Canon MF8240Cw
Рейтинг
Модули
READER ASSEMBLY
LASER SCANNER ASSEMBLY
READER/ ADF ASSEMBLY (ADF MODEL)
FIXING ASSY
READER/COPYBOARD ASSEMBLY (COPYBOARD MODEL)
CASSETTE
INTERNAL COMPONENTS 1
INTERNAL COMPONENTS 5
MAIN CONTROLLER PCB ASSEMBLY
EXTERNAL COVERS, PANELS, ETC.
PAPER FEEDER ASSEMBLY (ADF MODEL)
INTERMEDIATE TRANS. BELT ASSY
INTERNAL COMPONENTS 4
INTERNAL COMPONENTS 2
INTERNAL COMPONENTS 3
Детали PAPER FEEDER ASSEMBLY (ADF MODEL)
| Деталь: | BELT, TIMING |
| Парткод: | FC9-1650-000 |
| Деталь: | MOUNT, SUPPORTER |
| Парткод: | FC9-2101-000 |
| Деталь: | SPACER, CIS |
| Парткод: | FC9-7573-000 |
| Деталь: | SPACER, CIS |
| Парткод: | FC9-7571-000 |
| Деталь: | SPACER, CIS |
| Парткод: | FC9-7574-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-1884-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-3942-000 |
| Деталь: | READER COVER UNIT |
| Парткод: | FM0-3591-000 |
| Деталь: | READER COVER UNIT |
| Парткод: | FM0-4848-000 |
| Деталь: | CABLE, READER |
| Парткод: | FM4-3653-000 |
| Деталь: | DC MOTOR ASSEMBLY |
| Парткод: | FM4-4301-000 |
| Деталь: | CONTACT IMAGE SENSOR ASSY |
| Парткод: | FM4-9076-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-003 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7177-004 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | CORE |
| Парткод: | FK2-5242-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | FM0-3589-000 |
| Деталь: | READER ASSEMBLY |
| Парткод: | FM0-4847-000 |
| Деталь: | LASER SCANNER ASSEMBLY |
| Парткод: | FM0-4590-000 |
| Деталь: | ROLLER, PICK-UP |
| Парткод: | FC7-6189-000 |
| Цена: | 550 ₽ |
| Деталь: | BUSHING |
| Парткод: | FC7-6320-000 |
| Деталь: | FLAG, DOCUMENT SCANNER |
| Парткод: | FC7-6321-000 |
| Деталь: | ELIMINATOR, STATIC CHARGE |
| Парткод: | FC7-6322-000 |
| Деталь: | PLATE, GROUNDING |
| Парткод: | FC9-1503-000 |
| Деталь: | COVER, REAR |
| Парткод: | FL3-9296-000 |
| Деталь: | COVER, FRONT UPPER |
| Парткод: | FL3-9295-000 |
| Деталь: | TRAY, DOCUMENT |
| Парткод: | FC9-1534-000 |
| Деталь: | TRAY, SUB DOCUMENT |
| Парткод: | FC9-1535-000 |
| Деталь: | PANEL, OPEN/CLOSE |
| Парткод: | FL0-1992-000 |
| Деталь: | SHEET, WHITE |
| Парткод: | FC0-4435-000 |
| Деталь: | COVER, BASE |
| Парткод: | FE2-2353-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FE2-3484-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FE2-3486-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FE2-3485-000 |
| Деталь: | TRAY, SUB |
| Парткод: | FC9-5655-000 |
| Деталь: | GUIDE, DOCUMENT, FRONT |
| Парткод: | FC9-5656-000 |
| Деталь: | GUIDE, DOCUMENT, REAR |
| Парткод: | FC9-5657-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FC9-7562-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FC9-7564-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FC9-7563-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FC9-7566-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FC9-7568-000 |
| Деталь: | LABEL, GLASS CLEANING |
| Парткод: | FC9-7567-000 |
| Деталь: | ROLLER, SEPARATION |
| Парткод: | FL2-6637-000 |
| Цена: | 650 ₽ |
| Деталь: | HINGE, ADF |
| Парткод: | FL3-2453-000 |
| Деталь: | HOLDER, DOCUMENT,RELEASE SHEET |
| Парткод: | FL3-3539-000 |
| Деталь: | PAPER FEED GUIDE ASSEMBLY |
| Парткод: | FM0-4855-000 |
| Деталь: | SEPARATION ROLLER ASSEMBLY |
| Парткод: | FM3-9538-000 |
| Цена: | 3 700 ₽ |
| Деталь: | SCREW, M3X10 |
| Парткод: | XA9-0831-000 |
| Деталь: | GEAR, 24T |
| Парткод: | FU7-0672-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2018-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FU7-8406-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FU7-8407-000 |
| Деталь: | GEAR, 18T |
| Парткод: | FU8-0895-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2007-000 |
| Деталь: | RETAINING RING |
| Парткод: | HC1-0586-000 |
| Деталь: | BUSHING |
| Парткод: | HU1-1022-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FE2-2443-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FE2-2445-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FE2-2444-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM0-4787-000 |
| Деталь: | FIXING ASSY (220-240V) |
| Парткод: | FM0-4788-000 |
| Деталь: | LABEL, SIZE INDEX |
| Парткод: | FE2-2445-000 |
| Деталь: | COVER, BASE |
| Парткод: | FE2-2353-000 |
| Деталь: | PLATE, PAPER SIZE |
| Парткод: | FE2-3486-000 |
| Деталь: | COPYBOARD COVER ASSEMBLY |
| Парткод: | FM0-4846-000 |
| Деталь: | LABEL, COPY PROHIBITION |
| Парткод: | FU7-8406-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | CASSETTE |
| Парткод: | FM4-4263-000 |
| Деталь: | COVER, SPRING, LEFT |
| Парткод: | FC7-9868-000 |
| Деталь: | COVER, SPRING, RIGHT |
| Парткод: | FC7-9869-000 |
| Деталь: | PRIORITY SLOT TRAY ASSY |
| Парткод: | FM3-3441-000 |
| Деталь: | RAIL, CASSETTE, RIGHT FRONT |
| Парткод: | RL1-1849-000 |
| Деталь: | HOLDER, MF TRAY, RIGHT |
| Парткод: | RC2-2006-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | RU6-2016-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2042-000 |
| Деталь: | RAIL, CASSETTE, LEFT FRONT |
| Парткод: | RC2-1878-000 |
| Деталь: | RAIL, CASSETTE, LEFT REAR |
| Парткод: | RC2-1879-020 |
| Деталь: | LABEL, LASER CAUTION |
| Парткод: | RU6-8007-000 |
| Деталь: | PRIORITY SLOT DRIVE ASSY |
| Парткод: | FM0-3542-000 |
| Деталь: | ARM, MF TRAY, LEFT |
| Парткод: | RC2-1993-000 |
| Деталь: | ARM, MF TRAY, RIGHT |
| Парткод: | RC2-1997-000 |
| Деталь: | HOLDER, MF TRAY, LEFT |
| Парткод: | RC2-2007-000 |
| Деталь: | RAIL, CASSETTE, RIGHT REAR |
| Парткод: | RL1-1850-000 |
| Деталь: | PLATE, USB GROUNDING |
| Парткод: | FC9-4507-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-3518-000 |
| Деталь: | DC CONTROLLER PCB ASSY |
| Парткод: | FM0-3913-000 |
| Деталь: | USB PCB ASSEMBLY |
| Парткод: | FM0-4655-000 |
| Деталь: | SPEAKER |
| Парткод: | FK3-3944-000 |
| Деталь: | CABLE, FIXING AC |
| Парткод: | FM0-3903-000 |
| Деталь: | CORE, FERRITE |
| Парткод: | FK2-8767-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | RK2-3125-000 |
| Деталь: | FIXING POWER SUPPLY ASSEMBLY |
| Парткод: | FM0-4741-000 |
| Деталь: | FIXING POWER SUPPLY ASSEMBLY |
| Парткод: | FM0-4742-000 |
| Деталь: | GUIDE, CABLE, E |
| Парткод: | FE2-1444-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SCREW, W/WASHER D, M3X8 |
| Парткод: | XA9-1831-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FK3-1951-000 |
| Деталь: | WIRELESS LAN PCB ASSEMBLY |
| Парткод: | FM4-9831-000 |
| Деталь: | DRIVER PCB ASSY |
| Парткод: | RM1-8706-000 |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | RK2-4540-000 |
| Деталь: | POWER SUPPLY SWITCH ASSY |
| Парткод: | FM0-4789-000 |
| Деталь: | POWER SUPPLY SWITCH ASSY, L6 |
| Парткод: | FM0-4790-000 |
| Деталь: | IC, T6TH5EFG-0002(0), STANDARD |
| Парткод: | FK2-7852-000 |
| Деталь: | IC, ASIC, MB8AA4241EPBH-GE1 |
| Парткод: | FK3-1800-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM0-4670-000 |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM0-4667-000 |
| Цена: | 44 900 ₽ |
| Деталь: | MAIN CONTROLLER PCB ASSEMBLY |
| Парткод: | FM0-4666-000 |
| Деталь: | CAM, FRONT COVER, LEFT |
| Парткод: | FC7-9827-000 |
| Деталь: | COVER, LEFT |
| Парткод: | FC9-4440-000 |
| Деталь: | COVER, RIGHT |
| Парткод: | FE2-3593-000 |
| Деталь: | COVER, RIGHT ,L6 |
| Парткод: | FE2-2381-000 |
| Деталь: | GUIDE, SIDE, RIGHT |
| Парткод: | FE2-2321-000 |
| Деталь: | GUIDE, HANDLE |
| Парткод: | FC9-4443-000 |
| Деталь: | SHEET, BLANKING |
| Парткод: | FE2-3429-000 |
| Деталь: | COVER, UPPER REAR |
| Парткод: | FE2-2385-000 |
| Деталь: | COVER, LOWER REAR |
| Парткод: | FE2-2386-000 |
| Деталь: | GUIDE, REAR |
| Парткод: | FE2-2387-000 |
| Деталь: | COVER, PAPER PICK-UP SLOT |
| Парткод: | FC9-4454-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM0-4990-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM0-4991-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM0-4997-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM0-5000-000 |
| Деталь: | CONTROL PANEL ASSEMBLY |
| Парткод: | FM0-4989-000 |
| Деталь: | HINGE ASSEMBLY |
| Парткод: | FM4-1493-000 |
| Деталь: | SHEET,BLANKING |
| Парткод: | HB1-5537-000 |
| Деталь: | COVER, TOP |
| Парткод: | FM0-3545-000 |
| Деталь: | COVER UNIT, FRONT |
| Парткод: | FM0-3544-000 |
| Деталь: | SCREW,TP M3X8 |
| Парткод: | XA9-0476-000 |
| Деталь: | SHAFT, SUPPORT |
| Парткод: | RC2-2015-000 |
| Деталь: | LABEL, HIGH TMP. CAUTION |
| Парткод: | FU7-8090-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, MODULAR |
| Парткод: | FC9-4584-000 |
| Деталь: | RATCHET, PAPER FEED ROLLER |
| Парткод: | FC7-6052-010 |
| Деталь: | PAD, SEPARATION |
| Парткод: | FC7-6297-000 |
| Цена: | 230 ₽ |
| Деталь: | HOLDER, SEPARATION PAD |
| Парткод: | FC7-6299-000 |
| Деталь: | CLAMP, SEPARATION PAD |
| Парткод: | FC7-6300-000 |
| Деталь: | LEVER, RELEASE |
| Парткод: | FC9-1512-000 |
| Деталь: | PLATE, ROLLER GROUNDING |
| Парткод: | FC9-1523-000 |
| Деталь: | GUIDE, PAPER DELIVERY |
| Парткод: | FC9-1526-000 |
| Деталь: | SHEET, SEPARATION PAD |
| Парткод: | FC9-5654-000 |
| Деталь: | ARM, SEPARATION SWING |
| Парткод: | FL3-1431-000 |
| Деталь: | GUIDE LOWER ASSEMBLY |
| Парткод: | FL3-1437-000 |
| Деталь: | PAPER FEED ROLLER ASSEMBLY |
| Парткод: | FM4-1885-000 |
| Деталь: | PAPER DELIVERY ROLLER ASSY |
| Парткод: | FL3-2458-000 |
| Деталь: | DRIVE PLATE ASSEMBLY |
| Парткод: | FM4-1880-000 |
| Деталь: | MOTOR DRIVE ASSY |
| Парткод: | FM0-4858-000 |
| Деталь: | ROLLER, AUXILIARY |
| Парткод: | FU5-6992-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU6-2998-000 |
| Деталь: | SPRING, TENSION |
| Парткод: | FU6-2999-000 |
| Деталь: | GEAR, 20T |
| Парткод: | FU7-0667-000 |
| Деталь: | GEAR, 54T |
| Парткод: | FU7-0668-000 |
| Деталь: | GEAR, 46T/23T |
| Парткод: | FU7-0669-000 |
| Деталь: | GEAR, 36T |
| Парткод: | FU7-0671-000 |
| Деталь: | GEAR, 21T/42T |
| Парткод: | FU7-0676-000 |
| Деталь: | GEAR, 51T/17T |
| Парткод: | FU7-0678-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU7-2016-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2008-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | FU8-2010-000 |
| Деталь: | RETAINING RING |
| Парткод: | HC1-0586-000 |
| Деталь: | BUSHING |
| Парткод: | HU1-1022-000 |
| Деталь: | CONNECTOR, SNAP TIGHT, BK |
| Парткод: | VS1-7207-004 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000 |
| Деталь: | GUIDE ASSEMBLY, UPPER |
| Парткод: | FM4-1882-000 |
| Деталь: | PAPER FEEDER ASSEMBLY |
| Парткод: | FM0-4856-000 |
| Деталь: | INTERMEDIATE TRANS. BELT ASSY |
| Парткод: | RM1-8777-000 |
| Цена: | 20 500 ₽ |
| Деталь: | CARTRIDGE TRAY ASSY |
| Парткод: | RM1-8774-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | COVER, DOOR SIDE, LEFT |
| Парткод: | FC9-4455-000 |
| Деталь: | COVER, DOOR SIDE, RIGHT |
| Парткод: | FE2-2388-000 |
| Деталь: | FIXING DRIVE ASSY |
| Парткод: | RM1-8784-000 |
| Цена: | 4 700 ₽ |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2064-000 |
| Деталь: | LEVER, RAIL, LEFT |
| Парткод: | RC2-1871-000 |
| Деталь: | CLAW, FRONT DOOR, LEFT |
| Парткод: | RC2-2871-000 |
| Деталь: | LEVER, ESTRANGEMENT |
| Парткод: | RC2-1911-000 |
| Деталь: | STOPPER, LEVER |
| Парткод: | RC2-1914-000 |
| Деталь: | CLAMP, CARTRIDGE TRAY, LEFT |
| Парткод: | RC2-3108-000 |
| Деталь: | CLAMP, CARTRIDGE TRAY, RIGHT |
| Парткод: | RC2-3109-000 |
| Деталь: | OFFHOOK PCB ASSEMBLY |
| Парткод: | FM4-8968-000 |
| Деталь: | FAX-NCU PCB ASSEMBLY |
| Парткод: | FM0-4658-000 |
| Деталь: | FAX-NCU PCB ASSEMBLY |
| Парткод: | FM0-4657-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | FM0-4739-000 |
| Деталь: | POWER SUPPLY ASSY |
| Парткод: | FM0-4740-000 |
| Деталь: | GUIDE, CABLE, A |
| Парткод: | RC2-1819-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-1922-000 |
| Деталь: | SPRING, TORSION |
| Парткод: | RC2-3071-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | FM0-3543-000 |
| Деталь: | SUB DRIVE ASSY |
| Парткод: | RM1-8785-000 |
| Деталь: | IC, PHOTO INTERRUPTER |
| Парткод: | WG8-5935-000 |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0104-000 |
| Деталь: | CABLE, FLAT |
| Парткод: | FL3-8566-000 |
| Деталь: | FAN |
| Парткод: | RK2-4255-000 |
| Деталь: | CORD, POWER |
| Парткод: | FK2-9583-000 |
| Деталь: | CORD, POWER, 230V |
| Парткод: | FH2-7080-000 |
| Деталь: | COVER, HOLDER |
| Парткод: | RC2-2014-000 |
| Деталь: | GUIDE, CABLE, F |
| Парткод: | FE2-1445-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-2111-000 |
| Деталь: | BUSHING |
| Парткод: | RC2-2112-000 |
| Деталь: | SCREW, D, M3X8 |
| Парткод: | XA9-1671-000 |
| Цена: | 170 ₽ |
| Деталь: | SEPARATION ROLLER ASSY |
| Парткод: | RM1-8765-000 |
| Деталь: | PICK-UP ROLLER ASSY |
| Парткод: | RM1-8047-030 |
| Деталь: | FLAG, DOOR SENSOR, REAR |
| Парткод: | RC2-2879-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RC2-2880-000 |
| Деталь: | COVER, DOOR SENSOR |
| Парткод: | RC2-2881-000 |
| Деталь: | SUPPORT, HIGH VOLTAGE PCB |
| Парткод: | RC2-2899-000 |
| Деталь: | LEVER, CARTRIDGE TRAY PUSH |
| Парткод: | RC2-2902-000 |
| Деталь: | HOLDER, CARTRIDGE TRAY PUSH |
| Парткод: | RC2-2904-000 |
| Деталь: | LEVER, CARTRIDGE TRAY PUSH |
| Парткод: | RC2-2906-000 |
| Деталь: | GUIDE, I.T.B., R |
| Парткод: | RC2-2907-000 |
| Деталь: | SPRING, GROUNDING |
| Парткод: | RC2-3100-000 |
| Деталь: | HOLDER, CONTACT SPRING |
| Парткод: | RL1-1844-000 |
| Деталь: | HOLDER, CONTACT SPRING |
| Парткод: | RL1-1845-000 |
| Деталь: | HOLDER, CONTACT SPRING |
| Парткод: | RL1-1846-000 |
| Деталь: | SCREW, D, M3X12 |
| Парткод: | XA9-1830-000 |
| Деталь: | PAPER FEED GUIDE ASSY |
| Парткод: | RM1-8779-000 |
| Деталь: | I.T.B. LOCK LEVER ASSY, LEFT |
| Парткод: | RM1-4482-000 |
| Деталь: | I.T.B. LOCK LEVER ASSY, RIGHT |
| Парткод: | RM1-4483-000 |
| Деталь: | H.V. POWER SUPPLY PCB ASSY |
| Парткод: | FM0-4744-000 |
| Деталь: | ROLLER, TRANSFER |
| Парткод: | RM1-4445-000 |
| Деталь: | SPRING, COMPRESSION |
| Парткод: | RU6-2017-000 |
| Деталь: | PAPER PICK-UP DRIVE ASSY |
| Парткод: | FM0-3541-000 |
| Деталь: | SCREW, W/WASHER D, M3X8 |
| Парткод: | XA9-1831-000 |
Коды ошибок
E000 0000
E001 0000
E001 0001
E003 0000
E003 0001
E004 0000
E012 0000
E012 0001
E014 0000
E014 0001
E015 0001
E020 0000
E021 1003
E021 2003
E024 0000
E024 0001
E024 0002
E024 0003
E052 0000
E066 0000
E070 0000
E078 0000
E100 0000
E100 0001
E100 0002
E100 0003
E110 0000
E194 0000
E196 0000
E196 1000
E196 2000
E198 0000
E202 0001
E202 0002
E246 0000
E247 0000
E248 0001
E350 0000
E351 0000
E354 0000
E355 0000
E355 0004
E355 0005
E719 0000
E733 0000
E736 0000
E736 0001
E744 0001
E744 0002
E744 1001
E744 4000
E744 5000
E744 6000
E744 7000
E746 0000
E766 8000
E766 9000
E766 xxxx1
E804 0004
E805 0000
E805 0005
E806 0000
E808 0000
E840 0000
Описание
| Error code: | E000 0000 |
| Description: | Error in temperature rising of Fixing Assembly |
| Causes: | Temperature of the Fixing Assembly did not reach a certain temperature within the specified period of time. |
| Remedy: | 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB. |
| Error code: | E001 0000 |
| Description: | Abnormal high temperature of Fixing Assembly |
| Causes: | It was detected that the temperature of the Fixing Assembly was abnormally high. |
| Remedy: | 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB. |
| Error code: | E001 0001 |
| Description: | Abnormal high temperature in fixing (The sub thermistor detected a temperature of higher than 290 degree C. |
| Causes: | Abnormally high temperature detected by sub thermistor (sub thermistor triggered) |
| Remedy: | 1) Reconnect the connector on the Engine Controller PCB. 2) Turn OFF the power supply switch, and remove the Fixing Assembly. Measure the resistance value between the connector (FSRTH) at the Fixing Assembly side and grounding. If the resistance value is 1k ohm or lower, replace the Fixing Assembly. 3) Replace the Engine Controller PCB. |
| Error code: | E003 0000 |
| Description: | Abnormal low temperature of Fixing Assembly |
| Causes: | It was detected that the temperature of the Fixing Assembly was abnormally low. |
| Remedy: | 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB. |
| Error code: | E003 0001 |
| Description: | Abnormal low temperature in fixing (The sub thermistor detected a temperature of lower than 80 degree C for more than 2 seconds when 20 seconds elapsed after start of the power distribution to the heater.) |
| Causes: | Temperature drop detected by sub thermistor after attaining the target temperature (sub thermistor triggered) |
| Remedy: | 1) Reconnect the connector on the Engine Controller PCB. 2) Turn OFF the power supply switch, and remove the Fixing Assembly. Measure the resistance value between the connector (FSRTH) at the Fixing Assembly side and grounding. If the resistance value is not between 368k ohm and 512k ohm (normal temperature), replace the Fixing Assembly. 3) If there is no induction between the connector (ACN) at the Fixing Assembly side and the connector (ACH) while the assembly is removed, replace the assembly. 4) Replace the Engine Controller PCB. |
| Error code: | E004 0000 |
| Description: | Error in fixing power supply drive circuit |
| Causes: | Failed to detect the zero cross signal for the specified period of time or more. |
| Remedy: | 1. Check the connection of connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB. |
| Error code: | E012 0000 |
| Description: | Black drum motor error (Failure in drum motor initial operation) The target speed was not reached within a specified time after startup of the motor. |
| Causes: | Error in attaining the target ITB motor rotation detected based on ITB motor speed detection signal after ITB motor is actuated. |
| Remedy: | 1) Reconnect the connector on the Main Motor 2) Replace the Engine Controller PCB. |
| Error code: | E012 0001 |
| Description: | Black drum motor error (Failure in drum motor rotation) The motor rotated out of the target speed during rotation after the target speed was reached. |
| Causes: | Error in ITB motor rotation after attaining the target rotation detected based on ITB motor speed detection signal |
| Remedy: | 1) Reconnect the connector on the Main Motor 2) Replace the Engine Controller PCB. |
| Error code: | E014 0000 |
| Description: | Error in startup of the Main Motor |
| Causes: | Revolution of the Main Motor did not reach the specified value. |
| Remedy: | 1. Check the connection of connector between the Main Motor and the Engine Controller PCB. 2. Replace the Main Motor. 3. Replace the Engine Controller PCB. |
| Error code: | E014 0001 |
| Description: | Fixing Motor rotation error |
| Causes: | Error in fixing motor rotation after attaining the target rotation detected based on fixing motor speed detection signal. |
| Remedy: | 1) Reconnect the connector on the Fixing Motor 2) Replace the Fixing Motor |
| Error code: | E015 0001 |
| Description: | Error in developing roller contact |
| Causes: | Failed to detect changes in developing home position sensor signals within the pre-defined time after actuating main motor to control the developing roller contact. |
| Remedy: | 1.Check connectors of developing home position sensor, main motor and DC controller PCB. 2.Replace developing home position sensors 3.Replace main motors 4.Replace DC controller PCBs |
| Error code: | E020 0000 |
| Description: | Error in density sensor |
| Causes: | Failed to receive sufficient light to detect image density |
| Remedy: | 1.Check DC controller PCB onnectors. 2.Replace ITB units 3.Replace DC controller PCBs 4.Replace toner cartridges |
| Error code: | E021 1003 |
| Description: | Error in developing motor |
| Causes: | Cause of developing motor rotation error: problem in developing motor / DC controller PCB |
| Remedy: | 1.Check connectors of developing motor and DC controller PCB. 2.Replace developing motor 3.Replace DC controller PCB |
| Error code: | E021 2003 |
| Description: | Error in developing motor |
| Causes: | Error in attaining the target developing motor rotation detected based on developing motor speed detection signal after developing motor is actuated. |
| Remedy: | 1.Check connectors of developing motor and DC controller PCB. 2.Replace developing motor 3.Replace DC controller PCBs |
| Error code: | E024 0000 |
| Description: | Error in toner level sensor |
| Causes: | Abnormal output of toner level sensor (Yellow) |
| Remedy: | 1.Replace toner cartridges 2.Replace high-voltage power supply PCBs 3.Replace DC controller PCBs |
| Error code: | E024 0001 |
| Description: | Error in toner level sensor |
| Causes: | Abnormal output of toner level sensor (Magenta) |
| Remedy: | 1.Replace toner cartridges 2.Replace high-voltage power supply PCBs 3.Replace DC controller PCBs |
| Error code: | E024 0002 |
| Description: | Error in toner level sensor |
| Causes: | Abnormal output of toner level sensor (Cyan) |
| Remedy: | 1.Replace toner cartridges 2.Replace high-voltage power supply PCBs 3.Replace DC controller PCBs |
| Error code: | E024 0003 |
| Description: | Error in toner level sensor |
| Causes: | Abnormal output of toner level sensor (Black) |
| Remedy: | 1.Replace toner cartridges 2.Replace high-voltage power supply PCBs 3.Replace DC controller PCBs |
| Error code: | E052 0000 |
| Description: | Error in 2-sided unit detection |
| Causes: | Failed to detect 2-sided unit |
| Remedy: | 1.Check connectors of 2-sided unit and DC controller PCB 2.Replace DC controller PCBs |
| Error code: | E066 0000 |
| Description: | Environment sensor failure |
| Causes: | Error in environment sensor |
| Remedy: | Replace the environment sensor. |
| Error code: | E070 0000 |
| Description: | Error in ITB / TOP sensor |
| Causes: | Error in ITB / TOP sensor |
| Remedy: | 1.Check connectors of ITB unit and DC controller PCB. 2.Replace ITB units 3.Replace DC controller PCBs |
| Error code: | E078 0000 |
| Description: | Error in primary transfer roller contact |
| Causes: | Primary transfer roller contact mechanism does not normally function |
| Remedy: | 1.Check contact mechanism 2.Check connectors of ITB tension sensor, pickup motor and DC controller PCB. 3.Replace ITB tension sensors 4.Replace pickup motors / DC controller PCBs |
| Error code: | E100 0000 |
| Description: | Laser Scanner Assembly error |
| Causes: | At the Laser Scanner Unit, BD cycle was not within the specified range. |
| Remedy: | 1. Check the connection of connector between the Main Controller PCB and the Laser Scanner Unit. 2. Check the connection of connector between the Relay PCB and the Laser Scanner Unit. 3. Replace the Laser Scanner Unit. |
| Error code: | E100 0001 |
| Description: | Error in scanner motor/laser unit/BD |
| Causes: | Failure in Magenta optical unit |
| Remedy: | 1.Check connectors of laser scanner unit and DC controller PCB 2.Replace laser scanner units 3.Replace DC controller PCBs |
| Error code: | E100 0002 |
| Description: | Error in scanner motor/laser unit/BD |
| Causes: | Failure in Cyan optical unit |
| Remedy: | 1.Check connectors of laser scanner unit and DC controller PCB 2.Replace laser scanner units 3.Replace DC controller PCBs |
| Error code: | E100 0003 |
| Description: | Error in scanner motor/laser unit/BD |
| Causes: | Failure in Black optical unit |
| Remedy: | 1.Check connectors of laser scanner unit and DC controller PCB 2.Replace laser scanner units 3.Replace DC controller PCBs |
| Error code: | E110 0000 |
| Description: | Optical assembly error (Scanner motor initial operation failure) |
| Causes: | Scanner failed to be ready after starting up pseudo-BD control |
| Remedy: | 1) Reconnect the connector on the Laser Scanner Unit. 2) Replace the Laser Scanner Unit. |
| Error code: | E194 0000 |
| Description: | Error in Patch Sensor |
| Causes: | Patch Sensor does not function normally |
| Remedy: | 1.Check DC controller PCB connectors 2.Replace ITB units 3.Replace DC controller PCBs 4.Replace toner cartridges |
| Error code: | E196 0000 |
| Description: | DCON error |
| Causes: | Failed to update ROM of DC controller PCB |
| Remedy: | 1) Replace the Engine Controller PCB. |
| Error code: | E196 1000 |
| Description: | Main Controller PCB reading/writing error |
| Causes: | Error in reading/writing of main program in the Main Controller PCB |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E196 2000 |
| Description: | Main Controller PCB reading/writing error |
| Causes: | Error in reading/writing of setting values storage area in the Main Controller PCB |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E198 0000 |
| Description: | Failure in DC controller memory |
| Causes: | Failure in DC controller memory |
| Remedy: | Replace DC controller PCBs |
| Error code: | E202 0001 |
| Description: | CIS Unit HP error (outward) |
| Causes: | CIS Unit did not move to HP even it moved backward. Reader HP Sensor error, Reader Motor error, CIS Unit error |
| Remedy: | 1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit. |
| Error code: | E202 0002 |
| Description: | CIS Unit HP error (homeward) |
| Causes: | CIS Unit did not move to HP even it moved forward. Reader HP Sensor error, Reader Motor error, CIS Unit error |
| Remedy: | 1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit. |
| Error code: | E246 0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E247 0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E248 0001 |
| Description: | Error in access to backup data for Reader (reading error at power-on) |
| Causes: | The Reader-related adjustment values could not be read. |
| Remedy: | 1. Clear the backup RAM of RCON. Execute COPIER>FUNCTION>CLEAR>RCON. 2. Enter all the values written on the service label in service mode again. 3. Turn OFF and then ON the main power. 4. Replace the Main Controller PCB. |
| Error code: | E350 0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E351 0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E354 0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E355 0000 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E355 0004 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E355 0005 |
| Description: | System error |
| Causes: | System error |
| Remedy: | Contact to the sales companies. |
| Error code: | E719 0000 |
| Description: | Card Reader communication error (serial communication) |
| Causes: | Communication with the Card Reader could not be started at startup. |
| Remedy: | 1. Check the connection of the Card Reader-F1, and turn OFF and then ON the main power switch. 2. Remove the Card Reader-F1. NOTE: After performing the remedy work above, go through the following to clear the error: COPIER> FUNCTION> CLEAR> E719-CLR. |
| Error code: | E733 0000 |
| Description: | Printer communication error |
| Causes: | Communication error between the Engine Controller PCB and the Main Controller PCB occurred. |
| Remedy: | 1. Check the connection of connector between the Engine Controller PCB and the Main Controller PCB. 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. 4. Replace the Engine Controller PCB. |
| Error code: | E736 0000 |
| Description: | Communication error with CCU/modem |
| Causes: | Communication error with CCU/modem. NCU PCB type error. |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the NCU PCB. 3. Replace the Main Controller PCB. |
| Error code: | E736 0001 |
| Description: | Error in ROM for backing up fax data |
| Causes: | An error occurred in ROM for backing up fax data |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E744 0001 |
| Description: | Language file version error |
| Causes: | Language file version was not matched with the main program. |
| Remedy: | Install the set of the controller firmware. |
| Error code: | E744 0002 |
| Description: | Language file size error |
| Causes: | The size of the language file exceeded the upper limit. |
| Remedy: | Install the set of the controller firmware. |
| Error code: | E744 1001 |
| Description: | Firmware version error |
| Causes: | Version of the main program and the version of the start-up program was not matched. |
| Remedy: | Install the set of the controller firmware. |
| Error code: | E744 4000 |
| Description: | Engine ID error |
| Causes: | Invalid engine connection was detected. |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Check the Engine Controller PCB. 3. Install the Engine Controller PCB. 4. Install the set of the controller firmware. 5. Check the model code. (When the model code and the engine code are mismatched, E744-4000 occurs.) |
| Error code: | E744 5000 |
| Description: | Error in the Control Panel PCB |
| Causes: | Error in the Control Panel PCB (microcomputer). |
| Remedy: | 1. Check the Control Panel PCB, and install the firmware (PANEL). 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. |
| Error code: | E744 6000 |
| Description: | Communication error with the Wireless LAN PCB |
| Causes: | Unable to communicate with the Wireless LAN. |
| Remedy: | 1. Turn OFF and then ON the main power. 2. Check the connection of the Wireless LAN. 3. Install the set of the controller firmware. 4. Replace the Main Controller PCB. |
| Error code: | E744 7000 |
| Description: | Main Controller PCB error |
| Causes: | An error in the microcomputer which retains fax job information of the Main Controller PCB. |
| Remedy: | 1. Install the firmware of BKUP. 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. |
| Error code: | E746 0000 |
| Description: | Main Controller PCB error |
| Causes: | Main Controller communication error occurred (other than scan). |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB. |
| Error code: | E766 8000 |
| Description: | Digital registration error |
| Causes: | Information at digital registration could not be obtained. |
| Remedy: | 1. Install the Engine Controller firmware. 2. Install the set of the controller firmware. 3. Replace the Engine Controller PCB. |
| Error code: | E766 9000 |
| Description: | Scanner power state error |
| Causes: | An error was detected in power state of the Laser Scanner Unit. |
| Remedy: | 1. Install the set of the controller firmware. 2. Replace the Laser Scanner Unit. |
| Error code: | E766 xxxx1 |
| Description: | Error in firmware |
| Causes: | Error in connection occurred due to main controller software: xxxx Task number related to Exception is shown in decimal |
| Remedy: | 1.Power off/on 2.Update firmware |
| Error code: | E804 0004 |
| Description: | Controller Fan error |
| Causes: | Since the startup of the Controller Fan, the Fan was locked for a specified consecutive period of time. |
| Remedy: | 1. Check power supply to the Controller Fan. 2. Replace the Controller Fan. |
| Error code: | E805 0000 |
| Description: | Main Fan error |
| Causes: | The Main Fan was locked for a specified consecutive period of time. |
| Remedy: | 1. Check the connection of the Main Fan. 2. Replace the Main Fan. |
| Error code: | E805 0005 |
| Description: | Error in 2-sided cooling fan |
| Causes: | 2-sided cooling fan does not rotate in the specified rotation speed. |
| Remedy: | 1.Check connectors of 2-sided cooling fan / DC controller PCB 2.Replace 2-sided cooling fans 3.Replace DC controller PCBs |
| Error code: | E806 0000 |
| Description: | Error in fixing / fixing power supply cooling fan |
| Causes: | Fixing / fixing power supply cooling fan does not rotate in the specified rotation speed. |
| Remedy: | 1.Check connectors of fixing/fixing power supply cooling fan and DC controller PCB 2.Replace fixing / fixing power supply cooling fans 3.Replace DC controller PCBs |
| Error code: | E808 0000 |
| Description: | Failure detection of Low Voltage Power Supply PCB |
| Causes: | Printer detected failure of the Low Voltage Power Supply PCB. |
| Remedy: | Replace the Engine Controller PCB. |
| Error code: | E840 0000 |
| Description: | Error in pressure release mechanism |
| Causes: | Failed to control in home position (under pressure) after starting home position control |
| Remedy: | 1.Replace fixing drive units 2.Replace fixing pressure release cams |
