HP LaserJet P1500
Рейтинг
Модули
Internal components (1 of 3)
HP LaserJet P1500 Series covers
Internal components (3 of 3)
Internal components (2 of 3)
Assembly locations
Детали Internal components (3 of 3)
Деталь: | Fusing assembly |
Парткод: | RM1-4208-000 |
Деталь: | Fusing assembly |
Парткод: | RM1-4209-000 |
Деталь: | engine control PCB assembly |
Парткод: | RM1-4627-000 |
Деталь: | engine control PCB assembly |
Парткод: | RM1-4628-000 |
Деталь: | formatter PCB assembly |
Парткод: | RM1-4216-000 |
Деталь: | formatter PCB assembly |
Парткод: | RM1-4217-000 |
Деталь: | SCREW, D, M3X6 |
Парткод: | XA9-1670-000 |
Деталь: | SCREW, W/WASHER, M3X6 |
Парткод: | XB2-7300-605 |
Деталь: | SCREW, W/WASHER, M3X8 |
Парткод: | XA9-1420-000 |
Цена: | 1 100 ₽ |
Деталь: | Cable contact |
Парткод: | RU5-2953-000 |
Деталь: | Formatter crossmember |
Парткод: | RC2-1513-000 |
Деталь: | Formatter crossmember |
Парткод: | RC2-1377-000 |
Деталь: | Tag cable guide |
Парткод: | RC2-1189-000 |
Деталь: | Dust cover |
Парткод: | RC2-1495-000 |
Деталь: | Cable guide |
Парткод: | RC2-1511-000 |
Деталь: | PCB plate |
Парткод: | RC2-1503-000 |
Деталь: | Cable guide |
Парткод: | RC2-1375-000 |
Деталь: | Insulating sheet |
Парткод: | RC2-1376-000 |
Деталь: | LEFT COVER |
Парткод: | RC2-1401-000 |
Деталь: | Dust cover |
Парткод: | RC2-1405-000 |
Деталь: | RIGHT COVER |
Парткод: | RC2-1400-000 |
Деталь: | FRONT COVER ASSEMBLY |
Парткод: | RL1-1506-000 |
Деталь: | Paper pick-up tray assembly |
Парткод: | RM1-4191-000 |
Деталь: | Paper delivery tray assembly |
Парткод: | RM1-4192-000 |
Деталь: | face-down cover assembly |
Парткод: | RM1-4193-000 |
Деталь: | Cartridge door assembly |
Парткод: | RM1-4194-000 |
Деталь: | CONTROL PANEL ASSEMBLY |
Парткод: | RM1-4195-000 |
Деталь: | SCREW, RS, M3X8 |
Парткод: | XA9-1504-000 |
Деталь: | LASER SCANNER ASSEMBLY |
Парткод: | RM1-4184-000 |
Деталь: | Motor control PCB assembly |
Парткод: | RM1-4635-000 |
Деталь: | SCREW, RS, M3X6 |
Парткод: | XB2-8300-609 |
Деталь: | DC24V motor |
Парткод: | RM1-4196-000 |
Деталь: | SCREW, RS, M3X10 |
Парткод: | XA9-1501-000 |
Деталь: | SCREW, D, M3X6 |
Парткод: | XA9-1670-000 |
Деталь: | Shaft support |
Парткод: | RC2-1236-000 |
Деталь: | Door hook |
Парткод: | RC2-1463-000 |
Деталь: | RFI plate |
Парткод: | RC2-1527-000 |
Деталь: | Scanner cover |
Парткод: | RC2-1381-000 |
Деталь: | Motor crossmember |
Парткод: | RC2-1505-000 |
Деталь: | Motor crossmember |
Парткод: | RC2-1223-000 |
Деталь: | FLAT CABLE |
Парткод: | RK2-1757-000 |
Деталь: | PAPER PICK-UP ASSEMBLY |
Парткод: | RM1-4204-000 |
Деталь: | TRANSFER ROLLER |
Парткод: | RC2-1483-000 |
Деталь: | SEPARATION PAD ASSEMBLY |
Парткод: | RM1-4207-000 |
Деталь: | Base plate assembly |
Парткод: | RM1-4199-000 |
Деталь: | PICK-UP ROLLER |
Парткод: | RL1-1497-000 |
Деталь: | SCREW, W/WASHER, M3X6 |
Парткод: | XB2-7300-605 |
Деталь: | SCREW, TAP, M4X10 |
Парткод: | XB4-5401-009 |
Деталь: | SCREW, D, M3X6 |
Парткод: | XA9-1670-000 |
Деталь: | COMPRESSION SPRING |
Парткод: | RU5-2972-000 |
Деталь: | Rear panel |
Парткод: | RC2-1435-000 |
Деталь: | Tag cover |
Парткод: | RC2-1205-000 |
Деталь: | formatter PCB assembly |
Парткод: | RM1-4216-000 |
Деталь: | formatter PCB assembly |
Парткод: | RM1-4217-000 |
Деталь: | engine control PCB assembly |
Парткод: | RM1-4627-000 |
Деталь: | engine control PCB assembly |
Парткод: | RM1-4628-000 |
Коды ошибок
01
02
03
04
05
06
07
08
09
Описание
Error code: | 01 |
Display: | ERROR CONDITION INVALID HEAD |
Description: | The ERROR light flashes. |
Causes: | The printhead was replaced with one that is not a genuine Zebra™ printhead. |
Remedy: | Install a genuine Zebra printhead. |
Error code: | 02 |
Display: | ERROR CONDITION RIBBON OUT |
Description: | The printer stops; the ERROR light flashes. |
Causes: | In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly. |
Remedy: | Load ribbon correctly. 1. Load ribbon correctly. See Load Ribbon on page 64. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Load media correctly. See Load Media on page 58. 2. Calibrate the sensors. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. 1. Print a sensor profile. See Print Sensor Profile on page 89. The ribbon out threshold (marked by the word RIBBON) is likely too high, above the black area that indicates where the ribbon is detected. 2. Calibrate the sensors or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. |
Error code: | 03 |
Display: | WARNING RIBBON IN |
Description: | The ERROR light flashes. |
Causes: | Ribbon is loaded, but the printer is set for direct thermal mode. |
Remedy: | Ribbon is not required with direct thermal media. If you are using direct thermal media, remove the ribbon. This error message will not affect printing. If you are using thermal transfer media, which requires ribbon, set the printer for Thermal Transfer mode. See Select Print Method on page 81. |
Error code: | 04 |
Display: | ERROR CONDITION PAPER OUT |
Description: | The printer stops; the ERROR light flashes. |
Causes: | The media is not loaded or is loaded incorrectly. Misaligned media sensor. The printer is set for noncontinuous media, but continuous media is loaded. |
Remedy: | Load media correctly. See Load Media on page 58. Check position of the media sensor. Install proper media type, or reset printer for current media type and perform calibration. |
Error code: | 05 |
Display: | ERROR CONDITION HEAD OPEN |
Description: | The printer stops; the ERROR light flashes. |
Causes: | The printhead is not fully closed. The head open sensor is not working properly. |
Remedy: | Replace the sensor. |
Error code: | 06 |
Display: | THERMISTOR FAULT |
Description: | The ERROR light flashes. |
Causes: | The printhead has a faulty thermistor. |
Remedy: | Replace the printhead. |
Error code: | 07 |
Display: | WARNING HEAD COLD, THERMISTOR FAULT, ERROR CONDITION HEAD ELEMENT BAD |
Description: | The printer stops; the ERROR light is on; the printer cycles through these three messages. |
Causes: | The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
Remedy: | Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
Error code: | 08 |
Display: | WARNING HEAD COLD |
Description: | The printer prints while the ERROR light flashes. |
Causes: | The printhead temperature is approaching its lower operating limit. The printhead data cable is not properly connected. The printhead has a faulty thermistor. |
Remedy: | Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the printer to a warmer area. Caution • Turn off (O) the printer before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the printer. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the printer. Replace the printhead. |
Error code: | 09 |
Display: | WARNING HEAD TOO HOT |
Description: | The printer stops; the ERROR light flashes. |
Causes: | The printhead is over temperature. |
Remedy: | Allow the printer to cool. Printing automatically resumes when the printhead elements cool to an acceptable operating temperature. |