Canon imageRUNNER LBP3580
Рейтинг
Модули
101 INTERNAL COMPONENTS 1
100 EXTERNAL COVERS, PANEL, ETC.
105 INTERNAL COMPONENTS 5
102 INTERNAL COMPONENTS 2
103 INTERNAL COMPONENTS 3
931 MAIN CONTROLLER PCB ASSY (LBP3580)
930 MAIN CONTROLLER PCB ASSY (LBP3560)
104 INTERNAL COMPONENTS 4
106 INTERNAL COMPONENTS 6
Детали 101 INTERNAL COMPONENTS 1
| Деталь: | TAG HOLDER ASSY |
| Парткод: | RM1-6284-000 |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | RM1-6322-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | STOPPER, BUSHING ARM |
| Парткод: | RC2-7928-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-4218-000 |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, RIGHT FRONT |
| Парткод: | FC9-5319-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | LABEL, DUPLEXING JAM CLEARING |
| Парткод: | FC9-5364-000 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | EMBLEM |
| Парткод: | FC7-0509-000 |
| Деталь: | COVER, TOP UPPER LEFT |
| Парткод: | FC9-5308-000 |
| Деталь: | COVER, TOP UPPER LEFT |
| Парткод: | FE2-2856-000 |
| Деталь: | COVER, RIGHT REAR |
| Парткод: | FC9-5311-000 |
| Деталь: | COVER, RIGHT |
| Парткод: | FC9-5318-000 |
| Деталь: | COVER, DIMM |
| Парткод: | FC9-5353-000 |
| Деталь: | COVER, TOP UPPER RIGHT |
| Парткод: | FC9-5356-000 |
| Деталь: | COVER, TOP UPPER RIGHT |
| Парткод: | FM0-4731-000 |
| Деталь: | LABEL, JAM OPERATOR, REAR |
| Парткод: | FC9-5365-000 |
| Деталь: | LABEL, MULTI-PURPOSE SIZE |
| Парткод: | FC9-5377-000 |
| Деталь: | LABEL, TRAY EXTENSION MARK |
| Парткод: | FC9-5367-000 |
| Деталь: | LABEL, PRINT INSTRUCTION |
| Парткод: | FC9-5368-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | LABEL, HIGH TMP. CAUTION |
| Парткод: | FC9-5370-000 |
| Деталь: | REAR COVER ASSY |
| Парткод: | FM4-2203-000 |
| Деталь: | LEFT, COVER UNIT |
| Парткод: | FM4-2205-000 |
| Деталь: | RIGHT, UNDER COVER UNIT |
| Парткод: | FM4-2208-000 |
| Деталь: | COVER ASSY, RIGHT LOWER |
| Парткод: | FM0-3835-000 |
| Деталь: | CRG DOOR UNIT |
| Парткод: | FM4-2210-000 |
| Деталь: | CARTRIDGE DOOR ASSY |
| Парткод: | FM0-4805-000 |
| Деталь: | M.P. TRAY COVER ASSY |
| Парткод: | FM4-2243-000 |
| Деталь: | M.P. TRAY COVER ASSY |
| Парткод: | FM4-2252-000 |
| Деталь: | TOP, COVER, UNIT |
| Парткод: | FM4-2215-000 |
| Деталь: | TOP COVER ASSY, RIGHT |
| Парткод: | FM0-4732-000 |
| Деталь: | POWER SUPPLY SW PCB ASSY |
| Парткод: | FM4-5036-000 |
| Деталь: | POWER SUPPLY SWITCH PCB ASSY |
| Парткод: | FM0-4629-000 |
| Деталь: | OPERATION PANEL ASSY |
| Парткод: | FM4-6211-000 |
| Деталь: | OPERATION PANEL ASSY |
| Парткод: | FM0-4735-000 |
| Деталь: | M.P. TRAY LIFTING PLATE ASSY |
| Парткод: | FM4-2251-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | HINGE, MULTI-PURPOSE, LEFT |
| Парткод: | RC2-7705-000 |
| Деталь: | HINGE, MULTI-PURPOSE, RIGHT |
| Парткод: | RC2-7706-000 |
| Деталь: | CABLE, SWITCH |
| Парткод: | FM0-4628-000 |
| Деталь: | CABLE, USB |
| Парткод: | FM0-4643-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | FAN |
| Парткод: | RK2-1497-000 |
| Деталь: | CASSETTE PAPER PICK-UP ASSY |
| Парткод: | FM4-2222-000 |
| Деталь: | IDLER ROLLER ASSY |
| Парткод: | RM1-6271-000 |
| Деталь: | MULTI-PURPOSE SENSOR PCB ASSY |
| Парткод: | FM4-5037-000 |
| Деталь: | MULTI-PURPOSE SENSOR PCB ASSY |
| Парткод: | FM0-4632-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | RM1-6274-000 |
| Деталь: | ENGINE CONTROLLER ASSY |
| Парткод: | FM4-5677-000 |
| Деталь: | ENGINE CONTROLLER PCB ASSY |
| Парткод: | FM1-D917-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | MICROSWITCH |
| Парткод: | WC4-5171-000 |
| Деталь: | ENVIRONMENT SENSOR ASSY |
| Парткод: | FM4-5676-000 |
| Деталь: | TEMPERATURE SENSOR PCB ASSY |
| Парткод: | FM0-4635-000 |
| Деталь: | CST. PICK-UP ROLLER ASSY |
| Парткод: | RM1-6313-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-0155-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | RAIL ISLOT |
| Парткод: | FC9-5336-000 |
| Деталь: | DIMM ASSY |
| Парткод: | FM2-9829-000 |
| Деталь: | ROM PCB ASSEMBLY |
| Парткод: | FM4-6843-000 |
| Деталь: | COVER, SD |
| Парткод: | FE2-2844-000 |
| Деталь: | A.N. POWER SUPPLY PCB ASSEMBLY |
| Парткод: | FL3-8776-000 |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | AC CONNECTING PCB ASSEMBLY |
| Парткод: | FM0-4623-000 |
| Деталь: | CABLE, SUB POWER SUPPLY REMOTE |
| Парткод: | FM0-4627-000 |
| Деталь: | INTERNAL COMPONENTS 5 |
| Парткод: | NPN |
| Деталь: | SOLENOID |
| Парткод: | RK2-1490-000 |
| Деталь: | SOLENOID |
| Парткод: | RK2-1492-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | GEAR, 30T |
| Парткод: | RU6-0953-000 |
| Деталь: | GEAR, 17T |
| Парткод: | RU6-0948-000 |
| Деталь: | GEAR, 25T |
| Парткод: | RU6-0951-000 |
| Деталь: | GEAR, 26T |
| Парткод: | RU6-0952-000 |
| Деталь: | GEAR, 18T/19T |
| Парткод: | RU6-0956-000 |
| Деталь: | RATCHET GEAR ASSY |
| Парткод: | RM1-6282-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | REGISTRATION ROLLER ASSY |
| Парткод: | RM1-6272-000 |
| Деталь: | ROLLER, MULTI-PURPOSE |
| Парткод: | RL1-2412-000 |
| Деталь: | TRANSFER LOWER GUIDE ASSY |
| Парткод: | RM1-6315-000 |
| Деталь: | CSSETTE ASSY |
| Парткод: | FM4-2216-000 |
| Деталь: | BASE PLATE ROLLER ASSY |
| Парткод: | RM1-6306-000 |
| Деталь: | ROLLER, TRANSFER |
| Парткод: | RM1-6321-000 |
| Деталь: | PAD, MULTI-PURPOSE SEPARATION |
| Парткод: | RC2-8575-000 |
| Деталь: | SEPARATION HOLDER ASSY |
| Парткод: | RM1-6303-000 |
| Деталь: | LABEL, CST. PAPER SET |
| Парткод: | FC9-5363-000 |
| Деталь: | M.P. PAPER PICK-UP SHAFT ASSY |
| Парткод: | RM1-6314-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | IC, ASIC, MB8AA4241EPBH-GE1 |
| Парткод: | FK3-1800-000 |
| Деталь: | IC, K9F4G08U0D-SCB0 FLASH |
| Парткод: | FL3-9355-000 |
| Деталь: | IC, K9F4G08U0D-SCB0 FLASH |
| Парткод: | FL3-9345-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY |
| Парткод: | FM0-4639-000 |
| Деталь: | IC, 24LC256-I/PG, EEP-ROM |
| Парткод: | WA7-4673-000 |
| Деталь: | IC,S1 L50552F 32L000, ASIC |
| Парткод: | FH4-6302-000 |
| Деталь: | MAIN CONTROLLER PCB ASSY |
| Парткод: | FM4-6145-000 |
| Деталь: | FAN |
| Парткод: | RK2-1499-000 |
| Деталь: | LOWER PAPER FEED GUIDE ASSY |
| Парткод: | RM1-6263-000 |
| Деталь: | PAPER FEED GUIDE ASSY |
| Парткод: | RM1-6270-000 |
| Деталь: | POSITION GUIDE ASSY |
| Парткод: | RM1-6273-000 |
| Деталь: | H.V. POWER SUPPLY PCB ASSY |
| Парткод: | RM1-6280-000 |
| Деталь: | TOP SENSOR PCB ASSY |
| Парткод: | FM4-5038-000 |
| Деталь: | TOP SENSOR PCB ASSY |
| Парткод: | FM0-4631-000 |
| Деталь: | PAPER WIDTH SENSOR PCB ASSY |
| Парткод: | FM4-5673-000 |
| Деталь: | PAPER WIDTH SENSOR PCB ASSY |
| Парткод: | FM0-4633-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-3101-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | TRAY SENSOR PCB ASSY |
| Парткод: | FM4-5674-000 |
| Деталь: | TRAY SENSOR PCB ASSY |
| Парткод: | FM0-4634-000 |
| Деталь: | FIXING MOTOR ASSY |
| Парткод: | RM1-6296-000 |
| Деталь: | PAPER DELIVERY ROLLER ASSY |
| Парткод: | RM1-6301-000 |
| Деталь: | FACE-DOWN ROLLER ASSY |
| Парткод: | RM1-6311-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, TAP, M3X6 |
| Парткод: | XA9-1503-000 |
| Цена: | 340 ₽ |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | MOTOR, DC |
| Парткод: | RM1-6342-000 |
| Деталь: | INTERNAL COMPONENTS 6 |
| Парткод: | NPN |
Коды ошибок
E000 0000
E001 0000
E001 0001
E003 0000
E003 0001
E004 0000
E012 0000
E012 0001
E014 0000
E014 0001
E066 0000
E06F 0068
E100 0000
E110 0000
E196 0000
E196 0003
E245 1011
E245 1012
E245 1013
E245 1021
E245 1022
E245 1023
E245 2012
E245 2022
E602 0001
E602 0002
E602 0006
E602 0007
E602 0008
E602 0009
E602 1102
E602 1112
E602 1113
E602 1302
E602 1312
E602 1313
E602 1602
E602 1612
E602 1613
E604 0000
E616 0001
E721 0001
E730 C000
E730 C001
E730 D000
E730 D001
E733 0001
E733 0003
E733 0004
E733 0006
E740 0002
E740 0004
E744 0900
E744 1000
E744 1100
E748 2012
E748 4000
E748 4020
E760 0000
E805 0001
E805 0002
E808 0001
Описание
| Error code: | E000 0000 |
| Description: | Error in temperature rising of Fixing Assembly |
| Causes: | Temperature of the Fixing Assembly did not reach a certain temperature within the specified period of time. |
| Remedy: | 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB. |
| Error code: | E001 0000 |
| Description: | Abnormal high temperature of Fixing Assembly |
| Causes: | It was detected that the temperature of the Fixing Assembly was abnormally high. |
| Remedy: | 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB. |
| Error code: | E001 0001 |
| Description: | Abnormal high temperature in fixing (The sub thermistor detected a temperature of higher than 290 degree C. |
| Causes: | Abnormally high temperature detected by sub thermistor (sub thermistor triggered) |
| Remedy: | 1) Reconnect the connector on the Engine Controller PCB. 2) Turn OFF the power supply switch, and remove the Fixing Assembly. Measure the resistance value between the connector (FSRTH) at the Fixing Assembly side and grounding. If the resistance value is 1k ohm or lower, replace the Fixing Assembly. 3) Replace the Engine Controller PCB. |
| Error code: | E003 0000 |
| Description: | Abnormal low temperature of Fixing Assembly |
| Causes: | It was detected that the temperature of the Fixing Assembly was abnormally low. |
| Remedy: | 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB. |
| Error code: | E003 0001 |
| Description: | Abnormal low temperature in fixing (The sub thermistor detected a temperature of lower than 80 degree C for more than 2 seconds when 20 seconds elapsed after start of the power distribution to the heater.) |
| Causes: | Temperature drop detected by sub thermistor after attaining the target temperature (sub thermistor triggered) |
| Remedy: | 1) Reconnect the connector on the Engine Controller PCB. 2) Turn OFF the power supply switch, and remove the Fixing Assembly. Measure the resistance value between the connector (FSRTH) at the Fixing Assembly side and grounding. If the resistance value is not between 368k ohm and 512k ohm (normal temperature), replace the Fixing Assembly. 3) If there is no induction between the connector (ACN) at the Fixing Assembly side and the connector (ACH) while the assembly is removed, replace the assembly. 4) Replace the Engine Controller PCB. |
| Error code: | E004 0000 |
| Description: | Error in fixing power supply drive circuit |
| Causes: | Failed to detect the zero cross signal for the specified period of time or more. |
| Remedy: | 1. Check the connection of connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB. |
| Error code: | E012 0000 |
| Description: | Black drum motor error (Failure in drum motor initial operation) The target speed was not reached within a specified time after startup of the motor. |
| Causes: | Error in attaining the target ITB motor rotation detected based on ITB motor speed detection signal after ITB motor is actuated. |
| Remedy: | 1) Reconnect the connector on the Main Motor 2) Replace the Engine Controller PCB. |
| Error code: | E012 0001 |
| Description: | Black drum motor error (Failure in drum motor rotation) The motor rotated out of the target speed during rotation after the target speed was reached. |
| Causes: | Error in ITB motor rotation after attaining the target rotation detected based on ITB motor speed detection signal |
| Remedy: | 1) Reconnect the connector on the Main Motor 2) Replace the Engine Controller PCB. |
| Error code: | E014 0000 |
| Description: | Error in startup of the Main Motor |
| Causes: | Revolution of the Main Motor did not reach the specified value. |
| Remedy: | 1. Check the connection of connector between the Main Motor and the Engine Controller PCB. 2. Replace the Main Motor. 3. Replace the Engine Controller PCB. |
| Error code: | E014 0001 |
| Description: | Fixing Motor rotation error |
| Causes: | Error in fixing motor rotation after attaining the target rotation detected based on fixing motor speed detection signal. |
| Remedy: | 1) Reconnect the connector on the Fixing Motor 2) Replace the Fixing Motor |
| Error code: | E066 0000 |
| Description: | Environment sensor failure |
| Causes: | Error in environment sensor |
| Remedy: | Replace the environment sensor. |
| Error code: | E06F 0068 |
| Description: | EEPROM access failure |
| Causes: | EEPROM communication error |
| Remedy: | Replace the EEPROM. |
| Error code: | E100 0000 |
| Description: | Laser Scanner Assembly error |
| Causes: | At the Laser Scanner Unit, BD cycle was not within the specified range. |
| Remedy: | 1. Check the connection of connector between the Main Controller PCB and the Laser Scanner Unit. 2. Check the connection of connector between the Relay PCB and the Laser Scanner Unit. 3. Replace the Laser Scanner Unit. |
| Error code: | E110 0000 |
| Description: | Optical assembly error (Scanner motor initial operation failure) |
| Causes: | Scanner failed to be ready after starting up pseudo-BD control |
| Remedy: | 1) Reconnect the connector on the Laser Scanner Unit. 2) Replace the Laser Scanner Unit. |
| Error code: | E196 0000 |
| Description: | DCON error |
| Causes: | Failed to update ROM of DC controller PCB |
| Remedy: | 1) Replace the Engine Controller PCB. |
| Error code: | E196 0003 |
| Description: | An Engine Controller which is not compatible with the Main Controller has been detected. |
| Causes: | EEPROM data in DCON could not be read at startup. |
| Remedy: | Replace the Engine Controller PCB. |
| Error code: | E245 1011 |
| Description: | Host machine FRAM write error |
| Remedy: | Replace the host machine FRAMs 1 and 2. |
| Error code: | E245 1012 |
| Description: | Host machine FRAM write error |
| Remedy: | Replace the host machine FRAMs 1 and 2. |
| Error code: | E245 1013 |
| Description: | Host machine FRAM write error |
| Remedy: | Replace the host machine FRAMs 1 and 2. |
| Error code: | E245 1021 |
| Description: | Host machine FRAM write error |
| Remedy: | Replace the host machine FRAMs 1 and 2. |
| Error code: | E245 1022 |
| Description: | Host machine FRAM write error |
| Remedy: | Replace the host machine FRAMs 1 and 2. |
| Error code: | E245 1023 |
| Description: | Host machine FRAM write error |
| Remedy: | Replace the host machine FRAMs 1 and 2. |
| Error code: | E245 2012 |
| Description: | FLASH write error |
| Causes: | System error |
| Remedy: | Replace the FLASH PCB. |
| Error code: | E245 2022 |
| Description: | FLASH write error |
| Causes: | System error |
| Remedy: | Replace the FLASH PCB. |
| Error code: | E602 0001 |
| Description: | Insufficient HDD capacity |
| Remedy: | Replace the HDD. |
| Error code: | E602 0002 |
| Description: | Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged. |
| Causes: | Bootable load failure |
| Remedy: | Burn the Bootable CD again. |
| Error code: | E602 0006 |
| Description: | Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged. |
| Remedy: | Burn the Bootable CD again. |
| Error code: | E602 0007 |
| Description: | The contents cannot be detected. |
| Remedy: | Create Bootable again. |
| Error code: | E602 0008 |
| Description: | There is not enough free space in the alternative block of NAND Flash |
| Causes: | Remaining memory area in the flash is small. |
| Remedy: | 1) Start service mode. 2) Clear the error from the service mode menu. 3) Reboot the machine to stop the error code. 4) Export the user information from the old NAND Flash. 5) Replace the Controller Board. (Change the NAND Flash.) 6) Import the user information to the new NAND Flash. |
| Error code: | E602 0009 |
| Description: | The power supply was interrupted due to power failure or disconnection of the power plug. The MEAP area in the Flash ROM (NAND ROM) became read-only and cannot be written. MEAP cannot be started. |
| Causes: | MEAP cannot be started due to an error caused by invalid power down. |
| Remedy: | Initialize the MEAP area in Flash ROM (NAND ROM) by enabling the MEAP recovery menu from service mode or special management mode and rebooting the machine. Since the installed MEAP applications and their management information are all cleared, MEAP needs to be reinstalled. |
| Error code: | E602 1102 |
| Description: | /APL_MEAP error (The file systemcannot be initialized properly.) |
| Causes: | File system could not be initialized normally (MEAP-related). |
| Error code: | E602 1112 |
| Description: | /APL_MEAP error (device access error EROFS) |
| Causes: | Device access error (MEAP-related). |
| Error code: | E602 1113 |
| Description: | /APL_MEAP error (device access error EIO) |
| Causes: | Device access error (MEAP-related). |
| Error code: | E602 1302 |
| Description: | /APL_KEEP error (The file systemcannot be initialized properly.) |
| Causes: | File system could not be initialized normally |
| Error code: | E602 1312 |
| Description: | /APL_KEEP error (device access error EROFS) |
| Causes: | Device access error |
| Error code: | E602 1313 |
| Description: | /APL_KEEP error (device access error EIO) |
| Causes: | Device access error |
| Error code: | E602 1602 |
| Description: | /APL_CDS error (The file systemcannot be initialized properly.) |
| Causes: | File system could not be initialized normally (CDS-related). |
| Error code: | E602 1612 |
| Description: | /APL_CDS error (device access error EROFS) |
| Causes: | Device access error (CDS-related). |
| Error code: | E602 1613 |
| Description: | /APL_CDS error (device access error EIO) |
| Causes: | Device access error (CDS-related). |
| Error code: | E604 0000 |
| Description: | Memory capacity error ?(Lack of memory capacity?) |
| Causes: | Lack of memory capacity |
| Remedy: | Check the memory capacity inserted to each slot. |
| Error code: | E616 0001 |
| Description: | Installed MEAP applications have been deleted. |
| Causes: | MEAP application is lost. |
| Error code: | E721 0001 |
| Description: | Printer engine which is not supported by the controller is connected.Printer engine of a different model is connected. |
| Remedy: | Connect with the printer engine appropriate to the model. |
| Error code: | E730 C000 |
| Description: | The memory cannot be obtained at initialization. |
| Causes: | An error, such as failure in memory retrieval at initialization, occurred. |
| Remedy: | Turn OFF and then ON the power. |
| Error code: | E730 C001 |
| Description: | An error occurred when accessing the HDD. |
| Causes: | An error occurred when accessing the controller. |
| Remedy: | Turn OFF and then ON the power. |
| Error code: | E730 D000 |
| Description: | The memory cannot be obtained at initialization. |
| Causes: | An error, such as failure in memory retrieval at initialization, occurred. |
| Remedy: | Turn OFF and then ON the power. |
| Error code: | E730 D001 |
| Description: | An error occurred when accessing the HDD. |
| Causes: | System error |
| Remedy: | Turn OFF and then ON the power. |
| Error code: | E733 0001 |
| Description: | Error in printer communication (illegal communication after establishing communication, parity error) |
| Causes: | Communication error occurred after normal startup. |
| Remedy: | 1) Turn OFF and then ON the power. 2) Replace the Engine Controller PCB. |
| Error code: | E733 0003 |
| Description: | Error in printer communication (mismatch of country setting) |
| Remedy: | 1) Turn OFF and then ON the power. 2) Replace the Engine Controller PCB. |
| Error code: | E733 0004 |
| Description: | Error in printer communication (undefined command error) |
| Causes: | Command error |
| Remedy: | 1) Turn OFF and then ON the power. 2) Replace the Engine Controller PCB. |
| Error code: | E733 0006 |
| Description: | Error in printer communication (unknown communication error) |
| Causes: | An unknown communication error |
| Remedy: | 1) Turn OFF and then ON the power. 2) Replace the Engine Controller PCB. |
| Error code: | E740 0002 |
| Description: | An invalid MAC address has been detected. |
| Causes: | Detected the injustice of the Mac address |
| Remedy: | 1) Check the Mac address. 2) Write the address to the Mac address. 3) Replace the board. |
| Error code: | E740 0004 |
| Description: | LAN Controller Chip access error |
| Remedy: | 1) Check around the LAN Chip. 2) Replace the board. |
| Error code: | E744 0900 |
| Description: | Model code mismatch |
| Remedy: | Change to proper bootable. Check the supported series or model of the firmware, and burn the correct series or model of firmware. Replace the Main Controller Board. |
| Error code: | E744 1000 |
| Description: | Mismatch of the series or model of the firmware sent at the time of downloading |
| Causes: | Mismatch of the model for which the firmware was downloaded is detected. |
| Remedy: | Change to proper bootable. Check the supported series or model of the firmware, and burn the correct series or model of firmware. Replace the Main Controller Board. |
| Error code: | E744 1100 |
| Description: | Falsification of the Main Controller Board has been detected. |
| Causes: | System error |
| Remedy: | Change to proper bootable. Check the supported series or model of the firmware, and burn the correct series or model of firmware. Replace the Main Controller Board. |
| Error code: | E748 2012 |
| Description: | Failed to rewrite due to no more alternative block of Flash ROM (NAND) available. |
| Causes: | System error |
| Remedy: | Replace the Controller board. |
| Error code: | E748 4000 |
| Description: | G-Chip loopback ended in timeout. |
| Remedy: | Replace the Main Controller |
| Error code: | E748 4020 |
| Description: | Unknown device has been detected on PCI. |
| Remedy: | Replace the Controller board. |
| Error code: | E760 0000 |
| Description: | CPU exception occurred. |
| Causes: | An error due to the controller software occurred so that print could not be proceeded. |
| Remedy: | Turn on the power again. |
| Error code: | E805 0001 |
| Description: | Fan1 failure |
| Causes: | • FAN driving: When "Lock signal = High" is detected more than 5 sec or more continuously. • FAN suspended: When "Lock signal = Low" is detected more than 10 sec or more continuously. |
| Remedy: | Replace the Fan1 |
| Error code: | E805 0002 |
| Description: | Fan2 failure |
| Causes: | • FAN driving: When "Lock signal = High" is detected more than 5 sec or more continuously. • FAN suspended: When "Lock signal = Low" is detected more than 10 sec or more continuously. |
| Remedy: | Replace the Fan2 |
| Error code: | E808 0001 |
| Description: | Low-voltage power supply failure |
| Causes: | Failure detection of Low Voltage Power Supply PCB |
| Remedy: | Replace the Low-voltage power supply unit. |
