Canon imageRUNNER Advance C2220i
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Скорость печати
A4
20
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Цветность печати |
цветная |
Телефон |
|
Факс |
|
Печать фотографий |
|
Размещение |
напольный |
Макс. формат |
A3 |
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Тип устройства |
МФУ |
Копир |
|
Сканер |
|
Принтер |
|
Время разогрева |
34 |
Прямая печать |
|
Двусторонняя печать |
|
Печать без полей |
|
Пигментные чернила |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
| По X | 1 200 |
| По Y | 1 200 |
Скорость ч/б печати |
|
| A4 | 20 |
Копир |
|
Время выхода первой копии |
5,9 |
Макс, количество копий за цикл |
999 |
Шаг масштабирования |
0,01 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По Y | 600 |
| По Y | 1 200 |
| По X | 1 200 |
Скорость ч/б копирования |
|
| A3 | 15 |
Сканер |
|
Тип сканера |
планшетный/протяжный |
Стандарт TWAIN |
|
Стандарт WIA |
|
Отправка изображения по e-mail |
|
Устройство автоподачи оригиналов |
двустороннее |
Макс. формат оригинала |
A3 |
Слайд-адаптер |
|
Разрешение сканера |
|
| По Х | 600 |
Расходные материалы |
|
Количество картриджей |
4 |
Ресурс ч/б картриджа/тонера |
23 000 |
Ресурс цветного картриджа/тонера |
19 000 |
Печать на: |
|
| CD/DVD |
|
| Фотобумаге |
|
| Рулоне |
|
| Конвертах |
|
| Глянцевой бумаге |
|
| Карточках |
|
| Пленках |
|
| Матовой бумаге |
|
| Этикетках |
|
Плотность бумаги |
|
| Минимальная | 64 |
| Максимальная | 220 |
Факс |
|
Цветной |
|
Телефон |
|
Беспроводная трубка |
|
Стандарт DECT |
|
Автоответчик |
|
Caller ID |
|
АОН |
|
Спикерфон |
|
Проводная трубка |
|
Шрифты и языки управления |
|
Языки управления |
|
| PostScript 2 |
|
| PPDS |
|
| PostScript 3 |
|
| PostScript | опционально |
| PCL 5e |
|
| PCL 6 |
|
Количество установленных шрифтов |
|
| PCL | 105 |
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Максимальная | 2 270 |
| Стандартная | 1 170 |
Вывод бумаги |
|
| Максимальный | 3 000 |
| Стандартный | 250 |
Финишер |
|
Степлер |
|
Сортер |
|
Брошюровщик |
|
Интерфейсы |
|
Версия USB |
2,0 |
LPT |
|
Инфракрасный порт |
|
RS-232 |
|
Wi-Fi |
|
FireWire (IEEE 1394) |
|
Bluetooth |
|
USB |
|
Ethernet (RJ-45) |
|
Память/Процессор |
|
Емкость жесткого диска |
160 |
Объем памяти |
6 144 |
Частота процессора |
1 670 |
Дополнительная информация |
|
Диагональ дисплея |
7 |
Работа от аккумулятора |
|
Экран |
|
Поддержка ОС |
|
| DOS |
|
| Mac OS |
|
| Windows |
|
Потребляемая мощность |
|
| В режиме ожидания | 75 |
| При работе | 940 |
Уровень шума |
|
| При работе | 48 |
| В режиме ожидания | 25 |
Габариты |
|
Высота |
1 117 |
Глубина |
680 |
Ширина |
565 |
Вес |
120 |
Модули
352 2ND/3RD DELIVERY GUIDE ASSY (2/3 DELIVERY MODEL)
530 INTER. TRANSFER BELT ASSY
102 INTERNAL COMPONENTS 1
B10 ADF MAIN BODY (ADF MODEL)
301 CASSETTE ASSEMBLY (LOWER) (EXCEPT 1 CASSETTE MODEL)
460 LASER SCANNER UNIT
260A LIFTER DRIVE ASSEMBLY (1 CASSETTE model)
250 MAIN DRIVE ASSEMBLY
B41 FEED ASSEMBLY (ADF model) 2
110 MACHINE REAR PLATE 2
B13 DOCUMENT TRAY ASSY (ADF model)
350 2ND/3RD PAPER DELIVERY ASSY (2/3 DELIVERY MODEL)
103 INTERNAL COMPONENTS 2
310 PAPER PICK-UP ASSEMBLY (UPPER) (EXCEPT 1 CASSETTE model)
930 MAIN CONTROLLER PCB ASSY, 1
311 PAPER PICK-UP ASSEMBLY (LOWER) (EXCEPT 1 CASSETTE MODEL)
106 INTERNAL COMPONENTS 5
101 RIGHT DOOR ASSEMBLY 2
100 EXTERNAL COVERS, PANELS, ETC. 2
B12 PAPER PICK-UP COVER ASSY (ADF model)
300A CASSETTE ASSEMBLY (UPPER) (1 CASSETTE model)
351 2ND/3RD DRIVE FRAME ASSEMBLY (2/3 DELIVERY MODEL)
D11 READER ASSEMBLY (ADF,READER model)
310A PAPER PICK-UP ASSY (UPPER) (1 CASSETTE model)
105 INTERNAL COMPONENTS 4
109 MACHINE REAR PLATE 1
B21 ESTRANGEMENT DRIVE ASSEMBLY (ADF MODEL)
980 HIGH VOLTAGE PCB ASSEMBLY
130 CONTROL PANEL ASSEMBLY
960 AC DRIVER PCB ASSEMBLY
B11 BASE ASSEMBLY (ADF MODEL)
104 INTERNAL COMPONENTS 3
900 CONTROLLER BOX ASSEMBLY
100 EXTERNAL COVERS, PANELS, ETC.
140 POWER CORD TERMINAL ASSY
931 MAIN CONTROLLER PCB ASSY, 2
108 INTERNAL COMPONENTS 7
280 FIXING DRIVE ASSY
352 2ND/3RD DELIVERY GUIDE ASSY (2/3 DELIVERY MODEL) 2
265 PAPER PICK-UP DRIVE ASSEMBLY (EXCEPT 1 CASSETTE model)
B01 ADF MOUNTING ASSEMBLY (ADF model)
101 RIGHT DOOR ASSEMBLY
300 CASSETTE ASSEMBLY (UPPER) (EXCEPT 1 CASSETTE model)
810 FIXING ASSEMBLY
B41 FEED ASSEMBLY (ADF model)
B90 ADF PCB ASSEMBLY (ADF MODEL)
107 INTERNAL COMPONENTS 6
260 LIFTER DRIVE ASSEMBLY (EXCEPT 1 CASSETTE model)
Детали 107 INTERNAL COMPONENTS 6
| Деталь: | FLAG, 2ND DELIVERY SENSOR |
| Парткод: | FC5-0996-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-0997-000 |
| Деталь: | FLAG, DUPLEX ENTRANCE SENSOR |
| Парткод: | FC5-1005-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-1006-000 |
| Деталь: | FLAG, 3RD DELIVERY SENSOR |
| Парткод: | FC5-1010-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC0-0636-000 |
| Деталь: | GUIDE, 3RD DELIVERY |
| Парткод: | FC8-8293-000 |
| Деталь: | HANDLE, PAPER DELIVERY DOOR |
| Парткод: | FC8-8297-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-8298-000 |
| Деталь: | GUIDE, DUPLEX ENTRANCE, 1 |
| Парткод: | FC8-8300-000 |
| Деталь: | GUIDE, 3RD DELIVERY, UPPER |
| Парткод: | FC8-8301-000 |
| Деталь: | GUIDE, REVERSE ENTRANCE |
| Парткод: | FC8-8304-000 |
| Деталь: | GUIDE, DUPLEX ENTRANCE, 2 |
| Парткод: | FC8-8309-000 |
| Деталь: | ROLLER, 2ND PAPER DELIVERY |
| Парткод: | FC8-8311-000 |
| Деталь: | COVER, 2ND DELIVERY GEAR |
| Парткод: | FC8-8331-000 |
| Деталь: | COVER, 3RD DELIVERY GEAR |
| Парткод: | FC8-8332-000 |
| Деталь: | SUPPORT, 2ND DELIVERY GEAR |
| Парткод: | FC8-8338-000 |
| Деталь: | SUPPORT, 3RD DELIVERY GEAR |
| Парткод: | FC8-8339-000 |
| Деталь: | GUIDE, ENTRANCE, 2 |
| Парткод: | FC8-8340-010 |
| Деталь: | GUIDE, SHAFT |
| Парткод: | FC8-8408-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-8410-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-8411-000 |
| Деталь: | COVER, 3RD DELIVERY ROLLER |
| Парткод: | FC8-8503-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC8-8591-000 |
| Деталь: | SHEET, PAPER DELIVERY |
| Парткод: | FC9-8580-000 |
| Деталь: | GUIDE, ENTRANCE, 1 |
| Парткод: | FL3-0641-000 |
| Деталь: | PAPER DELIVERY ROLLER ASSEMBLY |
| Парткод: | FM3-8053-000 |
| Деталь: | 3RD DELIVERY FLAPPER ASSY |
| Парткод: | FM3-8054-000 |
| Деталь: | 2ND FLAPPER SOLENOID ASSY |
| Парткод: | FM3-8056-000 |
| Деталь: | 3RD FLAPPER SOLENOID ASSY |
| Парткод: | FM3-8057-000 |
| Деталь: | ROLLER, REFORM |
| Парткод: | FC9-8621-000 |
| Деталь: | ROLLER, 3RD PAPER DELIVERY |
| Парткод: | FC8-8294-000 |
| Деталь: | 2ND UPPER GUIDE ASSEMBLY |
| Парткод: | FM3-8060-000 |
| Деталь: | PAPER DELIVERY FLAPPER ASSY |
| Парткод: | FM3-8062-000 |
| Деталь: | TOGGLE COVER ASSEMBLY |
| Парткод: | FM3-8063-000 |
| Деталь: | COLLAR, REGISTRATION MULTI |
| Парткод: | FS5-6945-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FS7-2859-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1453-000 |
| Деталь: | BUSHING, POLYACETAR |
| Парткод: | FU5-1469-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU6-0076-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2772-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2783-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0396-000 |
| Деталь: | GEAR, 20T |
| Парткод: | FU8-0397-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0403-000 |
| Деталь: | ROLLER, DUPLEXING PAPER FEED |
| Парткод: | RC2-7271-000 |
| Деталь: | BUSHING |
| Парткод: | RS5-1567-000 |
| Деталь: | GEAR, 28T |
| Парткод: | RU6-0852-000 |
| Деталь: | GEAR, 17T |
| Парткод: | RU6-0855-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | IC,PHOTO-INTERRUPTER,LG248NL1A |
| Парткод: | WG8-5783-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FC9-8582-000 |
| Деталь: | SHEET, ENTRANCE GUIDE, 1 |
| Парткод: | FC8-8310-000 |
| Деталь: | GUIDE, 2ND DELIVERY ENTRANCE |
| Парткод: | FC0-0598-010 |
| Деталь: | STOPPER, GUIDE, UPPER |
| Парткод: | FC9-8645-000 |
| Деталь: | STOPPER, GUIDE, LOWER |
| Парткод: | FC9-8646-000 |
| Деталь: | SHEET, COMPENSATION, F |
| Парткод: | FL3-0777-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC8-8590-010 |
| Деталь: | SHEET, COMPENSATION, R |
| Парткод: | FL3-0778-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0239-000 |
| Деталь: | 2ND/3RD DELIVERY GUIDE ASSY |
| Парткод: | FM3-8052-010 |
| Деталь: | INTER. TRANSFER BELT ASSY |
| Парткод: | FM3-8240-000 |
| Деталь: | FILTER, AIR |
| Парткод: | FC6-4023-000 |
| Деталь: | COVER, INNER, RIGHT |
| Парткод: | FC8-8199-000 |
| Деталь: | HOLDER, ENVIRONMENT SENSOR |
| Парткод: | FC8-8274-000 |
| Деталь: | ARM, COVER |
| Парткод: | FC8-8342-000 |
| Деталь: | COVER, INNER, LEFT |
| Парткод: | FC8-8343-000 |
| Деталь: | LINK, DOOR, FRONT |
| Парткод: | FC8-8364-000 |
| Деталь: | HOLDER, LINK |
| Парткод: | FC8-8365-000 |
| Деталь: | HOLDER, INTERLOCK SWITCH |
| Парткод: | FC8-8464-000 |
| Деталь: | ARM, COVER |
| Парткод: | FC8-8626-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-8627-000 |
| Деталь: | SHAFT |
| Парткод: | FC8-8636-000 |
| Деталь: | HOLDER, SWITCH |
| Парткод: | FE2-0333-000 |
| Деталь: | SHEET, CROSSMEMBER,RIGHT UPPER |
| Парткод: | FE2-1825-000 |
| Деталь: | LEVER, INTERLOCK |
| Парткод: | FE2-2084-000 |
| Деталь: | LEVER, TOGGLE |
| Парткод: | FE2-2086-000 |
| Деталь: | FAN |
| Парткод: | FK2-0360-000 |
| Цена: | 1 600 ₽ |
| Деталь: | FAN |
| Парткод: | FK2-2064-000 |
| Деталь: | SWITCH, MAIN POWER SUPPLY |
| Парткод: | FK3-2835-000 |
| Деталь: | CABLE, UI |
| Парткод: | FK3-3134-000 |
| Деталь: | LABEL, SERVICE |
| Парткод: | FL3-7841-000 |
| Деталь: | CABLE, PROCESSOR INTERFACE |
| Парткод: | FM3-8635-000 |
| Деталь: | SWITCH CABLE UNIT, INTERLOCK |
| Парткод: | FM4-1895-000 |
| Деталь: | CABLE, FRONT DOOR DETECT |
| Парткод: | FM4-1903-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2773-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2778-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2810-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2811-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2817-000 |
| Деталь: | ENVIRONMENT SENSOR PCB ASSY |
| Парткод: | RK2-2884-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WGS-5696-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | VVES-6449-000 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | SPONGE, SHEET, WHITE |
| Парткод: | FC0-9274-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FU7-8223-000 |
| Деталь: | COVER, WINDOW, REAR |
| Парткод: | FC0-9113-000 |
| Деталь: | COVER, STAMP |
| Парткод: | FC8-6311-000 |
| Деталь: | LEVER, READ 1 ESTRANGEMENT |
| Парткод: | FC8-6330-000 |
| Деталь: | HOLDER, TRAY SUPPORT |
| Парткод: | FC8-6387-000 |
| Деталь: | HOLDER, FEEDER SHAFT |
| Парткод: | FC8-6388-000 |
| Деталь: | SHEET, READ 2 LEAD |
| Парткод: | FC8-6405-000 |
| Деталь: | HINGE, LEFT |
| Парткод: | FE2-1598-000 |
| Деталь: | CABLE, CONNECTING |
| Парткод: | FM0-1193-000 |
| Деталь: | FAN |
| Парткод: | FK3-2685-000 |
| Деталь: | PANEL, COPYBOARD |
| Парткод: | FL3-7538-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FL0-0594-000 |
| Деталь: | COVER, REAR |
| Парткод: | FL3-7546-000 |
| Деталь: | RIGHT HINGE ASSEMBLY |
| Парткод: | FM3-6893-000 |
| Деталь: | CUSHION |
| Парткод: | FL3-8435-000 |
| Деталь: | CABLE, I/F |
| Парткод: | FM0-1190-000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FU7-8140-000 |
| Деталь: | LABEL, PROHIBITION DOCUMENT |
| Парткод: | FU7-8137-000 |
| Деталь: | SCREW,RS,M4 |
| Парткод: | XA9-0732-010 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FC0-9122-010 |
| Деталь: | CUSHION |
| Парткод: | FL3-7549-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-008 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | ADF MAIN BODY |
| Парткод: | NPN |
| Деталь: | DIAL, DETECT, SMALL |
| Парткод: | FC8-2469-000 |
| Деталь: | DIAL, DETECT, LARGE |
| Парткод: | FC8-2470-000 |
| Деталь: | SHAFT, SUPPORT |
| Парткод: | FC8-2474-000 |
| Деталь: | PLATE, JOINT |
| Парткод: | FC8-2475-000 |
| Деталь: | PLATE, FREE STOP |
| Парткод: | FC8-2670-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-2671-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-2672-000 |
| Деталь: | LABEL, SIZE INDEX, SIDE, LARGE |
| Парткод: | FC8-4962-000 |
| Деталь: | COLLAR, REGISTRATION MULTI |
| Парткод: | FS5-6945-000 |
| Деталь: | LABEL, PAPER PICK-UP OPERATION |
| Парткод: | FC8-4966-000 |
| Деталь: | WINDOW, CST FR. COVER IND. |
| Парткод: | FC8-4967-000 |
| Деталь: | ROLLER, CASSETTE SWING |
| Парткод: | FC8-4970-000 |
| Деталь: | BUTTON, PUSHING |
| Парткод: | FC8-4985-000 |
| Деталь: | PIN, SIZE DETECT POSITIONING |
| Парткод: | FC8-4989-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FC8-4990-000 |
| Деталь: | WIRE,CENTER PLATE GROUNDING,L |
| Парткод: | FC8-4992-000 |
| Деталь: | PLATE, COVER ATTACHMENT, LEFT |
| Парткод: | FC8-4993-000 |
| Деталь: | COVER, TOP |
| Парткод: | FC8-4996-000 |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-2007-000 |
| Деталь: | COVER, CASSETTE FRONT |
| Парткод: | FC8-8181-010 |
| Деталь: | RING, BUTTON |
| Парткод: | FC8-8182-000 |
| Деталь: | GEAR, 9T |
| Парткод: | FC9-0129-000 |
| Деталь: | LINK, BACK END DETECT |
| Парткод: | FC9-0130-000 |
| Деталь: | PAPER SIDE END EXTENSION ASSY |
| Парткод: | FM3-8912-000 |
| Деталь: | HOLDER, SIZE INDEX |
| Парткод: | FC9-0136-000 |
| Деталь: | COVER, SIZEPLATE |
| Парткод: | FC9-4042-000 |
| Деталь: | BACK END LIMIT PLATE ASSEMBLY |
| Парткод: | FM3-8907-000 |
| Деталь: | PLATE, CENTER |
| Парткод: | FL2-9472-000 |
| Деталь: | BUTTON LINK ASSEMBLY |
| Парткод: | FM3-8913-000 |
| Деталь: | PLATE, LIFTER |
| Парткод: | FL3-2859-000 |
| Деталь: | SIDE END PLATE ASSEMBLY, FRONT |
| Парткод: | FM3-8905-0 10 |
| Деталь: | SIDE END PLATE ASSEMBLY, REAR |
| Парткод: | FM3-8906-0 10 |
| Деталь: | CASSETTE ASSEMBLY |
| Парткод: | FM3-8153-000 |
| Деталь: | LASER SCANNER UNIT |
| Парткод: | FM3-8074-000 |
| Деталь: | LIFTER MOTOR UNIT |
| Парткод: | FM4-1915-000 |
| Деталь: | SIZE DETECT SWITCH UNIT |
| Парткод: | RM1-5058-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-004 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-017 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | LIFTER DRIVE ASSEMBLY |
| Парткод: | FM3-8034-000 |
| Деталь: | MAIN DRIVE MOTOR UNIT |
| Парткод: | FM3-8145-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-3298-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1833-000 |
| Деталь: | MAIN DRIVE ASSEMBLY |
| Парткод: | FM0-4719-000 |
| Деталь: | FLANGE, BELT |
| Парткод: | FC5-4353-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | GUIDE, PLATEN, 2 |
| Парткод: | FE2-1916-000 |
| Деталь: | FLAPPER, REVERSE |
| Парткод: | FL2-9949-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FC8-6372-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FC8-6377-000 |
| Деталь: | DUCT, HARNESS |
| Парткод: | FC8-6378-020 |
| Деталь: | FLANGE, PULLEY |
| Парткод: | FC8-6379-000 |
| Деталь: | CLIP |
| Парткод: | FC8-6380-000 |
| Деталь: | ROLLER, BELT TENSION |
| Парткод: | FC8-6382-000 |
| Деталь: | JOINT, DELIVERY GEAR |
| Парткод: | FC8-6385-000 |
| Деталь: | DIAL, JAM |
| Парткод: | FC0-9097-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6395-010 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FC8-6396-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FC0-4619-000 |
| Деталь: | JOINT, READ PULLEY |
| Парткод: | FC8-6418-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FC8-6421-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK3-1613-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK3-2679-000 |
| Деталь: | FLAG, REGISTRATION SENSOR |
| Парткод: | FL2-9937-000 |
| Деталь: | GEAR, 48T/62T |
| Парткод: | FU9-0937-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6411-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU9-0931-000 |
| Деталь: | JOINT, REGISTRATION |
| Парткод: | FC8-6384-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6412-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0932-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE2-1917-000 |
| Деталь: | ARM, PLATEN, FRONT |
| Парткод: | FC8-6373-000 |
| Деталь: | ARM, PLATEN, REAR |
| Парткод: | FE2-1918-000 |
| Деталь: | SPACER, READ, FRONT |
| Парткод: | FC8-6375-000 |
| Деталь: | SPACER, READ, REAR |
| Парткод: | FC8-6376-000 |
| Деталь: | ROLLER, WHITE |
| Парткод: | FC0-9124-000 |
| Деталь: | GUIDE, PLATEN, 1 |
| Парткод: | FL2-9939-000 |
| Деталь: | LINK, SOLENOID |
| Парткод: | FC8-6381-000 |
| Деталь: | DAMPER, REV. GUIDE RETAINING |
| Парткод: | FC8-6403-000 |
| Деталь: | SOLENOID |
| Парткод: | FK3-2682-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU9-0933-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | GUIDE, SEPARATION REVERSE |
| Парткод: | FM0-1223-000 |
| Деталь: | PAD, SEPARATION |
| Парткод: | FL3-5538-010 |
| Цена: | 1 400 ₽ |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2657-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1607-640 |
| Деталь: | BEARING, BALL |
| Парткод: | XG9-0820-000 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-0702-000 |
| Деталь: | SCREW,RS,M3X6.5 |
| Парткод: | XA9-1164-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1626-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1088-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1089-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2659-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2660-000 |
| Деталь: | PULLEY, 27T/GEAR, 22T |
| Парткод: | FU9-0934-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0935-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU9-0936-000 |
| Деталь: | GEAR PULLEY, 36T/54T/28T |
| Парткод: | FU8-0309-000 |
| Деталь: | PULLEY, 36T |
| Парткод: | FU8-0310-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0312-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0313-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU8-0314-000 |
| Деталь: | GEAR, 39T |
| Парткод: | FU8-0315-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU8-0316-000 |
| Деталь: | GEAR, 32T |
| Парткод: | FU8-0317-000 |
| Деталь: | SHEET, CLEANING |
| Парткод: | FC8-6356-000 |
| Деталь: | SHEET, CLEANING, SMALL |
| Парткод: | FC8-6357-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE2-1919-000 |
| Деталь: | BUSHING |
| Парткод: | FS6-1140-000 |
| Деталь: | BUSHING, CONDUCTIVE |
| Парткод: | RS5-1101-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-122 |
| Деталь: | FEED ASSEMBLY |
| Парткод: | FM0-1220-000 |
| Деталь: | COVER, HIGH VOLTAGE |
| Парткод: | FC0-0599-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SEAL, TONER SUPPORTER GUIDE, 1 |
| Парткод: | FC0-3654-000 |
| Деталь: | MOUNT, POSITIONING |
| Парткод: | FC8-7940-000 |
| Деталь: | HOLDER, DEVELOPING COUPLING |
| Парткод: | FC8-8085-000 |
| Деталь: | HOLDER, LINK |
| Парткод: | FC8-8369-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1980-000 |
| Деталь: | GUARD, EDGE |
| Парткод: | FC8-8474-000 |
| Деталь: | RACK, M.P. STOPPER |
| Парткод: | FC8-8493-000 |
| Деталь: | COVER, RACK |
| Парткод: | FC8-8494-000 |
| Деталь: | MOUNT, HIGH VOLTAGE CASE |
| Парткод: | FC8-8594-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | SHUTTER, EXHAUST |
| Парткод: | FE2-2091-000 |
| Деталь: | MAIN CABLE ASSEMBLY |
| Парткод: | FM0-1652-000 |
| Деталь: | FEED DRIVER PCB ASSEMBLY |
| Парткод: | FM0-1899-000 |
| Деталь: | CABLE, CONNECTING |
| Парткод: | FM0-1919-000 |
| Деталь: | CABLE, CONNECTING |
| Парткод: | FM0-1920-000 |
| Деталь: | STOPPER ASSEMBLY |
| Парткод: | FM3-8047-000 |
| Деталь: | WASTE TONER FEED ASSEMBLY |
| Парткод: | FM3-8157-000 |
| Деталь: | HIGH VOLTAGE HOLDER ASSY |
| Парткод: | FM3-8160-000 |
| Деталь: | H.V. HOLDER ASSY, AUXILIARY |
| Парткод: | FM3-8161-000 |
| Деталь: | H.V. CONTACT GUIDE ASSY, Y |
| Парткод: | FM3-8162-000 |
| Деталь: | H.V. CONTACT GUIDE ASSY, MCK |
| Парткод: | FM3-8163-000 |
| Деталь: | 1ST TRANSFER H.V. PCB ASSEMBLY |
| Парткод: | FM3-8599-000 |
| Деталь: | 2ND TRANSFER H.V. PCB ASSEMBLY |
| Парткод: | FM3-8610-000 |
| Деталь: | CABLE, FIXING HEATER |
| Парткод: | FM3-8639-000 |
| Деталь: | CABLE, 2ND TRANSFER H.V. |
| Парткод: | FM4-1902-000 |
| Деталь: | CABLE, RIGHT DOOR DETECT |
| Парткод: | FM4-1908-000 |
| Деталь: | CABLE, DRIVE CONNECTING |
| Парткод: | FM4-1911-000 |
| Деталь: | GEAR, 18T/29T |
| Парткод: | FU0-0181-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2779-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2793-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2809-000 |
| Деталь: | REVERSE DRIVE ASSEMBLY |
| Парткод: | RM1-6005-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7173-005 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-006 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-004 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-008 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-014 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-009 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6391-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FE2-1802-000 |
| Деталь: | MACHINE REAR PLATE 2 |
| Парткод: | NPN |
| Деталь: | COVER, TRAY, LOWER |
| Парткод: | FL3-2450-000 |
| Деталь: | GUIDE, TRAY, FRONT |
| Парткод: | FL3-2937-000 |
| Деталь: | RACK, TRAY |
| Парткод: | FC9-4983-000 |
| Деталь: | HOLDER, TRAY VOLUME |
| Парткод: | FC8-6338-000 |
| Деталь: | LEVER, TRAY SENSOR |
| Парткод: | FC8-6339-000 |
| Деталь: | RACK, TRAY |
| Парткод: | FC8-6340-000 |
| Деталь: | VARIABLE RESISTOR UNIT |
| Парткод: | FM0-1200-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | TRAY, DOCUMENT |
| Парткод: | FL3-2449-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC8-6341-000 |
| Деталь: | GUIDE, TRAY, REAR |
| Парткод: | FL3-2939-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FU7-8443-000 |
| Деталь: | GEAR, 50T |
| Парткод: | FC9-4984-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FU7-8442-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | DOCUMENT TRAY ASSY |
| Парткод: | FM0-3218-000 |
| Деталь: | CAM |
| Парткод: | FC8-8328-000 |
| Деталь: | LABEL, GRIP |
| Парткод: | FC8-8449-000 |
| Деталь: | COVER, THIRD DELIVERY BLANKING |
| Парткод: | FL3-1186-000 |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000 |
| Деталь: | SHAFT |
| Парткод: | FC8-8327-000 |
| Деталь: | 2ND/3RD PAPER DELIVERY ASSY |
| Парткод: | FM3-8050-010 |
| Деталь: | GUIDE, PRE-FIXING |
| Парткод: | FC8-8146-000 |
| Деталь: | DUPLEXING GUIDE ASSEMBLY |
| Парткод: | FM3-8071-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2529-000 |
| Деталь: | LINK, RIGHT DOOR, FRONT |
| Парткод: | FC8-8246-000 |
| Деталь: | LINK, RIGHT DOOR |
| Парткод: | FC8-8351-000 |
| Деталь: | ARM, RELEASE |
| Парткод: | FC8-8352-000 |
| Деталь: | RAIL, I.T.B. GUIDE, FRONT, 3 |
| Парткод: | FC8-8480-000 |
| Деталь: | RAIL, DOOR LINK |
| Парткод: | FC8-8513-000 |
| Деталь: | GUIDE, ARM |
| Парткод: | FC8-8514-000 |
| Деталь: | LABEL, I.T.B. CAUTION |
| Парткод: | FC9-8615-000 |
| Деталь: | REGISTRATION SENSING ASSEMBLY |
| Парткод: | FM3-8117-020 |
| Деталь: | POWER DISPATCHING ASSY, 1 |
| Парткод: | FM3-8166-000 |
| Деталь: | POWER DISPATCHING ASSY, 2 |
| Парткод: | FM3-8167-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2761-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2764-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2775-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2796-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2802-000 |
| Деталь: | RAIL, DOOR LINK, FRONT LOWER |
| Парткод: | FE2-2003-000 |
| Деталь: | LINK,I.T.BELT COUPLING RELEASE |
| Парткод: | FE2-2040-000 |
| Деталь: | COVER, DUPLEXING GEAR |
| Парткод: | FE2-2044-000 |
| Деталь: | HOOK, DUPLEXING SPRING |
| Парткод: | FE2-2045-000 |
| Деталь: | RAIL, I.T.BELT GUIDE |
| Парткод: | FC0-2640-000 |
| Деталь: | SUPPORT, FRAME |
| Парткод: | FE2-1990-000 |
| Деталь: | SUPPORT, FRAME |
| Парткод: | FE2-2016-000 |
| Деталь: | LEVER, PUSH |
| Парткод: | FE2-2099-000 |
| Деталь: | LEVER, LIFT, 1 |
| Парткод: | FE2-2100-000 |
| Деталь: | LEVER, LIFT, 2 |
| Парткод: | FE2-2101-000 |
| Деталь: | SLIDER, PUSH |
| Парткод: | FE2-2102-000 |
| Деталь: | GUIDE, SLIDE |
| Парткод: | FE2-2103-000 |
| Деталь: | COVER, GUIDE |
| Парткод: | FE2-2027-000 |
| Деталь: | DUCT, JOINT |
| Парткод: | FE2-1995-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-3298-000 |
| Деталь: | PLATE, LOCK, FRONT |
| Парткод: | RL1-2235-000 |
| Деталь: | PLATE, 2ND TRNSFR. LOCK |
| Парткод: | RL1-2236-000 |
| Деталь: | PLATE, DUPLEXING DRIVE GEAR |
| Парткод: | RL1-2266-000 |
| Деталь: | PAPER DELIVERY ASSY |
| Парткод: | RM1-8830-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU0-0178-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU0-0179-000 |
| Деталь: | GEAR, 74T |
| Парткод: | FU0-0180-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2514-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-011 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-017 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-006 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-019 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1561-000 |
| Деталь: | PLATE, RIGHT DOOR LINK, FRONT |
| Парткод: | FC8-8245-000 |
| Деталь: | STOPPER, RIGHT DOOR LINK,FRONT |
| Парткод: | FC8-8247-000 |
| Деталь: | STOPPER, RIGHT DOOR LINK, REAR |
| Парткод: | FC8-8349-000 |
| Деталь: | PLATE, RIGHT DOOR LINK, REAR |
| Парткод: | FC8-8350-000 |
| Деталь: | SHEET, PRE-FIXING GUIDE |
| Парткод: | FC0-6693-000 |
| Деталь: | CABLE,PAPER DELIVERY GUIDE,LW. |
| Парткод: | FM0-1915-000 |
| Деталь: | SPACER, POSITIONING |
| Парткод: | FE3-3948-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1980-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | SPACER |
| Парткод: | FC0-3637-000 |
| Деталь: | PAPER PICK-UP ROLLER ASSY |
| Парткод: | FM0-3173-000 |
| Деталь: | PAPER PICK-UP GEAR ASSEMBLY |
| Парткод: | RM1-6034-000 |
| Деталь: | SOLENOID |
| Парткод: | RM1-6789-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | IC,PHOTO-INTERRUPTER,LG248NL1A |
| Парткод: | WG8-5783-000 |
| Деталь: | PAPER PICK-UP ASSEMBLY |
| Парткод: | FM0-1658-000 |
| Деталь: | FAN |
| Парткод: | FK2-9244-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 1 |
| Парткод: | FM0-2661-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 1 |
| Парткод: | FM0-2663-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 1 |
| Парткод: | FM0-2662-000 |
| Деталь: | HOLDER, PAPER PICK-UP ROLLER |
| Парткод: | FC0-6755-000 |
| Деталь: | GUIDE, VERTICAL PATH |
| Парткод: | FB6-3387-000 |
| Деталь: | ROD, SEPARATION ROLLER RELEASE |
| Парткод: | FB6-3388-000 |
| Деталь: | CLAW, PICK-UP |
| Парткод: | FB6-3389-000 |
| Деталь: | GEAR, RATCHET |
| Парткод: | FB6-3391-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FB6-3392-020 |
| Деталь: | ARM, PAPER FEED SHAFT |
| Парткод: | FB6-3395-000 |
| Деталь: | LOCK, PICK-UP |
| Парткод: | FB6-3396-010 |
| Деталь: | FLAG, PAPER SENSOR |
| Парткод: | FB6-3397-000 |
| Деталь: | FLAG, PAPER DETECT SENSOR |
| Парткод: | FB6-3398-000 |
| Деталь: | GEAR, RATCHET |
| Парткод: | FB6-3402-000 |
| Деталь: | COUPLING, FEED SHAFT STOP |
| Парткод: | FB6-3403-000 |
| Деталь: | COUPLING, SEPARATION SHAFT |
| Парткод: | FB6-3404-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FB6-3405-000 |
| Цена: | 550 ₽ |
| Деталь: | COLLAR, PAPER PICK-UP SHAFT |
| Парткод: | FB6-3413-000 |
| Деталь: | ROLLER, VERTICAL PATH |
| Парткод: | FB6-4852-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0289-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FC6-6661-000 |
| Цена: | 600 ₽ |
| Деталь: | ROLLER, FEED/SEPARATION |
| Парткод: | FC6-7083-000 |
| Деталь: | RING, RETAINING |
| Парткод: | FC6-9867-000 |
| Деталь: | PAD, PAPER PICK-UP HOLDER |
| Парткод: | FC8-1205-000 |
| Деталь: | STOPPER, ROLLER |
| Парткод: | FC7-5845-000 |
| Деталь: | CLAW, PAPER PICK-UP |
| Парткод: | FC8-1178-000 |
| Деталь: | DAMPER |
| Парткод: | FC8-1202-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FC8-8621-000 |
| Деталь: | JOINT, RETARD |
| Парткод: | FC9-4290-010 |
| Деталь: | ARM, LIFTING |
| Парткод: | FC9-7253-000 |
| Деталь: | GEAR ASSY |
| Парткод: | FL3-6661-000 |
| Деталь: | PHOTO-INTERRUPTER, TLP1252(C6) |
| Парткод: | FK2-0149-000 |
| Деталь: | SOLENOID |
| Парткод: | FK2-0408-000 |
| Деталь: | FLAG, REGISTRATION SENSOR |
| Парткод: | FL3-8032-000 |
| Деталь: | PICK-UP ARM UNIT |
| Парткод: | FM3-4146-000 |
| Деталь: | PICK-UP DRIVE SIDE PLATE ASSY |
| Парткод: | FM4-1201-000 |
| Деталь: | HOLDER, SEPARATION ROLLER |
| Парткод: | FM4-2525-000 |
| Деталь: | BUSHING |
| Парткод: | FS1-1205-000 |
| Деталь: | BUSHING |
| Парткод: | FS5-1943-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FS7-2800-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FS7-2801-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FS7-2803-000 |
| Деталь: | GEAR, 15T |
| Парткод: | FU0-0043-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0282-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0283-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU3-0284-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU3-0288-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU3-0289-000 |
| Деталь: | GEAR, 41T |
| Парткод: | FU3-0347-000 |
| Деталь: | GEAR, 41T |
| Парткод: | FU3-0349-000 |
| Деталь: | GEAR, 41T/41T |
| Парткод: | FU3-0350-000 |
| Деталь: | GEAR, 16T/16T |
| Парткод: | FU3-0352-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1763-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU6-2684-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU6-2784-000 |
| Деталь: | GEAR, 42T |
| Парткод: | FU7-0445-000 |
| Деталь: | GEAR, 46T |
| Парткод: | FU8-0214-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-5378-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | SCREW,RS,M3X10 |
| Парткод: | XA9-0656-000 |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000 |
| Деталь: | PAPER PICK-UP ASSEMBLY |
| Парткод: | FM0-4814-000 |
| Деталь: | ROLLER, BOTTLE TRAY |
| Парткод: | FC8-4649-000 |
| Деталь: | HINGE |
| Парткод: | FC8-7951-000 |
| Деталь: | COVER, SIDE, BLACK |
| Парткод: | FC8-7952-000 |
| Деталь: | COVER, SIDE, COLOR |
| Парткод: | FC8-7971-000 |
| Деталь: | LEVER, LINK, 1 |
| Парткод: | FC8-7958-000 |
| Деталь: | LEVER, LINK, 2, BLACK |
| Парткод: | FC8-7989-000 |
| Деталь: | LEVER, LINK, 2, COLOR |
| Парткод: | FC8-7959-000 |
| Деталь: | COVER, BOTTLE, BLACK |
| Парткод: | FC8-7963-000 |
| Деталь: | COVER, BOTTLE, COLOR |
| Парткод: | FC8-7975-000 |
| Деталь: | GUIDE, BOTTLE INSERT, BLACK |
| Парткод: | FC8-7964-000 |
| Деталь: | GUIDE, BOTTLE INSERT, COLOR |
| Парткод: | FC8-7976-000 |
| Деталь: | PLATE, INSERT GUIDE, BLACK |
| Парткод: | FC8-7965-000 |
| Деталь: | PLATE, INSERT GUIDE, COLOR |
| Парткод: | FC8-7977-000 |
| Деталь: | LEVER, BOTTLE SENSING |
| Парткод: | FC8-7981-000 |
| Деталь: | PLATE, LINK FIXED, 1 |
| Парткод: | FC8-7988-000 |
| Деталь: | PLATE, LINK FIXED, 2 |
| Парткод: | FC8-7990-000 |
| Деталь: | LABEL, COLOR INDICATION |
| Парткод: | FC8-7994-000 |
| Деталь: | BRUSH, CLEANING |
| Парткод: | FC0-3643-000 |
| Деталь: | DEVELOPING DOOR ASSEMBLY |
| Парткод: | FM3-8109-000 |
| Деталь: | RAIL ASSEMBLY |
| Парткод: | FM3-8110-000 |
| Деталь: | BOTTLE BASE ASSEMBLY, BLACK |
| Парткод: | FM3-8142-000 |
| Деталь: | BOTTLE BASE ASSEMBLY, COLOR |
| Парткод: | FM3-8144-000 |
| Деталь: | LEVER, LEFT, BLACK |
| Парткод: | FC9-8649-000 |
| Деталь: | LEVER, LEFT, COLOR |
| Парткод: | FC9-8651-000 |
| Деталь: | LEVER, RIGHT, BLACK |
| Парткод: | FC9-8650-000 |
| Деталь: | LEVER, RIGHT, COLOR |
| Парткод: | FC9-8652-000 |
| Деталь: | TONER FEED ASSEMBLY, BLACK |
| Парткод: | FM3-8084-010 |
| Деталь: | TONER FEED ASSEMBLY, COLOR |
| Парткод: | FM3-8085-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2823-000 |
| Деталь: | CONTACT HOLDER UNIT |
| Парткод: | FM3-8111-000 |
| Деталь: | SWITCH CABLE UNIT, BOTTLE |
| Парткод: | FM3-8636-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2749-000 |
| Деталь: | DEVELOPING CROSSMEMBER ASSY |
| Парткод: | FM3-8108-000 |
| Деталь: | INTERNAL COMPONENTS 5 |
| Парткод: | NPN |
| Деталь: | SHAFT |
| Парткод: | FC0-0618-000 |
| Деталь: | LINK, HANDLE |
| Парткод: | FC0-0619-000 |
| Деталь: | LEVER, LINK |
| Парткод: | FC0-0620-000 |
| Деталь: | LATCH, FRONT |
| Парткод: | FC0-0622-000 |
| Деталь: | LATCH, REAR |
| Парткод: | FC0-0623-000 |
| Деталь: | HOLDER, LATCH, FRONT |
| Парткод: | FC0-0624-000 |
| Деталь: | HOLDER, LATCH, REAR |
| Парткод: | FC0-0625-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | HOOK |
| Парткод: | FC0-0627-000 |
| Деталь: | LEVER, LOCK |
| Парткод: | FC0-0628-000 |
| Деталь: | SHEET, BASE GUIDE |
| Парткод: | FC0-0629-000 |
| Деталь: | PIN, PRESSURE |
| Парткод: | FC0-0630-000 |
| Деталь: | STOPPER, PAPER DELIVERY GUIDE |
| Парткод: | FC8-8226-000 |
| Деталь: | STOPPER |
| Парткод: | FC8-8241-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FC8-8348-000 |
| Деталь: | LABEL, LASER CAUTION |
| Парткод: | FC8-8355-000 |
| Деталь: | FLAG, OPEN/CLOSE SENSOR |
| Парткод: | FC8-8356-000 |
| Деталь: | PIN, POSITIONING |
| Парткод: | FC8-8413-000 |
| Деталь: | ROLLER, REEL |
| Парткод: | FC8-8492-000 |
| Деталь: | SHEET, NOISE-PROOF |
| Парткод: | FC8-8524-000 |
| Деталь: | SHAFT, HANDLE FIXED |
| Парткод: | FC8-8538-000 |
| Деталь: | HANDLE |
| Парткод: | FC8-8539-000 |
| Деталь: | COVER, PAPER PICK-UP ROLLER |
| Парткод: | FE2-1999-000 |
| Деталь: | MULTI PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-8038-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2768-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2782-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2792-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2797-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2798-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2799-000 |
| Деталь: | SPRING, POWER DISPATCHING |
| Парткод: | FU7-2800-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU7-2801-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2803-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2804-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2805-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2814-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2819-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2820-000 |
| Деталь: | CLAMP, LEVER, REAR |
| Парткод: | FE2-2083-000 |
| Деталь: | STOPPER, PAPER PICK-UP SHAFT |
| Парткод: | FE2-2088-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2519-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE2-2025-000 |
| Деталь: | COVER, GEAR |
| Парткод: | FE2-1989-000 |
| Деталь: | HOOK, SPRING, LEFT |
| Парткод: | FE2-2047-000 |
| Деталь: | PIN, SPRING HOOK |
| Парткод: | FE2-2048-000 |
| Деталь: | HOOK, SPRING, RIGHT |
| Парткод: | FE2-2049-000 |
| Деталь: | LINK, M.P. HINGE |
| Парткод: | FE2-2050-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE2-1975-000 |
| Деталь: | CLIP |
| Парткод: | FE2-2110-000 |
| Деталь: | COVER, GROUNDING |
| Парткод: | FE2-1992-000 |
| Деталь: | ROLLER, DUPLEXING PAPER FEED |
| Парткод: | RC2-7271-000 |
| Деталь: | ROLLER, REG. |
| Парткод: | RC2-7280-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2521-000 |
| Деталь: | HOOK, FRONT |
| Парткод: | FE2-2115-000 |
| Деталь: | HOOK, REAR |
| Парткод: | FE2-2116-000 |
| Деталь: | GUIDE, CONDUCTIVE |
| Парткод: | FE2-2117-000 |
| Деталь: | HOOK |
| Парткод: | FE2-2118-000 |
| Деталь: | COVER, CABLE |
| Парткод: | FE2-1996-000 |
| Деталь: | SECONDARY TRANSFER GUIDE ASSY |
| Парткод: | RM1-6041-000 |
| Деталь: | M.P. PAPER PICK-UP GEAR ASSY |
| Парткод: | RM1-6049-000 |
| Деталь: | M.P. PAPER PICK-UP SHAFT ASSY |
| Парткод: | RM1-6050-000 |
| Деталь: | MP LIFTER PLATE ASSY |
| Парткод: | RM1-6124-000 |
| Деталь: | DUPLEXING GEAR COVER ASSEMBLY |
| Парткод: | RM1-6151-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | RL1-2244-000 |
| Цена: | 2 900 ₽ |
| Деталь: | MULTI-PURPOSE SEP. PAD KIT |
| Парткод: | RM1-6163-040 |
| Деталь: | 2ND TRANSFER ROLLER ASSY |
| Парткод: | RM1-7928-000 |
| Деталь: | SOLENOID |
| Парткод: | RM1-6790-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1110-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1578-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1579-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1580-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1581-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU0-0198-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU0-0183-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2526-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2693-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2516-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU9-2530-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2528-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-007 |
| Деталь: | LABEL, FEED SIZE |
| Парткод: | FE2-1822-000 |
| Деталь: | LABEL, FEED SIZE |
| Парткод: | FE2-1823-000 |
| Деталь: | LABEL, FEED SIZE |
| Парткод: | FE2-1824-000 |
| Деталь: | LABEL, PAPER SET INSTRUCTION |
| Парткод: | FC9-8584-000 |
| Деталь: | LABEL, PAPER SET INSTRUCTION |
| Парткод: | FC9-8585-000 |
| Деталь: | GUIDE, RIGHT DOOR, UPPER |
| Парткод: | FC8-8235-000 |
| Деталь: | GUIDE, PAPER DELIVERY, 1 |
| Парткод: | FC8-8251-000 |
| Деталь: | GUIDE, PAPER DELIVERY, 2 |
| Парткод: | FC8-8252-000 |
| Деталь: | HINGE, RIGHT DOOR, REAR |
| Парткод: | FC8-8353-000 |
| Деталь: | INNER GUIDE ASSEMBLY |
| Парткод: | FM3-8039-000 |
| Деталь: | PLATE, POWER DISPATCHING |
| Парткод: | FE2-1976-000 |
| Деталь: | RIGHT DOOR ASSEMBLY |
| Парткод: | FM3-8036-000 |
| Деталь: | COVER, MAIN SWITCH |
| Парткод: | FC8-4000-000 |
| Деталь: | PLATE, 2ND DELIV. TRAY SUPPORT |
| Парткод: | FC8-5363-000 |
| Деталь: | MOUNT, SWITCH COVER |
| Парткод: | FC8-5378-000 |
| Деталь: | DOOR ASSEMBLY, RIGHT LOWER |
| Парткод: | FM3-8150-000 |
| Деталь: | COVER, RIGHT REAR SUB |
| Парткод: | FC8-8444-000 |
| Деталь: | COVER, INNER SUB, 1 |
| Парткод: | FC8-8186-000 |
| Деталь: | COVER, 1ST PAPER DELIVERY |
| Парткод: | FC8-8187-000 |
| Деталь: | TRAY, 1ST PAPER DELIVERY |
| Парткод: | FE2-0330-000 |
| Деталь: | COVER, RIGHT LOWER SUB, 2 |
| Парткод: | FC8-8190-000 |
| Деталь: | COVER, RIGHT LOWER SUB, 1 |
| Парткод: | FC8-8191-000 |
| Деталь: | COVER, REAR UPPER, 1 |
| Парткод: | FC8-8192-010 |
| Деталь: | COVER, INNER REAR, 2 |
| Парткод: | FC8-8193-010 |
| Деталь: | COVER, REAR |
| Парткод: | FC8-8196-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FC9-7297-000 |
| Деталь: | COVER, LEFT LOWER |
| Парткод: | FC8-8198-000 |
| Деталь: | COVER, GRIP |
| Парткод: | FC8-8201-000 |
| Деталь: | ARM, FRONT COVER, B |
| Парткод: | FC8-8203-000 |
| Деталь: | MOUNT, STOPPER ARM |
| Парткод: | FC8-8204-000 |
| Деталь: | HOOK, COVER, FRONT |
| Парткод: | FC8-8205-000 |
| Деталь: | COVER, INNER REAR, 1 |
| Парткод: | FC8-8207-010 |
| Деталь: | COVER, RIGHT FRONT SUB |
| Парткод: | FC8-8443-000 |
| Деталь: | COVER, REAR UPPER, 3 |
| Парткод: | FC8-8286-000 |
| Деталь: | COVER, INNER SUB, 2 |
| Парткод: | FC8-8290-000 |
| Деталь: | COVER, REAR RIGHT, SMALL |
| Парткод: | FE2-0329-000 |
| Деталь: | PLATE, FRONT DOOR FIXED |
| Парткод: | FC8-8512-000 |
| Деталь: | PLATE, STATIC CHARGE, LEFT |
| Парткод: | FC8-8638-000 |
| Деталь: | PLATE, STATIC CHARGE, RIGHT |
| Парткод: | FC8-8637-000 |
| Деталь: | COVER, CONNECTOR, 1 |
| Парткод: | FC8-8344-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FC8-8346-000 |
| Деталь: | COVER, HARD DISK DRIVE |
| Парткод: | FC8-8359-000 |
| Деталь: | COVER, INNER BOTTOM |
| Парткод: | FC8-8445-000 |
| Деталь: | ROLLER, BOTTLE TRAY |
| Парткод: | FC8-4649-000 |
| Деталь: | GUIDE, REVERSE BACK END |
| Парткод: | FC9-8612-000 |
| Деталь: | COVER, 2ND PAPER DELIVERY |
| Парткод: | FC8-8543-000 |
| Деталь: | COVER, LEFT FRONT |
| Парткод: | FE2-0541-000 |
| Деталь: | LABEL, TONER MODEL |
| Парткод: | FC8-8622-000 |
| Деталь: | LABEL, TONER MODEL |
| Парткод: | FC8-8623-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2759-000 |
| Деталь: | COVER, LEFT FRONT, UPPER |
| Парткод: | FE2-0542-000 |
| Деталь: | COVER, RIGHT LOWER SUB, 3 |
| Парткод: | FC8-8617-000 |
| Деталь: | STOPPER, RAIL |
| Парткод: | FE2-0531-000 |
| Деталь: | LABEL, MAIN POWER SUPPLY |
| Парткод: | FC9-7863-000 |
| Деталь: | LABEL, MAIN POWER SUPPLY |
| Парткод: | FC9-7862-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1035-000 |
| Деталь: | COVER, SLOT |
| Парткод: | FC8-8645-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FC0-2633-000 |
| Деталь: | EMBLEM |
| Парткод: | FL3-1185-000 |
| Деталь: | FRONT UPPER COVER ASSEMBLY |
| Парткод: | FM3-8077-000 |
| Деталь: | FRONT DOOR ASSEMBLY |
| Парткод: | FM3-8078-000 |
| Деталь: | LEFT REAR COVER ASSEMBLY |
| Парткод: | FM3-8079-010 |
| Деталь: | LABEL, LASER CAUTION |
| Парткод: | FC0-2901-000 |
| Деталь: | LABEL, GROUNDING CAUTION |
| Парткод: | FU7-8521-000 |
| Деталь: | RIGHT UPPER SUB COVER ASSEMBLY |
| Парткод: | FM3-8083-000 |
| Деталь: | LABEL, HARD DISK DRIVE CAUTION |
| Парткод: | FU7-8471-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FS7-2788-000 |
| Деталь: | HINGE, RIGHT DOOR, FRONT |
| Парткод: | FC8-8228-000 |
| Деталь: | HOLDER, M.P. STOPPER |
| Парткод: | FC8-8240-000 |
| Деталь: | COVER, CASSETTE RIGHT UPPER, 1 |
| Парткод: | FC8-8515-000 |
| Деталь: | COVER, CASSETTE RIGHT UPPER, 2 |
| Парткод: | FC8-8516-000 |
| Деталь: | COVER, WASTE TONER |
| Парткод: | FC8-8341-000 |
| Деталь: | SHEET, GLASS CLEANING |
| Парткод: | FC8-8634-000 |
| Деталь: | PAD, GLASS CLEANING |
| Парткод: | FC8-8635-000 |
| Деталь: | GLASS CLEANING ARM ASSEMBLY |
| Парткод: | FM3-8260-000 |
| Деталь: | HOOK, RIGHT DOOR |
| Парткод: | FC5-0631-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FC8-3782-000 |
| Деталь: | STOPPER, DOOR, RIGHT LOWER |
| Парткод: | FC8-5164-000 |
| Деталь: | HANDLE, DOOR |
| Парткод: | FC8-8172-000 |
| Деталь: | COVER, ENV. HEATER SWITCH |
| Парткод: | FC8-4137-000 |
| Деталь: | COVER, RIGHT UPPER |
| Парткод: | FC8-8291-000 |
| Деталь: | COVER, REVERSE BLANKING |
| Парткод: | FC8-8544-000 |
| Деталь: | COVER, REAR UPPER, 2 |
| Парткод: | FC8-8631-000 |
| Деталь: | SHEET, EXTRACTION ROLLER |
| Парткод: | FE3-3788-000 |
| Деталь: | SHEET, RIGHT DOOR, LOWER |
| Парткод: | FE3-4452-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | ROLLER, REGISTRATION, 1 |
| Парткод: | FC5-4323-000 |
| Деталь: | ROLLER, REGISTRATION, 2 |
| Парткод: | FC5-4324-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | LEVER, WIDTH SENSOR |
| Парткод: | FC9-4973-000 |
| Деталь: | LED PCB UNIT |
| Парткод: | FM0-1189-000 |
| Деталь: | SENSOR PCB ASSY |
| Парткод: | FM4-1747-000 |
| Деталь: | LEVER, TIMING SENSOR |
| Парткод: | FC8-6348-000 |
| Деталь: | GEAR, 33T |
| Парткод: | FU8-0890-000 |
| Деталь: | SHUTTER |
| Парткод: | FL2-9948-000 |
| Деталь: | COVER, PAPER PICK-UP |
| Парткод: | FL3-7543-000 |
| Деталь: | DAMPER, REV. GUIDE RETAINING |
| Парткод: | FC8-6403-000 |
| Деталь: | GUIDE, PAPER PICK-UP, LOWER |
| Парткод: | FL3-8437-000 |
| Деталь: | PAPER PICK-UP ROLLER UNIT |
| Парткод: | FM0-1226-000 |
| Деталь: | ROLLER, PAPER SEPARATION |
| Парткод: | FC6-2784-000 |
| Деталь: | LEVER, STOP |
| Парткод: | FC6-8971-010 |
| Деталь: | ARM, PICK, FRONT |
| Парткод: | FC0-9108-000 |
| Деталь: | ARM, PICK, REAR |
| Парткод: | FC0-9109-000 |
| Деталь: | JOINT |
| Парткод: | FC8-6353-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC9-4968-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE2-1596-000 |
| Деталь: | GEAR, 20T |
| Парткод: | FU8-0299-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0300-000 |
| Деталь: | GEAR, 33T |
| Парткод: | FC9-4970-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1626-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2654-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2655-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2656-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU9-0938-000 |
| Деталь: | LEVER, EMPTY SENSOR |
| Парткод: | FC9-4971-000 |
| Деталь: | KNOB, PAPER PICK-UP COVER |
| Парткод: | FC9-6190-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD3-2200-102 |
| Деталь: | PAPER PICK-UP COVER ASSEMBLY |
| Парткод: | FM0-3223-000 |
| Деталь: | WINDOW, CST FR. COVER IND. |
| Парткод: | FC8-4967-000 |
| Деталь: | BUTTON, PUSHING |
| Парткод: | FC8-4985-000 |
| Деталь: | CASSETTE ASSEMBLY |
| Парткод: | RM1-6150-000 |
| Деталь: | COVER, CASSETTE FRONT |
| Парткод: | FC8-8181-010 |
| Деталь: | RING, BUTTON |
| Парткод: | FC8-8182-000 |
| Деталь: | LABEL, PAPER SIZE, BACK END |
| Парткод: | FC8-8596-000 |
| Деталь: | LABEL, PAPER SIZE, SIDE |
| Парткод: | FC8-8597-000 |
| Деталь: | LABEL, PAPER PICK-UP OPERATION |
| Парткод: | FC8-8616-000 |
| Деталь: | COVER, SIZEPLATE |
| Парткод: | FC9-4042-000 |
| Деталь: | BUTTON LINK ASSEMBLY |
| Парткод: | FM3-8046-000 |
| Деталь: | CASSETTE ASSEMBLY |
| Парткод: | NPN |
| Деталь: | FLAG, REVERSE SENSOR |
| Парткод: | FC5-0987-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-0988-000 |
| Деталь: | ROLLER, REVERSE |
| Парткод: | FC8-4749-000 |
| Деталь: | BUSHING |
| Парткод: | FC8-4751-000 |
| Деталь: | IC,PHOTO-INTERRUPTER,LG248NL1A |
| Парткод: | WG8-5783-000 |
| Деталь: | HOLDER, TOGGLE |
| Парткод: | FC8-8320-000 |
| Деталь: | COVER, 2ND/3RD DELIVERY, LOWER |
| Парткод: | FC8-8323-000 |
| Деталь: | ROLLER, REVERSE |
| Парткод: | FC8-8326-000 |
| Деталь: | GUIDE, SWING GEAR |
| Парткод: | FC8-8333-000 |
| Деталь: | CLAMP, SWING GEAR |
| Парткод: | FC8-8334-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FC8-8447-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-0997-000 |
| Деталь: | GUIDE, MOVABLE |
| Парткод: | FC8-8625-000 |
| Деталь: | 2ND/3RD DELIVERY PCB ASSEMBLY |
| Парткод: | FM3-8601-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1453-000 |
| Деталь: | BUSHING, POLYACETAR |
| Парткод: | FU5-1469-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU6-0085-000 |
| Деталь: | GEAR, 31T/20T |
| Парткод: | FU6-0140-000 |
| Деталь: | SPRING |
| Парткод: | FU7-2446-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2770-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2784-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2818-000 |
| Деталь: | GEAR, 32T/19T |
| Парткод: | FU8-0398-000 |
| Деталь: | GEAR, 74T/25T |
| Парткод: | FU8-0408-000 |
| Деталь: | LEVER, TOGGLE |
| Парткод: | FE2-2086-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FC0-3650-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0239-000 |
| Деталь: | 2ND/3RD DRIVE FRAME ASSEMBLY |
| Парткод: | FM3-8051-000 |
| Деталь: | SHEET, CABLE RETAINING |
| Парткод: | FC0-0463-000 |
| Деталь: | COVER, HINGE LOWER, LEFT |
| Парткод: | FC0-0472-000 |
| Деталь: | COVER, HINGE LOWER, RIGHT |
| Парткод: | FC0-0473-000 |
| Деталь: | FLAG, OPEN/CLOSE SENSOR |
| Парткод: | FC0-0679-000 |
| Деталь: | COVER, READER, FRONT |
| Парткод: | FC0-0681-000 |
| Деталь: | SHEET, HINGE COVER |
| Парткод: | FC0-0691-000 |
| Деталь: | COVER, GLASS SUPPORT |
| Парткод: | FC0-2618-000 |
| Деталь: | PULLEY |
| Парткод: | FC8-6163-000 |
| Деталь: | PULLEY |
| Парткод: | FC8-6180-000 |
| Деталь: | COVER, GLASS RETAINING |
| Парткод: | FC9-7288-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FC9-7297-000 |
| Деталь: | SEAL, CABLE BLANKING |
| Парткод: | FC9-7300-000 |
| Деталь: | COVER, READER SUB, FRONT |
| Парткод: | FC9-7301-000 |
| Деталь: | COVER, PCB |
| Парткод: | FE2-1747-000 |
| Деталь: | SPACER, SHAFT CUSHION |
| Парткод: | FE2-1752-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-0860-000 |
| Деталь: | IC, PHOTO SENSOR,DOCUMENT SIZE |
| Парткод: | FK3-0871-000 |
| Деталь: | GLASS, READER |
| Парткод: | FL3-3206-000 |
| Деталь: | COVER, READER, REAR |
| Парткод: | FL3-4603-000 |
| Деталь: | COVER, GLASS RETAINING |
| Парткод: | FL3-4761-000 |
| Деталь: | GLASS, COPYBOARD |
| Парткод: | FL3-4767-000 |
| Деталь: | GLASS, COPYBOARD |
| Парткод: | FL3-4768-000 |
| Деталь: | COVER, SIDE, RIGHT |
| Парткод: | FL3-4771-000 |
| Деталь: | LABEL, SERVICE |
| Парткод: | FL3-4774-000 |
| Деталь: | COVER, READER, LEFT |
| Парткод: | FL3-6227-000 |
| Деталь: | CABLE GUIDE ASSEMBLY, B |
| Парткод: | FM0-1283-000 |
| Деталь: | SCANNER UNIT |
| Парткод: | FM0-2743-000 |
| Деталь: | MOTOR ASSY |
| Парткод: | FM4-6171-000 |
| Деталь: | CABLE GUIDE ASSEMBLY, A |
| Парткод: | FM4-6406-000 |
| Деталь: | CABLE, SIZE SENSOR |
| Парткод: | FM4-6431-000 |
| Деталь: | READER CONNECTING PCB ASSEMBLY |
| Парткод: | FM4-6435-000 |
| Деталь: | CABLE, OPTICAL MOTOR |
| Парткод: | FM4-6437-000 |
| Деталь: | PULLEY |
| Парткод: | FU5-3710-000 |
| Деталь: | LABEL, CLEANING POSITION |
| Парткод: | FU7-8080-000 |
| Деталь: | LABEL, COPY INHIBITED |
| Парткод: | FU7-8085-000 |
| Деталь: | LABEL, COPY INHIBITED |
| Парткод: | FU7-8086-000 |
| Деталь: | LABEL, COPY INHIBITED |
| Парткод: | FU7-8087-000 |
| Деталь: | LABEL, COPY INHIBITED |
| Парткод: | FU7-8227-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2481-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU8-2497-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2600-000 |
| Деталь: | IC, PHOTO-INTERRUPTER |
| Парткод: | WG8-5848-000 |
| Деталь: | SCREW,M3X5 |
| Парткод: | XA9-1116-030 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | SCREW, FLAT HEAD, M4 |
| Парткод: | XA9-1415-000 |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-4606-835 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-4668-040 |
| Деталь: | SCREW, MACH. TRUSS HEAD, M4X6 |
| Парткод: | XA9-1031-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | NPN |
| Деталь: | SPACER |
| Парткод: | FC0-3637-000 |
| Деталь: | PAPER PICK-UP GEAR ASSEMBLY |
| Парткод: | RM1-6034-000 |
| Деталь: | PAPER PICK-UP ROLLER ASSY |
| Парткод: | RM1-6035-000 |
| Деталь: | SOLENOID |
| Парткод: | RM1-6789-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | PAPER PICK-UP ASSY |
| Парткод: | RM1-6106-070 |
| Деталь: | LEVER, TOGGLE, COLOR |
| Парткод: | FC8-7978-000 |
| Деталь: | LEVER, TOGGLE, BLACK |
| Парткод: | FC8-7979-000 |
| Деталь: | LEVER, HOLD, BLACK |
| Парткод: | FC8-7991-000 |
| Деталь: | LEVER, HOLD, COLOR |
| Парткод: | FC8-7992-000 |
| Деталь: | LEVER, SHUTTER, 1 |
| Парткод: | FC8-8026-000 |
| Деталь: | LEVER, SHUTTER, 2 |
| Парткод: | FC8-8027-000 |
| Деталь: | LEVER, SHUTTER, 3 |
| Парткод: | FC8-8028-000 |
| Деталь: | LINK, SHUTTER, 1 |
| Парткод: | FC8-8032-000 |
| Деталь: | LINK, SHUTTER, 2 |
| Парткод: | FC8-8033-000 |
| Деталь: | GUIDE, CROSSMEMBER, LOWER |
| Парткод: | FC8-8220-000 |
| Деталь: | HOLDER, CONNECTOR |
| Парткод: | FC8-8530-000 |
| Деталь: | GUIDE, FRONT |
| Парткод: | FC8-8606-000 |
| Деталь: | SPRING, RETAINING |
| Парткод: | FC9-8606-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | FK2-9199-000 |
| Деталь: | CAP, SHUTTER LEVER |
| Парткод: | FC8-8029-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2750-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2763-000 |
| Деталь: | GUIDE, 2 |
| Парткод: | FE2-1985-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-005 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-006 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-015 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-027 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-029 |
| Деталь: | LEFT CABLE ASSEMBLY |
| Парткод: | FM3-8182-000 |
| Деталь: | CABLE, BUFFER CONNECTING |
| Парткод: | FM3-8644-000 |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | CAP, WASTE TONER CASE |
| Парткод: | FC8-8363-000 |
| Деталь: | STRAP, WASTE TONER |
| Парткод: | FC8-8496-000 |
| Деталь: | HOLDER, SWITCH, UPPER |
| Парткод: | FC8-8497-000 |
| Деталь: | LEVER, SENSOR |
| Парткод: | FC8-8498-000 |
| Деталь: | HOLDER, SWITCH, LOWER |
| Парткод: | FC8-8499-000 |
| Деталь: | AC CABLE ASSEMBLY |
| Парткод: | FM0-1653-000 |
| Деталь: | HEATER CONNECTING CABLE ASSY |
| Парткод: | FM0-1680-000 |
| Деталь: | HEATER CONNECTING CABLE ASSY |
| Парткод: | FM0-1681-000 |
| Деталь: | DC CONTROLLER PCB ASSEMBLY |
| Парткод: | FM0-1905-000 |
| Деталь: | CABLE, REAR UPPER |
| Парткод: | FM0-1914-000 |
| Деталь: | WASTE TONER CASE ASSEMBLY |
| Парткод: | FM3-8137-010 |
| Деталь: | WASTE TONER INNER CASE ASSY |
| Парткод: | FM3-8138-010 |
| Деталь: | ENVIRONMENT HEATER PCB ASSY |
| Парткод: | FM3-8190-000 |
| Деталь: | CABLE, HEATER |
| Парткод: | FM3-8623-000 |
| Деталь: | SWITCH CABLE UNIT, ENVIRONMENT |
| Парткод: | FM3-8626-000 |
| Деталь: | CABLE, WASTE TONER SENSING |
| Парткод: | FM4-1894-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-004 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-019 |
| Деталь: | CONNECTOR, SNAP TIGHT, 31P, BL |
| Парткод: | VS1-8412-031 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6449-000 |
| Деталь: | PLATE, FIXED |
| Парткод: | FC8-8473-000 |
| Деталь: | MACHINE REAR PLATE 1 |
| Парткод: | NPN |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | DUCT, ESTRANGEMENT HARNESS |
| Парткод: | FC8-6406-000 |
| Деталь: | CAM, ESTRANGEMENT |
| Парткод: | FC8-6407-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK3-2680-000 |
| Деталь: | GEAR PULLEY, 40T/20T |
| Парткод: | FU8-0311-000 |
| Деталь: | GEAR, 31T |
| Парткод: | FU8-0319-000 |
| Деталь: | GEAR, 30T |
| Парткод: | FU9-0930-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW,RS,M4 |
| Парткод: | XA9-0732-010 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1607-640 |
| Деталь: | SPRING, LEAF |
| Парткод: | FC0-4617-000 |
| Деталь: | ESTRANGEMENT DRIVE ASSEMBLY |
| Парткод: | NPN |
| Деталь: | HIGH VOLTAGE PCB ASSEMBLY |
| Парткод: | FM3-8175-000 |
| Деталь: | KEY TOP, SLEEP |
| Парткод: | FC0-5153-000 |
| Деталь: | COVER, UPPER |
| Парткод: | FC0-8966-000 |
| Деталь: | COVER, CONTROL PANEL |
| Парткод: | FC0-8967-000 |
| Деталь: | COVER, LIQUID CRYSTAL DISPLAY |
| Парткод: | FC0-8968-000 |
| Деталь: | SHEET, ANTISTATIC, 1 |
| Парткод: | FC0-8969-000 |
| Деталь: | SHEET, ANTISTATIC, 2 |
| Парткод: | FC0-8970-000 |
| Деталь: | COVER, LCD, 1 |
| Парткод: | FC0-8971-000 |
| Деталь: | COVER, LCD, 2 |
| Парткод: | FC0-8972-000 |
| Деталь: | COVER, LOWER, 1 |
| Парткод: | FL3-9373-000 |
| Деталь: | COVER, LOWER, 2 |
| Парткод: | FC0-8976-000 |
| Деталь: | COVER, LOWER, 3 |
| Парткод: | FC0-8977-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FC0-8988-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FC0-8992-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FC0-8998-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FC0-8999-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FC0-8997-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FC0-9005-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FC0-8993-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FC0-9004-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FC0-8996-000 |
| Деталь: | KEY TOP, BRIGHTNESS ADJUSTMENT |
| Парткод: | FC8-7824-000 |
| Деталь: | KEY TOP, SETTINGS/REGISTRATION |
| Парткод: | FC8-8649-000 |
| Деталь: | KEY TOP, COUNTER CHECK |
| Парткод: | FC8-8655-000 |
| Деталь: | COVER, KEY TOP, RIGHT |
| Парткод: | FC9-4391-000 |
| Деталь: | COVER, LAMP |
| Парткод: | FC9-5284-000 |
| Деталь: | KEY TOP, NUMBERS |
| Парткод: | FC9-5290-000 |
| Деталь: | KEY TOP, VOLUME |
| Парткод: | FC9-6236-000 |
| Деталь: | KEY TOP, STOP |
| Парткод: | FC9-9235-000 |
| Деталь: | KEY TOP, RESET |
| Парткод: | FC9-9237-000 |
| Деталь: | SHEET, SLIDER, 1 |
| Парткод: | FE2-3506-000 |
| Деталь: | SHEET, SLIDER, 2 |
| Парткод: | FE2-3507-000 |
| Деталь: | GUIDE, UI CABLE |
| Парткод: | FE2-3508-000 |
| Деталь: | TOUCH PANEL ASSEMBLY |
| Парткод: | FK3-2815-000 |
| Деталь: | PEN, TOUCH PANEL |
| Парткод: | FL3-0626-000 |
| Деталь: | KEY TOP, START |
| Парткод: | FL3-0833-000 |
| Деталь: | PANEL, LCD |
| Парткод: | FM0-1118-000 |
| Деталь: | PANEL, LCD |
| Парткод: | FM0-1117-000 |
| Деталь: | CPU UNIT |
| Парткод: | FM0-1854-000 |
| Деталь: | NUMBERS KEY PCB ASSEMBLY |
| Парткод: | FM0-1855-000 |
| Деталь: | RAIL, CONTROL PANEL, LEFT |
| Парткод: | FM0-3171-000 |
| Деталь: | RAIL, CONTROL PANEL, RIGHT |
| Парткод: | FM0-3172-000 |
| Деталь: | CONTROL PANEL VOLUME ASSEMBLY |
| Парткод: | FM4-1198-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM0-1665-000 |
| Деталь: | FUSE 125V 10A, 233010.MXP |
| Парткод: | VD7-3221-002 |
| Деталь: | FUSE |
| Парткод: | VD7-2951-502 |
| Деталь: | FUSE |
| Парткод: | VD7-2898-001 |
| Деталь: | AC DRIVER PCB ASSEMBLY |
| Парткод: | FM0-1662-000 |
| Деталь: | AC DRIVER PCB ASSEMBLY |
| Парткод: | FM0-1663-000 |
| Деталь: | DAMPER, DELIVERY |
| Парткод: | FC8-6419-000 |
| Деталь: | ROLLER, PAPER FEED, 1 |
| Парткод: | FC5-4286-000 |
| Деталь: | ROLLER, PAPER FEED, 2 |
| Парткод: | FC5-4287-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | HOLDER, SOLENOID |
| Парткод: | FC8-6319-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FL3-8436-000 |
| Деталь: | ROLLER, READ 2 PINCH |
| Парткод: | FC8-6404-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2652-000 |
| Деталь: | SHEET, PAPER FEED |
| Парткод: | FC8-6422-000 |
| Деталь: | SHEET, PAPER FEED |
| Парткод: | FC8-6423-000 |
| Деталь: | HOLDER, ROLLER, SMALL |
| Парткод: | FL2-9933-000 |
| Деталь: | HOLDER, ROLLER, LARGE |
| Парткод: | FL2-9934-010 |
| Деталь: | COVER, BASE, LOWER |
| Парткод: | FL3-2942-000 |
| Деталь: | LEVER, READ 1 PRESSURE |
| Парткод: | FC8-6331-000 |
| Деталь: | COLLAR, READ 1 PRESSURE |
| Парткод: | FC8-6332-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC9-9203-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1168-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6316-000 |
| Деталь: | HOLDER, DELIVERY ROLLER |
| Парткод: | FC8-6317-000 |
| Деталь: | CAM, DELIVERY ESTRANGEMENT |
| Парткод: | FC8-6318-010 |
| Деталь: | SHAFT, PAPER FEED ROLLER |
| Парткод: | FE2-1601-000 |
| Деталь: | CABLE, BASE |
| Парткод: | FM0-1192-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CABLE, REGISTRATION MOTOR |
| Парткод: | FM0-1197-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-122 |
| Деталь: | BASE ASSEMBLY |
| Парткод: | NPN |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2512-000 |
| Деталь: | ITB GUIDE RAIL ASSY, FRONT, 1 |
| Парткод: | FM3-8013-000 |
| Деталь: | ITB GUIDE RAIL ASSY, REAR, 1 |
| Парткод: | FM3-8014-000 |
| Деталь: | I.T.BELT GUIDE RAIL ASSY, F |
| Парткод: | FM3-8018-000 |
| Деталь: | HANDLE,MAIN BODY |
| Парткод: | FM3-8021-000 |
| Деталь: | RIGHT DOOR TOGGLE ASSY, FRONT |
| Парткод: | FM3-8031-000 |
| Деталь: | RIGHT DOOR TOGGLE ASSY, REAR |
| Парткод: | FM3-8032-000 |
| Деталь: | I.T.BELT GUIDE RAIL ASSY, R |
| Парткод: | FM3-8033-000 |
| Деталь: | LEVER, SWITCHING |
| Парткод: | FE2-2013-000 |
| Деталь: | LOW VOLTAGE POWER SUPPLY ASSY |
| Парткод: | FM3-8179-010 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6449-000 |
| Деталь: | LOCK, DOOR LINK, RIGHT |
| Парткод: | FE2-2106-000 |
| Деталь: | PLATE, RT. DOOR LINK FIXED, FR |
| Парткод: | RL1-2281-000 |
| Деталь: | PLATE, RT. DOOR LINK FIXED, RR |
| Парткод: | RL1-2282-000 |
| Деталь: | SHAFT, RIGHT DOOR LINK |
| Парткод: | FE2-2020-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-019 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | PLATE, READER MOUNTING |
| Парткод: | FL3-9360-000 |
| Деталь: | SPACER |
| Парткод: | FE2-0798-000 |
| Деталь: | CABLE, REG. SENSING CONNECTING |
| Парткод: | FM3-8634-000 |
| Деталь: | POWER SUPPLY CABLE ASSEMBLY |
| Парткод: | FM3-8183-000 |
| Деталь: | RAIL, CONTROL PANEL ASSY, LF. |
| Парткод: | FE2-0524-000 |
| Деталь: | RAIL, CONTROL PANEL ASSY, RT |
| Парткод: | FE2-0525-000 |
| Деталь: | COVER, RAIL |
| Парткод: | FE2-0526-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE2-0533-000 |
| Деталь: | PLATE, USB MOUNTING |
| Парткод: | FE2-0538-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK3-3135-000 |
| Деталь: | PLATE, READER FIXED |
| Парткод: | FC8-8105-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | HOLDER, PCB |
| Парткод: | FC8-8455-010 |
| Деталь: | LABEL, CAUTION |
| Парткод: | FU8-8257-000 |
| Деталь: | HOLDER, HDD |
| Парткод: | FC8-8643-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FC9-8619-000 |
| Деталь: | PLATE, READER JOINT |
| Парткод: | FE2-0314-000 |
| Деталь: | HDD, MK1676GSX |
| Парткод: | FK3-2219-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK2-9200-000 |
| Деталь: | CABLE, SATA POWER SUPPLY |
| Парткод: | FK2-9239-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-0863-000 |
| Деталь: | CABLE, STANDARD SATA POWER |
| Парткод: | FK2-9248-000 |
| Деталь: | TPM PCB ASSEMBLY |
| Парткод: | FM4-0783-000 |
| Деталь: | SCREW, MACH. PAN HEAD, M3X4 |
| Парткод: | XA9-1979-000 |
| Деталь: | DAMPER, CUSHION |
| Парткод: | XH9-0149-000 |
| Деталь: | CONTROLLER BOX ASSEMBLY |
| Парткод: | NPN |
| Деталь: | COVER, MAIN SWITCH |
| Парткод: | FC8-4000-000 |
| Деталь: | PLATE, 2ND DELIV. TRAY SUPPORT |
| Парткод: | FC8-5363-000 |
| Деталь: | MOUNT, SWITCH COVER |
| Парткод: | FC8-5378-000 |
| Деталь: | DOOR ASSEMBLY, RIGHT LOWER |
| Парткод: | FM3-8150-000 |
| Деталь: | COVER, RIGHT REAR SUB |
| Парткод: | FC8-8444-000 |
| Деталь: | COVER, INNER SUB, 1 |
| Парткод: | FC8-8186-000 |
| Деталь: | COVER, 1ST PAPER DELIVERY |
| Парткод: | FC8-8187-000 |
| Деталь: | TRAY, 1ST PAPER DELIVERY |
| Парткод: | FE2-0330-000 |
| Деталь: | COVER, RIGHT LOWER SUB, 2 |
| Парткод: | FC8-8190-000 |
| Деталь: | COVER, RIGHT LOWER SUB, 1 |
| Парткод: | FC8-8191-000 |
| Деталь: | COVER, REAR UPPER, 1 |
| Парткод: | FC8-8192-010 |
| Деталь: | COVER, INNER REAR, 2 |
| Парткод: | FC8-8193-010 |
| Деталь: | COVER, REAR |
| Парткод: | FC8-8196-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FC9-7297-000 |
| Деталь: | COVER, LEFT LOWER |
| Парткод: | FC8-8198-000 |
| Деталь: | COVER, GRIP |
| Парткод: | FC8-8201-000 |
| Деталь: | ARM, FRONT COVER, B |
| Парткод: | FC8-8203-000 |
| Деталь: | MOUNT, STOPPER ARM |
| Парткод: | FC8-8204-000 |
| Деталь: | HOOK, COVER, FRONT |
| Парткод: | FC8-8205-000 |
| Деталь: | COVER, INNER REAR, 1 |
| Парткод: | FC8-8207-010 |
| Деталь: | COVER, RIGHT FRONT SUB |
| Парткод: | FC8-8443-000 |
| Деталь: | COVER, REAR UPPER, 3 |
| Парткод: | FC8-8286-000 |
| Деталь: | COVER, INNER SUB, 2 |
| Парткод: | FC8-8290-000 |
| Деталь: | COVER, REAR RIGHT, SMALL |
| Парткод: | FE2-0329-000 |
| Деталь: | PLATE, FRONT DOOR FIXED |
| Парткод: | FC8-8512-000 |
| Деталь: | PLATE, STATIC CHARGE, LEFT |
| Парткод: | FC8-8638-000 |
| Деталь: | PLATE, STATIC CHARGE, RIGHT |
| Парткод: | FC8-8637-000 |
| Деталь: | COVER, CONNECTOR, 1 |
| Парткод: | FC8-8344-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FC8-8346-000 |
| Деталь: | COVER, HARD DISK DRIVE |
| Парткод: | FC8-8359-000 |
| Деталь: | COVER, INNER BOTTOM |
| Парткод: | FC8-8445-000 |
| Деталь: | ROLLER, BOTTLE TRAY |
| Парткод: | FC8-4649-000 |
| Деталь: | GUIDE, REVERSE BACK END |
| Парткод: | FC9-8612-000 |
| Деталь: | COVER, 2ND PAPER DELIVERY |
| Парткод: | FC8-8543-000 |
| Деталь: | COVER, LEFT FRONT |
| Парткод: | FE2-0541-000 |
| Деталь: | LABEL, TONER MODEL |
| Парткод: | FC8-8622-000 |
| Деталь: | LABEL, TONER MODEL |
| Парткод: | FC8-8623-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2759-000 |
| Деталь: | COVER, LEFT FRONT, UPPER |
| Парткод: | FE2-0542-000 |
| Деталь: | COVER, RIGHT LOWER SUB, 3 |
| Парткод: | FC8-8617-000 |
| Деталь: | STOPPER, RAIL |
| Парткод: | FE2-0531-000 |
| Деталь: | LABEL, MAIN POWER SUPPLY |
| Парткод: | FC9-7863-000 |
| Деталь: | LABEL, MAIN POWER SUPPLY |
| Парткод: | FC9-7862-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1035-000 |
| Деталь: | COVER, SLOT |
| Парткод: | FC8-8645-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FC0-2633-000 |
| Деталь: | EMBLEM |
| Парткод: | FL3-1185-000 |
| Деталь: | FRONT UPPER COVER ASSEMBLY |
| Парткод: | FM3-8077-000 |
| Деталь: | FRONT DOOR ASSEMBLY |
| Парткод: | FM3-8078-000 |
| Деталь: | LEFT REAR COVER ASSEMBLY |
| Парткод: | FM3-8079-010 |
| Деталь: | LABEL, LASER CAUTION |
| Парткод: | FC0-2901-000 |
| Деталь: | LABEL, GROUNDING CAUTION |
| Парткод: | FU7-8521-000 |
| Деталь: | RIGHT UPPER SUB COVER ASSEMBLY |
| Парткод: | FM3-8083-000 |
| Деталь: | LABEL, HARD DISK DRIVE CAUTION |
| Парткод: | FU7-8471-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FS7-2788-000 |
| Деталь: | HINGE, RIGHT DOOR, FRONT |
| Парткод: | FC8-8228-000 |
| Деталь: | HOLDER, M.P. STOPPER |
| Парткод: | FC8-8240-000 |
| Деталь: | COVER, CASSETTE RIGHT UPPER, 1 |
| Парткод: | FC8-8515-000 |
| Деталь: | COVER, CASSETTE RIGHT UPPER, 2 |
| Парткод: | FC8-8516-000 |
| Деталь: | COVER, WASTE TONER |
| Парткод: | FC8-8341-000 |
| Деталь: | SHEET, GLASS CLEANING |
| Парткод: | FC8-8634-000 |
| Деталь: | PAD, GLASS CLEANING |
| Парткод: | FC8-8635-000 |
| Деталь: | GLASS CLEANING ARM ASSEMBLY |
| Парткод: | FM3-8260-000 |
| Деталь: | HOOK, RIGHT DOOR |
| Парткод: | FC5-0631-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FC8-3782-000 |
| Деталь: | STOPPER, DOOR, RIGHT LOWER |
| Парткод: | FC8-5164-000 |
| Деталь: | HANDLE, DOOR |
| Парткод: | FC8-8172-000 |
| Деталь: | COVER, ENV. HEATER SWITCH |
| Парткод: | FC8-4137-000 |
| Деталь: | COVER, RIGHT UPPER |
| Парткод: | FC8-8291-000 |
| Деталь: | COVER, REVERSE BLANKING |
| Парткод: | FC8-8544-000 |
| Деталь: | COVER, REAR UPPER, 2 |
| Парткод: | FC8-8631-000 |
| Деталь: | SHEET, EXTRACTION ROLLER |
| Парткод: | FE3-3788-000 |
| Деталь: | SHEET, RIGHT DOOR, LOWER |
| Парткод: | FE3-4452-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | SCREW, COIN LOCK |
| Парткод: | FC0-9272-000 |
| Деталь: | WASHER |
| Парткод: | FC2-2121-000 |
| Деталь: | COVER, PLUG |
| Парткод: | FE2-0323-000 |
| Деталь: | CORD, POWER |
| Парткод: | FK2-8107-000 |
| Деталь: | CORD, POWER SUPPLY 230V |
| Парткод: | FK2-9571-000 |
| Деталь: | CORD, POWER |
| Парткод: | FK2-0515-000 |
| Деталь: | POWER CORD TERMINAL ASSY |
| Парткод: | FM0-1682-000 |
| Деталь: | LABEL, MEMORY CAUTION |
| Парткод: | FC0-5049-000 |
| Деталь: | IC, MB87L8650, GATE ARRAY |
| Парткод: | FK2-3218-000 |
| Деталь: | IC, R8A03018ABG U200, ASIC |
| Парткод: | FK2-8988-000 |
| Деталь: | IC, T6TH5EFG-0002(0), STANDARD |
| Парткод: | FK2-7852-000 |
| Деталь: | IC, MB87S1801 |
| Парткод: | FK2-8321-000 |
| Деталь: | IC, MB8AA4220, STANDARD |
| Парткод: | FK3-0865-000 |
| Деталь: | IC, CLOCK GENERATOR, HYBRID |
| Парткод: | FK3-1386-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY, 2 |
| Парткод: | FM0-2667-000 |
| Деталь: | GUIDE, PAPER FEED |
| Парткод: | FC8-8185-010 |
| Деталь: | FLAG, PAPER SENSOR |
| Парткод: | FE2-0616-000 |
| Деталь: | FLAG, PAPER SENSOR |
| Парткод: | FC8-8233-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FE2-0617-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | RC2-6598-000 |
| Деталь: | CASSETTE RAIL ASSY, LEFT |
| Парткод: | FM0-1641-000 |
| Деталь: | CASSETTE RAIL ASSY, LEFT |
| Парткод: | FM3-8025-000 |
| Деталь: | PAPER SENSOR ASSEMBLY |
| Парткод: | FM0-1642-000 |
| Деталь: | PHOTO SENSOR ASSEMBLY |
| Парткод: | FM3-8035-000 |
| Деталь: | CASSETTE RAIL ASSY, RIGHT |
| Парткод: | FM0-1643-000 |
| Деталь: | CASSETTE RAIL ASSY, RIGHT |
| Парткод: | FM3-8026-010 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | FM0-1657-000 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | FM4-8108-000 |
| Цена: | 1 700 ₽ |
| Деталь: | CABLE,PAPER PICK-UP CONNECTING |
| Парткод: | FM0-1659-000 |
| Деталь: | REMNANT DETECT ASSEMBLY |
| Парткод: | FM0-1669-000 |
| Деталь: | CASSETTE RAIL ASSEMBLY, RIGHT |
| Парткод: | FM3-8149-000 |
| Деталь: | PAPER SENSOR PCB ASSEMBLY |
| Парткод: | FM3-8607-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2758-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | FOOT, RUBBER |
| Парткод: | XH9-0136-000 |
| Деталь: | INTERNAL COMPONENTS 7 |
| Парткод: | NPN |
| Деталь: | FIXING MOTOR ASSEMBLY |
| Парткод: | RM1-6074-000 |
| Деталь: | CABLE, DRAWER |
| Парткод: | RM1-6857-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | FIXING DRIVE ASSY |
| Парткод: | FM0-1158-010 |
| Деталь: | FLAG, 2ND DELIVERY SENSOR |
| Парткод: | FC5-0996-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-0997-000 |
| Деталь: | FLAG, DUPLEX ENTRANCE SENSOR |
| Парткод: | FC5-1005-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-1006-000 |
| Деталь: | FLAG, 3RD DELIVERY SENSOR |
| Парткод: | FC5-1010-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC0-0636-000 |
| Деталь: | GUIDE, 3RD DELIVERY |
| Парткод: | FC8-8293-000 |
| Деталь: | HANDLE, PAPER DELIVERY DOOR |
| Парткод: | FC8-8297-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-8298-000 |
| Деталь: | GUIDE, DUPLEX ENTRANCE, 1 |
| Парткод: | FC8-8300-000 |
| Деталь: | GUIDE, 3RD DELIVERY, UPPER |
| Парткод: | FC8-8301-000 |
| Деталь: | GUIDE, REVERSE ENTRANCE |
| Парткод: | FC8-8304-000 |
| Деталь: | GUIDE, DUPLEX ENTRANCE, 2 |
| Парткод: | FC8-8309-000 |
| Деталь: | ROLLER, 2ND PAPER DELIVERY |
| Парткод: | FC8-8311-000 |
| Деталь: | COVER, 2ND DELIVERY GEAR |
| Парткод: | FC8-8331-000 |
| Деталь: | COVER, 3RD DELIVERY GEAR |
| Парткод: | FC8-8332-000 |
| Деталь: | SUPPORT, 2ND DELIVERY GEAR |
| Парткод: | FC8-8338-000 |
| Деталь: | SUPPORT, 3RD DELIVERY GEAR |
| Парткод: | FC8-8339-000 |
| Деталь: | GUIDE, ENTRANCE, 2 |
| Парткод: | FC8-8340-010 |
| Деталь: | GUIDE, SHAFT |
| Парткод: | FC8-8408-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-8410-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-8411-000 |
| Деталь: | COVER, 3RD DELIVERY ROLLER |
| Парткод: | FC8-8503-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC8-8591-000 |
| Деталь: | SHEET, PAPER DELIVERY |
| Парткод: | FC9-8580-000 |
| Деталь: | GUIDE, ENTRANCE, 1 |
| Парткод: | FL3-0641-000 |
| Деталь: | PAPER DELIVERY ROLLER ASSEMBLY |
| Парткод: | FM3-8053-000 |
| Деталь: | 3RD DELIVERY FLAPPER ASSY |
| Парткод: | FM3-8054-000 |
| Деталь: | 2ND FLAPPER SOLENOID ASSY |
| Парткод: | FM3-8056-000 |
| Деталь: | 3RD FLAPPER SOLENOID ASSY |
| Парткод: | FM3-8057-000 |
| Деталь: | ROLLER, REFORM |
| Парткод: | FC9-8621-000 |
| Деталь: | ROLLER, 3RD PAPER DELIVERY |
| Парткод: | FC8-8294-000 |
| Деталь: | 2ND UPPER GUIDE ASSEMBLY |
| Парткод: | FM3-8060-000 |
| Деталь: | PAPER DELIVERY FLAPPER ASSY |
| Парткод: | FM3-8062-000 |
| Деталь: | TOGGLE COVER ASSEMBLY |
| Парткод: | FM3-8063-000 |
| Деталь: | COLLAR, REGISTRATION MULTI |
| Парткод: | FS5-6945-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FS7-2859-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1453-000 |
| Деталь: | BUSHING, POLYACETAR |
| Парткод: | FU5-1469-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU6-0076-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2772-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2783-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0396-000 |
| Деталь: | GEAR, 20T |
| Парткод: | FU8-0397-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0403-000 |
| Деталь: | ROLLER, DUPLEXING PAPER FEED |
| Парткод: | RC2-7271-000 |
| Деталь: | BUSHING |
| Парткод: | RS5-1567-000 |
| Деталь: | GEAR, 28T |
| Парткод: | RU6-0852-000 |
| Деталь: | GEAR, 17T |
| Парткод: | RU6-0855-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | IC,PHOTO-INTERRUPTER,LG248NL1A |
| Парткод: | WG8-5783-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FC9-8582-000 |
| Деталь: | SHEET, ENTRANCE GUIDE, 1 |
| Парткод: | FC8-8310-000 |
| Деталь: | GUIDE, 2ND DELIVERY ENTRANCE |
| Парткод: | FC0-0598-010 |
| Деталь: | STOPPER, GUIDE, UPPER |
| Парткод: | FC9-8645-000 |
| Деталь: | STOPPER, GUIDE, LOWER |
| Парткод: | FC9-8646-000 |
| Деталь: | SHEET, COMPENSATION, F |
| Парткод: | FL3-0777-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC8-8590-010 |
| Деталь: | SHEET, COMPENSATION, R |
| Парткод: | FL3-0778-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0239-000 |
| Деталь: | 2ND/3RD DELIVERY GUIDE ASSY |
| Парткод: | FM3-8052-010 |
| Деталь: | PULLEY, 34T |
| Парткод: | FC6-5022-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK2-7586-000 |
| Деталь: | GEAR, 80T/16T |
| Парткод: | FU3-0285-000 |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1604-940 |
| Деталь: | PAPER PICK-UP DRIVE ASSEMBLY |
| Парткод: | FM3-8151-000 |
| Деталь: | COVER, HINGE BLANKING |
| Парткод: | FC9-6192-010 |
| Деталь: | SCREW, STEPPED, M5 |
| Парткод: | FU5-9168-000 |
| Деталь: | SCREW, FIXED, M4 |
| Парткод: | FU5-9167-000 |
| Деталь: | SHEET, BLANKING |
| Парткод: | FC9-6193-000 |
| Деталь: | LABEL, FINGER NIP CAUTION |
| Парткод: | FU7-8165-000 |
| Деталь: | LABEL, FINGER NIP CAUTION |
| Парткод: | FU7-8166-000 |
| Деталь: | LABEL, FINGER NIP CAUTION |
| Парткод: | FU7-8167-000 |
| Деталь: | LABEL, FINGER NIP CAUTION |
| Парткод: | FU7-8168-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FU7-8225-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FU7-8226-000 |
| Деталь: | ADF MOUNTING ASSEMBLY |
| Парткод: | NPN |
| Деталь: | SHAFT |
| Парткод: | FC0-0618-000 |
| Деталь: | LINK, HANDLE |
| Парткод: | FC0-0619-000 |
| Деталь: | LEVER, LINK |
| Парткод: | FC0-0620-000 |
| Деталь: | LATCH, FRONT |
| Парткод: | FC0-0622-000 |
| Деталь: | LATCH, REAR |
| Парткод: | FC0-0623-000 |
| Деталь: | HOLDER, LATCH, FRONT |
| Парткод: | FC0-0624-000 |
| Деталь: | HOLDER, LATCH, REAR |
| Парткод: | FC0-0625-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | HOOK |
| Парткод: | FC0-0627-000 |
| Деталь: | LEVER, LOCK |
| Парткод: | FC0-0628-000 |
| Деталь: | SHEET, BASE GUIDE |
| Парткод: | FC0-0629-000 |
| Деталь: | PIN, PRESSURE |
| Парткод: | FC0-0630-000 |
| Деталь: | STOPPER, PAPER DELIVERY GUIDE |
| Парткод: | FC8-8226-000 |
| Деталь: | STOPPER |
| Парткод: | FC8-8241-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FC8-8348-000 |
| Деталь: | LABEL, LASER CAUTION |
| Парткод: | FC8-8355-000 |
| Деталь: | FLAG, OPEN/CLOSE SENSOR |
| Парткод: | FC8-8356-000 |
| Деталь: | PIN, POSITIONING |
| Парткод: | FC8-8413-000 |
| Деталь: | ROLLER, REEL |
| Парткод: | FC8-8492-000 |
| Деталь: | SHEET, NOISE-PROOF |
| Парткод: | FC8-8524-000 |
| Деталь: | SHAFT, HANDLE FIXED |
| Парткод: | FC8-8538-000 |
| Деталь: | HANDLE |
| Парткод: | FC8-8539-000 |
| Деталь: | COVER, PAPER PICK-UP ROLLER |
| Парткод: | FE2-1999-000 |
| Деталь: | MULTI PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-8038-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2768-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2782-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2792-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2797-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2798-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2799-000 |
| Деталь: | SPRING, POWER DISPATCHING |
| Парткод: | FU7-2800-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU7-2801-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2803-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2804-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2805-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2814-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2819-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2820-000 |
| Деталь: | CLAMP, LEVER, REAR |
| Парткод: | FE2-2083-000 |
| Деталь: | STOPPER, PAPER PICK-UP SHAFT |
| Парткод: | FE2-2088-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2519-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE2-2025-000 |
| Деталь: | COVER, GEAR |
| Парткод: | FE2-1989-000 |
| Деталь: | HOOK, SPRING, LEFT |
| Парткод: | FE2-2047-000 |
| Деталь: | PIN, SPRING HOOK |
| Парткод: | FE2-2048-000 |
| Деталь: | HOOK, SPRING, RIGHT |
| Парткод: | FE2-2049-000 |
| Деталь: | LINK, M.P. HINGE |
| Парткод: | FE2-2050-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE2-1975-000 |
| Деталь: | CLIP |
| Парткод: | FE2-2110-000 |
| Деталь: | COVER, GROUNDING |
| Парткод: | FE2-1992-000 |
| Деталь: | ROLLER, DUPLEXING PAPER FEED |
| Парткод: | RC2-7271-000 |
| Деталь: | ROLLER, REG. |
| Парткод: | RC2-7280-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2521-000 |
| Деталь: | HOOK, FRONT |
| Парткод: | FE2-2115-000 |
| Деталь: | HOOK, REAR |
| Парткод: | FE2-2116-000 |
| Деталь: | GUIDE, CONDUCTIVE |
| Парткод: | FE2-2117-000 |
| Деталь: | HOOK |
| Парткод: | FE2-2118-000 |
| Деталь: | COVER, CABLE |
| Парткод: | FE2-1996-000 |
| Деталь: | SECONDARY TRANSFER GUIDE ASSY |
| Парткод: | RM1-6041-000 |
| Деталь: | M.P. PAPER PICK-UP GEAR ASSY |
| Парткод: | RM1-6049-000 |
| Деталь: | M.P. PAPER PICK-UP SHAFT ASSY |
| Парткод: | RM1-6050-000 |
| Деталь: | MP LIFTER PLATE ASSY |
| Парткод: | RM1-6124-000 |
| Деталь: | DUPLEXING GEAR COVER ASSEMBLY |
| Парткод: | RM1-6151-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | RL1-2244-000 |
| Цена: | 2 900 ₽ |
| Деталь: | MULTI-PURPOSE SEP. PAD KIT |
| Парткод: | RM1-6163-040 |
| Деталь: | 2ND TRANSFER ROLLER ASSY |
| Парткод: | RM1-7928-000 |
| Деталь: | SOLENOID |
| Парткод: | RM1-6790-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1110-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1578-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1579-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1580-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1581-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU0-0198-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU0-0183-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2526-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2693-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2516-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU9-2530-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2528-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-007 |
| Деталь: | LABEL, FEED SIZE |
| Парткод: | FE2-1822-000 |
| Деталь: | LABEL, FEED SIZE |
| Парткод: | FE2-1823-000 |
| Деталь: | LABEL, FEED SIZE |
| Парткод: | FE2-1824-000 |
| Деталь: | LABEL, PAPER SET INSTRUCTION |
| Парткод: | FC9-8584-000 |
| Деталь: | LABEL, PAPER SET INSTRUCTION |
| Парткод: | FC9-8585-000 |
| Деталь: | GUIDE, RIGHT DOOR, UPPER |
| Парткод: | FC8-8235-000 |
| Деталь: | GUIDE, PAPER DELIVERY, 1 |
| Парткод: | FC8-8251-000 |
| Деталь: | GUIDE, PAPER DELIVERY, 2 |
| Парткод: | FC8-8252-000 |
| Деталь: | HINGE, RIGHT DOOR, REAR |
| Парткод: | FC8-8353-000 |
| Деталь: | INNER GUIDE ASSEMBLY |
| Парткод: | FM3-8039-000 |
| Деталь: | PLATE, POWER DISPATCHING |
| Парткод: | FE2-1976-000 |
| Деталь: | RIGHT DOOR ASSEMBLY |
| Парткод: | FM3-8036-000 |
| Деталь: | PLATE, FREE STOP |
| Парткод: | FC8-2670-000 |
| Деталь: | WINDOW, CST FR. COVER IND. |
| Парткод: | FC8-4967-000 |
| Деталь: | BUTTON, PUSHING |
| Парткод: | FC8-4985-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FC8-4990-000 |
| Деталь: | COVER, CASSETTE FRONT |
| Парткод: | FC8-8181-010 |
| Деталь: | RING, BUTTON |
| Парткод: | FC8-8182-000 |
| Деталь: | COVER, SIZEPLATE |
| Парткод: | FC9-4042-000 |
| Деталь: | SHAFT, SUPPORT |
| Парткод: | FE2-0565-000 |
| Деталь: | PLATE, PAPER SIDE END AUX. |
| Парткод: | FE2-0570-000 |
| Деталь: | RACK, SIDE |
| Парткод: | FE2-0574-000 |
| Деталь: | PLATE, BACK END LIMIT |
| Парткод: | FE2-0580-000 |
| Деталь: | RACK, LINK |
| Парткод: | FE2-0581-000 |
| Деталь: | CAM, WIDTH DETECT |
| Парткод: | FE2-0582-000 |
| Деталь: | CAM, BACK END DETECT |
| Парткод: | FE2-0583-000 |
| Деталь: | COVER, WIDTH DETECT |
| Парткод: | FE2-0584-000 |
| Деталь: | ROLLER, CASSETTE SWING |
| Парткод: | FE2-0599-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE2-0619-000 |
| Деталь: | COVER, ROLLER, RIGHT |
| Парткод: | FE2-0620-000 |
| Деталь: | COVER, ROLLER, LEFT |
| Парткод: | FE2-0621-000 |
| Деталь: | GEAR, 30T |
| Парткод: | FE2-0623-000 |
| Деталь: | ARM, BACK END DETECT |
| Парткод: | FE2-1683-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE2-1684-000 |
| Деталь: | LABEL, SIZE INDEX, SIDE, LARGE |
| Парткод: | FE3-3943-000 |
| Деталь: | LABEL, SIZE INDEX, END |
| Парткод: | FE3-3944-000 |
| Деталь: | LABEL, SIZE INDEX, END |
| Парткод: | FE3-3945-000 |
| Деталь: | LABEL, PAPER PICK-UP OPERATION |
| Парткод: | FE2-1812-000 |
| Деталь: | PLATE, CENTER |
| Парткод: | FL3-7814-000 |
| Деталь: | SIDE END PLATE ASSEMBLY, FRONT |
| Парткод: | FM0-1645-000 |
| Деталь: | SIDE END PLATE ASSEMBLY, REAR |
| Парткод: | FM0-1646-000 |
| Деталь: | BACK END LIMIT PLATE ASSEMBLY |
| Парткод: | FM0-1647-000 |
| Деталь: | BUTTON LINK ASSEMBLY |
| Парткод: | FM0-1648-000 |
| Деталь: | GEAR, 20T/12T |
| Парткод: | FU0-0059-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2441-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2442-000 |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-1523-000 |
| Деталь: | SHEET, CUTTING WASTE |
| Парткод: | FC0-0394-000 |
| Деталь: | CASSETTE ASSEMBLY |
| Парткод: | FM0-1644-000 |
| Деталь: | FIXING ASSEMBLY |
| Парткод: | FM1-B290-000 |
| Деталь: | FIXING ASSEMBLY |
| Парткод: | FM4-6228-000 |
| Деталь: | GUIDE, FIXING DELIVERY, UPPER |
| Парткод: | FM4-7712-000 |
| Деталь: | GUIDE, FIXING DELIVERY, UPPER |
| Парткод: | FM4-7713-000 |
| Деталь: | FIXING ASSEMBLY |
| Парткод: | NPN |
| Деталь: | FLANGE, BELT |
| Парткод: | FC5-4353-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | GUIDE, PLATEN, 2 |
| Парткод: | FE2-1916-000 |
| Деталь: | FLAPPER, REVERSE |
| Парткод: | FL2-9949-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FC8-6372-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FC8-6377-000 |
| Деталь: | DUCT, HARNESS |
| Парткод: | FC8-6378-020 |
| Деталь: | FLANGE, PULLEY |
| Парткод: | FC8-6379-000 |
| Деталь: | CLIP |
| Парткод: | FC8-6380-000 |
| Деталь: | ROLLER, BELT TENSION |
| Парткод: | FC8-6382-000 |
| Деталь: | JOINT, DELIVERY GEAR |
| Парткод: | FC8-6385-000 |
| Деталь: | DIAL, JAM |
| Парткод: | FC0-9097-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6395-010 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FC8-6396-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FC0-4619-000 |
| Деталь: | JOINT, READ PULLEY |
| Парткод: | FC8-6418-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FC8-6421-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK3-1613-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK3-2679-000 |
| Деталь: | FLAG, REGISTRATION SENSOR |
| Парткод: | FL2-9937-000 |
| Деталь: | GEAR, 48T/62T |
| Парткод: | FU9-0937-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6411-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU9-0931-000 |
| Деталь: | JOINT, REGISTRATION |
| Парткод: | FC8-6384-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC8-6412-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0932-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE2-1917-000 |
| Деталь: | ARM, PLATEN, FRONT |
| Парткод: | FC8-6373-000 |
| Деталь: | ARM, PLATEN, REAR |
| Парткод: | FE2-1918-000 |
| Деталь: | SPACER, READ, FRONT |
| Парткод: | FC8-6375-000 |
| Деталь: | SPACER, READ, REAR |
| Парткод: | FC8-6376-000 |
| Деталь: | ROLLER, WHITE |
| Парткод: | FC0-9124-000 |
| Деталь: | GUIDE, PLATEN, 1 |
| Парткод: | FL2-9939-000 |
| Деталь: | LINK, SOLENOID |
| Парткод: | FC8-6381-000 |
| Деталь: | DAMPER, REV. GUIDE RETAINING |
| Парткод: | FC8-6403-000 |
| Деталь: | SOLENOID |
| Парткод: | FK3-2682-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU9-0933-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | GUIDE, SEPARATION REVERSE |
| Парткод: | FM0-1223-000 |
| Деталь: | PAD, SEPARATION |
| Парткод: | FL3-5538-010 |
| Цена: | 1 400 ₽ |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2657-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1607-640 |
| Деталь: | BEARING, BALL |
| Парткод: | XG9-0820-000 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-0702-000 |
| Деталь: | SCREW,RS,M3X6.5 |
| Парткод: | XA9-1164-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1626-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1088-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1089-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2659-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2660-000 |
| Деталь: | PULLEY, 27T/GEAR, 22T |
| Парткод: | FU9-0934-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0935-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU9-0936-000 |
| Деталь: | GEAR PULLEY, 36T/54T/28T |
| Парткод: | FU8-0309-000 |
| Деталь: | PULLEY, 36T |
| Парткод: | FU8-0310-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0312-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0313-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU8-0314-000 |
| Деталь: | GEAR, 39T |
| Парткод: | FU8-0315-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU8-0316-000 |
| Деталь: | GEAR, 32T |
| Парткод: | FU8-0317-000 |
| Деталь: | SHEET, CLEANING |
| Парткод: | FC8-6356-000 |
| Деталь: | SHEET, CLEANING, SMALL |
| Парткод: | FC8-6357-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE2-1919-000 |
| Деталь: | BUSHING |
| Парткод: | FS6-1140-000 |
| Деталь: | BUSHING, CONDUCTIVE |
| Парткод: | RS5-1101-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-122 |
| Деталь: | FEED ASSEMBLY |
| Парткод: | FM0-1220-000 |
| Деталь: | IC,TC00GO2EFG-1031,GATE ARRAY |
| Парткод: | FK2-1773-000 |
| Деталь: | ADF PCB ASSEMBLY |
| Парткод: | FM0-1188-000 |
| Деталь: | TAPE, GROUNDING |
| Парткод: | FC0-3651-000 |
| Деталь: | ROLLER, RAIL |
| Парткод: | FC8-4999-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FC8-8174-000 |
| Деталь: | LEVER, SENSOR |
| Парткод: | FC8-8176-000 |
| Деталь: | HOLDER, SWITCH |
| Парткод: | FC8-8177-000 |
| Деталь: | SCREW W/WASHER, M3X6 |
| Парткод: | XA9-1016-000 |
| Деталь: | MOUNT, CASSETTE POSITIONING |
| Парткод: | FC8-8237-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FC8-8628-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | AUTO SIZE DETECT ASSEMBLY |
| Парткод: | FM3-5933-000 |
| Деталь: | CABLE, MOTOR CONNECTING |
| Парткод: | FM3-7843-000 |
| Деталь: | SWITCH CABLE UNIT, OPEN/CLOSE |
| Парткод: | FM3-8647-000 |
| Деталь: | CASSETTE HEATER ASSEMBLY |
| Парткод: | FM0-4833-000 |
| Деталь: | LABEL, HIGH TMP. CAUTION |
| Парткод: | FU6-8647-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-011 |
| Деталь: | GUIDE, RIGHT RAIL, FRONT |
| Парткод: | FC8-8097-000 |
| Деталь: | GUIDE, RIGHT RAIL, REAR |
| Парткод: | FC8-8099-000 |
| Деталь: | COVER, CASSETTE FRONT |
| Парткод: | FC8-8180-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FC9-8588-000 |
| Деталь: | INTERNAL COMPONENTS 6 |
| Парткод: | NPN |
| Деталь: | DC MOTOR ASSEMBLY |
| Парткод: | FM0-1917-000 |
| Деталь: | SIZE DETECT SWITCH UNIT |
| Парткод: | RM1-5058-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-004 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-017 |
| Деталь: | LIFTER DRIVE ASSEMBLY |
| Парткод: | FM0-1638-000 |
Коды ошибок
E001-0001
E001-0002
E001-0003
E001-0004
E001-0005
E001-0006
E001-0007
E001-0008
E002-0006
E003-0001
E003-0002
E003-0003
E003-0004
E003-0005
E003-0006
E003-0007
E003-0008
E004-0001
E004-0005
E004-0006
E009-0000
E010-0001
E010-0002
E010-0003
E012-0001
E012-0002
E012-0003
E014-0001
E014-0002
E014-0003
E020-0020
E020-0030
E020-0040
E020-0041
E020-0050
E020-0060
E020-0070
E020-0090
E020-0091
E020-00B0
E020-00B1
E020-0120
E020-0130
E020-0140
E020-0141
E020-0150
E020-0160
E020-0170
E020-0190
E020-0191
E020-01B0
E020-01B1
E020-0220
E020-0230
E020-0240
E020-0241
E020-0250
E020-0260
E020-0290
E020-0291
E020-02B0
E020-02B1
E020-0320
E020-0330
E020-0340
E020-0341
E020-0350
E020-0360
E020-0390
E020-0391
E020-03B0
E020-03B1
E020-1050
E020-1060
E020-1150
E020-1160
E020-1250
E020-1260
E020-1350
E020-1360
E021-0001
E021-0003
E021-0020
E021-0120
E021-0220
E021-0320
E022-0000
E025-0000
E025-0010
E025-0020
E025-0030
E025-0100
E025-0110
E025-0120
E025-0130
E025-0200
E025-0210
E025-0220
E025-0230
E025-0300
E025-0310
E025-0320
E025-0330
E032-0001
E040-0002
E065-0000
E065-0001
E065-0002
E065-0003
E067-0001
E067-0002
E067-0003
E069-0001
E069-0002
E074-0000
E074-FFFF
E100-0001
E100-0002
E100-0003
E110-0001
E110-0002
E110-0003
E194-0000
E194-0001
E194-FFFF
E196-0001
E196-0002
E196-0003
E196-1B00
E196-1B01
E196-1B02
E196-1B03
E196-1B04
E196-1BFF
E197-0000
E197-0050
E202-0001
E202-0002
E225-0001
E227-0001
E227-0002
E227-0003
E227-0004
E240-0000
E240-0001
E240-0002
E240-0003
E240-0004
E240-0005
E240-0006
E240-0007
E246
E247
E248-0001
E248-0002
E248-0003
E270-0001
E270-0002
E280-0001
E280-0002
E280-0003
E280-0004
E301-0001
E301-0002
E302-0001
E302-0002
E315-0007
E315-000d
E315-000e
E315-000f
E315-0027
E315-0035
E315-0100
E315-0500
E315-0501
E315-0510
E315-0511
E315-0520
E315-0521
E315-0530
E315-0531
E315-0540
E315-0541
E315-0550
E315-0551
E350
E351-0000
E354
E355
E400-0001
E400-0002
E400-0003
E413-0001
E413-0002
E500-0000
E503-0002
E505-0001
E514-8001
E514-8002
E517-0001
E519-0002
E519-8001
E520-0001
E520-0002
E530-8001
E530-8002
E531-8001
E531-8002
E532-0001
E532-0002
E532-8001
E532-8002
E535-8001
E535-8002
E537-8001
E537-8002
E540-0001
E540-0005
E540-8001
E540-8002
E540-8003
E540-8004
E540-8005
E540-8006
E540-8007
E542-0001
E542-0005
E542-8001
E542-8002
E542-8003
E542-8004
E542-8005
E542-8006
E542-8007
E551-8001
E551-8002
E567-0001
E567-0002
E56F-
E56F-0001
E571-0001
E571-0002
E575-0001
E575-0002
E584-0002
E584-8001
E5F0-8001
E5F0-8002
E5F1-8001
E5F1-8002
E5F2-8001
E5F2-8002
E5F3-8001
E5F3-8002
E5F4-8001
E5F4-8002
E5F5-8001
E5F5-8002
E5F6-8001
E5F6-8002
E5F6-8003
E5F6-8004
E5F6-8005
E602
E604-0512
E604-1024
E604-1536
E611-0000
E613-0512
E613-1024
E613-1536
E614
E615-0001
E674-0001
E674-0004
E674-0008
E674-000C
E674-0010
E674-0011
E674-0030
E677-0003
E710-0001
E711-0001
E713-0001
E713-0002
E713-0003
E713-0004
E713-0005
E713-0006
E713-0007
E713-0008
E719-0001
E719-0002
E719-0003
E719-0004
E719-0011
E719-0012
E719-0031
E719-0032
E730-1001
E730-100A
E730-A006
E730-A007
E730-B013
E730-C000
E730-C001
E731-3000
E731-3001
E731-3002
E731-3015
E732-0001
E732-9999
E732-FFFF
E733-0000
E733-0001
E733-0005
E733-0006
E733-9999
E733-F000
E740-0002
E740-0003
E743-0000
E744
E746-0021
E746-0022
E746-0023
E746-0024
E746-0031
E746-0032
E746-0033
E746-0034
E746-0035
E747-1201
E748-2010
E748-2021
E748-2023
E748-2024
E748-9000
E749-0002
E749-0003
E749-0005
E749-0006
E750-0013
E753-0001
E804-0000
E806-0001
E807-0001
E808-0001
E808-0002
E880-0001
E996-0071
E996-0CA1
E996-0CA2
E996-0CA3
E996-0CF1
Описание
| Error code: | E001-0001 |
| Description: | Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control. |
| Causes: | The sub thermistor detected a temperature of higher than 290 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0002 |
| Description: | Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 1 has detected a high temperature (ASIC detection) |
| Causes: | The fixing film unit is faulty (i.e., the thermistor has a short circuit). The main power supply PCB is faulty. The DC controller PCB is faulty. Caution To clear the error, execute the following in service move: COPIER>FUNCTION>CLEAR>ERR. |
| Remedy: | Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E001-0003 |
| Description: | Abnormally high temperature rise of fixing unit (circuit trouble) When fixing sub-thermistor 2 has detected a high temperature (ASIC detection) |
| Remedy: | Check the connection of the connector in the thermistor wiring (wirepinching, disconnection). Replace the fixing unit. Replace the IH unit, halogen heater, fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E001-0004 |
| Description: | Abnormal high temperature in fixing |
| Causes: | The sub thermistor 2 detected a temperature exceeding a specified temperature |
| Remedy: | Replace the fixing assembly. Replace the DC controller PCB. |
| Error code: | E001-0005 |
| Description: | The fixing unit is overheating. At the end of initial rotation, the difference in temperature between the sub (end) thermistor and the main (non-contact) thermistor is 20°C or more for 100 msec. (A reversal in temperature (caused, for example, by a piece of residual paper) is detected.) |
| Remedy: | Check on remaining paper in the fixing unit, Replace the fixing unit To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR |
| Error code: | E001-0006 |
| Description: | Abnormality of the fixing unit A break in the non-contact thermistor film The status that A/D of the non-contact thermistor film is FFh continues for 500msec. |
| Remedy: | Check on connection of the thermistor, Replace the fixing unit To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR |
| Error code: | E001-0007 |
| Description: | Abnormality of the fixing unit A short circuit in the non-contact thermistor film The status that A/D of the non-contact thermistor film is 30h or less continues for 500msec. |
| Remedy: | Replace the fixing unit To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR |
| Error code: | E001-0008 |
| Description: | Abnormality of the fixing unit A break in the non-contact thermistor case The status that A/D of the non-contact thermistor case is FFh continues for 500msec. |
| Remedy: | Check on connection of the thermistor, Replace the fixing unit To recover from the error: In service mode COPIER>FUNCTION>CLEAR >ERR |
| Error code: | E002-0006 |
| Description: | Insufficient temperature rise of fixing unit When the fixing main thermistor fails to reach 170 deg C within the prescribed period of time after reaching 150 deg C during warm-up |
| Remedy: | Replace the fixing belt unit. Replace the fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E003-0001 |
| Description: | Abnormally low temperature (detected by sub thermistor) After the temperature detected by the sub thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The sub thermistor detected a temperature of lower than 80 degree C for more than 2 seconds when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0002 |
| Description: | Fixing unit low temperature trouble When the pressure main thermistor has detected a temperature below 50 deg C for the prescribed period of time after standby |
| Remedy: | Checking Disconnection of the Connector in the Thermistor Wiring. Replace the fixing belt unit. Replace the fixer and AC driver PCB. Replace the DC controller PCB 2 (MAISY). In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E003-0003 |
| Description: | Perssure belt abnormally low temperature. After went in standby, Pressure sub thermistor 1(THM3) detected less or equal to 50 degrees Celsius for specified time (250sec) |
| Remedy: | 1. Check if the detection temperature of the thermistor is risen in service mode. A. In case that either one of the thermistor detection temperature is risen A-1. Check the pressure sub thermistor 2 (to see if the location of the thermistor is inappropriate, the harness of the thermistor is disconnected, failure of the thermistor) -> replace the pressure sub thermistor or the pressure stay A-2. Faulty drawer connector -> clean the drawer connector or replace the fixing assembly B. In case that neither of them are not risen B-1. Check the connection of the AC driver connector (to see if the connector is physically removed or disconnected, or the cable is caught) B-2. Replace the AC driver unit B-3. Replace the DC controller PCB B-4. Replace the fixing assembly |
| Error code: | E003-0004 |
| Description: | Abnormal low temperature in fixing |
| Causes: | The sub thermistor 2 detected a temperature lower than a specified temperature. |
| Remedy: | Replace the fixing assembly. Replace the DC controller PCB. |
| Error code: | E003-0005 |
| Description: | Main Thermistor 2 low temperature detection at printing In the period from printing to last rotation, Main Thermistor 1 detected a temperature of 70 deg C or lower for more than 5 seconds. |
| Remedy: | Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Replace the Fixing Assembly 3. Replace the DC Controller PCB (UN09) NOTE: After performing the above remedy work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E003-0006 |
| Description: | Center Thermistor low temperature detection at printing In the period from printing to last rotation, Main Thermistor 2 detected a temperature of 80 deg C or lower for more than 1 second. |
| Remedy: | Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Replace the Fixing Assembly 3. Replace the DC Controller PCB (UN09) NOTE: After performing the above remedy work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E003-0007 |
| Description: | Edge Thermistor low temperature detection at printing In the period from printing to last rotation, Sub Thermistor 1 detected a temperature of 80 deg C or lower for more than 1 second. |
| Remedy: | Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Replace the Fixing Assembly 3. Replace the DC Controller PCB (UN09) NOTE: After performing the above remedy work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E003-0008 |
| Description: | Edge Thermistor low temperature detection at printing In the period from printing to last rotation, Sub Thermistor 2 detected a temperature of 80 deg C or lower for more than 1 second. |
| Remedy: | Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Replace the Fixing Assembly 3. Replace the DC Controller PCB (UN09) NOTE: After performing the above remedy work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E004-0001 |
| Description: | There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the outside heating roller heater. |
| Remedy: | Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR. |
| Error code: | E004-0005 |
| Description: | Fixing Relay fusion error |
| Causes: | At power ON or recovery from sleep mode, a zero cross signal was detected three times during the period of 100 ms after completion of CPU initialization. |
| Remedy: | 1. Check the harness/connector between the Fixing Assembly and the DC Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB. |
| Error code: | E004-0006 |
| Description: | There is an error in the fixing assembly protection circuit. There is an open circuit or poor contact in the main thermistor (THM1, THM2, THM3) or sub thermistor (TH4, THM5, THM6). The AC driver PCB or the DC controller PCB has a fault. There is an SSR error in the fixing sub heater or the fixing main heater |
| Remedy: | Check the main thermistor and the sub thermistor for an open circuit and poor contact; then, reset in service mode: COPIER>FUNCTION>CLEAR>ERR. |
| Error code: | E009-0000 |
| Description: | Error in engagement Unable to detect ON with the Fixing Pressure Sensor although 5 seconds have passed. |
| Remedy: | 1. Turn OFF and then ON the power. 2. Remove and then reinstall the Fixing Assembly. 3. Go through the following to move M21: COPIER > FUNCTION > PART-CHK > MTR. If the motor rotates properly: 4-1. Replace the Fixing Drive Assembly. 5-1. Replace the DC Controller PCB (UN1). If the motor does not work properly: 4-2. Identify and replace the faulty gear. 5-2. Replace the Motor. |
| Error code: | E010-0001 |
| Description: | Main motor error Lock of the motor fails to be detected 2 sec or more after the motor starts to operate. |
| Causes: | The main motor drive system has an excess load. The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check on connection of the connector, Replace the motor |
| Error code: | E010-0002 |
| Description: | Main motor error After rotation of the motor becomes stable, the motor lock fails (i.e., the motor becomes unstable) for 500msec or more. |
| Causes: | The main motor drive system has an excess load. The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check on connection of the connector, Replace the motor |
| Error code: | E010-0003 |
| Description: | The pedestal main motor (M19) is released. The motor is checked every 10 msec from 2000 msec after it is started to when it is stopped. However, detection is not made when the front cover/delivery assembly cover/face-down delivery unit is released or when there is a fault in the power supply system. |
| Causes: | The main motor drive system has an excess load. The pickup main motor (M2)/delivery main motor (M16)/pedestal main motor (M19) is faulty. The serial driver PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Possible cause is overload or rotation failure of the motor due to an electrical trouble 1. Check the Main Drive Unit (turn the unit by hand to see if it rotates) Replace the Main Drive Unit when the unit failed to rotate When the unit rotates 2. Check failure of the harness between the ITB Motor (M02/ J6027) and the DC Controller PCB (UN09/ J210W) (trapped cable, open circuit, connector disconnection) 3. Check conduction of the fuse (FU4) in the DC Controller PCB (UN09) When the fuse is not blown out 4-1. Replace the ITB Motor (M02) 5-1. Replace the DC Controller PCB (UN09) 6-1. Replace the Main Drive Unit When the fuse is blown out 4-2. Replace the DC Controller PCB (UN09) |
| Error code: | E012-0001 |
| Description: | Error in ITB motor activation. |
| Causes: | If the ITB motor speed detection signal comes off the specified cycle after it turned once to the specified cycle. Cause Failure in ITB motor, failure in DC controller PCB. |
| Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
| Error code: | E012-0002 |
| Description: | ITB motor or drum motor failure |
| Causes: | Yellow drum motor error (Failure in drum motor initial operation) The target speed was not reached within a specified time after startup of the motor |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly. |
| Error code: | E012-0003 |
| Description: | ITB motor or drum motor failure |
| Causes: | Yellow drum motor error (Failure in drum motor rotation) The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the drum motor (J515) and the DC controller PCB (J81). Replace the drum motor. Replace the main drive assembly |
| Error code: | E014-0001 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E014-0002 |
| Description: | Fixing motor error When the lock was disengaged after the motor was locked |
| Causes: | The belt motor (M15) is faulty. The belt motor drive system has an excess load. The drum drive AC generation PCB is faulty. The transfer drive AC generation PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Replace the drumITB moter. Replace the fixing moter.Replace the DCDC converterAi38VAj. Replace the fixing belt unit. |
| Error code: | E014-0003 |
| Description: | The encoder signal is not generated by the motor. |
| Causes: | The belt motor (M15) is faulty. The belt motor drive system has an excess load. The drum drive AC generation PCB is faulty. The transfer drive AC generation PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Possible cause is overload or rotation failure of the motor due to an electrical trouble 1. Check if the Fixing Assembly is installed. 2. Remove and reinstall the Fixing Assembly 3. Check the gear 4. Replace the Fixing Assembly 5. Check the harness/connector between the DC Controller PCB (UN09/ J210) and the Fixing Motor (M17). 6. Check conduction of FU1153 in the AC Driver PCB (UN14) =>Replace the AC Driver when the fuse is blown out 7. Replace the Fixing Motor (M17) 8. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0020 |
| Description: | Error in the developing assembly (toner fault: ATR error) Indicates that the patch level is lower than the lower limit of the target although setting it as the maximum when initializing Yellow ATR. |
| Remedy: | Clean the ATR sensor window. Check the mounting of the developing assembly. Check the ATR sensor open circuit. Replace the ATR sensor. |
| Error code: | E020-0030 |
| Description: | ATR Sensor (Y) error or toner supply error Error in detected TD ratio. The average of ATR reference value is the specified value or higher at the time of ATR Sensor (Y) initialization. |
| Remedy: | 1. Check if the Drum Unit (Y) is installed. 2. Check the Drum Unit Relay PCB (Y) (UN26) 3. Check the Drum Unit Memory PCB (Y) (UN30) 4. Check the harness/connector between the DC Controller PCB (UN09/ J25) and the Drum Unit Relay PCB (Y) (UN26). 5. Replace the Drum Unit (Y). 6. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0040 |
| Description: | ATR Sensor (Y) error or toner supply error Unable to adjust the control voltage at the time of ATR Sensor (Y) initialization. |
| Remedy: | 1. Check if the Drum Unit (Y) is installed. 2. Check the Drum Unit Relay PCB (Y) (UN26) 3. Check the Drum Unit Memory PCB (Y) (UN30) 4. Check the harness/connector between the DC Controller PCB (UN09/ J25) and the Drum Unit Relay PCB (Y) (UN26). 5. Replace the Drum Unit (Y). 6. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0041 |
| Description: | ATR Sensor (Y) error or toner supply error Unable to adjust the control voltage at the time of ATR Sensor (Y) initialization. |
| Remedy: | 1. Check if the Drum Unit (Y) is installed. 2. Check the Drum Unit Relay PCB (Y) (UN26) 3. Check the Drum Unit Memory PCB (Y) (UN30) 4. Check the harness/connector between the DC Controller PCB (UN09/ J25) and the Drum Unit Relay PCB (Y) (UN26). 5. Replace the Drum Unit (Y). 6. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0050 |
| Description: | ATR patch failed to be created correctly or Patch Sensor error High density for the target at patch detection |
| Remedy: | 1. Clean the scanner’s window. 2. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open. 3. Check if the window of the Patch Sensor (UN43/ UN44) is soiled. 4. Check scar on the ITB. 5. Check movement of the Registration Shutter Solenoid (SL02). COPIER > FUNCTION > PART-CHK > SL to move SL02 6. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensors (UN43/J4007, UN44, J4006). 7.Replace the Drum Unit (Y) 8.Replace the Registration Patch Sensor Unit 9 Replace the ITB Unit. 10. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 11. Replace the Primary Transfer High Voltage PCB (UN04) 12. Replace the Developing High Voltage PCB (UN07) 13. Replace the Primary Charging High Voltage PCB (UN06) 14. Replace the Auxiliary High Voltage PCB (UN08) 15. Replace the Replace the DC Controller PCB (UN09) |
| Error code: | E020-0060 |
| Description: | ATR patch failed to be created correctly or Patch Sensor error High density for the target at patch detection |
| Remedy: | 1. Check the patch shape. 2. Clean the high voltage contact point with dry wiping or air blower. 3. Check the harness/connector between the DC Controller (UN09) and the High Voltage PCB. Between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) Between the DC Controller PCB (UN09/ J21, J22) and the Developing High Voltage PCB (UN07/ J451, J452) Between the DC Controller PCB (UN09/ J19) and the Auxiliary High Voltage PCB (UN08/J461, J462) Between the DC Controller PCB (J205) and the Primary Transfer High Voltage PCB (UN04/J1001) 4. Replace the Drum Unit (Y) 5. Replace the Registration Patch Sensor Unit 6. Replace the ITB Unit. 7. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 8. Replace the Primary Transfer High Voltage PCB (UN04) 9. Replace the Developing High Voltage PCB (UN07) 10. Replace the Primary Charging High Voltage PCB (UN06) 11. Replace the Auxiliary High Voltage PCB (UN08) 12. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0070 |
| Description: | Patch Sensor error The Patch Sensor could not read a patch properly. (Patch error due to software or the ITB Unit) |
| Remedy: | 1.Turn OFF and then ON the power. 2.Replace the ITB Unit. |
| Error code: | E020-0090 |
| Description: | ATR Sensor (Y) error or toner supply error The average of ATR Sensor (Y) detection value is the specified value or lower. |
| Remedy: | 1. Check if the Drum Unit (Y) is installed. 2. Check the Drum Unit Relay PCB (Y) (UN26) 3. Check the Drum Unit Memory PCB (Y) (UN30) 4. Check the harness/connector between the DC Controller PCB (UN09/ J25) and the Drum Unit Relay PCB (Y) (UN26). 5. Replace the Drum Unit (Y). 6. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0091 |
| Description: | ATR Sensor (Y) error or toner supply error The average of ATR Sensor (Y) detection value is the specified value or higher. |
| Remedy: | 1. Check if the Drum Unit (Y) is installed. 2. Check the Drum Unit Relay PCB (Y) (UN26) 3. Check the Drum Unit Memory PCB (Y) (UN30) 4. Check the harness/connector between the DC Controller PCB (UN09/ J25) and the Drum Unit Relay PCB (Y) (UN26). 5. Replace the Drum Unit (Y). 6. Replace the DC Controller PCB (UN09) |
| Error code: | E020-00B0 |
| Description: | ATR Sensor (Y) error or toner supply error T/D ratio detected by the ATR Sensor (Y) (UN39) is equal to or higher than the specified value (high density) |
| Remedy: | 1. Check if the Drum Unit (Y) is installed. 2. Check the Drum Unit Relay PCB (Y) (UN26) 3. Check the Drum Unit Memory PCB (Y) (UN30) 4. Check the harness/connector between the DC Controller PCB (UN09/ J25) and the Drum Unit Relay PCB (Y) (UN26). 5. Replace the Drum Unit (Y). 6. Replace the DC Controller PCB (UN09) |
| Error code: | E020-00B1 |
| Description: | ATR Sensor (Y) error or toner supply error Error in detected delta T/D ratio T/D ratio detected by the ATR Sensor (Y) (UN39) is equal to or lower than the specified value (light density) |
| Remedy: | Possible cause: overload with the motor or motor failure 1. Check conduction with FU2 on the DC Controller PCB (UN09) 2. Check the harness/connector between the DC Controller PCB (UN09/ J23) and PS06. 3. Replace the DC Controller PCB (UN09) 4. Check the Hopper Unit (Y) 5. Replace the Hopper Unit (Y). |
| Error code: | E020-0120 |
| Description: | Initial installation toner density sensor (Y) output lower limit error. When executing the developing assembly initial installation mode (COPIER> FUNCTION> INSTALL> INISET-Y), the output level does not reach 128 even when control voltage of the toner density sensor reached 255 or more. |
| Remedy: | 1. Check the connection between the toner density sensor and the DC controller PCB. (Connector, Breaking (Breaking (shorting))) <Y> sensor side: J7133, J8028, J8087 PCB side: J1244, J8085 <M> sensor side: J7134, J8029, J8088 PCB side: J1244, J8085 <C> sensor side: J7135, J8030, J8089 PCB side: J1244, J8086 <Bk> sensor side: J7146, J8015, J8117 PCB side: J1244, J8080 2. Check whether the toner density sensor is not disconnected or Breaking (Breaking (shorting)) occurs. 3. Replace the developing assembly. |
| Error code: | E020-0130 |
| Description: | Initial installation toner density sensor (Y) output upper limit error. When executing developing assembly initial installation mode (COPIER> FUNCTION> INSTALL> INISET-Y), the output level does not reach 128 even when control voltage of the toner density sensor became less than 55. |
| Remedy: | 1. Check the connection between the toner density sensor and the DC controller PCB. (Connector, Shorting) <Y> sensor side: J7133, J8028, J8087 PCB side: J1244, J8085 <M> sensor side: J7134, J8029, J8088 PCB side: J1244, J8085 <C> sensor side: J7135, J8030, J8089 PCB side: J1244, J8086 <Bk> sensor side: J7146, J8015, J8117 PCB side: J1244, J8080 2. Check whether disconnection or shorting of the toner density sensor occurs or not. 3. Replace the developing assembly. |
| Error code: | E020-0140 |
| Description: | Error in Y Developing Assembly Unable to adjust the control voltage at the time of ATR initialization: less than the specified value (3.2V). |
| Remedy: | 1. Check if the ATR Sensor (TS5) Connector is properly connected. 2. Check short-circuit of the ATR Sensor Harness. 3. Replace the Developing Assembly. |
| Error code: | E020-0141 |
| Description: | Error in Y Developing Assembly Unable to adjust the control voltage at the time of ATR initialization: exceeds the specified value (6.8V). |
| Remedy: | 1. Check short-circuit of the ATR Sensor (TS5) Harness. 2. Replace the Developing Assembly. |
| Error code: | E020-0150 |
| Description: | ATR patch failed to be created correctly or Patch Sensor error High density for the target at patch detection |
| Remedy: | 1. Clean the scanner’s window. 2. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open. 3. Check if the window of the Patch Sensor (UN43/ UN44) is soiled. 4. Check scar on the ITB. 5. Check movement of the Registration Shutter Solenoid (SL02). COPIER > FUNCTION > PART-CHK > SL to move SL02 6. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensors (UN43/J4007, UN44, J4006). 7.Replace the Drum Unit (M) 8.Replace the Registration Patch Sensor Unit 9 Replace the ITB Unit. 10. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 11. Replace the Primary Transfer High Voltage PCB (UN04) 12. Replace the Developing High Voltage PCB (UN07) 13. Replace the Primary Charging High Voltage PCB (UN06) 14. Replace the Auxiliary High Voltage PCB (UN08) 15. Replace the Replace the DC Controller PCB (UN09) |
| Error code: | E020-0160 |
| Description: | ATR patch failed to be created correctly or Patch Sensor error High density for the target at patch detection |
| Remedy: | 1. Check the patch shape. 2. Clean the high voltage contact point with dry wiping or air blower. 3. Check the harness/connector between the DC Controller (UN09) and the High Voltage PCB. Between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) Between the DC Controller PCB (UN09/ J21, J22) and the Developing High Voltage PCB (UN07/ J451, J452) Between the DC Controller PCB (UN09/ J19) and the Auxiliary High Voltage PCB (UN08/J461, J462) Between the DC Controller PCB (J205) and the Primary Transfer High Voltage PCB (UN04/J1001) 4. Replace the Drum Unit (M) 5. Replace the Registration Patch Sensor Unit 6. Replace the ITB Unit. 7. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 8. Replace the Primary Transfer High Voltage PCB (UN04) 9. Replace the Developing High Voltage PCB (UN07) 10. Replace the Primary Charging High Voltage PCB (UN06) 11. Replace the Auxiliary High Voltage PCB (UN08) 12. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0170 |
| Description: | Patch Sensor error The Patch Sensor could not read a patch properly. (Patch error due to software or the ITB Unit) |
| Remedy: | 1.Turn OFF and then ON the power. 2.Replace the ITB Unit. |
| Error code: | E020-0190 |
| Description: | Patch (Y) density lower limit error. The ATR patch detection output (SigD) is less than 79. |
| Remedy: | • When the value of COPIER> DISPLAY> DENS> P-LED-DA is large (153(D) or more) and the value of P-SENS-P is small, there is a high possibility that dirt is applied to the patch sensor. • This occurs only at a regular timing. When the value of COPIER> DISPLAY> DENS> DENS-S-x is small (2 digits), there is a high possibility that breaking occurred. 1. Check whether the developing assembly and the drum unit are properly installed. 2. Clean the patch sensor (PS21). 3. Check the connection between the patch sensor and the Drum ITB driver PCB (UN6). (Connector, Shorting) Sensor side: J7412, J8035 PCB side: J1907 4. Check open/close operation of the patch shutter. 5. Check whether scratches/dirt are applied to the ITB. If many scratches are found, replace the ITB. If dirt is applied, clean the ITB. In this case, check the ITB cleaning blade at the same time. 6. Replace the patch sensor unit. NOTE: This error also occurs when there is not enough toner in the developing assembly. In this case, check the supplyrelated parts in the developing assembly. |
| Error code: | E020-0191 |
| Description: | Patch (Y) density upper limit error. The ATR patch detection output (SigD) is more than 970. |
| Remedy: | • When the value of COPIER> DISPLAY> DENS> P-LED-DA is large (153(D) or more) and the value of COPIER> DISPLAY > DENS >P-SENS-P is small, there is a high possibility that dirt is applied to the patch sensor. • This occurs only at a regular timing. When the value of COPIER> DISPLAY> DENS> DENS-S-x is small (2 digits), there is a high possibility that breaking occurred. 1. Check whether the developing assembly and the drum unit are properly installed. 2. Clean the patch sensor (PS21). 3. Check the connection between the patch sensor and the Drum ITB driver PCB (UN6). (Connector, Shorting) Sensor side: J7412, J8035 PCB side: J1907 4. Check open/close operation of the patch shutter. 5. Check whether scratches/dirt are applied to the ITB. If many scratches are found, replace the ITB. If dirt is applied, clean the ITB. In this case, check the ITB cleaning blade at the same time. 6. Replace the patch sensor unit. NOTE: This error also occurs when there is not enough toner in the developing assembly. In this case, check the supplyrelated parts in the developing assembly. |
| Error code: | E020-01B0 |
| Description: | Error in Y Developing Assembly TD ratio lower limit error at the time of print sequence (Large amount of toner in the Developing Assembly) |
| Remedy: | Go through the following: DISPLAY > DENS > DENS-Y; if DENS-Y is slightly higher than 5.0%, output 10 sheets of solid image with the color causing the error (to reduce T/D ratio). See the Service Mode again to see if the problem is improved. Remedy is complete if it’s improved. If not, perform the following remedy work. 1. Check if the ATR Sensor (TS5) Connector is disconnected. 2. Check short-circuit of the ATR Sensor Harness. 3. Replace the Developing Assembly. |
| Error code: | E020-01B1 |
| Description: | Error in Y Developing Assembly TD ratio upper limit error at the time of print sequence (Small amount of toner in the Developing Assembly) |
| Remedy: | 1. Output 10 sheets of white (blank) sheets (to increase T/D ratio). 2. Check toner leak from the Toner Buffer Unit. 3. Check toner level in the Toner Container. 4. Replace the Developing Assembly. 5. Check short-circuit of the harness of the Toner supply sensor (PS1). |
| Error code: | E020-0220 |
| Description: | Initial installation toner density sensor (M) output lower limit error. When executing the developing assembly initial installation mode (COPIER> FUNCTION> INSTALL> INISET-M), the output level does not reach 128 even when control voltage of the toner density sensor reached 255 or more. |
| Remedy: | 1. Check the connection between the toner density sensor and the DC controller PCB. (Connector, Breaking (Breaking (shorting)) <Y> sensor side: J7133, J8028, J8087 PCB side: J1244, J8085 <M> sensor side: J7134, J8029, J8088 PCB side: J1244, J8085 <C> sensor side: J7135, J8030, J8089 PCB side: J1244, J8086 <Bk> sensor side: J7146, J8015, J8117 PCB side: J1244, J8080 2. Check whether the toner density sensor is not disconnected or Breaking (Breaking (shorting)) occurs. 3. Replace the developing assembly. |
| Error code: | E020-0230 |
| Description: | Initial installation toner density sensor (M) output upper limit error. When executing developing assembly initial installation mode (COPIER> FUNCTION> INSTALL> INISET-M), the output level does not reach 128 even when control voltage of the toner density sensor became less than 55. |
| Remedy: | 1. Check the connection between the toner density sensor and the DC controller PCB. (Connector, Shorting) <Y> sensor side: J7133, J8028, J8087 PCB side: J1244, J8085 <M> sensor side: J7134, J8029, J8088 PCB side: J1244, J8085 <C> sensor side: J7135, J8030, J8089 PCB side: J1244, J8086 <Bk> sensor side: J7146, J8015, J8117 PCB side: J1244, J8080 2. Check whether disconnection or shorting of the toner density sensor occurs or not. 3. Replace the developing assembly. |
| Error code: | E020-0240 |
| Description: | Error in M Developing Assembly Unable to adjust the control voltage at the time of ATR initialization: less than the specified value (3.2V). |
| Remedy: | 1. Check if the ATR Sensor (TS6) Connector is properly connected. 2. Check short-circuit of the ATR Sensor Harness. 3. Replace the Developing Assembly. |
| Error code: | E020-0241 |
| Description: | Error in M Developing Assembly Unable to adjust the control voltage at the time of ATR initialization: exceeds the specified value (6.8V). |
| Remedy: | 1. Check short-circuit of the ATR Sensor (TS6) Harness. 2. Replace the Developing Assembly. |
| Error code: | E020-0250 |
| Description: | ATR patch failed to be created correctly or Patch Sensor error High density for the target at patch detection |
| Remedy: | 1. Clean the scanner’s window. 2. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open. 3. Check if the window of the Patch Sensor (UN43/ UN44) is soiled. 4. Check scar on the ITB. 5. Check movement of the Registration Shutter Solenoid (SL02). COPIER > FUNCTION > PART-CHK > SL to move SL02 6. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensors (UN43/J4007, UN44, J4006). 7.Replace the Drum Unit (C) 8.Replace the Registration Patch Sensor Unit 9 Replace the ITB Unit. 10. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 11. Replace the Primary Transfer High Voltage PCB (UN04) 12. Replace the Developing High Voltage PCB (UN07) 13. Replace the Primary Charging High Voltage PCB (UN06) 14. Replace the Auxiliary High Voltage PCB (UN08) 15. Replace the Replace the DC Controller PCB (UN09) |
| Error code: | E020-0260 |
| Description: | ATR patch failed to be created correctly or Patch Sensor error High density for the target at patch detection |
| Remedy: | 1. Check the patch shape. 2. Clean the high voltage contact point with dry wiping or air blower. 3. Check the harness/connector between the DC Controller (UN09) and the High Voltage PCB. Between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) Between the DC Controller PCB (UN09/ J21, J22) and the Developing High Voltage PCB (UN07/ J451, J452) Between the DC Controller PCB (UN09/ J19) and the Auxiliary High Voltage PCB (UN08/J461, J462) Between the DC Controller PCB (J205) and the Primary Transfer High Voltage PCB (UN04/J1001) 4. Replace the Drum Unit (C) 5. Replace the Registration Patch Sensor Unit 6. Replace the ITB Unit. 7. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 8. Replace the Primary Transfer High Voltage PCB (UN04) 9. Replace the Developing High Voltage PCB (UN07) 10. Replace the Primary Charging High Voltage PCB (UN06) 11. Replace the Auxiliary High Voltage PCB (UN08) 12. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0290 |
| Description: | Patch (M) density lower limit error. The ATR patch detection output (SigD) is less than 79 |
| Remedy: | • When the value of COPIER> DISPLAY> DENS> P-LED-DA is large (153(D) or more) and the value of P-SENS-P is small, there is a high possibility that dirt is applied to the patch sensor. • This occurs only at a regular timing. When the value of COPIER> DISPLAY> DENS> DENS-S-x is small (2 digits), there is a high possibility that breaking occurred. 1. Check whether the developing assembly and the drum unit are properly installed. 2. Clean the patch sensor (PS21). 3. Check the connection between the patch sensor and the Drum ITB driver PCB (UN6). (Connector, Shorting) Sensor side: J7412, J8035 PCB side: J1907 4. Check open/close operation of the patch shutter. 5. Check whether scratches/dirt are applied to the ITB. If many scratches are found, replace the ITB. If dirt is applied, clean the ITB. In this case, check the ITB cleaning blade at the same time. 6. Replace the patch sensor unit. NOTE: This error also occurs when there is not enough toner in the developing assembly. In this case, check the supplyrelated parts in the developing assembly. |
| Error code: | E020-0291 |
| Description: | Patch (M) density upper limit error. The ATR patch detection output (SigD) is more than 970. |
| Remedy: | • When the value of COPIER> DISPLAY> DENS> P-LED-DA is large (153(D) or more) and the value of P-SENS-P is small, there is a high possibility that dirt is applied to the patch sensor. • This occurs only at a regular timing. When the value of COPIER> DISPLAY> DENS> DENS-S-x is small (2 digits), there is a high possibility that breaking occurred. 1. Check whether the developing assembly and the drum unit are properly installed. 2. Clean the patch sensor (PS21). 3. Check the connection between the patch sensor and the Drum ITB driver PCB (UN6). (Connector, Shorting) Sensor side: J7412, J8035 PCB side: J1907 4. Check open/close operation of the patch shutter. 5. Check whether scratches/dirt are applied to the ITB. If many scratches are found, replace the ITB. If dirt is applied, clean the ITB. In this case, check the ITB cleaning blade at the same time. 6. Replace the patch sensor unit. NOTE: This error also occurs when there is not enough toner in the developing assembly. In this case, check the supplyrelated parts in the developing assembly. |
| Error code: | E020-02B0 |
| Description: | Error in M Developing Assembly TD ratio lower limit error at the time of print sequence (Large amount of toner in the Developing Assembly) |
| Remedy: | Go through the following: DISPLAY > DENS > DENS-M; if DENS-M is slightly higher than 5.0%, output 10 sheets of solid image with the color causing the error (to reduce T/D ratio). See the Service Mode again to see if the problem is improved. Remedy is complete if it’s improved. If not, perform the following remedy work. 1. Check if the ATR Sensor (TS6) Connector is disconnected. 2. Check short-circuit of the ATR Sensor Harness. 3. Replace the Developing Assembly. |
| Error code: | E020-02B1 |
| Description: | Error in M Developing Assembly TD ratio upper limit error at the time of print sequence (Small amount of toner in the Developing Assembly) |
| Remedy: | 1. Output 10 sheets of white (blank) sheets (to increase T/D ratio). 2. Check toner leak from the Toner Buffer Unit. 3. Check toner level in the Toner Container. 4. Replace the Developing Assembly. 5. Check short-circuit of the harness of the Toner supply sensor (PS2). |
| Error code: | E020-0320 |
| Description: | Initial installation toner density sensor (C) output lower limit error. When executing the developing assembly initial installation mode (COPIER> FUNCTION> INSTALL> INISET-C), the output level does not reach 128 even when control voltage of the toner density sensor reached 255 or more. |
| Remedy: | 1. Check the connection between the toner density sensor and the DC controller PCB. (Connector, Breaking (Breaking (shorting))) <Y> sensor side: J7133, J8028, J8087 PCB side: J1244, J8085 <M> sensor side: J7134, J8029, J8088 PCB side: J1244, J8085 <C> sensor side: J7135, J8030, J8089 PCB side: J1244, J8086 <Bk> sensor side: J7146, J8015, J8117 PCB side: J1244, J8080 2. Check whether the toner density sensor is not disconnected or Breaking (Breaking (shorting)) occurs. 3. Replace the developing assembly. |
| Error code: | E020-0330 |
| Description: | Initial installation toner density sensor (C) output upper limit error. When executing developing assembly initial installation mode (COPIER> FUNCTION> INSTALL> INISET-C), the output level does not reach 128 even when control voltage of the toner density sensor became less than 55 |
| Remedy: | 1. Check the connection between the toner density sensor and the DC controller PCB. (Connector, Shorting) <Y> sensor side: J7133, J8028, J8087 PCB side: J1244, J8085 <M> sensor side: J7134, J8029, J8088 PCB side: J1244, J8085 <C> sensor side: J7135, J8030, J8089 PCB side: J1244, J8086 <Bk> sensor side: J7146, J8015, J8117 PCB side: J1244, J8080 2. Check whether disconnection or shorting of the toner density sensor occurs or not. 3. Replace the developing assembly. |
| Error code: | E020-0340 |
| Description: | Initial installation toner density sensor (Bk) output upper limit error. When executing developing assembly initial installation mode (COPIER>FUNCTION>INSTALL>INISET-K), the output level does not reach 128 even when control voltage of the toner density sensor became less than 55. |
| Remedy: | 1. Check the connection between the toner density sensor and the DC controller interface PCB. (Connector, Shorting) <Y> sensor side: J7133, J8028, J8087 PCB side: J1240, J8085 <M> sensor side: J7134, J8029, J8088 PCB side: J1240, J8085 <C> sensor side: J7135, J8030, J8089 PCB side: J1240, J8086 <Bk> sensor side: J7146, J8015, J8117 PCB side: J1240, J8086 2. Check whether disconnection or shorting of the toner density sensor occurs or not. 3. Replace the developing assembly. |
| Error code: | E020-0341 |
| Description: | Error in C Developing Assembly Unable to adjust the control voltage at the time of ATR initialization: exceeds the specified value (6.8V). |
| Remedy: | 1. Check short-circuit of the ATR Sensor (TS7) Harness. 2. Replace the Developing Assembly. |
| Error code: | E020-0350 |
| Description: | ATR patch failed to be created correctly or Patch Sensor error High density for the target at patch detection |
| Remedy: | 1. Clean the scanner’s window. 2. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open. 3. Check if the window of the Patch Sensor (UN43/ UN44) is soiled. 4. Check scar on the ITB. 5. Check movement of the Registration Shutter Solenoid (SL02). COPIER > FUNCTION > PART-CHK > SL to move SL02 6. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensors (UN43/J4007, UN44, J4006). 7.Replace the Drum Unit (Bk) 8.Replace the Registration Patch Sensor Unit 9 Replace the ITB Unit. 10. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 11. Replace the Primary Transfer High Voltage PCB (UN04) 12. Replace the Developing High Voltage PCB (UN07) 13. Replace the Primary Charging High Voltage PCB (UN06) 14. Replace the Auxiliary High Voltage PCB (UN08) 15. Replace the Replace the DC Controller PCB (UN09) |
| Error code: | E020-0360 |
| Description: | ATR patch failed to be created correctly or Patch Sensor error High density for the target at patch detection |
| Remedy: | 1. Check the patch shape. 2. Clean the high voltage contact point with dry wiping or air blower. 3. Check the harness/connector between the DC Controller (UN09) and the High Voltage PCB. Between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) Between the DC Controller PCB (UN09/ J21, J22) and the Developing High Voltage PCB (UN07/ J451, J452) Between the DC Controller PCB (UN09/ J19) and the Auxiliary High Voltage PCB (UN08/J461, J462) Between the DC Controller PCB (J205) and the Primary Transfer High Voltage PCB (UN04/J1001) 4. Replace the Drum Unit (Bk) 5. Replace the Registration Patch Sensor Unit 6. Replace the ITB Unit. 7. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 8. Replace the Primary Transfer High Voltage PCB (UN04) 9. Replace the Developing High Voltage PCB (UN07) 10. Replace the Primary Charging High Voltage PCB (UN06) 11. Replace the Auxiliary High Voltage PCB (UN08) 12. Replace the DC Controller PCB (UN09) |
| Error code: | E020-0390 |
| Description: | Patch (C) density lower limit error. The ATR patch detection output (SigD) is less than 79. |
| Remedy: | • When the value of COPIER> DISPLAY> DENS> P-LED-DA is large (153(D) or more) and the value of P-SENS-P is small, there is a high possibility that dirt is applied to the patch sensor. • This occurs only at a regular timing. When the value of COPIER> DISPLAY> DENS> DENS-S-x is small (2 digits), there is a high possibility that breaking occurred. 1. Check whether the developing assembly and the drum unit are properly installed. 2. Clean the patch sensor (PS21) . 3. Check the connection between the patch sensor and the Drum ITB driver PCB (UN6). (Connector, Shorting) Sensor side: J7412, J8035 PCB side: J1907 4. Check open/close operation of the patch shutter. 5. Check whether scratches/dirt are applied to the ITB. If many scratches are found, replace the ITB. If dirt is applied, clean the ITB. In this case, check the ITB cleaning blade at the same time. 6. Replace the patch sensor unit. NOTE: This error also occurs when there is not enough toner in the developing assembly. In this case, check the supplyrelated parts in the developing assembly |
| Error code: | E020-0391 |
| Description: | Patch (C) density upper limit error. The ATR patch detection output (SigD) is more than 970. |
| Remedy: | • When the value of COPIER> DISPLAY> DENS> P-LED-DA is large (153(D) or more) and the value of P-SENS-P is small, there is a high possibility that dirt is applied to the patch sensor. • This occurs only at a regular timing. When the value of COPIER> DISPLAY> DENS> DENS-S-x is small (2 digits), there is a high possibility that breaking occurred. 1. Check whether the developing assembly and the drum unit are properly installed. 2. Clean the patch sensor (PS21) . 3. Check the connection between the patch sensor and the Drum ITB driver PCB (UN6). (Connector, Shorting) Sensor side: J7412, J8035 PCB side: J1907 4. Check open/close operation of the patch shutter. 5. Check whether scratches/dirt are applied to the ITB. If many scratches are found, replace the ITB. If dirt is applied, clean the ITB. In this case, check the ITB cleaning blade at the same time. 6. Replace the patch sensor unit. NOTE: This error also occurs when there is not enough toner in the developing assembly. In this case, check the supplyrelated parts in the developing assembly. |
| Error code: | E020-03B0 |
| Description: | Error in C Developing Assembly TD ratio lower limit error at the time of print sequence (Large amount of toner in the Developing Assembly)s. |
| Remedy: | Go through the following: DISPLAY > DENS > DENS-C; if DENS-C is slightly higher than 5.0%, output 10 sheets of solid image with the color causing the error (to reduce T/D ratio). See the Service Mode again to see if the problem is improved. Remedy is complete if it’s improved. If not, perform the following remedy work. 1. Check if the ATR Sensor (TS7) Connector is disconnected. 2. Check short-circuit of the ATR Sensor Harness. 3. Replace the Developing Assembly. |
| Error code: | E020-03B1 |
| Description: | Error in C Developing Assembly TD ratio upper limit error at the time of print sequence (Small amount of toner in the Developing Assembly) |
| Remedy: | 1. Output 10 sheets of white (blank) sheets (to increase T/D ratio). 2. Check toner leak from the Toner Buffer Unit. 3. Check toner level in the Toner Container. 4. Replace the Developing Assembly. 5. Check short-circuit of the harness of the Toner supply sensor (PS3). |
| Error code: | E020-1050 |
| Description: | Abnormal Y color patch reading value Dark patch although setting 0 for the patch level |
| Remedy: | 1. Clean the scanner’s window. 2. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open. 3. Check if the window of the Patch Sensor (UN43/ UN44) is soiled. 4. Check scar on the ITB. 5. Check movement of the Registration Shutter Solenoid (SL02). COPIER > FUNCTION > PART-CHK > SL to move SL02 6. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensors (UN43/J4007, UN44, J4006). 7.Replace the Drum Unit (Y) 8.Replace the Registration Patch Sensor Unit 9 Replace the ITB Unit. 10. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 11. Replace the Primary Transfer High Voltage PCB (UN04) 12. Replace the Developing High Voltage PCB (UN07) 13. Replace the Primary Charging High Voltage PCB (UN06) 14. Replace the Auxiliary High Voltage PCB (UN08) 15. Replace the Replace the DC Controller PCB (UN09) |
| Error code: | E020-1060 |
| Description: | Abnormal Y color patch reading value Light patch although setting 7 for patch level |
| Remedy: | 1. Check the patch shape. 2. Clean the high voltage contact point with dry wiping or air blower. 3. Check the harness/connector between the DC Controller (UN09) and the High Voltage PCB. Between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) Between the DC Controller PCB (UN09/ J21, J22) and the Developing High Voltage PCB (UN07/ J451, J452) Between the DC Controller PCB (UN09/ J19) and the Auxiliary High Voltage PCB (UN08/J461, J462) Between the DC Controller PCB (J205) and the Primary Transfer High Voltage PCB (UN04/J1001) 4. Replace the Drum Unit (Y) 5. Replace the Registration Patch Sensor Unit 6. Replace the ITB Unit. 7. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 8. Replace the Primary Transfer High Voltage PCB (UN04) 9. Replace the Developing High Voltage PCB (UN07) 10. Replace the Primary Charging High Voltage PCB (UN06) 11. Replace the Auxiliary High Voltage PCB (UN08) 12. Replace the DC Controller PCB (UN09) |
| Error code: | E020-1150 |
| Description: | Abnormal M color patch reading value Dark patch although setting 0 for the patch level |
| Remedy: | 1. Clean the scanner’s window. 2. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open. 3. Check if the window of the Patch Sensor (UN43/ UN44) is soiled. 4. Check scar on the ITB. 5. Check movement of the Registration Shutter Solenoid (SL02). COPIER > FUNCTION > PART-CHK > SL to move SL02 6. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensors (UN43/J4007, UN44, J4006). 7.Replace the Drum Unit (M) 8.Replace the Registration Patch Sensor Unit 9 Replace the ITB Unit. 10. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 11. Replace the Primary Transfer High Voltage PCB (UN04) 12. Replace the Developing High Voltage PCB (UN07) 13. Replace the Primary Charging High Voltage PCB (UN06) 14. Replace the Auxiliary High Voltage PCB (UN08) 15. Replace the Replace the DC Controller PCB (UN09) |
| Error code: | E020-1160 |
| Description: | Abnormal M color patch reading value Light patch although setting 7 for patch level (unable to fit in the target between 550 and 640) |
| Remedy: | 1. Check the patch shape. 2. Clean the high voltage contact point with dry wiping or air blower. 3. Check the harness/connector between the DC Controller (UN09) and the High Voltage PCB. Between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) Between the DC Controller PCB (UN09/ J21, J22) and the Developing High Voltage PCB (UN07/ J451, J452) Between the DC Controller PCB (UN09/ J19) and the Auxiliary High Voltage PCB (UN08/J461, J462) Between the DC Controller PCB (J205) and the Primary Transfer High Voltage PCB (UN04/J1001) 4. Replace the Drum Unit (M) 5. Replace the Registration Patch Sensor Unit 6. Replace the ITB Unit. 7. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 8. Replace the Primary Transfer High Voltage PCB (UN04) 9. Replace the Developing High Voltage PCB (UN07) 10. Replace the Primary Charging High Voltage PCB (UN06) 11. Replace the Auxiliary High Voltage PCB (UN08) 12. Replace the DC Controller PCB (UN09) |
| Error code: | E020-1250 |
| Description: | Abnormal C color patch reading value Dark patch although setting 0 for the patch level |
| Remedy: | 1. Clean the scanner’s window. 2. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open. 3. Check if the window of the Patch Sensor (UN43/ UN44) is soiled. 4. Check scar on the ITB. 5. Check movement of the Registration Shutter Solenoid (SL02). COPIER > FUNCTION > PART-CHK > SL to move SL02 6. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensors (UN43/J4007, UN44, J4006). 7.Replace the Drum Unit (C) 8.Replace the Registration Patch Sensor Unit 9 Replace the ITB Unit. 10. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 11. Replace the Primary Transfer High Voltage PCB (UN04) 12. Replace the Developing High Voltage PCB (UN07) 13. Replace the Primary Charging High Voltage PCB (UN06) 14. Replace the Auxiliary High Voltage PCB (UN08) 15. Replace the Replace the DC Controller PCB (UN09) |
| Error code: | E020-1260 |
| Description: | Abnormal C color patch reading value Light patch although setting 7 for patch level (unable to fit in the target between 550 and 640) |
| Remedy: | 1. Check the patch shape. 2. Clean the high voltage contact point with dry wiping or air blower. 3. Check the harness/connector between the DC Controller (UN09) and the High Voltage PCB. Between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) Between the DC Controller PCB (UN09/ J21, J22) and the Developing High Voltage PCB (UN07/ J451, J452) Between the DC Controller PCB (UN09/ J19) and the Auxiliary High Voltage PCB (UN08/J461, J462) Between the DC Controller PCB (J205) and the Primary Transfer High Voltage PCB (UN04/J1001) 4. Replace the Drum Unit (C) 5. Replace the Registration Patch Sensor Unit 6. Replace the ITB Unit. 7. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 8. Replace the Primary Transfer High Voltage PCB (UN04) 9. Replace the Developing High Voltage PCB (UN07) 10. Replace the Primary Charging High Voltage PCB (UN06) 11. Replace the Auxiliary High Voltage PCB (UN08) 12. Replace the DC Controller PCB (UN09) |
| Error code: | E020-1350 |
| Description: | Abnormal Bk color patch reading value Dark patch although setting 0 for the patch level |
| Remedy: | 1. Clean the scanner’s window. 2. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open. 3. Check if the window of the Patch Sensor (UN43/ UN44) is soiled. 4. Check scar on the ITB. 5. Check movement of the Registration Shutter Solenoid (SL02). COPIER > FUNCTION > PART-CHK > SL to move SL02 6. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensors (UN43/J4007, UN44, J4006). 7.Replace the Drum Unit (Bk) 8.Replace the Registration Patch Sensor Unit 9 Replace the ITB Unit. 10. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 11. Replace the Primary Transfer High Voltage PCB (UN04) 12. Replace the Developing High Voltage PCB (UN07) 13. Replace the Primary Charging High Voltage PCB (UN06) 14. Replace the Auxiliary High Voltage PCB (UN08) 15. Replace the Replace the DC Controller PCB (UN09) |
| Error code: | E020-1360 |
| Description: | Abnormal Bk color patch reading value Light patch although setting 7 for patch level |
| Remedy: | 1. Check the patch shape. 2. Clean the high voltage contact point with dry wiping or air blower. 3. Check the harness/connector between the DC Controller (UN09) and the High Voltage PCB. Between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) Between the DC Controller PCB (UN09/ J21, J22) and the Developing High Voltage PCB (UN07/ J451, J452) Between the DC Controller PCB (UN09/ J19) and the Auxiliary High Voltage PCB (UN08/J461, J462) Between the DC Controller PCB (J205) and the Primary Transfer High Voltage PCB (UN04/J1001) 4. Replace the Drum Unit (Bk) 5. Replace the Registration Patch Sensor Unit 6. Replace the ITB Unit. 7. Check conduction of the fuses (FU5, FU8) in the DC Controller PCB (UN09). 8. Replace the Primary Transfer High Voltage PCB (UN04) 9. Replace the Developing High Voltage PCB (UN07) 10. Replace the Primary Charging High Voltage PCB (UN06) 11. Replace the Auxiliary High Voltage PCB (UN08) 12. Replace the DC Controller PCB (UN09) |
| Error code: | E021-0001 |
| Description: | There is an error in the rotation of the developing assembly. The developing rotary home position is not detected. The motor rotates out of sync because of poor torque caused by any of the following: The developing rotary HP sensor is faulty; the wiring of the DC controller is faulty; there is an excess load on the developing assembly. |
| Remedy: | Turn off and then on the main power. |
| Error code: | E021-0003 |
| Description: | Error in developing motor |
| Causes: | Motor (Bk) rotation error |
| Error code: | E021-0020 |
| Description: | Developing screw rotation detection Error in the difference between the maximum and the minimum of ATR Sensor (Y) detection value. |
| Remedy: | Possible cause: The screw is not rotating due to failure in the coupling between the main body and the Developing Assembly, or the value of ATR Sensor (Y) (UN39) failed to be read due to an electrical trouble. 1. Remove the Drum Unit (Y) and check no damage. (Replace the Drum Unit (Y) if defective) 2. Lift the pressure lever after the Drum Unit (Y) is pushed all the way in. 3. Check failure of the harness between the Drum Unit (Y) and the DC Controller PCB (UN09/J25) (trapped cable, open circuit, connector disconnection) 4.Check the Drum Unit Relay PCB (Y) (UN26) (Soil/ deformation/ damage) 5. Check the Drum Unit Memory PCB (M) (UN30) (Soil/ damage) 6.Replace the Drum Unit (Y) 7. Replace the DC Controller PCB (UN09). 8. Replace the Main Drive Unit |
| Error code: | E021-0120 |
| Description: | Developing screw rotation detection Error in the difference between the maximum and the minimum of ATR Sensor (M) detection value. |
| Remedy: | Possible cause: The screw is not rotating due to failure in the coupling between the main body and the Developing Assembly, or the value of ATR Sensor (M) (UN40) failed to be read due to an electrical trouble. 1. Remove the Drum Unit (M) and check no damage. (Replace the Drum Unit (M) if defective) 2. Lift the pressure lever after the Drum Unit (M) is pushed all the way in. 3. Check failure of the harness between the Drum Unit (M) and the DC Controller PCB (UN09/J25) (trapped cable, open circuit, connector disconnection) 4.Check the Drum Unit Relay PCB (M) (UN27) (Soil/ deformation/ damage) 5. Check the Drum Unit Memory PCB (M) (UN31) (Soil/ damage) 6.Replace the Drum Unit (M) 7. Replace the DC Controller PCB (UN09). 8. Replace the Main Drive Unit |
| Error code: | E021-0220 |
| Description: | Developing screw rotation detection Error in the difference between the maximum and the minimum of ATR Sensor (C) detection value. |
| Remedy: | Possible cause: The screw is not rotating due to failure in the coupling between the main body and the Developing Assembly, or the value of ATR Sensor (C)(UN41) failed to be read due to an electrical trouble. 1. Remove the Drum Unit (C) and check no damage. (Replace the Drum Unit (C) if defective) 2. Lift the pressure lever after the Drum Unit (C) is pushed all the way in. 3.Check failure of the harness between the Drum Unit (C) and the DC Controller PCB (UN09/J25) (trapped cable, open circuit, connector disconnection) 4.Check the Drum Unit Relay PCB (C) (UN28) (Soil/ deformation/ damage) 5.Check the Drum Unit Memory PCB (C) (UN32) (Soil/ damage) 6.Replace the Drum Unit (C). 7. Replace the DC Controller PCB (UN09). 8. Replace the Main Drive Unit |
| Error code: | E021-0320 |
| Description: | Developing screw rotation detection Error in the difference between the maximum and the minimum of ATR Sensor (Bk) detection value. |
| Remedy: | Possible cause: The screw is not rotating due to failure in the coupling between the main body and the Developing Assembly, or the value of ATR Sensor (Bk) (UN42) failed to be read due to an electrical trouble 1. Remove the Drum Unit (Bk) and check no damage. (Replace the Drum Unit (Bk) if defective) 2. Lift the pressure lever after the Drum Unit (Bk) is pushed all the way in. 3. Check failure of the harness between the Drum Unit (Bk) and the DC Controller PCB (UN09/J25) (trapped cable, open circuit, connector disconnection) 4.Check the Drum Unit Relay PCB (Bk) (UN29) (Soil/ deformation/ damage) 5. Check the Drum Unit Memory PCB (Bk) (UN33) (Soil/ damage) 6.Replace the Drum Unit (Bk). 7. Replace the DC Controller PCB (UN09). 8. Replace the Main Drive Unit |
| Error code: | E022-0000 |
| Description: | Error in detection of abnormal opening/closing of the Laser Shutter At the Dustproof Shutter open/close control, the sensor fails to detect although the specified time has passed. |
| Remedy: | Error in the Shutter Motor or the Laser Shutter Sensor 1.COPIER > FUNCTION > PART-CHK > MTR; move M05 When it works 2-1. Check the harness between the DC Controller (UN09/ J11) and the Laser Shutter Sensor (PS05) 3-1. Check condition of the Laser Shutter 4-1. Check the Laser Shutter Sensor (PS05) in the Main Drive 5-1. Replace the Main Drive When it does not work 2-2. Check the harness between the DC Controller (UN09/ J31) and the Developing Disengagement Motor (M05) 3-2. Check conduction of the fuse (FU6) in the DC Controller (UN09) 4-2. Replace the Laser Shutter Motor (M05) 5-2. Replace the Main Drive |
| Error code: | E025-0000 |
| Description: | Error in the toner motor Indicates an error of Y developing assembly toner supply |
| Remedy: | Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor |
| Error code: | E025-0010 |
| Description: | Toner Container Motor (Y) lock detection Error in the current value after turning ON the motor. |
| Remedy: | Overload of the motor or motor failure 1. Check if the Toner Bottle (Y) is installed 2. Check the harness/connector between the DC Controller PCB (UN09) and the Toner Container Motor (Y) (M07) 3. Check conduction of FU1 in the DC Controller PCB (UN09) 4. Replace the DC Controller PCB (UN09) 5. Replace the Hopper Unit (Y) |
| Error code: | E025-0020 |
| Description: | Detection of short-circuit with Toner Container Motor (Y)FET Error in element in the DC Controller PCB Error in the current value after turning OFF the motor. |
| Remedy: | 1.Replace the DC Controller PCB (UN09) |
| Error code: | E025-0030 |
| Description: | Detection of short-circuit with Toner Container Motor (Y) GND After turning ON the motor, the current value is a certain value or lower. |
| Remedy: | Short-circuit failure of the Toner Bottle Motor or error in element in the DC Controller PCB 1. Check the harness between the DC Controller (UN09/J23) and the Toner Container Motor (Y) (M07) 2. Replace the DC Controller PCB (UN09) 3. Replace the Hopper Unit (Y) |
| Error code: | E025-0100 |
| Description: | Error in the toner motor Y buffer supply error |
| Remedy: | Check on connection of the toner motor and the DC controller PCB, Replace the DC controller PCB, Replace the toner motor |
| Error code: | E025-0110 |
| Description: | Toner container sealing/release holder shift cam HP sensor timeout (Y) error. HP sensor of release holder shift cam cannot detect within specified period of time. |
| Remedy: | 1. Check the connection of the toner container drive motor (M10) harness. (Check whether the wire is not caught by parts.) Check the connection with the DC controller PCB. Motor side: J7100 PCB side: J1247 2. Check the connection between the release holder shift cam HP sensor (PS8) and the DC controller PCB. Sensor side: J7135, J8040 PCB side: J1248 3. Replace the toner container drive motor. 4. Clean and replace the release holder shift cam HP sensor. 5. Replace the hopper unit. CAUTION: As for Remedy 5, since it is difficult to identify the cause, it is recommended to replace the unit. NOTE: After performing the above remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR |
| Error code: | E025-0120 |
| Description: | Toner container/toner container inserting inlet phase (Y) error. When the power was turned on, it was detected that the toner container cap was opened (the release holder shift cam phase sensor was protected against light) AND the toner container inserting inlet cover was opened (the toner container inserting inlet cover open/close sensor was transmissive). |
| Remedy: | 1. Close the toner container inserting inlet cover and turn OFF/ON the power. 2. Check the connection between the toner container inserting inlet cover open/close sensor (PS10) and the DC controller PCB. (Connection of the connector, Breaking, Wire caught by parts) Sensor side: J7122, PCB side: J2146 3. Check the connection between the release holder shift cam phase sensor (PS81) and the DC controller PCB. (Connection of the connector, Breaking, Wire caught by parts) Sensor side: J7123,J8106, PCB side: J1247 4. Replace the toner container inserting inlet cover open/ close sensor |
| Error code: | E025-0130 |
| Description: | Detection of short-circuit with Toner Container Motor (M) GND After turning ON the motor, the current value is a certain value or lower. |
| Remedy: | Short-circuit failure of the Toner Bottle Motor or error in element in the DC Controller PCB 1. Check the harness between the DC Controller (UN09/J24) and the Toner Container Motor (M) (M09) 2. Replace the DC Controller PCB (UN09) 3. Replace the Hopper Unit (M) |
| Error code: | E025-0200 |
| Description: | Toner bottle motor lock (M) error. Overcurrent of the toner container drive motor was detected. |
| Remedy: | 1. Check whether a toner container of a different model is not installed. If it is installed, replace it with a correct one. 2. Check the connection of the toner container drive motor (M7/M10/M13/M16). (Check whether the wire is not caught by parts.) 3. Replace the toner container drive motor (M7/M10/M13/ M16). 4. Replace the toner container tray unit (when this error occurred at rotation of the toner container). 5. Replace the hopper unit. Points to note: When this error occurred because a toner container of a different model was installed, remove the toner container following the procedures shown below. 1) Open the toner container installation inlet cover. 2) Manually turn the container in an counterclockwise direction until it is fully turned. 3) Rotate the toner container in an counterclockwise direction using a toner container removing tool. 4) The toner container is placed at the position where it can be removed. Remove the toner container. |
| Error code: | E025-0210 |
| Description: | Toner container sealing/release holder shift cam HP sensor timeout (M) error. HP sensor of release holder shift cam cannot detect within specified period of time. |
| Remedy: | 1. Check the connection of the toner container drive motor (M13) harness. (Check whether the wire is not caught by parts.) Check the connection with the DC controller PCB. Motor side: J7101,J8107, PCB side: J1247 2. Check the connection between the release holder shift cam HP sensor (PS14) and the DC controller PCB. Sensor side: J7198 PCB side: J1249 3. Replace the toner container drive motor. 4. Clean and replace the release holder shift cam HP sensor. 5. Replace the hopper unit. CAUTION: As for Remedy 5, since it is difficult to identify the cause, it is recommended to replace the unit. NOTE: After performing the above remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR |
| Error code: | E025-0220 |
| Description: | Toner container/toner container inserting inlet phase (M) error. When the power was turned on, it was detected that the toner container cap was opened (the release holder shift cam phase sensor was protected against light) AND the toner container inserting inlet cover was opened (the toner container inserting inlet cover open/close sensor was transmissive). |
| Remedy: | 1. Close the toner container inserting inlet cover and turn OFF/ON the power. 2. Check the connection between the toner container inserting inlet cover open/close sensor (PS13) and the DC controller PCB. (Connection of the connector, Breaking, Wire caught by parts) Sensor side: J7125 PCB side: J1246 3. Check the connection between the release holder shift cam phase sensor (PS82) and the hopper driver PCB. (Connection of the connector, Breaking, Wire caught by parts) Sensor side: J7126 PCB side: J1247 4. Replace the toner container inserting inlet cover open/ close sensor. |
| Error code: | E025-0230 |
| Description: | Detection of short-circuit with Toner Container Motor (C) GND After turning ON the motor, the current value is a certain value or lower. |
| Remedy: | Short-circuit failure of the Toner Bottle Motor or error in element in the DC Controller PCB 1. Check the harness between the DC Controller (UN09/J24) and the Toner Container Motor (C) (M11) 2. Replace the DC Controller PCB (UN09) 3. Replace the Hopper Unit (C) |
| Error code: | E025-0300 |
| Description: | Toner bottle motor lock (C) error. Overcurrent of the toner container drive motor was detected. |
| Remedy: | 1. Check whether a toner container of a different model is not installed. If it is installed, replace it with a correct one. 2. Check the connection of the toner container drive motor (M7/M10/M13/M16). (Check whether the wire is not caught by parts.) 3. Replace the toner container drive motor (M7/M10/M13/ M16). 4. Replace the toner container tray unit (when this error occurred at rotation of the toner container). 5. Replace the hopper unit. Points to note: When this error occurred because a toner container of a different model was installed, remove the toner container following the procedures shown below. 1) Open the toner container installation inlet cover. 2) Manually turn the container in an counterclockwise direction until it is fully turned. 3) Rotate the toner container in an counterclockwise direction using a toner container removing tool. 4) The toner container is placed at the position where it can be removed. Remove the toner container. |
| Error code: | E025-0310 |
| Description: | Toner container sealing/release holder shift cam HP sensor timeout (C) error. HP sensor of release holder shift cam cannot detect within specified period of time. |
| Remedy: | 1. Check the connection of the toner container drive motor (M16) harness. (Check whether the wire is not caught by parts.) Check the connection with the DC controller PCB. SinceMotor side: J7102,J8108 PCB side: J1248 2. Check the connection between the release holder shift cam HP sensor (PS17) and the DC controller PCB. SinceSensor side: J7197, PCB side: J1249 3. Replace the toner container drive motor. 4. Clean and replace the release holder shift cam HP sensor. 5. Replace the hopper unit. CAUTION: As for Remedy 5, since it is difficult to identify the cause, it is recommended to replace the unit. NOTE: After performing the above remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR |
| Error code: | E025-0320 |
| Description: | Toner container/toner container inserting inlet phase (C) error. When the power was turned on, it was detected that the toner container cap was opened (the release holder shift cam phase sensor was protected against light) AND the toner container inserting inlet cover was opened (the toner container inserting inlet cover open/close sensor was transmissive). |
| Remedy: | 1. Close the toner container inserting inlet cover and turn OFF/ON the power. 2. Check the connection between the toner container inserting inlet cover open/close sensor (PS16) and the DC controller PCB. (Connection of the connector, Shorting, Wire caught by parts) Sensor side: J7128, PCB side: J1246 3. Check the connection between the release holder shift cam phase sensor (PS82) and the DC controller PCB. (Connection of the connector, Shorting, Wire caught by parts) Sensor side: J7129, PCB side: J1248 4. Replace the toner container inserting inlet cover open/ close sensor. |
| Error code: | E025-0330 |
| Description: | Detection of short-circuit with Toner Container Motor (Bk) GND After turning ON the motor, the current value is a certain value or lower |
| Remedy: | Short-circuit failure of the Toner Bottle Motor or error in element in the DC Controller PCB 1. Check the harness between the DC Controller (UN09/J26) and the Toner Container Motor (Bk) (M13) 2. Replace the DC Controller PCB (UN09) 3. Replace the Hopper Unit (Bk) |
| Error code: | E032-0001 |
| Description: | NE controller counter operation failure When the counter function of the NE controller does not work |
| Causes: | The DA unit is faulty. The main controller PCB is faulty. |
| Remedy: | Check the cable connections. |
| Error code: | E040-0002 |
| Description: | Cassette 1 Lifter error Unable to detect the lift-up completion position within 4.5 sec after lift-up was started |
| Remedy: | Error in Lift Motor or Lifter Sensor 1. While Cassette 1 is removed, turn ON the power and then insert Cassette 1. When there is operation sound of the motor 1-1. Check the harness/connector between the DC Controller (UN09/J13) and the Cassette 1 Lifter Sensor (PS12) 2-1. Check if the Cassette 1 Lifter Sensor (PS12) is installed. 3-1. Extend the Sensor Flag of the Cassette 1 Lifter Sensor (PS12) by approx. 1.5 mm with Plastic Film, etc. 4-1. Check the condition of the gear at the host machine side (to see if there is missing or swing with the gear) 5-1. Replace the Cassette 1 Lifter Sensor (PS12) 6-1. Replace the DC Controller PCB (UN09) When there is no operation sound of the motor 1-2. Check the harness/connector between the DC Controller (UN09/J13) and the Cassette 1 Lifter Motor (M14) 2-2. Check conduction of the fuse (FU2) of the DC Controller (UN09) 3-2. Check the condition of the gear at the host machine side (to see if there is something missing or swing with the gear) 4-2. Check the Cassette 1 Lifter Motor (M14) 5-2. Replace the DC Controller (UN09) |
| Error code: | E065-0000 |
| Description: | There is an error in the high-voltage output to the transfer charging assembly. An error (leakage) is detected in the high-voltage output to the primary charging assembly. |
| Remedy: | - Check if the primary charging assembly is mounted properly and also check if there is no contamination. - Check if the connector (T601, J723, J730) of the HV-DC PCB is mounted properly and also check the wiring. - Replace the HV-DC PCB. |
| Error code: | E065-0001 |
| Description: | Error in detection of abnormal M charging AC current value During the paper interval simple discharge current control, a current value that is higher than the target of 500[uA] is detected |
| Remedy: | Error in output of charging high voltage, Drum Unit error or environment control error 1. COPIER > DISPLAY > ANALOG; check if the TEMP value and the HUM value are matched with the environment temperature. When the values are dramatically mismatched (Lager than 15degrees Celsius) 2-1. Check the harness and connector between the DC Controller (UN09/ J206) and the Environment Sensor (UN45) 3-1. Replace the Environment Sensor (UN45) 4-1. Replace the DC Controller (UN9) When the values are matched 2-2. Check the state of the charging high voltage contact point 3-2. Replace the Drum Unit (M) 4-2. Check the harness and connector between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) 5-2. Replace the Primary Charging High Voltage PCB (UN06) 6-2. Replace the DC Controller PCB (UN09) |
| Error code: | E065-0002 |
| Description: | Error in detection of abnormal C charging AC current value During the paper interval simple discharge current control, a current value that is higher than the target of 500[uA] is detected |
| Remedy: | Error in output of charging high voltage, Drum Unit error or environment control error 1. COPIER > DISPLAY > ANALOG; check if the TEMP value and the HUM value are matched with the environment temperature. When the values are dramatically mismatched (Lager than 15degrees Celsius) 2-1. Check the harness and connector between the DC Controller (UN09/ J206) and the Environment Sensor (UN45) 3-1. Replace the Environment Sensor (UN45) 4-1. Replace the DC Controller (UN9) When the values are matched 2-2. Check the state of the charging high voltage contact point 3-2. Replace the Drum Unit (C) 4-2. Check the harness and connector between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) 5-2. Replace the Primary Charging High Voltage PCB (UN06) 6-2. Replace the DC Controller PCB (UN09) |
| Error code: | E065-0003 |
| Description: | Error in detection of abnormal Bk charging AC current value During the paper interval simple discharge current control, a current value that is higher than the target of 500[uA] is detected |
| Remedy: | Error in output of charging high voltage, Drum Unit error or environment control error 1. COPIER > DISPLAY > ANALOG; check if the TEMP value and the HUM value are matched with the environment temperature. When the values are dramatically mismatched (Lager than 15degrees Celsius) 2-1. Check the harness and connector between the DC Controller (UN09/ J206) and the Environment Sensor (UN45) 3-1. Replace the Environment Sensor (UN45) 4-1. Replace the DC Controller (UN9) When the values are matched 2-2. Check the state of the charging high voltage contact point 3-2. Replace the Drum Unit (Bk). 4-2. Check the harness and connector between the DC Controller PCB (UN09/ J21) and the Primary Charging High Voltage PCB (UN06/ J441, J442) 5-2. Replace the Primary Charging High Voltage PCB (UN06) 6-2. Replace the DC Controller PCB (UN09) |
| Error code: | E067-0001 |
| Description: | Error in M primary transfer abnormal detection When trying to apply the specified voltage of 1500 [V] or higher |
| Remedy: | Error in the Primary Transfer High Voltage PCB, Error in the Primary Transfer Roller (ITB Unit) 1. Check failure of the harness between the Primary Transfer High Voltage PCB (UN04/J1001) and the DC Controller PCB (UN09/J205) (open circuit, trapped cable, connector disconnection). -> Replace the harness if it is faulty 2. Check connection failure between the Primary Transfer High Voltage PCB (UN04/J31) and the Primary Transfer Roller (Check that the connection is free from open circuit or GND contact) 3. Replace the Primary Transfer High Voltage PCB (UN04) 4. Replace the ITB Unit 5. Replace the DC Controller PCB (UN09). 6. Replace the Primary Transfer Power Supply Unit |
| Error code: | E067-0002 |
| Description: | Error in C primary transfer abnormal detection When trying to apply the specified voltage of 1500 [V] or higher |
| Remedy: | Error in the Primary Transfer High Voltage PCB, Error in the Primary Transfer Roller (ITB Unit) 1. Check failure of the harness between the Primary Transfer High Voltage PCB (UN04/J1001) and the DC Controller PCB (UN09/J205) (open circuit, trapped cable, connector disconnection). -> Replace the harness if it is faulty 2. Check connection failure between the Primary Transfer High Voltage PCB (UN04/J21) and the Primary Transfer Roller (Check that the connection is free from open circuit or GND contact) 3. Replace the Primary Transfer High Voltage PCB (UN04) 4. Replace the ITB Unit 5. Replace the DC Controller PCB (UN09). 6. Replace the Primary Transfer Power Supply Unit |
| Error code: | E067-0003 |
| Description: | Error in Bk primary transfer abnormal detection When trying to apply the specified voltage of 1500 [V] or higher |
| Remedy: | Error in the Primary Transfer High Voltage PCB, Error in the Primary Transfer Roller (ITB Unit) 1.Check failure of the harness between the Primary Transfer High Voltage PCB (UN04/J1001) and the DC Controller PCB (UN09/J205) (open circuit, trapped cable, connector disconnection). -> Replace the harness if it is faulty 2. Check connection failure between the Primary Transfer High Voltage PCB (UN04/J11) and the Primary Transfer Roller (Check that the connection is free from open circuit or GND contact) 3. Replace the Primary Transfer High Voltage PCB (UN04) 4. Replace the ITB Unit 5. Replace the DC Controller PCB (UN09) 6. Replace the Primary Transfer Power Supply Unit |
| Error code: | E069-0001 |
| Description: | Abnormal current is detected at the secondary transfer When 5 [uA] or smaller is detected at the secondary transfer |
| Remedy: | Error in the Secondary Transfer High Voltage PCB, Error in the Secondary Transfer Roller 1. Check failure of the harness between the Secondary Transfer High Voltage PCB (UN05/J201) and the DC Controller PCB (UN09/J10) (open circuit, trapped cable, connector disconnection). -> Replace the harness if it is faulty 2.Check connection failure between the Secondary Transfer High Voltage PCB (UN05/T1201) and the Secondary Transfer Outer Roller (Check that the connection is free from open circuit or GND contact) 3. Replace the Secondary Transfer High Voltage PCB (UN05) 4. Replace the Secondary Transfer Outer Roller 5. Replace the ITB Unit 6. Replace the DC Controller PCB (UN09) 7. Replace the Secondary Transfer Power Supply Unit |
| Error code: | E069-0002 |
| Description: | Abnormal current is detected at the secondary transfer When 100 [uA] or larger is detected at the secondary transfer |
| Remedy: | Error in the Secondary Transfer High Voltage PCB, Error in the Secondary Transfer Roller 1. Check failure of the harness between the Secondary Transfer High Voltage PCB (UN05/J201) and the DC Controller PCB (UN09/J10) (open circuit, trapped cable, connector disconnection). -> Replace the harness if it is faulty 2. Check connection failure between the Secondary Transfer High Voltage PCB (UN05/T1201) and the Secondary Transfer Outer Roller (Check that the connection is free from open circuit or GND contact) -> Replace the connection wire if it is faulty 3. Replace the Secondary Transfer High Voltage PCB (UN05) 4. Replace the Secondary Transfer Outer Roller 5. Replace the ITB Unit 6. Replace the DC Controller PCB (UN09). |
| Error code: | E074-0000 |
| Description: | Error in the primary transfer disengagement control At the primary transfer disengagement control, the sensor fails to detect although the specified time has passed. |
| Remedy: | Error in the Primary Transfer Disengagement Solenoid, Error in the Primary Transfer Disengagement Switch, or the ITB Guide Rail error 1. Replace the ITB Unit 2. Check the harness/connector between the DC Controller PCB (UN09/J11) and the Primary Transfer Disengagement Switch (SW01) 3. Check the harness/connector between the DC Controller PCB (UN09/J11) and the Primary Transfer Disengagement Solenoid (SL01) 4. Check conduction of FU6 on the DC Controller PCB (UN09) 5. Replace the ITB Guide Rail 6. Replace the Main Drive 7. Replace the Fixing Drive 8. Replace the DC Controller PCB (UN09) |
| Error code: | E074-FFFF |
| Description: | ITB rotation detection error The sensor fails to detect although it passes through the mark on the ITB for the specified time (ITB is detected as not rotating) |
| Remedy: | The HP mark is at undetectable state, ITB Top Sensor error, or error in the coupling between the ITB Unit and the ITB Drive 1. Check if the ITB is driven. When the ITB is driven 2-1. Check soil of the HP mark on the ITB Belt 3-1. Check if there is a scar at the edge of the ITB 4-1. Use your hand to check if the shutter of the Registration Patch Sensor Unit can be open 5-1. Check for soil on the window of the Patch Sensor (UN43/ UN44) 6-1. Check movement of the Registration Shutter Solenoid (SL02) COPIER > FUNCTION > PART-CHK > SL to move SL02 7-1. Check the harness/connector between the DC Controller PCB (UN09/J12) and the Patch Sensor (UN43/J4007, UN44/ J4006) 8-1.Replace the Registration Patch Sensor Unit 9-1 Replace the ITB Unit. 10-1. Replace the DCON When the ITB is not driven 2-2. Remove and then install the ITB Unit 3-2 Replace the ITB Unit. 4-2. Replace the Main Drive |
| Error code: | E100-0001 |
| Description: | Error detection on any of scanner motor, laser unit, and BD detection at scanner area. |
| Causes: | Magenta optical assembly failure |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board. |
| Error code: | E100-0002 |
| Description: | Optical assembly error (Laser) |
| Causes: | Cyan optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E100-0003 |
| Description: | Optical assembly error (Laser) |
| Causes: | Black optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0001 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor rotation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0002 |
| Description: | Error in first artificial BD adjustment |
| Causes: | Primary pseudo BD correction |
| Error code: | E110-0003 |
| Description: | There is a scanner motor error. The FG signal is not detected while the polygon scanner is rotating stably. |
| Remedy: | Turn off the main power, and check the DC controller PCB and the 24V system fuse; then, turn on the main power. |
| Error code: | E194-0000 |
| Description: | Error in CPR sensor |
| Causes: | If CPR sensor is judged error. Cause Soiling in density detection sensor, failure in density detection sensor, failure in DC controller PCB, failure in toner cartridge. |
| Remedy: | - Check the connector of DC controller PCB - Replace the ITB unit - Replace the DC controller PCB - Replace the toner cartridge |
| Error code: | E194-0001 |
| Description: | Registration detection error When there is an image gap of 3.25[mm] or larger. |
| Remedy: | The last registration detection was not properly executed 1. Clear the registration detection data COPIER>FUNCTION>CLEAR>REG-CLR 2. Clean the window of the scanner 3. Check density on the image visually. When the image density is light 4-1. Clean the high voltage contact point with dry wiping or air blower. 5-1. Replace the Drum Unit (If the color showing abnormality can be identified from the image, replace the Drum Unit for that color. otherwise, replace from the Drum Unit (Y) in order) 6-1. Check the harness/connector between the DCON and the High Voltage PCB 7-1.Replace the High Voltage PCB. Primary Charging High Voltage PCB (UN06), Developing High Voltage PCB (UN07), Auxiliary High Voltage PCB (UN08), Primary Transfer High Voltage PCB (UN04) 8-1 Replace the DCON When the image density is not light 4-2.Use your hand to check that the shutter of the Registration Patch Sensor Unit can be open 5-2. Check for soil on the window of the Patch Sensor (UN43, UN44) 6-2.Check scar on the ITB. 7-2. Check movement of the Registration Shutter Solenoid COPIER > FUNCTION > PART-CHK > SL to move SL02 8-2. Check the harness/connector between the DC Controller PCB (UN09) and the Patch Sensor (UN43/J4007, UN44/J4006) 9-2. Replace the Registration Patch Sensor Unit 10-2 Replace the ITB Unit. |
| Error code: | E194-FFFF |
| Description: | Registration detection error There has been no command from CONT although 1 min has passed since the start of retry operation |
| Remedy: | Connection failure between the DC Controller PCB (UN09) and the CB Controller PCB (UN11), error in the DC Controller PCB (UN09), or error in the Controller PCB 1.Disconnect and then connect FFC (FFC 07) that is connected to the DC Controller PCB (UN09) and Main Controller PCB 2 (UN12) 2. Replace Main Controller PCB 2 (UN12) 3. Replace the DC Controller PCB (UN09) |
| Error code: | E196-0001 |
| Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (mainn ROM). |
| Causes: | D-con update for the optional cassette is not completed. |
| Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
| Error code: | E196-0002 |
| Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (option ROM). |
| Causes: | Can not access to DC controller NVRAM Cause Failure in DC controller PCB |
| Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
| Error code: | E196-0003 |
| Description: | Detection of noncompatible DC Controller |
| Causes: | DC Controller firmware of another model was detected. |
| Remedy: | 1. Replace the DC Controller with that of this model. 2. Update firmware. |
| Error code: | E196-1B00 |
| Description: | E2PROM communication error Command error |
| Remedy: | Turn OFF and then ON the main power |
| Error code: | E196-1B01 |
| Description: | E2PROM communication error Command error |
| Remedy: | Turn OFF and then ON the main power |
| Error code: | E196-1B02 |
| Description: | E2PROM communication error Command error |
| Remedy: | Turn OFF and then ON the main power |
| Error code: | E196-1B03 |
| Description: | E2PROM communication error Command error |
| Remedy: | Turn OFF and then ON the main power |
| Error code: | E196-1B04 |
| Description: | E2PROM communication error Command error |
| Remedy: | Turn OFF and then ON the main power |
| Error code: | E196-1BFF |
| Description: | E2PROM communication error Command error |
| Remedy: | Turn OFF and then ON the main power |
| Error code: | E197-0000 |
| Description: | Printer engine communication error Erroneous communication between the DC controller PCB and image processor PCB was detected. |
| Causes: | Internal communication error |
| Remedy: | - Check the connectors of the DC controller PCB and image processor PCB. - Replace the DC controller PCB for normal connection. - Replace the image processor PCB. |
| Error code: | E197-0050 |
| Description: | Serial communication error. Ex serial communication error with the Fixing Feed Driver PCB. |
| Remedy: | 1. Check the connection between the Fixing Feed Driver PCB (J1551) and the DC Controller PCB (J1222). 2. Replace the DC ControllerPCB. 3. Replace the Fixing Feed Driver PCB. |
| Error code: | E202-0001 |
| Description: | Reader HP sensor fault |
| Causes: | Reader HP outward fault The CCD unit moves backward, but does not move to the home position. |
| Remedy: | - Replace reader HP sensor. - Replace reader motor sensor. - Replace reader unit. |
| Error code: | E202-0002 |
| Description: | Contact Sensor HP error, Failure in return |
| Causes: | Reader HP homeward fault - Replace reader unit. The CCD unit moves forward, but does not move to the home position. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
| Error code: | E225-0001 |
| Description: | Light intensity of a lamp is less or equal to the criteria |
| Causes: | When the light intensity is at the reference level or below at shading. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board. |
| Error code: | E227-0001 |
| Description: | Reader unit power supply error When the 24 V port is OFF when the power is turned ON. |
| Remedy: | Disconnect and re-connect the power connector. Replace the power supply |
| Error code: | E227-0002 |
| Description: | Reader unit power supply error When the 24 V port is OFF when a job is started. |
| Remedy: | Disconnect and re-connect the power connector. Replace the power supply |
| Error code: | E227-0003 |
| Description: | Reader unit power supply error When the 24 V port is OFF when a job is finished. |
| Remedy: | Disconnect and re-connect the power connector. Replace the power supply |
| Error code: | E227-0004 |
| Description: | Reader unit power supply error When the 24 V port is OFF during load drive. |
| Remedy: | Disconnect and re-connect the power connector. Replace the power supply |
| Error code: | E240-0000 |
| Description: | Error in communication between main controller and DC controller Serial communication error |
| Causes: | The main controller PCB is faulty. The DC controller PCB is faulty. |
| Remedy: | Check the connector connections. Check the DC controller PCB (MAISY). Replace the No.1 main controller circuit. |
| Error code: | E240-0001 |
| Description: | Error in communication of controller There is no response when 3 sec passed since the main controller had sent the pickup request to DC controller during printing. |
| Remedy: | Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB |
| Error code: | E240-0002 |
| Description: | Error in communication between main controller and DC controllerWhen the response from the DC controller does not arrive within the prescribed period of time during printing |
| Remedy: | Check the connector connections. Check the DC controller PCB (MAISY). Replace the No.1 main controller circuit. |
| Error code: | E240-0003 |
| Description: | Error in communication of controller The engine is activated when jam occurs. |
| Remedy: | Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB |
| Error code: | E240-0004 |
| Description: | Error in communication of controller When 90 seconds pass as the pre-rotation end waiting |
| Remedy: | Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB |
| Error code: | E240-0005 |
| Description: | Error in communication of controller When 90 seconds pass as the Dhalf beginning waiting |
| Remedy: | Check connector, check connection of sub PCB in the controller box, check / replace DC controller PCB / main controller PCB |
| Error code: | E240-0006 |
| Description: | Communication data error Data access error |
| Remedy: | 1. Disconnect and then connect the FFC (FFC07) that is connected to the DC Controller PCB (UN09) and Main Controller PCB 2 (UN12) 2. Replace Main Controller PCB 2 (UN12) 3. Replace the DC Controller PCB (UN09) |
| Error code: | E240-0007 |
| Description: | Communication data error Time notification error |
| Remedy: | 1. Disconnect and then connect the FFC (FFC07) that is connected to the DC Controller PCB (UN09) and Main Controller PCB 2 (UN12) 2. Replace Main Controller PCB 2 (UN12) 3. Replace the DC Controller PCB (UN09) |
| Error code: | E246 |
| Description: | System Error |
| Causes: | System Error |
| Remedy: | Contact the sales companies. |
| Error code: | E247 |
| Description: | System Error |
| Causes: | System Error |
| Remedy: | Contact the sales companies. |
| Error code: | E248-0001 |
| Description: | EEPROM access error |
| Causes: | Error at EEPROM power-on EEPROM data cannot be read at power-on. |
| Remedy: | Replace reader unit. |
| Error code: | E248-0002 |
| Description: | EEPROM access error |
| Causes: | Error in EEPROM writing EEPROM writing cannot be performed. |
| Remedy: | Replace reader unit. |
| Error code: | E248-0003 |
| Description: | EEPROM access error |
| Causes: | Error in EEPROM reading after writing EEPROM reading cannot be performed after writing is performed. |
| Remedy: | Replace reader unit. |
| Error code: | E270-0001 |
| Description: | Failure of the front side vertical direction synchronization signal. The vertical direction synchronization signal (VSYNC) was not sent from the CMOS PCB (front side optical unit) correctly, and an image failure occurred or the operation stopped in failure. |
| Remedy: | 1. Displacement/disconnection of the connector of the optical unit (reader) 2. Displacement/disconnection of the connector of the reader controller PCB (PCB1) 3. Failure of the optical unit (reader) 4. Failure of the reader controller PCB |
| Error code: | E270-0002 |
| Description: | Failure of the horizontal/vertical direction synchronization signal. The vertical direction synchronization signal (VSYNC) was not sent due to a failure of the horizontal direction synchronization signal (HSYNC), and an image failure occurred or the operation stopped in failure. |
| Remedy: | 1. Displacement/disconnection of the connector of the optical unit (reader/DADF) 2. Displacement/disconnection of the connector of the reader controller PCB (PCB1) 3. Failure of the optical unit (reader/DADF) 4. Failure of the reader controller PCB |
| Error code: | E280-0001 |
| Description: | Reading unit communication error Reception status error |
| Remedy: | Disconnect and then connect the flexible cable. Replace the flexible cable |
| Error code: | E280-0002 |
| Description: | Reading unit communication error Reception interrupt error |
| Remedy: | Disconnect and then connect the flexible cable. Replace the flexible cable |
| Error code: | E280-0003 |
| Description: | Reading unit communication error Insufficient insertion of the reading unit connector |
| Remedy: | Disconnect and then connect the flexible cable. Replace the flexible cable |
| Error code: | E280-0004 |
| Description: | Readingunit communication error Communication error at J512 conector of the Reader Relay PBC(PCB1). |
| Remedy: | 1.Disconnect and then connect the flexible cable(Reader Relay PCB(PCB1)-Main Controller PCB(UN12) 50pin). 2.Replace the flexible cable. 3.Replace the Reader Relay PCB(PCB1). 4.Replace the Main Controller2 PCB(UN12). |
| Error code: | E301-0001 |
| Description: | Insufficient light intensity in shading |
| Causes: | Insufficient light intensity at shading. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor. (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor. (3) Replace the Contact Sensor. (4) Replace the Main Controller Board |
| Error code: | E301-0002 |
| Description: | Reading light intensity error The light intensity was at the reference level or below at paper back shading. |
| Remedy: | 1. Check that the LED of the Scanner Unit (Paper Back) is lit. 2. Check the connection between Scanner Unit (Paper Back) and LED, and check that the Cable is not opencircuit. 3. Check the connection between Reader Controller PCB and Scanner Unit (Paper Back), and check that the Cable is not open-circuit. |
| Error code: | E302-0001 |
| Description: | Shading error |
| Causes: | When the light intensity is below the reference level at shading |
| Remedy: | 1. Disconnect and then connect the Flexible Cable. 2. Replace the Flexible Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB (PCB2). |
| Error code: | E302-0002 |
| Description: | Shading error |
| Causes: | Image sampling for shading was not completed. |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Check the connection of the harness. 3. Replace the Main Controller PCB. 4. Replace the Reader Unit. |
| Error code: | E315-0007 |
| Description: | There is an error in image data. There is an error in JBIG encoding. |
| Remedy: | Turn off and then back on the power. |
| Error code: | E315-000d |
| Description: | There is an error in image data. There is an error in JBIG decoding. |
| Remedy: | Turn off and then back on the power. |
| Error code: | E315-000e |
| Description: | Image data trouble Damaged data (trouble in memory or HDD) Software decoding error |
| Remedy: | Replace the image memory (SDRAM) or HDD. |
| Error code: | E315-000f |
| Description: | Image process device error Error at MemoryCopy |
| Remedy: | 1. Turn OFF and then ON the main power 2. Check connection of Main Controller PCB 2 3. Replace Main Controller PCB 2 |
| Error code: | E315-0027 |
| Description: | There is an error in image data. Error in ROTU timeout |
| Remedy: | Replace SDRAM. Replace HDD. Replace the main controller PCB. |
| Error code: | E315-0035 |
| Description: | There is an error in image data. Error in MemFill timeout |
| Remedy: | Replace the main controller PCB. |
| Error code: | E315-0100 |
| Description: | There is an error in image data. Error in PrcOverRun |
| Remedy: | Replace the main controller PCB. |
| Error code: | E315-0500 |
| Description: | There is an error in image data. Error in device timeout [location to be detected] image process module (SCIO) [Detection timing] when there is no interruption 2 min after the operation has been started |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0501 |
| Description: | There is an error in image data. Device: abnormal termination error [location to be detected] image process module (SCIO) [Detection timing] When abnormal interruption is detected after the operation has been started. |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0510 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (SCIP) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0511 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (SCIP) [Detection timing] when abnormal interruption is detected after the operation has been detected |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0520 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (CMIP) [Detection timing] When there is no interruption 2 min after the operation has been started |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB. |
| Error code: | E315-0521 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (CMIP) [Detection timing] when abnormal interruption is detected after the operation has been detected |
| Remedy: | Check connection with DDI-S cable(RCON). Replace the main controller PCB |
| Error code: | E315-0530 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (JPEN) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently. |
| Error code: | E315-0531 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (JPEN) [Detection timing] when abnormal interruption is detected after the operation has been started. |
| Remedy: | Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently. |
| Error code: | E315-0540 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (JPDE) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently. |
| Error code: | E315-0541 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (JPDE) [Detection timing] when abnormal interruption is detected after the operation has been started |
| Remedy: | Turn OFF and then ON the power. Replace the main controller PCB if this occurs frequently. |
| Error code: | E315-0550 |
| Description: | There is an error in image data. Device: timeout error [Location to be detected] image process module (PRIP) [Detection timing] when there is no interruption 2 min after the operation has been started. |
| Remedy: | Check connection with DDI-P cable(DCON). Replace the main controller PCB. |
| Error code: | E315-0551 |
| Description: | There is an error in image data. Device: abnormal termination error [Location to be detected] image process module (PRIP) [Detection timing] when abnormal interruption is detected after the operation has been started. |
| Remedy: | Check connection with DDI-P cable(DCON). Replace the main controller PCB. |
| Error code: | E350 |
| Description: | 4th drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the 4th drawer. |
| Causes: | 3rd drawer transport clutch 2nd drawer transport sensor Feed motor PFC board Rollers |
| Remedy: | Open the feed cover. Is there paper in front of the 2nd drawer transport sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[C] ↓ → NO → 1. Check if the connector of the 2nd drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-210/225/231) ↓ → NO → 1. Check if the connectors of the (lower/middle) transport clutches are disconnected. 2. Check if the connector CN329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the (lower/middle) transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. |
| Error code: | E351-0000 |
| Description: | Main controller PCB fault |
| Causes: | Internal error of the main controller PCB Cause Main controller PCB fault. |
| Remedy: | - Check the connection of main controller PCB. - Replace main controller PCB. |
| Error code: | E354 |
| Description: | Vsg problem. Same as E353 |
| Causes: | System Error |
| Remedy: | Contact the sales companies. |
| Error code: | E355 |
| Description: | Toner density sensor problem |
| Causes: | System Error |
| Remedy: | Contact the sales companies. |
| Error code: | E400-0001 |
| Description: | Feeder communication error Checksum error |
| Remedy: | Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub). |
| Error code: | E400-0002 |
| Description: | Feeder communication error Reception status error |
| Remedy: | Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub). |
| Error code: | E400-0003 |
| Description: | Feeder communication error Reception interrupt error |
| Remedy: | Check the connections between the ADF controller PCB and main controller PCB (sub). Replace the ADF controller PCB. Replace the main controller PCB (sub). |
| Error code: | E413-0001 |
| Description: | Pressure motor trouble Pressure HP sensor OPEN |
| Remedy: | Replace the pressure motor. |
| Error code: | E413-0002 |
| Description: | Pressure motor trouble Pressure HP sensor CLOSE |
| Remedy: | Replace the pressure motor. |
| Error code: | E500-0000 |
| Description: | The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less |
| Causes: | The copier harness is faulty. (disconnected connector, open circuit) The finisher controller PCB or the copier’s DC controller PCB is faulty. |
| Error code: | E503-0002 |
| Description: | Saddle communication error When communication with the saddle stitcher is interrupted |
| Remedy: | - Check the connections between the saddle stitcher controller PCB and finisher controller PCB. - Replace the saddle stitcher controller PCB and finisher controller PCB. |
| Error code: | E505-0001 |
| Description: | Finisher backup memory error When the checksum value calculated by the CPU differs from the checksum values of the data held inside the RAM |
| Causes: | The backup RAM is faulty. |
| Remedy: | Replace the finisher controller PCB. |
| Error code: | E514-8001 |
| Description: | Bundling (forward rotation direction) error When the trailing edge fails to leave the trailing edge assist home position even when the trailing edge assist motor has been driven for 3 sec. |
| Remedy: | Replace the trailing edge assist motor (M109) and trailing edge assist home position sensor (PI109). |
| Error code: | E514-8002 |
| Description: | Bundling (forward rotation direction) error When the trailing edge fails to return to the trailing edge assist home position even when the trailing edge assist motor has been driven for 3 sec. |
| Remedy: | Replace the trailing edge assist motor (M109) and trailing edge assist home position sensor (PI109). |
| Error code: | E517-0001 |
| Description: | Decurler HP detection error (at intrusion amount control) The HP was not detected within the specified period of time (2 seconds) since the start of the decurler HP detection. |
| Remedy: | 1. Check that the cam of the Decurler Roller is installed properly. 2. Replace the Decurler Motor. 3. Replace the Buffer Driver PCB. 4. Replace the DC Controller PCB. |
| Error code: | E519-0002 |
| Description: | There is an error in the gear change motor (finisher R1/R2). The home position sensor does not go on within a specific period of time after the gear change motor has started to rotate. |
| Remedy: | 1) Check the gear change home position sensor. Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor. Is the wiring normal? 3) Check the gear change mechanism. Is there a fault? 4) Try replacing the gear change motor. Is the problem corrected? |
| Error code: | E519-8001 |
| Description: | There is an error in the gear change motor (finisher R1/R2). The home position sensor does not go off within a specific period of time after the gear change motor has started to rotate. |
| Remedy: | 1) Check the gear change home position sensor. Is the sensor normal? 2) Check the wiring between the fisher controller PCB and the gear change motor. Is the wiring normal? 3) Check the gear change mechanism. Is there a fault? 4) Try replacing the gear change motor. Is the problem corrected? |
| Error code: | E520-0001 |
| Description: | - Offset motor or finisher controller PCB failure - Offset HP sensor failure - The offset motor was driven for 1000 ms in the HP sensor approach direction, but the offset HP sensor did not turn on. |
| Remedy: | - Check the connector of the offset HP sensor. - Check the connector of the offset motor. - Replace the offset HP sensor. - Replace the offset motor. - Replace the finisher controller PCB. |
| Error code: | E520-0002 |
| Description: | - Offset motor or finisher controller PCB failure - Offset HP sensor failure - The offset motor was driven for 1000 ms in the HP sensor escape direction, but the offset HP sensor did not turn off. |
| Remedy: | - Check the connector of the offset HP sensor. - Check the connector of the offset motor. - Replace the offset HP sensor. - Replace the offset motor. - Replace the finisher controller PCB. |
| Error code: | E530-8001 |
| Description: | Alignment error When the alignment plate fails to leave the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec. |
| Remedy: | Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106). |
| Error code: | E530-8002 |
| Description: | Alignment error When the alignment plate fails to return to the alignment plate front home position sensor position even when the alignment plate front motor was driven for 4 sec. |
| Remedy: | Replace the alignment plate front motor (M103) and alignment plate front home position sensor (PI106). |
| Error code: | E531-8001 |
| Description: | Stapler error When the stapler fails to leave the stapler home position even though the stapler motor was driven for 0.5 sec. |
| Remedy: | Replace the stapler motor (M111) and stapler home position detection sensor (PI50). |
| Error code: | E531-8002 |
| Description: | Stapler error When the stapler fails to return to the stapler home position even though the stapler motor was driven for 0.5 sec. |
| Remedy: | Replace the stapler motor (M111) and stapler home position detection sensor (PI50). |
| Error code: | E532-0001 |
| Description: | There is a fault in the shift of the stapler. Finisher-N1/Saddle Finisher-N2 The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler shift base. The stapler shift base does not leave the stapler shift home position sensor when the stapler shift motor has been driven for 4 sec. |
| Causes: | The stapler shift motor (M4) is faulty. The stapler shift home position sensor (PI7) is faulty. |
| Remedy: | Replace the stapler shift HP sensor (PI50) , Replace the stapler shift motor (M35) |
| Error code: | E532-0002 |
| Description: | There is a fault in the shift of the stapler. Finisher-N1/Saddle Finisher-N2 The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler shift base. The stapler shift base does not return from the stapler shift home position sensor when the stapler shift motor has been driven for 4 sec. |
| Causes: | The stapler shift motor (M4) is faulty. The stapler shift home position sensor (PI7) is faulty. |
| Remedy: | Replace the stapler shift HP sensor (PI50) , Replace the stapler shift motor (M35) |
| Error code: | E532-8001 |
| Description: | There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go off within a specific period of time after the stapler shift motor has started to rotate. |
| Remedy: | 1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected? |
| Error code: | E532-8002 |
| Description: | There is an error in the shift mechanism of the stapler. (finisher R1/R2) The home position sensor does not go on within a specific period of time after the stapler shift motor has started to rotate. |
| Remedy: | 1) Check the stapler shift home position sensor. Is the sensor normal? 2) Check the wiring between the finisher controller PCB and the stapler shift motor. Is the wiring normal? 3) Check the path of the stapler shift base. Is there a mechanical obstacle? 4) Try replacing the stapler shift motor. Is the problem corrected? |
| Error code: | E535-8001 |
| Description: | Oscillation error When the stapler fails to leave the oscillation home position even though the oscillator motor was driven for 3 sec. |
| Remedy: | Replace the oscillator motor (M106) and oscillation home position sensor (PI105). |
| Error code: | E535-8002 |
| Description: | Oscillation error Occurs when the oscillation guide close switch fails to be set to ON even when the oscillator motor is run in the reverse direction for 1 sec. |
| Remedy: | Replace the oscillator motor (M106) and oscillation home position sensor (PI105). |
| Error code: | E537-8001 |
| Description: | Front alignment error When the alignment plate fails to leave the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec. |
| Remedy: | Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107). |
| Error code: | E537-8002 |
| Description: | Front alignment error When the alignment plate fails to return to the alignment plate back home position sensor position even though the alignment plate back motor was driven for 4 sec. |
| Remedy: | Replace the alignment plate back motor (M104) and alignment plate back home position sensor (PI107). |
| Error code: | E540-0001 |
| Description: | - Standard tray shift motor or finisher controller PCB failure - Standard tray HP sensor failure - Standard tray clock sensor failure - Standard tray shift motor load failure The standard tray was moved but the paper surface was not detected. |
| Causes: | The tray lift motor (M5) is faulty. The tray lift motor clock sensor 1/2 (PI19/PI20) is faulty. The tray home position sensor (PI8) is faulty. |
| Remedy: | - Check the connector of the standard tray HP sensor. - Check the connector of the standard tray clock sensor. - Check the connector of the standard tray shift motor. - Replace the standard tray HP sensor. - Replace the standard tray clock sensor. - Replace the standard tray shift motor. - Replace the finisher controller PCB. |
| Error code: | E540-0005 |
| Description: | - Standard tray shift motor or finisher controller PCB failure - Standard tray HP sensor failure - Standard tray clock sensor failure - Standard tray shift motor load failure The encoder clock signal was not detected two or more times when the standard tray was operated for 300 ms. |
| Remedy: | - Check the connector of the standard tray HP sensor. - Check the connector of the standard tray clock sensor. - Check the connector of the standard tray shift motor. - Replace the standard tray HP sensor. - Replace the standard tray clock sensor. - Replace the standard tray shift motor. - Replace the finisher controller PCB. |
| Error code: | E540-8001 |
| Description: | Tray up/down error - When the tray fails to return to the home position even when the 1st tray shift motor has been driven for 20 sec. - When the tray fails to move to another area even when the 1st tray shift motor has been driven for 4 sec. |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8002 |
| Description: | Tray up/down error When a danger area is reached before the sheet level is detected by the 1st tray sheet level detection sensor during the sheet level detection operation - When a discontinuous area was detected during the tray operation |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8003 |
| Description: | Tray up/down error When the input of the clock signal could not be detected within 0.2 sec. during the operation of the 1st tray shift motor |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8004 |
| Description: | Tray up/down error When the input of the clock signal could not be detected within 0.2 sec. during the operation of the 1st tray shift motor |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8005 |
| Description: | Tray up/down error When the lock detection signal was set to OFF 150 ms after the lock detection signal was set to ON |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8006 |
| Description: | Tray up/down error When the lock detection signal could not be set to ON within 1 sec. after the start of the 1st tray shift motor drive |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E540-8007 |
| Description: | Tray up/down error When the lock detection signal fails to go OFF when the 1st tray shift motor is stopped |
| Remedy: | - Check the 1st tray shift area sensor connectors. - Replace the 1st tray shift area sensor. - Replace the 1st tray shift motor (M107) |
| Error code: | E542-0001 |
| Description: | - Optional tray motor or finisher controller PCB failure - Optional tray HP sensor failure - Optional tray clock sensor failure - Optional tray shift motor load failure The optional tray was operated, but the paper surface was not detected. |
| Remedy: | - Check the connector of the optional tray HP sensor. - Check the connector of the optional tray clock sensor. - Check the connector of the optional tray shift motor. - Replace the optional tray HP sensor. - Replace the optional tray clock sensor. - Replace the optional tray shift motor. - Replace the finisher controller PCB. |
| Error code: | E542-0005 |
| Description: | - Optional tray motor or finisher controller PCB failure - Optional tray HP sensor failure - Optional tray clock sensor failure - Optional tray shift motor load failure - The encoder clock signal was not detected two or more times when the optional tray was operated for 300 ms. |
| Remedy: | - Check the connector of the optional tray HP sensor. - Check the connector of the optional tray clock sensor. - Check the connector of the optional tray shift motor. - Replace the optional tray HP sensor. - Replace the optional tray clock sensor. - Replace the optional tray shift motor. - Replace the finisher controller PCB. |
| Error code: | E542-8001 |
| Description: | Tray shift error When the tray fails to return to the home position even when the 2nd tray shift motor has been driven for 20 sec. - When the tray fails to move to another area even when the 2nd tray shift motor has been driven for 4 sec. |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8002 |
| Description: | Tray shift error - When the upper limit area is reached before the sheet level is detected by the 2nd tray sheet level detection sensor 1 during a sheet level detection operation - When a discontinuous area was detected during the tray operation - When the fact that the area ahead of the 2nd tray sheet level detection sensor 2 has been reached is detected before the sheet level is detected by the 2nd tray sheet level detection sensor 2 during an escape operation |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8003 |
| Description: | Lower tray up/down error Finisher-Z1 The safety switch is activated. |
| Remedy: | Replace the shift motor (M38) of the tray 2, Replace the shift area sensor PCB of the tray 2 |
| Error code: | E542-8004 |
| Description: | Tray shift error When the input of the clock signal could not be detected within 0.2 sec. while the 2nd tray shift motor was running |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8005 |
| Description: | Tray shift error When the lock detection signal was set to OFF 150 ms after the lock detection signal was set to ON |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8006 |
| Description: | Tray shift error When the lock detection signal could not be set to ON within 1 sec. after the 2nd tray shift motor started driving |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E542-8007 |
| Description: | Tray shift error When the lock detection signal fails to go OFF when the 2nd tray shift motor is stopped |
| Remedy: | - Check the 2nd tray shift area sensor board connectors. - Replace the 2nd tray shift area sensor board. - Replace the 2nd tray shift motor (M108). |
| Error code: | E551-8001 |
| Description: | Front Fan lock error While the front fan is rotating, this machine stops the front fan after detecting the lock signal. Then this machine retries to rotate the front fan, but lock signal is detected again, this machine displays the error. |
| Remedy: | 1. Check the Fan (M8). 2. Replace the finisher controller PCB. |
| Error code: | E551-8002 |
| Description: | Rear Fan lock error While the rear fan is rotating, this machine stops the front fan after detecting the lock signal. Then this machine retries to rotate the rear fan, but lock signal is detected again, this machine displays the error. |
| Remedy: | 1. Check the Fan (M9). 2. Replace the finisher controller PCB. |
| Error code: | E567-0001 |
| Description: | Shift Roller Release Motor fails to move from HP At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M5) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Shift Roller Release Sensor (S3) Connector is physically removed. 4. Check if the Shift Roller Release Sensor (S3) failure occurs. |
| Error code: | E567-0002 |
| Description: | Shift Roller Release Motor fails to return to HP At initial rotation, when the Motor rotates for specified period of time and cannot return to HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M5) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Shift Roller Release Sensor (S3) Connector is physically removed. 4. Check if the Shift Roller Release Sensor (S3) failure occurs. |
| Error code: | E56F- |
| Description: | Entrance Roller Release/Stopper HP Motor fails to return to HP At initial rotation, when the Motor rotates for specified period of time and cannot return to HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M6) Connector is physically removed. 2. Replace the Motor. 3. Check if the Entrance Roller Release/Stopper HP Sensor (S5) Connector is physically removed. 4. Replace the Entrance Roller Release/Stopper HP Sensor (S5). |
| Error code: | E56F-0001 |
| Description: | Entrance Roller Release/Stopper HP Motor fails to move from HP At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M6) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Entrance Roller Release/Stopper HP Sensor (S5) Connector is physically removed. 4. Check if the Entrance Roller Release/Stopper HP Sensor (S5) failure occurs. |
| Error code: | E571-0001 |
| Description: | Gripper Open/Close Motor fails to move from HP At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M7) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Gripper Arm HP Sensor (S13) Connector is physically removed. 4. Check if the Gripper Unit HP Sensor (S7) failure occurs. |
| Error code: | E571-0002 |
| Description: | Gripper Open/Close Motor fails to return to HP At initial rotation, when the Motor rotates for specified period of time and cannot return to HP, it is detected as an error if the same symptom occurs again after the first retry. |
| Remedy: | 1. Check if the Motor (M7) Connector is physically removed. 2. Check if the Motor failure occurs. 3. Check if the Gripper Arm HP Sensor (S13) Connector is physically removed. 4. Check if the Gripper Unit HP Sensor (S7) failure occurs. |
| Error code: | E575-0001 |
| Description: | - Stack delivery motor or finisher controller PCB failure - Stack delivery HP sensor failure - The stack delivery motor was driven for 2000 ms in the stack delivery direction (HP sensor approach direction), but the stack delivery HP sensor did not turn on. |
| Remedy: | - Check the connector of the stack delivery HP sensor. - Check the connector of the stack delivery motor. - Check the connector of the stack delivery HP sensor. - Replace the stack delivery motor. - Replace the finisher controller PCB. |
| Error code: | E575-0002 |
| Description: | - Stack delivery motor or finisher controller PCB failure - Stack delivery HP sensor failure - The stack delivery motor was driven for 2000 ms in the HP sensor escape direction, but the stack delivery HP sensor did not turn off. |
| Remedy: | - Check the connector of the stack delivery HP sensor. - Check the connector of the stack delivery motor. - Check the connector of the stack delivery HP sensor. - Replace the stack delivery motor. - Replace the finisher controller PCB. |
| Error code: | E584-0002 |
| Description: | - Shutter drive motor or finisher controller PCB failure - Shutter open detection sensor failure - Shutter clutch failure - The shutter open sensor did not turn off when 1000 ms have lapsed since the shutter unit had performed close operation, resulting in incomplete close operation. |
| Causes: | The feed motor (M1) is faulty. The shutter open sensor (PI5) is faulty. |
| Remedy: | - Check the connector of the shutter open sensor. - Check the connector of the shutter clutch. - Check the connector of the shutter motor. - Replace the shutter open sensor. - Replace the shutter clutch. - Replace the shutter drive motor. - Replace the finisher controller PCB. |
| Error code: | E584-8001 |
| Description: | Tray unit trouble When the shutter fails to leave the shutter home position even when the binding motor has been driven for 3 sec. |
| Remedy: | - Check the shutter home position sensor connectors. - Replace the shutter home position sensor. - Replace the shutter open/close clutch (CL101). - Replace the binding bottom roller clutch (CL102). - Replace the binding motor (M102). |
| Error code: | E5F0-8001 |
| Description: | Saddle sheet positioning error When the sheet positioning plate home position sensor fails to turn ON even when the sheet positioning plate motor is driven by 1500 pulses |
| Remedy: | - Check the sheet positioning plate home position sensor (P17) connectors. - Replace the sheet positioning plate home position sensor (P17). - Replace the sheet positioning plate motor (M4). |
| Error code: | E5F0-8002 |
| Description: | Saddle sheet positioning error When the sheet positioning plate home position sensor fails to turn OFF even when the sheet positioning plate motor is driven by 300 pulses |
| Remedy: | - Check the sheet positioning plate home position sensor (P17) connectors. - Replace the sheet positioning plate home position sensor (P17). - Replace the sheet positioning plate motor (M4). |
| Error code: | E5F1-8001 |
| Description: | Saddle sheet creasing error When the number of detection pulses of the sheet creasing motor clock sensor has dropped below the prescribed number |
| Remedy: | - Check the sheet creasing motor clock sensor (P14) and sheet creasing home position sensor (P121) connectors. - Replace the sheet creasing motor clock sensor (P14) and sheet creasing home position sensor (P121). - Replace the sheet creasing motor (M2). |
| Error code: | E5F1-8002 |
| Description: | Saddle sheet creasing error When the sheet creasing home position sensor status fails to change even when the sheet creasing motor is driven for 3 sec. |
| Remedy: | When the sheet creasing home position sensor status fails to change even when the sheet creasing motor is driven for 3 sec. |
| Error code: | E5F2-8001 |
| Description: | Saddle guide error The guide HP sensor fails to be ON after the guide motor is driven for 0.455 sec. |
| Remedy: | Replace the guide motor (M3S), Replace the guide HP sensor (PI13S) |
| Error code: | E5F2-8002 |
| Description: | Saddle guide error The HP sensor fails to be OFF after the guide motor is driven for 1 sec. |
| Remedy: | Replace the guide motor (M3S), Replace the guide HP sensor (PI13S) |
| Error code: | E5F3-8001 |
| Description: | Saddle alignment error When the alignment plate home position sensor fails to turn ON even when the alignment motor is driven for 0.5 sec. (or driven for 1.67 sec. during the initial operation) |
| Remedy: | - Check the alignment plate home position sensor (P15S) connectors. - Replace the alignment plate home position sensor (P15S). - Replace the alignment motor (M5S). |
| Error code: | E5F3-8002 |
| Description: | Saddle alignment error When the alignment plate home position sensor fails to turn OFF even when the alignment motor is driven for 1 sec. |
| Remedy: | - Check the alignment plate home position sensor (P15S) connectors. - Replace the alignment plate home position sensor (P15S). - Replace the alignment motor (M5S). |
| Error code: | E5F4-8001 |
| Description: | Saddle rear stapler error When the stitch operation home position sensor fails to turn OFF even when the stitch motor (rear) has been run in the forward direction for at least 0.5 sec. |
| Remedy: | - Check the stitch operation home position sensor (rear, MS5S) connectors. - Replace the stitch operation home position sensor (rear, MS5S). - Replace the stitch motor (rear, M6S). |
| Error code: | E5F4-8002 |
| Description: | Saddle rear stapler error When the stitch operation home position sensor fails to turn ON even when the stitch motor (rear) has been run in the reverse direction for at least 0.5 sec. |
| Remedy: | - Check the stitch operation home position sensor (rear, MS5S) connectors. - Replace the stitch operation home position sensor (rear, MS5S). - Replace the stitch motor (rear, M6S). |
| Error code: | E5F5-8001 |
| Description: | Saddle front stapler error When the stitch operation home position sensor fails to turn OFF even when the stitch motor (front) has been run in the forward direction for at least 0.5 sec. |
| Remedy: | - Check the stitch operation home position sensor (front, MS7S) connectors. - Replace the stitch operation home position sensor (front, MS7S). - Replace the stitch motor (front, M7S). |
| Error code: | E5F5-8002 |
| Description: | Saddle front stapler error When the stitch operation home position sensor fails to turn ON even when the stitch motor (front) has been run in the reverse direction for at least 0.5 sec. |
| Remedy: | - Check the stitch operation home position sensor (front, MS7S) connectors. - Replace the stitch operation home position sensor (front, MS7S). - Replace the stitch motor (front, M7S). |
| Error code: | E5F6-8001 |
| Description: | Saddle sheet push plate stapler error When the sheet push plate home position sensor fails to turn ON even when the sheet push plate motor has been run for at least 0.3 sec. |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E5F6-8002 |
| Description: | Saddle sheet push plate stapler error When the sheet push plate home position sensor fails to turn OFF even when the sheet push plate motor has been run for at least 80 ms |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E5F6-8003 |
| Description: | Saddle sheet push plate stapler error When the sheet push plate edge position sensor fails to turn OFF even when the sheet push plate motor has been run for at least 80 ms |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E5F6-8004 |
| Description: | Saddle sheet push plate stapler error When the number of pulses detected by the sheet push plate motor clock sensor has dropped below the prescribed number |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E5F6-8005 |
| Description: | Saddle sheet push plate stapler error When the sheet push plate edge position sensor fails to turn ON even when the sheet push plate motor has been run for at least 0.3 sec. |
| Remedy: | - Check the sheet push plate home position sensor (P114S) connectors. - Replace the sheet push plate home position sensor (P114S). - Replace the sheet push plate motor (M8S). |
| Error code: | E602 |
| Description: | Yellow TCR Sensor adjustment failure - TCR Sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Photoconductor Unit /C • Photoconductor Unit /M • Photoconductor Unit /Y • Toner Supply Motor Y/M (M6) • Toner Supply Motor C/K (M7) • Mechanical Control Board (PWB-M) • Controller Board (PWB-P) |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Photoconductor Unit if dirty - - 2 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23 3 Reinstall Photoconductor Unit - - 4 Change Photoconductor Unit - - 5 Change PWB-M - - 6 Change PWB-P |
| Error code: | E604-0512 |
| Description: | The image memory (SDRAM) is faulty/insufficient Memory is faulty/insufficient (512MB is required) |
| Remedy: | Add on the SDRAM |
| Error code: | E604-1024 |
| Description: | The image memory (SDRAM) is faulty/insufficient Memory is faulty/insufficient (1024MB is required) |
| Remedy: | Add on the SDRAM |
| Error code: | E604-1536 |
| Description: | The image memory (SDRAM) is faulty/insufficient Memory is faulty/insufficient (1536MB is required) |
| Remedy: | Add on the SDRAM |
| Error code: | E611-0000 |
| Description: | Rebooting repeat error due to SRAM failure, etc. Rebooting error when the SRAM data has been destroyed, the job information saved in the SRAM can no longer be read or when rebooting is otherwise repeated when the power is shut off and restored |
| Remedy: | - Clear the SRAM. - Clear the power shutdown guaranteed jobs. |
| Error code: | E613-0512 |
| Description: | Faulty/insufficient image memory (Main Controller PCB2) No necessary memory at Main Controller PCB 2 |
| Remedy: | Make the Memory capacity at Main Controller PCB 2 as indicated by 0512. |
| Error code: | E613-1024 |
| Description: | Faulty/insufficient image memory (Main Controller PCB2) No necessary memory at Main Controller PCB 2 |
| Remedy: | Make the Memory capacity at Main Controller PCB 2 as indicated by 1024. |
| Error code: | E613-1536 |
| Description: | Faulty/insufficient image memory (Main Controller PCB2) No necessary memory at Main Controller PCB 2 |
| Remedy: | Make the Memory capacity at Main Controller PCB 2 as indicated by 1536. |
| Error code: | E614 |
| Description: | Flash PCB detection error |
| Error code: | E615-0001 |
| Description: | Self test error of encryption module A self test of the Ipsec Board was conducted, and an error was detected. The encryption module is broken. |
| Remedy: | Upgrade the system after HDD format. When this error occurs, normal network communication cannot be guaranteed. |
| Error code: | E674-0001 |
| Description: | There is an error in the fax board. The fax board is detected, but communication is not possible. |
| Remedy: | Turn off the main power, and check the fax board and the main controller PCB; then, turn on the main power. If the machine fails to reset, replaced the fax board or the main controller PCB |
| Error code: | E674-0004 |
| Description: | FAX is abnormal. Modem IC access is abnormal |
| Remedy: | 1. Cable connection check 2. FAX board replacement 3. Main controller board replacement |
| Error code: | E674-0008 |
| Description: | FAX is abnormal. Port IC access is abnormal |
| Remedy: | 1. Cable connection check 2. FAX board replacement 3. Main controller board replacement |
| Error code: | E674-000C |
| Description: | FAX is abnormal. Modem IC/ port IC access is abnormal |
| Remedy: | 1. Cable connection check 2. FAX board replacement 3. Main controller board replacement |
| Error code: | E674-0010 |
| Description: | FAX is abnormal. |
| Remedy: | Main controller board replacement |
| Error code: | E674-0011 |
| Description: | FAX is abnormal. |
| Remedy: | Main controller board replacement |
| Error code: | E674-0030 |
| Description: | FAX is abnormal. Check sum error |
| Remedy: | System software download for 2 line FAX |
| Error code: | E677-0003 |
| Description: | There is an external controller error. An error has been detected by a check on the configuration when the external controller is being started up. |
| Remedy: | Turn off the main power, and check the cable; then, turn on the main power. If the machine fails to start up, re-install the system software of the external contro |
| Error code: | E710-0001 |
| Description: | IPC initializing error When the ready status fails to be established within 3 sec. after the IPC chip started up |
| Causes: | The DC controller PCB is faulty. The reader controller PCB is faulty. The machine controller PCB is faulty. |
| Remedy: | Check the cable connections. |
| Error code: | E711-0001 |
| Description: | IPC communication error When error occurrence was set 4 or more times in the error register of the IPC chip within 1.5 sec. |
| Causes: | The connector has poor connection. The ADF controller PCB is faulty. The finisher controller PCB is faulty. The DA unit PCB is faulty. The card reader PCB is faulty. |
| Remedy: | Check the cable connections. Replace the ADF controller PCB. Replace the reader controller PCB. |
| Error code: | E713-0001 |
| Description: | There is a finisher communication error. There is an error in the IC used for communication by the sorter. |
| Remedy: | Turn off the main power switch, and check the wiring of the DC controller PCB and the finisher controller PCB, and check the 24V system fuse: then, turn on the main power switch. If the machine does not reset, replace the DC controller PCB/finisher controller PCB. |
| Error code: | E713-0002 |
| Description: | Error in IPC communication When detecting CRC error at transmission. |
| Remedy: | Check the connector connected to the Finisher. |
| Error code: | E713-0003 |
| Description: | Finisher communication error 3 A large amount of data from the Finisher causes the reception buffer overflow |
| Remedy: | Turn OFF and then ON the main power?a |
| Error code: | E713-0004 |
| Description: | Finisher/printer communication error When communication between the finisher and copier was interrupted |
| Remedy: | Check the cable connections. Replace the finisher controller PCB. Replace the DC controller PCB. |
| Error code: | E713-0005 |
| Description: | Finisher communication error 5 The DC Controller sent a command to the Finisher three times, but no response was received. |
| Remedy: | 1. Check cable connection between the Finisher and the host machine. 2. Turn OFF and then ON the main power. |
| Error code: | E713-0006 |
| Description: | Finisher communication error 6 Error signal was received for 3 times in a row |
| Remedy: | Turn OFF and then ON the main power |
| Error code: | E713-0007 |
| Description: | Finisher communication error 7 Overflow of driver buffer due to many requests from the upper task before the process of the driver |
| Remedy: | Turn OFF and then ON the main power |
| Error code: | E713-0008 |
| Description: | Error in IPC communication When checksum of the received data is not correct. |
| Remedy: | Check the connector connected to the Finisher. |
| Error code: | E719-0001 |
| Description: | Error in communication with coin vendor/card reader When the coin vendor which was connected before the power was turned OFF could not be recognized when the power was turned back ON |
| Causes: | The wiring is faulty (short circuit, open circuit). The Card Reader-C1 is faulty. The coin vendor is faulty. The main controller PCB is faulty. Caution To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR. |
| Remedy: | Check the cable connections. |
| Error code: | E719-0002 |
| Description: | Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.) |
| Causes: | Erroneous communication with coin vendor (serial communication) - Disconnection from the coin vendor has been detected since communication started after confirmation of normal connection to the coin vendor (after power-on). - A serial communication error has occurred. (The serial communication error cannot be recovered.) |
| Remedy: | - Check the connection between the image processor PCB and serial PCB. - Check the connectors of the serial PCB and coin vendor for normal connection. - Replace the serial PCB. - Check the coin vendor. - Replace the image processor PCB. |
| Error code: | E719-0003 |
| Description: | There is a coin vendor error. While the unit price is being checked at startup, an error occurs in the communication with the coin vendor. |
| Remedy: | Check the cable; thereafter, reset the condition in service mode: COPIER>FUNCTION>CLEAR>ERR. |
| Error code: | E719-0004 |
| Description: | Coin vendor error The coin vendor was connected to a model that does not support the coin vendor |
| Remedy: | 1. Disconnect the coin vendor |
| Error code: | E719-0011 |
| Description: | Error in communication with coin vendor/card reader When the card reader which was connected before the power was turned OFF could not be recognized when the power was turned back ON |
| Remedy: | In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E719-0012 |
| Description: | Error in communication with coin vendor/card reader When a wire in the IPC cable connected with the card reader is broken or disconnected or when an error has occurred where IPC communication cannot be recovered |
| Remedy: | In the service mode, clear the error by selecting COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E719-0031 |
| Description: | There is a coin vendor error. Error in communication at card reader (serial) startup Communication with the card reader cannot be started at startup. |
| Remedy: | 1. Check the connection of the cable for the card reader (connector disconnected, cable cut); thereafter, reset the condition in service mode: COPIER > FUNCTION > CLEAR > ERR. 2. Execute the following items in service mode after removing the card reader, and then install the card reader again. - COPIER > FUNCTION > CLEAR > CARD - COPIER > FUNCTION > CLEAR > ERR |
| Error code: | E719-0032 |
| Description: | There is a coin vendor error. Error in communication after card reader (serial) startup Communication with the card reader is available at startup, and then becomes unavailable. |
| Remedy: | Check the connection of the cable for the card reader (connector disconnected, cable cut); thereafter, reset the condition in service mode: COPIER > FUNCTION > CLEAR > ERR. |
| Error code: | E730-1001 |
| Description: | There is a PDL software error. An initialization error has occurred. |
| Remedy: | - Execute PDL resetting. - Turn on the power once again. |
| Error code: | E730-100A |
| Description: | Printer service call |
| Error code: | E730-A006 |
| Description: | There is a PDL software error. The PDL board does not respond. A subbootable is faulty or absent. |
| Remedy: | - Execute PDL resetting. - Turn on the power once again. - Check the connection of the UFR board. - Re-install the firmware. - Replace the main controller PCB. |
| Error code: | E730-A007 |
| Description: | There is a PDL software error. There is a mismatch between the control software of the machine and the PDL control software in regard to version. |
| Remedy: | - Execute PDL resetting. - Turn on the power once again. - Execute system formatting (all), and reinstall the system. |
| Error code: | E730-B013 |
| Description: | There is a PDL software error. Corruption in the font data |
| Remedy: | - Turn on the power once again. - Re-install the Software. - Execute system formatting (all), and reinstall the system. |
| Error code: | E730-C000 |
| Description: | An error such as memory not acquired at initialization occurred. |
| Remedy: | Turn on the power again. |
| Error code: | E730-C001 |
| Description: | An error occurred when accessing the HDD. |
| Remedy: | Turn on the power again. |
| Error code: | E731-3000 |
| Description: | Image processing module failure. |
| Remedy: | Main controller board 2 replacement |
| Error code: | E731-3001 |
| Description: | Image processing module failure. |
| Remedy: | Main controller board 2 replacement |
| Error code: | E731-3002 |
| Description: | Image processing module failure. |
| Remedy: | Main controller board 2 replacement |
| Error code: | E731-3015 |
| Description: | Image processing module failure |
| Remedy: | Main controller board 2 replacement |
| Error code: | E732-0001 |
| Description: | Scanner communication error |
| Causes: | Scanner communication error |
| Remedy: | 1. Update the firmware. 2. Replace the Main Controller PCB. |
| Error code: | E732-9999 |
| Description: | There is an error in reader communication. Although a printer model, the machine is identified as a reader unit at start-up. (A copier model is started up as a printer model when the RAM is initialized.) |
| Remedy: | Turn off and then on the main power. |
| Error code: | E732-FFFF |
| Description: | Scanner communication error A network communication error in a development environment is detected. |
| Remedy: | 1.Checking network connection 2.Turn OFF and then ON the main power. |
| Error code: | E733-0000 |
| Description: | Erroneous communication between controller and printer Cannot communicate with the printer at startup. |
| Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
| Remedy: | - Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB. |
| Error code: | E733-0001 |
| Description: | Printer communication error (Invalid communication after communication is established, Parity error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-0005 |
| Description: | Printer communication error (Communication timeout error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-0006 |
| Description: | Printer communication error (Unknown communication error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-9999 |
| Description: | Printer communication error The Finisher connection information differs between the Main Controller PCB 2 and the DC Controller PCB. The information on the Main Controller PCB 2 side is overwritten by turning OFF and then ON the power. |
| Remedy: | 1. Turn OFF and then ON the power |
| Error code: | E733-F000 |
| Description: | Printer communication error A communication error between the DC Controller PCB and the Main Controller PCB 2 is detected at startup. |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Check the connection of the Flexible Cable between the DC Controller PCB (UN9) and the Main Controller PCB 2. 3. Replace the Flexible Cable |
| Error code: | E740-0002 |
| Description: | Error detection on either Network Board or Mac address |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board. |
| Error code: | E740-0003 |
| Description: | Abnormality of the Ethernet board Incorrect network ID is detected at startup. |
| Causes: | The LAN card is faulty. The main controller PCB is faulty. |
| Remedy: | Replace the Ethernet board, Replace the main controller PCB (sub LAN-bar) |
| Error code: | E743-0000 |
| Description: | Error in main controller communication An error in reading of/writing to the Flash ROM in the Main Controller occurred. |
| Causes: | Software sequence error |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. |
| Error code: | E744 |
| Description: | Stop jam at the original exit/reverse sensor |
| Causes: | Original exit/reverse sensor RADF board Perform the 05-3210 Roller Intermediate transport roller |
| Remedy: | 1. Clean the exit/reverse intermediate roller if it is stained. 2. Is the original exit/reverse sensor working? (Perform input check: 03: [FAX]/ON/[5]/[B]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN75 on the RADF board is disconnected from the original exit/reverse sensor or the harnesses are open-circuited. Correct if this is the case. 4. Replace the original exit/reverse sensor. 5. Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-356). 6. Replace the exit/reverse intermediate roller, if it is worn out. |
| Error code: | E746-0021 |
| Description: | Image analysis board self-check failure detection. |
| Remedy: | 1. Connection check of the image analysis board 2. Image analysis board replacement |
| Error code: | E746-0022 |
| Description: | Image analysis board version is invalid. |
| Remedy: | 1. Upgrading of the image analysis board software 2. Image analysis board replacement |
| Error code: | E746-0023 |
| Description: | No response from image analysis board. |
| Remedy: | 1. Connection check of the image analysis board 2. Image analysis board replacement |
| Error code: | E746-0024 |
| Description: | Image analysis board operation abnormality |
| Remedy: | 1. Connection check of the image analysis board 2. Image analysis board replacement |
| Error code: | E746-0031 |
| Description: | Hardware error (TPM) |
| Remedy: | 1. TPM board non-installation 2. Installation of TPM board from other units 3. TPM chip broken |
| Error code: | E746-0032 |
| Description: | The error that system restoration is impossible occurred (TPM) |
| Remedy: | The location of the security information in HDD/SRAM is unidentified Execute “Initialization of all data / setting” |
| Error code: | E746-0033 |
| Description: | Error occurred; but possible for system restoration (TPM) |
| Remedy: | Discrepancy of the key Execute the re-store of the TPM key |
| Error code: | E746-0034 |
| Description: | Error occurred; but possible for automatic system restoration (TPM) |
| Remedy: | Discrepancy of the key occurred. But restoration is possible when reboot. Power cycle (Power OFF/ON) |
| Error code: | E746-0035 |
| Description: | TPM version error. TPM which cannot be used in this machine was installed. |
| Remedy: | Install the supported TPM. |
| Error code: | E747-1201 |
| Description: | PDL rendering error Image processing IC error |
| Remedy: | 1. Turn OFF and then ON the power (send the data to Inc because running the data which generated an error code causes another error code) 2. Replace Main Controller PCB 2 |
| Error code: | E748-2010 |
| Description: | Flash board error |
| Remedy: | Contact each sale company bases |
| Error code: | E748-2021 |
| Description: | Main controller board 2 access errors |
| Remedy: | Main controller board 1/2 removing and inserting, replacement |
| Error code: | E748-2023 |
| Description: | Main controller board 2 access errors |
| Remedy: | DDR2-SDRAM (M0/M1/P) removing and inserting, replacement |
| Error code: | E748-2024 |
| Description: | Main controller board 2 access errors |
| Remedy: | Main controller board 1/2 removing and inserting, replacement |
| Error code: | E748-9000 |
| Description: | System error |
| Remedy: | Contact each sale company bases |
| Error code: | E749-0002 |
| Description: | Rebooting instruction due to change of MEAP configuration There is a change in configuration that requires turning OFF and then ON the power |
| Remedy: | The symptom is recovered by turning OFF and then ON the power |
| Error code: | E749-0003 |
| Description: | Booting instruction due to change in mAccele configuration There is a change in configuration that requires turning OFF and then ON the power |
| Remedy: | The symptom is recovered by turning OFF and then ON the power |
| Error code: | E749-0005 |
| Description: | Booting instruction due to change in hardware configuration There is a change in configuration that requires turning OFF and then ON the power |
| Remedy: | The symptom is recovered by turning OFF and then ON the power |
| Error code: | E749-0006 |
| Description: | Restart direction due to configuration change. The option such as the Finisher and Paper Deck was installed or removed when all of following conditions were met and the machine configuration is changed when the main power switch is turned ON. • Settings/Registration > Preferences > Timer/Energy Settings > Quick Startup at Power-on > ON • The Main Power Switch is turned OFF • The power plug of the machine is connected to the output. • The breaker is ON |
| Remedy: | It is recovered by turning OFF and then ON the main power. CAUTION This machine provides power to some PCBs even when in the main power OFF status. The power supply is not completely OFF by just turning OFF the main power switch and therefore, the machine is unable to detect a configuration change. When disconnecting and then connecting a connector, always disconnect the power plug or turn the breaker OFF. Refer to the Service Manual > Chapter 2 > External and Controls > Quick Startup for details. |
| Error code: | E750-0013 |
| Description: | Mismatch between the DC Controller PCB and the Driver PCB Error in combination of the software of the DC Controller PCB with the electrical circuit |
| Remedy: | This symptom occurs when updating the software that does not match with the DC Controller PCB 1. Check the downloaded software and then execute downloading again 2. Replace the DC Controller PCB (UN09) |
| Error code: | E753-0001 |
| Description: | Error in Finisher Boot software. The Boot software has not been written in ROM of the finisher controller. |
| Remedy: | 1. The finisher controller PCB is faulty. 2. The host machine controller PCB is faulty. |
| Error code: | E804-0000 |
| Description: | Power supply fan failure |
| Error code: | E806-0001 |
| Description: | Delivery fan error |
| Error code: | E807-0001 |
| Description: | Error in fan of process cartridge Error in fan (front) of process cartridge was detected |
| Remedy: | Check the connection of fan (front) of process cartridge, replace it |
| Error code: | E808-0001 |
| Description: | Fixing Assembly_Edge Left Cooling Fan error |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Edge Left Cooling Fan. (2) Replace the DC Controller Board. |
| Error code: | E808-0002 |
| Description: | Fixing Assembly_Edge Right Cooling Fan error |
| Causes: | Error in the Edge Right Cooling Fan (FAN2) of the Fixing Assembly |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Edge Right Cooling Fan. (2) Replace the DC Controller Board. |
| Error code: | E880-0001 |
| Description: | Controller fan1 (FM19) Error. When detect a failure of the power supply cooling fan |
| Remedy: | 1. Connector disconnection 2. Controller fan 1 (FM19) failure |
| Error code: | E996-0071 |
| Description: | Error avoidance jam (DADF). |
| Remedy: | Depending on the setting of JM-ERR-R in service mode, “010071” jam is displayed as an error. Collect log and contact to the sales companies. To cancel the setting, select COPIER> OPTION> FNCSW> J M-ERR-R, and set JM-ERR-R to 0. |
| Error code: | E996-0CA1 |
| Description: | Frequent error avoidance jam (PRINTER) |
| Remedy: | Make 000CA1 jam to be displayed as an error by setting JM-ERR-D in service mode. Collect log and contact to the sales companies. To cancel the setting, select COPIER> OPTION> FNCSW> JM-ERR-D, and set JM-ERR-D to 0. |
| Error code: | E996-0CA2 |
| Description: | Frequent error avoidance jam (PRINTER) Error avoidance jam (PRINTER) |
| Remedy: | Make 000CA2 jam to be displayed as an error by setting JM-ERR-D in service mode. Collect log and contact to the sales companies. To cancel the setting, select COPIER> OPTION> FNCSW> JM-ERR-D, and set JM-ERR-D to 0. |
| Error code: | E996-0CA3 |
| Description: | Frequent error avoidance jam (PRINTER) |
| Remedy: | Make 000CA3 jam to be displayed as an error by setting JM-ERR-D in service mode. Collect log and contact to the sales companies. To cancel the setting, select COPIER> OPTION> FNCSW> JM-ERR-D, and set JM-ERR-D to 0. |
| Error code: | E996-0CF1 |
| Description: | Frequent error avoidance jam (PRINTER) |
| Remedy: | Make “000CF1” jam to be displayed as an error by setting M-ERR-D in service mode. Collect log and contact to the sales companies. To cancel the setting, select COPIER> OPTION> FNC-SW> J M-ERR-D, and set JM-ERR-D to 0. |
Название
Canon C-EXV34 Тонер-картридж черный
Canon C-EXV34 Тонер-картридж голубой
Canon C-EXV34 Тонер-картридж пурпурный
Canon C-EXV34 Тонер-картридж желтый
Canon C-EXV34 Блок фотобарабана черный
Canon C-EXV34 Блок фотобарабана голубой
Canon C-EXV34 Блок фотобарабана пурпурный
Canon C-EXV34 Блок фотобарабана желтый
Canon C-EXV34 Контейнер для отработанного тонера
