Epson M205
Рейтинг
Модули
CASE-012
MECH-011
ELEC-011
MECH-022
SC-011
Детали ELEC-011
| Деталь: | HOUSING,RIGHT |
| Парткод: | 1586035 |
| Деталь: | HOUSING,LEFT |
| Парткод: | 1572580 |
| Деталь: | HOUSING,FRONT |
| Парткод: | 1572579 |
| Деталь: | COVER,REAR |
| Парткод: | 1548609 |
| Деталь: | STACKER ASSY., B,SEC |
| Парткод: | 1624161 |
| Деталь: | PAPER SUPPORT, C |
| Парткод: | 1595368 |
| Деталь: | PAPER SUPPORT,SUPPORT |
| Парткод: | 1572583 |
| Деталь: | HINGE,ASSY., B |
| Парткод: | 1438860 |
| Деталь: | COVER,ETHER |
| Парткод: | 1572611 |
| Деталь: | COVER,RIGHT |
| Парткод: | 1586036 |
| Деталь: | PANEL ASSY,CD07., EHK,SEC |
| Парткод: | 1594872 |
| Деталь: | HOUSING,PANEL,UPPER, C |
| Парткод: | 1588373 |
| Деталь: | LOCK,SCANNER ASSY.,SEC |
| Парткод: | 1594811 |
| Деталь: | HARNESS |
| Парткод: | 2146483 |
| Деталь: | POWER CABLE |
| Парткод: | 2121764 |
| Деталь: | LEVER,DETECTOR,PE,HD |
| Парткод: | 1572338 |
| Деталь: | ROLLER,EJ |
| Парткод: | 1548500 |
| Деталь: | SPUR GEAR,31.2 |
| Парткод: | 1548501 |
| Деталь: | MOTOR ASSY.,PF |
| Парткод: | 1548502 |
| Деталь: | BOARD ASSY.,SUB |
| Парткод: | 2147998 |
| Деталь: | HOLDER RETARD ASSY.,SEC |
| Парткод: | 1584704 |
| Деталь: | FRAME PUMP ASSY,B, SEC |
| Парткод: | 1597297 |
| Деталь: | HOLDER STARWHEEL ASSY,CC83.,SEC |
| Парткод: | 1594281 |
| Деталь: | SHAFT,ROLLER,LD,ASSY, IEI |
| Парткод: | 1573559 |
| Деталь: | SCALE,CR, B |
| Парткод: | 1603525 |
| Деталь: | EXTENSION SPRING,1.41 |
| Парткод: | 1548480 |
| Деталь: | CAP ASSY.,IEI |
| Парткод: | 1577546 |
| Деталь: | MOTOR ASSY,CR |
| Парткод: | 2142590 |
| Деталь: | PGU ASSY |
| Парткод: | 1550812 |
| Деталь: | CR ASSY,CC83.,SEC |
| Парткод: | 1594288 |
| Деталь: | FFC CR ASSY,CC83.,SEC |
| Парткод: | 1594289 |
| Деталь: | LEVER,PAPER BACK |
| Парткод: | 1549887 |
| Деталь: | SCALE,PF |
| Парткод: | 1548518 |
| Деталь: | ROLLER PF ASSY.,SEC |
| Парткод: | 1584705 |
| Деталь: | TIMING BELT, CR |
| Парткод: | 1572545 |
| Деталь: | CLUTCH |
| Парткод: | 1548528 |
| Деталь: | SPUR GEAR,37.2 |
| Парткод: | 1548529 |
| Деталь: | EXTENSION SPRING,0.137 |
| Парткод: | 1548530 |
| Деталь: | EXTENSION SPRING,0.067 |
| Парткод: | 1548494 |
| Деталь: | POROUSPAD,IS,LOWER |
| Парткод: | 1572561 |
| Деталь: | SHEET,SCALE,PF |
| Парткод: | 1572544 |
| Деталь: | COVER,MOTER,PF |
| Парткод: | 1572587 |
| Деталь: | HOLDER,PULLEY,PF ASSY.,SEC |
| Парткод: | 1584712 |
| Деталь: | PRINT HEAD,ID9150 |
| Парткод: | FA11000 |
| Деталь: | HOLDER,BOARD |
| Парткод: | 1548476 |
| Деталь: | HOPPER ASSY.,SEC |
| Парткод: | 1584716 |
| Деталь: | TRAY POROUSPAD,ASSY.,SEC |
| Парткод: | 1584721 |
| Деталь: | CAP,TANK |
| Парткод: | 1584650 |
| Деталь: | TANK,SUPPLY,ASSY.,CC83, B,SEC |
| Парткод: | 1660225 |
| Деталь: | ADAPTER,ASSY.,CC83,SEC |
| Парткод: | 1594328 |
| Деталь: | JOINT,TUBE |
| Парткод: | 1586029 |
| Деталь: | HOUSING,TANK |
| Парткод: | 1586042 |
| Деталь: | LEVER VALVE, B |
| Парткод: | 1564366 |
| Деталь: | LABEL,VALVE,POSITION |
| Парткод: | 1590446 |
| Деталь: | VALVE,TANK,ASSY.,CC83,SEC |
| Парткод: | 1594325 |
| Деталь: | GUIDE PLATE,TUBE |
| Парткод: | 1586032 |
| Деталь: | GUIDE PLATE,TUBE,SUPPORT |
| Парткод: | 1586033 |
| Деталь: | TUBE,ADPTER |
| Парткод: | 1584660 |
| Деталь: | COVER,TANK |
| Парткод: | 1586045 |
| Деталь: | COMPRESSION SPRING,3.43 |
| Парткод: | 1495647 |
| Деталь: | COVER,CR |
| Парткод: | 1586028 |
| Деталь: | LABEL,VALVE,POSITION,EXPLANATION, C |
| Парткод: | 1590704 |
| Деталь: | LABEL,INK INSTRUCTION,T774/ASIA |
| Парткод: | 1593810 |
| Деталь: | LABEL,SETUP,INSTRUCTION, C |
| Парткод: | 1590706 |
| Деталь: | POROUS PAD,TANK,SIDE |
| Парткод: | 1590138 |
| Деталь: | POROUS PAD,TANK,UPPER |
| Парткод: | 1596457 |
| Деталь: | GREASE G-45 |
| Парткод: | 1033657 |
| Деталь: | GREASE G-74 |
| Парткод: | 1409257 |
| Деталь: | I/P,DPIC009BSP,110,PRINTING |
| Парткод: | 1462531 |
| Деталь: | GREASE G-71(BLUE) |
| Парткод: | 1480655 |
| Деталь: | SONIC TENSION METER U508 |
| Парткод: | 1640645 |
| Деталь: | SHIPPING CLEANING LIQUID,CR06A,1kg |
| Парткод: | 6104713 |
| Деталь: | BOARD ASSY.,MAIN |
| Парткод: | 2172238 |
| Деталь: | WIRELESS LAN USB MODULE |
| Парткод: | 2171673 |
| Деталь: | POWER SUPPLY UNIT |
| Парткод: | 2155567 |
| Деталь: | PRINT HEAD,ID9150 |
| Парткод: | FA11000 |
| Деталь: | HOLDER,BOARD |
| Парткод: | 1548476 |
| Деталь: | HOPPER ASSY.,SEC |
| Парткод: | 1584716 |
| Деталь: | TRAY POROUSPAD,ASSY.,SEC |
| Парткод: | 1584721 |
| Деталь: | CAP,TANK |
| Парткод: | 1584650 |
| Деталь: | TANK,SUPPLY,ASSY.,CC83, B,SEC |
| Парткод: | 1660225 |
| Деталь: | ADAPTER,ASSY.,CC83,SEC |
| Парткод: | 1594328 |
| Деталь: | JOINT,TUBE |
| Парткод: | 1586029 |
| Деталь: | HOUSING,TANK |
| Парткод: | 1586042 |
| Деталь: | LEVER VALVE, B |
| Парткод: | 1564366 |
| Деталь: | LABEL,VALVE,POSITION |
| Парткод: | 1590446 |
| Деталь: | VALVE,TANK,ASSY.,CC83,SEC |
| Парткод: | 1594325 |
| Деталь: | GUIDE PLATE,TUBE |
| Парткод: | 1586032 |
| Деталь: | GUIDE PLATE,TUBE,SUPPORT |
| Парткод: | 1586033 |
| Деталь: | TUBE,ADPTER |
| Парткод: | 1584660 |
| Деталь: | COVER,TANK |
| Парткод: | 1586045 |
| Деталь: | COMPRESSION SPRING,3.43 |
| Парткод: | 1495647 |
| Деталь: | COVER,CR |
| Парткод: | 1586028 |
| Деталь: | LABEL,VALVE,POSITION,EXPLANATION, C |
| Парткод: | 1590704 |
| Деталь: | LABEL,INK INSTRUCTION,T774/ASIA |
| Парткод: | 1593810 |
| Деталь: | LABEL,SETUP,INSTRUCTION, C |
| Парткод: | 1590706 |
| Деталь: | POROUS PAD,TANK,SIDE |
| Парткод: | 1590138 |
| Деталь: | POROUS PAD,TANK,UPPER |
| Парткод: | 1596457 |
| Деталь: | SCANNER UNIT,CC83, B,ASP |
| Парткод: | 1686337 |
| Деталь: | COVER,ASF |
| Парткод: | 1590188 |
| Деталь: | ADF UNIT,CE36, D,ASP |
| Парткод: | 1680571 |
| Деталь: | PAPER SUPPORT ADF ASSY.,SEC |
| Парткод: | 1585900 |
| Деталь: | ADF COVER ASSY.,CE36,SEC |
| Парткод: | 1646289 |
| Деталь: | PAD ADF ASSY.,SEC |
| Парткод: | 1585902 |
| Деталь: | BEVEL GEAR SHAFT,10.4 |
| Парткод: | 1574388 |
| Деталь: | COMBINATION GEAR,24,9.6 |
| Парткод: | 1574387 |
Коды ошибок
01H
02H
03H
04H
08H
09H
0AH
10H
14H
20H
36H
40H
41H
42H
43H
50H
56H
5BH
80H
D1H
D2H
D3H
D4H
Displaying
F1H
F2H
F3H
F4H
F8H
F9H
FAH
Описание
| Error code: | 01H |
| Description: | ADF PID excess speed (Printer) |
| Causes: | • ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • Motor driver failure (Main Board failure) |
| Remedy: | • Checking the operation of the Carriage Assy; Move the Carriage Assy by hand, and check to see if it moves smoothly. • Making the following adjustments • Bi-D • Paper feed length with PF Assy • Paper feed length with Eject Assy • PW adjustment • Checking the following parts and replacing the defective one • Checking the head FFC (CN10/11/12) for disconnection or breakage • Checking the lead wires of the CR Motor (CN14) for disconnection or breakage • Checking the CR Encoder FFC (CN1) for disconnection or breakage • Checking the printer frame for adhesion of dirt or insufficient lubrication • Checking the CR Guide Shaft for adhesion of dirt or insufficient lubrication • Checking the Linear Scale for adhesion of dirt or damage • Checking the CR Encoder for adhesion of dirt or damage • Checking the PW Sensor for adhesion of dirt or damage • Checking the CR Belt for damage or improper tension • Checking the CR Motor and replacing it if necessary • Main Board • Power Supply Board |
| Error code: | 02H |
| Description: | ADF PID reverse (Printer) |
| Causes: | • ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • Paper jam |
| Remedy: | • Checking the operation of the Carriage Assy; Move the Carriage Assy by hand, and check to see if it moves smoothly. • Making the following adjustments • Bi-D • Paper feed length with PF Assy • Paper feed length with Eject Assy • PW adjustment • Checking the following parts and replacing the defective one • Checking the head FFC (CN10/11/12) for disconnection or breakage • Checking the lead wires of the CR Motor (CN14) for disconnection or breakage • Checking the CR Encoder FFC (CN1) for disconnection or breakage • Checking the printer frame for adhesion of dirt or insufficient lubrication • Checking the CR Guide Shaft for adhesion of dirt or insufficient lubrication • Checking the Linear Scale for adhesion of dirt or damage • Checking the CR Encoder for adhesion of dirt or damage • Checking the PW Sensor for adhesion of dirt or damage • Checking the CR Belt for damage or improper tension • Checking the CR Motor and replacing it if necessary • Main Board • Power Supply Board |
| Error code: | 03H |
| Description: | ADF PID lock (Printer) |
| Causes: | • ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • ADF Motor failure • Paper jam • Cable disconnection |
| Error code: | 04H |
| Description: | Printer control board malfunction • Communications with the M/C expansion IO G/A (IC on the printer control board) are not properly carried out. |
| Causes: | • CR Encoder failure (contaminated/detached scale, Encoder Board failure) • CR Motor failure • Carriage overload error (paper jam/foreign object) • Cable disconnection |
| Remedy: | 1 Check the PRCB connector for proper connection and correct as necessary. 2 Change PRCB. |
| Error code: | 08H |
| Description: | Main motor malfunction • The motor lock signal remains HIGH for a predetermined consecutive period of time while the main motor remains energized. • The motor lock signal remains LOW for a predetermined consecutive period of time while the main motor remains deenergized. |
| Causes: | • CR Encoder failure (contaminated/detached scale, Encoder Board failure) • Tooth skip of the CR Timing Belt • Improper tension of the CR Timing Belt • Paper jam |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M1 operation check. PRCB PJ8PRCB-5 (REM) PRCB PJ8PRCB-8 (LOCK) C-4. 5 Change PRCB. 6 Change DCPU1. |
| Error code: | 09H |
| Description: | Printer: CR load position excess speed error |
| Causes: | • CR Encoder failure (contaminated/detached scale, Encoder Board failure) • Motor driver failure (Main Board failure) • Tooth skip of the CR Timing Belt • Improper tension of the CR Timing Belt |
| Error code: | 0AH |
| Description: | Printer: CR load position excess load error |
| Causes: | • CR Encoder failure (contaminated/detached scale, Encoder Board failure) • CR Motor failure • Carriage overload error (paper jam/foreign object) • Cable disconnection |
| Remedy: | • Checking the operation of the Carriage Assy; Move the Carriage Assy by hand, and check to see if it moves smoothly. • Making the following adjustments • Bi-D • Paper feed length with PF Assy • Paper feed length with Eject Assy • PW adjustment • Checking the following parts and replacing the defective one • Checking the head FFC (CN10/11/12) for disconnection or breakage • Checking the lead wires of the CR Motor (CN14) for disconnection or breakage • Checking the CR Encoder FFC (CN1) for disconnection or breakage • Checking the printer frame for adhesion of dirt or insufficient lubrication • Checking the CR Guide Shaft for adhesion of dirt or insufficient lubrication • Checking the Linear Scale for adhesion of dirt or damage • Checking the CR Encoder for adhesion of dirt or damage • Checking the PW Sensor for adhesion of dirt or damage • Checking the CR Belt for damage or improper tension • Checking the CR Motor and replacing it if necessary • Main Board • Power Supply Board |
| Error code: | 10H |
| Description: | Polygon motor malfunction • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the polygon motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the polygon motor remains energized. |
| Causes: | • CIS Unit failure • Scanner Housing failure • Main Board failure |
| Remedy: | 1 Check the cable and connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PRCB. |
| Error code: | 14H |
| Description: | 2nd image transfer pressure /retraction failure • The state of the retraction position sensor/2nd image transfer is not changed from the unblocked to blocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/2nd image transfer is in the unblocked state even after the lapse of a predetermined period of time during predrive. • The retraction position sensor/2nd image transfer is not blocked (roller in the retracted position) within a predetermined period of time after the retraction sequence of the 2nd transfer roller has been started. • The retraction position sensor/2nd image transfer is not unblocked (roller in the pressed position) within a predetermined period of time after the pressure sequence of the 2nd transfer roller has been started. |
| Causes: | • Pickup Encoder failure (contaminated/detached scale, Encoder Board failure) • Pickup Motor failure • Pickup drive mechanism (2nd cassette) overload (paper jam/foreign object) • Cable disconnection |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the SD4 connector for proper connection and correct as necessary. 4 Check the PRCB connector for proper connection and correct as necessary. 5 PS5 sensor check. PRCB PJ14PRCB-3 (ON) J to K-3. 6 SD4 operation check. PRCB PJ11PRCB-2 (REM) J to K-1. 7 M1 operation check. PRCB PJ8PRCB-5 (REM) PRCB PJ8PRCB-8 (LOCK) C-4. 8 Change PRCB. |
| Error code: | 20H |
| Description: | LED light failure (Printer) |
| Causes: | • CIS Unit failure • Main Board failure |
| Error code: | 36H |
| Description: | Paper jam error (Printer) |
| Causes: | • Paper jam • Foreign objec |
| Error code: | 40H |
| Description: | Printer: Transistor temperature error |
| Causes: | • Main Board failure |
| Remedy: | • Checking the following parts and replace the defective one: • Printhead • Main Board • Power Supply Board • Replace the Head FFC |
| Error code: | 41H |
| Description: | FB PID excess speed (Printer) |
| Causes: | • ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • Motor driver failure (Main Board failure) |
| Remedy: | • Checking the following parts and replace the defective one: • Printhead • Main Board • Power Supply Board • Replace the Head FFC |
| Error code: | 42H |
| Description: | FB PID reverse (Printer) |
| Causes: | • ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • Paper jam |
| Remedy: | • Checking the following parts and replace the defective one: • Printhead • Main Board • Power Supply Board • Replace the Head FFC |
| Error code: | 43H |
| Description: | FB PID lock (Printer) |
| Causes: | • ADF Encoder failure (contaminated/detached scale, Encoder Board failure) • ADF Motor failure • ADF drive mechanism overload (assembling failure, lubrication failure) • Cable disconnection |
| Remedy: | • Checking the following parts and replace the defective one: • Printhead • Main Board • Power Supply Board • Replace the Head FFC |
| Error code: | 50H |
| Description: | Printer: Home position error |
| Causes: | • Paper jam • Foreign object • Deformation of the Main Frame |
| Remedy: | See Remedy for DC error (CR motor) |
| Error code: | 56H |
| Description: | Printer: Contact error at ink replacement timing (Power-off) |
| Causes: | • Paper jam • Foreign object • Deformation of the Main Frame |
| Remedy: | See Remedy for DC error (CR motor) |
| Error code: | 5BH |
| Description: | Printer: Insoluble paper jam error |
| Causes: | • Paper jam • Foreign object |
| Error code: | 80H |
| Description: | Printer: Circuit error (include blowout of a fuse) |
| Causes: | • Main Board failure |
| Error code: | D1H |
| Description: | PN/AL PID excess load error (Printer) |
| Causes: | • Panel Encoder failure (contaminated/detached scale, Encoder Board failure) • Panel Motor failure • Carriage overload error (paper jam/foreign object) • Cable disconnection |
| Remedy: | • Checking the mechanism and operation: Check the mechanism and operation of the motor in question. • Checking the connection of the connectors and routing of the lead wires • Checking the motor in question and the following parts and replacing the defective part: • Main Board • Power Supply Board |
| Error code: | D2H |
| Description: | PN/AL PID excess speed error (Printer) |
| Causes: | • Panel Encoder failure (contaminated/detached scale, Encoder Board failure) • Motor Driver failure • Tooth skip of the Panel/Stacker gears |
| Remedy: | • Checking the mechanism and operation: Check the mechanism and operation of the motor in question. • Checking the connection of the connectors and routing of the lead wires • Checking the motor in question and the following parts and replacing the defective part: • Main Board • Power Supply Board |
| Error code: | D3H |
| Description: | PN/AL PID reverse error (Printer) |
| Causes: | • Panel Encoder failure (contaminated/detached scale, Encoder Board failure) • Tooth skip of the Panel/Stacker gears • Carriage overload error (paper jam/foreign object) |
| Remedy: | • Checking the mechanism and operation: Check the mechanism and operation of the motor in question. • Checking the connection of the connectors and routing of the lead wires • Checking the motor in question and the following parts and replacing the defective part: • Main Board • Power Supply Board |
| Error code: | D4H |
| Description: | PN/AL PID lock error (Printer) |
| Causes: | • Panel Encoder failure (contaminated/detached scale, Encoder Board failure) • Panel Motor failure • Carriage overload error (paper jam/foreign object) • Cable disconnection |
| Remedy: | • Checking the mechanism and operation: Check the mechanism and operation of the motor in question. • Checking the connection of the connectors and routing of the lead wires • Checking the motor in question and the following parts and replacing the defective part: • Main Board • Power Supply Board |
| Error code: | Displaying |
| Description: | Displaying the Fatal Error Code The fatal error code is stored in the EEPROM on the Main Board and can be read out using the Adjustment Program. The code can be displayed on the LCD of the control panel by a special panel operation. |
| Remedy: | 1. Press the following buttons simultaneously while the fatal error is occurring. • Menu button • Stop button • OK button 2. Check the displayed fatal error code. |
| Error code: | F1H |
| Description: | PF PID excess load error (Printer) |
| Causes: | • PF Encoder failure (contaminated/detached scale, Encoder Board failure) • PF Motor failure • PF drive mechanism overload (paper jam/foreign object) • Cable disconnection |
| Error code: | F2H |
| Description: | PF PID excess speed error (Printer) |
| Causes: | • PF Encoder failure (contaminated/detached scale, Encoder Board failure) • Motor driver failure (Main Board failure) • Tooth skip of the PF Timing Belt • Improper tension of the PF Timing Belt |
| Error code: | F3H |
| Description: | PF PID reverse error (Printer) |
| Causes: | • PF Encoder failure (contaminated/detached scale, Encoder Board failure) • Tooth skip of the PF Timing Belt • Improper tension of the PF Timing Belt |
| Error code: | F4H |
| Description: | PF PID lock error (Printer) |
| Causes: | • PF Encoder failure (contaminated/detached scale, Encoder Board failure) • PF Motor failure • PF drive mechanism overload (paper jam/foreign object) • Cable disconnection |
| Error code: | F8H |
| Description: | PF load position reverse error (Printer) |
| Causes: | • PF Encoder failure (contaminated/detached scale, Encoder Board failure) • Tooth skip of the PF Timing Belt • Improper tension of the PF Timing Belt |
| Error code: | F9H |
| Description: | PF load position excess speed error (Printer) |
| Causes: | • PF Encoder failure (contaminated/detached scale, Encoder Board failure) • Motor driver failure (Main Board failure) • Tooth skip of the PF Timing Belt • Improper tension of the PF Timing Belt |
| Error code: | FAH |
| Description: | PF load position excess load error |
| Causes: | • PF Encoder failure (contaminated/detached scale, Encoder Board failure) • PF Motor failure • PF drive mechanism overload (paper jam/foreign object) • Cable disconnection |
| Remedy: | • Checking the PF mechanism by visual inspection: Check the PF mechanism for paper jam or adhesion of foreign matters by visual inspection. • Checking the operation of the PF mechanism: Operate the PF mechanism by hand, and check to see if it operates smoothly. • Making the following adjustments: • Bi-D • Paper feed length with PF Assy • Paper feed length with Eject Assy • PW adjustment • Checking the following parts and replace the defective one: • Checking the PF Encoder FFC (CN8) for disconnection or breakage • Checking the lead wires of the PF Motor (CN13) for disconnection or breakage • Checking the PF scale for adhesion of dirt or damage • Checking the PF encoder for adhesion of dirt or damage • Checking the Upper Paper Guides for improper installation • Checking the PF Motor and replacing it if necessary • Main Board • Power Supply Board |
