HP Color LaserJet CM6030f
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
200000
Скорость печати
A4
31
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Печать фотографий |
|
Телефон |
|
Размещение |
напольный |
Область применения |
большой офис |
Макс. формат |
A3 |
Цветность печати |
цветная |
Сканер |
|
Факс |
|
Тип устройства |
МФУ |
Копир |
|
Число страниц в месяц |
200 000 |
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Принтер |
|
Двусторонняя печать |
|
Прямая печать |
|
Печать без полей |
|
Пигментные чернила |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
| По X | 1 200 |
| По Y | 600 |
Скорость ч/б печати |
|
| A4 | 31 |
Время выхода первого отпечатка |
|
| Цветн, | 15,8 |
| Ч/б | 15,5 |
Копир |
|
Макс, количество копий за цикл |
999 |
Значение масштаба |
|
| Минимальное | 0,25 |
| Максимальное | 4 |
Макс, разрешение (ч/б) |
|
| По X | 600 |
| По Y | 600 |
| По Y | 300 |
| По X | 300 |
Сканер |
|
Емкость устройства автоподачи оригиналов |
50 |
Тип сканера |
планшетный/протяжный |
Макс. формат оригинала |
A3 |
Глубина цвета |
30 бит |
Устройство автоподачи оригиналов |
двустороннее |
Слайд-адаптер |
|
Тип датчика сканера |
ПЗС (CCD) |
Отправка изображения по e-mail |
|
Макс, размер сканирования |
|
| По Y | 432 |
| По X | 297 |
Разрешение сканера |
|
| По Х | 600 |
Скорость сканирования |
|
| Ч/б | 40 |
Расходные материалы |
|
Количество картриджей |
4 |
Ресурс цветного картриджа/тонера |
21 000 |
Ресурс ч/б картриджа/тонера |
19 500 |
Печать на: |
|
| Карточках |
|
| Конвертах |
|
| Этикетках |
|
| Пленках |
|
| Матовой бумаге |
|
| Глянцевой бумаге |
|
| Фотобумаге |
|
| Рулоне |
|
| CD/DVD |
|
Плотность бумаги |
|
| Минимальная | 60 |
| Максимальная | 220 |
Факс |
|
Цветной |
|
Макс, скорость передачи данных |
33,6 Кбит/с |
PC Fax |
|
Телефон |
|
Стандарт DECT |
|
Проводная трубка |
|
Спикерфон |
|
Caller ID |
|
АОН |
|
Автоответчик |
|
Беспроводная трубка |
|
Языки управления |
|
| PPDS |
|
| PostScript |
|
| PostScript 2 |
|
| PCL 6 |
|
| PostScript 3 |
|
| PCL 5e |
|
|
|
|
| PCL 5c |
|
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Стандартная | 2 100 |
| Максимальная | 2 100 |
Вывод бумаги |
|
| Стандартный | 500 |
| Максимальный | 1 600 |
Финишер |
|
Электронная сортировка |
|
Брошюровщик |
|
Степлер |
|
Сортер |
|
Интерфейсы |
|
Версия USB |
2,0 |
Количество слотов расширения |
1 |
Количество свободных слотов расширения |
1 |
Wi-Fi |
|
Инфракрасный порт |
|
RS-232 |
|
Bluetooth |
|
Устройство для чтения карт памяти |
|
LPT |
|
FireWire (IEEE 1394) |
|
Веб-интерфейс |
|
USB |
|
Ethernet (RJ-45) |
|
Память/Процессор |
|
Макс, объем памяти |
768 |
Частота процессора |
835 |
Емкость жесткого диска |
80 |
Объем памяти |
512 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Мин. системные требования |
Intel Pentium II |
Экран |
|
Поддержка ОС |
|
| DOS |
|
| Mac OS |
|
| Windows |
|
Потребляемая мощность |
|
| В режиме ожидания | 23 |
| При работе | 920 |
Уровень шума |
|
| В режиме ожидания | 40,3 |
| При работе | 57,1 |
Габариты |
|
Высота |
988 |
Глубина |
673 |
Ширина |
704 |
Модули
Input-tray main body (1x500-sheet)
Saddle paper-delivery assembly (booklet-maker)
Printer multi-purpose-tray assembly
Printer external covers and panels
Printer duplexing-feed assembly
Intermediate-feed upper-guide assembly
Output bin 1 (stack upper-tray assembly) (1 of 2) (booklet-maker)
Top output bin (stack sub-tray assembly) (stapler/stacker)
Return-roller assembly (stapler/stacker and booklet-maker)
Saddle-tray assembly (booklet-maker)
SCANNER UNIT
Jam-cover assembly
Printer internal components (4 of 7)
Saddle assembly (2 of 4) (booklet-maker)
Intermediate-feed lower-guide assembly
Printer duplexing-reverse assembly
Paper-feeder motor assembly (stapler/stacker and booklet-maker)
Printer internal components (6 of 7)
Pressure-roller assembly (stapler/stacker and booklet-maker)
Operation-tray assembly (1 of 2) (stapler/stacker and booklet-maker)
Saddle assembly (1 of 4) (booklet-maker)
ADF unit
Printer internal components (5 of 7)
Havic assembly
Input-tray cassette
Printer lifter-drive assembly
Printer internal components (7 of 7)
Fan-system assembly
External panels and covers (stapler/stacker)
Transmission assembly
Output bin 2 (stack lower-tray assembly) (2 of 2) (stapler/stacker and booklet-maker)
Printer internal components (1 of 7)
Scanner controller-board (SCB) assembly
Output bin 1 (stack upper-tray assembly) (2 of 2) (stapler/stacker)
Finisher (3 of 5) (stapler/stacker and booklet-maker)
Input-tray paper-pickup assembly
Plastic-parts assembly (1 of 2)
Booklet-maker unit
Large-pin assembly
Small-pin assembly
Printer face-down paper-delivery assembly
Entrance upper-guide assembly (stapler/stacker and booklet-maker)
Support-frame assembly
Glass assembly
Operation-tray assembly (2 of 2) (stapler/stacker and booklet-maker)
Pulley assembly
Inverter assembly
Printer right-door assembly
Power-supply assembly
Input-tray auto-close assembly
Finisher (4 of 5) (stapler/stacker and booklet-maker)
Saddle-stapler assembly (booklet-maker)
Backbone assembly
Saddle-guide assembly (booklet-maker)
Printer PCA assembly location
Lid-sensor assembly
Plastic-parts assembly (2 of 2)
Output bin 1 (stack upper-tray assembly) (1 of 2) (stapler/stacker)
Output bin 2 (stack lower-tray assembly) (1 of 2) (stapler/stacker and booklet-maker)
Printer cassette paper-pickup assembly
Finisher (5 of 5) (stapler/stacker and booklet-maker)
Saddle assembly (4 of 4) (booklet-maker)
Carriage Assembly
Printer multi-purpose-drive assembly
Staple assembly (stapler/stacker and booklet-maker)
Scanner controller board (SCB)-cage assembly
Left-assist assembly
Stapler/stacker unit
Saddle paper-feeder assembly (stapler/stacker)
Pass lower-guide assembly (booklet-maker)
Printer internal components (3 of 7)
Input-tray main body (3x500-sheet)
Motor assembly
Swing-guide assembly (stapler/stacker and booklet-maker)
External panels and covers (booklet-maker)
Hinge assembly
PCA assembly
Printer front-door assembly
Printer multi-purpose paper-pickup assembly
Input-tray PCA assembly
Output bin 1 (stack upper-tray assembly) (2 of 2) (booklet-maker )
Saddle paper-feeder assembly (booklet-maker)
Finisher (2 of 5) (stapler/stacker and booklet-maker)
Input-tray units (1x500-sheet and 3x500-sheet)
Printer internal components (2 of 7)
Right-assist assembly
Inner side-plate assembly (booklet-maker)
Finisher (1 of 5) (stapler/stacker and booklet-maker)
Saddle assembly (3 of 4) (booklet-maker)
Main-frame assembly
Motor-mount assembly (booklet-maker)
Front-end cover
Separation-pad assembly
Intermediate-feed main body
Separation-floor assembly
Pickup-roller assembly
Printer cassette
Base assembly
Printer multi-purpose-guide assembly
Детали Input-tray main body (3x500-sheet)
| Деталь: | COVER, REAR |
| Парткод: | RC1-9871-000CN |
| Деталь: | COVER, LEFT |
| Парткод: | RC1-9872-000CN |
| Деталь: | Cover, front-upper |
| Парткод: | RC1-9873-000CN |
| Деталь: | Cover, right-lower |
| Парткод: | RC1-9874-000CN |
| Деталь: | Guide, paper-feed roller |
| Парткод: | RC1-9881-000CN |
| Деталь: | Stopper, right-door |
| Парткод: | RC1-9882-000CN |
| Деталь: | LEVER, LOCK |
| Парткод: | RC1-9883-000CN |
| Деталь: | Tape, door |
| Парткод: | RC1-9884-000CN |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-1331-000CN |
| Цена: | 2 500 ₽ |
| Деталь: | Cover, right-front |
| Парткод: | RL1-1322-000CN |
| Деталь: | SCREW, STEPPED |
| Парткод: | RS5-9099-000CN |
| Деталь: | CONNECTOR, DRAWER |
| Парткод: | VS1-7257-012CN |
| Деталь: | Support, PCA |
| Парткод: | VT2-0001-008CN |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5694-000CN |
| Цена: | 320 ₽ |
| Деталь: | SCREW, TP, M3X6 |
| Парткод: | XA9-1469-000CN |
| Деталь: | CLAMP, CABLE |
| Парткод: | WT2-5738-000CN |
| Деталь: | Right-door assembly |
| Парткод: | RM1-3538-000CN |
| Деталь: | SCREW, RS, M4X8 |
| Парткод: | XA9-1448-000CN |
| Деталь: | Paper-feed PCA assembly |
| Парткод: | RM1-3569-000CN |
| Деталь: | Cable, pickup-option drawer |
| Парткод: | RM1-3571-000CN |
| Деталь: | Cable, pickup-option door switch |
| Парткод: | RM1-3572-000CN |
| Деталь: | Cable, option-sensor PCA connect |
| Парткод: | RM1-3574-000CN |
| Деталь: | Cable, paper-pickup option |
| Парткод: | RM1-3575-000CN |
| Деталь: | Stock-box assembly |
| Парткод: | RM1-3539-000CN |
| Деталь: | ROLLER, RAIL |
| Парткод: | RC1-9231-000CN |
| Деталь: | Caster, double-lock, front |
| Парткод: | RC1-9896-000CN |
| Деталь: | Support, lock-shaft |
| Парткод: | RC1-9900-000CN |
| Деталь: | Plate, switch-cover |
| Парткод: | RC1-9901-000CN |
| Деталь: | SHAFT, LOCK |
| Парткод: | RC1-9912-000CN |
| Деталь: | ARM, LOCK |
| Парткод: | RC1-9913-000CN |
| Деталь: | BUSHING |
| Парткод: | RC1-9915-000CN |
| Деталь: | Caster, rear |
| Парткод: | RC1-9917-000CN |
| Деталь: | RAIL, CASSETTE, RIGHT |
| Парткод: | RL1-1310-000CN |
| Деталь: | RAIL, CASSETTE, LEFT |
| Парткод: | RL1-1311-000CN |
| Деталь: | Switch, button |
| Парткод: | WC2-5512-000CN |
| Деталь: | Screw, with washer, M5x12 |
| Парткод: | XA9-0912-000CN |
| Деталь: | Door, stock |
| Парткод: | RC1-9921-000CN |
| Деталь: | Screw, with washer, M3x6 |
| Парткод: | XB2-8300-607CN |
| Деталь: | Screw, tapping, pan-head, M4x10 |
| Парткод: | XB4-7401-006CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Saddle paper-delivery assembly |
| Парткод: | RM1-4130-000CN |
| Деталь: | Multi-tray cable |
| Парткод: | RM1-3630-000CN |
| Деталь: | Multi-purpose-tray assembly |
| Парткод: | RM1-3341-000CN |
| Цена: | 2 300 ₽ |
| Деталь: | COVER, LEFT |
| Парткод: | RC1-9336-000CN |
| Цена: | 1 900 ₽ |
| Деталь: | COVER, FRONT, UPPER |
| Парткод: | RC1-9350-000CN |
| Деталь: | Cover, paper-delivery |
| Парткод: | RC1-9351-000CN |
| Деталь: | Duplexing-tray lower assembly |
| Парткод: | RC1-5949-000CN |
| Деталь: | Front internal small-cover assembly |
| Парткод: | RC1-5953-000CN |
| Деталь: | Right-lower cover assembly |
| Парткод: | RL1-1280-000CN |
| Цена: | 1 200 ₽ |
| Деталь: | Cover, rear-left |
| Парткод: | RC1-9344-000CN |
| Деталь: | Rear-right cover assembly |
| Парткод: | RM1-4415-000CN |
| Деталь: | Face-down end-tray assembly |
| Парткод: | RM1-3340-000CN |
| Деталь: | Fixing-fan cover assembly |
| Парткод: | RM1-5950-000CN |
| Деталь: | COVER, REAR |
| Парткод: | RL1-1210-000CN |
| Деталь: | Cover, face-down drive |
| Парткод: | RC1-9360-000CN |
| Деталь: | Switchback-cover assembly |
| Парткод: | RM1-4408-000CN |
| Деталь: | Filter unit, air |
| Парткод: | RC1-9313-000CN |
| Деталь: | Screw, tapping, truss-head, M4X10 |
| Парткод: | XB4-7401-005CN |
| Цена: | 140 ₽ |
| Деталь: | Duplexing-feed assembly |
| Парткод: | RM1-3665-000CN |
| Цена: | 18 100 ₽ |
| Деталь: | Upper-guide assembly |
| Парткод: | RM1-4395-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0137-000CN |
| Деталь: | Stack-tray assembly |
| Парткод: | RM1-4104-000CN |
| Деталь: | Approach-switch assembly |
| Парткод: | FM2-0710-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | FC5-4221-000CN |
| Деталь: | GEAR, 44T |
| Парткод: | FU5-0435-000CN |
| Деталь: | GEAR, 17T |
| Парткод: | FU5-0457-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | RU5-6035-000CN |
| Деталь: | Area-sensor PCA assembly |
| Парткод: | 4G1-1498-000CN |
| Деталь: | Tray-driver PCA assembly |
| Парткод: | FG3-2887-000CN |
| Деталь: | Paper-sensor assembly |
| Парткод: | FM2-0707-000CN |
| Деталь: | Area-sensor holder assembly |
| Парткод: | FM2-0709-000CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2300-142CN |
| Деталь: | Stack upper-tray assembly |
| Парткод: | RM1-4102-000CN |
| Деталь: | Stack sub-tray assembly |
| Парткод: | RM1-4115-000CN |
| Деталь: | Return-roller assembly |
| Парткод: | FM2-0725-090 |
| Деталь: | CABLE, SENSOR |
| Парткод: | 4G1-2285-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Booklet-output bin (saddle-tray assembly) |
| Парткод: | RM1-4113-000CN |
| Деталь: | Entire scanner without power supply, boards, and cable |
| Парткод: | Q3938-60132 |
| Деталь: | Cover pick roller |
| Парткод: | Q3938-67954 |
| Деталь: | Jam-cover assembly |
| Парткод: | Q3938-67970 |
| Деталь: | Damper, gear |
| Парткод: | RC1-8925-000CN |
| Деталь: | RAIL, FIXING, FRONT |
| Парткод: | RC1-8931-000CN |
| Деталь: | DUCT, AIR |
| Парткод: | RC1-8961-000CN |
| Деталь: | Duct, face-down joint |
| Парткод: | RC1-8964-000CN |
| Деталь: | Tag PCA-holder assembly |
| Парткод: | RM1-4402-000CN |
| Деталь: | DUCT, CARTRIDGE |
| Парткод: | RC1-9276-000CN |
| Деталь: | Holder, cartridge-fan |
| Парткод: | RC1-9277-000CN |
| Деталь: | Holder, fixing-fan |
| Парткод: | RC1-9278-000CN |
| Деталь: | Holder, scanner-fan |
| Парткод: | RC1-9279-000CN |
| Деталь: | Duct, scanner-fan |
| Парткод: | RC1-9309-000CN |
| Деталь: | DC MOTOR ASSEMBLY |
| Парткод: | RM1-4519-000CN |
| Цена: | 2 700 ₽ |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-1366-000CN |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-1370-000CN |
| Цена: | 1 400 ₽ |
| Деталь: | Gear, 83T/25T |
| Парткод: | RU5-0790-000CN |
| Деталь: | GEAR, 34T |
| Парткод: | RU5-0791-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0234-000CN |
| Деталь: | BEARING, BALL |
| Парткод: | XG9-0586-000CN |
| Деталь: | Plate, fixing-motor |
| Парткод: | RL1-1216-000CN |
| Деталь: | Fixing one-way gear assembly |
| Парткод: | RM1-3247-000CN |
| Деталь: | Main drive-unit kit |
| Парткод: | Q3931-67911 |
| Цена: | 23 000 ₽ |
| Деталь: | Toner-cartridge drive-assembly kit with service document |
| Парткод: | Q3931-67912 |
| Деталь: | Toner-cartridge drive-assembly kit with service document |
| Парткод: | Q3931-67913 |
| Деталь: | Fixing assembly kit, 110-127V, with air filter (air filter is Ref 14 in Printer external panels and covers) |
| Парткод: | Q3931-67914 |
| Деталь: | Fixing assembly kit, 220-240V, with air filter (air filter is Ref 14 in Printer external panels and covers) |
| Парткод: | Q3931-67915 |
| Деталь: | Drum-motor assembly |
| Парткод: | RM1-3286-000CN |
| Цена: | 3 000 ₽ |
| Деталь: | RAIL, FIXING, REAR |
| Парткод: | RC1-8939-000CN |
| Деталь: | Memory-tag PCA assembly |
| Парткод: | RM1-3585-000CN |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1495-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1504-000CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD9-0240-000CN |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5694-000CN |
| Цена: | 320 ₽ |
| Деталь: | Toner-motor cable |
| Парткод: | RM1-3383-000CN |
| Деталь: | Toner-motor cable |
| Парткод: | RM1-3385-000CN |
| Деталь: | FAN |
| Парткод: | RK2-1377-000CN |
| Деталь: | FAN |
| Парткод: | RK2-1382-000CN |
| Деталь: | FAN |
| Парткод: | RK2-1378-000CN |
| Цена: | 1 600 ₽ |
| Деталь: | SCREW, TP, M3X6 |
| Парткод: | XA9-1159-000CN |
| Деталь: | Connector, snap-tight |
| Парткод: | VS1-7177-003CN |
| Деталь: | Screw, with washer, M3x6 |
| Парткод: | XB2-8300-607CN |
| Деталь: | Screw, machined, truss-head, M3x4 |
| Парткод: | XB1-2300-407CN |
| Деталь: | Arm, adjustment, front |
| Парткод: | 4A3-1763-000CN |
| Деталь: | Arm, adjustment, rear |
| Парткод: | 4A3-1764-000CN |
| Деталь: | Plate, rotation |
| Парткод: | 4A3-1779-000CN |
| Деталь: | LEVER, STOPPER |
| Парткод: | 4A3-1782-000CN |
| Деталь: | Roller, folding |
| Парткод: | 4A3-1783-000CN |
| Деталь: | GEAR, 50T |
| Парткод: | 4S3-0171-000CN |
| Деталь: | BEARING, BALL, 6902ZZNR |
| Парткод: | 4S3-1050-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | 4S3-2116-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | 4S3-2117-000CN |
| Деталь: | Flag, roller |
| Парткод: | FB3-7925-030CN |
| Деталь: | Deflector |
| Парткод: | FB3-7928-020CN |
| Деталь: | Rack, rear |
| Парткод: | FB3-7934-000CN |
| Деталь: | Rack, front |
| Парткод: | FB3-7967-000CN |
| Деталь: | HOLDER, ROLLER, 2 |
| Парткод: | FB3-7973-000CN |
| Деталь: | FLAG, SENSOR |
| Парткод: | FB3-7979-000CN |
| Деталь: | SPRING, TORSION |
| Парткод: | FB3-7980-000CN |
| Деталь: | Deflector |
| Парткод: | FB5-2697-000CN |
| Деталь: | FLAG, SENSOR |
| Парткод: | FB5-5937-020CN |
| Деталь: | Claw, latch, right |
| Парткод: | FC5-5021-000CN |
| Деталь: | PULLEY, 30T |
| Парткод: | FS5-3576-000CN |
| Деталь: | Pulley, 39T |
| Парткод: | FS5-3577-000CN |
| Деталь: | Gear, 16T/33T |
| Парткод: | FS6-0822-000CN |
| Деталь: | GEAR, 16T |
| Парткод: | FS6-0823-000CN |
| Деталь: | Gear, 16T/56T |
| Парткод: | FS6-0829-000CN |
| Деталь: | GEAR, 16T |
| Парткод: | FS6-0830-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | FS6-2582-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-3837-340CN |
| Деталь: | Cable, saddle-unit |
| Парткод: | 4G1-2283-000CN |
| Деталь: | Guide-motor assembly |
| Парткод: | 4G3-0725-000CN |
| Деталь: | Plate, tension |
| Парткод: | FF5-5805-040 |
| Деталь: | Rear-end sensor assembly |
| Парткод: | FM2-0763-000CN |
| Деталь: | Delivery-switch mount assembly |
| Парткод: | FM2-1639-000CN |
| Деталь: | Upper delivery-guide assembly |
| Парткод: | RM1-4131-000CN |
| Деталь: | Saddle-controller PCA assembly |
| Парткод: | RM1-4140-000CN |
| Деталь: | Saddle paper-delivery assembly |
| Парткод: | RM1-4130-000CN |
| Деталь: | Motor-mount assembly |
| Парткод: | 4G3-0670-000CN |
| Деталь: | Saddle-guide assembly |
| Парткод: | FM2-0756-000CN |
| Деталь: | Inner side-plate assembly |
| Парткод: | 4G3-0671-000CN |
| Деталь: | Saddle-stapler assembly |
| Парткод: | RM1-4178-000CN |
| Деталь: | Ring, C, external |
| Парткод: | XD2-3100-152CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2300-202CN |
| Деталь: | Lower-guide assembly |
| Парткод: | RM1-3686-000CN |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | FAN |
| Парткод: | RK2-1378-000CN |
| Цена: | 1 600 ₽ |
| Деталь: | Duplexing-reverse assembly |
| Парткод: | RM1-3652-000CN |
| Деталь: | Paper-feeder motor assembly |
| Парткод: | RM1-4175-000CN |
| Деталь: | Guide, cable, C |
| Парткод: | RC1-9308-000CN |
| Деталь: | GUIDE, CABLE, D |
| Парткод: | RC1-9312-000CN |
| Деталь: | GUIDE, CABLE, E |
| Парткод: | RC1-9318-000CN |
| Деталь: | Panel cable |
| Парткод: | RM1-3389-000CN |
| Деталь: | Formatter-case assembly |
| Парткод: | RM1-3253-000CN |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1495-000CN |
| Деталь: | DC-controller PCA assembly |
| Парткод: | RM1-6642-000CN |
| Деталь: | DC-controller power cable |
| Парткод: | RM1-3610-000CN |
| Деталь: | Front cable |
| Парткод: | RM1-3617-000CN |
| Деталь: | Rear-lower cable |
| Парткод: | RM1-3618-000CN |
| Деталь: | Rear-upper cable |
| Парткод: | RM1-3619-000CN |
| Деталь: | Scanner-joint cable |
| Парткод: | RM1-3620-000CN |
| Деталь: | Panel-joint cable |
| Парткод: | RM1-3622-000CN |
| Цена: | 420 ₽ |
| Деталь: | Interface-joint cable |
| Парткод: | RM1-3623-000CN |
| Деталь: | Color-plane-registration (CPR)-joint cable |
| Парткод: | RM1-3624-000CN |
| Деталь: | Waste-toner-sensor cable |
| Парткод: | RM1-3640-000CN |
| Деталь: | Rear-cover-mount plate assembly |
| Парткод: | RM1-3354-000CN |
| Деталь: | Fixing-motor cable |
| Парткод: | RM1-3217-000CN |
| Деталь: | GUIDE, CABLE, B |
| Парткод: | RC1-9307-000CN |
| Деталь: | CABLE, FLEXIBLE FLAT |
| Парткод: | RK2-1356-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1449-000CN |
| Деталь: | Tray, screw |
| Парткод: | RC1-9256-000CN |
| Деталь: | FOOT, RUBBER |
| Парткод: | RC1-9208-000CN |
| Деталь: | Pressure-roller assembly |
| Парткод: | FM2-0730-000CN |
| Деталь: | Cable, operation-tray |
| Парткод: | FG3-2903-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Operation-tray assembly |
| Парткод: | RM1-4125-000CN |
| Деталь: | Arm, adjustment, front |
| Парткод: | 4A3-1763-000CN |
| Деталь: | Arm, adjustment, rear |
| Парткод: | 4A3-1764-000CN |
| Деталь: | Plate, rotation |
| Парткод: | 4A3-1779-000CN |
| Деталь: | LEVER, STOPPER |
| Парткод: | 4A3-1782-000CN |
| Деталь: | Roller, folding |
| Парткод: | 4A3-1783-000CN |
| Деталь: | GEAR, 50T |
| Парткод: | 4S3-0171-000CN |
| Деталь: | BEARING, BALL, 6902ZZNR |
| Парткод: | 4S3-1050-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | 4S3-2116-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | 4S3-2117-000CN |
| Деталь: | Flag, roller |
| Парткод: | FB3-7925-030CN |
| Деталь: | Deflector |
| Парткод: | FB3-7928-020CN |
| Деталь: | Rack, rear |
| Парткод: | FB3-7934-000CN |
| Деталь: | Rack, front |
| Парткод: | FB3-7967-000CN |
| Деталь: | HOLDER, ROLLER, 2 |
| Парткод: | FB3-7973-000CN |
| Деталь: | FLAG, SENSOR |
| Парткод: | FB3-7979-000CN |
| Деталь: | SPRING, TORSION |
| Парткод: | FB3-7980-000CN |
| Деталь: | Deflector |
| Парткод: | FB5-2697-000CN |
| Деталь: | FLAG, SENSOR |
| Парткод: | FB5-5937-020CN |
| Деталь: | Claw, latch, right |
| Парткод: | FC5-5021-000CN |
| Деталь: | PULLEY, 30T |
| Парткод: | FS5-3576-000CN |
| Деталь: | Pulley, 39T |
| Парткод: | FS5-3577-000CN |
| Деталь: | Gear, 16T/33T |
| Парткод: | FS6-0822-000CN |
| Деталь: | GEAR, 16T |
| Парткод: | FS6-0823-000CN |
| Деталь: | Gear, 16T/56T |
| Парткод: | FS6-0829-000CN |
| Деталь: | GEAR, 16T |
| Парткод: | FS6-0830-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | FS6-2582-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-3837-340CN |
| Деталь: | Cable, saddle-unit |
| Парткод: | 4G1-2283-000CN |
| Деталь: | Guide-motor assembly |
| Парткод: | 4G3-0725-000CN |
| Деталь: | Plate, tension |
| Парткод: | FF5-5805-040 |
| Деталь: | Rear-end sensor assembly |
| Парткод: | FM2-0763-000CN |
| Деталь: | Delivery-switch mount assembly |
| Парткод: | FM2-1639-000CN |
| Деталь: | Upper delivery-guide assembly |
| Парткод: | RM1-4131-000CN |
| Деталь: | Saddle-controller PCA assembly |
| Парткод: | RM1-4140-000CN |
| Деталь: | Saddle paper-delivery assembly |
| Парткод: | RM1-4130-000CN |
| Деталь: | Motor-mount assembly |
| Парткод: | 4G3-0670-000CN |
| Деталь: | Saddle-guide assembly |
| Парткод: | FM2-0756-000CN |
| Деталь: | Inner side-plate assembly |
| Парткод: | 4G3-0671-000CN |
| Деталь: | Saddle-stapler assembly |
| Парткод: | RM1-4178-000CN |
| Деталь: | Ring, C, external |
| Парткод: | XD2-3100-152CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2300-202CN |
| Деталь: | End cover (cap) back |
| Парткод: | Q3938-67945 |
| Деталь: | Cable, ADF to scanner |
| Парткод: | Q3938-67948 |
| Деталь: | PCA motor assembly |
| Парткод: | Q7829-67903 |
| Деталь: | Tray-input assembly |
| Парткод: | Q3938-67950 |
| Деталь: | Reflector foam (white backing) |
| Парткод: | Q7829-67909 |
| Деталь: | Automatic document feeder (ADF) whole unit |
| Парткод: | Q3938-67943 |
| Деталь: | Flag sensor LS |
| Парткод: | Q3938-67951 |
| Деталь: | Photo interrupter with connector |
| Парткод: | Q7829-67914 |
| Деталь: | Maintenance kit |
| Парткод: | Q3938-67944 |
| Деталь: | Lever, paper-sensing |
| Парткод: | RC1-8928-000CN |
| Деталь: | Intermediate transfer belt (ITB) duct assembly |
| Парткод: | RM1-4401-000CN |
| Деталь: | Cover, cassette back-end |
| Парткод: | RC1-9201-000CN |
| Деталь: | Rail, left, top |
| Парткод: | RL1-1213-000CN |
| Деталь: | RAIL, CASSETTE, RIGHT |
| Парткод: | RL1-1215-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | RU5-2796-000CN |
| Деталь: | Low-voltage power-supply assembly |
| Парткод: | RM1-3594-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0234-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1504-000CN |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1495-000CN |
| Деталь: | Plate, fan-fixing, front |
| Парткод: | RC1-9190-000CN |
| Деталь: | Lever, door-interlock shutter |
| Парткод: | RC1-9220-000CN |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | CONNECTOR, DRAWER |
| Парткод: | VS1-7258-000CN |
| Деталь: | Plate, drawer-guard |
| Парткод: | RC1-9235-000CN |
| Деталь: | PLATE, SENSOR, FRONT |
| Парткод: | RC1-9246-000CN |
| Деталь: | Guide-sensor assembly |
| Парткод: | RM1-4400-000CN |
| Деталь: | SPRING, TORSION |
| Парткод: | RC1-9244-000CN |
| Деталь: | FAN |
| Парткод: | RK2-1378-000CN |
| Цена: | 1 600 ₽ |
| Деталь: | Cable, fixing open-sensor |
| Парткод: | RM1-5029-000CN |
| Деталь: | Screw, tapping, truss-head, M4X10 |
| Парткод: | XB4-7401-005CN |
| Цена: | 140 ₽ |
| Деталь: | Screw, TP, M3x30 |
| Парткод: | XB6-7303-005CN |
| Деталь: | Copy processor board (CPB) |
| Парткод: | Q3938-67940 |
| Деталь: | SCUID board |
| Парткод: | Q3938-67941 |
| Деталь: | PCIe cable |
| Парткод: | Q3938-67942 |
| Деталь: | 512 MB image scanner memory DIMM |
| Парткод: | Q7559A |
| Деталь: | Cassette (1x500-sheet) |
| Парткод: | RM1-3529-000CN |
| Деталь: | Cassette (3x500-sheet) |
| Парткод: | RM1-3529-000CN |
| Деталь: | Lifter-drive-assembly kit |
| Парткод: | RM1-3222-000CN |
| Деталь: | GUIDE, CABLE, A |
| Парткод: | RC1-9306-000CN |
| Деталь: | Cover, main-switch |
| Парткод: | RC1-9211-000CN |
| Деталь: | GUIDE, CABLE, F |
| Парткод: | RC1-9323-000CN |
| Деталь: | Plate, high-voltage transmission (HVT-A) guard |
| Парткод: | RC1-9326-000CN |
| Деталь: | Fixing power-supply assembly |
| Парткод: | RM1-3218-000CN |
| Деталь: | Cartridge contact-holder assembly |
| Парткод: | RM1-3254-000CN |
| Деталь: | Cartridge-interface assembly kit with service document |
| Парткод: | Q3931-67917 |
| Деталь: | Holder, high-voltage-connector |
| Парткод: | RC1-9328-000CN |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | Face-down unit-1 cable |
| Парткод: | RM1-3390-000CN |
| Деталь: | Face-down unit-2 cable |
| Парткод: | RM1-3391-000CN |
| Деталь: | High-voltage-transfer A PCA assembly |
| Парткод: | RM1-3582-000CN |
| Деталь: | Button, main-switch |
| Парткод: | RC1-9300-000CN |
| Деталь: | Fixing-joint cable |
| Парткод: | RM1-3612-000CN |
| Деталь: | T2 guide-arm assembly |
| Парткод: | RM1-4411-000CN |
| Деталь: | Fixing-bias cable assembly |
| Парткод: | RM1-4409-000CN |
| Деталь: | Guide, fixing-cable |
| Парткод: | RC1-9332-000CN |
| Деталь: | Main switch-holder assembly |
| Парткод: | RM1-3252-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1504-000CN |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1495-000CN |
| Деталь: | Cable TP/T2 open-sensor |
| Парткод: | RM1-5030-000CN |
| Деталь: | Cable, MFP AC |
| Парткод: | RM1-3599-000CN |
| Деталь: | Screw, RS, M13x12 |
| Парткод: | XA9-1801-000CN |
| Деталь: | Screw, machined, truss-head, M4x8 |
| Парткод: | XB1-2400-805CN |
| Деталь: | Scanner controller board (SCB) fan |
| Парткод: | Q3938-67937 |
| Деталь: | Scanner fan |
| Парткод: | Q3938-67938 |
| Деталь: | Control-panel fan |
| Парткод: | Q3938-67939 |
| Деталь: | Flag, paper-sensing sensor |
| Парткод: | FC5-5004-000CN |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-5005-000CN |
| Деталь: | COVER, REAR |
| Парткод: | RC2-1278-000CN |
| Деталь: | Cover, tray-connector |
| Парткод: | RC2-1279-000CN |
| Деталь: | Paper-face sensor assembly |
| Парткод: | 4G3-0934-000CN |
| Деталь: | Paper-face sensing assembly |
| Парткод: | 4G3-1624-000CN |
| Деталь: | Top-door (upper-cover) assembly |
| Парткод: | RM1-4121-000CN |
| Деталь: | Front-door assembly |
| Парткод: | RM1-4134-000CN |
| Деталь: | Lower height-guide assembly |
| Парткод: | RM1-4135-000CN |
| Деталь: | Left upper-cover assembly |
| Парткод: | RM1-4179-000CN |
| Деталь: | Panel, height, upper |
| Парткод: | RC2-1283-000CN |
| Деталь: | Cover, option-slide |
| Парткод: | RC2-1347-000CN |
| Деталь: | Flag, paper-face sensing, upper |
| Парткод: | FC5-4162-000CN |
| Деталь: | Cover, front-lower |
| Парткод: | RL1-1717-000CN |
| Деталь: | Cover, rear-lower |
| Парткод: | RL1-1718-000CN |
| Деталь: | LED-PCA assembly |
| Парткод: | RM1-4141-000CN |
| Деталь: | Link-slide assembly |
| Парткод: | 4G3-0271-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Mount, LED-PCA |
| Парткод: | RC2-1735-000CN |
| Деталь: | TIMING BELT |
| Парткод: | Q3938-67935 |
| Деталь: | Stack-tray assembly |
| Парткод: | RM1-4104-000CN |
| Деталь: | Area-sensor holder assembly |
| Парткод: | FM2-0709-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | FC5-4221-000CN |
| Деталь: | Paper-sensor assembly |
| Парткод: | FM2-0707-000CN |
| Деталь: | GEAR, 44T |
| Парткод: | FU5-0435-000CN |
| Деталь: | GEAR, 17T |
| Парткод: | FU5-0457-000CN |
| Деталь: | BUSHING |
| Парткод: | FU5-1169-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | RU5-6035-000CN |
| Деталь: | Area-sensor PCA assembly |
| Парткод: | 4G1-1498-000CN |
| Деталь: | Tray-driver PCA assembly |
| Парткод: | FG3-2887-000CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2300-142CN |
| Деталь: | Stack lower-tray assembly |
| Парткод: | RM1-4105-000CN |
| Деталь: | SPRING, LEAF |
| Парткод: | RC1-9233-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1504-000CN |
| Деталь: | Top-cover assembly |
| Парткод: | RL1-1284-000CN |
| Деталь: | High-voltage transfer B PCA assembly |
| Парткод: | RM1-5475-000CN |
| Деталь: | Right-side wall assembly |
| Парткод: | RM1-3239-000CN |
| Деталь: | Transfer contact-holder assembly |
| Парткод: | RM1-3230-000CN |
| Деталь: | Partition-plate assembly, cyan |
| Парткод: | RM1-3238-000CN |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1495-000CN |
| Деталь: | Left-side wall assembly |
| Парткод: | RM1-3233-000CN |
| Деталь: | Partition-plate assembly, yellow |
| Парткод: | RM1-3235-000CN |
| Деталь: | Partition-plate assembly, magenta |
| Парткод: | RM1-3237-000CN |
| Деталь: | Scanner controller-board (SCB) |
| Парткод: | Q3938-67902 |
| Деталь: | Option-sensor assembly |
| Парткод: | FM2-1708-000CN |
| Деталь: | Plate, option-tray, front |
| Парткод: | FC5-6978-000CN |
| Деталь: | GEAR, 44T |
| Парткод: | FU5-0435-000CN |
| Деталь: | Cover, option-tray, front |
| Парткод: | RL1-2210-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | RU5-6035-000CN |
| Деталь: | Area-sensor PCA assembly |
| Парткод: | 4G1-1498-000CN |
| Деталь: | Paper-sensor assembly |
| Парткод: | FM2-0707-000CN |
| Деталь: | Area-sensor holder assembly |
| Парткод: | FM2-0709-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Stack upper-tray assembly |
| Парткод: | RM1-4101-000CN |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FC5-3657-000CN |
| Деталь: | Hinge, front-door, 1 |
| Парткод: | FC5-4991-030CN |
| Деталь: | Hinge, front-door, 2 |
| Парткод: | FC5-4992-030CN |
| Деталь: | Rack, rail |
| Парткод: | FC5-5436-000CN |
| Деталь: | GEAR, 30T |
| Парткод: | FU5-0428-000CN |
| Деталь: | GEAR, 40T |
| Парткод: | FU5-0454-000CN |
| Деталь: | GEAR, 29T |
| Парткод: | FU5-2399-000CN |
| Деталь: | PULLEY, 20T |
| Парткод: | FU5-3086-000CN |
| Деталь: | Screw, RS stepped, M3 |
| Парткод: | FU9-9059-000CN |
| Деталь: | Cover, internal, lower (stapler/stacker only) |
| Парткод: | RC2-1351-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1386-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF2-1607-860CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-840CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF9-0748-000CN |
| Деталь: | Upper-cover lock assembly |
| Парткод: | 4G3-0210-000CN |
| Деталь: | Screw, RS, M4x8 (booklet-maker only) |
| Парткод: | XA9-0732-000CN |
| Деталь: | Stack-ejection motor assembly |
| Парткод: | 4G3-0769-000CN |
| Деталь: | CABLE, SOLENOID |
| Парткод: | FG3-2892-000CN |
| Деталь: | Shutter H.P. sensor assembly |
| Парткод: | FM2-1401-000CN |
| Деталь: | Upper-crossmember assembly |
| Парткод: | RM1-4180-000CN |
| Деталь: | Press-motor assembly |
| Парткод: | FM2-1409-000CN |
| Деталь: | Sensor/switch assembly |
| Парткод: | FM2-1417-000CN |
| Деталь: | Swing-press shaft assembly |
| Парткод: | FM2-1423-000CN |
| Деталь: | Area-sensor flag assembly |
| Парткод: | RM1-4107-000CN |
| Деталь: | Caster, universal |
| Парткод: | RC2-1315-000CN |
| Деталь: | Screw, with washer, M5x12 |
| Парткод: | XA9-0912-000CN |
| Деталь: | Inner-cover assembly |
| Парткод: | RM1-4123-000CN |
| Деталь: | Cable-mount lattice assembly |
| Парткод: | RM1-4128-000CN |
| Деталь: | Sheet, entrance-guide |
| Парткод: | FC5-5542-000CN |
| Деталь: | SOLENOID |
| Парткод: | FL2-0821-000CN |
| Деталь: | PIN |
| Парткод: | XD3-2200-102CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-142CN |
| Деталь: | Entrance-sensor flag assembly |
| Парткод: | FM2-0718-000CN |
| Деталь: | Plate, hinge-stop (booklet-maker only) |
| Парткод: | 4A3-4715-000CN |
| Деталь: | Knob (booklet-maker only) |
| Парткод: | FB3-7881-000CN |
| Деталь: | Cover, internal, lower (booklet-maker only) |
| Парткод: | RL1-1477-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | 4A3-1955-000CN |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | 4H3-0370-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | RC2-1356-000CN |
| Деталь: | Flexible-cable mount assembly |
| Парткод: | FM2-0720-000CN |
| Деталь: | Screw, TP, M3x6 (booklet-maker only) |
| Парткод: | XB6-7300-607CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Roller, paper-pickup |
| Парткод: | RL1-1289-000CN |
| Цена: | 470 ₽ |
| Деталь: | Paper feed-roller assembly |
| Парткод: | RM1-0037-020CN |
| Цена: | 70 ₽ |
| Деталь: | Option paper-sensor PCA assembly |
| Парткод: | RM1-3570-000CN |
| Деталь: | Upper-left cover |
| Парткод: | Q3938-67920 |
| Деталь: | Lower-left cover |
| Парткод: | Q3938-67921 |
| Деталь: | Upper-right cover |
| Парткод: | Q3938-67922 |
| Деталь: | Lower-right cover |
| Парткод: | Q3938-67923 |
| Деталь: | TOP COVER |
| Парткод: | Q3938-67924 |
| Деталь: | REAR COVER |
| Парткод: | Q3938-67925 |
| Деталь: | FRONT COVER |
| Парткод: | Q3938-67926 |
| Деталь: | Screw covers |
| Парткод: | Q3938-67927 |
| Деталь: | Booklet-maker (multi-function finisher) whole unit |
| Парткод: | CC516A |
| Деталь: | Large-pin assembly |
| Парткод: | Q3938-67903 |
| Деталь: | Small-pin assembly |
| Парткод: | Q3938-67904 |
| Деталь: | Face-down full-flag assembly |
| Парткод: | RM1-4391-000CN |
| Деталь: | Paper-delivery-guide assembly |
| Парткод: | RM1-4407-000CN |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | Face-down paper-delivery assembly |
| Парткод: | RM1-3293-000CN |
| Деталь: | Entrance upper-guide assembly |
| Парткод: | RM1-4172-000CN |
| Деталь: | Upper-left cover |
| Парткод: | Q3938-67920 |
| Деталь: | Lower-left cover |
| Парткод: | Q3938-67921 |
| Деталь: | Upper-right cover |
| Парткод: | Q3938-67922 |
| Деталь: | Lower-right cover |
| Парткод: | Q3938-67923 |
| Деталь: | TOP COVER |
| Парткод: | Q3938-67924 |
| Деталь: | REAR COVER |
| Парткод: | Q3938-67925 |
| Деталь: | FRONT COVER |
| Парткод: | Q3938-67926 |
| Деталь: | Screw covers |
| Парткод: | Q3938-67927 |
| Деталь: | Glass assembly |
| Парткод: | Q3938-67906 |
| Деталь: | Cable, operation-tray |
| Парткод: | FG3-2903-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Operation-tray assembly |
| Парткод: | RM1-4125-000CN |
| Деталь: | Pulley assembly |
| Парткод: | Q3938-67909 |
| Деталь: | Inverter assembly |
| Парткод: | Q3938-67905 |
| Деталь: | Cover, multi-purpose blanking |
| Парткод: | RC1-8527-000CN |
| Деталь: | Right-door sub-assembly |
| Парткод: | RM1-3333-000CN |
| Деталь: | COVER, MOTOR |
| Парткод: | RC1-9511-000CN |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1495-000CN |
| Деталь: | Screw, with washer, M4X12 |
| Парткод: | XA9-1422-000CN |
| Деталь: | Guide, duplexing-feed, upper |
| Парткод: | RL1-1335-000CN |
| Деталь: | Screw, tapping, truss-head, M4X10 |
| Парткод: | XB4-7401-005CN |
| Цена: | 140 ₽ |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | Power-supply harness |
| Парткод: | Q3938-67928 |
| Деталь: | Power-supply assembly |
| Парткод: | Q3938-67910 |
| Деталь: | Cable, pickup-option lifter unit |
| Парткод: | RM1-3576-000CN |
| Деталь: | Auto-close assembly, 1x500-sheet |
| Парткод: | RM1-3531-040CN |
| Деталь: | Auto-close assembly, 3x500-sheet |
| Парткод: | RM1-3531-040CN |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FC5-3657-000CN |
| Деталь: | Hinge, front-door, 1 |
| Парткод: | FC5-4991-030CN |
| Деталь: | Hinge, front-door, 2 |
| Парткод: | FC5-4992-030CN |
| Деталь: | Rack, rail |
| Парткод: | FC5-5436-000CN |
| Деталь: | GEAR, 30T |
| Парткод: | FU5-0428-000CN |
| Деталь: | GEAR, 40T |
| Парткод: | FU5-0454-000CN |
| Деталь: | GEAR, 29T |
| Парткод: | FU5-2399-000CN |
| Деталь: | PULLEY, 20T |
| Парткод: | FU5-3086-000CN |
| Деталь: | Screw, RS stepped, M3 |
| Парткод: | FU9-9059-000CN |
| Деталь: | Cover, internal, lower (stapler/stacker only) |
| Парткод: | RC2-1351-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1386-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF2-1607-860CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-840CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF9-0748-000CN |
| Деталь: | Upper-cover lock assembly |
| Парткод: | 4G3-0210-000CN |
| Деталь: | Screw, RS, M4x8 (booklet-maker only) |
| Парткод: | XA9-0732-000CN |
| Деталь: | Stack-ejection motor assembly |
| Парткод: | 4G3-0769-000CN |
| Деталь: | CABLE, SOLENOID |
| Парткод: | FG3-2892-000CN |
| Деталь: | Shutter H.P. sensor assembly |
| Парткод: | FM2-1401-000CN |
| Деталь: | Upper-crossmember assembly |
| Парткод: | RM1-4180-000CN |
| Деталь: | Press-motor assembly |
| Парткод: | FM2-1409-000CN |
| Деталь: | Sensor/switch assembly |
| Парткод: | FM2-1417-000CN |
| Деталь: | Swing-press shaft assembly |
| Парткод: | FM2-1423-000CN |
| Деталь: | Area-sensor flag assembly |
| Парткод: | RM1-4107-000CN |
| Деталь: | Caster, universal |
| Парткод: | RC2-1315-000CN |
| Деталь: | Screw, with washer, M5x12 |
| Парткод: | XA9-0912-000CN |
| Деталь: | Inner-cover assembly |
| Парткод: | RM1-4123-000CN |
| Деталь: | Cable-mount lattice assembly |
| Парткод: | RM1-4128-000CN |
| Деталь: | Sheet, entrance-guide |
| Парткод: | FC5-5542-000CN |
| Деталь: | SOLENOID |
| Парткод: | FL2-0821-000CN |
| Деталь: | PIN |
| Парткод: | XD3-2200-102CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-142CN |
| Деталь: | Entrance-sensor flag assembly |
| Парткод: | FM2-0718-000CN |
| Деталь: | Plate, hinge-stop (booklet-maker only) |
| Парткод: | 4A3-4715-000CN |
| Деталь: | Knob (booklet-maker only) |
| Парткод: | FB3-7881-000CN |
| Деталь: | Cover, internal, lower (booklet-maker only) |
| Парткод: | RL1-1477-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | 4A3-1955-000CN |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | 4H3-0370-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | RC2-1356-000CN |
| Деталь: | Flexible-cable mount assembly |
| Парткод: | FM2-0720-000CN |
| Деталь: | Screw, TP, M3x6 (booklet-maker only) |
| Парткод: | XB6-7300-607CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | 5000-staple replacement cartridge |
| Парткод: | C8091-67901 |
| Деталь: | 2000-staple cartridge (for booklet making) |
| Парткод: | CC383-67901 |
| Деталь: | Stapler unit |
| Парткод: | FL2-0846-000CN |
| Деталь: | Saddle-stapler assembly |
| Парткод: | RM1-4178-000CN |
| Деталь: | Diverter |
| Парткод: | Q3938-67953 |
| Деталь: | Photo interrupter with connector |
| Парткод: | Q7829-67914 |
| Деталь: | Float assembly |
| Парткод: | Q7829-67917 |
| Цена: | 1 500 ₽ |
| Деталь: | Knob, latch |
| Парткод: | FC5-5024-000CN |
| Деталь: | Saddle-guide assembly |
| Парткод: | FM2-5024-000CN |
| Деталь: | Fixing power-supply assembly |
| Парткод: | RM1-3218-000CN |
| Деталь: | DC controller PCA assembly |
| Парткод: | RM1-6642-000CN |
| Деталь: | High-voltage-transfer A PCA assembly |
| Парткод: | RM1-3582-000CN |
| Деталь: | High-voltage-transfer B PCA assembly |
| Парткод: | RM1-5475-000CN |
| Деталь: | Memory-tag PCA assembly |
| Парткод: | RM1-3585-000CN |
| Деталь: | Low-voltage power-supply assembly |
| Парткод: | RM1-3594-000CN |
| Деталь: | Lid-sensor assembly |
| Парткод: | Q3938-67907 |
| Деталь: | Upper-left cover |
| Парткод: | Q3938-67920 |
| Деталь: | Lower-left cover |
| Парткод: | Q3938-67921 |
| Деталь: | Upper-right cover |
| Парткод: | Q3938-67922 |
| Деталь: | Lower-right cover |
| Парткод: | Q3938-67923 |
| Деталь: | TOP COVER |
| Парткод: | Q3938-67924 |
| Деталь: | REAR COVER |
| Парткод: | Q3938-67925 |
| Деталь: | FRONT COVER |
| Парткод: | Q3938-67926 |
| Деталь: | Screw covers |
| Парткод: | Q3938-67927 |
| Деталь: | Option-sensor assembly |
| Парткод: | FM2-1708-000CN |
| Деталь: | Plate, option-tray, front |
| Парткод: | FC5-6978-000CN |
| Деталь: | GEAR, 44T |
| Парткод: | FU5-0435-000CN |
| Деталь: | Cover, option-tray, front |
| Парткод: | RL1-2210-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | RU5-6035-000CN |
| Деталь: | Area-sensor PCA assembly |
| Парткод: | 4G1-1498-000CN |
| Деталь: | Paper-sensor assembly |
| Парткод: | FM2-0707-000CN |
| Деталь: | Area-sensor holder assembly |
| Парткод: | FM2-0709-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Stack upper-tray assembly |
| Парткод: | RM1-4101-000CN |
| Деталь: | Stack-tray assembly |
| Парткод: | RM1-4104-000CN |
| Деталь: | Area-sensor holder assembly |
| Парткод: | FM2-0709-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | FC5-4221-000CN |
| Деталь: | Paper-sensor assembly |
| Парткод: | FM2-0707-000CN |
| Деталь: | GEAR, 44T |
| Парткод: | FU5-0435-000CN |
| Деталь: | GEAR, 17T |
| Парткод: | FU5-0457-000CN |
| Деталь: | BUSHING |
| Парткод: | FU5-1169-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | RU5-6035-000CN |
| Деталь: | Area-sensor PCA assembly |
| Парткод: | 4G1-1498-000CN |
| Деталь: | Tray-driver PCA assembly |
| Парткод: | FG3-2887-000CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2300-142CN |
| Деталь: | Stack lower-tray assembly |
| Парткод: | RM1-4105-000CN |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | Cassette paper-pickup assembly |
| Парткод: | RM1-3206-000CN |
| Цена: | 10 600 ₽ |
| Деталь: | Tray 2 pickup, feed-roller kit |
| Парткод: | Q3931-67919 |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FC5-3657-000CN |
| Деталь: | Hinge, front-door, 1 |
| Парткод: | FC5-4991-030CN |
| Деталь: | Hinge, front-door, 2 |
| Парткод: | FC5-4992-030CN |
| Деталь: | Rack, rail |
| Парткод: | FC5-5436-000CN |
| Деталь: | GEAR, 30T |
| Парткод: | FU5-0428-000CN |
| Деталь: | GEAR, 40T |
| Парткод: | FU5-0454-000CN |
| Деталь: | GEAR, 29T |
| Парткод: | FU5-2399-000CN |
| Деталь: | PULLEY, 20T |
| Парткод: | FU5-3086-000CN |
| Деталь: | Screw, RS stepped, M3 |
| Парткод: | FU9-9059-000CN |
| Деталь: | Cover, internal, lower (stapler/stacker only) |
| Парткод: | RC2-1351-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1386-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF2-1607-860CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-840CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF9-0748-000CN |
| Деталь: | Upper-cover lock assembly |
| Парткод: | 4G3-0210-000CN |
| Деталь: | Screw, RS, M4x8 (booklet-maker only) |
| Парткод: | XA9-0732-000CN |
| Деталь: | Stack-ejection motor assembly |
| Парткод: | 4G3-0769-000CN |
| Деталь: | CABLE, SOLENOID |
| Парткод: | FG3-2892-000CN |
| Деталь: | Shutter H.P. sensor assembly |
| Парткод: | FM2-1401-000CN |
| Деталь: | Upper-crossmember assembly |
| Парткод: | RM1-4180-000CN |
| Деталь: | Press-motor assembly |
| Парткод: | FM2-1409-000CN |
| Деталь: | Sensor/switch assembly |
| Парткод: | FM2-1417-000CN |
| Деталь: | Swing-press shaft assembly |
| Парткод: | FM2-1423-000CN |
| Деталь: | Area-sensor flag assembly |
| Парткод: | RM1-4107-000CN |
| Деталь: | Caster, universal |
| Парткод: | RC2-1315-000CN |
| Деталь: | Screw, with washer, M5x12 |
| Парткод: | XA9-0912-000CN |
| Деталь: | Inner-cover assembly |
| Парткод: | RM1-4123-000CN |
| Деталь: | Cable-mount lattice assembly |
| Парткод: | RM1-4128-000CN |
| Деталь: | Sheet, entrance-guide |
| Парткод: | FC5-5542-000CN |
| Деталь: | SOLENOID |
| Парткод: | FL2-0821-000CN |
| Деталь: | PIN |
| Парткод: | XD3-2200-102CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-142CN |
| Деталь: | Entrance-sensor flag assembly |
| Парткод: | FM2-0718-000CN |
| Деталь: | Plate, hinge-stop (booklet-maker only) |
| Парткод: | 4A3-4715-000CN |
| Деталь: | Knob (booklet-maker only) |
| Парткод: | FB3-7881-000CN |
| Деталь: | Cover, internal, lower (booklet-maker only) |
| Парткод: | RL1-1477-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | 4A3-1955-000CN |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | 4H3-0370-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | RC2-1356-000CN |
| Деталь: | Flexible-cable mount assembly |
| Парткод: | FM2-0720-000CN |
| Деталь: | Screw, TP, M3x6 (booklet-maker only) |
| Парткод: | XB6-7300-607CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Arm, adjustment, front |
| Парткод: | 4A3-1763-000CN |
| Деталь: | Arm, adjustment, rear |
| Парткод: | 4A3-1764-000CN |
| Деталь: | Plate, rotation |
| Парткод: | 4A3-1779-000CN |
| Деталь: | LEVER, STOPPER |
| Парткод: | 4A3-1782-000CN |
| Деталь: | Roller, folding |
| Парткод: | 4A3-1783-000CN |
| Деталь: | GEAR, 50T |
| Парткод: | 4S3-0171-000CN |
| Деталь: | BEARING, BALL, 6902ZZNR |
| Парткод: | 4S3-1050-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | 4S3-2116-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | 4S3-2117-000CN |
| Деталь: | Flag, roller |
| Парткод: | FB3-7925-030CN |
| Деталь: | Deflector |
| Парткод: | FB3-7928-020CN |
| Деталь: | Rack, rear |
| Парткод: | FB3-7934-000CN |
| Деталь: | Rack, front |
| Парткод: | FB3-7967-000CN |
| Деталь: | HOLDER, ROLLER, 2 |
| Парткод: | FB3-7973-000CN |
| Деталь: | FLAG, SENSOR |
| Парткод: | FB3-7979-000CN |
| Деталь: | SPRING, TORSION |
| Парткод: | FB3-7980-000CN |
| Деталь: | Deflector |
| Парткод: | FB5-2697-000CN |
| Деталь: | FLAG, SENSOR |
| Парткод: | FB5-5937-020CN |
| Деталь: | Claw, latch, right |
| Парткод: | FC5-5021-000CN |
| Деталь: | PULLEY, 30T |
| Парткод: | FS5-3576-000CN |
| Деталь: | Pulley, 39T |
| Парткод: | FS5-3577-000CN |
| Деталь: | Gear, 16T/33T |
| Парткод: | FS6-0822-000CN |
| Деталь: | GEAR, 16T |
| Парткод: | FS6-0823-000CN |
| Деталь: | Gear, 16T/56T |
| Парткод: | FS6-0829-000CN |
| Деталь: | GEAR, 16T |
| Парткод: | FS6-0830-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | FS6-2582-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-3837-340CN |
| Деталь: | Cable, saddle-unit |
| Парткод: | 4G1-2283-000CN |
| Деталь: | Guide-motor assembly |
| Парткод: | 4G3-0725-000CN |
| Деталь: | Plate, tension |
| Парткод: | FF5-5805-040 |
| Деталь: | Rear-end sensor assembly |
| Парткод: | FM2-0763-000CN |
| Деталь: | Delivery-switch mount assembly |
| Парткод: | FM2-1639-000CN |
| Деталь: | Upper delivery-guide assembly |
| Парткод: | RM1-4131-000CN |
| Деталь: | Saddle-controller PCA assembly |
| Парткод: | RM1-4140-000CN |
| Деталь: | Saddle paper-delivery assembly |
| Парткод: | RM1-4130-000CN |
| Деталь: | Motor-mount assembly |
| Парткод: | 4G3-0670-000CN |
| Деталь: | Saddle-guide assembly |
| Парткод: | FM2-0756-000CN |
| Деталь: | Inner side-plate assembly |
| Парткод: | 4G3-0671-000CN |
| Деталь: | Saddle-stapler assembly |
| Парткод: | RM1-4178-000CN |
| Деталь: | Ring, C, external |
| Парткод: | XD2-3100-152CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2300-202CN |
| Деталь: | CARRIAGE ASSEMBLY |
| Парткод: | Q3938-67901 |
| Деталь: | Multi-purpose-drive assembly |
| Парткод: | RM1-3366-000CN |
| Деталь: | 5000-staple replacement cartridge |
| Парткод: | C8091-67901 |
| Деталь: | 2000-staple cartridge (for booklet making) |
| Парткод: | CC383-67901 |
| Деталь: | Stapler sub-assembly |
| Парткод: | FM2-0722-000CN |
| Деталь: | Cable, staple-connecting assembly |
| Парткод: | 4G3-1777-000CN |
| Деталь: | STAPLE ASSEMBLY |
| Парткод: | FM2-0721-000CN |
| Деталь: | TIMING BELT |
| Парткод: | Q3938-67935 |
| Деталь: | Left-assist assembly |
| Парткод: | RM1-4396-000CN |
| Деталь: | Stapler/stacker whole unit |
| Парткод: | CC517A |
| Деталь: | Saddle-motor assembly |
| Парткод: | FM2-0737-000CN |
| Деталь: | Entrance lower-guide assembly |
| Парткод: | RM1-4110-000CN |
| Деталь: | Saddle paper-feeder assembly |
| Парткод: | RM1-4136-000CN |
| Деталь: | MOTOR, STEPPING |
| Парткод: | 4K1-1103-000CN |
| Деталь: | Pulley, 32T/gear, 16T |
| Парткод: | FS6-0814-000CN |
| Деталь: | Pulley, 16T/gear, 32T |
| Парткод: | FS6-0815-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Retainer |
| Парткод: | RC1-8511-000CN |
| Деталь: | BUSHING |
| Парткод: | RC1-8734-000CN |
| Деталь: | Guide, intermediate transfer belt (ITB)-entrance, rear |
| Парткод: | RC1-9186-000CN |
| Деталь: | Guide, intermediate transfer belt (ITB)-entrance, front |
| Парткод: | RC1-9185-000CN |
| Деталь: | Arm, 1st-estrangement |
| Парткод: | RC1-9189-000CN |
| Деталь: | COVER, INTERNAL, RIGHT |
| Парткод: | RC1-9348-000CN |
| Деталь: | Intermediate transfer belt (ITB) lock-support rear assembly |
| Парткод: | RM1-3215-000CN |
| Деталь: | Intermediate transfer belt (ITB) lock-support front assembly |
| Парткод: | RM1-3228-000CN |
| Деталь: | Intermediate transfer belt (ITB)-drawer assembly |
| Парткод: | RM1-3240-000CN |
| Деталь: | Intermediate transfer belt (ITB) estrangement-drive assembly |
| Парткод: | RM1-3280-000CN |
| Деталь: | Registration 2nd-transfer assembly kit with service document |
| Парткод: | Q3931-67909 |
| Деталь: | 2nd-transfer-roller assembly kit |
| Парткод: | Q3931-67910 |
| Деталь: | Intermediate transfer belt (ITB) assembly kit |
| Парткод: | Q3931-67908 |
| Деталь: | Color-plane-registration (CPR) sensor assembly |
| Парткод: | RM1-3258-000CN |
| Цена: | 4 400 ₽ |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1495-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1504-000CN |
| Деталь: | COVER, REAR |
| Парткод: | RC1-9871-000CN |
| Деталь: | COVER, LEFT |
| Парткод: | RC1-9872-000CN |
| Деталь: | Cover, front-upper |
| Парткод: | RC1-9873-000CN |
| Деталь: | Cover, right-lower |
| Парткод: | RC1-9874-000CN |
| Деталь: | Guide, paper-feed roller |
| Парткод: | RC1-9881-000CN |
| Деталь: | Stopper, right-door |
| Парткод: | RC1-9882-000CN |
| Деталь: | LEVER, LOCK |
| Парткод: | RC1-9883-000CN |
| Деталь: | Tape, door |
| Парткод: | RC1-9884-000CN |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-1331-000CN |
| Цена: | 2 500 ₽ |
| Деталь: | Cover, right-front |
| Парткод: | RL1-1321-000CN |
| Деталь: | SCREW, STEPPED |
| Парткод: | RS5-9099-000CN |
| Деталь: | CONNECTOR, DRAWER |
| Парткод: | VS1-7257-012CN |
| Деталь: | Support, PCA |
| Парткод: | VT2-001-008CN |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5694-000CN |
| Цена: | 320 ₽ |
| Деталь: | CLAMP, CABLE |
| Парткод: | WT2-5738-000CN |
| Деталь: | SCREW, RS, M4X8 |
| Парткод: | XA9-1448-000CN |
| Деталь: | SCREW, TP, M3X6 |
| Парткод: | XA9-1469-000CN |
| Деталь: | Right-door assembly |
| Парткод: | RM1-3537-000CN |
| Деталь: | Paper-feed PCA assembly |
| Парткод: | RM1-3569-000CN |
| Деталь: | Cable, paper-pickup-option drawer |
| Парткод: | RM1-3571-000CN |
| Деталь: | Cable, pickup-option door switch |
| Парткод: | RM1-3572-000CN |
| Деталь: | Cable, option-sensor PCA connect |
| Парткод: | RM1-3574-000CN |
| Деталь: | Cable, paper-pickup option |
| Парткод: | RM1-3575-000CN |
| Деталь: | Cable, pickup-option PCA connect |
| Парткод: | RM1-3573-000CN |
| Деталь: | ROLLER, RAIL |
| Парткод: | RC1-9231-000CN |
| Деталь: | Caster, double-lock, front |
| Парткод: | RC1-9896-000CN |
| Деталь: | Support, lock-shaft |
| Парткод: | RC1-9900-000CN |
| Деталь: | Plate, switch-cover |
| Парткод: | RC1-9901-000CN |
| Деталь: | SHAFT, LOCK |
| Парткод: | RC1-9912-000CN |
| Деталь: | ARM, LOCK |
| Парткод: | RC1-9913-000CN |
| Деталь: | BUSHING |
| Парткод: | RC1-9915-000CN |
| Деталь: | Caster, rear |
| Парткод: | RC1-9917-000CN |
| Деталь: | RAIL, CASSETTE, RIGHT |
| Парткод: | RL1-1310-000CN |
| Деталь: | RAIL, CASSETTE, LEFT |
| Парткод: | RL1-1311-000CN |
| Деталь: | Switch, button |
| Парткод: | WC2-5512-000CN |
| Деталь: | Screw, with washer, M5x12 |
| Парткод: | XA9-0912-000CN |
| Деталь: | Screw, with washer, M3x6 |
| Парткод: | XB2-8300-607CN |
| Деталь: | MOTOR ASSEMBLY |
| Парткод: | Q3938-67908 |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-6857-000CN |
| Деталь: | Arm, paper-delivery gate |
| Парткод: | RC2-1293-000CN |
| Деталь: | Swing-guide assembly |
| Парткод: | RM1-4108-000CN |
| Деталь: | Flag, paper-sensing sensor |
| Парткод: | FC5-5004-000CN |
| Деталь: | SPRING, TORSION |
| Парткод: | FC5-5005-000CN |
| Деталь: | COVER, REAR |
| Парткод: | RC2-1278-000CN |
| Деталь: | Cover, tray-connector |
| Парткод: | RC2-1279-000CN |
| Деталь: | Paper-face sensor assembly |
| Парткод: | 4G3-0934-000CN |
| Деталь: | Paper-face sensing assembly |
| Парткод: | 4G3-1624-000CN |
| Деталь: | Top-door (upper-cover) assembly |
| Парткод: | RM1-4121-000CN |
| Деталь: | Front-door assembly |
| Парткод: | RM1-4122-000CN |
| Деталь: | Middle-height cover assembly |
| Парткод: | RM1-4119-000CN |
| Деталь: | Left-upper cover assembly |
| Парткод: | RM1-4129-000CN |
| Деталь: | Cover, left-lower |
| Парткод: | RC2-1280-000CN |
| Деталь: | Panel, height, upper |
| Парткод: | RC2-1283-000CN |
| Деталь: | Guide, side-wall |
| Парткод: | RC2-1284-000CN |
| Деталь: | Cover, front-lower |
| Парткод: | RL1-1717-000CN |
| Деталь: | Cover, rear-lower |
| Парткод: | RL1-1718-000CN |
| Деталь: | WINDOW, LED |
| Парткод: | RC2-1734-000CN |
| Деталь: | LED-PCA assembly |
| Парткод: | RM1-4141-000CN |
| Деталь: | Link-slide assembly |
| Парткод: | 4G3-0271-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | HINGE ASSEMBLY |
| Парткод: | Q3938-67952 |
| Деталь: | Intermediate paper-transfer unit (IPTU)-driver PCA assembly |
| Парткод: | RM1-3559-000CN |
| Деталь: | Main controller PCA assembly (stapler/stacker and booklet-maker) |
| Парткод: | RM1-4139-000CN |
| Деталь: | Saddle-controller PCA assembly (booklet-maker) |
| Парткод: | RM1-4140-000CN |
| Деталь: | Front-cover assembly |
| Парткод: | RM1-3357-000CN |
| Деталь: | Front internal-cover assembly |
| Парткод: | RM1-4404-000CN |
| Деталь: | BAND, DOOR |
| Парткод: | RC1-9043-000CN |
| Деталь: | Guide, multi-purpose, upper |
| Парткод: | RC1-8526-000CN |
| Деталь: | Retainer |
| Парткод: | RC1-8511-000CN |
| Деталь: | LIMITER, TORQUE |
| Парткод: | RC1-8519-000CN |
| Деталь: | Multi-purpose paper-pickup assembly |
| Парткод: | RM1-3345-000CN |
| Деталь: | Tray 1 pickup, retard-roller kit |
| Парткод: | Q3931-67920 |
| Деталь: | Paper-feed PCA assembly (1x500-sheet) |
| Парткод: | RM1-3569-000CN |
| Деталь: | Paper-feed PCA assembly (3x500-sheet) |
| Парткод: | RM1-3569-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0137-000CN |
| Деталь: | Stack-tray assembly |
| Парткод: | RM1-4104-000CN |
| Деталь: | Approach-switch assembly |
| Парткод: | FM2-0710-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | FC5-4221-000CN |
| Деталь: | GEAR, 44T |
| Парткод: | FU5-0435-000CN |
| Деталь: | GEAR, 17T |
| Парткод: | FU5-0457-000CN |
| Деталь: | Roller, tray-guide |
| Парткод: | RU5-6035-000CN |
| Деталь: | Area-sensor PCA assembly |
| Парткод: | 4G1-1498-000CN |
| Деталь: | Tray-driver PCA assembly |
| Парткод: | FG3-2887-000CN |
| Деталь: | Paper-sensor assembly |
| Парткод: | FM2-0707-000CN |
| Деталь: | Area-sensor holder assembly |
| Парткод: | FM2-0709-000CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2300-142CN |
| Деталь: | Stack upper-tray assembly |
| Парткод: | RM1-4102-000CN |
| Деталь: | Saddle-motor assembly |
| Парткод: | FM2-0737-000CN |
| Деталь: | Entrance lower-guide assembly |
| Парткод: | RM1-4110-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Saddle paper-feeder assembly |
| Парткод: | RM1-4109-000CN |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FC5-3657-000CN |
| Деталь: | Hinge, front-door, 1 |
| Парткод: | FC5-4991-030CN |
| Деталь: | Hinge, front-door, 2 |
| Парткод: | FC5-4992-030CN |
| Деталь: | Rack, rail |
| Парткод: | FC5-5436-000CN |
| Деталь: | GEAR, 30T |
| Парткод: | FU5-0428-000CN |
| Деталь: | GEAR, 40T |
| Парткод: | FU5-0454-000CN |
| Деталь: | GEAR, 29T |
| Парткод: | FU5-2399-000CN |
| Деталь: | PULLEY, 20T |
| Парткод: | FU5-3086-000CN |
| Деталь: | Screw, RS stepped, M3 |
| Парткод: | FU9-9059-000CN |
| Деталь: | Cover, internal, lower (stapler/stacker only) |
| Парткод: | RC2-1351-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1386-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF2-1607-860CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-840CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF9-0748-000CN |
| Деталь: | Upper-cover lock assembly |
| Парткод: | 4G3-0210-000CN |
| Деталь: | Screw, RS, M4x8 (booklet-maker only) |
| Парткод: | XA9-0732-000CN |
| Деталь: | Stack-ejection motor assembly |
| Парткод: | 4G3-0769-000CN |
| Деталь: | CABLE, SOLENOID |
| Парткод: | FG3-2892-000CN |
| Деталь: | Shutter H.P. sensor assembly |
| Парткод: | FM2-1401-000CN |
| Деталь: | Upper-crossmember assembly |
| Парткод: | RM1-4180-000CN |
| Деталь: | Press-motor assembly |
| Парткод: | FM2-1409-000CN |
| Деталь: | Sensor/switch assembly |
| Парткод: | FM2-1417-000CN |
| Деталь: | Swing-press shaft assembly |
| Парткод: | FM2-1423-000CN |
| Деталь: | Area-sensor flag assembly |
| Парткод: | RM1-4107-000CN |
| Деталь: | Caster, universal |
| Парткод: | RC2-1315-000CN |
| Деталь: | Screw, with washer, M5x12 |
| Парткод: | XA9-0912-000CN |
| Деталь: | Inner-cover assembly |
| Парткод: | RM1-4123-000CN |
| Деталь: | Cable-mount lattice assembly |
| Парткод: | RM1-4128-000CN |
| Деталь: | Sheet, entrance-guide |
| Парткод: | FC5-5542-000CN |
| Деталь: | SOLENOID |
| Парткод: | FL2-0821-000CN |
| Деталь: | PIN |
| Парткод: | XD3-2200-102CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-142CN |
| Деталь: | Entrance-sensor flag assembly |
| Парткод: | FM2-0718-000CN |
| Деталь: | Plate, hinge-stop (booklet-maker only) |
| Парткод: | 4A3-4715-000CN |
| Деталь: | Knob (booklet-maker only) |
| Парткод: | FB3-7881-000CN |
| Деталь: | Cover, internal, lower (booklet-maker only) |
| Парткод: | RL1-1477-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | 4A3-1955-000CN |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | 4H3-0370-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | RC2-1356-000CN |
| Деталь: | Flexible-cable mount assembly |
| Парткод: | FM2-0720-000CN |
| Деталь: | Screw, TP, M3x6 (booklet-maker only) |
| Парткод: | XB6-7300-607CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | COVER, REAR |
| Парткод: | RC1-9871-000CN |
| Деталь: | COVER, LEFT |
| Парткод: | RC1-9872-000CN |
| Деталь: | Cover, front-upper |
| Парткод: | RC1-9873-000CN |
| Деталь: | Cover, right-lower |
| Парткод: | RC1-9874-000CN |
| Деталь: | Guide, paper-feed roller |
| Парткод: | RC1-9881-000CN |
| Деталь: | Stopper, right-door |
| Парткод: | RC1-9882-000CN |
| Деталь: | LEVER, LOCK |
| Парткод: | RC1-9883-000CN |
| Деталь: | Tape, door |
| Парткод: | RC1-9884-000CN |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-1331-000CN |
| Цена: | 2 500 ₽ |
| Деталь: | Cover, right-front |
| Парткод: | RL1-1322-000CN |
| Деталь: | SCREW, STEPPED |
| Парткод: | RS5-9099-000CN |
| Деталь: | CONNECTOR, DRAWER |
| Парткод: | VS1-7257-012CN |
| Деталь: | Support, PCA |
| Парткод: | VT2-0001-008CN |
| Деталь: | SADDLE, WIRE |
| Парткод: | WT2-5694-000CN |
| Цена: | 320 ₽ |
| Деталь: | SCREW, TP, M3X6 |
| Парткод: | XA9-1469-000CN |
| Деталь: | CLAMP, CABLE |
| Парткод: | WT2-5738-000CN |
| Деталь: | Right-door assembly |
| Парткод: | RM1-3538-000CN |
| Деталь: | SCREW, RS, M4X8 |
| Парткод: | XA9-1448-000CN |
| Деталь: | Paper-feed PCA assembly |
| Парткод: | RM1-3569-000CN |
| Деталь: | Cable, pickup-option drawer |
| Парткод: | RM1-3571-000CN |
| Деталь: | Cable, pickup-option door switch |
| Парткод: | RM1-3572-000CN |
| Деталь: | Cable, option-sensor PCA connect |
| Парткод: | RM1-3574-000CN |
| Деталь: | Cable, paper-pickup option |
| Парткод: | RM1-3575-000CN |
| Деталь: | Stock-box assembly |
| Парткод: | RM1-3539-000CN |
| Деталь: | ROLLER, RAIL |
| Парткод: | RC1-9231-000CN |
| Деталь: | Caster, double-lock, front |
| Парткод: | RC1-9896-000CN |
| Деталь: | Support, lock-shaft |
| Парткод: | RC1-9900-000CN |
| Деталь: | Plate, switch-cover |
| Парткод: | RC1-9901-000CN |
| Деталь: | SHAFT, LOCK |
| Парткод: | RC1-9912-000CN |
| Деталь: | ARM, LOCK |
| Парткод: | RC1-9913-000CN |
| Деталь: | BUSHING |
| Парткод: | RC1-9915-000CN |
| Деталь: | Caster, rear |
| Парткод: | RC1-9917-000CN |
| Деталь: | RAIL, CASSETTE, RIGHT |
| Парткод: | RL1-1310-000CN |
| Деталь: | RAIL, CASSETTE, LEFT |
| Парткод: | RL1-1311-000CN |
| Деталь: | Switch, button |
| Парткод: | WC2-5512-000CN |
| Деталь: | Screw, with washer, M5x12 |
| Парткод: | XA9-0912-000CN |
| Деталь: | Door, stock |
| Парткод: | RC1-9921-000CN |
| Деталь: | Screw, with washer, M3x6 |
| Парткод: | XB2-8300-607CN |
| Деталь: | Screw, tapping, pan-head, M4x10 |
| Парткод: | XB4-7401-006CN |
| Деталь: | Guide, multi-purpose, right |
| Парткод: | RL1-1283-000CN |
| Деталь: | Guide, face-down inner |
| Парткод: | RC1-8959-000CN |
| Деталь: | Rail, reverse, rear |
| Парткод: | RC1-9206-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1504-000CN |
| Деталь: | Sheet, fixing-crossmember |
| Парткод: | RC1-9232-000CN |
| Деталь: | CABLE, LASER FLEXIBLE FLAT |
| Парткод: | RK2-1354-000CN |
| Деталь: | CABLE, LASER FLEXIBLE FLAT |
| Парткод: | RK2-1355-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | RU5-2822-000CN |
| Деталь: | SPRING, TORSION |
| Парткод: | RU5-2825-000CN |
| Деталь: | CLAMP, FFC |
| Парткод: | WT2-5912-000CN |
| Деталь: | Grip-support front assembly |
| Парткод: | RM1-3225-000CN |
| Деталь: | Grip-support rear assembly |
| Парткод: | RM1-3226-000CN |
| Деталь: | Thermopile case assembly |
| Парткод: | RM1-3232-000CN |
| Деталь: | Photosensor assembly |
| Парткод: | RM1-3250-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1449-000CN |
| Деталь: | Reader rear-guide assembly |
| Парткод: | RM1-4399-000CN |
| Деталь: | FAN ASSEMBLY |
| Парткод: | RM1-3364-000CN |
| Деталь: | Scanner assembly kit with 1 scanner assembly and service document |
| Парткод: | Q3931-67907 |
| Деталь: | SCREW, RS, M3X6 |
| Парткод: | XA9-1495-000CN |
| Деталь: | Reader front-guide assembly |
| Парткод: | RM1-4398-000CN |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | Holder, environment-sensor |
| Парткод: | RC1-9324-000CN |
| Деталь: | SENSOR UNIT, HUMIDITY |
| Парткод: | RK2-2376-000CN |
| Деталь: | Holder, scanner-thermistor |
| Парткод: | RC1-9260-000CN |
| Деталь: | DUCT, SCANNER |
| Парткод: | RC1-9334-000CN |
| Деталь: | THERMISTOR UNIT |
| Парткод: | RK2-1363-000CN |
| Деталь: | Connector, snap-tight |
| Парткод: | VS1-7177-002CN |
| Деталь: | Interlock-switch assembly |
| Парткод: | RM1-3589-000CN |
| Деталь: | Right-assist assembly |
| Парткод: | RM1-4397-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Inner side-plate assembly |
| Парткод: | 4G3-0671-000CN |
| Деталь: | LIMITER, TORQUE |
| Парткод: | FC5-3657-000CN |
| Деталь: | Hinge, front-door, 1 |
| Парткод: | FC5-4991-030CN |
| Деталь: | Hinge, front-door, 2 |
| Парткод: | FC5-4992-030CN |
| Деталь: | Rack, rail |
| Парткод: | FC5-5436-000CN |
| Деталь: | GEAR, 30T |
| Парткод: | FU5-0428-000CN |
| Деталь: | GEAR, 40T |
| Парткод: | FU5-0454-000CN |
| Деталь: | GEAR, 29T |
| Парткод: | FU5-2399-000CN |
| Деталь: | PULLEY, 20T |
| Парткод: | FU5-3086-000CN |
| Деталь: | Screw, RS stepped, M3 |
| Парткод: | FU9-9059-000CN |
| Деталь: | Cover, internal, lower (stapler/stacker only) |
| Парткод: | RC2-1351-000CN |
| Деталь: | SCREW, RS, M3X8 |
| Парткод: | XA9-1386-000CN |
| Деталь: | RING, E |
| Парткод: | XD9-0136-000CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF2-1607-860CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-1608-840CN |
| Деталь: | BELT, TIMING, COGGED |
| Парткод: | XF9-0748-000CN |
| Деталь: | Upper-cover lock assembly |
| Парткод: | 4G3-0210-000CN |
| Деталь: | Screw, RS, M4x8 (booklet-maker only) |
| Парткод: | XA9-0732-000CN |
| Деталь: | Stack-ejection motor assembly |
| Парткод: | 4G3-0769-000CN |
| Деталь: | CABLE, SOLENOID |
| Парткод: | FG3-2892-000CN |
| Деталь: | Shutter H.P. sensor assembly |
| Парткод: | FM2-1401-000CN |
| Деталь: | Upper-crossmember assembly |
| Парткод: | RM1-4180-000CN |
| Деталь: | Press-motor assembly |
| Парткод: | FM2-1409-000CN |
| Деталь: | Sensor/switch assembly |
| Парткод: | FM2-1417-000CN |
| Деталь: | Swing-press shaft assembly |
| Парткод: | FM2-1423-000CN |
| Деталь: | Area-sensor flag assembly |
| Парткод: | RM1-4107-000CN |
| Деталь: | Caster, universal |
| Парткод: | RC2-1315-000CN |
| Деталь: | Screw, with washer, M5x12 |
| Парткод: | XA9-0912-000CN |
| Деталь: | Inner-cover assembly |
| Парткод: | RM1-4123-000CN |
| Деталь: | Cable-mount lattice assembly |
| Парткод: | RM1-4128-000CN |
| Деталь: | Sheet, entrance-guide |
| Парткод: | FC5-5542-000CN |
| Деталь: | SOLENOID |
| Парткод: | FL2-0821-000CN |
| Деталь: | PIN |
| Парткод: | XD3-2200-102CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2200-142CN |
| Деталь: | Entrance-sensor flag assembly |
| Парткод: | FM2-0718-000CN |
| Деталь: | Plate, hinge-stop (booklet-maker only) |
| Парткод: | 4A3-4715-000CN |
| Деталь: | Knob (booklet-maker only) |
| Парткод: | FB3-7881-000CN |
| Деталь: | Cover, internal, lower (booklet-maker only) |
| Парткод: | RL1-1477-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | 4A3-1955-000CN |
| Деталь: | CLUTCH, ELECTROMAGNETIC |
| Парткод: | 4H3-0370-000CN |
| Деталь: | Plate, grounding (booklet-maker only) |
| Парткод: | RC2-1356-000CN |
| Деталь: | Flexible-cable mount assembly |
| Парткод: | FM2-0720-000CN |
| Деталь: | Screw, TP, M3x6 (booklet-maker only) |
| Парткод: | XB6-7300-607CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | Arm, adjustment, front |
| Парткод: | 4A3-1763-000CN |
| Деталь: | Arm, adjustment, rear |
| Парткод: | 4A3-1764-000CN |
| Деталь: | Plate, rotation |
| Парткод: | 4A3-1779-000CN |
| Деталь: | LEVER, STOPPER |
| Парткод: | 4A3-1782-000CN |
| Деталь: | Roller, folding |
| Парткод: | 4A3-1783-000CN |
| Деталь: | GEAR, 50T |
| Парткод: | 4S3-0171-000CN |
| Деталь: | BEARING, BALL, 6902ZZNR |
| Парткод: | 4S3-1050-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | 4S3-2116-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | 4S3-2117-000CN |
| Деталь: | Flag, roller |
| Парткод: | FB3-7925-030CN |
| Деталь: | Deflector |
| Парткод: | FB3-7928-020CN |
| Деталь: | Rack, rear |
| Парткод: | FB3-7934-000CN |
| Деталь: | Rack, front |
| Парткод: | FB3-7967-000CN |
| Деталь: | HOLDER, ROLLER, 2 |
| Парткод: | FB3-7973-000CN |
| Деталь: | FLAG, SENSOR |
| Парткод: | FB3-7979-000CN |
| Деталь: | SPRING, TORSION |
| Парткод: | FB3-7980-000CN |
| Деталь: | Deflector |
| Парткод: | FB5-2697-000CN |
| Деталь: | FLAG, SENSOR |
| Парткод: | FB5-5937-020CN |
| Деталь: | Claw, latch, right |
| Парткод: | FC5-5021-000CN |
| Деталь: | PULLEY, 30T |
| Парткод: | FS5-3576-000CN |
| Деталь: | Pulley, 39T |
| Парткод: | FS5-3577-000CN |
| Деталь: | Gear, 16T/33T |
| Парткод: | FS6-0822-000CN |
| Деталь: | GEAR, 16T |
| Парткод: | FS6-0823-000CN |
| Деталь: | Gear, 16T/56T |
| Парткод: | FS6-0829-000CN |
| Деталь: | GEAR, 16T |
| Парткод: | FS6-0830-000CN |
| Деталь: | SPRING, TENSION |
| Парткод: | FS6-2582-000CN |
| Деталь: | Photo interrupter, TLP1242 |
| Парткод: | WG8-5593-000CN |
| Деталь: | BELT, TIMING |
| Парткод: | XF2-3837-340CN |
| Деталь: | Cable, saddle-unit |
| Парткод: | 4G1-2283-000CN |
| Деталь: | Guide-motor assembly |
| Парткод: | 4G3-0725-000CN |
| Деталь: | Plate, tension |
| Парткод: | FF5-5805-040 |
| Деталь: | Rear-end sensor assembly |
| Парткод: | FM2-0763-000CN |
| Деталь: | Delivery-switch mount assembly |
| Парткод: | FM2-1639-000CN |
| Деталь: | Upper delivery-guide assembly |
| Парткод: | RM1-4131-000CN |
| Деталь: | Saddle-controller PCA assembly |
| Парткод: | RM1-4140-000CN |
| Деталь: | Saddle paper-delivery assembly |
| Парткод: | RM1-4130-000CN |
| Деталь: | Motor-mount assembly |
| Парткод: | 4G3-0670-000CN |
| Деталь: | Saddle-guide assembly |
| Парткод: | FM2-0756-000CN |
| Деталь: | Inner side-plate assembly |
| Парткод: | 4G3-0671-000CN |
| Деталь: | Saddle-stapler assembly |
| Парткод: | RM1-4178-000CN |
| Деталь: | Ring, C, external |
| Парткод: | XD2-3100-152CN |
| Деталь: | PIN, DOWEL |
| Парткод: | XD3-2300-202CN |
| Деталь: | ROD |
| Парткод: | Q3938-67911 |
| Деталь: | Flat cable, 28, 940, A |
| Парткод: | Q3938-67912 |
| Деталь: | Flat cable, 28, 970, B |
| Парткод: | Q3938-67913 |
| Деталь: | Sensor base |
| Парткод: | Q3938-67914 |
| Деталь: | Rubber glass guide |
| Парткод: | Q3938-67915 |
| Деталь: | Motor-mount assembly |
| Парткод: | 4G3-0670-000CN |
| Деталь: | End cover (cap) front assembly |
| Парткод: | Q3938-67946 |
| Деталь: | Separation-pad assembly (part of the ADF maintenance kit) |
| Парткод: | Q3938-67949 |
| Деталь: | Intermediate paper-transfer unit (IPTU)-driver PCA assembly |
| Парткод: | RM1-3559-000CN |
| Деталь: | MOTOR, STEPPING, DC |
| Парткод: | RK2-1320-000CN |
| Цена: | 1 300 ₽ |
| Деталь: | FLANGE, PULLEY |
| Парткод: | RC1-9620-000CN |
| Деталь: | CABLE, DRAWER |
| Парткод: | RM1-3561-000CN |
| Деталь: | Cover, assist, right |
| Парткод: | RC1-9706-000CN |
| Деталь: | Plate, assist-arm cap |
| Парткод: | RC1-9695-000CN |
| Деталь: | Cover, rear-upper |
| Парткод: | RC1-9703-000CN |
| Деталь: | Belt, paper-feed, cogged |
| Парткод: | RC1-9674-000CN |
| Деталь: | Pulley/gear, 22T |
| Парткод: | RU5-0868-000CN |
| Деталь: | Screw, M4x14 |
| Парткод: | XA9-1292-000CN |
| Деталь: | CABLE, DRAWER |
| Парткод: | RM1-3560-000CN |
| Деталь: | Screw, RS M3X8 |
| Парткод: | XA9-1500-000CN |
| Деталь: | Side-cover assembly |
| Парткод: | RM1-3683-000CN |
| Деталь: | Drive-belt assembly |
| Парткод: | RM1-3684-000CN |
| Деталь: | Fin-lock assembly |
| Парткод: | RM1-3685-000CN |
| Деталь: | Arm, auxiliary |
| Парткод: | RL1-1272-000CN |
| Деталь: | SCREW, B, M4X8 |
| Парткод: | XA9-1277-000CN |
| Деталь: | CABLE, MOTOR |
| Парткод: | RM1-3563-000CN |
| Деталь: | CABLE, MOTOR |
| Парткод: | RM1-3564-000CN |
| Деталь: | Guide, cable, 2 |
| Парткод: | RC1-9688-000CN |
| Деталь: | BUSHING |
| Парткод: | RC1-4585-000CN |
| Деталь: | FAN ASSEMBLY |
| Парткод: | RM1-4394-000CN |
| Деталь: | SHEET, BLANKING |
| Парткод: | RC1-9687-000CN |
| Деталь: | Cover, assist, left |
| Парткод: | RC1-9705-000CN |
| Деталь: | Screw, machined, truss-head, M3x4 |
| Парткод: | XB1-2300-407CN |
| Деталь: | Screw, with washer, M3x6 |
| Парткод: | XB2-8300-607CN |
| Деталь: | Separation-floor assembly |
| Парткод: | Q3938-67949 |
| Деталь: | Cover pick roller (part of the ADF maintenance kit) |
| Парткод: | Q3938-67954 |
| Деталь: | Cassette-assembly kit with service document |
| Парткод: | Q3931-67918 |
| Деталь: | ADF UNIT |
| Парткод: | Q3938-67943 |
| Деталь: | PHOTO INTERRUPTER, TLP1243 |
| Парткод: | WG8-5696-000CN |
| Цена: | 350 ₽ |
| Деталь: | Multi-purpose-guide assembly |
| Парткод: | RM1-3291-000CN |
Коды ошибок
10.00.YY
10.10.YY
10.90.XY
10.xx.yy
11.XX
13.01
13.02
13.05
13.06
13.10
13.11
13.12
13.12.11
13.12.12
13.12.13
13.12.14
13.12.15
13.12.16
13.12.17
13.12.21
13.12.41
13.12.42
13.12.43
13.12.44
13.12.45
13.12.46
13.12.51
13.12.52
13.12.61
13.12.62
13.13
13.1C
13.20
13.21
13.2B
13.2C
13.2D
13.2E
13.30
13.7C
13.7D
13.7E
13.80
13.90
13.JJ.NT
13.XX.YY
20
22
30.01.02
30.01.03
30.01.06
30.01.08
30.01.14
30.01.15
30.01.18
30.01.19
30.01.25
30.01.34
30.01.39
30.01.40
30.01.41
30.01.42
30.01.43
30.01.44
30.01.45
30.01.46
40
41.3
41.5
41.X
48.01
49.XXXXX
50.1
50.2
50.3
50.4
50.5
50.7
50.8
50.9
50.A
50.B
51.1Y
51.2Y
52.00
52.10
52.20
53.10.0X
54.01
54.15
54.16
54.17
54.18
55.00.YY
55.01.YY
55.02.YY
55.03.YY
55.04.YY
55.05
56.01
56.02
57.01
57.03
57.04
57.05
57.06
57.07
57.08
57.09
59.30
59.40
59.50
59.51
59.52
59.53
59.60
59.61
59.62
59.63
59.90
59.A0
59.C0
59.F0
59.XY
60.02
60.03
60.04
60.05
60.XX
65.12.99
66.00.15
66.12.01
66.12.02
66.12.03
66.12.11
66.12.12
66.12.13
66.12.14
66.12.15
66.12.16
66.12.21
66.12.22
66.12.23
66.12.31
66.12.32
66.12.34
66.12.41
66.12.42
66.12.43
66.12.44
66.12.45
66.12.46
66.12.47
66.12.51
66.12.52
66.XY.ZZ
68.X
69.X
79.XXXX
8X.YYYY
Описание
| Error code: | 10.00.YY |
| Display: | 10.XX.YY SUPPLY MEMORY ERROR |
| Description: | The MFP cannot read or write to at least one print cartridge e-label or an e-label is missing from a print cartridge. E-label is damaged. |
| Remedy: | 1. Reinstall the print cartridge, or install a new HP print cartridge. 2. Verify that connector J97 on the DC controller PCA is firmly seated. |
| Error code: | 10.10.YY |
| Display: | 10.XX.YY SUPPLY MEMORY ERROR |
| Description: | The MFP cannot read or write to at least one print cartridge e-label or an e-label is missing from a print cartridge. MFP cannot communicate with the e-label. |
| Remedy: | 1. Reinstall the print cartridge, or install a new HP print cartridge. 2. Verify that connector J97 on the DC controller PCA is firmly seated. |
| Error code: | 10.90.XY |
| Display: | 10.90.XY REPLACE <COLOR> CARTRIDGE |
| Description: | A toner replenishment malfunction has occurred. |
| Remedy: | Replace the print cartridge. If replacing the print cartridge does not fix the problem, replace the corresponding image drum. |
| Error code: | 10.xx.yy |
| Display: | 10.xx.yy Supply Memory Error |
| Description: | The product cannot read or write to at least one print cartridge e-label, or an e-label is missing from a print cartridge. |
| Remedy: | Reinstall the print cartridge, or install a new HP print cartridge. |
| Error code: | 11.XX |
| Display: | 11.XX INTERNAL CLOCK ERROR |
| Description: | The real time clock has experienced an error. |
| Remedy: | 1. Power cycle the product to see if the message clears. 2. If possible, print a configuration page to record product information, and then perform an NVRAM initialization routine. If the initialization routine is successful, you will need to re-enter several configuration parameters (such as the page count and the serial number). 3. If the error persists, replace the formatter PCA. |
| Error code: | 13.01 |
| Display: | 13.01 Paper feed 1, Paper late jam |
| Description: | • The leading edge of the paper fed from Tray 1 stopped before reaching the registration sensor (C). • The leading edge of the paper fed from Tray 2 stopped before reaching the registration sensor (B). • The leading edge of the paper fed from Tray 3 stopped before reaching the registration sensor (A-1). • The leading edge of the paper fed from Tray 4 stopped before reaching the registration sensor (A-2). • The leading edge of the paper fed from Tray 5 stopped before reaching the registration sensor (A-3).89A |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.02 |
| Display: | 13.02 Paper Stop Jam In Tray 2 at Sensor D |
| Description: | The paper stopped at the registration sensor (D). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.05 |
| Display: | 13.05 Paper Late Jam Between Sensors D and F |
| Description: | The leading edge of the paper stopped between the registration sensor (D) and the fuser-output sensor (F). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.06 |
| Display: | 13.06 Paper Jam In Fuser |
| Description: | The paper stopped at the fuser-output sensor (F). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.10 |
| Display: | 13.10 Paper Late Jam In Duplex Area Sensors F - G |
| Description: | The leading edge of the paper stopped between the output sensor (F) and switchback sensor (G). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.11 |
| Display: | 13.11 Paper Stop Jam In Duplex Area at Sensor G |
| Description: | The paper stopped at the switchback-jam sensor (G). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.12 |
| Display: | 13.12 Paper Late Jam In Duplex Area Sensors H - D |
| Description: | The duplex refeed paper stopped between the duplexer-delivery sensor (H) and the registration sensor (D). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.12.11 |
| Display: | 13.12.11 Jam inside upper left door |
| Description: | Stapler jam. Initial jam at entry. At power-on, media was detected at SR2100 (inlet media sensor). SR2100 is located in the stapler/stacker feed assembly. SR2100 senses media entering the stapler/stacker. |
| Remedy: | 1. Open the upper left door and remove any media. 2. Open the lower left door and remove any media. 3. Check connection J2104 on the stapler/ stacker control board. 4. Remove the stapler/stacker feed assembly and perform the following tasks. - Remove any media from SR2100. - Check the operation of the sensor flag and sensor-flag spring and make sure that the flag does not block the sensor. If the flag or the spring is damaged, replace the stapler/stacker feed assembly. - Clean SR2100 by blowing air gently into the sensing area. Check the sensor for correct mounting, cable connection, and alignment with the sensor flag. If the sensor is damaged or nor working, replace the sensor. - Check operation of the drive gears and belts at the rear of the stapler/ stacker feed assembly. Turning any of the gears should turn all of the rollers in the assembly. If the gears or belts are not working, replace the stapler/stacker feed assembly. 5. If, after performing the previous steps, the problem persists, replace the stapler/stacker control board. |
| Error code: | 13.12.12 |
| Display: | 13.12.12 |
| Description: | Finisher delay jam at PI33. The engine signals the finisher that paper is about to enter the finisher from the IPTU. The finisher`s upper-feed-path-entry sensor (PI33), which detects paper entering the finisher, does not detect the paper within the expected time period triggering the error. |
| Remedy: | Open the IPTU and the finisher top door and check the following items: • If media is found in the IPTU but has not reached the finisher, perform the following steps: • Remove and then reinstall the IPTU. Make sure that the connector is fully seated and that the IPTU is securely fastened. • If the error persists, replace the IPTU. • If media is jammed at the exit point of the IPTU (prior to entering the finisher), perform the following steps: • Verify that the finisher is securely fastened to the engine. • Make sure that the finisher and IPTU are correctly aligned. Adjust the finisher castors to obtain a uniform gap between the finisher and the engine. The engine-tofinisher gap must be the same at the bottom and the top so that the finisher is parallel to the engine. With the engine-to-finisher gap correct, make sure that the finisher paper path entry point is aligned with the IPTU exit point. • Check the finisher entry point guides for damage. • Verify that the finisher rollers are turning before the media leaves the IPTU. If the rollers are not turning, test motor M9 by using the finisher component test from the controlpanel display. If the motor does not activate during the test, check the connectors for motor M9 (inlet motor). Make sure that connector J705 is fully seated on the stacker controller PCA. If the error persists, replace motor M9 or the saddle paper-feeder assembly. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. • If media is found in the finisher but has not reached sensor PI33, perform the following steps: • Check the upper and lower guides and rollers in the paper path for damage. • Make sure that the media diverter gate (saddle-stitch flapper) is not blocking the paper path. • If media is found in the finisher covering sensor PI33 (the sensor is not detecting the media), perform the following steps: • Check the sensor for obstructions. Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body• Make sure that the lower end of the flag is not damaged and is correctly positioned to activate the sensor. • Make sure that the sensor is securely fastened to the chassis. • Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. • Verify that the wiring at the sensor is not damaged and that the intermediate connector J1007 and connector J708 on the stacker controller PCA are fully seated. Replace the sensor if necessary. • Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. |
| Error code: | 13.12.13 |
| Display: | 13.12.13 |
| Description: | Finisher stay jam at PI33. Finisher`s upper-feed-path-entry sensor (PI33) is remaining activated longer than expected, suggesting that paper has jammed at the sensor. |
| Remedy: | Control panel diagnostics: none 1. Remove any media in the upper paper path that might be activating sensor PI33. 2. Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. 3. Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. 4. Verify that the wiring at the sensor is not damaged and that the connector J708 on the stacker controller PCA is fully seated. |
| Error code: | 13.12.14 |
| Display: | 13.12.14 |
| Description: | Finisher delay jam at PI34. Upper-paper-path-entry sensor (PI33) has signaled that paper has passed but upperpaper- path exit sensor PI34 does not actuate within the expected time, suggesting that the paper has jammed between PI33 and PI34 in the upper paper path. |
| Remedy: | Control panel diagnostics: none 1. Remove any media jammed in the upper paper path between sensor PI33 and sensor PI34. 2. Check the paper path between sensor PI33 and sensor PI34 for obstructions that may be preventing the media from reaching PI34. 3. Verify that the PI34 sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. 4. Make sure that sensor PI34 is securely fastened to the chassis and wiring is properly connected to sensor. NOTE: Sensor PI34 is located on the front frame of the finisher, directly over the primary stapler. 5. Verify that the wiring at the sensor is not damaged and that the connector J707 on the stacker controller PCA is fully seated. 6. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. |
| Error code: | 13.12.15 |
| Display: | 13.12.15 |
| Description: | Finisher stay jam at PI34 Finisher`s upper-paper-path-exit sensor (PI34) remains activated longer than expected suggesting that paper has jammed at the sensor. |
| Remedy: | Control panel diagnostics: M31 (entrance motor), SL32 (buffer roller solenoid), and SL33 (output roller solenoid) 1. Remove any media in the upper paper path that might be activating sensor PI34. 2. Carefully clean the sensor body, by gently blowing clean air across the sensor to remove dust and debris. 3. Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. 4. Lift-swing-guide assembly at the paperexit area to output bins and inspect for jammed paper, obstructions, or damage. 5. Run a diagnostic through the engine control panel and turn on M31 (entrance motor) to observe gear rotations on the upper-rear frame of the finisher. Ensure that the first-delivery rollers and buffer rollers that pass paper to and from PI34 are rotating. 6. Test SL32 (buffer-roller solenoid) and SL33 (output-roller solenoid) using the control panel diagnostics. 7. Check wiring from sensor PI34 to stacker-control board connector J707 for damage. 8. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. |
| Error code: | 13.12.16 |
| Display: | 13.12.16 |
| Description: | Finisher jam: door opened during staple/ stacking operation While the machine is printing, upper-door (open/close) sensor (PI31) or front-door (open/close) sensor (PI32) or the front-door (open/close) switch (MSW31) has signaled that one of the doors has been opened, suggesting that there may now be paper found in the upper paper path. |
| Remedy: | Control panel diagnostics: PI31 (top-door sensor), PI32 (front door sensor) Booklet maker only: check PI3 (Booklet Door 1 Sensor) (booklet-delivery door) 1. Make sure that the doors properly open and close and stay in the fully closed position. If the front door is not closing tightly at the top, it will not activate the door switch. If necessary, adjust the alignment of the front door by opening the door and carefully twisting it. 2. Verify that the sensor-activation arms on the doors are not damaged. 3. Make sure that the front-door sensor PI32 and switch MSW31 and top-door sensor PI31 are not obstructed. 4. Make sure that the arm on front-door switch MSSW31 is not bent or damaged. 5. Make sure that sensor PI32 and switch MSSW31 are securely fastened to the chassis. 6. Test sensor PI31 (upper-door sensor) and sensor PI32 (front-door sensor) by using the finisher component tests from the control-panel display. NOTE: For finishers with a booklet maker, also test sensor PI3 (bookletdoor- 1 sensor). |
| Error code: | 13.12.17 |
| Display: | 13.12.17 |
| Description: | Engine to finisher timing jam: unexpected arrival of paper to finisher Upper-paper-path entry sensor (PI33) has detected paper before a signal from the engine has been received, indicating that paper is being delivered from the IPTU to the finisher. |
| Remedy: | Control panel diagnostics: none 1. Verify that the latest firmware updates are installed for the engine and finisher. 2. Remove any media in the upper paper path that might be activating sensor PI33. If no media is found at PI33, proceed to step 3. If media is found at PI33, perform the following steps: • Make sure that the power/ communication cable from the IPTU to the finisher is properly connected. • Make sure that the IPTU is properly connected to the engine and that the mounting screws are tight. • Make sure that the finisher is properly grounded. • Ensure that the finisher is latched and locked to the engine by tightening the thumbscrew inside the front door. • Ensure that the groundingframe assembly (the bar with the wheel located between the engine and the finisher) is in the ?gdown?h position with the wheel touching the floor and that the grounding plate is not damaged. NOTE: The groundingframe assembly is in the ?gup?h position when the finisher is shipped. It must be lowered when the finisher is installed. • If the error persists, replace the IPTU. 3. Check for media at the finisher entrance point and at sensor PI33. If no media is found at PI33, perform the following steps: • Make sure that the finisher is properly grounded. • Ensure that the finisher is latched and locked to the engine by tightening the thumbscrew inside the front door. • Ensure that the groundingframe assembly (the bar with the wheel located between the engine and the finisher) is in the down position with the wheel touching the floor and that the grounding plate is not damaged. NOTE: The groundingframe assembly is in the up position when the finisher is shipped. It must be lowered when the finisher is installed. • Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. • Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. • Verify that the wiring at the sensor is not damaged and that the connector J708 on the stacker controller PCA is fully seated. 4. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. |
| Error code: | 13.12.21 |
| Display: | 13.12.21 |
| Description: | Finisher upper stapler (stapler 1) staple jam. When the staple motor (M41) is rotated forward, the staple home-position sensor (PI5) does not turn back on after the prescribed time has elapsed after it goes off, and the staple home-position sensor (PI50) turns on within the prescribed time after the staple motor (M41) is rotated backwards. |
| Remedy: | Control panel diagnostics: none 1. Check the stapler unit for jammed staples. 2. Check the stapler unit for loose staples and paper dust. 3. Inspect the stapler unit for damage. 4. Remove the stapler cartridge and make sure HP-approved staples are being used. 5. Verify that the wiring at the stapler unit and the connector are not damaged. 6. Install new staple cartridge and retest. 7. If the error persists, replace the stapler unit. |
| Error code: | 13.12.41 |
| Display: | 13.12.41 |
| Description: | Finisher: Paper detected in the bookletmaking portion of the finisher at engine power on. Occurs when paper is detected by one of the sensors on the paper-sensor board (PI18, PI19, PI20), vertical-path-paper sensor (PI17), booklet-delivery sensor (PI11), paperpositioning- plate-paper sensor (PI8), or booklet-making paper-entry sensor (PI22) when engine is turned on. |
| Remedy: | Control panel diagnostics: none 1. Remove media from the booklet-maker paper path. 2. Verify that the sensor flags are not damaged, move freely, and are correctly aligned with the sensor bodies. 3. Carefully clean each sensor body by gently blowing clean air across each sensor to remove dust and debris. 4. Make sure that connectors J6, J9, J10, J13, and J21 are fully seated on the saddle-stitcher controller PCA. 5. Only if the error persists and the previous steps fail to correct the problem, replace the saddle-stitcher controller PCA. |
| Error code: | 13.12.42 |
| Display: | 13.12.42 Jam in stacker bin area |
| Description: | Stapler jam. Initial jam at exit. At power-on, media was detected at SR2103 (delivery sensor). SR2103 is located in the stapler/stacker at the exit rollers. SR2103 is the exit sensor for the stapler/stacker and senses media as the media exits the stapler/stacker into the stacker output bin. |
| Remedy: | 1. Remove any media at the exit rollers of the stapler/stacker. 2. Open the upper left door and perform the following tasks: ?? Remove any media from the paper path. - Press down on the upper portion of the green guide and remove any media from between the green guide and the stapler/stacker exit rollers. - Clean SR2100 by blowing air gently into the sensing area. Check the sensor for correct mounting, cable connection, and alignment with the sensor flag. If the sensor is damaged or nor working, replace the sensor. - Check the operation of SR2103 (delivery sensor) and the sensor flag. If the sensor or the sensor flag is not working, replace the stapler/ stacker alignment assembly. 3. If, after performing the previous steps, the problem persists, replace the stapler/stacker control board.` |
| Error code: | 13.12.43 |
| Display: | 13.12.43 |
| Description: | Finisher stay jam at booklet-making paper entry sensor (PI22) Occurs when the booklet-making paper entry sensor (PI22) remains activated longer than expected, suggesting that there is a paper jam at the sensor. |
| Remedy: | Control panel diagnostics: none 1. Remove any media in the upper paper path that might be activating sensor PI22. 2. Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. 3. Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. 4. Verify that the wiring at the sensor is not damaged. Check the intermediate connectors between sensor PI22 and connector J21 on saddle-stitcher controller PCA for damage and proper connections. Replace the sensor if necessary. |
| Error code: | 13.12.44 |
| Display: | 13.12.44 |
| Description: | Finisher delay jam at booklet making first paper sensor (PI18) Occurs when the first-paper sensor (PI18) is not activated within the expected time following the activation of the bookletmaking- paper entry sensor (PI22), suggesting that there is a paper jam in the area between PI22 and PI18. |
| Remedy: | Control panel diagnostics: M1 (Delivery Motor) Open the IPTU and the finisher top door and locate the media jam. Check the following items: • If media is found at sensor PI18, perform the following steps: • Check the sensor PI18 for damage. Replace the sensor if necessary. • Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. • Verify that the wiring from sensor PI18 to connector J10 on the saddle-stitcher controller PCA is undamaged and the connectors are fully seated. • If media is found at the roller prior to sensor PI18 in the paper path, perform the following steps: • Test motor M1 (delivery motor) by using the finisher component test from the control-panel display. • Remove the finisher rear cover. Activate motor M1 and verify that the drive gears and belts are moving. • If motor M1 does not rotate, verify that connector J5 on the saddlestitcher controller PCA is fully seated. If the error persists, replace motor M1. If motor M1 still does not rotate, replace the saddle-stitcher controller PCA. • If motor M1 does rotate but the gears and belts connected to motor M1 do not move, check for damaged components. Replace damaged components as necessary. |
| Error code: | 13.12.45 |
| Display: | 13.12.45 |
| Description: | Finisher stay jam at booklet making first paper sensor (PI18), flapper-1 paper sensor (PI19) or flapper-2 paper sensor (PI20) Occurs when PI18, PI19 or PI20 remain activated longer than expected, suggesting that there is a paper jam in the flapper 1 and 2 area of the booklet-maker section of the finisher. |
| Remedy: | Control-panel diagnostics: PI19 (flapper 1), PI20 (flapper 2), M1 (delivery motor), SL1 (flapper 1 solenoid), SL2 (flapper 2 solenoid) 1. Remove any media in the area around flapper 1 and flapper 2. 2. Check the flappers for damage. 3. Test sensor PI19 and sensor PI20 by using the finisher component test from the control-panel display. • If the sensors are faulty, perform the following steps: • Verify that the sensor flags are not damaged, move freely, and are correctly aligned with the sensor bodies. • Verify that the wiring at the sensors is not damaged and that the connector J10 on the saddle-stitcher controller PCA is fully seated. • If the error persist, replace the paper sensor PCA (which contains PI118, PI119, and PI20). 4. Test flapper 1 and flapper 2 by using the finisher component test from the controlpanel display. NOTE: To verify the proper movement of the flappers, activate SL1 and SL2 in the finisher component test. |
| Error code: | 13.12.46 |
| Display: | 13.12.46 |
| Description: | Finisher jam: door was opened during booklet-making operation. Occurs while the machine is booklet making and the booklet delivery door sensor (PI3) or the booklet paper path open/close sensor (PI3) detects that the door or paper path has been opened. Also occurs when the finisher`s front-door sensor (PI32) has been opened with paper remaining in the processing tray of the main stapler while the finisher is not operating. |
| Remedy: | Control-panel diagnostics: PI31 (top-door sensor), PI32 (front-door sensor), PI3 (booklet door 1 sensor) (booklet-delivery door) 1. Test sensor PI31, sensor PI32, and sensor PI3 by using the finisher component test from the control-panel display. 2. Make sure that the front door, top door, and booklet-delivery door properly open and close and stay in the fully closed position. If the front door is not closing tightly at the top, it will not activate the door switch. If necessary, adjust the alignment of the front door by opening the door and carefully twisting it into proper alignment. 3. Verify that the sensor-activation arms on the doors are not damaged. 4. Make sure that the sensors and frontdoor switch MSW31 are not obstructed. 5. Make sure that the arm on switch MSW31 is not bent or damaged. 6. Make sure that sensors PI31, PI32, PI9, and switch MSW31 are securely fastened to the chassis. 7. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. |
| Error code: | 13.12.51 |
| Display: | 13.12.51 |
| Description: | Finisher jam: rear booklet stapler (SW5) When the rear-staple motor (M6) is rotated forward, the staple-home-position sensor (SW5) does not turn back on after the prescribed time has elapsed after it goes off (0.4 seconds). |
| Remedy: | Control panel diagnostics: none 1. Check the rear booklet-stapler unit for jammed staples. 2. Check the rear booklet-stapler unit for loose staples. 3. Inspect the rear booklet-stitch-stapler unit for damage. 4. Verify that HP approved staples for this stapler are being used. 5. Verify that the wiring at the stapler unit and the connector are not damaged. 6. Replace the staple cartridge. NOTE: Replace both the front and rear staple cartridges at the same time so that the staple low sensors will properly detect the level of staples in the cartridges. 7. Only if the error persists and the previous steps fail to correct the problem, replace the saddle-stapler assembly. |
| Error code: | 13.12.52 |
| Display: | 13.12.52 |
| Description: | Finisher jam: front-booklet stapler (SW7) When the rear-staple motor (M7) is rotated forward, the staple home-position sensor (SW7) does not turn back on after the prescribed time has elapsed after it goes off (0.4 seconds). |
| Remedy: | Control panel diagnostics: none 1. Check the front booklet-stapler unit for jammed staples. 2. Check the front booklet-stapler unit for loose staples. 3. Inspect the front booklet-stapler unit for damage. 4. Verify that HP approved staples for this stapler are being used. 5. Verify that the wiring at the stapler unit and the connector are not damaged. 6. Replace the staple cartridge. NOTE: Replace both the front and rear cartridges at the same time so that the staple low sensors will properly detect the level of staples in the cartridges. 7. Only if the error persists and the previous steps fail to correct the problem, replace the saddle-stapler assembly. |
| Error code: | 13.12.61 |
| Display: | 13.12.61 |
| Description: | Finisher delay jam at the booklet-delivery sensor (PI11) Occurs when the folded booklet exits the folding rollers and does not reach the bookletdelivery sensor (PI11) within the expected time. |
| Remedy: | Control panel diagnostics: none 1. Check the folder roller area for a jam or media wrapped around the rollers. 2. Check sensor PI11 for damage. 3. Make sure that the sensor is not obstructed. 4. Make sure that sensor PI11 is securely fastened to the chassis. |
| Error code: | 13.12.62 |
| Display: | 13.12.62 |
| Description: | Finisher stay jam at the booklet-delivery sensor (PI11) or the vertical-paper-path sensor (PI17) Occurs when the booklet-delivery sensor (PI11) remains activated longer than expected after sensing the arrival of the new booklet from the folding rollers. Also occurs when the vertical-paper-path sensor (PI17) remains activated longer than expected after the paper has already passed through the folding rollers and is now detected by the booklet-delivery sensor (PI11). |
| Remedy: | Control panel diagnostics: M2 (Folding motor) 1. Check the folder roller area for a jam. 2. Test the folding motor (M2) by using the finisher component test from the control-panel display. • Remove the finisher rear cover before starting the test and make sure that the folding rollers are rotating when motor M2 is on. 3. Check sensor PI11 and PI17 for damage. 4. Make sure that the sensors are not obstructed. 5. Make sure that sensor PI11 and sensor PI17 are securely fastened to the chassis. |
| Error code: | 13.13 |
| Display: | 13.13 Paper Stop Jam In Duplex Area Sensors G - H |
| Description: | The duplex refeed paper stopped between the switchback sensor (G) and the duplexerdelivery sensor (H). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.1C |
| Display: | 13.1C Fuser Wrap Jam, Paper in Fuser |
| Description: | The paper is wrapping at the fuser. |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.20 |
| Display: | 13.20 - Jam inside rear bin Clear jam then open and close front door |
| Description: | Media is jammed in the output bin. |
| Remedy: | Open the rear output bin and gently remove the jammed media. Follow the instructions in the onscreen dialog box. |
| Error code: | 13.21 |
| Display: | 13.21 Door Open Jam |
| Description: | The paper position is unknown. |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.2B |
| Display: | 13.2B Paper Stop Jam In Output Accessory Bridge |
| Description: | The paper stopped before reaching IPTU sensor 1 (K). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.2C |
| Display: | 13.2C Paper Late Jam in Output Accessory Bridge (1) |
| Description: | The paper stopped between IPTU sensor 1 (K) and IPTU sensor 3 (M). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.2D |
| Display: | 13.2D Paper Late Jam in Output Accessory Bridge (2) |
| Description: | The paper stopped in the path along IPTU sensor 1 (K), IPTU sensor 2 (L), and IPTU sensor 3 (M). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.2E |
| Display: | 13.2E Paper Late Jam Near Fuser at Sensors F - J |
| Description: | The paper stopped between the fuser-output sensor (F) and the output-bin-full sensor (J). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.30 |
| Display: | 13.30 Paper Late Jam, Jam In Cassette |
| Description: | • The leading edge of the paper fed from Tray 1 stopped before reaching the registration sensor (D). • The leading edge of the paper fed from Tray 2 stopped before reaching the registration sensor (D). • The leading edge of the paper fed from Tray 3 stopped before reaching the registration sensor (D). • The leading edge of the paper fed from Tray 4 stopped before reaching the registration sensor (D). • The leading edge of the paper fed from Tray 5 stopped before reaching the registration sensor (D). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.7C |
| Display: | 13.7C Delivery Delay Jam 1 |
| Description: | There is a delay in reaching the first IPTU sensor. |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.7D |
| Display: | 13.7D Delivery Delay Jam 2 |
| Description: | There is a delay in reaching the last IPTU sensor. |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.7E |
| Display: | 13.7E Delivery Delay Jam 3 |
| Description: | There is a delay in reaching the output rollers from the fuser. |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.80 |
| Display: | 13.80 External Output Device Paper Jam |
| Description: | There is a delivery jam on the IPTU between the first and last sensor. |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.90 |
| Display: | 13.90 Non-specific Paper Jam |
| Description: | The leading edge of the paper is at the registration sensor (D). |
| Remedy: | Follow the onscreen instructions to locate and remove the paper or obstruction. |
| Error code: | 13.JJ.NT |
| Display: | 13.JJ.NT PAPER JAM OPEN INPUT TRAYS |
| Description: | A jam has occurred in an input tray. |
| Remedy: | 1. Open the top cover. 2. Remove the print cartridge and any paper. 3. Reinstall the print cartridge and close the top cover. 4. Close all trays. |
| Error code: | 13.XX.YY |
| Display: | 13.XX.YY - Remove Tray 2 Clear jam then touch OK |
| Description: | Media is jammed in the duplex area. |
| Remedy: | Follow the instructions in the onscreen dialog box. |
| Error code: | 20 |
| Description: | Vertical image or label drift |
| Causes: | The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media. |
| Remedy: | Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation. |
| Error code: | 22 |
| Description: | Loss of printing registration on labels. Excessive vertical drift in top-of-form registration. |
| Causes: | The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly. |
| Remedy: | Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58. |
| Error code: | 30.01.02 |
| Display: | 30.01.02 ADF paper jam |
| Description: | Scanner calibration failure The scanner calibration failed. |
| Remedy: | 1. Turn the product off, and then on again. 2. After the product warms up, repeat the calibration process. Device Maintenance / Calibrate-Cleaning / Calibrate Scanner 3. If the error persists, clean the scanner glass and calibration strips. NOTE: Dust might appear on the underside of the glass, but this cannot be cleaned. a. Press the power button to turn the product off, and then disconnect the power cable from the electrical outlet. b. Open the scanner lid. c. Use a soft, lint-free cloth moistened with water to clean the calibration white strips and reflector plate (see call-outs). Also clean the document feeder glass, flatbed glass and plastic lid backing. NOTE: If needed, lens cleaner or nonabrasive glass cleaner can be applied to the cloth before cleaning the glass. Spray only onto the cloth and not directly onto the glass or device. Do not spray water or glass cleaner on the glass as it can seep under it and possibly damage the printer. Do not use abrasives, acetone, benzene, ethyl alcohol, or carbon tetrachloride on the glass; these can damage it and/or leave residue on the glass resulting in degraded copy/scan quality. 4. If the error persists, replace the Integrated Scanning Assembly (ISA). |
| Error code: | 30.01.03 |
| Display: | 30.01.03 Pick error |
| Description: | The document feeder sensors failed to detect a successful pick. |
| Remedy: | - Open the ADF feeder and remove the jammed media. Close the ADF feeder. - Reload the document and press Start. - If the error persists, run a sensors diagnostic test to verify that the skew front and skew back sensors are functioning correctly. - Verify that the pickup roller, the feed roller assembly, the separation belt assembly, and the registration roller assembly are clean and undamaged. |
| Error code: | 30.01.06 |
| Display: | 30.01.06 |
| Description: | Scanner Fan failure. Scanner fan error. The Copy, Fax and Send options will be grayed out or not present on the control panel and message will be posted in event log. |
| Remedy: | 1. Turn the product off, and then on again. 2. During the product initialization sequence, listen to the fan to determine if it is operating. 3. the error persists, turn the product off and then check the fan wire-harness connectors. 4. If the error persists, replace the scanner control board (SCB). 5. Replace the integrated scanning assembly (ISA). |
| Error code: | 30.01.08 |
| Display: | 30.01.08 Home position error |
| Description: | Home position error The scanner optic failed to return to the home position. |
| Remedy: | 1. Turn the product off, and then on again. 2. Observe the movement of the optics assembly. 3. If the error persists, run the scanner motor test under component test. Administration/ Troubleshooting/Scanner tests/Flatbed motor test 4. If issue still remains and firmware has been upgraded replace scanner control board (SCB). IMPORTANT: Check all cables on SCB for proper connection and seating before replacing any parts and test. 5. If the error persists, replace the integrated scanning assembly (ISA). |
| Error code: | 30.01.14 |
| Display: | 30.01.14 Scan system EEPROM error |
| Description: | Scan system EEPROM error Scanner control board (SCB) EEPROM error. |
| Remedy: | 1. Turn the product off, and then on again.2. Ensure all connectors on the SCB are connected and properly seated.3. Ensure the MFP has at latest SCB firmware version.4. Replace the SCB. |
| Error code: | 30.01.15 |
| Display: | 30.01.15 Scanner error |
| Description: | Scanner error Scanner did not initialize (internal error). The scanner failed to be initialized due to an internal error. |
| Remedy: | 1. Turn the product off, and then on again.2. Verify that all covers are installed correctly and that the ADF and ADF jam cover are closed.3. Check all sensors on the scanner to ensure they are not blocked.4. Look through the vents on back of scanner check to see if GREEN SCB LEDs are lit.5. Check all connections for SCB to print engine and make sure they are properly seated.6. Replace the SCB. |
| Error code: | 30.01.18 |
| Display: | 30.01.18 Scanner Error |
| Description: | Scanner Error Scanner internal optical sensor error. |
| Remedy: | 1. Turn the product off, and then on again.2. Make sure that all the connectors on the SCB are properly seated.3. Make sure that the MFP has the latest SCB firmware version.4. Replace the SCB.5. If the error persists, replace the integrated scanning assembly (ISA) |
| Error code: | 30.01.19 |
| Display: | 30.01.19 Scanner lamp error |
| Description: | Scanner lamp error Scanner internal lamp sensor error. |
| Remedy: | 1. Turn the product off, and then on again.2. Determine if the scanner lamp turns on and off approximately 12 second after the product turns on.3. Test the lower lamp using the scanner test located in the Diagnostics menu.4. Re-seat the interconnect cables between the optical carriage and the SCB.5. Replace the integrated scanning assembly (ISA) |
| Error code: | 30.01.25 |
| Display: | 30.01.25 Scanner failure |
| Description: | The copy-process board (CPB) failed. |
| Remedy: | 1. Turn the product off and then on. 2. Check the CPB LED. 3. Verify that the CPB connections are correct. 4. Verify the cable from the scanner to the formatter is not plugged in backwards. 5. Replace the CPB. |
| Error code: | 30.01.34 |
| Display: | 30.01.34 Scan failure |
| Description: | Scanner initialization failed, and the copyprocessor board (CPB) is not communicating with the scanner-controller board (SCB). |
| Remedy: | - Turn the product off, and then on. - Check the scanner controller board LEDs. - Check the connections to the scanner controller board. - Replace the scanner controller board. |
| Error code: | 30.01.39 |
| Display: | 30.01.39 Scanner failure |
| Description: | There was an AFE1 (analog front-end) failure. |
| Remedy: | 1. Turn the product off and then on. 2. Check the flat cables on the SCB. 3. Check the LEDs on the SCB. 4. Replace the SCB. 5. Replace the scanner |
| Error code: | 30.01.40 |
| Display: | 30.01.40 Scanner failure |
| Description: | The scanner AFE 2 failed. |
| Remedy: | 1. Turn the product off and then on. 2. Check the flat cables on the SCB. 3. Check the LEDs on the SCB. 4. Replace the SCB. 5. Replace the scanner. |
| Error code: | 30.01.41 |
| Display: | 30.01.41 Scanner error |
| Description: | Scanner error. The formatter lost connections with the SCB or communication was corrupted. |
| Remedy: | 1. Turn the product off, and then on. 2. Remove and reinstall the formatter making to verify it is properly seated. 3. Upgrade the firmware. 4. Verify that all cables are connected to the product and to the interconnect board / formatter and SCB. 5. Verify that the scanner control board (SCB) has power. 6. Replace the scanner control board (SCB). 7. Replace the formatter. |
| Error code: | 30.01.42 |
| Display: | 30.01.42 Scanner error |
| Description: | Scanner error Internal product communication error. |
| Remedy: | 1. Turn the product off, and then on again.2. If the error persists, turn the product off, and then check all scanner control board (SCB) connectors are fully seated.3. If this error occurs after a formatter, fax card or hard disk has been replaced, check that the formatter connectivity LED (smile face icon on the formatter) is illuminated. Check the fax card for proper seating on the formatter. (If fax card is not properly seated it can prevent the formatter from seating properly in the product. 4. Verify that all cables are connected to the product and to the interconnect board / formatter and SCB. 5. If the error persists, replace the scanner control board (SCB). |
| Error code: | 30.01.43 |
| Display: | 30.01.43 Scanner memory failure |
| Description: | Scanner memory failure Scan memory error. |
| Remedy: | 1. Turn the product off, and then on again. 2. If the error persists, turn the product off, and then re-seat the formatter. 3. If the error persists, replace the formatter. |
| Error code: | 30.01.44 |
| Display: | 30.01.44 |
| Description: | Copy processor (CPB) / scanner control board (SCB) communication error |
| Remedy: | 1. Turn the product off, and then on again. 2. If the error persists, turn the product off, and then check the scanner cable. 3. Upgrade the firmware. 4. If the error persists, turn the product off, and then re-seat the formatter. 5. If the error persists, replace the scanner control board (SCB) or the formatter. |
| Error code: | 30.01.45 |
| Display: | 30.01.45 |
| Description: | Internal copy processor board (CPB) communication error. CPB code assertion error for the copy processor board firmware. |
| Remedy: | 1. Turn the product off, and then on again. 2. If the error persists, turn the product off, and then re-seat the formatter. 3. Upgrade the firmware. 4. If the error persists, replace the scanner control board (SCB). 5. If the error persists, replace the formatter. |
| Error code: | 30.01.46 |
| Display: | 30.01.46 Scanner Error |
| Description: | Scanner Error The firmware cannot find the copy processor board (CPB). |
| Remedy: | 1. Turn the product off, and then on again. 2. If the error persists, turn the product off, and then re-seat the formatter. 3. If the error persists, replace the scanner control board (SCB). |
| Error code: | 40 |
| Display: | Scanner locked |
| Description: | 10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run. |
| Causes: | 1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors. |
| Remedy: | Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board. |
| Error code: | 41.3 |
| Display: | 41.3 UNEXPECTED SIZE IN TRAY <X> |
| Description: | You have configured the tray for a different size of paper than the print job requires. NOTE: This error can be caused by a multi feed problem. Open, and then close, the cartridge door to clear the error message. If the error persists, and the tray is correctly configured, try cleaning the Tray 1 pickup roller (or you might have to replace the roller). |
| Remedy: | 1. Reload the tray with the correct paper size. 2. Make sure the paper size that is specified in the software program, the printer driver, and the control panel are all the same. 3. Press the OK button and scroll to the TRAY <X> SIZE = <Size> option. Reconfigure the size in a tray to match the size required for the print job. 4. If the error does not clear, turn the product off and then on. 5. If the message persists, contact an HPauthorized service or support provider. |
| Error code: | 41.5 |
| Display: | 41.5 UNEXPECTED TYPE IN TRAY X |
| Description: | The device senses a different media type than what is configured in the tray. |
| Remedy: | 1. Press "OK" to print from a different tray. 2. To print from the current tray, load the tray with the size and type indicated. Ensure that all trays are configured correctly before printing again |
| Error code: | 41.X |
| Display: | 41.X ERROR |
| Description: | A temporary printing error occurred. |
| Remedy: | 1. Press OK to see if the page will print. If necessary, turn the product off and then on. 2. Verify that the loaded paper meets HP specifications. If pages stick together, the paper detect sensors will detect a sheet of paper longer than what is expected in the product. 3. Verify that all paper size settings on the control panel, in the print driver settings, and in the software program match. 4. Verify that the correct size paper is loaded in the input tray. |
| Error code: | 48.01 |
| Display: | 48.01 TRANSFER UNIT ERROR |
| Description: | The transfer belt has dislocated during printing. |
| Remedy: | Turn product off then on. |
| Error code: | 49.XXXXX |
| Display: | 49.XXXXX ERROR |
| Description: | A critical firmware error has occurred. |
| Remedy: | 1. Turn the device off and then on. 2. Try to determine whether the error occurs intermittently, while printing, or when turning on the device. 3. If the error appears while printing, determine whether it occurs when printing from a specific computer, a specific application, or a specific file. If all other computers, applications, or files can print without the error, then the problem may be only within one print job or computer. Make sure the computer has the most current printer drivers, or use a generic printer driver. 4. Check for the latest firmware image version at the bottom of the page. If this firmware image is newer than the one installed on the device and the device can receive a firmware update, download the newer firmware upgrade. 5. Try printing a job from a different software program. If the job prints, go back to the first program and try printing a different file. If the message appears only with a certain software program or print job, contact the software vendor for assistance. 6. If the message persists, contact HP Support |
| Error code: | 50.1 |
| Display: | 50.1 FUSER ERROR |
| Description: | AC power is not being provided to the fuser assembly. AC voltage is necessary to generate heat in the fuser assembly. |
| Remedy: | 1. Verify that the fuser power cable at the back of the device is connected and the ECU is fully seated. 2. If the message persists, replace the fuser assembly. |
| Error code: | 50.2 |
| Display: | 50.<X> Fuser To continue turn off then on |
| Description: | A fuser error has occurred. fuser warm up service. |
| Remedy: | - Turn the product off, and then on. - Reseat the connection to the fuser and the DC controller. - Replace the fuser. - Replace the upper cable guide assembly. - Replace the low voltage power supply. - Replace the DC controller |
| Error code: | 50.3 |
| Display: | 50.<X> Fuser To continue turn off then on |
| Description: | A fuser error has occurred. high fuser temperature |
| Remedy: | - Turn the product off, and then on. - Reseat the connection to the fuser and the DC controller. - Replace the fuser. - Replace the upper cable guide assembly. - Replace the low voltage power supply. - Replace the DC controller |
| Error code: | 50.4 |
| Display: | 50.<X> Fuser To continue turn off then on |
| Description: | A fuser error has occurred.f aulty fuser. |
| Remedy: | - Turn the product off, and then on. - Reseat the connection to the fuser and the DC controller. - Replace the fuser. - Replace the upper cable guide assembly. - Replace the low voltage power supply. - Replace the DC controller |
| Error code: | 50.5 |
| Display: | 50.<X> Fuser To continue turn off then on |
| Description: | A fuser error has occurred. inconsistent fuser. |
| Remedy: | - Turn the product off, and then on. - Reseat the connection to the fuser and the DC controller. - Replace the fuser. - Replace the upper cable guide assembly. - Replace the low voltage power supply. - Replace the DC controller |
| Error code: | 50.7 |
| Display: | 50.X FUSER ERROR To continue turn off then on |
| Description: | A fuser error has occurred. fuser pressure release malfunction |
| Remedy: | 1. Turn the device off, and allow it to cool. 2. Verify that the correct model of fuser is installed. 3. Verify that the correct voltage fuser is installed. 4. Reinstall the fuser, and check the connection between the fuser and the high-voltage power supply. Replace the high-voltage power supply if the connector is damaged. 5. Replace the fuser. Replace the dc controller PCA. See DC controller PCA on page 357. 7. Replace the high-voltage power supply. |
| Error code: | 50.8 |
| Display: | 50.X FUSER ERROR To continue turn off then on |
| Description: | A fuser error has occurred. low fuser temperature |
| Remedy: | 1. Turn the device off, and allow it to cool. 2. Verify that the correct model of fuser is installed. 3. Verify that the correct voltage fuser is installed. 4. Reinstall the fuser, and check the connection between the fuser and the high-voltage power supply. Replace the high-voltage power supply if the connector is damaged. 5. Replace the fuser. Replace the dc controller PCA. See DC controller PCA on page 357. 7. Replace the high-voltage power supply. |
| Error code: | 50.9 |
| Display: | 50.X FUSER ERROR To continue turn off then on |
| Description: | A fuser error has occurred. high fuser temperature |
| Remedy: | 1. Turn the device off, and allow it to cool. 2. Verify that the correct model of fuser is installed. 3. Verify that the correct voltage fuser is installed. 4. Reinstall the fuser, and check the connection between the fuser and the high-voltage power supply. Replace the high-voltage power supply if the connector is damaged. 5. Replace the fuser. Replace the dc controller PCA. See DC controller PCA on page 357. 7. Replace the high-voltage power supply. |
| Error code: | 50.A |
| Display: | 50.WX.YZ Fuser error To continue |
| Description: | The fuser has experienced an error. W = fuser error code, X = fuser mode, Y = previous printer sleep state, Z = next printer sleep state Low fuser temperature 3 |
| Remedy: | 1. Remove and then reseat the fuser. Make sure there is no residual paper in the fuser. Make sure the device is not located in front of a vent or window where cool air may interfere with the ability of the fuser to heat up. 2. Check the product power source. Make sure the power source meets product requirements. Make sure this is the only device using the circuit. 3. Replace the fuser. 4. Check the connector (J704) between the fuser and the printer. If it is damaged, replace the fuser drive assembly or fuser. 5. If this product has been previously serviced, check the connector (J131) on the DC controller PCA and the connectors (J109 and J110) on the power line between the low-voltage power supply assembly and the fuser. |
| Error code: | 50.B |
| Display: | 50.WX.YZ Fuser error To continue |
| Description: | The fuser has experienced an error. W = fuser error code, X = fuser mode, Y = previous printer sleep state, Z = next printer sleep state High fuser temperature 3 |
| Remedy: | 1. Remove and then reseat the fuser. 2. Check the paper type setting using the product menus and in the printer driver. Making sure that they match and are correct for the type of media being used. 3. Replace the fuser. 4. Check the connector (J704) between the fuser and the printer. If it is damaged, replace the fuser drive assembly or fuser. 5. If this product has been previously serviced, check the connector (J131) on the DC controller PCA. |
| Error code: | 51.1Y |
| Display: | 51.1Y PRINTER ERROR |
| Description: | A laser error has occurred. Y 0 - Black 1 - Cyan 2 - Magenta 3 - Yellow |
| Remedy: | 1. Turn the printer off then on. 2. Reseat the connectors (J1002 - Y, J1003 - C, J1004 - M, J1005 - K) between the laser/scanner and DC controller PCB. 3. Upgrade formatter and DC Controller firmware. 4. Replace the defective laser/scanner assembly. Calibrate the printer after replacing the laser/ scanner. |
| Error code: | 51.2Y |
| Display: | 51.2Y PRINTER ERROR |
| Description: | A laser beam error has occurred. Y 0 - Black 1 - Cyan 2 - Magenta 3 - Yellow |
| Remedy: | 1. Turn the printer off then on. 2. Upgrade formatter and DC Controller firmware, which can be found in a single. 3. Reseat the connectors (J1002 - Y, J1003 - C, J1004 - M, J1005 - K) between the laser/scanner and DC controller PCB. 4. Replace the defective laser/scanner assembly. Calibrate the printer after replacing the laser/ scanner |
| Error code: | 52.00 |
| Display: | 52.00 ERROR |
| Description: | A scanner motor error has occurred. Scanner motor rotation is verified at the initialization of a print job. |
| Remedy: | 1. Verify that the scanner motor connector and the ribbon cable from the ECU are firmly seated on the laser/scanner assembly. 2. Verify that the scanner motor connector is firmly seated in connector J402 on the ECU. You might have to remove the main cooling fan to see this connection. 3. Verify that the ribbon cable installed in connector J403 on the ECU is fully seated You must remove the ECU in order to verify this connection. 4. If the message persists, replace the laser/scanner assembly. |
| Error code: | 52.10 |
| Display: | 52.XY ERROR To continue turn off then on |
| Description: | A temporary printing error has occurred. laser/scanner motor startup failure error |
| Remedy: | 1. Turn the device off, and then turn the device on. 2. Reseat the connectors between the laser/scanner and the dc controller PCA (J801 and J321). 3. Replace the laser/scanner assembly. 4. Replace the dc controller PCA. |
| Error code: | 52.20 |
| Display: | 52.XY ERROR To continue turn off then on |
| Description: | A temporary printing error has occurred. laser/scanner motor rotation speed error |
| Remedy: | 1. Turn the device off, and then turn the device on. 2. Reseat the connectors between the laser/scanner and the dc controller PCA (J801 and J321). 3. Replace the laser/scanner assembly. 4. Replace the dc controller PCA. |
| Error code: | 53.10.0X |
| Display: | 53.10.0X Unsupported DIMM |
| Description: | An unsupported DIMM is installed. |
| Remedy: | Turn the product off, and then replace the DIMM that caused the error. |
| Error code: | 54.01 |
| Display: | 54.<XX> Error |
| Description: | A sensor error has occurred. Temperature |
| Remedy: | Turn the MFP off, and then turn the MFP on. If the error reappears, record the message and contact support. |
| Error code: | 54.15 |
| Display: | 54.XX Error |
| Description: | The product has experienced an error with one of the print cartridge sensors. yellow |
| Causes: | Yellow toner level sensor error |
| Remedy: | 1. Open the door to the cartridge tray and slide out the cartridge tray. 2. Inspect the white mechanism on the relevant cartridge. It is located on the right side of the cartridge. 3. Push the mechanism in and out slowly. A black flag will raise up as you push it. If it does not move smoothly, push repeatedly to try to clear any potential obstruction. 4. Push in the cartridge tray and close the door. |
| Error code: | 54.16 |
| Display: | 54.XX Error |
| Description: | The product has experienced an error with one of the print cartridge sensors. magenta |
| Causes: | Magenta toner level sensor error |
| Remedy: | 1. Open the door to the cartridge tray and slide out the cartridge tray. 2. Inspect the white mechanism on the relevant cartridge. It is located on the right side of the cartridge. 3. Push the mechanism in and out slowly. A black flag will raise up as you push it. If it does not move smoothly, push repeatedly to try to clear any potential obstruction. 4. Push in the cartridge tray and close the door. |
| Error code: | 54.17 |
| Display: | 54.XX Error |
| Description: | The product has experienced an error with one of the print cartridge sensors. cyan |
| Causes: | Cyan toner level sensor error |
| Remedy: | 1. Open the door to the cartridge tray and slide out the cartridge tray. 2. Inspect the white mechanism on the relevant cartridge. It is located on the right side of the cartridge. 3. Push the mechanism in and out slowly. A black flag will raise up as you push it. If it does not move smoothly, push repeatedly to try to clear any potential obstruction. 4. Push in the cartridge tray and close the door. |
| Error code: | 54.18 |
| Display: | 54.XX Error |
| Description: | The product has experienced an error with one of the print cartridge sensors. black |
| Causes: | Black toner level sensor error |
| Remedy: | 1. Open the door to the cartridge tray and slide out the cartridge tray. 2. Inspect the white mechanism on the relevant cartridge. It is located on the right side of the cartridge. 3. Push the mechanism in and out slowly. A black flag will raise up as you push it. If it does not move smoothly, push repeatedly to try to clear any potential obstruction. 4. Push in the cartridge tray and close the door. |
| Error code: | 55.00.YY |
| Display: | 55.00.YY DC controller error To continue turn off then on |
| Description: | DC controller PCA error - 55.00.01 (event code) DC controller memory error - 55.00.03 (event code DC controller no engine response - 55.00.04 (event code DC controller communications timeout |
| Remedy: | Turn the product off, and then on. If the error persists, replace the DC controller PCA. |
| Error code: | 55.01.YY |
| Display: | 55.XX.YY DC CONTROLLER ERROR - To Continue Turn Off Then On |
| Description: | The print engine is not communicating with the formatter. Incoming parity error |
| Remedy: | Turn the MFP off, and then turn the MFP on. |
| Error code: | 55.02.YY |
| Display: | 55.XX.YY DC CONTROLLER ERROR - To Continue Turn Off Then On |
| Description: | The print engine is not communicating with the formatter. Outgoing parity error |
| Remedy: | Turn the MFP off, and then turn the MFP on. |
| Error code: | 55.03.YY |
| Display: | 55.03.YY No Engine Responsesupply unit. |
| Description: | DC controller no response error. |
| Remedy: | 1. Turn the product off and then on. 2. Perform an engine test. 3. Verify the connectors on the DC controller. 4. Replace the DC controller. |
| Error code: | 55.04.YY |
| Display: | 55.XX.YY DC CONTROLLER ERROR - To Continue Turn Off Then On |
| Description: | The print engine is not communicating with the formatter. Communications timeout |
| Remedy: | Turn the MFP off, and then turn the MFP on. |
| Error code: | 55.05 |
| Display: | 55.05 Engine Firmware RFU Error To continue turn off then on |
| Description: | An issue caused the firmware upgrade to fail. |
| Remedy: | - Turn the product off, and then on. - Restart the firmware upgrade. - If the problem continues, try a different firmware file. |
| Error code: | 56.01 |
| Display: | 56.XX ERROR To continue turn off then on |
| Description: | A temporary printing error has occurred. unknown input device, selected media input unavailable |
| Remedy: | 1. Turn the device off, and then turn the device on. 2. For 56.01 errors, check the connections to the input device (optional 1 x 500- or 3 x 500-sheet feeder.) For 56.02 errors, check the connections to the optional stapler stacker. 3. Remove all non-HP paper-handling devices. 4. Perform a RFU. |
| Error code: | 56.02 |
| Display: | 56.XX ERROR To continue turn off then on |
| Description: | A temporary printing error has occurred. unknown output device, selected media output bin unavailable |
| Remedy: | 1. Turn the device off, and then turn the device on. 2. For 56.01 errors, check the connections to the input device (optional 1 x 500- or 3 x 500-sheet feeder.) For 56.02 errors, check the connections to the optional stapler stacker. 3. Remove all non-HP paper-handling devices. 4. Perform a RFU. |
| Error code: | 57.01 |
| Display: | 57.01 |
| Description: | Fan 1 error. The product has experienced an error with its internal fan. |
| Causes: | Fan 1 error |
| Remedy: | 1. Reset the printer:a. Turn off the power by using the power switch, and then wait at least 30 seconds.b. Turn on the power and wait for the product to initialize.2. If you are using a surge protector:a. Power off the printer.b. Remove the surge protector.c. Plug the product directly into the wall socket and turn the product power on.3. If the error persists, replace the internal cooling fan (HP Part #: RK2-8068-000CN).4. If the error persists, replace the product. |
| Error code: | 57.03 |
| Display: | 57.03 ERROR |
| Description: | Fan FN102 has experienced an error. |
| Remedy: | 1. Inspect fan FN102 to determine if its rotational movement is being obstructed. 2. Verify that the fan connection at connector J75 on the DC controller PCA is securely seated. 3. If the error persists, replace the fan. |
| Error code: | 57.04 |
| Display: | 57.04 ERROR |
| Description: | Fan FN101 has experienced an error. |
| Remedy: | 1. Inspect fan FN101 to determine if its rotational movement is being obstructed. 2. Verify that the fan connection at connector J64 on the power supply PCA is securely seated. 3. If the error persists, replace the fan. |
| Error code: | 57.05 |
| Display: | 57.05 ERROR |
| Description: | The duplexer fan has experienced an error. |
| Remedy: | 1. Inspect the fan to determine if its rotational movement is being obstructed. 2. If the error persists, replace the duplexer. |
| Error code: | 57.06 |
| Display: | 57.<XX> Error To continue turn off then on |
| Description: | A product error occurred. face-down bin error. |
| Remedy: | - Turn the product off and turn it on. - Reseat connections to the DC controller and to the specified fan. - Replace the specified fan. - Replace the DC controller. |
| Error code: | 57.07 |
| Display: | 57.07 ERROR |
| Description: | Fan FN301 has experienced an error. |
| Remedy: | 1. Inspect fan FN301 to determine if its rotational movement is being obstructed. 2. Verify that the fan connection at connector J65 on the power supply PCA is securely seated. 3. If the error persists, replace the fan. |
| Error code: | 57.08 |
| Display: | 57.<XX> Error To continue turn off then on |
| Description: | A product error occurred. duplexer fan error. |
| Remedy: | - Turn the product off and turn it on. - Reseat connections to the DC controller and to the specified fan. - Replace the specified fan. - Replace the DC controller. |
| Error code: | 57.09 |
| Display: | 57.09 ERROR |
| Description: | The IPTU feed-unit cooling fan (FM8) has experienced an error. |
| Remedy: | 1. Reconnect the connectors of the IPTU media-feed-unit cooling fan (J7008), IPTU driver PCA (J7001), and the DC controller PCA (J130). 2. Reinstall the IPTU. 3. Measure the voltage between the connector J7008-1 and J7008-3 on the IPTU driver PCA right after the product is turned on. If the voltage changes from 0V to approximately 24V, replace the IPTU media-feed-unit cooling fan. |
| Error code: | 59.30 |
| Display: | 59.<XY> Printer Error To continue turn off then on |
| Description: | A product error occurred. fuser motor startup error. |
| Causes: | Fuser motor startup error |
| Remedy: | - Turn the product off, and then on. - Check connections from the specified motor to the DC controller. - Reseat or reconnect the specified motor. - Replace the print cartridge if the problem is with its motors. - Run a service test. - Replace the specified motor. - Replace the fuser. - Replace the DC controller |
| Error code: | 59.40 |
| Display: | 59.<XY> Printer Error To continue turn off then on |
| Description: | A product error occurred. fuser motor rotation error. |
| Causes: | Fuser motor rotation error |
| Remedy: | - Turn the product off, and then on. - Check connections from the specified motor to the DC controller. - Reseat or reconnect the specified motor. - Replace the print cartridge if the problem is with its motors. - Run a service test. - Replace the specified motor. - Replace the fuser. - Replace the DC controller |
| Error code: | 59.50 |
| Display: | 59.50 ERROR |
| Description: | A main motor (M1) error has occurred. Motor operation is verified during device power-up. |
| Remedy: | 1. Turn the device off and then on. 2. Verify that nothing is hindering the main motor. If necessary, remove all paper trays and the print cartridge, and then turn on the device and listen for motor operation. 3. Verify that the main motor is connected to connector J407 on the ECU. You might have to remove the main cooling fan to see this connection. 4. If the message persists, replace the motor. |
| Error code: | 59.51 |
| Display: | 59.X Error |
| Description: | Image drum motor startup or rotation error-cyan, magenta, or yellow. - Image drum motor startup error-cyan |
| Remedy: | 1. Reconnect the connector (J515) on the drum motor and the connector (J81) on the DC controller PCA. 2. Run the drum motor drive test in the actuator drive mode to verify that the drum motor is functioning correctly. If it is not, replace the drum motor unit. |
| Error code: | 59.52 |
| Display: | 59.X Error |
| Description: | Image drum motor startup or rotation error-cyan, magenta, or yellow. - Image drum motor startup error-magenta |
| Remedy: | 1. Reconnect the connector (J515) on the drum motor and the connector (J81) on the DC controller PCA. 2. Run the drum motor drive test in the actuator drive mode to verify that the drum motor is functioning correctly. If it is not, replace the drum motor unit. |
| Error code: | 59.53 |
| Display: | 59.X Error |
| Description: | Image drum motor startup or rotation error-cyan, magenta, or yellow. - Image drum motor startup error-yellow |
| Remedy: | 1. Reconnect the connector (J515) on the drum motor and the connector (J81) on the DC controller PCA. 2. Run the drum motor drive test in the actuator drive mode to verify that the drum motor is functioning correctly. If it is not, replace the drum motor unit. |
| Error code: | 59.60 |
| Display: | 59.X Error |
| Description: | Image drum motor startup or rotation error-black. - Image drum motor rotation error-black |
| Remedy: | 1. Reconnect the connector (J517) on the ITB motor and the connector (J81) on the DC controller PCA. 2. Run the drum motor drive test in the actuator drive mode to verify that the ITB motor is functioning correctly. If it is not, replace the ITB motor unit. |
| Error code: | 59.61 |
| Display: | 59.X Error |
| Description: | Image drum motor startup or rotation error-cyan, magenta, or yellow. - Image drum motor rotation error-cyan |
| Remedy: | 1. Reconnect the connector (J515) on the drum motor and the connector (J81) on the DC controller PCA. 2. Run the drum motor drive test in the actuator drive mode to verify that the drum motor is functioning correctly. If it is not, replace the drum motor unit. |
| Error code: | 59.62 |
| Display: | 59.X Error |
| Description: | Image drum motor startup or rotation error-cyan, magenta, or yellow. - Image drum motor rotation error-magenta |
| Remedy: | 1. Reconnect the connector (J515) on the drum motor and the connector (J81) on the DC controller PCA. 2. Run the drum motor drive test in the actuator drive mode to verify that the drum motor is functioning correctly. If it is not, replace the drum motor unit. |
| Error code: | 59.63 |
| Display: | 59.X Error |
| Description: | Image drum motor startup or rotation error-cyan, magenta, or yellow. - Image drum motor rotation error-yellow |
| Remedy: | 1. Reconnect the connector (J515) on the drum motor and the connector (J81) on the DC controller PCA. 2. Run the drum motor drive test in the actuator drive mode to verify that the drum motor is functioning correctly. If it is not, replace the drum motor unit. |
| Error code: | 59.90 |
| Display: | 59.XX Error, Turn off then on |
| Description: | The product has experienced an error with one of the internal motors. |
| Causes: | ITB motor start error |
| Remedy: | 1. Reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize. 2. If you are using a surge protector: a. Power off the printer. b. Remove the surge protector. c. Plug the product directly into the wall socket and turn the product power on. 3. If the error persists, replace the appropriate motor: Error Code Motor Description HP Part # 59.30, 59.40 Fuser Motor Assembly RM2–7348–000CN 59.70, 59.71, 59.72, 59.73, 59.80, 59.80, 59.82, 59.83 59.C0 Developing Motor Assembly RM2–7344–000CN 59.90, 59.A0, 59.FO Drum Motor Assembly RM2–7342–000CN |
| Error code: | 59.A0 |
| Display: | 59.X Error |
| Description: | ITB motor start error or rotation error. - ITB motor rotation error |
| Causes: | ITB motor rotation error |
| Remedy: | 1. Reconnect the connector (J517) on the ITB motor and the connector (J81) on the DC controller PCA. 2. Run the ITB motor drive test in the actuator drive mode to verify that the ITB motor is functioning correctly. If it is not functioning correctly, replace the ITB motor unit. |
| Error code: | 59.C0 |
| Display: | 59.C0 Error |
| Description: | Developer motor rotation error. |
| Causes: | Developer motor rotation error |
| Remedy: | 1. Reconnect the connector (J518) on the developing disengagement motor, the connector (J1005) on the driver PCA and the connector (J91) on the DC controller PCA. 2. Run the sensor test in the sensor monitor mode to verify that the developing disengagement sensor is functioning correctly. If it is not, replace the developing disengagement sensor unit. 3. Run the developing unit engagement and disengagement drive test in the actuator drive mode to verify that the disengagement mechanism is functioning correctly. If it is not functioning correctly, replace the developing disengagement motor. |
| Error code: | 59.F0 |
| Display: | 59.F0 Error |
| Description: | Transfer alienation failure. |
| Causes: | Transfer alienation failure |
| Remedy: | 1. Check if the ITB unit is installed. 2. Reconnect the connector (J181) on the DC controller PCA. 3. Run the switch test in the sensor monitor mode to verify that the primary transfer roller disengagement switch is functioning correctly. If it is not functioning correctly, replace the primary transfer roller disengagement switch unit. 4. Run the primary transfer roller engagement and disengagement drive test in the actuator drive mode to verify that the primary transfer roller disengagement mechanism is functioning correctly. If it is not functioning correctly, replace the fuser drive unit |
| Error code: | 59.XY |
| Display: | 59.XY ERROR |
| Description: | A temporary printing error occurred. |
| Remedy: | 1. Inspect the DC controller PCA and verify that the following connectors are firmly seated: • Drum motor (M102) to connector J87 • Feed motor (M101) to connector J91 • Fusing motor (M299) to connector J89 NOTE: There is a cable between the drum motor and the DC controller. Both ends of the cable need to be firmly seated. 2. If the error persists, from the DIAGNOSTICS menu, run the component tests for each motor to verify that they are operating. If any of the motors is not operating, replace the motor. |
| Error code: | 60.02 |
| Display: | 60.02 ERROR |
| Description: | Tray 2 is not lifting correctly. |
| Remedy: | 1. Reconnect connector J115 on the DC controller PCA and the intermediate connector J58. 2. Run the sensor test in sensor monitor mode to verify that the cassette media stack surface sensor is functioning properly. If it is not, replace the pickup assembly. 3. Reconnect connector J56 of the lifter motor. Also check J107 on the DC controller PCA. 4. If the message persists, replace the lifter drive assembly. |
| Error code: | 60.03 |
| Display: | 60.03 ERROR |
| Description: | Tray 3 is not lifting correctly. |
| Remedy: | 1. Reconnect connector J408 on the paper deck controller PCA and the intermediate connector J11. 2. Run the sensor test in sensor monitor mode to verify that the cassette media stack surface sensor is functioning properly. If it is not, replace the pickup assembly. 3. Reconnect connector J15 of the lifter motor. Also check J407 on the paper deck controller PCA. 4. If the message persists, replace the lifter drive assembly. |
| Error code: | 60.04 |
| Display: | 60.04 ERROR |
| Description: | Tray 4 is not lifting correctly. |
| Remedy: | 1. Reconnect connector J406 on the paper deck controller PCA and the intermediate connector J21. 2. Run the sensor test in sensor monitor mode to verify that the cassette media stack surface sensor is functioning properly. If it is not, replace the pickup assembly. 3. Reconnect connector J24 of the lifter motor. Also check J405 on the paper deck controller PCA. 4. If the message persists, replace the lifter drive assembly. |
| Error code: | 60.05 |
| Display: | 60.05 ERROR |
| Description: | Tray 5 is not lifting correctly. |
| Remedy: | 1. Reconnect the connector J403 on the paper deck controller PCA and the intermediate connector J31. 2. Run the sensor test in the sensor monitor mode to verify that the PD cassette media stack surface sensor is functioning properly. If it is not, replace the middle pickup assembly. 3. Reconnect the connector J34 of the lifter motor and the connector. Also check J402 on the paper deck controller PCA. 4. If the message persists, replace the lifter drive assembly. |
| Error code: | 60.XX |
| Display: | 60.XX ERROR |
| Description: | An error has occurred while the product was attempting to lift the tray designated by XX |
| Remedy: | 1. Open the tray, and then remove the paper. 2. Open the guides and look for any torn pieces of paper or foreign objects inside the tray. 3. Replace the paper, and then close the tray. 4. Turn the product off and then on. 5. Remove most of the paper from the tray except for a few sheets, and insert the tray into the product. Listen for the sound of the lift motor lifting the paper stack. Also, observe if the paper level indicator moves at the front of the tray. 6. Tray 2 only: If the paper stack in the tray is not being lifted, verify that the lift motor connector is firmly seated in connector J73 on the DC controller PCA. 7. If the error persists, replace the lift motor. |
| Error code: | 65.12.99 |
| Display: | 65.12.99 - Output Accessory Disconnected |
| Description: | An external paper handling accessory connection was interrupted. |
| Remedy: | - Turn the product off. - Make sure that the external paper handling accessory is clear of all packing material and other obstructions. - Check the external paper handling accessory connection, ensuring it is properly seated. If the accessory uses cables, disconnect and reconnect them. - Turn the product on. |
| Error code: | 66.00.15 |
| Display: | 66.00.15 - External device failure To continue turn off then on |
| Description: | This error occurs under the following conditions: - An external device was disconnected and a different external device (different model or same model with different firmware) was reconnected. - The external device begins to restart while the product is already running. This can happen due to interruptions with the power on signal. - An upgrade to the external device is not completed within a specified time. This can cause the PHC to crash, requiring the upgrade to be restarted. |
| Remedy: | - Make sure that the stacker bin area is clear of all packing material and other obstructions. - Turn the product off, and then on. - Check the external paper handling accessory connection to see that it is properly seated. If the accessory uses cables, disconnect them, and reconnect them. |
| Error code: | 66.12.01 |
| Display: | 66.XY.ZZ OUTPUT DEVICE FAILURE |
| Description: | An error occurred in an external paperhandling accessory. Output-lift roller or paddle-motor error |
| Remedy: | 1. Turn the MFP power off. 2. Check that the accessory is properly seated on and connected to the MFP, without any gaps between the MFP and the accessory. If the accessory uses cables, disconnect and reconnect them. 3. Turn the MFP power on. 4. If this message persists, replace the output device. |
| Error code: | 66.12.02 |
| Display: | 66.XY.ZZ OUTPUT DEVICE FAILURE |
| Description: | An error occurred in an external paperhandling accessory. Jogger-motor error |
| Remedy: | 1. Turn the MFP power off. 2. Check that the accessory is properly seated on and connected to the MFP, without any gaps between the MFP and the accessory. If the accessory uses cables, disconnect and reconnect them. 3. Turn the MFP power on. 4. If this message persists, replace the output device. |
| Error code: | 66.12.03 |
| Display: | 66.XY.ZZ OUTPUT DEVICE FAILURE |
| Description: | An error occurred in an external paperhandling accessory. Stapler motor error |
| Remedy: | 1. Turn the MFP power off. 2. Check that the accessory is properly seated on and connected to the MFP, without any gaps between the MFP and the accessory. If the accessory uses cables, disconnect and reconnect them. 3. Turn the MFP power on. 4. If this message persists, replace the output device. |
| Error code: | 66.12.11 |
| Display: | 66.12.<ZZ> Output accessory failure |
| Description: | This error is caused by failures in the output accessories. stapler carriage motor failure in the multi functional finisher. |
| Remedy: | - Follow the instructions in online help. - Turn the product off and turn it on. |
| Error code: | 66.12.12 |
| Display: | 66.12.12 |
| Description: | Finisher error - shutter movement malfunction Normal operation: When the shutter clutch (CL31) and stack ejection lower roller clutch (CL32) are on, the shutter moves up (closed) when the stack ejection motor (M32) turns forward and moves down (open, delivery enabled) when the motor turns backwards. Error occurs when the shutter home position sensor (PI45) indicates no change when the stack ejection motor (M32) is activated for 3 seconds, indicating that the shutter is not moving. |
| Remedy: | Control panel diagnostics: none 1. Inspect the shutter for damage. If the shutter cannot freely move, replace the shutter assembly. 2. Remove the lower guide (grate-shaped) and check sensor PI45 for damage. Make sure that the sensor is securely fastened to the chassis. 3. Check for proper alignment of the shutter mounted on the back of the grate-shaped lower guide and the lift mechanism on the finisher chassis. 4. Verify that connector J721 on the stacker controller PCA is fully seated and not damaged. 5. Check CL31 during operation, and verify that it is correctly functioning by activating prior to the error. Replace CL31 if necessary. 6. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. |
| Error code: | 66.12.13 |
| Display: | 66.12.13 |
| Description: | Finisher error - stack trailing-edge motor (M39) In order to improve stacking performance when ejecting copies, a trailing edge assist guide is used in addition to the stack ejection roller to support the rear end of the stack during stack ejection. Error occurs when the stacker trailing-edge guide does not leave its home position (PI39) after the stack trailing-edge motor (M39) has been turned on for 3 seconds. |
| Remedy: | Control panel diagnostics: M39 process motor (stack trailing-edge assist motor) Test the swing motor M39 by using the finisher component test from the controlpanel display. • If the trailing-edge assist guide does not move, perform the following steps: • Verify that connector J722 on the stacker controller PCA is fully seated and not damaged. Also check the wiring at motor M39 and sensor PI39. • Replace the operation-tray assembly (processing tray). • Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. • If the trailing-edge assist guide does move, perform the following steps: • Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. • Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. • Verify that connector J722 on the stacker controller PCA is fully seated and not damaged. Also check the wiring at sensor PI39. • Replace the operation-tray assembly (processing tray). |
| Error code: | 66.12.14 |
| Display: | 66.12.14 |
| Description: | Finisher stapling and offsetting front-aligningplate motor failure In order to neatly align the paper stack for either stapling or offsetting to take place, the front and rear-aligning plates move to align each sheet when it enters the processing tray. The error occurs when the aligning plate either does not leave or when it does not return to the aligning-plate front-homeposition sensor (PI36) when the frontaligning- plate motor (M33) has been driven for 4 seconds. |
| Remedy: | Control panel diagnostics: none 1. Verify that Offsetting is turned On in the Device Behavior menu. 2. Verify that connector J722 on the stacker controller PCA is fully seated and not damaged. Also check the wiring at sensor PI39 and motor M33. 3. Replace the operation-tray assembly (processing tray). 4. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. |
| Error code: | 66.12.15 |
| Display: | 66.12.15 |
| Description: | Finisher stapling or offsetting rear aligning plate motor failure (M34) In order to neatly align the paper stack for either stapling or offsetting to take place, the front and rear aligning plates move to align each sheet when it enters the processing tray. The error occurs when the aligning plate either does not leave or when it does not return to the aligning-plate-rear-homeposition sensor (PI37) when the alignment plate rear motor (M34) has been driven for 4 seconds. |
| Remedy: | Control panel diagnostics: none 1. Verify that Offsetting is turned On in the Device Behavior menu. 2. Verify that connector J722 on the stacker controller PCA is fully seated and not damaged. Also check the wiring at sensor PI37 and motor M34. 3. Replace the operation-tray assembly (processing tray). 4. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. |
| Error code: | 66.12.16 |
| Display: | 66.12.16 |
| Description: | Finisher error - speed change motor (M40) The speed change motor M40 and sensor PI49 associated with this error have been removed from the output device prior to introduction to the field. This error message should never be seen in the field. |
| Remedy: | If error message appears, contact HP Support and report the error. HP Support: Report error to Technical Marketing. |
| Error code: | 66.12.21 |
| Display: | 66.12.<ZZ> Output accessory failure |
| Description: | This error is caused by failures in the output accessories. bearing bracket failure (damage) in the stapler stacker. |
| Remedy: | - Follow the instructions in online help. - Turn the product off and turn it on. |
| Error code: | 66.12.22 |
| Display: | 66.12.22 |
| Description: | Finisher upper stapler shift motor failure (M35) Error occurs when the stapler does not leave the stapler-shift home-position sensor (PI40) after the stapler-shift motor (M35) has driven for 5 seconds. Also occurs when the stapler fails to return to the stapler-shift home-position sensor (PI40) after the stapler-shift motor (M35) has been driven for 20 seconds. |
| Remedy: | Control panel diagnostics: M35 staple motor (stapler-shift motor) and PI140 stapler home sensor (stapler home-position sensor) 1. Test the upper-stapler-shift motor M35 by using the finisher component test from the control-panel display. • If the stapler unit moves properly, proceed to the next step in this section. • If the stapler unit does not move properly or moves erratically, perform the following steps:• Check the flat-flexible cable (FFC) for damage (dents, folds, and/or tears). Replace the FFC if necessary.• Check the FFC connectors and cable mounting areas.• If the error persists, replace the stapler assembly 2. Test the stapler-shift home position sensor PI40 by using the finisher component test from the control-panel display. • If the sensor does not change state when the stapler unit is moved from the home position, perform the following steps: • Make sure that the sensor is securely fastened to the chassis. • Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. • Verify that connector J1040 on the stacker controller PCA is fully seated and not damaged. Check the wiring at the sensor. • If the error persists, replace the stapler assembly. NOTE: The stapler assembly includes the stapler-shift home position sensor PI40, stapler unit, shift-position-plate assembly, and the flat-flexible cable (FFC). |
| Error code: | 66.12.23 |
| Display: | 66.12.23 |
| Description: | Finisher upper-stapler failure Occurs when stapler alignment interference sensor (PI46) is activated, signaling that the stapler unit is not in its proper position for stapling to occur. This is to prevent damage to stapler from occurring when stapler is positioned over one of the three stoppers when the signal to staple has been sent. |
| Remedy: | Control-panel diagnostics: none 1. If the stapler unit does not move properly or moves erratically, check the flat-flexible cable (FFC) for damage (dents, folds, and/or tears). Replace the FFC if necessary. 2. If the stacker controller PCA was recently replaced, use the steps in this manual to adjust the staple alignment and staple position. 3. If the stapler is not positioned over a stopper when this error occurs, perform the following steps. • Make sure that the stapler unit is correctly mounted and securely fastened to the base. • Make sure that the sensor is not obstructed or damaged. Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. • If the error persists, replace the stapler subassembly. NOTE: The stapler subassembly includes the stapler unit and base |
| Error code: | 66.12.31 |
| Display: | 66.12.<ZZ> Output accessory failure |
| Description: | This error is caused by failures in the output accessories. home position timeout failure in the multi functional finisher. |
| Remedy: | - Follow the instructions in online help. - Turn the product off and turn it on. |
| Error code: | 66.12.32 |
| Display: | 66.12.<ZZ> Output accessory failure |
| Description: | This error is caused by failures in the output accessories. home position timeout failure in the aligning paddles on the multi functional finisher. |
| Remedy: | - Follow the instructions in online help. - Turn the product off and turn it on. |
| Error code: | 66.12.34 |
| Display: | 66.12.<ZZ> Output accessory failure |
| Description: | This error is caused by failures in the output accessories. front paper alignment motor failure (motor 3) in the multi functional finisher. |
| Remedy: | - Follow the instructions in online help. - Turn the product off and turn it on. |
| Error code: | 66.12.41 |
| Display: | 66.12.<ZZ> Output accessory failure |
| Description: | This error is caused by failures in the output accessories. stapling folder motor failure (motor 7) in the multi functional finisher. |
| Remedy: | - Follow the instructions in online help. - Turn the product off and turn it on. |
| Error code: | 66.12.42 |
| Display: | 66.12.42 |
| Description: | Finisher error: folding-guide motor (M3) The guide motor (M3), located in the bookletmaking area of the finisher, controls the position of the guide plate. The guide plate is positioned in front of the folding rollers as the paper stack is being stapled, allowing the bottom edge of the paper to smoothly pass by the folding rollers. When the stacked paper is lowered to the folding position, the guide motor (M3) lowers the guide plate out of the way to allow the paper stack to be pushed into the folding rollers. Error occurs when The guide-home-position sensor (PI13) does not turn on when the guide motor (M3) has been driven for 700 pulses. Also occurs when the guide-home-position sensor (PI13) does not turn off when the guide motor (M3) has been driven for 50 pulses. |
| Remedy: | Control panel diagnostics: M3 guide motor 1. Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. 2. Make sure that the sensor is securely fastened to the plate. 3. Check the wiring at the sensor. 4. Check sensor PI13 for damage. 5. Check the guide, gears, and gear tracks on the front and rear frame for damage. Replace components as necessary. 6. If the error persists, replace the guide motor M3 and the guide home position sensor PI13 together. |
| Error code: | 66.12.43 |
| Display: | 66.12.43 |
| Description: | Finisher error: paper-fold motor (M2) M2: paper-fold motor, located in the booklet making area of the finisher, drives the rotation of the folding rollers to create the desired fold in the paper. The error occurs when the number of pulses by the paper-fold-motor clock sensor (PI4) is less than expected standard value. Also occurs when the status of the paper-fold home-position sensor (PI21) does not change when the paper-fold motor (M2) has been driven for 3 seconds. |
| Remedy: | Control panel diagnostics: M2 folding motor (paper-fold motor) 1. Check the area around the folding rollers for a jam. 2. Test the paper-fold motor M2 by using the finisher component test from the control-panel display. • If the folding rollers rotate properly, perform the following steps: • Check sensor PI4 and sensor PI21 for damage. • Verify that the sensor flags are not damaged, move freely, and are correctly aligned with the PI48 and PI21 sensor bodies. • Make sure that the sensors are securely fastened to the chassis. • Carefully clean each sensor body with a clean, lint-free cloth, or gently blow clean air across each sensor to remove dust and debris. • Verify that connector J3 on the saddle-stitcher controller PCA is fully seated and not damaged. Check the wiring at the PI4 sensor. • Verify that connector J18 on the saddle-stitcher controller PCA is fully seated and not damaged. Check the wiring at the PI21 sensor. • If the error persists, replace sensor PI4 or PI21. • Only if the error persists and the previous steps fail to correct the problem, replace the saddle-stitcher controller PCA. • If the folding rollers do not rotate properly, perform the following steps: • Check the folding-roller gears and connecting gears between the paper-fold motor M2 and the folding rollers for damage. Replace components as necessary. • Check the folding rollers for wear and damage. Replace components as necessary. • Replace the motor-mount assembly. NOTE: The motor-mount assembly includes the paperfold motor M2 and the paperfold motor-clock sensor PI4. • Only if the error persists and the previous steps fail to correct the problem, replace the saddle-stitcher controller PCA. |
| Error code: | 66.12.44 |
| Display: | 66.12.44 |
| Description: | Finisher - folding-paper-alignment motor (M5) M5: The alignment motor, located in the booklet making area of the finisher, drives the two alignment plates that adjust the side edges of the stacked paper so that the paper in the stack is perfectly aligned with one another. Error occurs when the aligning-plate homeposition sensor (PI5) does not turn on when the aligning plate motor (M5) has been driven for 500 pulses. Also occurs when the aligning-plate homeposition sensor (PI5) does not turn off when the aligning-plate motor (M5) has been driven for 50 pulses. |
| Remedy: | Control panel diagnostics: none Observe the alignment plates during a booklet-maker stacking operation. • If the alignment plates move during the operation, perform the following steps: • Check sensor PI5 for damage. • Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. • Make sure that the sensor is securely fastened to the chassis. • Carefully clean the sensor body by gently blowing clean air across the sensors to remove dust and debris. • If the alignment plates or the alignment-plates drive gear has been removed or replaced, make sure that the plates are correctly aligned with each other on the drive gear. • If the alignment plates do not move during the operation, perform the following steps: • Remove motor M5 and check the gears between the motor and alignment plates for damage. Replace components as necessary. • Verify that connector J7 on the saddle-stitcher controller PCA is fully seated and not damaged. Check the wiring at the M5 motor. • Replace the alignment motor M5. • Only if the error persists and the previous steps fail to correct the problem, replace the saddlestitcher controller PCA. |
| Error code: | 66.12.45 |
| Display: | 66.12.45 |
| Description: | Finisher: paper-pushing-plate motor (M8) Error occurs when the paper-pushing-plate home-position sensor (PI14) does not turn on when the paper-pushing-plate motor (M8) has been driven for 0.3 seconds. Also occurs when the paper-pushing-plate home-position sensor (PI14) does not turn off when the paper-pushing-plate motor (M8) has been driven for 80 ms. Also occurs when the paper pushing-plate leading-edge-position sensor (PI15) does not turn off when the paper-pushing-plate motor (M8) has been driven for 80 ms. Also occurs when the number of pulses detected by the paper-pushing-plate motor clock sensor (PI1) is less than expected standard value. Also occurs when the paper pushing-plateleading- edge-position sensor (PI15) does not turn on when the paper-pushing-plate motor (M8) has been driven for 0.3 seconds. |
| Remedy: | Control panel diagnostics: none 1. Open the front-finishing door, and activate the front-door switch (MSW31) and front-door sensor (PI32) so that the finisher will operate with the front door open. Turn the engine and finisher power off to clear the error, and then turn the power on. WARNING! Operating the finisher with the front door open exposes moving parts that can cause serious injury. Be very careful operating the finisher with the front door open. 2. Use the control-panel menus to begin a booklet making operation. Observe the paper-pushing plate motor M8 (located in the lower-right front corner of the finisher), associated gears, and the paper-pushing plate for proper motion. • If motor M8 does not rotate, replace the motor-mount assembly. NOTE: The motor-mount assembly includes the paperpushing plate motor M8. • If motor M8 does rotate but the paper-pushing plate does not move or moves erratically, check the drive gears and paper-pushing plate for wear or damage. Replace components as necessary. • If motor M8 does rotate and the paper-pushing plate moves properly, the plate movement sensors might have failed. • Inspect the paper-pushing plate home position sensor PI14, pushing-plate leadingedge position sensor PI15, and paper-pushing motorclock sensor PI1. Make sure that the sensors are securely fastened to the chassis. Check sensor PI4, sensor PI15, and sensor PI1 for damage. • Verify that connectors J6, J9, and J23 on the saddlestitcher controller PCA are fully seated and not damaged. Check the wiring at the sensors. • Only if the error persists and the previous steps fail to correct the problem, replace the saddle-stitcher controller PCA. |
| Error code: | 66.12.46 |
| Display: | 66.12.46 |
| Description: | Finisher - Communication Lost with Stitcher Controller PCA This error occurs when communication between the stacker-controller board and the saddle-stitchercontroller board is lost or interrupted. |
| Remedy: | 1. Make sure that the finisher is grounded correctly. • Make sure that the finisher is latched and locked to the engine by tightening the thumbscrew inside the front door. • Make sure that the grounding-frame assembly (the bar with the wheel located between the engine and the finisher) is in the down position with the wheel touching the floor and that the grounding plate is not damaged. NOTE: The grounding-frame assembly is in the up position when the finisher is shipped. It must be lowered when the finisher is installed. 2. Make sure that the connector J730 on the stacker controller PCA and the wiring between connector J22 on the saddle-stitcher controller PCA are fully seated and not damaged. 3. Replace the saddle-stitcher controller PCA. 4. If the error persists, replace the stacker controller PCA. |
| Error code: | 66.12.47 |
| Display: | 66.12.47 |
| Description: | Finisher error: micro switches and doors There are three switches in the bookletmaker finisher: SW1 (saddle-guide switch also known as the inlet-door switch), SW3 the booklet-ejection door switch, and MS31 the front-door switch. The stapler/stacker finisher only has one switch, MS31 for the front door of the finisher. All three switches detect if the associated door or guide plate is open or closed. Each of the switches also have a sensor (SW1/PI9, SW3/PI3, and MS31/PI32) that acts as a backup and detects the same information as the switches. The error occurs when all the doors and guides are closed and there is a mismatch in readings between the sensors and the switches. For example, the front-finisher door is closed, PI32 senses the door is closed and MS31 senses the door is still open. Associated finisher door and guide switches and sensors are as follows: • Saddle-guide switch SW1 and saddleguide sensor PI9 • Booklet-ejection-door switch SW3 and booklet-ejection-door sensor PI3 • Front-door switch MS31 and front-door sensor PI32 |
| Remedy: | Control-panel diagnostics: PI32 (front-door-1 sensor), PI3 (booklet-door-1 sensor, also known as booklet-delivery door sensor), PI9 (front-door-2 sensor, also known as the saddle-guide-door sensor or inlet-door sensor), SW3 (booklet door 2) 1. Using the control-panel diagnostics, try to isolate which door or guide switch and sensor is causing the error. 2. Make sure that the sensors are securely fastened to the chassis. 3. Check the switches and sensors for damage and clean the sensors by gently blowing clean air into the sensor to remove dust and debris. 4. Check the wiring at the switches and sensors. 5. Check the tabs that activate the switches and sensors on the doors and guides for damage. Make sure that the tabs are aligned with the switches and sensors. Replace the doors and guides as necessary. 6. Verify that the following connectors are fully seated and not damaged: • Stacker controller PCA. • J719 (MS31) • J707 (PI32) • Saddle-stitcher controller PCA. • J4 (SW1) • J10 (PI9) • J4 (SW3) • J11 (PI3) 7. Only if the error persists and the previous steps fail to correct the problem, replace the PCA that is associated with the failed switch/sensor (stacker controller PCA or saddle-stitcher controller PCA). |
| Error code: | 66.12.51 |
| Display: | 66.12.<ZZ> Output accessory failure |
| Description: | This error is caused by failures in the output accessories. booklet bin motor failure (motor 10) in the multi functional finisher |
| Remedy: | - Follow the instructions in online help. - Turn the product off and turn it on. |
| Error code: | 66.12.52 |
| Display: | 66.12.52 |
| Description: | Finisher error - front booklet-stapler motor (M7) The booklet-maker stitch staplers do not move to different locations in relation to the paper like the main stapler. The only movement is through the movement of the rotary cam located on the stapler unit itself, during the actual stapling of the booklet. The stitch-home-position switch (SW7) is part of the front stitch stapler unit and senses the stapler opening and closing during stapling by the motion of the rotary drive cam. Like SW7, the stitch motor (M7) is also part of the overall stitch stapler unit and replacement requires the replacement of saddle-stapler assembly. Error occurs when the front booklet-maker stapler stitching home position sensor (SW7) does not turn on when the stitch motor (front) (M7) has been driven forward for 0.5 seconds. Also occurs when the front booklet-maker stapler-stitching home-position sensor (SW7) does not turn off when the stitch motor (front) (M7) has been driven forward for 0.5 seconds. |
| Remedy: | Control panel diagnostics: none 1. Check the front-stitch stapler for jammed staples, and then perform the following steps: • Clear jammed staples, and then check the staple unit for damage. Retest the stapler. • If the error continues, check the following items: Make sure that HP-approved staples are used. Replace the staple cartridge with one containing HPapproved staples. If the error continues, replace the saddle-stapler assembly. • If the error persists, but no damage is found, proceed to the next step. 2. If the error persists and no jammed staples are found, perform the following steps: • Verify that connector J8 on the saddle-stitcher controller PCA is fully seated and not damaged. Check the wiring at the rearsaddle- stitch stapler and the saddle-stapler assembly for damage and proper seating. Also inspect the connector that the saddle-stitch stapler assembly engages inside finisher, for damage and foreign material in the connector as well as for proper seating with the saddle-stitch stapler assembly. • Only if the error persists and the previous steps fail to correct the problem, replace the saddlestitcher controller PCA. |
| Error code: | 66.XY.ZZ |
| Display: | 66.XY.ZZ SERVICE ERROR |
| Description: | The external paper-handling controller has detected a problem. |
| Remedy: | Check the cables, and then turn the product off and then on. |
| Error code: | 68.X |
| Display: | 68.X STORAGE ERROR SETTINGS CHANGED |
| Description: | An error occurred in the product permanent storage and one or more product settings has been reset to its factory default. |
| Remedy: | Press OK to resume printing. Print a configuration page and check the product settings to determine which values have changed. If the error does not clear, turn the product off and then on. If the message persists, contact an HP-authorized service or support provider. |
| Error code: | 69.X |
| Display: | 69.X ERROR |
| Description: | A printing error occurred. |
| Remedy: | • Turn the product off and then on. • If the message persists, contact an HPauthorized service or support provider. |
| Error code: | 79.XXXX |
| Display: | 79.XXXX ERROR |
| Description: | The product detected a critical hardware error. |
| Remedy: | • Press the stop button to clear the print job from the product memory. Turn the product off and then on. • Try printing a job from a different program. If the job prints, go back to the first program and try printing a different file. If the message appears only with a certain program or print job, contact the software vendor for assistance. If the message persists with different programs and print jobs, try these steps. • Turn the product off. • Disconnect all cables to the product that connect it to the network or computer. • Remove all the memory DIMMs or thirdparty DIMMs from the product. Then reinstall the memory DIMM. • Remove the EIO device from the product. • Turn the product on. If the error no longer exists, follow these steps. • Install the DIMM and EIO device one at a time, making sure to turn the product off and then on as you install each device. • Replace the DIMM or EIO device if you determine that it causes the error. • Reconnect all cables that connect the product to the network or computer. |
| Error code: | 8X.YYYY |
| Display: | 8X.YYYY EMBEDDED JETDIRECT ERROR |
| Description: | The embedded HP Jetdirect print server has encountered a critical error. |
| Remedy: | • Turn the product off and then on. • If the message persists, contact an HPauthorized service or support provider. |
Название
HP Картридж со скрепками
HP 824A Тонер-картридж голубой
HP 824A Тонер-картридж желтый
HP 824A Тонер-картридж пурпурный
HP 824A Блок фотобарабана черный
HP 824A Блок фотобарабана голубой
HP 824A Блок фотобарабана желтый
HP 824A Блок фотобарабана пурпурный
HP 825A Тонер-картридж черный
HP Комплект закрепления (Печка) 220V
HP Комплект роликов
HP Комплект переноса изображения
HP Комплект роликов АПД
