Epson SC-T5000
Рейтинг
Модули
MECH-021
CASE-011
MECH-011
ACCE-011
MECH-032
ELEC-011
Детали MECH-021
| Деталь: | HARNESS |
| Парткод: | 2142136 |
| Деталь: | HARNESS |
| Парткод: | 2148220 |
| Деталь: | SHEET,GUIDE PLATE,TUBU,UPPER,36 |
| Парткод: | 1579801 |
| Деталь: | SHEET,GUIDE PLATE, TUBU, MIDDLE,36 |
| Парткод: | 1579802 |
| Деталь: | SHEET,GUIDE PLATE, TUBU, LOWER, 44 |
| Парткод: | 1579797 |
| Деталь: | COVER,CR |
| Парткод: | 1560762 |
| Деталь: | TIMING BELT,PF |
| Парткод: | 1573729 |
| Деталь: | SCALE,CR,36 |
| Парткод: | 1588583 |
| Деталь: | FFC,CSIC,CN5-FULL |
| Парткод: | 2143866 |
| Деталь: | TUBE,INK EJECT |
| Парткод: | 1564338 |
| Деталь: | PRINT HEAD,IC856V |
| Парткод: | FA10000 |
| Деталь: | GUIDE,ROLL PAPER,SUPPORT |
| Парткод: | 1568042 |
| Деталь: | SENSOR ASSY. |
| Парткод: | 2142803 |
| Деталь: | HARNESS |
| Парткод: | 2142120 |
| Деталь: | HARNESS |
| Парткод: | 2142122 |
| Деталь: | HARNESS |
| Парткод: | 2142127 |
| Деталь: | HARNESS |
| Парткод: | 2142131 |
| Деталь: | HARNESS |
| Парткод: | 2142143 |
| Деталь: | HARNESS |
| Парткод: | 2142151 |
| Деталь: | HARNESS |
| Парткод: | 2142152 |
| Деталь: | HARNESS |
| Парткод: | 2142154 |
| Деталь: | BOARD ASSY.,SUB |
| Парткод: | 2144083 |
| Деталь: | COVER,LEVER,ATC,ROLL |
| Парткод: | 1568045 |
| Деталь: | PAD,MAINTENANCE COVER |
| Парткод: | 1564787 |
| Деталь: | LEVER,ATC, ROLL, SUB |
| Парткод: | 1568044 |
| Деталь: | LEVER,ATC,ROLL |
| Парткод: | 1568043 |
| Деталь: | HOUSING,PANEL,LOWER,ASSY,ASP |
| Парткод: | 1588062 |
| Деталь: | COVER,FRONT,ASSY,ASP |
| Парткод: | 1588066 |
| Деталь: | COVER,INNER,LEFT,36 ASSY |
| Парткод: | 1588072 |
| Деталь: | COVER,INNER,RIGHT,36 ASSY |
| Парткод: | 1588074 |
| Деталь: | PAPER GUIDE LOWER ASSY.,ESL,ASP |
| Парткод: | 1588045 |
| Деталь: | PAPER GUIDE LOWER,B,ASSY.,ESL,ASP |
| Парткод: | 1588047 |
| Деталь: | COVER,IH,ASSY,ASP |
| Парткод: | 1588064 |
| Деталь: | HOLDER,IH,ASSY,ASP |
| Парткод: | 1588065 |
| Деталь: | COVER,SIDE,LEFT,UPPER |
| Парткод: | 1552192 |
| Деталь: | COVER,SIDE,ROLL,LEFT |
| Парткод: | 1563166 |
| Деталь: | COVER,FRONT,SUB,LEFT,36 |
| Парткод: | 1563146 |
| Деталь: | COVER,FRONT,SUB,RIGHT,36 |
| Парткод: | 1563147 |
| Деталь: | COVER,FRONT,LEFT |
| Парткод: | 1563158 |
| Деталь: | COVER,FRONT,RIGHT |
| Парткод: | 1563159 |
| Деталь: | COVER,INNER |
| Парткод: | 1563173 |
| Деталь: | COVER,TOP,BASE,36 |
| Парткод: | 1563142 |
| Деталь: | COVER,PRINTER, SUB, LEFT,36 |
| Парткод: | 1563144 |
| Деталь: | COVER,PRINTER, SUB, RIGHT,36 |
| Парткод: | 1563145 |
| Деталь: | COVER,PRINTER |
| Парткод: | 1595275 |
| Деталь: | COVER,SIDE,RIGHT,UPPER |
| Парткод: | 1552189 |
| Деталь: | CAP,CR,ADJUST |
| Парткод: | 1560601 |
| Деталь: | COVER,TOP,RIGHT |
| Парткод: | 1563161 |
| Деталь: | COVER,SIDE,ROLL,RIGHT |
| Парткод: | 1563165 |
| Деталь: | CAP,COVER,REAR |
| Парткод: | 1573788 |
| Деталь: | COVER,ROLL,36 |
| Парткод: | 1563143 |
| Деталь: | COVER,BASE,RIGHT |
| Парткод: | 1563152 |
| Деталь: | COVER,FRONT,LEFT,LOWER |
| Парткод: | 1563153 |
| Деталь: | COVER,BASE,LEFT |
| Парткод: | 1563154 |
| Деталь: | COVER,TOP,LEFT |
| Парткод: | 1563162 |
| Деталь: | COVER,TOP,SUPPORT,RIGHT |
| Парткод: | 1563163 |
| Деталь: | COVER,TANK,INK EJECT |
| Парткод: | 1573784 |
| Деталь: | PAPER GUIDE,LOWER |
| Парткод: | 1573785 |
| Деталь: | COVER,SIDE,RIGHT,LOWER |
| Парткод: | 1573791 |
| Деталь: | COVER,SIDE,LEFT,LOWER |
| Парткод: | 1573792 |
| Деталь: | LABEL,MODEL NAME |
| Парткод: | 1582214 |
| Деталь: | HARNESS |
| Парткод: | 2142136 |
| Деталь: | HARNESS |
| Парткод: | 2148220 |
| Деталь: | SHEET,GUIDE PLATE,TUBU,UPPER,36 |
| Парткод: | 1579801 |
| Деталь: | SHEET,GUIDE PLATE, TUBU, MIDDLE,36 |
| Парткод: | 1579802 |
| Деталь: | SHEET,GUIDE PLATE, TUBU, LOWER, 44 |
| Парткод: | 1579797 |
| Деталь: | COVER,CR |
| Парткод: | 1560762 |
| Деталь: | TIMING BELT,PF |
| Парткод: | 1573729 |
| Деталь: | SCALE,CR,36 |
| Парткод: | 1588583 |
| Деталь: | FFC,CSIC,CN5-FULL |
| Парткод: | 2143866 |
| Деталь: | TUBE,INK EJECT |
| Парткод: | 1564338 |
| Деталь: | PRINT HEAD,IC856V |
| Парткод: | FA10000 |
| Деталь: | GUIDE,ROLL PAPER,SUPPORT |
| Парткод: | 1568042 |
| Деталь: | SENSOR ASSY. |
| Парткод: | 2142803 |
| Деталь: | HARNESS |
| Парткод: | 2142120 |
| Деталь: | HARNESS |
| Парткод: | 2142122 |
| Деталь: | HARNESS |
| Парткод: | 2142127 |
| Деталь: | HARNESS |
| Парткод: | 2142131 |
| Деталь: | HARNESS |
| Парткод: | 2142143 |
| Деталь: | HARNESS |
| Парткод: | 2142151 |
| Деталь: | HARNESS |
| Парткод: | 2142152 |
| Деталь: | HARNESS |
| Парткод: | 2142154 |
| Деталь: | BOARD ASSY.,SUB |
| Парткод: | 2144083 |
| Деталь: | COVER,LEVER,ATC,ROLL |
| Парткод: | 1568045 |
| Деталь: | PAD,MAINTENANCE COVER |
| Парткод: | 1564787 |
| Деталь: | LEVER,ATC, ROLL, SUB |
| Парткод: | 1568044 |
| Деталь: | LEVER,ATC,ROLL |
| Парткод: | 1568043 |
| Деталь: | HARNESS |
| Парткод: | 2142136 |
| Деталь: | HARNESS |
| Парткод: | 2148220 |
| Деталь: | SHEET,GUIDE PLATE,TUBU,UPPER,36 |
| Парткод: | 1579801 |
| Деталь: | SHEET,GUIDE PLATE, TUBU, MIDDLE,36 |
| Парткод: | 1579802 |
| Деталь: | SHEET,GUIDE PLATE, TUBU, LOWER, 44 |
| Парткод: | 1579797 |
| Деталь: | COVER,CR |
| Парткод: | 1560762 |
| Деталь: | TIMING BELT,PF |
| Парткод: | 1573729 |
| Деталь: | SCALE,CR,36 |
| Парткод: | 1588583 |
| Деталь: | FFC,CSIC,CN5-FULL |
| Парткод: | 2143866 |
| Деталь: | TUBE,INK EJECT |
| Парткод: | 1564338 |
| Деталь: | PRINT HEAD,IC856V |
| Парткод: | FA10000 |
| Деталь: | GUIDE,ROLL PAPER,SUPPORT |
| Парткод: | 1568042 |
| Деталь: | SENSOR ASSY. |
| Парткод: | 2142803 |
| Деталь: | HARNESS |
| Парткод: | 2142120 |
| Деталь: | HARNESS |
| Парткод: | 2142122 |
| Деталь: | HARNESS |
| Парткод: | 2142127 |
| Деталь: | HARNESS |
| Парткод: | 2142131 |
| Деталь: | HARNESS |
| Парткод: | 2142143 |
| Деталь: | HARNESS |
| Парткод: | 2142151 |
| Деталь: | HARNESS |
| Парткод: | 2142152 |
| Деталь: | HARNESS |
| Парткод: | 2142154 |
| Деталь: | BOARD ASSY.,SUB |
| Парткод: | 2144083 |
| Деталь: | COVER,LEVER,ATC,ROLL |
| Парткод: | 1568045 |
| Деталь: | PAD,MAINTENANCE COVER |
| Парткод: | 1564787 |
| Деталь: | LEVER,ATC, ROLL, SUB |
| Парткод: | 1568044 |
| Деталь: | LEVER,ATC,ROLL |
| Парткод: | 1568043 |
| Деталь: | STAND,RIGHT,FULL.ASSY.,ESL,ASP |
| Парткод: | 1588075 |
| Деталь: | STAND,LEFT,FULL.ASSY.,ESL,ASP |
| Парткод: | 1588076 |
| Деталь: | HOLDER ,BASKET,R,ASSY.,ASP |
| Парткод: | 1588055 |
| Деталь: | GUIDE,BASKET,LOWER,ASSY.,ASP |
| Парткод: | 1588058 |
| Деталь: | JOINT,BASKET,RIGHT,ASSY,ASP |
| Парткод: | 1588054 |
| Деталь: | SCREW ASSY |
| Парткод: | 1588077 |
| Деталь: | STAND,TOP,RIGHT |
| Парткод: | 1560763 |
| Деталь: | STAND,TOP,LEFT |
| Парткод: | 1560765 |
| Деталь: | CASTER,P-50G |
| Парткод: | 1573820 |
| Деталь: | CASTER,P-50GS |
| Парткод: | 1573821 |
| Деталь: | PIPE,BASKET,36 |
| Парткод: | 1573848 |
| Деталь: | BASKET,36 |
| Парткод: | 1573850 |
| Деталь: | PIPE,STOPPER,PAPER GUIDE,BASKET,36 |
| Парткод: | 1573852 |
| Деталь: | JOINT,BASKET,LEFT |
| Парткод: | 1573773 |
| Деталь: | HANDLE, STOPPER, PAPER GUIDE,BASKET |
| Парткод: | 1573780 |
| Деталь: | HOLDER ,BASKET,L,ASSY.,ASP |
| Парткод: | 1588057 |
| Деталь: | HARNESS |
| Парткод: | 2142136 |
| Деталь: | HARNESS |
| Парткод: | 2148220 |
| Деталь: | SHEET,GUIDE PLATE,TUBU,UPPER,36 |
| Парткод: | 1579801 |
| Деталь: | SHEET,GUIDE PLATE, TUBU, MIDDLE,36 |
| Парткод: | 1579802 |
| Деталь: | SHEET,GUIDE PLATE, TUBU, LOWER, 44 |
| Парткод: | 1579797 |
| Деталь: | COVER,CR |
| Парткод: | 1560762 |
| Деталь: | TIMING BELT,PF |
| Парткод: | 1573729 |
| Деталь: | SCALE,CR,36 |
| Парткод: | 1588583 |
| Деталь: | FFC,CSIC,CN5-FULL |
| Парткод: | 2143866 |
| Деталь: | TUBE,INK EJECT |
| Парткод: | 1564338 |
| Деталь: | PRINT HEAD,IC856V |
| Парткод: | FA10000 |
| Деталь: | GUIDE,ROLL PAPER,SUPPORT |
| Парткод: | 1568042 |
| Деталь: | SENSOR ASSY. |
| Парткод: | 2142803 |
| Деталь: | HARNESS |
| Парткод: | 2142120 |
| Деталь: | HARNESS |
| Парткод: | 2142122 |
| Деталь: | HARNESS |
| Парткод: | 2142127 |
| Деталь: | HARNESS |
| Парткод: | 2142131 |
| Деталь: | HARNESS |
| Парткод: | 2142143 |
| Деталь: | HARNESS |
| Парткод: | 2142151 |
| Деталь: | HARNESS |
| Парткод: | 2142152 |
| Деталь: | HARNESS |
| Парткод: | 2142154 |
| Деталь: | BOARD ASSY.,SUB |
| Парткод: | 2144083 |
| Деталь: | COVER,LEVER,ATC,ROLL |
| Парткод: | 1568045 |
| Деталь: | PAD,MAINTENANCE COVER |
| Парткод: | 1564787 |
| Деталь: | LEVER,ATC, ROLL, SUB |
| Парткод: | 1568044 |
| Деталь: | LEVER,ATC,ROLL |
| Парткод: | 1568043 |
| Деталь: | INK CART.BOXED,PBK,PIGT |
| Парткод: | 1589111 |
| Деталь: | INK CART.BOXED,C,PIGT |
| Парткод: | 1589112 |
| Деталь: | INK CART.BOXED,M,PIGT |
| Парткод: | 1589113 |
| Деталь: | INK CART.BOXED,Y,PIGT |
| Парткод: | 1589114 |
| Деталь: | INK CART.BOXED,MBK,PIGT |
| Парткод: | 1589115 |
| Деталь: | GREASE G-26 (40GR)(B702600001) |
| Парткод: | 1080614 |
| Деталь: | PAPER THICKNESS POSITION TOOL |
| Парткод: | 1282355 |
| Деталь: | SONIC TENSION METER U507 |
| Парткод: | 1294120 |
| Деталь: | P-THICK SENSOR POSITION JIG |
| Парткод: | 1424364 |
| Деталь: | GREASE G-71(BLUE) |
| Парткод: | 1480655 |
| Деталь: | GREASE,G-84 |
| Парткод: | 1516265 |
| Деталь: | OIL,O-17 |
| Парткод: | 1521154 |
| Деталь: | GREASE,G-81 |
| Парткод: | 1574337 |
| Деталь: | CLEANING CARTRIDGE |
| Парткод: | 1582821 |
Коды ошибок
0001
0002
1101
1125
1138
1139
113A
113B
113C
113D
113E
113F
1219
122A
122B
122C
122D
122E
122F
131B
1412
1416
1418
1419
141A
141B
141C
141D
141E
141F
14B0
14C0
150C
1519
151A
151B
151C
151D
151E
151F
1523
1530
1539
153A
153B
153C
153D
153E
153F
1540
1541
1548
1549
154A
154B
154C
154D
154E
154F
1551
1561
1599
159A
159B
159C
159D
159E
159F
1620
1621
1622
1623
1900
1A23
1A26
1A37
1A38
1A39
1A41
1A50
1A51
1A70
1A71
1A72
1F11
1F80 ... 1FC3
1FE0
1FE1
1FE2
1FE3
2000
2002
2003
2008
200A
200D
3000
Dxxy
Fxxx
Описание
| Error code: | 0001 |
| Display: | Main motor failure CODE (001) Turn power off, on |
| Description: | Main Motor Failure The Main Motor lock signal remains HIGH for a predetermined consecutive period of time while the Main Motor remains energized. |
| Causes: | • Main Motor, PL9.1.6 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check the Engine Control Board connector P/J8. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Check the Main Motor for proper positioning. Is the motor engaged with the gears? Go to step 3. Reseat the motor drive properly. If the problem persists, go to step 3. 3 Check the operation of the Main Motor. Is the motor faulty? Replace the motor. If the problem persists, go to step 4. Go to step 4. 4 On the Engine Control Board, check P/J2 at pins 1, 5, and 7 for +24V. Are the voltages present? Go to step 5. Go to step 6. 5 Replace the Engine Control Board. Does the problem persist? Go to step 5. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0002 |
| Description: | Disorder of communication with Sub CPU This occurs when the Sub CPU is not detected after turning on the machine |
| Causes: | Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. |
| Remedy: | Check cable connection between Main Board and Servo Board. Check cable connection between Main Board and Heater Board. Check the other cable connections of Servo Board Heater Board replacement Servo Board replacement Main Board replacement Flexible cable replacement |
| Error code: | 1101 |
| Display: | Replace part soon. |
| Description: | Data transmission did not finish within the specified time. |
| Causes: | An incompatible loop-back connector is connected to the parallel port, or the loop-back connector is not connected. Use the correct loop-back connector (P/#: G0219350) before the test. |
| Remedy: | Load paper. If the problem remains, then check the paper sensor. |
| Error code: | 1125 |
| Description: | CR HP detection error The CR HP SENSOR cannot detect the CR UNIT. Or the CR UNIT cannot detect the touching surface for the home position setting, so the home position cannot be set. • CR HP SENSOR failure • False detection of the home due to paper jam or any other obstacle • Misreading of CR SCALE • CR Lock is damaged. |
| Causes: | The CR HP SENSOR cannot detect the CR UNIT. Or the CR UNIT cannot detect the touching surface for the home position setting, so the home position cannot be set. • CR HP SENSOR failure • False detection of the home due to paper jam or any other obstacle • Misreading of CR SCALE • CR Lock is damaged. |
| Remedy: | 1. Replace the CR HP SENSOR. 2. Re-install the CR ENCODER. If it is faulty, replace it. 3. Clean the CR SCALE using ethanol. 4. Replace the CR SCALE. 5. Replace the CR Lock . |
| Error code: | 1138 |
| Description: | Over current error Connection failure of the CR MOTOR or the CR ENCODER. • The number of occurrences of overcurrent to the CR MOTOR has reached a predetermined limit. • Irregular load • CR ENCODER failure • CR MOTOR failure |
| Causes: | • Connection failure of the CR MOTOR or the CR ENCODER. • The number of occurrences of overcurrent to the CR MOTOR has reached a predetermined limit. • Irregular load • CR ENCODER failure • CR MOTOR failure |
| Remedy: | 1. Replace the CR ENCODER. 2. Replace the CR MOTOR. |
| Error code: | 1139 |
| Description: | Oscillation error The control terminal (Vre terminal) of the CR MOTOR driver has shorted out. |
| Causes: | The control terminal (Vre terminal) of the CR MOTOR driver has shorted out. |
| Remedy: | 1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 113A |
| Description: | Overload error Overcurrent to the CR MOTOR was detected. • CR ENCODER cable is damaged. • CR MOTOR cable is damaged. • Irregular load • CR ENCODER failure • CR MOTOR failure |
| Causes: | Overcurrent to the CR MOTOR was detected. • CR ENCODER cable is damaged. • CR MOTOR cable is damaged. • Irregular load • CR ENCODER failure • CR MOTOR failure |
| Remedy: | 1. Re-install the CR UNIT. 2. Replace the CR ENCODER. 3. Replace the CR MOTOR. |
| Error code: | 113B |
| Description: | Over speed error The CR MOTOR was driven at a speed faster than a predetermined one during deceleration. • Irregular load • CR ENCODER failure • SUB BOARD is damaged. • CR MOTOR driver failure |
| Causes: | The CR MOTOR was driven at a speed faster than a predetermined one during deceleration. • Irregular load • CR ENCODER failure • SUB BOARD is damaged. • CR MOTOR driver failure |
| Remedy: | 1. Replace the CR ENCODER. 2. Replace the SUB BOARD. 3. Replace the MAIN BOARD. |
| Error code: | 113C |
| Description: | Reversing error The number of occurrences of reversing the CR MOTOR has reached a predetermined limit. • The polarity of CR ENCODER cable is opposite. • The polarity of CR MOTOR cable is opposite. • Slipping of the teeth of CR TIMING BELT • CR ENCODER failure |
| Causes: | The number of occurrences of reversing the CR MOTOR has reached a predetermined limit. • The polarity of CR ENCODER cable is opposite. • The polarity of CR MOTOR cable is opposite. • Slipping of the teeth of CR TIMING BELT • CR ENCODER failure |
| Remedy: | 1. Adjust the tension of the CR TIMING BELT. 2. Replace the CR ENCODER. |
| Error code: | 113D |
| Description: | Driving time-out error Abnormally-long driving duration of the CR MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Causes: | Abnormally-long driving duration of the CR MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 113E |
| Description: | Velocity deviation error The CR MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • CR ENCODER failure • CR MOTOR failure • SUB BOARD is damaged. • CR MOTOR driver failure |
| Causes: | The CR MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • CR ENCODER failure • CR MOTOR failure • SUB BOARD is damaged. • CR MOTOR driver failure |
| Remedy: | 1. Replace the CR ENCODER. 2. Replace the CR MOTOR. 3. Replace the SUB BOARD. 4. Replace the MAIN BOARD. |
| Error code: | 113F |
| Description: | Lock error The CR MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • CR ENCODER cable is damaged. • CR MOTOR cable is damaged. • Irregular load • CR ENCODER failure • CR MOTOR failure |
| Causes: | The CR MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • CR ENCODER cable is damaged. • CR MOTOR cable is damaged. • Irregular load • CR ENCODER failure • CR MOTOR failure |
| Remedy: | 1. Replace the CR ENCODER. 2. Replace the CR MOTOR. |
| Error code: | 1219 |
| Description: | Undefined Signal Error Microprocessor has encountered a bad signal (other than an abort, illegal instruction, or arithmetic exception). |
| Remedy: | Unplug the All-In-One from the wall outlet; wait a few seconds, then plug the All-In- One back in and turn the power on. If the problem remains, then replace the USB cable. Service: Replace the system board. |
| Error code: | 122A |
| Description: | Overload error Overcurrent to the PF MOTOR was detected. • PF ENCODER cable is damaged. • PF MOTOR cable is damaged. • Irregular load • PF ENCODER failure • PF MOTOR failure |
| Causes: | Overcurrent to the PF MOTOR was detected. • PF ENCODER cable is damaged. • PF MOTOR cable is damaged. • Irregular load • PF ENCODER failure • PF MOTOR failure |
| Remedy: | 1. Replace the PF ENCODER. 2. Replace the MAIN BOARD. |
| Error code: | 122B |
| Description: | Over speed error The PF MOTOR was driven at a speed faster than a predetermined one during deceleration. • PF irregular load • PF ENCODER failure • SUB-B BOARD is damaged. • PF MOTOR driver failure |
| Causes: | The PF MOTOR was driven at a speed faster than a predetermined one during deceleration. • PF irregular load • PF ENCODER failure • SUB-B BOARD is damaged. • PF MOTOR driver failure |
| Remedy: | 1. Replace the PF ENCODER. 2. Replace the SUB-B BOARD. 3. Replace the MAIN BOARD. |
| Error code: | 122C |
| Description: | Reversing error The number of occurrences of reversing the PF MOTOR has reached a predetermined limit. • The polarity of PF ENCODER cable is opposite. • The polarity of PF MOTOR cable is opposite. • Slipping of the teeth of PF TIMING BELT • PF ENCODER failure |
| Causes: | The number of occurrences of reversing the PF MOTOR has reached a predetermined limit. • The polarity of PF ENCODER cable is opposite. • The polarity of PF MOTOR cable is opposite. • Slipping of the teeth of PF TIMING BELT • PF ENCODER failure |
| Remedy: | 1. Adjust the tension of the PF TIMING BELT. 2. Replace the PF ENCODER. |
| Error code: | 122D |
| Description: | Driving time-out error Abnormally-long driving duration of the PF MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Causes: | Abnormally-long driving duration of the PF MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 122E |
| Description: | Velocity deviation error The PF MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • PF ENCODER failure • PF MOTOR failure • SUB BOARD is damaged. • PF MOTOR driver failure |
| Causes: | The PF MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • PF ENCODER failure • PF MOTOR failure • SUB BOARD is damaged. • PF MOTOR driver failure |
| Remedy: | 1. Replace the PF ENCODER. 2. Replace the PF MOTOR. 3. Replace the MAIN BOARD. |
| Error code: | 122F |
| Description: | Lock error The PF MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • PF ENCODER cable disconnection • PF MOTOR cable disconnection • Irregular load • PF ENCODER failure • PF MOTOR failure |
| Causes: | The PF MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • PF ENCODER cable disconnection • PF MOTOR cable disconnection • Irregular load • PF ENCODER failure • PF MOTOR failure |
| Remedy: | 1. Replace the PF ENCODER. 2. Replace the PF MOTOR. |
| Error code: | 131B |
| Description: | Head driver (transmission gate) overheat error The temperature of the Head driver rises, and has reached a predetermined limit. |
| Causes: | The temperature of the Head driver rises, and has reached a predetermined limit. |
| Remedy: | 1. Replace the HEAD FFC. 2. Replace the PRINT HEAD. |
| Error code: | 1412 |
| Description: | Pump life error The number of PUMP CAP UNIT operation has reached the specified limit. (The rotation of the pump motor has reached the specified limit.) |
| Causes: | The number of PUMP CAP UNIT operation has reached the specified limit. (The rotation of the pump motor has reached the specified limit.) |
| Remedy: | Replace the PUMP CAP UNIT , and reset its counter . |
| Error code: | 1416 |
| Description: | Undetermined position error PUMP CAP UNIT failure |
| Causes: | PUMP CAP UNIT failure |
| Remedy: | Replace the PUMP CAP UNIT . |
| Error code: | 1418 |
| Description: | Overcurrent error Connection failure of the pump motor or the pump motor encoder. • The number of occurrences of overcurrent to the pump motor has reached a predetermined limit. • Irregular load • pump motor encoder failure • pump motor failure |
| Causes: | • Connection failure of the pump motor or the pump motor encoder. • The number of occurrences of overcurrent to the pump motor has reached a predetermined limit. • Irregular load • pump motor encoder failure • pump motor failure |
| Remedy: | Replace the pump motor encoder and pump motor . |
| Error code: | 1419 |
| Description: | Oscillation error The control terminal (Vre terminal) of the pump motor driver has shorted out. |
| Causes: | The control terminal (Vre terminal) of the pump motor driver has shorted out. |
| Remedy: | 1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 141A |
| Description: | Overload error Overcurrent to the pump motor was detected. • Pump motor encoder cable disconnection • Pump motor cable disconnection • Irregular load • Pump motor encoder failure • Pump motor failure |
| Causes: | Overcurrent to the pump motor was detected. • Pump motor encoder cable disconnection • Pump motor cable disconnection • Irregular load • Pump motor encoder failure • Pump motor failure |
| Remedy: | Replace the pump motor encoder and pump motor . |
| Error code: | 141B |
| Description: | Over speed error The pump motor was driven at a speed faster than a predetermined one during deceleration. • Irregular load • Pump motor encoder failure • Pump motor driver failure |
| Causes: | The pump motor was driven at a speed faster than a predetermined one during deceleration. • Irregular load • Pump motor encoder failure • Pump motor driver failure |
| Remedy: | 1. Replace the pump motor encoder . 2. Replace the MAIN BOARD. |
| Error code: | 141C |
| Description: | Reversing error The number of occurrences of reversing the pump motor has reached a predetermined limit. • The polarity of pump motor encoder cable is opposite. • The polarity of pump motor cable is opposite. |
| Causes: | The number of occurrences of reversing the pump motor has reached a predetermined limit. • The polarity of pump motor encoder cable is opposite. • The polarity of pump motor cable is opposite. |
| Remedy: | Replace the pump motor encoder . |
| Error code: | 141D |
| Description: | Driving time-out error Abnormally-long driving duration of the pump motor was detected. • Irregular load • Firmware becomes out of control. |
| Causes: | Abnormally-long driving duration of the pump motor was detected. • Irregular load • Firmware becomes out of control. |
| Remedy: | Replace the MAIN BOARD. the |
| Error code: | 141E |
| Description: | Velocity deviation error The pump motor was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • Pump motor encoder failure • Pump motor failure • Pump motor driver failure |
| Causes: | The pump motor was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • Pump motor encoder failure • Pump motor failure • Pump motor driver failure |
| Remedy: | 1. Replace the pump motor encoder and pump motor . 2. Replace the MAIN BOARD. |
| Error code: | 141F |
| Description: | Lock error The pump motor was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • Pump motor encoder failure • Pump motor failure |
| Causes: | The pump motor was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • Pump motor encoder failure • Pump motor failure |
| Remedy: | Replace the pump motor encoder and pump motor . |
| Error code: | 14B0 |
| Description: | Life of the pump in the ink path (IC HOLDER life error) The IC HOLDER has reached its end of specified life. (The number of detaching ink cartridges has reached a predetermined limit.) |
| Causes: | The number of IC HOLDER operation has reached the specified limit. (The motion of the pump in the ink path has reached the specified limit.) |
| Remedy: | Replace the IC HOLDER. and reset its counter . |
| Error code: | 14C0 |
| Description: | DAMPER KIT error The DAMPER KIT has reached its end of specified life |
| Causes: | The DAMPER KIT has reached its end of specified life. |
| Remedy: | Replace the DAMPER KIT and reset its counter . |
| Error code: | 150C |
| Description: | PG position undetectable error When changing the PG, the PG SENSOR could not detect the PG position. |
| Causes: | When changing the PG, the PG SENSOR could not detect the PG position. |
| Remedy: | 1. Replace the PG SENSOR. 2. Replace the APG UNIT. 3. Remove any obstacles around the CR UNIT home position. The printer changes the PG with the CR UNIT being at its home position. |
| Error code: | 1519 |
| Description: | Oscillation error The control terminal (Vre terminal) of the APG motor driver has shorted out. |
| Causes: | The control terminal (Vre terminal) of the APG motor driver has shorted out. |
| Remedy: | 1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 151A |
| Description: | Overload error Connection failure of the APG motor. • Overcurrent to the APG motor was detected. • APG motor cable is damaged. • Irregular load • APG encoder failure • APG motor failure |
| Causes: | • Connection failure of the APG motor. • Overcurrent to the APG motor was detected. • APG motor cable is damaged. • Irregular load • APG encoder failure • APG motor failure |
| Remedy: | Replace the APG UNIT. |
| Error code: | 151B |
| Description: | Over speed error The APG motor was driven at a speed faster than a predetermined one during deceleration. • Irregular load • APG encoder failure • APG motor driver failure |
| Causes: | The APG motor was driven at a speed faster than a predetermined one during deceleration. • Irregular load • APG encoder failure • APG motor driver failure |
| Remedy: | 1. Replace APG UNIT. 2. Replace the MAIN BOARD. |
| Error code: | 151C |
| Description: | Reversing error The number of occurrences of reversing the APG motor has reached a predetermined limit. • The polarity of APG motor cable is opposite. • APG motor failure |
| Causes: | The number of occurrences of reversing the APG motor has reached a predetermined limit. • The polarity of APG motor cable is opposite. • APG motor failure |
| Remedy: | Replace APG UNIT. |
| Error code: | 151D |
| Description: | Driving time-out error Detects that the driving period is irregularly long. • Irregular load • Firmware becomes out of control. |
| Causes: | Detects that the driving period is irregularly long. • Irregular load • Firmware becomes out of control. |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 151E |
| Description: | Velocity deviation error The APG motor was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • APG encoder failure • APG motor failure • APG motor driver failure |
| Causes: | The APG motor was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • APG encoder failure • APG motor failure • APG motor driver failure |
| Remedy: | 1. Replace APG UNIT. 2. Replace the MAIN BOARD. |
| Error code: | 151F |
| Description: | Lock error Connection failure of the APG motor. • The APG motor was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • APG encoder failure • APG motor failure |
| Causes: | • Connection failure of the APG motor. • The APG motor was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • APG encoder failure • APG motor failure |
| Remedy: | Replace APG UNIT. |
| Error code: | 1523 |
| Description: | Roll sensor error |
| Causes: | • Connection failure of the PE SENSOR (Roll Paper). • The lever of the PE SENSOR (Roll Paper) does not work correctly or dropped off. • PE SENSOR (Roll Paper) failure |
| Remedy: | TBD |
| Error code: | 1530 |
| Description: | PF heater 2 high temperature error (paper feeder 2) A temperature higher than 75C/167F is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Shorted PF thermistor 2. Defective PF fan motor 2. Defective PF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 2 and PF main PWB (YC111) Shorted PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder). Defective PF fan motor 2. Replace the side heater unit (Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1539 |
| Description: | Oscillation error The control terminal (Vre terminal) of the PRESSURE ROLLER MOTOR driver has shorted out. |
| Causes: | The control terminal (Vre terminal) of the PRESSURE ROLLER MOTOR driver has shorted out. |
| Remedy: | 1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 153A |
| Description: | Overload error Overcurrent to the PRESSURE ROLLER MOTOR was detected. • PRESSURE ROLLER SENSOR cable is damaged. • PRESSURE ROLLER MOTOR cable is damaged. • Irregular load • PRESSURE ROLLER MOTOR encoder failure • PRESSURE ROLLER MOTOR failure |
| Causes: | Overcurrent to the PRESSURE ROLLER MOTOR was detected. • PRESSURE ROLLER SENSOR cable is damaged. • PRESSURE ROLLER MOTOR cable is damaged. • Irregular load • PRESSURE ROLLER MOTOR encoder failure • PRESSURE ROLLER MOTOR failure |
| Remedy: | Replace the PRESSURE ROLLER MOTOR. |
| Error code: | 153B |
| Description: | Over speed error The PRESSURE ROLLER MOTOR was driven at a speed faster than a predetermined one during deceleration. • Irregular load • PRESSURE ROLLER SENSOR failure • PRESSURE ROLLER MOTOR driver failure |
| Causes: | The PRESSURE ROLLER MOTOR was driven at a speed faster than a predetermined one during deceleration. • Irregular load • PRESSURE ROLLER SENSOR failure • PRESSURE ROLLER MOTOR driver failure |
| Remedy: | 1. Replace the PRESSURE ROLLER SENSOR. 2. Replace the MAIN BOARD. |
| Error code: | 153C |
| Description: | Reversing error The number of occurrences of reversing the PRESSURE ROLLER MOTOR has reached a predetermined limit. • The polarity of PRESSURE ROLLER MOTOR encoder cable is opposite. • The polarity of PRESSURE ROLLER MOTOR cable is opposite. |
| Causes: | The number of occurrences of reversing the PRESSURE ROLLER MOTOR has reached a predetermined limit. • The polarity of PRESSURE ROLLER MOTOR encoder cable is opposite. • The polarity of PRESSURE ROLLER MOTOR cable is opposite. |
| Remedy: | Replace the PRESSURE ROLLER MOTOR encoder cable/ PRESSURE ROLLER MOTOR. |
| Error code: | 153D |
| Description: | Driving time-out error Abnormally-long driving duration of the PRESSURE ROLLER MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Causes: | Abnormally-long driving duration of the PRESSURE ROLLER MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 153E |
| Description: | Velocity deviation error The PRESSURE ROLLER MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • PRESSURE ROLLER MOTOR encoder failure • PRESSURE ROLLER MOTOR failure • PRESSURE ROLLER MOTOR driver failure |
| Causes: | The PRESSURE ROLLER MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • PRESSURE ROLLER MOTOR encoder failure • PRESSURE ROLLER MOTOR failure • PRESSURE ROLLER MOTOR driver failure |
| Remedy: | 1. Replace the PRESSURE ROLLER MOTOR encoder cable/PRESSURE ROLLER MOTOR. 2. Replace the MAIN BOARD. |
| Error code: | 153F |
| Description: | Lock error The PRESSURE ROLLER MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • PRESSURE ROLLER MOTOR encoder failure • PRESSURE ROLLER MOTOR failure |
| Causes: | The PRESSURE ROLLER MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • PRESSURE ROLLER MOTOR encoder failure • PRESSURE ROLLER MOTOR failure |
| Remedy: | Replace the PRESSURE ROLLER MOTOR encoder cable/ PRESSURE ROLLER MOTOR. |
| Error code: | 1540 |
| Description: | PF heater 1 high temperature error (paper feeder 3) A temperature higher than 75C/167F is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Shorted PF thermistor 1. Defective PF fan motor 1. Defective PF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 1 and PF main PWB (YC111) Shorted PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder). Defective PF fan motor 1. Replace the top heater unit (Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1541 |
| Description: | Cutter return error |
| Causes: | The Cutter cannot return to its home position. • Slipping of the teeth of the Cutter Timing Belt • CUTTER HOME POSITION SENSOR failure |
| Remedy: | TBD |
| Error code: | 1548 |
| Description: | Oscillation error The control terminal (Vre terminal) of the cutter motor driver has shorted out. |
| Causes: | The control terminal (Vre terminal) of the cutter motor driver has shorted out. |
| Remedy: | 1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 1549 |
| Description: | Motor disconnection error |
| Causes: | • Connection between the SUB-B BOARD and the MAIN BOARD has an abnormality. • The CUTTER UNIT operation is not detected. • Irregular load • CUTTER MOTOR Assy cable is damaged. • CUTTER MOTOR ENCORDER failure. • CUTTER MOTOR failure |
| Remedy: | TBD |
| Error code: | 154A |
| Description: | Overload error Overcurrent to the cutter motor was detected. • Cutter motor encoder cable is damaged. • Cutter motor cable is damaged. • Irregular load • Cutter motor encoder failure • Cutter motor failure |
| Causes: | Overcurrent to the CUTTER MOTOR was detected. • CUTTER MOTOR ENCORDER cable is damaged. • CUTTER MOTOR cable is damaged. • Irregular load • CUTTER MOTOR ENCORDER failure • CUTTER MOTOR failure |
| Remedy: | Replace the cutter motor/cutter motor encoder (CUTTER UNIT). |
| Error code: | 154B |
| Description: | Over speed error The cutter motor was driven at a speed faster than a predetermined one during deceleration. • Irregular load • Cutter motor encoder failure • Cutter motor driver failure |
| Causes: | The CUTTER MOTOR was driven at a speed faster than a predetermined one during deceleration. • Irregular load • CUTTER MOTOR ENCORDER failure • CUTTER MOTOR driver failure |
| Remedy: | 1. Replace the cutter motor encoder (CUTTER UNIT). 2. Replace the SUB-B BOARD. 3. Replace the MAIN BOARD. |
| Error code: | 154C |
| Description: | Reversing error The number of occurrences of reversing the cutter motor has reached a predetermined limit. • The polarity of cutter motor encoder cable is opposite. • The polarity of cutter motor cable is opposite. |
| Causes: | The number of occurrences of reversing the CUTTER MOTOR has reached a predetermined limit. • The polarity of CUTTER MOTOR ENCORDER cable is opposite. • The polarity of CUTTER MOTOR cable is opposite. |
| Remedy: | Replace the cutter motor/cutter motor encoder (CUTTER UNIT). |
| Error code: | 154D |
| Description: | Driving time-out error Abnormally-long driving duration of the cutter motor was detected. • Irregular load • Firmware becomes out of control. |
| Causes: | Abnormally-long driving duration of the CUTTER MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 154E |
| Description: | Velocity deviation error The cutter motor was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • Cutter motor encoder failure • Cutter motor failure • Cutter motor driver failure |
| Causes: | The CUTTER MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • CUTTER MOTOR ENCORDER failure • CUTTER MOTOR failure • CUTTER MOTOR driver failure |
| Remedy: | 1. Replace the cutter motor encoder (CUTTER UNIT). 2. Replace the SUB-B BOARD. 3. Replace the MAIN BOARD. |
| Error code: | 154F |
| Description: | Lock error The cutter motor was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • Cutter motor encoder failure • Cutter motor failure |
| Causes: | The CUTTER MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • CUTTER MOTOR ENCORDER failure • CUTTER MOTOR failure |
| Remedy: | Replace the cutter motor/cutter motor encoder (CUTTER UNIT). |
| Error code: | 1551 |
| Description: | Paper Thickness Sensor error |
| Causes: | • During detection of paper thickness, the thickness cannot be determined because the sensor is not stable due to vibration or the like. • The PAPER THICKNESS SENSOR is damaged and cannot detect the paper thickness correctly. |
| Remedy: | TBD |
| Error code: | 1561 |
| Description: | Paper thickness at power-on error |
| Causes: | At power-on, the PAPER THICKNESS SENSOR detects more than 2.2mm paper thickness. |
| Remedy: | TBD |
| Error code: | 1599 |
| Description: | Oscillation error The control terminal (Vre terminal) of the ATC MOTOR driver has shorted out. |
| Causes: | The control terminal (Vre terminal) of the ATC MOTOR driver has shorted out. |
| Remedy: | 1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 159A |
| Description: | Overload error Overcurrent to the ATC MOTOR was detected. • ATC MOTOR cable disconnection. • Irregular load • ATC MOTOR encoder failure • ATC MOTOR failure |
| Causes: | Overcurrent to the ATC MOTOR was detected. • ATC MOTOR cable disconnection. • Irregular load • ATC MOTOR encoder failure • ATC MOTOR failure |
| Remedy: | Replace the ATC MOTOR. |
| Error code: | 159B |
| Description: | Over speed error The ATC Motor was driven at a speed faster than a predetermined one during deceleration. • Irregular load • ATC MOTOR encoder failure • APG MOTOR driver failure |
| Causes: | The ATC MOTOR was driven at a speed faster than a predetermined one during deceleration. • Irregular load • ATC MOTOR encoder failure • APG MOTOR driver failure |
| Remedy: | 1. Replace the ATC MOTOR. 2. Replace the MAIN BOARD. |
| Error code: | 159C |
| Description: | Reversing error The number of occurrences of reversing the ATC Motor has reached a predetermined limit. • The polarity of ATC MOTOR cable is opposite. • ATC MOTOR failure |
| Causes: | The number of occurrences of reversing the ATC MOTOR has reached a predetermined limit. • The polarity of ATC MOTOR cable is opposite. • ATC MOTOR failure |
| Remedy: | Replace the ATC MOTOR. |
| Error code: | 159D |
| Description: | Driving time-out error Abnormally-long driving duration of the ATC MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Causes: | Abnormally-long driving duration of the ATC MOTOR was detected. • Irregular load • Firmware becomes out of control. |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 159E |
| Description: | Velocity deviation error The ATC MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • ATC MOTOR encoder failure • ATC MOTOR failure • ATC MOTOR driver failure |
| Causes: | The ATC MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • ATC MOTOR encoder failure • ATC MOTOR failure • ATC MOTOR driver failure |
| Remedy: | 1. Replace the ATC MOTOR. 2. Replace the MAIN BOARD. |
| Error code: | 159F |
| Description: | Lock error Connection failure of the ATC MOTOR. • The ATC MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • ATC MOTOR encoder failure • ATC MOTOR failure |
| Causes: | • Connection failure of the ATC MOTOR. • The ATC MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • Irregular load • ATC MOTOR encoder failure • ATC MOTOR failure |
| Remedy: | Replace the ATC MOTOR. |
| Error code: | 1620 |
| Description: | PF heater 1 low temperature error (paper feeder 2) An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on. |
| Causes: | Defective connector cable or poor contact in the connector. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. Broken PF heater 1. Defective PF heater PWB or PF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 1 and PF heater PWB (YC1) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 1 and PF main PWB (YC114) PF thermistor 1 installed incorrectly. Check the installation of the PF thermistor 1. Defective PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder). Broken PF heater 1. Replace the top heater unit (Refer to the service manual for the paper feeder). Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1621 |
| Description: | Pressurizing/Suction switching error The pressurizing and suction processes did not complete within a predetermined time period. |
| Causes: | The pressurizing and suction processes did not complete within a predetermined time period. |
| Remedy: | 1. Replace the pressure unit (IC HOLDER). 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 1622 |
| Description: | Operating time-out error The switching operation did not complete within a predetermined time period. |
| Causes: | The switching operation did not complete within a predetermined time period. |
| Remedy: | 1. Replace the pressure unit (IC HOLDER). 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 1623 |
| Description: | Continuous revolution error The control terminal (Vre terminal) of the pressure motor driver has shorted out. |
| Causes: | The control terminal (Vre terminal) of the pressure motor driver has shorted out. |
| Remedy: | 1. Remove the foreign materials. 2. If the error still occurs, replace the MAIN BOARD. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1A23 |
| Description: | Incorrect RTC data error The various absolute time settings stored on the NVRAM are abnormal. |
| Causes: | The various absolute time settings stored on the NVRAM are abnormal. |
| Remedy: | If the error still occurs after resetting the date and time, perform the followings. 1. Replace the RTC backup battery. 2. Replace the MAIN BOARD. |
| Error code: | 1A26 |
| Description: | RTC Access T/O error The RTC circuit on the MAIN BOARD malfunctions |
| Causes: | The RTC circuit on the MAIN BOARD malfunctions. |
| Remedy: | 1. Turn the power off and remove the RTC backup battery. 2. After several seconds, re-attach the battery and turn the power back on. 3. Reset the date and time settings of the RTC using the Service Program. |
| Error code: | 1A37 |
| Description: | Thermistor error The HEAD FFC is not connected correctly. • A temperature out of a predetermined range was detected by the Head thermistor. • Head thermistor failure |
| Causes: | • The HEAD FFC is not connected correctly. • A temperature out of a predetermined range was detected by the Head thermistor. • Head thermistor failure |
| Remedy: | 1. Replace the HEAD FFC. 2. Replace the PRINT HEAD. |
| Error code: | 1A38 |
| Description: | Transistor environmental temperature error Transistor failure • A temperature out of a predetermined range was detected by the Head thermistor. |
| Causes: | • Transistor failure • A temperature out of a predetermined range was detected by the Head thermistor. |
| Remedy: | Replace the PRINT HEAD. |
| Error code: | 1A39 |
| Description: | Head error Connection failure of the HEAD FFC. • Electric parts or components are damaged due to improper HEAD FFC connection such as connecting it at an angle. • The drive circuit in the PRINT HEAD is damaged. • The fuse of the MAIN BOARD has blown. |
| Causes: | • Connection failure of the HEAD FFC. • Electric parts or components are damaged due to improper HEAD FFC connection such as connecting it at an angle. • The drive circuit in the PRINT HEAD is damaged. • The fuse of the MAIN BOARD has blown. |
| Remedy: | 1. Replace the HEAD FFC. 2. Replace the PRINT HEAD. 3. Replace the MAIN BOARD. |
| Error code: | 1A41 |
| Description: | Head rank ID input error An invalid Head rank ID was written to the NVRAM. |
| Causes: | An invalid Head rank ID was written to the NVRAM. |
| Remedy: | Rewrite the Head rank ID with a correct one. |
| Error code: | 1A50 |
| Description: | I2C communication error (Between elements on ASIC and MAIN) An I2C communication error has occurred in the MAIN BOARD |
| Causes: | An I2C communication error has occurred in the MAIN BOARD. |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 1A51 |
| Description: | I2C communication error (Between elements on ASIC and SUB) An I2C communication error between the MAIN BOARD and SUB BOARD has occurred. |
| Causes: | An I2C communication error between the MAIN BOARD and SUB BOARD has occurred. |
| Remedy: | 1. Replace the FFC between the MAIN BOARD and SUB BOARD. 2. Replace the SUB BOARD. 3. Replace the MAIN BOARD. |
| Error code: | 1A70 |
| Description: | MAIN-to-MAIN-B BOARD communication error |
| Remedy: | TBD |
| Error code: | 1A71 |
| Description: | MAIN-B BOARD system error (Core0) |
| Remedy: | TBD |
| Error code: | 1A72 |
| Description: | MAIN-B BOARD system error (Core1) |
| Remedy: | TBD |
| Error code: | 1F11 |
| Description: | Maintenance 2 (for safety standard) |
| Remedy: | TBD |
| Error code: | 1F80 ... 1FC3 |
| Description: | CSIC error |
| Remedy: | 1. Replace the IC HOLDER. 2. Replace the MAIN BOARD. |
| Error code: | 1FE0 |
| Description: | Controlled domain full error |
| Causes: | • Running out of disk space of the controlled domain for print job on the optional HDD Unit. • Integration value of print jobs reached the maximum of the controlled domain on the optional HDD Unit. |
| Remedy: | TBD |
| Error code: | 1FE1 |
| Description: | Invalid lock |
| Causes: | • Optional HDD Unit failure • Non-support HDD Unit was attached to the printer |
| Remedy: | TBD |
| Error code: | 1FE2 |
| Description: | Device access error |
| Causes: | Optional HDD Unit failure |
| Remedy: | TBD |
| Error code: | 1FE3 |
| Description: | Missing device |
| Causes: | • Connection failure of the optional HDD Unit • Communication error between the optional HDD Unit and the printer |
| Remedy: | TBD |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 2002 |
| Description: | Printer controller: FGATE error Printer application returned FGATE error notification to copier. |
| Causes: | • FGATE error |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 2003 |
| Description: | FLASH BOOT SUM CHECK error Installing the firmware has failed. • The Flash ROM is out of order. |
| Causes: | • Installing the firmware has failed. • The Flash ROM is out of order. |
| Remedy: | 1. Re-install the firmware. 2. Replace the MAIN BOARD. |
| Error code: | 2008 |
| Description: | Wrong FLASH device error |
| Causes: | Fixing Delivery Sensor Stationary |
| Remedy: | TBD |
| Error code: | 200A |
| Display: | Paper size not detected. Press Load/Eject and reload the paper. Paper size not detected. Reload paper. Paper size not detected. Press OK and reload the paper. |
| Description: | F/W load error Reading/decompressing the firmware has failed. |
| Causes: | Reading / decompressing the firmware has failed. |
| Remedy: | 1. Re-install the firmware. 2. Replace the MAIN BOARD. |
| Error code: | 200D |
| Description: | System interrupt watchdog time-out error A system failure such as CPU failure, or defective cash has occurred. |
| Causes: | A system failure such as CPU failure, or defective cash has occurred. |
| Remedy: | Replace the MAIN BOARD. |
| Error code: | 3000 |
| Description: | Main Motor`s failure to turn • The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning. |
| Causes: | The AC power has been shut off due to a power failure, unplugged, PSH BOARD failure, or MAIN BOARD failure or the like. |
| Remedy: | 1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the PWB-M connector for proper connection and correct as necessary. 4 M1 operation check PWB-M CNDM1-5 (REM) PWB-M CNDM1-8 (LOCK) K to L-2. 5 Change PWB-M. 6 Change PU1. |
| Error code: | Dxxy |
| Description: | Service call for FW debugging This error is intended to be used in the product development stage. It is supposed to not occur to marketed products, but may occur due to an unexpected cause such as external noises. |
| Causes: | This error is intended to be used in the product development stage. It is supposed to not occur to marketed products, but may occur due to an unexpected cause such as external noises. |
| Remedy: | 1. Re-install the firmware. 2. Replace the MAIN BOARD. |
| Error code: | Fxxx |
| Description: | CPU related service call There is something wrong with the firmware |
| Causes: | There is something wrong with the firmware. |
| Remedy: | 1. Re-install the firmware. 2. Replace the MAIN BOARD. |
