Canon imageRUNNER Advance C356P III
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
40000
Скорость печати
A4
35
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Цветность печати |
цветная |
Размещение |
настольный |
Число страниц в месяц |
40 000 |
Область применения |
малый офис |
Макс. формат |
A4 |
Тип устройства |
Принтер |
Технология печати |
лазерная |
Сканер |
|
Печать фотографий |
|
Факс |
|
Телефон |
|
Копир |
|
Принтер |
|
Макс, ширина отпечатка |
216 |
Время разогрева |
30 |
Количество цветов |
4 |
Система непрерывной подачи чернил |
|
Печать без полей |
|
Пигментные чернила |
|
Макс, длина отпечатка |
356 |
Двусторонняя печать |
|
Прямая печать |
|
Макс, разрешение для ч/б печати |
|
| По X | 1 200 |
| По Y | 1 200 |
Скорость ч/б печати |
|
| A4 | 35 |
Время выхода первого отпечатка |
|
| Цветн, | 6,9 |
| Ч/б | 5,1 |
Сканер |
|
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Слайд-адаптер |
|
Стандарт WIA |
|
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
23 000 |
Количество картриджей |
4 |
Ресурс цветного картриджа/тонера |
18 000 |
Печать на: |
|
| Фотобумаге |
|
| CD/DVD |
|
| Рулоне |
|
| Конвертах |
|
| Пленках |
|
| Матовой бумаге |
|
| Этикетках |
|
| Глянцевой бумаге |
|
| Карточках |
|
Плотность бумаги |
|
| Максимальная | 220 |
| Минимальная | 60 |
Факс |
|
Цветной |
|
PC Fax |
|
Телефон |
|
АОН |
|
Стандарт DECT |
|
Беспроводная трубка |
|
Проводная трубка |
|
Шрифты и языки управления |
|
Языки управления |
|
| PostScript 2 |
|
| PostScript 3 |
|
|
|
|
| PCL 6 |
|
| PostScript |
|
Количество установленных шрифтов |
|
| PCL | 83 |
| PostScript | 136 |
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Максимальная | 2 300 |
| Стандартная | 650 |
Вывод бумаги |
|
| Стандартный | 250 |
| Максимальный | 500 |
Финишер |
|
Брошюровщик |
|
Сортер |
|
Степлер |
|
Интерфейсы |
|
Версия USB |
2,0 |
Устройство для чтения карт памяти |
|
Поддержка iOS |
|
Веб-интерфейс |
|
Wi-Fi 802.11n |
|
AirPrint |
|
Память/Процессор |
|
Объем памяти |
3 072 |
Емкость жесткого диска |
250 |
Частота процессора |
1 750 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Диагональ дисплея |
10,1 |
Экран |
|
Поддержка ОС |
|
| Mac OS |
|
| Windows |
|
| DOS |
|
Потребляемая мощность |
|
| В режиме ожидания | 40,3 |
| При работе | 488,5 |
Уровень шума |
|
| При работе | 53 |
Габариты |
|
Вес |
42 |
Глубина |
651 |
Ширина |
511 |
Высота |
541 |
Модули
MAIN DRIVE ASSEMBLY
FAX ASSEMBLY (FAX model)
FIXING ASSEMBLY, FX-201 (230V)
INTERNAL COMPONENTS 4
MULTI FEED TRAY ASSEMBLY
POWER SUPPLY ASSEMBLY (100V, 120V)
HOPPER ASSEMBLY
MACHINE REAR PLATE 1 (120V)
CONTROL PANEL ASSEMBLY US, CA, LTN, AU, SG, HK, IN
INTERNAL COMPONENTS 1
MACHINE REAR PLATE 2 (Single pass ADF)
107B INTERNAL COMPONENTS 5 (120V)
EXTERNAL COVERS, PANELS, ETC. C256iF
310 RESIST/PAPER PICK-UP ASS Y
Auto Document Feeder Assembly Set (Single Pass ADF)
CONTROLLER BOX ASSEMBLY (C256, C256i, 0256IF)
BOTTLE DRIVE ASSEMBLY
INTERNAL COMPONENTS 5 (230V)
MULTI FEED PAPER PICK-UP ASSY
PAPER PICK-UP COVER ASSY (Single pass ADF)
READER/ADF ASSEMBLY (Single pass ADF)
BOTTLE MOUNT ASSEMBLY
READER ASSEMBLY (Single pass ADF)
FIXING DRIVE ASSEMBLY
DC CONTROLLER PCB ASSEMBLY
PAPER PICK-UP DRIVE ASSEMBLY
CONTAINER, WASTE TONER, WT-201
POWER SUPPLY FAN ASSEMBLY
INTERNAL COVER ASSEMBLY
Auto Document Feeder Assembly Set (Single Pass ADF) 2
CASSETTE
PICK-UP LIFTER DRIVE ASSY
SPEAKER (FAX model)
MACHINE REAR PLATE 1 (230V)
CONTROLLER BOX ASSEMBLY (C356i, C356F, C356iF)
Auto Document Feeder Assembly Set (Single Pass ADF) 3
DOOR ASSEMBLY, RIGHT 2
INTERNAL COMPONENTS 3 (Single pass ADF)
DELIVERY COOLING FAN ASSEMBLY
DOOR ASSEMBLY, FRONT
CARTRIDGE AIR INTAKE FAN ASSY
Duplexing Guide Assembly
POWER SUPPLY ASSEMBLY (230V)
ADF MAINTENANCE KIT (Single pass ADF)
INTER. TRANSFER BELT ASS Y
810B FIXING ASSEMBLY, FX-201 (120V)
LASER SCANNER ASSEMBLY
INTERNAL COMPONENTS 2
EXTERNAL COVERS, PANELS, ETC. C356iF
PAPER DELIVERY/REVERSE ASS Y
DOOR ASSEMBLY, RIGHT
Детали PAPER PICK-UP COVER ASSY (Single pass ADF)
| Деталь: | MOTOR, DC |
| Парткод: | FL0-1543-000 |
| Деталь: | MOTOR, DC |
| Парткод: | FL0-1544-000 |
| Деталь: | MAIN DRIVE ASSEMBLY |
| Парткод: | FM0-0040-020 |
| Деталь: | CABLE, FAX SIGNAL |
| Парткод: | FM1-W903-000 |
| Деталь: | CABLE, 1 CIRCUIT MODULAR |
| Парткод: | FM1-W905-000 |
| Деталь: | CABLE, FAX POWER |
| Парткод: | FM1-W904-000 |
| Деталь: | CABLE, SPEAKER |
| Парткод: | FM1-W906-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | SPACER,MODULAR |
| Парткод: | WT8-5076-000 |
| Деталь: | MODULAR PCB ASSEMBLY |
| Парткод: | FM4-2476-000 |
| Деталь: | 1 LINE PCB ASSEMBLY |
| Парткод: | FM1-W902-000 |
| Деталь: | FAX ASSEMBLY |
| Парткод: | NPN |
| Деталь: | PRESSURE ROLLER KIT |
| Парткод: | FM1-K198-010 |
| Деталь: | HOLDER, BEARING |
| Парткод: | FC0-6079-000 |
| Деталь: | CAM,PRESSURE RELEASE |
| Парткод: | FC0-6086-000 |
| Деталь: | PLATE, PRESSURE, REAR |
| Парткод: | FC0-6088-000 |
| Деталь: | FLAG, PAPER DELIVERY SENSOR |
| Парткод: | FC0-6092-010 |
| Деталь: | PLATE, PRESSURE, LEFT |
| Парткод: | FC0-6131-000 |
| Деталь: | LOCK, SHUTTER, FRONT |
| Парткод: | FC0-6156-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC0-6157-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM1-R730-000 |
| Деталь: | CABLE, FIXING ASSEMBLY |
| Парткод: | FM1-A802-000 |
| Деталь: | GUIDE, FIXING ENTRANCE |
| Парткод: | FC0-6089-010 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0230-000 |
| Деталь: | GEAR, 29T |
| Парткод: | FU9-0610-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU9-0611-000 |
| Деталь: | GEAR, 30T |
| Парткод: | FU9-0612-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2104-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2105-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2106-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2111-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | IC,PHOTO-INTERRUPTER,LG248NL1A |
| Парткод: | WG8-5783-000 |
| Деталь: | BEARING, BALL, L-1260ZZR |
| Парткод: | XG9-0865-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-006 |
| Деталь: | DAMPER |
| Парткод: | FL0-6873-000 |
| Деталь: | FIXING ASSEMBLY, FX-201 |
| Парткод: | FM1-R727-010 |
| Деталь: | GUIDE, SWING |
| Парткод: | FC0-7048-000 |
| Деталь: | GUIDE, STOPPER, RIGHT DOOR |
| Парткод: | FC0-5942-000 |
| Деталь: | HINGE, EXTERNAL, FRONT |
| Парткод: | FM1-C348-000 |
| Деталь: | LEVER, STOPPER, RIGHT |
| Парткод: | FC0-5912-000 |
| Деталь: | COVER, DOOR CONNECTOR, RIGHT |
| Парткод: | FE3-9076-000 |
| Деталь: | HINGE, OUTER COVER, REAR |
| Парткод: | FC0-5929-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | BASE, HOOK, RIGHT |
| Парткод: | FC0-5918-000 |
| Деталь: | TRAY, REVERSE |
| Парткод: | FE3-8409-000 |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | TRAY, MULTI FEED EXTENSION |
| Парткод: | FE3-9099-000 |
| Деталь: | PLATE, PAPER SIDE END, FRONT |
| Парткод: | FE3-9101-000 |
| Деталь: | PLATE, PAPER SIDE END, REAR |
| Парткод: | FE3-9100-000 |
| Деталь: | HOOK, MULTI FEED TRAY |
| Парткод: | FE3-5650-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-5651-000 |
| Деталь: | CAP, MULTI FEED EXTENSION TRAY |
| Парткод: | FE4-5352-000 |
| Деталь: | SHEET, SEPARATION |
| Парткод: | FL3-6526-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0582-000 |
| Деталь: | PINION, SIDE END |
| Парткод: | FU9-0692-000 |
| Деталь: | LABEL, MULTI FEED SIZE |
| Парткод: | FE4-1826-000 |
| Деталь: | LABEL, MULTI PICK-UP FULL |
| Парткод: | FE4-1823-010 |
| Деталь: | MULTI FEED TRAY ASSEMBLY |
| Парткод: | FM1-D706-000 |
| Деталь: | POWER SUPPLY ASSEMBLY |
| Парткод: | FM1-L543-000 |
| Деталь: | HOPPER ASSEMBLY |
| Парткод: | FM0-0006-010 |
| Деталь: | H.V. CONTACT ASSEMBLY, COLOR |
| Парткод: | FM0-0043-000 |
| Деталь: | 1ST TRANS. H.V. CONTACT ASSY |
| Парткод: | FM4-9961-000 |
| Деталь: | PROCESS CONTROL PCB ASSY |
| Парткод: | FM4-9908-010 |
| Деталь: | CONTACT, 1ST TRANSFER H.V., 1 |
| Парткод: | FM0-0038-000 |
| Деталь: | I.T.B. RELEASE SWITCH ASSEMBLY |
| Парткод: | FM0-0039-010 |
| Деталь: | H.V. CONTACT ASSEMBLY, BLACK |
| Парткод: | FM0-0042-010 |
| Деталь: | 2ND TRANS. H.V. CONTACT ASSY |
| Парткод: | FM0-0079-000 |
| Деталь: | HEATER SWITCH ASSEMBLY |
| Парткод: | FM0-0083-000 |
| Деталь: | CASSETTE AUTO CLOSE ASSEMBLY |
| Парткод: | FM0-0017-020 |
| Деталь: | SENSOR, HUMIDITY |
| Парткод: | WP2-5410-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | CABLE, CASSETTE ASSY |
| Парткод: | FM1-A843-000 |
| Деталь: | 2ND TRANSFER H.V. PCB ASSEMBLY |
| Парткод: | FM1-R266-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7440-002 |
| Деталь: | HOLDER, REAR CASSETTE BOSS |
| Парткод: | FE4-8559-000 |
| Деталь: | MACHINE REAR PLATE 1 |
| Парткод: | NPN |
| Деталь: | COVER, REAR |
| Парткод: | FE4-9433-000 |
| Деталь: | COVER, FRAME |
| Парткод: | FE4-1774-010 |
| Деталь: | GUIDE, LAMP LED |
| Парткод: | FE4-1787-000 |
| Деталь: | KEY TOP, SIDE |
| Парткод: | FE4-1788-000 |
| Деталь: | KEY TOP, VOLUME |
| Парткод: | FE4-1789-000 |
| Деталь: | FLAT CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-N429-000 |
| Деталь: | KEY TOP, STOP |
| Парткод: | FE4-5109-000 |
| Деталь: | KEY TOP, RESET |
| Парткод: | FE4-5110-000 |
| Деталь: | KEY TOP, SLEEP |
| Парткод: | FE4-5111-000 |
| Деталь: | KEY TOP, NUMBERS |
| Парткод: | FL1-2178-000 |
| Деталь: | KEY TOP, SETTINGS/REGISTRATION |
| Парткод: | FE4-5556-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | FK4-2360-000 |
| Деталь: | SPEAKER |
| Парткод: | FK4-2365-000 |
| Деталь: | KEY TOP, START |
| Парткод: | FL0-5116-000 |
| Деталь: | LCD HOLDER UNIT |
| Парткод: | FM1-N440-000 |
| Деталь: | CPU PCB ASSEMBLY |
| Парткод: | FM1-X811-000 |
| Деталь: | KEY TOP PCB ASSEMBLY |
| Парткод: | FM1-M929-000 |
| Деталь: | CABLE, 10 KEY |
| Парткод: | FM1-X899-010 |
| Деталь: | COVER, SLIDE |
| Парткод: | FE4-9100-000 |
| Деталь: | PLATE, JOINT, LOWER |
| Парткод: | FE8-3528-000 |
| Деталь: | PLATE, JOINT, UPPER |
| Парткод: | FE8-3529-000 |
| Деталь: | SHEET |
| Парткод: | FL0-7203-000 |
| Деталь: | HINGE, CONTROL ASSEMBLY, LEFT |
| Парткод: | FM1-L557-000 |
| Деталь: | HINGE, CONTROL ASSEMBLY, RIGHT |
| Парткод: | FM1-N366-000 |
| Деталь: | SHEET |
| Парткод: | FL1-1429-000 |
| Деталь: | CONTROL PANEL SLIDE UNIT |
| Парткод: | FM1-P215-010 |
| Деталь: | SPACER, SLIDE |
| Парткод: | FE8-2023-000 |
| Деталь: | RAIL, CONTROL PANEL |
| Парткод: | FE8-3522-000 |
| Деталь: | CABLE, SCULD USS |
| Парткод: | FM1-W897-000 |
| Деталь: | SHEET, PROTECTION |
| Парткод: | FL1-3484-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1632-000 |
| Деталь: | SCREW, STEPPED, M4 |
| Парткод: | FU2-1943-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | NPN |
| Деталь: | COVER, INNER, FRONT, RIGHT |
| Парткод: | FM1-L556-000 |
| Деталь: | COVER, MAIN SWITCH |
| Парткод: | FC0-7172-000 |
| Деталь: | SWITCH |
| Парткод: | WC2-5803-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU7-2778-000 |
| Деталь: | LEVER, TOGGLE |
| Парткод: | FE2-2086-000 |
| Деталь: | LABEL, TONER TYPE |
| Парткод: | FE8-8494-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | REGISTRATION DRIVE ASSY |
| Парткод: | FM1-A225-010 |
| Деталь: | WASTE TONER SENSOR PCB ASSY |
| Парткод: | FM1-C981 -000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FU2-0577-000 |
| Деталь: | TONER INTER. EJECT ASSY |
| Парткод: | FM0-0037-000 |
| Деталь: | ARM, BOTTLE LOCK |
| Парткод: | FC0-5801-000 |
| Деталь: | CABLE, UI |
| Парткод: | FM1-Y912-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, 6P, W |
| Парткод: | VS1-8959-006 |
| Деталь: | CONNECTOR, NEW BOTTLE DET., BK |
| Парткод: | FM0-0065-000 |
| Деталь: | CONNECTOR, NEW BOTTLE DET., CL |
| Парткод: | FM0-0075-000 |
| Деталь: | LABEL, PAPER SIZE |
| Парткод: | FE8-2569-000 |
| Деталь: | SHEET, SEPARATION |
| Парткод: | FL3-6526-000 |
| Деталь: | LABEL, MOUNTING INSTRUCTION |
| Парткод: | FE3-9943-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7440-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | PLATE, LIFTING |
| Парткод: | FL0-3261 -000 |
| Деталь: | BUSHING |
| Парткод: | FE4-1123-000 |
| Деталь: | PLATE, USB |
| Парткод: | FC0-7486-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK4-3820-000 |
| Деталь: | COVER, FRONT INNER, UPPER |
| Парткод: | FC0-7020-000 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | INTERLOCKASSEMBLY |
| Парткод: | FM0-0044-000 |
| Деталь: | SWITCH ASSEMBLY, RIGHT |
| Парткод: | FM0-0046-000 |
| Деталь: | CABLE, BOTTLE |
| Парткод: | FM1-C857-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | CABLE, PRIMARY TRANSFER H.V. |
| Парткод: | FM1-A832-000 |
| Деталь: | CABLE, MAIN |
| Парткод: | FM1-V956-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CABLE, BOTTLE SENSOR, Y/C |
| Парткод: | FM1-A855-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BL |
| Парткод: | VS1-8412-017 |
| Деталь: | CABLE, FIXING DRIVE |
| Парткод: | FM1-A853-000 |
| Деталь: | CABLE, POWER SUPPLY |
| Парткод: | FM1-V954-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | CABLE, ENVIRONMENT SENSOR |
| Парткод: | FM1-A820-000 |
| Деталь: | CABLE, BOTTLE SENSOR, M/K |
| Парткод: | FM1-A854-000 |
| Деталь: | CABLE, FINISHER |
| Парткод: | FM1-A821 -000 |
| Деталь: | ALL NIGHT POWER PCB ASSEMBLY |
| Парткод: | FK3-3274-000 |
| Деталь: | CABLE, POWER SUPPLY, AC |
| Парткод: | FM1-V957-000 |
| Деталь: | MACHINE REAR PLATE 2 |
| Парткод: | NPN |
| Деталь: | 1ST TRANSFER H.V. PCB ASSEMBLY |
| Парткод: | FM0-0050-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-3643-010 |
| Деталь: | CABLE, REG. MOTOR WASTE TONER |
| Парткод: | FM1-A836-000 |
| Деталь: | CABLE, CASSETTE HEATER |
| Парткод: | FM1-A811 -000 |
| Деталь: | CAP, CONNECTOR |
| Парткод: | FE3-4477-000 |
| Деталь: | FOOT, RUBBER |
| Парткод: | FM1-B574-000 |
| Деталь: | CASSETTE STOPPER ASSEMBLY |
| Парткод: | FM1-B298-000 |
| Деталь: | OPTION CST. DRAWER ASSEMBLY |
| Парткод: | FM1-C323-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | INTERNAL COMPONENTS 5 |
| Парткод: | NPN |
| Деталь: | COVER, CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-L540-000 |
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FM1-L554-000 |
| Деталь: | COVER, UPPER |
| Парткод: | FM1-L544-000 |
| Деталь: | COVER, REAR UPPER |
| Парткод: | FM1-D699-010 |
| Деталь: | COVER, RIGHT LOWER |
| Парткод: | FE3-9079-000 |
| Деталь: | COVER, ENV. HEATER SWITCH |
| Парткод: | FE3-9087-000 |
| Деталь: | COVER, REAR, 2 |
| Парткод: | FE4-9082-000 |
| Деталь: | SEAL |
| Парткод: | FC6-4513-000 |
| Деталь: | COVER, CONTROL HINGE, REAR |
| Парткод: | FE8-4215-000 |
| Деталь: | COVER, PAPER DELIVERY |
| Парткод: | FE8-4216-000 |
| Деталь: | COVER, RIGHT FRONT |
| Парткод: | FL0-2604-000 |
| Деталь: | COVER, RIGHT REAR |
| Парткод: | FL0-2606-000 |
| Деталь: | COVER, RIGHT UPPER |
| Парткод: | FL0-2605-000 |
| Деталь: | SHEET, PAPER DELIVERY TRAY, 2 |
| Парткод: | FL0-1008-000 |
| Деталь: | COVER,LEFT UPPER |
| Парткод: | FE8-4211-000 |
| Деталь: | COVER, DEVICE PORT |
| Парткод: | FE3-9082-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FE3-9088-000 |
| Деталь: | COVER, LEFT LOWER |
| Парткод: | FL0-5332-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FE4-1818-000 |
| Деталь: | COVER,LOUVER |
| Парткод: | FE4-9079-000 |
| Деталь: | COVER, REAR, 1 |
| Парткод: | FE4-9078-000 |
| Деталь: | COVER, HEATER, ENVIRONMENT |
| Парткод: | FE3-9089-000 |
| Деталь: | LABEL, FAX |
| Парткод: | FE8-4239-000 |
| Деталь: | COVER, LOUVER, 1 |
| Парткод: | FE4-9095-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FE4-3758-000 |
| Деталь: | SHEET, PAPER DELIVERY TRAY |
| Парткод: | FL0-1007-000 |
| Деталь: | COVER, CONTROL PANEL CABLE |
| Парткод: | FE4-9431-000 |
| Деталь: | DAMPER UNIT, AIR |
| Парткод: | FC7-6142-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5888-000 |
| Деталь: | CABLE, REG. GROUNDING |
| Парткод: | FC0-6968-000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FC0-6979-000 |
| Деталь: | BLOCK, REGIST. PRESSURE |
| Парткод: | FC0-7174-000 |
| Деталь: | LEVER, PAPER PICK-UP SENSOR |
| Парткод: | FC0-7204-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC0-7205-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC0-7211-000 |
| Деталь: | FLAG, REGISTRATION SENSOR |
| Парткод: | FC0-7218-000 |
| Деталь: | LEVER, PAPER DETECT |
| Парткод: | FC0-7670-000 |
| Деталь: | BUSHING |
| Парткод: | FC9-9146-000 |
| Деталь: | LEVER, PAPER PICK-UP LATCH |
| Парткод: | FE8-9951-000 |
| Деталь: | ARM, PAPER PICK-UP |
| Парткод: | FE3-1602-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-1617-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-1618-000 |
| Деталь: | ROLLER, REGISTRATION DRIVEN |
| Парткод: | FE3-9592-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FE3-4860-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FE3-4861-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-5614-000 |
| Деталь: | GUIDE, PRE-REGISTRATION |
| Парткод: | FE3-6112-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-6113-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-6114-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-6119-000 |
| Деталь: | ROLLER, EXTRACTION |
| Парткод: | FL1-1869-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-2885-000 |
| Деталь: | ONE-WAY GEAR ASSEMBLY |
| Парткод: | FL0-1570-000 |
| Деталь: | SHEET, SEPARATION ROLLER GUIDE |
| Парткод: | FL0-2588-000 |
| Деталь: | ONE-WAY GEAR ASSEMBLY |
| Парткод: | FM0-0030-000 |
| Деталь: | REG. SWING HOLDER ASSEMBLY |
| Парткод: | FM1-B297-000 |
| Деталь: | SEPARATION FRAME ASSEMBLY |
| Парткод: | FM1-B557-000 |
| Деталь: | BUSHING |
| Парткод: | FS1-1205-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-0234-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-4002-000 |
| Цена: | 4 900 ₽ |
| Деталь: | GEAR, 22T |
| Парткод: | FU2-0248-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0284-000 |
| Деталь: | GEAR, 32T |
| Парткод: | FU2-0287-000 |
| Деталь: | GEAR, 27T/21T |
| Парткод: | FU2-0294-000 |
| Деталь: | GEAR, 17T |
| Парткод: | FU2-0295-010 |
| Деталь: | GEAR, 24T/20T |
| Парткод: | FU2-0297-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-0298-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-0578-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0085-000 |
| Деталь: | GEAR, 17T |
| Парткод: | FU9-0675-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2094-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | ROLLER, REGISTRATION DRIVEN |
| Парткод: | FE3-9593-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1674-000 |
| Цена: | 5 000 ₽ |
| Деталь: | ONE-WAY CLUTCH ASSEMBLY |
| Парткод: | FL0-1515-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-0236-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-3935-000 |
| Деталь: | RING, RESIN, RETAINING |
| Парткод: | FC6-3002-000 |
| Деталь: | SHEET, GAP |
| Парткод: | FL0-5214-000 |
| Деталь: | RESIST/PAPER PICK-UP ASSY |
| Парткод: | FM0-0029-000 |
| Деталь: | CLIP |
| Парткод: | FC0-1271-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CLIP |
| Парткод: | FC5-4424-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6316-010 |
| Деталь: | COVER, REAR |
| Парткод: | FE4-5751-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FE4-5701-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE4-5712-000 |
| Деталь: | COVER, CARD READER |
| Парткод: | FE4-5735-000 |
| Деталь: | GUIDE, CABLE, FRONT |
| Парткод: | FE4-5746-000 |
| Деталь: | ARM, JOINT |
| Парткод: | FE4-5761-000 |
| Деталь: | LABEL |
| Парткод: | FE4-5779-000 |
| Деталь: | DOUBLE FEED DETECTION KIT |
| Парткод: | FM1-K086-010 |
| Деталь: | STOPPER, CLUTCH ROTATION |
| Парткод: | FE4-5788-000 |
| Деталь: | FRAME, BASE |
| Парткод: | FE4-5790-000 |
| Деталь: | LEVER, DRIVE RELEASE |
| Парткод: | FE4-5796-000 |
| Деталь: | HINGE, ADF, LEFT |
| Парткод: | FE8-2341-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE8-1580-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FE8-1582-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1586-000 |
| Деталь: | HINGE, ADF, RIGHT |
| Парткод: | FE8-2342-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1590-000 |
| Деталь: | HOLDER, DOUBLE FEED DETECTION |
| Парткод: | FE8-1865-000 |
| Деталь: | HOLDER, LED |
| Парткод: | FE8-1882-000 |
| Деталь: | COVER, LED |
| Парткод: | FE8-1883-000 |
| Деталь: | HOLDER, PAPER DELIVERY SENSOR |
| Парткод: | FE8-1884-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1890-000 |
| Деталь: | DOCUMENT TRAY ASSEMBLY |
| Парткод: | FM1-L783-000 |
| Деталь: | COUPLING |
| Парткод: | FE8-2329-000 |
| Деталь: | COUPLING |
| Парткод: | FE8-2330-000 |
| Деталь: | ROLLER, TENSIONER |
| Парткод: | FE8-2332-000 |
| Деталь: | GUIDE, CABLE, REAR |
| Парткод: | FE8-2333-000 |
| Деталь: | GUIDE, CABLE, LOWER |
| Парткод: | FE8-2334-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE8-2335-000 |
| Деталь: | COVER, CABLE |
| Парткод: | FE8-2338-000 |
| Деталь: | ROLLER, TENSIONER |
| Парткод: | FE8-2339-000 |
| Деталь: | COVER, USB |
| Парткод: | FE8-2355-000 |
| Деталь: | COVER,BOTTOM |
| Парткод: | FE8-2356-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE8-2419-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FE8-2426-000 |
| Деталь: | LEVER |
| Парткод: | FE8-2443-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-2623-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-2624-000 |
| Деталь: | DAMPER |
| Парткод: | FE8-3710-000 |
| Деталь: | PAD, PICK-UP |
| Парткод: | FE8-3713-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-3716-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FE8-3973-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FE8-6364-000 |
| Деталь: | FAN |
| Парткод: | FK2-0472-010 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-3805-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK4-3808-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK4-3995-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1428-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0289-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-5405-000 |
| Деталь: | ROLLER, READ, 1 |
| Парткод: | FL1-0267-000 |
| Деталь: | ROLLER, READ, 2 |
| Парткод: | FL1-0268-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FL1-0269-000 |
| Деталь: | CUSHION |
| Парткод: | FL0-5178-000 |
| Деталь: | GUIDE, PLATEN |
| Парткод: | FL1-0441 -000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FL1-0740-000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-1512-000 |
| Деталь: | GUIDE, SEPARATION |
| Парткод: | FL1-1513-000 |
| Деталь: | CONTACT IMAGE SENSOR ASSY SET |
| Парткод: | FM1-L777-010 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2057-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2174-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2175-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FL1-3412-000 |
| Деталь: | EJECT LIGHT LED PCB ASSY |
| Парткод: | FM0-0294-000 |
| Деталь: | LEAD 1 OUTER GUIDE ASSEMBLY |
| Парткод: | FM1-L785-010 |
| Деталь: | LEAD 2 OUTER GUIDE ASSEMBLY |
| Парткод: | FM1-L786-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-N521 -000 |
| Деталь: | CABLE, ADF MAIN |
| Парткод: | FM1-W888-000 |
| Деталь: | CABLE, DOUBLE FEED DETECTION |
| Парткод: | FM1-W889-000 |
| Деталь: | CABLE, ADF PASS SENSOR |
| Парткод: | FM1-W892-000 |
| Деталь: | MOTOR ASSY |
| Парткод: | FM1-W895-000 |
| Деталь: | PIN, SUS |
| Парткод: | XD9-0352-000 |
| Деталь: | BUSHING, PL |
| Парткод: | FS1-1528-000 |
| Деталь: | BUSHING |
| Парткод: | FS5-1805-000 |
| Деталь: | SCREW, STEPPED, M3 |
| Парткод: | FS5-9391-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-0595-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1417-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU2-1446-000 |
| Деталь: | SPRING, CLUTCH |
| Парткод: | FU2-1747-000 |
| Деталь: | GEAR, 38T |
| Парткод: | FU2-1749-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU2-1750-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU2-1751-000 |
| Деталь: | PULLEY, 18T |
| Парткод: | FU2-1752-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1754-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-1756-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1757-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1758-000 |
| Деталь: | PULLEY, 23T |
| Парткод: | FU2-1759-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1831-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU5-3643-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1572-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | PULLEY |
| Парткод: | FU8-0240-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0333-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1606-940 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-640 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1609-560 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1610-640 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-2003-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE8-2385-000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FE8-3531-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0290-000 |
| Деталь: | COVER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2056-000 |
| Деталь: | ROLLER, PAPER FEED, 1 |
| Парткод: | FC5-4286-000 |
| Деталь: | WEIGHT |
| Парткод: | FE4-5786-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FL0-5407-000 |
| Деталь: | SCREW,M3X4 |
| Парткод: | XA9-0624-000 |
| Деталь: | AUTO DOCUMENT FEEDER ASSY SET |
| Парткод: | FM1-L778-010 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-R757-000 |
| Деталь: | SCREW, MACH. PAN HEAD, M3X4 |
| Парткод: | XA9-1979-000 |
| Деталь: | TPM PCB ASSEMBLY |
| Парткод: | FM1-M981-000 |
| Деталь: | CABLE, SATA POWER |
| Парткод: | FK4-3811-000 |
| Деталь: | CABLE, SATA SIGNAL |
| Парткод: | FK4-3810-000 |
| Деталь: | HARD DISK DRIVE, MQ01ABF032 |
| Парткод: | FK4-1550-000 |
| Деталь: | LABEL, CAUTION |
| Парткод: | FU8-8257-000 |
| Деталь: | DAMPER, CUSHION |
| Парткод: | XH9-0149-000 |
| Деталь: | SPACER |
| Парткод: | XZ1-1301-005 |
| Деталь: | IC, STANDARD SELL, MB8AA4600PB |
| Парткод: | FK3-3872-000 |
| Деталь: | IC, 88E8075-B0-NNC2C000-W553, |
| Парткод: | FK4-1861-000 |
| Деталь: | IC, R9A06G011GBG, MPU |
| Парткод: | FK4-2216-000 |
| Деталь: | IC, MB8AL1070MP-GE1, ASIC |
| Парткод: | FK4-1649-000 |
| Деталь: | CONTROLLER BOX ASSEMBLY |
| Парткод: | NPN |
| Деталь: | BOTTLE DRIVE ASSEMBLY |
| Парткод: | FM0-0007-000 |
| Деталь: | 1ST TRANSFER H.V. PCB ASSEMBLY |
| Парткод: | FM0-0050-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-3643-010 |
| Деталь: | CABLE, REG. MOTOR WASTE TONER |
| Парткод: | FM1-A836-000 |
| Деталь: | CABLE, CASSETTE HEATER |
| Парткод: | FM1-A812-000 |
| Деталь: | CAP, CONNECTOR |
| Парткод: | FE3-4477-000 |
| Деталь: | FOOT, RUBBER |
| Парткод: | FM1-B574-000 |
| Деталь: | CASSETTE STOPPER ASSEMBLY |
| Парткод: | FM1-B298-000 |
| Деталь: | OPTION CST. DRAWER ASSEMBLY |
| Парткод: | FM1-C323-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | INTERNAL COMPONENTS 5 |
| Парткод: | NPN |
| Деталь: | HOLDER, PAPER FEED ROLLER |
| Парткод: | FC0-6637-000 |
| Деталь: | LINK, RELEASE |
| Парткод: | FE8-2635-000 |
| Деталь: | SHAFT, ROLLER |
| Парткод: | FE3-0387-000 |
| Деталь: | LEVER, PAPER YES/NO SENSING |
| Парткод: | FE3-1642-000 |
| Деталь: | CAM, ROLLER ESTRANGEMENT |
| Парткод: | FE3-3589-010 |
| Деталь: | GEAR, 33T |
| Парткод: | FU6-1304-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2088-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2091-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FE3-4860-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1674-000 |
| Цена: | 5 000 ₽ |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1600-000 |
| Деталь: | MULTI FEED PAPER PICK-UP ASSY |
| Парткод: | FM1-B308-010 |
| Деталь: | LEVER, STOP |
| Парткод: | FC6-8971-010 |
| Деталь: | ADF PAPER PICK-UP ASSEMBLY |
| Парткод: | FM1-L782-000 |
| Деталь: | COVER, LED |
| Парткод: | FL1-0424-000 |
| Деталь: | COVER, PAPER PICK-UP |
| Парткод: | FL1-0427-000 |
| Деталь: | BUSHING |
| Парткод: | FE8-3706-000 |
| Деталь: | LEVER |
| Парткод: | FE8-3708-000 |
| Деталь: | SPRING, LEAF |
| Парткод: | FE8-3709-000 |
| Деталь: | LABEL, BLUE |
| Парткод: | FE8-3717-000 |
| Деталь: | SHUTTER |
| Парткод: | FL2-9948-000 |
| Деталь: | JOINT |
| Парткод: | FC8-6353-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC8-6355-000 |
| Цена: | 700 ₽ |
| Деталь: | BUSHING |
| Парткод: | FE8-3707-000 |
| Деталь: | ROLLER, PAPER FEED |
| Парткод: | FL0-1431 -000 |
| Деталь: | SPRING |
| Парткод: | FU2-1834-000 |
| Деталь: | GEAR, 20T |
| Парткод: | FU8-0299-000 |
| Деталь: | GEAR, 22T |
| Парткод: | FU8-0300-000 |
| Деталь: | GEAR, 33T |
| Парткод: | FU8-0301-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0333-000 |
| Деталь: | ROLLER, REGISTRATION, 2 |
| Парткод: | FC5-4324-000 |
| Деталь: | ROLLER, BELT |
| Парткод: | FC8-7343-000 |
| Деталь: | LEVER, PICK RELEASE |
| Парткод: | FE8-1867-000 |
| Деталь: | GUIDE, GROUNDING |
| Парткод: | FE8-1868-000 |
| Деталь: | HOLDER, REGISTRATION ROLLER |
| Парткод: | FE8-1869-000 |
| Деталь: | LATCH |
| Парткод: | FE8-1870-000 |
| Деталь: | LINK, OPEN/CLOSE |
| Парткод: | FE8-1874-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE8-2118-000 |
| Деталь: | GUIDE, LED |
| Парткод: | FE8-2120-000 |
| Деталь: | GUIDE, PAPER PICK-UP, LOWER |
| Парткод: | FE8-2130-000 |
| Деталь: | HOLDER, PICK |
| Парткод: | FE8-2386-000 |
| Деталь: | FLAG,SENSOR |
| Парткод: | FE8-2387-000 |
| Деталь: | COUPLING |
| Парткод: | FE8-2455-000 |
| Деталь: | PHOTO-SENSOR, KUA0055C |
| Парткод: | FK2-6470-000 |
| Деталь: | ARM, OPEN/CLOSE COVER, FRONT |
| Парткод: | FL1-0526-000 |
| Деталь: | ARM, OPEN/CLOSE COVER, REAR |
| Парткод: | FL1-0527-000 |
| Деталь: | LED PCB ASSEMBLY |
| Парткод: | FM1-K827-000 |
| Деталь: | CABLE, COVER |
| Парткод: | FM1-W890-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7177-013 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1806-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1808-000 |
| Деталь: | GEAR, 29T |
| Парткод: | FU2-1833-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1807-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1572-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-2003-000 |
| Деталь: | SHEET |
| Парткод: | FC8-5908-000 |
| Деталь: | PIN SUS |
| Парткод: | XD9-0352-000 |
| Деталь: | PAPER PICK-UP COVER ASSY |
| Парткод: | NPN |
| Деталь: | COVER, READER REAR, 2 |
| Парткод: | FE8-2109-000 |
| Деталь: | CLAMP, READER SHAFT, RIGHT |
| Парткод: | FE3-8375-000 |
| Деталь: | COVER, COPYBOARD |
| Парткод: | FL1-0407-000 |
| Деталь: | HINGE, READER |
| Парткод: | FE8-2110-000 |
| Деталь: | SHAFT, READER HINGE |
| Парткод: | FE8-2405-000 |
| Деталь: | COVER, CABLE |
| Парткод: | FE8-2099-010 |
| Деталь: | READER LINK ASSEMBLY |
| Парткод: | FM4-9850-000 |
| Деталь: | LABEL, DOCUMENT DIRECTION |
| Парткод: | FE8-4575-000 |
| Деталь: | LABEL,CLEANING/PROHIBITION |
| Парткод: | FE8-4578-000 |
| Деталь: | READER/ADF ASSEMBLY |
| Парткод: | NPN |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | BOTTLE MOUNT ASSEMBLY |
| Парткод: | FM0-0002-010 |
| Деталь: | RING, C,EXTERNAL |
| Парткод: | FE3-7699-000 |
| Деталь: | LABEL, BLACK LINE, CLEANING |
| Парткод: | FE8-4582-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE8-6152-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FE8-6153-000 |
| Деталь: | COVER, READER REAR, UP. |
| Парткод: | FE8-2093-000 |
| Деталь: | HOLDER, OPEN/CLOSE SENSOR |
| Парткод: | FE8-2094-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE8-2011-000 |
| Деталь: | COVER, MOTOR |
| Парткод: | FE8-2009-000 |
| Деталь: | STOPPER, BELT |
| Парткод: | FC0-5550-000 |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | FE8-2361-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FE8-2003-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FE8-4730-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FE8-4731 -000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-1521-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5557-000 |
| Деталь: | COVER, READER REAR, 1 |
| Парткод: | FE8-2098-000 |
| Деталь: | PULLEY, IDLER |
| Парткод: | FC0-5650-000 |
| Деталь: | FLAG,SENSOR |
| Парткод: | FE8-2095-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | HOLDER, PULLEY, IDLER |
| Парткод: | FC0-5552-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK3-3035-000 |
| Деталь: | CONTACT IMAGE SENSOR ASSEMBLY |
| Парткод: | FM1-L776-010 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-3804-000 |
| Деталь: | COVER |
| Парткод: | FE8-2097-000 |
| Деталь: | CABLE, READER |
| Парткод: | FM1-W894-000 |
| Деталь: | CABLE, HOME POSITION SENSOR |
| Парткод: | FM1-C987-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE8-2096-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK4-3807-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FL1-0411 -000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU6-2873-000 |
| Деталь: | GEAR, 85T/20T |
| Парткод: | FU9-0581-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1817-000 |
| Деталь: | MOUNT, SENSOR |
| Парткод: | FL1-0415-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | READER COVER UNIT, TOP |
| Парткод: | FM1-M039-000 |
| Деталь: | WIRELESS NETWORK PCB ASSEMBLY |
| Парткод: | FM1-N784-000 |
| Деталь: | INTERFACE SENSOR PCB ASSEMBLY |
| Парткод: | FM1-W896-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1818-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, 6P, W |
| Парткод: | VS1-8959-006 |
| Деталь: | READER ASSEMBLY |
| Парткод: | NPN |
| Деталь: | MOTOR, DC |
| Парткод: | FK4-0638-000 |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK4-0641-000 |
| Деталь: | FIXING DRIVE ASSEMBLY |
| Парткод: | FM0-0071-000 |
| Деталь: | FIXING DRIVE ASSEMBLY |
| Парткод: | NPN |
| Деталь: | DC CONTROLLER PCB ASSEMBLY |
| Парткод: | FM2-A889-000 |
| Деталь: | CABLE, DDIP |
| Парткод: | FM1-V958-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | WE8-6933-000 |
| Деталь: | IC, ASIC, T6VN7EFG-0002 |
| Парткод: | FK3-2323-000 |
| Деталь: | DC CONTROLLER PCB ASSEMBLY |
| Парткод: | NPN |
| Деталь: | MOTOR, STEPPING |
| Парткод: | FK4-0640-000 |
| Деталь: | PAPER PICK-UP DRIVE ASSEMBLY |
| Парткод: | FM1-A226-000 |
| Деталь: | FLAG, WASTE TONER SCREW |
| Парткод: | FC0-5969-000 |
| Деталь: | CAP, WASTE TONER CONTAINER |
| Парткод: | FC0-5971-000 |
| Деталь: | WASTE TONER FULL DETECT ASSY |
| Парткод: | FC0-6985-010 |
| Деталь: | CONTAINER, WASTE TONER, WT-201 |
| Парткод: | FM0-0015-010 |
| Деталь: | FAN |
| Парткод: | FK4-0636-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | POWER SUPPLY FAN ASSEMBLY |
| Парткод: | NPN |
| Деталь: | ARM,SENSOR |
| Парткод: | FC0-5972-000 |
| Деталь: | BLOCK, WASTE TONER |
| Парткод: | FC0-7589-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0574-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2027-000 |
| Деталь: | INTERNAL COVER ASSEMBLY |
| Парткод: | NPN |
| Деталь: | CLIP |
| Парткод: | FC0-1271-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CLIP |
| Парткод: | FC5-4424-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6316-010 |
| Деталь: | COVER, REAR |
| Парткод: | FE4-5751-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FE4-5701-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE4-5712-000 |
| Деталь: | COVER, CARD READER |
| Парткод: | FE4-5735-000 |
| Деталь: | GUIDE, CABLE, FRONT |
| Парткод: | FE4-5746-000 |
| Деталь: | ARM, JOINT |
| Парткод: | FE4-5761-000 |
| Деталь: | LABEL |
| Парткод: | FE4-5779-000 |
| Деталь: | DOUBLE FEED DETECTION KIT |
| Парткод: | FM1-K086-010 |
| Деталь: | STOPPER, CLUTCH ROTATION |
| Парткод: | FE4-5788-000 |
| Деталь: | FRAME, BASE |
| Парткод: | FE4-5790-000 |
| Деталь: | LEVER, DRIVE RELEASE |
| Парткод: | FE4-5796-000 |
| Деталь: | HINGE, ADF, LEFT |
| Парткод: | FE8-2341-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE8-1580-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FE8-1582-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1586-000 |
| Деталь: | HINGE, ADF, RIGHT |
| Парткод: | FE8-2342-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1590-000 |
| Деталь: | HOLDER, DOUBLE FEED DETECTION |
| Парткод: | FE8-1865-000 |
| Деталь: | HOLDER, LED |
| Парткод: | FE8-1882-000 |
| Деталь: | COVER, LED |
| Парткод: | FE8-1883-000 |
| Деталь: | HOLDER, PAPER DELIVERY SENSOR |
| Парткод: | FE8-1884-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1890-000 |
| Деталь: | DOCUMENT TRAY ASSEMBLY |
| Парткод: | FM1-L783-000 |
| Деталь: | COUPLING |
| Парткод: | FE8-2329-000 |
| Деталь: | COUPLING |
| Парткод: | FE8-2330-000 |
| Деталь: | ROLLER, TENSIONER |
| Парткод: | FE8-2332-000 |
| Деталь: | GUIDE, CABLE, REAR |
| Парткод: | FE8-2333-000 |
| Деталь: | GUIDE, CABLE, LOWER |
| Парткод: | FE8-2334-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE8-2335-000 |
| Деталь: | COVER, CABLE |
| Парткод: | FE8-2338-000 |
| Деталь: | ROLLER, TENSIONER |
| Парткод: | FE8-2339-000 |
| Деталь: | COVER, USB |
| Парткод: | FE8-2355-000 |
| Деталь: | COVER,BOTTOM |
| Парткод: | FE8-2356-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE8-2419-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FE8-2426-000 |
| Деталь: | LEVER |
| Парткод: | FE8-2443-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-2623-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-2624-000 |
| Деталь: | DAMPER |
| Парткод: | FE8-3710-000 |
| Деталь: | PAD, PICK-UP |
| Парткод: | FE8-3713-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-3716-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FE8-3973-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FE8-6364-000 |
| Деталь: | FAN |
| Парткод: | FK2-0472-010 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-3805-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK4-3808-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK4-3995-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1428-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0289-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-5405-000 |
| Деталь: | ROLLER, READ, 1 |
| Парткод: | FL1-0267-000 |
| Деталь: | ROLLER, READ, 2 |
| Парткод: | FL1-0268-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FL1-0269-000 |
| Деталь: | CUSHION |
| Парткод: | FL0-5178-000 |
| Деталь: | GUIDE, PLATEN |
| Парткод: | FL1-0441 -000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FL1-0740-000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-1512-000 |
| Деталь: | GUIDE, SEPARATION |
| Парткод: | FL1-1513-000 |
| Деталь: | CONTACT IMAGE SENSOR ASSY SET |
| Парткод: | FM1-L777-010 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2057-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2174-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2175-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FL1-3412-000 |
| Деталь: | EJECT LIGHT LED PCB ASSY |
| Парткод: | FM0-0294-000 |
| Деталь: | LEAD 1 OUTER GUIDE ASSEMBLY |
| Парткод: | FM1-L785-010 |
| Деталь: | LEAD 2 OUTER GUIDE ASSEMBLY |
| Парткод: | FM1-L786-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-N521 -000 |
| Деталь: | CABLE, ADF MAIN |
| Парткод: | FM1-W888-000 |
| Деталь: | CABLE, DOUBLE FEED DETECTION |
| Парткод: | FM1-W889-000 |
| Деталь: | CABLE, ADF PASS SENSOR |
| Парткод: | FM1-W892-000 |
| Деталь: | MOTOR ASSY |
| Парткод: | FM1-W895-000 |
| Деталь: | PIN, SUS |
| Парткод: | XD9-0352-000 |
| Деталь: | BUSHING, PL |
| Парткод: | FS1-1528-000 |
| Деталь: | BUSHING |
| Парткод: | FS5-1805-000 |
| Деталь: | SCREW, STEPPED, M3 |
| Парткод: | FS5-9391-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-0595-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1417-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU2-1446-000 |
| Деталь: | SPRING, CLUTCH |
| Парткод: | FU2-1747-000 |
| Деталь: | GEAR, 38T |
| Парткод: | FU2-1749-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU2-1750-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU2-1751-000 |
| Деталь: | PULLEY, 18T |
| Парткод: | FU2-1752-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1754-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-1756-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1757-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1758-000 |
| Деталь: | PULLEY, 23T |
| Парткод: | FU2-1759-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1831-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU5-3643-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1572-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | PULLEY |
| Парткод: | FU8-0240-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0333-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1606-940 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-640 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1609-560 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1610-640 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-2003-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE8-2385-000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FE8-3531-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0290-000 |
| Деталь: | COVER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2056-000 |
| Деталь: | ROLLER, PAPER FEED, 1 |
| Парткод: | FC5-4286-000 |
| Деталь: | WEIGHT |
| Парткод: | FE4-5786-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FL0-5407-000 |
| Деталь: | SCREW,M3X4 |
| Парткод: | XA9-0624-000 |
| Деталь: | AUTO DOCUMENT FEEDER ASSY SET |
| Парткод: | FM1-L778-010 |
| Деталь: | STOPPER, FREE |
| Парткод: | FC0-7661-000 |
| Деталь: | SHAFT, LIFTER |
| Парткод: | FC0-7662-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FC8-4990-000 |
| Деталь: | GEAR, 68T/37T |
| Парткод: | FE3-1527-010 |
| Деталь: | ROLLER, CASSETTE |
| Парткод: | FE3-1528-010 |
| Деталь: | ARM, SIZE SENSOR LINK |
| Парткод: | FE3-3950-000 |
| Деталь: | SPACER |
| Парткод: | FE3-4476-000 |
| Деталь: | PIN, GUIDE |
| Парткод: | FE3-6143-000 |
| Деталь: | SHEET, SEPARATION |
| Парткод: | FL0-5121-000 |
| Деталь: | PLATE, PAPER SIDE END, FRONT |
| Парткод: | FM1-B545-000 |
| Деталь: | PLATE, BACK END LIMIT |
| Парткод: | FM1-B547-010 |
| Деталь: | PLATE, MIDDLE |
| Парткод: | FM1-B548-000 |
| Деталь: | CASSETTE COVER ASSEMBLY, FRONT |
| Парткод: | FM1-D705-000 |
| Деталь: | GEAR, 14T |
| Парткод: | RC1-9396-000 |
| Деталь: | ARM, GUIDE |
| Парткод: | FC0-7832-000 |
| Деталь: | PIN, ARM |
| Парткод: | FC0-7830-000 |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-1523-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0290-000 |
| Деталь: | LABEL, CASSETTE |
| Парткод: | FE4-1819-010 |
| Деталь: | BLOCK, PAPER SIDE END |
| Парткод: | FE3-9437-000 |
| Деталь: | PLATE, LINK |
| Парткод: | FE3-6357-000 |
| Деталь: | BLOCK, PAPER SIDE END, REAR |
| Парткод: | FE3-9436-000 |
| Деталь: | BLOCK, PAPER SIDE END, FRONT |
| Парткод: | FE3-9501-000 |
| Деталь: | LABEL, SIZE BACK END OPERATION |
| Парткод: | FE3-9591-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0359-000 |
| Деталь: | RACK, PAPER SIDE END |
| Парткод: | FE4-0306-000 |
| Деталь: | RACK, SIDE |
| Парткод: | FC0-7660-000 |
| Деталь: | PLATE, PAPER SIDE END, REAR |
| Парткод: | FE3-0481-000 |
| Деталь: | WASHER |
| Парткод: | FE8-6576-000 |
| Деталь: | LABEL, ENVELOPE OPERATION |
| Парткод: | FE3-7412-000 |
| Деталь: | CASSETTTE DAMPER UNIT |
| Парткод: | FM1-M249-000 |
| Деталь: | LABEL, CASSETTE SIZE |
| Парткод: | FE3-6479-000 |
| Деталь: | CASSETTE |
| Парткод: | FM1-D694-010 |
| Деталь: | LEVER, REMNANT DETECT |
| Парткод: | FE3-4041-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | PICK-UP LIFTER DRIVE ASSY |
| Парткод: | FM0-0018-000 |
| Деталь: | SPEAKER |
| Парткод: | FM0-0059-010 |
| Деталь: | H.V. CONTACT ASSEMBLY, COLOR |
| Парткод: | FM0-0043-000 |
| Деталь: | 1ST TRANS. H.V. CONTACT ASSY |
| Парткод: | FM4-9961-000 |
| Деталь: | PROCESS CONTROL PCB ASSY |
| Парткод: | FM4-9908-010 |
| Деталь: | CONTACT, 1ST TRANSFER H.V., 1 |
| Парткод: | FM0-0038-000 |
| Деталь: | I.T.B. RELEASE SWITCH ASSEMBLY |
| Парткод: | FM0-0039-010 |
| Деталь: | H.V. CONTACT ASSEMBLY, BLACK |
| Парткод: | FM0-0042-010 |
| Деталь: | 2ND TRANS. H.V. CONTACT ASSY |
| Парткод: | FM0-0079-000 |
| Деталь: | HEATER SWITCH ASSEMBLY |
| Парткод: | FM0-0084-000 |
| Деталь: | CASSETTE AUTO CLOSE ASSEMBLY |
| Парткод: | FM0-0017-020 |
| Деталь: | SENSOR, HUMIDITY |
| Парткод: | WP2-5410-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | CABLE, CASSETTE ASSY |
| Парткод: | FM1-A843-000 |
| Деталь: | 2ND TRANSFER H.V. PCB ASSEMBLY |
| Парткод: | FM1-R266-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7440-002 |
| Деталь: | HOLDER, REAR CASSETTE BOSS |
| Парткод: | FE4-8559-000 |
| Деталь: | MACHINE REAR PLATE 1 |
| Парткод: | NPN |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM1-R758-000 |
| Деталь: | SCREW, MACH. PAN HEAD, M3X4 |
| Парткод: | XA9-1979-000 |
| Деталь: | TPM PCB ASSEMBLY |
| Парткод: | FM1-M981-000 |
| Деталь: | CABLE, SATA POWER |
| Парткод: | FK4-3811-000 |
| Деталь: | CABLE, SATA SIGNAL |
| Парткод: | FK4-3810-000 |
| Деталь: | HARD DISK DRIVE, MQ01ABF032 |
| Парткод: | FK4-1550-000 |
| Деталь: | LABEL, CAUTION |
| Парткод: | FU8-8257-000 |
| Деталь: | DAMPER, CUSHION |
| Парткод: | XH9-0149-000 |
| Деталь: | SPACER |
| Парткод: | XZ1-1301-005 |
| Деталь: | IC, STANDARD SELL, MB8AA4600PB |
| Парткод: | FK3-3872-000 |
| Деталь: | IC, 88E8075-B0-NNC2C000-W553, |
| Парткод: | FK4-1861-000 |
| Деталь: | IC, R9A06G011GBG, MPU |
| Парткод: | FK4-2216-000 |
| Деталь: | IC, MB8AL1070MP-GE1, ASIC |
| Парткод: | FK4-1649-000 |
| Деталь: | CONTROLLER BOX ASSEMBLY |
| Парткод: | NPN |
| Деталь: | CLIP |
| Парткод: | FC0-1271-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CLIP |
| Парткод: | FC5-4424-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FC8-6316-010 |
| Деталь: | COVER, REAR |
| Парткод: | FE4-5751-000 |
| Деталь: | LEVER, READ SENSOR |
| Парткод: | FC8-6371-000 |
| Деталь: | JOINT, PICK-UP |
| Парткод: | FC8-6383-000 |
| Деталь: | LEVER, PAPER DELIVERY SENSOR |
| Парткод: | FE4-5701-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE4-5712-000 |
| Деталь: | COVER, CARD READER |
| Парткод: | FE4-5735-000 |
| Деталь: | GUIDE, CABLE, FRONT |
| Парткод: | FE4-5746-000 |
| Деталь: | ARM, JOINT |
| Парткод: | FE4-5761-000 |
| Деталь: | LABEL |
| Парткод: | FE4-5779-000 |
| Деталь: | DOUBLE FEED DETECTION KIT |
| Парткод: | FM1-K086-010 |
| Деталь: | STOPPER, CLUTCH ROTATION |
| Парткод: | FE4-5788-000 |
| Деталь: | FRAME, BASE |
| Парткод: | FE4-5790-000 |
| Деталь: | LEVER, DRIVE RELEASE |
| Парткод: | FE4-5796-000 |
| Деталь: | HINGE, ADF, LEFT |
| Парткод: | FE8-2341-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE8-1580-000 |
| Деталь: | HOLDER, SENSOR |
| Парткод: | FE8-1582-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1586-000 |
| Деталь: | HINGE, ADF, RIGHT |
| Парткод: | FE8-2342-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1590-000 |
| Деталь: | HOLDER, DOUBLE FEED DETECTION |
| Парткод: | FE8-1865-000 |
| Деталь: | HOLDER, LED |
| Парткод: | FE8-1882-000 |
| Деталь: | COVER, LED |
| Парткод: | FE8-1883-000 |
| Деталь: | HOLDER, PAPER DELIVERY SENSOR |
| Парткод: | FE8-1884-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-1890-000 |
| Деталь: | DOCUMENT TRAY ASSEMBLY |
| Парткод: | FM1-L783-000 |
| Деталь: | COUPLING |
| Парткод: | FE8-2329-000 |
| Деталь: | COUPLING |
| Парткод: | FE8-2330-000 |
| Деталь: | ROLLER, TENSIONER |
| Парткод: | FE8-2332-000 |
| Деталь: | GUIDE, CABLE, REAR |
| Парткод: | FE8-2333-000 |
| Деталь: | GUIDE, CABLE, LOWER |
| Парткод: | FE8-2334-000 |
| Деталь: | GUIDE, CABLE |
| Парткод: | FE8-2335-000 |
| Деталь: | COVER, CABLE |
| Парткод: | FE8-2338-000 |
| Деталь: | ROLLER, TENSIONER |
| Парткод: | FE8-2339-000 |
| Деталь: | COVER, USB |
| Парткод: | FE8-2355-000 |
| Деталь: | COVER,BOTTOM |
| Парткод: | FE8-2356-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE8-2419-000 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FE8-2426-000 |
| Деталь: | LEVER |
| Парткод: | FE8-2443-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-2623-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-2624-000 |
| Деталь: | DAMPER |
| Парткод: | FE8-3710-000 |
| Деталь: | PAD, PICK-UP |
| Парткод: | FE8-3713-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE8-3716-000 |
| Деталь: | ROLLER, PLATEN |
| Парткод: | FE8-3973-000 |
| Деталь: | LABEL, DOCUMENT MAXIMUM LOAD |
| Парткод: | FE8-6364-000 |
| Деталь: | FAN |
| Парткод: | FK2-0472-010 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK4-3805-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK4-3808-000 |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | FK4-3995-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL0-1428-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0289-000 |
| Деталь: | DAMPER |
| Парткод: | FL0-5405-000 |
| Деталь: | ROLLER, READ, 1 |
| Парткод: | FL1-0267-000 |
| Деталь: | ROLLER, READ, 2 |
| Парткод: | FL1-0268-000 |
| Деталь: | ROLLER, DELIVERY |
| Парткод: | FL1-0269-000 |
| Деталь: | CUSHION |
| Парткод: | FL0-5178-000 |
| Деталь: | GUIDE, PLATEN |
| Парткод: | FL1-0441 -000 |
| Деталь: | ROLLER, REGISTRATION |
| Парткод: | FL1-0740-000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-1512-000 |
| Деталь: | GUIDE, SEPARATION |
| Парткод: | FL1-1513-000 |
| Деталь: | CONTACT IMAGE SENSOR ASSY SET |
| Парткод: | FM1-L777-010 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2057-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2174-000 |
| Деталь: | SPACER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2175-000 |
| Деталь: | ROLLER, READ |
| Парткод: | FL1-3412-000 |
| Деталь: | EJECT LIGHT LED PCB ASSY |
| Парткод: | FM0-0294-000 |
| Деталь: | LEAD 1 OUTER GUIDE ASSEMBLY |
| Парткод: | FM1-L785-010 |
| Деталь: | LEAD 2 OUTER GUIDE ASSEMBLY |
| Парткод: | FM1-L786-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM1-N521 -000 |
| Деталь: | CABLE, ADF MAIN |
| Парткод: | FM1-W888-000 |
| Деталь: | CABLE, DOUBLE FEED DETECTION |
| Парткод: | FM1-W889-000 |
| Деталь: | CABLE, ADF PASS SENSOR |
| Парткод: | FM1-W892-000 |
| Деталь: | MOTOR ASSY |
| Парткод: | FM1-W895-000 |
| Деталь: | PIN, SUS |
| Парткод: | XD9-0352-000 |
| Деталь: | BUSHING, PL |
| Парткод: | FS1-1528-000 |
| Деталь: | BUSHING |
| Парткод: | FS5-1805-000 |
| Деталь: | SCREW, STEPPED, M3 |
| Парткод: | FS5-9391-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-0595-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1417-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU2-1446-000 |
| Деталь: | SPRING, CLUTCH |
| Парткод: | FU2-1747-000 |
| Деталь: | GEAR, 38T |
| Парткод: | FU2-1749-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU2-1750-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU2-1751-000 |
| Деталь: | PULLEY, 18T |
| Парткод: | FU2-1752-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1754-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU2-1756-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-1757-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU2-1758-000 |
| Деталь: | PULLEY, 23T |
| Парткод: | FU2-1759-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-1831-000 |
| Деталь: | PULLEY, 22T |
| Парткод: | FU5-3643-000 |
| Деталь: | BUSHING |
| Парткод: | FU6-1572-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU7-2658-000 |
| Деталь: | PULLEY |
| Парткод: | FU8-0240-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-008 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0333-000 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1606-940 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-640 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1609-560 |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1610-640 |
| Деталь: | SCREW, W/WASHER, M3X6 |
| Парткод: | XA9-2003-000 |
| Деталь: | HOLDER, ROLLER |
| Парткод: | FE8-2385-000 |
| Деталь: | HOLDER, CONTACT IMAGE SENSOR |
| Парткод: | FE8-3531-000 |
| Деталь: | PIN, PARALLEL |
| Парткод: | XD9-0290-000 |
| Деталь: | COVER, CONTACT IMAGE SENSOR |
| Парткод: | FL1-2056-000 |
| Деталь: | ROLLER, PAPER FEED, 1 |
| Парткод: | FC5-4286-000 |
| Деталь: | WEIGHT |
| Парткод: | FE4-5786-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FL0-5407-000 |
| Деталь: | SCREW,M3X4 |
| Парткод: | XA9-0624-000 |
| Деталь: | AUTO DOCUMENT FEEDER ASSY SET |
| Парткод: | FM1-L778-010 |
| Деталь: | SHAFT |
| Парткод: | FC0-5875-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5888-000 |
| Деталь: | SHAFT |
| Парткод: | FC0-5935-000 |
| Деталь: | PANEL, RIGHT DOOR, FRONT |
| Парткод: | FE3-9093-000 |
| Деталь: | PANEL, CABLE |
| Парткод: | FE3-9094-000 |
| Деталь: | FLAG, DUPLEXING SENSOR |
| Парткод: | FC0-5943-000 |
| Деталь: | COVER, BLANKING |
| Парткод: | FE3-9097-000 |
| Деталь: | LINK, RELEASE |
| Парткод: | FC0-7446-000 |
| Деталь: | GUIDE, LOCK, FRONT |
| Парткод: | FC0-7535-010 |
| Деталь: | GUIDE, LOCK, REAR |
| Парткод: | FC0-7536-000 |
| Деталь: | SUPPORT, ROLLER |
| Парткод: | FE3-1547-010 |
| Деталь: | BUSHING |
| Парткод: | FE3-1617-000 |
| Деталь: | COVER, PAPER FEED ROLLER |
| Парткод: | FL0-7724-000 |
| Деталь: | HOLDER, MULTI FEED SWING |
| Парткод: | FE3-1760-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-2409-000 |
| Деталь: | SHAFT |
| Парткод: | FE3-3585-000 |
| Деталь: | SHAFT |
| Парткод: | FE3-3594-000 |
| Деталь: | GUIDE, SHUTTER LINK |
| Парткод: | FE3-4759-000 |
| Деталь: | SHUTTER, PAPER PICK-UP |
| Парткод: | FE3-4760-000 |
| Деталь: | LOCK, SHUTTER |
| Парткод: | FE3-4761-000 |
| Деталь: | LEVER, SHUTTER LINK |
| Парткод: | FE3-4762-000 |
| Деталь: | PAPER PICK-UP ROLLER SET |
| Парткод: | FM1-P088-000 |
| Деталь: | BOSS, TRAY |
| Парткод: | FE3-4765-000 |
| Деталь: | SHEET, FLAG SILENCER |
| Парткод: | FL0-1010-000 |
| Деталь: | CABLE, FAN GROUNDING, RIGHT |
| Парткод: | FE3-6116-000 |
| Деталь: | CABLE, GROUNDING, RIGHT |
| Парткод: | FE3-6117-000 |
| Деталь: | FAN |
| Парткод: | FK2-0472-010 |
| Деталь: | SOLENOID |
| Парткод: | FK4-0725-000 |
| Цена: | 1 400 ₽ |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-4002-000 |
| Цена: | 4 900 ₽ |
| Деталь: | CLUTCH, ONE-WAY |
| Парткод: | FL0-1361 -000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5654-000 |
| Деталь: | ROLLER, DUPLEXING FEED |
| Парткод: | FL3-6443-000 |
| Деталь: | DOOR HOOK ASSEMBLY, RIGHT |
| Парткод: | FM1-D707-000 |
| Деталь: | DUPLEXING INNER GUIDE ASSEMBLY |
| Парткод: | FM1-B552-000 |
| Деталь: | RIGHT INNER DOOR ASSEMBLY |
| Парткод: | FM1-B553-000 |
| Деталь: | 2ND TRNSFR. OUTER GUIDE ASSY |
| Парткод: | FM1-B554-010 |
| Деталь: | SENSOR UNIT, LOOP |
| Парткод: | FM1-B555-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | ROLLER, 2ND TRNSFR. OUTER |
| Парткод: | FE2-A308-000 |
| Деталь: | HOLDER, BUSHING, FRONT |
| Парткод: | FC0-5861 -010 |
| Деталь: | HOLDER, BUSHING, REAR |
| Парткод: | FC0-5862-000 |
| Деталь: | 2ND TRNSFR. OUTER ROLLER ASSY |
| Парткод: | FM1-U036-000 |
| Деталь: | BEARING, BALL, L-1060ZZ |
| Парткод: | XG9-0783-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0192-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU2-0197-000 |
| Деталь: | GEAR, 27T |
| Парткод: | FU2-0198-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU2-0257-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU2-0259-000 |
| Деталь: | GEAR, 17T |
| Парткод: | FU2-0358-000 |
| Деталь: | GEAR, 19T |
| Парткод: | FU9-0662-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU9-0663-000 |
| Деталь: | PLANETARY GEAR ASSEMBLY |
| Парткод: | FM1-K539-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU9-0666-000 |
| Деталь: | COVER, ROLLER |
| Парткод: | FE3-0389-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU9-0668-000 |
| Деталь: | COVER, ROLLER |
| Парткод: | FC0-6614-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU9-2068-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2069-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2070-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2071-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2112-010 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2224-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-006 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CABLE, DOOR, RIGHT |
| Парткод: | FM1-A825-000 |
| Деталь: | CABLE, DOOR FAN, RIGHT |
| Парткод: | FM1-A827-000 |
| Деталь: | SHEET, DAMPER |
| Парткод: | FL1-4036-000 |
| Деталь: | DOOR ASSEMBLY, RIGHT |
| Парткод: | FM1-U038-000 |
| Деталь: | RAIL, PAPER PICK-UP, MIDDLE |
| Парткод: | FC0-7188-000 |
| Деталь: | BLOCK, PROCESS PRESSURE, FRONT |
| Парткод: | FM4-9906-000 |
| Деталь: | STOPPER, PROCESS UNIT, FRONT |
| Парткод: | FC0-7728-000 |
| Деталь: | RAIL ASSEMBLY, LEFT |
| Парткод: | FM4-9907-000 |
| Деталь: | LEVER, PROCESS KIT, REAR |
| Парткод: | FM4-9905-000 |
| Деталь: | SHUTTER LINK ASSEMBLY |
| Парткод: | FM0-0032-000 |
| Деталь: | SPRING |
| Парткод: | FC9-8607-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | SPRING |
| Парткод: | FC0-7068-000 |
| Деталь: | RAIL, PROCESS CARTRIDGE, RIGHT |
| Парткод: | FC0-6502-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | FAN |
| Парткод: | FK2-3679-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7440-003 |
| Деталь: | DELIVERY COOLING FAN ASSEMBLY |
| Парткод: | NPN |
| Деталь: | COVER, FRONT, UPPER |
| Парткод: | FL1-0149-000 |
| Деталь: | BAND, FRONT COVER, RIGHT |
| Парткод: | FC0-7572-000 |
| Деталь: | PIN, FRONT |
| Парткод: | FC0-7734-000 |
| Деталь: | HOOK, COVER, FRONT |
| Парткод: | FE3-9086-000 |
| Деталь: | ROD, GLASS CLEANING |
| Парткод: | FL0-0237-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU9-2007-000 |
| Деталь: | LABEL, CLN ROD OPERATION |
| Парткод: | FC0-5846-010 |
| Деталь: | LABEL, LASER CAUTION |
| Парткод: | FU6-8646-000 |
| Деталь: | LABEL, SERVICE |
| Парткод: | FL0-5404-000 |
| Деталь: | LABEL, SERVICE |
| Парткод: | FL3-6545-000 |
| Деталь: | LABEL, TONER TYPE |
| Парткод: | FE8-8494-000 |
| Деталь: | LABEL,EXCHANGE OPERATOR,BOTTLE |
| Парткод: | FC0-7807-000 |
| Деталь: | DOOR ASSEMBLY, FRONT |
| Парткод: | FM1-L549-000 |
| Деталь: | FAN |
| Парткод: | FK2-3679-000 |
| Деталь: | CARTRIDGE AIR INTAKE FAN ASSY |
| Парткод: | NPN |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | GUIDE, DUPLEXING |
| Парткод: | FC0-5886-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5888-000 |
| Деталь: | ROLLER, DUPLEXING FEED |
| Парткод: | FL3-6443-000 |
| Деталь: | PLANETARY ONE-WAY GEAR ASSY |
| Парткод: | FM1-B551-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU9-0663-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU9-0666-000 |
| Деталь: | GEAR, 25T/14T |
| Парткод: | FU9-0672-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU9-0720-000 |
| Деталь: | SHEET, DAMPER |
| Парткод: | FL1-4036-000 |
| Деталь: | DUPLEXING GUIDE ASSEMBLY |
| Парткод: | NPN |
| Деталь: | POWER SUPPLY ASSEMBLY |
| Парткод: | FM1-P022-000 |
| Деталь: | ADF MAINTENANCE KIT, DR-203 |
| Парткод: | FM1-P720-000 |
| Деталь: | ADF MAINTENANCE KIT |
| Парткод: | NPN |
| Деталь: | INTER. TRANSFER BELT ASSY |
| Парткод: | FM1-A153-020 |
| Деталь: | PRESSURE ROLLER KIT |
| Парткод: | FM1-K198-010 |
| Деталь: | HOLDER, BEARING |
| Парткод: | FC0-6079-000 |
| Деталь: | CAM,PRESSURE RELEASE |
| Парткод: | FC0-6086-000 |
| Деталь: | PLATE, PRESSURE, REAR |
| Парткод: | FC0-6088-000 |
| Деталь: | FLAG, PAPER DELIVERY SENSOR |
| Парткод: | FC0-6092-010 |
| Деталь: | PLATE, PRESSURE, LEFT |
| Парткод: | FC0-6131-000 |
| Деталь: | LOCK, SHUTTER, FRONT |
| Парткод: | FC0-6156-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC0-6157-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM1-R729-000 |
| Деталь: | CABLE, FIXING ASSEMBLY |
| Парткод: | FM1-A802-000 |
| Деталь: | GUIDE, FIXING ENTRANCE |
| Парткод: | FC0-6089-010 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU2-0230-000 |
| Деталь: | GEAR, 29T |
| Парткод: | FU9-0610-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU9-0611-000 |
| Деталь: | GEAR, 30T |
| Парткод: | FU9-0612-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2104-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2105-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2106-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2111-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | IC,PHOTO-INTERRUPTER,LG248NL1A |
| Парткод: | WG8-5783-000 |
| Деталь: | BEARING, BALL, L-1260ZZR |
| Парткод: | XG9-0865-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-006 |
| Деталь: | DAMPER |
| Парткод: | FL0-6873-000 |
| Деталь: | FIXING ASSEMBLY, FX-201 |
| Парткод: | FM1-R726-010 |
| Деталь: | DUST-PROOF SHUTTER ASSEMBLY |
| Парткод: | FM0-0031-000 |
| Деталь: | CABLE, LASER SCANNER |
| Парткод: | FM1-A823-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU9-2181-000 |
| Деталь: | LASER SCANNER ASSEMBLY |
| Парткод: | FM0-0144-000 |
| Деталь: | LASER SCANNER ASSEMBLY |
| Парткод: | NPN |
| Деталь: | SHEET, PROTECTION |
| Парткод: | FL0-3763-000 |
| Деталь: | RAIL, I.T.B., FRONT |
| Парткод: | FM0-0035-000 |
| Деталь: | RAIL, I.T.B., REAR |
| Парткод: | FM0-0036-010 |
| Деталь: | HOLDER, FIXING LOCK |
| Парткод: | FM0-0074-000 |
| Деталь: | FIXING GROUNDING ASSEMBLY |
| Парткод: | FM1-B572-000 |
| Деталь: | CONNECTING CABLE ASSEMBLY |
| Парткод: | FM1-C324-000 |
| Деталь: | PLATE ASSEMBLY |
| Парткод: | FM1-C347-000 |
| Деталь: | REGISTRATION SENSOR ASSEMBLY |
| Парткод: | FM1-F727-000 |
| Деталь: | HOLDER, FIXING, FRONT |
| Парткод: | FM4-9910-000 |
| Деталь: | HOLDER, FIXING, REAR |
| Парткод: | FM4-9911-000 |
| Деталь: | SCREW,RS,M3X8 |
| Парткод: | XA9-1386-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | COVER, CONTROL PANEL ASSEMBLY |
| Парткод: | FM1-L540-000 |
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FM1-L554-000 |
| Деталь: | COVER, UPPER |
| Парткод: | FM1-L544-000 |
| Деталь: | COVER, REAR UPPER |
| Парткод: | FM1-D699-010 |
| Деталь: | COVER, RIGHT LOWER |
| Парткод: | FE3-9079-000 |
| Деталь: | COVER, ENV. HEATER SWITCH |
| Парткод: | FE3-9087-000 |
| Деталь: | COVER, REAR, 2 |
| Парткод: | FE4-9082-000 |
| Деталь: | SEAL |
| Парткод: | FC6-4513-000 |
| Деталь: | COVER, CONTROL HINGE, REAR |
| Парткод: | FE8-4215-000 |
| Деталь: | COVER, PAPER DELIVERY |
| Парткод: | FE8-4216-000 |
| Деталь: | COVER, RIGHT FRONT |
| Парткод: | FL0-2604-000 |
| Деталь: | COVER, RIGHT REAR |
| Парткод: | FL0-2606-000 |
| Деталь: | COVER, RIGHT UPPER |
| Парткод: | FL0-2605-000 |
| Деталь: | SHEET, PAPER DELIVERY TRAY, 2 |
| Парткод: | FL0-1008-000 |
| Деталь: | COVER,LEFT UPPER |
| Парткод: | FE8-4211-000 |
| Деталь: | COVER, DEVICE PORT |
| Парткод: | FE3-9082-000 |
| Деталь: | COVER, FAX CONNECTOR |
| Парткод: | FE3-9088-000 |
| Деталь: | COVER, LEFT LOWER |
| Парткод: | FL0-5332-000 |
| Деталь: | LABEL, TONER |
| Парткод: | FE4-1818-000 |
| Деталь: | COVER,LOUVER |
| Парткод: | FE4-9079-000 |
| Деталь: | COVER, REAR, 1 |
| Парткод: | FE4-9078-000 |
| Деталь: | COVER, HEATER, ENVIRONMENT |
| Парткод: | FE3-9089-000 |
| Деталь: | LABEL, FAX |
| Парткод: | FE8-4239-000 |
| Деталь: | COVER, LOUVER, 1 |
| Парткод: | FE4-9095-000 |
| Деталь: | HOLDER, SERVICE BOOK |
| Парткод: | FE4-3758-000 |
| Деталь: | SHEET, PAPER DELIVERY TRAY |
| Парткод: | FL0-1007-000 |
| Деталь: | COVER, CONTROL PANEL CABLE |
| Парткод: | FE4-9431-000 |
| Деталь: | DAMPER UNIT, AIR |
| Парткод: | FC7-6142-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | FLAPPER, REVERSE |
| Парткод: | FC0-5880-000 |
| Деталь: | HOLDER, DUPLEXING SWING GEAR |
| Парткод: | FC0-5891-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FC0-5892-000 |
| Деталь: | GUIDE, ENTRANCE |
| Парткод: | FE3-9461-000 |
| Деталь: | FLAG, FULL DETECT |
| Парткод: | FC0-6102-000 |
| Деталь: | ROLLER, PAPER DELIVERY, UPPER |
| Парткод: | FC0-7698-000 |
| Деталь: | ROLLER, PAPER DELIVERY, LOWER |
| Парткод: | FC0-7699-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FE3-3744-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-3745-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | FE3-5739-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FE3-5740-000 |
| Деталь: | ROLLER, FIXING PAPER DELIVERY |
| Парткод: | FE3-6111-000 |
| Деталь: | SHEET, FLAG, SILENCER |
| Парткод: | FL0-1009-000 |
| Деталь: | SHEET, FLAG SILENCER |
| Парткод: | FL0-1010-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FL0-1833-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-0718-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-0719-000 |
| Деталь: | BUSHING |
| Парткод: | FU2-0720-000 |
| Деталь: | GEAR, 9T |
| Парткод: | FU2-0810-000 |
| Деталь: | GEAR, 9T |
| Парткод: | FU2-0811-000 |
| Деталь: | GEAR, 9T/9T |
| Парткод: | FU2-0812-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0613-000 |
| Деталь: | GEAR, 17T |
| Парткод: | FU9-0675-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU9-0676-000 |
| Деталь: | GEAR, 29T |
| Парткод: | FU9-0677-000 |
| Деталь: | GEAR, 17T/15T |
| Парткод: | FU9-0680-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU9-2108-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2191-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-8410-000 |
| Деталь: | CLIP, SHAFT, UPPER |
| Парткод: | FC0-7828-000 |
| Деталь: | CLIP, SHAFT, LOWER |
| Парткод: | FC0-7827-000 |
| Деталь: | BUSHING |
| Парткод: | FE3-8411-000 |
| Деталь: | ROLLER, H DRIVEN |
| Парткод: | FC7-6108-000 |
| Деталь: | PAPER DELIVERY/REVERSE ASSY |
| Парткод: | FM0-0021-000 |
| Деталь: | SHAFT |
| Парткод: | FC0-5875-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5876-000 |
| Деталь: | BUSHING |
| Парткод: | FC0-5888-000 |
| Деталь: | SHAFT |
| Парткод: | FC0-5935-000 |
| Деталь: | PANEL, RIGHT DOOR, FRONT |
| Парткод: | FE3-9093-000 |
| Деталь: | PANEL, CABLE |
| Парткод: | FE3-9094-000 |
| Деталь: | FLAG, DUPLEXING SENSOR |
| Парткод: | FC0-5943-000 |
| Деталь: | COVER, BLANKING |
| Парткод: | FE3-9097-000 |
| Деталь: | LINK, RELEASE |
| Парткод: | FC0-7446-000 |
| Деталь: | GUIDE, LOCK, FRONT |
| Парткод: | FC0-7535-010 |
| Деталь: | GUIDE, LOCK, REAR |
| Парткод: | FC0-7536-000 |
| Деталь: | SUPPORT, ROLLER |
| Парткод: | FE3-1547-010 |
| Деталь: | BUSHING |
| Парткод: | FE3-1617-000 |
| Деталь: | COVER, PAPER FEED ROLLER |
| Парткод: | FL0-7724-000 |
| Деталь: | HOLDER, MULTI FEED SWING |
| Парткод: | FE3-1760-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FE3-2409-000 |
| Деталь: | SHAFT |
| Парткод: | FE3-3585-000 |
| Деталь: | SHAFT |
| Парткод: | FE3-3594-000 |
| Деталь: | GUIDE, SHUTTER LINK |
| Парткод: | FE3-4759-000 |
| Деталь: | SHUTTER, PAPER PICK-UP |
| Парткод: | FE3-4760-000 |
| Деталь: | LOCK, SHUTTER |
| Парткод: | FE3-4761-000 |
| Деталь: | LEVER, SHUTTER LINK |
| Парткод: | FE3-4762-000 |
| Деталь: | PAPER PICK-UP ROLLER SET |
| Парткод: | FM1-P088-000 |
| Деталь: | BOSS, TRAY |
| Парткод: | FE3-4765-000 |
| Деталь: | SHEET, FLAG SILENCER |
| Парткод: | FL0-1010-000 |
| Деталь: | CABLE, FAN GROUNDING, RIGHT |
| Парткод: | FE3-6116-000 |
| Деталь: | CABLE, GROUNDING, RIGHT |
| Парткод: | FE3-6117-000 |
| Деталь: | FAN |
| Парткод: | FK2-0472-010 |
| Деталь: | SOLENOID |
| Парткод: | FK4-0725-000 |
| Цена: | 1 400 ₽ |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | FL0-4002-000 |
| Цена: | 4 900 ₽ |
| Деталь: | CLUTCH, ONE-WAY |
| Парткод: | FL0-1361 -000 |
| Деталь: | BUSHING |
| Парткод: | FE3-5654-000 |
| Деталь: | ROLLER, DUPLEXING FEED |
| Парткод: | FL3-6443-000 |
| Деталь: | DOOR HOOK ASSEMBLY, RIGHT |
| Парткод: | FM1-D707-000 |
| Деталь: | DUPLEXING INNER GUIDE ASSEMBLY |
| Парткод: | FM1-B552-000 |
| Деталь: | RIGHT INNER DOOR ASSEMBLY |
| Парткод: | FM1-B553-000 |
| Деталь: | 2ND TRNSFR. OUTER GUIDE ASSY |
| Парткод: | FM1-B554-010 |
| Деталь: | SENSOR UNIT, LOOP |
| Парткод: | FM1-B555-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | ROLLER, 2ND TRNSFR. OUTER |
| Парткод: | FE2-A308-000 |
| Деталь: | HOLDER, BUSHING, FRONT |
| Парткод: | FC0-5861 -010 |
| Деталь: | HOLDER, BUSHING, REAR |
| Парткод: | FC0-5862-000 |
| Деталь: | 2ND TRNSFR. OUTER ROLLER ASSY |
| Парткод: | FM1-U036-000 |
| Деталь: | BEARING, BALL, L-1060ZZ |
| Парткод: | XG9-0783-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU2-0192-000 |
| Деталь: | GEAR, 16T |
| Парткод: | FU2-0197-000 |
| Деталь: | GEAR, 27T |
| Парткод: | FU2-0198-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU2-0257-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU2-0259-000 |
| Деталь: | GEAR, 17T |
| Парткод: | FU2-0358-000 |
| Деталь: | GEAR, 19T |
| Парткод: | FU9-0662-000 |
| Деталь: | GEAR, 25T |
| Парткод: | FU9-0663-000 |
| Деталь: | PLANETARY GEAR ASSEMBLY |
| Парткод: | FM1-K539-000 |
| Деталь: | GEAR, 23T |
| Парткод: | FU9-0666-000 |
| Деталь: | COVER, ROLLER |
| Парткод: | FE3-0389-000 |
| Деталь: | GEAR, 14T |
| Парткод: | FU9-0668-000 |
| Деталь: | COVER, ROLLER |
| Парткод: | FC0-6614-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU9-2068-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2069-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2070-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2071-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2112-010 |
| Деталь: | SPRING, TORSION |
| Парткод: | FU9-2224-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-002 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-003 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7207-006 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CABLE, DOOR, RIGHT |
| Парткод: | FM1-A825-000 |
| Деталь: | CABLE, DOOR FAN, RIGHT |
| Парткод: | FM1-A827-000 |
| Деталь: | SHEET, DAMPER |
| Парткод: | FL1-4036-000 |
| Деталь: | DOOR ASSEMBLY, RIGHT |
| Парткод: | FM1-U038-000 |
Коды ошибок
E001-A001-05
E001-A002-05
E001-A003-05
E001-A004-05
E001-A005-05
E001-A006-05
E002-A001-05
E002-A002-05
E002-A003-05
E002-A004-05
E003-A001-05
E003-A002-05
E003-A003-05
E004-0001-05
E004-0002-05
E009-0001-05
E009-0002-05
E009-0003-05
E009-0004-05
E009-0006-05
E010-0001-05
E010-0002-05
E010-0003-05
E012-0001-05
E012-0002-05
E012-0003-05
E014-0001-05
E014-0002-05
E014-0003-05
E020-01A8-05
E020-01B8-05
E020-01C0-05
E020-01F0-05
E020-02A8-05
E020-02B8-05
E020-02C0-05
E020-02F0-05
E020-03A8-05
E020-03B8-05
E020-03C0-05
E020-03F0-05
E020-04A8-05
E020-04B8-05
E020-04C0-05
E020-04F0-05
E021-0001-05
E021-0002-05
E021-0003-05
E021-0120-05
E021-0220-05
E021-0320-05
E021-0420-05
E025-0110-05
E025-0168-05
E025-0210-05
E025-0268-05
E025-0310-05
E025-0368-05
E025-0410-05
E025-0468-05
E029-5008-05
E029-7008-05
E073-0001-05
E074-0000-05
E074-0002-05
E100-0001-05
E102-0001-05
E110-0001-05
E110-0002-05
E110-0003-05
E110-0005-05
E193-0000-05
E193-0101-05
E193-0F00-05
E196-0000-05 ... E196-0102-05
E196-010F-05
E196-020F-05 ... E196-050F-05
E196-0800-05 ... E196-0802-05
E196-080F-05
E196-090F-05
E197-0000-05 ... E197-0F00-05
E197-1000-05
E197-1101-05
E197-1F00-05
E197-2000-05
E197-2101-05
E197-2F00-05
E202-0001-04
E202-0002-04
E227-0001-04
E240-0000-05
E240-0002-00
E246-0001-00 ... E246-0005-00
E247-0001-00 ... E247-0004-00
E248-0001-04
E248-0002-04
E280-0001-04
E280-0002-04
E280-0101-04
E280-0102-04
E302-0001-04 ... E302-0103-04
E315-0007-00 ... E315-0510-00
E315-0530-00
E315-0531-00
E315-0540-00
E315-0541-00
E350-0000-00 ... E350-3000-00
E351-0000-00
E354-0001-00 ... E355-0004-00
E412-0005-04
E412-0006-04
E423-0001-04
E500-0000-02
E530-0001-02
E530-0002-02
E531-8001-02
E531-8002-02
E537-0001-02
E537-0002-02
E540-0001-02
E575-0001-02
E575-0002-02
E575-0004-02
E577-0001-02
E577-0002-02
E583-0001-02
E583-0002-02
E602-0001-00
E602-0020-00
E602-0101-00
E602-0111-00
E602-0201-00
E602-0211-00
E602-0301-00
E602-0311-00
E602-0401-00
E602-0411-00
E602-0501-00
E602-0511-00
E602-0601-00
E602-0611-00
E602-0701-00
E602-0711-00
E602-0801-00
E602-0811-00
E602-0901-00
E602-0911-00
E602-1001-00
E602-1011-00
E602-1101-00
E602-1111-00
E602-1201-00
E602-1211-00
E602-1301-00
E602-1311-00
E602-1401-00
E602-1411-00
E602-1701-00
E602-1711-00
E602-1801-00
E602-1811-00
E602-1901-00
E602-1911-00
E602-2000-00
E602-2001-00
E602-2002-00
E602-5001-00
E602-5002-00
E602-FF01-00
E602-FF11-00
E604-1024-00 ... E613-1536-00
E613-2048-00
E614-0001-00 ... E614-0411-00
E614-0501-00
E614-0511-00
E614-0601-00
E614-0611-00
E614-0701-00
E614-0711-00
E614-4000-00 ... E614-4003-00
E614-4010-00 ... E614-9000-00
E614-9001-00 ... E614-9004-00
E614-FF01-00
E614-FF11-00
E615-0001-00
E674-0001-07 ... E674-0008-07
E674-0010-07, E674-0011-07
E674-0020-07
E674-0021-07
E674-0030-07
E674-0100-07
E674-0300-07
E674-0301-07
E713-0000-05
E719-0001-00
E719-0002-00
E719-0003-00
E719-0004-00
E719-0031-00
E719-0032-00
E719-0041-00
E719-0042-00
E720-0001-00
E720-0001-05
E730-C001-00
E732-0001-04
E732-0010-00
E732-0020-00
E732-0021-00
E732-0022-00
E732-0023-04
E732-0F01-04
E732-0F20-00
E732-0F21-00
E732-0F22-00
E732-0F23-04
E733-0000-05
E733-0001-05
E733-0002-05
E733-0F00-05 ... E733-0F02-05
E733-F000-05, E733-F001-05
E733-F002-05
E743-0000-04
E744-0001-00
E744-0003-00
E744-0004-00
E744-2000-00
E744-5000-07
E746-0011-00
E746-0021-00
E746-0022-00
E746-0023-00
E746-0024-00
E746-0031-00
E746-0032-00
E746-0033-00
E746-0034-00
E746-0035-00
E748-2000-00, E748-2001-00
E748-2010-00
E748-2011-00
E748-2012-00
E748-2021-00 ... E748-4910-00
E748-9000-00
E749-0008-00
E753-0001-00
E760-0001-00
E804-0000-00
E806-0100-05
E806-0101-05
E806-0300-05
E806-0301-05
E806-0400-05
E806-0401-05
E808-0001-05
E880-0001-00
E880-0003-00
E880-0005-00
E881-0001-00
E882-0001-05
E996-0071-04
E996-0CA1-05
E996-0CA2-05
E996-0CA3-05
E996-0CA4-05
E996-0CA9-05
E996-0CAD-05
E996-0CAE-05
E996-0CAF-05
Описание
| Error code: | E001-A001-05 |
| Description: | Fixing Main Thermistor high temperature detection error |
| Causes: | The Fixing Main Thermistor detected 265 deg C or higher for 0.1 sec or longer. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E001-A002-05 |
| Description: | Sub Thermistor (Front) high temperature detection error |
| Causes: | The Sub Thermistor (Front) detected 290 deg C or higher for 0.1 sec or longer. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E001-A003-05 |
| Description: | Sub Thermistor (Rear) high temperature detection error |
| Causes: | The Sub Thermistor (Rear) detected 290 deg C or higher for 0.1 sec or longer. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E001-A004-05 |
| Description: | Fixing Main Thermistor high temperature detection error |
| Causes: | The Fixing Main Thermistor detected 270 deg C or higher. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E001-A005-05 |
| Description: | Sub Thermistor (Front) high temperature detection error |
| Causes: | The Sub Thermistor (Front) detected 295 deg C or higher. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E001-A006-05 |
| Description: | Sub Thermistor (Rear) high temperature detection error |
| Causes: | The Sub Thermistor (Rear) detected 295 deg C or higher. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E002-A001-05 |
| Description: | Fixing Main Thermistor temperature increase detection error |
| Causes: | The Fixing Main Thermistor detected a temperature increase of 1 deg C for less than 5 sec from turning ON the main power until start of PI control. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E002-A002-05 |
| Description: | Fixing Main Thermistor open circuit detection error |
| Causes: | The Fixing Main Thermistor detected a temperature of 40 deg C or lower for 3 sec or longer from turning ON the main power until start of PI control. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E002-A003-05 |
| Description: | Sub Thermistor (Front) open circuit detection error |
| Causes: | The Sub Thermistor (Front) detected a temperature of 40 deg C or lower for 3 sec or longer from turning ON the main power until start of PI control. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E002-A004-05 |
| Description: | Sub Thermistor (Rear) open circuit detection error |
| Causes: | The Sub Thermistor (Rear) detected a temperature of 40 deg C or lower for 3 sec or longer from turning ON the main power until start of PI control. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E003-A001-05 |
| Description: | Fixing Main Thermistor low temperature detection error (during printing) |
| Causes: | The Fixing Main Thermistor detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater is turned OFF) during printing. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E003-A002-05 |
| Description: | Sub Thermistor (Front) low temperature detection error |
| Causes: | The Sub Thermistor (Front) detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater is turned OFF) during printing. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E003-A003-05 |
| Description: | Sub Thermistor (Rear) low temperature detection error |
| Causes: | The Sub Thermistor (Rear) detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater is turned OFF) during printing. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E004-0001-05 |
| Description: | Fixing Drive Assembly circuit error |
| Causes: | A continuous error was detected in the communication between the DC Controller PCB used to control the startup of the Fixing Assembly and the Low-voltage Power Supply PCB. |
| Remedy: | [Related parts] - Harness between the Connector J208 of the Low Voltage Power Supply PCB and the Connector J103 on the DC Controller PCB - Low-voltage Power Supply PCB - DC Controller PCB(UN1) [Remedy] - If such a power source as private electric generator is used that results in a frequency out of the specified range, 43 Hz to 67 Hz, replace the power source with one having the specified value. - Disconnect and then connect the Low Voltage Power Supply PCB Connector J208 and the Connector J103 on the DC Controller PCB. - Replace the Low-voltage Power Supply PCB. - Replace the DC Controller PCB. |
| Error code: | E004-0002-05 |
| Description: | Main Thermistor and Sub Thermistor (Rear) disconnection detection error |
| Causes: | Connection could not be detected within 0.5 sec when power was supplied to the Fixing Heater. |
| Remedy: | [Related parts] R1.00 - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) - Fixing Assembly - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E009-0001-05 |
| Description: | Fixing pressure timeout error |
| Causes: | Signal of the Fixing Pressure Release Sensor could not be detected at pressure application operation of the Fixing Pressure Release Cam, and the operation was not completed within 4 sec from the start of counterclockwise rotation of the Fixing Motor. |
| Remedy: | [Related parts] R1.01 - Harness between the DC Controller PCB (UN04/J134) and the Fixing Drawer (DR01/J5401) - Harness between the Fixing Drawer (DR01/J5401) and the Fixing Pressure Release Sensor (PS13/J5403) - Harness between the DC Controller PCB (UN04/J135) and the Fixing Motor (M04/J5412) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Fixing Pressure Release Sensor (PS13) - Fixing Motor (M04) - Fixing Drive Unit - Fixing Assembly - Low Voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If periodic sound has occurred, check/replace the Fixing Assembly, Low-voltage Power Supply PCB, DC Controller PCB, and related harness. 2. If the Delivery Roller is rotating without noise, or if noise of the gear teeth being improperly meshed has occurred, check/replace the Fixing Drive Unit. 3. If the Delivery Roller is not rotating, check/replace the Fixing Motor, Fixing Drive Unit, Lowvoltage Power Supply PCB, DC Controller PCB, and related harness. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E009-0002-05 |
| Description: | Fixing disengagement timeout error |
| Causes: | Signal of the Fixing Pressure Release Sensor could not be detected at pressure release operation of the Fixing Pressure Release Cam, and the operation was not completed within 4 sec from the start of counterclockwise rotation of the Fixing Motor. |
| Remedy: | [Related parts] R1.01 - Harness between the DC Controller PCB (UN04/J134) and the Fixing Drawer (DR01/J5401) - Harness between the Fixing Drawer (DR01/J5401) and the Fixing Pressure Release Sensor (PS13/J5403) - Harness between the DC Controller PCB (UN04/J135) and the Fixing Motor (M04/J5412) - Harness between the Low-voltage Power Supply PCB (UN01/J315 and J322) and the DC Controller PCB (UN04/J20 and J22) - Fixing Pressure Release Sensor (PS13) - Fixing Motor (M04) - Fixing Drive Unit - Fixing Assembly - Low Voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If periodic sound has occurred, check/replace the Fixing Assembly, Low-voltage Power Supply PCB, DC Controller PCB, and related harness. 2. If the Delivery Roller is rotating without noise, or if noise of the gear teeth being improperly meshed has occurred, check/replace the Fixing Drive Unit. 3. If the Delivery Roller is not rotating, check/replace the Fixing Motor, Fixing Drive Unit, Lowvoltage Power Supply PCB, DC Controller PCB, and related harness. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E009-0003-05 |
| Description: | Fixing pressure retry error |
| Causes: | Signal of the Fixing Pressure Release Sensor could not be detected at pressure application operation of the Fixing Pressure Release Cam, and the operation was not completed within 3 times from the start of counterclockwise rotation of the Fixing Motor. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J134) and the Fixing Drawer (DR01/J5401) - Harness between the Fixing Drawer (DR01/J5401) and the Fixing Pressure Release Sensor (PS13/J5403) - Harness between the DC Controller PCB (UN04/J135) and the Fixing Motor (M04/J5412) - Fixing Pressure Release Sensor (PS13) - Fixing Motor (M04) - Fixing Drive Unit - Fixing Assembly - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. Be sure to preferentially check the Fixing Drive Unit. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRE |
| Error code: | E009-0004-05 |
| Description: | Fixing disengagement retry error |
| Causes: | Signal of the Fixing Pressure Release Sensor could not be detected at pressure release operation of the Fixing Pressure Release Cam, and the operation was not completed within 3 times from the start of counterclockwise rotation of the Fixing Motor. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J134) and the Fixing Drawer (DR01/J5401) - Harness between the Fixing Drawer (DR01/J5401) and the Fixing Pressure Release Sensor (PS13/J5403) - Harness between the DC Controller PCB (UN04/J135) and the Fixing Motor (M04/J5412) - Fixing Pressure Release Sensor (PS13) - Fixing Motor (M04) - Fixing Drive Unit - Fixing Assembly - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. Be sure to preferentially check the Fixing Drive Unit. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E009-0006-05 |
| Description: | Fixing pressure timeout error (during disengagement retry) |
| Causes: | At retry of disengagement operation of the Fixing Pressure Release Cam, the Fixing Pressure Release Sensor did not detect engagement state within 4 sec after the start of counterclockwise rotation of the Fixing Motor. |
| Remedy: | [Related parts] R1.01 - Harness between the DC Controller PCB (UN04/J134) and the Fixing Drawer (DR01/J5401) - Harness between the Fixing Drawer (DR01/J5401) and the Fixing Pressure Release Sensor (PS13/J5403) - Harness between the DC Controller PCB (UN04/J135) and the Fixing Motor (M04/J5412) - Fixing Pressure Release Sensor (PS13) - Fixing Motor (M04) - Fixing Drive Unit - Fixing Assembly - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. Be sure to preferentially check the Fixing Drive Unit. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E010-0001-05 |
| Description: | Bk Drum_ITB Motor error |
| Causes: | It did not become the specified speed for 500 consecutive msec although 1000 msec have passed from the startup of the Bk Drum_ITB Motor in the Main Drive Unit. (The detection timing varies depending on the paper feed conditions.) |
| Remedy: | [Related parts] R1.00 - Harness between the Bk Drum_ITB Motor (M02/J5702) and the DC Controller PCB (UN04/J140) - Fuse in the Low-voltage Power Supply PCB (UN01/FU14) - Bk Drum_ITB Motor (M02) - Main Drive Unit - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harnesses from the Bk Drum_ITB Motor to the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the Bk Drum_ITB Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Lowvoltage Power Supply PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E010-0002-05 |
| Description: | Bk Drum_ITB Motor error |
| Causes: | The specified speed could not be detected for 500 consecutive msec although it became the specified speed at least once from the startup of the Bk Drum_ITB Motor in the Main Drive Unit. |
| Remedy: | [Related parts] R1.00 - Harness between the Bk Drum_ITB Motor (M02/J5702) and the DC Controller PCB (UN04/J140) - Fuse in the Low-voltage Power Supply PCB (UN01/FU14) - Bk Drum_ITB Motor (M02) - Main Drive Unit - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harnesses from the Bk Drum_ITB Motor to the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the Bk Drum_ITB Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Lowvoltage Power Supply PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E010-0003-05 |
| Description: | Bk Drum_ITB Motor error |
| Causes: | There was no FG signal input for 300 msec from the startup of the Bk Drum_ITB Motor in the Main Drive Unit. |
| Remedy: | [Related parts] R1.00 - Harness between the Bk Drum_ITB Motor (M02/J5702) and the DC Controller PCB (UN04/J140) - Fuse in the Low-voltage Power Supply PCB (UN01/FU14) - Bk Drum_ITB Motor (M02) - Main Drive Unit - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harnesses from the Bk Drum_ITB Motor to the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the Bk Drum_ITB Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Lowvoltage Power Supply PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E012-0001-05 |
| Description: | CL Drum Motor error |
| Causes: | It did not become the specified speed for 500 consecutive msec although 1000 msec have passed from the startup of the CL Drum Motor in the Main Drive Unit. (The detection timing varies depending on the paper feed conditions.) |
| Remedy: | [Related parts] R1.00 - Harness between the CL Drum Motor (M01/J5701) and the DC Controller PCB (UN04/J140) - Fuse in the Low-voltage Power Supply PCB (UN01/FU14) - CL Drum Motor (M01) - Main Drive Unit - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the CL Drum Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the CL Drum Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Lowvoltage Power Supply PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E012-0002-05 |
| Description: | CL Drum Motor error |
| Causes: | The specified speed could not be detected for 500 consecutive msec although it became the specified speed at least once from the startup of the CL Drum Motor in the Main Drive Unit. |
| Remedy: | [Related parts] R1.00 - Harness between the CL Drum Motor (M01/J5701) and the DC Controller PCB (UN04/J140) - Fuse in the Low-voltage Power Supply PCB (UN01/FU14) - CL Drum Motor (M01) - Main Drive Unit - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the CL Drum Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the CL Drum Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Lowvoltage Power Supply PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E012-0003-05 |
| Description: | CL Drum Motor error |
| Causes: | There was no FG signal input for 300 msec from the startup of the CL Drum Motor in the Main Drive Unit. |
| Remedy: | [Related parts] R1.00 - Harness between the CL Drum Motor (M01/J5701) and the DC Controller PCB (UN04/J140) - Fuse in the Low-voltage Power Supply PCB (UN01/FU14) - CL Drum Motor (M01) - Main Drive Unit - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the CL Drum Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the Low-voltage Power Supply PCB using a tester. a. If power is flowing to it (the measurement value is less than 1 ohm), 1. Replace the CL Drum Motor. 2. Replace the DC Controller PCB. b. If the power is not flowing to it (the measurement value is 1 ohm or higher), replace the Lowvoltage Power Supply PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E014-0001-05 |
| Description: | Fixing Motor error |
| Causes: | An error is reported under any of the following conditions. (1) The ASIC detected that the motor did not rotate with its motor speed detection result never within the specified range since the Fixing Motor started rotation. (2) The motor speed detection result of the ASIC never fell within the specified range since the Fixing Motor started rotation and the ASIC detected for 2 consecutive seconds that the motor speed did not fall within the specified range . |
| Remedy: | [Related parts] - Harness between the Connector J56 of the Fixing Motor and the Connector J118 on the DC Controller PCB - Fixing Motor - DC Controller PCB(UN1) [Remedy] - Disconnect and then connect the Connector J56 of the Fixing Motor and the Connector J118 on the DC Controller PCB. - Perform the Fixing Motor drive test in service mode. Replace the Fixing Motor if it does not operate. Specify the motor to operate: COPIER > FUNCTION > PART-CHK > MTR Check the motor operation: COPIER > FUNCTION > PART-CHK > MTR-ON |
| Error code: | E014-0002-05 |
| Description: | Fixing Motor error |
| Causes: | An error is reported under any of the following conditions. (1) The ASIC detected that the motor did not rotate after the motor speed detection result of the ASIC fell within the specified range at least once during the rotation of the Fixing Motor. (2) The ASIC detected for 2 consecutive seconds that the motor speed did not fall within the specified range after the motor speed detection result of the ASIC fell within the specified range at least once during the rotation of the Fixing Motor. |
| Remedy: | [Related parts] - Harness between the Connector J56 of the Fixing Motor and the Connector J118 on the DC Controller PCB - Fixing Motor - DC Controller PCB(UN1) [Remedy] - Disconnect and then connect the Connector J56 of the Fixing Motor and the Connector J118 on the DC Controller PCB. - Perform the Fixing Motor drive test in service mode. Replace the Fixing Motor if it does not operate. Specify the motor to operate: COPIER > FUNCTION > PART-CHK > MTR Check the motor operation: COPIER > FUNCTION > PART-CHK > MTR-ON |
| Error code: | E014-0003-05 |
| Description: | Fixing Motor error |
| Causes: | There was no FG signal input for 300 msec from the startup of the Fixing Motor. (The detection timing varies depending on the paper feed conditions.) |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J135) and the Fixing Motor (M04/J5412) - Fuse in the DC Controller PCB (UN04/FU1) - Fixing Motor (M04) - Idler Gear in the Fixing Assembly - Pressure Roller Gear in the Fixing Assembly - Fixing Assembly - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Fixing Assembly is pushed into the host machine so the handle is locked and there is no backlash while it is installed. 2. Remove the Fixing Assembly, and rotate the Idler Gear and the Pressure Roller Gear by hand to check visually that there is no bent or missing teeth or abnormal abrasion (edge of the gear is no longer tooth-shaped). 3. Replace the Fixing Assembly. 4. Check the harness between the DC Controller PCB and the Fixing Motor. 5. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the Fixing Motor. 2. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRA |
| Error code: | E020-01A8-05 |
| Description: | ATR Sensor (Y) output error |
| Causes: | The output value of the ATR Sensor (Y) in the Drum Unit (Y) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times during printing. |
| Remedy: | [Related parts] R1.00 - Harness between the ATR Sensor (Y) (UN34/J6021) and the Drum Unit Memory PCB (Y) - Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (Y) (UN08/ J6001) - ATR Sensor (Y) (UN34) - Drum Unit (Y) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (Y) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-01B8-05 |
| Description: | ATR Sensor (Y) output error |
| Causes: | a. The output value of the ATR Sensor (Y) in the Drum Unit (Y) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times at initialization. b. The output value did not exceed 140 although the control voltage of the ATR Sensor (Y) in the Drum Unit (Y) was increased to 248 or higher, or it did not fall below 140 although the voltage was decreased to 8 at initialization. |
| Remedy: | [Related parts] R1.00 - Harness between the ATR Sensor (Y) (UN34/J6021) and the Drum Unit Memory PCB (Y) - Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (Y) (UN08/ J6001) - ATR Sensor (Y) (UN34) - Drum Unit (Y) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (Y) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-01C0-05 |
| Description: | Error in take-up of Sealing Member (Y) |
| Causes: | The patch output value (SigR) failed to be 230 or less during initialization of the Drum Unit (Y). |
| Remedy: | [Remedy] Check/replace the Drum Unit (Y). |
| Error code: | E020-01F0-05 |
| Description: | Error in toner density (Y) at communication failure of the Drum Unit Memory PCB (Y) |
| Causes: | Communication between the DC Controller PCB and the Drum Unit Memory PCB (Y) was not available, and the output value (SigR) of the ATR Sensor (Y) did not fall within the range from 50 or higher to 800 or less for 2 consecutive times. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (Y) (UN08/ J6001) - Drum Unit (Y) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (Y) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-02A8-05 |
| Description: | ATR Sensor (M) output error |
| Causes: | The output value of the ATR Sensor (M) in the Drum Unit (M) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times during printing. |
| Remedy: | [Related parts] R1.00 - Harness between the ATR Sensor (M) (UN35/J6022) and the Drum Unit Memory PCB (M) (UN13/ J6012) - Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (M) (UN09/ J6002) - ATR Sensor (M) (UN35) - Drum Unit (M) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (M) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-02B8-05 |
| Description: | ATR Sensor (M) output error |
| Causes: | a. The output value of the ATR Sensor (M) in the Drum Unit (M) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times at initialization. b. The output value did not exceed 140 although the control voltage of the ATR Sensor (M) in the Drum Unit (M) was increased to 248 or higher, or it did not fall below 140 although the voltage was decreased to 8 at initialization. |
| Remedy: | [Related parts] R1.00 - Harness between the ATR Sensor (M) (UN35/J6022) and the Drum Unit Memory PCB (M) (UN13/ J6012) - Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (M) (UN09/ J6002) - ATR Sensor (M) (UN35) - Drum Unit (M) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (M) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-02C0-05 |
| Description: | Error in take-up of Sealing Member (M) |
| Causes: | The patch output value (SigR) failed to be 230 or less during initialization of the Drum Unit (M). |
| Remedy: | [Remedy] Check/replace the Drum Unit (M). |
| Error code: | E020-02F0-05 |
| Description: | Error in toner density (M) at communication failure of the Drum Unit Memory PCB (M) |
| Causes: | Communication between the DC Controller PCB and the Drum Unit Memory PCB (M) was not available, and the output value (SigR) of the ATR Sensor (M) did not fall within the range from 50 or higher to 800 or less for 2 consecutive times. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J160) and the Drum Unit Relay PCB (M) (UN09/ J6002) - Drum Unit (M) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (M) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-03A8-05 |
| Description: | ATR Sensor (C) output error |
| Causes: | The output value of the ATR Sensor (C) in the Drum Unit (C) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times during printing. |
| Remedy: | [Related parts] R1.00 - Harness between the ATR Sensor (C) (UN36/J6023) and the Drum Unit Memory PCB (C) (UN14/ J6013) - Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (C) (UN10/ J6003) - ATR Sensor (C) (UN36) - Drum Unit (C) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (C) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-03B8-05 |
| Description: | ATR Sensor (C) output error |
| Causes: | a. The output value of the ATR Sensor (C) in the Drum Unit (C) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times at initialization. b. The output value did not exceed 140 although the control voltage of the ATR Sensor (C) in the Drum Unit (C) was increased to 248 or higher, or it did not fall below 140 although the voltage was decreased to 8 at initialization. |
| Remedy: | [Related parts] R1.00 - Harness between the ATR Sensor (C) (UN36/J6023) and the Drum Unit Memory PCB (C) (UN14/ J6013) - Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (C) (UN10/ J6003) - ATR Sensor (C) (UN36) - Drum Unit (C) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (C) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-03C0-05 |
| Description: | Error in take-up of Sealing Member (C) |
| Causes: | The patch output value (SigR) failed to be 900 or less during initialization of the Drum Unit (C). |
| Remedy: | [Remedy] Check/replace the Drum Unit (C). |
| Error code: | E020-03F0-05 |
| Description: | Error in toner density (C) at communication failure of the Drum Unit Memory PCB (C) |
| Causes: | Communication between the DC Controller PCB and the Drum Unit Memory PCB (C) was not available, and the output value (SigR) of the ATR Sensor (C) did not fall within the range from 50 or higher to 800 or less for 2 consecutive times. |
| Remedy: | [Related parts] - Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (Y) (UN10/ J6003) - Drum Unit (C) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (C) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-04A8-05 |
| Description: | ATR Sensor (Bk) output error |
| Causes: | The output value of the ATR Sensor (Bk) in the Drum Unit (Bk) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times during printing. |
| Remedy: | [Related parts] R1.00 - Harness between the ATR Sensor (Bk) (UN37/J6024) and the Drum Unit Memory PCB (Bk) (UN15/J6014) - Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (Bk) (UN11/ J6004) - ATR Sensor (Bk) (UN37) - Drum Unit (Bk) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (Bk) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-04B8-05 |
| Description: | ATR Sensor (Bk) output error |
| Causes: | a. The output value of the ATR Sensor (Bk) in the Drum Unit (Bk) did not fall within the range from 10 or higher to 990 or less for 2 consecutive times at initialization. b. The output value did not exceed 140 although the control voltage of the ATR Sensor (Bk) in the Drum Unit (Bk) was increased to 248 or higher, or it did not fall below 140 although the voltage was decreased to 8 at initialization. |
| Remedy: | [Related parts] R1.00 - Harness between the ATR Sensor (Bk) (UN37/J6024) and the Drum Unit Memory PCB (Bk) (UN15/J6014) - Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (Bk) (UN11/ J6004) - ATR Sensor (Bk) (UN37) - Drum Unit (Bk) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (Bk) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E020-04C0-05 |
| Description: | Error in take-up of Sealing Member (Bk) |
| Causes: | The patch output value (SigR) failed to be 900 or less during initialization of the Drum Unit (Bk). |
| Remedy: | [Remedy] Check/replace the Drum Unit (Bk). |
| Error code: | E020-04F0-05 |
| Description: | Error in toner density (Bk) at communication failure of the Drum Unit Memory PCB (Bk) |
| Causes: | Communication between the DC Controller PCB and the Drum Unit Memory PCB (Bk) was not available, and the output value (SigR) of the ATR Sensor (Bk) did not fall within the range from 50 or higher to 800 or less for 2 consecutive times. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J162) and the Drum Unit Relay PCB (Bk) (UN11/ J6004) - Drum Unit (Bk) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (Bk) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E021-0001-05 |
| Description: | Developing Disengagement Motor error |
| Causes: | Developer Alienation Sensor was not in the disengagement status after the end of the disengagement operation of the Developing Cylinder. |
| Remedy: | [Related parts] - Harness between the Connector J38 of the Developer Alienation Motor and the Connector J354 on the DC Controller PCB - Developer Alienation Motor - DC Controller PCB(UN1) - Main Drive Unit [Remedy] - Disconnect and then connect the Connector J38 of the Developer Alienation Motor and the Connector J354 of the DC Controller PCB. - Perform the Developer Alienation drive test in service mode. If the developer alienation motor does not operate, replace it. Specify the motor to operate: COPIER > FUNCTION > PART-CHK > MTR Check the motor operation: COPIER > FUNCTION > PART-CHK > MTR-ON - Check the condition of the Developer Home Position Sensor in service mode and replace the Main Drive Unit if it is abnormal. SITUATION > Sensor Check |
| Error code: | E021-0002-05 |
| Description: | Developing Motor error |
| Causes: | The specified speed could not be detected for 500 consecutive msec although it became the specified speed at least once from the startup of the Developing Motor. |
| Remedy: | [Related parts] R1.00 - Harness between the Developing Motor (M03/J5703) and the DC Controller PCB (UN04/J142) - Fuse in the DC Controller PCB (UN04/FU4) - Developing Motor (M03) - Main Drive Unit - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the Developing Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the Developing Motor. 2. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E021-0003-05 |
| Description: | Developing Motor error |
| Causes: | There was no FG signal input for 300 msec from the startup of the Developing Motor. |
| Remedy: | [Related parts] R1.00 - Harness between the Developing Motor (M03/J5703) and the DC Controller PCB (UN04/J142) - Fuse in the DC Controller PCB (UN04/FU4) - Developing Motor (M03) - Main Drive Unit - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check whether the gears of the Main Drive Unit can be rotated by hand. a. If they cannot be rotated, replace the Main Drive Unit. b. If they can be rotated, check the harness between the Developing Motor and the DC Controller PCB. 2. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the Developing Motor. 2. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E021-0120-05 |
| Description: | Developing Screw rotation detection error (Y) |
| Causes: | The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (Y) in the Drum Unit (Y) was 0.5 V or less. |
| Remedy: | [Related parts] R1.00 - Harness between the Drum Unit Relay PCB (Y) (UN08/J6001) and the DC Controller PCB (UN04/ J160) - Drum Unit Relay PCB (Y) (UN08) - Drum Unit Memory PCB (Y) (UN12) - Drum Unit (Y) - DC Controller PCB (UN04) - Main Drive Unit [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (Y) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E021-0220-05 |
| Description: | Developing Screw rotation detection error (M) |
| Causes: | The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (M) in the Drum Unit (M) was 0.5 V or less. |
| Remedy: | [Related parts] R1.00 - Harness between the Drum Unit Relay PCB (M) (UN09/J6002) and the DC Controller PCB (UN04/ J160) - Drum Unit Relay PCB (M) (UN09) - Drum Unit Memory PCB (M) (UN13) - Drum Unit (M) - DC Controller PCB (UN04) - Main Drive Unit [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (M) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E021-0320-05 |
| Description: | Developing Screw rotation detection error (C) |
| Causes: | The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (C) in the Drum Unit (C) was 0.5 V or less. |
| Remedy: | [Related parts] R1.00 - Harness between the Drum Unit Relay PCB (C) (UN10/J6003) and the DC Controller PCB (UN04/ J162) - Drum Unit Relay PCB (C) (UN10) - Drum Unit Memory PCB (C) - Drum Unit (C) - DC Controller PCB (UN04) - Main Drive Unit [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (C) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E021-0420-05 |
| Description: | Developing Screw rotation detection error (Bk) |
| Causes: | The difference between the maximum and the minimum of sampling values detected by the ATR Sensor (Bk) in the Drum Unit (Bk) was 0.5 V or less. |
| Remedy: | [Related parts] R1.00 - Harness between the Drum Unit Relay PCB (Bk) (UN11/J6004) and the DC Controller PCB (UN04/J162) - Drum Unit Relay PCB (Bk) (UN11) - Drum Unit Memory PCB (Bk) (UN15) - Drum Unit (Bk) - DC Controller PCB (UN04) - Main Drive Unit [Remedy] Perform the following in the order while checking whether the error is cleared. 1. If the Drum Unit Memory PCB (Bk) is soiled, clean it with a blower. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025-0110-05 |
| Description: | Bottle Motor (YM) error (Y) |
| Causes: | The Bottle Rotation Sensor (Y) did not detect rotation for 5 times in a row although 1.5 sec (2 sec in the case of right before replacement of the Toner Container) has passed after the Bottle Motor (YM) was turned ON. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J155) and the Bottle Motor (YM) (M09/J6301) - Harness between the DC Controller PCB (UN04/J151) and the Bottle Rotation Sensor (Y) (PS06/ J5301) - Bottle Rotation Sensor (Y) (PS06) - Bottle Drive Unit (YM) - Toner Container (Y) - Hopper Unit (Y) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [CAUTION] Be sure to turn over the Door Lock Lever when removing the Bottle Drive Unit (YM) and rotating the drive section by hand. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025-0168-05 |
| Description: | No toner detection error (Y) |
| Causes: | - The state without toner was detected although the recovery sequence was performed for 5 times after replacement of the Toner Container (Y). * - The recovery sequence was repeated with no toner in the container. * In platform V3.6 and later, error caused by this event will not occur. |
| Remedy: | [Related parts] R1.00 - Main Drive Unit - Hopper Unit (Y) - Toner Bottle Mount Unit (Y) - Drum Unit (Y) - Toner Container (Y) [Remedy] Be sure to perform the following procedure. 1. Shake the Toner Container 10 times, and then insert it into the host machine. 2. Check/replace the related harness/cable, connector and parts. [Reference] If a user inserts an empty Toner Container (Y) repeatedly, the error may occur. |
| Error code: | E025-0210-05 |
| Description: | Bottle Motor (YM) error (M) |
| Causes: | The Bottle Rotation Sensor (M) did not detect rotation for 5 times in a row although 1.5 sec (2 sec in the case of right before replacement of the Toner Container) has passed after the Bottle Motor (YM) was turned ON. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J155) and the Bottle Motor (YM) (M09/J6301) - Harness between the DC Controller PCB (UN04/J151) and the Bottle Rotation Sensor (M) (PS07/ J5302) - Bottle Rotation Sensor (M) (PS07) - Bottle Drive Unit (YM) - Toner Container (M) - Hopper Unit (M) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [CAUTION] Be sure to turn over the Door Lock Lever when removing the Bottle Drive Unit (YM) and rotating the drive section by hand. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025-0268-05 |
| Description: | No toner detection error (M) |
| Causes: | - The state without toner was detected although the recovery sequence was performed for 5 times after replacement of the Toner Container (M). * - The recovery sequence was repeated with no toner in the container. * In platform V3.6 and later, error caused by this event will not occur. |
| Remedy: | [Related parts] R1.00 - Main Drive Unit - Hopper Unit (M) - Toner Bottle Mount Unit (M) - Drum Unit (M) - Toner Container (M) [Remedy] Be sure to perform the following procedure. 1. Shake the Toner Container 10 times, and then insert it into the host machine. 2. Check/replace the related harness/cable, connector and parts. [Reference] If a user inserts an empty Toner Container (M) repeatedly, the error may occur. |
| Error code: | E025-0310-05 |
| Description: | Bottle Motor (CK) error (C) |
| Causes: | The Bottle Rotation Sensor (C) did not detect rotation for 5 times in a row although 1.5 sec (2 sec in the case of right before replacement of the Toner Container) has passed after the Bottle Motor (CK) was turned ON. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J155) and the Bottle Motor (CK) (M10/J6302) - Harness between the DC Controller PCB (UN04/J151) and the Bottle Rotation Sensor (M) (PS08/ J5303) - Bottle Rotation Sensor (C) (PS08) - Bottle Drive Unit (CK) - Toner Container (C) - Hopper Unit (C) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [CAUTION] Be sure to turn over the Door Lock Lever when removing the Bottle Drive Unit (CK) and rotating the drive section by hand. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025-0368-05 |
| Description: | No toner detection error (C) |
| Causes: | - The state without toner was detected although the recovery sequence was performed for 5 times after replacement of the Toner Container (C). * - The recovery sequence was repeated with no toner in the container. * In platform V3.6 and later, error caused by this event will not occur. |
| Remedy: | [Related parts] R1.00 - Main Drive Unit - Hopper Unit (C) - Toner Bottle Mount Unit (C) - Drum Unit (C) - Toner Container (C) [Remedy] Be sure to perform the following procedure. 1. Shake the Toner Container 10 times, and then insert it into the host machine. 2. Check/replace the related harness/cable, connector and parts. [Reference] If a user inserts an empty Toner Container (C) repeatedly, the error may occur. |
| Error code: | E025-0410-05 |
| Description: | Bottle Motor (CK) error (Bk) |
| Causes: | The Bottle Rotation Sensor (Bk) did not detect rotation for 5 times in a row although 1.5 sec (2 sec in the case of right before replacement of the Toner Container) has passed after the Bottle Motor (CK) was turned ON. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J155) and the Bottle Motor (CK) (M10/J6302) - Harness between the DC Controller PCB (UN04/J151) and the Bottle Rotation Sensor (Bk) (PS09/J5304) - Bottle Rotation Sensor (Bk) (PS09) - Bottle Drive Unit (CK) - Toner Container (Bk) - Hopper Unit (Bk) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [CAUTION] Be sure to turn over the Door Lock Lever when removing the Bottle Drive Unit (CK) and rotating the drive section by hand. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E025-0468-05 |
| Description: | No toner detection error (Bk) |
| Causes: | - The state without toner was detected although the recovery sequence was performed for 5 times after replacement of the Toner Container (Bk). * - The recovery sequence was repeated with no toner in the container. * In platform V3.6 and later, error caused by this event will not occur. |
| Remedy: | [Related parts] R1.00 - Main Drive Unit - Hopper Unit (Bk) - Toner Bottle Mount Unit (Bk) - Drum Unit (Bk) - Toner Container (Bk) [Remedy] Be sure to perform the following procedure. 1. Shake the Toner Container 10 times, and then insert it into the host machine. 2. Check/replace the related harness/cable, connector and parts. [Reference] If a user inserts an empty Toner Container (Bk) repeatedly, the error may occur. |
| Error code: | E029-5008-05 |
| Description: | Registration Patch Sensor (Front) light intensity error |
| Causes: | The background regular reflection output of the Registration Patch Sensor at the front side did not fall within the specified range for 2 consecutive times at initialization. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J170) and the Registration Patch Sensor Unit (Front) (UN31/J5603) - Registration Patch Sensor Unit (Front) (UN31) - Registration Patch Sensor Unit (Front) Shutter - Registration Shutter Solenoid (SL03) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. Check the background regular reflection output value (front) in COPIER (level 2)> DISPLAY> DENS> P-B-P-C. a. If the value is less than 10, 1. Check if the sensor window of the Registration Patch Sensor Unit (Front) is soiled. If it is soiled, clean it with a blower. 2. Check that the Registration Patch Sensor Unit (Front) Shutter is properly installed and it is not damaged or deformed. If it is deformed or damaged, replace the Registration Patch Sensor Unit (Front). 3. Check the operation of the Registration Shutter Solenoid. 3-1. If the Registration Shutter Solenoid moves, 3-1-1. Replace the Registration Patch Sensor Unit (Front). 3-1-2. Replace the DC Controller PCB. 3-2. If the solenoid does not move, replace the Registration Shutter Solenoid. b. If the value is above 250, 1. Check the harness between the Registration Patch Sensor Unit (Front) and the DC Controller PCB. 2. Replace the harness between the Registration Patch Sensor Unit (Front) and the DC Controller PCB. 3. Replace the Registration Patch Sensor Unit (Front). 4. Replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E029-7008-05 |
| Description: | Registration Patch Sensor (Rear) light intensity error |
| Causes: | The background regular reflection output of the Registration Patch Sensor at the rear side did not fall within the specified range for 2 consecutive times at initialization. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J170) and the Registration Patch Sensor Unit (Rear) (UN32/J5604) - Registration Patch Sensor Unit (Rear) (UN32) - Registration Patch Sensor Unit (Rear) Shutter - Registration Shutter Solenoid (SL03) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. Check the background regular reflection output value (rear) in COPIER (level 2)> DISPLAY> DENS> P-B-P-Y. a. If the value is less than 10, 1. Check if the sensor window of the Registration Patch Sensor Unit (Rear) is soiled. If it is soiled, clean it with a blower. 2. Check that the Registration Patch Sensor Unit (Rear) Shutter is properly installed and it is not damaged or deformed. If it is deformed or damaged, replace the Registration Patch Sensor Unit (Rear). 3. Check the operation of the Registration Shutter Solenoid. 3-1. If the Registration Shutter Solenoid moves, 3-1-1. Replace the Registration Patch Sensor Unit (Rear). 3-1-2. Replace the DC Controller PCB. 3-2. If the solenoid does not move, replace the Registration Shutter Solenoid. b. If the value is above 250, 1. Check the harness between the Registration Patch Sensor Unit (Rear) and the DC Controller PCB. 2. Replace the harness between the Registration Patch Sensor Unit (Rear) and the DC Controller PCB. 3. Replace the Registration Patch Sensor Unit (Rear). 4. Replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E073-0001-05 |
| Description: | Interlock error |
| Causes: | No detection of Interlock (24 V) although all the Doors (Front Cover and Right Cover) of the host machine were closed. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J24) and the Interlock Switch 2 (SW03) - Harness between the DC Controller PCB (UN04/J20) and the Low-voltage Power Supply PCB (UN01/J315) - Front Cover/Right Cover - Low-voltage Power Supply PCB (UN01) - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Front Cover/Right Cover is closed. 2. Visually check that the Interlock Switch 2 are turned ON/OFF by opening/closing the Front Cover/Right Cover. 3. Check that the harness between the Interlock Switch 2 and the DC Controller PCB is not shortcircuited (the harness does not come in contact with the plate while the cable sheath is peeled). 4. Disconnect the connector (J24) of the DC Controller while the Front Cover and the Right Cover are closed, and measure the resistance value between the connectors J24/1-pin and the J24/3- pin on the J24 harness side using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the DC Controller PCB. 2. Replace the Low-voltage Power Supply PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the harness between the Interlock Switch 2 and the DC Controller PCB. 5. Check the harness between the Low-voltage Power Supply PCB and the DC Controller PCB. 6. Replace the DC Controller PCB. 7. Replace the Low-voltage Power Supply PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E074-0000-05 |
| Description: | Primary Transfer Roller disengagement control error |
| Causes: | Signal was not detected although the ITB Pressure Release Switch was turned ON/OFF for 6 times. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J162) and the ITB Pressure Release Switch (SW07/J6005) - Harness between the DC Controller PCB (UN04/J140) and the Primary Transfer Separation Solenoid (SL01/J5708) - Fuse in the DC Controller PCB (UN04/FU07) - ITB Guide Rail - Main Drive Unit - ITB Unit - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the ITB Unit is installed in the machine. 2. Replace the ITB Unit. 3. Check the harness between the DC Controller PCB and the ITB Pressure Release Switch. 4. Check the harness between the DC Controller PCB and the Primary Transfer Separation Solenoid. 5. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the ITB Guide Rail (Front/Rear). 2. Replace the Main Drive Unit. 3. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E074-0002-05 |
| Description: | Error in Primary Transfer Roller operation |
| Causes: | The ITB Pressure Release Switch could not detect the engagement operation within the specified period of time at engagement operation of the Primary Transfer Roller. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J162) and the ITB Pressure Release Switch (SW07/J6005) - Harness between the DC Controller PCB (UN04/J140) and the Primary Transfer Separation Solenoid (SL01/J5708) - Fuse in the DC Controller PCB (UN04/FU07) - ITB Guide Rail - Main Drive Unit - ITB Unit - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the ITB Unit is installed in the machine. 2. Replace the ITB Unit. 3. Check the harness between the DC Controller PCB and the ITB Pressure Release Switch. 4. Check the harness between the DC Controller PCB and the Primary Transfer Separation Solenoid. 5. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the ITB Guide Rail (Front/Rear). 2. Replace the Main Drive Unit. 3. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E100-0001-05 |
| Description: | BD error |
| Causes: | The BD lock was unlocked although it had been locked once. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) - Flexible Cable between the Main Controller PCB (UN81/J7002) and the Y/M/C/Bk Laser Driver PCB (UN05/J201) - Interlock Switch 2 (SW03) - Front Cover/Right Cover - Y/M/C/Bk Laser Driver PCB (UN05) - Laser Scanner Unit - DC Controller PCB (UN04) - Main Controller PCB (UN81) - Low Voltage Power Supply PCB (UN01) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After replacement of the Laser Driver PCB, execute "Settings/Registration> Adjustment/ Maintenance> Adjust Image Quality> Auto Correct Color Mismatch". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E102-0001-05 |
| Description: | EEPROM error |
| Causes: | An error has occurred in EEPROM of the Laser Scanner. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) - Flexible Cable between the Main Controller PCB (UN81/J7002) and the Y/M/C/Bk Laser Driver PCB (UN05/J201) - Interlock Switch 2 (SW03) - Y/M/C/Bk Laser Driver PCB (UN05) - Laser Scanner Unit - DC Controller PCB (UN04) - Main Controller PCB (UN81) - Low Voltage Power Supply PCB (UN01) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After replacement of the Laser Driver PCB, execute "Settings/Registration> Adjustment/ Maintenance> Adjust Image Quality> Auto Correct Color Mismatch". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E110-0001-05 |
| Description: | Scanner Motor error |
| Causes: | The Scanner Motor speed detection result of the ASIC did not fall within the specified range even after 5 seconds since the Scanner Motor started operation during the Scanner Motor startup. |
| Remedy: | [Related parts] - Harnesses connecting the Laser Scanner Unit, the Relay Connector J91, and the Connector J123 on the DC Controller PCB - Laser Scanner Unit - DC Controller PCB(UN1) [Remedy] - Disconnect and then connect the Relay Connector J91 from the Laser Scanner Unit and the Connector J123 on the DC Controller PCB. - If the error is not cleared, replace the Laser Scanner Unit. |
| Error code: | E110-0002-05 |
| Description: | Scanner Motor error |
| Causes: | An error is reported under any of the following conditions. (1) The Scanner Motor speed detection result of the ASIC did not fall within the range of target speed +/- 1.56% for 200 consecutive ms during the rotation of the Scanner Motor and after the Scanner Motor speed detection result of the ASIC fell within the specified range at least once. (2) The ASIC showed BD Error Bit 1 during the period before the start of masking in the vertical scanning direction after the release of masking in the feed direction while printing, measured the BD signal cycle 200 ms later, and the measured value did not return within the range of the target speed +/- 1.56%. |
| Remedy: | [Related parts] - Harnesses connecting the Laser Scanner Unit, the Relay Connector J91, and the Connector J123 on the DC Controller PCB - Laser Scanner Unit - DC Controller PCB(UN1) [Remedy] - Disconnect and then connect the Relay Connector J91 from the Laser Scanner Unit and the Connector J123 on the DC Controller PCB. - If the error is not cleared, replace the Laser Scanner Unit. |
| Error code: | E110-0003-05 |
| Description: | Scanner Motor error |
| Causes: | The phase was not locked by BD control within 10 sec after startup of Scanner Motor. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) - Flexible Cable between the Main Controller PCB (UN81/J7002) and the Y/M/C/Bk Laser Driver PCB (UN05/J201) - Interlock Switch 2 (SW03) - Front Cover/Right Cover - Y/M/C/Bk Laser Driver PCB (UN05) - Laser Scanner Unit - DC Controller PCB (UN04) - Main Controller PCB (UN81) - Low Voltage Power Supply PCB (UN01) [Remedy] 1. Check/replace the related harness/cable, connector and parts. 2. After replacement of the Laser Driver PCB, execute "Settings/Registration> Adjustment/ Maintenance> Adjust Image Quality> Auto Correct Color Mismatch". [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E110-0005-05 |
| Description: | Scanner Motor error |
| Causes: | GBD signal was not detected although a specified period of time had passed after startup. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J112) and the Main Controller PCB (UN81/ J4511) - Main Controller PCB (UN81) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E193-0000-05 |
| Description: | Communication error |
| Causes: | NACK was received twice at communication retry of image ASIC. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J112) and the Main Controller PCB (UN81/ J4511) - Main Controller PCB (UN81) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E193-0101-05 |
| Description: | Communication error |
| Causes: | There was no response at communication retry of image ASIC. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J112) and the Main Controller PCB (UN81/ J4511) - Main Controller PCB (UN81) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E193-0F00-05 |
| Description: | Communication error |
| Causes: | Image ASIC could not be sent due to insufficient software memory. |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E196-0000-05 ... E196-0102-05 |
| Description: | EEPROM communication error |
| Causes: | The NACK (a negative reply sent by the reception side to the sending side) was received for 3 times in communication from the DC Controller PCB (CPU) to the DCON EEPROM on the DC Controller PCB. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) - Harness between the DC Controller PCB (UN04/J184) and the Developing High-voltage PCB (UN06/J241) - Y/M/C/Bk Laser Driver PCB (UN05) - Developing High-voltage PCB (UN06) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E196-010F-05 |
| Description: | EEPROM communication error |
| Causes: | The number of read/write job data to the SCNR EEPROM (device information) exceeded 100. |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E196-020F-05 ... E196-050F-05 |
| Description: | EEPROM communication error |
| Causes: | The number of read/write job data (device information) to the PCRG (Y) EEPROM exceeded the specified value. |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E196-0800-05 ... E196-0802-05 |
| Description: | EEPROM communication error |
| Causes: | The NACK (a negative reply sent by the reception side to the sending side) was received for 3 times in communication from the DC Controller PCB (CPU) to the HVT EEPROM. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J110) and the Y/M/C/Bk Laser Driver PCB (UN05/J202) - Harness between the DC Controller PCB (UN04/J184) and the Developing High-voltage PCB (UN06/J241) - Y/M/C/Bk Laser Driver PCB (UN05) - Developing High-voltage PCB (UN06) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E196-080F-05 |
| Description: | EEPROM communication error |
| Causes: | The number of read/write job data to the HVT EEPROM (device information) exceeded 100. |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E196-090F-05 |
| Description: | EEPROM communication error |
| Causes: | The number of read/write job data (device information) to the PCRG (Bk) EEPROM exceeded the specified value. |
| Remedy: | [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power. |
| Error code: | E197-0000-05 ... E197-0F00-05 |
| Description: | Communication error |
| Causes: | Although access to KONA1 (ASIC) in the DC Controller PCB from the DC Controller PCB (CPU) was performed, the NACK (a negative reply sent by the reception side to the sending side) was received for 2 times. |
| Remedy: | [Remedy] Check/replace the DC Controller PCB (UN04). [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197-1000-05 |
| Description: | Communication error |
| Causes: | Although access to KONA2 (ASIC) in the DC Controller PCB from the DC Controller PCB (CPU) was performed, the NACK (a negative reply sent by the reception side to the sending side) was received for 2 times. |
| Remedy: | [Remedy] Check/replace the DC Controller PCB (UN04). [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197-1101-05 |
| Description: | Communication error |
| Causes: | Timeout error was detected at load control ASIC communication. (KONA2) |
| Remedy: | [Remedy] Check/replace the DC Controller PCB (UN04). [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197-1F00-05 |
| Description: | Communication error |
| Causes: | Although access to KONA2 (ASIC) in the DC Controller PCB from the DC Controller PCB (CPU) was performed, no response was received and timeout occurred. |
| Remedy: | [Remedy] Check/replace the DC Controller PCB (UN04). [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197-2000-05 |
| Description: | Communication error |
| Causes: | Although access to KONA3 (ASIC) in the Cassette Module Controller PCB from the DC Controller PCB (CPU) was performed, the NACK (a negative reply sent by the reception side to the sending side) was received for 3 times. |
| Remedy: | [Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN04/J190), the Drawer Unit (DR03/J5904) and the Cassette Module Controller PCB - Fuse in the DC Controller PCB (UN04/FU19) - Cassette Module Controller PCB - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. Check the harness between the DC Controller PCB and the cassette unit drawer on the host machine side. 3. Visually check if the cassette unit drawer on the host machine side and the drawer on the cassette unit side are damaged or if there is any bent pin. If so, replace the drawer. 4. Check the harness between the drawer on the cassette unit side and the Cassette Module Controller PCB. 5. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the Cassette Module Controller PCB. 2. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197-2101-05 |
| Description: | Communication error |
| Causes: | Although access to KONA3 (ASIC) in the Cassette Module Controller PCB from the DC Controller PCB (CPU) was performed, no response was received and timeout occurred. |
| Remedy: | [Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN04/J190), the Drawer Unit (DR03/J5904) and the Cassette Module Controller PCB - Fuse in the DC Controller PCB (UN04/FU19) - Cassette Module Controller PCB - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. Check the harness between the DC Controller PCB and the cassette unit drawer on the host machine side. 3. Visually check if the cassette unit drawer on the host machine side and the drawer on the cassette unit side are damaged or if there is any bent pin. If so, replace the drawer. 4. Check the harness between the drawer on the cassette unit side and the Cassette Module Controller PCB. 5. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the Cassette Module Controller PCB. 2. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E197-2F00-05 |
| Description: | Communication error |
| Causes: | Although access to KONA3 (ASIC) in the Cassette Module Controller PCB from the DC Controller PCB (CPU) was performed, no response was received and timeout occurred. |
| Remedy: | [Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN04/J190), the Drawer Unit (DR03/J5904) and the Cassette Module Controller PCB - Fuse in the DC Controller PCB (UN04/FU19) - Cassette Module Controller PCB - DC Controller PCB (UN04) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. Check the harness between the DC Controller PCB and the cassette unit drawer on the host machine side. 3. Visually check if the cassette unit drawer on the host machine side and the drawer on the cassette unit side are damaged or if there is any bent pin. If so, replace the drawer. 4. Check the harness between the drawer on the cassette unit side and the Cassette Module Controller PCB. 5. Measure the both ends of the fuse in the DC Controller PCB using a tester. a. If the measurement value is less than 1 ohm (conduction state), 1. Replace the Cassette Module Controller PCB. 2. Replace the DC Controller PCB. b. If the measurement value is 1 ohm or higher (non conduction state), replace the DC Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E202-0001-04 |
| Description: | Scanner Unit HP error |
| Causes: | The HP of the Scanner Unit could not be detected when starting scanning operation. |
| Remedy: | [Related parts] R1.00 - Harness between the CIS HP Sensor (J4205) and the Main Controller PCB (UN6/J4005) - Harness between the Reader Motor (J4305) and the Main Controller PCB (UN6/J4005) - Harness between the Main Controller PCB (UN6/J4509) and the Low-voltage Power Supply PCB (UN01/J313) - CIS HP Sensor - Reader Motor - Low-voltage Power Supply PCB (UN01) - Reader Assembly - Main Controller PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. At initial operation of the Reader startup after the main power is turned ON, check if the Reader Motor operates (whether the Scanner Unit moves or operation sound is heard). If it operates, check whether load on the Timing Belt for moving CIS is appropriate. a. If it is appropriate, replace the CIS HP Sensor. b. If it is not appropriate (overloaded), check/replace the Timing Belt, Drive Gear and pulley. 2. Check/replace the CIS Holder (soiling or damage on the surface). 3. Check/replace the related harness/cable, connector and parts. |
| Error code: | E202-0002-04 |
| Description: | Scanner Unit HP error |
| Causes: | The HP of the Scanner Unit could not be detected when completing scanning operation. |
| Remedy: | [Related parts] R1.00 - Harness between the CIS HP Sensor (J4205) and the Main Controller PCB (UN6/J4005) - Harness between the Reader Motor (J4305) and the Main Controller PCB (UN6/J4005) - Harness between the Main Controller PCB (UN6/J4509) and the Low-voltage Power Supply PCB (UN01/J313) - CIS HP Sensor - Reader Motor - Low-voltage Power Supply PCB (UN01) - Reader Assembly - Main Controller PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. At initial operation of the Reader startup after the main power is turned ON, check if the Reader Motor operates (whether the Scanner Unit moves or operation sound is heard). If it operates, check whether load on the Timing Belt for moving CIS is appropriate. a. If it is appropriate, replace the CIS HP Sensor. b. If it is not appropriate (overloaded), check/replace the Timing Belt, Drive Gear and pulley. 2. Check/replace the CIS Holder (soiling or damage on the surface). 3. Check/replace the related harness/cable, connector and parts. |
| Error code: | E227-0001-04 |
| Description: | Power supply error |
| Causes: | The Main Controller PCB did not detect 24 V when the main power was turned ON. |
| Remedy: | [Related parts] R1.00 - Harness between the Main Controller PCB (UN6/J4509) and the Low-voltage Power Supply PCB (UN01/J313) - Low-voltage Power Supply PCB (UN01) - Main Controller PCB (UN6) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E240-0000-05 |
| Description: | Controller communication error |
| Causes: | A communication error occurred between the Main Controller PCB and the DC Controller PCB. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J112) and the Main Controller PCB (UN81/ J4511) - DC Controller PCB (UN04) - Main Controller PCB (UN81) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the harness between the DC Controller PCB and the Main Controller PCB. 2. Turn ON the power, and check if the initialization is executed at startup. 2-1. If the initialization is not executed, replace the DC Controller PCB. 2-2. If the initialization is executed, replace the Main Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E240-0002-00 |
| Description: | Controller communication error |
| Causes: | An error in receiving data from the controller was detected. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN1/J112) and the Main Controller PCB (UN6/J4511) - DC Controller PCB (UN1) - Main Controller PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the harness between the DC Controller PCB and the Main Controller PCB. 2. Turn ON the power, and check if the initialization is executed at startup. 2-1. If the initialization is not executed, replace the DC Controller PCB. 2-2. If the initialization is executed, replace the Main Controller PCB. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E246-0001-00 ... E246-0005-00 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E247-0001-00 ... E247-0004-00 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E248-0001-04 |
| Description: | Reader backup error |
| Causes: | Reading error was detected when the Controller IC of the Main Controller PCB read the Reader backup value in the Flash PCB. |
| Remedy: | [Related parts] R1.00 - Flash PCB (UN91) - Main Controller PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. After performing the remedy, enter the value of the service label again. 1. After executing "COPIER> FUNCTION> CLEAR> R-CON", turn OFF and then ON the main power, and check whether the error is cleared. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 3. Replace the Main Controller PCB. |
| Error code: | E248-0002-04 |
| Description: | Reader backup error |
| Causes: | The Controller IC of the Main Controller PCB failed to rewrite the Reader backup value in the Flash PCB. |
| Remedy: | [Related parts] R1.00 - Flash PCB (UN91) - Main Controller PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. After performing the remedy, enter the value of the service label again. 1. After executing "COPIER> FUNCTION> CLEAR> R-CON", turn OFF and then ON the main power, and check whether the error is cleared. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 3. Replace the Main Controller PCB. |
| Error code: | E280-0001-04 |
| Description: | Scanner Unit communication error |
| Causes: | Communication between the Main Controller and the Scanner Unit (front) was not started within the specified period of time. |
| Remedy: | [Related parts] R1.00 - Harness between the Scanner Unit_(UN68) and the Main Controller PCB (UN6) - Scanner Unit_front(UN68) - Main Controller PCB (UN6) - DC Controller PCB (UN1) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E280-0002-04 |
| Description: | Scanner Unit communication error |
| Causes: | Disconnection of FFC between the Main Controller and the Scanner Unit (front) was detected. |
| Remedy: | [Related parts] R1.00 - Harness between the Scanner Unit_front)(UN68) and the Main Controller PCB (UN6) - Scanner Unit _front(UN68) - Main Controller PCB (UN6) - DC Controller PCB (UN1) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E280-0101-04 |
| Description: | Scanner Unit communication error |
| Causes: | Communication between the Main Controller and the Scanner Unit (back) was not started within the specified period of time. |
| Remedy: | [Related parts] R1.00 - Harness between the Scanner Unit (back) and the Main Controller PCB (UN6) - Scanner Unit (back) - ADF UNIT - Main Controller PCB (UN6) - DC Controller PCB (UN1) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E280-0102-04 |
| Description: | Scanner Unit communication error |
| Causes: | Disconnection of FFC between the Main Controller and the Scanner Unit (back) was detected. |
| Remedy: | [Related parts] R1.00 - Harness between the Scanner Unit (back) and the Main Controller PCB (UN6) - Scanner Unit (back) - ADF UNIT - Main Controller PCB (UN6) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E302-0001-04 ... E302-0103-04 |
| Description: | Error in paper front white shading |
| Causes: | An error in the shading value was detected at white shading. |
| Remedy: | [Related parts] R1.00 - Harness between the Scanner Unit (front) and the Main Controller PCB (UN81) - Scanner Unit (front) - Main Controller PCB (UN81) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E315-0007-00 ... E315-0510-00 |
| Description: | Image process device timeout error |
| Causes: | Image compression process was not completed within the specified period of time at scanning. |
| Remedy: | [Related parts] R1.00 - Harness between the Reader Unit and Main Controller PCB - Main Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Reinstall the latest system software using SST or a USB flash drive. 2. Check/replace the related harness/cable, connector and parts. |
| Error code: | E315-0530-00 |
| Description: | Image process device error |
| Causes: | Compression processing of the scanned image into JPEG was terminated abnormally. |
| Remedy: | [Related parts] - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Reinstall the latest system software using SST or a USB flash drive. 2. Check/replace the Main Controller PCB. |
| Error code: | E315-0531-00 |
| Description: | Image process device timeout error |
| Causes: | Compression processing of the scanned image into JPEG was not completed within the specified period of time. |
| Remedy: | [Related parts] R1.00 - Harness between the Reader Unit and Main Controller PCB - Main Controller PCB(UN6) - Reader Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Reinstall the latest system software using SST or a USB flash drive. 2. Check/replace the related harness/cable, connector and parts. |
| Error code: | E315-0540-00 |
| Description: | Image process device error |
| Causes: | An error occurred during decompression of JPEG. |
| Remedy: | [Related parts] - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Reinstall the latest system software using SST or a USB flash drive. 2. Check/replace the Main Controller PCB. |
| Error code: | E315-0541-00 |
| Description: | Image process device timeout error |
| Causes: | Decompression of JPEG was not completed within the specified period of time. |
| Remedy: | [Related parts] - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Reinstall the latest system software using SST or a USB flash drive. 2. Check/replace the Main Controller PCB. |
| Error code: | E350-0000-00 ... E350-3000-00 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E351-0000-00 |
| Description: | System error |
| Causes: | Main Controller PCB communication error. |
| Remedy: | [Related parts] - Main Controller PCB(UN6) [Remedy] Check/replace the Main Controller PCB (UN6) |
| Error code: | E354-0001-00 ... E355-0004-00 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E412-0005-04 |
| Description: | Fan error |
| Causes: | Stop of fan was detected after rotation signal for the ADF Cooling Fan was transmitted. |
| Remedy: | [Related parts] R1.00 - ADF Cooling Fan - Main Controller PCB (UN6) [Remedy] Check/replace the related parts. |
| Error code: | E412-0006-04 |
| Description: | Fan error |
| Causes: | Rotation of fan was detected after the stop signal for the ADF Cooling Fan was transmitted. |
| Remedy: | [Related parts] R1.00 - ADF Cooling Fan(FM4100) - Main Controller PCB (UN6) - DC Controller PCB (UN1) [Remedy] Check/replace the related parts. After performing the remedy, |
| Error code: | E423-0001-04 |
| Description: | ADF error |
| Causes: | An access error to SDRAM for controlling ADF that is installed on the Main Controller PCB was detected. |
| Remedy: | [Related parts] - Main Controller PCB(UN6) [Remedy] Check/replace the Main Controller PCB (UN6) |
| Error code: | E500-0000-02 |
| Description: | Finisher communication error |
| Causes: | An error was detected on the finisher side. |
| Remedy: | 1. Check that the connector (CN1/P3/J3) of the Interface Harness is not disconnected. 2. Replace the Finisher Controller PCB. 3. Replace the Interface Harness. |
| Error code: | E530-0001-02 |
| Description: | Front Alignment Plate HP Sensor error |
| Causes: | The Front Alignment Motor did not move from the HP. |
| Remedy: | 1. Check that the connector (P8-3/P8/J8) of the Front Alignment Plate HP Sensor (S4) is not disconnected. 2. Check that the connector (P6-12/P6-2/J6-2/P6/J6) of the Front Alignment Motor (M4) is not disconnected. 3. Replace the Front Alignment Plate HP Sensor (S4). 4. Replace the Front Alignment Motor (M4). 5. Check the conditions of the front alignment drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E530-0002-02 |
| Description: | Front Alignment Motor error |
| Causes: | The Front Alignment Motor did not return to the HP. |
| Remedy: | 1. Check that the connector (P8-3/P8/J8) of the Front Alignment Plate HP Sensor (S4) is not disconnected. 2. Check that the connector (P6-12/P6-2/J6-2/P6/J6) of the Front Alignment Motor (M4) is not disconnected. 3. Replace the Front Alignment Plate HP Sensor (S4). 4. Replace the Front Alignment Motor (M4). 5. Check the conditions of the front alignment drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E531-8001-02 |
| Description: | Staple home position error |
| Causes: | If the Staple Ready Sensor detects OFF at the end of staple repositioning, perform staple repositioning again. If the Staple Ready Sensor detects OFF after performing staple repositioning for 11 times, a staple repositioning error is reported. |
| Remedy: | [Related parts] - Harness between the Connector J6 on the Stapler Unit and the Connector J203 on the Finisher Controller PCB - Harness between the Connector J26 on the Stapler Unit and the Connector J204 on the Finisher Controller PCB - Replace the Stapler Unit [Remedy] - Remove and then install the staple cartridge. - Disconnect and then connect the Connectors J6 and J26 on the Stapler Unit and the Connectors J203 and J204 on the Finisher Controller PCB. - Replace the Stapler Unit. |
| Error code: | E531-8002-02 |
| Description: | Staple home position error |
| Causes: | When the Staple Home Position Sensor does not detect the home position within 600 ms from the time when the Staple Motor started operation, if it does not detect the home position within 600 msec of counterclockwise motor rotation after stopping the motor for 1000 msec, the Staple Motor is determined to be faulty. |
| Remedy: | [Related parts] - Harness between the Connector J6 on the Stapler Unit and the Connector J203 on the Finisher Controller PCB - Harness between the Connector J26 on the Stapler Unit and the Connector J204 on the Finisher Controller PCB - Replace the Stapler Unit [Remedy] - Disconnect and then connect the Connectors J6 and J26 on the Stapler Unit and the Connectors J203 and J204 on the Finisher Controller PCB. - Replace the Stapler Unit. |
| Error code: | E537-0001-02 |
| Description: | Rear Alignment Motor error |
| Causes: | The Rear Alignment Motor did not move from the HP. |
| Remedy: | 1. Check that the connector (P7-5/P7/J7) of the Rear Alignment Plate HP Sensor (S5) is not disconnected. 2. Check that the connector (P5-13/P5-3/J5-3/P5/J5) of the Rear Alignment Motor (M5) is not disconnected. 3. Replace the Rear Alignment Plate HP Sensor (S5). 4. Replace the Rear Alignment Motor (M5). 5. Check the conditions of the rear alignment drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E537-0002-02 |
| Description: | Rear Alignment Motor error |
| Causes: | The Rear Alignment Motor did not return to the HP. |
| Remedy: | 1. Check that the connector (P7-5/P7/J7) of the Rear Alignment Plate HP Sensor (S5) is not disconnected. 2. Check that the connector (P5-13/P5-3/J5-3/P5/J5) of the Rear Alignment Motor (M5) is not disconnected. 3. Replace the Rear Alignment Plate HP Sensor (S5). 4. Replace the Rear Alignment Motor (M5). 5. Check the conditions of the rear alignment drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E540-0001-02 |
| Description: | Stack Tray Shift Motor timeout |
| Causes: | Timeout |
| Remedy: | 1. Check that the connector (P8-11/P8-1/J8-1/J8) of the Stack Tray Paper Height Sensor (S9) is not disconnected. 2. Check that the connector (J14-3/P14-3/P14/J14) of the Stack Tray Shift Motor (M8) is not disconnected. 3. Replace the Stack Tray Paper Height Sensor (S9). 4. Replace the Stack Tray Shift Motor (M8). 5. Check the conditions of the stack tray shift motor drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E575-0001-02 |
| Description: | Gripper Motor error |
| Causes: | The Gripper Motor did not move from the HP. |
| Remedy: | 1. Check that the connector (P7-14/P7-6/J7-6/P7/J7) of the Gripper HP Sensor (S7) is not disconnected. 2. Check that the connector (P6-3/J6-3/P6/J6) of the Gripper Motor (M7) is not disconnected. 3. Replace the Gripper HP Sensor (S7). 4. Replace the Gripper Motor (M7). 5. Check the conditions of the gripper drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E575-0002-02 |
| Description: | Gripper Motor error |
| Causes: | The Gripper Motor did not return to the HP. |
| Remedy: | 1. Check that the connector (P7-14/P7-6/J7-6/P7/J7) of the Gripper HP Sensor (S7) is not disconnected. 2. Check that the connector (P6-3/J6-3/P6/J6) of the Gripper Motor (M7) is not disconnected. 3. Replace the Gripper HP Sensor (S7). 4. Replace the Gripper Motor (M7). 5. Check the conditions of the gripper drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E575-0004-02 |
| Description: | Gripper clock error |
| Causes: | Clock error |
| Remedy: | 1. Check that the connector (P13-1/P13/J13) of the Gripper Encoder Sensor (S8) is not disconnected. 2. Replace the Gripper Encoder Sensor (S8). |
| Error code: | E577-0001-02 |
| Description: | Paddle Motor error |
| Causes: | The Paddle Motor did not move from the HP. |
| Remedy: | 1. Check that the connector (P8-4/P8/J8) of the Paddle HP Sensor (S3) is not disconnected. 2. Check that the connector (P5-4/P5/J5) of the Paddle Motor (M3) is not disconnected. 3. Replace the Paddle HP Sensor (S3). 4. Replace the Paddle Motor (M3). 5. Check the conditions of the paddle drive parts (gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E577-0002-02 |
| Description: | Paddle Motor error |
| Causes: | The Paddle Motor did not return to the HP. |
| Remedy: | 1. Check that the connector (P8-4/P8/J8) of the Paddle HP Sensor (S3) is not disconnected. 2. Check that the connector (P5-4/P5/J5) of the Paddle Motor (M3) is not disconnected. 3. Replace the Paddle HP Sensor (S3). 4. Replace the Paddle Motor (M3). 5. Check the conditions of the paddle drive parts (gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E583-0001-02 |
| Description: | Tray Auxiliary Guide Motor error |
| Causes: | The Tray Auxiliary Guide Motor did not move from the HP. |
| Remedy: | 1. Check that the connector (P8-12/P8-2/J8-2/P8/J8) of the Tray Auxiliary Guide HP Sensor (S6) is not disconnected. 2. Check that the connector (P6-1/P6/J6) of the Tray Auxiliary Guide Motor (M6) is not disconnected. 3. Replace the Tray Auxiliary Guide HP Sensor (S6). 4. Replace the Tray Auxiliary Guide Motor (M6). 5. Check the conditions of the tray auxiliary guide drive parts (gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E583-0002-02 |
| Description: | Tray Auxiliary Guide Motor error |
| Causes: | The Tray Auxiliary Guide Motor did not return to the HP. |
| Remedy: | 1. Check that the connector (P8-12/P8-2/J8-2/P8/J8) of the Tray Auxiliary Guide HP Sensor (S6) is not disconnected. 2. Check that the connector (P6-1/P6/J6) of the Tray Auxiliary Guide Motor (M6) is not disconnected. 3. Replace the Tray Auxiliary Guide HP Sensor (S6). 4. Replace the Tray Auxiliary Guide Motor (M6). 5. Check the conditions of the tray auxiliary guide drive parts (gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly. |
| Error code: | E602-0001-00 |
| Description: | HDD error |
| Causes: | HDD failed to be Ready, or HDD was not formatted. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the related harness/cable and connector. 2. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 3. Reinstall the system software using SST or a USB flash drive. 4. Check/replace the related parts. |
| Error code: | E602-0020-00 |
| Description: | HDD error |
| Causes: | Corruption of database managing user mode/service mode data was detected. |
| Remedy: | [Related parts] - HDD [Remedy] While this error occurs, backup of the setting values is disabled. In addition, it may not be recorded in the error log. Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power. 2. Enter safe mode using (2+8) startup, and format the HDD using a USB flash drive. 3. Replace the HDD. |
| Error code: | E602-0101-00 |
| Description: | HDD error |
| Causes: | An error was detected in the PDL-related file storage area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0111-00 |
| Description: | HDD error |
| Causes: | An error was detected in the PDL-related file storage area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "1", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0201-00 |
| Description: | HDD error |
| Causes: | An error was detected in the storage area of image data after startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0211-00 |
| Description: | HDD error |
| Causes: | An error was detected in the storage area of image data after startup. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "2", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0301-00 |
| Description: | HDD error |
| Causes: | An error was detected in the MEAP-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0311-00 |
| Description: | HDD error |
| Causes: | An error was detected in the MEAP-related area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "3", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0401-00 |
| Description: | HDD error |
| Causes: | Logical partition error was detected. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "4", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "4", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to the error, enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0411-00 |
| Description: | HDD error |
| Causes: | Logical partition error was detected. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "4", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "4", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to the error, enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0501-00 |
| Description: | HDD error |
| Causes: | An error was detected in the storage area of image data after startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0511-00 |
| Description: | HDD error |
| Causes: | An error was detected in the storage area of image data after startup. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "5", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0601-00 |
| Description: | HDD error |
| Causes: | An error was detected in the storage area of image data after startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "6", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "6", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0611-00 |
| Description: | HDD error |
| Causes: | An error was detected in the storage area of image data after startup. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "6", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "6", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0701-00 |
| Description: | HDD error |
| Causes: | An error was detected in general application temporary area (temporary file). (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "7", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "7", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0711-00 |
| Description: | HDD error |
| Causes: | An error was detected in general application temporary area (temporary file). (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "7", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "7", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0801-00 |
| Description: | HDD error |
| Causes: | An error was detected in the general application-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0811-00 |
| Description: | HDD error |
| Causes: | An error was detected in the general application-related area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0901-00 |
| Description: | HDD error |
| Causes: | An error was detected in PDL spool data (temporary file). (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "9", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "9", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-0911-00 |
| Description: | HDD error |
| Causes: | An error was detected in PDL spool data (temporary file). (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "9", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "9", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1001-00 |
| Description: | HDD error |
| Causes: | An error was detected in the SEND-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "10", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "10", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1011-00 |
| Description: | HDD error |
| Causes: | An error was detected in the SEND-related area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "10", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "10", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1101-00 |
| Description: | HDD error |
| Causes: | An error was detected in the update-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "11", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "11", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1111-00 |
| Description: | HDD error |
| Causes: | An error was detected in the update-related area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "11", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "11", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1201-00 |
| Description: | HDD error |
| Causes: | An error was detected in the license-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 5. 1. Check the related harness/cable and connector. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "12", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 4. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 5. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1211-00 |
| Description: | HDD error |
| Causes: | An error was detected in the license-related area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 5. 1. Check the related harness/cable and connector. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "12", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 4. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 5. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1301-00 |
| Description: | HDD error |
| Causes: | An error was detected in the system area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 5. 1. Check the related harness/cable and connector. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "13", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 4. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 5. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1311-00 |
| Description: | HDD error |
| Causes: | An error was detected in the system area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 5. 1. Check the related harness/cable and connector. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "13", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 4. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 5. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1401-00 |
| Description: | HDD error |
| Causes: | An error was detected in SWAP (temporary file/alternative memory area). (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "14", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "14", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1411-00 |
| Description: | HDD error |
| Causes: | An error was detected in SWAP (temporary file/alternative memory area). (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "14", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "14", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1701-00 |
| Description: | HDD error |
| Causes: | An error was detected in the debug log area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "17", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "17", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1711-00 |
| Description: | HDD error |
| Causes: | An error was detected in the debug log area. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "17", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "17", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1801-00 |
| Description: | HDD error |
| Causes: | An error was detected in the image data storage area in Advanced Box. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "18", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "18", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1811-00 |
| Description: | HDD error |
| Causes: | An error was detected in the image data storage area in Advanced Box. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "18", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "18", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1901-00 |
| Description: | HDD error |
| Causes: | An error was detected in the storage area of data for printing. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "19", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "19", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-1911-00 |
| Description: | HDD error |
| Causes: | An error was detected in the storage area of data for printing. (File could not be written in the HDD after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "19", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "19", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. If the above-mentioned service mode cannot be executed due to an error, etc., enter safe mode using (2+8) startup. Then format the HDD using SST or a USB flash drive. 6. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-2000-00 |
| Description: | HDD error |
| Causes: | I/O error was detected in the file system after startup. |
| Remedy: | [Related parts] - HDD [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the HDD optional board is properly installed. 2. Turn ON the main power, and check whether the error is cleared. 3. Execute the key clear using SST (to make an unformatted disk). [CAUTION] E602-0001 will be indicated if activating the machine with the unformatted disk. Therefore, be sure to format the HDD. 4. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. |
| Error code: | E602-2001-00 |
| Description: | HDD error |
| Causes: | Mismatch on encryption operation |
| Remedy: | [Related parts] - Main Controller PCB(UN6) - HDD [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Main Controller PCB is installed properly. 2. Turn ON the main power, and check whether the error is cleared. 3. Execute the key clear using SST (to make an unformatted disk). [CAUTION] E602-0001 will be indicated if activating the machine with the unformatted disk. Therefore, be sure to format the HDD. 4. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. |
| Error code: | E602-2002-00 |
| Description: | HDD error |
| Causes: | Failure of encryption board and others |
| Remedy: | [Related parts] - Main Controller PCB(UN6) - HDD [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn ON the main power, and check whether the error is cleared. 2. Execute the key clear using SST (to make an unformatted disk). [CAUTION] E602-0001 will be indicated if activating the machine with the unformatted disk. Therefore, be sure to format the HDD. 3. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 4. Replace the Main Controller PCB. |
| Error code: | E602-5001-00 |
| Description: | Encryption Chip error |
| Causes: | Error of the encryption chip on the Main Controller |
| Remedy: | [Related parts] Main Controller PCB(UN6) [Remedy] Replace the Main Controller PCB |
| Error code: | E602-5002-00 |
| Description: | HDD error |
| Causes: | A non-genuine HDD was detected. |
| Remedy: | [Related parts] - HDD [Remedy] 1. Replace the HDD with a genuine one. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. 2. Format the HDD using SST or a USB flash drive. |
| Error code: | E602-FF01-00 |
| Description: | HDD error |
| Causes: | An unidentified HDD error was detected at startup. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Main Controller PCB(UN6) - HDD [Reference] For backup and restoration, refer to "Appendix> Backup Data List" in the System Service Manual. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the related harness/cable and connector. 2. Format the HDD using SST or a USB flash drive. 3. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E602-FF11-00 |
| Description: | HDD error |
| Causes: | An unidentified HDD error was detected after startup. |
| Remedy: | [Related parts] R2.00 - Main Controller PCB(UN6) - HDD [Reference] For backup and restoration, refer to "Appendix> Backup Data List" in the System Service Manual. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the related harness/cable and connector. 2. Format the HDD using SST or a USB flash drive. 3. Check/replace the related parts. [Reference] When replacing the HDD, back up the setting values by referring to "Chapter 5. Adjustment> Actions when Replacing the Parts> HDD" in the Service Manual. |
| Error code: | E604-1024-00 ... E613-1536-00 |
| Description: | Faulty/insufficient image memory |
| Causes: | No necessary memory at Main Controller PCB |
| Remedy: | Replace the Main Controller PCB. |
| Error code: | E613-2048-00 |
| Description: | Memory error |
| Causes: | Memory of the Main Controller PCB is faulty. |
| Remedy: | [Related parts] - Main Controller PCB(UN6) [Remedy] Replace the Main Controller PCB. |
| Error code: | E614-0001-00 ... E614-0411-00 |
| Description: | Flash PCB error |
| Causes: | The Flash PCB could not be recognized, or the Flash PCB was not formatted. |
| Remedy: | [Related parts] R2.00 - Flash PCB - Main Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB again to check that it is installed properly. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 3. Replace the Main Controller PCB. |
| Error code: | E614-0501-00 |
| Description: | Error in file system on the Flash PCB |
| Causes: | An error was detected in the general application-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Flash PCB(UN91) - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. Enter safe mode using (2+8) startup, and reinstall the system software using SST or a USB flash drive. 6. Check/replace the related parts. |
| Error code: | E614-0511-00 |
| Description: | Error in file system on the Flash PCB |
| Causes: | An error was detected in the general application-related area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Flash PCB(UN91) - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. Enter safe mode using (2+8) startup, and reinstall the system software using SST or a USB flash drive. 6. Check/replace the related parts. |
| Error code: | E614-0601-00 |
| Description: | Error in system on the Flash PCB |
| Causes: | An error was detected in the license-related area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Flash PCB(UN91) - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 3. Replace the Main Controller PCB. |
| Error code: | E614-0611-00 |
| Description: | Error in system on the Flash PCB |
| Causes: | An error was detected in the license-related area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Flash PCB(UN91) - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 3. Replace the Main Controller PCB. |
| Error code: | E614-0701-00 |
| Description: | Error in file system on the Flash PCB |
| Causes: | An error was detected in system setting value (service mode, etc.) storage area. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Flash PCB(UN91) - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. Check/replace the related parts. |
| Error code: | E614-0711-00 |
| Description: | Error in file system on the Flash PCB |
| Causes: | An error was detected in system setting value (service mode, etc.) storage area. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Flash PCB(UN91) - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. When prioritizing clearing of the error, skip Remedies 2 and 3. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 4. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "8", and execute "HD-CLEAR". Then, turn OFF and then ON the main power to delete the data in the corresponding partition. 5. Check/replace the related parts. |
| Error code: | E614-4000-00 ... E614-4003-00 |
| Description: | Error in system on the Flash PCB |
| Causes: | The OS could not be recognized. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB again to check that it is installed properly. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 3. Check that the HDD and the cables are properly installed. 4. Enter safe mode using (2+8) startup, and format the HDD using SST or a USB flash drive. 5. If another error occurs, clear the error by performing the remedy for it. 6. Replace the Main Controller PCB. |
| Error code: | E614-4010-00 ... E614-9000-00 |
| Description: | Error in system on the Flash PCB |
| Causes: | The OS in safe mode could not be recognized. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB again to check that it is installed properly. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. |
| Error code: | E614-9001-00 ... E614-9004-00 |
| Description: | Error in system on the Flash PCB |
| Causes: | Error in memory allocation/invalid memory (at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. After turning OFF the main power, remove and then install the Flash PCB again to check that it is installed properly. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. |
| Error code: | E614-FF01-00 |
| Description: | Error in system on the Flash PCB |
| Causes: | An unidentified Flash error was detected at startup. (Initialization failed at startup or I/O error at startup) When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log. |
| Remedy: | [Related parts] R2.00 - Flash PCB(UN91) - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 5. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 5. Replace the Main Controller PCB. |
| Error code: | E614-FF11-00 |
| Description: | Error in system on the Flash PCB |
| Causes: | An unidentified Flash error was detected at startup. (File could not be written in the Flash PCB after startup or I/O error after startup) |
| Remedy: | [Related parts] R2.00 - Flash PCB(UN91) - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. Although the error is cleared by "HD-CHECK", it may occur again. Thus, perform Remedies 1 to 5. 1. Check the related harness/cable and connector. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> "0", and execute "HD-CHECK". Then, turn OFF and then ON the main power. 3. Obtain the necessary backup data by referring to "Appendix> Backup Data List" in the System Service Manual. 4. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 5. Replace the Main Controller PCB. |
| Error code: | E615-0001-00 |
| Description: | Error in self-diagnosis of the encryption module |
| Causes: | An error was detected in self-diagnosis of the encryption library. |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software and restore the backup data once the error is cleared. 1. After reinstalling the system software using SST or a USB flash drive, turn OFF and then ON the main power. 2. Obtain the necessary backup data by referring to the backup data list. 3. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB flash drive. 4. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E674-0001-07 ... E674-0008-07 |
| Description: | Fax Board communication error |
| Causes: | An error was detected for the specified number of times in communication with the Fax Board. |
| Remedy: | [Related parts] R1.00 - Harness between the Fax Board and the Main Controller PCB - Fax Board - Main Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E674-0010-07, E674-0011-07 |
| Description: | Fax Board communication error |
| Causes: | A communication error occurred when opening the Timer Device used for fax. |
| Remedy: | Check/replace the Main Controller PCB |
| Error code: | E674-0020-07 |
| Description: | Fax Board communication error |
| Causes: | An error occurred in the modem IC used for fax. |
| Remedy: | [Related parts] R1.00 - Harness between the Fax Board and the Main Controller PCB - Fax Board - Main Controller PCB(UN6) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E674-0021-07 |
| Description: | Fax Board communication error |
| Causes: | A Fax Board for non-supported modem has been connected. |
| Remedy: | Replace it with a genuine Fax Board (for 1-line or 2-line). |
| Error code: | E674-0030-07 |
| Description: | Fax Board communication error |
| Causes: | Check sum error |
| Remedy: | System software download for 2 line FAX |
| Error code: | E674-0100-07 |
| Description: | Fax Board communication error |
| Causes: | After completion of fax communication, writing of the communication information (log) failed, and the log could not be read. |
| Remedy: | Turn OFF and then ON the main power. If it occurs when the power is turned OFF and then ON after executing FAX > Clear > ALL, execute FAX > Clear > ALL and turn OFF and then ON the power again. [CAUTION] The previous communication information (log) will be cleared by turning OFF and then ON the main power. |
| Error code: | E674-0300-07 |
| Description: | Fax configuration error |
| Causes: | It was detected that there was a Fax Board for multiple lines installed while the IP Fax license was enabled. |
| Remedy: | - Remove the Fax Board for multiple lines to use the machine as an IP Fax model. - Uninstall the IP Fax license to use the machine as a G3 Fax model. |
| Error code: | E674-0301-07 |
| Description: | Fax configuration error |
| Causes: | It was detected that there was no 1-line Fax Board installed while the IP Fax license was enabled. |
| Remedy: | - Install the Fax Board (1-line) to use the machine as an IP Fax model. - Uninstall the IP Fax license and install the G3 Fax Board to use the machine as a G3 Fax model. |
| Error code: | E713-0000-05 |
| Description: | Communication error |
| Causes: | The operation was not completed although retry of the communication between the host machine (Dcon) and the Finisher was performed for 3 consecutive times. |
| Remedy: | [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the connector of the Interface Harness is not disconnected. 2. Replace the Finisher Controller PCB. 3. Replace the Interface Harness. |
| Error code: | E719-0001-00 |
| Description: | Error in Coin Vendor. |
| Causes: | Error in starting of the CoinVendor - The Coin Vendor, which should have been connected before the power was turned OFF, is not connected when the power is turned ON. |
| Remedy: | Check the connection between charging management equipment and machine, and check that the Cable is not open-circuit. Clear the error while the charging management equipment is connected to operate and when switching to the operation without charging management equipment. (To prevent the misuse by removing the charging management equipment, this error code is displayed.) |
| Error code: | E719-0002-00 |
| Description: | Error in Coin Vendor. |
| Causes: | Error in IPC when CoinVendor is running. - In the case of disconnection of IPC or an error in which IPC communication failed to be recovered. - When disconnection of the pickup delivery signal is detected. - When illegal connection is detected (short-circuit with Tx and Rx of IPC) |
| Remedy: | Check the connection between charging management equipment and machine, and check that the Cable is not open-circuit. Clear the error while the charging management equipment is connected to operate and when switching to the operation without charging management equipment. (To prevent the misuse by removing the charging management equipment, this error code is displayed.) |
| Error code: | E719-0003-00 |
| Description: | Error in Coin Vendor. |
| Causes: | - In the case of communication error with the coin vendor while obtaining the unit price at start-up. |
| Remedy: | Check the connection between charging management equipment and machine, and check that the Cable is not open-circuit. Clear the error while the charging management equipment is connected to operate and when switching to the operation without charging management equipment. (To prevent the misuse by removing the charging management equipment, this error code is displayed.) |
| Error code: | E719-0004-00 |
| Description: | Coin vendor error |
| Causes: | The coin vendor was connected to a model that does not support the coin vendor |
| Remedy: | Cancel the connection of the coin vendor and clear the error. |
| Error code: | E719-0031-00 |
| Description: | Error in serial communication at the start of the New Card Reader |
| Causes: | Failure in communication with the serial New Card Reader at start-up. |
| Remedy: | - Check if the cable of the serial New Card Reader is disconnected. - Take out the serial New Card Reader. - COPIER > Function > CLEAR > CARD - COPIER > Function > CLEAR > ERR |
| Error code: | E719-0032-00 |
| Description: | Error in serial communication at the start of the New Card Reader |
| Causes: | Communication failed in the middle of the operation although communication with the serial New Card Reader was successful at start-up. |
| Remedy: | - Check if the cable of the serial New Card Reader is disconnected. |
| Error code: | E719-0041-00 |
| Description: | Coin vendor error |
| Causes: | Communication with the coin vendor could not be established at startup of the host machine. (Charge mode (COIN = 6) has been set.) |
| Remedy: | 1. If it operates in charge mode (COIN = 6) - Check that it is the supported charging management equipment. - Check the cable to be connected. - Check the power of the charging management equipment. 2. If charge mode is canceled - Select COPIER> OPTION> ACC> COIN> "0", and turn OFF and then ON the main power. |
| Error code: | E719-0042-00 |
| Description: | Coin vendor error |
| Causes: | Communication with the coin vendor could not be established at startup of the host machine. (Charge mode (COIN = 6) has been set.) |
| Remedy: | 1. If it operates in charge mode (COIN = 6) - Check that it is the supported charging management equipment. - Check the cable to be connected. - Check the power of the charging management equipment. 2. If charge mode is canceled - Select COPIER> OPTION> ACC> COIN> "0", and turn OFF and then ON the main power. |
| Error code: | E720-0001-00 |
| Description: | Error due to non-compatible Finisher |
| Causes: | Non-compatible Finisher was connected. |
| Remedy: | Connect either the Staple Finisher-Z1. |
| Error code: | E720-0001-05 |
| Description: | Error due to non-compatible Finisher |
| Causes: | Non-compatible Finisher was connected. |
| Remedy: | Connect either the Staple Finisher-Z1. |
| Error code: | E730-C001-00 |
| Description: | Error in HDD access |
| Causes: | An error occurred when accessing the HDD. |
| Remedy: | [Related parts] R1.00 - Harness between the Main Controller PCB and the HDD - HDD - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Format the HDD and reinstall the system software using SST or a USB flash drive. 2. Check/replace the related harness/cable, connector and parts. |
| Error code: | E732-0001-04 |
| Description: | Communication error |
| Causes: | DDI-S communication error. |
| Remedy: | [Related parts] R1.00 - Harness between ADF UNIT (J5) and the Main Controller PCB (UN6/J4002) - Harness between READER UNIT (J6) and the Main Controller PCB (UN6/J4001) - READER ADF UNIT - Main Controller PCB (UN6) - DC Controller PCB (UN1) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E732-0010-00 |
| Description: | Communication error |
| Causes: | A signal to start image transfer could not be detected at scanning although the specified period of time (120 sec) has passed. |
| Remedy: | [Related parts] R1.00 - Harness between the READER ADF UNIT (J6, J5) and the Main Controller PCB (UN6/J4001, 4002) - READER ADF UNIT - Main Controller PCB (UN6) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E732-0020-00 |
| Description: | Communication error |
| Causes: | A communication error between the Reader Controller PCB and the Main Controller PCB was detected. |
| Remedy: | [Related parts] R1.00 - Harness between the READER ADF UNIT (J6, J5) and the Main Controller PCB (UN6/J4001, 4002) - READER ADF UNIT - Main Controller PCB (UN6) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E732-0021-00 |
| Description: | Communication error |
| Causes: | A communication error between the Reader Controller PCB and the Main Controller PCB was detected. |
| Remedy: | [Related parts] R1.00 - Harness between the READER ADF UNIT (J6, J5) and the Main Controller PCB (UN6/J4001, 4002) - READER ADF UNIT - Main Controller PCB (UN6) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E732-0022-00 |
| Description: | Communication error |
| Causes: | A communication error between the Reader Controller PCB and the Main Controller PCB was detected. |
| Remedy: | [Related parts] R1.00 - Harness between the READER ADF UNIT (J6, J5) and the Main Controller PCB (UN6/J4001, 4002) - READER ADF UNIT - Main Controller PCB (UN6) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E732-0023-04 |
| Description: | Communication error |
| Causes: | DDI-S communication error (SPRDY-S detection error) |
| Remedy: | [Related parts] R1.00 - Harness between the READER ADF UNIT (J6, J5) and the Main Controller PCB (UN6/J4001, 4002) - READER ADF UNIT - Main Controller PCB (UN6) [Remedy] Check/replace the related parts. After performing the remedy, check that the copy image is output normally. |
| Error code: | E732-0F01-04 |
| Description: | Communication error |
| Causes: | Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0001 is generated. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E732-0F20-00 |
| Description: | Communication error |
| Causes: | Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0020 is generated. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E732-0F21-00 |
| Description: | Communication error |
| Causes: | Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0021 is generated. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E732-0F22-00 |
| Description: | Communication error |
| Causes: | Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0022 is generated. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E732-0F23-04 |
| Description: | Communication error |
| Causes: | Communication error that can be recovered by reboot If it is detected again immediately after reboot, E732-0023 is generated. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E733-0000-05 |
| Description: | Printer communication error |
| Causes: | A communication error between the DC Controller PCB and the Main Controller PCB was detected at startup. |
| Remedy: | [Related parts] R1.00 - Harnesses between the DC Controller PCB (UN1/J112) and the Main Controller PCB (UN6/ J4511) - DC Controller PCB (UN1) - Main Controller PCB (UN6) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E733-0001-05 |
| Description: | Printer communication error |
| Causes: | A communication error between the DC Controller PCB and the Main Controller PCB was detected. |
| Remedy: | [Related parts] R1.00 - Harnesses between the DC Controller PCB (UN1/J112) and the Main Controller PCB (UN6/ J4511) - DC Controller PCB (UN1) - Main Controller PCB (UN6) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E733-0002-05 |
| Description: | Printer communication error |
| Causes: | Signal error was detected after establishment of communication between the DC Controller PCB and the Main Controller PCB. |
| Remedy: | [Related parts] R1.00 - Harnesses between the DC Controller PCB (UN1/J112) and the Main Controller PCB (UN6/ J4511) - DC Controller PCB (UN1) - Main Controller PCB (UN6) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E733-0F00-05 ... E733-0F02-05 |
| Description: | Printer communication error |
| Causes: | Communication error that can be recovered by reboot If it is detected again immediately after reboot, E733-0000 is generated. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E733-F000-05, E733-F001-05 |
| Description: | Printer communication error |
| Causes: | Disconnection of a cable between the Main Controller PCB and the DC Controller PCB was detected. |
| Remedy: | [Remedy] Check/replace the harness between the DC Controller PCB and the Main Controller PCB. |
| Error code: | E733-F002-05 |
| Description: | Printer communication error |
| Causes: | A communication error between the Main Controller PCB and the Laser Driver PCB was detected. |
| Remedy: | [Related parts] 2.00 - Flat Cable between the DC Controller PCB (UN1/J110) and the Laser Driver PCB (J410) - Flat Cable between the Main Controller PCB (UN6/J9000) and the DC Controller PCB (UN1/ J104) - Laser Scanner Assembly - Main Controller PCB (UN6) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E743-0000-04 |
| Description: | DDI communication error |
| Causes: | Software sequence error |
| Remedy: | Collect debug log and contact to the sales company. |
| Error code: | E744-0001-00 |
| Description: | Language file error |
| Causes: | The language file in HDD was not supported by the version of Bootable. |
| Remedy: | Reinstall the correct language file using SST or USB flash drive reinstall the entire software. |
| Error code: | E744-0003-00 |
| Description: | Language file error |
| Causes: | The language file to be switched to that was described in the Config.txt in HDD was not found. |
| Remedy: | Reinstall the correct language file using SST or USB flash drive reinstall the entire software. |
| Error code: | E744-0004-00 |
| Description: | Language file error |
| Causes: | Switching to the language file in the HDD failed. |
| Remedy: | Reinstall the correct language file using SST or USB flash drive reinstall the entire software. |
| Error code: | E744-2000-00 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E744-5000-07 |
| Description: | Mismatch of software version for fax |
| Causes: | After the Fax Board (option) has been installed, mismatch of version of software in the Fax Board was detected at transmission and reception. |
| Remedy: | Upgrade the system software version to the latest one. |
| Error code: | E746-0011-00 |
| Description: | Voice Board error |
| Causes: | Both the Voice Guidance PCB and the Voice Operation PCB are inserted. |
| Remedy: | Insert only 1 board of the appropriate voice board. |
| Error code: | E746-0021-00 |
| Description: | Image Analysis Board error |
| Causes: | Self-check NG of Image Analysis Board |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Remove and then install the Image Analysis Board. 2. If the error is not cleared, replace the Image Analysis Board. 3. After replacing the Image Analysis Board, reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB flash drive. |
| Error code: | E746-0022-00 |
| Description: | Image Analysis Board error |
| Causes: | Different version of Image Analysis Board (PCB used for PCAM) |
| Remedy: | Reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB flash drive. |
| Error code: | E746-0023-00 |
| Description: | Image Analysis Board error |
| Causes: | No response from Image Analysis Board (PCB used for PCAM) |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Remove and then install the Image Analysis Board. 2. If the error is not cleared, replace the Image Analysis Board. 3. After replacing the Image Analysis Board, reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB flash drive. |
| Error code: | E746-0024-00 |
| Description: | Image Analysis Board error |
| Causes: | Failure in behavior of Image Analysis Board (PCB used for PCAM) |
| Remedy: | Perform the following in the order while checking whether the error is cleared. 1. Remove and then install the Image Analysis Board. 2. If the error is not cleared, replace the Image Analysis Board. 3. After replacing the Image Analysis Board, reinstall the firmware of the Image Analysis Board or the system software which version is supported by this model using SST or a USB flash drive. |
| Error code: | E746-0031-00 |
| Description: | TPM error |
| Causes: | A communication error has occurred between the Main Controller PCB and the TPM PCB at startup. |
| Remedy: | [Related parts] - TPM PCB [Remedy] Check/replace the TPM PCB. [Reference] After replacing the TPM PCB, if the TPM key was backed up, restore the key. 1. Connect the USB memory which stores the TPM key. 2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3. Enter the password set at backup operation. 4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power. |
| Error code: | E746-0032-00 |
| Description: | TPM error |
| Causes: | Mismatch of the TPM key was detected. |
| Remedy: | [Related parts] - TPM PCB [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Format the HDD and reinstall the system software using SST or a USB flash drive. 2. Replace the TPM PCB. [Reference] After replacing the TPM PCB, if the TPM key was backed up, restore the key. 1. Connect the USB memory which stores the TPM key. 2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3. Enter the password set at backup operation. 4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power. |
| Error code: | E746-0033-00 |
| Description: | TPM error |
| Causes: | It was detected that data in TPM was inconsistent. |
| Remedy: | [Related parts] - TPM PCB [Remedy] If the TPM key was backed up, - Restore the TPM key. 1. Connect the USB memory which stores the TPM key. 2. Execute "Settings/Registration> Log In> Management Settings> Data Management> TPM Settings> Restore TPM Key". [CAUTION] Ask the customer to enter "System Manager ID" and "System Manager PIN" when logging in. 3. Enter the password set at backup operation. 4. When the restoration completion screen is displayed, click "OK". Remove the USB memory, and turn OFF and then ON the main power. If the TPM key was not backed up, - Format the HDD and reinstall the system software using SST or a USB flash drive. |
| Error code: | E746-0034-00 |
| Description: | TPM auto recovery error |
| Causes: | The error occurred when clearing HDD while TPM setting was ON. |
| Remedy: | [Related parts] - HDD [Remedy] It is recovered by turning OFF and then ON the power. If the error is not cleared, format the HDD and reinstall the system software using SST or a USB flash drive. |
| Error code: | E746-0035-00 |
| Description: | TPM version error |
| Causes: | TPM PCB which cannot be used in this machine was installed. |
| Remedy: | [Related parts] - TPM PCB [Remedy] Install the TPM PCB for this model. |
| Error code: | E748-2000-00, E748-2001-00 |
| Description: | Main Controller PCB access error |
| Causes: | Main Controller PCB Chip access error. |
| Remedy: | Check/replace the Main Controller PCB (UN81) |
| Error code: | E748-2010-00 |
| Description: | Flash PCB error / HDD error |
| Causes: | IPL (startup program) was not found, or the HDD could not be recognized. |
| Remedy: | [Related parts] R1.00 - Harness between the Main Controller PCB (UN6/J6003, J6004) and the HDD - HDD - Flash PCB (UN91)(UN91) - Main Controller PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. - Disconnect the cable between the Main Controller PCB and the HDD, and turn ON the main power. a. When the error code has not been changed: 1. Obtain the necessary backup data by referring to the backup data list. 2. Enter safe mode using (2+8) startup, and execute [4] Clear/Format> [2] Flash Format (Flash format) using a USB flash drive.. 3. After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. 4. Restore the backup data. b. When the error code has been changed to another one, see the remedy for the corresponding code. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual. |
| Error code: | E748-2011-00 |
| Description: | Flash PCB error |
| Causes: | OS was not found at startup. |
| Remedy: | [Related parts] - Flash PCB (UN91) [Remedy] After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. |
| Error code: | E748-2012-00 |
| Description: | Flash PCB error |
| Causes: | Cannot mount the OS in safe mode startup or No OS startup script |
| Remedy: | [Related parts] - Flash PCB (UN91) [Remedy] After replacing the Flash PCB, reinstall the system software using SST or a USB flash drive. |
| Error code: | E748-2021-00 ... E748-4910-00 |
| Description: | Main Controller PCB access error |
| Causes: | Main controller board access errors |
| Remedy: | Check/replace the Main Controller PCB (UN81) |
| Error code: | E748-9000-00 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales company. |
| Error code: | E749-0008-00 |
| Description: | Error due to the DC Controller not compatible with the model |
| Causes: | The DC Controller PCB or the Main Controller PCB which was used with another model was detected. |
| Remedy: | It is not necessary to perform a remedy because the machine is automatically rebooted after log collection. |
| Error code: | E753-0001-00 |
| Description: | Download Error |
| Causes: | Update of the system software failed. |
| Remedy: | [Related parts] - Flash PCB (UN91) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power. 2. Reinstall the system software using SST or a USB memory. 3. Replace the FLASH PCB, and reinstall the system software. 4. Collect debug log and contact the sales company. |
| Error code: | E760-0001-00 |
| Description: | Main Controller PCB internal error |
| Causes: | An error was detected in the Main Controller PCB. |
| Remedy: | [Related parts] - Main Controller PCB(UN6) [Remedy] Check/replace the Main Controller PCB (UN6) |
| Error code: | E804-0000-00 |
| Description: | Power Supply Cooling Fan error |
| Causes: | It was detected that the Power Supply Cooling Fan was locked. |
| Remedy: | [Related parts] R1.00 - Harness between the Low-voltage Power Supply PCB (UN01/J323) and the Power Supply Cooling Fan (FM05/J5215) - Power Supply Cooling Fan (FM05) - Low-voltage Power Supply PCB (UN01) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E806-0100-05 |
| Description: | Drum Unit Suction Cooling Fan error |
| Causes: | The Drum Unit Suction Cooling Fan did not rotate for the specified period of time since the start of drive. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J180) and the Primary Transfer High-voltage PCB (UN03/J271) - Harness between the Primary Transfer High-voltage PCB (UN03/J272) and the Drum Unit Suction Cooling Fan (FM01) - Drum Unit Suction Cooling Fan (FM01) - Primary Transfer High-voltage PCB (UN03) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E806-0101-05 |
| Description: | Drum Unit Suction Cooling Fan error |
| Causes: | The Drum Unit Suction Cooling Fan rotated for more than the specified period of time after the stop of drive. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J180) and the Primary Transfer High-voltage PCB (UN03/J271) - Harness between the Primary Transfer High-voltage PCB (UN03/J272) and the Drum Unit Suction Cooling Fan (FM01) - Drum Unit Suction Cooling Fan (FM01) - Primary Transfer High-voltage PCB (UN03) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E806-0300-05 |
| Description: | Delivery Cooling Fan error |
| Causes: | The Delivery Cooling Fan did not rotate for the specified period of time since the start of drive. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J151) and the Delivery Cooling Fan (FM03/ J5413) - Delivery Cooling Fan (FM03) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E806-0301-05 |
| Description: | Delivery Cooling Fan error |
| Causes: | The Delivery Cooling Fan rotated for more than the specified period of time after the stop of drive. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J151) and the Delivery Cooling Fan (FM03/ J5413) - Delivery Cooling Fan (FM03) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E806-0400-05 |
| Description: | Duplex Cooling Fan error |
| Causes: | The Duplex Cooling Fan in the Right Cover did not rotate for the specified period of time since the start of drive. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J122) and the Duplex Cooling Fan (FM04/J5610) - Duplex Cooling Fan (FM04) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E806-0401-05 |
| Description: | Duplex Cooling Fan error |
| Causes: | The Duplex Cooling Fan in the Right Cover rotated for more than the specified period of time after the stop of drive. |
| Remedy: | [Related parts] R1.00 - Harness between the DC Controller PCB (UN04/J122) and the Duplex Cooling Fan (FM04/J5610) - Duplex Cooling Fan (FM04) - DC Controller PCB (UN04) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES |
| Error code: | E808-0001-05 |
| Description: | Low-voltage Power Supply PCB error |
| Causes: | Error is reported under any of the following conditions. (1) The power supply input voltage detected by CAREN IC at the startup of the DC Controller PCB was less than the specified value (75 V for the 100 V system, 165 V for the 200 V system). (2) The following symptom consecutively occurred twice: Only less than 20.8 V voltage was output from the 24 V power supply after 3 seconds from the start of the 24 V power supply operation at the startup of the DC Controller PCB. (3) CAREN IC detected power supply input voltage less than the specified value (70 V for the 100 V system, 160 V for the 200 V system) for 1.5 consecutive seconds while the 24 V power supply was ON after CAREN IC detected power supply input voltage equal to or higher than the specified value (75 V for the 100 V system, 165 V for the 200 V system). (4) While the 24 V power supply was ON, after an output equal to or higher than 20.8 V was detected, an output less than 18.5 V was detected from the 24 V power supply for 1 consecutive second. |
| Remedy: | [Related parts] - Harness between the Connector J208 on the Low-voltage Power Supply PCB and the Connector J102 on the DC Controller PCB - Low-voltage Power Supply PCB - DC Controller PCB(UN1) [Remedy] - Disconnect and then connect again the Connectors J207 and J208 on the Low-voltage Power Supply PCB and the Connectors J102 and J103 on the DC Controller PCB. - Replace the Low-voltage Power Supply PCB. |
| Error code: | E880-0001-00 |
| Description: | Controller Cooling Fan error |
| Causes: | It was detected that the Controller Cooling Fan was locked. |
| Remedy: | [Related parts] R1.00 - Controller Cooling Fan - Main Controller PCB (UN6) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E880-0003-00 |
| Description: | Controller Cooling Fan error |
| Causes: | It was detected that the Controller Cooling Fan was locked. |
| Remedy: | [Related parts] R1.00 - Controller Cooling Fan - Main Controller PCB (UN6) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E880-0005-00 |
| Description: | Controller Cooling Fan error |
| Causes: | Fan lock of the HDD Cooling Fan was detected |
| Remedy: | Check if the connector is connected. It the connection is OK, replace the HDD Cooling Fan. |
| Error code: | E881-0001-00 |
| Description: | Board over heat error |
| Causes: | Abnormal temperature of the Main Controller CPU was detected. |
| Remedy: | [Related parts] - Main Controller PCB(UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. a. If the error occurred during a service visit and then occurred again, replace the Main Controller PCB. b. If the error does not occur during a service visit but is found in the log: 1. Clean the inlet on the side where the fan is installed and remove dust. 2. Remove dust from the Controller Cooling Fan. 3. If the space on the side where the fan is installed is less than 10 cm, ask the customer to secure enough space. |
| Error code: | E882-0001-05 |
| Description: | Main Power Supply Switch error |
| Causes: | The main power was not turned OFF due to the solenoid in the Main Power Switch not working. |
| Remedy: | [Related parts] R1.00 - Harness between the Main Controller PCB (UN81/J4513) and the Main Power Switch (SW01/ J5204, J5205) - Main Power Switch (SW01) - Main Controller PCB (UN81) [Remedy] Check/replace the related harness/cable, connector and parts. |
| Error code: | E996-0071-04 |
| Description: | Error for collecting sequence jam log (ADF) |
| Causes: | Error for collecting jam log (ADF) |
| Remedy: | [Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-R" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996-0CA1-05 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | [Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996-0CA2-05 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | Remedy] Collect debug log and contact the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996-0CA3-05 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | [Remedy] Collect debug log and contact the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996-0CA4-05 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | [Remedy] Collect debug log and contact the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996-0CA9-05 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | [Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996-0CAD-05 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | [Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996-0CAE-05 |
| Description: | Error for collecting sequence jam log (Printer) |
| Causes: | Error for collecting jam log (Printer) |
| Remedy: | [Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
| Error code: | E996-0CAF-05 |
| Description: | Error for collecting sequence jam log (Finisher) |
| Causes: | Error for collecting jam log (Finisher) |
| Remedy: | [Remedy] Collect debug log and contact to the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> JM-ERR-D" to "1", it is handled as an error instead of a jam from the first occurrence. |
