Canon LaserSHOT LBP3018
Рейтинг
Модули
102 INTERNAL COMPONENTS 2
101 INTERNAL COMPONENTS 1
103 INTERNAL COMPONENTS 3
100 EXTERNAL COVERS, PANELS, ETC.
Детали 103 INTERNAL COMPONENTS 3
| Деталь: | FIXING PAPER DELIVERY ASSY |
| Парткод: | FM3-7122-000 |
| Деталь: | FIXING PAPER DELIVERY ASSY |
| Парткод: | FM3-5662-000 |
| Деталь: | FIXING PAPER DELIVERY ASSY |
| Парткод: | FM3-6973-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | FM3-7121-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | RM1-4009-000 |
| Деталь: | FIXING FILM ASSEMBLY |
| Парткод: | RM1-4010-000 |
| Деталь: | ROLLER, PRESSURE |
| Парткод: | RC2-1183-000 |
| Цена: | 5 100 ₽ |
| Деталь: | SPRING, TENSION |
| Парткод: | RU5-2943-000 |
| Деталь: | INTERNAL COMPONENTS 2 |
| Парткод: | NPN |
| Деталь: | PANEL, REAR |
| Парткод: | FL2-9294-000 |
| Деталь: | CONTACT, CABLE |
| Парткод: | RU5-2953-000 |
| Деталь: | SC R EW,W/WAS HER,M3X6 |
| Парткод: | XB2-7300-605 |
| Деталь: | SCREW, P, M4X10 |
| Парткод: | XB4-5401-005 |
| Деталь: | ENGINE CONTROL PCB ASSY |
| Парткод: | FM3-5409-000 |
| Деталь: | ENGINE CONTROL PCB ASSY |
| Парткод: | FM3-5410-000 |
| Деталь: | PICK-UP TRANSFER FRAME ASSY |
| Парткод: | FM3-5661-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU5-2942-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU5-2941-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-1067-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-1066-000 |
| Деталь: | ROLLER, PAPER PICK-UP |
| Парткод: | RL1-1443-000 |
| Деталь: | ROLLER, TRANSFER |
| Парткод: | RM1-4023-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM3-5737-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM3-5738-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM3-5734-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM3-5735-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM3-5736-000 |
| Деталь: | SEPARATION PAD ASSY |
| Парткод: | RM1-4006-000 |
| Деталь: | INTERNAL COMPONENTS 1 |
| Парткод: | NPN |
| Деталь: | MOTOR, DC24V |
| Парткод: | RL1-1450-000 |
| Деталь: | FFC, LASER |
| Парткод: | RK2-1697-000 |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | RM1-4030-000 |
| Деталь: | MOTOR PCB ASSY |
| Парткод: | FM3-6144-000 |
| Деталь: | INTERNAL COMPONENTS 3 |
| Парткод: | NPN |
| Деталь: | FRONT COVER ASSY |
| Парткод: | FM3-5665-000 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | FM3-5653-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-6975-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-5666-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-6977-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-6976-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-7123-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-6974-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-6978-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-7120-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-6979-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-7124-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-7119-000 |
| Деталь: | PAPER PICK-UP TRAY ASSY |
| Парткод: | FM3-5654-000 |
| Деталь: | PAPER DELIVERY TRAY ASSY |
| Парткод: | FC8-3063-000 |
| Деталь: | PAPER DELIVERY TRAY ASSY |
| Парткод: | FC8-3045-000 |
| Деталь: | LABEL, DOCUMENT PROHIBITION |
| Парткод: | FU6-8599-000 |
| Деталь: | LABEL, DOCUMENT PROHIBITION |
| Парткод: | FU6-8597-000 |
| Деталь: | LEFT COVER ASSY |
| Парткод: | FM3-5667-000 |
| Деталь: | LEFT COVER ASSY |
| Парткод: | FM3-5655-000 |
| Деталь: | RIGHT COVER ASSY |
| Парткод: | FC8-3053-000 |
| Деталь: | RIGHT COVER ASSY |
| Парткод: | FC8-3020-000 |
| Деталь: | STOPPER, POST CARD |
| Парткод: | FC8-3030-000 |
| Деталь: | DOOR, CARTRIDGE |
| Парткод: | FC8-3055-000 |
| Деталь: | DOOR, CARTRIDGE |
| Парткод: | FC8-3023-000 |
| Деталь: | STOPPER, PAPER |
| Парткод: | FC8-3028-000 |
| Деталь: | TOP COVER ASSEMBLY |
| Парткод: | FM3-5663-000 |
| Деталь: | TOP COVER ASSEMBLY |
| Парткод: | FM3-5650-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1670-000 |
| Деталь: | EMBLEM, LASER SHOT |
| Парткод: | RC2-3004-000 |
| Деталь: | EMBLEM, LASER SHOT |
| Парткод: | RC1-6217-000 |
| Деталь: | PLATE, NAME |
| Парткод: | FC5-4822-000 |
| Деталь: | STOPPER, PAPER, A |
| Парткод: | FC8-3064-000 |
| Деталь: | STOPPER, PAPER, A |
| Парткод: | FC8-3029-000 |
| Деталь: | TRAY, SINGLE SHEET FEED |
| Парткод: | FM3-6972-000 |
| Деталь: | TRAY, SINGLE SHEET FEED |
| Парткод: | FM3-5660-000 |
| Деталь: | COVER, REAR |
| Парткод: | FC8-3056-000 |
| Деталь: | COVER, REAR |
| Парткод: | FC8-3024-000 |
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FC8-3067-000 |
| Деталь: | TRAY, PAPER DELIVERY |
| Парткод: | FC8-3050-000 |
| Деталь: | LABEL, JAM CLEARING |
| Парткод: | FU6-8598-000 |
| Деталь: | LABEL, JAM CLEARING |
| Парткод: | FU6-8595-000 |
| Деталь: | EXTERNAL COVERS, PANELS, ETC. |
| Парткод: | NPN |
Коды ошибок
E000
E001
E003
E004
E100
E196
E733
E747
Описание
| Error code: | E000 |
| Display: | E000 |
| Description: | Fuser Temperature Rising Error |
| Causes: | The temperature of Fuser does not rise up to 50C. |
| Remedy: | Error clearance 1 Have you cleared the fuser error in the Error Clear Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Error Clear Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Lamp (H1) 3 Unplug the machine, and then check the resistance of Lamp (H1) with the multimeter. Is it 15 ohm or lower? No Replace the Lamp. Thermistors (TH1 & TH2) 4 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. Confirm that the machine is turned on, and then check the voltage of the orange line (J220-4). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. DC Power Supply (DCP1) or Fuse 5 Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Relay (RY1) 6 Select the Device Operation Mode, and then change the signal of the following signal to “H”. Signal Code : 22 (Fuser Relay) And check the resistance between the following points. Between RY1-2 and RY1-4 Between RY1-6 and RY1-8 Is the each resistance almost 0 ohm? No Replace the Relay. Solid State Relay (SSR1) 7 Select the Device Operation Mode, and then change the signal of the following signals to “H”. Signal Code : 22 (Fuser Relay) 21 (Fuser Lamp 1) Then check the voltage between J105-1 and J105-2. Is it 0V? Refer to the page 8-16 as for the Device Operation Mode.) CAUTION Change the signal of “21” (Fuser Lamp 1) to “L” after checking! No Replace the PW10520 PWB. Yes Replace the Solid State Relay |
| Error code: | E001 |
| Display: | E001 error DRAM |
| Description: | Standard DRAM error: Abnormal condition in standard memory mounted on main board assembly |
| Causes: | The temperature of fuser rises over 230C |
| Remedy: | Main board assembly may be defective. Replace main board assembly. |
| Error code: | E003 |
| Display: | Unable to Update 0003 Check the firmware update file and try again. |
| Description: | Fuser Temperature Abnormal Fall Error |
| Causes: | The difference of temperature between center and side of fuser becomes 50C or more. |
| Remedy: | Error clearance 1 Have you cleared the fuser error in the Error Clear Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Error Clear Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Thermistors (TH1 & TH2) 3 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. |
| Error code: | E004 |
| Display: | Unable to Update 0004 Check the firmware update file and try again. |
| Description: | Fuser Temperature Abnormal Fall Error |
| Causes: | The Lamp of fuser lights (Signal HEAT1 is “H”) to heat up the Fuser Roller in the ready condition, but even 1C of temperature rise can not be accomplished within 15 seconds. |
| Remedy: | Error clearance 1 Have you cleared the fuser error in the Error Clear Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Error Clear Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Lamp (H1) 3 Unplug the machine, and then check the resistance of Lamp (H1) with the multimeter. Is it 15 ohm or lower? No Replace the Lamp. Thermistors (TH1 & TH2) 4 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. Confirm that the machine is turned on, and then check the voltage of the orange line (J220-4). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. DC Power Supply (DCP1) or Fuse 5 Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Relay (RY1) 6 Select the Device Operation Mode, and then change the signal of the following signal to “H”. Signal Code : 22 (Fuser Relay) And check the resistance between the following points. Between RY1-2 and RY1-4 Between RY1-6 and RY1-8 Is the each resistance almost 0 ohm? No Replace the Relay. Solid State Relay (SSR1) 7 Select the Device Operation Mode, and then change the signal of the following signals to “H”. Signal Code : 22 (Fuser Relay) 21 (Fuser Lamp 1) Then check the voltage between J105-1 and J105-2. Is it 0V? Refer to the page 8-16 as for the Device Operation Mode.) CAUTION Change the signal of “21” (Fuser Lamp 1) to “L” after checking! No Replace the PW10520 PWB. Yes Replace the Solid State Relay |
| Error code: | E100 |
| Display: | E100 error Vacuum pump |
| Description: | Abnormal condition in vacuum pump. |
| Causes: | • PH Unit • PH Interface Board (PWB-D) • Mechanical Control Board (PWB-M) |
| Remedy: | (1) MAIN board assembly may be damaged. * Replace MAIN board assembly. |
| Error code: | E196 |
| Display: | E196 |
| Description: | DC controller memory failure |
| Causes: | DC controller PCB ROM update failed. |
| Remedy: | 1) Defective DC controller PCB Action: Replace it. |
| Error code: | E733 |
| Description: | Original not reaching large original exit sensor (exit section) |
| Causes: | An error in data communication occurs in the Engine controller. |
| Remedy: | Are the read roller and reverse roller stained? ↓ YES Clean the rollers. NO Is the reverse flapper working properly? ↓ YES NO Adjust the reverse solenoid. |
| Error code: | E747 |
| Display: | E747 |
| Description: | Optical Fan Motor error. When the lock signal is detected continuously for the predetermined time during fan rotation. |
| Causes: | • Fuser Fan Motor (M7) • PH Fan Motor (M8) • Suction Fan Motor (M13) • Ozone Fan Motor (M9) • PS Fan Motor (M6) • PU Fan Motor (M12) |
| Remedy: | 1 Check the motor connector connection status, and correct if it is improper. 2 Check the load status of the fan section, and correct if it is improper. 3 Check the operation of M8. p115 PWB-A CNF2-A-1(REM) 5-G 4 Replace the PWB-A. |
