Epson AcuLaser C1000
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A4
Скорость печати
A4
20
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Макс. формат |
A4 |
Тип устройства |
Принтер |
Цветность печати |
цветная |
Копир |
|
Печать фотографий |
|
Сканер |
|
Принтер |
|
Двусторонняя печать |
|
Прямая печать |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
| По Y | 600 |
| По X | 600 |
| По X | 2 400 |
Скорость ч/б печати |
|
| A4 | 20 |
Макс, разрешение для цветной печати |
|
| По Y | 2 400 |
Расходные материалы |
|
Ресурс цветного картриджа/тонера |
6 000 |
Ресурс ч/б картриджа/тонера |
6 000 |
Печать на: |
|
| Этикетках |
|
| Фотобумаге |
|
| Пленках |
|
Лотки |
|
Подача бумаги |
|
| Стандартная | 500 |
Вывод бумаги |
|
| Стандартный | 100 |
Интерфейсы |
|
LPT |
|
USB |
|
Ethernet (RJ-45) |
|
Инфракрасный порт |
|
Память/Процессор |
|
Макс, объем памяти |
256 |
Объем памяти |
16 |
Дополнительная информация |
|
Мин. системные требования |
Intel Pentium II |
Поддержка ОС |
|
| Windows |
|
| Mac OS |
|
| Linux |
|
| DOS |
|
Уровень шума |
|
| При работе | 55 |
Габариты |
|
Глубина |
559 |
Высота |
511 |
Ширина |
463 |
Вес |
28 |
Модули
Main Unit 5
Main Unit 7
Main Unit 11
Main Unit 10
Main Unit 13
Main Unit 8
Main Unit 3
Main Unit 2
Main Unit 1
Main Unit 6
Main Unit 12
Main Unit 9
Main Unit 4
Детали Main Unit 13
| Деталь: | DUCT ASSY |
| Парткод: | 1058109 |
| Деталь: | LEVER |
| Парткод: | 1058111 |
| Деталь: | LEVER |
| Парткод: | 1058112 |
| Деталь: | SCREW |
| Парткод: | 1047417 |
| Деталь: | DUCT |
| Парткод: | 1058113 |
| Деталь: | FUN MOTOR |
| Парткод: | 2036357 |
| Деталь: | LEVER ASSY |
| Парткод: | 2036568 |
| Деталь: | MOTOR |
| Парткод: | 2036358 |
| Деталь: | PWB ASSY |
| Парткод: | 2036359 |
| Деталь: | STOPPER |
| Парткод: | 1046713 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036345 |
| Деталь: | LEVER |
| Парткод: | 1058117 |
| Деталь: | HOLDER |
| Парткод: | 1058118 |
| Деталь: | TENSION SPRING |
| Парткод: | 1058120 |
| Деталь: | LEVER ASSY |
| Парткод: | 1058121 |
| Деталь: | LEVER |
| Парткод: | 1058123 |
| Деталь: | LEVER |
| Парткод: | 1058124 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1058126 |
| Деталь: | DRIVING ASSY |
| Парткод: | 1058177 |
| Деталь: | TENSION SPRING |
| Парткод: | 1058178 |
| Деталь: | MOTOR ASSY |
| Парткод: | 2036363 |
| Деталь: | DRIVING ASSY |
| Парткод: | 1058180 |
| Деталь: | MOTOR ASSY |
| Парткод: | 2036364 |
| Деталь: | MOTOR ASSY |
| Парткод: | 2036365 |
| Деталь: | CLUTCH ASSY |
| Парткод: | 1058185 |
| Деталь: | GEAR |
| Парткод: | 1058187 |
| Деталь: | BUSHING |
| Парткод: | 1058188 |
| Деталь: | HOLDER |
| Парткод: | 1058190 |
| Деталь: | ROLLER |
| Парткод: | 1058288 |
| Деталь: | ROLL |
| Парткод: | 1058289 |
| Деталь: | GEAR |
| Парткод: | 1058291 |
| Деталь: | HANDLE |
| Парткод: | 1058292 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036389 |
| Деталь: | ROLLER |
| Парткод: | 1058293 |
| Деталь: | GUIDE ASSY |
| Парткод: | 2036390 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058294 |
| Деталь: | BUSHING |
| Парткод: | 1058295 |
| Деталь: | CLUTCH ASSY |
| Парткод: | 1058296 |
| Деталь: | DUCT |
| Парткод: | 1058297 |
| Деталь: | FUN MOTOR |
| Парткод: | 2036346 |
| Деталь: | BUSHING |
| Парткод: | 1058298 |
| Деталь: | STOPPER |
| Парткод: | 1047329 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036345 |
| Деталь: | ROLLER |
| Парткод: | 1058299 |
| Деталь: | LEVER |
| Парткод: | 1058300 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058301 |
| Деталь: | HOLDER ASSY |
| Парткод: | 1058302 |
| Деталь: | SCREW |
| Парткод: | 1058054 |
| Деталь: | SEAL |
| Парткод: | 1058303 |
| Деталь: | FILTER |
| Парткод: | 1058304 |
| Деталь: | GUIDE |
| Парткод: | 1058305 |
| Деталь: | GUIDE |
| Парткод: | 1058306 |
| Деталь: | GEAR |
| Парткод: | 1058307 |
| Деталь: | STOPPER |
| Парткод: | 1058308 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036392 |
| Деталь: | GUIDE |
| Парткод: | 1058309 |
| Деталь: | CALKING ASSY |
| Парткод: | 1058310 |
| Деталь: | GUIDE ASSY |
| Парткод: | 1058311 |
| Деталь: | SECOND TRANSFER ROLL |
| Парткод: | 2035703 |
| Деталь: | FUN MOTOR |
| Парткод: | 2036346 |
| Деталь: | STOPPER |
| Парткод: | 1047329 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036345 |
| Деталь: | SENSOR ASSY |
| Парткод: | 2036387 |
| Деталь: | SOLENOID |
| Парткод: | 2056354 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058278 |
| Деталь: | DRUM |
| Парткод: | 1058279 |
| Деталь: | CALKING ASSY |
| Парткод: | 1058280 |
| Деталь: | GEAR |
| Парткод: | 1058281 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058282 |
| Деталь: | ROLLER |
| Парткод: | 1058283 |
| Деталь: | LEVER |
| Парткод: | 1058284 |
| Деталь: | SHAFT ASSY |
| Парткод: | 1058285 |
| Деталь: | HOLDER |
| Парткод: | 1058286 |
| Деталь: | REGULATING PLATE ASSY |
| Парткод: | 1058337 |
| Деталь: | REGULATING PLATE ASSY |
| Парткод: | 1061694 |
| Деталь: | REGULATING PLATE ASSY |
| Парткод: | 1058339 |
| Деталь: | PLATE SPRING |
| Парткод: | 1058340 |
| Деталь: | REGULATING PLATE |
| Парткод: | 1058341 |
| Деталь: | LABEL |
| Парткод: | 1058431 |
| Деталь: | PLATE SPRING |
| Парткод: | 1058342 |
| Деталь: | LEVER |
| Парткод: | 1058343 |
| Деталь: | CASSETTE ASSY |
| Парткод: | 1061322 |
| Деталь: | PROTECTION |
| Парткод: | 1058200 |
| Деталь: | SPACER |
| Парткод: | 1058202 |
| Деталь: | COVER |
| Парткод: | 1058203 |
| Деталь: | GUIDE |
| Парткод: | 1058204 |
| Деталь: | HOLDER ASSY |
| Парткод: | 1058205 |
| Деталь: | SHIELD PLATE |
| Парткод: | 1058206 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 1058207 |
| Деталь: | LEVER |
| Парткод: | 1058208 |
| Деталь: | SWITCH |
| Парткод: | 2036366 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 1058212 |
| Деталь: | LEVER |
| Парткод: | 1058213 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058214 |
| Деталь: | CAP |
| Парткод: | 1058215 |
| Деталь: | BRACKET |
| Парткод: | 1058216 |
| Деталь: | STOPPER |
| Парткод: | 1058218 |
| Деталь: | SCREW |
| Парткод: | 1058219 |
| Деталь: | REAR COVER |
| Парткод: | 1058220 |
| Деталь: | RUBBER FOOT |
| Парткод: | 1046693 |
| Деталь: | SEAL |
| Парткод: | 1058224 |
| Деталь: | STOPPER |
| Парткод: | 1058225 |
| Деталь: | TENSION SPRING |
| Парткод: | 1058227 |
| Деталь: | LEVER |
| Парткод: | 1058228 |
| Деталь: | GUIDE |
| Парткод: | 1058229 |
| Деталь: | PRINT HEAD ASSY |
| Парткод: | 2036367 |
| Деталь: | TENSION SPRING |
| Парткод: | 1058231 |
| Деталь: | DUCT |
| Парткод: | 1058232 |
| Деталь: | MICRO SWITCH |
| Парткод: | 2036368 |
| Деталь: | LEVER |
| Парткод: | 1058234 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058236 |
| Деталь: | HINGE |
| Парткод: | 1058237 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036369 |
| Деталь: | PIN |
| Парткод: | 1058238 |
| Деталь: | LEVER |
| Парткод: | 1058241 |
| Деталь: | BUSHING |
| Парткод: | 1058243 |
| Деталь: | LEVER |
| Парткод: | 1058244 |
| Деталь: | LEVER |
| Парткод: | 1058245 |
| Деталь: | HINGE |
| Парткод: | 1058246 |
| Деталь: | PLATE NUT |
| Парткод: | 1058255 |
| Деталь: | TENSION SPRING |
| Парткод: | 1058256 |
| Деталь: | MICRO SWITCH |
| Парткод: | 2030612 |
| Деталь: | CALKING ASSY |
| Парткод: | 1058257 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058258 |
| Деталь: | SCREW |
| Парткод: | 1058054 |
| Деталь: | LEVER |
| Парткод: | 1058259 |
| Деталь: | HOLDER |
| Парткод: | 1058260 |
| Деталь: | STOPPER |
| Парткод: | 1058261 |
| Деталь: | PRINT HEAD FILTER |
| Парткод: | 1056730 |
| Деталь: | FUSING UNIT DRIVE ASSY |
| Парткод: | 1058053 |
| Деталь: | SCREW |
| Парткод: | 1058054 |
| Деталь: | GEAR |
| Парткод: | 1058055 |
| Деталь: | DUCT |
| Парткод: | 1058056 |
| Деталь: | DUCT |
| Парткод: | 1058057 |
| Деталь: | FUN MOTOR |
| Парткод: | 2036346 |
| Деталь: | ALIENATION MOTOR ASSY |
| Парткод: | 2036347 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036345 |
| Деталь: | STOPPER |
| Парткод: | 1047329 |
| Деталь: | STOP PLATE ASSY |
| Парткод: | 2036348 |
| Деталь: | CIVER |
| Парткод: | 1058059 |
| Деталь: | PROTECTION |
| Парткод: | 1058060 |
| Деталь: | COLLAR |
| Парткод: | 1058061 |
| Деталь: | RATCHET |
| Парткод: | 1058062 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058064 |
| Деталь: | REGULATING PLATE |
| Парткод: | 1058065 |
| Деталь: | GEAR |
| Парткод: | 1058066 |
| Деталь: | GEAR |
| Парткод: | 1058067 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058068 |
| Деталь: | PAWL |
| Парткод: | 1058069 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058072 |
| Деталь: | SHUTTER |
| Парткод: | 1058073 |
| Деталь: | FUSING UNIT DRIVE 3 ASSY |
| Парткод: | 1058075 |
| Деталь: | FUSER UNIT 220V |
| Парткод: | 2035702 |
| Деталь: | FUSER OIL ROLL |
| Парткод: | 1056731 |
| Деталь: | COVER ASSY |
| Парткод: | 1090712 |
| Деталь: | BUSHING |
| Парткод: | 1057985 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1057987 |
| Деталь: | BUSHING |
| Парткод: | 1057993 |
| Деталь: | LEVER |
| Парткод: | 1057994 |
| Деталь: | ROLLER ASSY |
| Парткод: | 1057996 |
| Деталь: | COLLAR |
| Парткод: | 1057997 |
| Деталь: | GEAR |
| Парткод: | 1057999 |
| Деталь: | GEAR |
| Парткод: | 1058000 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1058001 |
| Деталь: | GEAR |
| Парткод: | 1058003 |
| Деталь: | COLLASR |
| Парткод: | 1058004 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058005 |
| Деталь: | GEAR |
| Парткод: | 1058006 |
| Деталь: | GEAR |
| Парткод: | 1058007 |
| Деталь: | HOLDER |
| Парткод: | 1058009 |
| Деталь: | GEAR |
| Парткод: | 1058010 |
| Деталь: | HOLDER |
| Парткод: | 1058011 |
| Деталь: | HOLDER |
| Парткод: | 1058012 |
| Деталь: | LEVER |
| Парткод: | 1058014 |
| Деталь: | PULLEY |
| Парткод: | 1058015 |
| Деталь: | TIMINGBELT |
| Парткод: | 1058016 |
| Деталь: | GEAR |
| Парткод: | 1058017 |
| Деталь: | SHAFT |
| Парткод: | 1058018 |
| Деталь: | ROLL |
| Парткод: | 1058020 |
| Деталь: | GUIDE ASSY |
| Парткод: | 1058021 |
| Деталь: | BUSHING |
| Парткод: | 1058025 |
| Деталь: | SCREW |
| Парткод: | 1047417 |
| Деталь: | SHAFT |
| Парткод: | 1061699 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058028 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1058029 |
| Деталь: | HOLDER |
| Парткод: | 1058030 |
| Деталь: | ROLL |
| Парткод: | 1058031 |
| Деталь: | LABEL |
| Парткод: | 1058400 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058032 |
| Деталь: | ROLL |
| Парткод: | 1058033 |
| Деталь: | GUIDE ASSY |
| Парткод: | 1058034 |
| Деталь: | LABEL |
| Парткод: | 1061702 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058035 |
| Деталь: | GUIDE ASSY |
| Парткод: | 1058036 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036345 |
| Деталь: | BRACKET |
| Парткод: | 1058038 |
| Деталь: | STOPPER |
| Парткод: | 1042718 |
| Деталь: | GUIDE ASSY |
| Парткод: | 1090711 |
| Деталь: | COVER |
| Парткод: | 1090706 |
| Деталь: | SCREW |
| Парткод: | 1057962 |
| Деталь: | RIGHT COVER |
| Парткод: | 1057963 |
| Деталь: | RIGHT COVER |
| Парткод: | 1057964 |
| Деталь: | RIGHT COVER |
| Парткод: | 1057965 |
| Деталь: | COVER |
| Парткод: | 1090707 |
| Деталь: | TOP COVER |
| Парткод: | 1090708 |
| Деталь: | FILTER |
| Парткод: | 1057968 |
| Деталь: | COVER |
| Парткод: | 1090709 |
| Деталь: | RIGHT COVER |
| Парткод: | 1057970 |
| Деталь: | RIGHT COVER |
| Парткод: | 1057971 |
| Деталь: | REAR COVER |
| Парткод: | 1057972 |
| Деталь: | LEFT COVER |
| Парткод: | 1057973 |
| Деталь: | TRAY |
| Парткод: | 1090710 |
| Деталь: | PAWL |
| Парткод: | 1057975 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1057976 |
| Деталь: | LABEL |
| Парткод: | 1058399 |
| Деталь: | PLATE SUPRING |
| Парткод: | 1057977 |
| Деталь: | SET PLATE |
| Парткод: | 1057978 |
| Деталь: | COVER |
| Парткод: | 1057979 |
| Деталь: | LABEL |
| Парткод: | 1061760 |
| Деталь: | FRONT COVER |
| Парткод: | 1057980 |
| Деталь: | LABEL,DC/PH/I.T.U CHANGE |
| Парткод: | 1057796 |
| Деталь: | BAND |
| Парткод: | 1057981 |
| Деталь: | GUIDE |
| Парткод: | 1058134 |
| Деталь: | RACK ASSY |
| Парткод: | 2036467 |
| Деталь: | AXLE PLATE ASSY |
| Парткод: | 1058135 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036345 |
| Деталь: | STOPPER |
| Парткод: | 1047329 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058136 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1058137 |
| Деталь: | BUSHING |
| Парткод: | 1058138 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058139 |
| Деталь: | LEVER |
| Парткод: | 1058140 |
| Деталь: | SOUND SHIELD |
| Парткод: | 1058141 |
| Деталь: | LEVER |
| Парткод: | 1058145 |
| Деталь: | GEAR |
| Парткод: | 1058146 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1058147 |
| Деталь: | BUSHING |
| Парткод: | 1058148 |
| Деталь: | GEAR |
| Парткод: | 1058149 |
| Деталь: | LEVER |
| Парткод: | 1058151 |
| Деталь: | KNOB ASSY |
| Парткод: | 1058152 |
| Деталь: | PWB ASSY |
| Парткод: | 2036362 |
| Деталь: | SHAFT |
| Парткод: | 1058156 |
| Деталь: | TRANSFER BELT UNIT |
| Парткод: | 2035704 |
| Деталь: | TRANSPORT ASSY |
| Парткод: | 1058318 |
| Деталь: | HOLDER |
| Парткод: | 1058319 |
| Деталь: | STOPPER |
| Парткод: | 1046713 |
| Деталь: | PLATE SPRING |
| Парткод: | 1058320 |
| Деталь: | GEAR |
| Парткод: | 1058321 |
| Деталь: | GEAR |
| Парткод: | 1058322 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058323 |
| Деталь: | HOLDER |
| Парткод: | 1058324 |
| Деталь: | DRUM |
| Парткод: | 1058271 |
| Деталь: | GEAR |
| Парткод: | 1058325 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058326 |
| Деталь: | GEAR |
| Парткод: | 1058327 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036345 |
| Деталь: | COLLAR |
| Парткод: | 1058328 |
| Деталь: | HOLDER |
| Парткод: | 1058329 |
| Деталь: | HUMIDITY CONVERTION EL |
| Парткод: | 2036393 |
| Деталь: | SWITCH (SW21) |
| Парткод: | 2027851 |
| Деталь: | BUSHING |
| Парткод: | 1040895 |
| Деталь: | ROLLER ASSY |
| Парткод: | 1058330 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058331 |
| Деталь: | SHAFT |
| Парткод: | 1046968 |
| Деталь: | ACTUATOR |
| Парткод: | 1058332 |
| Деталь: | BUSHING |
| Парткод: | 1058333 |
| Деталь: | SOLENOID |
| Парткод: | 2056354 |
| Деталь: | GUIDE |
| Парткод: | 1058334 |
| Деталь: | RUBBER FOOT |
| Парткод: | 1046693 |
| Деталь: | GUIDE |
| Парткод: | 1058335 |
| Деталь: | GUIDE |
| Парткод: | 1058336 |
| Деталь: | SOLENOID |
| Парткод: | 2056354 |
| Деталь: | TORSION SPRING |
| Парткод: | 1058266 |
| Деталь: | GEAR |
| Парткод: | 1058267 |
| Деталь: | GEAR |
| Парткод: | 1058268 |
| Деталь: | CAM |
| Парткод: | 1058269 |
| Деталь: | CLUTCH SPRING |
| Парткод: | 1058270 |
| Деталь: | DRUM |
| Парткод: | 1058271 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 2036345 |
| Деталь: | STOPPER |
| Парткод: | 1047329 |
| Деталь: | SEPATATOR ASSY |
| Парткод: | 1058272 |
| Деталь: | SPONGE |
| Парткод: | 1046844 |
| Деталь: | ROLLER |
| Парткод: | 1058273 |
| Деталь: | ACUTUATOR |
| Парткод: | 1058274 |
| Деталь: | HOLDER |
| Парткод: | 1058275 |
| Деталь: | TRAY |
| Парткод: | 1058276 |
| Деталь: | COVER |
| Парткод: | 1058277 |
| Деталь: | MULTIPLE TRAY ASSY |
| Парткод: | 2036384 |
| Деталь: | SIDE OPEN ASSY |
| Парткод: | 2056516 |
| Деталь: | POWER SUPPLY |
| Парткод: | 2036356 |
| Деталь: | HV TRANSFORMER |
| Парткод: | 2036349 |
| Деталь: | PWB SUPPORT 6.35H |
| Парткод: | 1046926 |
| Деталь: | PWB ASSY |
| Парткод: | 2048957 |
| Деталь: | REAR COVER |
| Парткод: | 1058084 |
| Деталь: | COVER |
| Парткод: | 1058086 |
| Деталь: | COVER |
| Парткод: | 1058087 |
| Деталь: | COVER |
| Парткод: | 1031628 |
| Деталь: | BRACKET |
| Парткод: | 1058100 |
| Деталь: | GROUND PLATE |
| Парткод: | 1031619 |
| Деталь: | HV TRANSFORMER |
| Парткод: | 2036351 |
| Деталь: | HV TRANSFORMER |
| Парткод: | 2049035 |
| Деталь: | COVER |
| Парткод: | 1058088 |
| Деталь: | PWB SUPPORT 9.53H |
| Парткод: | 1047609 |
| Деталь: | FUN MOTOR |
| Парткод: | 2036352 |
| Деталь: | SWITCH |
| Парткод: | 2036353 |
| Деталь: | HARNESS ASSY |
| Парткод: | 2036354 |
| Деталь: | TENSION SPRING |
| Парткод: | 1058092 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 1058093 |
| Деталь: | CONTACT |
| Парткод: | 1058094 |
| Деталь: | GUIDE ASSY |
| Парткод: | 1058096 |
| Деталь: | MICRO SWITCH |
| Парткод: | 2030612 |
| Деталь: | PWB SUPPORT |
| Парткод: | 1058097 |
| Деталь: | EARTH GROUND |
| Парткод: | 1058099 |
Коды ошибок
0017
0081
0082
0083
0084
0085
0086
0087
0088
0089
0090
0091
0092
0093
0094
0095
0096
0097
0098
0128 ... 0254
0255
0256
0257
0258
0800
0998
0999
1002
1010
1020
1021
1120
1121
1122
1123
1200
1210
1400
1500
1550
1600
1610
1999
2000
6004
6008
6009
6011
6012
6013
6014
6015
6016
6018
6020
6021
6022
6023
6024
6025
6026
6027
6028
6029
6030
6031
6032
6033
6034
6041
6042
6043
6044
6998
Описание
| Error code: | 0017 |
| Display: | P MOTOR 2 |
| Description: | Intermediate transport motor malfunction • The intermediate transport motor does not rotate evenly even after the lapse of a given period of time while it is being started. • The motor lock signal remains HIGH for a given period of consecutive time while the intermediate transport motor is being rotated. |
| Causes: | • Transport motor (M2) • Printer control board (PRCB) |
| Remedy: | 1 Check the M3 connector for proper connection and correct as necessary. 2 Check M3 for proper drive coupling and correct as necessary. 3 Check the MFPB connector for proper connection and correct as necessary. 4 M3 operation check MFPB PJ27MFPB-3 to 7 C-5. 5 Change M3. 6 Change MFPB. 7 Change DCPU. |
| Error code: | 0081 |
| Description: | CPU Error (TLB correction exception) |
| Error code: | 0082 |
| Description: | CPU Error (TLB miss exception [Load/Fetch]) |
| Error code: | 0083 |
| Description: | CPU Error (TLB miss exception [Store]) |
| Error code: | 0084 |
| Description: | CPU Error (Address Error Exception [Load/Fetch]) |
| Error code: | 0085 |
| Description: | CPU Error (Address Error Exception [Store]) |
| Error code: | 0086 |
| Description: | CPU Error (Bus Error Exception [Fetch]) |
| Error code: | 0087 |
| Description: | CPU Error (Bus Error Exception [Load/Store]) |
| Error code: | 0088 |
| Description: | CPU Error (SYSCALL Exception) |
| Error code: | 0089 |
| Description: | CPU Error (Break Exception) |
| Error code: | 0090 |
| Description: | SCAN MOTOR ERROR |
| Causes: | Scan Motor Deviation Error (The order from the CPU does not match the feedback of the Scan Motor.) Scan Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.) |
| Remedy: | < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. ) |
| Error code: | 0091 |
| Description: | CPU Error (Coprocessor Not Used Exception) |
| Error code: | 0092 |
| Display: | Trans. belt failure CODE (0092) Turn power off, on |
| Description: | Transfer Belt Failure The belt positioning sensor does not detect the transfer belt position detection hole a second time even after the lapse of a predetermined period of time after it has detected one while the transfer belt is rotated. |
| Causes: | • Imaging Unit, PL4.0.13 • Engine Control Board, PL13.0.20 |
| Remedy: | 1 Check the Engine Control Board connector P/J9. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Replace the Imaging Unit. Does the problem persist? Go to step 3. Complete. 3 Replace the Engine Control Board. Complete. |
| Error code: | 0093 |
| Description: | CPU Error (TLB Exception) |
| Error code: | 0094 |
| Display: | Trans. roll failure CODE (0094) Turn power off, on |
| Description: | Transfer Roll Failure Possible causes: • The 2nd Image Transfer Retraction Position Sensor(PS3) is not activated (retracted position) within a given period of time after the retraction sequence of the 2nd transfer roller has been started. • The 2nd Image Transfer Retraction Position Sensor is not deactivated (pressed position) within a given period of time after the pressure sequence of the 2nd transfer roller has been started. |
| Causes: | • 2nd Image Transfer Retraction Position Sensor (PS3), PL4.0.9 • 2nd Image Transfer Retraction Position Solenoid (SD4), PL7.2.23 • Main Motor, PL9.1.6 • Engine Control Board, PL13.0.20 |
| Remedy: | 1 Check the Main Motor connector CN37. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Main Motor for proper drive coupling and correct as necessary. Does the problem persist? Go to step 3. Complete. 3 Check the 2nd Image Transfer Retraction Position Solenoid connector CN5. Is the connector seated properly? Go to step 4. Reseat the connector. If the problem persists, go to step 4. 4 Check the 2nd Image Transfer Retraction Position Solenoid for proper drive coupling and correct as necessary. Does the problem persist? Go to step 5. Complete. 5 Check the 2nd Image Transfer Retraction Position Sensor control signal for a voltage change at P/J12-3 on the Engine Control Board. Is the signal operating correctly? Go to step 6. Replace the Engine Control Board. If the problem persists, go to step 6. 6 Replace the 2nd Image Transfer Retraction Position Solenoid. Does the problem persist? Go to step 7. Complete. 7 Replace the 2nd Image Transfer Retraction Position Sensor. Complete. |
| Error code: | 0095 |
| Description: | CPU Error (Cache Exception) |
| Error code: | 0096 |
| Display: | XFER DETACH 1 |
| Description: | Transfer Belt Separation • The 1st Image Transfer Pressure/Retraction Position Sensor doesn’t turn ON (Retracting) even after the lapse of a given period of time after the 1st Image Transfer Pressure/Retraction Clutch has turned ON during the Transfer Belt is retracting. • The 1st Image Transfer Pressure/Retraction Position Sensor doesn’t turn OFF (Pressuring) even after the lapse of a given period of time after the 1st Image Transfer Pressure/Retraction Clutch has turned ON during the Transfer Belt is pressuring. |
| Causes: | • 1st transfer pressure sensor (PS17) • Transport motor (M2) • 1st transfer pressure solenoid (SD1) • Printer control board (PRCB) |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 PC6 I/O check, Sensor check 3 CL3 operation check PWB-M CNDM1-11 (ON) K to L-2. 4 M1 operation check PWB-M CNDM1-5 (REM) PWB-M CNDM1-8 (LOCK) K to L-2. 5 Change PWB-M. |
| Error code: | 0097 |
| Description: | CPU Error (FPU Exception) |
| Error code: | 0098 |
| Description: | CPU Error (watch exception) |
| Error code: | 0128 ... 0254 |
| Description: | CPU Error (Undefined Trap) |
| Error code: | 0255 |
| Description: | CPU Error (NMI Exception) |
| Error code: | 0256 |
| Description: | CPU Error (Divide by 0) |
| Error code: | 0257 |
| Description: | CPU Error (Computation Overflow) |
| Error code: | 0258 |
| Description: | CPU Error (Break was generated) |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0998 |
| Description: | Engine communication error (Only when powering on) |
| Remedy: | 1 • Initial checking: Is there any parts of wrong specifications used, improper mounting, damage, distortion, dirt, or adherence of foreign matter? • Major parts to be checked: COMMUNICATION PWB,MCU PWB Replace or reinstall the relevant part. Go to step 2 2 Does the error occur when the power is turned ON? Go to step 3 Go to the relevant FIP when other errors/status codes occur. 3 Does the error occur when MCU PWB is replaced and the power is turned ON again? Go to FIP-2.33 “Noise” Problem solved |
| Error code: | 0999 |
| Description: | No Engine Flash ROM program data |
| Remedy: | 1 • Initial checking: Is there any parts of wrong specifications used, improper mounting, damage, distortion, dirt, or adherence of foreign matter? • Major parts to be checked: COMMUNICATION PWB,MCU PWB Replace or reinstall the relevant part. Go to step 2 2 Does the error occur when the power is turned ON? Go to step 3 Go to the relevant FIP when other errors/status codes occur. 3 Does the error occur when MCU PWB is replaced and the power is turned ON again? Go to FIP-2.33 “Noise” Problem solved |
| Error code: | 1002 |
| Description: | Standard RAM error (When the standard size is not determined, etc.) |
| Remedy: | 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Checking the SD-RAM: • Remove all SD-RAMs from the RAM slots and then reinsert them in the RAM slots. Be sure to insert the SD-RAMs one by one (S0 and S1) in order so that the SD-RAM error can be identified. Every time you insert an SD-RAM, follow the procedures below and repeat it for each one. 1 Turn the power off. 2 Add the SD-RAM 3 Turn the power on. • Insert the SD-RAM in the socket until it is locked securely. NOTE: Since the SD-RAM has the right direction to insert, be sure to insert it in the correct direction. Replace or reinstall the relevant part. Problem solved |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1021 |
| Display: | Papr Type Mismatch |
| Description: | RAM Error (Slot 1) |
| Error code: | 1120 |
| Description: | Paper feeder left lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 1 does not turn on within 30 s of paper feeder lift motor 2 turning on. |
| Causes: | Poor contact in the connector terminals. Defective paper feeder lift switch 1. Defective paper feeder lift motor 2. The paper feeder left lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper feeder lift switch 1. Check if YC5-4 on the paper feeder main PWB goes low when paper feeder lift switch 1 is turned off. If not, replace paper feeder lift switch 1. Defective paper feeder lift motor 2. Check for continuity across the coil. If none, replace paper feeder lift motor 2. The paper feeder left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | 1121 |
| Description: | CR reverse error An abnormal operation (reveres movement) of the carriage was detected a predetermined number of times. |
| Remedy: | Check the CR scale (SCALE, CR) for incorrect attachment, scratch, dirt, and fix any abnormality. Replace the CR scale (SCALE, CR). Replace the CR encoder (BOARD ASSY., ENCODER, CR). |
| Error code: | 1122 |
| Description: | CR overspeed error The carriage moved faster than a designated level. |
| Remedy: | Check the CR scale (SCALE, CR) for incorrect attachment, scratch, dirt, and fix any abnormality. Replace the CR encoder (BOARD ASSY., ENCODER, CR). Replace the CR motor (MOTOR ASSY., CR). Replace the main board (BOARD ASSY., MAIN). |
| Error code: | 1123 |
| Description: | Duty over error An abnormal load is applied to the CR motor. |
| Remedy: | Check the carriage shaft surface for any foreign matters, and remove it if any. Check that the carriage shaft and the contact points between the carriage unit and the main frame are properly lubricated. Replace the CR motor (MOTOR ASSY., CR). |
| Error code: | 1200 |
| Description: | Side registration motor error The duplexer PWB of the optional duplexer cannot detect the home position of the adjust guide. |
| Causes: | Defective duplexer. Defective engine controller PWB (A0004). |
| Remedy: | Defective duplexer. Refer to the duplexer`s service manual. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). |
| Error code: | 1210 |
| Description: | Mode Select An invalid print mode was selected in the print command. |
| Causes: | Defective side registration home position sensor. Defective side registration motor. Defective engine controller PWB (KP-992). |
| Remedy: | Resend the print job. If the problem remains, then reinstall the printer driver. Service: Resend the print job. If the problem remains, then reinstall the print driver. |
| Error code: | 1400 |
| Display: | Condensation Leave switched ON. Fully open the Front Cover. Wait 30 minutes, switch OFF and close cover, then switch ON. |
| Description: | Rotary guide motor error The guide sensor is not detected to be on at the home position detection with the rotary guide for three times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective BR guide motor. Defective BR main PWB. Defective engine PWB. |
| Remedy: | Rotary guide motor 1. Check the rotary guide and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Rotary guide motor and BR PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the rotary guide motor. BR PWB Replace the BR PWB. |
| Error code: | 1500 |
| Display: | Print Unable 15 Turn the power off and then back on again. |
| Description: | PF heater 1 high temperature error (paper feeder 1) A temperature higher than 75C/167F is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Shorted PF thermistor 1. Defective PF fan motor 1. Defective PF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 1 and PF main PWB (YC111) Shorted PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder). Defective PF fan motor 1. Replace the top heater unit (Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1550 |
| Description: | PF heater 2 high temperature error (paper feeder 3) A temperature higher than 75C/167F is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Shorted PF thermistor 2. Defective PF fan motor 2. Defective PF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 2 and PF main PWB (YC111) Shorted PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder). Defective PF fan motor 2. Replace the side heater unit (Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1600 |
| Description: | PF heater 1 low temperature error (paper feeder 1) An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on. |
| Causes: | Defective connector cable or poor contact in the connector. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. Broken PF heater 1. Defective PF heater PWB or PF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 1 and PF heater PWB (YC1) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 1 and PF main PWB (YC114) PF thermistor 1 installed incorrectly. Check the installation of the PF thermistor 1. Defective PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder). Broken PF heater 1. Replace the top heater unit (Refer to the service manual for the paper feeder). Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1610 |
| Description: | PF heater 2 low temperature error (paper feeder 1) An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on. |
| Causes: | Defective connector cable or poor contact in the connector. PF thermistor 2 installed incorrectly. Defective PF thermistor 2. Broken PF heater 2. Defective PF heater PWB or PF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 2 and PF heater PWB (YC2) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 2 and PF main PWB (YC115) PF thermistor 2 installed incorrectly. Check the installation of the PF thermistor 2. Defective PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder). Broken PF heater 2. Replace the side heater unit (Refer to the service manual for the paper feeder). Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1999 |
| Description: | Other hardware error |
| Remedy: | 1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Initializing the MCU PWB: • By using the DIAG command, execute “Slave Initialize”. Turn the power off once and on again. Does the printer operate normally? Problem solved Go to step 3 3 • Replacing the relevant unit: • Replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 6004 |
| Display: | Cover is Open Close the Back Cover of the machine. |
| Description: | Engine board error When a communication error in the Engine Board (PWB-A) is detected |
| Causes: | • Engine Board (PWB-A) |
| Remedy: | 1 Replace the PWB-A. |
| Error code: | 6008 |
| Description: | Main motor error When the Main Motor (M1) does not operate at turning on the power switch. |
| Causes: | • Main Motor (M1) • Engine Board (PWB-A) • Power Supply Unit (PU) |
| Remedy: | 1 Check the operation of M1. M1_REM 2 Replace the PU. - - 3 Replace the PWB-A. |
| Error code: | 6009 |
| Description: | Fuser motor error |
| Causes: | Detection of fusing motor (M4) rotation is detected 1 second after fusing motor (M4) starts rotating until the fusing motor (M4) stops. When the fusing motor M_Lock signal becomes active for 0.5 seconds, the printer detects that the fusing motor is abnormal. |
| Remedy: | 1 Does the fusing motor (M4) rotate during printing? No Remove connector PJ22A and insert it again. Yes Check that no weight applies on the each roller or gears. Others Replace PWB-A. |
| Error code: | 6011 |
| Description: | Exhaust fan error When the Exhaust Fan Motor (M6) does not operate at turning on the main switch. |
| Causes: | • Exhaust Fan Motor (M6) • Engine Board (PWB-A) • Power Supply Unit (PU) |
| Remedy: | 1 Check the operation of M6. M6_REM 2 Replace the PU. - - 3 Replace the PWB-A. |
| Error code: | 6012 |
| Description: | Power coolant fan error When the Power Coolant Fan Motor (M4) does not operate at turning on the main switch. |
| Causes: | • Power Supply Cooling Fan Motor (M4) • Engine Board (PWB-A) • Power Supply Unit (PU) |
| Remedy: | 1 Check the operation of M4. M4_REM 2 Replace the PU. - - 3 Replace the PWB-A. |
| Error code: | 6013 |
| Description: | Internal cooling fan error |
| Remedy: | 1 At the power ON initialization sequence, does the suction fan motor (M7) rotate? Check the rotation by its sound or by hand feeling wind. No Remove connector PJ3A and insert it again. Replace the fan motor. Others Replace PWB-A. |
| Error code: | 6014 |
| Description: | Fuser cooling fan error When the Fuser Cooling Fan Motor (M5) does not operate at turning on the main switch. |
| Causes: | • Fuser Cooling Fan Motor (M5) • Engine Board (PWB-A) • Power Supply Unit (PU) |
| Remedy: | 1 Check the operation of M5. M5_REM 2 Replace the PU. - - 3 Replace the PWB-A. |
| Error code: | 6015 |
| Description: | Fuser fan error |
| Causes: | Fusing fan motor (M10) rotates by two rotational speed; full speed / half speed. .. When fan is booted or warm-up is completed: Full speed for 2 seconds, and then half speed .. When transportation motor (M1) is rotating: Full speed .. When warm-up is completed: Half speed .. Cover open, pause: Stop When the fusing fan lock signal becomes active for 0.5 seconds, the printer detects that fusing fan motor is abnormal. |
| Remedy: | 1 At the power ON initialization sequence, does the fusing fan motor (M10) rotate? Check the rotation by its sound or by hand feeling wind. No Remove connector PJ29A and insert it again. Replace the fan motor. Others Replace PWB-A. |
| Error code: | 6016 |
| Description: | Polygon motor error When the Polygon Motor does not operate, or the laser diode (LD) does not emit the laser beam. |
| Causes: | • Print Head Unit • Engine Board (PWB-A) • Power Supply Unit (PU) |
| Remedy: | 1 Replace the print head unit. - - 2 Replace the PU. - - 3 Replace the PWB-A. |
| Error code: | 6018 |
| Description: | Laser error When the Polygon Motor does not operate, or the laser diode (LD) does not emit the laser beam. |
| Causes: | • Print Head Unit • Engine Board (PWB-A) • Power Supply Unit (PU) |
| Remedy: | 1 Replace the print head unit. - - 2 Replace the PU. - - 3 Replace the PWB-A. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6021 |
| Description: | Transfer belt cleaner clearance error When pressing or separation of the Transfer Belt Cleaner is impossible. |
| Causes: | • Cleaner Pressure Flapper Solenoid (SL4) • Belt Cleaner Position Detect Sensor (PC9) • Engine Board (PWB-A) |
| Remedy: | 1 Check the operation of PC9. PC9_ON 2 Replace the pressing/separation mechanism parts of the Belt Cleaner. - - 3 Check the operation of SL4. SL4_REM 4 Replace the PWB-A. |
| Error code: | 6022 |
| Description: | Transfer belt rotation error When the transfer belt of the Intermediate Transfer Belt Unit does not operate. |
| Remedy: | 1 Replace the transfer belt unit. |
| Error code: | 6023 |
| Description: | Developing rack rotation error When the Toner Cartridge Rack does not turn. |
| Causes: | • Rack motor (M2) • Rack Clutch (CL1) • Rack Black Position Detection Sensor (PC4) • Engine Board (PWB-A) |
| Remedy: | 1 Check the operation of PC4. PC4_ON 2 Check the operation of M2. CL1_REM 3 Check the operation of CL1. - 4 Replace the PWB-A. |
| Error code: | 6024 |
| Description: | Fuser roller / warming up error When 80C is not reached in 100 seconds after start of warming up. When the fusing roller temperature has dropped and remained below 70C for 10 seconds during standby. |
| Causes: | • Fusing Roller Heater Lamp (H1) • Pressure Roller Heater Lamp (H2) • Thermostat (TS1) • Engine Board (PWB-A) • Power Supply Unit (PU) |
| Remedy: | 1 Check the continuity of H1 and H2. NO Replace the H1, H2. - 2 Check the continuity of TS1. NO Replace the TS1. - 3 Check to see if the resistance of TH1 is infinite. (Between CN18-1 and 2 on thermistor side) YES Clean TH1 or replace the Fuser Unit. HEATER NO Replace the PU. Replace the PWB-A. |
| Error code: | 6025 |
| Description: | Fusing roller / low temperature error When 80C is not reached in 100 seconds after start of warming up. When the fusing roller temperature has dropped and remained below 70C for 10 seconds during standby. |
| Causes: | • Fusing Roller Heater Lamp (H1) • Pressure Roller Heater Lamp (H2) • Thermostat (TS1) • Engine Board (PWB-A) • Power Supply Unit (PU) |
| Remedy: | 1 Check the continuity of H1 and H2. NO Replace the H1, H2. - 2 Check the continuity of TS1. NO Replace the TS1. - 3 Check to see if the resistance of TH1 is infinite. (Between CN18-1 and 2 on thermistor side) YES Clean TH1 or replace the Fuser Unit. HEATER NO Replace the PU. Replace the PWB-A. |
| Error code: | 6026 |
| Description: | Fusing roller / high temperature error When the Fusing Roller temperature is 220°C or higher for 0.1 second. When between 40 seconds and 50 seconds after start of warming up of the Fusing Roller, the Fusing Roller temperature does not rise for one second by 5°C from that at start of fuser warming up. |
| Causes: | • Thermistor (TH1) • Engine Board (PWB-A) |
| Remedy: | 1 Check to see if TH1 is shorted. (Between CN18-1 and 2 on thermistor side) YES Clean TH1. HEATER Replace the Fuser Unit. NO Replace the PU. Replace the PWB-A. |
| Error code: | 6027 |
| Description: | Fusing roller / thermistor error When the Fusing Roller temperature is 220°C or higher for 0.1 second. When between 40 seconds and 50 seconds after start of warming up of the Fusing Roller, the Fusing Roller temperature does not rise for one second by 5°C from that at start of fuser warming up. |
| Causes: | • Thermistor (TH1) • Engine Board (PWB-A) |
| Remedy: | 1 Check to see if TH1 is shorted. (Between CN18-1 and 2 on thermistor side) YES Clean TH1. HEATER Replace the Fuser Unit. NO Replace the PU. Replace the PWB-A. |
| Error code: | 6028 |
| Description: | Pressure roller heating error |
| Causes: | 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C. |
| Remedy: | 1 Check the connection between the fusing unit and connector. - Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A. |
| Error code: | 6029 |
| Description: | Pressure roller low temperature error |
| Causes: | 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C. |
| Remedy: | 1 Check the connection between the fusing unit and connector. - Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6031 |
| Description: | Pressure roller thermistor error |
| Causes: | 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C. |
| Remedy: | 1 Check the connection between the fusing unit and connector. - Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A. |
| Error code: | 6032 |
| Description: | Fuser roller gap control error |
| Causes: | 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C. |
| Remedy: | 1 Check the connection between the fusing unit and connector. - Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A. |
| Error code: | 6033 |
| Description: | Transparency detection sensor error Transparency is not detected. |
| Causes: | • OHP Sensor (PC3A) • Engine Board (PWB-A) |
| Remedy: | 1 Check the operation of PC3A. PC3_REM 2 Replace the PWB-A. |
| Error code: | 6034 |
| Description: | Multiple manual feeder pusher error |
| Causes: | 1. MPT push-up tray position is detected while loading paper from the manual tray. 2. If the output of the manual tray upper position sensor (PC15) does not change even after the specified amount of time passed after the manual tray paper load solenoid (SL8) becomes ON, it is detected that the MPT push-up plate is abnormal. |
| Remedy: | Does the manual tray push paper to the paper load roller? No Arrange paper on the manual tray. 2 Does the manual tray paper load roller one-way clutch have the claws? No Replace the one-way clutch gear. Yes Replace the manual tray paper load solenoid. Others Replace PWB-A. |
| Error code: | 6041 |
| Description: | Memory counter error EEPROM error detection |
| Causes: | • EEPROM • Engine Board (PWB-A) |
| Remedy: | 1 Replace the EEPROM. - - 2 Replace the PWB-A. |
| Error code: | 6042 |
| Description: | Memory data error EEPROM error detection |
| Causes: | • EEPROM • Engine Board (PWB-A) |
| Remedy: | 1 Replace the EEPROM. - - 2 Replace the PWB-A. |
| Error code: | 6043 |
| Description: | Memory access error EEPROM error detection |
| Causes: | • EEPROM • Engine Board (PWB-A) |
| Remedy: | 1 Replace the EEPROM. - - 2 Replace the PWB-A. |
| Error code: | 6044 |
| Description: | Memory installation error EEPROM error detection |
| Causes: | • EEPROM • Engine Board (PWB-A) |
| Remedy: | 1 Replace the EEPROM. - - 2 Replace the PWB-A. |
| Error code: | 6998 |
| Description: | Engine communication error Any error has occurred in communication through the video interfere between the Main Board and the Engine Board. |
| Causes: | • Main Board (C494MAIN) • Engine Board (PWB-A) |
| Remedy: | 1 Check the connection between Main Board and Engine Board. - - 2 Replace the Main Board (C494MAIN). - - 3 Replace the Engine Board (PWB-A). |
Парткод
Название
EPSON Тонер-картридж черный
EPSON Тонер-картридж желтый
EPSON Тонер-картридж пурпурный
EPSON Тонер-картридж голубой
EPSON Сборник отработанного тонера
EPSON Блок фотобарабана
EPSON Масляный вал
EPSON Ремень перноса изображения
EPSON Блок термозакрепления (печка)
