HP Color LaserJet CM6049f MFP

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

200000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Телефон
Цветность печати	цветная
Печать фотографий
Сканер
Копир
Факс
Тип устройства	МФУ
Область применения	большой офис
Число страниц в месяц	200 000
Размещение	напольный
Тип	лазерный/светодиодный
Макс. формат	A3
Технология печати	лазерная
Принтер
Количество цветов	4
Время разогрева	112
Система непрерывной подачи чернил
Пигментные чернила
Прямая печать
Печать без полей
Двусторонняя печать
Макс, разрешение для ч/б печати
По X	1 200
По Y	600
Скорость ч/б печати
A3	23,5
A4	41
Время выхода первого отпечатка
Ч/б	11,5
Цветн,	11,5
Копир
Макс, количество копий за цикл	999
Значение масштаба
Минимальное	0,25
Максимальное	4
Макс, разрешение (ч/б)
По Y	600
По X	600
По X	300
По Y	300
Сканер
Устройство автоподачи оригиналов	одностороннее
Отправка изображения по e-mail
Стандарт WIA
Стандарт TWAIN
Емкость устройства автоподачи оригиналов	50
Тип сканера	планшетный/протяжный
Макс. формат оригинала	A3
Глубина цвета	30 бит
Оттенки серого	256
Макс, размер сканирования
По X	297
По Y	432
Разрешение сканера
По Х	600
Расходные материалы
Количество картриджей	4
Печать на:
Матовой бумаге
Карточках
Конвертах
Пленках
Глянцевой бумаге
Этикетках
Рулоне
CD/DVD
Фотобумаге
Плотность бумаги
Максимальная	220
Минимальная	60
Факс
Цветной
PC Fax
Макс, скорость передачи данных	33,6 Кбит/с
Телефон
Стандарт DECT
АОН
Спикерфон
Автоответчик
Caller ID
Проводная трубка
Беспроводная трубка
Языки управления
PostScript 2
PCL 6
PCL 5e
PPDS
PostScript 3
PCL 5c
PDF
PostScript	опционально
Лотки
Емкость лотка ручной подачи	100
Подача бумаги
Стандартная	2 100
Вывод бумаги
Стандартный	500
Финишер
Электронная сортировка
Сортировка со сдвигом
Степлер
Брошюровщик
Сортер
Интерфейсы
Ethernet (RJ-45)
USB
AirPrint
RS-232
Bluetooth
Инфракрасный порт
Wi-Fi 802.11n
Веб-интерфейс
Устройство для чтения карт памяти
Wi-Fi
FireWire (IEEE 1394)
LPT
Версия USB	2,0
Количество свободных слотов расширения	1
Количество слотов расширения	1
Память/Процессор
Процессор
Частота процессора	835
Объем памяти	512
Макс, объем памяти	768
Емкость жесткого диска	80
Дополнительная информация
Экран
Работа от аккумулятора
Поддержка ОС
Windows
Mac OS
DOS
Linux
Потребляемая мощность
В режиме ожидания	24,5
При работе	920
Уровень шума
При работе	56,8
В режиме ожидания	40,3
Габариты
Вес	145
Ширина	704
Высота	988
Глубина	673

Коды ошибок

10.00.YY

10.10.YY

10.90.XY

10.xx.yy

11.XX

13.01

13.02

13.05

13.06

13.10

13.11

13.12

13.12.11

13.12.12

13.12.13

13.12.14

13.12.15

13.12.16

13.12.17

13.12.21

13.12.41

13.12.42

13.12.43

13.12.44

13.12.45

13.12.46

13.12.51

13.12.52

13.12.61

13.12.62

13.13

13.1C

13.20

13.21

13.2B

13.2C

13.2D

13.2E

13.30

13.7C

13.7D

13.7E

13.80

13.90

13.JJ.NT

13.XX.YY

30.01.02

30.01.03

30.01.06

30.01.08

30.01.14

30.01.15

30.01.18

30.01.19

30.01.25

30.01.34

30.01.39

30.01.40

30.01.41

30.01.42

30.01.43

30.01.44

30.01.45

30.01.46

41.3

41.5

41.X

48.01

49.XXXXX

50.1

50.2

50.3

50.4

50.5

50.7

50.8

50.9

50.A

50.B

51.1Y

51.2Y

52.00

52.10

52.20

53.10.0X

54.01

54.15

54.16

54.17

54.18

55.00.YY

55.01.YY

55.02.YY

55.03.YY

55.04.YY

55.05

56.01

56.02

57.01

57.03

57.04

57.05

57.06

57.07

57.08

57.09

59.30

59.40

59.50

59.51

59.52

59.53

59.60

59.61

59.62

59.63

59.90

59.A0

59.C0

59.F0

59.XY

60.02

60.03

60.04

60.05

60.XX

65.12.99

66.00.15

66.12.01

66.12.02

66.12.03

66.12.11

66.12.12

66.12.13

66.12.14

66.12.15

66.12.16

66.12.21

66.12.22

66.12.23

66.12.31

66.12.32

66.12.34

66.12.41

66.12.42

66.12.43

66.12.44

66.12.45

66.12.46

66.12.47

66.12.51

66.12.52

66.XY.ZZ

68.X

69.X

79.XXXX

8X.YYYY

Описание

Парткод

Название

HP Картридж со скрепками

HP Комплект закрепления (Печка) 220V

HP Комплект роликов

HP Комплект переноса изображения

HP Тонер-картридж голубой

HP Тонер-картридж желтый

HP Тонер-картридж пурпурный

HP Блок фотобарабана черный

HP Блок фотобарабана голубой

HP Блок фотобарабана желтый

HP Блок фотобарабана пурпурный

HP Комплект роликов АПД

HP Тонер-картридж черный (контрактный)

Error code:	10.00.YY
Display:	10.XX.YY SUPPLY MEMORY ERROR
Description:	The MFP cannot read or write to at least one print cartridge e-label or an e-label is missing from a print cartridge. E-label is damaged.
Remedy:	1. Reinstall the print cartridge, or install a new HP print cartridge. 2. Verify that connector J97 on the DC controller PCA is firmly seated.

Error code:	10.10.YY
Display:	10.XX.YY SUPPLY MEMORY ERROR
Description:	The MFP cannot read or write to at least one print cartridge e-label or an e-label is missing from a print cartridge. MFP cannot communicate with the e-label.
Remedy:	1. Reinstall the print cartridge, or install a new HP print cartridge. 2. Verify that connector J97 on the DC controller PCA is firmly seated.

Error code:	10.90.XY
Display:	10.90.XY REPLACE <COLOR> CARTRIDGE
Description:	A toner replenishment malfunction has occurred.
Remedy:	Replace the print cartridge. If replacing the print cartridge does not fix the problem, replace the corresponding image drum.

Error code:	10.xx.yy
Display:	10.xx.yy Supply Memory Error
Description:	The product cannot read or write to at least one print cartridge e-label, or an e-label is missing from a print cartridge.
Remedy:	Reinstall the print cartridge, or install a new HP print cartridge.

Error code:	11.XX
Display:	11.XX INTERNAL CLOCK ERROR
Description:	The real time clock has experienced an error.
Remedy:	1. Power cycle the product to see if the message clears. 2. If possible, print a configuration page to record product information, and then perform an NVRAM initialization routine. If the initialization routine is successful, you will need to re-enter several configuration parameters (such as the page count and the serial number). 3. If the error persists, replace the formatter PCA.

Error code:	20
Description:	Vertical image or label drift
Causes:	The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media.
Remedy:	Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation.

Error code:	22
Description:	Loss of printing registration on labels. Excessive vertical drift in top-of-form registration.
Causes:	The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly.
Remedy:	Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58.

Error code:	40
Display:	Scanner locked
Description:	10-348 ERROR 40 FUSER MAIN LAMP FAILURE Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault, Clear <10-348 & 10-350> is run.
Causes:	1. Deformed paper sensor actuator or faulty sensor. 2. SMPS PBA or Main PBA is defective 3. Faulty cables or connectors.
Remedy:	Switch printer power OFF. Remove the Fuser Assembly. Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms? Y↓N→ Replace the Fuser Assembly. Reinstall Fuser. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the resistance between P404A-1 and P404A-2 on the Engine Control Board. Does the resistance measure between 20K and 100K ohms? Y↓N→ Repair or replace the wiring harness between the Engine Control Board and the Fuser. Replace the Engine Control Board.

Error code:	13.01
Display:	13.01 Paper feed 1, Paper late jam
Description:	• The leading edge of the paper fed from Tray 1 stopped before reaching the registration sensor (C). • The leading edge of the paper fed from Tray 2 stopped before reaching the registration sensor (B). • The leading edge of the paper fed from Tray 3 stopped before reaching the registration sensor (A-1). • The leading edge of the paper fed from Tray 4 stopped before reaching the registration sensor (A-2). • The leading edge of the paper fed from Tray 5 stopped before reaching the registration sensor (A-3).89A
Remedy:	Follow the onscreen instructions to locate and remove the paper or obstruction.

Error code:	13.12.11
Display:	13.12.11 Jam inside upper left door
Description:	Stapler jam. Initial jam at entry. At power-on, media was detected at SR2100 (inlet media sensor). SR2100 is located in the stapler/stacker feed assembly. SR2100 senses media entering the stapler/stacker.
Remedy:	1. Open the upper left door and remove any media. 2. Open the lower left door and remove any media. 3. Check connection J2104 on the stapler/ stacker control board. 4. Remove the stapler/stacker feed assembly and perform the following tasks. - Remove any media from SR2100. - Check the operation of the sensor flag and sensor-flag spring and make sure that the flag does not block the sensor. If the flag or the spring is damaged, replace the stapler/stacker feed assembly. - Clean SR2100 by blowing air gently into the sensing area. Check the sensor for correct mounting, cable connection, and alignment with the sensor flag. If the sensor is damaged or nor working, replace the sensor. - Check operation of the drive gears and belts at the rear of the stapler/ stacker feed assembly. Turning any of the gears should turn all of the rollers in the assembly. If the gears or belts are not working, replace the stapler/stacker feed assembly. 5. If, after performing the previous steps, the problem persists, replace the stapler/stacker control board.

Error code:	13.12.12
Display:	13.12.12
Description:	Finisher delay jam at PI33. The engine signals the finisher that paper is about to enter the finisher from the IPTU. The finisher`s upper-feed-path-entry sensor (PI33), which detects paper entering the finisher, does not detect the paper within the expected time period triggering the error.
Remedy:	Open the IPTU and the finisher top door and check the following items: • If media is found in the IPTU but has not reached the finisher, perform the following steps: • Remove and then reinstall the IPTU. Make sure that the connector is fully seated and that the IPTU is securely fastened. • If the error persists, replace the IPTU. • If media is jammed at the exit point of the IPTU (prior to entering the finisher), perform the following steps: • Verify that the finisher is securely fastened to the engine. • Make sure that the finisher and IPTU are correctly aligned. Adjust the finisher castors to obtain a uniform gap between the finisher and the engine. The engine-tofinisher gap must be the same at the bottom and the top so that the finisher is parallel to the engine. With the engine-to-finisher gap correct, make sure that the finisher paper path entry point is aligned with the IPTU exit point. • Check the finisher entry point guides for damage. • Verify that the finisher rollers are turning before the media leaves the IPTU. If the rollers are not turning, test motor M9 by using the finisher component test from the controlpanel display. If the motor does not activate during the test, check the connectors for motor M9 (inlet motor). Make sure that connector J705 is fully seated on the stacker controller PCA. If the error persists, replace motor M9 or the saddle paper-feeder assembly. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA. • If media is found in the finisher but has not reached sensor PI33, perform the following steps: • Check the upper and lower guides and rollers in the paper path for damage. • Make sure that the media diverter gate (saddle-stitch flapper) is not blocking the paper path. • If media is found in the finisher covering sensor PI33 (the sensor is not detecting the media), perform the following steps: • Check the sensor for obstructions. Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body• Make sure that the lower end of the flag is not damaged and is correctly positioned to activate the sensor. • Make sure that the sensor is securely fastened to the chassis. • Carefully clean the sensor body by gently blowing clean air across the sensor to remove dust and debris. • Verify that the wiring at the sensor is not damaged and that the intermediate connector J1007 and connector J708 on the stacker controller PCA are fully seated. Replace the sensor if necessary. • Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA.

Error code:	13.12.15
Display:	13.12.15
Description:	Finisher stay jam at PI34 Finisher`s upper-paper-path-exit sensor (PI34) remains activated longer than expected suggesting that paper has jammed at the sensor.
Remedy:	Control panel diagnostics: M31 (entrance motor), SL32 (buffer roller solenoid), and SL33 (output roller solenoid) 1. Remove any media in the upper paper path that might be activating sensor PI34. 2. Carefully clean the sensor body, by gently blowing clean air across the sensor to remove dust and debris. 3. Verify that the sensor flag is not damaged, moves freely, and is correctly aligned with the sensor body. 4. Lift-swing-guide assembly at the paperexit area to output bins and inspect for jammed paper, obstructions, or damage. 5. Run a diagnostic through the engine control panel and turn on M31 (entrance motor) to observe gear rotations on the upper-rear frame of the finisher. Ensure that the first-delivery rollers and buffer rollers that pass paper to and from PI34 are rotating. 6. Test SL32 (buffer-roller solenoid) and SL33 (output-roller solenoid) using the control panel diagnostics. 7. Check wiring from sensor PI34 to stacker-control board connector J707 for damage. 8. Only if the error persists and the previous steps fail to correct the problem, replace the stacker controller PCA.