HP Color LaserJet 4730xs mfp

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

175000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Макс. формат	A4
Печать фотографий
Телефон
Цветность печати	цветная
Сканер
Тип устройства	МФУ
Копир
Факс
Область применения	большой офис
Размещение	напольный
Технология печати	лазерная
Тип	лазерный/светодиодный
Число страниц в месяц	175 000
Принтер
Пигментные чернила
Печать без полей
Двусторонняя печать
Прямая печать
Макс, разрешение для ч/б печати
По Y	600
По X	600
Скорость ч/б печати
A4	30
Время выхода первого отпечатка
Цветн,	10
Ч/б	10
Копир
Макс, количество копий за цикл	999
Время выхода первой копии	11
Шаг масштабирования	0,01
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По X	600
По Y	600
По Y	300
По X	300
Сканер
Макс. формат оригинала	A4
Устройство автоподачи оригиналов	одностороннее
Стандарт TWAIN
Стандарт WIA
Оттенки серого	256
Тип сканера	планшетный/протяжный
Емкость устройства автоподачи оригиналов	50
Глубина цвета	30 бит
Макс, размер сканирования
По X	216
По Y	356
Разрешение сканера
По Y (улучшенное)	600
По Х	600
По Х (улучшенное)	600
Расходные материалы
Количество картриджей	1
Печать на:
Рулоне
Фотобумаге
CD/DVD
Глянцевой бумаге
Карточках
Матовой бумаге
Конвертах
Пленках
Этикетках
Плотность бумаги
Минимальная	60
Максимальная	220
Факс
PC Fax
Цветной
Макс, скорость передачи данных	33,6 Кбит/с
Телефон
АОН
Caller ID
Автоответчик
Проводная трубка
Спикерфон
Стандарт DECT
Беспроводная трубка
Языки управления
PostScript 2
PCL 5e
PPDS
PCL 5c
PDF
PostScript
PCL 6
PostScript 3
Лотки
Подача бумаги
Максимальная	1 600
Стандартная	1 600
Вывод бумаги
Максимальный	700
Стандартный	500
Финишер
Сортер
Сортировка со сдвигом
Брошюровщик
Степлер
Электронная сортировка
Интерфейсы
Wi-Fi
Инфракрасный порт
RS-232
Bluetooth
FireWire (IEEE 1394)
Версия USB	2,0
USB
LPT
Устройство для чтения карт памяти
Ethernet (RJ-45)
Количество свободных слотов расширения	1
Поддержка карт памяти
CompactFlash
Память/Процессор
Процессор	MIPS 20KC
Частота процессора	533
Емкость жесткого диска	20
Объем памяти	256
Макс, объем памяти	512
Дополнительная информация
Экран
Мин. системные требования
Поддержка ОС
DOS
Windows
Linux
Mac OS
Потребляемая мощность
При работе	604
В режиме ожидания	24
Габариты
Ширина	1 106
Высота	1 153
Глубина	639
Вес	136

Коды ошибок

10.90.XY

10.92.YY

10.XX.YY

11.X

13.01.00

13.02.00

13.05.00

13.12.00

13.31.00

13.JJ.NT

13.XX.YY

30.00.01

30.1

30.1.10

30.1.6

30.1.8

41.3

41.5

44.1

49.XX.XX

50.X

51.1Y

51.2Y

52.XY

53.XY.ZZ

54.X

55.XX.YY

56.XX

57.0X

58.0X

59.XY

60.X

65.X.X

66.XX.YY

68.X

69.X

8X.YYYY

Описание

Парткод

Название

HP Картридж со скрепками

HP 644A Тонер-картридж черный

HP 644A Тонер-картридж голубой

HP 644A Тонер-картридж желтый

HP 644A Тонер-картридж пурпурный

HP Комплект термозакрепления 220V

HP Комплект аппарата переноса изображений

Error code:	10.90.XY
Display:	10.90.XY REPLACE <COLOR> CARTRIDGE
Description:	A toner replenishment malfunction has occurred.
Remedy:	Replace the print cartridge. If replacing the print cartridge does not fix the problem, replace the corresponding image drum.

Error code:	10.92.YY
Display:	10.92.YY CARTRIDGES NOT ENGAGED
Description:	The print cartridge is not seated properly in the MFP. Y=0: Black Y=1: Cyan Y=2: Magenta Y=3: Yellow
Remedy:	1. Remove and reinstall the print cartridge. 2. Ensure that the ETB is installed.

Error code:	10.XX.YY
Display:	10.XX.YY SUPPLY MEMORY ERROR
Description:	An error has occurred in one or more of the product`s supplies. Values of XX and YY are listed below: XX00 = memory is defective XX01 = memory is missing YY00 = cartridge
Remedy:	• Turn the product off and then on to clear the message. • Replace the print cartridge.

Error code:	11.X
Display:	11.X INTERNAL CLOCK ERROR
Description:	This message is displayed when there is a problem with the real-time clock on the formatter board. XX=01 Dead clock battery XX=02 Dead real-time clock
Remedy:	Replace the formatter assembly.

Error code:	13.01.00
Display:	13.01.00 Jam in Tray 1
Description:	The Tray 1 pickup roller or solenoid might not be working correctly.
Remedy:	1. Load paper in Tray 1, and then use the paper path test to pull paper. Verify that the roller rotates. 2. If someone has performed maintenance on the product recently, verify that the Tray 1 pickup roller, feed roller, and separation roller have been installed correctly. 3. From the DIAGNOSTICS menu, run the multipurpose tray (Tray 1) solenoid component test to verify that the solenoid moves when energized. Listen for an audible “click” when the test is initiated. If the solenoid is not being energized, verify that the solenoid connector is attached to connector J71 on the DC controller PCA. 4. If the error persists, replace the Tray 1 solenoid (SL102).

Error code:	20
Description:	Vertical image or label drift
Causes:	The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media.
Remedy:	Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation.

Error code:	22
Description:	Loss of printing registration on labels. Excessive vertical drift in top-of-form registration.
Causes:	The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly.
Remedy:	Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58.

Error code:	40
Display:	Scanner locked
Description:	10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run.
Causes:	1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors.
Remedy:	Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board.

Error code:	62
Display:	Nongenuine Toner Replace Toner
Description:	The toner cartridge installed is not a genuine cartridge.
Causes:	· Loose cable connection · Defective development clutch for magenta · Defective IOD2 board · Defective MCTL board
Remedy:	This message appears when you selected stop at the Non Genuine Toner prompt. Install the genuine toner cartridge.

Error code:	13.02.00
Display:	13.02.00 Jam inside upper right door
Description:	Stay jam at SR5 (top/registration sensor). SR5 continues to detect media, after the media is originally detected, longer than specified.
Remedy:	Clear the jam. 1. Check for paper or other obstructions to the paper path in Tray 2 and before the registration area. 2. Check SR5 (top/registration sensor) and flag for correct mechanical functionality. Repair or replace if necessary. 3. Check connector J319 on the dc controller. 4. Replace the HVPS. 5. Replace the dc controller.

Error code:	13.05.00
Display:	13.05.00 JAM INSIDE TOP COVER
Description:	Paper failed to reach the delivery sensor within a specified period of time when a print job was initiated. When troubleshooting paper jams, always observe where the leading edge of the paper stops in the jam.
Remedy:	1. Verify that nothing is obstructing paper movement within the paper path. 2. Verify that the fuser motor (M2) connector is firmly seated. The fuser motor wiring is hard-wired to the back of the ECU at connector J501. The motor connector is free-standing behind the ECU. To see if the fuser motor is functional, observe the output stacker rollers while turning on the device. If the rollers rotate, the motor is functional. If they do not rotate, verify the connection.

Error code:	30.1.10
Display:	30.1.10 Scan failure
Description:	The product has experienced an ADF fan error.
Remedy:	- Verify that the fan is not functioning while the product is turned on. - Check for loose connections and broken, frayed, or pinched wires. - Reseat the fan connector at scanner control PCA location J109, and connector J156 on the ADF fan. - Replace the ADF fan. - Replace the SCB.

Error code:	49.XX.XX
Display:	49.<XX>.<XX> Error To continue turn off then on
Description:	A critical firmware error has occurred. This type of error can be caused by invalid print commands, corrupt data, or invalid firmware operations. In many cases, turning the product off and turning it on permanently clears the error, and the product continues without issues. In some cases, electrical noise over the cables can corrupt data during transmission. Faulty USB cables, poor connections, and specific software issues can also cause these errors. The formatter can also cause these errors; however such an error is usually a 79 code. Replacing the formatter rarely solves repetitive 49 errors.
Remedy:	- Turn the product off, and then on. - Upgrade the firmware. - Try printing from a different software application to determine whether the application is causing the problem. Go back to the original application an try printing a different file. If the problem seems to be with the software application, contact the vender. Try the following actions: 1. Disconnect all connections to networks and computers. 2. Turn the product off. 3. Remove the DIMM. 4. Remove all EIO devices. 5. Turn the product on. 6. If error disappears, reinstall the EIO devices one at a time to see if the error returns (turn the product off, install the EIO device, and turn it on). If the error returns replace the faulty EIO device. 7. If the error still does not reappear, reconnect each connection to computers or networks until the error reappears. 8. Replace the component that causes the error message.