Canon i-SENSYS LBP7660Cdn
Рейтинг
Модули
103 INTERNAL COMPONENTS 3
106 INTERNAL COMPONENTS 6
104 INTERNAL COMPONENTS 4
300 CASSETTE
330 TRANSFER MOUNT ASSEMBLY
100 EXTERNAL COVERS, PANELS, ETC.
101 INTERNAL COMPONENTS 1
900 MAIN CONTOROLLER PCB ASSY
810 FIXING ASSY
102 INTERNAL COMPONENTS 2
460 LASER SCANNER ASSY
DUPLEX
FRAME R UNIT
PAPER FEED
CASSETTE ASSEMBLY
530 INTERMEDIATE TRANS. BELT ASSY
105 INTERNAL COMPONENTS 5
Детали DUPLEX
| Деталь: | REGISTRATION ASSY |
| Парткод: | FM4-8513-000 |
| Деталь: | COVER, HOLDER |
| Парткод: | RC2-2014-000 |
| Деталь: | PAD, SEPARATION |
| Парткод: | RL1-1785-000 |
| Деталь: | PICK-UP ROLLER ASSY |
| Парткод: | RM1-4426-000 |
| Деталь: | MP PAPER PICK-UP ASSY |
| Парткод: | FM4-8514-000 |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | RM1-4840-000 |
| Деталь: | PAPER PICK-UP ASSY |
| Парткод: | FM4-8511-000 |
| Деталь: | MP CLUTCH ASSY |
| Парткод: | RM1-5428-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | LABEL, MOTOR CAUTION |
| Парткод: | FC8-8748-000 |
| Деталь: | SHEET, GUIDE, RIGHT |
| Парткод: | FC0-3944-000 |
| Деталь: | ARM, TRAY, LEFT |
| Парткод: | RC2-3386-000 |
| Деталь: | ARM, TRAY, RIGHT |
| Парткод: | RC2-3387-000 |
| Деталь: | ARM, TRAY |
| Парткод: | RC2-3388-000 |
| Деталь: | SHEET, GUIDE, LEFT |
| Парткод: | FC0-3943-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | COVER, REAR, LOWER |
| Парткод: | FC0-3881-000 |
| Деталь: | CONNECTOR, SNAP TIGHT |
| Парткод: | VS1-7584-006 |
| Деталь: | REAR DOOR ASSY |
| Парткод: | FM4-8503-000 |
| Деталь: | LINK, DOOR |
| Парткод: | RC2-3750-000 |
| Деталь: | LINK, GUIDE |
| Парткод: | RC2-3752-000 |
| Деталь: | CAP, LINK |
| Парткод: | RC2-3774-000 |
| Деталь: | FAN |
| Парткод: | RK2-2276-000 |
| Деталь: | PAPER FEED GUIDE ASSY |
| Парткод: | RM1-4838-000 |
| Деталь: | REAR DOOR RIB ASSY |
| Парткод: | RM1-4876-000 |
| Деталь: | PAPER RE-PICK UP GUIDE ASSY |
| Парткод: | RM1-4877-000 |
| Деталь: | DUPLEXING FEED GUIDE ASSY |
| Парткод: | RM1-4879-000 |
| Деталь: | REVERSE DRIVE ASSY |
| Парткод: | RM1-4880-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | LABEL, JAM CLEARING |
| Парткод: | FU7-8873-000 |
| Деталь: | LABEL, GROUNDING CAUTION |
| Парткод: | FU7-8875-000 |
| Деталь: | INTERNAL COMPONENTS 6 |
| Парткод: | NPN |
| Деталь: | DC CONTROLLER PCB ASSY |
| Парткод: | FM4-9356-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | RK2-2302-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-2146-000 |
| Деталь: | MOTOR, DC |
| Парткод: | RL1-1800-000 |
| Деталь: | MOTOR, DC |
| Парткод: | RL1-3053-000 |
| Деталь: | DRIVER PCB ASSY |
| Парткод: | FM4-9372-000 |
| Деталь: | RELAY PCB ASSY |
| Парткод: | RM1-5293-000 |
| Деталь: | INLET CABLE ASSY |
| Парткод: | RM1-5368-000 |
| Деталь: | SENSOR CABLE ASSY |
| Парткод: | RM1-5385-000 |
| Деталь: | DRAM MOTOR CABLE ASSY |
| Парткод: | RM1-5393-000 |
| Деталь: | DEVELOPING MOTOR CABLE ASSY |
| Парткод: | RM1-5394-000 |
| Деталь: | FEED MOTOR CABLE ASSY |
| Парткод: | RM1-5395-000 |
| Деталь: | SENSOR CABLE ASSY |
| Парткод: | RM1-5400-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | FM4-9357-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | FM4-9358-000 |
| Деталь: | OPTION CABLE ASSY |
| Парткод: | RM1-5434-000 |
| Деталь: | RLD CABLE ASSY |
| Парткод: | RM1-5435-000 |
| Деталь: | HOLDER, CARTRIDGE DOOR SENSOR |
| Парткод: | RC2-3220-000 |
| Деталь: | FIXING MOTOR CABLE ASSY |
| Парткод: | RM1-5438-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, MACH., FLAT HEAD, M3X4 |
| Парткод: | XA9-0679-000 |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, TP, M3X6 |
| Парткод: | XA9-1418-000 |
| Деталь: | ARM, DOOR SENSOR |
| Парткод: | RC2-3221-000 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | RM1-8042-010 |
| Деталь: | EVERYNIGHT POWER PCB ASSEMBLY |
| Парткод: | FK3-1986-000 |
| Цена: | 3 900 ₽ |
| Деталь: | AC CONNECTING PCB ASSEMBLY |
| Парткод: | FM4-9361-000 |
| Деталь: | INTERNAL COMPONENTS 4 |
| Парткод: | NPN |
| Деталь: | CASSETTE |
| Парткод: | FM4-8504-000 |
| Деталь: | Узел переноса изображения, в сборе |
| Парткод: | RM2-0192-000CN |
| Цена: | 19 300 ₽ |
| Деталь: | COVER, RIGHT FRONT |
| Парткод: | FC0-3865-000 |
| Цена: | 800 ₽ |
| Деталь: | BUTTON, POWER |
| Парткод: | FC0-3866-000 |
| Цена: | 260 ₽ |
| Деталь: | PANEL, RIGHT |
| Парткод: | FC0-3873-000 |
| Деталь: | COVER, RIGHT |
| Парткод: | FC0-3874-000 |
| Деталь: | COVER, LEFT |
| Парткод: | FC0-3879-000 |
| Деталь: | COVER, TOP, FRONT |
| Парткод: | FC0-3870-000 |
| Деталь: | COVER, TOP, REAR |
| Парткод: | FC0-3871-000 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | FM4-8505-000 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | FM4-8506-000 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | FM4-8507-000 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | FM4-8508-000 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | FM4-8509-000 |
| Деталь: | CONTROL PANEL ASSY |
| Парткод: | FM4-8510-000 |
| Деталь: | FRONT DOOR ASSY |
| Парткод: | FM4-8501-000 |
| Деталь: | BUTTON, TEST PRINT SWITCH |
| Парткод: | RC2-3719-000 |
| Деталь: | LABEL, PAPER SIZE |
| Парткод: | FC8-8742-000 |
| Деталь: | LABEL, PAPER SIZE |
| Парткод: | FC8-8745-000 |
| Деталь: | FAN |
| Парткод: | RK2-2276-000 |
| Деталь: | COVER, USB INNER |
| Парткод: | FC0-3878-000 |
| Деталь: | COVER, USB |
| Парткод: | FC0-3888-000 |
| Деталь: | COVER, DIMM ASSY |
| Парткод: | FC0-3875-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, USB BLANKING |
| Парткод: | FC0-3887-000 |
| Деталь: | COVER, SD |
| Парткод: | FC0-3897-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
| Деталь: | TEMPERATURE SENSOR UNIT |
| Парткод: | RK2-3267-000 |
| Деталь: | CARTRIDGE TRAY ASSY |
| Парткод: | RM1-4836-000 |
| Деталь: | H. V. POWER SUPPLY PCB ASSY |
| Парткод: | RM1-5294-050 |
| Деталь: | SD SLOT EXTENSION PCB ASSEMBLY |
| Парткод: | FM4-8869-000 |
| Деталь: | ENV. SENSOR CABLE ASSY |
| Парткод: | RM1-5399-000 |
| Деталь: | SENSOR CABLE ASSY |
| Парткод: | RM1-5398-000 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5935-000 |
| Деталь: | SCREW, W/WASHER, M3X8 |
| Парткод: | XA9-1420-000 |
| Цена: | 1 100 ₽ |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | RAIL, LEFT |
| Парткод: | RC2-3800-000 |
| Деталь: | RAIL, RIGHT |
| Парткод: | RC2-3801-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-2249-000 |
| Деталь: | CABLE, USB |
| Парткод: | FK3-1797-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FC0-3919-000 |
| Деталь: | GUIDE |
| Парткод: | FC0-3905-000 |
| Деталь: | MEMORY PCB ASSEMBLY |
| Парткод: | FM4-8868-000 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | IC, T6TH5EFG-0002(0), STANDARD |
| Парткод: | FK2-7852-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM0-3418-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM0-3419-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM0-3420-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM3-8292-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM4-3062-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM4-3063-000 |
| Деталь: | LABEL, CAUTION |
| Парткод: | FC8-8743-000 |
| Деталь: | ROLLER, PRESSURE |
| Парткод: | RC2-3367-000 |
| Цена: | 5 000 ₽ |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8293-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8295-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM3-8296-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | RL1-1802-000 |
| Деталь: | COLOR MISREGIST. SENSOR ASSY |
| Парткод: | RM1-4850-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | MP SOLENOID ASSY |
| Парткод: | RM1-5420-000 |
| Деталь: | HINGE, MULTI-PURPOSE COVER |
| Парткод: | RC2-3395-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-3396-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | FM4-3359-000 |
| Цена: | 32 000 ₽ |
| Деталь: | Вентилятор |
| Парткод: | RK2-2276-000CN |
| Цена: | 650 ₽ |
| Деталь: | Кассета для картриджей, в сборе |
| Парткод: | RM1-4836-000CN |
| Цена: | 3 400 ₽ |
| Деталь: | Датчик |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | Датчик |
| Парткод: | WG8-5935-000CN |
| Цена: | 900 ₽ |
| Деталь: | Плата форматтера |
| Парткод: | FM0-3419-010 |
| Деталь: | Датчик температуры, в сборе |
| Парткод: | RK2-3267-000CN |
| Цена: | 2 200 ₽ |
| Деталь: | Датчик плотности цвета, в сборе |
| Парткод: | RM1-4850-000CN |
| Цена: | 2 000 ₽ |
| Деталь: | Плата высоковольтного питания |
| Парткод: | RM1-5294-050CN |
| Цена: | 8 500 ₽ |
| Деталь: | Плата питания |
| Парткод: | RM1-7355-000CN |
| Цена: | 1 300 ₽ |
| Деталь: | Площадка отделения бумаги из лотка ручной подачи |
| Парткод: | RL1-1785-000CN |
| Цена: | 240 ₽ |
| Деталь: | Ролик захвата бумаги из лотка ручной подачи |
| Парткод: | RL1-1802-000CN |
| Цена: | 260 ₽ |
| Деталь: | Ролик отделения бумаги из кассеты, в сборе |
| Парткод: | RM1-4840-000CN |
| Цена: | 480 ₽ |
| Деталь: | COVER TOP STOPPER |
| Парткод: | RM1-5420-000CN |
| Цена: | 1 100 ₽ |
| Деталь: | Pickup Roller |
| Парткод: | RM1-8047-030CN |
| Цена: | 450 ₽ |
| Деталь: | Правая панель |
| Парткод: | FC0-3873-010 |
| Цена: | 3 300 ₽ |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | RM1-4852-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | PAPER DELIVERY ASSY |
| Парткод: | FM4-8515-000 |
| Деталь: | FIXING MOTOR UNIT |
| Парткод: | RM1-4896-000 |
| Деталь: | POWER SUPPLY SUB PCB ASSY |
| Парткод: | RM1-7355-000 |
| Деталь: | REGISTRATION MOTOR ASSY |
| Парткод: | RM1-5419-000 |
| Деталь: | SCREW, TP, M3X6 |
| Парткод: | XA9-1418-000 |
| Деталь: | FUSER CABLE ASSY |
| Парткод: | RM1-7356-000 |
| Деталь: | SCREW, MACH., FLAT HEAD, M3X4 |
| Парткод: | XA9-0679-000 |
| Деталь: | SCREW, D, M3X6 |
| Парткод: | XA9-1835-000 |
| Деталь: | COVER, REAR, UPPER |
| Парткод: | FC0-3882-000 |
| Деталь: | DIMM, SMD-E51288HG-6E, SDRAM |
| Парткод: | FK2-8341-000 |
| Деталь: | ROM PCB ASSEMBLY |
| Парткод: | FM4-8872-000 |
| Деталь: | INTERNAL COMPONENTS 5 |
| Парткод: | NPN |
Коды ошибок
E000-0000
E001-0000
E001-0001
E003-0000
E003-0001
E004-0000
E012-0000
E012-0001
E014-0000
E014-0001
E015-0001
E020-0000
E021-0003
E021-0007
E021-1003
E021-2003
E052
E066
E070
E078-0000
E078-0001
E100-0000
E100-0001
E100-0002
E100-0003
E110-0000
E110-0002
E194-0000
E196-0000
E196-0001
E196-0002
E197-0001
E198
E602-0002
E602-0003
E602-0006
E602-0008
E602-1102
E602-1112
E602-1113
E602-1302
E602-1312
E602-1313
E602-1602
E602-1612
E602-1613
E604-0000
E604-0001
E616-0001
E721-0001
E730-100A
E730-C000
E730-D001
E733-0000
E733-0001
E733-0004
E733-0006
E740-0002
E740-0004
E740-0800
E740-0900
E740-1100
E747-0000
E748-2012
E748-4000
E748-4020
E760-0000
E805-0001
E805-0003
E805-0005
E806
E808-0001
E840-0000
Описание
| Error code: | E000-0000 |
| Description: | Startup error The temperature detected by the main or sub thermistor does not rise to the specified value during startup control. |
| Causes: | The detection temperature of the main thermistor did not increase after start of the power distribution to the heater. |
| Remedy: | - Check the fixing film connector. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0000 |
| Description: | Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature 235 deg C) during temperature control |
| Causes: | The main thermistor detected a temperature of higher than 255 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E001-0001 |
| Description: | Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature (300 deg C) during temperature control. |
| Causes: | The sub thermistor detected a temperature of higher than 290 degree C. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0000 |
| Description: | Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The main thermistor detected a temperature of lower than 120 degree C for more than 1 second when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E003-0001 |
| Description: | Abnormally low temperature (detected by sub thermistor) After the temperature detected by the sub thermistor has reached the specified value, it does not reach the specified value during initial rotation. |
| Causes: | The sub thermistor detected a temperature of lower than 80 degree C for more than 2 seconds when 20 seconds elapsed after start of the power distribution to the heater. |
| Remedy: | - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. |
| Error code: | E004-0000 |
| Description: | Fixing power supply drive circuit error |
| Causes: | 43 to 57Hz could not be detected continuously for more than 5 seconds when zero cross detection started. |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the DC Controller Board. (2) Replace the Fixing Assembly. |
| Error code: | E012-0000 |
| Description: | Error in ITB motor activation. |
| Causes: | The cycle of ITB motor speed detection signal does not move in the specified cycle after ITB motor drive is started. Cause Failure in ITB motor, failure in DC controller PCB |
| Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
| Error code: | E012-0001 |
| Description: | Error in ITB motor activation. |
| Causes: | If the ITB motor speed detection signal comes off the specified cycle after it turned once to the specified cycle. Cause Failure in ITB motor, failure in DC controller PCB. |
| Remedy: | - Check the connectors of ITB motor and DC controller PCB - Replace the ITB motor - Replace the DC controller PCB |
| Error code: | E014-0000 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor startup error The target speed was not reached within a specified time after startup of the motor. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E014-0001 |
| Description: | Fixing motor failure |
| Causes: | Fixing motor rotation error The motor rotated out of the target speed during rotation after the target speed was reached. |
| Remedy: | Check the contact of the connector between the fixing motor (J516) and the DC controller PCB (J81). Check the gear between the fixing motor and the fixing assembly. Replace the fixing motor. |
| Error code: | E015-0001 |
| Description: | Cassette 1 lift up motor error |
| Causes: | Cassette 1 lift up motor error |
| Remedy: | Reconnect the connector J151 on the DC controller PCB and the relay connector J742. Check the cassette media stack surface sensor in the sensor monitor mode. If a failure is found, replace the lifter drive unit. Replace the lifter drive unit. |
| Error code: | E020-0000 |
| Description: | Density sensor failure warning |
| Error code: | E021-0003 |
| Description: | Error in developing motor |
| Causes: | Motor (Bk) rotation error |
| Error code: | E021-0007 |
| Description: | Error in developing motor |
| Causes: | Error in startup of the Motor (Bk) |
| Error code: | E021-1003 |
| Description: | Error in developing motor |
| Causes: | Developing motor does not rotate. Cause Failure in developing motor, failure in DC controller PCB. |
| Remedy: | - Check the connectors of developing motor, DC controller PCB - Replace the developing motor - Replace the DC controller PCB |
| Error code: | E021-2003 |
| Description: | Error in developing motor |
| Causes: | The cycle of developing motor speed detection signal does not move in the specified cycle after developing motor drive is started. Cause Failure in developing motor, failure in DC controller PCB |
| Remedy: | - Check the connectors of developing motor, DC controller PCB - Replace the developing motor - Replace the DC controller PCB |
| Error code: | E052 |
| Description: | NV-RAM error - Normal read/write from/to NVM (EEPROM) on the MCU PWB cannot be performed. - The MCU PWB (or X-ROM PWB) was replaced in error. |
| Causes: | • MCU PWB • X-ROM PWB |
| Remedy: | 1 Check of the MCU PWB Turn the main power off and then back on. Does the error occur again after the power is turned on? To Step 2 Problem solved 2 Check of the MCU PWB Turn the main power on and off several times. Does the error occur? To Step 3 Problem solved 3 Replacement of the EEPROM Replace the EEPROM on the MCU PWB. Does the error occur? To Step 4 Make adjustments that are indicated by adjustment icons. 4 Replacement of the MCU PWB After putting the removed EEPROM back to the place, replace the MCU PWB. Does the error occur? Put the removed MCU PWB back and then replace the X-ROM PWB. Problem solved Do not replace both the EEPROM and X-ROM PWB at one time. Doing so makes the printer unable to start up. When have replaced one of them, the stored data will be downloaded to the newly installed one from the other. (From EEPROM to X-ROM PWB, or From X-ROM PWB to EEPROM) Therefore, when replacing the EEPROM or the X-ROM PWB, be sure about the followings. • When replacing EEPROM: X-ROM PWB and MCU PWB should be those that originally come with the printer. • When replacing X-ROM PWB: EEPROM and MCU PWB should be those that originally come with the printer. Be sure to perform the followings after replacing the EEPROM. “5.1.2 Part/unit-based adjustment items” • Color Registration Adjustment • Writing correction values of the followings • Sensor Assy TP • Motor Disp (for 4 colors) |
| Error code: | E066 |
| Display: | E066 error Y motor |
| Description: | Occur:Difference between the actual paper size and realization of engine. |
| Remedy: | Remove the paper and close the cover. |
| Error code: | E070 |
| Display: | E070 error Y time-out |
| Description: | Time-out condition in head travel distance (Yaxis) during plotter operation. Displayed if carriage does not reach the defined position. |
| Causes: | Y-axis encoder has an error. |
| Remedy: | 1. Check error history from "Test: Elec." of self-diagnosis function. 2. Move carriage in both directions while the plotter is turned off, and check if there is any position where carriage does not move smoothly. 3. Set the number of endurance running cycles to 50 or more from "Life: CR motor" of selfdiagnosis function, and check if "Y motor error" occurs. - • Clean and lubricate CR rail roller guide. • Check connection of following connectors. Main board: • CR motor assembly connector: J106 • CR cable connector: J110 - J114 CR board: • CR cable connector: J201 - J205 • TF_ENC assembly connector: J210 4. Check if T fence is contaminated or worn out. • If grease or dust collect: Wipe fence with a dry cloth. • If ink deposit presents: Wipe it off with cloth dampened with neutral detergent. • If contamination or deposit is too heavy: Replace T fence. 5. Check "Y Encoder" from "Test: Encoder" of selfdiagnosis function. a) If NG: Check following cable connection. • CR board assembly connector J210 b) Replace following parts. • T fence • CR motor assembly • CR board assembly • CR cable • Replace main board assembly. 6. Main board assembly may be damaged. |
| Error code: | E078-0000 |
| Description: | Error in primary transfer disengagement. |
| Causes: | Primary transfer disengagement mechanism did not work properly. Cause Disengagement mechanism error, ITB Tension Sensor error, Pickup Motorerror, DC Controller PCB error |
| Remedy: | - Check the disengagement mechanism. - Check the connectors of the ITB Tension - - Sensor, Pickup Motor and the DC Controller PCB (J167, J202, J160, J201, J140). - Replace the ITB Tension Sensor. - Replace the Pickup Motor. - Replace the DC Controller PCB. |
| Error code: | E078-0001 |
| Description: | Primary transfer disengagement mechanism failure |
| Causes: | Primary transfer disengagement mechanism failure At the time of searching the home position: Considering that the coupling of primary transfer engagement/ disengagement drive may not be connected, the solenoid was pulled for maximum 6 times in the condition where the flag was detected once. But the HP sensor did not detect the color print engagement position. * If a flag is not detected even once, it is considered that the ITB unit is absent. At the time of changing the position The position after turning ON/OFF of the solenoid did not match the HP sensor value. |
| Remedy: | Check whether the ITB unit is installed or not. Reconnect the connector J181 on the DC controller PCB. Check the primary transfer roller disengagement switch in the sensor monitor mode. If a failure is found, replace the primary transfer roller disengagement switch assembly. Execute the primary transfer roller engagement/disengagement drive test in the actuator drive mode. If the primary transfer roller does not perform engagement/disengagement, replace the fixing drive unit. |
| Error code: | E100-0000 |
| Description: | BD detection PCB failure The BD detection PCB is faulty. |
| Causes: | Yellow optical assembly failure |
| Remedy: | - Check the connector of the BD detection PCB. - Replace the laser scanner unit. - Replace the DC controller PCB. |
| Error code: | E100-0001 |
| Description: | Error detection on any of scanner motor, laser unit, and BD detection at scanner area. |
| Causes: | Magenta optical assembly failure |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Laser Scanner Unit. (2) Replace the DC Controller Board. |
| Error code: | E100-0002 |
| Description: | Optical assembly error (Laser) |
| Causes: | Cyan optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E100-0003 |
| Description: | Optical assembly error (Laser) |
| Causes: | Black optical assembly failure |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0000 |
| Description: | Optical assembly error (Scanner motor) |
| Causes: | Optical assembly error (Scanner motor initial operation failure) |
| Remedy: | Check the contact of the connector between the laser scanner unit and the DC controller. Replace the laser scanner unit. |
| Error code: | E110-0002 |
| Description: | Error in first artificial BD adjustment |
| Causes: | Primary pseudo BD correction |
| Error code: | E194-0000 |
| Description: | Error in CPR sensor |
| Causes: | If CPR sensor is judged error. Cause Soiling in density detection sensor, failure in density detection sensor, failure in DC controller PCB, failure in toner cartridge. |
| Remedy: | - Check the connector of DC controller PCB - Replace the ITB unit - Replace the DC controller PCB - Replace the toner cartridge |
| Error code: | E196-0000 |
| Description: | Invalid RFU execution requested |
| Causes: | D-con update for the host machine or the optional cassette is not completed. |
| Error code: | E196-0001 |
| Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (mainn ROM). |
| Causes: | D-con update for the optional cassette is not completed. |
| Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
| Error code: | E196-0002 |
| Description: | Image processor PCB failure Error on writing and readout ROM of image processor PCB (option ROM). |
| Causes: | Can not access to DC controller NVRAM Cause Failure in DC controller PCB |
| Remedy: | - Putting the switch on/off of the power supply. - Replace the image processor PCB. |
| Error code: | E197-0001 |
| Description: | Engine communication error |
| Causes: | Error between DC controller PCB and main controller PCB. Cause Failure in connection between PCB, failure in DC controller PCB, failure in controller PCB. |
| Remedy: | - Check the connection of the connector of the DC controller PCB and controller PCB - Replace the DC controller PCB - Replace the controller PCB |
| Error code: | E198 |
| Description: | Breakdown in DC controller memory |
| Causes: | Breakdown in DC controller memory Cause Failure in DC controller PCB |
| Remedy: | - Replace the DC controller PCB |
| Error code: | E602-0002 |
| Description: | HDD error |
| Causes: | Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged. |
| Remedy: | Burn the Bootable CD again. |
| Error code: | E602-0003 |
| Description: | HDD error |
| Causes: | HDD access error An error occurred caused by the device or hardware when accessing to the HDD during execution of bootrom. (Damage to the sector / Busy device status, etc.) |
| Remedy: | Turn on the power again. |
| Error code: | E602-0006 |
| Description: | HDD error |
| Causes: | SubBootable load failure A SubBootable CD was not contained. A SubBootable CD was damaged. |
| Remedy: | Burn the SubBootable CD again. |
| Error code: | E602-0008 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | Alternative block of flash memory is almost depleted. |
| Remedy: | Perform the following procedure to replace the the Main Controller PCB and export/import user information. 1. Export user information from the flash memory of the old Main Controller PCB (before replacement). 2. Replace the Main Controller PCB. Import user information to the flash memory of the new Main Controller PCB (after replacement). |
| Error code: | E602-1102 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | Error detection of file system (LBP7680Cx only) |
| Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. If E616-0001 occurs at restart after turning OFF and then ON the power, execute the following procedures. 1. Initialize MEAP area, and install MEAP application again. (Refer to the remedy for E616-0001.) 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E602-1112 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | Device access error (LBP7680Cx only) |
| Remedy: | Execute the following procedures. If E616- 0001 occurs after turning OFF and then ON the power (procedure 1), install MEAP application again by following the remedy for E616-0001 first. Then, execute the procedure 2. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E602-1113 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | Device access error (LBP7680Cx only) |
| Remedy: | Execute the following procedures. If E616- 0001 occurs after turning OFF and then ON the power (procedure 1), install MEAP application again by following the remedy for E616-0001 first. Then, execute the procedure 2. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E602-1302 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | File system initialization error (LBP7680Cx only) |
| Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E602-1312 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | Device access error (LBP7680Cx only) |
| Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E602-1313 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | Device access error (LBP7680Cx only) |
| Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E602-1602 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | File system initialization error (LBP7680Cx only) |
| Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E602-1612 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | Device access error (LBP7680Cx only) |
| Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E602-1613 |
| Description: | E602-1102 to 1613 Only LBP7680Cx is supported. |
| Causes: | Device access error (LBP7680Cx only) |
| Remedy: | Execute the following procedures. 1. Turn OFF and then ON the power. 2. Download the /APL_CDS firmware again by Updater. |
| Error code: | E604-0000 |
| Description: | Memory error |
| Causes: | Lack of memory capacity |
| Remedy: | Check the memory capacity inserted to each slot. |
| Error code: | E604-0001 |
| Description: | Insufficient memory capacity |
| Causes: | Failed to allocate the memory required to start PDL. |
| Remedy: | - Remove and then install the additional memory. - Replace the additional memory with a correct one. - Turn OFF and then ON the power. - Replace the Controller PCB. |
| Error code: | E616-0001 |
| Description: | (LBP7680Cx only) |
| Causes: | MEAP application was deleted by auto recovery at restart after E602-11XX. |
| Remedy: | Initialize MEAP area in the flash memory with the following procedures, and install MEAP application again. 1. Initialize the MEAP area. Service Mode > FUNCTION GR. > MEAP > MEAP FUNCTION > ON 2. Install MEAP application again. |
| Error code: | E721-0001 |
| Description: | Printer service call |
| Causes: | Printer engine which was not supported by the controller was connected. Printer engine of a different model was connected. |
| Remedy: | Only LBP7680Cx is supported. |
| Error code: | E730-100A |
| Description: | Printer service call |
| Error code: | E730-C000 |
| Description: | An error such as memory not acquired at initialization occurred. |
| Remedy: | Turn on the power again. |
| Error code: | E730-D001 |
| Description: | Printer service call |
| Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
| Remedy: | Only LBP7680Cx is supported. |
| Error code: | E733-0000 |
| Description: | Erroneous communication between controller and printer Cannot communicate with the printer at startup. |
| Causes: | Printer communication error (communication error at initial communication and negotiation packet error) |
| Remedy: | - Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB. |
| Error code: | E733-0001 |
| Description: | Printer communication error (Invalid communication after communication is established, Parity error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-0004 |
| Description: | Printer communication error (Undefined command error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E733-0006 |
| Description: | Printer communication error (Unknown communication error) |
| Remedy: | Turn on the power again. Replace the DC controller PCB. |
| Error code: | E740-0002 |
| Description: | Error detection on either Network Board or Mac address |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Check the connection of the network cable. (2) Replace the Main Controller Board. |
| Error code: | E740-0004 |
| Description: | LAN controller chip access error |
| Remedy: | 1.Check the area around the LAN chip. 2.Replace the board. |
| Error code: | E740-0800 |
| Description: | Invalid MAC address detection |
| Causes: | Model code mismatch |
| Error code: | E740-0900 |
| Description: | Invalid MAC address detection |
| Causes: | Mismatch of the model of firmware sent when downloading |
| Error code: | E740-1100 |
| Description: | Invalid MAC address detection |
| Causes: | Detection of falsification of the Controller Board |
| Error code: | E747-0000 |
| Description: | EEPROM error |
| Causes: | EEPROM error Cause Failure in main controller PCB |
| Remedy: | - Replace the main controller PCB |
| Error code: | E748-2012 |
| Description: | Failed to rewrite due to no more alternative block of Flash ROM (NAND) available. |
| Error code: | E748-4000 |
| Description: | Timeout of G-Chip loop back |
| Remedy: | Replace the main controller PCB. |
| Error code: | E748-4020 |
| Description: | Unknown device detected on the PCI |
| Remedy: | Replace the main controller PCB. |
| Error code: | E760-0000 |
| Description: | CPU exception occurred. |
| Remedy: | Turn on the power again. |
| Error code: | E805-0001 |
| Description: | Error in duplex cooling fan |
| Causes: | Fan 1 failure |
| Error code: | E805-0003 |
| Description: | Fan failure |
| Causes: | Controller fan failure detected The controller fan does not rotate because some kind of failure occurred in it. |
| Remedy: | Replace the controller fan. |
| Error code: | E805-0005 |
| Description: | Error in duplex cooling fan |
| Causes: | Duplex cooling fan can not rotate the specified number of rotations. Cause Failure in duplex cooling fan, failure in DC controller PCB |
| Remedy: | - Check the connectors of duplex cooling fan and DC controller PCB - Replace the duplex cooling fan |
| Error code: | E806 |
| Description: | Error in power supply cooling fan |
| Causes: | Power cooling fan can not rotate the specified number of rotations. Cause Failure in power supply cooling fan, failure in DC controller PCB |
| Remedy: | - Check the connectors of power supply cooling fan and DC controller PCB - Replace the power cooling fan |
| Error code: | E808-0001 |
| Description: | Fixing Assembly_Edge Left Cooling Fan error |
| Remedy: | When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. (1) Replace the Edge Left Cooling Fan. (2) Replace the DC Controller Board. |
| Error code: | E840-0000 |
| Description: | Pressure release mechanism failure |
| Causes: | The target pressure position was not reached even when 3.5 seconds (approximately 1.5 rotation of the cam) elapsed after start of the fixing motor reverse rotation. |
| Remedy: | Check the gears and detection flags related to fixing pressure release mechanism. Replace the fixing pressure release sensor (PS9). Replace the fixing motor. Replace the fixing assembly. |
