Canon imageRUNNER Advance C3330i
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Скорость печати
A4
30
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Макс. формат |
A3 |
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Размещение |
напольный |
Тип устройства |
МФУ |
Копир |
|
Сканер |
|
Цветность печати |
цветная |
Факс |
|
Телефон |
|
Печать фотографий |
|
Принтер |
|
Макс, длина отпечатка |
457 |
Макс, ширина отпечатка |
305 |
Время разогрева |
34 |
Количество цветов |
4 |
Двусторонняя печать |
|
Прямая печать |
|
Печать без полей |
|
Система непрерывной подачи чернил |
|
Пигментные чернила |
|
Макс, разрешение для ч/б печати |
|
| По X | 1 200 |
| По Y | 1 200 |
Скорость ч/б печати |
|
| A4 | 30 |
Время выхода первого отпечатка |
|
| Ч/б | 10 |
| Цветн, | 10 |
Копир |
|
Шаг масштабирования |
0,01 |
Время выхода первой копии |
8,2 |
Макс, количество копий за цикл |
999 |
Значение масштаба |
|
| Максимальное | 4 |
| Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
| По Y | 600 |
| По X | 600 |
Скорость ч/б копирования |
|
| A3 | 15 |
Сканер |
|
Устройство автоподачи оригиналов |
двустороннее |
Макс. формат оригинала |
A3 |
Тип сканера |
планшетный |
Слайд-адаптер |
|
Емкость устройства автоподачи оригиналов |
100 |
Стандарт WIA |
|
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Макс, размер сканирования |
|
| По Y | 432 |
| По X | 297 |
Разрешение сканера |
|
| По Х | 600 |
Скорость сканирования |
|
| Ч/б | 30 |
| Цветн, | 30 |
Расходные материалы |
|
Количество картриджей |
4 |
Ресурс цветного картриджа/тонера |
19 000 |
Ресурс ч/б картриджа/тонера |
36 000 |
Печать на: |
|
| Пленках |
|
| Этикетках |
|
| Матовой бумаге |
|
| Конвертах |
|
| Карточках |
|
| Глянцевой бумаге |
|
| Фотобумаге |
|
| Рулоне |
|
| CD/DVD |
|
Плотность бумаги |
|
| Минимальная | 52 |
| Максимальная | 256 |
Факс |
|
Цветной |
|
PC Fax |
|
Телефон |
|
Автоответчик |
|
Caller ID |
|
АОН |
|
Стандарт DECT |
|
Спикерфон |
|
Беспроводная трубка |
|
Проводная трубка |
|
Шрифты и языки управления |
|
Языки управления |
|
| PPDS |
|
| PostScript 2 |
|
|
|
|
| PostScript |
|
| PostScript 3 |
|
| PCL 6 |
|
| PCL 5e |
|
| PCL 5c |
|
Количество установленных шрифтов |
|
| PostScript | 136 |
| PCL | 93 |
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Максимальная | 2 300 |
| Стандартная | 1 200 |
Вывод бумаги |
|
| Стандартный | 250 |
Финишер |
|
Степлер |
|
Сортер |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Брошюровщик |
|
Интерфейсы |
|
Версия USB |
2,0 |
AirPrint |
|
Устройство для чтения карт памяти |
|
Веб-интерфейс |
|
RS-232 |
|
Инфракрасный порт |
|
LPT |
|
Bluetooth |
|
Wi-Fi 802.11n |
|
Wi-Fi |
|
FireWire (IEEE 1394) |
|
USB |
|
Ethernet (RJ-45) |
|
Память/Процессор |
|
Макс, объем памяти |
2 048 |
Емкость жесткого диска |
250 |
Объем памяти |
1 024 |
Частота процессора |
1 670 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Диагональ дисплея |
7 |
Экран |
|
Поддержка ОС |
|
| DOS |
|
| Mac OS |
|
| Windows |
|
| Linux |
|
Потребляемая мощность |
|
| В режиме ожидания | 53 |
| При работе | 1 500 |
Уровень шума |
|
| В режиме ожидания | 14 |
| При работе | 49 |
Габариты |
|
Вес |
71,2 |
Глубина |
693 |
Ширина |
565 |
Высота |
878 |
Модули
910A POWER SUPPLY ASSEMBLY(100V,120V)
B10 INTERNAL COMPONENTS(ADF)
111D RIGHT DOOR ASSEMBLY(AU,SG,HK,TW,IN,CN,KR,230V LTN)
104D INTERNAL COMPONENTS 4(US,CA,120V LTN)
260 REGISTRATION DRIVE ASSEMBLY
191 FRONT FAN ASSEMBLY
140C POWER CORD TERMINAL ASSEMBLY(120V)
106G MACHINE REAR PLATE 1(C3330 US,CA,120V LTN)
192 REAR FAN ASSEMBLY
250 MAIN DRIVE ASSEMBLY
310 PAPER PICK-UP ASSEMBLY(SMALL)(SMALL CASSETTE)
261 PAPER PICK-UP DRIVE ASSEMBLY
271 BOTTLE DRIVE ASSEMBLY, C, K
290 LIFTER DRIVE ASSEMBLY
B41 ( 1 / 2 ) PAPER FEED ASSEMBLY(ADF)
B41 ( 2 / 2 ) PAPER FEED ASSEMBLY(ADF)
330B MULTI PAPER PICK-UP TRAY ASSY(US,CA,120V LTN)
320 REGISTRATION ASSEMBLY
H30 CASSETTE ASSEMBLY(SMALL)(SMALL CASSETTE)
263 REVERSE DUPLEXING DRIVE ASSY
112 RIGHT DOOR ASSEMBLY, LOWER
330D MULTI PAPER PICK-UP TRAY ASSY(AU,SG,TW,CN,KR,230V LTN)
111B RIGHT DOOR ASSEMBLY(US,CA,120V LTN)
981 2ND TRANSFER H.V. PCB ASSEMBLY
B12 PAPER PICK-UP COVER ASSY(ADF)
931 DC CONTROLLER PCB ASSEMBLY
100D ( 1 / 2 ) EXTERNAL COVERS, PANELS, ETC.(C3330)
530 INTER. TRANSFER BELT ASSY
106H MACHINE REAR PLATE 1(C3325 US,CA,120V LTN)
100D ( 2 / 2 ) EXTERNAL COVERS, PANELS, ETC.(C3330)
810B FIXING ASSEMBLY, FX-202(120V)
910B POWER SUPPLY ASSEMBLY(230V)
B01 MOUNTING HARDWARE
M30 SECOND PAPER DELIVERY ASSEMBLY(2/3 DELIVERY)
262 VERTICAL PATH DRIVE ASSEMBLY
B90 ADF CONTROLLER PCB ASSEMBLY(ADF)
105 INTERNAL COMPONENTS 5
107 MACHINE REAR PLATE 2
B11 BASE ASSEMBLY(ADF)
400E READER ASSEMBLY
100E ( 2 / 2 ) EXTERNAL COVERS, PANELS, ETC.(C3325)
980 PRIMARY TRANSFER H.V. ASSEMBLY
B13 DOCUMENT TRAY ASSEMBLY(ADF)
103 INTERNAL COMPONENTS 3
130D CONTROL PANEL ASSEMBLY(C3330 US,CA,AU,SG,HK,IN,LTN)
772 WASTE TONER FEED DRIVE ASSY
102B INTERNAL COMPONENTS 2
311 PAPER PICK-UP ASSEMBLY(LARGE)
280 FIXING DRIVE ASSEMBLY
130E CONTROL PANEL ASSEMBLY(C3325 US,CA,AU,SG,HK,IN,LTN)
270 BOTTLE DRIVE ASSEMBLY, Y, M
460 LASER SCANNER ASSEMBLY
350B FIRST PAPER DELIVERY ASSEMBLY(2/3 DELIVER)
930A MAIN CONTROLLER PCB ASSEMBLY(C3330 SERIES)
104E INTERNAL COMPONENTS 4(EUR,230V LTN)
140F POWER CORD TERMINAL ASSEMBLY(230V)
190 POWER SUPPLY FAN ASSEMBLY
332 DUPLEXING GUIDE ASSEMBLY
M31 THIRD PAPER DELIVERY ASSEMBLY(2/3 DELIVERY)
101E INTERNAL COMPONENTS 1
106Q MACHINE REAR PLATE 1(C3330 230V LTN)
100E ( 1 / 2 ) EXTERNAL COVERS, PANELS, ETC.(C3325)
930B MAIN CONTROLLER PCB ASSEMBLY(C3325 SERIES)
H31 CASSETTE ASSEMBLY(LARGE)
771 WASTE TONER FEED ASSEMBLY
331 MULTI PAPER PICK-UP ASSEMBLY
640 DEVELOPING ASSEMBLY
770 CONTAINER, WASTE TONER, WT-202
106R MACHINE REAR PLATE 1(C3325 230V LTN)
Детали 101E INTERNAL COMPONENTS 1
| Деталь: | SUPPORT, POWER SUPPLY |
| Парткод: | FE3-0820-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | POWER SUPPLY ASSEMBLY |
| Парткод: | FM1-A616-000 |
| Деталь: | COVER, HINGE BLANKING |
| Парткод: | FC9-6192-010 |
| Деталь: | SCREW,RS,M4X8 |
| Парткод: | XA9-0732-010 |
| Деталь: | SCREW,RS,M3X6.5 |
| Парткод: | XA9-1164-000 |
| Деталь: | LABEL, CLEANING |
| Парткод: | FE3-5521-000 |
| Деталь: | LABEL, PROHIBITION DOCUMENT |
| Парткод: | FE3-5518-000 |
| Деталь: | LABEL, DOCUMENT SIZE |
| Парткод: | FE3-0468-000 |
| Деталь: | LABEL,FINGER NIP CAUTION |
| Парткод: | FE3-5531-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FE3-5534-000 |
| Деталь: | HINGE, LEFT |
| Парткод: | FE3-5484-000 |
| Деталь: | CUSHION |
| Парткод: | FL0-1437-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FL0-1446-000 |
| Деталь: | COVER, REAR |
| Парткод: | FL0-1447-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FL0-1448-000 |
| Деталь: | PANEL, COPYBOARD |
| Парткод: | FL0-2756-000 |
| Деталь: | CABLE, I/F |
| Парткод: | FM1-G895-000 |
| Деталь: | CABLE, CONNECTING |
| Парткод: | FM1-G903-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-008 |
| Деталь: | RIGHT HINGE ASSEMBLY |
| Парткод: | FM1-D476-000 |
| Деталь: | COVER, STAMP |
| Парткод: | FC8-6311-000 |
| Деталь: | HOLDER, TRAY SUPPORT |
| Парткод: | FC8-6387-000 |
| Деталь: | HOLDER, FEEDER SHAFT |
| Парткод: | FC8-6388-000 |
| Деталь: | SHEET, READ 2 LEAD |
| Парткод: | FC8-6405-000 |
| Деталь: | SHEET, PAPER FEED |
| Парткод: | FC8-6422-000 |
| Деталь: | SHEET, PAPER FEED |
| Парткод: | FC8-6423-000 |
| Деталь: | LABEL, HINGE CAUTION |
| Парткод: | FU7-8223-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6817-000 |
| Деталь: | CORE, RING |
| Парткод: | WE8-6818-000 |
| Деталь: | INTERNAL COMPONENTS |
| Парткод: | NPN |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | LINK, MULTI PAPER PICK-UP TRAY |
| Парткод: | FE3-0438-000 |
| Деталь: | LATCH |
| Парткод: | FE3-1414-000 |
| Деталь: | ROLLER, 2ND TRNSFR. OUTER |
| Парткод: | FE3-4783-000 |
| Деталь: | LATCH, FRONT |
| Парткод: | FE3-5602-000 |
| Деталь: | LATCH, REAR |
| Парткод: | FE3-5603-000 |
| Деталь: | COVER, HANDLE |
| Парткод: | FE3-5643-000 |
| Деталь: | RAIL, STOPPER, FRONT |
| Парткод: | FE3-9572-000 |
| Деталь: | RAIL, STOPPER, REAR |
| Парткод: | FE3-9573-000 |
| Деталь: | PLATE, HANDLE GROUNDING |
| Парткод: | FE3-9574-000 |
| Деталь: | HOLDER, DUPLEXING GEAR |
| Парткод: | FE3-9804-000 |
| Деталь: | CLAMP, GEAR HOLDER |
| Парткод: | FE3-9805-000 |
| Деталь: | STOPPER, DUPLEXING, FRONT |
| Парткод: | FE4-1749-000 |
| Деталь: | STOPPER, DUPLEXING, REAR |
| Парткод: | FE4-1750-000 |
| Деталь: | RACK, DAMPER |
| Парткод: | FE4-1755-000 |
| Деталь: | SLIDER |
| Парткод: | FE4-1970-000 |
| Деталь: | ROLLER, REEL |
| Парткод: | FE4-2084-000 |
| Деталь: | ROLLER, DUPLEXING |
| Парткод: | FL0-3979-000 |
| Деталь: | SHEET |
| Парткод: | FL0-4784-000 |
| Деталь: | DUPLEXING REVERSE GEAR ASSY |
| Парткод: | FM1-B207-000 |
| Деталь: | ROLLER, DRIVEN ROLLER |
| Парткод: | FC0-7610-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FE3-1417-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE3-6162-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-9579-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0218-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1030-000 |
| Деталь: | PULLEY, 21T |
| Парткод: | FU2-0184-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0185-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0852-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1074-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1613-140 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | RIGHT DOOR ASSEMBLY |
| Парткод: | FM1-B205-000 |
| Деталь: | PLATE, FIXING FIXED |
| Парткод: | FE3-1342-000 |
| Деталь: | PLATE, FIXING POSITIONING |
| Парткод: | FE3-0837-000 |
| Деталь: | PLATE, ADJUST |
| Парткод: | FE4-0262-000 |
| Деталь: | BUSHING |
| Парткод: | FE4-1488-000 |
| Деталь: | FIXING DRAWER ASSEMBLY |
| Парткод: | FM1-B665-000 |
| Деталь: | TRAY DUCT ASSEMBLY, LOWER |
| Парткод: | FM1-G730-000 |
| Деталь: | ROWEL BLOCK ASSEMBLY |
| Парткод: | FM1-G731-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0148-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | REGISTRATION DRIVE ASSEMBLY |
| Парткод: | FM1-B200-000 |
| Деталь: | LEVER, LOCK |
| Парткод: | FC0-6580-000 |
| Деталь: | ARM, INTERLOCK, 1 |
| Парткод: | FE3-0817-000 |
| Деталь: | ARM, INTERLOCK, 2 |
| Парткод: | FE3-0849-000 |
| Деталь: | FAN |
| Парткод: | FK4-0636-000 |
| Деталь: | CABLE, INTERLOCK SWITCH |
| Парткод: | FM1-D831-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1068-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, 9P |
| Парткод: | VS1-7177-009 |
| Деталь: | FRONT FAN ASSEMBLY |
| Парткод: | NPN |
| Деталь: | CORD, POWER SUPPLY, 120V |
| Парткод: | FK3-2045-000 |
| Деталь: | CABLE, INLET |
| Парткод: | FM1-D848-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | WASHER, TOOTHED LOCK, M4 |
| Парткод: | XD1-4200-402 |
| Деталь: | POWER CORD TERMINAL ASSEMBLY |
| Парткод: | NPN |
| Деталь: | LABEL, QUICK START CAUTION |
| Парткод: | FE3-9859-000 |
| Деталь: | CABLE, SATA POWER |
| Парткод: | FK4-0275-000 |
| Деталь: | CABLE, SATA SIGNAL |
| Парткод: | FK4-0276-000 |
| Деталь: | HARD DISK DRIVE, MQ01ABF032 |
| Парткод: | FK4-1550-000 |
| Деталь: | SWITCH, PUSH |
| Парткод: | WC2-5806-000 |
| Деталь: | DEVELOPING H.V. GUIDE ASSEMBLY |
| Парткод: | FM1-B217-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, C |
| Парткод: | FM1-B218-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, BK |
| Парткод: | FM1-B219-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, Y |
| Парткод: | FM1-B220-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, M |
| Парткод: | FM1-B221-000 |
| Деталь: | INTERLOCK SWITCH ASSEMBLY |
| Парткод: | FM1-B227-000 |
| Деталь: | MULTI REEL ASSEMBLY |
| Парткод: | FM1-C283-000 |
| Деталь: | CABLE, AC DRIVER |
| Парткод: | FM1-D811-000 |
| Деталь: | CABLE, HEATER |
| Парткод: | FM1-D815-000 |
| Деталь: | CABLE, DDIP |
| Парткод: | FM1-D818-000 |
| Деталь: | CABLE, FEED |
| Парткод: | FM1-D824-000 |
| Деталь: | CABLE, PICK-UP |
| Парткод: | FM1-D827-000 |
| Деталь: | CABLE, ECO-ID |
| Парткод: | FM1-D841-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | CONNECTOR, SNAP TIGHT, W |
| Парткод: | VS1-7440-011 |
| Деталь: | CONNECTOR, SNAP TIGHT, W |
| Парткод: | VS1-7504-015 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | DAMPER, CUSHION |
| Парткод: | XH9-0149-000 |
| Деталь: | SPACER |
| Парткод: | XZ1-1301-005 |
| Деталь: | MACHINE REAR PLATE 1 |
| Парткод: | NPN |
| Деталь: | FAN |
| Парткод: | FK2-2064-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | REAR FAN ASSEMBLY |
| Парткод: | NPN |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FE3-4887-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK4-0641-000 |
| Деталь: | MOTOR, DC BRUSHLESS |
| Парткод: | FK4-0800-000 |
| Деталь: | MOTOR, DC BRUSHLESS |
| Парткод: | FK4-0809-000 |
| Деталь: | CABLE, MAIN DRIVE |
| Парткод: | FM1-D835-000 |
| Деталь: | CABLE, SENSOR |
| Парткод: | FM1-D849-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | MAIN DRIVE ASSEMBLY |
| Парткод: | FM1-A611-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5888-000 |
| Деталь: | COUPLING |
| Парткод: | FC0-7669-000 |
| Деталь: | LEVER, PAPER DETECT |
| Парткод: | FC0-7670-000 |
| Деталь: | HOLDER, SWING |
| Парткод: | FE3-0436-000 |
| Деталь: | GUIDE, VERTICAL PATH, UPPER |
| Парткод: | FE3-1500-000 |
| Деталь: | ARM |
| Парткод: | FE3-1558-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FE3-1586-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE3-1595-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-1617-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-1619-000 |
| Деталь: | LEVER, LATCH |
| Парткод: | FE3-1650-000 |
| Деталь: | GEAR, 26T |
| Парткод: | FE3-3590-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FE3-4861-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-5669-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-6168-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-6170-000 |
| Деталь: | GUIDE, VERTICAL PATH, LOWER |
| Парткод: | FE3-6429-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FE3-7684-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-7685-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE4-0215-000 |
| Деталь: | LEVER, ESTRANGEMENT |
| Парткод: | FE4-1504-000 |
| Деталь: | LIMITTER, TORQUE |
| Парткод: | FE4-1528-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE4-1660-000 |
| Деталь: | HOLDER, PAPER PICK-UP ROLLER |
| Парткод: | FE4-8286-000 |
| Деталь: | SHEET, GUIDE |
| Парткод: | FL0-1161-000 |
| Деталь: | ONE-WAY CLUTCH ASSEMBLY |
| Парткод: | FL0-1515-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-1516-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1674-000 |
| Цена: | 5 000 ₽ |
| Деталь: | ROLLER, EXTRACTION |
| Парткод: | FL0-1834-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-2885-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FL0-3191-000 |
| Деталь: | SHAFT, PAPER PICK-UP |
| Парткод: | FL0-3632-000 |
| Деталь: | HOLDER, SEPARATION ROLLER |
| Парткод: | FL0-3633-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-4002-000 |
| Цена: | 4 900 ₽ |
| Деталь: | GUIDE, SLIDE |
| Парткод: | FL0-6486-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-B236-000 |
| Деталь: | CABLE, CASSETTE SENSOR |
| Парткод: | FM1-D828-000 |
| Деталь: | BUSHING |
| Парткод: | FS1-1205-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU2-0248-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU2-0449-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0451-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1069-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-1414-000 |
| Деталь: | CONNECTOR, 9P |
| Парткод: | VS1-7177-009 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | PAPER PICK-UP ASSEMBLY |
| Парткод: | FM1-B500-000 |
| Деталь: | PAPER PICK-UP DRIVE ASSEMBLY |
| Парткод: | FM1-B201-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7440-002 |
| Деталь: | BOTTLE DRIVE ASSEMBLY, C, K |
| Парткод: | FM1-B255-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | LIFTER DRIVE ASSEMBLY |
| Парткод: | FM1-B199-000 |
| Деталь: | DIAL, JAM |
| Парткод: | FC0-9097-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FC8-6372-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FC8-6377-000 |
| Деталь: | FLANGE, PULLEY |
| Парткод: | FC8-6379-000 |
| Деталь: | CLIP |
| Парткод: | FC8-6380-000 |
| Деталь: | ROLLER, BELT TENSION |
| Парткод: | FC8-6382-000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FC8-6396-000 |
| Деталь: | JOINT, READ PULLEY |
| Парткод: | FC8-6418-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FC8-6421-000 |
| Деталь: | PULLEY, 32T/36T/GEAR, 28T |
| Парткод: | FE3-5403-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FE3-5404-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FE3-5408-000 |
| Деталь: | GEAR, 19T |
| Парткод: | FE3-5409-000 |
| Деталь: | GEAR, 39T |
| Парткод: | FE3-5410-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE3-5414-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5469-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE3-5470-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE3-5485-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE3-5514-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FE3-5528-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FE3-5540-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK3-2679-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK4-1290-000 |
| Деталь: | GUIDE, PLATEN |
| Парткод: | FL0-1438-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FL0-1441-000 |
| Деталь: | FLAPPER |
| Парткод: | FL0-2759-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE3-5415-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-5419-000 |
| Деталь: | GUIDE, REVERSE |
| Парткод: | FL0-3232-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-D471-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FE3-5413-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5416-000 |
| Деталь: | LEVER |
| Парткод: | FE3-5418-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1428-000 |
| Деталь: | BEARING, BALL, DDLF-1280ZZH |
| Парткод: | XG9-0820-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5507-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU9-0931-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-5402-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1606-440 |
| Деталь: | PULLEY, 25T/GEAR, 25T |
| Парткод: | FE3-5459-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | LINK, SOLENOID |
| Парткод: | FC8-6381-000 |
| Деталь: | SOLENOID |
| Парткод: | FK2-6871-000 |
| Деталь: | ROLLER, WHITE |
| Парткод: | FC0-9124-000 |
| Деталь: | SPACER, READ, REAR |
| Парткод: | FC8-6376-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE2-1919-000 |
| Деталь: | ARM, PLATEN, FRONT |
| Парткод: | FE3-5481-000 |
| Деталь: | SPACER, READ, FRONT |
| Парткод: | FC8-6375-000 |
| Деталь: | ARM, PLATEN, REAR |
| Парткод: | FE2-1918-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-0452-000 |
| Деталь: | GUIDE, PLATEN |
| Парткод: | FL0-2757-000 |
| Деталь: | BUSHING |
| Парткод: | FS6-1140-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0935-000 |
| Деталь: | GEAR, 48T/62T |
| Парткод: | FU9-0937-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1088-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1089-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2659-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2660-000 |
| Деталь: | PULLEY, 36T |
| Парткод: | FU8-0310-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0312-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0313-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU8-0314-000 |
| Деталь: | GEAR, 32T |
| Парткод: | FU8-0317-000 |
| Деталь: | SCREW,RS,M3X6.5 |
| Парткод: | XA9-1164-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1605-040 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0333-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0334-000 |
| Деталь: | PAPER FEED ASSEMBLY |
| Парткод: | FM1-C225-000 |
| Деталь: | DIAL, JAM |
| Парткод: | FC0-9097-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FC8-6372-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FC8-6377-000 |
| Деталь: | FLANGE, PULLEY |
| Парткод: | FC8-6379-000 |
| Деталь: | CLIP |
| Парткод: | FC8-6380-000 |
| Деталь: | ROLLER, BELT TENSION |
| Парткод: | FC8-6382-000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FC8-6396-000 |
| Деталь: | JOINT, READ PULLEY |
| Парткод: | FC8-6418-000 |
| Деталь: | BELT, TIMING |
| Парткод: | FC8-6421-000 |
| Деталь: | PULLEY, 32T/36T/GEAR, 28T |
| Парткод: | FE3-5403-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FE3-5404-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FE3-5408-000 |
| Деталь: | GEAR, 19T |
| Парткод: | FE3-5409-000 |
| Деталь: | GEAR, 39T |
| Парткод: | FE3-5410-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE3-5414-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5469-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE3-5470-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE3-5485-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE3-5514-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FE3-5528-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FE3-5540-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK3-2679-000 |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | FK4-1290-000 |
| Деталь: | GUIDE, PLATEN |
| Парткод: | FL0-1438-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FL0-1441-000 |
| Деталь: | FLAPPER |
| Парткод: | FL0-2759-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE3-5415-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-5419-000 |
| Деталь: | GUIDE, REVERSE |
| Парткод: | FL0-3232-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-D471-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FE3-5413-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5416-000 |
| Деталь: | LEVER |
| Парткод: | FE3-5418-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1428-000 |
| Деталь: | BEARING, BALL, DDLF-1280ZZH |
| Парткод: | XG9-0820-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5507-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU9-0931-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-5402-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1606-440 |
| Деталь: | PULLEY, 25T/GEAR, 25T |
| Парткод: | FE3-5459-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | LINK, SOLENOID |
| Парткод: | FC8-6381-000 |
| Деталь: | SOLENOID |
| Парткод: | FK2-6871-000 |
| Деталь: | ROLLER, WHITE |
| Парткод: | FC0-9124-000 |
| Деталь: | SPACER, READ, REAR |
| Парткод: | FC8-6376-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE2-1919-000 |
| Деталь: | ARM, PLATEN, FRONT |
| Парткод: | FE3-5481-000 |
| Деталь: | SPACER, READ, FRONT |
| Парткод: | FC8-6375-000 |
| Деталь: | ARM, PLATEN, REAR |
| Парткод: | FE2-1918-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-0452-000 |
| Деталь: | GUIDE, PLATEN |
| Парткод: | FL0-2757-000 |
| Деталь: | BUSHING |
| Парткод: | FS6-1140-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0935-000 |
| Деталь: | GEAR, 48T/62T |
| Парткод: | FU9-0937-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1088-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1089-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2659-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2660-000 |
| Деталь: | PULLEY, 36T |
| Парткод: | FU8-0310-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0312-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0313-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU8-0314-000 |
| Деталь: | GEAR, 32T |
| Парткод: | FU8-0317-000 |
| Деталь: | SCREW,RS,M3X6.5 |
| Парткод: | XA9-1164-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1605-040 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0333-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0334-000 |
| Деталь: | PAPER FEED ASSEMBLY |
| Парткод: | FM1-C225-000 |
| Деталь: | COVER,MULTI PAPER PICK-UP TRAY |
| Парткод: | FE3-1542-000 |
| Деталь: | FLAG, LENGTH SENSOR |
| Парткод: | FE3-1638-000 |
| Деталь: | TRAY, MULTI PAPER PICK-UP SUB |
| Парткод: | FE3-3606-000 |
| Деталь: | HOOK, MULTI FEED TRAY |
| Парткод: | FE3-5650-000 |
| Деталь: | LABEL, MULTI FULL |
| Парткод: | FE3-9856-000 |
| Деталь: | PAPER WIDTH SENSING PCB ASSY |
| Парткод: | FM1-C998-000 |
| Деталь: | CABLE, MULTI PAPER PICK-UP |
| Парткод: | FM1-D829-000 |
| Деталь: | GEAR, 48T |
| Парткод: | FU2-0216-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1067-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1071-000 |
| Деталь: | GEAR, 40T/47T |
| Парткод: | FU2-1075-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | LABEL, FEED MULTIPLE |
| Парткод: | FE3-9834-000 |
| Деталь: | MULTI PAPER PICK-UP TRAY ASSY |
| Парткод: | FM1-B211-000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FE4-0470-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE4-1026-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE4-1027-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-1516-000 |
| Деталь: | SHEET |
| Парткод: | FL0-4706-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0088-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0174-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-7050-000 |
| Деталь: | REGISTRATION ASSEMBLY |
| Парткод: | FM1-A625-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FC8-4990-000 |
| Деталь: | PLATE, FREE STOP |
| Парткод: | FE2-0026-010 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-0483-000 |
| Деталь: | COVER, CASSETTE FRONT |
| Парткод: | FE3-1507-000 |
| Деталь: | GEAR, 68T/37T |
| Парткод: | FE3-1527-000 |
| Деталь: | ROLLER, CASSETTE |
| Парткод: | FE3-1528-000 |
| Деталь: | LINK, SIZE DETECT |
| Парткод: | FE3-1613-000 |
| Деталь: | SHAFT, SUPPORT |
| Парткод: | FE3-5683-000 |
| Деталь: | RACK, LINK |
| Парткод: | FE3-7697-000 |
| Деталь: | PIN, ARM |
| Парткод: | FE3-8283-000 |
| Деталь: | SHAFT, DAMPER |
| Парткод: | FE3-8418-000 |
| Деталь: | ARM, GUIDE |
| Парткод: | FE4-1502-000 |
| Деталь: | PIN, GUIDE |
| Парткод: | FE4-1836-000 |
| Деталь: | HANDLE, CST. FRONT COVER |
| Парткод: | FE4-1841-000 |
| Деталь: | PLATE, PAPER SIDE END, REAR |
| Парткод: | FE4-1843-000 |
| Деталь: | HOLDER, DAMPER |
| Парткод: | FE4-1845-000 |
| Деталь: | PLATE, LINK |
| Парткод: | FE4-5920-000 |
| Деталь: | PLATE, LIFTING |
| Парткод: | FL0-0899-000 |
| Деталь: | SHEET, SEPARATION |
| Парткод: | FL0-4008-000 |
| Деталь: | CASSETTE RAIL ASSEMBLY, LEFT |
| Парткод: | FM1-B238-000 |
| Деталь: | SIDE END PLATE ASSEMBLY, FRONT |
| Парткод: | FM1-B240-000 |
| Деталь: | BACK END LIMIT ASSEMBLY |
| Парткод: | FM1-D257-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1081-000 |
| Деталь: | LABEL, CASSETTE |
| Парткод: | FU2-1223-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1278-000 |
| Деталь: | GEAR, 14T |
| Парткод: | RC1-9396-000 |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-1523-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0337-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0359-000 |
| Деталь: | CASSETTE ASSEMBLY |
| Парткод: | FM1-B237-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK4-0641-000 |
| Деталь: | REVERSE DUPLEXING DRIVE ASSY |
| Парткод: | FM1-B230-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1833-000 |
| Деталь: | REVERSE DUPLEXING DRIVE ASSY |
| Парткод: | NPN |
| Деталь: | ROLLER, DRIVEN ROLLER |
| Парткод: | FC0-7610-000 |
| Деталь: | HANDLE, DOOR |
| Парткод: | FE3-1536-000 |
| Деталь: | STOPPER, DOOR |
| Парткод: | FE3-3604-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FE3-6495-000 |
| Деталь: | HOOK |
| Парткод: | FE3-8940-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-9579-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1030-000 |
| Деталь: | RIGHT DOOR ASSEMBLY, LOWER |
| Парткод: | FM1-B244-000 |
| Деталь: | COVER,MULTI PAPER PICK-UP TRAY |
| Парткод: | FE3-1542-000 |
| Деталь: | FLAG, LENGTH SENSOR |
| Парткод: | FE3-1638-000 |
| Деталь: | TRAY, MULTI PAPER PICK-UP SUB |
| Парткод: | FE3-3606-000 |
| Деталь: | HOOK, MULTI FEED TRAY |
| Парткод: | FE3-5650-000 |
| Деталь: | LABEL, MULTI FULL |
| Парткод: | FE3-9856-000 |
| Деталь: | PAPER WIDTH SENSING PCB ASSY |
| Парткод: | FM1-C998-000 |
| Деталь: | CABLE, MULTI PAPER PICK-UP |
| Парткод: | FM1-D829-000 |
| Деталь: | GEAR, 48T |
| Парткод: | FU2-0216-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1067-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1071-000 |
| Деталь: | GEAR, 40T/47T |
| Парткод: | FU2-1075-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | LABEL, FEED MULTIPLE |
| Парткод: | FE3-9836-000 |
| Деталь: | MULTI PAPER PICK-UP TRAY ASSY |
| Парткод: | FM1-B211-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | LINK, MULTI PAPER PICK-UP TRAY |
| Парткод: | FE3-0438-000 |
| Деталь: | LATCH |
| Парткод: | FE3-1414-000 |
| Деталь: | ROLLER, 2ND TRNSFR. OUTER |
| Парткод: | FE3-4783-000 |
| Деталь: | LATCH, FRONT |
| Парткод: | FE3-5602-000 |
| Деталь: | LATCH, REAR |
| Парткод: | FE3-5603-000 |
| Деталь: | COVER, HANDLE |
| Парткод: | FE3-5643-000 |
| Деталь: | RAIL, STOPPER, FRONT |
| Парткод: | FE3-9572-000 |
| Деталь: | RAIL, STOPPER, REAR |
| Парткод: | FE3-9573-000 |
| Деталь: | PLATE, HANDLE GROUNDING |
| Парткод: | FE3-9574-000 |
| Деталь: | HOLDER, DUPLEXING GEAR |
| Парткод: | FE3-9804-000 |
| Деталь: | CLAMP, GEAR HOLDER |
| Парткод: | FE3-9805-000 |
| Деталь: | STOPPER, DUPLEXING, FRONT |
| Парткод: | FE4-1749-000 |
| Деталь: | STOPPER, DUPLEXING, REAR |
| Парткод: | FE4-1750-000 |
| Деталь: | RACK, DAMPER |
| Парткод: | FE4-1755-000 |
| Деталь: | SLIDER |
| Парткод: | FE4-1970-000 |
| Деталь: | ROLLER, REEL |
| Парткод: | FE4-2084-000 |
| Деталь: | ROLLER, DUPLEXING |
| Парткод: | FL0-3979-000 |
| Деталь: | SHEET |
| Парткод: | FL0-4784-000 |
| Деталь: | DUPLEXING REVERSE GEAR ASSY |
| Парткод: | FM1-B207-000 |
| Деталь: | ROLLER, DRIVEN ROLLER |
| Парткод: | FC0-7610-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FE3-1417-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE3-6162-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-9579-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0218-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1030-000 |
| Деталь: | PULLEY, 21T |
| Парткод: | FU2-0184-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0185-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0852-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1074-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1613-140 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | RIGHT DOOR ASSEMBLY |
| Парткод: | FM1-B205-000 |
| Деталь: | CABLE, 2ND TRNSFR. H.V. PCB |
| Парткод: | FM1-D847-000 |
| Деталь: | 2ND TRANSFER H.V. PCB ASSEMBLY |
| Парткод: | FM1-D805-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1172-000 |
| Деталь: | BUSHING |
| Парткод: | FU5-1626-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2654-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2655-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU9-0938-000 |
| Деталь: | ROLLER, REGISTRATION, 1 |
| Парткод: | FC5-4323-000 |
| Деталь: | ROLLER, REGISTRATION, 2 |
| Парткод: | FC5-4324-000 |
| Деталь: | COVER, LED |
| Парткод: | FC9-4964-000 |
| Деталь: | LEVER, EMPTY SENSOR |
| Парткод: | FC9-4971-010 |
| Деталь: | SHUTTER, NOISE-PROOF |
| Парткод: | FE3-5427-000 |
| Деталь: | COUPLING |
| Парткод: | FE3-5438-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-5439-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE3-5441-000 |
| Деталь: | STOPPER |
| Парткод: | FE3-5443-000 |
| Деталь: | KNOB, PAPER PICK-UP COVER |
| Парткод: | FE3-5493-000 |
| Деталь: | COVER, PAPER PICK-UP |
| Парткод: | FL0-1443-000 |
| Деталь: | GUIDE, PAPER PICK-UP |
| Парткод: | FL0-1444-000 |
| Деталь: | ADF PAPER PICK-UP ASSEMBLY |
| Парткод: | FM1-D470-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC9-4968-000 |
| Деталь: | GEAR, 22T/22T |
| Парткод: | FE3-5434-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5436-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5437-000 |
| Деталь: | LEVER |
| Парткод: | FE3-5442-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FE3-5445-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-5468-000 |
| Деталь: | GEAR, 33T |
| Парткод: | FE3-5509-000 |
| Деталь: | LABEL, BLUE |
| Парткод: | FE3-5525-000 |
| Деталь: | SHUTTER |
| Парткод: | FL0-2750-000 |
| Деталь: | GEAR, 20T |
| Парткод: | FU8-0299-000 |
| Деталь: | GEAR, 33T |
| Парткод: | FU8-0890-000 |
| Деталь: | LEVER, STOP |
| Парткод: | FC6-8971-010 |
| Деталь: | JOINT |
| Парткод: | FC8-6353-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FL0-1431-000 |
| Деталь: | LEVER, WIDTH SENSOR |
| Парткод: | FC9-4973-000 |
| Деталь: | LED PCB ASSEMBLY |
| Парткод: | FM1-F923-000 |
| Деталь: | SENSOR PCB ASSY |
| Парткод: | FM4-1747-000 |
| Деталь: | DAMPER, REV. GUIDE RETAINING |
| Парткод: | FC8-6403-010 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0333-000 |
| Деталь: | PAPER PICK-UP COVER ASSY |
| Парткод: | FM1-C226-000 |
| Деталь: | IC, ASIC, T6VN7EFG-0002 |
| Парткод: | FK3-2323-000 |
| Деталь: | IC,TC200GO2EFG-1031,GATE ARRAY |
| Парткод: | FK2-1773-000 |
| Деталь: | DC CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-D804-000 |
| Деталь: | CAP |
| Парткод: | FC0-0695-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FC0-2633-000 |
| Деталь: | STOPPER |
| Парткод: | FE4-2085-000 |
| Деталь: | HOOK, COVER, FRONT |
| Парткод: | FC8-8205-000 |
| Деталь: | GLASS CLEANING ROD ASSEMBLY |
| Парткод: | FM3-5968-010 |
| Деталь: | GUIDE, TRAY |
| Парткод: | FE3-0424-000 |
| Деталь: | COVER, POWER SUPPLY CORD |
| Парткод: | FE3-0815-000 |
| Деталь: | COVER, HANDLE |
| Парткод: | FE3-0851-000 |
| Деталь: | COVER,MAIN POWER SUPPLY SWITCH |
| Парткод: | FE3-0902-000 |
| Деталь: | COVER, RIGHT, FRONT LOWER |
| Парткод: | FE3-0903-000 |
| Деталь: | COVER, RIGHT, FRONT UPPER |
| Парткод: | FE3-0904-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FE3-0907-000 |
| Деталь: | COVER, RIGHT, REAR UPPER |
| Парткод: | FE3-0908-000 |
| Деталь: | COVER, INNER CONNECTOR |
| Парткод: | FE3-0909-000 |
| Деталь: | COVER, RIGHT, LOWER |
| Парткод: | FE3-0911-000 |
| Деталь: | COVER, LEFT, UPPER |
| Парткод: | FE3-0913-000 |
| Деталь: | COVER, LEFT, LOWER |
| Парткод: | FE3-0914-000 |
| Деталь: | RIGHT FRONT UP. COVER ASSEMBLY |
| Парткод: | FE3-0915-000 |
| Деталь: | COVER, INNER, DELV. REAR |
| Парткод: | FE3-0917-000 |
| Деталь: | COVER, HARD DISK DRIVE |
| Парткод: | FE3-0918-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FE3-0919-000 |
| Деталь: | COVER, LEFT, UPPER |
| Парткод: | FE3-0920-000 |
| Деталь: | COVER, INNER, RIGHT |
| Парткод: | FE3-0921-000 |
| Деталь: | COVER, WASTE TONER ASSEMBLY |
| Парткод: | FE3-1060-000 |
| Деталь: | PLATE, FIXED |
| Парткод: | FE3-2472-000 |
| Деталь: | COVER, SUPPORT, LOWER |
| Парткод: | FE3-1338-000 |
| Деталь: | COVER, SUPPORT, SMALL |
| Парткод: | FE3-1339-000 |
| Деталь: | COVER, SUPPORT HINGE, INNER |
| Парткод: | FE3-1340-000 |
| Деталь: | TRAY, FIRST PAPER DELIVERY |
| Парткод: | FE3-1395-000 |
| Деталь: | SHAFT, HINGE |
| Парткод: | FE3-2485-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FE3-1464-000 |
| Деталь: | COVER, SUPPORT HINGE, RIGHT |
| Парткод: | FE3-2481-000 |
| Деталь: | COVER, SUPPORT, REAR |
| Парткод: | FE3-2482-000 |
| Деталь: | GUIDE, REVERSE BACK END |
| Парткод: | FE3-9167-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FE3-9168-000 |
| Деталь: | CAP |
| Парткод: | FE3-9169-000 |
| Деталь: | COVER, THIRD PAPER DELIVERY |
| Парткод: | FE3-9450-000 |
| Деталь: | LABEL, FRONT COVER |
| Парткод: | FE3-9829-000 |
| Деталь: | SUPPORT, PAPER DELIVERY TRAY |
| Парткод: | FE4-7425-000 |
| Деталь: | STOPPER, PUSHING |
| Парткод: | FE4-5318-000 |
| Деталь: | COVER, FRONT UPPER |
| Парткод: | FL0-4915-000 |
| Деталь: | PAD, GLASS CLEANING |
| Парткод: | FL2-9476-000 |
| Деталь: | EMBLEM |
| Парткод: | FL3-1185-000 |
| Деталь: | RIGHT COVER ASSEMBLY, RR. LW. |
| Парткод: | FM1-B195-000 |
| Деталь: | LEFT COVER ASSEMBLY, REAR |
| Парткод: | FM1-C123-000 |
| Деталь: | LABEL, MULTIPLE |
| Парткод: | FE3-9848-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FC8-8346-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, ENV. HEATER SWITCH |
| Парткод: | FC8-4137-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | ROLLER, SECONDARY TRANSFER,FR. |
| Парткод: | FE3-0978-000 |
| Деталь: | BUSHING, FRONT |
| Парткод: | FE3-0982-000 |
| Деталь: | BUSHING, REAR |
| Парткод: | FE3-0983-000 |
| Деталь: | ROLLER, PRIMARY TRANSFER |
| Парткод: | FE3-0986-000 |
| Деталь: | COLLAR |
| Парткод: | FE3-1013-000 |
| Деталь: | COVER, GEAR |
| Парткод: | FE3-1377-000 |
| Деталь: | SIDE PLATE, FRONT |
| Парткод: | FE3-1380-000 |
| Деталь: | RING, GROUNDING |
| Парткод: | FE3-2720-000 |
| Деталь: | COVER, ROLLER |
| Парткод: | FE3-4908-000 |
| Деталь: | COLLAR, DRIVE ROLLER |
| Парткод: | FE3-6304-000 |
| Деталь: | SHEET, LABEL |
| Парткод: | FE3-9830-000 |
| Деталь: | ROLLER, TENSION |
| Парткод: | FL0-0127-000 |
| Деталь: | BELT, INTERMEDIATE TRANSFER |
| Парткод: | FL0-0222-000 |
| Деталь: | TRANSFER CLEANER ASSY |
| Парткод: | FM1-B271-000 |
| Деталь: | GRIP ASSEMBLY |
| Парткод: | FM1-F558-000 |
| Деталь: | GEAR, 15T |
| Парткод: | FU0-0191-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0024-000 |
| Деталь: | GEAR, 2T |
| Парткод: | FU2-0026-000 |
| Деталь: | BUSHING, DRIVE ROLLER, FRONT |
| Парткод: | FU2-0027-000 |
| Деталь: | BUSHING, DRIVE ROLLER, REAR |
| Парткод: | FU2-0028-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU2-0171-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0335-000 |
| Деталь: | BUSHING, FRONT |
| Парткод: | FE3-1001-000 |
| Деталь: | BUSHING, REAR |
| Парткод: | FE3-1002-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-2719-000 |
| Деталь: | ROLLER, DRIVE |
| Парткод: | FL0-0859-000 |
| Деталь: | INTER. TRANSFER BELT ASSY |
| Парткод: | FM1-A605-000 |
| Деталь: | LABEL, QUICK START CAUTION |
| Парткод: | FE3-9859-000 |
| Деталь: | CABLE, SATA POWER |
| Парткод: | FK4-0275-000 |
| Деталь: | CABLE, SATA SIGNAL |
| Парткод: | FK4-0276-000 |
| Деталь: | HARD DISK DRIVE, MQ01ABF032 |
| Парткод: | FK4-1550-000 |
| Деталь: | SWITCH, PUSH |
| Парткод: | WC2-5806-000 |
| Деталь: | DEVELOPING H.V. GUIDE ASSEMBLY |
| Парткод: | FM1-B217-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, C |
| Парткод: | FM1-B218-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, BK |
| Парткод: | FM1-B219-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, Y |
| Парткод: | FM1-B220-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, M |
| Парткод: | FM1-B221-000 |
| Деталь: | INTERLOCK SWITCH ASSEMBLY |
| Парткод: | FM1-B227-000 |
| Деталь: | MULTI REEL ASSEMBLY |
| Парткод: | FM1-C283-000 |
| Деталь: | CABLE, AC DRIVER |
| Парткод: | FM1-D811-000 |
| Деталь: | CABLE, HEATER |
| Парткод: | FM1-D815-000 |
| Деталь: | CABLE, DDIP |
| Парткод: | FM1-D818-000 |
| Деталь: | CABLE, FEED |
| Парткод: | FM1-D824-000 |
| Деталь: | CABLE, PICK-UP |
| Парткод: | FM1-D827-000 |
| Деталь: | CABLE, ECO-ID |
| Парткод: | FM1-D841-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | CONNECTOR, SNAP TIGHT, W |
| Парткод: | VS1-7440-011 |
| Деталь: | CONNECTOR, SNAP TIGHT, W |
| Парткод: | VS1-7504-015 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | DAMPER, CUSHION |
| Парткод: | XH9-0149-000 |
| Деталь: | SPACER |
| Парткод: | XZ1-1301-005 |
| Деталь: | MACHINE REAR PLATE 1 |
| Парткод: | NPN |
| Деталь: | CAP |
| Парткод: | FC0-0695-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FC0-2633-000 |
| Деталь: | STOPPER |
| Парткод: | FE4-2085-000 |
| Деталь: | HOOK, COVER, FRONT |
| Парткод: | FC8-8205-000 |
| Деталь: | GLASS CLEANING ROD ASSEMBLY |
| Парткод: | FM3-5968-010 |
| Деталь: | GUIDE, TRAY |
| Парткод: | FE3-0424-000 |
| Деталь: | COVER, POWER SUPPLY CORD |
| Парткод: | FE3-0815-000 |
| Деталь: | COVER, HANDLE |
| Парткод: | FE3-0851-000 |
| Деталь: | COVER,MAIN POWER SUPPLY SWITCH |
| Парткод: | FE3-0902-000 |
| Деталь: | COVER, RIGHT, FRONT LOWER |
| Парткод: | FE3-0903-000 |
| Деталь: | COVER, RIGHT, FRONT UPPER |
| Парткод: | FE3-0904-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FE3-0907-000 |
| Деталь: | COVER, RIGHT, REAR UPPER |
| Парткод: | FE3-0908-000 |
| Деталь: | COVER, INNER CONNECTOR |
| Парткод: | FE3-0909-000 |
| Деталь: | COVER, RIGHT, LOWER |
| Парткод: | FE3-0911-000 |
| Деталь: | COVER, LEFT, UPPER |
| Парткод: | FE3-0913-000 |
| Деталь: | COVER, LEFT, LOWER |
| Парткод: | FE3-0914-000 |
| Деталь: | RIGHT FRONT UP. COVER ASSEMBLY |
| Парткод: | FE3-0915-000 |
| Деталь: | COVER, INNER, DELV. REAR |
| Парткод: | FE3-0917-000 |
| Деталь: | COVER, HARD DISK DRIVE |
| Парткод: | FE3-0918-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FE3-0919-000 |
| Деталь: | COVER, LEFT, UPPER |
| Парткод: | FE3-0920-000 |
| Деталь: | COVER, INNER, RIGHT |
| Парткод: | FE3-0921-000 |
| Деталь: | COVER, WASTE TONER ASSEMBLY |
| Парткод: | FE3-1060-000 |
| Деталь: | PLATE, FIXED |
| Парткод: | FE3-2472-000 |
| Деталь: | COVER, SUPPORT, LOWER |
| Парткод: | FE3-1338-000 |
| Деталь: | COVER, SUPPORT, SMALL |
| Парткод: | FE3-1339-000 |
| Деталь: | COVER, SUPPORT HINGE, INNER |
| Парткод: | FE3-1340-000 |
| Деталь: | TRAY, FIRST PAPER DELIVERY |
| Парткод: | FE3-1395-000 |
| Деталь: | SHAFT, HINGE |
| Парткод: | FE3-2485-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FE3-1464-000 |
| Деталь: | COVER, SUPPORT HINGE, RIGHT |
| Парткод: | FE3-2481-000 |
| Деталь: | COVER, SUPPORT, REAR |
| Парткод: | FE3-2482-000 |
| Деталь: | GUIDE, REVERSE BACK END |
| Парткод: | FE3-9167-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FE3-9168-000 |
| Деталь: | CAP |
| Парткод: | FE3-9169-000 |
| Деталь: | COVER, THIRD PAPER DELIVERY |
| Парткод: | FE3-9450-000 |
| Деталь: | LABEL, FRONT COVER |
| Парткод: | FE3-9829-000 |
| Деталь: | SUPPORT, PAPER DELIVERY TRAY |
| Парткод: | FE4-7425-000 |
| Деталь: | STOPPER, PUSHING |
| Парткод: | FE4-5318-000 |
| Деталь: | COVER, FRONT UPPER |
| Парткод: | FL0-4915-000 |
| Деталь: | PAD, GLASS CLEANING |
| Парткод: | FL2-9476-000 |
| Деталь: | EMBLEM |
| Парткод: | FL3-1185-000 |
| Деталь: | RIGHT COVER ASSEMBLY, RR. LW. |
| Парткод: | FM1-B195-000 |
| Деталь: | LEFT COVER ASSEMBLY, REAR |
| Парткод: | FM1-C123-000 |
| Деталь: | LABEL, MULTIPLE |
| Парткод: | FE3-9848-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FC8-8346-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, ENV. HEATER SWITCH |
| Парткод: | FC8-4137-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | SHAFT, CAM |
| Парткод: | FE3-1203-000 |
| Деталь: | CAM, PRESSURE RELEASE |
| Парткод: | FE3-1220-000 |
| Деталь: | COVER, FIXING MAIN |
| Парткод: | FL0-0903-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM1-D280-000 |
| Деталь: | FIXING COVER ASSEMBLY, FRONT |
| Парткод: | FM1-B671-000 |
| Деталь: | CABLE, FIXING OUTLET |
| Парткод: | FM1-D823-000 |
| Деталь: | FIXING COVER KIT, REAR |
| Парткод: | FM1-K197-000 |
| Деталь: | PRESSURE ROLLER KIT |
| Парткод: | FM1-K441-000 |
| Деталь: | CAM/GEAR, 21T |
| Парткод: | FU2-0133-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-0134-000 |
| Деталь: | GEAR, 36T |
| Парткод: | FU2-1372-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | FIXING ASSEMBLY, FX-202 |
| Парткод: | FM1-D276-000 |
| Деталь: | SUPPORT, POWER SUPPLY |
| Парткод: | FE3-0820-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | POWER SUPPLY ASSEMBLY |
| Парткод: | FM1-C281-000 |
| Деталь: | SCREW, FIXED, M4 |
| Парткод: | FU5-9167-000 |
| Деталь: | SCREW, STEPPED, M5 |
| Парткод: | FU5-9168-000 |
| Деталь: | MOUNTING HARDWARE(ADF) |
| Парткод: | NPN |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FE4-8959-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE3-1124-000 |
| Деталь: | LEVER |
| Парткод: | FE3-1136-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FE3-1392-000 |
| Деталь: | FLAG, PAPER DELIVERY SENSOR |
| Парткод: | FE3-5646-000 |
| Деталь: | FLAG, FULL DETECT |
| Парткод: | FE3-9441-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-9443-000 |
| Деталь: | HOLDER, ROLLER SHAFT |
| Парткод: | FE3-9444-000 |
| Деталь: | RING, O |
| Парткод: | FE4-0668-000 |
| Деталь: | ROLLER |
| Парткод: | FE4-0669-000 |
| Деталь: | HOLDER, ROLLER RING |
| Парткод: | FE4-0671-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK4-0641-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FL0-0139-000 |
| Деталь: | FLAPPER,2ND/3RD PAPER DELIVERY |
| Парткод: | FL0-0813-000 |
| Деталь: | 2ND/3RD DELIVERY DRIVE ASSY |
| Парткод: | FM1-B274-000 |
| Деталь: | CABLE, MOTOR |
| Парткод: | FM1-D877-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU2-0094-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0179-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0180-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0181-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0710-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0711-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0712-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1833-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-1505-000 |
| Деталь: | SHAFT, ROLLER |
| Парткод: | FE3-1401-000 |
| Деталь: | SECOND PAPER DELIVERY ASSEMBLY |
| Парткод: | FM1-B273-000 |
| Деталь: | CABLE, SWITCH |
| Парткод: | FM1-D859-000 |
| Деталь: | SWITCH, PUSH |
| Парткод: | WC2-5806-000 |
| Деталь: | VERTICAL PATH DRIVE ASSEMBLY |
| Парткод: | FM1-B203-000 |
| Деталь: | IC,TC200GO2EFG-1031,GATE ARRAY |
| Парткод: | FK2-1773-000 |
| Деталь: | ADF CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-F920-000 |
| Деталь: | LEVER, REGISTRATION LOCK,FRONT |
| Парткод: | FE3-1369-000 |
| Деталь: | LEVER, REGISTRATION LOCK, REAR |
| Парткод: | FE3-1370-000 |
| Деталь: | GUIDE, REGISTRATION CABLE |
| Парткод: | FE3-6307-000 |
| Деталь: | SENSOR UNIT, REG. PATCH, PHOTO |
| Парткод: | FM1-A626-000 |
| Деталь: | I.T.B. RAIL ASSEMBLY, FRONT |
| Парткод: | FM1-B258-000 |
| Деталь: | I.T.B. RAIL ASSEMBLY, REAR |
| Парткод: | FM1-B259-000 |
| Деталь: | DAMPER ASSEMBLY |
| Парткод: | FM1-G725-000 |
| Деталь: | LEVER ASSEMBLY, REAR |
| Парткод: | FM1-K302-000 |
| Деталь: | LEVER ASSEMBLY, FRONT |
| Парткод: | FM1-K303-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1833-000 |
| Деталь: | FOOT, RUBBER |
| Парткод: | XH9-0136-000 |
| Деталь: | INTERNAL COMPONENTS 5 |
| Парткод: | NPN |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK4-0640-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK4-0641-000 |
| Деталь: | H.V. CONTACT GUIDE ASSEMBLY |
| Парткод: | FM1-B216-000 |
| Деталь: | SECONDARY H.V. GUIDE ASSEMBLY |
| Парткод: | FM1-B222-000 |
| Деталь: | CABLE, HEATER |
| Парткод: | FM1-B495-000 |
| Деталь: | FLEXIBLE FLAT CABLE ASSEMBLY |
| Парткод: | FM1-B497-000 |
| Деталь: | CASSETTE AUTO CLOSE ASSEMBLY |
| Парткод: | FM1-B670-000 |
| Деталь: | WASTE TONER FULL DETECT ASSY |
| Парткод: | FM1-D185-000 |
| Деталь: | PRE-EXPOSURE DRIVER PCB ASSY |
| Парткод: | FM1-D808-000 |
| Деталь: | CABLE, FEED MOTOR |
| Парткод: | FM1-D834-000 |
| Деталь: | CABLE, WASTE TONER SENSOR |
| Парткод: | FM1-D838-000 |
| Деталь: | CABLE, BOTTLE CONNECTOR |
| Парткод: | FM1-D853-000 |
| Деталь: | CABLE, EXTRACTION MOTOR |
| Парткод: | FM1-D857-000 |
| Деталь: | CABLE, LED DRIVER CONNECTING |
| Парткод: | FM1-D864-000 |
| Деталь: | CABLE, LED DRIVER RELAY |
| Парткод: | FM1-D865-000 |
| Деталь: | PRE-EXPOSURE CABLE GUIDE UNIT |
| Парткод: | FM1-K255-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-005 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7177-013 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-009 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-013 |
| Деталь: | CONNECTOR, SNAP TIGHT, 8P, W |
| Парткод: | VS1-8959-008 |
| Деталь: | SWITCH, PUSH |
| Парткод: | WC2-5806-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1833-000 |
| Деталь: | MACHINE REAR PLATE 2 |
| Парткод: | NPN |
| Деталь: | ROLLER, PAPER FEED, 1 |
| Парткод: | FC5-4286-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2652-000 |
| Деталь: | CLIP |
| Парткод: | FC5-4425-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FC6-8973-000 |
| Деталь: | HOLDER, SOLENOID |
| Парткод: | FC8-6319-000 |
| Деталь: | ROLLER, READ 2 PINCH |
| Парткод: | FC8-6404-000 |
| Деталь: | SHAFT, PAPER FEED ROLLER |
| Парткод: | FE2-1601-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FE3-5400-000 |
| Деталь: | HOLDER, ROLLER, SMALL |
| Парткод: | FL0-2751-000 |
| Деталь: | HOLDER, ROLLER, LARGE |
| Парткод: | FL0-2752-000 |
| Деталь: | COVER, BASE, LOWER |
| Парткод: | FL0-2753-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FL0-2755-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6316-000 |
| Деталь: | CAM, DELIVERY ESTRANGEMENT |
| Парткод: | FC8-6318-010 |
| Деталь: | DAMPER, DELIVERY |
| Парткод: | FE3-5454-000 |
| Деталь: | HOLDER, DELIVERY ROLLER |
| Парткод: | FC8-6317-000 |
| Деталь: | CABLE, SOLENOID |
| Парткод: | FM1-G897-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | BUSHING |
| Парткод: | FU5-1168-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0334-000 |
| Деталь: | BASE ASSEMBLY |
| Парткод: | NPN |
| Деталь: | SHEET, CABLE RETAINING |
| Парткод: | FC0-0463-000 |
| Деталь: | COVER, HINGE LOWER, LEFT |
| Парткод: | FC0-0472-000 |
| Деталь: | COVER, HINGE LOWER, RIGHT |
| Парткод: | FC0-0473-000 |
| Деталь: | FLAG, OPEN/CLOSE SENSOR |
| Парткод: | FC0-0679-000 |
| Деталь: | SHEET, HINGE COVER |
| Парткод: | FC0-0691-000 |
| Деталь: | COVER, GLASS SUPPORT |
| Парткод: | FC0-2618-000 |
| Деталь: | PULLEY |
| Парткод: | FC8-6163-000 |
| Деталь: | PULLEY |
| Парткод: | FC8-6180-000 |
| Деталь: | COVER, GLASS RETAINING |
| Парткод: | FC9-7288-010 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FC9-7297-000 |
| Деталь: | SEAL, CABLE BLANKING |
| Парткод: | FC9-7300-000 |
| Деталь: | COVER, PCB |
| Парткод: | FE2-1747-020 |
| Деталь: | SPACER, SHAFT CUSHION |
| Парткод: | FE2-1752-000 |
| Деталь: | COVER, READER, FRONT |
| Парткод: | FE3-3609-000 |
| Деталь: | COVER, READER FRONT, SMALL |
| Парткод: | FE3-3611-000 |
| Деталь: | MOUNT, OPEN/CLOSE SENSOR FLAG |
| Парткод: | FE3-3614-000 |
| Деталь: | COVER, READER, RIGHT |
| Парткод: | FE3-3623-000 |
| Деталь: | IC, PHOTO SENSOR,DOCUMENT SIZE |
| Парткод: | FK3-0871-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-3873-000 |
| Деталь: | SHEET, HEATER |
| Парткод: | FL0-0833-000 |
| Деталь: | COVER, READER, REAR |
| Парткод: | FL0-2485-000 |
| Деталь: | GLASS, READER |
| Парткод: | FL3-3206-000 |
| Деталь: | FRAME, JUMP GUIDE |
| Парткод: | FL3-4610-000 |
| Деталь: | COVER, GLASS RETAINING |
| Парткод: | FL3-4761-000 |
| Деталь: | GLASS, COPYBOARD |
| Парткод: | FL3-4767-000 |
| Деталь: | COVER, READER, LEFT |
| Парткод: | FL3-6227-000 |
| Деталь: | CABLE, SENSOR |
| Парткод: | FM0-4613-000 |
| Деталь: | CABLE, MOTOR |
| Парткод: | FM0-4614-000 |
| Деталь: | CABLE, ADF DATA CONNECTING |
| Парткод: | FM0-4617-000 |
| Деталь: | CABLE, ADF POWER CONNECTING |
| Парткод: | FM0-4618-000 |
| Деталь: | CABLE, SIZE DETECT |
| Парткод: | FM0-4619-000 |
| Деталь: | SCANNER UNIT |
| Парткод: | FM1-D535-000 |
| Деталь: | CABLE, HEATER RELAY |
| Парткод: | FM1-E825-000 |
| Деталь: | MOTOR ASSY |
| Парткод: | FM4-6171-000 |
| Деталь: | PULLEY |
| Парткод: | FU5-3710-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2481-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU8-2497-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU8-2600-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-006 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-019 |
| Деталь: | IC, PHOTO-INTERRUPTER |
| Парткод: | WG8-5848-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW,M3X5 |
| Парткод: | XA9-1116-030 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | SCREW, FLAT HEAD, M4 |
| Парткод: | XA9-1415-000 |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-4606-835 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-4668-040 |
| Деталь: | CAP |
| Парткод: | FC0-0695-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE4-0136-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE4-0138-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE4-0141-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE4-0143-000 |
| Деталь: | LABEL, CLEANING POSITION |
| Парткод: | FE3-9798-000 |
| Деталь: | SEAL ASSEMBLY |
| Парткод: | FL0-3215-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FL0-2928-000 |
| Деталь: | SEAL, BLANKING |
| Парткод: | FL0-2930-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | NPN |
| Деталь: | CAP |
| Парткод: | FC0-0695-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FC0-2633-000 |
| Деталь: | STOPPER |
| Парткод: | FE4-2085-000 |
| Деталь: | HOOK, COVER, FRONT |
| Парткод: | FC8-8205-000 |
| Деталь: | GLASS CLEANING ROD ASSEMBLY |
| Парткод: | FM3-5968-010 |
| Деталь: | GUIDE, TRAY |
| Парткод: | FE3-0424-000 |
| Деталь: | COVER, POWER SUPPLY CORD |
| Парткод: | FE3-0815-000 |
| Деталь: | COVER, HANDLE |
| Парткод: | FE3-0851-000 |
| Деталь: | COVER,MAIN POWER SUPPLY SWITCH |
| Парткод: | FE3-0902-000 |
| Деталь: | COVER, RIGHT, FRONT LOWER |
| Парткод: | FE3-0903-000 |
| Деталь: | COVER, RIGHT, FRONT UPPER |
| Парткод: | FE3-0904-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FE3-0907-000 |
| Деталь: | COVER, RIGHT, REAR UPPER |
| Парткод: | FE3-0908-000 |
| Деталь: | COVER, INNER CONNECTOR |
| Парткод: | FE3-0909-000 |
| Деталь: | COVER, RIGHT, LOWER |
| Парткод: | FE3-0911-000 |
| Деталь: | COVER, LEFT, UPPER |
| Парткод: | FE3-0913-000 |
| Деталь: | COVER, LEFT, LOWER |
| Парткод: | FE3-0914-000 |
| Деталь: | RIGHT FRONT UP. COVER ASSEMBLY |
| Парткод: | FE3-0915-000 |
| Деталь: | COVER, INNER, DELV. REAR |
| Парткод: | FE3-0917-000 |
| Деталь: | COVER, HARD DISK DRIVE |
| Парткод: | FE3-0918-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FE3-0919-000 |
| Деталь: | COVER, LEFT, UPPER |
| Парткод: | FE3-0920-000 |
| Деталь: | COVER, INNER, RIGHT |
| Парткод: | FE3-0921-000 |
| Деталь: | COVER, WASTE TONER ASSEMBLY |
| Парткод: | FE3-1060-000 |
| Деталь: | PLATE, FIXED |
| Парткод: | FE3-2472-000 |
| Деталь: | COVER, SUPPORT, LOWER |
| Парткод: | FE3-1338-000 |
| Деталь: | COVER, SUPPORT, SMALL |
| Парткод: | FE3-1339-000 |
| Деталь: | COVER, SUPPORT HINGE, INNER |
| Парткод: | FE3-1340-000 |
| Деталь: | TRAY, FIRST PAPER DELIVERY |
| Парткод: | FE3-1395-000 |
| Деталь: | SHAFT, HINGE |
| Парткод: | FE3-2485-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FE3-1464-000 |
| Деталь: | COVER, SUPPORT HINGE, RIGHT |
| Парткод: | FE3-2481-000 |
| Деталь: | COVER, SUPPORT, REAR |
| Парткод: | FE3-2482-000 |
| Деталь: | GUIDE, REVERSE BACK END |
| Парткод: | FE3-9167-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FE3-9168-000 |
| Деталь: | CAP |
| Парткод: | FE3-9169-000 |
| Деталь: | COVER, THIRD PAPER DELIVERY |
| Парткод: | FE3-9450-000 |
| Деталь: | LABEL, FRONT COVER |
| Парткод: | FE3-9829-000 |
| Деталь: | SUPPORT, PAPER DELIVERY TRAY |
| Парткод: | FE4-7425-000 |
| Деталь: | STOPPER, PUSHING |
| Парткод: | FE4-5318-000 |
| Деталь: | COVER, FRONT UPPER |
| Парткод: | FL0-4915-000 |
| Деталь: | PAD, GLASS CLEANING |
| Парткод: | FL2-9476-000 |
| Деталь: | EMBLEM |
| Парткод: | FL3-1185-000 |
| Деталь: | RIGHT COVER ASSEMBLY, RR. LW. |
| Парткод: | FM1-B195-000 |
| Деталь: | LEFT COVER ASSEMBLY, REAR |
| Парткод: | FM1-C123-000 |
| Деталь: | LABEL, MULTIPLE |
| Парткод: | FE3-9848-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FC8-8346-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, ENV. HEATER SWITCH |
| Парткод: | FC8-4137-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | CASE, PRIMARY TRANSFER H.V. |
| Парткод: | FE3-0769-000 |
| Деталь: | 1ST TRANSFER H.V. PCB ASSY |
| Парткод: | FM1-C996-000 |
| Деталь: | CABLE, PRIMARY TRANSFER H.V. |
| Парткод: | FM1-D839-000 |
| Деталь: | PRIMARY TRANSFER H.V. ASSEMBLY |
| Парткод: | NPN |
| Деталь: | LED PCB ASSEMBLY |
| Парткод: | FM1-F921-000 |
| Деталь: | SENSOR PCB ASSY |
| Парткод: | FM1-F922-000 |
| Деталь: | PINION, 22T |
| Парткод: | FU8-0910-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | IC,PHOTO SENSOR PS126EL1 |
| Парткод: | WP2-5428-000 |
| Деталь: | LEVER, TRAY SENSOR |
| Парткод: | FC8-6339-000 |
| Деталь: | HOLDER, PCB |
| Парткод: | FE3-5420-000 |
| Деталь: | RACK, TRAY |
| Парткод: | FE3-5421-000 |
| Деталь: | HOLDER, STOPPER |
| Парткод: | FE3-5422-000 |
| Деталь: | STOPPER, DOCUMENT |
| Парткод: | FE3-5423-000 |
| Деталь: | HOLDER, PCB |
| Парткод: | FE3-5444-000 |
| Деталь: | SHEET, GROUNDING |
| Парткод: | FE4-1405-000 |
| Деталь: | COVER, TRAY, LOWER |
| Парткод: | FL0-1435-000 |
| Деталь: | TRAY, DOCUMENT |
| Парткод: | FL0-1436-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FL0-3192-000 |
| Деталь: | GUIDE, TRAY, FRONT |
| Парткод: | FL0-2748-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FU7-8133-000 |
| Деталь: | GUIDE, TRAY, REAR |
| Парткод: | FL0-2749-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FU7-8134-000 |
| Деталь: | DOCUMENT TRAY ASSY |
| Парткод: | FM1-C227-000 |
| Деталь: | COVER, ENGINE, LOWER |
| Парткод: | FE3-0848-000 |
| Деталь: | GUIDE, BLACK |
| Парткод: | FE3-0962-000 |
| Деталь: | GUIDE, COLLAR |
| Парткод: | FE3-0963-000 |
| Деталь: | LINK, FRONT |
| Парткод: | FE3-0969-000 |
| Деталь: | ROLLER, RAIL |
| Парткод: | FE3-1352-000 |
| Деталь: | COVER, WASTE TONER CASE |
| Парткод: | FE4-0200-000 |
| Деталь: | COVER, DOOR LOCK |
| Парткод: | FE4-1407-000 |
| Деталь: | SPRING, RETAINING |
| Парткод: | FE4-1978-000 |
| Деталь: | NEW OLD SENSING HOLDER ASSY |
| Парткод: | FM1-B197-000 |
| Деталь: | CASSETTE SIZE SENSING ASSY |
| Парткод: | FM1-B198-000 |
| Деталь: | CABLE, TONER BOTTLE |
| Парткод: | FM1-D830-000 |
| Деталь: | CABLE, CASSETTE SIZE |
| Парткод: | FM1-D837-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-006 |
| Деталь: | CONNECTOR, SNAP TIGHT, 3P |
| Парткод: | VS1-7504-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, 16P |
| Парткод: | VS1-7504-016 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | KEY TOP, SETTINGS/REGISTRATION |
| Парткод: | FC8-8649-000 |
| Деталь: | KEY TOP, COUNTER CHECK |
| Парткод: | FC8-8655-000 |
| Деталь: | KEY TOP, NUMBERS |
| Парткод: | FC9-5290-000 |
| Деталь: | KEY, STOP |
| Парткод: | FE3-1334-000 |
| Деталь: | PILLAR, HINGE |
| Парткод: | FE3-1336-000 |
| Деталь: | KEY, VOLUME |
| Парткод: | FE3-1337-000 |
| Деталь: | COVER, TOUCH PANEL |
| Парткод: | FE3-1345-000 |
| Деталь: | COVER, LCD |
| Парткод: | FE3-2473-000 |
| Деталь: | SHEET, ELES. PREVENTION |
| Парткод: | FE3-2474-000 |
| Деталь: | BASE, COVER, UPPER |
| Парткод: | FE3-2475-000 |
| Деталь: | COVER, LOWER |
| Парткод: | FE3-2476-000 |
| Деталь: | PEN, PANEL TOUCH |
| Парткод: | FE3-2478-000 |
| Деталь: | KEY TOP, ENERGY SAVE |
| Парткод: | FE3-2487-000 |
| Деталь: | COVER, LAMP |
| Парткод: | FE3-2489-000 |
| Деталь: | KEY TOP, BRIGHTNESS ADJUSTMENT |
| Парткод: | FE3-7557-000 |
| Деталь: | KEY TOP, RESET |
| Парткод: | FE3-9931-000 |
| Деталь: | PANEL, TOUCH |
| Парткод: | FK4-0092-000 |
| Деталь: | KEY TOP, START |
| Парткод: | FL0-1151-000 |
| Деталь: | STAY, CONTROL PANEL ASSEMBLY |
| Парткод: | FL0-2942-000 |
| Деталь: | LCD |
| Парткод: | FL0-5115-000 |
| Деталь: | HINGE, CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-B223-000 |
| Деталь: | CABLE, NUMBERS KEY |
| Парткод: | FM1-B841-000 |
| Деталь: | CPU PCB ASSEMBLY |
| Парткод: | FM1-B842-000 |
| Деталь: | NUMBERS KEY PCB ASSEMBLY |
| Парткод: | FM1-B843-000 |
| Деталь: | CAP |
| Парткод: | FE3-9169-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FE4-1875-000 |
| Деталь: | COVER, UPPER |
| Парткод: | FE3-2480-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A612-000 |
| Деталь: | WASTE TONER FEED DRIVE ASSY |
| Парткод: | FM1-B245-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FE3-1057-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-1444-000 |
| Деталь: | COVER, DRUM UNIT RETAINING |
| Парткод: | FE3-1446-000 |
| Деталь: | BLOCK, TRAY, BLACK |
| Парткод: | FE3-6420-000 |
| Деталь: | BLOCK, TRAY, CYAN |
| Парткод: | FE3-6421-000 |
| Деталь: | BLOCK, TRAY, MAGENTA |
| Парткод: | FE3-6422-000 |
| Деталь: | BLOCK, TRAY, YELLOW |
| Парткод: | FE3-6423-000 |
| Деталь: | GUIDE, LASER WIPER |
| Парткод: | FE3-9148-000 |
| Деталь: | LABEL, MULTIPLE |
| Парткод: | FE3-9848-000 |
| Деталь: | TRAY, DEVELOPING |
| Парткод: | FL0-1718-000 |
| Деталь: | DEVELOPING CROSSMEMBER ASSY |
| Парткод: | FM1-B186-000 |
| Деталь: | DRUM RAIL ASSEMBLY |
| Парткод: | FM1-B187-000 |
| Деталь: | WASTE TONER GEAR ASSEMBLY |
| Парткод: | FM1-D184-000 |
| Деталь: | INTERMEDIATE GUIDE ASSEMBLY |
| Парткод: | FM1-D186-000 |
| Деталь: | WASTE TONER GEAR HOLDER ASSY |
| Парткод: | FM1-D187-000 |
| Деталь: | CABLE, FRONT |
| Парткод: | FM1-D832-000 |
| Деталь: | CABLE, RELAY |
| Парткод: | FM1-D852-000 |
| Деталь: | GEAR, 31T/15T |
| Парткод: | FU2-0046-000 |
| Деталь: | GEAR, 19T |
| Парткод: | FU2-0052-000 |
| Деталь: | SCREW, STEPPED, M3 |
| Парткод: | FU5-9353-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5888-000 |
| Деталь: | COUPLING |
| Парткод: | FC0-7669-000 |
| Деталь: | LEVER, PAPER DETECT |
| Парткод: | FC0-7670-000 |
| Деталь: | ARM |
| Парткод: | FE3-1558-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FE3-1586-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE3-1595-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-1617-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-1619-000 |
| Деталь: | LEVER, LATCH |
| Парткод: | FE3-1650-000 |
| Деталь: | GEAR, 26T |
| Парткод: | FE3-3590-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FE3-4861-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-5669-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-6168-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-6170-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FE3-7684-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-7685-000 |
| Деталь: | GUIDE, VERTICAL PATH, LOWER |
| Парткод: | FE3-8285-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE4-0215-000 |
| Деталь: | LEVER, ESTRANGEMENT |
| Парткод: | FE4-1504-000 |
| Деталь: | LIMITTER, TORQUE |
| Парткод: | FE4-1528-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE4-1660-000 |
| Деталь: | HOLDER, PAPER PICK-UP ROLLER |
| Парткод: | FE4-8286-000 |
| Деталь: | SHEET, GUIDE |
| Парткод: | FL0-1161-000 |
| Деталь: | ONE-WAY CLUTCH ASSEMBLY |
| Парткод: | FL0-1515-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-1516-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1674-000 |
| Цена: | 5 000 ₽ |
| Деталь: | ROLLER, EXTRACTION |
| Парткод: | FL0-1834-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-2885-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FL0-3191-000 |
| Деталь: | SHAFT, PAPER PICK-UP |
| Парткод: | FL0-3632-000 |
| Деталь: | HOLDER, SEPARATION ROLLER |
| Парткод: | FL0-3633-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-4002-000 |
| Цена: | 4 900 ₽ |
| Деталь: | GUIDE, SLIDE |
| Парткод: | FL0-6486-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-B236-000 |
| Деталь: | CABLE, CASSETTE SENSOR |
| Парткод: | FM1-D828-000 |
| Деталь: | BUSHING |
| Парткод: | FS1-1205-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU2-0248-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1069-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-1414-000 |
| Деталь: | CONNECTOR, 9P |
| Парткод: | VS1-7177-009 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | PAPER PICK-UP ASSEMBLY |
| Парткод: | FM1-B501-000 |
| Деталь: | FIXING DRIVE MOTOR ASSEMBLY |
| Парткод: | FM1-B263-000 |
| Деталь: | FIXING DRIVE ASSEMBLY |
| Парткод: | FM1-B261-000 |
| Деталь: | KEY TOP, SETTINGS/REGISTRATION |
| Парткод: | FC8-8649-000 |
| Деталь: | KEY TOP, COUNTER CHECK |
| Парткод: | FC8-8655-000 |
| Деталь: | KEY TOP, NUMBERS |
| Парткод: | FC9-5290-000 |
| Деталь: | KEY, STOP |
| Парткод: | FE3-1334-000 |
| Деталь: | PILLAR, HINGE |
| Парткод: | FE3-1336-000 |
| Деталь: | KEY, VOLUME |
| Парткод: | FE3-1337-000 |
| Деталь: | COVER, TOUCH PANEL |
| Парткод: | FE3-1345-000 |
| Деталь: | COVER, LCD |
| Парткод: | FE3-2473-000 |
| Деталь: | SHEET, ELES. PREVENTION |
| Парткод: | FE3-2474-000 |
| Деталь: | BASE, COVER, UPPER |
| Парткод: | FE3-2475-000 |
| Деталь: | COVER, LOWER |
| Парткод: | FE3-2476-000 |
| Деталь: | PEN, PANEL TOUCH |
| Парткод: | FE3-2478-000 |
| Деталь: | KEY TOP, ENERGY SAVE |
| Парткод: | FE3-2487-000 |
| Деталь: | COVER, LAMP |
| Парткод: | FE3-2489-000 |
| Деталь: | KEY TOP, BRIGHTNESS ADJUSTMENT |
| Парткод: | FE3-7557-000 |
| Деталь: | KEY TOP, RESET |
| Парткод: | FE3-9931-000 |
| Деталь: | PANEL, TOUCH |
| Парткод: | FK4-0092-000 |
| Деталь: | KEY TOP, START |
| Парткод: | FL0-1151-000 |
| Деталь: | STAY, CONTROL PANEL ASSEMBLY |
| Парткод: | FL0-2942-000 |
| Деталь: | LCD |
| Парткод: | FL0-5115-000 |
| Деталь: | HINGE, CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-B223-000 |
| Деталь: | CABLE, NUMBERS KEY |
| Парткод: | FM1-B841-000 |
| Деталь: | CPU PCB ASSEMBLY |
| Парткод: | FM1-B842-000 |
| Деталь: | NUMBERS KEY PCB ASSEMBLY |
| Парткод: | FM1-B843-000 |
| Деталь: | CAP |
| Парткод: | FE3-9169-000 |
| Деталь: | SHEET, CONTROL PANEL |
| Парткод: | FE3-8366-000 |
| Деталь: | COVER, UPPER |
| Парткод: | FE3-2480-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-A612-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7440-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, 4P, W |
| Парткод: | VS1-8959-004 |
| Деталь: | BOTTLE DRIVE ASSEMBLY, Y, M |
| Парткод: | FM1-B249-000 |
| Деталь: | SHEET, PROTECTION |
| Парткод: | FL0-3260-000 |
| Деталь: | LASER SCANNER ASSEMBLY |
| Парткод: | FM1-D175-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FE4-8959-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FE2-2111-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-9443-000 |
| Деталь: | COVER, REVERSE GUIDE |
| Парткод: | FE3-1109-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FE3-1392-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE3-4941-000 |
| Деталь: | PIN, DRIVEN ROLLER |
| Парткод: | FE4-0647-000 |
| Деталь: | RING, O |
| Парткод: | FE4-0668-000 |
| Деталь: | HOLDER, ROLLER RING |
| Парткод: | FE4-0671-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FE4-1759-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE4-1760-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FE4-3773-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE4-3774-000 |
| Деталь: | ONE-WAY GEAR ASSEMBLY |
| Парткод: | FM1-B241-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-1516-000 |
| Деталь: | FLAPPER |
| Парткод: | FL0-3366-000 |
| Деталь: | ROLLER, DRIVEN |
| Парткод: | FL0-3367-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FL0-3370-000 |
| Деталь: | ROLLER, DRIVE |
| Парткод: | FL0-3982-000 |
| Деталь: | ROLLER, REVERSE DRIVEN |
| Парткод: | FL0-4786-000 |
| Деталь: | PAPER DELIVERY DRIVE ASSEMBLY |
| Парткод: | FM1-B233-000 |
| Деталь: | SOLENOID ASSEMBLY |
| Парткод: | FM1-B234-000 |
| Деталь: | PAPER DELIVERY LEVER ASSY, 1 |
| Парткод: | FM1-D193-000 |
| Деталь: | PAPER DELIVERY LEVER ASSY, 2 |
| Парткод: | FM1-G210-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU2-0094-000 |
| Деталь: | GEAR, 26T |
| Парткод: | FU2-0096-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0179-000 |
| Деталь: | GEAR, 42T |
| Парткод: | FU2-0186-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0550-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0551-000 |
| Деталь: | GEAR, 19T/30T |
| Парткод: | FU2-0567-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0606-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0607-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1058-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1059-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1060-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU2-1073-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1390-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE3-1403-000 |
| Деталь: | WASHER,COP |
| Парткод: | XD1-1106-234 |
| Деталь: | FIRST PAPER DELIVERY ASSEMBLY |
| Парткод: | FM1-D275-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-G727-000 |
| Деталь: | TPM PCB ASSEMBLY |
| Парткод: | FM1-B859-000 |
| Деталь: | SCREW, MACH. PAN HEAD, M3X4 |
| Парткод: | XA9-1979-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | NPN |
| Деталь: | PLATE, FIXING FIXED |
| Парткод: | FE3-1342-000 |
| Деталь: | PLATE, FIXING POSITIONING |
| Парткод: | FE3-0837-000 |
| Деталь: | PLATE, ADJUST |
| Парткод: | FE4-0262-000 |
| Деталь: | BUSHING |
| Парткод: | FE4-1488-000 |
| Деталь: | FIXING DRAWER ASSEMBLY |
| Парткод: | FM1-B665-000 |
| Деталь: | TRAY DUCT ASSEMBLY, LOWER |
| Парткод: | FM1-G730-000 |
| Деталь: | ROWEL BLOCK ASSEMBLY |
| Парткод: | FM1-G731-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0148-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | CORD, POWER SUPPLY |
| Парткод: | FK3-2055-000 |
| Деталь: | CABLE, INLET |
| Парткод: | FM1-D848-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | WASHER, TOOTHED LOCK, M4 |
| Парткод: | XD1-4200-402 |
| Деталь: | POWER CORD TERMINAL ASSEMBLY |
| Парткод: | NPN |
| Деталь: | HOLDER, FAN |
| Парткод: | FE3-0845-000 |
| Деталь: | FAN |
| Парткод: | FK2-0360-000 |
| Цена: | 1 600 ₽ |
| Деталь: | POWER SUPPLY FAN ASSEMBLY |
| Парткод: | NPN |
| Деталь: | BUSHING |
| Парткод: | FC0-5888-000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FE3-1092-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FE3-1409-000 |
| Деталь: | HOLDER, PUSHING SPRING |
| Парткод: | FE3-5661-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-5662-000 |
| Деталь: | GUIDE, EXTRACTION ROLLER |
| Парткод: | FE3-9566-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-9567-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-9568-000 |
| Деталь: | STOPPER, UPPER |
| Парткод: | FE3-9569-000 |
| Деталь: | STOPPER, LOWER |
| Парткод: | FE3-9570-000 |
| Деталь: | LABEL, DUPLEXING GUIDE HANDLE |
| Парткод: | FE3-9855-000 |
| Деталь: | PLATE, PUSHING |
| Парткод: | FE4-1748-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE4-1751-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE4-1884-000 |
| Деталь: | ROLLER, EXTRACTION |
| Парткод: | FL0-3975-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FL0-3980-000 |
| Деталь: | SECONDARY TRANSFER ASSEMBLY |
| Парткод: | FM1-B208-000 |
| Деталь: | GUIDE, CONDUCTIVE |
| Парткод: | FE2-2117-000 |
| Деталь: | LEVER, ESTRANGEMENT, FRONT |
| Парткод: | FE3-1089-000 |
| Деталь: | LEVER, ESTRANGEMENT, REAR |
| Парткод: | FE3-1090-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE4-5343-000 |
| Деталь: | ROLLER GUIDE ASSEMBLY |
| Парткод: | FM1-D183-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FE3-5393-000 |
| Деталь: | COVER,STATIC CHARGE ELIMINATOR |
| Парткод: | FE4-5342-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0086-000 |
| Деталь: | SPRING, HIGH VOLTAGE |
| Парткод: | FU2-0087-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0166-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1110-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1578-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU2-0094-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0165-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-0167-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-0168-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-1060-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1061-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1283-000 |
| Деталь: | DUPLEXING GUIDE ASSEMBLY |
| Парткод: | NPN |
| Деталь: | ROLLER, DUPLEXING |
| Парткод: | FC0-5873-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5888-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FE4-8959-000 |
| Деталь: | COVER, DRIVE GEAR, FRONT |
| Парткод: | FE3-1112-000 |
| Деталь: | FLAG, SENSOR |
| Парткод: | FE3-1125-000 |
| Деталь: | SHAFT, TRANSMISSION |
| Парткод: | FE3-1134-000 |
| Деталь: | COVER, DRIVE GEAR, REAR |
| Парткод: | FE3-1135-000 |
| Деталь: | LEVER |
| Парткод: | FE3-1136-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FE3-1392-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-9443-000 |
| Деталь: | HOLDER, ROLLER SHAFT |
| Парткод: | FE3-9444-000 |
| Деталь: | RING, O |
| Парткод: | FE4-0668-000 |
| Деталь: | ROLLER |
| Парткод: | FE4-0669-000 |
| Деталь: | HOLDER, ROLLER RING |
| Парткод: | FE4-0671-000 |
| Деталь: | ROLLER, PAPER DELIVERY |
| Парткод: | FL0-0139-000 |
| Деталь: | FLAPPER,2ND/3RD PAPER DELIVERY |
| Парткод: | FL0-0813-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-1505-000 |
| Деталь: | ROLLER, DUPLEXING FEED |
| Парткод: | FL3-6443-000 |
| Деталь: | ONE-WAY GEAR ASSEMBLY |
| Парткод: | FM1-B276-000 |
| Деталь: | GEAR, 21T |
| Парткод: | FU2-0094-000 |
| Деталь: | GEAR, 26T |
| Парткод: | FU2-0096-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0179-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0180-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0181-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0182-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0710-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0713-000 |
| Деталь: | SHAFT, ROLLER |
| Парткод: | FE3-1401-000 |
| Деталь: | THIRD PAPER DELIVERY ASSEMBLY |
| Парткод: | FM1-B275-000 |
| Деталь: | LEVER, TOGGLE |
| Парткод: | FE2-2086-000 |
| Деталь: | PLATE, READER JOINT |
| Парткод: | FE3-0768-000 |
| Деталь: | ARM, LOCK |
| Парткод: | FE3-0968-000 |
| Деталь: | ROLLER, RAIL |
| Парткод: | FE3-1352-000 |
| Деталь: | HINGE, FRONT |
| Парткод: | FE3-1421-000 |
| Деталь: | HINGE, REAR |
| Парткод: | FE3-1422-000 |
| Деталь: | SUPPORT, CASSETTE ROLLER, RT. |
| Парткод: | FE3-2466-000 |
| Деталь: | SHEET, CLAMP |
| Парткод: | FE3-3613-000 |
| Деталь: | STOPPER |
| Парткод: | FE3-8415-000 |
| Деталь: | STOPPER, SLIDE, LEFT |
| Парткод: | FE3-9457-000 |
| Деталь: | STOPPER, SLIDE, RIGHT |
| Парткод: | FE3-9458-000 |
| Деталь: | PLATE, READER MOUNTING |
| Парткод: | FE3-9502-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FE3-9853-000 |
| Деталь: | SPACER, SWITCH |
| Парткод: | FE4-1476-000 |
| Деталь: | ROLLER, RAIL |
| Парткод: | FE4-8808-000 |
| Деталь: | SWITCH, MAIN POWER SUPPLY |
| Парткод: | FK3-2835-000 |
| Деталь: | CABLE, CONTROL PANEL ASSEMBLY |
| Парткод: | FK4-0323-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK4-0324-000 |
| Деталь: | ENVIRONMENT SENSOR ASSEMBLY |
| Парткод: | FM1-D282-000 |
| Деталь: | CABLE, POWER SUPPLY |
| Парткод: | FM1-D851-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-0957-000 |
| Деталь: | SWITCH, PUSH |
| Парткод: | WC2-5806-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | LABEL, QUICK START CAUTION |
| Парткод: | FE3-9859-000 |
| Деталь: | CABLE, SATA POWER |
| Парткод: | FK4-0275-000 |
| Деталь: | CABLE, SATA SIGNAL |
| Парткод: | FK4-0276-000 |
| Деталь: | HARD DISK DRIVE, MQ01ABF032 |
| Парткод: | FK4-1550-000 |
| Деталь: | SWITCH, PUSH |
| Парткод: | WC2-5806-000 |
| Деталь: | DEVELOPING H.V. GUIDE ASSEMBLY |
| Парткод: | FM1-B217-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, C |
| Парткод: | FM1-B218-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, BK |
| Парткод: | FM1-B219-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, Y |
| Парткод: | FM1-B220-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, M |
| Парткод: | FM1-B221-000 |
| Деталь: | INTERLOCK SWITCH ASSEMBLY |
| Парткод: | FM1-B227-000 |
| Деталь: | MULTI REEL ASSEMBLY |
| Парткод: | FM1-C283-000 |
| Деталь: | CABLE, AC DRIVER |
| Парткод: | FM1-D811-000 |
| Деталь: | CABLE, HEATER |
| Парткод: | FM1-D815-000 |
| Деталь: | CABLE, DDIP |
| Парткод: | FM1-D818-000 |
| Деталь: | CABLE, FEED |
| Парткод: | FM1-D824-000 |
| Деталь: | CABLE, PICK-UP |
| Парткод: | FM1-D827-000 |
| Деталь: | CABLE, ECO-ID |
| Парткод: | FM1-D841-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | CONNECTOR, SNAP TIGHT, W |
| Парткод: | VS1-7440-011 |
| Деталь: | CONNECTOR, SNAP TIGHT, W |
| Парткод: | VS1-7504-015 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | DAMPER, CUSHION |
| Парткод: | XH9-0149-000 |
| Деталь: | SPACER |
| Парткод: | XZ1-1301-005 |
| Деталь: | MACHINE REAR PLATE 1 |
| Парткод: | NPN |
| Деталь: | CAP |
| Парткод: | FC0-0695-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FC0-2633-000 |
| Деталь: | STOPPER |
| Парткод: | FE4-2085-000 |
| Деталь: | HOOK, COVER, FRONT |
| Парткод: | FC8-8205-000 |
| Деталь: | GLASS CLEANING ROD ASSEMBLY |
| Парткод: | FM3-5968-010 |
| Деталь: | GUIDE, TRAY |
| Парткод: | FE3-0424-000 |
| Деталь: | COVER, POWER SUPPLY CORD |
| Парткод: | FE3-0815-000 |
| Деталь: | COVER, HANDLE |
| Парткод: | FE3-0851-000 |
| Деталь: | COVER,MAIN POWER SUPPLY SWITCH |
| Парткод: | FE3-0902-000 |
| Деталь: | COVER, RIGHT, FRONT LOWER |
| Парткод: | FE3-0903-000 |
| Деталь: | COVER, RIGHT, FRONT UPPER |
| Парткод: | FE3-0904-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FE3-0907-000 |
| Деталь: | COVER, RIGHT, REAR UPPER |
| Парткод: | FE3-0908-000 |
| Деталь: | COVER, INNER CONNECTOR |
| Парткод: | FE3-0909-000 |
| Деталь: | COVER, RIGHT, LOWER |
| Парткод: | FE3-0911-000 |
| Деталь: | COVER, LEFT, UPPER |
| Парткод: | FE3-0913-000 |
| Деталь: | COVER, LEFT, LOWER |
| Парткод: | FE3-0914-000 |
| Деталь: | RIGHT FRONT UP. COVER ASSEMBLY |
| Парткод: | FE3-0915-000 |
| Деталь: | COVER, INNER, DELV. REAR |
| Парткод: | FE3-0917-000 |
| Деталь: | COVER, HARD DISK DRIVE |
| Парткод: | FE3-0918-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FE3-0919-000 |
| Деталь: | COVER, LEFT, UPPER |
| Парткод: | FE3-0920-000 |
| Деталь: | COVER, INNER, RIGHT |
| Парткод: | FE3-0921-000 |
| Деталь: | COVER, WASTE TONER ASSEMBLY |
| Парткод: | FE3-1060-000 |
| Деталь: | PLATE, FIXED |
| Парткод: | FE3-2472-000 |
| Деталь: | COVER, SUPPORT, LOWER |
| Парткод: | FE3-1338-000 |
| Деталь: | COVER, SUPPORT, SMALL |
| Парткод: | FE3-1339-000 |
| Деталь: | COVER, SUPPORT HINGE, INNER |
| Парткод: | FE3-1340-000 |
| Деталь: | TRAY, FIRST PAPER DELIVERY |
| Парткод: | FE3-1395-000 |
| Деталь: | SHAFT, HINGE |
| Парткод: | FE3-2485-000 |
| Деталь: | COVER, FRONT |
| Парткод: | FE3-1464-000 |
| Деталь: | COVER, SUPPORT HINGE, RIGHT |
| Парткод: | FE3-2481-000 |
| Деталь: | COVER, SUPPORT, REAR |
| Парткод: | FE3-2482-000 |
| Деталь: | GUIDE, REVERSE BACK END |
| Парткод: | FE3-9167-000 |
| Деталь: | COVER, CONNECTOR |
| Парткод: | FE3-9168-000 |
| Деталь: | CAP |
| Парткод: | FE3-9169-000 |
| Деталь: | COVER, THIRD PAPER DELIVERY |
| Парткод: | FE3-9450-000 |
| Деталь: | LABEL, FRONT COVER |
| Парткод: | FE3-9829-000 |
| Деталь: | SUPPORT, PAPER DELIVERY TRAY |
| Парткод: | FE4-7425-000 |
| Деталь: | STOPPER, PUSHING |
| Парткод: | FE4-5318-000 |
| Деталь: | COVER, FRONT UPPER |
| Парткод: | FL0-4915-000 |
| Деталь: | PAD, GLASS CLEANING |
| Парткод: | FL2-9476-000 |
| Деталь: | EMBLEM |
| Парткод: | FL3-1185-000 |
| Деталь: | RIGHT COVER ASSEMBLY, RR. LW. |
| Парткод: | FM1-B195-000 |
| Деталь: | LEFT COVER ASSEMBLY, REAR |
| Парткод: | FM1-C123-000 |
| Деталь: | LABEL, MULTIPLE |
| Парткод: | FE3-9848-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FC8-8346-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, ENV. HEATER SWITCH |
| Парткод: | FC8-4137-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-G728-000 |
| Деталь: | TPM PCB ASSEMBLY |
| Парткод: | FM1-B859-000 |
| Деталь: | SCREW, MACH. PAN HEAD, M3X4 |
| Парткод: | XA9-1979-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | NPN |
| Деталь: | GEAR, 14T |
| Парткод: | FC8-4990-000 |
| Деталь: | PLATE, FREE STOP |
| Парткод: | FE2-0026-010 |
| Деталь: | PLATE, PAPER SIDE END, REAR |
| Парткод: | FE3-0478-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-0483-000 |
| Деталь: | COVER, CASSETTE FRONT |
| Парткод: | FE3-1505-000 |
| Деталь: | CAM, BACK END DETECT |
| Парткод: | FE3-1524-000 |
| Деталь: | LINK, SIZE DETECT |
| Парткод: | FE3-1525-000 |
| Деталь: | ARM, BACK END DETECT |
| Парткод: | FE3-1526-000 |
| Деталь: | GEAR, 68T/37T |
| Парткод: | FE3-1527-000 |
| Деталь: | ROLLER, CASSETTE |
| Парткод: | FE3-1528-000 |
| Деталь: | RACK, LINK |
| Парткод: | FE3-6546-000 |
| Деталь: | PIN, ARM |
| Парткод: | FE3-8283-000 |
| Деталь: | SPACER |
| Парткод: | FE3-8412-000 |
| Деталь: | SHAFT, DAMPER |
| Парткод: | FE3-8418-000 |
| Деталь: | ARM, GUIDE |
| Парткод: | FE4-1502-000 |
| Деталь: | PIN, GUIDE |
| Парткод: | FE4-1836-000 |
| Деталь: | HANDLE, CST. FRONT COVER |
| Парткод: | FE4-1841-000 |
| Деталь: | HOLDER, DAMPER |
| Парткод: | FE4-1845-000 |
| Деталь: | PLATE, LINK |
| Парткод: | FE4-5920-000 |
| Деталь: | PLATE, LIFTING |
| Парткод: | FL0-0900-000 |
| Деталь: | SHEET, SEPARATION |
| Парткод: | FL0-4008-000 |
| Деталь: | SIDE END PLATE ASSEMBLY, FRONT |
| Парткод: | FM1-B243-000 |
| Деталь: | BACK END LIMIT ASSEMBLY |
| Парткод: | FM1-D257-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1081-000 |
| Деталь: | LABEL, CASSETTE |
| Парткод: | FU2-1224-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1278-000 |
| Деталь: | GEAR, 14T |
| Парткод: | RC1-9396-000 |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-1523-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0337-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0359-000 |
| Деталь: | CASSETTE ASSEMBLY |
| Парткод: | FM1-B242-000 |
| Деталь: | WASTE TONER FEED ASSEMBLY |
| Парткод: | FM1-B247-000 |
| Деталь: | MULTI PAPER PICK-UP ASSEMBLY |
| Парткод: | FM1-B666-000 |
| Деталь: | SHAFT, ROLLER |
| Парткод: | FE3-0387-000 |
| Деталь: | CAM, ROLLER ESTRANGEMENT |
| Парткод: | FE3-0441-000 |
| Деталь: | LINK, RELEASE |
| Парткод: | FE3-0442-000 |
| Деталь: | HOLDER, SEPARATION ROLLER |
| Парткод: | FE3-1559-000 |
| Деталь: | LEVER, PAPER PRESENCE DETECT |
| Парткод: | FE3-1648-000 |
| Деталь: | ROLLER |
| Парткод: | FE4-0324-000 |
| Деталь: | LIMITTER, TORQUE |
| Парткод: | FE4-1528-000 |
| Деталь: | COVER, SEPARATION ROLLER |
| Парткод: | FL0-1152-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1674-000 |
| Цена: | 5 000 ₽ |
| Деталь: | CABLE, M.P. PICK UP SENSOR |
| Парткод: | FM1-D854-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-006 |
| Деталь: | CAM/GEAR, 35T |
| Парткод: | FU2-0261-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-0263-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0264-000 |
| Деталь: | GEAR, 19T/26T |
| Парткод: | FU2-0450-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | COVER, GEAR |
| Парткод: | FE3-0435-000 |
| Деталь: | COVER, GEAR |
| Парткод: | FC0-7444-000 |
| Деталь: | LINK, RELEASE |
| Парткод: | FE4-8807-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-0444-000 |
| Деталь: | COVER, ROLLER |
| Парткод: | FE3-1541-000 |
| Деталь: | SHAFT, ROLLER |
| Парткод: | FE3-1553-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-1617-000 |
| Деталь: | GUIDE, SHUTTER LINK |
| Парткод: | FE3-4759-000 |
| Деталь: | SHUTTER, PAPER PICK-UP |
| Парткод: | FE3-4760-000 |
| Деталь: | LOCK, SHUTTER |
| Парткод: | FE3-4761-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FE8-1276-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE4-0617-000 |
| Деталь: | LEVER, SHUTTER LINK |
| Парткод: | FE4-1829-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FE4-1832-000 |
| Деталь: | SHAFT, ROLLER |
| Парткод: | FE4-1835-000 |
| Деталь: | CLUTCH, ONE-WAY |
| Парткод: | FL0-1361-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-4002-000 |
| Цена: | 4 900 ₽ |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0219-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU2-0257-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0265-000 |
| Деталь: | ONE-WAY GEAR ASSEMBLY |
| Парткод: | FM1-B214-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU2-0251-000 |
| Деталь: | GEAR, 25T/22T |
| Парткод: | FU2-0253-000 |
| Деталь: | MULTI PAPER PICK-UP ASSEMBLY |
| Парткод: | NPN |
| Деталь: | DEVELOPING ASSEMBLY, Y |
| Парткод: | FM1-B264-000 |
| Деталь: | DEVELOPING ASSEMBLY, M |
| Парткод: | FM1-B265-000 |
| Деталь: | DEVELOPING ASSEMBLY,C |
| Парткод: | FM1-B266-000 |
| Деталь: | DEVELOPING ASSEMBLY, BK |
| Парткод: | FM1-B267-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | DEVELOPING ASSEMBLY |
| Парткод: | NPN |
| Деталь: | HANDLE, WASTE TONER CASE |
| Парткод: | FE3-1068-000 |
| Деталь: | WINDOW, WASTE TONER CASE |
| Парткод: | FL0-7007-000 |
| Деталь: | CONTAINER, WASTE TONER, WT-202 |
| Парткод: | FM1-A606-000 |
| Деталь: | LABEL, QUICK START CAUTION |
| Парткод: | FE3-9859-000 |
| Деталь: | CABLE, SATA POWER |
| Парткод: | FK4-0275-000 |
| Деталь: | CABLE, SATA SIGNAL |
| Парткод: | FK4-0276-000 |
| Деталь: | HARD DISK DRIVE, MQ01ABF032 |
| Парткод: | FK4-1550-000 |
| Деталь: | SWITCH, PUSH |
| Парткод: | WC2-5806-000 |
| Деталь: | DEVELOPING H.V. GUIDE ASSEMBLY |
| Парткод: | FM1-B217-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, C |
| Парткод: | FM1-B218-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, BK |
| Парткод: | FM1-B219-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, Y |
| Парткод: | FM1-B220-000 |
| Деталь: | CORONA H.V. GUIDE ASSEMBLY, M |
| Парткод: | FM1-B221-000 |
| Деталь: | INTERLOCK SWITCH ASSEMBLY |
| Парткод: | FM1-B227-000 |
| Деталь: | MULTI REEL ASSEMBLY |
| Парткод: | FM1-C283-000 |
| Деталь: | CABLE, AC DRIVER |
| Парткод: | FM1-D811-000 |
| Деталь: | CABLE, HEATER |
| Парткод: | FM1-D815-000 |
| Деталь: | CABLE, DDIP |
| Парткод: | FM1-D818-000 |
| Деталь: | CABLE, FEED |
| Парткод: | FM1-D824-000 |
| Деталь: | CABLE, PICK-UP |
| Парткод: | FM1-D827-000 |
| Деталь: | CABLE, ECO-ID |
| Парткод: | FM1-D841-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | CONNECTOR, SNAP TIGHT, W |
| Парткод: | VS1-7440-011 |
| Деталь: | CONNECTOR, SNAP TIGHT, W |
| Парткод: | VS1-7504-015 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | DAMPER, CUSHION |
| Парткод: | XH9-0149-000 |
| Деталь: | SPACER |
| Парткод: | XZ1-1301-005 |
| Деталь: | MACHINE REAR PLATE 1 |
| Парткод: | NPN |
Коды ошибок
E001 0001
E001 0002
E002 0002
E002 0003
E002 0004
E003 0004
E003 0005
E003 0006
E004 0001
E004 0002
E009 0000
E009 0001
E010 0001
E010 0002
E010 0003
E012 0001
E012 0002
E012 0003
E013 0001
E014 0001
E014 0002
E014 0003
E020 01A8
E020 01B8
E020 01C8
E020 02A8
E020 02B8
E020 02C8
E020 03A8
E020 03B8
E020 03C8
E020 04A8
E020 04B8
E021 0001
E021 0002
E021 0120
E021 0220
E021 0320
E021 0420
E025 0110
E025 0120
E025 0168
E025 0210
E025 0220
E025 0268
E025 0310
E025 0320
E025 0368
E025 0410
E025 0420
E025 0468
E029 5008
E029 7008
E073 0001
E074 0001
E074 0002
E100 0001
E110 0001
E110 0002
E110 0003
E110 0004
E193 0001
E196 0000
E196 0001
E196 000F
E196 0100
E196 0101
E196 010F
E196 0800
E196 0801
E196 080F
E197 0B11
E197 0B20
E197 0B21
E197 1001
E197 1002
E197 1004
E197 1081
E197 1082
E197 1084
E197 5000
E197 5001
E202 0001
E202 0002
E202 0003
E227 0001
E227 0101
E240 0000
E246 0001
E246 0002
E246 0003
E246 0005
E247 0001
E247 0002
E247 0003
E248 0001
E260 0001
E260 0002
E270 0001
E270 0002
E280 0001
E280 0002
E280 0003
E280 0004
E302 0001
E302 0002
E315 0007
E315 000D
E315 000E
E315 000F
E315 0027
E315 0035
E315 0100
E315 0500
E315 0501
E315 0510
E315 0511
E315 0520
E315 0521
E315 0530
E315 0531
E315 0540
E315 0541
E315 0550
E315 0551
E350 0000
E350 0001
E350 0002
E350 0003
E350 3000
E351 0000
E354 0001
E354 0002
E355 0001
E355 0002
E355 0003
E355 0004
E400 0002
E500 0000
E501 0091
E503 0002
E505 0001
E505 0004
E514 0002
E514 8001
E514 8002
E516 0001
E516 0002
E530 8001
E530 8002
E531 8001
E531 8002
E532 8001
E532 8002
E535 0001
E535 0002
E535 8001
E535 8002
E537 8001
E537 8002
E540 8001
E540 8002
E540 8003
E542 8001
E542 8002
E551 0001
E551 0002
E551 0003
E551 0004
E577 0002
E577 8001
E584 0002
E584 8001
E5F0 8001
E5F0 8002
E5F1 8001
E5F1 8002
E5F2 8001
E5F2 8002
E5F3 8001
E5F3 8002
E5F4 8001
E5F4 8002
E5F5 8001
E5F5 8002
E5F6 8001
E5F6 8002
E5F6 8003
E5F6 8004
E5F6 8005
E602 0001
E602 0101
E602 0111
E602 0201
E602 0211
E602 0301
E602 0311
E602 0401
E602 0411
E602 0501
E602 0511
E614 0001
E614 0002
E614 0006
E614 0101
E614 0111
E614 0201
E614 0211
E614 0301
E614 0311
E614 0401
E614 0411
E614 0501
E614 0511
E614 0601
E614 0611
E614 0701
E614 0711
E614 4000
E615 0001
E674 0001
E674 0004
E674 0008
E674 000C
E674 0010
E674 0011
E674 0020
E674 0100
E674 0200
E713 0010
E713 0011
E713 0020
E713 0021
E713 0022
E713 0030
E719 0001
E719 0002
E719 0003
E719 0031
E719 0032
E720 0001
E730 A006
E730 A007
E730 B013
E732 0001
E732 0010
E733 0000
E733 0001
E733 0002
E733 0F01
E733 0F02
E733 F001
E733 F002
E743 0001
E744 0001
E744 4000
E746 0022
E746 0023
E746 0024
E746 0031
E746 0032
E746 0033
E746 0034
E746 0035
E748 2010
E748 9000
E749 0005
E749 0006
E753 0001
E804 0000
E806 0100
E806 0101
E806 0200
E806 0201
E808 0001
E808 0002
E811 0000
E880 0001
E881 0001
E890 0001
E890 0002
E890 0003
E996 0071
E996 0CA1
E996 0CA2
E996 0CA3
E996 0CA4
E996 0CA5
E996 0CA6
E996 0CA7
E996 0CA8
E996 0CAE
E996 0CAF
E996 0CB0
E996 0CB3
E996 0CB4
E996 0CB6
E996 0CB8
E996 0CF0
E996 0CF3
E996 0CF4
E996 0CF5
Описание
| Error code: | E001 0001 |
| Description: | Abnormal high temperature in fixing (The sub thermistor detected a temperature of higher than 290 degree C. |
| Causes: | Abnormally high temperature detected by sub thermistor (sub thermistor triggered) |
| Remedy: | 1) Reconnect the connector on the Engine Controller PCB. 2) Turn OFF the power supply switch, and remove the Fixing Assembly. Measure the resistance value between the connector (FSRTH) at the Fixing Assembly side and grounding. If the resistance value is 1k ohm or lower, replace the Fixing Assembly. 3) Replace the Engine Controller PCB. |
| Error code: | E001 0002 |
| Description: | Fixing Sub Thermistor (Front) high temperature detection error. The Fixing Sub Thermistor (Front) in the Fixing Unit detected 295 deg C or higher for 0.2 sec or longer. |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E002 0002 |
| Description: | Fixing Sub Thermistor (Front) open circuit detection error. The Fixing Sub Thermistor (Front) detected a temperature of 40 deg C or lower for 3 sec or longer from when the Fixing Heater was turned ON until start of PI control |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E002 0003 |
| Description: | Fixing Sub Thermistor (Rear) open circuit detection error. The Fixing Sub Thermistor (Rear) detected a temperature of 40 deg C or lower for 3 sec or longer from when the Fixing Heater was turned ON until start of PI control. |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E002 0004 |
| Description: | Fixing Main Thermistor temperature increase detection error. The Fixing Main Thermistor detected a temperature increase of 1 deg C for less than 5 sec from when the Fixing Heater was turned ON until start of PI control. |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E003 0004 |
| Description: | Fixing Main Thermistor low temperature detection error.The Fixing Main Thermistor detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater was turned OFF). |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E003 0005 |
| Description: | Fixing Sub Thermistor (Front) low temperature detection error. The Fixing Sub Thermistor (Front) detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater was turned OFF). |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E003 0006 |
| Description: | Fixing Sub Thermistor (Rear) low temperature detection error. The Fixing Sub Thermistor (Rear) detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater was turned OFF). |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the remedy work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E004 0001 |
| Description: | Fixing Relay welding detection error |
| Causes: | Zero cross interruption was detected although the Fixing Relay was not turned ON. |
| Remedy: | [Remedy] Replace the Low-voltage Power Supply PCB. (Unit of replacement: POWER SUPPLY ASSEMBLY) [Caution] Since an electrical trouble due to error in fixing safety circuit relay is the cause of the error, be sure to replace the Low-voltage Power Supply PCB. |
| Error code: | E004 0002 |
| Description: | Fixing Main Thermistor and Fixing Sub Thermistor (Rear) disconnection detection error |
| Causes: | Connection could not be detected within 0.5 sec when power was supplied to the Fixing Heater. |
| Remedy: | [Related parts] • Fixing Assembly (Unit of replacement: Fixing Assembly) • Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E009 0000 |
| Description: | Fixing pressure timeout error. The Fixing Pressure Release Sensor did not detect ON status within 10 sec after the start of pressure application operation for fixing. |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Fixing Pressure Release Sensor 1. DC Controller PCB (UN04/J122) to Relay Connector (11P) (Unit of replacement: CABLE, FEED) 2. Relay Connector (11P) to Fixing Pressure Release Sensor (PS13) (Unit of replacement: PAPER DELIVERY DRIVE ASSEMBLY) • Harnesses from the DC Controller PCB to the Fixing Motor 1. DC Controller PCB (UN04/J122) to Relay Connector (8P) (Unit of replacement: CABLE, FEED) 2. Relay Connector (8P) to Fixing Motor (M09) (Unit of replacement: FIXING DRIVE MOTOR ASSEMBLY) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Fixing Pressure Release Sensor (PS13) • Fixing Drive Unit (Unit of replacement: FIXING DRIVE ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E009 0001 |
| Description: | Fixing pressure timeout error |
| Causes: | Signal of the Fixing Pressure Release Sensor could not be detected at pressure application operation of the Fixing Pressure Release Cam, and the operation was not completed within 4 sec from the start of counterclockwise rotation of the Fixing Motor. |
| Remedy: | [Related parts] • Fixing Assembly (Unit of replacement: Fixing Assembly) • Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) • Harness between the DC Controller PCB (UN04/J135) and the Fixing Motor (M04/J5412) (Unit of replacement: CABLE, FIXING DRIVE) • Harness between the Fixing Drawer (DR01/J5401) and the Fixing Pressure Release Sensor (PS13/J5403) (Unit of replacement: CABLE, FIXING ASSEMBLY) • Fixing Pressure Release Sensor (PS13) (Unit of replacement: PHOTO INTERRUPTER) • Fixing Drive Unit (Unit of replacement: FIXING DRIVE ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E010 0001 |
| Description: | Bk Drum_ITB Motor error |
| Causes: | It did not become the specified speed for 500 consecutive msec although 1000 msec have passed from the startup of the Bk Drum_ITB Motor in the Main Drive Unit. (The detection timing varies depending on the paper feed conditions.) |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Harnesses connecting the Bk Drum_ITB Motor (M02/J5702), the Relay Connector (8P) and the DC Controller PCB (UN04/J140) (Unit of replacement: MAIN DRIVE ASSEMBLY) • Fuse in the Low-voltage Power Supply PCB (UN01/FU14) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Bk Drum_ITB Motor (M02) (Unit of replacement: MOTOR, DC) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] It is highly possible that the Bk Drum_ITB Motor is not rotating due to overload or an electrical trouble. Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harnesses from the Bk Drum_ITB Motor to the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the Bk Drum_ITB Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Low-voltage Power Supply PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER > FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER > FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E010 0002 |
| Description: | Bk Drum_ITB Motor error |
| Causes: | The specified speed could not be detected for 500 consecutive msec although it became the specified speed at least once from the startup of the Bk Drum_ITB Motor in the Main Drive Unit. |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Harnesses connecting the Bk Drum_ITB Motor (M02/J5702), the Relay Connector (8P) and the DC Controller PCB (UN04/J140) (Unit of replacement: MAIN DRIVE ASSEMBLY) • Fuse in the Low-voltage Power Supply PCB (UN01/FU14) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Bk Drum_ITB Motor (M02) (Unit of replacement: MOTOR, DC) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] It is highly possible that the Bk Drum_ITB Motor is not rotating due to overload or an electrical trouble. Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harnesses from the Bk Drum_ITB Motor to the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the Bk Drum_ITB Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Low-voltage Power Supply PCB. |
| Error code: | E010 0003 |
| Description: | Bk Drum_ITB Motor error |
| Causes: | There was no FG signal input for 300 msec from the startup of the Bk Drum_ITB Motor in the Main Drive Unit. |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Harnesses connecting the Bk Drum_ITB Motor (M02/J5702), the Relay Connector (8P) and the DC Controller PCB (UN04/J140) (Unit of replacement: MAIN DRIVE ASSEMBLY) • Fuse in the Low-voltage Power Supply PCB (UN01/FU14) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Bk Drum_ITB Motor (M02) (Unit of replacement: MOTOR, DC) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] It is highly possible that the Bk Drum_ITB Motor is not rotating due to overload or an electrical trouble. Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harnesses from the Bk Drum_ITB Motor to the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the Bk Drum_ITB Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Low-voltage Power Supply PCB. |
| Error code: | E012 0001 |
| Description: | Black drum motor error (Failure in drum motor rotation) The motor rotated out of the target speed during rotation after the target speed was reached. |
| Causes: | Error in ITB motor rotation after attaining the target rotation detected based on ITB motor speed detection signal |
| Remedy: | 1) Reconnect the connector on the Main Motor 2) Replace the Engine Controller PCB. |
| Error code: | E012 0002 |
| Description: | CL Drum Motor error |
| Causes: | The specified speed could not be detected for 500 consecutive msec although it became the specified speed at least once from the startup of the CL Drum Motor in the Main Drive Unit. |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Harness between the CL Drum Motor (M01/J5701) and the DC Controller PCB (UN04/J140) (Unit of replacement: MAIN DRIVE ASSEMBLY) • Fuse in the Low-voltage Power Supply PCB (UN01/FU14) (Unit of replacement: POWER SUPPLY ASSEMBLY) • CL Drum Motor (M01) (Unit of replacement: MOTOR, DC) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] It is highly possible that the CL Drum Motor is not rotating due to overload or an electrical trouble. Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the CL Drum Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the CL Drum Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Low-voltage Power Supply PCB. |
| Error code: | E012 0003 |
| Description: | CL Drum Motor error |
| Causes: | There was no FG signal input for 300 msec from the startup of the CL Drum Motor in the Main Drive Unit. |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Harness between the CL Drum Motor (M01/J5701) and the DC Controller PCB (UN04/J140) (Unit of replacement: MAIN DRIVE ASSEMBLY) • Fuse in the Low-voltage Power Supply PCB (UN01/FU14) (Unit of replacement: POWER SUPPLY ASSEMBLY) • CL Drum Motor (M01) (Unit of replacement: MOTOR, DC) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] It is highly possible that the CL Drum Motor is not rotating due to overload or an electrical trouble. Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the CL Drum Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the CL Drum Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Low-voltage Power Supply PCB. |
| Error code: | E013 0001 |
| Description: | Waste Toner Feed Motor error. After rotation speed of the Waste Toner Feed Motor was detected when the motor was driven, it was detected that the speed was not at the specified speed for 2 consecutive sec. |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Waste Toner Feed Motor 1. DC Controller PCB (UN04/J132) to Relay Connector (13P) (Unit of replacement: CABLE, CASSETTE SIZE) 2. Relay Connector (13P) to Waste Toner Feed Motor (J1044) (Unit of replacement: CABLE, WASTE TONER SENSOR) • Waste Toner Container (Unit of replacement: WASTE TONER CASE ASSEMBLY) • Waste Toner Feed Unit (Unit of replacement: WASTE TONER PAPER FEED ASS`Y) • Waste Toner Feed Motor (M17) (Unit of replacement: WASTE TONER PAPER FEED ASS`Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Pull out the Waste Toner Container to check if the toner in the container is full. If the waste toner is full, remove the toner clogged in the Waste Toner Pipe. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E014 0001 |
| Description: | Fixing Motor rotation error |
| Causes: | Error in fixing motor rotation after attaining the target rotation detected based on fixing motor speed detection signal. |
| Remedy: | 1) Reconnect the connector on the Fixing Motor 2) Replace the Fixing Motor |
| Error code: | E014 0002 |
| Description: | Fixing motor (M3) pressure releasing error |
| Causes: | "Speed lock signal =0" is detected more than 1.0 sec continuously after the fixing motor (M3) starts to drive and "Speed lock signal =1" is detected. |
| Remedy: | 1. Check connection to the fixing motor (M3). 2. Replace the fixing motor (M3). 3. Replace the engine controller PCB (PCB1). |
| Error code: | E014 0003 |
| Description: | Fixing motor (M3) pressure error |
| Causes: | Fixing pressure is never detected more than 3 sec or more by the fixing pressure release sensor (SR15/16) after fixing pressure drives. |
| Remedy: | 1. Check connection to the fixing motor (M3). 2. Replace the fixing motor (M3). 3. Replace the engine controller PCB (PCB1). |
| Error code: | E020 01A8 |
| Description: | ATR Sensor (Y)output error |
| Causes: | The output value of the ATR Sensor (Y) in the Drum Unit (Y) did not fall within the range from 10 or higher to 245 or less for 2 consecutive times during printing. |
| Remedy: | [Related parts] • ATR Sensor (Y) (UN34) (Unit of replacement: DEVE_UNIT_Y) • Drum Unit (Y) (Unit of replacement: DEVE_UNIT_Y) • Harness between the ATR Sensor (Y) (UN34/J6021) and the Drum Unit Memory PCB (Y) (UN12/J6011) (Unit of replacement: DEVE_UNIT_Y) • Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (Y) (UN08/J6001) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (Y) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E020 01B8 |
| Description: | ATR Sensor (Y) output error |
| Causes: | a. The output value of the ATR Sensor (Y) in the Drum Unit (Y) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times at initialization. b. The output value did not exceed 140 although the control voltage of the ATR Sensor (Y) in the Drum Unit (Y) was increased to 248 or higher, or it did not fall below 140 although the voltage was decreased to 8 at initialization. |
| Remedy: | [Related parts] • ATR Sensor (Y) (UN34) (Unit of replacement: DEVE_UNIT_Y) • Drum Unit (Y) (Unit of replacement: DEVE_UNIT_Y) • Harness between the ATR Sensor (Y) (UN34/J6021) and the Drum Unit Memory PCB (Y) (UN12/J6011) (Unit of replacement: DEVE_UNIT_Y) • Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (Y) (UN08/J6001) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (Y) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E020 01C8 |
| Description: | Error in take-up of Sealing Member (Y). The patch output value (SigR) failed to be 900 or less during initialization of the Developing Unit (Y). |
| Remedy: | [Related parts] • Harnesses from the Registration Patch Sensor Unit to the DC Controller PCB 1. Registration Patch Sensor Unit to Relay Connector (16P) (Unit of replacement: REGISTRATION SENSOR ASSEMBLY) 2. Relay Connector (16P) to DC Controller PCB (UN04/J120) (Unit of replacement: NEW OLD SENSING HOLDER ASS`Y) • Harness between the Secondary Transfer High Voltage PCB (UN03/J501 and J502) and the DC Controller PCB (UN04/J114 and J112) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB) • Registration Patch Sensor Unit (Unit of replacement: REGISTRATION SENSOR ASSEMBLY) • Developing Unit (Y) (Unit of replacement: DEVELOPING ASSEMBLY, Y) • Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRANSFER H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020 02A8 |
| Description: | ATR Sensor (M) output error |
| Causes: | The output value of the ATR Sensor (M) in the Drum Unit (M) did not fall within the range from 10 or higher to 245 or less for 2 consecutive times during printing. |
| Remedy: | [Related parts] • ATR Sensor (M) (UN35) (Unit of replacement: DEVE_UNIT_M) • Drum Unit (M) (Unit of replacement: DEVE_UNIT_M) • Harness between the ATR Sensor (M) (UN35/J6022) and the Drum Unit Memory PCB (M) (UN13/J6012) (Unit of replacement: DEVE_UNIT_M) • Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (M) (UN09/J6002) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (M) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E020 02B8 |
| Description: | ATR Sensor (M) output error |
| Causes: | a. The output value of the ATR Sensor (M) in the Drum Unit (M) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times at initialization. b. The output value did not exceed 140 although the control voltage of the ATR Sensor (M) in the Drum Unit (M) was increased to 248 or higher, or it did not fall below 140 although the voltage was decreased to 8 at initialization. |
| Remedy: | [Related parts] • ATR Sensor (M) (UN35) (Unit of replacement: DEVE_UNIT_M) • Drum Unit (M) (Unit of replacement: DEVE_UNIT_M) • Harness between the ATR Sensor (M) (UN35/J6022) and the Drum Unit Memory PCB (M) (UN13/J6012) (Unit of replacement: DEVE_UNIT_M) • Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (M) (UN09/J6002) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (M) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E020 02C8 |
| Description: | Error in take-up of Sealing Member (M). The patch output value (SigR) failed to be 900 or less during initialization of the Developing Unit (M). |
| Remedy: | [Related parts] • Harnesses from the Registration Patch Sensor Unit to the DC Controller PCB 1. Registration Patch Sensor Unit to Relay Connector (16P) (Unit of replacement: REGISTRATION SENSOR ASSEMBLY) 2. Relay Connector (16P) to DC Controller PCB (UN04/J120) (Unit of replacement: NEW OLD SENSING HOLDER ASS`Y) • Harness between the Secondary Transfer High Voltage PCB (UN03/J501 and J502) and the DC Controller PCB (UN04/J114 and J112) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB) • Registration Patch Sensor Unit (Unit of replacement: REGISTRATION SENSOR ASSEMBLY) • Developing Unit (M) (Unit of replacement: DEVELOPING ASSEMBLY, M) • Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRANSFER H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020 03A8 |
| Description: | ATR Sensor (C) output error |
| Causes: | The output value of the ATR Sensor (C) in the Drum Unit (C) did not fall within the range from 10 or higher to 245 or less for 2 consecutive times during printing. |
| Remedy: | [Related parts] • ATR Sensor (C) (UN36) (Unit of replacement: DEVE_UNIT_C) • Drum Unit (C) (Unit of replacement: DEVE_UNIT_C) • Harness between the ATR Sensor (C) (UN36/J6023) and the Drum Unit Memory PCB (C) (UN14/J6013) (Unit of replacement: DEVE_UNIT_C) • Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (C) (UN10/J6003) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (C) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E020 03B8 |
| Description: | ATR Sensor (C) output error |
| Causes: | a. The output value of the ATR Sensor (C) in the Drum Unit (C) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times at initialization. b. The output value did not exceed 140 although the control voltage of the ATR Sensor (C) in the Drum Unit (C) was increased to 248 or higher, or it did not fall below 140 although the voltage was decreased to 8 at initialization. |
| Remedy: | [Related parts] • ATR Sensor (C) (UN36) (Unit of replacement: DEVE_UNIT_C) • Drum Unit (C) (Unit of replacement: DEVE_UNIT_C) • Harness between the ATR Sensor (C) (UN36/J6023) and the Drum Unit Memory PCB (C) (UN14/J6013) (Unit of replacement: DEVE_UNIT_C) • Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (C) (UN10/J6003) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (C) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E020 03C8 |
| Description: | Error in take-up of Sealing Member (C). The patch output value (SigR) failed to be 900 or less during initialization of the Developing Unit (C). |
| Remedy: | [Related parts] • Harnesses from the Registration Patch Sensor Unit to the DC Controller PCB 1. Registration Patch Sensor Unit to Relay Connector (16P) (Unit of replacement: REGISTRATION SENSOR ASSEMBLY) 2. Relay Connector (16P) to DC Controller PCB (UN04/J120) (Unit of replacement: NEW OLD SENSING HOLDER ASS`Y) • Harness between the Secondary Transfer High Voltage PCB (UN03/J501 and J502) and the DC Controller PCB (UN04/J114 and J112) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB) • Registration Patch Sensor Unit (Unit of replacement: REGISTRATION SENSOR ASSEMBLY) • Developing Unit (C) (Unit of replacement: DEVELOPING ASSEMBLY, C) • Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRANSFER H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020 04A8 |
| Description: | ATR Sensor (Bk) output error |
| Causes: | The output value of the ATR Sensor (Bk) in the Drum Unit (Bk) did not fall within the range from 10 or higher to 245 or less for 2 consecutive times during printing. |
| Remedy: | [Related parts] • ATR Sensor (Bk) (UN37) (Unit of replacement: P-UNIT_BK) • Drum Unit (Bk) (Unit of replacement: P-UNIT_BK) • Harness between the ATR Sensor (Bk) (UN37/J6024) and the Drum Unit Memory PCB (Bk) (UN15/J6014) (Unit of replacement: P-UNIT_BK) • Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (Bk) (UN11/J6004) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (Bk) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E020 04B8 |
| Description: | ATR Sensor (Bk) output error |
| Causes: | a. The output value of the ATR Sensor (Bk) in the Drum Unit (Bk) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times at initialization. b. The output value did not exceed 140 although the control voltage of the ATR Sensor (Bk) in the Drum Unit (Bk) was increased to 248 or higher, or it did not fall below 140 although the voltage was decreased to 8 at initialization. |
| Remedy: | [Related parts] • ATR Sensor (Bk) (UN37) (Unit of replacement: P-UNIT_BK) • Drum Unit (Bk) (Unit of replacement: P-UNIT_BK) • Harness between the ATR Sensor (Bk) (UN37/J6024) and the Drum Unit Memory PCB (Bk) (UN15/J6014) (Unit of replacement: P-UNIT_BK) • Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (Bk) (UN11/J6004) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (Bk) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E021 0001 |
| Description: | Developing Motor error |
| Causes: | It did not become the specified speed for 500 consecutive msec although 1000 msec have passed from the startup of the Developing Motor. (The detection timing varies depending on the paper feed conditions.) |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Harness between the Developing Motor (M03) and the DC Controller PCB (UN04/J142) (Unit of replacement: MAIN DRIVE ASSEMBLY) • Fuse in the DC Controller PCB (UN04/FU4) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Developing Motor (M03) (Unit of replacement: MOTOR, DC) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] It is highly possible that the Developing Motor is not rotating due to overload or an electrical trouble. Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the Developing Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the Developing Motor. 2. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. |
| Error code: | E021 0002 |
| Description: | Developing Motor error |
| Causes: | The specified speed could not be detected for 500 consecutive msec although it became the specified speed at least once from the startup of the Developing Motor. |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Harness between the Developing Motor (M03) and the DC Controller PCB (UN04/J142) (Unit of replacement: MAIN DRIVE ASSEMBLY) • Fuse in the DC Controller PCB (UN04/FU4) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Developing Motor (M03) (Unit of replacement: MOTOR, DC) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] It is highly possible that the Developing Motor is not rotating due to overload or an electrical trouble. Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the Developing Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the Developing Motor. 2. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. |
| Error code: | E021 0120 |
| Description: | Developing Screw rotation detection error (Y) |
| Causes: | The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (Y) in the Drum Unit (Y) was 0.5 V or less. |
| Remedy: | [Related parts] • Drum Unit (Y) (Unit of replacement: DEVE_UNIT_Y) • Harness between the Drum Unit Relay PCB (Y) (UN08/J6001) and the DC Controller PCB (UN04/J160) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • Drum Unit Relay PCB (Y) (UN08) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • Drum Unit Memory PCB (Y) (UN12) (Unit of replacement: DEVE_UNIT_Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (Y) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E021 0220 |
| Description: | Developing Screw rotation detection error (M) |
| Causes: | The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (M) in the Drum Unit (M) was 0.5 V or less. |
| Remedy: | [Related parts] • Drum Unit (M) (Unit of replacement: DEVE_UNIT_M) • Harness between the Drum Unit Relay PCB (M) (UN09/J6002) and the DC Controller PCB (UN04/J160) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • Drum Unit Relay PCB (M) (UN09) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • Drum Unit Memory PCB (M) (UN13) (Unit of replacement: DEVE_UNIT_ M) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (M) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E021 0320 |
| Description: | Developing Screw rotation detection error (C) |
| Causes: | The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (C) in the Drum Unit (C) was 0.5 V or less. |
| Remedy: | [Related parts] • Drum Unit (C) (Unit of replacement: DEVE_UNIT_C) • Harness between the Drum Unit Relay PCB (C) (UN10/J6003) and the DC Controller PCB (UN04/J162) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • Drum Unit Relay PCB (C) (UN10) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • Drum Unit Memory PCB (C) (UN14) (Unit of replacement: DEVE_UNIT_C) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (C) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E021 0420 |
| Description: | Developing Screw rotation detection error (Bk) |
| Causes: | The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (Bk) in the Drum Unit (Bk) was 0.5 V or less. |
| Remedy: | [Related parts] • Drum Unit (Bk) (Unit of replacement: P-UNIT_BK) • Harness between the Drum Unit Relay PCB (Bk) (UN11/J6004) and the DC Controller PCB (UN04/J162) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • Drum Unit Relay PCB (Bk) (UN11) (Unit of replacement: PROCESS CONTROL PCB ASS’Y) • Drum Unit Memory PCB (Bk) (UN15) (Unit of replacement: P-UNIT_BK) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) [Points to note at work] • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. • If the Drum Unit Memory PCB (Bk) is soiled, clean it with a blower. [Remedy] Check/replace the related parts. |
| Error code: | E025 0110 |
| Description: | Bottle Motor (YM) error (Y) |
| Causes: | The Bottle Rotation Sensor (Y) did not detect rotation for 5 times in a row although 0.8 sec (2 sec in the case of right before replacement of the Toner Container) has passed after the Bottle Motor (YM) was turned ON. |
| Remedy: | [Related parts] • Toner Container (Y) • Harness between the DC Controller PCB (UN04/J155) and the Bottle Motor (YM) (M09/J6301) (Unit of replacement: CABLE, MAIN) • Harnesses from the DC Controller PCB to the Bottle Rotation Sensor (Y) 1. DC Controller PCB (UN04/J151) to Relay Connector (3P) (Unit of replacement: CABLE, MAIN) 2. Relay Connector (3P) to Bottle Rotation Sensor (Y) (PS06/J5301) (Unit of replacement: CABLE, BOTTLE SENSOR, Y/C) • Bottle Rotation Sensor (Y) (PS06) (Unit of replacement: PHOTO INTERRUPTER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Bottle Drive Unit (YM) (Unit of replacement: BOTTLE DRIVE ASSEMBLY) • Hopper Unit (Y) (Unit of replacement: HOPPER ASSEMBLY) [Points to note at work] • Be sure to turn over the Door Lock Lever when removing the Bottle Drive Unit (YM) and rotating the drive section by hand. • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E025 0120 |
| Description: | Bottle Motor error (Y). Rotation of bottle was detected while the Toner Bottle Motor (Y) was OFF. |
| Remedy: | [Related parts] • Harnesses from the Bottle Motor (YM) to the DC Controller PCB 1. Bottle Motor (YM) (M04) to Relay Connector (2P) (Unit of replacement: CABLE, BOTTLE DRIVE MOTOR) 2. Relay Connector (2P) to DC Controller PCB (UN04/J127) (Unit of replacement: CABLE, TONER BOTTLE) • Harness between the Toner Supply Sensor (Y) (PS26/J1059) and DC Controller PCB (UN04/J127) (Unit of replacement: CABLE, TONER BOTTLE) • Toner Supply Sensor (Y) • Bottle Drive Unit (YM) (Unit of replacement: BOTTLE DRIVE ASSEMBLY, Y, M) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025 0168 |
| Description: | No toner detection error (Y) |
| Causes: | The state without toner was detected although the recovery sequence was performed for 5 times after replacement of the Toner Container (Y). |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Hopper Unit (Y) (Unit of replacement: HOPPER ASSEMBLY) • Toner Bottle Mount Unit (Y) (Unit of replacement: BOTTLE MOUNT ASSEMBLY) • Drum Unit (Y) (Unit of replacement: DEVE_UNIT_Y) • Toner Container (Y) [Remedy] Check/replace the related parts. [Reference] If a user inserts an empty Toner Container (Y) repeatedly, the error may occur. |
| Error code: | E025 0210 |
| Description: | Bottle Motor (YM) error (M) |
| Causes: | The Bottle Rotation Sensor (M) did not detect rotation for 5 times in a row although 1.5 sec (2 sec in the case of right before replacement of the Toner Container) has passed after the Bottle Motor (YM) was turned ON. |
| Remedy: | [Related parts] • Toner Container (M) • Harness between the DC Controller PCB (UN04/J155) and the Bottle Motor (YM) (M09/J6301) (Unit of replacement: CABLE, MAIN) • Harnesses from the DC Controller PCB to the Bottle Rotation Sensor (M) 1. DC Controller PCB (UN04/J151) to Relay Connector (3P) (Unit of replacement: CABLE, MAIN) 2. Relay Connector (3P) to Bottle Rotation Sensor (M) (PS07/J5302) (Unit of replacement: CABLE, BOTTLE SENSOR, M/K) • Bottle Rotation Sensor (M) (PS07) (Unit of replacement: PHOTO INTERRUPTER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Bottle Drive Unit (YM) (Unit of replacement: BOTTLE DRIVE ASSEMBLY) • Hopper Unit (M) (Unit of replacement: HOPPER ASSEMBLY) [Points to note at work] • Be sure to turn over the Door Lock Lever when removing the Bottle Drive Unit (YM) and rotating the drive section by hand. • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E025 0220 |
| Description: | Bottle Motor error (M). Rotation of bottle was detected while the Toner Bottle Motor (M) was OFF. |
| Remedy: | [Related parts] • Harnesses from the Bottle Motor (YM) to the DC Controller PCB 1. Bottle Motor (YM) (M04) to Relay Connector (2P) (Unit of replacement: CABLE, BOTTLE DRIVE MOTOR) 2. Relay Connector (2P) to DC Controller PCB (UN04/J127) (Unit of replacement: CABLE, TONER BOTTLE) • Harness between the Toner Supply Sensor (M) (PS27/J1060) and DC Controller PCB (UN04/J127) (Unit of replacement: CABLE, TONER BOTTLE) • Toner Supply Sensor (M) • Bottle Drive Unit (YM) (Unit of replacement: BOTTLE DRIVE ASSEMBLY, Y, M) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025 0268 |
| Description: | No toner detection error (M) |
| Causes: | The state without toner was detected although the recovery sequence was performed for 5 times after replacement of the Toner Container (M). |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Hopper Unit (M) (Unit of replacement: HOPPER ASSEMBLY) • Toner Bottle Mount Unit (M) (Unit of replacement: BOTTLE MOUNT ASSEMBLY) • Drum Unit (M) (Unit of replacement: DEVE_UNIT_M) • Toner Container (M) [Remedy] Check/replace the related parts. [Reference] If a user inserts an empty Toner Container (M) repeatedly, the error may occur. |
| Error code: | E025 0310 |
| Description: | Bottle Motor (CK) error (C) |
| Causes: | The Bottle Rotation Sensor (C) did not detect rotation for 5 times in a row although 1.5 sec (2 sec in the case of right before replacement of the Toner Container) has passed after the Bottle Motor (CK) was turned ON. |
| Remedy: | [Related parts] • Toner Container (C) • Harness between the DC Controller PCB (UN04/J155) and the Bottle Motor (CK) (M10/J6302) (Unit of replacement: CABLE, MAIN) • Harnesses from the DC Controller PCB to the Bottle Rotation Sensor (C) 1. DC Controller PCB (UN04/J151) to Relay Connector (3P) (Unit of replacement: CABLE, MAIN) 2. Relay Connector (3P) to Bottle Rotation Sensor (C) (PS08/J5303) (Unit of replacement: CABLE, BOTTLE SENSOR, Y/C) • Bottle Rotation Sensor (C) (PS08) (Unit of replacement: PHOTO INTERRUPTER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Bottle Drive Unit (CK) (Unit of replacement: BOTTLE DRIVE ASSEMBLY) • Hopper Unit (C) (Unit of replacement: HOPPER ASSEMBLY) [Points to note at work] • Be sure to turn over the Door Lock Lever when removing the Bottle Drive Unit (CK) and rotating the drive section by hand. • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E025 0320 |
| Description: | Bottle Motor error (C). Rotation of bottle was detected while the Toner Bottle Motor (C) was OFF |
| Remedy: | [Related parts] • Harnesses from the Bottle Motor (CK) to the DC Controller PCB 1. Bottle Motor (CK) (M05) to Relay Connector (2P) (Unit of replacement: CABLE, BOTTLE DRIVE MOTOR) 2. Relay Connector (2P) to DC Controller PCB (UN04/J127) (Unit of replacement: CABLE, TONER BOTTLE) -Harness between the Toner Supply Sensor (C) (PS28/J1061) and the DC Controller PCB (UN04/J127) (Unit of replacement: CABLE, TONER BOTTLE) • Toner Supply Sensor (C) • Bottle Drive Unit (CK) (Unit of replacement: BOTTLE DRIVE ASSEMBLY, C, K) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025 0368 |
| Description: | No toner detection error (C) |
| Causes: | The state without toner was detected although the recovery sequence was performed for 5 times after replacement of the Toner Container (C). |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Hopper Unit (C) (Unit of replacement: HOPPER ASSEMBLY) • Toner Bottle Mount Unit (C) (Unit of replacement: BOTTLE MOUNT ASSEMBLY) • Drum Unit (C) (Unit of replacement: DEVE_UNIT_C) • Toner Container (C) [Remedy] Check/replace the related parts. [Reference] If a user inserts an empty Toner Container (C) repeatedly, the error may occur. |
| Error code: | E025 0410 |
| Description: | Bottle Motor (CK) error (Bk) |
| Causes: | The Bottle Rotation Sensor (Bk) did not detect rotation for 5 times in a row although 1.5 sec (2 sec in the case of right before replacement of the Toner Container) has passed after the Bottle Motor (CK) was turned ON. |
| Remedy: | [Related parts] • Toner Container (Bk) • Harness between the DC Controller PCB (UN04/J155) and the Bottle Motor (CK) (M10/J6302) (Unit of replacement: CABLE, MAIN) • Harnesses from the DC Controller PCB to the Bottle Rotation Sensor (Bk) 1. DC Controller PCB (UN04/J151) to Relay Connector (3P) (Unit of replacement: CABLE, MAIN) 2. Relay Connector (3P) to Bottle Rotation Sensor (Bk) (PS09/J5304) (Unit of replacement: CABLE, BOTTLE SENSOR, M/K) • Bottle Rotation Sensor (Bk) (PS09) (Unit of replacement: PHOTO INTERRUPTER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Bottle Drive Unit (CK) (Unit of replacement: BOTTLE DRIVE ASSEMBLY) • Hopper Unit (Bk) (Unit of replacement: HOPPER ASSEMBLY) [Points to note at work] • Be sure to turn over the Door Lock Lever when removing the Bottle Drive Unit (CK) and rotating the drive section by hand. • When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E025 0420 |
| Description: | Bottle Motor error (Bk). Rotation of bottle was detected while the Toner Bottle Motor (Bk) was OFF. |
| Remedy: | [Related parts] • Harnesses from the Bottle Motor (CK) to the DC Controller PCB 1. Bottle Motor (CK) (M05) to Relay Connector (2P) (Unit of replacement: CABLE, BOTTLE DRIVE MOTOR) 2. Relay Connector (2P) to DC Controller PCB (UN04/J127) (Unit of replacement: CABLE, TONER BOTTLE) • Harness between the Toner Supply Sensor (Bk) (PS29/J1062) and the DC Controller PCB (UN04/J127) (Unit of replacement: CABLE, TONER BOTTLE) • Toner Supply Sensor (Bk) • Bottle Drive Unit (CK) (Unit of replacement: BOTTLE DRIVE ASSEMBLY, C, K) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025 0468 |
| Description: | No toner detection error (Bk) |
| Causes: | The state without toner was detected although the recovery sequence was performed for 5 times after replacement of the Toner Container (Bk). |
| Remedy: | [Related parts] • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • Hopper Unit (Bk) (Unit of replacement: HOPPER ASSEMBLY) • Toner Bottle Mount Unit (Bk) (Unit of replacement: BOTTLE MOUNT ASSEMBLY) • Drum Unit (Bk) (Unit of replacement: P-UNIT_BK) • Toner Container (Bk) [Remedy] Check/replace the related parts. [Reference] If a user inserts an empty Toner Container (Bk) repeatedly, the error may occur. |
| Error code: | E029 5008 |
| Description: | Registration Patch Sensor (Front) light intensity error |
| Causes: | The background regular reflection output of the Registration Patch Sensor at the front side did not fall within the specified range for 2 consecutive times at initialization. |
| Remedy: | [Related parts] • Registration Patch Sensor Unit (Front) (UN31) (Unit of replacement: REGISTRATION SENSOR ASSEMBLY) • Registration Patch Sensor Unit (Front) Shutter (Unit of replacement: SHUTTER, REGISTRATION SENSOR) • Registration Shutter Solenoid (SL03) (Unit of replacement: SOLENOID) • Harness between the Registration Patch Sensor Unit (Front) and the DC Controller PCB 1. Registration Patch Sensor Unit (Front) (UN31/J5603) to Relay Connector (16P) (Unit of replacement: CABLE, REG. DETECT) 2. Relay Connector (16P) to Relay Connector (16P) (Unit of replacement: CABLE CONNECTING ASSEMBLY) 3. Relay Connector (16P) to DC Controller PCB (UN04/J170) (Unit of replacement: 2ST TRANS. H.V. CONTACT ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Perform the following in the order while checking whether the error is cleared. Check the background regular reflection output value (front) in COPIER > DISPLAY> DENS> P-B-P-C. a. If the value is less than 10, 1. Check if the sensor window of the Registration Patch Sensor Unit (Front) is soiled. If it is soiled, clean it with a blower. 2. Check that the Registration Patch Sensor Unit (Front) Shutter is properly installed and it is not damaged or deformed. If it is deformed or damaged, replace the Registration Patch Sensor Unit (Front). 3. Check the operation of the Registration Shutter Solenoid. 3-1. If the Registration Shutter Solenoid moves, 3-1-1. Replace the Registration Patch Sensor Unit (Front). 3-1-2. Replace the DC Controller PCB. 3-2. If the solenoid does not move, replace the Registration Shutter Solenoid. b. If the value is above 250, 1. Check the harness between the Registration Patch Sensor Unit (Front) and the DC Controller PCB. 2. Replace the harness between the Registration Patch Sensor Unit (Front) and the DC Controller PCB. 3. Replace the Registration Patch Sensor Unit (Front). 4. Replace the DC Controller PCB. |
| Error code: | E029 7008 |
| Description: | Registration Patch Sensor (Rear) light intensity error |
| Causes: | The background regular reflection output of the Registration Patch Sensor at the rear side did not fall within the specified range for 2 consecutive times at initialization. |
| Remedy: | [Related parts] • Registration Patch Sensor Unit (Rear) (UN32) (Unit of replacement: REGISTRATION SENSOR ASSEMBLY) • Registration Patch Sensor Unit (Rear) Shutter (Unit of replacement: SHUTTER, REGISTRATION SENSOR) • Registration Shutter Solenoid (SL03) (Unit of replacement: SOLENOID) • Harness between the Registration Patch Sensor Unit (Rear) and the DC Controller PCB 1. Registration Patch Sensor Unit (Rear) (UN32/J5604) to Relay Connector (16P) (Unit of replacement: CABLE, REG. DETECT) 2. Relay Connector (16P) to Relay Connector (16P) (Unit of replacement: CABLE CONNECTING ASSEMBLY) 3. Relay Connector (16P) to DC Controller PCB (UN04/J170) (Unit of replacement: 2ST TRANS. H.V. CONTACT ASS’Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Perform the following in the order while checking whether the error is cleared. Check the background regular reflection output value (rear) in COPIER > DISPLAY> DENS> P-B-P-Y. a. If the value is less than 10, 1. Check if the sensor window of the Registration Patch Sensor Unit (Rear) is soiled. If it is soiled, clean it with a blower. 2. Check that the Registration Patch Sensor Unit (Rear) Shutter is properly installed and it is not damaged or deformed. If it is deformed or damaged, replace the Registration Patch Sensor Unit (Rear). 3. Check the operation of the Registration Shutter Solenoid. 3-1. If the Registration Shutter Solenoid moves, 3-1-1. Replace the Registration Patch Sensor Unit (Rear). 3-1-2. Replace the DC Controller PCB. 3-2. If the solenoid does not move, replace the Registration Shutter Solenoid. b. If the value is above 250, 1. Check the harness between the Registration Patch Sensor Unit (Rear) and the DC Controller PCB. 2. Replace the harness between the Registration Patch Sensor Unit (Rear) and the DC Controller PCB. 3. Replace the Registration Patch Sensor Unit (Rear). 4. Replace the DC Controller PCB. |
| Error code: | E073 0001 |
| Description: | Interlock error |
| Causes: | No detection of Interlock (24 V) although all the Doors (Front Cover and Right Cover) of the host machine were closed. |
| Remedy: | [Related parts] • Front Cover/Right Cover • Harness between the Interlock Switch 1 and 2 (SW02 and SW03) and the DC Controller PCB (UN04/J24/pin 1 and 2) (Unit of replacement: COVER, INNER, FRONT, RIGHT) • Harness between the Low-voltage Power Supply PCB (UN01/J315) and the DC Controller PCB (UN04/J20) (Unit of replacement: CABLE, POWER SUPPLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Front Cover/Right Cover is closed. 2. Visually check that the Interlock Switch 1 and 2 are turned ON/OFF by opening/closing the Front Cover/Right Cover. 3. Check that the harness between the Interlock Switch 1 and 2 and the DC Controller PCB is not short-circuited (the harness does not come in contact with the plate while the cable sheath is peeled). 4. Disconnect the connector (J24) of the DC Controller while the Front Cover and the Right Cover are closed, and measure the resistance value between the connectors J24/1-pin and the J24/2-pin on the J24 harness side using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the DC Controller PCB. 2. Replace the Low-voltage Power Supply PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the harness between the Interlock Switch 1 and 2 and the DC Controller PCB. 5. Check the harness between the Low-voltage Power Supply PCB and the DC Controller PCB. 6. Replace the DC Controller PCB. 7. Replace the Low-voltage Power Supply PCB. |
| Error code: | E074 0001 |
| Description: | ITB HP time out error. The HP Sensor in the Main Drive Unit did not detect home position within the specified period of time. |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Primary Transfer Roller Disengagement HP Sensor 1. DC Controller PCB (UN04/J131) to Relay Connector (3P) (Unit of replacement: CABLE, MAIN DRIVE) 2. Relay Connector (3P) to Primary Transfer Roller Disengagement HP Sensor (PS33/J1189) (Unit of replacement: CABLE, SENSOR) • Harness between the DC Controller PCB (UN04/J131) and the Primary Transfer Roller Disengagement Motor (M08/J1201) (Unit of replacement: CABLE, MAIN DRIVE) • Harness between the DC Controller PCB (UN04/J129) and the Bk Drum_ITB Motor (M02/J1054) (Unit of replacement: CABLE, MAIN DRIVE) • Primary Transfer Roller Disengagement HP Sensor (PS33) • Primary Transfer Roller Disengagement Motor (M08) • Bk Drum_ITB Motor (M02) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • ITB Unit (Unit of replacement: INTER. TRANSFER BELT ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E074 0002 |
| Description: | Error in Primary Transfer Roller operation |
| Causes: | The ITB Pressure Release Switch could not detect the engagement operation within the specified period of time at engagement operation of the Primary Transfer Roller. |
| Remedy: | [Related parts] • ITB Unit (Unit of replacement: INTER. TRANSFER BELT ASS`Y) • Harnesses from the DC Controller PCB to the ITB Pressure Release Switch 1. DC Controller PCB (UN04/J162) to Relay Connector (2P) (Unit of replacement: PROCESS CONTROL PCB ASS`Y) 2. Relay Connector (2P) to ITB Pressure (Unit of replacement: 1ST TRANS. H.V. CONTACT ASS`Y) • Release Switch (SW07/J6005) • Harness between the DC Controller PCB (UN04/J140) and the Primary Transfer Separation Solenoid (SL01/J5708) (Unit of replacement: MAIN DRIVE ASSEMBLY) • Fuse in the DC Controller PCB (UN04/FU07) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • ITB Guide Rail (Unit of replacement: RAIL, I.T.B., FRONT/RAIL, I.T.B., REAR) • Main Drive Unit (Unit of replacement: MAIN DRIVE ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable.. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the ITB Unit is installed in the machine. 2. Replace the ITB Unit. 3. Check the harness between the DC Controller PCB and the ITB Pressure Release Switch. 4. Check the harness between the DC Controller PCB and the Primary Transfer Separation Solenoid. 5. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the ITB Guide Rail (Front/Rear). 2. Replace the Main Drive Unit. 3. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Caution] After replacing the DC Controller PCB, measure the resistance value between the Low-voltage Power Supply PCB (UN01/J315/4-pin) and the DC Controller PCB (UN04/J20/1-pin) using a tester before turning ON the main power to prevent blowout of a fuse again. If the measurement value is 1 ohm or higher (non conduction state), perform the following in the order while checking whether the error is cleared. 1. Replace the harness between the DC Controller PCB and the ITB Pressure Release Switch. 2. Replace the harness between the DC Controller PCB and the Primary Transfer Separation Solenoid. |
| Error code: | E100 0001 |
| Description: | Error in scanner motor/laser unit/BD |
| Causes: | Failure in Magenta optical unit |
| Remedy: | 1.Check connectors of laser scanner unit and DC controller PCB 2.Replace laser scanner units 3.Replace DC controller PCBs |
| Error code: | E110 0001 |
| Description: | Scanner Motor error |
| Causes: | The speed was not locked by FG control within 5.5 sec after startup of Scanner Motor. |
| Remedy: | [Related parts] • Front Cover/Right Cover • Interlock Switch 1 and 2 (SW02 and SW03/J24/1-pin and 2-pin) (Unit of replacement: COVER, INNER, FRONT, RIGHT) • Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/ Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER SCANNER) • Flexible Cable between the Main Controller PCB (UN81/J7002) and the Y/ M/C/Bk Laser Driver PCB (UN05/J201) (Unit of replacement: CABLE, FLAT) • Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER SCANNER ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E110 0002 |
| Description: | Scanner Motor error |
| Causes: | The speed was not locked by BD control within 5.5 sec after startup of Scanner Motor. |
| Remedy: | [Related parts] • Front Cover/Right Cover • Interlock Switch 1 and 2 (SW02 and SW03/J24/1-pin and 2-pin) (Unit of replacement: COVER, INNER, FRONT, RIGHT) • Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/ Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER SCANNER) • Flexible Cable between the Main Controller PCB (UN81/J7002) and the Y/ M/C/Bk Laser Driver PCB (UN05/J201) (Unit of replacement: CABLE, FLAT) • Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER SCANNER ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E110 0003 |
| Description: | Scanner Motor error |
| Causes: | The phase was not locked by BD control within 5.5 sec after startup of Scanner Motor. |
| Remedy: | [Related parts] • Front Cover/Right Cover • Interlock Switch 1 and 2 (SW02 and SW03/J24/1-pin and 2-pin) (Unit of replacement: COVER, INNER, FRONT, RIGHT) • Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/ Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER SCANNER) • Flexible Cable between the Main Controller PCB (UN81/J7002) and the Y/ M/C/Bk Laser Driver PCB (UN05/J201) (Unit of replacement: CABLE, FLAT) • Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER SCANNER ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E110 0004 |
| Description: | Scanner Motor error. Correction in timing of laser exposure to the Polygon Mirror was not detected after the phase lock by BD control. |
| Remedy: | [Related parts] • Flat Cable between the Y/M Laser Driver PC (UN08/J203) and the C/Bk Laser Driver PCB (UN09/J801) (Unit of replacement: CABLE, FLAT) • Flat Cable between the Main Controller PCB (UN05/J19) and the Y/M Laser Driver PCB (UN08/J201) (Unit of replacement: FLEXIBLE FLAT CABLE ASSEMBLY) • Harness between the DC Controller PCB (UN04/J111) and the Y/M Laser Driver PCB (UN08/J202) (Unit of replacement: CABLE, CASSETTE SIZE) • Y/M Laser Driver PCB (UN08) (Unit of replacement: LASER SCANNER ASSEMBLY) • C/Bk Laser Driver PCB (UN09) (Unit of replacement: LASER SCANNER ASSEMBLY) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After replacement of the Laser Driver PCB, execute "Settings/ Registration> Adjustment/Maintenance> Adjust Image Quality> Auto Correct Color Mismatch". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E193 0001 |
| Description: | Image ASIC communication error |
| Causes: | Communication between the DC Controller PCB (CPU) and IMG1L (ASIC) in the Main Controller PCB was not available. |
| Remedy: | [Related parts] • Front Cover/Right Cover • Interlock Switch 1 and 2 (SW02 and SW03/J24/1-pin and 2-pin) (Unit of replacement: COVER, INNER, FRONT, RIGHT) • Flexible Cable between the DC Controller PCB (UN04/J112) and the Main Controller PCB (UN81/J7001) (Unit of replacement: CABLE, FLAT) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E196 0000 |
| Description: | DCON error |
| Causes: | Failed to update ROM of DC controller PCB |
| Remedy: | 1) Replace the Engine Controller PCB. |
| Error code: | E196 0001 |
| Description: | Error of access data in the EEPROM |
| Causes: | Fail to access EEPROM data. |
| Remedy: | Replace the engine controller PCB (PCB1). |
| Error code: | E196 000F |
| Description: | EEPROM communication error |
| Causes: | The number of read/write job data to the DCON EEPROM (device information) exceeded 100. |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E196 0100 |
| Description: | EEPROM communication error |
| Causes: | The NACK (a negative reply sent by the reception side to the sending side) was received for 3 times in communication from the DC Controller PCB (CPU) to the SCNR EEPROM. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER SCANNER) • Harness between the DC Controller PCB (UN04/J184) and the Developing High-voltage PCB (UN06/J241) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASSEMBLY) • Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER SCANNER ASSEMBLY) • Developing High-voltage PCB (UN06) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E196 0101 |
| Description: | EEPROM communication error |
| Causes: | Although access to the SCNR EEPROM from the DC Controller PCB (CPU) was executed for 3 times, no response was received and timeout occurred. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/ Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER SCANNER) • Harness between the DC Controller PCB (UN04/J184) and the Developing High-voltage PCB (UN06/J241) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASSEMBLY) • Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER SCANNER ASSEMBLY) • Developing High-voltage PCB (UN06) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E196 010F |
| Description: | EEPROM communication error |
| Causes: | The number of read/write job data to the SCNR EEPROM (device information) exceeded 100. |
| Remedy: | Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E196 0800 |
| Description: | EEPROM communication error |
| Causes: | The NACK (a negative reply sent by the reception side to the sending side) was received for 3 times in communication from the DC Controller PCB (CPU) to the HVT EEPROM. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER SCANNER) • Harness between the DC Controller PCB (UN04/J184) and the Developing High-voltage PCB (UN06/J241) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASSEMBLY) • Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER SCANNER ASSEMBLY) • Developing High-voltage PCB (UN06) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E196 0801 |
| Description: | EEPROM communication error |
| Causes: | Although access to the HVT EEPROM from the DC Controller PCB (CPU) was executed for 3 times, no response was received and timeout occurred. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) (Unit of replacement: CABLE, LASER SCANNER) • Harness between the DC Controller PCB (UN04/J184) and the Developing High-voltage PCB (UN06/J241) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASSEMBLY) • Y/M/C/Bk Laser Driver PCB (UN05) (Unit of replacement: LASER SCANNER ASSEMBLY) • Developing High-voltage PCB (UN06) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E196 080F |
| Description: | EEPROM communication error |
| Causes: | The number of read/write job data to the HVT EEPROM (device information) exceeded 100. |
| Remedy: | Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E197 0B11 |
| Description: | Serial communication error.Communication between the DC Controller PCB and the Second/ Third Delivery PCB was not completed. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J123) and the Second/Third Delivery Unit (J701) (Unit of replacement: CABLE, FEED) • Second/Third Delivery Unit (Unit of replacement: 2ND/3RD DELIVERY DRIVE ASS`Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197 0B20 |
| Description: | Serial communication error. A communication error of ASIC in the DC Controller PCB was detected |
| Remedy: | [Remedy] Replace the DC Controller PCB (UN04). (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197 0B21 |
| Description: | Serial communication error. A communication error between the DC Controller PCB and the Cassette Unit PCB was detected. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J126) and the Cassette Unit PCB (Unit of replacement: CABLE, FEED MOTOR) • Cassette Unit PCB (Unit of replacement: CASSETTE ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197 1001 |
| Description: | Serial communication error. A communication error between the CPU of the DC Controller PCB and KONA1 (ASIC) in the DC Controller PCB was detected. |
| Remedy: | [Remedy] Replace the DC Controller PCB (UN04). (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197 1002 |
| Description: | Serial communication error. A communication error between the CPU of the DC Controller PCB and KONA2 (ASIC) in the DC Controller PCB was detected. |
| Remedy: | [Remedy] Replace the DC Controller PCB (UN04). (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197 1004 |
| Description: | Serial communication error. Communication between the DC Controller PCB and the Laser Driver PCB was not completed. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J111) and the Y/M Laser Driver PCB (UN08/J202) (Unit of replacement: CABLE, CASSETTE SIZE) • Flat Cable between the Y/M Laser Driver PCB (UN08/ J203) and the C/Bk Laser Driver PCB (UN09/J801) (Unit of replacement: CABLE, FLAT) • Y/M Laser Driver PCB (UN08) (Unit of replacement: LASER SCANNER ASSEMBLY) • C/Bk Laser Driver PCB (UN09) (Unit of replacement: LASER SCANNER ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After replacement of the Laser Driver PCB, execute "Settings/ Registration> Adjustment/Maintenance> Adjust Image Quality> Auto Correct Color Mismatch". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197 1081 |
| Description: | Serial communication error. A communication error between the CPU of the DC Controller PCB and KONA1 (ASIC) in the DC Controller PCB was detected. (An error caused by software) |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power |
| Error code: | E197 1082 |
| Description: | Serial communication error.A communication error between the CPU of the DC Controller PCB and KONA2 (ASIC) in the DC Controller PCB was detected. (An error caused by software) |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power |
| Error code: | E197 1084 |
| Description: | Serial communication error. A communication error between the DC Controller PCB and the Laser Driver PCB was detected. (An error caused by software) |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E197 5000 |
| Description: | Serial communication error. A communication error between the DC Controller PCB and the Secondary Transfer High Voltage PCB was detected at power-on. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J112 and J114) and the Secondary Transfer High Voltage PCB (UN03/ J502 and J501) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB) • Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRANSFER H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197 5001 |
| Description: | Serial communication error. A communication error between the DC Controller PCB and the Primary Transfer High Voltage PCB was detected at power-on. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J113) and the Primary Transfer High Voltage PCB (UN02/J401) (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) • Primary Transfer High Voltage PCB (UN02) (Unit of replacement: 1ST TRNSFR. H.V. PCB ASS`Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E202 0001 |
| Description: | CIS Unit HP error (outward) |
| Causes: | CIS Unit did not move to HP even it moved backward. Reader HP Sensor error, Reader Motor error, CIS Unit error |
| Remedy: | 1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit. |
| Error code: | E202 0002 |
| Description: | CIS Unit HP error (homeward) |
| Causes: | CIS Unit did not move to HP even it moved forward. Reader HP Sensor error, Reader Motor error, CIS Unit error |
| Remedy: | 1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit. |
| Error code: | E202 0003 |
| Description: | Scanner HP error. An error in the Scanner Unit (Paper Front) position was detected when reading of a job was started. |
| Remedy: | [Related parts] • Harness between the Scanner Motor (M1/J5015) and the Main Controller PCB (UN05/J36) (Unit of replacement: CABLE, MOTOR) • Harness between the Scanner Unit HP Sensor (PS2/J5009) and the Main Controller PCB (UN05/J37) (Unit of replacement: CABLE, SENSOR) • Scanner Unit HP Sensor (PS2) • Scanner Motor (M1) (Unit of replacement: MOTOR ASS`Y) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E227 0001 |
| Description: | Power supply (24 V) error. The Main Controller PCB did not detect 24 V at power-on. |
| Remedy: | [Related parts] • Harnesses from the Main Controller PCB to the ADF Driver PCB 1. Main Controller PCB (UN05/J38) to Relay Connector (2P) (Unit of replacement: CABLE, ADF POWER CONNECTING) 2. Relay Connector (2P) to ADF Driver PCB (PCB1/J1411) • Harness between the Main Controller PCB (UN05/J20) and the Low Voltage Power Supply PCB (UN01/J313) (Unit of replacement: POWER SUPPLY ASSEMBLY) • ADF Driver PCB (PCB1) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Remedy] Perform the following in the order while checking whether the error is cleared. • When an error is detected, conduction of 24 V is stopped. At power check, check if 24 V is conducted by repeating power cycling of the machine. 1. Measure the Low Voltage Power Supply PCB (J313/pin 3) using a tester. 2. When 24 V is not output to the Low Voltage Power Supply PCB (J313/pin 3), replace the Low Voltage Power Supply PCB. 3. When 24 V is output to the Low Voltage Power Supply PCB (J313/pin 3), measure the Main Controller PCB (J20/pin 3) using a tester. 4. When 24 V is not output to the Main Controller PCB (J20/pin 3), check the harness between the Main Controller PCB and the Low Voltage Power Supply PCB. 5. When 24 V is output to the Main Controller PCB (J20/pin 3), measure the Main Controller PCB (J38/pin 2) using a tester. 6. When 24 V is not output to the Main Controller PCB (J38/pin 2), replace the Main Controller PCB. 7. When 24 V is output to the Main Controller PCB (J38/pin 2), measure the ADF Driver PCB (J1411/pin 2) using a tester. 8. When 24 V is not output to the ADF Driver PCB (J1411/pin 2), check the harnesses from the Main Controller PCB to the ADF Driver PCB. 9. When 24 V is output to the ADF Driver PCB (J1411/pin 2), replace the ADF Driver PCB. |
| Error code: | E227 0101 |
| Description: | Power supply (24 V) error. The ADF Driver PCB did not detect 24 V after the start of a job. |
| Remedy: | [Related parts] • Harnesses from the Main Controller PCB to the ADF Driver PCB 1. Main Controller PCB (UN05/J38) to Relay Connector (2P) (Unit of replacement: CABLE, ADF POWER CONNECTING) 2. Relay Connector (2P) to ADF Driver PCB (PCB1/J1411) • Harness between the Main Controller PCB (UN05/J20) and the Low Voltage Power Supply PCB (UN01/J313) (Unit of replacement: POWER SUPPLY ASSEMBLY) • ADF Driver PCB (PCB1) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Remedy] Perform the following in the order while checking whether the error is cleared. • When an error is detected, conduction of 24 V is stopped. At power check, check if 24 V is conducted by repeating power cycling of the machine. 1. Measure the Low Voltage Power Supply PCB (J313/pin 3) using a tester. 2. When 24 V is not output to the Low Voltage Power Supply PCB (J313/pin 3), replace the Low Voltage Power Supply PCB. 3. When 24 V is output to the Low Voltage Power Supply PCB (J313/pin 3), measure the Main Controller PCB (J20/pin 3) using a tester. 4. When 24 V is not output to the Main Controller PCB (J20/pin 3), check the harness between the Main Controller PCB and the Low Voltage Power Supply PCB. 5. When 24 V is output to the Main Controller PCB (J20/pin 3), measure the Main Controller PCB (J38/pin 2) using a tester. 6. When 24 V is not output to the Main Controller PCB (J38/pin 2), replace the Main Controller PCB. 7. When 24 V is output to the Main Controller PCB (J38/pin 2), measure the ADF Driver PCB (J1411/pin 2) using a tester. 8. When 24 V is not output to the ADF Driver PCB (J1411/pin 2), check the harnesses from the Main Controller PCB to the ADF Driver PCB. 9. When 24 V is output to the ADF Driver PCB (J1411/pin 2), replace the ADF Driver PCB |
| Error code: | E240 0000 |
| Description: | Controller communication error |
| Causes: | sequence error with the controller occurred. |
| Remedy: | [Related parts] • Flexible Cable between the DC Controller PCB (UN04/J112) and the Main Controller PCB (UN81/J7001) (Unit of replacement: CABLE, FLAT) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the harness between the DC Controller PCB and the Main Controller PCB. 2. Turn ON the power, and check if the initialization is executed at startup. 2-1. If the initialization is not executed, replace the DC Controller PCB. 2-2. If the initialization is executed, replace the Main Controller PCB. |
| Error code: | E246 0001 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E246 0002 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E246 0003 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E246 0005 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E247 0001 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E247 0002 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the service company office |
| Error code: | E247 0003 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact the service company office |
| Error code: | E248 0001 |
| Description: | Error in access to backup data for Reader (reading error at power-on) |
| Causes: | The Reader-related adjustment values could not be read. |
| Remedy: | 1. Clear the backup RAM of RCON. Execute COPIER>FUNCTION>CLEAR>RCON. 2. Enter all the values written on the service label in service mode again. 3. Turn OFF and then ON the main power. 4. Replace the Main Controller PCB. |
| Error code: | E260 0001 |
| Description: | Power supply error. Short-circuit was detected at power-on. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J100 and J115) and the Low Voltage Power Supply PCB (UN01/J315 and J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E260 0002 |
| Description: | Power supply error. Open circuit was detected at power-on. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J100 and J115) and the Low Voltage Power Supply PCB (UN01/J315 and J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E270 0001 |
| Description: | Scanner Unit communication error. The vertical scanning synchronous signal (VSYNC) was not transmitted normally at the Scanner Unit side that communicates with the Main Controller PCB. |
| Remedy: | [Related parts] • Flat Cable between the Main Controller PCB (UN05/J33) and the Scanner Unit (Unit of replacement: CABLE, FLAT) • Scanner Unit (Unit of replacement: SCANNER UNIT) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E270 0002 |
| Description: | Scanner Unit communication error. The vertical scanning synchronous signal (VSYNC) was not transmitted due to horizontal scanning synchronous signal (HSYNC) error which is sent to the Main Controller PCB. |
| Remedy: | [Related parts] • Flat Cable between the Main Controller PCB (UN05/J33) and the Scanner Unit (Unit of replacement: CABLE, FLAT) • Scanner Unit (Unit of replacement: SCANNER UNIT) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E280 0001 |
| Description: | Scanner Unit communication error. Communication between the Main Controller and the Scanner Unit was not started within the specified period of time. |
| Remedy: | [Related parts] • Flat Cable between the Main Controller PCB (UN05/J33) and the Scanner Unit (Unit of replacement: CABLE, FLAT) • Scanner Unit (Unit of replacement: SCANNER UNIT) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E280 0002 |
| Description: | Scanner Unit communication error. Disconnection of FFC between the Main Controller and the Scanner Unit was detected. |
| Remedy: | [Related parts] • Flat Cable between the Main Controller PCB (UN05/J33) and the Scanner Unit (Unit of replacement: CABLE, FLAT) • Scanner Unit (Unit of replacement: SCANNER UNIT) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E280 0003 |
| Description: | Scanner Unit communication error. Reading or writing error was detected between the Main Controller and the Scanner Unit. |
| Remedy: | [Related parts] • Flat Cable between the Main Controller PCB (UN05/J33) and the Scanner Unit (Unit of replacement: CABLE, FLAT) • Scanner Unit (Unit of replacement: SCANNER UNIT) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E280 0004 |
| Description: | Scanner Unit communication error |
| Causes: | 1. The CIS was not connected. 2. A CIS other than that for this machine was connected. |
| Remedy: | [Related parts] • Flexible Cable between the Scanner Unit (CIS01, CIS02/J911) and the Main Controller PCB (UN81/J8101) (Unit of replacement: CABLE, FLAT) • Scanner Unit (CIS01/CIS02) (Unit of replacement: CONTACT IMAGE SENSOR ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E302 0001 |
| Description: | Shading error. An error in the shading value was detected at white shading. |
| Remedy: | [Related parts] • Harness between the Scanner Unit and the LED PCB (Unit of replacement: LASER SCANNER ASSEMBLY) • Flat Cable between the Main Controller PCB (UN05/J33) and the Scanner Unit (Unit of replacement: CABLE, FLAT) • Scanner Unit (Unit of replacement: SCANNER UNIT) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • Stream Reading Glass (Unit of replacement: GLASS, READER) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E302 0002 |
| Description: | Shading error. An error in the shading value was detected at black shading. |
| Remedy: | [Related parts] • Harness between the Scanner Unit and the LED PCB (Unit of replacement: LASER SCANNER ASSEMBLY) • Flat Cable between the Main Controller PCB (UN05/J33) and the Scanner Unit (Unit of replacement: CABLE, FLAT) • Scanner Unit (Unit of replacement: SCANNER UNIT) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • Stream Reading Glass (Unit of replacement: GLASS, READER) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E315 0007 |
| Description: | Image processing device error. JBIG encode error was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 000D |
| Description: | Image processing device error. JBIG decode error was detected. |
| Remedy: | [Related parts] • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • HDD (Unit of replacement: HARD DISK DRIVE) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power (so the current job is deleted). 3. After turning OFF the main power, replace the HDD and the Main Controller PCB at the same time. 4. Execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. |
| Error code: | E315 000E |
| Description: | Image processing device error. An error was detected at software decoding. |
| Remedy: | [Related parts] • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • HDD (Unit of replacement: HARD DISK DRIVE) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power (so the current job is deleted). 3. After turning OFF the main power, replace the HDD and the Main Controller PCB at the same time. 4. Execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. |
| Error code: | E315 000F |
| Description: | Image processing device error. MemoryCopy error was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0027 |
| Description: | Image processing device error. ROTU timeout error was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0035 |
| Description: | Image processing device error. MemFill timeout error was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0100 |
| Description: | Image processing device error. PRIO overrun. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0500 |
| Description: | Device timeout error. An image synchronous signal from the Main Controller PCB to the Reader could not be detected for 30 sec or longer. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0501 |
| Description: | Image processing device error. An abnormal signal from the Main Controller PCB to the Reader was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0510 |
| Description: | Device timeout error. An image synchronous signal from the Main Controller PCB to the Reader could not be detected for 30 sec or longer. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0511 |
| Description: | Image processing device error. An abnormal signal from the Main Controller PCB to the Reader was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0520 |
| Description: | Device timeout error. An image synchronous signal from the Main Controller PCB to the Reader could not be detected for 30 sec or longer. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0521 |
| Description: | Image processing device error. An abnormal signal from the Main Controller PCB to the Reader was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0530 |
| Description: | Device timeout error. An image synchronous signal from the Main Controller PCB to the Reader could not be detected for 30 sec or longer. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0531 |
| Description: | Image processing device error. An abnormal signal from the Main Controller PCB to the Reader was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0540 |
| Description: | Device timeout error. An image synchronous signal from the Main Controller PCB to the Reader could not be detected for 30 sec or longer. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0541 |
| Description: | Image processing device error. An abnormal signal from the Main Controller PCB to the Reader was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0550 |
| Description: | Device timeout error. An image synchronous signal from the Main Controller PCB to the Reader could not be detected for 30 sec or longer. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E315 0551 |
| Description: | Image processing device error. An abnormal signal from the Main Controller PCB to the Reader was detected. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E350 0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E350 0001 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E350 0002 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E350 0003 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E350 3000 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E351 0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E354 0001 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E354 0002 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E355 0001 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E355 0002 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E355 0003 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E355 0004 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E400 0002 |
| Description: | Communication error. A communication error between the Main Controller PCB and the ADF Driver PCB was detected. |
| Remedy: | [Related parts] • Harnesses from the Main Controller PCB to the ADF Driver PCB 1. Main Controller PCB (UN05/J35) to Relay Connector (19P) (Unit of replacement: CABLE, ADF DATA CONNECTING) 2. Relay Connector (19P) to ADF Driver PCB (PCB1/J1410) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) • ADF Driver PCB (PCB1) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E500 0000 |
| Description: | Communication error. A communication error between the host machine and the Finisher was detected. |
| Remedy: | [Related parts] • Harnesses and connectors from the DC Controller PCB to the Finisher Controller PCB • Finisher Controller PCB (PCB1) • DC Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness and connector between the DC Controller PCB and the Finisher Controller PCB. 2. Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. 3. Replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E501 0091 |
| Description: | Communication error. A communication error between the Finisher and the Buffer Pass was detected. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Buffer Pass Controller PCB to the Finisher Controller PCB • Buffer Pass Controller PCB (PCB201) • Finisher Controller PCB (PCB1) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness and connector between the Buffer Pass Controller PCB and the Finisher Controller PCB. 2. Replace the Buffer Pass Controller PCB. 3. Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E503 0002 |
| Description: | Communication error. A communication error between the Finisher Controller PCB and the Saddle Stitcher Controller PCB was detected. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Saddle Stitcher Controller PCB • Finisher Controller PCB (PCB1) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the harness and connector between the Finisher Controller PCB and the Saddle Stitcher Controller PCB. 2. Replace the Finisher Controller PCB. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. 3. Replace the Saddle Stitcher Controller PCB. |
| Error code: | E505 0001 |
| Description: | Error in EEPROM of the Finisher. An error was detected in the check sum value of data read from EEPROM on the Finisher Controller PCB. |
| Remedy: | [Related parts] Finisher Controller PCB (PCB1) [Remedy] Check/replace the Finisher Controller PCB (PCB1). [Reference] Before replacing the Finisher Controller PCB, back up the service mode data and restore the backup data after the replacement so the data may be able to be protected. • Backup: SORTER (LEVEL1)> FUNCTION> SYSTEM> FINBK- R • Restoration: SORTER (LEVEL1)> FUNCTION> SYSTEM> FIN-BK-W |
| Error code: | E505 0004 |
| Description: | Error in CPU of the Buffer Pass. An error was detected in the check sum value of data read from CPU on the Buffer Pass Controller PCB. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] Buffer Pass Controller PCB (PCB201) [Remedy] Check/replace the Buffer Pass Controller PCB (PCB201). |
| Error code: | E514 0002 |
| Description: | Assist Motor error. • The Assist HP Sensor was not turned ON although 3 seconds had passed after the Assist Motor operation started. • The Assist HP Sensor was not turned ON when starting operation. |
| Remedy: | INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Assist HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Assist Motor • Assist HP Sensor (PS7) • Assist Motor (M5) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E514 8001 |
| Description: | a. Assist Motor error b. Rear End Assist Guide HP error. a. The Assist HP Sensor was not turned OFF although 1 second had passed after the Assist Motor operation started. b. The rear end assist guide does not come off the Rear End Assist Guide HP Sensor although the Rear End Assist Guide Motor has been driven for 3 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Assist HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Assist Motor • Assist HP Sensor (PS7) • Assist Motor (M5) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Rear End Assist Guide HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Rear End Assist Guide Motor • Rear end assist guide drive mechanism • Rear End Assist Guide HP Sensor (PI109) • Rear End Assist Guide Motor (M109) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E514 8002 |
| Description: | Rear End Assist Guide HP error. The Rear End Assist Guide HP Sensor does not detect the rear end assist guide although the Rear End Assist Guide Motor has been driven for 3 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Rear End Assist Guide HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Rear End Assist Guide Motor • Rear end assist guide drive mechanism • Rear End Assist Guide HP Sensor (PI109) • Rear End Assist Guide Motor (M109) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E516 0001 |
| Description: | Paddle Motor error. • The Paper Fold HP Sensor was not turned OFF although 3 seconds had passed after the Paddle Motor operation started. • The last paper fold operation is not finished when driving the Paddle Motor. |
| Remedy: | INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Paper Fold HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Paddle Motor • Paper Fold HP Sensor (PS8) • Paddle Motor (M10) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E516 0002 |
| Description: | Paddle Motor error. • The Paper Fold HP Sensor was not turned ON although 3 seconds had passed after the Paddle Motor operation started. • The last paper fold operation is not finished when driving the Paddle Motor. |
| Remedy: | INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Paper Fold HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Paddle Motor • Paper Fold HP Sensor (PS8) • Paddle Motor (M10) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E530 8001 |
| Description: | a. Rear Alignment Motor error b. Front Aligning Plate HP error. a. The Rear Alignment Plate HP Sensor was not turned OFF although 1 second had passed after the Rear Alignment Motor operation started. b. The front aligning plate does not come off the Front Aligning Plate HP Sensor although the Front Aligning Plate Motor has been driven for 4 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Rear Alignment Plate HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Rear Alignment Motor • Rear Alignment Plate HP Sensor (PS5) • Rear Alignment Motor (M4) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Front Aligning Plate HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Front Aligning Plate Motor • Front aligning plate drive mechanism • Front Aligning Plate HP Sensor (PI106) • Front Aligning Plate Motor (M103) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E530 8002 |
| Description: | a. Rear Alignment Motor error b. Front Aligning Plate HP error. a. The Rear Alignment Plate HP Sensor was not turned ON although 5 seconds had passed after the Rear Alignment Motor operation started. b. The Front Aligning Plate HP Sensor does not detect the front aligning plate although the Front Aligning Plate Motor has been driven for 4 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Rear Alignment Plate HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Rear Alignment Motor • Rear Alignment Plate HP Sensor (PS5) • Rear Alignment Motor (M4) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Front Aligning Plate HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Front Aligning Plate Motor • Front aligning plate drive mechanism • Front Aligning Plate HP Sensor (PI106) • Front Aligning Plate Motor (M103) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E531 8001 |
| Description: | a. Stapler Motor error b. Staple HP error. a. The Staple HP Sensor was not turned OFF although 0.4 seconds had passed after the Stapler Motor operation started. b. The staple does not come off the Staple HP Sensor although the Staple Motor has been driven for 0.4 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stapler Unit • Stapler Unit (including the Stapler Motor and the Staple HP Sensor) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stapler Unit • Stapler Unit (including the Staple Motor (M111) and the Staple HP Sensor (PI50)) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E531 8002 |
| Description: | a. Stapler Motor error b. Staple HP error. a. The Staple HP Sensor was not turned ON although 0.4 seconds had passed after the Stapler Motor operation started. b. The Staple HP Sensor does not detect the staple although the Staple Motor has been driven for 0.4 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stapler Unit • Stapler Unit (including the Stapler Motor and the Staple HP Sensor) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stapler Unit • Stapler Unit (including the Staple Motor (M111) and the Staple HP Sensor (PI50)) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E532 8001 |
| Description: | a. Stapler Shift Motor error b. Stapler Shift HP error. a. The Stapler Shift HP Sensor was not turned OFF although 1 second had passed after the Stapler Shift Motor operation started. b. The stapler unit does not come off the Stapler Shift HP Sensor although the Stapler Shift Motor has been driven for 5 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stapler Shift HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Stapler Shift Motor • Stapler Shift HP Sensor (PS11) • Stapler Shift Motor (M7) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stapler Shift HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Stapler Shift Motor • Stapler Shift HP Sensor (PI110) • Stapler Shift Motor (M105) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E532 8002 |
| Description: | a. Stapler Shift Motor error b. Stapler Shift HP error. a. The Stapler Shift HP Sensor was not turned ON although 10 seconds had passed after the Stapler Shift Motor operation started. b. The Stapler Shift HP Sensor does not detect the stapler unit although the Stapler Shift Motor has been driven for 20 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stapler Shift HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Stapler Shift Motor • Stapler Shift HP Sensor (PS11) • Stapler Shift Motor (M7) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stapler Shift HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Stapler Shift Motor • Stapler Shift HP Sensor (PI110) • Stapler Shift Motor (M105) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E535 0001 |
| Description: | Return Belt Motor error. The Return Belt HP Sensor was not turned OFF although 1 second had passed after the Return Belt Motor operation started. |
| Remedy: | INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Return Belt HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Return Belt Motor • Return Belt HP Sensor (PS3) • Return Belt Motor (M2) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E535 0002 |
| Description: | Return Belt Motor error. The Return Belt HP Sensor was not turned ON although 1 second had passed after the Return Belt Motor operation started. |
| Remedy: | INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Return Belt HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Return Belt Motor • Return Belt HP Sensor (PS3) • Return Belt Motor (M2) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E535 8001 |
| Description: | Swing Guide HP error. The swing guide does not come off the Swing Guide HP Sensor although the Swing Guide Motor has been driven for 3 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Swing Guide HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Swing Guide Motor • Swing guide drive mechanism • Swing Guide HP Sensor (PI105) • Swing Guide Motor (M106) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E535 8002 |
| Description: | Swing Guide HP error. The Swing Guide HP Sensor does not detect the swing guide although the Swing Guide Motor has been driven for 3 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Swing Guide HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Swing Guide Motor • Swing guide drive mechanism • Swing Guide HP Sensor (PI105) • Swing Guide Motor (M106) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E537 8001 |
| Description: | a. Front Alignment Motor error b. Rear Aligning Plate HP error. a. The Front Alignment Plate HP Sensor was not turned OFF although 1 second had passed after the Front Alignment Motor operation started. b. The rear aligning plate does not come off the Rear Aligning Plate HP Sensor although the Rear Aligning Plate Motor has been driven for 4 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Front Alignment Plate HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Front Alignment Motor • Front Alignment Plate HP Sensor (PS4) • Front Alignment Motor (M3) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Rear Aligning Plate HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Rear Aligning Plate Motor • Rear aligning plate drive mechanism • Rear Aligning Plate HP Sensor (PI107) • Rear Aligning Plate Motor (M104) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E537 8002 |
| Description: | a. Front Alignment Motor error b. Rear Aligning Plate HP error. a. The Front Alignment Plate HP Sensor was not turned ON although 5 seconds had passed after the Front Alignment Motor operation started. b. The Rear Aligning Plate HP Sensor does not detect the rear aligning plate although the Rear Aligning Plate Motor has been driven for 4 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Front Alignment Plate HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Front Alignment Motor • Front Alignment Plate HP Sensor (PS4) • Front Alignment Motor (M3) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Rear Aligning Plate HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Rear Aligning Plate Motor • Rear aligning plate drive mechanism • Rear Aligning Plate HP Sensor (PI107) • Rear Aligning Plate Motor (M104) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E540 8001 |
| Description: | a. Tray Shift Motor error b. Tray 1 timeout error. a. The Stack Tray Paper Height Sensor was not turned ON although 5 seconds had passed after the Tray Shift Motor operation started. b. The tray does not return to its home position although the Tray 1 Shift Motor has been driven for 25 seconds. • The tray does not move to the other area although the Tray 1 Shift Motor has been driven for 5 seconds. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stack Tray Paper Height Sensor • Harnesses and connectors from the Finisher Controller PCB to the Tray Shift Motor • Stack Tray Paper Height Sensor (PS9) • Tray Shift Motor (M6) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Paper Surface Sensor • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Shift Area Sensor PCB • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Shift Motor • Tray 1 drive mechanism • Tray 1 Paper Surface Sensor (PI114) • Tray 1 Shift Area Sensor PCB (PCB4) • Tray 1 Shift Motor (M107) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E540 8002 |
| Description: | a. Tray Shift Motor error b. Tray 1 shift area error. a. The Front Alignment Plate HP Sensor was not turned OFF or the Stack Tray Lower Limit Sensor was not turned ON although 3.5 seconds had passed after the Front Alignment Motor operation started in the tray down operation. • The Front Alignment Plate HP Sensor was not turned OFF after the tray was moved down in the paper level detection operation. b. The tray exceeded the upper/lower limit before the Tray 1 Paper Surface Sensor detects the paper surface during the paper surface detection operation. • A non-contiguous area was detected during the tray shift operation. |
| Remedy: | a. INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Stack Tray Paper Height Sensor • Harnesses and connectors from the Finisher Controller PCB to the Tray Shift Motor • Stack Tray Paper Height Sensor (PS9) • Tray Shift Motor (M6) • Finisher Controller PCB (PCB1) b. STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Paper Surface Sensor • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Shift Area Sensor PCB • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Shift Motor • Tray 1 drive mechanism • Tray 1 Paper Surface Sensor (PI114) • Tray 1 Shift Area Sensor PCB (PCB4) • Tray 1 Shift Motor (M107) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E540 8003 |
| Description: | Safety switch ON error. The Swing Guide Safety Switch or Tray 1 Safety Switch was turned ON during the tray shift operation. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Paper Surface Sensor • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Shift Area Sensor • Harnesses and connectors from the Finisher Controller PCB to the Tray 1 Shift Motor • Tray 1 drive mechanism • Tray 1 Paper Surface Sensor (PI114) • Tray 1 Shift Area Sensor (PCB4) • Tray 1 Shift Motor (M107) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E542 8001 |
| Description: | Tray 2 timeout error. • The tray does not return to its home position although the Tray 2 Shift Motor has been driven for 25 seconds. • The tray does not move to the other areas although the Tray 2 Shift Motor has been driven for 5 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Tray 2 Paper Surface Sensor 1 • Harnesses and connectors from the Finisher Controller PCB to the Tray 2 Paper Surface Sensor 2 • Harnesses and connectors from the Finisher Controller PCB to the Tray 2 Shift Area Sensor • Harnesses and connectors from the Finisher Controller PCB to the Tray 2 Shift Motor • Tray 2 drive mechanism • Tray 2 Paper Surface Sensor 1 (PI115) • Tray 2 Paper Surface Sensor 2 (PI120) • Tray 2 Shift Area Sensor (PCB5) • Tray 2 Shift Motor (M108) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E542 8002 |
| Description: | Tray 2 shift area error. • The tray exceeded the upper or lower limit before the Tray 2 Paper Surface Sensor 1 detects the paper surface during the paper surface detection operation. • A non-contiguous area was detected during the tray shift operation. • The tray reached the area that passed through Tray 2 Paper Surface Sensor 2 before the Tray 2 Paper Surface Sensor 2 detects the paper surface during the tray escape operation. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Tray 2 Paper Surface Sensor 1 • Harnesses and connectors from the Finisher Controller PCB to the Tray 2 Paper Surface Sensor 2 • Harnesses and connectors from the Finisher Controller PCB to the Tray 2 Shift Area Sensor • Harnesses and connectors from the Finisher Controller PCB to the Tray 2 Shift Motor • Tray 2 drive mechanism • Tray 2 Paper Surface Sensor 1 (PI115) • Tray 2 Paper Surface Sensor 2 (PI120) • Tray 2 Shift Area Sensor (PCB5) • Tray 2 Shift Motor (M108) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E551 0001 |
| Description: | Buffer Pass Power Supply Cooling Fan error. The fan lock signal is detected 1.2 seconds or more while the fan operates. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Buffer Pass Controller PCB to the Buffer Pass Power Supply Cooling Fan • Buffer Pass Power Supply Cooling Fan (FM201) • Buffer Pass Controller PCB (PCB201) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E551 0002 |
| Description: | Buffer Pass Power Supply Cooling Fan error. The fan lock signal is released when the fan stops. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Buffer Pass Controller PCB to the Buffer Pass Power Supply Cooling Fan • Buffer Pass Power Supply Cooling Fan (FM201) • Buffer Pass Controller PCB (PCB201) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E551 0003 |
| Description: | Buffer Pass Cooling Fan error. The fan lock signal is detected 1.2 seconds or more while the fan operates. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Buffer Pass Controller PCB to the Buffer Pass Cooling Fan • Buffer Pass Cooling Fan (FM202) • Buffer Pass Controller PCB (PCB201) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E551 0004 |
| Description: | Buffer Pass Cooling Fan error. The fan lock signal is released when the fan stops. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Buffer Pass Controller PCB to the Buffer Pass Cooling Fan • Buffer Pass Cooling Fan (FM202) • Buffer Pass Controller PCB (PCB201) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E577 0002 |
| Description: | Paddle Motor error. • The Return Belt HP Sensor was not turned ON although 1 second had passed after the Paddle Motor operation started. • The last paddle operation is not finished when driving the Paddle Motor. |
| Remedy: | INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Return Belt HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Paddle Motor • Return Belt HP Sensor (PS3) • Paddle Motor (M10) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E577 8001 |
| Description: | Paddle Motor error. • The Return Belt HP Sensor was not turned ON although 1 second had passed after the Paddle Motor operation started. • The last paddle operation is not finished when driving the Paddle Motor. |
| Remedy: | INNER FIN-G1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Return Belt HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Paddle Motor • Return Belt HP Sensor (PS3) • Paddle Motor (M10) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E584 0002 |
| Description: | Shutter HP error. The Shutter HP Sensor does not detect the shutter although the Stack Ejection Motor has been driven for 3 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Shutter HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Stack Ejection Motor • Harnesses and connectors from the Finisher Controller PCB to the Stack Ejection Lower Roller Clutch • Harnesses and connectors from the Finisher Controller PCB to the Shutter Clutch • Shutter drive mechanism • Shutter HP Sensor (PI113) • Stack Ejection Motor (M102) • Stack Ejection Lower Roller Clutch (CL102) • Shutter Clutch (CL101) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E584 8001 |
| Description: | Shutter HP error. The shutter does not come off the Shutter HP Sensor although the Stack Ejection Motor has been driven for 3 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Finisher Controller PCB to the Shutter HP Sensor • Harnesses and connectors from the Finisher Controller PCB to the Stack Ejection Motor • Harnesses and connectors from the Finisher Controller PCB to the Stack Ejection Lower Roller Clutch • Harnesses and connectors from the Finisher Controller PCB to the Shutter Clutch • Shutter drive mechanism • Shutter HP Sensor (PI113) • Stack Ejection Motor (M102) • Stack Ejection Lower Roller Clutch (CL102) • Shutter Clutch (CL101) • Finisher Controller PCB (PCB1) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Adjustment when Replacing the Parts" in the Service Manual. |
| Error code: | E5F0 8001 |
| Description: | Paper positioning Plate HP error. The Saddle Paper Positioning Plate HP Sensor does not detect the paper positioning plate although the Saddle Paper Positioning Plate Motor has been driven for 1500 pulses. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Positioning Plate HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Positioning Plate Motor • Paper positioning plate drive mechanism • Saddle Paper Positioning Plate HP Sensor (PI7) • Saddle Paper Positioning Plate Motor (M4) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F0 8002 |
| Description: | Paper positioning Plate HP error. The paper positioning plate does not come off the Saddle Paper Positioning Plate HP Sensor although the Saddle Paper Positioning Plate Motor has been driven for 300 pulses. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Positioning Plate HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Positioning Plate Motor • Paper positioning plate drive mechanism • Saddle Paper Positioning Plate HP Sensor (PI7) • Saddle Paper Positioning Plate Motor (M4) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F1 8001 |
| Description: | Saddle Paper Folding Motor clock error. The drive speed of the Saddle Paper Folding Motor became 5 mm/sec or less (2 mm/sec or less at initial operation). |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Folding Motor Clock Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Folding HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Folding Motor • Paper folding roller drive mechanism • Saddle Paper Folding Motor Clock Sensor (PI4) • Saddle Paper Folding HP Sensor (PI21) • Saddle Paper Folding Motor (M2) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F1 8002 |
| Description: | Saddle Paper Folding HP error. The Saddle Paper Folding HP Sensor does not detect the home position of the paper fold roller although the Saddle Paper Folding Motor has been driven for 2 seconds (3 seconds at initial operation). |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Folding Motor Clock Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Folding HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Folding Motor • Paper folding roller drive mechanism • Saddle Paper Folding Motor Clock Sensor (PI4) • Saddle Paper Folding HP Sensor (PI21) • Saddle Paper Folding Motor (M2) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F2 8001 |
| Description: | Saddle Guide HP error. The Saddle Guide HP Sensor does not detect the guide plate although the Saddle Guide Motor has been driven for 700 pulses. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Guide HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Guide Motor • Guide plate drive mechanism • Saddle Guide HP Sensor (PI13) • Saddle Guide Motor (M3) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F2 8002 |
| Description: | Saddle Guide HP error. The guide plate does not come off the Saddle Guide HP Sensor although the Saddle Guide Motor has been driven for 50 pulses. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Guide HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Guide Motor • Guide plate drive mechanism • Saddle Guide HP Sensor (PI13) • Saddle Guide Motor (M3) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F3 8001 |
| Description: | Saddle Alignment Plate HP error. The Saddle Alignment Plate HP Sensor does not detect the alignment plate although the Saddle Alignment Motor has been driven for 500 pulses. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Alignment Plate HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Alignment Motor • Alignment plate drive mechanism • Saddle Alignment Plate HP Sensor (PI5) • Saddle Alignment Motor (M5) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F3 8002 |
| Description: | Saddle Alignment Plate HP error. The alignment plate does not come off the Saddle Alignment Plate HP Sensor although the Saddle Alignment Motor has been driven for 50 pulses. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Alignment Plate HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Alignment Motor • Alignment plate drive mechanism • Saddle Alignment Plate HP Sensor (PI5) • Saddle Alignment Motor (M5) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F4 8001 |
| Description: | Stitcher (Rear) HP error. The Stitcher HP Switch (Rear) does not detect the stitcher (rear) although the Stitcher Motor (Rear) has been driven for 0.48 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Stitcher Unit (Rear) • Stitcher Unit (Rear) (including the Stitcher Motor (Rear) (M6) and the Stitcher HP Switch (Rear) (SW5)) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F4 8002 |
| Description: | Stitcher (Rear) HP error. The stitcher (rear) does not come off the Stitcher HP Switch (Rear) although the Stitcher Motor (Rear) has been driven for 0.48 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Stitcher Unit (Rear) • Stitcher Unit (Rear) (including the Stitcher Motor (Rear) (M6) and the Stitcher HP Switch (Rear) (SW5)) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F5 8001 |
| Description: | Stitcher (Front) HP error. The Stitcher HP Switch (Front) does not detect the stitcher (front) although the Stitcher Motor (Front) has been driven for 0.48 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Stitcher Unit (Front) • Stitcher Unit (Rear) (including the Stitcher Motor (Front) (M7) and the Stitcher HP Switch (Front) (SW7)) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F5 8002 |
| Description: | Stitcher (Front) HP error. The stitcher (front) does not come off the Stitcher HP Switch (Front) although the Stitcher Motor (Front) has been driven for 0.48 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Stitcher Unit (Front) • Stitcher Unit (Rear) (including the Stitcher Motor (Front) (M7) and the Stitcher HP Switch (Front) (SW7)) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F6 8001 |
| Description: | Paper Pushing Plate HP error. The Saddle Paper Pushing Plate HP Sensor does not detect the paper pushing plate although the Saddle Paper Pushing Plate Motor has been driven for 0.5 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate Motor • Paper pushing plate drive mechanism • Saddle Paper Pushing Plate HP Sensor (PI14) • Saddle Paper Pushing Plate Motor (M8) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F6 8002 |
| Description: | Paper Pushing Plate HP error. The paper pushing plate does not come off the Saddle Paper Pushing Plate HP Sensor although the Saddle Paper Pushing Plate Motor has been driven for 0.15 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate HP Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate Motor • Paper pushing plate drive mechanism • Saddle Paper Pushing Plate HP Sensor (PI14) • Saddle Paper Pushing Plate Motor (M8) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F6 8003 |
| Description: | Saddle Paper Pushing Plate Motor clock error. The clock detection of the Saddle Paper Pushing Plate Motor became 6 clocks or less. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate Motor Clock Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate Motor • Paper pushing plate drive mechanism • Saddle Paper Pushing Plate Motor Clock Sensor (PI1) • Saddle Paper Pushing Plate Motor (M8) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F6 8004 |
| Description: | Paper Pushing Plate position error. The paper pushing plate does not come off the paper folding position although the Saddle Paper Pushing Plate Motor has been driven for 0.1 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate Top Position Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate Motor • Paper pushing plate drive mechanism • Saddle Paper Pushing Plate Top Position Sensor (PI15) • Saddle Paper Pushing Plate Motor (M8) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E5F6 8005 |
| Description: | Paper Pushing Plate position error. The paper pushing plate does not return to the paper pushing position although the Saddle Paper Pushing Plate Motor has been driven for 0.5 seconds. |
| Remedy: | STAPLE FIN-U1/BOOKLET FIN-U1 [Related parts] • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate Top Position Sensor • Harnesses and connectors from the Saddle Stitcher Controller PCB to the Saddle Paper Pushing Plate Motor • Paper pushing plate drive mechanism • Saddle Paper Pushing Plate Top Position Sensor (PI15) • Saddle Paper Pushing Plate Motor (M8) • Saddle Stitcher Controller PCB (PCB2) [Remedy] Check/replace the corresponding harnesses/cables or connectors or the parts. |
| Error code: | E602 0001 |
| Description: | Insufficient HDD capacity |
| Remedy: | Replace the HDD. |
| Error code: | E602 0101 |
| Description: | HDD error. An error was detected in the PDL-related file storage area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 3. After replacing the HDD, format the HDD. 4. Replace the Main Controller PCB. |
| Error code: | E602 0111 |
| Description: | HDD error. An error was detected in the PDL-related file storage are(File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 3. After replacing the HDD, format the HDD. 4. Replace the Main Controller PCB. |
| Error code: | E602 0201 |
| Description: | HDD error. An error was detected in the storage area of image data after startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 3 and later. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 6. After replacing the HDD, format the HDD. 7. Replace the Main Controller PCB. |
| Error code: | E602 0211 |
| Description: | HDD error. An error was detected in the storage area of image data after startup. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 3 and later. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 6. After replacing the HDD, format the HDD. 7. Replace the Main Controller PCB. |
| Error code: | E602 0301 |
| Description: | HDD error. An error was detected in the MEAP-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 3 and later. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 6. After replacing the HDD, format the HDD. 7. Replace the Main Controller PCB. |
| Error code: | E602 0311 |
| Description: | HDD error. An error was detected in the MEAP-related area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 3 and later. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 6. After replacing the HDD, format the HDD. 7. Replace the Main Controller PCB. |
| Error code: | E602 0401 |
| Description: | HDD error. Logical partition error was detected. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 3. After replacing the HDD, format the HDD. 4. Replace the Main Controller PCB. |
| Error code: | E602 0411 |
| Description: | HDD error. Logical partition error was detected. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 3. After replacing the HDD, format the HDD. 4. Replace the Main Controller PCB. |
| Error code: | E602 0501 |
| Description: | HDD error. An error was detected in the storage area of image data after startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 3 and later. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 6. After replacing the HDD, format the HDD. 7. Replace the Main Controller PCB. |
| Error code: | E602 0511 |
| Description: | HDD error. An error was detected in the storage area of image data after startup. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] • Cable between the Main Controller PCB (UN05) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, perform Remedy 3 and later. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [1] Disk Format (HDD format) using SST or a USB memory. [Reference] All data in the HDD is deleted. 6. After replacing the HDD, format the HDD. 7. Replace the Main Controller PCB. |
| Error code: | E614 0001 |
| Description: | Flash PCB error. The Flash PCB could not be recognized, or the Flash PCB was not formatted. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 4. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 5. Replace the Main Controller PCB. |
| Error code: | E614 0002 |
| Description: | Error in file system on the Flash PCB. The file system could not be initialized normally at startup. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 4. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 5. Replace the Main Controller PCB. |
| Error code: | E614 0006 |
| Description: | Error in file system on the Flash PCB. Bootable was not found on the Flash PCB. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 4. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 5. Replace the Main Controller PCB. |
| Error code: | E614 0101 |
| Description: | Flash PCB error. An error was detected in the system area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0111 |
| Description: | Flash PCB error. An error was detected in the system area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0201 |
| Description: | Flash PCB error. An error was detected in the system area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0211 |
| Description: | Flash PCB error. An error was detected in the system area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual |
| Error code: | E614 0301 |
| Description: | Flash PCB error. An error was detected in the system area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0311 |
| Description: | Flash PCB error. An error was detected in the system area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0401 |
| Description: | Flash PCB error. Logical partition error was detected. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0411 |
| Description: | Flash PCB error. Logical partition error was detected. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB to check that it is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Obtain the necessary backup data by referring to the backup data list. 4. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 5. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 6. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0501 |
| Description: | Flash PCB error. An error was detected in the general application-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. • When prioritizing clearing of the error, perform Remedy 3 and later. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 6. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 7. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0511 |
| Description: | Flash PCB error. An error was detected in the general application-related area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. • When prioritizing clearing of the error, perform Remedy 3 and later. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 6. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 7. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0601 |
| Description: | Flash PCB error. An error was detected in the license-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Obtain the necessary backup data by referring to the backup data list. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 3. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 4. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0611 |
| Description: | Flash PCB error. An error was detected in the license-related area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Obtain the necessary backup data by referring to the backup data list. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 3. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 4. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 0701 |
| Description: | Flash PCB error. An error was detected in system setting value (service mode, etc.) storage area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. • When prioritizing clearing of the error, perform Remedy 3 and later. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 6. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 7. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual |
| Error code: | E614 0711 |
| Description: | Flash PCB error. An error was detected in system setting value (service mode, etc.) storage area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] • Flash PCB (UN61) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASS`Y) [Remedy] Perform the following in the order while checking whether the error is cleared. • Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 3. • When prioritizing clearing of the error, perform Remedy 3 and later. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] Only the data in the corresponding partitions is deleted. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CLEAR". Then, turn OFF and then ON the main power. [Reference] All the partitions that can be deleted are deleted. 5. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 6. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 7. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E614 4000 |
| Description: | Error in file system on the Flash PCB. The OS could not be recognized. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Disconnect and then connect the connectors of the Flash PCB (UN61) and the Main Power Switch, and check if there is any bent pin or cable disconnection. 2. Format the system. 2-1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2-2. Reinstall the system software using SST or a USB memory. 3. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. |
| Error code: | E615 0001 |
| Description: | Error in self-diagnosis of the encryption module.An error was detected in self-diagnosis of the encryption library. |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. • Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After reinstalling the system software using SST or a USB memory, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 4. After replacing the Flash PCB (UN61), reinstall the system software using SST or a USB memory. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E674 0001 |
| Description: | Fax Board communication error. An error was detected for the specified number of times in communication with the Fax Board. |
| Remedy: | [Related parts] • Harness between the Fax Board and the Main Controller PCB (UN05/J30) (Unit of replacement: CABLE, SIGNAL) • Fax Board • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E674 0004 |
| Description: | Fax Board communication error. A communication error occurred when accessing the modem IC used for fax. |
| Remedy: | [Related parts] • Harness between the Fax Board and the Main Controller PCB (UN05/J30) (Unit of replacement: CABLE, SIGNAL) • Fax Board • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts |
| Error code: | E674 0008 |
| Description: | Fax Board communication error. A communication error occurred when accessing the port IC used for On Board Fax |
| Remedy: | [Related parts] • Harness between the Fax Board and the Main Controller PCB (UN05/J30) (Unit of replacement: CABLE, SIGNAL) • Fax Board • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts |
| Error code: | E674 000C |
| Description: | Fax Board communication error. An error was detected when accessing the modem IC and the port IC used for fax. |
| Remedy: | [Related parts] • Harness between the Fax Board and the Main Controller PCB (UN05/J30) (Unit of replacement: CABLE, SIGNAL) • Fax Board • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E674 0010 |
| Description: | Fax Board communication error. A communication error occurred when opening the Timer Device used for fax. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E674 0011 |
| Description: | Fax Board communication error. A communication error occurred when starting the Timer Device used for fax. |
| Remedy: | [Remedy] Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E674 0020 |
| Description: | Fax Board communication error. An error occurred in the modem IC used for fax. |
| Remedy: | [Related parts] • Harness between the Fax Board and the Main Controller PCB (UN05/J30) (Unit of replacement: CABLE, SIGNAL) • Fax Board • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E674 0100 |
| Description: | Fax Board communication error. After completion of fax communication, writing of the communication information (log) failed, and the log could not be read. |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [CAUTION] The previous communication information (log) will be cleared by turning OFF and then ON the main power. |
| Error code: | E674 0200 |
| Description: | HDD access error. An error occurred when accessing the HDD. |
| Remedy: | [Related parts] • HDD (Unit of replacement: HARD DISK DRIVE) • Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. After deleting the system software using a USB memory, reinstall it using SST or a USB memory. 2. After replacing the HDD, execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory. 3. Replace the Main Controller PCB. |
| Error code: | E713 0010 |
| Description: | Communication error. Communication between the DC Controller PCB and the Finisher timed out. |
| Remedy: | [Related parts] a. STAPLE/BOOKLET FINISHER-U1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • Harness between the Low Voltage Power Supply PCB (UN01/ J306) and the Relay Path Unit (J1186) (Unit of replacement: CABLE, HEATER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES b. INNER FINISHER-G1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E713 0011 |
| Description: | Communication error. A communication error between the DC Controller PCB and the Finisher was detected. |
| Remedy: | [Related parts] a. STAPLE/BOOKLET FINISHER-U1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • Harness between the Low Voltage Power Supply PCB (UN01/ J306) and the Relay Path Unit (J1186) (Unit of replacement: CABLE, HEATER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES b. INNER FINISHER-G1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E713 0020 |
| Description: | Communication error. A communication error between the DC Controller PCB and the Finisher was detected |
| Remedy: | [Related parts] a. STAPLE/BOOKLET FINISHER-U1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • Harness between the Low Voltage Power Supply PCB (UN01/ J306) and the Relay Path Unit (J1186) (Unit of replacement: CABLE, HEATER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES b. INNER FINISHER-G1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E713 0021 |
| Description: | Communication error. A communication error between the DC Controller PCB and the Finisher was detected. |
| Remedy: | [Related parts] a. STAPLE/BOOKLET FINISHER-U1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • Harness between the Low Voltage Power Supply PCB (UN01/ J306) and the Relay Path Unit (J1186) (Unit of replacement: CABLE, HEATER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES b. INNER FINISHER-G1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E713 0022 |
| Description: | Communication error. A communication error between the DC Controller PCB and the Finisher was detected. |
| Remedy: | [Related parts] a. STAPLE/BOOKLET FINISHER-U1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • Harness between the Low Voltage Power Supply PCB (UN01/ J306) and the Relay Path Unit (J1186) (Unit of replacement: CABLE, HEATER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES b. INNER FINISHER-G1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E713 0030 |
| Description: | Communication error. Communication between the DC Controller PCB and the Finisher was not completed. |
| Remedy: | [Related parts] a. STAPLE/BOOKLET FINISHER-U1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • Harness between the Low Voltage Power Supply PCB (UN01/ J306) and the Relay Path Unit (J1186) (Unit of replacement: CABLE, HEATER) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES b. INNER FINISHER-G1 • Harnesses from the DC Controller PCB to the Finisher Controller PCB 1. DC Controller PCB (UN04/J182) to Relay Path Unit (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) 2. Relay Path Unit to Finisher Controller PCB • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Relay Path Unit • Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E719 0001 |
| Description: | Coin vendor error. The coin vendor which was connected before turning OFF the main power was not connected at power-on. |
| Remedy: | [Related parts] Cable between the charging management equipment and the host machine [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Reference] When operating the machine without the charging management equipment, execute "COPIER> FUNCTION> CLEAR> ERR". (It is designed to generate an error to prevent the misuse by removing the charging management equipment.) |
| Error code: | E719 0002 |
| Description: | Coin vendor error. IPC error when the coin vendor is running • Open circuit of the IPC, or IPC communication could not be recovered. • Open circuit of the pickup/delivery signal cable was detected. • Invalid connection was detected |
| Remedy: | [Related parts] Cable between the charging management equipment and the host machine [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Reference] When operating the machine without the charging management equipment, execute "COPIER> FUNCTION> CLEAR> ERR". (It is designed to generate an error to prevent the misuse by removing the charging management equipment.) |
| Error code: | E719 0003 |
| Description: | Coin vendor error. A communication error with the coin vendor was detected during unit price acquisition at startup. |
| Remedy: | [Related parts] Cable between the charging management equipment and the host machine [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Reference] When operating the machine without the charging management equipment, execute "COPIER> FUNCTION> CLEAR> ERR". (It is designed to generate an error to prevent the misuse by removing the charging management equipment.) |
| Error code: | E719 0031 |
| Description: | Card Reader communication error. Communication with the Card Reader could not be established at startup |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the harness between the Card Reader and the Main Controller PCB (UN05/J14). 2. Replace the Card Reader. [Reference] In the case of operating the device without the Card Reader which had been used, execute "COPIER> FUNCTION> CLEAR> CARD" after removing the Card Reader. |
| Error code: | E719 0032 |
| Description: | Card Reader communication error. Although communication with the Card Reader was available at startup, it became unavailable in the middle of it. |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the harness between the Card Reader and the Main Controller PCB (UN05/J14). 2. Replace the Card Reader. [Reference] In the case of operating the device without the Card Reader which had been used, execute "COPIER> FUNCTION> CLEAR> CARD" after removing the Card Reader. |
| Error code: | E720 0001 |
| Description: | Error due to non-compatible Finisher. A finisher which cannot be connected to the host machine was detected |
| Remedy: | [Remedy] Connect the finisher (INNER FINISHER-G1, BOOKLET/STAPLE FINISHER-U1) for this model |
| Error code: | E730 A006 |
| Description: | PDL communication error. Response from PDL could not be detected |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Select "Settings/Registration> Function Settings> Printer> Printer Settings> Utility> Initialize Printer", and execute PDL reset processing. 2. Reinstall the system software. 3. Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E730 A007 |
| Description: | Mismatch of PDL version. Version of the host machine control software and version of PDL control software were different |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Reinstall the system software. 2. Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E730 B013 |
| Description: | PDL embedded font error. Font data was corrupted. |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Reinstall the system software. 2. Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E732 0001 |
| Description: | Scanner communication error |
| Causes: | DDI-S communication error. |
| Remedy: | [Related parts] • Flexible Cable between the Scanner Unit (CIS01, CIS02/J911) and the Main Controller PCB (UN81/J8101) (Unit of replacement: CABLE, FLAT) • Scanner Unit (CIS01/CIS02) (Unit of replacement: CONTACT IMAGE SENSOR ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E732 0010 |
| Description: | Scanner communication error |
| Causes: | DDI-S communication error (Vsync detection error) |
| Remedy: | [Related parts] • Flexible Cable between the Scanner Unit (CIS01, CIS02/J911) and the Main Controller PCB (UN81/J8101) (Unit of replacement: CABLE, FLAT) • Scanner Unit (CIS01/CIS02) (Unit of replacement: CONTACT IMAGE SENSOR ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E733 0000 |
| Description: | Printer communication error |
| Causes: | Communication error between the Engine Controller PCB and the Main Controller PCB occurred. |
| Remedy: | 1. Check the connection of connector between the Engine Controller PCB and the Main Controller PCB. 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. 4. Replace the Engine Controller PCB. |
| Error code: | E733 0001 |
| Description: | Error in printer communication (illegal communication after establishing communication, parity error) |
| Causes: | Communication error occurred after normal startup. |
| Remedy: | 1) Turn OFF and then ON the power. 2) Replace the Engine Controller PCB. |
| Error code: | E733 0002 |
| Description: | Printer communication error |
| Causes: | DDI-P communication error (invalid packet) |
| Remedy: | [Related parts] • Flexible Cable between the DC Controller PCB (UN04/J112) and the Main Controller PCB (UN81/J7001) (Unit of replacement: CABLE, FLAT) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the harness between the DC Controller PCB and the Main Controller PCB. 2. Turn ON the power, and check if the initialization is executed at startup. 2-1. If the initialization is not executed, replace the DC Controller PCB. 2-2. If the initialization is executed, replace the Main Controller PCB. |
| Error code: | E733 0F01 |
| Description: | Printer communication error |
| Causes: | A communication error that can be recovered by reboot. If it is detected again after reboot, E733-0001 is generated. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E733 0F02 |
| Description: | Printer communication error |
| Causes: | A communication error that can be recovered by reboot. If it is detected again after reboot, E733-0002 is generated. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E733 F001 |
| Description: | Printer communication error |
| Causes: | Disconnection of the Flexible Cable between the Main Controller PCB and the DC Controller PCB was detected. |
| Remedy: | Check/replace the Flexible Cable between the DC Controller PCB (UN04/J112) and the Main Controller PCB (UN81/J7001) (unit of replacement: CABLE, FLAT). |
| Error code: | E733 F002 |
| Description: | Printer communication error |
| Causes: | Disconnection of the Flexible Cable between the Main Controller PCB and the Y/M/C/Bk Laser Driver PCB was detected. |
| Remedy: | Check/replace the Flexible Cable between the Y/M/C/Bk Laser Driver PCB (UN05/J201) and the Main Controller PCB (UN81/J7002). (Unit of replacement: CABLE, FLAT) |
| Error code: | E743 0001 |
| Description: | DDI communication error. Software sequence error |
| Remedy: | Turn OFF and then ON the main power. |
| Error code: | E744 0001 |
| Description: | Language file version error |
| Causes: | Language file version was not matched with the main program. |
| Remedy: | Install the set of the controller firmware. |
| Error code: | E744 4000 |
| Description: | Engine ID error |
| Causes: | Invalid engine connection was detected. |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Check the Engine Controller PCB. 3. Install the Engine Controller PCB. 4. Install the set of the controller firmware. 5. Check the model code. (When the model code and the engine code are mismatched, E744-4000 occurs.) |
| Error code: | E746 0022 |
| Description: | Image Analysis Board error. Wrong version of the Image Analysis Board was detected. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB memory. 2. After replacing the Image Analysis Board, perform step 1. |
| Error code: | E746 0023 |
| Description: | Image Analysis Board error. Communication from the Image Analysis Board could not be detected. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Check that the Image Analysis Board is installed properly by removing and then installing it again. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. After replacing the Image Analysis Board, reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB memory. |
| Error code: | E746 0024 |
| Description: | Image Analysis Board error. An error in the operation of the Image Analysis Board was detected |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Check that the Image Analysis Board is installed properly by removing and then installing it again. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. After replacing the Image Analysis Board, reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB memory. |
| Error code: | E746 0031 |
| Description: | TPM error. A communication error between the Main Controller PCB and the TPM PCB was detected at startup. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. After turning OFF the main power, replace the TPM PCB. (Unit of replacement: TPM PCB ASSEMBLY) 3. If the TPM key was backed up, restore the key. 3-1. Connect the USB memory which stores the TPM key. 3-2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3-3. Enter the password set at backup operation. 3-4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power. |
| Error code: | E746 0032 |
| Description: | TPM error. Mismatch of the TPM key was detected. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Format the system. 1-1. Enter safe mode using (2+8) startup, and execute [4]: Clear/Format> [2]: Flash Format (Flash format) using a USB memory. 1-2. Reinstall the system software using SST or a USB memory. 2. Replace the TPM PCB. (Unit of replacement: TPM PCB ASSEMBLY) 3. If the TPM key was backed up, restore the key. 3-1. Connect the USB memory which stores the TPM key. 3-2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3-3. Enter the password set at backup operation. 3-4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power. |
| Error code: | E746 0033 |
| Description: | TPM error. It was detected that data in TPM was inconsistent. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. Perform the appropriate remedy according to the status whether the TPM key was backed up. a. If the TPM key was backed up, restore the key. 1. Connect the USB memory which stores the TPM key. 2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3. Enter the password set at backup operation. 4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power. b. If the TPM key was not backed up, format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory |
| Error code: | E746 0034 |
| Description: | TPM auto-recovery error. The error occurred when clearing HDD while TPM setting was ON. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. a. If the error is cleared, execute "Settings/Registration> Log In> Management Settings> Data Management> Initialize All Data/ Settings". b. If the error is not cleared, format the system. 1. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 2. Reinstall the system software using SST or a USB memory. 2. If the TPM key was backed up, restore the key. 2-1. Connect the USB memory which stores the TPM key. 2-2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 2-3. Enter the password set at backup operation. 2-4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power |
| Error code: | E746 0035 |
| Description: | TPM version error. TPM PCB which cannot be used in this machine was installed. |
| Remedy: | Install the TPM PCB for this model. (Unit of replacement: TPM PCB ASSEMBLY) |
| Error code: | E748 2010 |
| Description: | Flash PCB error / HDD error. IPL (startup program) was not found, or the HDD could not be recognized. |
| Remedy: | • Cable between the Main Controller PCB (UN05/J29 and J23) and the HDD (Unit of replacement: CABLE, SATA POWER, CABLE, SATA SIGNAL) • Flash PCB (UN61) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Disconnect the cable between the Main Controller PCB and the HDD, and turn ON the main power. a. When the error code has not been changed: 1. Obtain the necessary backup data by referring to the backup data list. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/ Format> [2] Flash Format (Flash format) using a USB memory. 3. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 4. Restore the backup data. b. When the error code has been changed to another one, see the remedy for the corresponding code. [Reference] For backup and restoration, refer to "Adjustment> Actions after Replacement" and "Appendix> Backup Data List" in the Service Manual |
| Error code: | E748 9000 |
| Description: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E749 0005 |
| Description: | Error due to change in hardware configuration. There was a change in option configuration that requires turning OFF and then ON the main power. On the screen, only the message "Turn the main power switch OFF and ON" is displayed instead of displaying the error code. The error log is not recorded in COPIER> DISPLAY> ERR |
| Remedy: | Turn OFF and then ON the main power. [Reference] Options are recognized again by turning OFF and then ON the main power. |
| Error code: | E749 0006 |
| Description: | Error due to change in hardware configuration. There was a change in option configuration during quick off. On the screen, only the message "Turn the main power switch OFF and ON" is displayed instead of displaying the error code. The error log is not recorded in COPIER> DISPLAY> ERR |
| Remedy: | Turn OFF and then ON the main power. [Reference] Options are recognized again by turning OFF and then ON the main power |
| Error code: | E753 0001 |
| Description: | Download error. Update of the Main Controller PCB ended in failure. (Power supply was interrupted during update without backup.) |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Reinstall the system software using SST or a USB memory. 2. After replacing the Flash PCB (UN61), reinstall the system software using SST or a USB memory. 3. Collect debug log and contact to the sales company. |
| Error code: | E804 0000 |
| Description: | Power Supply Cooling Fan error |
| Causes: | It was detected that the Power Supply Cooling Fan was locked. |
| Remedy: | [Related parts] • Harness between the Low-voltage Power Supply PCB (UN01/J323) and the Power Supply Cooling Fan (FM05/J5215) (Unit of replacement: CABLE, POWER SUPPLY) • Harness between the Low-voltage Power Supply PCB (UN01/J321) and the Main Controller PCB (UN81/J7010) (Unit of replacement: CABLE, POWER SUPPLY) • Power Supply Cooling Fan (FM05) • Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E806 0100 |
| Description: | Drum Unit Suction Cooling Fan error |
| Causes: | The Drum Unit Suction Cooling Fan did not rotate for the specified period of time since the start of drive. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J180) and the Primary Transfer High-voltage PCB (UN03/J271) (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) • Harness between the Primary Transfer High-voltage PCB (UN03/J272) and the Drum Unit Suction Cooling Fan (FM01) • Drum Unit Suction Cooling Fan (FM01) • Primary Transfer High-voltage PCB (UN03) (Unit of replacement: 1ST TRANSFER H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E806 0101 |
| Description: | Drum Unit Suction Cooling Fan error |
| Causes: | The Drum Unit Suction Cooling Fan rotated for more than the specified period of time after the stop of drive. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J180) and the Primary Transfer High-voltage PCB (UN03/J271) (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.) • Harness between the Primary Transfer High-voltage PCB (UN03/J272) and the Drum Unit Suction Cooling Fan (FM01) • Drum Unit Suction Cooling Fan (FM01) • Primary Transfer High-voltage PCB (UN03) (Unit of replacement: 1ST TRANSFER H.V. PCB ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E806 0200 |
| Description: | Drive Unit Cooling Fan error |
| Causes: | The Drive Unit Cooling Fan did not rotate for the specified period of time since the start of drive. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J191) and the Drive Unit Cooling Fan (FM02) • Drive Unit Cooling Fan (FM02) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E806 0201 |
| Description: | Drive Unit Cooling Fan error |
| Causes: | The Drive Unit Cooling Fan rotated for more than the specified period of time after the stop of drive. |
| Remedy: | [Related parts] • Harness between the DC Controller PCB (UN04/J191) and the Drive Unit Cooling Fan (FM02) • Drive Unit Cooling Fan (FM02) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. |
| Error code: | E808 0001 |
| Description: | Low-voltage power supply failure |
| Causes: | Failure detection of Low Voltage Power Supply PCB |
| Remedy: | Replace the Low-voltage power supply unit. |
| Error code: | E808 0002 |
| Description: | Fixing Assembly_Edge Right Cooling Fan error |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. 1. Replace the Edge Right Cooling Fan. 2. Replace the DC Controller Board. |
| Error code: | E811 0000 |
| Description: | Fuse in the Fixing Fuse PCB blowout error. The fuse in the Fixing Fuse PCB was not blown out at power-on. |
| Remedy: | [Related parts] • Fixing Fuse PCB (UN31) (Unit of replacement: FIXING FUSE PCB ASSEMBLY) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Harnesses from the DC Controller PCB to the Fixing Fuse PCB 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DB) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LB) to Fixing Fuse PCB (Unit of replacement: CABLE, DRAWER RELAY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E880 0001 |
| Description: | Controller Fan error. It was detected that the Controller Fan was locked. |
| Remedy: | Replace the Main Controller PCB (UN05). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) |
| Error code: | E881 0001 |
| Description: | Board over heat error. It was detected that temperature of the CPU of the Main Controller PCB was abnormal. |
| Remedy: | [Related parts] Main Controller PCB (UN05) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Perform the following in the order while checking whether the error is cleared. a. If the error occurred during a service visit and then occurred again, replace the Main Controller PCB. b. If the error does not occur during a service visit but is found in the log: 1. Clean the inlet on the side where the fan is installed and remove dust. 2. Remove dust from the fan in the Controller Box. 3. If the space on the side where the fan is installed is less than 10 cm, ask the customer to secure enough space. |
| Error code: | E890 0001 |
| Description: | Temperature detection error. The Environment Sensor did not detect change in temperature. |
| Remedy: | [Related parts] • Harnesses from the DC Controller PCB to the Environment Sensor Unit 1. DC Controller PCB (UN04/J133) to Relay Connector (9P) (Unit of replacement: CABLE, SENSOR) 2. Relay Connector (9P) to Environment Sensor Unit (UN27/ J1107) (Unit of replacement: CABLE, INTERLOCK SWITCH) • Environment Sensor Unit (UN27) (Unit of replacement: ENVIRONMENT SENSOR ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E890 0002 |
| Description: | Temperature detection error. The thermistor in the Laser Scanner Unit consecutively detected a temperature outside of the specified range. |
| Remedy: | [Related parts] • Harness between the Y/M Laser Driver PCB (UN08/J204) and the Thermistor in the Laser Scanner Unit (TH04) (Unit of replacement: LASER SCANNER ASSEMBLY) • Y/M Laser Driver PCB (UN08) (Unit of replacement: LASER SCANNER ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After replacement of the Laser Driver PCB, execute "Settings/ Registration> Adjustment/Maintenance> Adjust Image Quality> Auto Correct Color Mismatch". |
| Error code: | E890 0003 |
| Description: | Temperature detection error. The thermistor in the Laser Driver PCB consecutively detected a temperature outside of the specified range. |
| Remedy: | [Related parts] • Flat Cable between the Y/M Laser Driver PCB (UN08/ J203) and the C/Bk Laser Driver PCB (UN09/J801) (Unit of replacement: CABLE, FLAT) • C/Bk Laser Driver PCB (UN09) (Unit of replacement: LASER SCANNER ASSEMBLY) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After replacement of the Laser Driver PCB, execute "Settings/ Registration> Adjustment/Maintenance> Adjust Image Quality> Auto Correct Color Mismatch". |
| Error code: | E996 0071 |
| Description: | Sequence jam error |
| Causes: | 30 sec JAM timer (timing error jam), which sets at the timing when ADF motor is driven, occurs time out. |
| Remedy: | 1. Check connection of the connectors. 2. Replace the main controller PCB (PCB2). 3. Replace the reader unit. |
| Error code: | E996 0CA1 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting “COPIER > OPTION> FNC-SW> JM-ERR-D” to “0” (default), it is handled as a jam, instead of an error. |
| Error code: | E996 0CA2 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting “COPIER > OPTION> FNC-SW> JM-ERR-D” to “0” (default), it is handled as a jam, instead of an error. |
| Error code: | E996 0CA3 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting “COPIER > OPTION> FNC-SW> JM-ERR-D” to “0” (default), it is handled as a jam, instead of an error. |
| Error code: | E996 0CA4 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting “COPIER > OPTION> FNC-SW> JM-ERR-D” to “0” (default), it is handled as a jam, instead of an error. |
| Error code: | E996 0CA5 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CA5 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996 0CA6 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CA6 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence |
| Error code: | E996 0CA7 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CA7 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence |
| Error code: | E996 0CA8 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CA8 jam was detected |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence |
| Error code: | E996 0CAE |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting “COPIER > OPTION> FNC-SW> JM-ERR-D” to “0” (default), it is handled as a jam, instead of an error. |
| Error code: | E996 0CAF |
| Description: | Error for collecting sequence jam log (Finisher) |
| Causes: | Error for collecting jam log (Finisher) |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting “COPIER > OPTION> FNC-SW> JM-ERR-D” to “0” (default), it is handled as a jam, instead of an error. |
| Error code: | E996 0CB0 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CB0 jam was detected |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996 0CB3 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CB3 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996 0CB4 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CB4 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996 0CB6 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CB6 jam was detected |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence |
| Error code: | E996 0CB8 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CB8 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996 0CF0 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CF0 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence |
| Error code: | E996 0CF3 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CF3 jam was detected |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence |
| Error code: | E996 0CF4 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CF4 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence |
| Error code: | E996 0CF5 |
| Description: | Error for collecting sequence jam log (Printer). Error for collecting jam log (Printer) Continuous 0CF5 jam was detected. |
| Remedy: | Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence |
Название
Canon C-EXV49Bk Тонер черный
Canon C-EXV49C Тонер голубой
Canon C-EXV49M Тонер пурпурный
Canon C-EXV49Y Тонер желтый
Canon Блок ремня переноса
Canon Блок проявки пурпурный
Canon Блок проявки голубой
Canon Блок проявки черный
