Brother MFC-8480DN
Рейтинг
Модули
DRIVE
COVERS
ADF
FRAME L & DRIVE UNIT
PAPER FEEDER
ADF1
DUPLEX
FUSER UNIT
OTHERS
PCB
LASER UNIT
PANEL
ADF2
FRAME L
SCANNER
FRAME UNIT
PAPER TRAY
Детали DUPLEX
| Деталь: | Cover, HIP (M880) |
| Парткод: | 087320616 |
| Деталь: | JOINT COVER ASSY, GRAY(1581), DCP8080DN/ DCP8085DN |
| Парткод: | LS7307001 |
| Деталь: | JOINT COVER ASSY, GRAY(1581), MFC8480DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LS7239001 |
| Деталь: | TAPTITE, BIND B M4X12 |
| Парткод: | 85411216 |
| Деталь: | SPEAKER ASSY |
| Парткод: | LG6529001 |
| Деталь: | DRIVER PCB ASSY |
| Парткод: | LG6531001 |
| Деталь: | SIDE COVER R, GRAY(1736) |
| Парткод: | LF9624001 |
| Деталь: | SIDE COVER L, GRAY(1736) |
| Парткод: | LF9625001 |
| Деталь: | ACCESS COVER, GRAY(1736) |
| Парткод: | LM5273001 |
| Деталь: | BACK COVER |
| Парткод: | LU7046001 |
| Деталь: | OUTER CHUTE ASSY |
| Парткод: | LU7047001 |
| Деталь: | REAR CHUTE ASSY |
| Парткод: | LU7126001 |
| Деталь: | TAPTITE CUP B M3X8 |
| Парткод: | 87310816 |
| Деталь: | PROCESS UNIT OP LABEL FOR US/ CAN/ ARG/ CHL/ BRA |
| Парткод: | LS7388001 |
| Деталь: | PROCESS UNIT OP LABEL FOR GER/ UK/ FRA/ BEL/ NLD/ CHE/ AUS/ ITA/ POL/ RUS/ PND/ IBR/ EEU, EXCEPT FOR MFC8881DNHY |
| Парткод: | LU7341001 |
| Деталь: | PROCESS UNIT OP LABEL FOR CHN |
| Парткод: | LS7919001 |
| Деталь: | PROCESS UNIT OP LABEL FOR PHL/ TUR/ ASA/ GUL/ KOR/ IND/ ARL/ NZ |
| Парткод: | LU7496001 |
| Деталь: | PROCESS UNIT OP LABEL, MFC8881DNHY |
| Парткод: | LX2209001 |
| Деталь: | FUSER CAUTION LABEL |
| Парткод: | LU7303001 |
| Деталь: | EXT CAP, MFC8480DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8890DW FOR US/ CAN/ CHE/ CHN/ PHL/ TUR/ POL/ ARG/ CHL/ ASA/ GUL/ BRA/ KOR/ IND/ RUS/ ARL/ NZ/ PND/ IBR/ EEU |
| Парткод: | LE8842001 |
| Деталь: | MJ COVER EXT, MFC8880DN/ MFC8881DNHY/ MFC8890DW FOR GER/ UK/ FRA/ BEL/ NLD/ AUS/ ITA |
| Парткод: | UF5745000 |
| Деталь: | USB HOST PCB |
| Парткод: | LT0668001 |
| Деталь: | PAPER STACK LEVER SP ASSY |
| Парткод: | LU7312001 |
| Деталь: | SUPPORT FLAP 2 |
| Парткод: | LU7118001 |
| Деталь: | Узел захвата/подачи бумаги из автоподатчика документов, в сборе |
| Парткод: | LE2919001 |
| Деталь: | MAIN FRAME L UNIT |
| Парткод: | LX2517001 |
| Деталь: | GEAR 17 MP ROLLER DRIVE |
| Парткод: | LM5104001 |
| Деталь: | GEAR 20 T1 ROLLER DRIVE |
| Парткод: | LM5103001 |
| Деталь: | GEAR 17 FEED ROLLER DRIVE |
| Парткод: | LM5102001 |
| Деталь: | DX GEAR 15 TRAY DRIVE |
| Парткод: | LM5051001 |
| Деталь: | DEVELOP JOINT |
| Парткод: | LU7214001 |
| Деталь: | MAIN MOTOR ASSY AL |
| Парткод: | LM5047001 |
| Цена: | 2 500 ₽ |
| Деталь: | FUSER GEAR 39 H/R DRIVE |
| Парткод: | LM5048001 |
| Цена: | 600 ₽ |
| Деталь: | REGISTER SOLENOID ASSY |
| Парткод: | LM5058001 |
| Деталь: | MP SOLENOID ASSY |
| Парткод: | LM5062001 |
| Цена: | 1 700 ₽ |
| Деталь: | T1 SOLENOID ASSY |
| Парткод: | LM5067001 |
| Деталь: | TONER SENSOR PCB ASSY |
| Парткод: | LJ9935001 |
| Деталь: | PT SENSOR HOLDER |
| Парткод: | UL9037001 |
| Деталь: | RELAY FRONT PCB ASSY |
| Парткод: | LV0690002 |
| Деталь: | FRONT COVER SW ASSY |
| Парткод: | LJ9940001 |
| Деталь: | RELAY REAR PCB ASSY |
| Парткод: | LJ9942001 |
| Деталь: | NEW TONER ACTUATOR |
| Парткод: | LM5085001 |
| Деталь: | NEW TONER ACTUATOR SPRING |
| Парткод: | LM5086001 |
| Деталь: | RUBBER FOOT |
| Парткод: | LJ7403001 |
| Деталь: | CONNECTOR |
| Парткод: | LJ9945001 |
| Деталь: | EJECTOR SOLENOID |
| Парткод: | LM5011001 |
| Деталь: | TAPTITE CUP S M3X6 |
| Парткод: | 87320616 |
| Деталь: | TAPTITE BIND B M3X10 |
| Парткод: | 85311016 |
| Деталь: | THERMISTOR ASSY |
| Парткод: | LG4518001 |
| Деталь: | DEV GEAR 37R JOINT DRIVE |
| Парткод: | LM5043001 |
| Деталь: | DRIVE RELEASE LINK |
| Парткод: | LM5080001 |
| Деталь: | DRIVE RELEASE CAM |
| Парткод: | LM5079001 |
| Деталь: | TAPTITE CUP B M2X6 |
| Парткод: | 87210616 |
| Деталь: | PE EG SENSOR ASSY |
| Парткод: | LM9001001 |
| Деталь: | PE ACTUATOR ASSY |
| Парткод: | LU7935001 |
| Деталь: | EDGE ACTUATOR |
| Парткод: | LM5132001 |
| Цена: | 170 ₽ |
| Деталь: | EDGE ACTUATOR SPRING |
| Парткод: | LM5133001 |
| Деталь: | ROLLER HOLDER ASSY |
| Парткод: | LU7179001 |
| Деталь: | REGIST ACTUATOR FRONT |
| Парткод: | LM5150001 |
| Цена: | 80 ₽ |
| Деталь: | REGIST ACTUATOR REAR |
| Парткод: | LM5151001 |
| Цена: | 80 ₽ |
| Деталь: | REGIST ACTUATOR SPRING |
| Парткод: | LM5152001 |
| Цена: | 30 ₽ |
| Деталь: | MP PE SENSOR ASSY |
| Парткод: | LJ9999001 |
| Деталь: | MP ROLLER HOLDER ASSY |
| Парткод: | LU7184001 |
| Деталь: | PE ACTUATOR MP |
| Парткод: | LM5171001 |
| Деталь: | PE ACTUATOR MP B 2 |
| Парткод: | LU0027001 |
| Деталь: | MP SEPARATION SPRING |
| Парткод: | LM6490001 |
| Деталь: | SEPARATION PAD ASSY MP |
| Парткод: | LM6752001 |
| Деталь: | TRAY MP ASSY |
| Парткод: | LM5196005 |
| Деталь: | MP TRAY COVER ASSY, DCP8080DN/ DCP8085DN/ MFC8480DN/ MFC8680DN |
| Парткод: | LS7305001 |
| Деталь: | MP TRAY COVER ASSY, MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LS7004001 |
| Деталь: | PROCESS COVER ASSY EXCEPT FOR CHN/ IND, EXCEPT FOR MFC8881DNHY |
| Парткод: | LU7037001 |
| Деталь: | PROCESS COVER ASSY FOR CHN, MFC8881DNHY |
| Парткод: | LU7527001 |
| Деталь: | PROCESS COVER ASSY FORIND |
| Парткод: | LU7689001 |
| Деталь: | TAPTITE BIND B M3X8 |
| Парткод: | 85310816 |
| Деталь: | BROTHER EMBLEM COVER ASSY, DCP8080DN/ DCP8085DN/ MFC8480DN/ MFC8680DN |
| Парткод: | LS7306001 |
| Деталь: | BROTHER EMBLEM COVER ASSY, MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LS7283001 |
| Деталь: | PROCESS COVER STOPPER |
| Парткод: | LM5124001 |
| Деталь: | SUPPORT FLAP 1 |
| Парткод: | LU7039001 |
| Деталь: | TAPTITE CUP B M4X10 |
| Парткод: | 87411016 |
| Деталь: | ADF UNIT LGL SX (SP), DCP8080DN/ MFC8480DN |
| Парткод: | LS7634001 |
| Деталь: | ADF UNIT LGL DX (SP), DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LS7633001 |
| Деталь: | HINGE ASSY L |
| Парткод: | LF9703001 |
| Деталь: | TAPTITE CUP B M3X10 |
| Парткод: | 87311016 |
| Деталь: | TAPTITE CUP S M3X12 |
| Парткод: | 87321217 |
| Деталь: | HINGE ARM R |
| Парткод: | LS7497001 |
| Деталь: | TAPTITE BIND B M4X12 |
| Парткод: | 85411216 |
| Деталь: | ADF EMBLEM, DCP8080DN/ DCP8085DN |
| Парткод: | LS7326001 |
| Деталь: | ADF EMBLEM, MFC8480DN/ MFC8680DN/ MFC8880DN/ MFC8881DNHY |
| Парткод: | LS7325001 |
| Деталь: | ADF EMBLEM, MFC8690DW/ MFC8890DW |
| Парткод: | LS7323001 |
| Деталь: | DOCUMENT COVER LGL SUB ASSY |
| Парткод: | LS7294001 |
| Деталь: | TAPTITE, CUP S M3X8 SR |
| Парткод: | LP2378001 |
| Деталь: | ADF SIDE COVER F |
| Парткод: | LS7258001 |
| Деталь: | ADF SIDE COVER R |
| Парткод: | LF9697001 |
| Деталь: | ADF COVER ASSY SX, DCP8080DN/ MFC8480DN |
| Парткод: | LF9700001 |
| Деталь: | ADF COVER ASSY DX, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LF9754001 |
| Деталь: | DOCUMENT HOLD ASSY |
| Парткод: | LE8834001 |
| Деталь: | DOCUMENT HOLD SPRING |
| Парткод: | LF2026001 |
| Деталь: | TAPTITE, CUP B M3X10 |
| Парткод: | LP2320001 |
| Деталь: | ADF HARNESS ASSY ALEFB SX, DCP8080DN/ MFC8480DN |
| Парткод: | LT0948001 |
| Деталь: | ADF HARNESS ASSY ALEFB DX, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890CW |
| Парткод: | LT0946001 |
| Деталь: | DOCUMENT EJECTION TRAY |
| Парткод: | LF9647001 |
| Деталь: | DOCUMENT COVER SENSOR |
| Парткод: | LG3218001 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | UF9009001 |
| Деталь: | EJECTION ROLLER B4 |
| Парткод: | UL6244002 |
| Деталь: | HINGE BASE R |
| Парткод: | LE6245001 |
| Деталь: | TAPTITE, CUP B M3X10 |
| Парткод: | 87311016 |
| Деталь: | DX FEED ASSY LTR FOR US/ CAN/ PHL/ ARG/ CHL/ BRA |
| Парткод: | LM5209001 |
| Деталь: | DX FEED ASSY A4 FOR GER/ UK/ FRA/ BEL/ NLD/ CHE/ AUS/ ITA/ CHN/ TUR/ POL/ ASA/ GUL/ KOR/ IND/ RUS/ ARL/ NZ/ PND/ IBR/ EEU |
| Парткод: | LU7503001 |
| Цена: | 3 200 ₽ |
| Деталь: | Main PCB Assembly |
| Парткод: | LU7939001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LU7941001 |
| Деталь: | 2 |
| Парткод: | LU7164001 |
| Деталь: | 4 |
| Парткод: | LU7078001 |
| Деталь: | 4 |
| Парткод: | LU7154001 |
| Деталь: | ROLLER HOLDER SP ASSY |
| Парткод: | LU7338001 |
| Деталь: | MP ROLLER HOLDER SP ASSY |
| Парткод: | LU7339001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0673001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0754004 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0673004 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0839020 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0753020 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0755001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0839001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0754001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0753001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0753004 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0867001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LT0867003 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG5923054 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG5923065 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG5923056 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG6190005 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG6872003 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG6190006 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG6190009 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG6198003 |
| Деталь: | Main PCB Assembly |
| Парткод: | LV0292001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LV0328001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LU7519001 |
| Цена: | 4 700 ₽ |
| Деталь: | Main PCB Assembly |
| Парткод: | LV0437001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LJ9978001 |
| Цена: | 3 300 ₽ |
| Деталь: | 4 |
| Парткод: | LM5867001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LG5921001 |
| Деталь: | LASER UNIT (SP) |
| Парткод: | LU7176001 |
| Цена: | 14 500 ₽ |
| Деталь: | TAPTITE, CUP S M3X6 |
| Парткод: | 87320616 |
| Деталь: | LASER CAUTION LABEL EXCEPT FOR CHN |
| Парткод: | LJ0908001 |
| Деталь: | LASER CAUTION LABEL FOR CHN |
| Парткод: | UL7931001 |
| Деталь: | PANEL UNIT, DCP8080DN/DCP8085DN EXCEPT FOR CHN |
| Парткод: | LS7312001 |
| Деталь: | PANEL UNIT, MFC8480DN/MFC8680DN/MFC8690DW/MFC8880DN/MFC8881DNHY/ MFC8890DW EXCEPT FOR CHN |
| Парткод: | LS7247001 |
| Деталь: | PANEL UNIT, DCP8085DN FOR CHN |
| Парткод: | LX2064001 |
| Деталь: | PANEL UNIT, MFC8880DN FOR CHN |
| Парткод: | LS7929001 |
| Деталь: | PANEL COVER ASSY, DCP8080DN FOR US/CAN |
| Парткод: | LS7309001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR US/UK/FRA/BEL/NLD/ARL/NZ/ PND/EEU (ENGLISH) |
| Парткод: | LS7608001 |
| Деталь: | PANEL COVER ASSY, MFC8480DN FOR US/CAN |
| Парткод: | LS7316001 |
| Деталь: | PANEL COVER ASSY, MFC8680DN FOR US |
| Парткод: | LX2013001 |
| Деталь: | PANEL COVER ASSY, MFC8690DW FOR US |
| Парткод: | LX2701001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR US/CAN/ARL/NZ |
| Парткод: | LS7248001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR GER/CHE |
| Парткод: | LS7674001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR GER/CHE/AUS |
| Парткод: | LS7667001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR GER/CHE/AUS |
| Парткод: | LS7679001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR UK/FRA/BEL/NLD/GUL/EEU (ENGLISH) |
| Парткод: | LS7563001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR UK/FRA/BEL/NLD (ENGLISH) |
| Парткод: | LS7640001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR FRA/BEL/NLD/CHE (FRENCH) |
| Парткод: | LS7609001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR FRA/BEL/NLD/CHE (FRENCH) |
| Парткод: | LS7564001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR FRA/BEL/NLD/CHE (FRENCH) |
| Парткод: | LS7641001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR FRA/BEL/NLD (DUTCH) |
| Парткод: | LS7610001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR FRA/BEL/NLD (DUTCH) |
| Парткод: | LS7565001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR FRA/BEL/NLD (DUTCH) |
| Парткод: | LS7642001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR ITA |
| Парткод: | LS7604001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR ITA |
| Парткод: | LS7558001 |
| Деталь: | PANEL COVER ASSY, MFC8881DNHY FOR ITA |
| Парткод: | LX2211001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR ITA |
| Парткод: | LS7638001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR CHN |
| Парткод: | LX2026001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR CHN |
| Парткод: | LS7920001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR PHL/ASA/IND/ARL/NZ |
| Парткод: | LS7994001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR TUR |
| Парткод: | LS7939001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR TUR |
| Парткод: | LS7981001 |
| Деталь: | PANEL COVER ASSY, DCP8080DN FOR ARG |
| Парткод: | LS7930001 |
| Деталь: | PANEL COVER ASSY, MFC8480DN FOR ARG/CHL |
| Парткод: | LS7952001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR ARG/CHL |
| Парткод: | LX2008001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR POL |
| Парткод: | LS7983001 |
| Деталь: | PANEL COVER ASSY, DCP8080DN FOR BRA |
| Парткод: | LX2084001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR BRA |
| Парткод: | LX2074001 |
| Деталь: | PANEL COVER ASSY, MFC8480DN FOR BRA |
| Парткод: | LX2077001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR BRA |
| Парткод: | LX2080001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR KOR |
| Парткод: | LX2054001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR RUS |
| Парткод: | LS7943001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR RUS |
| Парткод: | LS7990001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR PND |
| Парткод: | LS7664001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR PND |
| Парткод: | LS7682001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR ARG/CHL/IBR (SPANISH) |
| Парткод: | LS7614001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR IBR (SPANISH) |
| Парткод: | LS7566001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR IBR (SPANISH) |
| Парткод: | LS7645001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR IBR (PORTUGUESE) |
| Парткод: | LS7615001 |
| Деталь: | PANEL COVER ASSY, MFC8880DN FOR IBR (PORTUGUESE) |
| Парткод: | LS7567001 |
| Деталь: | PANEL COVER ASSY, MFC8890DW FOR IBR (PORTUGUESE) |
| Парткод: | LS7646001 |
| Деталь: | PANEL COVER ASSY, DCP8085DN FOR EEU |
| Парткод: | LX2051001 |
| Деталь: | TAPTITE CUP B M4X12 |
| Парткод: | 87411216 |
| Деталь: | PRINTED RUBBER KEY, DCP8080DN/DCP8085DN |
| Парткод: | LS7313001 |
| Деталь: | PRINTED RUBBER KEY, MFC8480DN/MFC8680DN/MFC8690DW/MFC8880DN/ MFC8881DNHY/MFC8890DW |
| Парткод: | LS7272001 |
| Деталь: | PANEL PCB ASSY, DCP8080DN/DCP8085DN EXCEPT FOR CHN |
| Парткод: | LT0695002 |
| Деталь: | PANEL PCB ASSY, MFC8480DN/MFC8680DN/MFC8690DW/MFC8880DN/ MFC8881DNHY/MFC8890DW EXCEPT FOR CHN |
| Парткод: | LT0695001 |
| Деталь: | PANEL PCB ASSY, DCP8085DN FOR CHN |
| Парткод: | LT0964002 |
| Деталь: | PANEL PCB ASSY, MFC8880DN FOR CHN |
| Парткод: | LT0964001 |
| Деталь: | LCD EXCEPT FOR CHN |
| Парткод: | A62006001 |
| Деталь: | LCD FOR CHN |
| Парткод: | A62027001 |
| Деталь: | BACK LIGHT MODULE |
| Парткод: | LG6550001 |
| Деталь: | LCD COVER |
| Парткод: | LF9709001 |
| Деталь: | PANEL INSULATION SHEET |
| Парткод: | LX2082001 |
| Деталь: | ADDRESS LABEL, MFC8480DN/MFC8680DN/MFC8690DW/MFC8880DN/ MFC8881DNHY/MFC8890DW EXCEPT FOR CHN |
| Парткод: | LF9717002 |
| Деталь: | ADDRESS LABEL, MFC8880DN FOR CHN |
| Парткод: | LP2637003 |
| Деталь: | ADDRESS LABEL, MFC8880DN/MFC8890DW FOR IBR |
| Парткод: | LP2189002 |
| Деталь: | ADF CHUTE ASSY SX, DCP8080DN/ MFC8480DN |
| Парткод: | LS7296001 |
| Деталь: | ADF CHUTE ASSY DX, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LS7297001 |
| Деталь: | ADF MOTOR |
| Парткод: | LE8688001 |
| Деталь: | S/ B SOLENOID ASSY, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LP2353001 |
| Деталь: | PF SOLENOID ASSY, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LP2354001 |
| Деталь: | ADF RELAY PCB, DCP8080DN/ MFC8480DN |
| Парткод: | LG6537001 |
| Деталь: | ADF RELAY PCB, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LG6537002 |
| Деталь: | UPPER MAIN CHUTE ASSY |
| Парткод: | LF9666001 |
| Деталь: | LOWER MAIN CHUTE ASSY, DCP8080DN/ MFC8480DN |
| Парткод: | LF9669001 |
| Деталь: | LOWER MAIN CHUTE ASSY, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LF9741001 |
| Деталь: | EXIT ROLLER ASSY |
| Парткод: | LF9673001 |
| Деталь: | LF ROLLER3 ASSY |
| Парткод: | LF9675001 |
| Деталь: | LF ROLLER4 ASSY |
| Парткод: | LF9677001 |
| Деталь: | FLAP ASSY, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LF9743001 |
| Деталь: | PAPER FEED CHUTE ASSY, DCP8080DN/ MFC8480DN |
| Парткод: | LF9681001 |
| Деталь: | PAPER FEED CHUTE ASSY, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LF9747001 |
| Деталь: | EXIT CHUTE COVER ASSY |
| Парткод: | LF9692001 |
| Деталь: | LF ROLLER1 ASSY |
| Парткод: | LP2448001 |
| Деталь: | PF ROLLER HOLDER ASSY |
| Парткод: | LS1030001 |
| Цена: | 3 100 ₽ |
| Деталь: | SB ROLLER ASSY, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LF9749001 |
| Деталь: | SB CHUTE ASSY, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LF9751001 |
| Деталь: | TAPTITE CUP S M3X8 SR |
| Парткод: | LP2378001 |
| Деталь: | TAPTITE CUP B M3X10 |
| Парткод: | 87311016 |
| Деталь: | SX CHUTE, DCP8080DN/ MFC8480DN |
| Парткод: | LF9850001 |
| Деталь: | LF4 FILM |
| Парткод: | LP2347001 |
| Деталь: | SCREW PAN (S/ P WASHER) M3X6 |
| Парткод: | 0A4300606 |
| Деталь: | LF ROLLER2 ASSY |
| Парткод: | LS0761001 |
| Деталь: | ACTUATOR R |
| Парткод: | LF9671001 |
| Деталь: | ACTUATOR SB, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LF9742001 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | LG2239001 |
| Деталь: | PHOTO INTERRUPTER, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LG2239001 |
| Деталь: | ACTUATOR FRONT1 |
| Парткод: | LF9683001 |
| Деталь: | ACTUATOR FRONT2, DCP8085DN/ MFC8680DN/ MFC8690DW/ MFC8880DN/ MFC8881DNHY/ MFC8890DW |
| Парткод: | LF9748001 |
| Деталь: | SEPARATION SPRING |
| Парткод: | LF9684001 |
| Деталь: | RUBBER HOLDER |
| Парткод: | LF9685001 |
| Деталь: | SEPARATION RUBBER |
| Парткод: | LF9686001 |
| Цена: | 700 ₽ |
| Деталь: | SPRING PLATE ADF FRONT A ASSY |
| Парткод: | LE1513001 |
| Деталь: | ADF FILM |
| Парткод: | LE2470001 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | LP2159001 |
| Деталь: | LF SPRING |
| Парткод: | LE2472001 |
| Деталь: | BACK SHEET ADF |
| Парткод: | LP2907001 |
| Деталь: | PANEL UNIT, MFC9840CDW |
| Парткод: | LU8236001 |
| Цена: | 16 100 ₽ |
| Деталь: | Тефлоновый вал |
| Парткод: | CET3553 |
| Цена: | 950 ₽ |
| Деталь: | Прижимной вал |
| Парткод: | CET6384 |
| Цена: | 1 600 ₽ |
| Деталь: | Тефлоновый вал |
| Парткод: | 51157 |
| Цена: | 1 600 ₽ |
| Деталь: | ALFB UNIT ASSY(SP) |
| Парткод: | LP2357001 |
| Деталь: | TAPTITE, CUP B M4X20 |
| Парткод: | 87412016 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | LG2239001 |
| Деталь: | FFC CABLE ASSY |
| Парткод: | LF9629001 |
| Деталь: | SCANNING MOTOR FB |
| Парткод: | LE8632001 |
| Деталь: | PULLEY ASSY |
| Парткод: | LF9637001 |
| Деталь: | PULLEY SPRING |
| Парткод: | LE8640001 |
| Деталь: | CCD MODULE(SP) |
| Парткод: | LF2037001 |
| Деталь: | BELT |
| Парткод: | LE8642001 |
| Деталь: | TOP COVER ASSY |
| Парткод: | LF9641001 |
| Деталь: | TAPTITE, CUP B M4X12 |
| Парткод: | 87411216 |
| Деталь: | TAPTITE, PAN B M3X8 |
| Парткод: | LE2861001 |
| Деталь: | SCREW, PAN (S/P WASHER) M3X6 |
| Парткод: | 0A4300606 |
| Деталь: | TAPTITE, B 3X6 |
| Парткод: | UF5034001 |
| Деталь: | LOCK LEVER ASSY |
| Парткод: | LF2004001 |
| Деталь: | LOCK LEVER B |
| Парткод: | LE8649001 |
| Деталь: | TONER LED PCB ASSY |
| Парткод: | LV0282001 |
| Деталь: | LED HOLDER |
| Парткод: | LM4267001 |
| Деталь: | RUBBER FOOT |
| Парткод: | LJ7403001 |
| Деталь: | FILTER ASSY |
| Парткод: | LU7141001 |
| Деталь: | FAN MOTOR 60 UNIT LV |
| Парткод: | LM5114001 |
| Деталь: | FAN MOTOR 60 UNIT |
| Парткод: | LU7032001 |
| Деталь: | AIR DUCT ASSY AL |
| Парткод: | LM6655001 |
| Деталь: | WIRELESS PCB, MFC8690DW/MFC8890DW |
| Парткод: | LT0963001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LU7198001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LU7203001 |
| Цена: | 6 600 ₽ |
| Деталь: | Main PCB Assembly |
| Парткод: | LM5237001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LM5239001 |
| Деталь: | Main PCB Assembly |
| Парткод: | LM5245001 |
| Цена: | 80 ₽ |
| Деталь: | Main PCB Assembly |
| Парткод: | LM5246001 |
| Цена: | 60 ₽ |
| Деталь: | Main PCB Assembly |
| Парткод: | LM5247001 |
| Цена: | 80 ₽ |
Коды ошибок
1E
1F
24
35
36
3B
3C
3D
3E
44
50
51
52
53
54
55
56
57
58
59
63
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
75
76
78
7A
7D
7F
80
83
84
85
86
88
89
8A
8B
8C
8D
99
9F
A1
A2
A3
A4
A5
A6
A7
A8
AD
AE
AF
B0
B1
B2
B7
B8
B9
BB
BD
BF
C0
C7
C8
C9
CA
CD
D1
DD
DE
E0
E1
E2
E6
EB
EC
ED
EE
EF
F8
F9
FF
Описание
| Error code: | 1E |
| Description: | Drum Cartridge Fuse Error - The machine could not blow the fuse. |
| Remedy: | 1. Verify the drum cartridge is set correctly. 2. Check the point of contacts between drum cartridge and Connect A PCB (P86). 3. Check the contact between Connect A PCB (P80C) and the main board. 4. Replace the drum cartridge. 5. Replace the Connect A PCB. 6. Replace the main control PCB. |
| Error code: | 1F |
| Description: | Two or more optional trays are installed |
| Causes: | Connector: 54702-1219 failure. Main PCB failure |
| Remedy: | • Install one optional tray. (Only one optional tray is supported.). Replace the connector: 54702-1219. Replace the main PCB ASSY. |
| Error code: | 24 |
| Description: | A label format was sent to the printer but was not recognized. The DATA light does not flash. |
| Causes: | The communication parameters are incorrect. |
| Remedy: | Check the printer driver or software communications settings (if applicable). If you are using serial communication, check the serial port setting in the control panel menu. See Set Serial Communications on page 91. If you are using serial communication, make sure you are using a null modem cable or a null modem adapter. Using the control panel controls, check the protocol setting. It should be set to NONE. See Set Protocol on page 93. If a driver is used, check the driver communication settings for your connection. |
| Error code: | 35 |
| Description: | All lights are on, but nothing displays on the LCD, and the printer locks up. |
| Causes: | Internal electronic or firmware failure. |
| Remedy: | Turn the printer power off (O) and then on (I). If the printer locks up again, replace the main logic board. |
| Error code: | 36 |
| Description: | The printer locks up while running the Power-On Self Test. |
| Causes: | Main logic board failure. |
| Remedy: | Replace the main logic board. |
| Error code: | 3B |
| Display: | Unable to print 3B |
| Description: | Main PCB RAM failure |
| Causes: | Main PCB failure |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | 3C |
| Display: | Paper Jam |
| Description: | EEPROM writing error (Not applicable) |
| Error code: | 3D |
| Description: | EEPROM reading error (Not applicable) |
| Error code: | 3E |
| Display: | Unable to print 3E |
| Description: | EEPROM bus error (Not applicable) |
| Causes: | Main PCB failure |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | 44 |
| Display: | Send Error (DNS) |
| Description: | Fuser Sub Lamp Overheat Failure, Code 44 The front thermistor has detected an overheat condition. Note If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault is performed. |
| Causes: | • Fuser • Engine Control Board |
| Remedy: | 1 1. Turn OFF power, remove the fuser assembly and allow it to cool down. 2. Measure the resistance between the Fuser connector P600-7 and P600-9. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 2. Replace the fuser assembly. 2 1. Reinstall the fuser assembly. 2. Enter service diagnostics. 3. From the Sensor Tests run the Fuser Temperature test. 4. Is the temperature indicated approximately 165o C? Go to step 4. Go to step 3. 3 1. Turn OFF printer power. 2. Measure the resistance between J641-4 and J641-5 on the engine control board. 3. Does the resistance measure between 30 K and 190 K Ohms? Go to step 4. Repair or replace the wiring harness. 4 1. Turn printer power back ON. 2. Is there ~+3.4 VDC between J590-3 and ground? Check the AC wiring harness to the fuser. If the check is OK, replace the AC drive assembly. Replace the engine control board. |
| Error code: | 50 |
| Display: | Tray 2 Paper Empty |
| Description: | Fuser Fan Failure The Fuser Fan rotation signal indicates to the Engine Control Board that the fan is no longer operational. |
| Causes: | • Fuser Fan, PL5.3.31 • FAN/PHD/MOT Harness, PL10.1.9 • Engine Control Board, PL9.1.16 |
| Remedy: | 1 Check the Fuser Fan for damage. Remove the Front Cover. Is the fan damaged? Replace the Fuser Fan. Go to Step 2. 2 Check the Fuser Fan connection. Is P/J482 connected to the harness? Go to Step 2. Reconnect the Fan. 3 Check orientation of the Fuser Fan. Does the Fan’s label face into the chute? Go to Step 3. Correct the installation. 4 Test the Fuser Fan. Run the Service Diagnostics Fuser Fan test. Does the Fan operate. Go to Step 6. Go to Step 5. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J482. 2. Check continuity between J48 <=> P483. Go to Step 5. Replace the FAN/PHD/MOT Harness. 6 Check the fan rotation signal. Print one sheet. Is there +3.3 V across P/J48-A12 <=> P/J48-A13? Replace the Engine Control Board. Replace the Fuser Fan. |
| Error code: | 51 |
| Display: | Send Error (DNS) |
| Description: | Rear Fan Failure The Rear Fan rotation signal indicates the fan is no longer operational. |
| Causes: | • Rear Fan, PL1.1.19 • LVPS, PL9.1.6 • Engine Control Board, PL9.1.16 • LV Harness, PL10.1.2 |
| Remedy: | 1 Check the Rear Fan for damage. Remove the Rear Cover. Is the fan damaged? Replace the Rear Fan. Go to Step 2. 2 Check the Rear Fan connection. Is P/J166 connected to the harness? Go to Step 3. Connect the Fan. 3 Check orientation of the Rear Fan. Does the Fan’s label face inwards? Go to Step 4. Correct the installation. 4 Test the Rear Fan. Run the Service Diagnostics Rear Fan test. Does the fan operate? Go to Step 6. Go to Step 5. 5 Check for +24 V to the fan. Disconnect P/J166. Is there +24 V across P166-1 <=> P166-3? Replace the Rear Fan. Replace the LVPS. 6 Check the fan rotation signal to the LVPS. Print one sheet. Is there +3.3 V between P/J166-1 <=> P/J166-3? Replace the Fuser Fan. Go to Step 7. 7 Check the rotation signal from the LVPS. Print one sheet. Is there +3.3 V between P/J165-15 <=> P/J165-3? Replace the LVPS. Go to Step 8. 8 Check the fan rotation signal at the Engine Control Board. Print one sheet. Is there +3.3 V between P/J61-4 <=> P/J61-16? Replace the LV Harness Replace the Engine Control Board. |
| Error code: | 52 |
| Display: | Send Error (POP3) |
| Description: | Fan Failure One of the two fans has failed resulting in a fatal error. |
| Causes: | • Rear Fan, PL1.1.19 • Fuser Fan, PL5.3.31 |
| Remedy: | 1 Check the fans for damage or debris: • Fuser Fan, PL1.1.19 • Rear Fan, PL5.3.31 Is either fan damaged? Replace the defective fan. Go to Step 3. 2 Replace the defective fan. Does the error persist? Go to Step 3 Complete 3 Test the fans. Run the Service Diagnostics fan tests to isolate the defective fan. Did one of the fans fail? Go to the troubleshooting procedure for the specific fan. If both fans pass, replace the Engine Control Board. |
| Error code: | 53 |
| Display: | Send Error (SMTP) |
| Description: | The password did not match in a relay or mailbox transmission, and the transmission ended in failure. |
| Causes: | · Loose cable connection · Defective controller fan · Defective IOD1 board · Defective MCTL board |
| Remedy: | Confirm that both parties are using the same system password and the both units are compatible. Then, ask the remote party to transmit again. |
| Error code: | 54 |
| Display: | Send Error (Wrong Config) |
| Description: | 10-398 ERROR 54 FAN FAILURE |
| Causes: | · Loose cable connection · Defective ozone fan · Defective IOD2 board · Defective MCTL board |
| Remedy: | Enter Service Diagnostics Mode. Run the “Fuser Fan” test. Does the Fuser Fan operate? Y↓N→ Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-1 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-4 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-3 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the Fuser Fan. Replace the Fuser Fan Assembly. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-5 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-8 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-7 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the +24 VDC LVPS Fan. Replace the +24 VDC LVPS Fan. |
| Error code: | 55 |
| Display: | [Stop Pressed] |
| Description: | Stop/Clear has been pressed during a fax transmission. |
| Causes: | · Loose cable connection · Defective fusing unit fan · Defective IOD1 board · Defective MCTL board |
| Remedy: | Try again. |
| Error code: | 56 |
| Display: | Toner Empty |
| Description: | The toner cartridge has run out. The machine stops printing. |
| Causes: | Harness connection failure of back cover switch ASSY. Eject actuator failure. Eject sensor PCB ASSY failure. Main PCB failure |
| Remedy: | Replace the toner cartridge with a new one. |
| Error code: | 57 |
| Display: | Toner Low |
| Description: | The toner cartridge is almost empty. |
| Remedy: | Take out the toner cartridge and thoroughly shake it. By doing this, you can temporarily reestablish printing operations. |
| Error code: | 58 |
| Display: | Tray 1 Paper Empty |
| Description: | There is no paper in the tray 1. |
| Causes: | Harness connection failure between fuser unit and eject sensor PCB. Fuser unit failure. LVPS PCB failure. Eject sensor PCB ASSY failure. Main PCB failure |
| Remedy: | Load paper in the tray 1. |
| Error code: | 59 |
| Display: | Tray 2 Paper Empty |
| Description: | There is no paper in the optional tray 2. |
| Causes: | Harness connection failure between fuser unit and eject sensor PCB. Fuser unit failure. LVPS PCB failure. Eject sensor PCB ASSY failure. Main PCB failure |
| Remedy: | Load paper in the optional tray 2. |
| Error code: | 63 |
| Display: | Toner Exhausted |
| Description: | HOST_IF_NO_DRIVER:PCI |
| Causes: | Harness connection failure of new toner sensor harness ASSY. Harness connection failure of toner sensor PCB unit ASSY. New toner sensor harness ASSY failure (Toner empty). Toner sensor PCB unit ASSY failure. Main PCB failure. |
| Remedy: | You can select either stop or continue. It you do not select any, the printer will as stop is selected. If you select stop, you cannot print untill the genuine cartridge is installed. If you select continue, you can keep printing but the guality cannot be guaranteed, and the product svpport is no longer provided. If you wunt to change the selection, turn the printer off and on to gave this message apper again, and then re-select stop or continue. |
| Error code: | 67 |
| Display: | TOP BIN FULL |
| Description: | Orange light on The top bin is full of papers. Remove papers from the top bin. |
| Causes: | Toner sensor PCB ASSY failure. Main PCB failure |
| Remedy: | 1) Check the harness connected between the Engine controller and the exit board. (If the harness is out, insert it to the connector.) 2) In the Engine diagnostic mode, operate the full_R sensor to check if the sensor is operating. (If it is not operating, replace the exit board.) 3) Check the damage or warping of the sensor actuator. (If it is damaged or warped, replace the top bin full sensor.) 4) Replace the Engine controller. |
| Error code: | 68 |
| Display: | TOP FAN MOTOR LOCK ERROR |
| Description: | Orange light on An error has occurred at the top fan. |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1) Check the harness connected between the Engine controller and the exit board. (If the harness is out, insert it to the connector.) 2) Check the harness connected between the exit board and the top fan. (If the harness is out, insert it to the connector.) 3) In the Engine diagnostic mode, operate the top fan to check the fan is operating. (If it is not operating, replace the top fan.) 4) Check the No. 1 pin of the exit board whether 24V is outputted and check the D5 whether it is normal. (If 24V is not outputted or the part is abnormal, replace the exit board.) 5) Replace the Engine controller. |
| Error code: | 69 |
| Display: | Sleep Mode |
| Description: | Sleep Mode |
| Causes: | It means that the printer fuser is turned off, and the power consumption is minimized. |
| Remedy: | 1) Check the harness connected between the Engine controller and the paper size board. (If the harness is out, insert it to the connector.) 2) In the Engine diagnostic mode, operate the MPF trans sensor to check if it is operating. (If it is not operating, replace the paper size board.) 3) Replace the MPF transfer. |
| Error code: | 6A |
| Description: | Fuser unit failure (The side thermistor does not detect 60°C within the specified time.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6B |
| Description: | Fuser unit failure (The center thermistor does not detect 100°C within the specified time.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6C |
| Display: | Unable to Print 6C |
| Description: | Fuser unit failure (The center thermistor detects higher temperature than the specified value.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6D |
| Description: | Fuser unit failure (The center thermistor detects lower temperature than the specified value.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6E |
| Description: | Fuser unit failure (The center thermistor does not detect temperature rising within the specified time.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6F |
| Display: | Unable to Print 6F |
| Description: | Fuser unit failure (The center and side thermistors detect extremely high temperature.) |
| Causes: | Fuser unit harness connection failure. Fuser unit failure. LVPS PCB unit failure. Main PCB failure. |
| Remedy: | 1 Fuser unit harness connection failure Check the harness connection of the fuser unit and reconnect it. 2 Fuser unit failure Replace the fuser unit. 3 LVPS PCB unit failure Replace the LVPS PCB unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 70 |
| Display: | No Paper |
| Description: | No Paper |
| Causes: | No paper in the paper cassette. |
| Error code: | 71 |
| Display: | Paper Jam 0 |
| Description: | Paper Jam 0 |
| Causes: | The front part of paper is jammed between pickup unit and Feed sensor. |
| Error code: | 72 |
| Display: | Paper Jam 1 |
| Description: | Engine Firmware Failure The Engine Control Board detected a firmware error. |
| Causes: | • Engine Control Board, Pl9.1.16 • EEPROM Board, PL9.1.12 |
| Remedy: | 1 Cycle printer power. Does the error persist? Go to Step 2. Complete 2 Is P/J144 on the EEPROM Board properly seated and defect free? Go to Step 3. Reseat P/J144 or replace the EEPROM Board. 3 Turn printer power off and then back on. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 75 |
| Display: | [TRAY x] NOT INSTALLED |
| Description: | VIC Limutter |
| Causes: | · Loose cable connection · Defective fusing unit clutch · Defective IOD2 board · Defective MCTL board |
| Remedy: | 1) Check for any warping or damage to the cassette (In the case of warping or damage, replace the cassette) |
| Error code: | 76 |
| Display: | Out Bin Full |
| Description: | Fuser Firmware Failure A failure was detected in the Fuser Firmware. |
| Causes: | • Fuser, PL5.1.1 • FSR/ADC Harness, PL5.2.28 • Engine Control Board, PL9.1.16 |
| Remedy: | 1 Check the Fuser for damage. Is the Fuser damaged? Replace the Fuser. Go to Step 2. 2 Check the Fuser connection for damage. Any broken or bent pins? Repair or replace the parts. Go to Step 3. 3 Replace the Fuser. Does the error persist? Go to Step 4. Complete 4 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J361. 2. Check continuity between J36 <=> J361. Replace the Engine Control Board. Replace the FSR/ ADC Harness. |
| Error code: | 78 |
| Display: | WRONG PAPER SIZE [PAPER] IN [TRAY x] |
| Description: | Waste Cartridge Full Detection Sensor Failure, Code 78 |
| Causes: | • Waste Cartridge • Waste Cartridge Full Sensor • Engine Control Board |
| Remedy: | 1 1. Remove the waste cartridge sensor holder without disconnecting the harnesses. 2. Measure the voltage between the yellow wire on the waste cartridge full sensor and frame ground, alternately interrupting the sensor. 3. Does the voltage toggle between +5 and 0 VDC? Go to step 5. Go to step 2. 2 1. Measure the voltage between the gray wire and frame ground. 2. Does the voltage measure +5 VDC? Go to step 4. Go to step 3. 3 1. Remove the rear cover and rear shield. 2. Measure the voltage at J407B-17 on the engine control board. 3. Does the voltage measure +5 VDC? Inspect the wiring harness for damage and replace, if necessary. Replace the engine control board. 4 1. Measure the voltage between the violet wire and frame ground. 2. Does the voltage measure 0 VDC? Replace the waste cartridge full sensor. Inspect the wiring harness for damage and replace, if necessary. 5 1. Remove the rear cover and rear shield. 2. Measure the voltage at J407B-16 on the engine control board. 3. Alternately interrupt the sensor 4. Does the voltage toggle between +5 and 0 VDC? Replace the engine control board. Inspect the wiring harness for damage and replace, if necessary. |
| Error code: | 7A |
| Display: | Unable to clean 7A |
| Description: | No detection of the main motor lock signal. |
| Causes: | Main motor failure. Main PCB failure. |
| Remedy: | 1 Main motor failure Replace the main motor ASSY. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 7D |
| Display: | Unable to clean 7D |
| Description: | Dirt on drum unit |
| Causes: | Dirt or dust on drum unit electrodes. HVPS PCB failure. Main PCB failure. |
| Remedy: | 1 Dirt or dust on drum unit electrodes Clean the electrodes on the drum unit. ( p.271 "Electrodes location on the drum unit") 2 HVPS PCB failure Replace the HVPS PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 7F |
| Description: | Fax paper setting mismatch (The setting paper becomes besides the A4/Letter/Legal/Folio.) |
| Causes: | Main PCB failure |
| Remedy: | 1 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 80 |
| Display: | ERROR 80 FORMAT |
| Description: | Engine Logic Board Failure, Code 80 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete Replace the engine control board or the image processor board. |
| Error code: | 83 |
| Display: | h`******** |
| Description: | Engine Logic Board NVRAM Failure, Code 83 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace in the following order: • engine control board • image processor board |
| Error code: | 84 |
| Display: | h`******** |
| Description: | Controller to Engine Logic Board Time Failure, Code 84 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace the engine control board. |
| Error code: | 85 |
| Display: | ROM HASH |
| Description: | Engine Logic Board Micro Pitch Failure, Code 85 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace in the following order: • engine control board • image processor board |
| Error code: | 86 |
| Description: | High-Voltage Power Supply Failure, Code 86 |
| Remedy: | 1. Cycle power to the printer to clear the error. 2. Did this clear the error? Complete. Replace in the following order: • T3 HVPS • image processor board |
| Error code: | 88 |
| Display: | Paper Jam |
| Description: | Lower Tray Communication Failure, Code 88 |
| Causes: | • Engine Control Interface Board • Tray module board • Engine Control board |
| Remedy: | 1 Is J668-1 on the tray module board +5 VDC? Go to step 2. Use the wirenets to troubleshoot and repair the open wire. 2 Is J668-3 on the tray module board +24 VDC? Go to step 3. Use the wirenets to troubleshoot and repair the open wire. 3 1. Check the following connectors for continuity: • P669-1 to J534A-15 • P669-2 to J534A-14 • P669-3 to J534A-13 • P669-4 to J534A-12 • P669-5 to J534A-11 • P669-6 to J534A-10 2. Do all checks indicate continuity? Replace in the following order: • engine control interface board • tray module board • engine control board Check and repair broken wires or bad connectors. |
| Error code: | 89 |
| Display: | 89 |
| Description: | ITU Maintenance |
| Causes: | Registration rear sensor failure. Main PCB failure |
| Remedy: | Check the ITU Release Lever for correct operation. The ITU Release Lever is the black lever located on the left upper side frame above the ITU opening and can be seen by opening and lowering the MPF Assembly. When locked the lever should be at the 6 o`clock position. When unlocked it should be in a 3 o`clock position. Undue pressure is not required to operate the lever Turn the printer off, insert the ITU, move the lever to the 6 o`clock position, and turn the printer back on. If this does not resolve, replace the “ITU assembly”. Press Go to continue. The message persists until replacement. |
| Error code: | 8A |
| Display: | Paper Jam |
| Description: | Paper jam in Tray 1 (T1) (It is detects by the registration front sensor) |
| Causes: | Harness connection failure of registration front sensor PCB ASSY. Paper feed roller worn out. Registration front sensor PCB failure. Main PCB failure. |
| Remedy: | 1 Harness connection failure of registration front sensor PCB ASSY Check the harness connection of the registration front sensor PCB ASSY in the appropriate tray, and reconnect it. 2 Paper feed roller worn out Replace the paper feed roller. 3 Registration front sensor PCB failure Check the sensor performance following the procedure ( p.183 "Operational Check of Sensors (Function code 32)"). If any problem occurs, replace the registration front sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8B |
| Display: | Unable to Print 8B |
| Description: | Paper jam in Tray 2 |
| Causes: | Dirt on edge sensor. Harness connection failure of high voltage power supply PCB ASSY. Paper feeding kit worn out (MP/ Tray 1/ Tray 2). Registration front sensor failure. Main PCB failure |
| Remedy: | Clean the edge sensor. Check the harness connection of the high voltage power supply PCB ASSY in the appropriate tray, and reconnect it. Replace the paper feeding kit of the appropriate tray. Procedure described in "4.10 Sensor Operational Check (Function code 32)" in Chapter 6. If any problem occurs, replace the high voltage power supply PCB ASSY. Replace the main PCB ASSY. |
| Error code: | 8C |
| Display: | Paper Jam |
| Description: | Paper jam in MP Tray |
| Causes: | Dirt on edge sensor. Harness connection failure of high voltage power supply PCB ASSY. Paper feeding kit worn out (MP/ Tray 1/ Tray 2). Registration front sensor failure. Main PCB failure |
| Remedy: | Clean the edge sensor. Check the harness connection of the high voltage power supply PCB ASSY in the appropriate tray, and reconnect it. Replace the paper feeding kit of the appropriate tray. Procedure described in "4.10 Sensor Operational Check (Function code 32)" in Chapter 6. If any problem occurs, replace the high voltage power supply PCB ASSY. Replace the main PCB ASSY. |
| Error code: | 8D |
| Description: | Paper jam near paper eject tray (When power on, it is detects by the eject sensor.) |
| Causes: | Paper eject actuator not operating smoothly catching in some position. Eject sensor PCB ASSY failure. Main PCB failure. |
| Remedy: | 1 Paper eject actuator not operating smoothly catching in some position. Re-assemble the paper eject actuator. Ensure the paper eject sensor operates smoothly. 2 Eject sensor PCB ASSY failure Replace the eject sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 99 |
| Display: | VERSION DATA |
| Description: | Wrong version data. |
| Causes: | Main PCB failure |
| Error code: | 9F |
| Display: | Paper Jam |
| Description: | Paper empty (It is detects by the registration front sensor) |
| Causes: | Registration front actuator catching in some position. Registration front sensor PCB harness connection failure. Registration front sensor PCB failure. Main PCB failure. |
| Remedy: | 1 Registration front actuator catching in some position Re-assemble the registration front actuator. 2 Registration front sensor PCB harness connection failure Check the harness connection of the registration front sensor PCB and reconnect it. 3 Registration front sensor PCB failure Replace the registration front sensor PCB. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A1 |
| Display: | Cover is Open |
| Description: | Jam at Door A |
| Causes: | • Tray 1 (MPT) Feed Roller, PL10.1.53 • Tray 1 (MPT) Pick Roller, PL10.1.43 • Tray 1 (MPT) Retard Roller, PL10.1.16 • Registration Clutch #1, PL8.1.85 • Tray 2 Registration Motor, PL4.2.36 • Tray 2 Feed Motor, PL4.2.35 • Front Sensor Board, PL4.2.97 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Tray 1 (MPT) Feed Rollers • Registration Rollers • Sensor Actuator Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Registration #1 Sensor. Run the Service Diagnostics Registration Entrance Sensor test. Does the sensor operate correctly? Go to Step 3. Replace the actuator. If the error persists, replace the Front Sensor Board. 3 Test the Feed Motor, Registration Motor, and Registration Clutch #1. Do the components function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the harness for each motor and clutch. Are the wiring harnesses properly connected and free from defects? Replace the Engine Control Board. Replace the wiring harness and/or the problem motor/ clutch. |
| Error code: | A2 |
| Display: | DOCUMENT JAM |
| Description: | Jam at Door A |
| Causes: | • Duplex Unit, PL16.1.0 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Door A • Door D • Duplex Unit Rollers • Duplex Unit connector • Duplex Sensors and Actuators Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Duplex Unit sensors. Run the Service Diagnostics for each of the four Duplex Unit sensors. Do the sensors and actuators function correctly Go to Step 3. Replace the damaged sensor. 3 Test the Duplex Unit motors. Run the Service Diagnostics Duplex Motor tests. Do the motors function correctly Go to Step 4. Replace the Duplex Unit 4 Inspect the wiring harness for the Duplex Unit. Is the wiring harness properly connected and free from defects? Replace the Duplex Unit. Replace the Engine Control Board. |
| Error code: | A3 |
| Display: | DOCUMENT JAM |
| Description: | Jam at Door A Misfeed at Tray 1 (MPT) Media reached the Duplex Reverse Sensor, but a second sheet was detected entering the feed path from Tray 1 (MPT). This error represents a misfeed jam for media fed from Tray 1 (MPT). |
| Causes: | • Tray 1 (MPT) Feed Roller, PL10.1.53 • Tray 1 (MPT) Pick Roller, PL10.1.43 • Tray 2 Registration Motor, PL4.2.36 • Tray 2 Feed Motor, PL4.2.35 • Front Sensor Board, PL4.2.97 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Tray 1 (MPT) Feed Rollers • Registration Rollers • Sensor Actuator Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Registration #1 Sensor. Run the Service Diagnostics Registration Entrance Sensor test. Does the sensor operate correctly? Go to Step 3. Replace the actuator. If the error persists, replace the Front Sensor Board. 3 Test the Feed Motor, Registration Motor, and Registration Clutch #1. Do the components function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check each motor and clutch harness. Are the harnesses properly connected and free from defects? Replace the Engine Control Board. Replace the harness and/or problem motor/ clutch. |
| Error code: | A4 |
| Display: | Cover is Open |
| Description: | Sorter problem |
| Causes: | • Defective engine gate array • Defective fuse cut circuit on the engine board |
| Remedy: | Correct catching of the ADF cover open sensor. Replace the ADF cover. Replace the ADF cover open sensor. Replace the ADF relay PCB ASSY. Replace the main PCB ASSY. |
| Error code: | A5 |
| Display: | Unable to Scan A5 |
| Description: | ADF interlock |
| Causes: | Scanning failure. |
| Remedy: | 1 Scanning failure Turn the power switch off and on. Then, try scanning again. |
| Error code: | A6 |
| Display: | A6-Bypass Feeder Jam |
| Description: | Paper did not exit the Multi-sheet Bypass Feeder properly, causing a paper jam. Open Cover A and refer to the labels on the printer to clear the jam. |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the feeder. Also ensure the paper is loaded correctly in the feeder. 2. Clean the bypass feeder’s pick roller. 3. Test the main feed motor as described in “Motor and clutch tests”. Replace the main feed motor. 5. Replace the engine controller board. |
| Error code: | A7 |
| Display: | A7-Duplex Entry Jam |
| Description: | Paper did not enter the duplex module properly, causing a paper jam. Open Cover A and refer to the labels on the printer to clear the jam. |
| Causes: | Power supply fan error |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the currently used tray. Also ensure the paper is loaded correctly in the tray. 2. Clean the duplex unit’s rollers. 3. Test the duplex motor and clutch as described in “Motor and clutch tests”. Replace the duplex unit. 5. Replace the engine controller board. |
| Error code: | A8 |
| Display: | Unable to Scan A8 |
| Description: | ADF exit interlock |
| Causes: | Ozone fan error |
| Remedy: | Replace the CCD module. Replace the main PCB ASSY. |
| Error code: | AD |
| Description: | DMA transfer error |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY |
| Error code: | AE |
| Description: | IT home is not detected within 0.7 sec. during rotation of main motor. |
| Causes: | Position error of the intermediate transfer unit |
| Remedy: | Reconnect the home position sensor harness. Replace the drive PCB. Replace the belt. Replace the home position sensor. Replace the scanner motor. Replace the CCD module. Replace the main PCB ASSY. |
| Error code: | AF |
| Display: | Unable to Scan AF |
| Description: | FB unit home position failure |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | B0 |
| Description: | DIS (GI) could not detected. |
| Causes: | Scanner harness not connected correctly. Scanner harness broken. Main PCB failure |
| Remedy: | This may happen in some cases of bad line condition. Attempt the transmission again. |
| Error code: | B1 |
| Description: | Jam at Door B Misfeed at Tray 2 Media reached Feed-Out Sensor #2, but did not arrive at the Transfer Unit Entrance Sensor on time. This error represents a misfeed jam for media fed from Tray 2. |
| Causes: | • Feeder Assembly, PL4.2.0 • Registration Sensor #2, PL4.2.89 • Registration Clutch #2, PL4.2.87 • Tray 2 Registration Motor, PL4.2.36 • Tray 2 Feed Motor, PL4.2.35 • Feeder Board, PL4.2.97 |
| Remedy: | 1 Check the following for evidence of fault, dirt, debris, or damage: • Door B • Tray 2 Feed Rollers • Registration Rollers • Transport Rollers • Sensor Actuators Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Tray 2 sensors. Run the Service Diagnostics Tray 2 Switches test. Do the sensors function correctly? Go to Step 4. Go to Step 3. 3 Check the TRYSNS1 harness continuity. Is the harness conductive? Replace the sensor. If the error persists, replace the Feeder Board. Replace the harness. 4 Test the Tray 2 Feeder Motors. Run the Service Diagnostics Tray 2 Motor tests for the Feed and Registration Motors. Do the motors function correctly? Go to step 6. Go to Step 5. 5 Check the REGHOP harness continuity. Is the harness conductive? Replace the motor. If the error persists, Go to Step 8. Replace the harness. 6 Test the Registration Clutch #2 Run the Service Diagnostics Tray 2 Clutch test. Does the clutch function correctly? Go to step 10. Go to step 7. 7 Check the CL1 harness continuity. Is the harness conductive? Replace the clutch. If the error persists, go to Step 8. Replace the harness. 8 Check for +24 V to the Motor Driver Board. Disconnect POW24. Is there +24 V across POW24-1 and 2? Replace the Motor Driver Board. Go to Step 9. 9 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is there +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 10 Check the Registration Assembly for gaps between the rollers. Is there a gap between the Registration Rollers? Replace the Registration Assembly. Go to Step 11. 11 Check the DRV1 harness continuity. Is the harness conductive? Replace the Motor Driver Board. If the error persists, replace the Engine Control Board Replace the harness. |
| Error code: | B2 |
| Description: | DCN is received. |
| Causes: | • Defective gate array U204 on the engine board (KP-864). • Defective harness (S02400) between engine board and option unit interface connector. • Defective paper feeder PF-60. |
| Remedy: | This may happen in some cases of bad line condition. Attempt the transmission again. |
| Error code: | B7 |
| Description: | Detection error of scanner (Scanning reference voltage adjustment malfunction.) |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | B8 |
| Display: | B8-Duplex Jam |
| Description: | Paper did not enter the duplex module properly, causing a paper jam. Open Cover B and refer to the labels on the printer to clear the jam. |
| Causes: | Cyan developing unit movement error |
| Remedy: | 1. Ensure the correct weight and type of paper is loaded in the currently used tray. Also ensure the paper is loaded correctly in the tray. 2. Clean the duplex unit’s rollers. 3. Test the duplex motor and clutch as described in “Motor and clutch tests”. Replace the duplex unit. 5. Replace the engine controller board. |
| Error code: | B9 |
| Description: | Scanning light adjustment error is detected. |
| Causes: | FB unit failure. Main PCB failure |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BB |
| Description: | White level data error |
| Causes: | FB unit failure. Main PCB failure. |
| Remedy: | 1 FB unit failure Replace the FB unit. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BD |
| Display: | Unable to Scan BD |
| Description: | Engine EEPROM check error. Printing is continued. |
| Causes: | Engine EEPROM check error |
| Remedy: | Replace the CCD module. Replace the main PCB ASSY. |
| Error code: | BF |
| Display: | Unable to Scan BF |
| Description: | EEPROM (Fuser unit) check error |
| Causes: | EEPROM (Fuser unit) Error error |
| Remedy: | Correct smooth operation and that there is no catching of the document front actuator 2. Replace the document front sensor 2. |
| Error code: | C0 |
| Description: | Image signal carrier was not detected. |
| Causes: | • Defective gate array U204 on the engine board (KP-864). • Blown-out fuse (F202) on the engine board. • Improper installation between printer and option paper feeder. • Defective harness (S02400) between engine board and option unit interface connector. • Improper connector insertion. • Defective option paper feeder PF-60. |
| Remedy: | This may happen in some cases of bad line condition. Ask the remote party to transmit again. |
| Error code: | C7 |
| Display: | SVC C7 ERROR |
| Description: | Error C7 |
| Causes: | • If the Master removal 5 times. |
| Remedy: | 1. Check if any thermistor connector is disconnected. 2. Check if any harness of the thermistors (center/rear, upper/lower) is open-circuited. 3. Check the LGC board if the connector J122 is disconnected. 4. After completing the repair of what caused the [C7] problem, proceed to rewrite the status counter (08-700) to "0", following the same procedure as for [C41] to [C48] . |
| Error code: | C8 |
| Description: | Paper stays in tray or duplex or HCF |
| Causes: | • If the Ink sensor does not detect ink in the Squeegee unit within 20 seconds after the Inking motor was activated. • If the Ink sensor does not detect ink in the Squeegee unit within 40 seconds after the Inking motor was activated when the Ink bottle is installed just after replacing empty ink bottle. |
| Remedy: | Ink bottle set sensor OFF & 5 seconds later ON. |
| Error code: | C9 |
| Description: | Bypass jam |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | CA |
| Description: | Main board problem |
| Remedy: | Check the harness connection of the USB host relay PCB ASSY and reconnect it. Replace the USB host relay PCB ASSY. Replace the main PCB ASSY. |
| Error code: | CD |
| Description: | BC RAM hardware |
| Causes: | The CD error also suggests that the sorter ST-30 is defective. |
| Remedy: | Clean both electrodes. Replace the HVPS PCB unit. Replace the main PCB ASSY. |
| Error code: | D1 |
| Display: | SVC D1 ERROR |
| Description: | Jam at Door D Open Door D to Clear Media reached Duplex Reverse Sensor, but did not leave the Duplex Unit on time. This error represents a misfeed jam inside the Duplex Unit. |
| Causes: | • Duplex Unit, PL16.1.0 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Duplex Unit Entrance Roller • Duplex Unit Connector • Duplex Unit Is there any damage or debris? Replace any damaged parts. Go to Step 2. 2 Test the Duplex Entrance, Reverse, Front, and Rear actuators and sensors using Service Diagnostics. Do the sensors and actuators function correctly? Go to Step 3. Replace the Duplex Unit. 3 Test the Duplex Motors using Service Diagnostics. Do the motors function correctly? Go to Step 4. Replace the Duplex Unit. 4 Inspect the DUPLEX harness. If defective, replace the wiring harness. Is the harness properly seated and free from defects? Replace the Motor Driver Board. Replace the Duplex Unit. |
| Error code: | DD |
| Description: | Fuser error other than 58, 59, 68, 69, 6A, 6B, 6C, 6D, 6E, 6F, 76, 78, DE and E2 are occurred |
| Causes: | Fuser unit failure. Main PCB failure. LVPS PCB failure |
| Remedy: | Replace the fuser unit. Replace the main PCB ASSY. Replace the LVPS PCB ASSY. |
| Error code: | DE |
| Description: | Imaging Unit type mismatch |
| Causes: | Imaging Unit being used is not intended for use with the printer. |
| Remedy: | Reconnect the relay rear PCB ASSY connector correctly. Replace the fuser unit. Replace the main PCB ASSY. |
| Error code: | E0 |
| Display: | SVC E0 ERROR |
| Description: | Machine has reset |
| Causes: | • Error with CPU and gate arrays of either the engine or main controller • Connection error between the engine board and the main controller board • Program overrun in the engine or main controllere |
| Remedy: | Remove the cause of the printer error, then ask the remote party to transmit again. |
| Error code: | E1 |
| Display: | SVC E1 ERROR |
| Description: | Jam at Door E Paper misfeed jam between the Fuser and the Top Output Tray. Media reached the Fuser Exit Sensor, but did not reach the Top Output Tray Stack Full Sensor on time. This error represents a misfeed jam inside the Exit Assembly. |
| Causes: | • Exit Assembly, PL11.1.0 • Fuser Motor, PL2.1.9 • Exit Gate Solenoid, PL11.1.17 • Full Stack Sensor, PL11.1.39 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Door E • Fuser • Exit Rollers and drive gears • Stack Full Actuator • Exit Assembly Is there any damage or debris? Replace any damaged parts. Go to Step 2. 2 Test the Fuser Exit and Top Output Tray Stack Full Sensors. Do the sensors function correctly? Go to Step 4. Replace the sensor. If the error persists, go to Step 3. 3 Check all pins on the SNS Harness for continuity. Is the harness conductive? Go to Step 4. Replace the SNS Harness. 4 Test the Fuser Motor. Run the Service Diagnostics Fuser Motor test. Does the motor function correctly? Go to Step 6. Replace the motor. If the error persists, go to Step 5. 5 Check for +24 V to the Fuser Motor. Disconnect DCHEAT on the Motor Driver Board. Is there +24 V across DCHEAT-3 <=> ground? Go to Step 6. Replace the Motor Driver Board. If the error persists, go to Step 6. 6 Test the Exit Gate Solenoid. Run the Service Diagnostics Exit Gate Solenoid test. Does the solenoid function correctly. Go to Step 8. Replace the solenoid. If the error persists, go to Step 7. 7 Check for +24 V to the solenoid. 1. Actuate the interlock switches. 2. Disconnect SOLENOID from the Rear Sensor Board. Is there +24 V across SOLENOID-1 <=> ground? Go to Step 8. Replace the Rear Sensor Board. 8 Check the DRV0 and DRV1 ribbon cables that connect the Motor Driver Board to the Engine Control Board. Are these cables connected and undamaged? Replace the Engine Control Board. Replace the harnesses. |
| Error code: | E2 |
| Display: | SVC E2 ERROR |
| Description: | Reset signal happened. Might read E-2 something else. |
| Error code: | E6 |
| Display: | SVC E6 ERROR |
| Description: | Right side interlock |
| Causes: | • If Position-A sensor cannot be detected (or keeps detecting) even though the Main motor encoder sensor signal is making the output after the Main motor is activated. |
| Remedy: | Confirm details of the error using the error code and correct the error. Then ask the remote party to transmit again. |
| Error code: | EB |
| Description: | The data reading error for E2PROM |
| Causes: | Main PCB failure |
| Remedy: | Replace the main PCB ASSY. |
| Error code: | EC |
| Display: | Unable to print EC |
| Description: | ADF jam |
| Causes: | Harness connection failure of fan motor. Fan motor failure. Main PCB failure. |
| Remedy: | 1 Harness connection failure of fan motor Check the harness connection of the fan motor, and reconnect it. 2 Fan motor failure Replace the fan motor. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | ED |
| Display: | Touchscreen Init. Failed |
| Description: | ADF jam |
| Causes: | . Data readout error on the flash ROM |
| Remedy: | Developer Motor Are the connectors connect with the Developer Motor properly? No Connect properly. Control PCB (PW10620) Enter the Service Mode and select the Manual Charging Test of the Function Checking Mode. (Refer to the page 8-24.) 1. Does the voltage between the CN106-4 (+) and CN106-6 (-) on the Control PCB (PW10620) change to about 6V to 0V when the Developer Motor rotates? 2. Is the voltage between CN211-4 (+) and CN211-1 (-) on the Control PCB (PW10620) about 24V during the Ready condition? No Replace the Control PCB (PW10620) with the new one. Developer Motor Motor Control PCB Replace the Developer Motor or the Motor Control PCB with the new one. |
| Error code: | EE |
| Display: | EE-Transfer Belt Unit Missing |
| Description: | The transfer belt is either missing or requires reseating to be recognized by the printer. Turn off the printer, make sure the transfer belt is properly installed and turn on the printer. |
| Causes: | LD Signal is detected for 1 seconds continuously while the Main Motor is rotating. |
| Remedy: | 1. Remove and re-install the transfer belt unit. 2. Clean the transfer belt unit’s contact on the front-left side of the engine chassis. Clean the corresponding contacts on the transfer belt unit. 3. Install a new transfer belt unit. 4. Replace the engine controller board. 5. Replace the printer unit chassis. |
| Error code: | EF |
| Display: | EF-Fuser Unit Missing |
| Description: | The fuser is either missing or requires reseating to be recognized by the printer. Turn off the printer, make sure the fuser is properly installed and turn on the printer. If the problem persists, install a new fuser. |
| Causes: | LVPS PCB failure. Main PCB failure |
| Remedy: | 1. Remove and reinstall the fuser. 2. install a new fuser. 3. Replace the low-voltage power supply. 4. Replace the engine controller board. |
| Error code: | F8 |
| Display: | Unable to Print F8 |
| Description: | No power to collator |
| Causes: | Battery harness connection failure. Battery exhausted. Main PCB failure. |
| Remedy: | 1 Battery harness connection failure Reconnect the battery harness. 2 Battery exhausted Replace the battery. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | F9 |
| Description: | Collator bin home switch |
| Causes: | Turn the power off, when the Maintenance mode 74 is in progress. |
| Remedy: | 1 Turn the power off, when the Maintenance mode 74 is in progress. Implement the Maintenance mode 74 again. |
| Error code: | FF |
| Description: | Excess current to USB HOST PCB error |
| Causes: | USB HOST PCB failure. Main PCB failure. |
| Remedy: | Replace the USB HOST PCB ASSY. Replace the main PCB ASSY. |
