HP Color LaserJet 4550n

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

35000

Цветность печати

цветная

Общие характеристики
Макс. формат	A4
Цветность печати	цветная
Размещение	настольный
Тип устройства	Принтер
Телефон
Копир
Сканер
Факс
Печать фотографий
Число страниц в месяц	35 000
Тип	лазерный/светодиодный
Технология печати	лазерная
Область применения	малый офис
Принтер
Количество цветов	4
Прямая печать
Пигментные чернила
Печать без полей
Двусторонняя печать
Макс, разрешение для ч/б печати
По Y	600
По X	600
Скорость цветной печати
A4	4
Расходные материалы
Ресурс цветного картриджа/тонера	6 000
Количество картриджей	4
Ресурс ч/б картриджа/тонера	9 000
Печать на:
Этикетках
Матовой бумаге
Карточках
Пленках
Конвертах
Глянцевой бумаге
Фотобумаге
Рулоне
CD/DVD
Телефон
Стандарт DECT
АОН
Caller ID
Беспроводная трубка
Автоответчик
Проводная трубка
Спикерфон
Языки управления
PostScript
PostScript 3
PostScript 2
Лотки
Подача бумаги
Стандартная	400
Вывод бумаги
Стандартный	350
Финишер
Сортер
Сортировка со сдвигом
Степлер
Брошюровщик
Электронная сортировка
Интерфейсы
Ethernet (RJ-45)
LPT
Инфракрасный порт
Wi-Fi
USB
Bluetooth
RS-232
FireWire (IEEE 1394)
Устройство для чтения карт памяти
Память/Процессор
Макс, объем памяти	256
Объем памяти	64
Дополнительная информация
Экран
Мин. системные требования
Поддержка ОС
Mac OS
Windows
Linux
DOS
Уровень шума
При работе	56
Габариты
Вес	51
Глубина	570
Ширина	500
Высота	390

Модули

(Электронные компоненты)

Детали None

Коды ошибок

13.0

13.1

41.3

41.5

50.7

50.x

53.XY.ZZ

54.1

54.2

54.3

54.4

54.5

54.6

57.1

57.2

57.3

62.X

Описание

Парткод

Название

HP Тонер-картридж черный

HP Тонер-картридж голубой

HP Тонер-картридж пурпурный

HP Тонер-картридж желтый

HP Блок фотобарабана

HP Комплект аппарата переноса

HP Печка в сборе

Деталь:	Formatter, exchange, HP Color LaserJet 3000dn and 3000dtn Series only (256 MB)
Парткод:	C4227-69002

Error code:	13.0
Display:	13.0 Jam
Description:	Media is jammed in the front part of the printer immediately after it is picked up.
Remedy:	1. Check to see if the white plastic tabs (located inside the front of the trays under the separation tabs) have fallen off in Tray 2 or Tray 3. (Note the position of the springs.) 2. Make sure that the correct media is loaded properly in Tray 3, and that it is not overloaded. 3. Make sure that the two shipping locks have been removed from the back of Tray 3. 4. Inspect the pick-up rollers for Tray 2; the flat side of the “D” on the rollers should be parallel to the paper. 5. Make sure that the roller spring underneath the front of Tray 2 is secure.

Error code:	13.1
Display:	13.1 Jam
Description:	A jam has occurred inside the ITB drawer area. (The ITB drawer is also referred to as the middle front drawer for end users.) The jam might be located in the fuser area or between the transfer area and the fuser.
Remedy:	1. Open the ITB drawer and carefully inspect for any media. 2. Be sure to inspect the fusing area. You might need to access the fusing area through the rear door. 3. Remove any jammed media. 4. Make sure that the transfer roller is securely in place.

Error code:	20
Description:	Vertical image or label drift
Causes:	The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media.
Remedy:	Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation.

Error code:	22
Description:	Loss of printing registration on labels. Excessive vertical drift in top-of-form registration.
Causes:	The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly.
Remedy:	Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58.

Error code:	40
Display:	Scanner locked
Description:	10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run.
Causes:	1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors.
Remedy:	Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board.

Error code:	49
Display:	Tray 1 Paper Empty
Description:	There is no paper in the tray 1.
Causes:	Pressure roller thermistor, pressure roller lamp connector, MCU
Remedy:	Load paper in the tray 1.

Error code:	51
Display:	Send Error (DNS)
Description:	Rear Fan Failure The Rear Fan rotation signal indicates the fan is no longer operational.
Causes:	• Rear Fan, PL1.1.19 • LVPS, PL9.1.6 • Engine Control Board, PL9.1.16 • LV Harness, PL10.1.2
Remedy:	1 Check the Rear Fan for damage. Remove the Rear Cover. Is the fan damaged? Replace the Rear Fan. Go to Step 2. 2 Check the Rear Fan connection. Is P/J166 connected to the harness? Go to Step 3. Connect the Fan. 3 Check orientation of the Rear Fan. Does the Fan’s label face inwards? Go to Step 4. Correct the installation. 4 Test the Rear Fan. Run the Service Diagnostics Rear Fan test. Does the fan operate? Go to Step 6. Go to Step 5. 5 Check for +24 V to the fan. Disconnect P/J166. Is there +24 V across P166-1 <=> P166-3? Replace the Rear Fan. Replace the LVPS. 6 Check the fan rotation signal to the LVPS. Print one sheet. Is there +3.3 V between P/J166-1 <=> P/J166-3? Replace the Fuser Fan. Go to Step 7. 7 Check the rotation signal from the LVPS. Print one sheet. Is there +3.3 V between P/J165-15 <=> P/J165-3? Replace the LVPS. Go to Step 8. 8 Check the fan rotation signal at the Engine Control Board. Print one sheet. Is there +3.3 V between P/J61-4 <=> P/J61-16? Replace the LV Harness Replace the Engine Control Board.

Error code:	52
Display:	Send Error (POP3)
Description:	Fan Failure One of the two fans has failed resulting in a fatal error.
Causes:	• Rear Fan, PL1.1.19 • Fuser Fan, PL5.3.31
Remedy:	1 Check the fans for damage or debris: • Fuser Fan, PL1.1.19 • Rear Fan, PL5.3.31 Is either fan damaged? Replace the defective fan. Go to Step 3. 2 Replace the defective fan. Does the error persist? Go to Step 3 Complete 3 Test the fans. Run the Service Diagnostics fan tests to isolate the defective fan. Did one of the fans fail? Go to the troubleshooting procedure for the specific fan. If both fans pass, replace the Engine Control Board.

Error code:	55
Display:	[Stop Pressed]
Description:	Stop/Clear has been pressed during a fax transmission.
Causes:	· Loose cable connection · Defective fusing unit fan · Defective IOD1 board · Defective MCTL board
Remedy:	Try again.

Error code:	62
Display:	Nongenuine Toner Replace Toner
Description:	The toner cartridge installed is not a genuine cartridge.
Causes:	· Loose cable connection · Defective development clutch for magenta · Defective IOD2 board · Defective MCTL board
Remedy:	This message appears when you selected stop at the Non Genuine Toner prompt. Install the genuine toner cartridge.

Error code:	68
Display:	TOP FAN MOTOR LOCK ERROR
Description:	Orange light on An error has occurred at the top fan.
Causes:	Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure.
Remedy:	1) Check the harness connected between the Engine controller and the exit board. (If the harness is out, insert it to the connector.) 2) Check the harness connected between the exit board and the top fan. (If the harness is out, insert it to the connector.) 3) In the Engine diagnostic mode, operate the top fan to check the fan is operating. (If it is not operating, replace the top fan.) 4) Check the No. 1 pin of the exit board whether 24V is outputted and check the D5 whether it is normal. (If 24V is not outputted or the part is abnormal, replace the exit board.) 5) Replace the Engine controller.

Error code:	80
Display:	ERROR 80 FORMAT
Description:	Engine Logic Board Failure, Code 80
Remedy:	1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete Replace the engine control board or the image processor board.

Error code:	50.x
Display:	50.x Fuser Error
Description:	Fuser Error The product has experienced an error with the fuser.
Remedy:	Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. Turn off the product, wait at least 25 minutes, and then turn on the product. If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.

Error code:	53.XY.ZZ
Display:	53.XY.ZZ CHECK RAM DIMM SLOT <X>
Description:	There is a problem with the product memory. The DIMM that caused the error will not be used. Values of X and Y are as follows: • X = DIMM type, 0 = ROM, 1 = RAM • Y = DIMM location, 0 = Internal memory (ROM or RAM), 1 = DIMM slot 1
Remedy:	Press OK to continue if you are prompted. If the message continues, you might need to replace the specified DIMM. Turn the product off, and then replace the DIMM that caused the error.

Error code:	54.2
Display:	54.2 CAROUSEL ERROR CYCLE POWER
Description:	Indicates that the color toner carousel is not working correctly. This could be caused by an obstruction in the carousel path, such as a loose shutter or disengaged toner cartridge.
Remedy:	1 Turn the printer off and on to reset the printer. 2 Open the carousel door and waste toner tray. Look for an obstruction, such as a toner cartridge shutter catching on the waste toner tray. Verify the toner lock lever is fully locked. If the message does not clear after closing the doors, turn the printer off and on to reset the printer. 3 Clean the carousel position sensor (PS3) with compressed air. If the problem persists, replace the sensor. 4 Reconnect connector J701 on carousel motor PCA; connectors J641, J642, J644, and J648 on the main relay PCA; connector J672 on the subrelay PCA; and connector J102 on the power supply. 5 Check operation of the carousel stopper arm. Replace the carousel stopper solenoid. 6 Check electrical continuity between connector J641-1 (+24 VB) and J642-3 (PMP) on the main relay PCA when the door switch (SW641) is turned on. If there is no electrical continuity, replace the main relay PCA. 7 Check electrical continuity between connector J644-1 (PBK) and J644-2 (PMP) on the main relay PCA when the door switch (SW644) is turned on. If there is no electrical continuity, replace the black toner cartridge on/off switch. 8 Check electrical continuity between connector J642-1 (PYMC) and J642-2 (PBK) on the subrelay PCA when the door switch (SW673) is turned on. If there is no electrical continuity, replace the toner cartridge cover switch in the subrelay PCA. 9 Check electrical continuity between connector J642-1 (PYMC) and J648-1 (+24 VAR) on the main relay PCA when the door switch (SW642) is turned on. If there is no electrical continuity, replace the main relay PCA. 10 Measure the voltage across connector J648-1 (+24 VAR) and J648-3 (GND) on the main relay PCA after the printer is turned on. If the voltage is not 24 V, replace the main relay PCA. 11 Reconnect connectors J704 and J706 on the carousel motor PCA, and connector J220 on the controller board. 12 Reconnect connector J43 on the carousel position sensor, relay connector J42 and connector J207 on the controller board. 13 Measure the voltage across connector J220- A6 (RLSROT) and J220-B5 (GND) on the controller board after the printer is turned on. If the voltage changes to about 3.5 V from 0 V, replace the carousel motor PCA. 14 Replace the carousel motor (M1). 15 Replace the controller board.

Error code:	54.3
Display:	54.3 CALIBRATION WARNING PRESS GO TO CONTINUE
Description:	The process marks in the density sensing pattern are corrupted (see chapter 5 for more information).
Remedy:	1 Press GO. 2 Print a configuration page and troubleshoot as an image-quality problem. 3 Check the transfer guide for cracks and replace the transfer guide as needed.

HP Color LaserJet 4550n

Общие характеристики

Макс. формат

Цветность печати

Размещение

Тип устройства

Телефон

Копир

Сканер

Факс

Печать фотографий

Число страниц в месяц

Тип

Технология печати

Область применения

Принтер

Количество цветов

Прямая печать

Пигментные чернила

Печать без полей

Двусторонняя печать

Макс, разрешение для ч/б печати

Скорость цветной печати

Расходные материалы

Ресурс цветного картриджа/тонера

Количество картриджей

Ресурс ч/б картриджа/тонера

Печать на:

Телефон

Стандарт DECT

АОН

Caller ID

Беспроводная трубка

Автоответчик

Проводная трубка

Спикерфон

Языки управления

Лотки

Подача бумаги

Вывод бумаги

Финишер

Сортер

Сортировка со сдвигом

Степлер

Брошюровщик

Электронная сортировка

Интерфейсы

Ethernet (RJ-45)

LPT

Инфракрасный порт

Wi-Fi

USB

Bluetooth

RS-232

FireWire (IEEE 1394)

Устройство для чтения карт памяти

Память/Процессор

Макс, объем памяти

Объем памяти

Дополнительная информация

Экран

Мин. системные требования

Поддержка ОС

Уровень шума

Габариты

Вес

Глубина

Ширина

Высота

Модули

Детали None

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку