KIP 7170

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

светодиодная

Макс. формат

Цветность печати

черно-белая

Характеристики
Коды ошибок

Общие характеристики
Сканер
Печать фотографий
Факс
Копир
Телефон
Тип устройства	Принтер
Макс. формат	A0
Цветность печати
Технология печати	светодиодная
Размещение	напольный
Тип	лазерный/светодиодный
Принтер
Пигментные чернила
Двусторонняя печать
Система непрерывной подачи чернил
Печать без полей
Время разогрева	240
Прямая печать
Макс, разрешение для ч/б печати
По X	600
Макс, разрешение для цветной печати
По Y	2 400
Время выхода первого отпечатка
Ч/б	18
Сканер
Стандарт WIA
Слайд-адаптер
Стандарт TWAIN
Отправка изображения по e-mail
Расходные материалы
Печать на:
Матовой бумаге
Рулоне
Пленках
Глянцевой бумаге
Конвертах
Карточках
CD/DVD
Фотобумаге
Этикетках
Плотность бумаги
Максимальная	110
Минимальная	40
Факс
Цветной
PC Fax
Телефон
Проводная трубка
Спикерфон
Беспроводная трубка
АОН
Caller ID
Автоответчик
Стандарт DECT
Языки управления
PostScript 3
PostScript 2
PostScript
PPDS
PCL 6
PCL 5c
PCL 5e
PDF
Финишер
Электронная сортировка
Степлер
Сортировка со сдвигом
Брошюровщик
Сортер
Интерфейсы
Ethernet (RJ-45)
USB
AirPrint
Устройство для чтения карт памяти
Веб-интерфейс
RS-232
Инфракрасный порт
FireWire (IEEE 1394)
Wi-Fi
Wi-Fi 802.11n
Bluetooth
LPT
Версия USB	2,0
Память/Процессор
Объем памяти	2 048
Макс, объем памяти	4 096
Дополнительная информация
Экран
Работа от аккумулятора
Поддержка ОС
Mac OS
Windows
DOS
Linux
Потребляемая мощность
При работе	1 200
В режиме ожидания	15
Габариты
Глубина	700
Высота	1 570
Вес	244
Ширина	1 590

Коды ошибок

E-0101h, E-257

E-0301h, E-769

E-0302h, E-770

E-0310h, E-784

E-0320h, E-800

E-0321h, E-801

E-0322h, E-802

E-0323h, E-803

E-0330h, E-816

E-0331h, E-817

E-0332h, E-818

E-0335h, E-821

E-0336h, E-822

E-0800h, E-2048

E-0900h, E-2304

E-0901h, E-2305

E-0903h, E-2307

E-0920h, E-2336

E-0A00h, E-2560

E-0A20h, E-2592

E-0A41h, E-2625

J-00000002

J-00000100

J-00000200

J-04000000

J-08000000

J-10000000

Error code:	E-0101h, E-257
Description:	Cutter Error
Causes:	1. The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to “H” within 100 millisecond since the Cutter has started the operation. 2. The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to “L” within 1 second since the Cutter has started the operation.
Remedy:	Wires 1 Is the wire between Cutter Unit and PW14420 PCB connected properly? No Connect it properly. Cutter Home Position Sensors (MS6 & MS7) 2 Check the status of the following signals in Input Check of the Service Mode. Cutter Home Position Signal Code : 00094 MS_CUTR (Right) 00095 MS_CUTL (Left) Is the status “L” when the Cutter is at each home position? No Replace the Cutter Unit. Developer Press Sensor (PH4) 3 Check the operation of Cutter in Output Check of the Service Mode. Device Code : 00027 M5-CUTL (Cutter Motor 1) 00028 M5-CUTR (Cutter Motor 2) Does the Cutter operate? No Replace the Cutter Unit.

Error code:	E-0301h, E-769
Description:	Process 1 Developer Set Motor Error
Causes:	The Developer Press Sensor Signal (PRESS_S) does not change to “L” within 30 seconds after turning on.
Remedy:	Wires 1 Are the wires among Developer Press Sensor (PH4), PW14420 PCB and Developer Press Motor (M4) connected properly? No Connect them properly. Developer Press Motor (M4) 2 Turn off the machine, and then turn it on again. Is the Developer Unit moved to the Drum side? No Replace the Developer Press Motor. Developer Press Sensor (PH4) 3 Select the Signal Code “00104 PRESSS” (Developer Press Sensor) in Input Check, and then turn on the machine again. Does the status change from “H” to “L” after turning on? No Replace the Developer Press Sensor. Fuse 4 Does the fuse (F3) have a proper conductivity? No Replace the fuse (F3).

Error code:	E-0302h, E-770
Description:	Process 1 Developer Drum Motor Error
Causes:	The Main Motor Output Detection Signal (MAINM_LD) continues to be “H” for 3 seconds or longer when the Main Motor is rotating.
Remedy:	Wires 1 Is the wire between Main Motor and PW14420 PCB connected properly? No Connect it properly. DC Power Supply (DCP1) or Fuse 2 Confirm that the machine is turned on, and then check the voltage of the orange line (J220-4). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Main Motor (M1) 3 Check the operation of Main Motor in Output Check of the Service Mode. Device Code : 00000 MAIN-TRG (Main Motor) Does the Main Motor operate correctly? No Replace the Main Motor.

Error code:	E-0310h, E-784
Description:	Out of Process 1 Developer Error
Causes:	1. The Connector J-253 is not connected. 2. The Switch (MS4) is “open” condition, which detects open/close of Engine Unit or Toner Hatch.
Remedy:	Wires 1 Is the wire between Developer Unit and PW14420 PCB connected properly? No Connect it properly. Switch (MS4) 2 Is the actuator of Switch correctly pressed down when you close the Engine Unit or Toner Hatch? No Adjust the positions of Switch (or Toner Hatch and Engine Unit).

Error code:	E-0320h, E-800
Description:	Abnormal output of Process 1 1st Charger
Causes:	The Image Corona Output Detection Signal (IM_LD) continues to be “L” for 1 second or longer when the Image Corona is ON.
Remedy:	Wires 1 Are wires among Image Corona, HV Power Supply PCB and PW14420 PCB connected properly? No Connect them properly. Image Corona 2 Is the Image Corona dirty? Yes Clean each Corona Wire, Grid Plate and housing. Cleaning Roller 3 Does the bias terminal plate touch to Cleaning Roller shaft properly? No Remove and reapply conductive grease to Cleaning Roller shaft. Relocate the bias terminal plates properly. Is grease applied enough? No Remove and reapply conductive grease to Cleaning Roller shaft. Transfer Corona 4 Is the Transfer Corona dirty? Yes Clean each Corona Wire and housing. Is the Corona Wire broken? Yes Replace the Corona Wire. Separation Corona 5 Is the Separation Corona dirty? Yes Clean each Corona Wire and housing. Is the Corona Wire broken? Yes Replace the Corona Wire. HV Power Supply 6 Can you fix the problem if you replace the HV Power Supply? Yes OK

Error code:	E-0901h, E-2305
Description:	Fuser Over-Temp Error
Causes:	Fuser Temperature reaches over 230 °C.
Remedy:	Error clearance 1 Have you cleared the fuser error in the Error Clear Mode? (Refer to 8.11 Clear/Reset) Yes Wait until the Fuser Unit is enough cooled down. Then select the Error Clear Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1, H2), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Solid State Relay (SSR1) 3 Does the error occur again even if you have cleared it in the Error Clear Mode? Yes Replace the Solid State Relay. Thermistors (TH1 & TH2) 4 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor.

Error code:	J-00000100
Description:	Middle Paper Feed Jam
Causes:	1. Either Cutter Sensor Signal (P_CUT) or Roll Paper Size Signal (SZDATA0) does not change from H to L within a specified time since the machine has started to feed the roll paper from the specified position. 2. Either Cutter Sensor Signal (P_CUT) or Roll Paper Size Signal (SZDATA0) does not change from L to H within a specified time since the machine has started to rewind the roll paper.
Remedy:	Jam 1 Did a jam occur between Cutter Unit and Paper Gate Roller? Yes Remove the paper. Sensors (PH3A,PH4,PH5) 2 Check the status of following sensors in Input Check. 1. Roll Media Sensor SZDATA0 : PH3A (Signal Code: 000fh) 2. Cutter Area Paper Sensor P_CUT : PH4 (Signal Code: 000ah) 3. Paper EntryS ensor P_ENTER : PH5 (Signal Code: 000bh) Is the status “H” when each sensor does not detect the paper? And is it “L” when each sensor detects the paper? NOTE Refer to [8.6 Input Check]. No 1. Check the wire of sensor of which status is abnormal. 2. If the wire has no problem, replace the abnormal sensor with the new one. Paper Gate Sensor (PH6) 3 Check the status of Paper Gate Sensor (P_GATE). Check the voltage at J210-20 on DC Controller PCB (PW13720). Is it “0V” when the Paper Gate Sensor detects the paper? No 1. Check the wire of Paper Gate Sensor. 2. If the wire has no problem, replace the Paper Gate Sensor with the new one. Driving Part (MC3) 4 Select Output Check, and try to make the following parts work alone. 1. Paper Gate Clutch GATECL : MC3 (Signal Code: 0028h) And also, check whether or not the following parts work by just looking while making a print. 2. Main Motor 3. Roll Feed Motor Is there any part that does not work? NOTE Refer to [8.7 Output Check] Yes Replace the defective part with the new one.

Error code:	J-00000200
Description:	Registration Part Jam
Causes:	Input Check Mode No. 00503 Regist Sensor 1 (“H” = Detected) Input Check Mode No. 00504 Regist Sensor 2 (“H” = Detected) Input Check Mode No. 00505 Regist Sensor 3 (“H” = Detected)
Remedy:	1 Have you removed all jammed sheets in the media path? No Clear the media path. Status 2 Sensor status is detected correctly. “H” = Paper Detected “L” =Paper Absence Yes OK Sensor 3 Replacing relevant sensor recovers Jam Status. Regist 1 Sensor (PH63) Regist 2 Sensor (PH64) Regist 3 Sensor (PH65) Yes OK PW13555 4 Replacing PW13555 recovers Jam Status. Yes OK Main Control PCB (PW13520) 5 Replacing PW13520 PCB recovers Jam Status. Yes OK

Error code:	J-04000000
Description:	Exit Part (Top Front) Jam
Causes:	Input Check Mode No. 00603 Upper Exit Encoder (“H” = Detected)
Remedy:	1 Have you removed all jammed sheets in the media path? No Clear the media path. Status 2 Sensor status is detected correctly. “H” = Paper Detected “L” =Paper Absence Yes OK Sensor 3 Replacing relevant sensor recovers Jam Status. Upper Exit Pulse Sensor (PH89) Yes OK PW13555 4 Replacing PW13555 recovers Jam Status. Yes OK Main Control PCB (PW13520) 5 Replacing PW13520 PCB recovers Jam Status. Yes OK

KIP 7170

Общие характеристики

Сканер

Печать фотографий

Факс

Копир

Телефон

Тип устройства

Макс. формат

Цветность печати

Технология печати

Размещение

Тип

Принтер

Пигментные чернила

Двусторонняя печать

Система непрерывной подачи чернил

Печать без полей

Время разогрева

Прямая печать

Макс, разрешение для ч/б печати

Макс, разрешение для цветной печати

Время выхода первого отпечатка

Сканер

Стандарт WIA

Слайд-адаптер

Стандарт TWAIN

Отправка изображения по e-mail

Расходные материалы

Печать на:

Плотность бумаги

Факс

Цветной

PC Fax

Телефон

Проводная трубка

Спикерфон

Беспроводная трубка

АОН

Caller ID

Автоответчик

Стандарт DECT

Языки управления

Финишер

Электронная сортировка

Степлер

Сортировка со сдвигом

Брошюровщик

Сортер

Интерфейсы

Ethernet (RJ-45)

USB

AirPrint

Устройство для чтения карт памяти

Веб-интерфейс

RS-232

Инфракрасный порт

FireWire (IEEE 1394)

Wi-Fi

Wi-Fi 802.11n

Bluetooth

LPT

Версия USB

Память/Процессор

Объем памяти

Макс, объем памяти

Дополнительная информация

Экран

Работа от аккумулятора

Поддержка ОС

Потребляемая мощность

Габариты

Глубина

Высота

Вес

Ширина

Коды ошибок

Описание

Позвонить

Написать