Epson AcuLaser C8500

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

100000

Цветность печати

цветная

Общие характеристики
Макс. формат	A3
Область применения	большой офис
Число страниц в месяц	100 000
Технология печати	лазерная
Тип	лазерный/светодиодный
Цветность печати	цветная
Тип устройства	Принтер
Печать фотографий
Сканер
Копир
Принтер
Количество цветов	4
Двусторонняя печать
Прямая печать
Макс, разрешение для ч/б печати
По Y	600
По X	600
Скорость цветной печати
A4	6
Расходные материалы
Ресурс ч/б картриджа/тонера	5 500
Ресурс цветного картриджа/тонера	6 000
Печать на:
Пленках
Фотобумаге
Этикетках
Лотки
Подача бумаги
Стандартная	250
Вывод бумаги
Стандартный	250
Интерфейсы
Инфракрасный порт
USB
Ethernet (RJ-45)
LPT
Память/Процессор
Макс, объем памяти	768
Объем памяти	64
Дополнительная информация
Мин. системные требования	Intel 486
Поддержка ОС
Windows
Mac OS
DOS
Linux
Уровень шума
При работе	55
Габариты
Вес	71
Ширина	646
Глубина	554
Высота	650

Коды ошибок

0017 ... 0309

0800

0998

0999

1002

1010

1020, 1021

1100, 1101

1120 ... 1123

113

1180 ... 1185

1200, 1210

1400

1500

1550

1600

1999

2000

510

511

512

513

516

517

520

521

523

524

525

526

527

530

531

532

533

534

535

536

537

543

544

545

546

547

620

621

622

623

624

626

627

830

831

832

833

998

Описание

Парткод

Название

EPSON Коллектор обработанного тонера

EPSON Тонер-картридж черный

EPSON Тонер-картридж желтый

EPSON Тонер-картридж пурпурный

EPSON Тонер-картридж голубой

EPSON Блок фотобарабана

Error code:	0017 ... 0309
Description:	0017 CPU error (Undefined interrupt occurrence) 0081 CPU error (TLB correction exception) Only AcuLaser C7000 0082 CPU error (TLB miss exception [Load/Fetch]) Only AcuLaser C7000 0083 CPU error (TLB miss exception [Store]) Only AcuLaser C7000 0084 CPU error (Address error exception [Load/ Fetch]) Only AcuLaser C7000 0085 CPU error (Address error exception [Store]) Only AcuLaser C7000 0086 CPU error (Bus error exception [Fetch]) Only AcuLaser C7000 0087 CPU error (Bus error exception [Load/Store]) Only AcuLaser C7000 0088 CPU error (SYSCALL exception) 0089 CPU error (Break exception) 0090 CPU error (Reserve command exception) Only AcuLaser C7000 0091 CPU error (Unused coprocessor exception) 0092 CPU error (FPU exception) Only AcuLaser C7000 0093 CPU error (TLB exception) Only AcuLaser C7000 0094 CPU error (XTLB exception) Only AcuLaser C7000 0095 CPU error (Cache exception) Only AcuLaser C7000 0096 CPU error (Trap exception) Only AcuLaser C7000 0097 CPU Error (FPU exception) Only AcuLaser C7000 0098 CPU error (Watch exception) Only AcuLaser C7000 0128 ~ 0254 CPU error (Undefined trap) Only AcuLaser C7000 0255 CPU error (NMI exception) Only AcuLaser C7000 0256 CPU error (Divide by 0) Only AcuLaser C7000 0257 CPU error (Computation overflow) Only AcuLaser C7000 0258 CPU error (Break was generated) Only AcuLaser C7000 0300 CPU error (Reserved (undefined) exception) Only AcuLaser C8600 0301 CPU error (Machine check exception) Only AcuLaser C8600 0302 CPU error (Data access exception) Only AcuLaser C8600 0303 CPU error (Instruction access exception) Only AcuLaser C8600 0304 CPU error (Alignment exception) Only AcuLaser C8600 0305 CPU error Only AcuLaser C8600 0306 CPU error (Trace exception) Only AcuLaser C8600 0307 CPU error Only AcuLaser C8600 0308 CPU error (System administration interrupt exception) Only AcuLaser C8600 0309 CPU error (Temperature management interrupt exception) Only AcuLaser C8600
Remedy:	1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. • Reinsert the DIMM. Replace or reinstall the relevant part. Go to step 2 2 • Improving the CONTROLLER PWB Environment: • Update the program to the latest one in the DIMM.ÅB Replace or reinstall the relevant part. Go to step 3 3 • Replacing the CONTROLLER PWB and Performing Checks: Does the problem still occur after replacing the MCU PWB with a normal one? - Problem solved

Error code:	0800
Display:	Print Unable 08 Turn the power off and then back on again.
Description:	Image processing error JAM010X is detected twice.
Causes:	Defective main PWB.
Remedy:	Main PWB Replace the main PWB.

Error code:	0998
Description:	Engine communication error (Only when powering on)
Remedy:	1 • Initial checking: Is there any parts of wrong specifications used, improper mounting, damage, distortion, dirt, or adherence of foreign matter? • Major parts to be checked: COMMUNICATION PWB,MCU PWB Replace or reinstall the relevant part. Go to step 2 2 Does the error occur when the power is turned ON? Go to step 3 Go to the relevant FIP when other errors/status codes occur. 3 Does the error occur when MCU PWB is replaced and the power is turned ON again? Go to FIP-2.33 “Noise” Problem solved

Error code:	0999
Description:	No Engine Flash ROM program data
Remedy:	1 • Initial checking: Is there any parts of wrong specifications used, improper mounting, damage, distortion, dirt, or adherence of foreign matter? • Major parts to be checked: COMMUNICATION PWB,MCU PWB Replace or reinstall the relevant part. Go to step 2 2 Does the error occur when the power is turned ON? Go to step 3 Go to the relevant FIP when other errors/status codes occur. 3 Does the error occur when MCU PWB is replaced and the power is turned ON again? Go to FIP-2.33 “Noise” Problem solved

Error code:	1002
Description:	Standard RAM error (When the standard size is not determined, etc.)
Remedy:	1 • Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2 2 • Checking the SD-RAM: • Remove all SD-RAMs from the RAM slots and then reinsert them in the RAM slots. Be sure to insert the SD-RAMs one by one (S0 and S1) in order so that the SD-RAM error can be identified. Every time you insert an SD-RAM, follow the procedures below and repeat it for each one. 1 Turn the power off. 2 Add the SD-RAM 3 Turn the power on. • Insert the SD-RAM in the socket until it is locked securely. NOTE: Since the SD-RAM has the right direction to insert, be sure to insert it in the correct direction. Replace or reinstall the relevant part. Problem solved

Error code:	113
Display:	SVC 113 ERROR
Description:	Finisher Stapler Failure, Code 113 The staple home sensor doesn’t turn ON within 2 seconds after the stapler motor started to turn backwards.
Causes:	• Finisher Control Board • Staple Unit Assembly
Remedy:	1 1. Enter service diagnostics. 2. Run the Stapler Home sensor test. 3. Does the value change from H to L when the stapler is moved away from the home position? Go to step 6. Go to step 2. 2 1. Measure the voltage between finisher board connector P852-2 and frame ground. 2. Does the voltage change between 0 and +5 VDC when the sensor is blocked and unblocked? Replace the finisher control board. Go to step 3. 3 1. Measure the voltage at the Finisher Board connector P852-1. 2. Dose the voltage measure +5 VDC? The home sensor or the wiring is bad. Replace the staple unit assembly. Go to step 4. 4 1. Disconnect the Stapler Unit Assembly. 2. Measure the voltage between the finisher board connector P852-1 and frame ground. 3. Does the voltage measure +5 VDC? Replace the stapler unit assembly. Go to step 5. 5 Is +24 VDC present at either J847-7 or J847-9? Replace the finisher control board. Troubleshoot and repair the +24 VDC interlock circuit. 6 1. Enter service diagnostics and run the “Stapler Close Motor” test. 2. Does the stapler motor operate correctly? Replace the finisher control board. Go to step 7. 7 With the Stapler Close Motor test running is +24 VDC present at J847-7? Replace in the following order: • stapler head assembly • finisher control board Troubleshoot and repair the +24 VDC interlock circuit.

Error code:	510
Display:	SYSTEM HALT (*) 510 : X ORGIN
Description:	Replace green developer
Causes:	• Tray lift motor defective or connector disconnected • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective
Remedy:	1. Check the harness connection or replace it. 2. Replace the bypass tray lift motor. 3. Replace the bypass upper limit sensor. 4. Replace the bypass lower limit sensor. 5. Check or clear obstacles around the bypass pick-up solenoid.

Error code:	511
Display:	SYSTEM HALT (*) 511 : Z ORGIN
Description:	A3 LCT exit roller contact motor 1 error. One of the following conditions is detected in the A3 LCT. • The LCT exit roller sensor is not activated within 225 pulses after the LCT exit roller contact motor has turned on at its initialization. • The LCT exit roller sensor detects for 25 pulses even after the LCT exit roller has moved away from its home position. • The LCT exit roller sensor does not detect within 25 pulses after the LCT exit roller has moved back to its home position.
Causes:	• Poor connection or defective LCT exit roller contact motor • Poor connection or defective LCT exit roller sensor
Remedy:	1. Check the harness connection. 2. Replace the LCT exit roller contact motor. 3. Replace the LCT exit roller sensor.

Error code:	512
Display:	CAPSHTR ORGIN
Description:	Replace brown developer
Causes:	• Poor connection or defective LCT exit roller contact motor • Poor connection or defective LCT exit roller sensor
Remedy:	1. Check the harness connection. 2. Replace the LCT exit roller contact motor. 3. Replace the LCT exit roller sensor.

Error code:	513
Display:	ERROR 513 !MEDIA HEIGHT
Description:	Copy cartridge (drum unit) will need replacing soon
Remedy:	1. Check the state of the Jam Detection Sensor. 2. Check the connector connection of the Jam Sensor and check the connection route. 3. Replace the Jam Detection Sensor (L/R) with a new one. 4. Replace the Slider PCB with a new one. 5. Replace the Main PCB with a new one.

Error code:	516
Display:	ERROR 516 MEDIA SET POSITION L
Description:	DADF feed rollers should be replaced
Causes:	• Loose connection between the BCU and the duplex unit controller board
Remedy:	1. Check the media setting position. 2. Perform cleaning of the media width sensor. 3. Execute [#TEST PAPER SENSOR].

Error code:	517
Description:	Replace exposure lamp
Causes:	• One of the fuses on the duplex unit controller has blown. NOTE: The fuses prevent excess electricity from flowing into the motors.
Remedy:	2/1 Optional Cassette Unit error, or 2/1 Optional Cassette Unit other than this printer`s option is installed

Error code:	520
Description:	Replace optics filter
Causes:	• Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective

Error code:	521
Description:	Replace particle filter
Causes:	• Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective

Error code:	523
Description:	Replace fuser pawls
Causes:	• Fusing oil not circulated in the fusing unit • Overload to the fusing motor • Poor connection or defective LCT exit roller contact motor
Remedy:	1. Check or replace the fusing unit. 2. Check if remaining paper or obstruction in the fusing unit stops the fusing motor drive. 3. Replace the fusing motor.

Error code:	524
Description:	Paper exit motor error • The machine detects a rotation error of the paper exit motor for 0.1 second after the paper exit motor has rotated for 0.9 second. • The machine does not detect any signal from the paper exit motor for 0.1 second when the paper exit motor is in the ready condition
Causes:	• Paper jam in the paper exit area • Incorrect rotation speed setting of the paper exit motor • Incorrect rotation speed setting of the fusing motor • Defective paper exit motor • Defective PDB.
Remedy:	1. Remove the paper jam. 2. Input the default setting for the paper exit motor with SP1-805-001. 3. Input the default setting for the fusing motor with SP1-907-001. 4. Replace the paper exit motor. 5. Replace the PDB.

Error code:	525
Description:	Transport motor error: bank 1 The machine detects a Lock signal from a bank 1 transport motor after the motor turned on.
Causes:	Motor overload. Defective motor. Disconnected connectors. Broken harness.
Remedy:	1. Turn off and on the main power switch. 2. Check or connect the connectors. 3. Replace the harness. 4. Replace the motor.

Error code:	526
Description:	Transport motor error: bank 2 The machine detects a Lock signal from a bank 2 transport motor after the motor turned on.
Causes:	Motor overload. Defective motor. Disconnected connectors. Broken harness.
Remedy:	1. Turn off and on the main power switch. 2. Check or connect the connectors. 3. Replace the harness. 4. Replace the motor.

Error code:	527
Description:	Deve home position sensor malfunction

Error code:	530
Description:	LSU Fan Motor Error
Causes:	A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued.
Remedy:	• Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor.

Error code:	531
Description:	Fusing Fan Motor Error
Causes:	A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued.
Remedy:	• Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor.

Error code:	532
Description:	IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on.
Causes:	• Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB
Remedy:	1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB.

Error code:	533
Description:	IH inverter fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH inverter fan turns on.
Causes:	• Disconnected harness • Overload on the IH inverter fan motor • Defective IH inverter fan motor • Defective IOB
Remedy:	1. Check or replace the harness. 2. Replace the IH inverter fan. 3. Replace the IOB.

Error code:	534
Description:	Second duct fan error The machine does not detect the fan motor lock signal for 2 seconds while the second duct fan turns on.
Causes:	• Disconnected harness • Overload on the second duct fan motor • Defective second duct motor • Defective IOB
Remedy:	1. Check or replace the harness. 2. Replace the second duct fan. 3. Replace the IOB.

Error code:	535
Description:	Paper exit fan error The lock sensor value is monitored every 100 ms when the motor is ON. If the retrieval of the lock signal fails 100 times consecutively, it is determined as a failure to rotate properly.
Causes:	Motor overload. Defective motor. Loose connection. Broken harness. Defective IOB.
Remedy:	• Replace the motor. • Reconnect the connector. • Replace the harness. • Replace the IOB.