Epson AcuLaser C2600
Рейтинг
Модули
C585-E LE C-01 (02)
C585-ME CH-01 (04)
C585-ME CH-06 (09)
C585-E LE C-02 (03)
C585-ME CH-04 (07)
C585-ME CH-02 (05)
C585-CAS E -01 (01)
C585-ME CH-05 (08)
C585-ME CH-03 (06)
Детали C585-CAS E -01 (01)
| Деталь: | BRACKET ASSY.,I/F |
| Парткод: | 1291992 |
| Деталь: | NETWORK BOARD |
| Парткод: | 2085196 |
| Деталь: | GROUNDING PLATE,TYPE-B |
| Парткод: | 1295979 |
| Деталь: | GUIDE RAIL |
| Парткод: | 1012848 |
| Деталь: | HARNESS,MAIN,PS |
| Парткод: | 2090855 |
| Деталь: | HARNESS,MAIN,SIGNAL |
| Парткод: | 2090854 |
| Деталь: | HARNESS,HV,2ST TRANSFER |
| Парткод: | 2090373 |
| Деталь: | BOARD ASSY.,MEMORY |
| Парткод: | 2090603 |
| Деталь: | BOARD ASSY.,MEMORY |
| Парткод: | 2090587 |
| Деталь: | BOARD ASSY., MAIN |
| Парткод: | 2101818 |
| Деталь: | BOARD ASSY., MAIN |
| Парткод: | 2101819 |
| Деталь: | BOARD ASSY.,DRV |
| Парткод: | 2090593 |
| Деталь: | HARNESS,MAIN |
| Парткод: | 2090363 |
| Деталь: | MOUNTING PLATE Assy.,CONTROLLER |
| Парткод: | 1291983 |
| Деталь: | COVER,TYPE-B |
| Парткод: | 1295981 |
| Деталь: | HARNESS,DR,DV |
| Парткод: | 2090375 |
| Деталь: | STEPPING MOTOR ASSY.,DV |
| Парткод: | 2090437 |
| Деталь: | CLUTCH,CLEANER |
| Парткод: | 1293652 |
| Деталь: | BUSHING,8 |
| Парткод: | 1113335 |
| Деталь: | SPECSER,CLUTCH |
| Парткод: | 1294638 |
| Деталь: | TIMING BELT |
| Парткод: | 1293656 |
| Деталь: | PULLEY ASSY.,DRIVE,ASP |
| Парткод: | 1410690 |
| Деталь: | CLUTCH,2ND TRANSFER |
| Парткод: | 1294637 |
| Деталь: | DRIVE ASSY.,FU,ASP |
| Парткод: | 1410689 |
| Деталь: | SERVOMOTOR,DRIVE |
| Парткод: | 2090618 |
| Деталь: | DRIVE ASSY.,MAIN,ASP |
| Парткод: | 1410691 |
| Деталь: | DRIVE ASSY.,MPT,ASP |
| Парткод: | 1410687 |
| Деталь: | CLUTCH,PICK UP |
| Парткод: | 2090643 |
| Деталь: | DRIVE ASSY.,MPC,ASP |
| Парткод: | 1410688 |
| Деталь: | CLUTCH,FEED |
| Парткод: | 2090642 |
| Деталь: | SERVOMOTOR,PC |
| Парткод: | 2090555 |
| Деталь: | CLUTCH,GATE |
| Парткод: | 2090641 |
| Деталь: | LOCK ASSY.,RT,ASP |
| Парткод: | 1410692 |
| Деталь: | DRIVE ASSY.,RT,ASP |
| Парткод: | 1407957 |
| Деталь: | FAN,FU |
| Парткод: | 2090319 |
| Деталь: | COVER,RIGHT |
| Парткод: | 1293690 |
| Деталь: | PAPER GUIDE,FRONT,MP |
| Парткод: | 1293696 |
| Деталь: | LEVER,GUIDE,MP |
| Парткод: | 1293744 |
| Деталь: | COMPRESSION SPRING,8.51 |
| Парткод: | 1293745 |
| Деталь: | PAPER GUIDE,REAR,MP |
| Парткод: | 1293697 |
| Деталь: | LIFT PLATE ASSY.,MP,ASP |
| Парткод: | 1407958 |
| Деталь: | TORSION SPRING,55.09 |
| Парткод: | 1293743 |
| Деталь: | SPUR GEAR,16,MPT |
| Парткод: | 1293698 |
| Деталь: | LEVER,REAR,MP |
| Парткод: | 1293727 |
| Деталь: | COMPRESS SPRING,2.52 |
| Парткод: | 1293753 |
| Деталь: | LEVER,UPPER,MP |
| Парткод: | 1294745 |
| Деталь: | PAPER SUPPORT,MP |
| Парткод: | 1293699 |
| Деталь: | PAPER SUPPORT,SUB,MP |
| Парткод: | 1293700 |
| Деталь: | HOUSING,MP |
| Парткод: | 1293694 |
| Деталь: | LEVER,FRONT,MP |
| Парткод: | 1293704 |
| Деталь: | COVER,PICK UP,MP |
| Парткод: | 1293691 |
| Деталь: | ROLLER ASSY.,SEPARATION,ASP |
| Парткод: | 1407960 |
| Деталь: | LEVER,PE |
| Парткод: | 1293707 |
| Деталь: | ROLLER,PAPER LOAD |
| Парткод: | 1111834 |
| Деталь: | STOPPER,4 |
| Парткод: | 1218776 |
| Деталь: | CONNECTOR,DUPLEX |
| Парткод: | 2090928 |
| Деталь: | COMPRESSION SPRING,9.99 |
| Парткод: | 1291898 |
| Деталь: | PIN,DUPLEX |
| Парткод: | 1294742 |
| Деталь: | COVER,UPPER,MP |
| Парткод: | 1293692 |
| Деталь: | DETECTOR,HP |
| Парткод: | 2032842 |
| Деталь: | LEVER,PE,SUB |
| Парткод: | 1293747 |
| Деталь: | CLUTCH,PICK UP,MP |
| Парткод: | 2090627 |
| Деталь: | CLUTCH,2ND TRANSFER |
| Парткод: | 1294637 |
| Деталь: | EXTENSION SPRING,7.29 |
| Парткод: | 1293722 |
| Деталь: | LEVER ASSY.,GUIDE,ASP |
| Парткод: | 1407959 |
| Деталь: | COMPRESSION SPRING,8.82 |
| Парткод: | 1293734 |
| Деталь: | GREASE G-52 |
| Парткод: | 1049527 |
| Деталь: | GREASE G-30 (40GR)[B703000001] |
| Парткод: | 1080617 |
| Деталь: | Grease G-66 |
| Парткод: | 1298593 |
| Деталь: | GREASE G-73 |
| Парткод: | 1407972 |
| Деталь: | GREASE G74 |
| Парткод: | 1409257 |
| Деталь: | HARNESS,HV,1ST TRANSFER |
| Парткод: | 2090372 |
| Деталь: | HIGH VOLTAGE POWER SUPPLY |
| Парткод: | 2090848 |
| Деталь: | DETECTOR,PC |
| Парткод: | 2090329 |
| Деталь: | HARNESS,HP |
| Парткод: | 2090551 |
| Деталь: | LEAF SPRING,ELCTRODE,DV |
| Парткод: | 1293678 |
| Деталь: | EDGE SADDLE |
| Парткод: | 1113999 |
| Деталь: | HARNESS,INRET |
| Парткод: | 2090849 |
| Деталь: | POWER SWITCH |
| Парткод: | 2071776 |
| Деталь: | HARNESS,AC,200 |
| Парткод: | 2090853 |
| Деталь: | POWER SUPPLY(230V) |
| Парткод: | 2090847 |
| Деталь: | R/W Module |
| Парткод: | 2090859 |
| Деталь: | BEARING,688ZZNR |
| Парткод: | 1114035 |
| Деталь: | GUIDE,GATE,LEFT |
| Парткод: | 1293818 |
| Деталь: | DETECTOR ASSY.,GUIDE,GATE,INNER,ASP |
| Парткод: | 1410693 |
| Деталь: | HARNESS,PAPER LOAD |
| Парткод: | 2090364 |
| Деталь: | BRACKET ASSY.,PE,ASP |
| Парткод: | 2103124 |
| Деталь: | DETECTOR,HUMIDITY |
| Парткод: | 2090631 |
| Деталь: | COVER Assy.,DV,Y,ASP |
| Парткод: | 1410681 |
| Деталь: | COVER Assy.,DV,K,ASP |
| Парткод: | 1410684 |
| Деталь: | COVER Assy.,DV,M,ASP |
| Парткод: | 1410682 |
| Деталь: | COVER Assy.,DV,C,ASP |
| Парткод: | 1410683 |
| Деталь: | FRAME ASSY.,RT,ASP |
| Парткод: | 1410680 |
| Деталь: | BOARD ASSY.,MEMORY |
| Парткод: | 2090583 |
| Деталь: | ERASER |
| Парткод: | 2090863 |
| Деталь: | HARNESS,ERASER |
| Парткод: | 2100125 |
| Деталь: | BUSHING,8 |
| Парткод: | 1113335 |
| Деталь: | 2nd TRANSFER ASSY |
| Парткод: | 1413999 |
| Деталь: | ROLLER,2ND,B |
| Парткод: | 1413996 |
| Деталь: | MOUNTING PLATE,ANTI-STATIC |
| Парткод: | 1403709 |
| Деталь: | DETECTOR,HP |
| Парткод: | 2032842 |
| Деталь: | RETAINING RING,4 |
| Парткод: | 1293673 |
| Деталь: | DETECTION,PAPER LOAD |
| Парткод: | 1113658 |
| Деталь: | DETECTOR,V-162-3A5 |
| Парткод: | 2073156 |
| Деталь: | HARNESS Assy.,I/L |
| Парткод: | 2090370 |
| Деталь: | LEVER,TENSION |
| Парткод: | 1291854 |
| Деталь: | HARNESS,AC,FU |
| Парткод: | 2090368 |
| Деталь: | Laser Scanner |
| Парткод: | 1293867 |
| Деталь: | HARNESS,LSU |
| Парткод: | 2090365 |
| Деталь: | DETECTOR,V-164-3A5 |
| Парткод: | 2073157 |
| Деталь: | TRANSFER UNIT,Assy |
| Парткод: | 1302590 |
| Деталь: | HOUSING,TOP |
| Парткод: | 1292092 |
| Деталь: | SHEET,INSULATOR |
| Парткод: | 1269590 |
| Деталь: | COVER Assy.,FU |
| Парткод: | 1302589 |
| Деталь: | COVER,TOP |
| Парткод: | 1293873 |
| Деталь: | HOUSING,REAR |
| Парткод: | 1292097 |
| Деталь: | HOUSING,CONTROLLER |
| Парткод: | 1292106 |
| Деталь: | MP TRAY Assy,ASP |
| Парткод: | 1410686 |
| Деталь: | HOUSING,RIGHT |
| Парткод: | 1292099 |
| Деталь: | LABEL,ACCESARY |
| Парткод: | 1302887 |
| Деталь: | COVER,FRONT |
| Парткод: | 1292100 |
| Деталь: | COVER,INNER |
| Парткод: | 1292101 |
| Деталь: | HOUSING,LEFT |
| Парткод: | 1292098 |
| Деталь: | CONTROL PANEL |
| Парткод: | 2090856 |
| Деталь: | HARNESS,PANEL |
| Парткод: | 2090857 |
| Деталь: | TRAY,PAPER,EJECT |
| Парткод: | 1292093 |
| Деталь: | LOGO PLATE,13X54 |
| Парткод: | 1232050 |
| Деталь: | POWER CABLE |
| Парткод: | 2082069 |
| Деталь: | POWER CABLE |
| Парткод: | 2088265 |
| Деталь: | SOFTWARE CD,E |
| Парткод: | 3100115 |
| Деталь: | SETTING UP MANUAL |
| Парткод: | 4100236 |
| Деталь: | ROLLER,FUSER,REAR |
| Парткод: | 1293836 |
| Деталь: | ROLLER,PAPER EJECT |
| Парткод: | 1293837 |
| Деталь: | BEARING,688ZZNR |
| Парткод: | 1114035 |
| Деталь: | ROLLER,GATE |
| Парткод: | 1293881 |
| Деталь: | ROLLER,FEED |
| Парткод: | 1293831 |
| Деталь: | BUSHING,8 |
| Парткод: | 1113335 |
| Деталь: | ROLLER ASSY,PICK UP |
| Парткод: | 1293802 |
| Деталь: | ROLLER,FEED |
| Парткод: | 1293830 |
| Деталь: | GUIDE ASSY.,LEFT,ASP |
| Парткод: | 1410685 |
| Деталь: | GUIDE,GATE.,ASSY,ASP |
| Парткод: | 1407961 |
| Деталь: | STANDARD CASSTTE ASSY |
| Парткод: | 1403707 |
| Деталь: | COMPRSSION SPRING,10.58 |
| Парткод: | 1298776 |
| Деталь: | EXTENSION SPRING,1.93 |
| Парткод: | 1293799 |
| Деталь: | LATCH,CASSETTE |
| Парткод: | 1293796 |
| Деталь: | HOLDER,CASSETTE |
| Парткод: | 1293797 |
| Деталь: | ELECTRODE Assy.,PC,ASP |
| Парткод: | 1410679 |
| Деталь: | DETECTOR,PC |
| Парткод: | 2090329 |
| Деталь: | FAN,PC |
| Парткод: | 2090328 |
| Деталь: | ERIBG,4,L/NA |
| Парткод: | 1114006 |
| Деталь: | PIN,RELEASE |
| Парткод: | 1293763 |
| Деталь: | LINK,RELEASE,FRONT |
| Парткод: | 1293879 |
| Деталь: | LEVER,RELEASE,FRONT |
| Парткод: | 1293878 |
| Деталь: | FOOT |
| Парткод: | 1113217 |
| Деталь: | LINK,RELEASE,REAR |
| Парткод: | 1293762 |
| Деталь: | LEVER,RELEASE,REAR |
| Парткод: | 1293761 |
| Деталь: | CLEANER ASSY |
| Парткод: | 1293869 |
| Деталь: | SENSOR,TANK |
| Парткод: | 2101816 |
| Деталь: | FILTER,OZONE |
| Парткод: | 1292011 |
| Деталь: | FILTER,OZONE |
| Парткод: | 1295974 |
| Деталь: | FAN,DUST CHAMBER |
| Парткод: | 2090315 |
| Деталь: | HARNESS,RELAY,WASTE TONER |
| Парткод: | 2090396 |
| Деталь: | LEVER,PATCH |
| Парткод: | 1291936 |
| Деталь: | DETECTOR,V-162-3A5 |
| Парткод: | 2073156 |
| Деталь: | EDGE SADDLE |
| Парткод: | 1113999 |
| Деталь: | FAN,LPS |
| Парткод: | 2090327 |
Коды ошибок
C0017
C0081
C0082
C0083
C0084
C0085
C0086
C0087
C0088
C0089
C0090
C0091
C0092
C0093
C0094
C0095
C0096
C0097
C0098
C0128 ... C0254
C0255
C0256
C0257
C0258
C0800
C0998
C1000
C1001
C1002
C1020
C1021
C1022
C1400
C1700
C1720
C1999
C2000
C999
E090
E091
E092
E093
E094
E095
E096
E111
E112
E113
E115
E116
E123
E124
E125
E126
E132
E144
E153
E154
E155
E156
E256
E998
Описание
| Error code: | C0017 |
| Description: | Imaging Unit Motor Bk turning at abnormal timing The Lock signal remains faulty for a continuous 1sec. period after the motor has completely stopped and before the motor starts accelerating. |
| Remedy: | 1 Imaging Unit Motor rotation while it is being energized: Cyan: the voltage across PJ12I-3B on Master Board and GND remains DC 0 V. Magenta: the voltage across PJ12I-7A on Master Board and GND remains DC 0 V. Yellow: the voltage across PJ12I-3A on Master Board and GND remains DC 0 V. Black: the voltage across PJ12I-7B on Master Board and GND remains DC 0 V. YES: Change Master Board. NO: Change motor. |
| Error code: | C0081 |
| Description: | CPU Error (TLB modification exception) |
| Error code: | C0082 |
| Description: | CPU Error (TLB mistake exception [Load/Fetch]) |
| Error code: | C0083 |
| Description: | CPU Error (TLB mistake exception [Store]) |
| Error code: | C0084 |
| Description: | CPU Error (address error exception [Load/Fetch]) |
| Error code: | C0085 |
| Description: | CPU Error (address error exception [Store]) |
| Error code: | C0086 |
| Description: | CPU Error (bus error exception [Fetch]) |
| Error code: | C0087 |
| Description: | CPU Error (bus error exception [Load/Store]) |
| Error code: | C0088 |
| Description: | CPU Error (SYSCALL exception) |
| Error code: | C0089 |
| Description: | CPU Error (Break exception) |
| Error code: | C0090 |
| Description: | Developing Unit Drive Motor’s failure to turn • The Lock signal remains HIGH for a continuous period of 1.5 sec. or more after the lapse of 10 sec. after the motor has started turning. • The Lock signal remains LOW for a continuous period of 1.5 sec. or more after the lapse of 10 sec. after the motor has stopped turning. |
| Remedy: | 1 Developing Unit Drive Motor rotation: the voltage across PJ7A-7A on Master Board and GND is DC5V (motor deenergized) and DC0V (motor energized) when the Start key is pressed. NO Change Master Board. 2 Developing Unit Drive Motor rotation: the voltage across PJ7A-6A on Master Board and GND is DC5V (motor deenergized) and DC0V (motor energized) when the Start key is pressed. YES Correct drive coupling. Correct installed position of the Developing Unit. Change motor. NO Change Master Board. |
| Error code: | C0091 |
| Description: | CPU Error (coprocessor unused exception) |
| Error code: | C0092 |
| Description: | CPU Error (FPU exception) |
| Error code: | C0093 |
| Description: | CPU Error (TLB exception) |
| Error code: | C0094 |
| Description: | 2nd Image Transfer Roller pressure/retraction failure • The 2nd Image Transfer Pressure Position Sensor is not activated (retracted position) within 1 sec. after the 2nd Image Transfer Roller has started its retracting motion. • The 2nd Image Transfer Pressure Position Sensor is not deactivated (not the retracted position) within 1 sec. after the 2nd Image Transfer Roller has started its pressing motion. |
| Remedy: | 1 While the 2nd Image Transfer Pressure/ Retraction Clutch is supposed to be deenergized during timing of pressure/retraction operation: the voltage across PJ14I-9A on Master Board and GND is DC 24 V when the clutch is deenergized and DC 0 V when the clutch is energized. YES: Check connector for connection. Check for overload. Change clutch. NO: Change Master Board. 2 I/O check for 2nd Image Transfer Pressure Position Sensor operation during pressure/ retraction operation: the voltage across PJ14I-6B on Master Board and GND is DC 0 V when the sensor is unblocked and DC 5 V when the sensor is blocked (pressed position). YES: Change Master Board. NO: Correct actuator. Check sensor connector for connection. Change sensor. |
| Error code: | C0095 |
| Description: | CPU Error (cache exception) |
| Error code: | C0096 |
| Description: | 1st Image Transfer Roller pressure/retraction failure • The 1st Image Transfer Retraction Position Sensor is not activated (retracted position) within 3 sec. after the 1st Image Transfer Pressure/Retraction Motor has started turning. • The 1st Image Transfer Retraction Position Sensor is not deactivated (pressed position) within 1.5 sec. after the 1st Image Transfer Pressure/Retraction Motor has started turning. |
| Remedy: | 1 1st Image Transfer Pressure/Retraction Motor turns during pressure/retraction operation. NO: Check connector for connection. Correct drive coupling (drive transmitting gear engagement). Change motor. Change Master Board. 2 I/O check for 1st Image Transfer Retraction Position Sensor operation during pressure/ retraction operation: the voltage across PJ17I-1A on Master Board and GND is DC 0 V when the sensor is unblocked and DC 5 V when the sensor is blocked (retracted position). YES: Change Master Board. NO: Correct actuator. Check sensor connector for connection. Change sensor. |
| Error code: | C0097 |
| Description: | CPU Error (FPU exception) |
| Error code: | C0098 |
| Description: | Fusing Roller pressure/ retraction failure • No change is observed in the encoder pulse even after the lapse of 0.5 sec. after the Fusing Pressure/Retraction Motor has started turning for retraction direction during retraction control. • No change is observed in the encoder pulse even after the lapse of 0.5 sec. after the Fusing Pressure/Retraction Motor has started turning for pressure direction during pressure control. • The Fusing Pressure Position Sensor is not activated (pressed position) even when 31 motor encoder pulses have been counted after the Fusing Pressure/Retraction Motor has started turning for pressure direction during pressure control. |
| Remedy: | 1 Fusing Pressure/Retraction Motor rotation when the Fusing Roller is retracted: the voltage across PJ14I-4A on Master Board and GND is DC 0 V when the motor is deenergized and DC 24 V when the motor is energized. YES: Check motor connector for connection. Change motor. NO: Change Master Board. 2 I/O check for Fusing Pressure Position Sensor when the Fusing Roller is retracted: the voltage across PJ6I-11B on Master Board and GND is DC 0 V when the sensor is unblocked (retracted position) and DC 5 V when the sensor is blocked. YES: Change Master Board. NO: Check sensor installation. Correct detecting plate. Check sensor connector for connection. Change sensor. 3 Fusing Pressure/Retraction Motor rotation when the Fusing Roller is pressed: the voltage across PJ14I-5A on Master Board and GND is DC 0 V when the motor is deenergized and DC 24 V when the motor is energized. NO: Change Master Board. 4 I/O check for Fusing Pressure Position Sensor when the Fusing Roller is pressed: the voltage across PJ6I-11B on Master Board and GND is DC 0 V when the sensor is unblocked and DC 5 V when the sensor is blocked (pressed position). YES: Change Master Board. NO: Check sensor installation. Correct detecting plate. Check sensor connector for connection. Change sensor. 5 I/O check for Fusing Retraction Position Sensor operation while the Fusing Pressure/ Retraction Motor is turning: the voltage across PJ17I-3B on Master Board and GND remains DC 0 V when the sensor is unblocked or remains DC 5 V when the sensor is blocked while the motor remains stationary, and alternates between DC 0 V when the sensor is unblocked and DC 5 V when the sensor is blocked while the motor is turning. YES: Change Master Board. NO: Check sensor installation. Correct detecting plate. Check sensor connector for connection. Change sensor. |
| Error code: | C0128 ... C0254 |
| Description: | CPU error (undefined trap) |
| Remedy: | Controller Board |
| Error code: | C0255 |
| Description: | CPU Error (NMI exception) |
| Error code: | C0256 |
| Description: | CPU Error (division by zero) |
| Error code: | C0257 |
| Description: | CPU Error (processing overflow) |
| Error code: | C0258 |
| Description: | CPU Error (break generated) |
| Error code: | C0800 |
| Description: | Image processing error |
| Causes: | The print sequence jam (J010x) was detected 2 times continuously. |
| Remedy: | 1 Checking the image data The image data is faulty. When this issue occurs only when handling the certain image data, check if the image data is faulty. 2 Checking the situation The printing operation of the certain file is faulty. Acquire the jobs log if the phenomenon can be reproduced by specifying the job when the error was detected.` 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. Detaching and reattaching the main PWB 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0998 |
| Description: | Shift transfer |
| Causes: | Controller Board. Video I/F Cable. Mechanical Control Board |
| Remedy: | 1 I/O check for Shifter Return Position Sensor operation: the voltage across PJ7A-7A on Control Board and GND is DC5V (sensor unblocked) and DC0V (sensor blocked). YES Change Control Board. NO Change sensor or Cabinet Transport Board. Change flat cable. 2 I/O check for Shifter Home Position Sensor operation: the voltage across PJ7A-8A on Control Board and GND is DC5V (sensor unblocked) and DC0V (sensor blocked). YES Change Control Board. NO Change sensor or Cabinet Transport Board. Change flat cable. |
| Error code: | C1000 |
| Description: | MP lift motor error |
| Causes: | The upper MP lift sensor (for upper limit detection) or lower MP lift sensor (for lower limit detection) does not detect turning on for 3s when the MP lift motor ascends or descends. |
| Remedy: | 1 Checking the lift base The lift base does not properly operate. If the lift base of the MP tray does not move up and down, repair or replace the lift base. 2 Checking the lift lever The lift lever is not properly attached. Check if the lift lever is located where it moves up and down by the lift motor cam or has no damage. Then, reattach the MP tray or replace the lift lever. 3 Checking the drive gear The drive gears for lifting up the lift base do not properly rotate. Check if the drive gears for lifting up the lift base can rotate smoothly or have no excessive load. Then, apply grease and repair the parts. 4 Checking the conveying unit The drawer connector connection between the conveying unit and the main unit is faulty. Firmly close the conveying unit. If there are foreign objects or the deformation on the drawer connector of the conveying unit for connecting to the main unit, repair them. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MP lift motor - Relay PWB • Relay PWB - Feed PWB Wiring diagram 6 Checking the MP lift motor The MP lift motor is faulty. Check the MP lift motor operation, and replace the motor if necessary. 7 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Upper or lower MP lift sensor - Relay PWB • Relay PWB - Feed PWB Wiring diagram 8 Checking the sensor The upper or lower MP lift sensor is not properly attached or faulty. Reattach the upper or lower MP lift sensor. If not repaired, replace the sensor. 9 Replacing the relay PWB The relay PWB is faulty. Replace the relay PWB. 10 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 11 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 12 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1001 |
| Description: | Standard RAM Error (no minimum stack area, etc.) |
| Remedy: | 1 C232 MAIN board is defective (Error related to board`s standard RAM.) Replace the board. |
| Error code: | C1002 |
| Description: | Standard RAM Error (less than standard size, etc.) |
| Causes: | • SDRAM • Controller (C495MAIN) |
| Remedy: | 1 C232 MAIN board is defective (Error related to board`s standard RAM.) Replace the board. |
| Error code: | C1020 |
| Description: | Lift motor 2 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1021 |
| Description: | RAM error (slot 1) |
| Causes: | Controller Board. Opt. RAM DIMM |
| Error code: | C1022 |
| Description: | RAM error (slot 2) |
| Remedy: | Opt. RAM DIMM |
| Error code: | C1400 |
| Description: | Rotary guide motor error Rotary guide sensor does not turn on. |
| Causes: | Poor contact in the connector terminals. Broken gear s or couplings of rotary guide motor. Defective rotary guide motor. Defective rotary guide sensor. Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector of the rotary guide motor and the connector YC2 on the main front PWB, and the continuity across the connector terminals. Repair or replace if necessary. Broken gears or couplings of rotary guide motor. Replace rotary guide motor. Defective rotary guide motor. Check for continuity across the coil. If none, replace rotary guide motor. Defective rotary guide sensor. Check if YC2-8 on the main front PWB goes low when rotary guide sensor is turned off. If not, replace rotary guide sensor. Poor contact in the connector terminals. Check the connection of connector of the rotary guide sensor and the connector YC2 on the main front PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Main front PWB or engine PWB and check for correct operation. |
| Error code: | C1700 |
| Description: | Built-in network hardware error |
| Error code: | C1720 |
| Description: | Network board uninstalled |
| Remedy: | Network Board |
| Error code: | C1999 |
| Description: | Other Hardware Error |
| Causes: | Controller Board |
| Error code: | C2000 |
| Description: | Drive motor problem Stable OFF is detected for 1 s continuously after drive motor stability. The drive motor is not stabilized in 6 s since the motor is activated. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective drive motor. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective drive motor. Replace the drive motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C999 |
| Description: | Engine flash ROM has no program data |
| Remedy: | Program DIMM |
| Error code: | E090 |
| Description: | Image data delay jam: Image data to be printed cannot be prepared. |
| Causes: | SYS board IMG board LGC board HDD Page memory |
| Remedy: | 1. Remove the paper remained in front of the registration sensor. 2. If the error still occurs, check the following: 3. Check if the error is cleared by turning the power OFF and then back ON. 4. Check if the connectors connecting the SYS board, SLG board and PLG board are disconnected. 5. Check if the connectors of the HDD are disconnected. 6. Check if the page memory is connected to the connector on the SYS board properly. 7. Replace the page memory. 8. Check if the harnesses connecting the SYS board, SLG board and PLG board are opencircuited. 9. Replace the HDD, SYS board, SLG board and PLG board. |
| Error code: | E091 |
| Description: | Other time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware. |
| Causes: | SYS board IMG board LGC board HDD |
| Remedy: | 1. Check if there is any paper in the equipment. Remove it if there is. 2. If the error still occurs, check the following: 3. Check if the error is cleared by turning the power OFF and then back ON. 4. Check if the connectors connecting the SYS board, SYSIF board, SLG board and PLG board are disconnected. 5. Check if the connectors of the HDD are disconnected. 6. Check if the page memory is connected to the connector on the SYS board properly. 7. Replace the page memory. 8. Check if the harnesses connecting the SYSIF board, SLG board and PLG board are opencircuited. 9. Replace the HDD, SYS board, SLG board and PLG board. |
| Error code: | E092 |
| Description: | Blown fuser fuse |
| Remedy: | 1 Check the connection status between the Fuser Unit and the MCU. [Fuser unit] - [HARNESS, MAIN] - [BOARD ASSY., MAIN C585 MCU] (CN109) 3 Replace the [Fuser unit]. 4 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E093 |
| Description: | Blown photoconductor unit fuse |
| Remedy: | 1 Check the connection status between the Photoconductor Unit and the MCU. [Photoconductor unit] - [ELECTRODE Assy., PC] - [HARNESS, MAIN] - [BOARD ASSY., MAIN C585 MCU] (CN108) 2 Replace the Photoconductor Unit. 3 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E094 |
| Description: | Transfer Roll Operating/Setting Error, or not installed. When the Secondary Transfer Sensor does not turn ON at separation of the Secondary Transfer Roller. |
| Causes: | • Primary Transfer Sensor (PC24) • Secondary Transfer Sensor (PC25) • Control Board (PWB-A) |
| Remedy: | 1 Check the operation of PC25. p113 PWB-A CNF1-A-3(ON) 3-G 2 Replace the PWB-A. |
| Error code: | E095 |
| Description: | HSYNC error |
| Remedy: | 1 Check the connection status between the LSU and the MCU. [Laser Scanner] - [HARNESS, LSU] - [BOARD ASSY., MAIN C585 MCU] (CN120) 2 Replace the [Laser Scanner]. 3 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E096 |
| Description: | Primary transfer roller pressing/separation error. When the Primary Transfer Sensor does not turn ON at separation of the Primary Transfer Roller. |
| Causes: | • Primary Transfer Sensor (PC24) • Secondary Transfer Sensor (PC25) • Control Board (PWB-A) |
| Remedy: | 1 Check the operation of PC25. p113 PWB-A CNF1-A-3(ON) 3-G 2 Replace the PWB-A. |
| Error code: | E111 |
| Description: | Laser malfunction (Magenta) - SOS signal is not detected within the lapse of a given period of time after staring the laser output. - SOS signal is not detected within a given period of time during printing or IDC sensor adjustment |
| Causes: | • PH Unit • PH Interface Board (PWB-D) • Mechanical Control Board (PWB-M) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. - - 2 Change PH Unit - - 3 Change PWB-D - - 4 Change PWB-M |
| Error code: | E112 |
| Description: | Laser malfunction (Yellow) - SOS signal is not detected within the lapse of a given period of time after staring the laser output. - SOS signal is not detected within a given period of time during printing or IDC sensor adjustment |
| Causes: | • PH Unit • PH Interface Board (PWB-D) • Mechanical Control Board (PWB-M) |
| Remedy: | 1 Check the connector for proper connection and correct as necessary. - - 2 Change PH Unit - - 3 Change PWB-D - - 4 Change PWB-M |
| Error code: | E113 |
| Display: | E113 error NVRAM |
| Description: | Parameters cannot be written. |
| Causes: | • PH Unit • PH Interface Board (PWB-D) • Mechanical Control Board (PWB-M) |
| Remedy: | (1) MAIN board assembly may be damaged. * Replace MAIN board assembly. |
| Error code: | E115 |
| Description: | Additional Cassette communication error - The communication between the MCU PWB and the Option Trays (STM, 3TM) cannot be made. |
| Causes: | • HARNESS ASSY 3TM/STM • PWB ASSY 3TM/STM • HARNESS ASSY R-BTM • MCU PWB |
| Remedy: | 1 Connection check of connectors 1.Make sure that the Connector (J541) of the HARNESS ASSY 3TM/STM is securely connected to the Connector of the PWB ASSY 3TM/STM. 2.Make sure that the Connector (J251) of the HARNESS ASSY 3TM/STM is securely connected to the Connector of the HARNESS ASSY RBTM. 3. Make sure that the Connector (J25) of the HARNESS ASSY R-BTM is securely connected to the Connector of the MCB PWB. Does the error occur? To Step 2 Problem solved 2 Continuity check of HARNESS ASSY 3TM/STM 1. Disconnect the relay connector P/ J251 of the HARNESS ASSY 3TM/ STM. 2. Disconnect the J541 of the PWB ASSY 3TM/STM. 3. Check if the following wiring have continuity. J251-1 . J541-10 J251-2 . J541-9 J251-4 . J541-7 J251-5 . J541-6 J251-6 . J541-5 Do all of the wiring have continuity? To Step 3 Replace the HARNESS ASSY 3TM/ STM 3 Continuity check of HARNESS ASSY R-BTM 1. Disconnect the relay connector P/ J251 of the PWB ASSY 3TM/STM. 2. Disconnect the J25 of the MCU PWB. 3. Check if the following wiring have continuity. P251-1 . J25-1 P251-2 . J25-2 P251-4 . J25-4 P251-5 . J25-5 P251-6 . J25-6 Do all of the wiring have continuity? Replace the PWB ASSY 3TM/STM / Replace the HARNESS ASSY RBTM |
| Error code: | E116 |
| Description: | Scanner motor error |
| Remedy: | 1 Check if the starting sound of the motor is audible. 2 Check the connection status between the LSU and the MCU. [Laser Scanner] (P204) - [HARNESS, LSU] - [BOARD ASSY., MAIN C585 MCU] (CN118) 3 Replace the [Laser Scanner]. 4 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E123 |
| Description: | Problem in F8 mode. C02 was done wrong |
| Remedy: | 1 Check if the NIP lever is used at the position for envelopes. 2 Check the Fuser Unit for the followings. Check if paper is jammed at the Fuser. Check the fuser roller for any scratch or foreign material. Rotate the green knob on the backside of the fuser unit in order to check if the spur gear 19 and heat roller turn smoothly. 3 Replace the [Fuser unit]. 4 Replace the [POWER SUPPLY]. 5 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E124 |
| Description: | Scan drive problem |
| Remedy: | 1 Check if the NIP lever is used at the position for envelopes. 2 Check the Fuser Unit for the followings. Check if paper is jammed at the Fuser. Check the fuser roller for any scratch or foreign material. Rotate the green knob on the backside of the fuser unit in order to check if the spur gear 19 and heat roller turn smoothly. 3 Replace the [Fuser unit]. 4 Replace the [POWER SUPPLY]. 5 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E125 |
| Description: | Abnormally low temperature 2 |
| Remedy: | 1 Check if the NIP lever is used at the position for envelopes. 2 Check the Fuser Unit for the followings. Check if paper is jammed at the Fuser. Check the fuser roller for any scratch or foreign material. Rotate the green knob on the backside of the fuser unit in order to check if the spur gear 19 and heat roller turn smoothly. 3 Replace the [Fuser unit]. 4 Replace the [POWER SUPPLY]. 5 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E126 |
| Description: | Abnormally low temperature 1 |
| Remedy: | 1 Check if the NIP lever is used at the position for envelopes. 2 Check the Fuser Unit for the followings. Check if paper is jammed at the Fuser. Check the fuser roller for any scratch or foreign material. Rotate the green knob on the backside of the fuser unit in order to check if the spur gear 19 and heat roller turn smoothly. 3 Replace the [Fuser unit]. 4 Replace the [POWER SUPPLY]. 5 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E132 |
| Description: | Auto exposure problem |
| Remedy: | 1 Check the FRAM Board for the connection status. Check if the connector is securely connected. 2 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E144 |
| Description: | Mirror sensor, fuse 303 on DC board |
| Causes: | • TRAY FEED/LIFT MOTOR • HARNESS ASSY 3TM • ACTUATOR SNR • TRAY LEVEL SENSOR • HARNESS ASSY SNR • PWB ASSY 3TM |
| Remedy: | 1 TRAY FEED/LIFT MOTOR installation check Are TRAY FEED/LIFT MOTOR and GEAR 29 installed correctly? To Step 2 Remove and reinstall the failing part. 2 Operation check of the TRAY FEED/ LIFT MOTOR 1. Make sure that the TRAY FEED/ LIFT MOTOR operates properly. 2. Check the rotation of each gear. Do TRAY FEED/LIFT MOTOR and each gear rotate properly? To Step 3 Replace the TRAY FEED/ LIFT MOTOR 3 Check of ACTUATOR SNR for damage Check the ACUATOR SNR for bending or damage. Is the ACTUATOR SNR installed correctly? To Step 4 Remove and reinstall the failing part. 4 Continuity check of HARNESS ASSY SNR 1. Disconnect the relay connector P674/J617 of the HARNESS ASSY SNR. 2. Disconnect the J205 of the TRAY FEED/LIFT MOTOR. 3. Check if the following wiring have continuity. J617-6 . J205-1 J617-5 . J205-2 J617-4 . J205-3 J617-3 . J205-4 J617-2 . J205-5 J617-1 . J205-6 Do all of the wiring have continuity? To Step 5 Replace the HARNESS ASSY SNR 5 Continuity check of HARNESS ASSY 3TM 1. Disconnect the J549A of the PWB ASSY 3TM. 2. Disconnect the relay connector P674/J617 of the HARNESS ASSY 3TM. 3. Check if the following wiring have continuity. J549A-6 . P674-7 J549A-5 . P674-8 J549A-4 . P674-9 J549A-3 . P674-10 J549A-2 . P674-11 J549A-1 . P674-12 Do all of the wiring have continuity? To Step 6 Replace the HARNESS ASSY 3TM 6 Installation check of TRAY LEVEL SENSOR Check the installation of the TRAY LEVEL SENSOR. Is the TRAY LEVEL SENSOR installed correctly? To Step 7 Remove and reinstall the TRAY LEVEL SENSOR. 7 Continuity check of HARNESS ASSY SNR 1. Disconnect the relay connector P674/J617 of the HARNESS ASSY SNR. 2. Disconnect the J108 of the TRAY LEVEL SENSOR. 3. Check if the following wiring have continuity. J617-12 . J108-1 J617-11 . J108-2 J617-10 . J108-3 Do all of the wiring have continuity? To Step 8 Replace the HARNESS ASSY SNR 8 Continuity check of HARNESS ASSY 3TM 1. Disconnect the J549A of the PWB ASSY 3TM. 2. Disconnect the relay connector P674/J617 of the HARNESS ASSY 3TM. 3. Check if the following wiring have continuity. J549A-12 . P674-1 J549A-11 . P674-2 J549A-10 . P674-3 Do all of the wiring have continuity? To Step 9 Replace the HARNESS ASSY 3TM 9 Check of TRAY LEVEL SENSOR 1. Replace the TRAY LEVEL SENSOR. 2. Turn the main power on. Does the error occur? Replace the PWB ASSY 3TM Problem solved |
| Error code: | E153 |
| Description: | Ozone fan error |
| Remedy: | 1 Check the connection status between the Fan and the MCU. [FAN, PC] - [HARNESS, PAPER LOAD] - [BOARD ASSY., MAIN C585 MCU] (CN114) 2 Replace the [FAN, PC]. 3 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E154 |
| Description: | Toner fan error |
| Remedy: | 1 Check the connection status between the Fan and the MCU. [FAN, DUST CHAMBER] - [HARNESS, MAIN] - [BOARD ASSY., MAIN C585 MCU] (CN107) 2 Replace the [FAN, DUST CHAMBER]. 3 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E155 |
| Description: | Fuser fan error |
| Remedy: | 1 Check the connection status between the Fan and the MCU. [FAN, FU] - [BOARD ASSY., MAIN C585 MCU] (CN106) 2 Replace the [FAN, FU]. 3 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E156 |
| Description: | Power supply fan error |
| Remedy: | 1 Check the connection status between the Fan and the MCU. [FAN, LPS] - [HARNESS, MAIN] - [BOARD ASSY., MAIN C585 MCU] (CN107) 2 Replace the [FAN, LPS]. 3 Replace the [BOARD ASSY., MAIN C585 MCU]. |
| Error code: | E256 |
| Description: | Transfer Belt unit lever out-of-position |
| Remedy: | 1 Check if the photoconductor lock lever is set to printing position. 2 Check the connection status between the sensor and the MCU. [TRANSFER UNIT, Assy., ASP] - [HARNESS, MAIN] - [BOARD ASSY., MAIN C585 MCU] (CN110) 3 Check the flag for detecting VSYNC (convex portion) on the extreme right of the Transfer Belt for any abnormality. 4 Replace the [TRANSFER UNIT, Assy., ASP]. 5 Check the connection status between the Motor and the MCU. [SERVOMOTOR, PC] - [HARNESS, MAIN] - [BOARD ASSY., MAIN C585 MCU] (CN105) 6 Replace the [SERVOMOTOR, PC]. |
| Error code: | E998 |
| Description: | Engine communication error Communication between Main Board Assy and MCU Board Assy has abnormality. |
| Causes: | The firmware of the engine controller is faulty. The Main Board Assy. is faulty. |
| Remedy: | 1. Any other electric appliances; generators, radiotransmitter, etc., within three meters from the printer? In such a case, noises from them may cause an error in reading/writing; therefore, change the location of them or turn them off. 2. Connection between Main Board Assy and MCU Board Assy correct? 3. Replace Main Board Assy. 4. Replace MCU Board Assy. |
Парткод
Название
EPSON 0226 Тонер-картридж желтый
EPSON 0227 Тонер-картридж пурпурный
EPSON 0228 Тонер-картридж голубой
EPSON 0229 Тонер-картридж черный
EPSON Коллектор обработанного тонера
EPSON 0289 Набор цветных тонер-картриджей CMY
EPSON 1107 Блок фотобарабана
EPSON Блок термозакрепления (печка)
EPSON 0230 Тонер-картридж желтый
EPSON 0231 Тонер-картридж пурпурный
EPSON 0232 Тонер-картридж желтый
