Epson AcuLaser C4100

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

100000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Число страниц в месяц	100 000
Область применения	большой офис
Тип	лазерный/светодиодный
Технология печати	лазерная
Размещение	настольный
Макс. формат	A4
Цветность печати	цветная
Тип устройства	Принтер
Печать фотографий
Телефон
Факс
Сканер
Копир
Принтер
Печать без полей
Прямая печать
Двусторонняя печать
Время разогрева	30
Макс, разрешение для ч/б печати
По X	600
По Y	600
Скорость ч/б печати
A4	24
Время выхода первого отпечатка
Ч/б	13
Цветн,	13
Расходные материалы
Ресурс цветного картриджа/тонера	8 000
Ресурс фотобарабана	30 000
Количество картриджей	4
Ресурс ч/б картриджа/тонера	10 000
Печать на:
Рулоне
CD/DVD
Матовой бумаге
Конвертах
Пленках
Карточках
Этикетках
Глянцевой бумаге
Фотобумаге
Плотность бумаги
Минимальная	60
Максимальная	216
Телефон
Спикерфон
Проводная трубка
Беспроводная трубка
АОН
Caller ID
Автоответчик
Стандарт DECT
Языки управления
PostScript 3
PDF
PostScript 2
PCL 5c
PPDS
PCL 6
PCL 5e
PostScript	опционально
Подача бумаги
Максимальная	1 600
Стандартная	600
Финишер
Степлер
Брошюровщик
Сортер
Сортировка со сдвигом
Интерфейсы
Версия USB	2,0
RS-232
FireWire (IEEE 1394)
Wi-Fi
Bluetooth
Устройство для чтения карт памяти
Инфракрасный порт
Веб-интерфейс
USB
LPT
Ethernet (RJ-45)
Память/Процессор
Процессор	RISC
Объем памяти	64
Макс, объем памяти	1 024
Частота процессора	400
Дополнительная информация
Мин. системные требования
Поддержка ОС
Linux
Windows
Mac OS
DOS
Потребляемая мощность
В режиме ожидания	180
При работе	600
Уровень шума
При работе	55
В режиме ожидания	48
Габариты
Высота	445
Глубина	638
Ширина	439
Вес	35

Модули

MECH-015 (12.2)

MECH-017 (13.1)

MECH-002 (03.1)

ELEC-001 (16.1)

MECH-004 (04.01)

CASE-001 (01.1)

MECH-016 (12.3)

MECH-007 (05.1)

MECH-001 (02.1)

MECH-006 (04.3)

MECH-020 (15.2)

MECH-013 (11.1)

MECH-010 (08.1)

MECH-011 (09.1)

MECH-009 (07.1)

MECH-019 (15.1)

MECH-005 (04.02)

MECH-008 (06.1)

MECH-014 (12.1)

MECH-018 (14.1)

MECH-012 (10.1)

Детали

Деталь:	KIT HOLDER ASSY TONER(Y)
Парткод:	2085216

Деталь:	KIT HOLDER ASSY TONER(M)
Парткод:	2085217

Деталь:	KIT HOLDER ASSY TONER(C)
Парткод:	2085218

Деталь:	KIT HOLDER ASSY TONER(K)
Парткод:	2085219

Деталь:	SENSOR TONER LOW
Парткод:	2085220

Деталь:	BRACKET LEVER
Парткод:	1112454

Деталь:	LEVER DRUM
Парткод:	1112455

Деталь:	SPRING LEVER 30N
Парткод:	1112456

Деталь:	ACTUATOR I/L
Парткод:	1112457

Деталь:	GEAR IDL PRESS
Парткод:	1112459

Деталь:	GEAR ASSY PR R
Парткод:	1112460

Деталь:	FILM REGI
Парткод:	1112461

Деталь:	PWBA ASSY EARTH
Парткод:	2071868

Деталь:	GEAR ASSY PR L
Парткод:	1112462

Деталь:	CHASSIS MAIN
Парткод:	1265573

Деталь:	CHUTE RETADE
Парткод:	1110098

Деталь:	ROLL ASSY
Парткод:	1110099

Деталь:	HOLDER RETARD
Парткод:	1290235

Деталь:	SPRING RETARD
Парткод:	1290236

Деталь:	GUIDE L ESS
Парткод:	1112466

Деталь:	GUIDE R ESS
Парткод:	1112467

Деталь:	BOARD ASSY,MAIN
Парткод:	2089853

Деталь:	BOARD ASSY.,MEMORY
Парткод:	2088339

Деталь:	COVER FDR FRONT
Парткод:	1110105

Деталь:	COVER CASSETTE REAR
Парткод:	1265600

Деталь:	BLOCK
Парткод:	1110107

Деталь:	CHUTE ASSY TURN
Парткод:	1110108

Деталь:	CONTROL PANEL
Парткод:	2085361

Деталь:	COVER ASSY FRONT HEAD
Парткод:	2091083

Деталь:	COVER FRONT HEAD
Парткод:	1110076

Деталь:	FAN FUSER
Парткод:	2085193

Деталь:	CVR TOP STOPPER
Парткод:	1110078

Деталь:	COVER TOP
Парткод:	1110079

Деталь:	COVER ASSY TOP MAIN
Парткод:	1289192

Деталь:	LATCH TOP R
Парткод:	1110082

Деталь:	LATCH TOP L
Парткод:	1265592

Деталь:	COVER REAR
Парткод:	1110084

Деталь:	KIT COVER ASSY TOP
Парткод:	1110077

Деталь:	KIT COVER ASSY TOP PHD
Парткод:	1265593

Деталь:	PLATE ASSY DISPENSER
Парткод:	2085221

Деталь:	BOX ASSY CRUM READER
Парткод:	2085319

Деталь:	HARNESS ASSY CRUM
Парткод:	2071867

Деталь:	RACK V
Парткод:	1112451

Деталь:	GEAR SLIDE
Парткод:	1112452

Деталь:	RACK H
Парткод:	1112453

Деталь:	HOUSING ASSY RETARD
Парткод:	2085198

Деталь:	ROLL TURN
Парткод:	1111860

Деталь:	ROLL ASSY RETARD
Парткод:	1111861

Деталь:	CLUTCH TURN MSI
Парткод:	2085199

Деталь:	STRAP
Парткод:	1110097

Деталь:	PICK UP ASSY
Парткод:	2071887

Деталь:	ROLL ASSY FEED
Парткод:	1110119

Деталь:	EXIT SENSOR
Парткод:	2026720

Деталь:	ACTUATOR LINK
Парткод:	1021488

Деталь:	SOLENOID FEED TRAY 1
Парткод:	2071888

Деталь:	CLUTCH ASSY TURN TRAY 1
Парткод:	1110121

Деталь:	ROLL ASSY TURN
Парткод:	1110122

Деталь:	ROLL ASSY
Парткод:	1110099

Деталь:	HARNESS ASSY FEEDER
Парткод:	2071860

Деталь:	HARNESS ASSY LVNC3
Парткод:	2085229

Деталь:	HARNESS ASSY DRV 1
Парткод:	2071877

Деталь:	HARNESS ASSY DRV 2.2
Парткод:	2086086

Деталь:	HARNESS ASSY LVRPG
Парткод:	2071879

Деталь:	HARNESS ASSY ROS KA2
Парткод:	2085232

Деталь:	HARNESS ASSY 24V
Парткод:	2071881

Деталь:	HARNESS ASSY FRONT 1
Парткод:	2071882

Деталь:	HARNESS ASSY OPF MAIN
Парткод:	2071883

Деталь:	HARNESS ASSY OPSEA
Парткод:	2085234

Деталь:	HARNESS ASSY EEPROM
Парткод:	2071885

Деталь:	HARNESS ASSY TMPNCS
Парткод:	2085235

Деталь:	ROS ASSY
Парткод:	2085214

Деталь:	HSG ASSY BIAS
Парткод:	1112434

Деталь:	STUD PLUNGER
Парткод:	1112438

Деталь:	KIT HSG ASSY BIAS
Парткод:	1112431

Деталь:	CHUTE ASSY EXIT
Парткод:	1265628

Деталь:	ROLL EXIT
Парткод:	1111876

Деталь:	ROLL MID
Парткод:	1111877

Деталь:	MOTOR ASSY DUP
Парткод:	2085398

Деталь:	KIT GLOMET
Парткод:	1267092

Деталь:	FUSER ASSY (220V)
Парткод:	2085468

Деталь:	HARNESS ASSY FRONT 2
Парткод:	2071861

Деталь:	HARNESS ASSY OPEPANE BS
Парткод:	2071862

Деталь:	E.R.M. SENSOR
Парткод:	2021773

Деталь:	ACTUATOR FULL STACK
Парткод:	1111867

Деталь:	ROLL DUP
Парткод:	1111866

Деталь:	ACTUATOR DUP
Парткод:	1111868

Деталь:	HARNESS ASSY DUP 2
Парткод:	2085207

Деталь:	ROLL ASSY FEED
Парткод:	1111869

Деталь:	ACTUATOR MSI
Парткод:	1111870

Деталь:	SOLENOID FEED MSI
Парткод:	1111871

Деталь:	WIRE ASSY DUP EARTH
Парткод:	2072713

Деталь:	KIT ROLL PINCH EXIT
Парткод:	1265606

Деталь:	KIT ROLL PINCH
Парткод:	1265607

Деталь:	PWBA MCU CPU HBN STD
Парткод:	2089815

Деталь:	FAN REAR
Парткод:	2071870

Деталь:	CLAMP GUIDE HARNESS
Парткод:	2071871

Деталь:	LVPS
Парткод:	2087623

Деталь:	HARNESS ASSY AC SW
Парткод:	2071874

Деталь:	PWBA DRV HBN
Парткод:	2085228

Деталь:	HOUSING FDR L
Парткод:	1279590

Деталь:	HOUSING FDR R
Парткод:	1279591

Деталь:	HARNESS ASSY TMPA
Парткод:	2071858

Деталь:	ENVIRONMENT SENSOR
Парткод:	2061097

Деталь:	FOOT
Парткод:	1231706

Деталь:	STOPPER CST
Парткод:	1110111

Деталь:	SWITCH SIZE TRAY 1
Парткод:	1110112

Деталь:	HARNESS ASSY OPFREC
Парткод:	2071859

Деталь:	LEVER LOW PAPER
Парткод:	1110113

Деталь:	INDICATOR
Парткод:	1110115

Деталь:	CHUTE ASSY IN
Парткод:	2085201

Деталь:	WIRE ASSY BTR 2
Парткод:	2072702

Деталь:	WIRE ASSY DTSK
Парткод:	2072703

Деталь:	HARNESS ASSY FSR3C
Парткод:	2085203

Деталь:	HARNESS ASSY CTD
Парткод:	2072706

Деталь:	SENSOR ASSY ADC
Парткод:	2072707

Деталь:	WASTE TONER SENSOR
Парткод:	2028242

Деталь:	HARNESS ASSY TFLSNS
Парткод:	2072708

Деталь:	DRIVE ASSY FUSER
Парткод:	2085205

Деталь:	WIRE ASSY FSR EARTH
Парткод:	2072710

Деталь:	LATCH R
Парткод:	1111862

Деталь:	LATCH L
Парткод:	1111863

Деталь:	KIT ROLL PINCH TURN
Парткод:	1111864

Деталь:	KIT ROLL PINCH DUP
Парткод:	1111865

Деталь:	HRANESS ASSY TNR4SE
Парткод:	2085215

Деталь:	PWB EEPROM
Парткод:	2071865

Деталь:	HVPS SUB
Парткод:	2071866

Деталь:	DRIVE ASSY DEVE
Парткод:	2085222

Деталь:	DRIVE ASSY MAIN
Парткод:	2085223

Деталь:	CHUTE ASSY REGI
Парткод:	2085209

Деталь:	CLUTCH REGI
Парткод:	2085210

Деталь:	E.R.M. SENSOR
Парткод:	2021773

Деталь:	ACTUATOR REGI
Парткод:	1112416

Деталь:	HOUSING ASSY
Парткод:	1112417

Коды ошибок

0017 ... 0800

0998, 0999

100

1002

101

1010

102

1020, 1021

103

104

105

106

107

1100, 1101

1120 ... 1123

1180, 1185

1200, 1210

1400

1500

1550

1600

1700

1800

1999

2000

998

Описание

Парткод

Название

EPSON Тонер-картридж голубой

EPSON Тонер-картридж пурпурный

EPSON Тонер-картридж желтый

EPSON Тонер-картридж черный

EPSON Блок фотобарабана

EPSON Блок перноса изображения

EPSON Блок термозакрепления (печка)

Error code:	0017 ... 0800
Description:	0017 CPU error (Interrupt exception) 0088 CPU error (System call exception) 0089 CPU error (Break point exception) 0091 CPU error (Disabled floating-point exception) 0300 CPU error (Reserved (undefined) exception) 0301 CPU error (Machine check exception) 0302 CPU error (Data access exception) 0303 CPU error (Instruction access exception) 0304 CPU error (Alignment exception) 0305 CPU error (Program exception) 0306 CPU error (Trace exception) 0307 CPU error (Performance monitor exception) 0308 CPU error (System administration interrupt exception) 0309 CPU error (Temperature management interrupt exception) 0800 IPL error (Controller defective)
Remedy:	1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. • Reinsert the DIMM. Replace or reinstall the relevant part. Go to step 2. 2 Improving the CONTROLLER PWB Environment: • Update the program to the latest one in the DIMM.ÅB Replace or reinstall the relevant part. Go to step 3. 3 Replacing the CONTROLLER PWB and Performing Checks: Does the problem still occur after replacing the MCU PWB with a normal one? - Problem solved.

Error code:	100
Description:	A fault has occurred
Causes:	• ROS ASSY • PWBA MCU
Remedy:	1 Make sure all packing material is removed from the printer. The detensioner is located underneath the toner cartridges. Make sure the ITU Detensioner is removed. Remove the Detensioner by pulling up on the red handle on the right side of the ITU. Note: All the print cartridges must be removed to gain access to the Detensioner packing material. Has all packing material been removed from the printer? Go to step 2 Remove any remaining packing material from the printer 2 Check the ITU Release Lever for correct operation. The ITU Release Lever is the black lever located on the left upper side frame above the ITU opening and can be seen by opening and lowering the MPF Assembly. When locked the lever should be at the 6 o`clock position. When unlocked it should be in a 3 o`clock position. Undue pressure is not required to operate the lever. Does the ITU release lever operate correctly? Go to step 3 Repair as necessary 3 Check the second transfer roll installation. Is it installed correctly? Go to step 4 Reinstall the second transfer roll. 4 Check the display error log in the Diagnostic Menu. Is 100 ITU preceded in the log by a 104 ITU Error? Go to “104 ITU Error”. Go to step 5 5 Remove the ITU assembly and check that the sensor cable is seated in the handle of the ITU assembly correctly. Note: The sensor connector is located on the side of the ITU handle assembly. Is the cable seated correctly? Go to step 6 Reinstall the cable correctly. Check again for a 100 ITU Error. If 100 ITU Error is displayed, go to step 6 6 The front contamination shield is attached to the font plate of the ITU frame and lies on the top of the ITU belt. Is the front contamination shield lying on the belt? Go to step 7 Position the shield on top of the belt. 7 Make sure the ITU Cleaner Gear (A) is turning. Observe the gear by opening the front Paper Jam Door above the integrated paper tray 1. Observe the white cleaner gear during POR. The gear should turn slowly and smoothly for approximately 8 seconds before the printer displays a 100 ITU error. Is the ITU Cleaner Gear turning? Go to step 11 Go to step 8 8 Check to see if the ITU Drive Roll Gear (A) is turning during POR. Observe the gear by opening the MFP door to its horizontal position. Observe the gear on the left end of the ITU Drive Roll. The ITU Drive Roll Gear should turn for a few seconds slowly and smoothly before the printer posts a 100 ITU error. Does the Gear turn? Go to step 10 Go to step 9 9 Check to see if the ITU Drive Motor is turning during POR. Observe the ITU Motor during POR by removing the Rear Cover. Is the ITU Drive Motor turning? Replace the “ITU drive assembly” Go to step 10 10 Check the printer is setting on a solid flat surface. Is the printer setting on a solid flat surface? Go to step 11 Place the printer on a solid flat surface. 11 Make sure the ITU drive motor assembly cable is correctly installed to the ITU drive motor and at connector location J64 on the system board. Is the cable correctly installed? Go to step 12 Install the cable correctly 12 Make sure the ITU Autoconnect Cable is installed correctly at connector location J72 on the system board. Is the cable correctly installed? Go to step 13 Install the connector/cable correctly 13 Make sure the ITU Autoconnect connector in the printer is seated correctly in the connector plate. Is the connector seated correctly? Replace the following FRUs in the following order: 1. “ITU assembly”. 2. “System board”. Replace the ITU Autoconnect cable.

Error code:	101
Description:	Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable.
Causes:	• Long-Life Maintenance Kit, 650-4360-00
Remedy:	1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts.

Error code:	1010
Display:	Problem with Printhead L/R Chk printing results
Description:	Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively.
Causes:	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB.
Remedy:	Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Error code:	102
Display:	Service Call 102: Error
Description:	Environmental Sensor Failure An error was detected in the Environmental Sensor circuitry.
Causes:	• Temp/Humidity Sensor, PL9.1.20 • TMP Harness, PL10.1.4
Remedy:	1 Test the Temperature/Humidity Sensor. Run the Service Diagnostics Temperature/ Humidity Sensor test. Does the sensor function correctly? Go to Step 2. Replace the Temp/ Hum Sensor. 2 Check the Humidity signal. Disconnect P/J231. Is the voltage across P/J231-2 <=> P/J231-3 less than +3 V and above +0.5 V. Go to Step 4. Go to Step 3. 3 Check the Temperature signal. Disconnect P/J231. Is the voltage across P/J231-4 <=> P/J231-3 greater than +2.5 V? Go to Step 4. Replace the Engine Control Board. 4 Check for +5 V to the Temperature/ Humidity Sensor. Disconnect P/J231. Is there +5 V across P/J231-1 <=> P/J231-3? Replace the Temp/ Hum Sensor. Replace the Engine Control Board.

Error code:	103
Display:	Service Call 103: Error
Description:	Fuser Motor Failure The Fuser Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Fuser Drive Assembly, PL5.2.25 • TNRFULL/FSR Harness, PL5.2.30 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.1
Remedy:	1 Check the Fuser Drive Assembly for damage. Are any parts of the Fuser Drive Assembly damaged or excessively worn? Replace the Fuser Drive Assembly. Go to Step 2. 2 Check the Fuser Motor connection. Is P/J521 connected to the harness? Go to Step 3. Reconnect the Fuser Motor. 3 Test the Fuser Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Fuser Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Fuser Motor. Is the +24 V across P/J521-10 <=> P/J 521-8? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the TNRFULL/FSR Harness PL5.2.30 for continuity. 1. Disconnect P/J52 and P/J521. 2. Check continuity between J52 <=> J521. Replace the Engine Control Board. Replace the FSR/ ADC Harness.

Error code:	104
Display:	Service Call 104: Error
Description:	Developer Motor Failure The Developer Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Developer Drive Assembly, PL8.1.1 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Developer Drive Assembly for damage. Are any parts of the Developer Drive Assembly damaged or excessively worn? Replace the Developer Drive Assy. Go to Step 2. 2 Check the Developer Motor connection. Is P/J491 connected to the harness? Go to Step 3. Reconnect the Developer Motor. 3 Test the Developer Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Developer Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Developer Motor. Is the +24 V across P/J491-1 <=> P/J 481-5? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J491. 2. Check continuity between J48 <=> J491. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.

Error code:	105
Display:	Service Call 105: Error
Description:	Main Motor Failure The Main Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Main Drive Assembly, PL8.1.2 • Engine Control Board, PL9.1.16 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Main Drive Assembly for damage. Are any parts damaged? Replace the Main Drive Assembly. Go to Step 2. 2 Check the Main Motor connection. Is P/J481 connected to the harness? Go to Step 3. Reconnect the Main Motor. 3 Test the Main Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Main Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Main Motor. Is there +24 V across P/J481-10 <=> P/J 481-8? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness, PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.

Error code:	106
Display:	Service Call 106: Error
Description:	Motor Failure One of the primary drive motors has failed.
Causes:	• Main Drive Assembly, PL8.1.2 • Developer Drive Assembly, PL8.1.1 • Fuser Drive Assembly, PL5.2.25 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11
Remedy:	1 Check the motors. Run the Service Diagnostics motor tests to determine the failed part. Is the failed part the Main Drive Motor? Go to. Test the Fuser Motor. 2 Is the failed part the Fuser Drive Motor? Go to. Test the Developer Motor. 3 Is the failed part the Developer Drive Motor? Go to. Replace the Engine Control Board.

Error code:	107
Display:	Service Call 107: Error
Description:	Printhead Error
Causes:	Does error reoccur? Is error recovered by reloading PU F/W?
Remedy:	Magenta printhead lost Hsync Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J11 and J12 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”.

Error code:	998
Description:	Tray Elevator Motor Error
Causes:	• Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective
Remedy:	1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply.