Epson PM260
Рейтинг
Модули
MECH-011
CASE-012
ELEC-011
Детали ELEC-011
| Деталь: | PRINTER MECHANISM,B,ASP |
| Парткод: | 2118714 |
| Деталь: | MOTOR,ASSY.,PF |
| Парткод: | 1464195 |
| Деталь: | POROUS PAD, PAPER GUIDE |
| Парткод: | 1464192 |
| Деталь: | POROUS PAD,PAPER GUIDE,LOWER |
| Парткод: | 1427608 |
| Деталь: | MOTOR,ASSY.,ASF |
| Парткод: | 1464199 |
| Деталь: | POROUS PAD,INK EJECT,UPPER,IS, B |
| Парткод: | 1435153 |
| Деталь: | PRINT HEAD |
| Парткод: | F174010 |
| Деталь: | GROUNDING SPRING,ROLLER,EJ |
| Парткод: | 1427601 |
| Деталь: | CUT WASHER,4.1X0.5X6.5 |
| Парткод: | 1428359 |
| Деталь: | TORSION SPRING,44.9 |
| Парткод: | 1427603 |
| Деталь: | CABLE ASSY.,CR, B |
| Парткод: | 2109959 |
| Деталь: | HOLDER,TUBE,JOINT |
| Парткод: | 1427203 |
| Деталь: | MOTOR,ASSY.,CR |
| Парткод: | 1464189 |
| Деталь: | IS, ASSY., ASP |
| Парткод: | 1436794 |
| Деталь: | PAPER,GUIDE,FRONT,ASSY.,ASP |
| Парткод: | 1473114 |
| Деталь: | SCALE,PF,ASSY.,ASP |
| Парткод: | 1436796 |
| Деталь: | FRAME,CR,ASSY.,ASP |
| Парткод: | 1473113 |
| Деталь: | ASF,ASSY.,ASP |
| Парткод: | 1473112 |
| Деталь: | SCALE,CR,ASSY.,ASP |
| Парткод: | 1436799 |
| Деталь: | DUCT,JOINT,SUPPLY,ASSY.,ASP |
| Парткод: | 1436800 |
| Деталь: | CARTRIDGE,ASSY,B.,ASP |
| Парткод: | 1473178 |
| Деталь: | TRAY ASSY.,ASP |
| Парткод: | 1436811 |
| Деталь: | GUIDE, PAPER EJECT |
| Парткод: | 1464193 |
| Деталь: | CLAMP,TUBE |
| Парткод: | 1436642 |
| Деталь: | BOARD ASSY./ENCODER/PF |
| Парткод: | 2103140 |
| Деталь: | HARNESS,ENCORDER,PF |
| Парткод: | 2116798 |
| Деталь: | COVER,FFC ASSY.ASP |
| Парткод: | 1446872 |
| Деталь: | INK CART.UNBOXED,COL L,DYE, G06C,NA,AS |
| Парткод: | 1452593 |
| Деталь: | INK CART.UNBOXED,COL M,DYE, G06C,SK,AS |
| Парткод: | 1491612 |
| Деталь: | SOFTWARE CD,E/S/P/UK/F/I/G/D |
| Парткод: | 3102484 |
| Деталь: | SETTING UP MANUAL |
| Парткод: | 4110575 |
| Деталь: | USERS GUIDE |
| Парткод: | 4110577 |
| Деталь: | HUNDLE |
| Парткод: | 1463760 |
| Деталь: | BUTTON,MAIN, C |
| Парткод: | 1474146 |
| Деталь: | BUTTON,PW |
| Парткод: | 1463753 |
| Деталь: | BUTTON,PRINT |
| Парткод: | 1463754 |
| Деталь: | FRAME,SLOT,ASSY,B.,ASP |
| Парткод: | 1473192 |
| Деталь: | HOUSING,REAR,ASSY,B.,ASP |
| Парткод: | 1473186 |
| Деталь: | COVER,PRINTER ASSY,E.,ASP |
| Парткод: | 1473179 |
| Деталь: | COVER,LCD |
| Парткод: | 1463983 |
| Деталь: | HOUSING,MIDDLE,ASSY,B.,ASP |
| Парткод: | 1473181 |
| Деталь: | STACKER,ASSY.,ASP |
| Парткод: | 1473189 |
| Деталь: | HOUSING,UPPER,ASSY,B.,ASP |
| Парткод: | 1473184 |
| Деталь: | LCD,ASSY.,ASP |
| Парткод: | 1473190 |
| Деталь: | FOOT |
| Парткод: | 1272694 |
| Деталь: | HOUSING,UPPER,SUPPORT |
| Парткод: | 1463757 |
| Деталь: | POWER CABLE |
| Парткод: | 2107708 |
| Деталь: | AC ADAPTER |
| Парткод: | 2108015 |
Коды ошибок
01
02
03
04
05
06
07
08
09
10
11
12
13
Описание
| Error code: | 01 |
| Display: | ERROR CONDITION INVALID HEAD |
| Description: | The ERROR light flashes. |
| Causes: | The printhead was replaced with one that is not a genuine Zebra™ printhead. |
| Remedy: | Install a genuine Zebra printhead. |
| Error code: | 02 |
| Display: | ERROR CONDITION RIBBON OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
| Remedy: | Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. |
| Error code: | 03 |
| Display: | WARNING RIBBON IN |
| Description: | The ERROR light flashes. |
| Causes: | Ribbon is loaded, but the printer is set for direct thermal mode. |
| Remedy: | Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81. |
| Error code: | 04 |
| Display: | ERROR CONDITION PAPER OUT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded. |
| Remedy: | Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration. |
| Error code: | 05 |
| Display: | ERROR CONDITION HEAD OPEN |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is not fully closed. The head open sensor is not working properly. |
| Remedy: | Replace the sensor. |
| Error code: | 06 |
| Display: | THERMISTOR FAULT |
| Description: | The ERROR light flashes. |
| Causes: | The printhead has a faulty thermistor. |
| Remedy: | Replace the printhead. |
| Error code: | 07 |
| Display: | WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD |
| Description: | The printer stops; the ERROR light is on; the printer cycles through these three messages. |
| Causes: | The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 08 |
| Display: | WARNING HEAD COLD |
| Description: | The printer prints while the ERROR light flashes. |
| Causes: | The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
| Remedy: | Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
| Error code: | 09 |
| Display: | WARNING HEAD TOO HOT |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | The printhead is over temperature. |
| Remedy: | Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature. |
| Error code: | 10 |
| Display: | DEFRAGMENTING |
| Description: | The printer stops. |
| Causes: | The printer is defragmenting memory. |
| Remedy: | Caution • Do NOT turn off the printer power during defragmenting. Doing so can damage the printer. Allow the printer to finish defragmenting. If you get this error message frequently, check your label formats. Formats that write to and erase memory frequently may cause the printer to defragment often. Using properly coded label formats usually minimizes the need for defragmenting. If this error message does not go away, contact Technical Support. The printer requires service. |
| Error code: | 11 |
| Display: | ERROR CONDITION CUTTER JAM |
| Description: | The printer stops; the ERROR light flashes. |
| Causes: | Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers. The cutter blade is in the media path. |
| Remedy: | Turn off the printer power and unplug the printer. Inspect the cutter module for debris and clean as needed following the cleaning instructions in Clean the Cutter Module on page 135. |
| Error code: | 12 |
| Description: | General print quality issues |
| Causes: | The printer is set at the incorrect print speed. You are using an incorrect combination of labels and ribbon for your application. The printer is set at an incorrect darkness level. The printhead is dirty. Incorrect or uneven printhead pressure. The printhead is improperly balanced. |
| Remedy: | For optimal print quality, set the print speed to the lowest possible setting for your application via control panel, the driver, or the software. See Adjust Print Speed on page 79. You may want to perform the FEED Self Test on page 120. 1. Switch to a different type of media or ribbon to try to find a compatible combination. 2. If necessary, consult your authorized Zebra reseller or distributor for information and advice. For optimal print quality, set the darkness to the lowest possible setting for your application via the control panel, the driver, or the software. See Adjust Print Darkness on page 78. You may want to perform the FEED Self Test on page 120 to determine the ideal darkness setting. Clean the printhead. See Clean the Printhead and Platen Roller on page 131. Set the printhead pressure to the minimum needed for good print quality. See Adjust Printhead Pressure on page 70. Adjust the printhead balance. |
| Error code: | 13 |
| Description: | Long tracks of missing print on several labels |
| Causes: | Print element damaged. |
| Remedy: | Replace the printhead. |
Парткод
Название
EPSON T5846 Набор PictureMate (150 листов бумаги 10х15 и четырехцветный картридж)
