Brother FAX-2920

Рейтинг

Парткаталог
Коды ошибок

Модули

(Детали корпуса)

(Электронные компоненты)

COVERS & LABELS

PAPER CASSETTE

DRIVE

PANEL

FRAME UNIT

Детали None

Деталь:	Fax PCA (M477
Парткод:	LG6382001
Цена:	750 ₽

Деталь:	Телефонная трубка (цвет: серый)
Парткод:	LF1518016
Цена:	1 500 ₽

$brother\LF6496002.jpg$

Деталь:	Лоток выхода бумаги из узла автоматической подачи
Парткод:	LF6496002
Цена:	1 300 ₽

Деталь:	Fax PCA (M477
Парткод:	LG6382001
Цена:	750 ₽

Деталь:	Телефонная трубка (цвет: серый)
Парткод:	LF1518016
Цена:	1 500 ₽

$brother\LF6496002.jpg$

Деталь:	Лоток выхода бумаги из узла автоматической подачи
Парткод:	LF6496002
Цена:	1 300 ₽

Деталь:	Винт
Парткод:	087320616

$brother\LM4143001.jpg$

Деталь:	Площадка отделения бумаги из кассеты
Парткод:	LM4143001

Деталь:	Узел захвата бумаги в узле сканирования, в сборе
Парткод:	LF6439002
Цена:	8 100 ₽

Деталь:	Ролик отделения бумаги в узле сканирования
Парткод:	UF5511001
Цена:	700 ₽

$brother\LM4238001.jpg$

Деталь:	Соленоид
Парткод:	LM4238001

Деталь:	Соленоид
Парткод:	LM4234001

Деталь:	Прижимной вал
Парткод:	LM4013001
Цена:	2 700 ₽

Деталь:	Шестерня привода тефлонового вала
Парткод:	LM4010001
Цена:	250 ₽

Деталь:	Термистор
Парткод:	LM4865001
Цена:	1 100 ₽

Деталь:	Лампа нагрева тефлонового вала
Парткод:	LM4022001
Цена:	1 100 ₽

Деталь:	Палец отделения бумаги от тефлонового вала
Парткод:	LM4994001
Цена:	470 ₽

$brother\LM6735001.jpg$

Деталь:	Подшипник тефлонового вала
Парткод:	LM6735001
Цена:	440 ₽

Деталь:	Подшипник тефлонового вала
Парткод:	LM6736001
Цена:	550 ₽

Деталь:	PANEL UNIT, MFC9840CDW
Парткод:	LM6724001
Цена:	15 600 ₽

$brother\LM4009001.jpg$

Деталь:	Тефлоновый вал
Парткод:	LM4009001
Цена:	1 600 ₽

Деталь:	Блок лазера
Парткод:	LM4578001
Цена:	15 800 ₽

$brother\LM4341001.jpg$

Деталь:	Главный мотор
Парткод:	LM4341001
Цена:	2 800 ₽

$brother\LG6059001.jpg$

Деталь:	Дисплей
Парткод:	LG6059001

Деталь:	Плата датчика наличия тонера
Парткод:	LJ9740001

Деталь:	Датчик крышки доступа к картриджам
Парткод:	LG5845001

Деталь:	Датчик сброса тонер-картриджа
Парткод:	LG5832001

Деталь:	Термистор
Парткод:	LG5834001

Деталь:	Плата датчика наличия тонера
Парткод:	LJ9747001

$brother\LM4225001.jpg$

Деталь:	Шестерня главного редуктора
Парткод:	LM4225001
Цена:	200 ₽

Деталь:	Чистящий ролик
Парткод:	LJ7432001
Цена:	20 ₽

Деталь:	Комплект из 4-х пластиковых роликов и пружин для узла выхода бумаги
Парткод:	LM6598001
Цена:	1 400 ₽

$brother\LM4105001.jpg$

Деталь:	Вал выхода бумаги из узла термозакрепления
Парткод:	LM4105001
Цена:	600 ₽

$brother\LM4227001.jpg$

Деталь:	Муфта шестерни главного редуктора
Парткод:	LM4227001
Цена:	190 ₽

Деталь:	Флажок датчика сброса тонер-картриджа
Парткод:	LM4260001

Деталь:	Пружина флажка датчика сброса тонер-картриджа
Парткод:	LM4261001

Деталь:	Пружина
Парткод:	LM6480001

Деталь:	Пружина соленоида
Парткод:	LM4633001

Деталь:	Вентилятор
Парткод:	LF6856001

Деталь:	Держатель светодиода датчика наличия тонера
Парткод:	LM4267001

Error code:	56
Display:	Toner Empty
Description:	The toner cartridge has run out. The machine stops printing.
Causes:	Harness connection failure of back cover switch ASSY. Eject actuator failure. Eject sensor PCB ASSY failure. Main PCB failure
Remedy:	Replace the toner cartridge with a new one.

Error code:	5B
Display:	Unable to print 5B
Description:	New toner detection lever malfunction
Causes:	New toner detection switch harness connection failure. New toner detection switch failure. Main PCB failure
Remedy:	1 New toner detection switch harness connection failure Check the harness connection of the new toner detection switch. Then, reconnect it. 2 New toner detection switch failure Replace the new toner harness ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Error code:	6A
Description:	Fuser unit failure (The side thermistor does not detect 60°C within the specified time.)
Causes:	Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure.
Remedy:	1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY.

Error code:	6B
Description:	Fuser unit failure (The center thermistor does not detect 100°C within the specified time.)
Causes:	Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure.
Remedy:	1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY.

Error code:	6C
Display:	Unable to Print 6C
Description:	Fuser unit failure (The center thermistor detects higher temperature than the specified value.)
Causes:	Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure.
Remedy:	1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY.

Error code:	6F
Display:	Unable to Print 6F
Description:	Fuser unit failure (The center and side thermistors detect extremely high temperature.)
Causes:	Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure.
Remedy:	1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY.

Error code:	71
Display:	Paper Jam 0
Description:	Paper Jam 0
Causes:	The front part of paper is jammed between pickup unit and Feed sensor.

Error code:	72
Display:	Paper Jam 1
Description:	Engine Firmware Failure The Engine Control Board detected a firmware error.
Causes:	• Engine Control Board, Pl9.1.16 • EEPROM Board, PL9.1.12
Remedy:	1 Cycle printer power. Does the error persist? Go to Step 2. Complete 2 Is P/J144 on the EEPROM Board properly seated and defect free? Go to Step 3. Reseat P/J144 or replace the EEPROM Board. 3 Turn printer power off and then back on. Does the error persist? Replace the Engine Control Board. Complete

Error code:	73
Display:	Paper Jam 2
Description:	Paper Jam 2
Causes:	The front part of paper is jammed just after passing through the discharge sensor.

Error code:	74
Display:	[TRAY x] [PAPER SIZE] EMPTY
Description:	F/W Overrun detect
Causes:	· Loose cable connection · Defective cleaner clutch · Defective IOD2 board · Defective IOD1 board · Defective MCTL board
Remedy:	1) Check the harness connected between the Engine controller and the TA board. (If the harness is out, insert it to the connector.) 2) Check the harness connected between the TA board and the Pickup unit. (If the harness is out, insert it to the connector.) 3) Check the harness connected between the Pickup unit and the cassette sensing board. (If the harness is out, insert it to the connector.) 4) Check the pickup unit. (If it is inferior part or warped part, replace it.) 5) Check the damage of the cassette sensing B . (If it is damaged, replace the cassette sensing board.) 6) In the Engine diagnostic mode, operate the running count of the paper if it is under 39. (If it is over 39, replace the Pickup unit.) 7) Replace the TA board.

Error code:	75
Display:	[TRAY x] NOT INSTALLED
Description:	VIC Limutter
Causes:	· Loose cable connection · Defective fusing unit clutch · Defective IOD2 board · Defective MCTL board
Remedy:	1) Check for any warping or damage to the cassette (In the case of warping or damage, replace the cassette)

Error code:	76
Display:	Out Bin Full
Description:	Fuser Firmware Failure A failure was detected in the Fuser Firmware.
Causes:	• Fuser, PL5.1.1 • FSR/ADC Harness, PL5.2.28 • Engine Control Board, PL9.1.16
Remedy:	1 Check the Fuser for damage. Is the Fuser damaged? Replace the Fuser. Go to Step 2. 2 Check the Fuser connection for damage. Any broken or bent pins? Repair or replace the parts. Go to Step 3. 3 Replace the Fuser. Does the error persist? Go to Step 4. Complete 4 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J361. 2. Check continuity between J36 <=> J361. Replace the Engine Control Board. Replace the FSR/ ADC Harness.

Error code:	77
Display:	WAIT IMAGE
Description:	Image Density Failure The engine detected a low-density image condition.
Causes:	• Transfer Roller, PL5.1.4 • CTD (ADC) Sensor PL5.2.19 • Engine Control Board PL9.1.16 • FSR/ADC Harness PL5.2.28
Remedy:	1 Clean the CTD (ADC) Sensor. Does the error persist? Go to Step 2. Complete 2 Check the following for evidence of fault or damage: Transfer Roller Assembly, PL5.1.4 CTD (ADC) Sensor, PL5.2.19 Replace any damaged parts. Go to Step 3. 3 Check the CTD (ADC) Sensor connector. Is P/J136 connected to the harness? Go to Step 4. Reseat the connector to the sensor. 4 Replace the CTD (ADC) Sensor. Does the error persist? Go to Step 5. Complete 5 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136 2. Check continuity between J36 <=> J136 Replace the Engine Control Board Replace the FSR/ ADC Harness.

Error code:	78
Display:	WRONG PAPER SIZE [PAPER] IN [TRAY x]
Description:	Waste Cartridge Full Detection Sensor Failure, Code 78
Causes:	• Waste Cartridge • Waste Cartridge Full Sensor • Engine Control Board
Remedy:	1 1. Remove the waste cartridge sensor holder without disconnecting the harnesses. 2. Measure the voltage between the yellow wire on the waste cartridge full sensor and frame ground, alternately interrupting the sensor. 3. Does the voltage toggle between +5 and 0 VDC? Go to step 5. Go to step 2. 2 1. Measure the voltage between the gray wire and frame ground. 2. Does the voltage measure +5 VDC? Go to step 4. Go to step 3. 3 1. Remove the rear cover and rear shield. 2. Measure the voltage at J407B-17 on the engine control board. 3. Does the voltage measure +5 VDC? Inspect the wiring harness for damage and replace, if necessary. Replace the engine control board. 4 1. Measure the voltage between the violet wire and frame ground. 2. Does the voltage measure 0 VDC? Replace the waste cartridge full sensor. Inspect the wiring harness for damage and replace, if necessary. 5 1. Remove the rear cover and rear shield. 2. Measure the voltage at J407B-16 on the engine control board. 3. Alternately interrupt the sensor 4. Does the voltage toggle between +5 and 0 VDC? Replace the engine control board. Inspect the wiring harness for damage and replace, if necessary.

Error code:	7A
Display:	Unable to clean 7A
Description:	No detection of the main motor lock signal.
Causes:	Main motor failure. Main PCB failure.
Remedy:	1 Main motor failure Replace the main motor ASSY. 2 Main PCB failure Replace the main PCB ASSY.

Error code:	7B
Display:	Unable to clean 7B
Description:	Main PCB failure
Causes:	Main PCB failure
Remedy:	1 Main PCB failure Replace the main PCB ASSY.

Error code:	80
Display:	ERROR 80 FORMAT
Description:	Engine Logic Board Failure, Code 80
Remedy:	1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete Replace the engine control board or the image processor board.

Brother FAX-2920

Модули

Детали None

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку