Canon imageRUNNER LBP5280
Рейтинг
Модули
103 INTERNAL COMPONENTS 3
105 INTERNAL COMPONENTS 5
102 INTERNAL COMPONENTS 2
900 MAIN CONTOROLLER PCB ASSY
300 CASSETTE
101 INTERNAL COMPONENTS 1
104 INTERNAL COMPONENTS 4
530 INTERMEDIATE TRANS. BELT ASSY
460 LASER SCANNER ASSY
106 INTERNAL COMPONENTS 6
100 EXTERNAL COVERS, PANELS, ETC.
810 FIXING ASSY
Детали 104 INTERNAL COMPONENTS 4
Деталь: | REGISTRATION ASSY |
Парткод: | FM4-8513-000 |
Деталь: | COVER, HOLDER |
Парткод: | RC2-2014-000 |
Деталь: | PAD, SEPARATION |
Парткод: | RL1-1785-000 |
Деталь: | PICK-UP ROLLER ASSY |
Парткод: | RM1-4426-000 |
Деталь: | MP PAPER PICK-UP ASSY |
Парткод: | FM4-8514-000 |
Деталь: | SEPARATION ROLLER ASSY |
Парткод: | RM1-4840-000 |
Деталь: | PAPER PICK-UP ASSY |
Парткод: | FM4-8511-000 |
Деталь: | MP CLUTCH ASSY |
Парткод: | RM1-5428-000 |
Деталь: | IC, PHOTO INTERRUPTER |
Парткод: | WG8-5935-000 |
Деталь: | SCREW, D, M3X6 |
Парткод: | XA9-1835-000 |
Деталь: | SCREW, D, M3X8 |
Парткод: | XA9-1671-000 |
Цена: | 170 ₽ |
Деталь: | LABEL, MOTOR CAUTION |
Парткод: | FC8-8748-000 |
Деталь: | SHEET, GUIDE, RIGHT |
Парткод: | FC0-3944-000 |
Деталь: | ARM, TRAY, LEFT |
Парткод: | RC2-3386-000 |
Деталь: | ARM, TRAY, RIGHT |
Парткод: | RC2-3387-000 |
Деталь: | ARM, TRAY |
Парткод: | RC2-3388-000 |
Деталь: | SHEET, GUIDE, LEFT |
Парткод: | FC0-3943-000 |
Деталь: | INTERNAL COMPONENTS 3 |
Парткод: | NPN |
Деталь: | SCREW, D, M3X8 |
Парткод: | XA9-1671-000 |
Цена: | 170 ₽ |
Деталь: | PAPER DELIVERY ASSY |
Парткод: | FM4-8515-000 |
Деталь: | FIXING MOTOR UNIT |
Парткод: | RM1-4896-000 |
Деталь: | POWER SUPPLY SUB PCB ASSY |
Парткод: | RM1-7355-000 |
Деталь: | REGISTRATION MOTOR ASSY |
Парткод: | RM1-5419-000 |
Деталь: | SCREW, TP, M3X6 |
Парткод: | XA9-1418-000 |
Деталь: | FUSER CABLE ASSY |
Парткод: | RM1-7356-000 |
Деталь: | SCREW, MACH., FLAT HEAD, M3X4 |
Парткод: | XA9-0679-000 |
Деталь: | SCREW, D, M3X6 |
Парткод: | XA9-1835-000 |
Деталь: | COVER, REAR, UPPER |
Парткод: | FC0-3882-000 |
Деталь: | DIMM, SMD-E51288HG-6E, SDRAM |
Парткод: | FK2-8341-000 |
Деталь: | INTERNAL COMPONENTS 5 |
Парткод: | NPN |
Деталь: | ROLLER, PAPER PICK-UP |
Парткод: | RL1-1802-000 |
Деталь: | COLOR MISREGIST. SENSOR ASSY |
Парткод: | RM1-4850-000 |
Деталь: | SCREW, D, M3X8 |
Парткод: | XA9-1671-000 |
Цена: | 170 ₽ |
Деталь: | MP SOLENOID ASSY |
Парткод: | RM1-5420-000 |
Деталь: | HINGE, MULTI-PURPOSE COVER |
Парткод: | RC2-3395-000 |
Деталь: | BUSHING |
Парткод: | RC2-3396-000 |
Деталь: | INTERNAL COMPONENTS 2 |
Парткод: | NPN |
Деталь: | IC, T6TH5EFG-0002(0), STANDARD |
Парткод: | FK2-7852-000 |
Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
Парткод: | FM0-3418-000 |
Деталь: | CASSETTE |
Парткод: | FM4-8504-000 |
Деталь: | TEMPERATURE SENSOR UNIT |
Парткод: | RK2-3267-000 |
Деталь: | CARTRIDGE TRAY ASSY |
Парткод: | RM1-4836-000 |
Деталь: | H. V. POWER SUPPLY PCB ASSY |
Парткод: | RM1-5294-050 |
Деталь: | SD SLOT EXTENSION PCB ASSEMBLY |
Парткод: | FM4-8869-000 |
Деталь: | ENV. SENSOR CABLE ASSY |
Парткод: | RM1-5399-000 |
Деталь: | SENSOR CABLE ASSY |
Парткод: | RM1-5398-000 |
Деталь: | IC, PHOTO INTERRUPTER |
Парткод: | WG8-5935-000 |
Деталь: | SCREW, W/WASHER, M3X8 |
Парткод: | XA9-1420-000 |
Цена: | 1 100 ₽ |
Деталь: | SCREW, D, M3X6 |
Парткод: | XA9-1835-000 |
Деталь: | SCREW, D, M3X8 |
Парткод: | XA9-1671-000 |
Цена: | 170 ₽ |
Деталь: | RAIL, LEFT |
Парткод: | RC2-3800-000 |
Деталь: | RAIL, RIGHT |
Парткод: | RC2-3801-000 |
Деталь: | CABLE, FLAT |
Парткод: | FK3-2249-000 |
Деталь: | CABLE, USB |
Парткод: | FK3-1797-000 |
Деталь: | PLATE, GROUNDING |
Парткод: | FC0-3919-000 |
Деталь: | GUIDE |
Парткод: | FC0-3905-000 |
Деталь: | MEMORY PCB ASSEMBLY |
Парткод: | FM4-8868-000 |
Деталь: | INTERNAL COMPONENTS 1 |
Парткод: | NPN |
Деталь: | DC CONTROLLER PCB ASSY |
Парткод: | FM4-9356-000 |
Деталь: | CABLE, FLAT |
Парткод: | RK2-2302-000 |
Деталь: | CABLE, FLAT |
Парткод: | FK3-2146-000 |
Деталь: | MOTOR, DC |
Парткод: | RL1-1800-000 |
Деталь: | MOTOR, DC |
Парткод: | RL1-3053-000 |
Деталь: | DRIVER PCB ASSY |
Парткод: | FM4-9372-000 |
Деталь: | RELAY PCB ASSY |
Парткод: | RM1-5293-000 |
Деталь: | INLET CABLE ASSY |
Парткод: | RM1-5368-000 |
Деталь: | SENSOR CABLE ASSY |
Парткод: | RM1-5385-000 |
Деталь: | DRAM MOTOR CABLE ASSY |
Парткод: | RM1-5393-000 |
Деталь: | DEVELOPING MOTOR CABLE ASSY |
Парткод: | RM1-5394-000 |
Деталь: | FEED MOTOR CABLE ASSY |
Парткод: | RM1-5395-000 |
Деталь: | SENSOR CABLE ASSY |
Парткод: | RM1-5400-000 |
Деталь: | POWER SUPPLY ASSY |
Парткод: | FM4-9357-000 |
Деталь: | OPTION CABLE ASSY |
Парткод: | RM1-5434-000 |
Деталь: | RLD CABLE ASSY |
Парткод: | RM1-5435-000 |
Деталь: | HOLDER, CARTRIDGE DOOR SENSOR |
Парткод: | RC2-3220-000 |
Деталь: | FIXING MOTOR CABLE ASSY |
Парткод: | RM1-5438-000 |
Деталь: | IC, PHOTO INTERRUPTER |
Парткод: | WG8-5935-000 |
Деталь: | SCREW, MACH., FLAT HEAD, M3X4 |
Парткод: | XA9-0679-000 |
Деталь: | SCREW, W/WASHER, M3X8 |
Парткод: | XA9-1420-000 |
Цена: | 1 100 ₽ |
Деталь: | SCREW, D, M3X6 |
Парткод: | XA9-1835-000 |
Деталь: | SCREW, D, M3X8 |
Парткод: | XA9-1671-000 |
Цена: | 170 ₽ |
Деталь: | SCREW, TP, M3X6 |
Парткод: | XA9-1418-000 |
Деталь: | ARM, DOOR SENSOR |
Парткод: | RC2-3221-000 |
Деталь: | MAIN DRIVE ASSY |
Парткод: | RM1-8042-010 |
Деталь: | EVERYNIGHT POWER PCB ASSEMBLY |
Парткод: | FK3-1986-000 |
Цена: | 3 900 ₽ |
Деталь: | AC CONNECTING PCB ASSEMBLY |
Парткод: | FM4-9361-000 |
Деталь: | INTERNAL COMPONENTS 4 |
Парткод: | NPN |
Деталь: | INTERMEDIATE TRANS. BELT ASSY |
Парткод: | RM1-4852-000 |
Деталь: | LASER SCANNER ASSY |
Парткод: | FM4-3359-000 |
Цена: | 32 000 ₽ |
Деталь: | COVER, REAR, LOWER |
Парткод: | FC0-3881-000 |
Деталь: | CONNECTOR, SNAP TIGHT |
Парткод: | VS1-7584-006 |
Деталь: | REAR DOOR ASSY |
Парткод: | FM4-8503-000 |
Деталь: | LINK, DOOR |
Парткод: | RC2-3750-000 |
Деталь: | LINK, GUIDE |
Парткод: | RC2-3752-000 |
Деталь: | CAP, LINK |
Парткод: | RC2-3774-000 |
Деталь: | FAN |
Парткод: | RK2-2276-000 |
Деталь: | PAPER FEED GUIDE ASSY |
Парткод: | RM1-4838-000 |
Деталь: | REAR DOOR RIB ASSY |
Парткод: | RM1-4876-000 |
Деталь: | PAPER RE-PICK UP GUIDE ASSY |
Парткод: | RM1-4877-000 |
Деталь: | DUPLEXING FEED GUIDE ASSY |
Парткод: | RM1-4879-000 |
Деталь: | REVERSE DRIVE ASSY |
Парткод: | RM1-4880-000 |
Деталь: | SCREW, D, M3X8 |
Парткод: | XA9-1671-000 |
Цена: | 170 ₽ |
Деталь: | LABEL, JAM CLEARING |
Парткод: | FU7-8873-000 |
Деталь: | INTERNAL COMPONENTS 6 |
Парткод: | NPN |
Деталь: | COVER, RIGHT FRONT |
Парткод: | FC0-3865-000 |
Цена: | 800 ₽ |
Деталь: | BUTTON, POWER |
Парткод: | FC0-3866-000 |
Цена: | 260 ₽ |
Деталь: | PANEL, RIGHT |
Парткод: | FC0-3873-000 |
Деталь: | COVER, RIGHT |
Парткод: | FC0-3874-000 |
Деталь: | COVER, LEFT |
Парткод: | FC0-3879-000 |
Деталь: | COVER, TOP, FRONT |
Парткод: | FC0-3870-000 |
Деталь: | COVER, TOP, REAR |
Парткод: | FC0-3871-000 |
Деталь: | CONTROL PANEL ASSY |
Парткод: | FM4-8508-000 |
Деталь: | FRONT DOOR ASSY |
Парткод: | FM4-8501-000 |
Деталь: | BUTTON, TEST PRINT SWITCH |
Парткод: | RC2-3719-000 |
Деталь: | LABEL, PAPER SIZE |
Парткод: | FC8-8742-000 |
Деталь: | FAN |
Парткод: | RK2-2276-000 |
Деталь: | COVER, USB INNER |
Парткод: | FC0-3878-000 |
Деталь: | COVER, USB |
Парткод: | FC0-3888-000 |
Деталь: | COVER, DIMM ASSY |
Парткод: | FC0-3875-000 |
Деталь: | SCREW, D, M3X8 |
Парткод: | XA9-1671-000 |
Цена: | 170 ₽ |
Деталь: | EXTERNAL COVERS, PANELS, ETC. |
Парткод: | NPN |
Деталь: | FIXING FILM ASSEMBLY |
Парткод: | FM4-3062-000 |
Деталь: | LABEL, CAUTION |
Парткод: | FC8-8743-000 |
Деталь: | ROLLER, PRESSURE |
Парткод: | RC2-3367-000 |
Цена: | 5 000 ₽ |
Деталь: | PHOTO INTERRUPTER, TLP1243 |
Парткод: | WG8-5696-000 |
Деталь: | FIXING ASSY (220-240V) |
Парткод: | FM3-8295-000 |
Коды ошибок
E000-0000
E001-0000
E001-0001
E003-0000
E003-0001
E004-0000
E012-0000
E012-0001
E014-0000
E014-0001
E015-0001
E020-0000
E021-0003
E021-0007
E066-0000
E06F-0068
E070-0000
E078-0001
E100-0000
E100-0001
E100-0002
E100-0003
E110-0002
E194-0000
E196-0000
E196-0002
E197-0001
E198-0000
E245
E246
E247
E350
E602-0002
E602-0003
E602-0006
E602-0008
E602-1102
E602-1112
E602-1113
E602-1302
E602-1312
E602-1313
E602-1602
E602-1612
E602-1613
E604-0000
E604-0001
E616-0001
E730-100A
E730-C000
E730-C001
E730-D000
E730-D001
E733-0000
E733-0001
E733-0004
E733-0006
E740-0002
E740-0004
E748-2012
E748-4000
E748-4020
E760-0000
E805-0001
E805-0003
E805-0005
E808-0001
E840-0000
Описание
Error code: | E000-0000 |
Description: | Startup error The temperature detected by the main or sub thermistor does not rise to the specified value during startup control. |
Causes: | The detection temperature of the main thermistor did not increase after start of the power distribution to the heater. |
Remedy: | - Check the fixing film connector. - Replace the fixing film unit. - Replace the DC controller PCB. |
Error code: | E001-0000 |
Description: | Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control |
Causes: | The main thermistor detected a temperature of higher than 255 degree C. |
Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
Error code: | E001-0001 |
Description: | Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control. |
Causes: | The sub thermistor detected a temperature of higher than 290 degree C. |
Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
Error code: | E003-0000 |
Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
Error code: | E003-0001 |
Description: | Abnormally low temperature (detected by sub thermistor) After the temperature detected by the sub thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
Causes: | The sub thermistor detected a temperature of lower than 80 degree C for more than 2 seconds when 20 seconds elapsed after start of the power distribution to the heater. |
Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
Error code: | E004-0000 |
Description: | Fixing power supply drive circuit error |
Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
Error code: | E012-0000 |
Description: | Error in ITB motor activation. |
Causes: | The cycle of ITB motor speed detection signal does not move in the specified cycle after ITB motor drive is started. Cause Failure in ITB motor, failure in DC controller PCB |
Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
Error code: | E012-0001 |
Description: | Error in ITB motor activation. |
Causes: | If the ITB motor speed detection signal comes off the specified cycle after it turned once to the specified cycle. Cause Failure in ITB motor, failure in DC controller PCB. |
Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
Error code: | E014-0000 |
Description: | Fixing motor failure |
Causes: | Fixing motor startup error The target speed was not reached within a specified time after startup of the motor. |
Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
Error code: | E014-0001 |
Description: | Fixing motor failure |
Causes: | Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached. |
Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
Error code: | E015-0001 |
Description: | Cassette 1 lift up motor error |
Causes: | Cassette 1 lift up motor error |
Remedy: | Reconnect the connector J151 on the DC controller PCB and the relay connector J742. Check the cassette media stack surface sensor in the sensor monitor mode. If a failure is found, replace the lifter drive unit. Replace the lifter drive unit. |
Error code: | E020-0000 |
Description: | Density sensor failure warning |
Error code: | E021-0003 |
Description: | Error in developing motor |
Causes: | Motor (Bk) rotation error |
Error code: | E021-0007 |
Description: | Error in developing motor |
Causes: | Error in startup of the Motor (Bk) |
Error code: | E066-0000 |
Description: | Environment sensor failure |
Causes: | Environment sensor failure |
Remedy: | Replace the environment sensor. |
Error code: | E06F-0068 |
Description: | EEPROM access failure |
Causes: | EEPROM access failure |
Remedy: | Replace the EEPROM. |
Error code: | E070-0000 |
Description: | Error in ITB / TOP sensor |
Causes: | Error in ITB / TOP sensor Cause: Problem in ITB / TOP sensor / DC controller PCB |
Remedy: | • Check connectors of ITB unit and DC controller PCB. • Replace ITB units • Replace DC controller PCBs |
Error code: | E078-0001 |
Description: | Primary transfer disengagement mechanism failure |
Causes: | Primary transfer disengagement mechanism failure At the time of searching the home position: Considering that the coupling of primary transfer engagement/ disengagement drive may not be connected, the solenoid was pulled for maximum 6 times in the condition where the flag was detected once. But the HP sensor did not detect the color print engagement position. * If a flag is not detected even once, it is considered that the ITB unit is absent. At the time of changing the position The position after turning ON/OFF of the solenoid did not match the HP sensor value. |
Remedy: | Check whether the ITB unit is installed or not. Reconnect the connector J181 on the DC controller PCB. Check the primary transfer roller disengagement switch in the sensor monitor mode. If a failure is found, replace the primary transfer roller disengagement switch assembly. Execute the primary transfer roller engagement/disengagement drive test in the actuator drive mode. If the primary transfer roller does not perform engagement/disengagement, replace the fixing drive unit. |
Error code: | E100-0000 |
Description: | BD detection PCB failure The BD detection PCB is faulty. |
Causes: | Yellow optical assembly failure |
Remedy: | - Check the connector of the BD detection PCB. - Replace the laser scanner unit. - Replace the DC controller PCB. |
Error code: | E100-0001 |
Description: | Error detection on any of scanner motor, laser unit, and BD detection at scanner area. |
Causes: | Magenta optical assembly failure |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board. |
Error code: | E100-0002 |
Description: | Optical assembly error (Laser) |
Causes: | Cyan optical assembly failure |
Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
Error code: | E100-0003 |
Description: | Optical assembly error (Laser) |
Causes: | Black optical assembly failure |
Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
Error code: | E110-0002 |
Description: | Error in first artificial BD adjustment |
Causes: | Primary pseudo BD correction |
Error code: | E194-0000 |
Description: | Error in CPR sensor |
Causes: | If CPR sensor is judged error. Cause Soiling in density detection sensor, failure in density detection sensor, failure in DC controller PCB, failure in toner cartridge. |
Remedy: | - Check the connector of DC controller PCB - Replace the ITB unit - Replace the DC controller PCB - Replace the toner cartridge |
Error code: | E196-0000 |
Description: | Invalid RFU execution requested |
Causes: | D-con update for the host machine or the optional cassette is not completed. |
Error code: | E196-0002 |
Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (option ROM). |
Causes: | Can not access to DC controller NVRAM Cause Failure in DC controller PCB |
Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
Error code: | E197-0001 |
Description: | Engine communication error |
Causes: | Error between DC controller PCB and main controller PCB. Cause Failure in connection between PCB, failure in DC controller PCB, failure in controller PCB. |
Remedy: | - Check the connection of the connector of the DC controller PCB and controller PCB - Replace the DC controller PCB - Replace the controller PCB |
Error code: | E198-0000 |
Description: | DC controller memory failure |
Causes: | A checksum failure is found in the block where specific information of the DC controller PCB is saved. A communication error occurred when reading the specific information of the DC controller PCB from the NVRAM at power-on. |
Remedy: | If the failure cannot be removed by turning the power OFF/ON, replace the DC controller PCB. |
Error code: | E245 |
Description: | System Error |
Causes: | System Error |
Remedy: | Contact the sales companies. |
Error code: | E246 |
Description: | System Error |
Causes: | System Error |
Remedy: | Contact the sales companies. |
Error code: | E247 |
Description: | System Error |
Causes: | System Error |
Remedy: | Contact the sales companies. |
Error code: | E350 |
Description: | 4th drawer transport jam (paper not reaching 2nd drawer transport sensor): Paper which has passed the 3rd drawer / Tandem LCF transport sensor does not reach the 2nd drawer transport sensor during the feeding at the 4th drawer. |
Causes: | 3rd drawer transport clutch 2nd drawer transport sensor Feed motor PFC board Rollers |
Remedy: | Open the feed cover. Is there paper in front of the 2nd drawer transport sensor? ↓ → YES → If the paper is damaged, remove the paper and check the followings 1. Check if the paper is skewed, and correct it if it is skewed. 2. Check the paper amount. 3. Check if the paper is not the one with printing on its back side. 4. Check if the width of the side guides of the drawer is too narrow. NO Is the 2nd drawer transport sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[2]/[C] ↓ → NO → 1. Check if the connector of the 2nd drawer transport sensor is disconnected. 2. Check if the connector CN329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the 2nd drawer transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-210/225/231) ↓ → NO → 1. Check if the connectors of the (lower/middle) transport clutches are disconnected. 2. Check if the connector CN329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open circuited. 4. Check if the conductor pattern on the LGC board is short circuited or open circuited. 5. Replace the (lower/middle) transport clutches. 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and clean or replace them. 2. Check the transport roller. Clean or replace it. |
Error code: | E602-0002 |
Description: | HDD error |
Causes: | Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged. |
Remedy: | Burn the Bootable CD again. |
Error code: | E602-0003 |
Description: | HDD error |
Causes: | HDD access error An error occurred caused by the device or hardware when accessing to the HDD during execution of bootrom. (Damage to the sector / Busy device status, etc.) |
Remedy: | Turn on the power again. |
Error code: | E602-0006 |
Description: | HDD error |
Causes: | SubBootable load failure A SubBootable CD was not contained. A SubBootable CD was damaged. |
Remedy: | Burn the SubBootable CD again. |
Error code: | E602-0008 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | Alternative block of flash memory is almost depleted. |
Remedy: | Perform the following procedure to replace the the Main Controller PCB and export/import user information. 1. Export user information from the flash memory of the old Main Controller PCB (before replacement). 2. Replace the Main Controller PCB. Import user information to the flash memory of the new Main Controller PCB (after replacement). |
Error code: | E602-1102 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | Error detection of file system (LBP7680Cx only) |
Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. If E616-0001 occurs at restart after turning OFF and then ON the power, execute the following procedures. 1. Initialize MEAP area, and install MEAP application again. (Refer to the remedy for E616-0001.) 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E602-1112 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | Device access error (LBP7680Cx only) |
Remedy: | Execute the following procedures. If E616- 0001 occurs after turning OFF and then ON the power (procedure 1), install MEAP application again by following the remedy for E616-0001 first. Then, execute the procedure 2. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E602-1113 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | Device access error (LBP7680Cx only) |
Remedy: | Execute the following procedures. If E616- 0001 occurs after turning OFF and then ON the power (procedure 1), install MEAP application again by following the remedy for E616-0001 first. Then, execute the procedure 2. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E602-1302 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | File system initialization error (LBP7680Cx only) |
Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E602-1312 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | Device access error (LBP7680Cx only) |
Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E602-1313 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | Device access error (LBP7680Cx only) |
Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E602-1602 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | File system initialization error (LBP7680Cx only) |
Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E602-1612 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | Device access error (LBP7680Cx only) |
Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E602-1613 |
Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
Causes: | Device access error (LBP7680Cx only) |
Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
Error code: | E604-0000 |
Description: | Memory error |
Causes: | Lack of memory capacity |
Remedy: | Check the memory capacity inserted to each slot. |
Error code: | E604-0001 |
Description: | Insufficient memory capacity |
Causes: | Failed to allocate the memory required to start PDL. |
Remedy: | - Remove and then install the additional memory. - Replace the additional memory with a correct one. - Turn OFF and then ON the power. - Replace the Controller PCB. |
Error code: | E616-0001 |
Description: | (LBP7680Cx only) |
Causes: | MEAP application was deleted by auto recovery at restart after E602-11XX. |
Remedy: | Initialize MEAP area in the flash memory with the following procedures, and install MEAP application again. 1. Initialize the MEAP area. Service Mode > FUNCTION GR. > MEAP > MEAP FUNCTION > ON 2. Install MEAP application again. |
Error code: | E730-100A |
Description: | Printer service call |
Error code: | E730-C000 |
Description: | An error such as memory not acquired at initialization occurred. |
Remedy: | Turn on the power again. |
Error code: | E730-C001 |
Description: | An error occurred when accessing the HDD. |
Remedy: | Turn on the power again. |
Error code: | E730-D000 |
Description: | Printer service call |
Causes: | An error, such as failure in memory retrieval at initialization, occurred. |
Remedy: | - Turn OFF and then ON the power. - Replace the Main Controller PCB. |
Error code: | E730-D001 |
Description: | Printer service call |
Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
Remedy: | Only LBP7680Cx is supported. |
Error code: | E733-0000 |
Description: | Erroneous communication between controller and printer Cannot communicate with the printer at startup. |
Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
Remedy: | - Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB. |
Error code: | E733-0001 |
Description: | Printer communication error (Invalid communication after communication is established, Parity error) |
Remedy: | Turn on the power again. Replace the DC controller PCB. |
Error code: | E733-0004 |
Description: | Printer communication error (Undefined command error) |
Remedy: | Turn on the power again. Replace the DC controller PCB. |
Error code: | E733-0006 |
Description: | Printer communication error (Unknown communication error) |
Remedy: | Turn on the power again. Replace the DC controller PCB. |
Error code: | E740-0002 |
Description: | Error detection on either Network Board or Mac address |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board. |
Error code: | E740-0004 |
Description: | LAN controller chip access error |
Remedy: | 1.Check the area around the LAN chip. 2.Replace the board. |
Error code: | E748-2012 |
Description: | Failed to rewrite due to no more alternative block of Flash ROM (NAND) available. |
Error code: | E748-4000 |
Description: | Timeout of G-Chip loop back |
Remedy: | Replace the main controller PCB. |
Error code: | E748-4020 |
Description: | Unknown device detected on the PCI |
Remedy: | Replace the main controller PCB. |
Error code: | E760-0000 |
Description: | CPU exception occurred. |
Remedy: | Turn on the power again. |
Error code: | E805-0001 |
Description: | Error in duplex cooling fan |
Causes: | Fan 1 failure |
Error code: | E805-0003 |
Description: | Fan failure |
Causes: | Controller fan failure detected The controller fan does not rotate because some kind of failure occurred in it. |
Remedy: | Replace the controller fan. |
Error code: | E805-0005 |
Description: | Error in duplex cooling fan |
Causes: | Duplex cooling fan can not rotate the specified number of rotations. Cause Failure in duplex cooling fan, failure in DC controller PCB |
Remedy: | - Check the connectors of duplex cooling fan and DC controller PCB - Replace the duplex cooling fan |
Error code: | E808-0001 |
Description: | Fixing Assembly_Edge Left Cooling Fan error |
Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Edge Left Cooling Fan. (2) Replace the DC Controller Board. |
Error code: | E840-0000 |
Description: | Pressure release mechanism failure |
Causes: | The target pressure position was not reached even when 3.5 seconds (approximately 1.5 rotation of the cam) elapsed after start of the fixing motor reverse rotation. |
Remedy: | Check the gears and detection flags related to fixing pressure release mechanism. Replace the fixing pressure release sensor (PS9). Replace the fixing motor. Replace the fixing assembly. |