Epson AcuLaser C4200DNPC5

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

90000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Факс
Печать фотографий
Телефон
Копир
Сканер
Тип устройства	Принтер
Макс. формат	A4
Цветность печати	цветная
Размещение	настольный
Технология печати	лазерная
Тип	лазерный/светодиодный
Число страниц в месяц	90 000
Область применения	средний офис
Принтер
Прямая печать
Пигментные чернила
Печать без полей
Двусторонняя печать
Количество цветов	4
Макс, разрешение для ч/б печати
По X	600
По Y	600
По Y	1 200
По X	1 200
Скорость ч/б печати
A4	35
A4	25
Время выхода первого отпечатка
Цветн,	12,5
Ч/б	10,2
Сканер
Стандарт WIA
Стандарт TWAIN
Отправка изображения по e-mail
Расходные материалы
Ресурс ч/б картриджа/тонера	10 000
Количество картриджей	4
Ресурс фотобарабана	35 000
Ресурс цветного картриджа/тонера	8 500
Печать на:
Конвертах
Карточках
Пленках
Этикетках
Глянцевой бумаге
Матовой бумаге
Фотобумаге
CD/DVD
Рулоне
Плотность бумаги
Минимальная	60
Максимальная	216
Факс
Цветной
Телефон
Стандарт DECT
Проводная трубка
Беспроводная трубка
АОН
Caller ID
Автоответчик
Спикерфон
Шрифты и языки управления
Языки управления
PostScript 3
PCL 5c
PostScript
PPDS
PCL 5e
PostScript 2
PDF
PCL 6
Количество установленных шрифтов
PCL	93
PostScript	17
Подача бумаги
Стандартная	700
Финишер
Сортировка со сдвигом
Брошюровщик
Степлер
Электронная сортировка
Сортер
Интерфейсы
LPT
USB
Веб-интерфейс
Ethernet (RJ-45)
Устройство для чтения карт памяти
Bluetooth
Wi-Fi
RS-232
Инфракрасный порт
FireWire (IEEE 1394)
Версия USB	2,0
Память/Процессор
Частота процессора	600
Макс, объем памяти	640
Объем памяти	128
Процессор	PowerPC
Дополнительная информация
Мин. системные требования	Intel Pentium II
Поддержка ОС
Windows
DOS
Mac OS
Linux
Потребляемая мощность
В режиме ожидания	35
При работе	960
Уровень шума
В режиме ожидания	35
При работе	55
Габариты
Высота	457
Ширина	437
Глубина	588
Вес	34,5

Модули

MECH-015

MECH-008

MECH-010

MECH-002

MECH-012

MECH-0052

MECH-014

MECH-0092

MECH-011

MECH-006

MECH-004

CASE-001

MECH-007

MECH-003

MECH-013

ELEC-001

MECH-001

MECH-016

Детали MECH-008

Деталь:	STRAP
Парткод:	1409146

Деталь:	CHUTE ASSY DUP IN
Парткод:	2103371

Деталь:	LATCH L
Парткод:	1411376

Деталь:	HOLDER ASSY CTD
Парткод:	2103373

Деталь:	SENSOR TNR FULL
Парткод:	2103374

Деталь:	DRIVE ASSY FUSER
Парткод:	2103375

Деталь:	WIRE ASSY FSR EARTH
Парткод:	2104493

Деталь:	LATCH R
Парткод:	1411377

Деталь:	HARNESS ASSY FSR/ADC
Парткод:	2104494

Деталь:	HARNESS ASSY TNRFULL/FSR
Парткод:	2104495

Деталь:	KIT ROLL PINCH DUP
Парткод:	1411378

Деталь:	KIT ROLL PINCH TURN
Парткод:	1411379

Деталь:	KIT MSI SE
Парткод:	2108054

Деталь:	SOLENOID FEED MSI
Парткод:	2103377

Деталь:	SENSOR UPPER PASS
Парткод:	2091186

Деталь:	ACTUATOR NO PAPER MSI
Парткод:	1409147

Деталь:	ROLL ASSY FEED
Парткод:	1409148

Деталь:	HARNESS ASSY OPEPANE SE
Парткод:	2104996

Деталь:	HARNESS ASSY FRONT/DUP
Парткод:	2104496

Деталь:	WIRE ASSY DUP EARTH
Парткод:	2104497

Деталь:	FAN FRONT
Парткод:	2103378

Деталь:	PLATE EARTH OUT3
Парткод:	1411381

Деталь:	ACTUATOR FULL STACK
Парткод:	1409149

Деталь:	MOTOR ASSY DUP 17PM
Парткод:	2103379

Деталь:	ACTUATOR DUP
Парткод:	1111868

Деталь:	ROLL DUP
Парткод:	1409150

Деталь:	ROLL EXIT
Парткод:	1409151

Деталь:	KIT ROLL PINCH EXIT
Парткод:	2104498

Коды ошибок

0017 ... 0258

0800 ... 1021

100

101

102

103

104

105

106

107

1120 ... 2000

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

Error code:	0017 ... 0258
Description:	0017 CPU error (undefined interruption) 0081 CPU error (TLB modification exception) 0082 CPU error (TLB miss exception [Load/Fetch]) 0083 CPU error (TLB miss exception [Store]) 0084 CPU error (address error exception [Load/Fetch]) 0085 CPU error (address error exception [Store]) 0086 CPU error (bus error exception [Fetch]) 0087 CPU error (bus error exception [Load/Store]) 0088 CPU error (SYSCALL exception) 0089 CPU error (Break exception) 0090 CPU error (reserving command exception) 0091 CPU error (unused coprocessor exception) 0092 CPU error (FPU exception) 0093 CPU error (TLB exception) 0094 CPU error (XTLB exception) 0095 CPU error (cache exception) 0096 CPU error (Trap exception) 0097 CPU error (FPU exception) 0098 CPU error (watch exception) 0128 ~ 0254 CPU error (undefined trap) 0255 CPU error (NMI exception) 0256 CPU error (divide by 0) 0257 CPU error (arithmetic overflow) 0258 CPU error (break occurrence)
Remedy:	Turn off the power to the printer once and turn it on again and check to see if the same error occurs again. If it occurs again, replace the Main Controller with a new one.

Error code:	100
Description:	A fault has occurred
Causes:	• ROS ASSY • PWBA MCU
Remedy:	1 Make sure all packing material is removed from the printer. The detensioner is located underneath the toner cartridges. Make sure the ITU Detensioner is removed. Remove the Detensioner by pulling up on the red handle on the right side of the ITU. Note: All the print cartridges must be removed to gain access to the Detensioner packing material. Has all packing material been removed from the printer? Go to step 2 Remove any remaining packing material from the printer 2 Check the ITU Release Lever for correct operation. The ITU Release Lever is the black lever located on the left upper side frame above the ITU opening and can be seen by opening and lowering the MPF Assembly. When locked the lever should be at the 6 o`clock position. When unlocked it should be in a 3 o`clock position. Undue pressure is not required to operate the lever. Does the ITU release lever operate correctly? Go to step 3 Repair as necessary 3 Check the second transfer roll installation. Is it installed correctly? Go to step 4 Reinstall the second transfer roll. 4 Check the display error log in the Diagnostic Menu. Is 100 ITU preceded in the log by a 104 ITU Error? Go to “104 ITU Error”. Go to step 5 5 Remove the ITU assembly and check that the sensor cable is seated in the handle of the ITU assembly correctly. Note: The sensor connector is located on the side of the ITU handle assembly. Is the cable seated correctly? Go to step 6 Reinstall the cable correctly. Check again for a 100 ITU Error. If 100 ITU Error is displayed, go to step 6 6 The front contamination shield is attached to the font plate of the ITU frame and lies on the top of the ITU belt. Is the front contamination shield lying on the belt? Go to step 7 Position the shield on top of the belt. 7 Make sure the ITU Cleaner Gear (A) is turning. Observe the gear by opening the front Paper Jam Door above the integrated paper tray 1. Observe the white cleaner gear during POR. The gear should turn slowly and smoothly for approximately 8 seconds before the printer displays a 100 ITU error. Is the ITU Cleaner Gear turning? Go to step 11 Go to step 8 8 Check to see if the ITU Drive Roll Gear (A) is turning during POR. Observe the gear by opening the MFP door to its horizontal position. Observe the gear on the left end of the ITU Drive Roll. The ITU Drive Roll Gear should turn for a few seconds slowly and smoothly before the printer posts a 100 ITU error. Does the Gear turn? Go to step 10 Go to step 9 9 Check to see if the ITU Drive Motor is turning during POR. Observe the ITU Motor during POR by removing the Rear Cover. Is the ITU Drive Motor turning? Replace the “ITU drive assembly” Go to step 10 10 Check the printer is setting on a solid flat surface. Is the printer setting on a solid flat surface? Go to step 11 Place the printer on a solid flat surface. 11 Make sure the ITU drive motor assembly cable is correctly installed to the ITU drive motor and at connector location J64 on the system board. Is the cable correctly installed? Go to step 12 Install the cable correctly 12 Make sure the ITU Autoconnect Cable is installed correctly at connector location J72 on the system board. Is the cable correctly installed? Go to step 13 Install the connector/cable correctly 13 Make sure the ITU Autoconnect connector in the printer is seated correctly in the connector plate. Is the connector seated correctly? Replace the following FRUs in the following order: 1. “ITU assembly”. 2. “System board”. Replace the ITU Autoconnect cable.

Error code:	101
Description:	Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable.
Causes:	• Long-Life Maintenance Kit, 650-4360-00
Remedy:	1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts.

Error code:	102
Display:	Service Call 102: Error
Description:	Environmental Sensor Failure An error was detected in the Environmental Sensor circuitry.
Causes:	• Temp/Humidity Sensor, PL9.1.20 • TMP Harness, PL10.1.4
Remedy:	1 Test the Temperature/Humidity Sensor. Run the Service Diagnostics Temperature/ Humidity Sensor test. Does the sensor function correctly? Go to Step 2. Replace the Temp/ Hum Sensor. 2 Check the Humidity signal. Disconnect P/J231. Is the voltage across P/J231-2 <=> P/J231-3 less than +3 V and above +0.5 V. Go to Step 4. Go to Step 3. 3 Check the Temperature signal. Disconnect P/J231. Is the voltage across P/J231-4 <=> P/J231-3 greater than +2.5 V? Go to Step 4. Replace the Engine Control Board. 4 Check for +5 V to the Temperature/ Humidity Sensor. Disconnect P/J231. Is there +5 V across P/J231-1 <=> P/J231-3? Replace the Temp/ Hum Sensor. Replace the Engine Control Board.

Error code:	103
Display:	Service Call 103: Error
Description:	Fuser Motor Failure The Fuser Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Fuser Drive Assembly, PL5.2.25 • TNRFULL/FSR Harness, PL5.2.30 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.1
Remedy:	1 Check the Fuser Drive Assembly for damage. Are any parts of the Fuser Drive Assembly damaged or excessively worn? Replace the Fuser Drive Assembly. Go to Step 2. 2 Check the Fuser Motor connection. Is P/J521 connected to the harness? Go to Step 3. Reconnect the Fuser Motor. 3 Test the Fuser Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Fuser Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Fuser Motor. Is the +24 V across P/J521-10 <=> P/J 521-8? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the TNRFULL/FSR Harness PL5.2.30 for continuity. 1. Disconnect P/J52 and P/J521. 2. Check continuity between J52 <=> J521. Replace the Engine Control Board. Replace the FSR/ ADC Harness.

Error code:	104
Display:	Service Call 104: Error
Description:	Developer Motor Failure The Developer Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Developer Drive Assembly, PL8.1.1 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Developer Drive Assembly for damage. Are any parts of the Developer Drive Assembly damaged or excessively worn? Replace the Developer Drive Assy. Go to Step 2. 2 Check the Developer Motor connection. Is P/J491 connected to the harness? Go to Step 3. Reconnect the Developer Motor. 3 Test the Developer Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Developer Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Developer Motor. Is the +24 V across P/J491-1 <=> P/J 481-5? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J491. 2. Check continuity between J48 <=> J491. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.

Error code:	105
Display:	Service Call 105: Error
Description:	Main Motor Failure The Main Motor rotation signal indicates that the motor is no longer operational.
Causes:	• Main Drive Assembly, PL8.1.2 • Engine Control Board, PL9.1.16 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Check the Main Drive Assembly for damage. Are any parts damaged? Replace the Main Drive Assembly. Go to Step 2. 2 Check the Main Motor connection. Is P/J481 connected to the harness? Go to Step 3. Reconnect the Main Motor. 3 Test the Main Motor. 1. Close the Interlock Switch while testing. 2. Run the Service Diagnostics Main Motor test. Does the motor operate? Go to Step 5. Go to Step 4. 4 Check for +24 V to the Main Motor. Is there +24 V across P/J481-10 <=> P/J 481-8? Go to Step 6. Go to Step 5. 5 Test the Interlock Switch. Run the Service Diagnostics Interlock Switch test. Does the switch function correctly? Go to Step 6. Replace the Interlock Switch. 6 Check all pins on the FAN/PHD/MOT Harness, PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J481. 2. Check continuity between J48 <=> J481. Replace the Engine Control Board. Replace the FAN/PHD/MOT Harness.

Error code:	106
Display:	Service Call 106: Error
Description:	Motor Failure One of the primary drive motors has failed.
Causes:	• Main Drive Assembly, PL8.1.2 • Developer Drive Assembly, PL8.1.1 • Fuser Drive Assembly, PL5.2.25 • Engine Control Board, PL9.1.16 • Interlock Switch, PL9.1.11
Remedy:	1 Check the motors. Run the Service Diagnostics motor tests to determine the failed part. Is the failed part the Main Drive Motor? Go to. Test the Fuser Motor. 2 Is the failed part the Fuser Drive Motor? Go to. Test the Developer Motor. 3 Is the failed part the Developer Drive Motor? Go to. Replace the Engine Control Board.

Error code:	107
Display:	Service Call 107: Error
Description:	Printhead Error
Causes:	Does error reoccur? Is error recovered by reloading PU F/W?
Remedy:	Magenta printhead lost Hsync Check for the correct installation of all the cables to the system board assembly and to the printhead assembly; J11 and J12 on the system board. Go to “System board”. If the cables are connected correctly to the system board and to the printhead assembly, go to “Printhead diagnostics”.

Error code:	201
Display:	ERROR 201 COMMAND
Description:	PU F/W Flash write error (Reserved)
Causes:	• Defective polygon motor • Defective harness
Remedy:	1. Connect the cable correctly. 2. Replace the engine control board. 3. Replace the laser scanning unit. 4. Check or replace the cable.

Деталь:	LVPS 230V
Парткод:	2103385

Деталь:	CLAMP GUIDE HARNESS
Парткод:	2071871

Деталь:	HVPS
Парткод:	2103396

Деталь:	POWER CABLE
Парткод:	2087700

Error code:	202
Display:	ERROR 202 PARAMETER
Description:	Polygon motor error 1: ON timeout
Causes:	The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed.

Error code:	203
Display:	Power OFF/ON 203:Error ssssssssssssssss
Description:	Polygon motor error 2: OFF timeout
Causes:	The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off.

Error code:	204
Display:	Power OFF/ON 204:Error
Description:	Polygon motor error 3: XSCRDY signal error
Causes:	The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing.
Remedy:	• Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board).

Error code:	205
Display:	ERROR 205 47V HEAD VOLTAGE
Description:	No page at DUP IN (Reserved)
Causes:	Disconnected cable from the polygon motor drive board or defective connection. Defective polygon motor or drive board.
Remedy:	1. Check the connectors. 2. Replace the polygon motor. 3. Replace the polygon motor drive board.

Error code:	206
Display:	ERROR 206 MAIN PCB
Description:	Replace Transfer Roller or Transfer Roller Is at End of Life The Toner Full Sensor indicates that the Transfer Roller requires replacement.
Causes:	• Toner Full Sensor, PL5.2.20 • Transfer Roller, PL5.1.4 • TNRFULL/FSR Harness, PL5.2.30
Remedy:	1 Check the following for evidence of fault or damage: • Transfer Roller PL5.1.4 • Toner Full Sensor PL5.2.20 Replace any damaged parts. Go to Step 2. 2 Test the Toner Full Sensor. Run the Service Diagnostics Transfer Roller Toner Full Sensor test. Does the sensor function correctly? Go to Step 5 Go to Step 3. 3 Check the Toner Full Sensor signal. 1. Remove the Transfer Roller Assembly. 2. Disconnect P/J142. Does the voltage between J142-2 <=> J142-3 = 0 V? Go to Step 5. Go to Step 4. 4 Check all pins on the TNRFULL/FSR Harness PL5.2.30 for continuity. 1. Disconnect P/J52 and P/J142. 2. Check continuity between J52 <=> J142. Replace Sensor Toner Full. Replace Toner Full/ FSR Harness. 5 Replace the Transfer Roller. Does the error persist? Replace the Engine Control Board. Complete

Error code:	207
Display:	Power OFF/ON 207:Error
Description:	Replace Fuser The Fuser Life counter indicates that the Fuser has reached its end of life. Fuser replacement is necessary to avoid print quality problems.
Causes:	• Fuser, PL5.1.1 • FSR/ADC Harness PL5.2.28 • EEPROM Board, PL 9.1.12 • EEPROM Harness, PL10.1.8
Remedy:	1 Check the Fuser connector for damage. Re-establish proper connection or replace the parts concerned. Power cycle the printer. Go to Step 2. 2 Replace the Fuser. Does the error persist? Go to Step 3. Complete 3 Replace the EEPROM Board Does the error persist? Go to Step 4. Complete 4 Check all pins on the EEPROM Harness PL10.1.8 for continuity. 1. Disconnect P/J191 and P/J144. 2. Check continuity between J191<=>J144. Go to Step 5. Replace the EEPROM Harness. 5 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and J361. 2. Check continuity between J36 <=> J361. Replace the Engine Control Board. Replace the FSR/ADC Harness.

Error code:	208
Display:	Power OFF/ON 208:Error
Description:	Parameter error
Causes:	• Harness to the IPU disconnected • Harness inside the laser unit CK disconnected • Polygon motor drive board defective • IPU defective
Remedy:	1. Check the harness connection to the IPU. 2. Check the harness connection inside the laser unit CK. 3. Replace the polygon motor drive board. 4. Replace the IPU.

Error code:	209
Display:	Power On/off 209: DOWNLOAD ERROR
Description:	Custom Media Table Download Error Failed to download custom media table.
Remedy:	Failed to download custom media table. After turning ON the power again, try downloading again. (This process isn’t executed for regular operations, therefore, will not occur)

Error code:	210
Description:	EM Null page cargo
Causes:	• Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB
Remedy:	1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU.

Error code:	211
Display:	ERROR 211 HeadWARM.THERM(----)
Description:	EM Null page
Causes:	• Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB
Remedy:	1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU.

Epson AcuLaser C4200DNPC5

Общие характеристики

Факс

Печать фотографий

Телефон

Копир

Сканер

Тип устройства

Макс. формат

Цветность печати

Размещение

Технология печати

Тип

Число страниц в месяц

Область применения

Принтер

Прямая печать

Пигментные чернила

Печать без полей

Двусторонняя печать

Количество цветов

Макс, разрешение для ч/б печати

Скорость ч/б печати

Время выхода первого отпечатка

Сканер

Стандарт WIA

Стандарт TWAIN

Отправка изображения по e-mail

Расходные материалы

Ресурс ч/б картриджа/тонера

Количество картриджей

Ресурс фотобарабана

Ресурс цветного картриджа/тонера

Печать на:

Плотность бумаги

Факс

Цветной

Телефон

Стандарт DECT

Проводная трубка

Беспроводная трубка

АОН

Caller ID

Автоответчик

Спикерфон

Шрифты и языки управления

Языки управления

Количество установленных шрифтов

Подача бумаги

Финишер

Сортировка со сдвигом

Брошюровщик

Степлер

Электронная сортировка

Сортер

Интерфейсы

LPT

USB

Веб-интерфейс

Ethernet (RJ-45)

Устройство для чтения карт памяти

Bluetooth

Wi-Fi

RS-232

Инфракрасный порт

FireWire (IEEE 1394)

Версия USB

Память/Процессор

Частота процессора

Макс, объем памяти

Объем памяти

Процессор

Дополнительная информация

Мин. системные требования

Поддержка ОС

Потребляемая мощность

Уровень шума

Габариты

Высота

Ширина

Error code:	212
Description:	Install or Reseat Imaging Unit The Imaging Unit CRUM fails to detect the Imaging Unit.
Causes:	• Imaging Unit, PL6.1.1 • CRUM Connector, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9
Remedy:	1 Remove the Imaging Unit. Inspect the printer cavity for damage, debris, and toner under the auger area preventing the Imaging Unit from being seated properly. Is there foreign material or damage? Remove foreign material. Vacuum out loose toner if found. Go to Step 2. 2 Inspect and reseat the Imaging Unit. Does the error persist?. Go to Step 3. Complete 3 Check Imaging Unit CRUM connection. Are P/J710 and P/J484 connected? Go to Step 4. Reconnect the CRUM. 4 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J484<=>J710. Go to Step 5 Replace PHD2 Harness. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J484 and P/J48. 2. Check continuity between J48 <=> P484. Go to Step 6 Replace the FAN/PHD/MOT Harness 6 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete

Error code:	213
Display:	Power OFF/ON 213:Error
Description:	Install or Reseat Transfer Roller The printer does not detect the presence of the Transfer Roller.
Causes:	• CTD (ADC) Sensor, PL5.2.19 • Transfer Roller, PL5.1.4 • FSR/ADC Harness, PL5.2.28
Remedy:	1 Check the following for evidence of fault or damage: • Transfer Roller PL5.1.4 • CTD (ADC) Sensor PL5.2.19 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Clean the CTD (ADC) Sensor. Does this fix the problem? Complete Go to Step 3. 3 Test the CTD (ADC) Sensor. Run the Service Diagnostics CTD (ADC) Sensor test. Does the sensor function correctly? Go to Step 4. Go to Step 5. 4 Replace the Transfer Roller. Does the error persist? Go to Step 5. Complete 5 Check the CTD (ADC) Sensor connection. Is P/J136 connected to the harness? Go to Step 6. Connect the sensor. 6 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136. 2. Check continuity between J36 <=> J136. Go to Step 7. Replace the FSR/ ADC Harness. 7 Check the CTD (ADC) Sensor signal. Disconnect P/J36. Does J36-2 <=> J36-5 = 0 V? Replace the CTD (ADC) Sensor. Replace the Engine Control Board.

Error code:	214
Display:	Power OFF/ON 214:Error
Description:	Install or Reseat Fuser The printer does not detect the presence of the Fuser.
Causes:	• Fuser, PL5.1.1 • FSR/ADC Harness PL5.2.28
Remedy:	1 Cycle power to the printer. Does the error persist? Go to Step 2. Complete 2 Check the Fuser for damage. Is the Fuser damaged? Replace the Fuser, then cycle power. Go to Step 3. 3 Check Fuser resistance. 1. Remove the Fuser. 2. Disconnect J361. 3. Is the resistance between P361-B5 <=> P361-B4 less than 400KΩ? 4. Is the resistance between P361-B5 <=> P361-B4 less than 7MΩ? Go to Step 4. Replace the Fuser. 4 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and J361. 2. Check continuity between J36 <=> J361. Replace the Engine Control Board. Replace the FSR/ADC Harness.

Error code:	215
Description:	DEVE ASSY (K), (C), (M) and (Y) reached its end of life.
Remedy:	1 Initial Check Are the parts listed below installed incorrectly? • FRAME ASSY DEVE • DEVE ASSY (Y/M/C/K) Reinstall the part(s) correctly. Go to Step [2]. 2 Replacing Check of the DEVE ASSY (Y/M/ C/K) Replace the DEVE ASSY that caused the error. Does the error still occur after the replacement? Replace the PWBA MCU IDTN. End of procedure