- Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB

Error code:	E013-0001
Description:	There is clogging by waste toner. There is a waste toner full error. the soft counter reading is 250000 or higher.
Causes:	The waste toner feedscrew has locked. The waste toner feed motor is faulty. The transfer high-voltage PCB is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check the amount of waste toner; then, turn off and then on the main power.

Error code:	E013-0002
Description:	There is clogging by waste toner. There is a waste toner feedscrew error. The output of the waste toner lock detecting switch (SW14) is `1` for more than 1 sec.
Causes:	The waste toner feedscrew has locked. The waste toner feed motor is faulty. The transfer high-voltage PCB is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check the developing motor; then, turn off and then on the main power.

Error code:	E014-0001
Description:	Fixing motor failure
Causes:	Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached.
Remedy:	Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor.

Error code:	E017-0001
Description:	ETB disengagement error. Disengagement of the ETB is not completed within the specified period of time.
Remedy:	1. Check the connection of the ETB Disengage Sensor (PS56). Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver PCB (PCB4)) 2. Check the connection of the Duplex Feed Left Motor (M19). Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4)) 3. Replace the ETB Disengage Sensor (PS56). 4. Replace the Duplex Feed Left Motor (M19). 5. Replace the Duplex Driver PCB (PCB4). 6. Replace the DC Controller PCB (PCB1).

Error code:	E017-0002
Description:	ETB engagement error. Engagement of the ETB is not completed within the specified period of time
Remedy:	1. Check the connection of the ETB Disengage Sensor (PS55). Sensor side: J2100, J3270, PCB side: J343 (Duplex Driver PCB (PCB4)) 2. Check the connection of the Duplex Feed Left Motor (M19). Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4)) 3. Replace the ETB Engage Sensor (PS55). 4. Replace the Duplex Feed Left Motor (M19). 5. Replace the Duplex Driver PCB (PCB4). 6. Replace the DC Controller PCB (PCB1).

Error code:	E017-0003
Description:	ETB HP error. Engagement of the ETB was not completed at initialization.
Remedy:	If this error occurs at installation, the ETB Disengage Member (Transfer Frame Stopper) may be left unremoved. Refer to the troubleshooting "Remedy to be implemented when the ETB Disengage Member (Transfer Frame Stopper) is left unremoved" in the Service Manual, and check whether the ETB Disengage Member is left unremoved or not and implement appropriate procedure. If this error occurs at times other than installation, follow the following steps to implement check and remedy. 1. Check the connection of the ETB Disengage Sensor (PS56). Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver PCB (PCB4)) 2. Check the connection of the Duplex Feed Left Motor (M19). Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex Driver PCB (PCB4)) 3. Replace the ETB Disengage Sensor (PS56). 4. Replace the Duplex Feed Left Motor (M19). 5. Replace the Duplex Driver PCB (PCB4). 6. Replace the DC Controller PCB (PCB1).

Error code:	E020-0000
Description:	Density sensor failure warning

Error code:	E020-0001
Description:	Error in Developing Toner Sensor connection detection. The connection detection port was OFF at power-on.
Remedy:	1. Check the connection of the Developing Toner Sensor (TS1). Sensor side: J2133, J3089 (relay), PCB side: J3088 (relay), J114 (Main Driver PCB (PCB2)) 2. Replace the Developing Toner Sensor (TS1). 3. Replace the Main Driver PCB (PCB2). 4. Replace the DC Controller PCB (PCB1).

Error code:	E020-0002
Description:	Error in Buffer Toner Sensor connection detection. The connection detection port was OFF at power-on.
Remedy:	1. Check the connection of the Buffer Toner Sensor (TS3). Sensor side: J2039, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 2. Replace the Buffer Toner Sensor (TS3). 3. Replace the Main Driver PCB (PCB2). 4. Replace the DC Controller PCB (PCB1).

Error code:	E020-0003
Description:	Error in the Toner Excess Supply Sensor connection detection. The connection detection port was OFF at power-on.
Remedy:	1. Check the connection of the Toner Excess Supply Sensor (TS2). Sensor side: J2038, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 2. Replace the Toner Excess Supply Sensor (TS2). 3. Replace the Main Driver PCB (PCB2). 4. Replace the DC Controller PCB (PCB1).

Error code:	E020-0004
Description:	Error in Magnet Roller Clutch connection detection. The connection detection port was OFF at power-on.
Remedy:	1. Check the connection of the Magnet Roller Clutch (CL5). Sensor side: J2036, J3124 (relay), J3090 (relay) PCB side: J3091(relay), J115 (Main Driver PCB (PCB2)) 2. Replace the Magnet Roller Clutch (CL5). 3. Replace the Main Driver PCB (PCB2). 4. Replace the DC Controller PCB (PCB1).

Error code:	E020-0020
Description:	Error in the developing assembly (toner fault: ATR error) Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Yellow ATR.
Remedy:	Clean the ATR sensor window. Check the mounting of the developing assembly. Check the ATR sensor open circuit. Replace the ATR sensor.

Error code:	E020-0021
Description:	Error in the developing assembly (toner fault: ATR error) Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Magenta ATR.
Remedy:	Clean the ATR sensor window. Check the mounting of the developing assembly. Check the ATR sensor open circuit. Replace the ATR sensor.

Error code:	E023-0001
Description:	The developing motor (M3) does not rotate normally. After motor start-up, a lock state is not detected for 1 sec or more.
Remedy:	Turn off and then on the main power.

Error code:	E023-0002
Description:	Error in Magnet Roller Clutch connection detection. Connection of the Magnet Roller Clutch (CL5) cannot be detected 5 times with 20 msec time interval.
Remedy:	1. Check the connection of the Magnet Roller Clutch (CL5). Sensor side: J2006, Main Driver PCB (PCB2) side: J109 2. Replace the Magnet Roller Clutch (CL5). 3. Replace the Main Driver PCB (PCB2). 4. Replace the DC Controller PCB (PCB1).

Error code:	E025-0001
Description:	There is an over-current in the hopper stirring motor (M23)or the black toner supply motor (M25). There is an overcurrent in the hopper stirring motor (M23).
Remedy:	Turn off and then on the main power.

Error code:	E027-0001
Description:	Toner Supply Motor error. Lock error of the Toner Supply Motor (M10).
Remedy:	1. Check the connection of the Connector. Motor side: J2037, Front side relay: J3080, Rear side relay: J3063, Main Driver PCB (PCB2) side: J117 2. Remove the Toner Container, and check if an error occurs. If an error does not occur, reinstall the Toner Container and check again. If an error occurs, check the driving area of connection point of the container. If an error occurs, go on to 3. 3. Replace the Toner Supply Motor (M10). 4. Replace the Main Driver PCB (PCB2). 5. Replace the DC Controller PCB (PCB1).

Error code:	E032-0001
Description:	NE controller counter operation failure When the counter function of the NE controller does not work
Causes:	The DA unit is faulty. The main controller PCB is faulty.
Remedy:	Check the cable connections.

Error code:	E041-0001
Description:	The fault was detected while the lifter was moving up. The deck lifter position sensor (PS104) does not detect the lifter within 60 sec after the deck lifter UP signal is generated. The output of the deck paper sensor (PS107) is ‘0’ when the output of the deck lifter position sensor (PS104) and that of the deck paper level sensor (PS108) are ‘1’.
Causes:	The deck lifter motor (M102) is faulty. The deck driver PCB is faulty. A connected device is faulty. The deck lifter position sensor (PS104) is faulty. The deck paper sensor (PS107) is faulty.
Remedy:	1. Check for displacement of the Lifter Wire of the Right Deck. 2. Check for hindrance to smooth movement of the Deck Base Plate of the Right Deck

Error code:	E041-0002
Description:	The fault was detected while the lifter was moving down. The deck lifter position sensor (PS104) does not detect the lifter within 60 sec after the deck lifter UP signal is generated. The output of the deck paper sensor (PS107) is ‘0’ when the output of the deck lifter position sensor (PS104) and that of the deck paper level sensor (PS108) are ‘1’.
Causes:	The deck lifter motor (M102) is faulty. The deck driver PCB is faulty. A connected device is faulty. The deck lifter position sensor (PS104) is faulty. The deck paper sensor (PS107) is faulty.
Remedy:	1. Check for displacement of the Lifter Wire of the Left Deck. 2. Check for hindrance to smooth movement of the Deck Base Plate of the Left Deck.

Error code:	E041-0003
Description:	Cassette 3 Lifter Motor error. Overcurrent of the Cassette 3 Lifter Motor was detected.
Remedy:	1. Check for error around the Lifter of the Cassette 3. 2. Check for hindrance to smooth movement of the Cassette Base Plate of the Cassette 3.

Error code:	E041-0004
Description:	Cassette 4 Lifter Motor error. Overcurrent of the Cassette 4 Lifter Motor was detected.
Remedy:	1. Check for error around the Lifter of the Cassette 4. 2. Check for hindrance to smooth movement of the Cassette Base Plate of the Cassette 4.

Error code:	E053-0001
Description:	Error in Reverse Upper Flapper Solenoid connection detection. Connection of the Reverse Upper Flapper Solenoid (SL5) cannot be detected 5 times with 20 msec time interval.
Remedy:	1. Check the connection of the Reverse Upper Flapper Solenoid (SL5). Solenoid side: J2115, Duplex Driver PCB side: J340 2. Replace the Reverse Upper Flapper Solenoid (SL5). 3. Replace the Duplex Driver PCB (PCB4). 4. Replace the DC Controller PCB (PCB1).

Error code:	E060-0001
Description:	Primary Charging Wire Shutter HP open error. The Primary Charging Wire Shutter HP Sensor (PS92) detected that the shutter was open although it was moved to the close position.
Remedy:	1. Check connection of the Primary Charging Wire Cleaning Motor (M1). 2. Replace the Primary Charging Wire Cleaning Motor (M1). 3. Check connection of the Primary Charging Wire Shutter HP Sensor (PS92). 4. Replace the Primary Charging Wire Shutter HP Sensor (PS92). 5. Check shutter mechanism of the Primary Charging Assembly. 6. Replace the Primary Charging Assembly. 7. Replace the DC Controller PCB.

Error code:	E060-0002
Description:	Primary Charging Wire Shutter HP close error. The Primary Charging Wire Shutter HP Sensor (PS92) detected that the shutter was closed although it was moved to the open position.
Remedy:	1. Check connection of the Primary Charging Wire Cleaning Motor (M1). 2. Replace the Primary Charging Wire Cleaning Motor (M1). 3. Check connection of the Primary Charging Wire Shutter HP Sensor (PS92). 4. Replace the Primary Charging Wire Shutter HP Sensor (PS92). 5. Check shutter mechanism of the Primary Charging Assembly. 6. Replace the Primary Charging Assembly. 7. Replace the DC Controller PCB

Error code:	E061-0001
Description:	At time of potential control, a specific level of potential is absent. Or, the limiter goes on. When forming an image, the potential is 10 V or less during initial rotation.
Remedy:	Turn off and then on the main power.

Error code:	E061-0101
Description:	Abnormal current run to the M Drum Abnormal current run to the M Drum (small current level or no drum is found)
Remedy:	1. Check installation of the Drum Unit. 2. Check if there is failure in grounding contact at the Drum Unit side (such as loosened screw which secures the plate at the contact point). 3. Check if there is failure in grounding contact with the Drum at Process Unit side. 4. Replace the Drum Unit. 5. Replace the Pre-exposure LED PCB (UN25,UN26).

Error code:	E064-00FF
Description:	High voltage setting error. With the state in which the developing AC is output, 600V or higher developing DC output was detected. (Basically, this error is not detected. However, to detect that the image formation-related backup data is corrupted or to protect the hardware in case of 600V or higher developing DC output, this is to be an error.)
Remedy:	1. Turn OFF and then ON the main power. 2. Replace the DCON PCB.

Error code:	E065-0001
Description:	Error in detection of abnormal M charging AC current value During the paper interval simple discharge current control, a current value that is higher than the target of 500[uA] is detected
Remedy:	Error in output of charging high voltage, Drum Unit error or environment control error 1. COPIER > DISPLAY > ANALOG; check if the TEMP value and the HUM value are matched with the environment temperature. When the values are dramatically mismatched (Lager than 15degrees Celsius) 2-1. Check the harness and connector between the DC Controller (UN09/ J206) and the Environment Sensor (UN45) 3-1. Replace the Environment Sensor (UN45) 4-1. Replace the DC Controller (UN9) When the values are matched 2-2. Check the state of the charging high voltage contact point 3-2. Replace the Drum Unit (M) 4-2. Check the harness and connector between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) 5-2. Replace the Primary Charging High Voltage PCB (UN06) 6-2. Replace the DC Controller PCB (UN09)

Error code:	E066-0001
Description:	Pre-transfer Charging Wire Shutter HP open error. The Pre-transfer Charging Wire Shutter HP Sensor (PS93) detected that the shutter was open although it was moved to the close position.
Remedy:	1. Check connection of the Pre-transfer Charging Wire Cleaning Motor (M2). 2. Replace the Pre-transfer Charging Wire Cleaning Motor (M2). 3. Check connection of the Pre-transfer Charging Wire Shutter HP Sensor (PS93). 4. Replace the Pre-transfer Charging Wire Shutter HP Sensor (PS93). 5. Check shutter mechanism of the Pre-transfer Charging Assembly. 6. Replace the Pre-transfer Charging Assembly. 7. Replace the DC Controller PCB.

Error code:	E066-0002
Description:	Pre-transfer Charging Wire Shutter HP close error. The Pre-transfer Charging Wire Shutter HP Sensor (PS93) detected that the shutter was closed although it was moved to the open position
Remedy:	1. Check connection of the Pre-transfer Charging Wire Cleaning Motor (M2). 2. Replace the Pre-transfer Charging Wire Cleaning Motor (M2). 3. Check connection of the Pre-transfer Charging Wire Shutter HP Sensor (PS93). 4. Replace the Pre-transfer Charging Wire Shutter HP Sensor (PS93). 5. Check shutter mechanism of the Pre-transfer Charging Assembly. 6. Replace the Pre-transfer Charging Assembly. 7. Replace the DC Controller PCB.

Error code:	E067-0001
Description:	Error in M primary transfer abnormal detection When trying to apply the specified voltage of 1500 [V] or higher
Remedy:	Error in the Primary Transfer High Voltage PCB, Error in the Primary Transfer Roller (ITB Unit) 1. Check failure of the harness between the Primary Transfer High Voltage PCB (UN04/J1001) and the DC Controller PCB (UN09/J205) (open circuit, trapped cable, connector disconnection). -> Replace the harness if it is faulty 2. Check connection failure between the Primary Transfer High Voltage PCB (UN04/J31) and the Primary Transfer Roller (Check that the connection is free from open circuit or GND contact) 3. Replace the Primary Transfer High Voltage PCB (UN04) 4. Replace the ITB Unit 5. Replace the DC Controller PCB (UN09). 6. Replace the Primary Transfer Power Supply Unit

Error code:	E068-0001
Description:	Pre-transfer charging high voltage output leak error. The leak detection signal was detected 5 times in a row for every 20 msec.
Remedy:	1. Check the connection between the Main Driver PCB (PCB2) and the High Voltage Unit. Main Driver side: J112, High Voltage Unit side: J3098 2. Check the connection between the Relay PCB (PCB5) and the High Voltage Unit. Relay side: J519, High Voltage Unit side: J3099 3. Replace the Pre-transfer Charging Assembly. 4. Check the connection inside of the High Voltage Unit. Check the connection of the High Voltage Unit Relay (J3098) and the Transfer High Voltage PCB (J3544). Check the connection of the High Voltage Unit Relay (J3099) and the Pre-transfer Charging PCB (J3545, J3500) 5. Replace the Main Driver PCB (PCB2). 6. Replace the Pre-transfer High Voltage Connector (FM4-1007). 7. Replace the Pre-transfer Transformer (Post Charging Trance) of the High Voltage Unit.

Error code:	E069-0001
Description:	Abnormal current is detected at the secondary transfer When 5 [uA] or smaller is detected at the secondary transfer
Remedy:	Error in the Secondary Transfer High Voltage PCB, Error in the Secondary Transfer Roller 1. Check failure of the harness between the Secondary Transfer High Voltage PCB (UN05/J201) and the DC Controller PCB (UN09/J10) (open circuit, trapped cable, connector disconnection). -> Replace the harness if it is faulty 2.Check connection failure between the Secondary Transfer High Voltage PCB (UN05/T1201) and the Secondary Transfer Outer Roller (Check that the connection is free from open circuit or GND contact) 3. Replace the Secondary Transfer High Voltage PCB (UN05) 4. Replace the Secondary Transfer Outer Roller 5. Replace the ITB Unit 6. Replace the DC Controller PCB (UN09) 7. Replace the Secondary Transfer Power Supply Unit

Error code:	E100-11xx
Description:	BD unlock error. Locked state was not detected within the specified period of time at start-up.
Remedy:	1. Check if the door is opened. Close the door. 2. Check the connection between the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35). DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor and BD PCB: J3011 3. Replace the Laser Scanner Unit. 4. Replace the Laser Driver PCB (PCB35). 5. Replace the DC Controller PCB (PCB1). MEMO: When condensation occurs inside of the machine or the Laser Scanner Unit, this error also occurs. When condensation occurs, leave the machine or the unit as it is until condensation disappears. (Use the machine or the unit in an environment where condensation does not occur.)

Error code:	E100-12xx
Description:	BD unlock error. After the BD range was specified, lock was unlocked for 1 second or longer.
Remedy:	1. Check if the door is opened. Close the door. 2. Check the connection between the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35). DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor and BD PCB: J3011 3. Replace the Laser Scanner Unit. 4. Replace the Laser Driver PCB (PCB35). 5. Replace the DC Controller PCB (PCB1). MEMO: When condensation occurs inside of the machine or the Laser Scanner Unit, this error also occurs. When condensation occurs, leave the machine or the unit as it is until condensation disappears. (Use the machine or the unit in an environment where condensation does not occur.)

Error code:	E100-13xx
Description:	Polygon Motor BD unlock error (Laser diode is not lit up/ failure of the BD PCB/power supply error, or condensation). During the Polygon speed change, lock was unlocked for 1 second or longer. (Laser diode is not lit up/failure of the BD PCB/power supply error, or condensation)
Remedy:	1. Check if the door is opened. Close the door. 2. Check the connection between the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35). DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor and BD PCB: J3011 3. Replace the Laser Scanner Unit. 4. Replace the Laser Driver PCB (PCB35). 5. Replace the DC Controller PCB (PCB1). MEMO: When condensation occurs inside of the machine or the Laser Scanner Unit, this error also occurs. When condensation occurs, leave the machine or the unit as it is until condensation disappears. (Use the machine or the unit in an environment where condensation does not occur.)

Error code:	E100-FFFF
Description:	Polygon Motor BD unlock error. Failed to get the Detailed Code (communication error, power supply error, PCB failure, etc.).
Remedy:	1. Check if the door is opened. Close the door. 2. Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35). DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3. Replace the Laser Scanner Unit. 4. Replace the Laser Driver PCB (PCB35). 5. Replace the DC Controller PCB (PCB1).

Error code:	E102-0001
Description:	EEPROM error An error has occurred in EEPROM of the Laser Scanner.
Remedy:	[Related parts] - Laser Scanner Unit (Unit of replacement: LASER SCANNER ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER SCANNER) - Interlock Switch 1 and 2 (SW02 and SW03/J24/pin 1 and 2) (Unit of replacement: COVER, INNER, FRONT, RIGHT) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. [Caution] After replacing the related parts, execute “Settings/ Registration> Adjustment/Maintenance> Adjust Image Quality> Auto Correct Color Mismatch”.

Error code:	E103-0001
Description:	With the Laser Scanners at YM side and CK side, the laser driver IDs were different The model IDs were different between the YM side and CK side when reading the model ID from EEPROM. (Detection is performed only with iR-ADVC5255, and C5250.)
Remedy:	Check the parts number of the Laser Scanner Unit. Replace the Laser Scanner Unit to make the following combinations. YM side: For iR-ADVC5255 and C5250, CK side: For iRADVC5255 and C5250 (recommended) YM side: For iR-ADVC5051 and C5045, CK side: For iR-ADVC5051 and C5045 (operates normally but not recommended)

Error code:	E110-11xx
Description:	Polygon Motor FG unlock error. Locked state was not detected within the specified period of time at start-up. (Power is not supplied/Polygon Motor signal error)
Remedy:	1. Check if the door is opened. Close the door. 2. Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35). DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3. Replace the Laser Scanner Unit. 4. Replace the Laser Driver PCB (PCB35). 5. Replace the DC Controller PCB (PCB1).

Error code:	E110-12xx
Description:	Polygon Motor FG unlock error. After the BD range was specified, lock was unlocked for 1 second or longer. (Power is not supplied/Polygon Motor signal error)
Remedy:	1. Check if the door is opened. Close the door. 2. Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35). DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3. Replace the Laser Scanner Unit. 4. Replace the Laser Driver PCB (PCB35). 5. Replace the DC Controller PCB (PCB1).

Error code:	E110-13xx
Description:	Polygon Motor FG unlock error. During the Polygon speed change, lock was unlocked for 1 second or longer. (Power is not supplied/Polygon Motor signal error)
Remedy:	1. Check if the door is opened. Close the door. 2. Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35). DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3. Replace the Laser Scanner Unit. 4. Replace the Laser Driver PCB (PCB35). 5. Replace the DC Controller PCB (PCB1).

Error code:	E110-FFFF
Description:	Polygon Motor FG unlock error. Failed to get the Detailed Code (communication error, power supply error, PCB failure).
Remedy:	1. Check if the door is opened. Close the door. 2. Check the connector connection, open circuit, and the caught cable of the DC Controller PCB (PCB1) and the Laser Driver PCB (PCB35). DC Controller side: J471, J472, Laser Driver side: J5100, J5101, Relay Harness connection to Polygon Motor (M44) and BD Sensor: J3011 3. Replace the Laser Scanner Unit. 4. Replace the Laser Driver PCB (PCB35). 5. Replace the DC Controller PCB (PCB1).

Error code:	E121-0001
Description:	The rotation of the laser cooling fan (1/2) is faulty. The lock signal arrives for 5 sec or more although the laser cooling fan 1 (FM3) is being driven.
Remedy:	- Check if there is no foreign material in the rotation assembly of the laser cooling fan 1. - Check if the connector (J503) of the relay PCB is mounted properly. - Replace the laser cooling fan 1. - Replace the DC controller PCB.

Error code:	E197-0001
Description:	Engine communication error
Causes:	Error between DC controller PCB and main controller PCB. Cause Failure in connection between PCB, failure in DC controller PCB, failure in controller PCB.
Remedy:	- Check the connection of the connector of the DC controller PCB and controller PCB - Replace the DC controller PCB - Replace the controller PCB

Error code:	E197-0002
Description:	Firmware error
Causes:	Unknown engine firmware error
Remedy:	1. Turn OFF and then ON the power. 2. Update firmware. 3. Replace the DC Controller PCB.

Error code:	E197-0003
Description:	There is an error in the communication with the fixing feed PCB. Following the end of initialization of the communication between the DC controller and the fixing/feeding unit, as many as 10 communication errors occur continuously.
Remedy:	Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power.

Error code:	E197-0004
Description:	There is an error in the communication with the fixing feed PCB. At the start of drum initial multiple rotation, there is no signal indicating the start of 24V in the fixing assembly in the communication between the DC controller and the fixing/feeding unit.
Remedy:	Turn off the main power, and check the DC controller PCB wiring and the 24V system fuse; then, turn on the main power.

Error code:	E197-0005
Description:	Error in Main Driver PCB Analog Connector connection detection. Connection between the DC Controller PCB (PCB1) and the Main Driver PCB (PCB2) is disconnected.
Remedy:	1. Check the connection of the DC Controller PCB (PCB1) and the Main Driver PCB (PCB2). DC Controller side: J413, Main Driver side: J124 2. Replace the Main Driver PCB (PCB2). 3. Replace the DC Controller PCB (PCB1).

Error code:	E197-0006
Description:	Serial communication error. Ex serial communication error with the DC Controller PCB.
Remedy:	1. Check connection of the DC Controller PCB (J1210). 2. Replace the DC Controller PCB.

Error code:	E197-0008
Description:	Serial communication error. Ex serial communication error with the Multi Deck.
Remedy:	1. Check the connection between the Buffer Driver PCB and the DC Controller PCB (J1226). 2. Replace the DC Controller PCB. 3. Replace the Buffer Driver PCB.

Error code:	E197-0009
Description:	Serial communication error. Ex serial communication error with the Multi Deck.
Remedy:	1. Check the connection between the Buffer Driver PCB and the DC Controller PCB (J1226). 2. Replace the DC Controller PCB. 3. Replace the Buffer Driver PCB.

Error code:	E197-0010
Description:	Error in Primary Charging High Voltage PCB connection detection. Connection between the Main Driver PCB (PCB2) and the Primary Charging High Voltage PCB (PCB11) is disconnected.
Remedy:	1. Check the connection between the Main Driver PCB (PCB2) and the Primary Charging High Voltage PCB (PCB11). Main Driver side: J111, Primary Charging High Voltage side: J3501 2. Replace the Primary Charging High Voltage PCB (PCB11).

Error code:	E197-0011
Description:	Error in Developing High Voltage PCB connection detection. Connection between the Main Driver PCB (PCB2) and the Developing High Voltage PCB (PCB12) is disconnected.
Remedy:	1. Check the connection between the Main Driver PCB (PCB2) and the Developing High Voltage PCB (PCB12). Main Driver side: J112, Developing High Voltage side: J3511 2. Replace the Developing High Voltage PCB (PCB12).

Error code:	E197-0012
Description:	Error in Transfer High Voltage PCB connection detection. Connection between the Duplex Driver PCB (PCB4) and the Transfer High Voltage PCB (PCB13) is disconnected.
Remedy:	1. Check the connection between the Duplex Driver PCB (PCB4) and the Transfer High Voltage PCB (PCB13). Duplex Driver side: J343, Transfer High Voltage side: J3062 2. Replace the Transfer High Voltage PCB (PCB13).

Error code:	E197-0181
Description:	Timeout error in EHOB reception-waiting Communication failure between the DC Controller PCB (UN1) and Laser Scanner Unit.
Remedy:	1. Turn OFF and then ON the power. 2. Check connection of harness on the target color side (YM/CK). 3. Replace the DC Controller PCB (UN1). 4. Replace the Laser Scanner Unit. 5. Replace the harness on the target color side (YM/CK).

Error code:	E202-0001
Description:	Reader HP sensor fault
Causes:	Reader HP outward fault The CCD unit moves backward, but does not move to the home position.
Remedy:	- Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit.

Error code:	E202-0002
Description:	Contact Sensor HP error, Failure in return
Causes:	Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position.
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board.

Error code:	E202-0101
Description:	Glass home position error. Failure of detection of the glass home position (outward)
Remedy:	1. Displacement/disconnection of the connector of the glass movement home position sensor (SR11) 2. Damage to the glass movement home position sensor 3. Damage to the glass movement motor (M9) 4. Damage to the DADF driver PCB (PCB1)

Error code:	E202-0102
Description:	Glass home position error. Failure of detection of the glass home position (homeward)
Remedy:	1. Displacement/disconnection of the connector of the glass movement home position sensor (SR11) 2. Damage to the glass movement home position sensor 3. Damage to the glass movement motor (M9) 4. Damage to the DADF driver PCB (PCB1)

Error code:	E227-0001
Description:	Reader unit power supply error When the 24 V port is OFF when the power is turned ON.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0002
Description:	Reader unit power supply error When the 24 V port is OFF when a job is started.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0003
Description:	Reader unit power supply error When the 24 V port is OFF when a job is finished.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0004
Description:	Reader unit power supply error When the 24 V port is OFF during load drive.
Remedy:	Disconnect and re-connect the power connector. Replace the power supply

Error code:	E227-0101
Description:	Power supply (24 V) error. The 24 V port is turned off at the time of power-on at DADF
Remedy:	Because the DC Controller turns OFF the 24 V Power Supply when an error is detected, it is needed to restart and check the power output before the machine detects the error to determine whether the cause of the error is power supply. If there is no power output, power supply is the cause. If there is power output, factor other than power supply can be the cause of the error. 1. Turn OFF and then ON the power. 2. Check the connection between Reader and Printer, and check that the Cable is not open-circuit. 3. Check the 24 V port of the Reader Controller PCB and DADF Driver PCB. 4. Check the power supply and Relay PCB on the Printer side. 5. Replace the Reader Controller PCB and DADF Driver PCB.

Error code:	E227-0102
Description:	Power supply (24 V) error. The 24 V port is turned off at the time of job start at DADF.
Remedy:	Because the DC Controller turns OFF the 24 V Power Supply when an error is detected, it is needed to restart and check the power output before the machine detects the error to determine whether the cause of the error is power supply. If there is no power output, power supply is the cause. If there is power output, factor other than power supply can be the cause of the error. 1. Turn OFF and then ON the power. 2. Check the connection between Reader and Printer, and check that the Cable is not open-circuit. 3. Check the 24 V port of the Reader Controller PCB and DADF Driver PCB. 4. Check the power supply and Relay PCB on the Printer side. 5. Replace the Reader Controller PCB and DADF Driver PCB.

Error code:	E227-0103
Description:	Power supply (24 V) error. The 24 V port is turned off at the time of job completion at DADF.
Remedy:	Because the DC Controller turns OFF the 24 V Power Supply when an error is detected, it is needed to restart and check the power output before the machine detects the error to determine whether the cause of the error is power supply. If there is no power output, power supply is the cause. If there is power output, factor other than power supply can be the cause of the error. 1. Turn OFF and then ON the power. 2. Check the connection between Reader and Printer, and check that the Cable is not open-circuit. 3. Check the 24 V port of the Reader Controller PCB and DADF Driver PCB. 4. Check the power supply and Relay PCB on the Printer side. 5. Replace the Reader Controller PCB and DADF Driver PCB.

Error code:	E240-0000
Description:	Error in communication between main controller and DC controller Serial communication error
Causes:	The main controller PCB is faulty. The DC controller PCB is faulty.
Remedy:	Check the connector connections. Check the DC controller PCB (MAISY). Replace the No.1 main controller circuit.

Error code:	E240-0001
Description:	Error in communication of controller There is no response when 3 sec passed since the main controller had sent the pickup request to DC controller during printing.
Remedy:	Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB

Error code:	E240-0002
Description:	Error in communication between main controller and DC controllerWhen the response from the DC controller does not arrive within the prescribed period of time during printing
Remedy:	Check the connector connections. Check the DC controller PCB (MAISY). Replace the No.1 main controller circuit.

Error code:	E240-0003
Description:	Error in communication of controller The engine is activated when jam occurs.
Remedy:	Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB

Error code:	E246-0001
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E246-0002
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E246-0003
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E246-0005
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E247-0001
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E247-0002
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E247-0003
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E247-0004
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E248-0000
Description:	There is an error in the EEPROM. At time of start-up, a check error has occurred on the SRAM board
Remedy:	Turn off the main power, and check the SRAM board; then, as necessary, replace the SRAM board, and turn on the main power.

Error code:	E248-0001
Description:	EEPROM access error
Causes:	Error at EEPROM power-on EEPROM data cannot be read at power-on.
Remedy:	Replace reader unit.

Error code:	E248-0002
Description:	EEPROM access error
Causes:	Error in EEPROM writing EEPROM writing cannot be performed.
Remedy:	Replace reader unit.

Error code:	E248-0003
Description:	EEPROM access error
Causes:	Error in EEPROM reading after writing EEPROM reading cannot be performed after writing is performed.
Remedy:	Replace reader unit.

Error code:	E263-0000
Description:	Error in Current Sensor reference voltage generation. The reference voltage is not within the range of reference value.
Remedy:	1. Check the connection between the AC Driver PCB and the Main Driver PCB (connector disconnection, open circuit, short circuit of harness). AC Driver side: J615, Main Driver side: J103 2. Replace the AC Driver PCB. 3. Replace the Main Driver PCB (PCB2).

Error code:	E263-0001
Description:	Current Sensor error. An error is detected in the value of the Current Sensor (SE601) (the value remains at the upper limit).
Remedy:	1. Check the connection between the AC Driver PCB and the Main Driver PCB (connector disconnection, open circuit, short circuit of harness). AC Driver side: J615, Main Driver side: J103 2. Replace the AC Driver PCB. 3. Replace the Main Driver PCB (PCB2).

Error code:	E263-0002
Description:	Current Sensor error. An error is detected in the value of the Current Sensor (SE601) (the value remains at the lower limit).
Remedy:	1. Check the connection between the AC Driver PCB and the Main Driver PCB (connector disconnection, open circuit, short circuit of harness). AC Driver side: J615, Main Driver side: J103 2. Replace the AC Driver PCB. 3. Replace the Main Driver PCB (PCB2).

Error code:	E263-0003
Description:	Error in Current Sensor accuracy. The value of the Current Sensor (SE601) is not within the range of reference value.
Remedy:	1. Check the connection between the AC Driver PCB and the Main Driver PCB (connector disconnection, open circuit, short circuit of harness). AC Driver side: J615, Main Driver side: J103 2. Replace the AC Driver PCB. 3. Replace the Main Driver PCB (PCB2).

Error code:	E270-0001
Description:	Failure of the front side vertical direction synchronization signal. The vertical direction synchronization signal (VSYNC) was not sent from the CMOS PCB (front side optical unit) correctly, and an image failure occurred or the operation stopped in failure.
Remedy:	1. Displacement/disconnection of the connector of the optical unit (reader) 2. Displacement/disconnection of the connector of the reader controller PCB (PCB1) 3. Failure of the optical unit (reader) 4. Failure of the reader controller PCB

Error code:	E270-0002
Description:	Failure of the horizontal/vertical direction synchronization signal. The vertical direction synchronization signal (VSYNC) was not sent due to a failure of the horizontal direction synchronization signal (HSYNC), and an image failure occurred or the operation stopped in failure.
Remedy:	1. Displacement/disconnection of the connector of the optical unit (reader/DADF) 2. Displacement/disconnection of the connector of the reader controller PCB (PCB1) 3. Failure of the optical unit (reader/DADF) 4. Failure of the reader controller PCB

Error code:	E270-0101
Description:	Failure of the backside vertical scanning direction synchronization signal. The vertical direction synchronization signal (VSYNC) was not sent from the CMOS PCB (backside optical unit) correctly, and an image failure occurred or the operation stopped in failure.
Remedy:	1. Displacement/disconnection of the connector of the optical unit (DADF) 2. Displacement/disconnection of the connector of the reader controller PCB (PCB1) 3. Failure of the optical unit (DADF) 4. Failure of the reader controller PCB

Error code:	E280-0001
Description:	Reading unit communication error Reception status error
Remedy:	Disconnect and then connect the flexible cable. Replace the flexible cable

Error code:	E280-0101
Description:	Communication error between Reader Controller PCB (PCB1) and Scanner Unit (Paper Back) (Reader). Within the specified period of time, communication between the Reader Controller PCB and Scanner Unit (Paper Back) was not started.
Remedy:	1. Connector disconnection/open circuit of the Scanner Unit (Paper Back) (Reader) ?¨ Connect the connector/ Replace the harness. 2. Connector disconnection/open circuit of the Reader Controller PCB (PCB1). ?¨ Connect the connector/ Replace the harness. 3. Replace the Scanner Unit (Reader). 4. Replace the Reader Controller PCB.

Error code:	E301-0001
Description:	Insufficient light intensity in shading
Causes:	Insufficient light intensity at shading.
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board

Error code:	E301-0101
Description:	Backside light intensity failure. The light intensity amount at backside shading is less than the standard level.
Remedy:	Replace the optical unit (DADF)

Error code:	E302-0001
Description:	Shading error
Causes:	When the light intensity is below the reference level at shading
Remedy:	1. Disconnect and then connect the Flexible Cable. 2. Replace the Flexible Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB (PCB2).

Error code:	E302-0101
Description:	Backside white shading failure. Shading RAM access failure occurred, or the shading value is less than or more than the specified level.
Remedy:	1. Connector disconnection/open circuit of the Scanner Unit (Paper Back) (Reader) ?¨ Connect the connector/ Replace the harness. 2. Connector disconnection/open circuit of the Reader Controller PCB (PCB1). ?¨ Connect the connector/ Replace the harness. 3. Replace the Scanner Unit (Paper Back) (Reader). 4. Replace the Reader Controller PCB.

Error code:	E315-0007
Description:	There is an error in image data. There is an error in JBIG encoding.
Remedy:	Turn off and then back on the power.

Error code:	E315-000d
Description:	There is an error in image data. There is an error in JBIG decoding.
Remedy:	Turn off and then back on the power.

Error code:	E315-000e
Description:	Image data trouble Damaged data (trouble in memory or HDD) Software decoding error
Remedy:	Replace the image memory (SDRAM) or HDD.

Error code:	E315-0025
Description:	Abnormality of image data ASIC (for compression/decompression) on the image conversion PCB is faulty. Image data transfer error during rotation processing.
Remedy:	Check on connection of the image conversion board, Replace the image conversion board

Error code:	E315-0027
Description:	There is an error in image data. Error in ROTU timeout
Remedy:	Replace SDRAM. Replace HDD. Replace the main controller PCB.

Error code:	E315-0033
Description:	There is an error in image data. Error in MemFill hardware
Remedy:	Replace the main controller PCB.

Error code:	E315-0035
Description:	There is an error in image data. Error in MemFill timeout
Remedy:	Replace the main controller PCB.

Error code:	E315-0100
Description:	There is an error in image data. Error in PrcOverRun
Remedy:	Replace the main controller PCB.

Error code:	E315-0500
Description:	There is an error in image data. Error in device timeout [location to be detected] image process module (SCIO) [Detection timing] when there is no interruption 2 min after the operation has been started
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0501
Description:	There is an error in image data. Device: abnormal termination error [location to be detected] image process module (SCIO) [Detection timing] When abnormal interruption is detected after the operation has been started.
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0510
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (SCIP) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0511
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (SCIP) [Detection timing] when abnormal interruption is detected after the operation has been detected
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0520
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (CMIP) [Detection timing] When there is no interruption 2 min after the operation has been started
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB.

Error code:	E315-0521
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (CMIP) [Detection timing] when abnormal interruption is detected after the operation has been detected
Remedy:	Check connection with DDI-S cable(RCON). Replace the main controller PCB

Error code:	E315-0530
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (JPEN) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently.

Error code:	E315-0531
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (JPEN) [Detection timing] when abnormal interruption is detected after the operation has been started.
Remedy:	Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently.

Error code:	E315-0540
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (JPDE) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently.

Error code:	E315-0541
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (JPDE) [Detection timing] when abnormal interruption is detected after the operation has been started
Remedy:	Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently.

Error code:	E315-0550
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (PRIP) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Error code:	E315-0551
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (PRIP) [Detection timing] when abnormal interruption is detected after the operation has been started.
Remedy:	Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Error code:	E315-0560
Description:	There is an error in image data. Device: timeout error [Location to be detected] image process module (PRIO) [Detection timing] when there is no interruption 2 min after the operation has been started.
Remedy:	Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Error code:	E315-0561
Description:	There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (PRIO) [Detection timing] when abnormal interruption is detected after the operation has been started.
Remedy:	Check connection with DDI-P cable(DCON). Replace the main controller PCB.

Error code:	E350-0000
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E350-0001
Description:	Fault in the soft ID PCB/function An error has occurred in the course of full data read operation on the soft ID PCB.
Remedy:	Turn off the main power, and check the connection of the soft ID PCB. If the remedy fails, replace the soft ID PCB.

Error code:	E350-0002
Description:	Fault in the soft ID PCB/function The value of the check sum area of all data read from the soft ID PCB and the result of checksum computation do not match.
Remedy:	Turn off the main power, and replace the soft ID PCB. If the remedy fails, replace the soft ID PCB.

Error code:	E350-0003
Description:	Fault in the soft ID PCB/function The values in the soft ID check sum area of FRAM, SRAM1, and SRAM2 and the result of a check sum computation differ.
Remedy:	Turn off the main power, and check the connection of the soft ID PCB. If the remedy fails, replace the soft ID PCB.

Error code:	E350-3000
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E351-0000
Description:	Main controller PCB fault
Causes:	Internal error of the main controller PCB Cause Main controller PCB fault.
Remedy:	- Check the connection of main controller PCB. - Replace main controller PCB.

Error code:	E354-0001
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E354-0002
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E355-0001
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E355-0003
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E355-0004
Description:	System error
Causes:	System error
Remedy:	Contact the sales company.

Error code:	E400-0001
Description:	Feeder communication error Checksum error
Remedy:	Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub).

Error code:	E400-0002
Description:	Feeder communication error Reception status error
Remedy:	Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub).

Error code:	E401-0001
Description:	Pickup roller unit up/down failure. Even when the pickup roller unit up/down motor (M10) is driven, the level of the pickup roller unit up/down home position sensor (SR12) does not change within a specified period.
Remedy:	1. Displacement/disconnection of the connector of the pickup roller unit up/down home position sensor (SR12) 2. Displacement/disconnection of the connector of the pickup roller unit up/down motor (M10) 3. Failure of the pickup roller unit up/down home position sensor 4. Failure of the pickup roller unit up/down motor

Error code:	E401-0002
Description:	Pickup roller unit up/down failure. Even when the pickup roller unit up/down motor (M10) is driven, the level of the pickup roller unit up/down home position sensor (SR12) does not change within a specified period.
Remedy:	1. Displacement/disconnection of the connector of the pickup roller unit up/down home position sensor (SR12) 2. Displacement/disconnection of the connector of the pickup roller unit up/down motor (M10) 3. Failure of the pickup roller unit up/down home position sensor 4. Failure of the pickup roller unit up/down motor

Error code:	E407-0001
Description:	Failure of the tray up/down motor (M8). Even when the tray up/down motor (M8) is driven, the tray home position sensor (SR13) is not turned ON or OFF within a specified period.
Remedy:	1. Displacement/disconnection of the connector of the tray home position sensor (SR13) 2. Displacement/disconnection of the connector of the tray up/down motor (M8) 3. Failure of the tray home position sensor 4. Failure of the tray up/down motor

Error code:	E407-0002
Description:	Failure of the tray up/down motor (M8). Even when the tray up/down motor (M8) is driven, the paper surface sensor (SR6) is not turned ON within a specified period.
Remedy:	1. Displacement/disconnection of the connector of the paper surface sensor (SR6) 2. Displacement/disconnection of the connector of the tray up/down motor (M8) 3. Failure of the paper surface sensor 4. Failure of the tray up/down motor

Error code:	E413-0001
Description:	Pressure motor trouble Pressure HP sensor OPEN
Remedy:	Replace the pressure motor.

Error code:	E413-0002
Description:	Pressure motor trouble Pressure HP sensor CLOSE
Remedy:	Replace the pressure motor.

Error code:	E413-0011
Description:	Failure of the DADF detachment motor 2 (M7). Even when the DADF detachment motor 2 (M7) is driven, the DADF detachment home position sensor 2 (SR16) is not turned ON within a specified period.
Remedy:	1. Displacement/disconnection of the connector of the detachment home position sensor 2 (SR16) 2. Displacement/disconnection of the connector of the detachment motor 2 (M7) 3. Failure of the detachment home position sensor 2 4. Failure of the detachment motor 2 5. Failure of the DADF driver PCB (PCB1)

Error code:	E413-0012
Description:	Failure of the DADF detachment motor 2 (M7). Even when the DADF detachment motor 2 (M7) is driven, the DADF detachment home position sensor 2 (SR16) is not turned OFF within a specified period.
Remedy:	1. Displacement/disconnection of the connector of the detachment home position sensor 2 (SR16) 2. Displacement/disconnection of the connector of the detachment motor 2 (M7) 3. Failure of the detachment home position sensor 2 4. Failure of the detachment motor 2 5. Failure of the DADF driver PCB (PCB1)

Error code:	E423-0001
Description:	DADF SDRAM error. SDRAM access error
Remedy:	Failure of the SDRAM (video image memory) located on the reader controller PCB (PCB1)

Error code:	E423-0002
Description:	DADF SDRAM error. SDRAM Verify error
Remedy:	Failure of the SDRAM (video image memory) located on the reader controller PCB (PCB1)

Error code:	E490-0001
Description:	Wrong model error When the feeder of another model has been detected
Remedy:	Connect the feeder for this unit.

Error code:	E500-0000
Description:	The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less
Causes:	The copier harness is faulty. (disconnected connector, open circuit) The finisher controller PCB or the copier’s DC controller PCB is faulty.

Error code:	E503-0001
Description:	fault in communicatio n with the finisher (Finisher-Q3/ Q4)

Error code:	E503-0002
Description:	Saddle communication error When communication with the saddle stitcher is interrupted
Remedy:	- Check the connections between the saddle stitcher controller PCB and finisher controller PCB. - Replace the saddle stitcher controller PCB and finisher controller PCB.

Error code:	E503-0021
Description:	Error in communication between the finisher - inserter (Finisher-K1). Communication failed between finisher - insertion unit
Remedy:	1. The connector on the cable between the finisher and the insertion unit is disconnected. 2. The cable between the finisher and the insertion unit is faulty. 3. The finisher controller PCB is faulty. 4. The insertion unit controller PCB is faulty.

Error code:	E503-0022
Description:	Error in communication between the finisher - inserter (Finisher-K1). Communication failed between finisher - insertion unit
Remedy:	1. The connector on the cable between the finisher and the insertion unit is disconnected. 2. The cable between the finisher and the insertion unit is faulty. 3. The finisher controller PCB is faulty. 4. The insertion unit controller PCB is faulty.

Error code:	E503-0041
Description:	Error in communication between the finisher - integration unit(Finisher-A1). Communication failed between finisher - integration unit
Remedy:	1. The connector on the cable between the finisher and the integration unit is disconnected. 2. The cable between the finisher and the integration unit is faulty. 3. The finisher controller PCB is faulty. 4. The integration controller PCB is faulty.

Error code:	E503-0042
Description:	Error in communication between the finisher - integration unit (Finisher-A1). Communication failed between finisher - integration unit
Remedy:	1. The connector on the cable between the finisher and the integration unit is disconnected. 2. The cable between the finisher and the integration unit is faulty. 3. The integration controller PCB is faulty. 4. The finisher controller PCB is faulty

Error code:	E503-0051
Description:	Error in communication between the integration unit - professional puncher(Finisher-A1). Communication failed between the integration unit - professional puncher
Remedy:	1. The connector on the cable between the integration unit and the professional puncher is disconnected. 2. The cable between the integration unit and the professional puncher is faulty. 3. The integration controller PCB is faulty. 4. The professional puncher controller PCB is faulty.

Error code:	E503-0053
Description:	Error in communication between the integration unit - professional puncher.
Remedy:	1. The connector on the cable between the integration unit and the professional puncher is disconnected. 2. The cable between the integration unit and the professional puncher is faulty. 3. The integration controller PCB is faulty. 4. The professional puncher controller PCB is faulty.

Error code:	E503-0061
Description:	Error in communication between the finisher - paper folding unit (Finisher-K1). Communication failed between the finisher - paper folding unit
Remedy:	1. The connector on the cable between the finisher and the paper folding unit is disconnected. 2. The cable between the finisher and the paper folding unit is faulty. 3. The finisher controller PCB is faulty. 4. The paper folding unit controller PCB is faulty.

Error code:	E503-0062
Description:	Error in communication between the finisher - paper folding unit (Finisher-K1). Communication failed between the finisher - paper folding unit
Remedy:	1. The connector on the cable between the finisher and the paper folding unit is disconnected. 2. The cable between the finisher and the paper folding unit is faulty. 3. The finisher controller PCB is faulty. 4. The paper folding unit controller PCB is faulty.

Error code:	E503-0081
Description:	Error in communication between the saddle stitcher - trimmer (Finisher-K1). Communication failed between the saddle stitcher - trimmer
Remedy:	1. The connector on the wiring between the saddle stitcher and the trimmer is disconnected. 2. The wiring between the saddle stitcher and the trimmer is faulty. 3. The trimmer controller PCB is faulty. 4. The saddle stitcher controller PCB is faulty. 5. The finisher controller PCB is faulty.

Error code:	E503-0082
Description:	Error in communication between the saddle stitcher - trimmer (Finisher-K1). Communication failed between the saddle stitcher - trimmer
Remedy:	1. The connector on the wiring between the saddle stitcher and the trimmer is disconnected. 2. The wiring between the saddle stitcher and the trimmer is faulty. 3. The trimmer controller PCB is faulty. 4. The saddle stitcher controller PCB is faulty. 5. The finisher controller PCB is faulty.

Error code:	E505-0001
Description:	Finisher backup memory error When the checksum value calculated by the CPU differs from the checksum values of the data held inside the RAM
Causes:	The backup RAM is faulty.
Remedy:	Replace the finisher controller PCB.

Error code:	E505-0003
Description:	Finisher backup memory error Finisher controller EEPROM writing error
Remedy:	Replace the finisher controller PCB

Error code:	E505-0005
Description:	Paper folding unit backup RAM error. Reading/writing error of EEPROM on the paper folding unit controller PCB
Remedy:	The paper folding unit controller PCB is faulty.

Error code:	E514-8001
Description:	Bundling (forward rotation direction) error When the trailing edge fails to leave the trailing edge assist home position even when the trailing edge assist motor has been driven for 3 sec.
Remedy:	Replace the trailing edge assist motor (M109) and trailing edge assist home position sensor (PI109).

Error code:	E514-8002
Description:	Bundling (forward rotation direction) error When the trailing edge fails to return to the trailing edge assist home position even when the trailing edge assist motor has been driven for 3 sec.
Remedy:	Replace the trailing edge assist motor (M109) and trailing edge assist home position sensor (PI109).

Error code:	E514-8003
Description:	Error in the gripper motor (Finisher-A1). The gripper does not come off the gripper HP sensor when the gripper motor has been driven for 3 seconds.
Remedy:	1. The connector of the gripper HP sensor (S140) or the gripper motor (M117) are disconnected. 2. The wiring of the gripper HP sensor) or the gripper motor are faulty. 3. The gripper HP sensor is faulty. 4. The gripper motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E514-8004
Description:	Error in the gripper motor (Finisher-K1). The gripper HP sensor does not detect the gripper when the gripper motor has been driven for 3 seconds.
Remedy:	1. The connector of the gripper HP sensor (S140) or the gripper motor (M117) are disconnected. 2. The wiring of the gripper HP sensor or the gripper motor are faulty. 3. The gripper HP sensor is faulty. 4. The gripper motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E514-8005
Description:	Error in the gripper motor (Finisher-K1). The gripper does not come off the position sensor when the gripper motor has been driven for 3 seconds.
Remedy:	1. The connector of the gripper position sensor (S115) or the gripper motor (M117) are disconnected. 2. The wiring of the gripper position sensor or the gripper motor are faulty. 3. The gripper position sensor is faulty. 4. The gripper motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E514-8006
Description:	Error in the gripper motor (Finisher-K1). The gripper position sensor does not detect the gripper when the gripper motor has been driven for 3 seconds.
Remedy:	1. The connector of the gripper position sensor (S115) or the gripper motor (M117) are disconnected. 2. The wiring of the gripper position sensor or the gripper motor are faulty. 3. The gripper position sensor is faulty. 4. The gripper motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E518-8001
Description:	Error in folding feed motor lock (Document Insertion Folding Unit/Paper Folding Unit). The fold transport motor (M5/M11) lock signal has been detected for more than the specified period of time.
Remedy:	1. Connector of Folding feed motor (M5/M11) is disconnected. 2. Folding feed motor is faulty.

Error code:	E530-8000
Description:	Error in the front or rear alignment motor. The front or rear alignment motor operate abnormally during initialization.
Remedy:	1. The connector of the front/rear alignment HP sensor (S108/S109) or the front/rear alignment motor (M108/ M109) are disconnected. 2. The wiring of the front/rear alignment HP sensor or the front/rear alignment motor are faulty. 3. The front/rear alignment HP sensor is faulty. 4. The front/rear alignment motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E530-8001
Description:	Alignment error When the alignment plate fails to leave the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec.
Remedy:	Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106).

Error code:	E530-8002
Description:	Alignment error When the alignment plate fails to return to the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec.
Remedy:	Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106).

Error code:	E531-8001
Description:	Stapler error When the stapler fails to leave the stapler home position even though the stapler motor was driven for 0.5 sec.
Remedy:	Replace the stapler motor (M111) and stapler home position detection sensor (PI50).

Error code:	E531-8002
Description:	Stapler error When the stapler fails to return to the stapler home position even though the stapler motor was driven for 0.5 sec.
Remedy:	Replace the stapler motor (M111) and stapler home position detection sensor (PI50).

Error code:	E532-8000
Description:	Error in the staple shift motor. The staple shift motor operate abnormally during initialization.
Remedy:	1. The connector of the stapler shift HP sensor (S107) or the staple shift motor (M107) are disconnected. 2. The wiring of the stapler shift HP sensor or the staple shift motor are faulty. 3. The stapler shift HP sensor is faulty. 4. The staple shift motor is faulty. 5. The finisher controller PCB is faulty

Error code:	E532-8001
Description:	There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go off within a specific period of time after the stapler shift motor has started to rotate.
Remedy:	1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected?

Error code:	E532-8002
Description:	There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go on within a specific period of time after the stapler shift motor has started to rotate.
Remedy:	1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected?

Error code:	E535-0001
Description:	There is a fault in the swing mechanism. Finisher-N1/Saddle Finisher-N2 The swing motor (M7) or the swing guide open sensor (PI18) is faulty. The swing guide closed switch does not go ON when the swing motor has been rotated in reverse for 1 sec.
Causes:	The delivery motor (M2) is faulty. The swing guide open sensor (PI18) is faulty.
Remedy:	Replace the swing HP sensor (PI35) , Replace the swing motor (M36)

Error code:	E535-0002
Description:	There is a fault in the swing mechanism. Finisher-N1/Saddle Finisher-N2 The swing motor (M7) or the swing guide closed switch (MS6) is faulty. The swing guide open switch does not go ON when the swing motor has been rotated in reverse for 1 sec.
Causes:	The safety area switch (MS3) is faulty. The swing guide open detecting switch (MS6) is faulty.
Remedy:	Replace the swing HP sensor (PI35) , Replace the swing motor (M36)

Error code:	E535-0003
Description:	There is an error in the staple swing mechanism. (finisher R1/R2) There is an error in relation to an hazardous area..
Causes:	The delivery motor (M2) is faulty. The swing guide closed detecting switch 2 (MS6) is faulty.
Remedy:	1) Check the swing home position sensor. Is the sensor normal? 2) Check the writing between the finisher controller PCB and the swing motor. Is the wiring normal? 3) Check the swing mechanism. Is there a fault? 4) Try replacing the swing motor. Is the problem corrected?

Error code:	E535-0004
Description:	There is a fault in the swing mechanism. Finisher-N1/Saddle Finisher-N2 The swing motor (M7) or the swing motor clock sensor (PI20) is faulty. There is no clock pulse for 0.2 sec while swinging operation is under way.
Remedy:	1. The connector of the swing guide height detection sensor (S118) or the swing guide motor (M110) are disconnected. 2. The wiring of the swing guide height detection sensor or the swing guide motor are faulty. 3. The swing guide height detection sensor is faulty. 4. The swing guide motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E537-8001
Description:	Front alignment error When the alignment plate fails to leave the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec.
Remedy:	Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107).

Error code:	E537-8002
Description:	Front alignment error When the alignment plate fails to return to the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec.
Remedy:	Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107).

Error code:	E540-8001
Description:	Tray up/down error - When the tray fails to return to the home position even when the 1st tray shift motor has been driven for 20 sec. - When the tray fails to move to another area even when the 1st tray shift motor has been driven for 4 sec.
Remedy:	- Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107)

Error code:	E540-8002
Description:	Tray up/down error When a danger area is reached before the sheet level is detected by the 1st tray sheet level detection sensor during the sheet level detection operation - When a discontinuous area was detected during the tray operation
Remedy:	- Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107)

Error code:	E540-8003
Description:	Tray up/down error When the input of the clock signal could not be detected within 0.2 sec. during the operation of the 1st tray shift motor
Remedy:	- Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107)

Error code:	E540-8013
Description:	Error in the swing guide safety switch. The swing guide safety switch is turned ON while the tray 1 operates.
Remedy:	1. The connector of the swing guide safety switch (front/ rear) (SW102/SW104) or the staple position switch (SW103) are disconnected. 2. The connector of the swing guide solenoid (SL101) or the tray 1 shift motor (M105) are disconnected. 3. The wiring of the swing guide safety switch (front/rear) or the staple position switch are faulty. 4. The wiring of the swing guide solenoid or the tray 1 shift motor are faulty. 5. The swing guide safety switch (front/rear) is faulty. 6. The staple position switch is faulty. 7. The swing guide solenoid is faulty. 8. The tray 1 shift motor is faulty. 9. The finisher controller PCB is faulty.

Error code:	E542-8001
Description:	Tray shift error When the tray fails to return to the home position even when the 2nd tray shift motor has been driven for 20 sec. - When the tray fails to move to another area even when the 2nd tray shift motor has been driven for 4 sec.
Remedy:	- Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108).

Error code:	E542-8002
Description:	Tray shift error - When the upper limit area is reached before the sheet level is detected by the 2nd tray sheet level detection sensor 1 during a sheet level detection operation - When a discontinuous area was detected during the tray operation - When the fact that the area ahead of the 2nd tray sheet level detection sensor 2 has been reached is detected before the sheet level is detected by the 2nd tray sheet level detection sensor 2 during an escape operation
Remedy:	- Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108).

Error code:	E542-8003
Description:	Lower tray up/down error Finisher-Z1 The safety switch is activated.
Remedy:	Replace the shift motor (M38) of the tray 2, Replace the shift area sensor PCB of the tray 2

Error code:	E542-8013
Description:	Error in the swing guide safety switch. The swing guide safety switch (front/rear) is turned ON while the tray 2 operates.
Remedy:	1. The connector of the swing guide safety switch (front/ rear) (SW102/SW104) or the staple position switch (SW103) are disconnected. 2. The connector of the swing guide solenoid (SL101) or the tray 2 shift motor (M217) are disconnected. 3. The wiring of the swing guide safety switch (front/rear) or the staple position switch are faulty. 4. The wiring of the swing guide solenoid or the tray 2 shift motor are faulty. 5. The swing guide safety switch (front/rear) is faulty. 6. The staple position switch is faulty. 7. The swing guide solenoid is faulty. 8. The tray 2 shift motor is faulty. 9. The finisher controller PCB is faulty.

Error code:	E551-0001
Description:	A. Error in power supply fan (Document Insertion Unit) B. Error in power supply fan (FAN101) (Finisher). A. The lock signal ON is detected while the fan operation. B. The lock signal is detected 1.2 seconds or more while the fan operation.
Remedy:	A: A-1. Power supply fan is faulty. A-2. Connector of the power supply fan is disconnected B: B-1. The connector of the power supply fan (FAN101) is disconnected. B-2. The wiring of the power supply fan is faulty. B-3. The power supply fan is faulty. B-4. The finisher controller PCB is faulty.

Error code:	E551-0002
Description:	A. Error in power supply fan (Paper Folding Unit) B. Error in power supply fan (FAN101) (Finisher). The lock status is released when the fan stops.
Remedy:	A: A-1. Connector of the power supply fan is disconnected. A-2. Power supply fan is faulty. B: B-1. The connector of the power supply fan (FAN101) is disconnected. B-2. The wiring of the power supply fan is faulty. B-3. The power supply fan is faulty. B-4. The finisher controller PCB is faulty.

Error code:	E551-0011
Description:	Error in the power supply fan of the insertion unit. The loch signal is detected for the specified period of times while the fan operates.
Remedy:	1. The connector of the fan (F1) is disconnected. 2. The wiring of the fan is faulty. 3. The fan is faulty. 4. The insertion unit controller PCB is faulty.

Error code:	E551-0021
Description:	Error in the fan of the paper folding unit. The loch signal is detected for the specified period of times while the fan operates.
Remedy:	1. The connector of the fan (F1) is disconnected. 2. The wiring of the fan is faulty. 3. The fan is faulty. 4. The paper folding unit controller PCB is faulty.

Error code:	E562-8001
Description:	Error in slowing timing sensor (Paper folding unit (Document Insertion Folding Unit/Paper Folding Unit). The receiving-light intensity failed to be within the threshold although the emitting-light intensity is adjusted to be within the threshold when adjusting the sensor.
Remedy:	1. Connector of the slowing timing sensor (S24/S30) is disconnected. 2. Slowing timing sensor is faulty

Error code:	E562-8002
Description:	Error in the disengagement timing sensor of paper folding unit (Document Insertion Folding Unit/Paper Folding Unit). The disengagement timing sensor (S21) adjustment failed.
Remedy:	1. Connector of the disengagement timing sensor (S21) is disconnected. 2. Disengagement timing sensor is faulty.

Error code:	E562-8003
Description:	Error in the folding position accuracy sensor (Document Insertion Folding Unit/Paper Folding Unit). The folding position accuracy sensor (S23) adjustment failed.
Remedy:	1. Connector of the folding position accuracy sensor (S23) is disconnected. 2. Folding position accuracy sensor is faulty.

Error code:	E562-8004
Description:	Error in the upper stopper HP sensor (Document Insertion Folding Unit/Paper Folding Unit). The upper stopper HP sensor (S16) adjustment failed.
Remedy:	1. Connector of the upper stopper HP sensor (S16) is disconnected. 2. Upper stopper HP sensor is faulty.

Error code:	E568-8001
Description:	Error in the feed roller disengage/buffer flapper motor (Finisher-K1). The disengage roller does not come off the feed roller separation HP sensor when the feed roller disengage/ buffer flapper motor has been driven for 3 seconds.
Remedy:	1. The connector of the feed roller separation HP sensor (S111) or the feed roller disengage/buffer flapper motor (M119) are disconnected. 2. The wiring of the feed roller separation HP sensor or the feed roller disengage/buffer flapper motor are faulty. 3. The feed roller separation HP sensor is faulty. 4. The feed roller disengage/buffer flapper motor is faulty. 5. The finisher controller PCB is faulty

Error code:	E568-8002
Description:	Error in the feed roller disengage/buffer flapper motor (Finisher-K1). The feed roller separation HP sensor does not detect the disengage roller when the feed roller disengage/buffer flapper motor has been driven for 3 seconds.
Remedy:	1. The connector of the feed roller separation HP sensor (S111) or the feed roller disengage/buffer flapper motor (M119) are disconnected. 2. The wiring of the feed roller separation HP sensor or the feed roller disengage/buffer flapper motor are faulty. 3. The feed roller separation HP sensor is faulty. 4. The feed roller disengage/buffer flapper motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E568-8003
Description:	Error in the feed roller disengage/buffer flapper motor (Finisher-K1). The buffer flapper does not come off the buffer flapper HP sensor when the feed roller disengage/buffer flapper motor has been driven for 3 seconds.
Remedy:	1. The connector of the buffer flapper HP sensor (S142) or the feed roller disengage/buffer flapper motor (M119) are disconnected. 2. The wiring of the buffer flapper HP sensor or the feed roller disengage/buffer flapper motor are faulty. 3. The buffer flapper HP sensor is faulty. 4. The feed roller disengage/buffer flapper motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E568-8004
Description:	Error in the feed roller disengage/buffer flapper motor (Finisher-K1). The buffer flapper HP sensor does not detect the buffer flapper when the feed roller disengage/buffer flapper motor has been driven for 3 seconds.
Remedy:	1. The connector of the buffer flapper HP sensor (S142) or the feed roller disengage/buffer flapper motor (M119) are disconnected. 2. The wiring of the buffer flapper HP sensor or the feed roller disengage/buffer flapper motor are faulty. 3. The buffer flapper HP sensor is faulty. 4. The feed roller disengage/buffer flapper motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E569-8001
Description:	Upper stopper motor of paper folding unit failed to go through HP (Document Insertion Folding Unit/Paper Folding Unit). The upper stopper HP sensor (S16) failed to be OFF despite the drive of specified pulse in the case that the upper stopper motor started to be driven while the upper stopper HP sensor was ON.
Remedy:	1. Connector of the upper stopper motor (M7) is disconnected. 2. Upper stopper motor is faulty. 3. Connector of the upper stopper HP sensor (S16) is disconnected. 4. Upper stopper HP sensor is faulty

Error code:	E569-8002
Description:	Upper stopper motor of paper folding unit failed to return to HP (Document Insertion Folding Unit/Paper Folding Unit). The upper stopper HP sensor (S16) failed to be ON despite the drive of specified pulse in the case that the upper stopper motor started to be driven while the upper stopper HP sensor was OFF.
Remedy:	1. Connector of the upper stopper motor (M7) is disconnected. 2. Upper stopper motor is faulty. 3. Connector of the upper stopper HP sensor (S16) is disconnected. 4. Upper stopper HP sensor is faulty.

Error code:	E56A-8001
Description:	C-fold stopper motor of paper folding unit failed to go through HP (Document Insertion Folding Unit/Paper Folding Unit). The C-fold stopper motor HP sensor (S17) failed to be OFF despite the drive of specified pulse in the case that the C-fold stopper motor started to be driven while the C-fold stopper motor HP sensor was ON.
Remedy:	1. Connector of the C-fold stopper motor (M8) is disconnected. 2. C-fold stopper motor is faulty. 3. Connector of the C-fold stopper HP sensor (S17) is disconnected. 4. C-fold stopper HP sensor is faulty.

Error code:	E56A-8002
Description:	C-fold stopper motor of paper folding unit failed to return to HP (Document Insertion Folding Unit/Paper Folding Unit). The C-fold stopper motor HP sensor (S17) failed to be ON despite the drive of specified pulse in the case that the C-fold stopper motor started to be driven while the C-fold stopper motor HP sensor was OFF
Remedy:	1. Connector of the C-fold stopper motor (M8) is disconnected. 2. C-fold stopper motor is faulty. 3. Connector of the C-fold stopper HP sensor (S17) is disconnected. 4. C-fold stopper HP sensor is faulty.

Error code:	E56B-8001
Description:	Folding belt motor of paper folding unit failed to go through HP (Document InsertionFolding Unit/Paper Folding Unit). During initialization or at paper delivery to the Folding upper tray, the Folding belt HP sensor has not turned OFF within the specified pulse.
Remedy:	1. Connector of the Folding belt motor is disconnected. 2. Folding belt motor is faulty. 3. Connector of the Folding belt motor HP sensor is disconnected. 4. Folding belt motor HP sensor is faulty.

Error code:	E56B-8002
Description:	Folding tray motor of paper folding unit failed to return to HP (Document Insertion Folding Unit/Paper Folding Unit). During initialization or at paper delivery to the Folding upper tray, the Folding tray motor HP sensor has not turned ON within the specified pulse.
Remedy:	1. Connector of the folding tray motor (M6) is disconnected. 2. Folding tray motor is faulty. 3. Connector of the folding tray motor HP sensor (S19) is disconnected. 4. Folding tray motor HP sensor is faulty.

Error code:	E56D-8001
Description:	Error in the stacking tray paper retainer motor (Finisher-K1). The stacking tray paper retainer does not come off the stacking tray paper retainer HP sensor when the stacking tray paper retainer motor has been driven for 3 seconds.
Remedy:	1. The connector of the stacking tray paper retainer HP sensor (S114) or the stacking tray paper retainer motor (M114) are disconnected. 2. The wiring of the stacking tray paper retainer HP sensor or the stacking tray paper retainer motor are faulty. 3. The stacking tray paper retainer HP sensor is faulty. 4. The stacking tray paper retainer motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E56D-8002
Description:	Error in the stacking tray paper retainer motor (Finisher-K1). The stacking tray paper retainer HP sensor does not detect the stacking tray paper retainer when the stacking tray paper retainer motor has been driven for 3 seconds.
Remedy:	1. The connector of the stacking tray paper retainer HP sensor (S114) or the stacking tray paper retainer motor (M114) are disconnected. 2. The wiring of the stacking tray paper retainer HP sensor or the stacking tray paper retainer motor are faulty. 3. The stacking tray paper retainer HP sensor is faulty. 4. The stacking tray paper retainer motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E56E-8001
Description:	Lead-edge retaining guide motor of paper folding unit failed to go through HP (Paper Folding Unit). The lead-edge retaining guide HP sensor failed to be OFF despite the drive of specified pulse in the case that the lead-edge retaining guide motor started to be driven while the lead-edge retaining guide HP sensor was ON.
Remedy:	1. Connector of the lead-edge retaining guide motor (M10) is disconnected. 2. Lead-edge retaining guide motor is faulty. 3. Connector of the lead-edge retaining guide HP sensor (S25) is disconnected. 4. Lead-edge retaining guide HP sensor is faulty.

Error code:	E56E-8002
Description:	Lead-edge retaining guide motor of paper folding unit failed to return to HP (Paper Folding Unit). The lead-edge retaining guide HP sensor failed to be ON despite the drive of specified pulse in the case that the lead-edge retaining guide motor started to be driven while the lead-edge retaining guide HP sensor was OFF.
Remedy:	1. Connector of the lead-edge retaining guide motor (M10) is disconnected. 2. Lead-edge retaining guide motor is faulty. 3. Connector of the lead-edge retaining guide HP sensor (S25) is disconnected. 4. Lead-edge retaining guide HP sensor is faulty.

Error code:	E578-8001
Description:	Error in the paper return guide motor (Finisher-K1). The paper return guide does not come off the paper return guide HP sensor when the paper return guide motor has been driven for 3 seconds.
Remedy:	1. The connector of the paper return guide HP sensor (S112) or the paper return guide motor (M112) are disconnected. 2. The wiring of the paper return guide HP sensor or the paper return guide motor are faulty. 3. The paper return guide HP sensor is faulty. 4. The paper return guide motor is faulty. 5. The finisher controller PCB is faulty

Error code:	E578-8002
Description:	Error in the paper return guide motor (Finisher-K1). The paper return guide HP sensor does not detect the paper return guide when the paper return guide motor has been driven for 3 seconds
Remedy:	1. The connector of the paper return guide HP sensor (S112) or the paper return guide motor (M112) are disconnected. 2. The wiring of the paper return guide HP sensor or the paper return guide motor are faulty. 3. The paper return guide HP sensor is faulty. 4. The paper return guide motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E57B-8001
Description:	Error in the paper trailing edge pushing guide motor (Finisher-K1). The paper trailing edge pushing guide does not come off the paper trailing edge pushing guide HP sensor when the paper trailing edge pushing guide motor has been driven for 3 seconds
Remedy:	1. The connector of the paper trailing edge pushing guide HP sensor (S113) or the paper trailing edge pushing guide motor (M113) are disconnected. 2. The wiring of the paper trailing edge pushing guide HP sensor or the paper trailing edge pushing guide motor are faulty. 3. The paper trailing edge pushing guide HP sensor is faulty. 4. The paper trailing edge pushing guide motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E57B-8002
Description:	Error in the paper trailing edge pushing guide motor (Finisher-K1). The paper trailing edge pushing guide HP sensor does not detect the paper trailing edge pushing guide when the paper trailing edge pushing guide motor has been driven for 3 seconds.
Remedy:	1. The connector of the paper trailing edge pushing guide HP sensor (S113) or the paper trailing edge pushing guide motor (M113) are disconnected. 2. The wiring of the paper trailing edge pushing guide HP sensor or the paper trailing edge pushing guide motor are faulty. 3. The paper trailing edge pushing guide HP sensor is faulty. 4. The paper trailing edge pushing guide motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E57C-8001
Description:	Error in the processing tray paper retainer motor (Finisher-K1). The paper retainer does not come off the paper retainer HP sensor when the processing tray paper retainer motor has been driven for 3 seconds.
Remedy:	1. The connector of the paper retainer HP sensor (S135) or the processing tray paper retainer motor (M118) are disconnected. 2. The wiring of the paper retainer HP sensor or the processing tray paper retainer motor are faulty. 3. The paper retainer HP sensor is faulty. 4. The processing tray paper retainer motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E57C-8002
Description:	Error in the processing tray paper retainer motor (Finisher-K1). The paper retainer HP sensor does not detect the paper retainer when the processing tray paper retainer motor has been driven for 3 seconds.
Remedy:	1. The connector of the paper retainer HP sensor (S135) or the processing tray paper retainer motor (M118) are disconnected. 2. The wiring of the paper retainer HP sensor or the processing tray paper retainer motor are faulty. 3. The paper retainer HP sensor is faulty. 4. The processing tray paper retainer motor is faulty. 5. The finisher controller PCB is faulty.

Error code:	E583-8001
Description:	Error in the tray auxiliary guide motor (Finisher-K1). The tray auxiliary guide does not come off the tray auxiliary guide front/rear HP sensors when the tray auxiliary guide motor has been driven for 3 seconds
Remedy:	1. The connector of the tray auxiliary guide front HP sensor (S137) or the tray auxiliary guide rear HP sensor (S136) are disconnected. 2. The connector of the tray auxiliary guide motor (M120) is disconnected. 3. The wiring of the tray auxiliary guide front HP sensor or the tray auxiliary guide rear HP sensor are faulty. 4. The wiring of the tray auxiliary guide motor is faulty. 5. The tray auxiliary guide front HP sensor is faulty. 6. The tray auxiliary guide rear HP sensor is faulty. 7. The tray auxiliary guide motor is faulty. 8. The finisher controller PCB is faulty.

Error code:	E583-8002
Description:	Error in the tray auxiliary guide motor (Finisher-K1). The tray auxiliary guide front/rear HP sensors does nor detect the tray auxiliary guide when the tray auxiliary guide motor has been driven for 3 seconds.
Remedy:	1. The connector of the tray auxiliary guide front HP sensor (S137) or the tray auxiliary guide rear HP sensor (S136) are disconnected. 2. The connector of the tray auxiliary guide motor (M120) is disconnected. 3. The wiring of the tray auxiliary guide front HP sensor or the tray auxiliary guide rear HP sensor are faulty. 4. The wiring of the tray auxiliary guide motor is faulty. 5. The tray auxiliary guide front HP sensor is faulty. 6. The tray auxiliary guide rear HP sensor is faulty. 7. The tray auxiliary guide motor is faulty. 8. The finisher controller PCB is faulty.

Error code:	E584-0002
Description:	- Shutter drive motor or finisher controller PCB failure - Shutter open detection sensor failure - Shutter clutch failure - The shutter open sensor did not turn off when 1000 ms have lapsed since the shutter unit had performed close operation, resulting in incomplete close operation.
Causes:	The feed motor (M1) is faulty. The shutter open sensor (PI5) is faulty.
Remedy:	- Check the connector of the shutter open sensor. - Check the connector of the shutter clutch. - Check the connector of the shutter motor. - Replace the shutter open sensor. - Replace the shutter clutch. - Replace the shutter drive motor. - Replace the finisher controller PCB.

Error code:	E584-8001
Description:	Tray unit trouble When the shutter fails to leave the shutter home position even when the binding motor has been driven for 3 sec.
Remedy:	- Check the shutter home position sensor connectors. - Replace the shutter home position sensor. - Replace the shutter open/close clutch (CL101). - Replace the binding bottom roller clutch (CL102). - Replace the binding motor (M102).

Error code:	E584-8003
Description:	Error in the stack delivery lower/shutter motor (Finisher-K1). The shutter does not come off the shutter close detection sensor when the stack delivery lower/shutter motor has been driven for 3 seconds.
Remedy:	1. The connector of the shutter close detection sensor (S148)/the stack delivery lower/shutter motor (M122) are disconnected. 2. The wiring of the shutter close detection sensor / the stack delivery lower/shutter motor are faulty. 3. The shutter close detection sensor is faulty. 4. The stack delivery lower/shutter motor is faulty. 5. The finisher controller PCB is faulty

Error code:	E584-8004
Description:	Error in the stack delivery lower/shutter motor (Finisher-K1). The shutter close detection sensor does not detect the shutter when the stack delivery lower/shutter motor has been driven for 3 seconds.
Remedy:	1. The connector of the shutter close detection sensor (S148)/the stack delivery lower/shutter motor (M122) are disconnected. 2. The wiring of the shutter close detection sensor / the stack delivery lower/shutter motor are faulty. 3. The shutter close detection sensor is faulty. 4. The stack delivery lower/shutter motor is faulty. 5. The finisher controller PCB is faulty

Error code:	E590-8001
Description:	When the puncher cannot detect the punch home position sensor even when the punch motor is driven for 200 ms
Remedy:	- Check the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch motor (M61).

Error code:	E590-8002
Description:	When the puncher cannot detect the punch home position sensor after motor drive has stopped during the initial operation of the punch motor
Remedy:	- Check the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch home position sensor (P163) and punch motor clock sensor (P162) connectors. - Replace the punch motor (M61).

Error code:	E590-8003
Description:	Error in the Punch motor (Finisher-K1). The puncher does not come off the punch HP sensor when the punch motor has been driven for 0.2 second. The puncher does not come off the punch HP sensor during initialization.
Remedy:	1. The connector of the punch HP sensor (S104)/the punch motor clock sensor (S105) are disconnected. 2. The connector of the punch motor (M102) is disconnected. 3. The wiring of the punch HP sensor or the punch motor clock sensor are faulty. 4. The wiring of the punch motor is faulty. 5. The punch HP sensor is faulty. 6. The punch motor clock sensor is faulty. 7. The punch motor is faulty. 8. The puncher driver PCB (PCB1) is faulty. 9. The finisher controller PCB is faulty

Error code:	E593-8001
Description:	Side registration initializing error When the side registration fails to leave the side registration home position sensor position even when the punch slide unit is moved 9 mm during the initial operation of the side registration motor
Remedy:	- Check the side registration home position sensor (P161) connectors. - Replace the side registration home position sensor (P161). - Replace the side registration motor (M62).

Error code:	E593-8002
Description:	Side registration initializing error When the side registration fails to return to the side registration home position sensor position even when the punch slide unit is moved 37 mm during the initial operation of the side registration motor
Remedy:	- Check the side registration home position sensor (P161) connectors. - Replace the side registration home position sensor (P161). - Replace the side registration motor (M62).

Error code:	E5A3-0001
Description:	Error in the registration motor (Finisher-K1). The registration HP sensor does not turn ON when the registration motor has been driven for 2.933 seconds.
Remedy:	1. The connector of the registration HP sensor (S105) or the registration motor (M102) are disconnected. 2. The wiring of the registration HP sensor/the registration motor are faulty. 3. The registration HP sensor is faulty. 4. The registration motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5A3-0002
Description:	Error in the registration motor (Finisher-K1). The registration HP sensor does not turn OFF when the registration motor has been driven for 0.67 msecond.
Remedy:	1. The connector of the registration HP sensor (S105) or the registration motor (M102) are disconnected. 2. The wiring of the registration HP sensor/the registration motor are faulty. 3. The registration HP sensor is faulty. 4. The registration motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5A4-8001
Description:	Error in the press motor (Finisher-K1). The press motor HP sensor does not turn ON when the press motor has been driven for 0.926 second.
Remedy:	1. The connector of the press motor HP sensor (S106) or the press motor (M105) are disconnected. 2. The wiring of the press motor HP sensor/the press motor are faulty. 3. The press motor HP sensor is faulty. 4. The press motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5A4-8002
Description:	Error in the press motor (Finisher-K1). The press motor HP sensor does not turn OFF.
Remedy:	1. The connector of the press motor HP sensor (S106) or the press motor (M105) are disconnected. 2. The wiring of the press motor HP sensor/the press motor are faulty. 3. The press motor HP sensor is faulty. 4. The press motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5AA-8001
Description:	Error in the cutter motor (Finisher-K1). The home position of the trimming blade is not detected when the cutter motor has been driven for 5 sec.
Remedy:	1. The connector of the cutter motor clock sensor (S108) or the cutter motor (M106) are disconnected. 2. The wiring of the cutter motor clock sensor/the cutter motor are faulty. 3. The cutter motor clock sensor is faulty. 4. The cutter motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5AA-8002
Description:	Error in the cutter motor (Finisher-K1). The cutter motor clock sensor does not come off the home position of the trimming blade when the cutter motor has been driven for 0.5 second.
Remedy:	1. The connector of the cutter motor clock sensor (S108) or the cutter motor (M106) are disconnected. 2. The wiring of the cutter motor clock sensor/the cutter motor are faulty. 3. The cutter motor clock sensor is faulty. 4. The cutter motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5AA-8003
Description:	Cutter motor clock error (Finisher-K1). The cutter motor clock sensor does not detect the motor clock when the cutter motor has been driven for 0.625 second.
Remedy:	1. The connector of the cutter motor clock sensor (S108) or the cutter motor (M106) are disconnected. 2. The wiring of the cutter motor clock sensor/the cutter motor are faulty. 3. The cutter motor clock sensor is faulty. 4. The cutter motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5AE-8000
Description:	Trimmer stationary paper error. The inlet sensor detects the stationary paper after performing the paper delivery operation.
Remedy:	1. The paper has jammed in the trimmer. 2. The connector of the inlet sensor (S101) is disconnected. 3. The wire of the inlet sensor is faulty. 4. The inlet sensor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5BA-8001
Description:	Error in the front estrangement motor (Finisher-K1). The front estrangement motor HP sensor does not turn ON when the front estrangement motor has been driven for 0.191 second.
Remedy:	1. The connector of the front estrangement motor HP sensor (S102) or the front estrangement motor (M103) are disconnected. 2. The wiring of the front estrangement motor HP sensor/ the front estrangement motor are faulty. 3. The front estrangement motor HP sensor is faulty. 4. The front estrangement motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5BA-8002
Description:	Error in the front estrangement motor (Finisher-K1). The front estrangement motor HP sensor does not turn OFF when the front estrangement motor has been driven for 0.724 second after the front estrangement motor HP sensor has turned ON.
Remedy:	1. The connector of the front estrangement motor HP sensor (S102) or the front estrangement motor (M103) are disconnected. 2. The wiring of the front estrangement motor HP sensor/ the front estrangement motor are faulty. 3. The front estrangement motor HP sensor is faulty. 4. The front estrangement motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5BA-8011
Description:	Error in the rear estrangement motor (Finisher-K1). The rear estrangement motor HP sensor does not turn ON when the rear estrangement motor has been driven for 0.18 second.
Remedy:	1. The connector of the rear estrangement motor HP sensor (S104) or the rear estrangement motor (M104) are disconnected. 2. The wiring of the rear estrangement motor HP sensor/ the rear estrangement motor are faulty. 3. The rear estrangement motor HP sensor is faulty. 4. The rear estrangement motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty

Error code:	E5BA-8012
Description:	Error in the rear estrangement motor (Finisher-K1). The rear estrangement motor HP sensor does not turn OFF when the rear estrangement motor has been driven for 0.537 second.
Remedy:	1. The connector of the rear estrangement motor HP sensor (S104) or the rear estrangement motor (M104) are disconnected. 2. The wiring of the rear estrangement motor HP sensor/ the rear estrangement motor are faulty. 3. The rear estrangement motor HP sensor is faulty. 4. The rear estrangement motor is faulty. 5. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5BB-8001
Description:	Error in the waste paper full sensor (Finisher-K1). The A/D input value does not enter into the D/A output upper limit of the waste paper full sensor
Remedy:	1. The connector of the waste paper full sensor (emitting/ receiving) (S011) is disconnected. 2. The wire of the waste paper full sensor is faulty. 3. The waste paper full sensor is faulty. 4. The trimmer controller PCB (PCB1) is faulty.

Error code:	E5BB-8002
Description:	Error in the waste paper full sensor (Finisher-K1). The A/D input value does not enter into the D/A output lower limit of the waste paper full sensor.
Remedy:	1. The connector of the waste paper full sensor (emitting/ receiving) (S011) is disconnected. 2. The wire of the waste paper full sensor is faulty. 3. The waste paper full sensor is faulty. 4. The trimmer controller PCB (PCB1) is faulty

Error code:	E5F0-8001
Description:	Saddle sheet positioning error When the sheet positioning plate home position sensor fails to turn ON even when the sheet positioning plate motor is driven by 1500 pulses
Remedy:	- Check the sheet positioning plate home position sensor (P17) connectors. - Replace the sheet positioning plate home position sensor (P17). - Replace the sheet positioning plate motor (M4).

Error code:	E5F0-8002
Description:	Saddle sheet positioning error When the sheet positioning plate home position sensor fails to turn OFF even when the sheet positioning plate motor is driven by 300 pulses
Remedy:	- Check the sheet positioning plate home position sensor (P17) connectors. - Replace the sheet positioning plate home position sensor (P17). - Replace the sheet positioning plate motor (M4).

Error code:	E5F1-8001
Description:	Saddle sheet creasing error When the number of detection pulses of the sheet creasing motor clock sensor has dropped below the prescribed number
Remedy:	- Check the sheet creasing motor clock sensor (P14) and sheet creasing home position sensor (P121) connectors. - Replace the sheet creasing motor clock sensor (P14) and sheet creasing home position sensor (P121). - Replace the sheet creasing motor (M2).

Error code:	E5F1-8002
Description:	Saddle sheet creasing error When the sheet creasing home position sensor status fails to change even when the sheet creasing motor is driven for 3 sec.
Remedy:	When the sheet creasing home position sensor status fails to change even when the sheet creasing motor is driven for 3 sec.

Error code:	E5F2-8001
Description:	Saddle guide error The guide HP sensor fails to be ON after the guide motor is driven for 0.455 sec.
Remedy:	Replace the guide motor (M3S), Replace the guide HP sensor (PI13S)

Error code:	E5F2-8002
Description:	Saddle guide error The HP sensor fails to be OFF after the guide motor is driven for 1 sec.
Remedy:	Replace the guide motor (M3S), Replace the guide HP sensor (PI13S)

Error code:	E5F3-8001
Description:	Saddle alignment error When the alignment plate home position sensor fails to turn ON even when the alignment motor is driven for 0.5 sec. (or driven for 1.67 sec. during the initial operation)
Remedy:	- Check the alignment plate home position sensor (P15S) connectors. - Replace the alignment plate home position sensor (P15S). - Replace the alignment motor (M5S).

Error code:	E5F3-8002
Description:	Saddle alignment error When the alignment plate home position sensor fails to turn OFF even when the alignment motor is driven for 1 sec.
Remedy:	- Check the alignment plate home position sensor (P15S) connectors. - Replace the alignment plate home position sensor (P15S). - Replace the alignment motor (M5S).

Error code:	E5F4-8001
Description:	Saddle rear stapler error When the stitch operation home position sensor fails to turn OFF even when the stitch motor (rear) has been run in the forward direction for at least 0.5 sec.
Remedy:	- Check the stitch operation home position sensor (rear, MS5S) connectors. - Replace the stitch operation home position sensor (rear, MS5S). - Replace the stitch motor (rear, M6S).

Error code:	E5F4-8002
Description:	Saddle rear stapler error When the stitch operation home position sensor fails to turn ON even when the stitch motor (rear) has been run in the reverse direction for at least 0.5 sec.
Remedy:	- Check the stitch operation home position sensor (rear, MS5S) connectors. - Replace the stitch operation home position sensor (rear, MS5S). - Replace the stitch motor (rear, M6S).

Error code:	E5F5-8001
Description:	Saddle front stapler error When the stitch operation home position sensor fails to turn OFF even when the stitch motor (front) has been run in the forward direction for at least 0.5 sec.
Remedy:	- Check the stitch operation home position sensor (front, MS7S) connectors. - Replace the stitch operation home position sensor (front, MS7S). - Replace the stitch motor (front, M7S).

Error code:	E5F5-8002
Description:	Saddle front stapler error When the stitch operation home position sensor fails to turn ON even when the stitch motor (front) has been run in the reverse direction for at least 0.5 sec.
Remedy:	- Check the stitch operation home position sensor (front, MS7S) connectors. - Replace the stitch operation home position sensor (front, MS7S). - Replace the stitch motor (front, M7S).

Error code:	E5F6-8001
Description:	Saddle sheet push plate stapler error When the sheet push plate home position sensor fails to turn ON even when the sheet push plate motor has been run for at least 0.3 sec.
Remedy:	- Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S).

Error code:	E5F6-8002
Description:	Saddle sheet push plate stapler error When the sheet push plate home position sensor fails to turn OFF even when the sheet push plate motor has been run for at least 80 ms
Remedy:	- Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S).

Error code:	E5F6-8003
Description:	Saddle sheet push plate stapler error When the sheet push plate edge position sensor fails to turn OFF even when the sheet push plate motor has been run for at least 80 ms
Remedy:	- Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S).

Error code:	E5F7-8001
Description:	Error in the saddle trailing edge retainer motor (Finisher-K1). The saddle trailing edge retainer HP sensor does not detect the saddle trailing edge retainer when the saddle trailing edge retainer motor has been driven for 80 pulses.
Remedy:	1. The connector of the saddle trailing edge retainer HP sensor (S221) or the saddle trailing edge retainer motor (M210) are disconnected. 2. The wiring of the saddle trailing edge retainer HP sensor/the saddle trailing edge retainer motor are faulty. 3. The saddle trailing edge retainer HP sensor is faulty. 4. The saddle trailing edge retainer motor is faulty. 5. The saddle stitcher controller PCB is faulty. 6. The finisher controller PCB is faulty.

Error code:	E5F7-8002
Description:	Error in the saddle trailing edge retainer motor (Finisher-K1). The saddle trailing edge retainer does not come off the saddle trailing edge retainer HP sensor when the saddle trailing edge retainer motor has been driven for 50 pulses.
Remedy:	1. The connector of the saddle trailing edge retainer HP sensor (S221) or the saddle trailing edge retainer motor (M210) are disconnected. 2. The wiring of the saddle trailing edge retainer HP sensor/the saddle trailing edge retainer motor are faulty. 3. The saddle trailing edge retainer HP sensor is faulty. 4. The saddle trailing edge retainer motor is faulty. 5. The saddle stitcher controller PCB is faulty. 6. The finisher controller PCB is faulty.

Error code:	E5F8-8001
Description:	Saddle connector error Disconnection of the guide HP sensor connector is detected.
Remedy:	Disconnect and then connect the guide HP sensor (PI13S) connector

Error code:	E5F8-8002
Description:	Saddle connector error Disconnection of the paper pressure plate HP sensor connector is detected.
Remedy:	Disconnect and then connect the paper pressure plate HP sensor (PI14S) connector

Error code:	E5F9-8001
Description:	Saddle switch error When the entrance door switch is in the open status even when all the covers are closed
Remedy:	- Check the entrance door switch (MSW1), delivery door switch (MSW3) and front cover close detection switch (MSW101). - Replace the entrance door switch (MSW1), delivery door switch (MSW3) and front cover close detection switch (MSW101).

Error code:	E5F9-8002
Description:	Saddle switch error When the delivery door switch is in the open status even when all the covers are closed
Remedy:	- Check the entrance door switch (MSW1), delivery door switch (MSW3) and front cover close detection switch (MSW101). - Replace the entrance door switch (MSW1), delivery door switch (MSW3) and front cover close detection switch (MSW101).

Error code:	E602-0001
Description:	HDD error
Causes:	Lack of the HDD capacity The capacity of the HDD installed is smaller than that of the HDD used in the software.

Error code:	E602-0002
Description:	HDD error
Causes:	Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged.
Remedy:	Burn the Bootable CD again.

Error code:	E602-0003
Description:	HDD error
Causes:	HDD access error An error occurred caused by the device or hardware when accessing to the HDD during execution of bootrom. (Damage to the sector / Busy device status, etc.)
Remedy:	Turn on the power again.

Error code:	E602-0006
Description:	HDD error
Causes:	SubBootable load failure A SubBootable CD was not contained. A SubBootable CD was damaged.
Remedy:	Burn the SubBootable CD again.

Error code:	E602-0009
Description:	MEAP cannot be started.
Causes:	MEAP cannot be started due to an error caused by invalid power down.
Remedy:	1. Select Function.gr > MEAP > MEAP FUNCTION = ON, and turn OFF and then ON the main power. * Since the installed MEAP application and its management information are all cleared after reboot, MEAP needs to be reinstalled.

Error code:	E602-0012
Description:	Error in HDD. There is no file in which the Web browser refers to
Remedy:	1. Start up in Safe Mode and reinstall the Web browser using SST, and then turn OFF and then ON the main power switch. 2. If the above measures do not solve the problem, it can be caused by failure with the HDD; therefore, replace the HDD and reinstall the system.

Error code:	E602-0100
Description:	Hard disk failure.
Remedy:	1. Check a cable or power supply connector 2. If not recovery, boot-up in safe mode, and use SST to execute full-format and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure

Error code:	E602-0101
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	1. Check a cable or power supply connector 2. If not recovery, boot-up in safe mode, and use SST to execute full-format and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure

Error code:	E602-0102
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	1. Check a cable or power supply connector 2. If not recovery, boot-up in safe mode, and use SST to execute full-format and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0103
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	1. Input applicable CHK-TYPE into a partition; and execute HDD-CHECK (requires several minutes to some dozens of minutes); and then ower cycle (Power OFF/ON) 2. If not recovery, input applicable CHK-TYPE into a partition; and execute HDD-CLEAR; and then power cycle (Power OFF/ON)

Error code:	E602-0104
Description:	Hard disk failure.
Remedy:	1. Check a cable or power supply connector 2. If not recovery, boot-up in safe mode, and use SST to execute full-format and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0105
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	1. input applicable CHK-TYPE into a partition; and execute HDD-CLEAR; and then power cycle (Power OFF/ON) 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0110
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	This is an error due to data error or software bug. 1. Boot-up in safe mode, and use SST to execute fullformat and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0111
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	This is an error that usually does not occur at Read/Write level. 1. Check a cable or power supply connector 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0112
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	This is an error due to data error or software bug. 1. Boot-up in safe mode, and use SST to execute fullformat and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0113
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	It is very likely that document data such as BOX on the HDD are damaged. 1. Input applicable CHK-TYPE into a partition; and execute HDD-CHECK (requires several minutes to some dozens of minutes); and then power cycle. 2. If not recovery, input applicable CHK-TYPE into a partition; and execute HDD-CLEAR; and then power cycle (in the case of BOOTDEV, BOOTDEV2, APL_SEND, execute re-format / reinstallation with SST) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0114
Description:	Hard disk failure. FSTDEV is abnormal
Remedy:	This is an error due to data error or software bug. 1. Boot-up in safe mode, and use SST to execute fullformat and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0121
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	This is an error that usually does not occur at Read/Write level. 1. Check a cable or power supply connector 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0122
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	This is an error due to data error or software bug. 1. Boot-up in safe mode, and use SST to execute fullformat and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0123
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	This is an error due to data error or software bug. 1. Boot-up in safe mode, and use SST to execute fullformat and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0124
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	This is an error due to data error or software bug. 1. Boot-up in safe mode, and use SST to execute fullformat and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 2. If not recovery, replace HDD and re-install system based on judging HDD failure

Error code:	E602-0125
Description:	Hard disk failure. /FSTDEV is abnormal
Remedy:	It is very likely that document data such as BOX on the HDD are damaged. 1. Input applicable CHK-TYPE into a partition; and execute HDD-CHECK (requires several minutes to some dozens of minutes); and then power cycle 2. If not recovery, input applicable CHK-TYPE into a partition; and execute HDD-CLEAR; and then power cycle (in the case of BOOTDEV, BOOTDEV2, APL_SEND, execute re-format / reinstallation with SST) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0200
Description:	Hard disk failure. /IMG_MNG is abnormal
Remedy:	1. Check a cable or power supply connector 2. If not recovery, Boot-up in safe mode, and use SST to execute full-format and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0201
Description:	Hard disk failure. /IMG_MNG is abnormal
Remedy:	1. Check a cable or power supply connector 2. If not recovery, Boot-up in safe mode, and use SST to execute full-format and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0202
Description:	Hard disk failure. /IMG_MNG is abnormal
Remedy:	1. Check a cable or power supply connector 2. If not recovery, Boot-up in safe mode, and use SST to execute full-format and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0203
Description:	Hard disk failure. /IMG_MNG is abnormal
Remedy:	1. Input applicable CHK-TYPE into a partition; and execute HDD-CHECK (requires several minutes to some dozens of minutes); and then power cycle 2. If not recovery, input applicable CHK-TYPE into a partition; and execute HDD-CLEAR; and then power cycle

Error code:	E602-0204
Description:	Hard disk failure. /IMG_MNG is abnormal
Remedy:	1. Check a cable or power supply connector 2. If not recovery, Boot-up in safe mode, and use SST to execute full-format and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 3. If still not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0205
Description:	Hard disk failure. /IMG_MNG is abnormal
Remedy:	1. input applicable CHK-TYPE into a partition; and execute HDD-CLEAR; and then power cycle 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0210
Description:	Hard disk failure. /IMG_MNG is abnormal
Remedy:	This is an error due to data error or software bug. 1. Boot-up in safe mode, and use SST to execute fullformat and to re-install system (SYSTEM, LANGUAGE, RUI); and then power cycle of main power (Power OFF/ON) 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0211
Description:	Hard disk failure. /IMG_MNG is abnormal
Remedy:	This is an error that usually does not occur at Read/Write level. 1. Check a cable or power supply connector 2. If not recovery, replace HDD and re-install system based on judging HDD failure.

Error code:	E602-0212
Description:	Hard disk error. Error in /IMG_MNG.
Remedy:	Error due to data corruption or software bug. 1. Start up in Safe Mode to perform All Format using SST and reinstall the system (SYSTEM, LANGUAGE, RUI), and then turn OFF and then ON the main power. 2. If the measures above do not solve the problem, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0213
Description:	Hard disk error. Error in /IMG_MNG.
Remedy:	The document data (such as Box on the HDD) can be damaged. 1. Enter the corresponding CHK-TYPE in the partition to execute HDD-CHECK (duration: several minutes to several dozen minutes); and then turn OFF and then ON the power. 2. If the measures above do not solve the problem, enter the corresponding CHK-TYPE in the partition to execute HDDCLEAR, and then turn OFF and then ON the main power. (Use SST to perform reformat/reinstallation in the case of the following: BOOTDEV, BOOTDEV2 and APL_SEND) 3. If the error still remains, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0214
Description:	Hard disk error. Error in /IMG_MNG.
Remedy:	Error due to data corruption or software bug. 1. Start up in Safe Mode to perform All Format using SST and reinstall the system (SYSTEM, LANGUAGE, RUI), and then turn OFF and then ON the main power. 2. If the measures above do not solve the problem, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0221
Description:	Hard disk error. Error in /IMG_MNG.
Remedy:	This is the error which usually does not occur in Read/Write level. 1. Check the Cable and Power Connector. 2. If the measures above do not solve the problem, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0222
Description:	Hard disk error. Error in /IMG_MNG.
Remedy:	Error due to data corruption or software bug. 1. Start up in Safe Mode to perform All Format using SST and reinstall the system (SYSTEM, LANGUAGE, RUI), and then turn OFF and then ON the main power. 2. If the measures above do not solve the problem, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0223
Description:	Hard disk error. Error in /IMG_MNG.
Remedy:	Error due to data corruption or software bug. 1. Start up in Safe Mode to perform All Format using SST and reinstall the system (SYSTEM, LANGUAGE, RUI), and then turn OFF and then ON the main power. 2. If the measures above do not solve the problem, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0224
Description:	Hard disk error. Error in /IMG_MNG.
Remedy:	Error due to data corruption or software bug. 1. Start up in Safe Mode to perform All Format using SST and reinstall the system (SYSTEM, LANGUAGE, RUI), and then turn OFF and then ON the main power. 2. If the measures above do not solve the problem, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0225
Description:	Hard disk error. Error in /IMG_MNG.
Remedy:	The document data (such as Box on the HDD) can be damaged. 1. Enter the corresponding CHK-TYPE in the partition to execute HDD-CHECK (duration: several minutes to several dozen minutes); and then turn OFF and then ON the power. 2. If the measures above do not solve the problem, enter the corresponding CHK-TYPE in the partition to execute HDDCLEAR, and then turn OFF and then ON the main power. (Use SST to perform reformat/reinstallation in the case of the following: BOOTDEV, BOOTDEV2 and APL_SEND) 3. If the error still remains, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0300
Description:	Hard disk error. Error in /FSTCDEV.
Remedy:	1. Check the Cable and Power Connector. 2. If the measures above do not solve the problem, start up in Safe Mode to perform All Format using SST and reinstall the system (SYSTEM, LANGUAGE, RUI), and then turn OFF and then ON the main power. 3. If the error still remains, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0301
Description:	Hard disk error. Error in /FSTCDEV.
Remedy:	1. Check the Cable and Power Connector. 2. If the measures above do not solve the problem, start up in Safe Mode to perform All Format using SST and reinstall the system (SYSTEM, LANGUAGE, RUI), and then turn OFF and then ON the main power. 3. If the error still remains, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E602-0302
Description:	Hard disk error. Error in /FSTCDEV.
Remedy:	1. Check the Cable and Power Connector. 2. If the measures above do not solve the problem, start up in Safe Mode to perform All Format using SST and reinstall the system (SYSTEM, LANGUAGE, RUI), and then turn OFF and then ON the main power. 3. If the error still remains, it can be caused by HDD failure; therefore, replace the HDD and reinstall the system.

Error code:	E604-1024
Description:	The image memory (SDRAM) is faulty/insufficient Memory is faulty/insufficient (1024MB is required)
Remedy:	Add on the SDRAM

Error code:	E609-0008
Description:	Hard disk trouble When the HDD fails to reach the prescribed temperature within the prescribed period of time when it is started up
Remedy:	Replace with an HDD which is guaranteed to operate at low temperatures.

Error code:	E609-0009
Description:	Hard disk trouble When the HDD fails to reach the prescribed temperature when its operation is restored from the sleep mode
Remedy:	Replace with an HDD which is guaranteed to operate at low temperatures.

Error code:	E610-0001
Description:	The Encryption Board does not exist. No Encryption Board was detected.
Remedy:	1. Check that the Encryption Board is installed properly. (Perform the installation procedure) 2. Replace the Encryption Board.

Error code:	E610-0002
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Not meeting the memory configuration to execute encryption operation.
Remedy:	Check the hardware configuration.

Error code:	E610-0101
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Failed to initialize the memory of key storage area.
Remedy:	Turn OFF and then ON the power.

Error code:	E610-0102
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Failed to initialize the encryption processing part.
Remedy:	Turn OFF and then ON the power.

Error code:	E610-0201
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Error in the encryption processing part.
Remedy:	Turn OFF and then ON the power.

Error code:	E610-0202
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Error in the encryption processing part.
Remedy:	Turn OFF and then ON the power.

Error code:	E610-0301
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error).
Remedy:	Turn OFF and then ON the power.

Error code:	E610-0302
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Failure of the encryption key is detected
Remedy:	Turn OFF and then ON the power. Due to this error, HDD content is initialized.

Error code:	E610-0303
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Failure of the encryption key is detected.
Remedy:	Turn OFF and then ON the power. Due to this error, HDD content is initialized.

Error code:	E610-0401
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Error is detected during encryption.
Remedy:	Turn OFF and then ON the power.

Error code:	E610-0402
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Error is detected during decryption.
Remedy:	Turn OFF and then ON the power.

Error code:	E610-0501
Description:	Failure of the HDD encryption key (hardware configuration error/initialization error/encryption key error/encryption processing error). Error in document management information on /FSTDEV.
Remedy:	Turn OFF and then ON the power.

Error code:	E611-0000
Description:	Rebooting repeat error due to SRAM failure, etc. Rebooting error when the SRAM data has been destroyed, the job information saved in the SRAM can no longer be read or when rebooting is otherwise repeated when the power is shut off and restored
Remedy:	- Clear the SRAM. - Clear the power shutdown guaranteed jobs.

Error code:	E677-0001
Description:	DPRAM size error In communication for initialization, the DPRAM size returned by the PDL board to the host machine has an error. (The host machine is aware of the DPRAM size in advance; the DPRAM is a dual-port RAM used for communication between the host machine and the PDL board, and is mounted on the PDL board.)
Causes:	The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty.
Remedy:	1. Connector Is the printer board (accessory) connected correctly? NO: Correct the connection. 2. Printer board, Main controller PCB Try replacing the printer board. Is the problem corrected? YES: End. NO: Replace the main controller PCB.

Error code:	E677-0003
Description:	There is an external controller error. An error has been detected by a check on the configuration when the external controller is being started up.
Remedy:	Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external contro

Error code:	E677-0004
Description:	PDL board disconnection After the connection of the PDL board is recognized at power-on, the PDL board is disconnected. During power-up, monitoring is executed at intervals of 2 min; however, if the CPU is not on (sleep state or the like), no error will be identified even if the PDL board is discontented. If the PDL board is disconnected in sleep state, the absence of the PDL board will be recognized at the start of the CPU.
Causes:	The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty.
Remedy:	- Check connection of the connector for cooling CPU - Replace CPU cooling fan

Error code:	E677-0010
Description:	There is an external controller error. A controller for a non-Canon machine is connected.
Remedy:	Turn off the main power, and check the controller is an appropriate type, and check the cable; then turn on the main power. If the machine fails to reset, re-install the system software of the external controller.

Error code:	E677-0080
Description:	There is an external controller error. There is an error in the communication with the printer after the external controller has started up normally.
Causes:	The connection between the host machine and the PDL board is faulty. The system software is faulty. The hard disk is faulty. The PDL board is faulty. The system controller PCB of the host machine is faulty.
Remedy:	Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external controller.

Error code:	E710-0001
Description:	IPC initializing error When the ready status fails to be established within 3 sec. after the IPC chip started up
Causes:	The DC controller PCB is faulty. The reader controller PCB is faulty. The machine controller PCB is faulty.
Remedy:	Check the cable connections.

Error code:	E711-0001
Description:	IPC communication error When error occurrence was set 4 or more times in the error register of the IPC chip within 1.5 sec.
Causes:	The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty.
Remedy:	Check the cable connections. Replace the ADF controller PCB. Replace the reader controller PCB.

Error code:	E711-0002
Description:	There is an IPC communication error. An error has been detected 4 times or more within 1.5 sec after the communication has been interrupted between the finisher and the printer, and the machine does not reset.
Causes:	The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty.
Remedy:	Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to reset, check the connector between the finisher and the copier for poor contact; as necessary, replace the finisher controller/DC controller.

Error code:	E711-0004
Description:	IPC communication error (checksum error). Communication between the host machine and the Finisher was lost.
Remedy:	1. Check the cable connection. Check the connection between DCON side (J462) and Finisher Lattice side (J9043) Finisher Cable 2. Replace the DC Controller PCB.

Error code:	E711-0020
Description:	IPC communication error (recovery error). Communication between the host machine and the Finisher was lost.
Remedy:	1. Check the cable connection. Check the connection between DCON side (J462) and Finisher Lattice side (J9043) Finisher Cable 2. Replace the DC Controller PCB.

Error code:	E711-0040
Description:	IPC communication error (serial error). Communication between the host machine and the Finisher was lost
Remedy:	1. Check the cable connection. Check the connection between DCON side (J462) and Finisher Lattice side (J9043) Finisher Cable 2. Replace the DC Controller PCB.

Error code:	E713-0001
Description:	There is a finisher communication error. There is an error in the IC used for communication by the sorter.
Remedy:	Turn off the main power switch, and check the wiring of the DC controller PCB and the finisher controller PCB, and check the 24V system fuse: then, turn on the main power switch. If the machine does not reset, replace the DC controller PCB/finisher controller PCB.

Error code:	E713-0002
Description:	Error in IPC communication When detecting CRC error at transmission.
Remedy:	Check the connector connected to the Finisher.

Error code:	E713-0004
Description:	Finisher/printer communication error When communication between the finisher and copier was interrupted
Remedy:	Check the cable connections. Replace the finisher controller PCB. Replace the DC controller PCB.

Error code:	E713-0020
Description:	UFDI communication error BCC of the reception data is invalid for specified number of times in a row.
Remedy:	Check the connection of the Connector with Finisher.

Error code:	E713-0040
Description:	Finisher IPC communication error (serial error). Communication between the host machine and the Finisher was lost.
Remedy:	1. Check the cable connection of the Finisher. DC Controller side: J462, Finisher Lattice side: J9043 2. Replace the Finisher Controller PCB.

Error code:	E717-0001
Description:	Error in communication with NE controller When the NE controller which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Causes:	The wiring is faulty (short circuit, open circuit). The DA unit PCB is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the cable connections.

Error code:	E717-0002
Description:	Error in communication with NE controller When the IPC has a broken or disconnected wire or when an error has occurred where IPC communication cannot be recovered
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR.

Error code:	E719-0001
Description:	Error in communication with coin vendor/card reader When the coin vendor which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Causes:	The wiring is faulty (short circuit, open circuit). The Card Reader-C1 is faulty. The coin vendor is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.
Remedy:	Check the cable connections.

Error code:	E719-0002
Description:	Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.)
Causes:	Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.)
Remedy:	- Check the connection between the image processor PCB and serial PCB. - Check the connectors of the serial PCB and coin vendor for normal connection. - Replace the serial PCB. - Check the coin vendor. - Replace the image processor PCB.

Error code:	E719-0003
Description:	There is a coin vendor error. While the unit price is being checked at startup, an error occurs in the communication with the coin vendor.
Remedy:	Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR.

Error code:	E719-0011
Description:	Error in communication with coin vendor/card reader When the card reader which was connected before the power was turned OFF could not be recognized when the power was turned back ON
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR

Error code:	E719-0012
Description:	Error in communication with coin vendor/card reader When a wire in the IPC cable connected with the card reader is broken or disconnected or when an error has occurred where IPC communication cannot be recovered
Remedy:	In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR

Error code:	E719-0031
Description:	There is a coin vendor error. Error in communication at card reader (serial) startup Communication with the card reader cannot be started at startup.
Remedy:	1. Check the connection of the cable for the card reader (connector disconnected, cable cut); thereafter, reset the condition in service mode: COPIER > FUNCTION > CLEAR > ERR. 2. Execute the following items in service mode after removing the card reader, and then install the card reader again. - COPIER > FUNCTION > CLEAR > CARD - COPIER > FUNCTION > CLEAR > ERR

Error code:	E719-0032
Description:	There is a coin vendor error. Error in communication after card reader (serial) startup Communication with the card reader is available at startup, and then becomes unavailable.
Remedy:	Check the connection of the cable for the card reader (connector disconnected, cable cut); thereafter, reset the condition in service mode: COPIER > FUNCTION > CLEAR > ERR.

Error code:	E720-0001
Description:	Model mismatch error. An accessory that is not supported is connected.
Remedy:	Check the configuration of accessories. Staple Finisher-K1 is connected with iR ADV C9280.

Error code:	E720-0002
Description:	Model mismatch error. An accessory that is not supported is connected.
Remedy:	Check the configuration of accessories. Staple Finisher-K1 is connected with iR ADV C9270.

Error code:	E730-1001
Description:	There is a PDL software error. An initialization error has occurred.
Remedy:	- Execute PDL resetting. - Turn on the power once again.

Error code:	E730-100A
Description:	Printer service call

Error code:	E730-9004
Description:	There is a PDL software error. There is an error in the communication (PAI) with an external controller.
Remedy:	- Turn on the power once main. - Check the connection of the open I/F board and the cable. - Replace the board for the external controller open I/F. - Replace the main controller PCB.

Error code:	E730-9005
Description:	There is a PDL software error. Fault in the connector of the vide cable to the external controller
Remedy:	- Turn on the power once main. - Check the connection of the open I/F board and the cable. - Replace the board for the external controller open I/F. - Replace the main controller PCB.

Error code:	E730-A006
Description:	There is a PDL software error. The PDL board does not respond. A subbootable is faulty or absent.
Remedy:	- Execute PDL resetting. - Turn on the power once again. - Check the connection of the UFR board. - Re-install the firmware. - Replace the main controller PCB.

Error code:	E730-A007
Description:	There is a PDL software error. There is a mismatch between the control software of the machine and the PDL control software in regard to version.
Remedy:	- Execute PDL resetting. - Turn on the power once again. - Execute system formatting (all), and reinstall the system.

Error code:	E730-B013
Description:	There is a PDL software error. Corruption in the font data
Remedy:	- Turn on the power once again. - Re-install the Software. - Execute system formatting (all), and reinstall the system.

Error code:	E732-0000
Description:	Scanner communication error.
Causes:	Scanner communication error
Remedy:	1. Install the set of the controller firmware. 2.Replace the Main Controller PCB (UN30).

Error code:	E732-0001
Description:	Scanner communication error
Causes:	Scanner communication error
Remedy:	1. Update the firmware. 2. Replace the Main Controller PCB.

Error code:	E732-0010
Description:	There is an error in the communication with the scanner Fault in detection of DDI-S Vsync signal
Remedy:	1. Check the connector used to connect the scanner. 2. Check the power supply of the scanner (to see if initialization takes place at startup). 3. Replace the reader controller, scanner board, or main board as necessary.

Error code:	E732-9999
Description:	There is an error in reader communication. Although a printer model, the machine is identified as a reader unit at start-up. (A copier model is started up as a printer model when the RAM is initialized.)
Remedy:	Turn off and then on the main power.

Error code:	E733-0000
Description:	Erroneous communication between controller and printer Cannot communicate with the printer at startup.
Causes:	Printer communication error (communication error at initial communication and negotiation packet error)
Remedy:	- Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB.

Error code:	E733-0001
Description:	Printer communication error (Invalid communication after communication is established, Parity error)
Remedy:	Turn on the power again. Replace the DC controller PCB.

Error code:	E733-0002
Description:	Printer communication error. An error occurred to detect printer vertical synchronous signal.
Remedy:	1. Check the connection to the printer. ?¨ Connect the connector/replace the harness. 2. Check the power of the printer (check if the initialization operation is executed at startup). 3. Replace the DC Controller PCB/Main Controller PCB.

Error code:	E733-0010
Description:	There is an error in the communication with the printer Fault in detection of DDI-P Vsync signal
Remedy:	1. Check the connection with the printer. 2. Check the power supply of the printer (to see if initialization takes place at startup). 3. Replace the DC controller or the main board.

Error code:	E740-0002
Description:	Error detection on either Network Board or Mac address
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board.

Error code:	E743-0000
Description:	Error in main controller communication An error in reading of/writing to the Flash ROM in the Main Controller occurred.
Causes:	Software sequence error
Remedy:	1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB.

Error code:	E743-0003
Description:	DDI communication error. The reader controller PCB detected a failure in communication between the main controller PCB and the reader controller PCB.
Remedy:	1. Failure of the connection between the main controller PCB and the reader controller PCB 2. Failure of the reader controller PCB (PCB1) 3. Failure of the main controller PCB

Error code:	E743-0004
Description:	DDI communication error. The reader controller PCB detected a failure in communication between the main controller PCB and the reader controller PCB.
Remedy:	1. Failure of the connection between the main controller PCB and the reader controller PCB 2. Failure of the reader controller PCB (PCB1) 3. Failure of the main controller PCB

Error code:	E744-0001
Description:	Language file/boot ROM/USB memory error The language file version does not match Bootable.
Causes:	Language file version error The language file version does not match Bootable.
Remedy:	Download a language file of the correct version.

Error code:	E744-0002
Description:	Language file/boot ROM/USB memory error The language file is longer than the permitted size.
Causes:	Language file size error The language file is longer than the permitted size.
Remedy:	Download a language file of the correct version.

Error code:	E744-0003
Description:	Language file/boot ROM/USB memory error The language file version does not match Bootable
Causes:	Language file version error The language file version does not match Bootable.

Error code:	E744-0004
Description:	Language file/boot ROM/USB memory error Language file read error
Causes:	Language file read error Reading of language file is invalid.
Remedy:	Download a language file of the correct version.

Error code:	E744-1000
Description:	Mismatch of the series or model of the firmware sent at the time of downloading
Remedy:	Check the supported series or model of the firmware, and burn the correct series or model of firmware.

Error code:	E744-2000
Description:	There is an error in the language file/boot ROM. The engine ID indicated by the software ID is illegal.
Remedy:	Replace it with a software ID of the correct model.

Error code:	E744-4000
Description:	Engine ID error (Invalid engine connection is detected)
Causes:	Error in engine ID Detected illegal engine connection
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the DC Controller Board. (2) Update the Engine Firmware. (3) Update the set of the Controller Firmware

Error code:	E746-0003
Description:	The accessories board is of the wrong type. At time of start-up, the UFR board is found to be of the wrong type. (A query is made to find out if the type is correct with reference to the engine ID.)
Remedy:	Replace it with a UFR board of the correct type.

Error code:	E746-0021
Description:	Image analysis board self-check failure detection.
Remedy:	1. Connection check of the image analysis board 2. Image analysis board replacement

Error code:	E746-0022
Description:	Image analysis board version is invalid.
Remedy:	1. Upgrading of the image analysis board software 2. Image analysis board replacement

Error code:	E746-0023
Description:	No response from image analysis board.
Remedy:	1. Connection check of the image analysis board 2. Image analysis board replacement

Error code:	E746-0024
Description:	Image analysis board operation abnormality
Remedy:	1. Connection check of the image analysis board 2. Image analysis board replacement

Error code:	E746-0031
Description:	Hardware error (TPM)
Remedy:	1. TPM board non-installation 2. Installation of TPM board from other units 3. TPM chip broken

Error code:	E746-0032
Description:	The error that system restoration is impossible occurred (TPM)
Remedy:	The location of the security information in HDD/SRAM is unidentified Execute “Initialization of all data / setting”

Error code:	E746-0033
Description:	Error occurred; but possible for system restoration (TPM)
Remedy:	Discrepancy of the key Execute the re-store of the TPM key

Error code:	E746-0034
Description:	Error occurred; but possible for automatic system restoration (TPM)
Remedy:	Discrepancy of the key occurred. But restoration is possible when reboot. Power cycle (Power OFF/ON)

Error code:	E748-2000
Description:	There is a mismatch between controller board and SDRAM size. An error occurs when accessing the chip on the main controller PCB.
Remedy:	Replace the main controller PCB.

Error code:	E748-2001
Description:	There is a mismatch between controller board and SDRAM size. An error occurs when accessing the memory on the main controller PCB.
Remedy:	1. Unplug/plug in the memory. 2. Replace the main controller PCB.

Error code:	E748-4910
Description:	There is a mismatch between controller board and SDRAM size. A controller board that does not match the product is defected.
Remedy:	- Replace the main controller PCB.

Error code:	E748-9000
Description:	System error
Remedy:	Contact each sale company bases

Error code:	E753-0001
Description:	Error in Finisher Boot software. The Boot software has not been written in ROM of the finisher controller.
Remedy:	1. The finisher controller PCB is faulty. 2. The host machine controller PCB is faulty.

Error code:	E804-0000
Description:	Power supply fan failure

Error code:	E804-0001
Description:	Controller fan error Stop of power supply cooling fan 2 was detected
Remedy:	Check the connection of power supply cooling fan 2, replace it

Error code:	E806-0000
Description:	Fan Motor cannot rotate at specified revolution speed.
Causes:	Fixing / fixing power supply cooling fan does not rotate in the specified rotation speed. Cause: Problem in fixing / fixing power supply cooling fan / DC controller PCB
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Main Fan Unit. (2) Replace the DC Controller Board.

Error code:	E808-0001
Description:	Fixing Assembly_Edge Left Cooling Fan error
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Edge Left Cooling Fan. (2) Replace the DC Controller Board.

Error code:	E808-0002
Description:	Fixing Assembly_Edge Right Cooling Fan error
Causes:	Error in the Edge Right Cooling Fan (FAN2) of the Fixing Assembly
Remedy:	When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Edge Right Cooling Fan. (2) Replace the DC Controller Board.

Error code:	E808-0003
Description:	Fixing Power Supply error. Inlet current is 1A or lower for 1 second or longer although the maximum voltage is output.
Remedy:	1. Check the clogging of the Fixing Power Supply Cooling Fan (FM7). 2. Check the clogging of the Louver on right side of the host machine (Multi-purpose Tray side). 3. Check the connection of the Fixing Power Supply PCB (PCB10) Output Connector. 4. Replace the Fixing Power Supply PCB (PCB10).

Error code:	E808-0004
Description:	Fixing Power Supply error. Detected OFF with 12V of the Main Driver PCB (PCB2) output.
Remedy:	Replace the Main Driver PCB (PCB2).

Error code:	E808-0005
Description:	12V OFF detection when relay is turned ON. Detected OFF with 12V of the Fixing Power Supply output after IH relay is turned ON.
Remedy:	1. Check the conduction of the Fixing Thermal Switch 1/2 (TP1/2). 2. Check the drawer between the Fixing Assembly and the host machine. 3. Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10). 4. Replace the Fixing Power Supply Unit. 5. Replace the Main Driver PCB (PCB2).

Error code:	E808-0006
Description:	ASIC error.
Remedy:	Replace the DC Controller PCB (PCB1).

Error code:	E808-0007
Description:	Fixing Power Supply error. Inlet voltage and the IH Power Supply ID are not matched.
Remedy:	Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10). Replace the Fixing Power Supply PCB with the one for the correct location (voltage).

Error code:	E808-0008
Description:	Fixing Power Supply error. Current fluctuation error.
Remedy:	1. Check the connection between the Main Driver PCB (PCB2) and the Fixing Power Supply PCB (PCB10). 2. Check the connection between the Fixing Power Supply PCB (PCB10) and the Heater Unit. 3. Replace the Fixing Assembly (Fixing Roller and Heater Unit). 4. Replace the Fixing Power Supply PCB (PCB10). 5. Replace the Main Driver PCB (PCB2).

Error code:	E808-0009
Description:	Fixing Power Supply error. Unable to clear the error flag at power-on.
Remedy:	Replace the DC Controller PCB (PCB1).

Error code:	E820-0000
Description:	The rotation of the drum fan is faulty. The lock signal is detected for 5 sec or more although the drum fan is being driven.
Remedy:	- Check if there is no foreign material in the rotation assembly of the drum fan. - Check if the connector (J512) of the DC controller PCB is mounted properly. - Replace the drum fan. - Replace the DC controller PCB.

Error code:	E820-0001
Description:	Developing Cooling Fan (Front) (FM7) rotation error The lock signal was not detected for 5.0 seconds while the Developing Cooling Fan (Front) (FM7) was being driven. *The same status was detected again after executing an error retry.
Remedy:	1. Check the connector connection between the Developing Cooling Fan (Front) (FM7) and the DC Controller PCB (PCB1). 2. Replace the Developing Cooling Fan (Front) (FM7). 3. Replace the DC Controller PCB (PCB1).

Error code:	E820-0002
Description:	There is an error in the process unit cooling fan. There is an error in the process unit fan.
Remedy:	Turn off the main switch, and check the wiring of the DC controller PCB and the 24V system fuse; then, turn on the main switch.

Error code:	E824-0000
Description:	There is an error in the primary charging suction/primary charging exhaust fan. There is an error in the primary charging suction mechanism.
Remedy:	Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main switch.

Error code:	E840-0001
Description:	Fixing Core/Shield Plate HP error. At the Fixing Core/Shield Plate home position detection operation, move from inside the home position range to outside the range is not completed after the specified period of time has passed.
Remedy:	1. Check the connection of connectors of the Core Shutter Motor (M56) and Core HP Sensor (PS98). 2. Check the harness of the target parts. -> Replace the harness if it is disconnected. 3. Replace the Core Shutter Motor (M56) and Core HP Sensor (PS98). 4. Clean the IH Unit. (Refer to the Service Manual.) 5. Replace the IH Unit. 6. Replace the Fixing Feed Driver PCB (UN5).

Error code:	E880-0001
Description:	Controller fan1 (FM19) Error. When detect a failure of the power supply cooling fan
Remedy:	1. Connector disconnection 2. Controller fan 1 (FM19) failure

Error code:	E880-0005
Description:	HDD cooling fan (FM21) error. When detect a failure of the power supply cooling fan
Remedy:	1. Connector disconnection 2. HDD cooling fan (FM21) failure

Error code:	E905-0001
Description:	POD deck light air assist fan error. Even when the maximum LOW interval was passed, there was no change in the signal.
Remedy:	1. Failure of the shutter 2. Failure of the swing sensor (PS11) 3. Failure of the swing motor (M3) 4. Failure of the deck controller PCB (UN1)

Error code:	E905-0002
Description:	POD deck pickup motor cooling fan error. The pickup motor cooling fan is not placed at LOCK ON status.
Remedy:	1. Check the connector of the pickup motor cooling fan (FM4). 2. Replace the pickup motor cooling fan. 3. Replace the deck controller PCB.

Error code:	E905-0003
Description:	POD deck pickup motor cooling fan error. The pickup motor cooling fan is not placed at LOCK OFF status.
Remedy:	1. Check the connector of the pickup motor cooling fan (FM4). 2. Replace the pickup motor cooling fan. 3. Replace the deck controller PCB.

Error code:	E906-0001
Description:	POD deck light air heater high temperature error. A temperature over 120 degreeC was detected for 1 second consecutively.
Remedy:	1. Failure of the environment sensor (SR1) 2. Failure of the warm air fan (FAN1) 3. Failure of the cool air fan (FAN2) 4. Failure of the additional fan (FAN3) 5. Failure of the air heater (H1) 6. Failure of the deck controller PCB (UN1)

Error code:	E906-0002
Description:	POD deck light air heater low temperature error. The heater is not placed in the Ready status even when a specified period of time has elapsed.
Remedy:	1. Failure of the environment sensor (SR1) 2. Failure of the warm air fan (FAN1) 3. Failure of the cool air fan (FAN2) 4. Failure of the additional fan (FAN3) 5. Failure of the air heater (H1) 6. Failure of the deck controller PCB (UN1)

Error code:	E996-xxxx
Description:	Timeout error. The DC Controller is not stopped. The Detailed Code varies according to the state transition of the software
Remedy:	Turn OFF and then ON the main power.

Canon imageRUNNER Advance 8295 PRO

Общие характеристики

Макс. формат

Цветность печати

Тип

Технология печати

Размещение

Копир

Сканер

Тип устройства

Печать фотографий

Телефон

Факс

Принтер

Время разогрева

Прямая печать

Двусторонняя печать

Пигментные чернила

Печать без полей

Макс, разрешение для ч/б печати

Скорость ч/б печати

Копир

Макс, количество копий за цикл

Время выхода первой копии

Значение масштаба

Макс, разрешение (ч/б)

Сканер

Макс. формат оригинала

Емкость устройства автоподачи оригиналов

Тип сканера

Оттенки серого

Стандарт TWAIN

Отправка изображения по e-mail

Стандарт WIA

Слайд-адаптер

Устройство автоподачи оригиналов

Макс, размер сканирования

Разрешение сканера

Скорость сканирования

Расходные материалы

Количество картриджей

Ресурс ч/б картриджа/тонера

Печать на:

Плотность бумаги

Факс

PC Fax

Цветной

Телефон

Caller ID

Спикерфон

Автоответчик

Беспроводная трубка

АОН

Стандарт DECT

Проводная трубка

Шрифты и языки управления

Языки управления

Количество установленных шрифтов

Лотки

Емкость лотка ручной подачи

Подача бумаги

Вывод бумаги

Финишер

Сортировка со сдвигом

Брошюровщик

Степлер

Сортер

Электронная сортировка

Интерфейсы

Версия USB

Ethernet (RJ-45)

Веб-интерфейс

USB

Bluetooth

LPT

AirPrint

Инфракрасный порт

RS-232

Устройство для чтения карт памяти

FireWire (IEEE 1394)