Konica-Minolta bizhub 602
Рейтинг
Модули
FUSING DRIVE UNIT
1ST PAPER FEED
ADU 2
SHIELD BOX 3
ADF PAPER FEED TRAY
SHIELD BOX
CASSETTE TRAY
IR BOARD SECTION
CONTROL PANEL 2
CASSETTE ASSY
BOTTLE DRIVE SECTION
TONER SUPPLY SECTION
LEVEL CONVEYANCE SECTION 2
1ST PAPER FEED 2
LCC LENGTH CONVEYANCE SECTION 2
TRANSFER RAIL SECTION
MANUAL FEED TRAY UNIT 4
ADF SWITCH SECTION
1000-SHEET PAPER FEED SECTION 2
REVERSAL UNIT
ADF CONVEYANCE SECTION 4
ADF PAPER EXIT SECTION
REAR FAN SECTION
1000-SHEET PAPER FEED SECTION
ADF DRIVE SECTION 2
ERASE LAMP
MANUAL FEED TRAY UNIT
ADF CONVEYANCE SECTION 2
SCANNER SECTION 2
SHIELD BOX 2
Control panel
EXTERNAL PARTS 3
1500-SHEET PAPER FEED SECTION 2
CASSETTE RAIL
SCANNER SECTION
REVERSAL UNIT 2
PAPER EXIT SECTION
REAR FAN SECTION 2
CONTACT SECTION
EJECT DRIVE SECTION
ROTATION DETECTING SENSOR
PAPER EXIT CONVEYANCE SECTION
LEVEL CONVEYANCE SECTION
1500-SHEET TRAY
DOOR SAFE SWITCH
HIGH VOLTAGE UNIT
REGISTRATION SENSOR
1000-SHEET TRAY
2ND PAPER FEED 2
FUSING SECTION
MAIN DRIVE UNIT
MAIN FRAME
MANUAL FEED TRAY UNIT 3
PH UNIT
IR COVER
REAR ELECTRICAL SECTION
ADF EXTERNAL PARTS
SIZE DETECTING SECTION
EXTERNAL PARTS 2
OZONE DUCT
LCC CASSETTE RAIL
ADU
IR FRAME
CASSETTE ASSY 2
TONER RAIL
ADF CONVEYANCE SECTION 3
ADF PAPER FEED SECTION
EXTERNAL PARTS 4
TONER COLLECT SECTION
CCD UNIT, SCANNER DRIVE
EXTERNAL PARTS
LCC DRIVE
ADF DRIVE SECTION
MAIN POWER SUPPLY UNIT
PAPER EXIT CONVEYANCE SECTION 2
MANUAL FEED TRAY UNIT 2
IH POWER SUPPLY
1500-SHEET PAPER FEED SECTION
TRANSFER UNIT
2ND PAPER FEED
PAPER EXIT CONVEYANCE SECTION 3
I-U FRAME SECTION
Детали MANUAL FEED TRAY UNIT
| Деталь: | Brushless motor /30 |
| Парткод: | A0P0M11500 |
| Деталь: | Pressure Gear /4 40T |
| Парткод: | A0P0235900 |
| Деталь: | BUSHING |
| Парткод: | 9J06210100 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | FUSING DRIVE FRAME |
| Парткод: | A00JR7B911 |
| Деталь: | TENSION SPRING |
| Парткод: | 4004258201 |
| Деталь: | Gear 58/62T |
| Парткод: | A00J230600 |
| Деталь: | GEAR 30T |
| Парткод: | A00J230300 |
| Деталь: | Gear 52/30T |
| Парткод: | A00J230000 |
| Деталь: | BUSHING |
| Парткод: | 1200312109Old |
| Деталь: | BUSHING |
| Парткод: | A0P0232500 |
| Деталь: | Gear 33T |
| Парткод: | A00J230700Old |
| Деталь: | Gear 33T |
| Парткод: | A00J230711 |
| Деталь: | Paper exit Shaft /1 |
| Парткод: | A00J231801Old |
| Деталь: | Paper exit Shaft /1 |
| Парткод: | A00J231812 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J232400 |
| Деталь: | Gear 38/38T |
| Парткод: | A00J230100 |
| Деталь: | Paper exit Bearing /1 |
| Парткод: | A00J232100Old |
| Деталь: | Paper exit Bearing /1 |
| Парткод: | A00J232111 |
| Деталь: | Fusing Shaft /1 |
| Парткод: | A00J231200 |
| Деталь: | GEAR 18T |
| Парткод: | A00J230800 |
| Деталь: | Gear 23T |
| Парткод: | A00J230500 |
| Деталь: | PIN |
| Парткод: | 4036254901 |
| Деталь: | Fusing Shaft /2 |
| Парткод: | A00J231500 |
| Деталь: | GEAR 13T |
| Парткод: | A00J235800 |
| Деталь: | BUSHING |
| Парткод: | 4036252401 |
| Деталь: | Fusing Frame /2 |
| Парткод: | A00J231000 |
| Деталь: | GEAR 30T |
| Парткод: | A00J230400 |
| Деталь: | Fusing Frame /3 |
| Парткод: | A00J232011 |
| Деталь: | Fusing Knob /1 |
| Парткод: | A00J232200 |
| Деталь: | Gear 35/23T |
| Парткод: | A00J230200 |
| Деталь: | Pressure Shaft /1 |
| Парткод: | A00J235400 |
| Деталь: | Pressure Gear /2 34/63T |
| Парткод: | A0P0235601 |
| Деталь: | PRESSURE STAKE /2 |
| Парткод: | A00J235300 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Pressure Gear /1 18/75T |
| Парткод: | A0P0235500 |
| Деталь: | PRESSURE STAKE /1 |
| Парткод: | A00J235200 |
| Деталь: | Pressure Frame /1 |
| Парткод: | A00J235003 |
| Деталь: | MOTOR ASSY |
| Парткод: | A0P0R75100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4036225801 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4004224802 |
| Деталь: | BRACKET |
| Парткод: | 4036224102 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J138000 |
| Деталь: | Fusing Drive Assy |
| Парткод: | A0P0R73811 |
| Деталь: | HOLDER |
| Парткод: | A00J566000 |
| Деталь: | Pulling Spring /Middle |
| Парткод: | A00J566900 |
| Деталь: | Idler Shaft |
| Парткод: | A0P0566101 |
| Деталь: | ROLL |
| Парткод: | 4030312201 |
| Деталь: | Paper feed Frame |
| Парткод: | A00J560400 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | ACTUATOR |
| Парткод: | 4030301612 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | CLUTCH |
| Парткод: | A00J563500 |
| Деталь: | GEAR 30T |
| Парткод: | 4425301301 |
| Деталь: | GEAR 29T |
| Парткод: | 4030300801 |
| Деталь: | Paper feed Holder |
| Парткод: | A00J560100 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J560302 |
| Деталь: | BUSHING |
| Парткод: | 1065308601 |
| Деталь: | Shaft /P |
| Парткод: | A00J564000 |
| Деталь: | GEAR 32T |
| Парткод: | 4425301601 |
| Деталь: | SHAFT |
| Парткод: | 4040309701 |
| Деталь: | Paper feed Shaft |
| Парткод: | A0P0560200 |
| Деталь: | Release Lever |
| Парткод: | A00J567300 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J566801 |
| Деталь: | SHAFT |
| Парткод: | A00J566500 |
| Деталь: | CONVEYANCE DRIVE CLUTCH |
| Парткод: | 57AA82030 |
| Деталь: | GEAR 28T |
| Парткод: | A00J562400 |
| Деталь: | WASHER |
| Парткод: | A00J566300 |
| Деталь: | Timing belt 160L |
| Парткод: | A00J562800 |
| Деталь: | Gear 22/32T |
| Парткод: | A00J562300 |
| Деталь: | MOUNTING PLATE / PAPER FEED DRIVE |
| Парткод: | A00JR7AA00 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12200 |
| Деталь: | Gear 24/42T |
| Парткод: | A00J562200 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A00J562501 |
| Деталь: | FRAME / PAPER FEED 1 |
| Парткод: | A00JR7AB00 |
| Деталь: | Paper feed 1 assy |
| Парткод: | A0P0R72000 |
| Деталь: | Cover /Upper |
| Парткод: | A00J810201 |
| Деталь: | Guide Film |
| Парткод: | A00J816300 |
| Деталь: | ACTUATOR |
| Парткод: | A00J813200 |
| Деталь: | TORSION SPRING |
| Парткод: | 4657373401 |
| Деталь: | Contact /1 |
| Парткод: | A0P0816700 |
| Деталь: | Sensor Plate /Lower |
| Парткод: | A00J812000 |
| Деталь: | Actuator /Lower |
| Парткод: | A00J811900 |
| Деталь: | TORSION SPRING |
| Парткод: | 4657373501 |
| Деталь: | Cover /Lower |
| Парткод: | A00J810712 |
| Деталь: | ROLL |
| Парткод: | A00J814101 |
| Деталь: | SHAFT |
| Парткод: | A00J814411 |
| Деталь: | SCREW |
| Парткод: | 4036596601 |
| Деталь: | SPRING |
| Парткод: | A00J814500 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J816200 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Wiring Cover |
| Парткод: | A00J815400 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | GEAR 25T |
| Парткод: | A00J813800 |
| Деталь: | Pulley 33/25T |
| Парткод: | A00J813900 |
| Деталь: | Sensor Plate /Middle |
| Парткод: | A00J813300 |
| Деталь: | Belt 160L |
| Парткод: | A00J811100 |
| Деталь: | DRIVE FRAME / LOWER |
| Парткод: | A00JR7B000 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12100 |
| Деталь: | Protection Film |
| Парткод: | A0P0816600 |
| Деталь: | Cover /Rear |
| Парткод: | A00J810600 |
| Деталь: | LEVER |
| Парткод: | A00J816100 |
| Деталь: | HOOK |
| Парткод: | A00J815300 |
| Деталь: | ADU Wiring |
| Парткод: | A00JN11300 |
| Деталь: | DRIVE FRAME / UPPER |
| Парткод: | A00JR7B100 |
| Деталь: | TIMING BELT 134L |
| Парткод: | 4657374301 |
| Деталь: | Sensor Plate /Upper |
| Парткод: | A00J812600 |
| Деталь: | Contact /2 |
| Парткод: | A0P0816800 |
| Деталь: | Contact /3 |
| Парткод: | A0P0816900 |
| Деталь: | Contact /4 |
| Парткод: | A0P0817000 |
| Деталь: | RAIL |
| Парткод: | A0P0133301 |
| Деталь: | PWB assembly(PWB-PCI ASSY) |
| Парткод: | A0P0H02601 |
| Деталь: | RAIL |
| Парткод: | A0P0144501 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0147901 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0136611 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0149200 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A0P0144100 |
| Деталь: | BUSHING |
| Парткод: | A0P0144400 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0144300 |
| Деталь: | HDD |
| Парткод: | A0EDM72000 |
| Деталь: | CABLE |
| Парткод: | A0P0N15200 |
| Деталь: | CABLE |
| Парткод: | A0P0N15100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0144200 |
| Деталь: | CONTACT |
| Парткод: | A0P0159300 |
| Деталь: | CONTACT |
| Парткод: | A0P0159200 |
| Деталь: | FAN MOTOR |
| Парткод: | A0EDM10500 |
| Деталь: | COVER |
| Парткод: | A0P0144800 |
| Деталь: | COVER |
| Парткод: | A0P0132801 |
| Деталь: | RAIL |
| Парткод: | A0P0147700 |
| Деталь: | Plat |
| Парткод: | A0P0149300 |
| Деталь: | BRACKET |
| Парткод: | A0HT560200 |
| Деталь: | ADF Wiring |
| Парткод: | A0HTN10201 |
| Деталь: | Photoreflector |
| Парткод: | A108M50000 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | ACTUATOR |
| Парткод: | A01H560600 |
| Деталь: | Photoreflector |
| Парткод: | 9J07M50000 |
| Деталь: | TRAY |
| Парткод: | A01H560101 |
| Деталь: | BRACKET |
| Парткод: | 9J07303301 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | BUSHING |
| Парткод: | 4469346501 |
| Деталь: | LEVER |
| Парткод: | A01H561800 |
| Деталь: | GUIDE |
| Парткод: | 9J07303602 |
| Деталь: | CAM |
| Парткод: | 4641341702 |
| Деталь: | GUIDE |
| Парткод: | 9J07303701 |
| Деталь: | Gear 14/37T |
| Парткод: | 4641341401 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J07320601 |
| Деталь: | GEAR 30T |
| Парткод: | 4641343601 |
| Деталь: | GEAR 13/28T |
| Парткод: | 4641341501 |
| Деталь: | BRACKET |
| Парткод: | 9J07310603 |
| Деталь: | RESISTOR |
| Парткод: | V801300006 |
| Деталь: | STOPPER |
| Парткод: | 9J07310401 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J07560000 |
| Деталь: | COVER |
| Парткод: | A0HT560411 |
| Деталь: | GEAR 40T |
| Парткод: | 9J07310502 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0HT562000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0HT562100 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 9J07680701 |
| Деталь: | PLATE SPRING |
| Парткод: | A01H561100 |
| Деталь: | GUIDE |
| Парткод: | A01H561200 |
| Деталь: | RACK |
| Парткод: | 9J07310313 |
| Деталь: | LIFTING PLATE |
| Парткод: | A01H560713 |
| Деталь: | SEAL |
| Парткод: | 4641350301 |
| Деталь: | REGULATING PLATE |
| Парткод: | A01H560502 |
| Деталь: | LABEL MAX |
| Парткод: | 9J07940100 |
| Деталь: | REGULATING PLATE |
| Парткод: | A01H560402 |
| Деталь: | Lifting Motor assy |
| Парткод: | A0HTR70500 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0130414 |
| Деталь: | Insulating sheet |
| Парткод: | A00J211300 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J141000 |
| Деталь: | FILTER |
| Парткод: | A0P0147600 |
| Деталь: | COVER |
| Парткод: | A0P0149600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J139400 |
| Деталь: | SHAFT |
| Парткод: | A00J140600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J133101 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4004685401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J133500 |
| Деталь: | COVER |
| Парткод: | A0P0149700 |
| Деталь: | COVER |
| Парткод: | A0P0148300 |
| Деталь: | Cover /ASSY |
| Парткод: | A0P0132901 |
| Деталь: | PWB Assembly (PWB-MC ASSY) |
| Парткод: | A2WUH00101 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0133600 |
| Деталь: | PLATE SPRING |
| Парткод: | A0P0138811 |
| Деталь: | GROUND PLATE |
| Парткод: | A0P0146400 |
| Деталь: | SCREW |
| Парткод: | 4036596601 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J03M10000 |
| Деталь: | DUCT |
| Парткод: | A00J156102 |
| Деталь: | PULLEY GUIDE PART |
| Парткод: | 56QA58420 |
| Деталь: | LABEL |
| Парткод: | A00J941700 |
| Деталь: | PFU Relay harness /8 |
| Парткод: | A00JN11N01 |
| Деталь: | WIRE PULLEY |
| Парткод: | 57AA17010 |
| Деталь: | LCT GUIDE PLATE RIGHT |
| Парткод: | 56QA58060D |
| Деталь: | WIRE HOLDER A |
| Парткод: | 55VA40610 |
| Деталь: | PAPER REGULATING CLAW |
| Парткод: | 540047200 |
| Деталь: | Protection Cover |
| Парткод: | 56QA58450 |
| Деталь: | LCT ADJUSTMENT SIDE PLATE |
| Парткод: | 56QA58050D |
| Деталь: | SUPPORT BOARD / WIRE PULLEY |
| Парткод: | A00JR7AN00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J613101 |
| Деталь: | PAPER GUIDE LABEL |
| Парткод: | 57AA97870 |
| Деталь: | SHAFT HOLDING PART |
| Парткод: | 56QA58070D |
| Деталь: | REAR REINFORCE PLATE |
| Парткод: | 56QA58490D |
| Деталь: | PAPER GUIDE SHAFT RIGHT |
| Парткод: | 56QA58150 |
| Деталь: | LABEL |
| Парткод: | A00J941600 |
| Деталь: | LCT GUIDE PLATE LEFT |
| Парткод: | 56QA59060D |
| Деталь: | PAPER GUIDE SHAFT LEFT |
| Парткод: | 56QA59150D |
| Деталь: | Reinforce Plate /Rear |
| Парткод: | A00J613900 |
| Деталь: | PWB Assembly(PWB-IF ASSY) |
| Парткод: | A0P0H01A01 |
| Деталь: | Inverter unit |
| Парткод: | A00JM41000 |
| Деталь: | SPACER |
| Парткод: | V502010033 |
| Деталь: | SPACER |
| Парткод: | V502010036 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0281100 |
| Деталь: | GUIDE PART |
| Парткод: | A00J281200 |
| Деталь: | GUIDE PART |
| Парткод: | A0P0281300 |
| Деталь: | PWB assembly(PWB-UCN ASSY) |
| Парткод: | A0P0H02500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0148000 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A0P0148101 |
| Деталь: | Mounting Plate /2 |
| Парткод: | A0P0148201 |
| Деталь: | 1st Slider Assy |
| Парткод: | A0P0R71100 |
| Деталь: | PWB Assembly(PWB-ID ASSY) |
| Парткод: | A0P0H01B00 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313150021 |
| Деталь: | Scanner Wiring /1 |
| Парткод: | A0P0N14100 |
| Деталь: | Scanner Wiring /2 |
| Парткод: | A0P0N14200 |
| Деталь: | CABLE |
| Парткод: | A0P0N15300 |
| Деталь: | TAPE |
| Парткод: | A0P0264800 |
| Деталь: | COVER |
| Парткод: | A0P0167902 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0191500 |
| Деталь: | WASHER |
| Парткод: | A00J192900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0191101 |
| Деталь: | WASHER |
| Парткод: | A00J191900 |
| Деталь: | ARM |
| Парткод: | A0P0191400 |
| Деталь: | LEVER |
| Парткод: | A0P0192200 |
| Деталь: | HANDLE |
| Парткод: | A0P0192500 |
| Деталь: | Read Cover /Front |
| Парткод: | A0P0167400 |
| Деталь: | LABEL |
| Парткод: | A0ED946500 |
| Деталь: | Operation panel mounting assy |
| Парткод: | A0P0R70600 |
| Деталь: | Label Emperon |
| Парткод: | A011946200 |
| Деталь: | Read Cover /2 |
| Парткод: | A0P0169700 |
| Деталь: | Read Cover /1 |
| Парткод: | A0P0167500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0192100 |
| Деталь: | LEVER |
| Парткод: | A0P0192300 |
| Деталь: | Pulling Spring |
| Парткод: | A00J192601 |
| Деталь: | Support Screw |
| Парткод: | A00J191800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0191200 |
| Деталь: | COVER |
| Парткод: | A0P0167700 |
| Деталь: | COLLAR |
| Парткод: | A00J191700 |
| Деталь: | ARM |
| Парткод: | A0P0191300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0191600 |
| Деталь: | COVER |
| Парткод: | A0P0168000 |
| Деталь: | Support Shaft |
| Парткод: | A00J192800 |
| Деталь: | FRAME |
| Парткод: | A0P0263201 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030321402 |
| Деталь: | GUIDE |
| Парткод: | 4030321501 |
| Деталь: | GEAR 14T |
| Парткод: | 4658301201 |
| Деталь: | GUIDE |
| Парткод: | 4537331701 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4498382501 |
| Деталь: | Regulating Plate /ASSY |
| Парткод: | A00J621102 |
| Деталь: | KNOB |
| Парткод: | 4037320401 |
| Деталь: | LEVER |
| Парткод: | 4128382301 |
| Деталь: | SHAFT |
| Парткод: | 4498382601 |
| Деталь: | LABEL |
| Парткод: | A00J942401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J621902 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J622004 |
| Деталь: | LIFTING PLATE |
| Парткод: | A0P0621500 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J623400 |
| Деталь: | FRICTION SHEET |
| Парткод: | 4030322601 |
| Деталь: | Guide Cushion |
| Парткод: | A00J623600 |
| Деталь: | Auxiliary Plate |
| Парткод: | A00J623500 |
| Деталь: | Lock Shaft |
| Парткод: | A00J622200 |
| Деталь: | LEVER |
| Парткод: | A0P0623700 |
| Деталь: | Lifting Shaft |
| Парткод: | A0P0621600 |
| Деталь: | LEVER |
| Парткод: | 4030320601 |
| Деталь: | Regulating Plate /ASSY |
| Парткод: | A00J621203 |
| Деталь: | LABEL CARRYING CAPACITY |
| Парткод: | 4002730601 |
| Деталь: | CASSETTE |
| Парткод: | A0P0A62015 |
| Деталь: | Drive Gear /3 40T |
| Парткод: | A00J403100 |
| Деталь: | Drive Gear /2 75/40T |
| Парткод: | A00J403000 |
| Деталь: | Drive Holder /Right |
| Парткод: | A00J402600 |
| Деталь: | Drive Gear /1 70/35T |
| Парткод: | A00J402900 |
| Деталь: | GEAR 40T |
| Парткод: | A00J404000 |
| Деталь: | SPRING |
| Парткод: | 4038541101 |
| Деталь: | COUPLING |
| Парткод: | A00J404102 |
| Деталь: | GUIDE |
| Парткод: | 4038541301 |
| Деталь: | COLLAR |
| Парткод: | 4038540701 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4038541202 |
| Деталь: | Fixing Plate /Right |
| Парткод: | A00J402801 |
| Деталь: | MOTOR |
| Парткод: | 9314130021 |
| Деталь: | GEAR 40T |
| Парткод: | A00J403700 |
| Деталь: | Drive Wiring /1 |
| Парткод: | A2WUN10900 |
| Деталь: | BOTTLE DRIVE-C BK |
| Парткод: | A00JR71311 |
| Деталь: | COVER |
| Парткод: | A0P0406700 |
| Деталь: | Agitating Shaft |
| Парткод: | A00J400611 |
| Деталь: | AGITAING PANEL |
| Парткод: | A00JR74400 |
| Деталь: | Bushing /B |
| Парткод: | 65AA32501 |
| Деталь: | SEAL |
| Парткод: | A00J402300 |
| Деталь: | Supply Casing |
| Парткод: | A00J400112 |
| Деталь: | SEAL |
| Парткод: | 4036534903 |
| Деталь: | TENSION SPRING |
| Парткод: | 4036534801 |
| Деталь: | SHUTTER |
| Парткод: | 4036534702 |
| Деталь: | Cover /Lower |
| Парткод: | A00J405400 |
| Деталь: | Toner Drive harness |
| Парткод: | A2WUN12300 |
| Деталь: | Gear 45T |
| Парткод: | A00J401700 |
| Деталь: | Gear 38/35T |
| Парткод: | A00J401800 |
| Деталь: | Drive Panel /H |
| Парткод: | A00J401501 |
| Деталь: | Stepping motor |
| Парткод: | A00JM12100 |
| Деталь: | DRIVEPANEL/H |
| Парткод: | A00JR7A100 |
| Деталь: | Gear 17/44T |
| Парткод: | A00J401900 |
| Деталь: | Seal /A |
| Парткод: | A00J402200 |
| Деталь: | GEAR 22T |
| Парткод: | A00J401600 |
| Деталь: | Supply Roller |
| Парткод: | A00J400500 |
| Деталь: | SEAL |
| Парткод: | A00J407300 |
| Деталь: | Spring /A |
| Парткод: | A00J401401 |
| Деталь: | Cover /Upper |
| Парткод: | A00J400300 |
| Деталь: | Regulating Claw |
| Парткод: | A00J401200 |
| Деталь: | Shutter /H |
| Парткод: | A00J400401 |
| Деталь: | Receiving Block /Left |
| Парткод: | A00J406801 |
| Деталь: | Receiving Block /Right |
| Парткод: | A00J406901 |
| Деталь: | Guide Cover /Left |
| Парткод: | A00J405600 |
| Деталь: | Seal /S |
| Парткод: | A00J400900 |
| Деталь: | Guide Cover /Right |
| Парткод: | A00J405500 |
| Деталь: | LEVEL DETECTION SENSOR |
| Парткод: | 40AA88031 |
| Деталь: | Panel /P |
| Парткод: | A00J406600 |
| Деталь: | SEAL |
| Парткод: | A00J405200 |
| Деталь: | SEAL |
| Парткод: | A0P0401000 |
| Деталь: | Mounting Plate /T |
| Парткод: | A0P0402500 |
| Деталь: | Sub Hopper Assy |
| Парткод: | A2WUR70200 |
| Деталь: | Mounting Plate /A |
| Парткод: | A00J614002 |
| Деталь: | Support Shaft /B |
| Парткод: | A00J614501 |
| Деталь: | Swing Shaft /B |
| Парткод: | A00J614700 |
| Деталь: | Sensor Block |
| Парткод: | A00J614300 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | PAPER DETECTION ACTUATOR |
| Парткод: | 56QA57240 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 56QA57170 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J614800 |
| Деталь: | Swing Panel /B |
| Парткод: | A00J614200 |
| Деталь: | SCREW |
| Парткод: | 4036596601 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0606400 |
| Деталь: | Idler Shaft |
| Парткод: | A00J606500 |
| Деталь: | ROLL |
| Парткод: | 4030312201 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J606600 |
| Деталь: | Conveyance Cover |
| Парткод: | A0P0606200 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J606100 |
| Деталь: | SUPPORT BLOCK |
| Парткод: | 56QA57110 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J606802 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J606900 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J606700 |
| Деталь: | LOCK SPRING |
| Парткод: | A00J660200 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A00J607301 |
| Деталь: | Light blocking Sheet |
| Парткод: | A0P0663400 |
| Деталь: | Shaft /L |
| Парткод: | A00J622600 |
| Деталь: | SHAFT |
| Парткод: | A00J623300 |
| Деталь: | ROLL |
| Парткод: | A00J663000 |
| Деталь: | TRAY PRESSING PLATE |
| Парткод: | 56AA41711 |
| Деталь: | Label LC2 |
| Парткод: | A00J941900 |
| Деталь: | GROUND PLATE |
| Парткод: | A00J607600 |
| Деталь: | GROUND PLATE |
| Парткод: | A00J607700 |
| Деталь: | Swing Panel /ASSY |
| Парткод: | A00J614101 |
| Деталь: | SWING SPRING REAR |
| Парткод: | 56QA57210 |
| Деталь: | Swing Shaft /A |
| Парткод: | A00J614600 |
| Деталь: | Support Shaft /A |
| Парткод: | A00J614400 |
| Деталь: | PFU Relay harness /6 |
| Парткод: | A00JN11F01 |
| Деталь: | REINFORCE PLATE /1 |
| Парткод: | A00J561900 |
| Деталь: | Photoreflector |
| Парткод: | A2WUR90000 |
| Деталь: | BRACKET |
| Парткод: | 4348304901 |
| Деталь: | Conveyance Roller /1 |
| Парткод: | A0P0570701 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | HOLDING GUIDE |
| Парткод: | A0P0567600 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J560502 |
| Деталь: | Paperfeed Relay harness /3 |
| Парткод: | A00JN11803 |
| Деталь: | GUIDE PART |
| Парткод: | A00J574301 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030312501 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J561300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J561200 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A0P0561700 |
| Деталь: | Mounting Plate /S |
| Парткод: | A00J564600 |
| Деталь: | SHAFT |
| Парткод: | 4030303901 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | Holder /S |
| Парткод: | A00J564700 |
| Деталь: | Guide Roller /Rear |
| Парткод: | A00J574800 |
| Деталь: | Fieldroller assy |
| Парткод: | A0P0R74000 |
| Деталь: | Release Lever |
| Парткод: | A0P0568100 |
| Деталь: | GUIDE PART |
| Парткод: | A00J567211 |
| Деталь: | Conveyance Gear /3 28T |
| Парткод: | A00J565400 |
| Деталь: | Conveyance Gear /2 21/31T |
| Парткод: | A00J565300 |
| Деталь: | GEAR 24T |
| Парткод: | A0P0570400 |
| Деталь: | Conveyance Belt 74L |
| Парткод: | A0P0568000 |
| Деталь: | Frame/Drive Moter |
| Парткод: | A0P0R7A100 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12500 |
| Деталь: | Drive Holder /1 |
| Парткод: | A00J563300 |
| Деталь: | Conveyance Gear /4 20/31T |
| Парткод: | A00J565500 |
| Деталь: | GEAR 22T |
| Парткод: | A00J574400 |
| Деталь: | Wiring Cover /1 |
| Парткод: | A00J563400 |
| Деталь: | Positioning Plate /Rear |
| Парткод: | A00J598700 |
| Деталь: | Fieldroller assy |
| Парткод: | A0P0R73911 |
| Деталь: | GUIDE PART |
| Парткод: | A00J609400 |
| Деталь: | Photoreflector |
| Парткод: | A2WUR90000 |
| Деталь: | SCREW |
| Парткод: | 4036596601 |
| Деталь: | Mounting Plate /F |
| Парткод: | A00J609501 |
| Деталь: | ROLLER |
| Парткод: | A00J572200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J609100 |
| Деталь: | BALL BEARING |
| Парткод: | A00J617900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J608700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J608800 |
| Деталь: | MOUNTING PLATE / UP/DOWN MOTOR |
| Парткод: | A00JR7AM00 |
| Деталь: | Heater Relay harness |
| Парткод: | A00JN10X00 |
| Деталь: | Heater Relay harness |
| Парткод: | A0P2N10X00 |
| Деталь: | Brush Motor |
| Парткод: | A0P0M10000 |
| Деталь: | Slide Shaft |
| Парткод: | 56AA17330 |
| Деталь: | TERMINAL ROCKING SPRING |
| Парткод: | 56AA17080 |
| Деталь: | Mounting Plate /Rear |
| Парткод: | A00J608900 |
| Деталь: | PFU Relay harness |
| Парткод: | A0P0N11G00 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J609000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J609300 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | CLUTCH ASSY |
| Парткод: | A00J609800 |
| Деталь: | PFU Relay harness /3 |
| Парткод: | A00JN11C01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J609201 |
| Деталь: | Protection Cover /S |
| Парткод: | A00J617000 |
| Деталь: | WASHER |
| Парткод: | A00J660700 |
| Деталь: | Holding Plate |
| Парткод: | A00J523312 |
| Деталь: | PLATE / REAR |
| Парткод: | A00JR7A200 |
| Деталь: | Cover /1 |
| Парткод: | A00J524101 |
| Деталь: | LOCK PLATE / REAR |
| Парткод: | A00JR7A300 |
| Деталь: | Connecting Plate |
| Парткод: | A00J523201 |
| Деталь: | Transfer Wiring |
| Парткод: | A00JN13C00 |
| Деталь: | Separating Wiring /E |
| Парткод: | A00JN13D00 |
| Деталь: | SLIDE PLATE / REAR |
| Парткод: | A00JR7BB00 |
| Деталь: | Cover /4 |
| Парткод: | A00J524402 |
| Деталь: | PIN |
| Парткод: | 4036231101 |
| Деталь: | Contact /Black |
| Парткод: | A00J520300 |
| Деталь: | Contact /Black |
| Парткод: | A00J522600 |
| Деталь: | Transfer Rail /Front |
| Парткод: | A00J520102 |
| Деталь: | Plate spring /1 |
| Парткод: | A00J521601 |
| Деталь: | LOCK PLATE / FRONT |
| Парткод: | A00JR7A500 |
| Деталь: | Holding Plate |
| Парткод: | A00J524001 |
| Деталь: | PLATE / FRONT |
| Парткод: | A00JR7A600 |
| Деталь: | Connecting Plate |
| Парткод: | A00J523901 |
| Деталь: | SLIDE PLATE / FRONT |
| Парткод: | A00JR7A700 |
| Деталь: | Plate spring /2 |
| Парткод: | A00J521701 |
| Деталь: | Transfer Rail /Rear |
| Парткод: | A00J520203 |
| Деталь: | CONTACT |
| Парткод: | A00J520800 |
| Деталь: | CONTACT |
| Парткод: | A00J520900 |
| Деталь: | SEPARATING WIRING/1 |
| Парткод: | A00JN13E00 |
| Деталь: | SEPARATING WIRING/2 |
| Парткод: | A00JN13F00 |
| Деталь: | Cover /3 |
| Парткод: | A00J524300 |
| Деталь: | Cover /2 |
| Парткод: | A00J524201 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A00JR90000 |
| Деталь: | Sensor Relay harness /8 |
| Парткод: | A2WUN10M00 |
| Деталь: | Bypass Cover /Rear |
| Парткод: | A00J598001 |
| Деталь: | MOTOR ASSY |
| Парткод: | A0P0R75200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J593400 |
| Деталь: | MOUNTING PLATE / BYPASS 1 |
| Парткод: | A00JR7AR00 |
| Деталь: | GEAR 22T |
| Парткод: | A00J591800 |
| Деталь: | SHUTTER |
| Парткод: | A0P0598300 |
| Деталь: | Guide Sheet |
| Парткод: | A00J587600 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4036141001 |
| Деталь: | Bypass Holder /Front |
| Парткод: | A0P0596500 |
| Деталь: | Guide Sheet |
| Парткод: | A0P0597400 |
| Деталь: | Guide Sheet |
| Парткод: | A00J589100 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J587701 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J591201Old |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J591205 |
| Деталь: | Pulling Spring |
| Парткод: | A00J587300 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | SHAFT |
| Парткод: | 4030303901 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J592001 |
| Деталь: | Mounting Plate /S |
| Парткод: | A00J591002 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J591100 |
| Деталь: | Holder /S |
| Парткод: | A00J590901 |
| Деталь: | GUIDE PART |
| Парткод: | A00J597511 |
| Деталь: | Fieldroller/1 assy |
| Парткод: | A0P0R74100 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030312501 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J591300 |
| Деталь: | SEAL |
| Парткод: | A00J585800 |
| Деталь: | Gear 14/24T |
| Парткод: | A00J593101 |
| Деталь: | Gear 14/50T |
| Парткод: | A00J593300 |
| Деталь: | Mounting Plate /Rear |
| Парткод: | A00J587901 |
| Деталь: | Paperfeed Relay harness /5 |
| Парткод: | A00JN11402 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0588100 |
| Деталь: | Support Shaft |
| Парткод: | A00J598600 |
| Деталь: | COVER |
| Парткод: | A0P0588700 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J595702 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12200 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J596300 |
| Деталь: | Wiring Holder |
| Парткод: | A00J586300 |
| Деталь: | MUUNTINGPLATE/BYPASS2 |
| Парткод: | A00JR7AS00 |
| Деталь: | Bypass field roller assy |
| Парткод: | A0P0R72900 |
| Деталь: | ROLLER |
| Парткод: | A0HT890201 |
| Деталь: | ROLLER |
| Парткод: | A0HT705011 |
| Деталь: | GUIDE |
| Парткод: | 9J07460101 |
| Деталь: | BUSHING |
| Парткод: | 4643321501 |
| Деталь: | BUSHING |
| Парткод: | 4131253701 |
| Деталь: | FLANGE |
| Парткод: | A0HT221400 |
| Деталь: | Pulley 20T |
| Парткод: | A0HT220800 |
| Деталь: | BALL BEARING |
| Парткод: | A00J617800 |
| Деталь: | Pulley 25T |
| Парткод: | A0HT220400 |
| Деталь: | BALL BEARING |
| Парткод: | A00J211200 |
| Деталь: | CUSHION |
| Парткод: | A0HT891200 |
| Деталь: | GUIDE |
| Парткод: | 9J07460202 |
| Деталь: | GUIDE |
| Парткод: | 9J07470301 |
| Деталь: | GUIDE |
| Парткод: | 9J07471201 |
| Деталь: | CUSHION |
| Парткод: | 9J07160500 |
| Деталь: | ROLLER |
| Парткод: | A0HT810600 |
| Деталь: | ROLL |
| Парткод: | 9J07810300 |
| Деталь: | ADF Wiring |
| Парткод: | A0HTN10700 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J07470901 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J07470801 |
| Деталь: | GUIDE |
| Парткод: | 9J07470701 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335191052 |
| Деталь: | SHAFT |
| Парткод: | 9J07400301 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 9J07810000 |
| Деталь: | BUSHING |
| Парткод: | 4658351602 |
| Деталь: | LEVER |
| Парткод: | 9J07460302 |
| Деталь: | TENSION SPRING |
| Парткод: | 9J07460501 |
| Деталь: | Pulley 24T |
| Парткод: | A0HT220111 |
| Деталь: | Pulley 29T |
| Парткод: | A0HT220200 |
| Деталь: | BRACKET |
| Парткод: | 9J07460802 |
| Деталь: | Plunger solenoid |
| Парткод: | A0HTM20000 |
| Деталь: | Timing belt 100L |
| Парткод: | A0HT221200 |
| Деталь: | Timing belt 118L |
| Парткод: | A0HT221300 |
| Деталь: | BRACKET |
| Парткод: | 9J07460701 |
| Деталь: | PULLEY 30T |
| Парткод: | A0HT220000 |
| Деталь: | LEVER |
| Парткод: | 9J07460401 |
| Деталь: | Conveyance Cover |
| Парткод: | A00J618700 |
| Деталь: | Pulling Spring |
| Парткод: | A00J604701 |
| Деталь: | Idler Roll |
| Парткод: | A00J605100 |
| Деталь: | Idler Shaft |
| Парткод: | A00J605200 |
| Деталь: | SPRING MOUNTING PLATE 1 |
| Парткод: | 56AA40430 |
| Деталь: | Pulling Spring |
| Парткод: | A00J604800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J601300 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J601501 |
| Деталь: | Guide Plate /2 |
| Парткод: | A00J618601 |
| Деталь: | SHAFT |
| Парткод: | A00J601700 |
| Деталь: | WASHER |
| Парткод: | A0P0664000 |
| Деталь: | Pulley 14T |
| Парткод: | A00J619611 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A00J618500 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | Pulley 15T |
| Парткод: | A00J619500 |
| Деталь: | Timing Belt 96L |
| Парткод: | A00J619800 |
| Деталь: | ROLL /1 |
| Парткод: | A00J619700 |
| Деталь: | ENTRANCE GUIDE SHEET |
| Парткод: | 56AA40540 |
| Деталь: | Multi-feed Adjusting Plate |
| Парткод: | A00J601600 |
| Деталь: | Input Shaft |
| Парткод: | A00J601402 |
| Деталь: | PAPER FEED INPUT SHAFT |
| Парткод: | 56QA40240D |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J603600 |
| Деталь: | Pressing Spring |
| Парткод: | 56AA40510 |
| Деталь: | PAPER FEED COUPLING PART |
| Парткод: | 56AA40450 |
| Деталь: | CLEANER SHAFT HOLDER |
| Парткод: | 56AA75050 |
| Деталь: | Gear 22/14T |
| Парткод: | A00J603400 |
| Деталь: | Gear43T |
| Парткод: | A00J600900 |
| Деталь: | Ground Plate /1 |
| Парткод: | A00J605600 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12400 |
| Деталь: | Mounting plate / Paper exit motor |
| Парткод: | A0P0R7A400 |
| Деталь: | Gear 16/26T |
| Парткод: | A00J891100 |
| Деталь: | Idler Gear 22T |
| Парткод: | A0P0891000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0896600 |
| Деталь: | GEAR 16T |
| Парткод: | A00J895100 |
| Деталь: | BUSHING |
| Парткод: | 4030309301 |
| Деталь: | PAPER EXIT ROLLER |
| Парткод: | A0P0890700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J896801 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J898001 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J898101 |
| Деталь: | CONTACT |
| Парткод: | A00J899101 |
| Деталь: | Guide Lever |
| Парткод: | A00J890501 |
| Деталь: | BUSHING |
| Парткод: | 4030382301 |
| Деталь: | Pulling Spring |
| Парткод: | A00J893800 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J896500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J891200 |
| Деталь: | COVER |
| Парткод: | A00J898200 |
| Деталь: | REVERSAL UPPER STAKE |
| Парткод: | A00JR7B500 |
| Деталь: | ROLL |
| Парткод: | 4004590301 |
| Деталь: | SHAFT |
| Парткод: | 4025598401 |
| Деталь: | SCREW |
| Парткод: | 4036596601 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0890200 |
| Деталь: | Guide Plate /Lower |
| Парткод: | A0P0890101 |
| Деталь: | Timing belt 86L |
| Парткод: | A0P0900600 |
| Деталь: | CUSHION |
| Парткод: | A0P0900800 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0P0900400 |
| Деталь: | Riverse unit |
| Парткод: | A0P0R73500 |
| Деталь: | SHAFT |
| Парткод: | 9J07450202 |
| Деталь: | ROLL |
| Парткод: | 9J07430201 |
| Деталь: | GUIDE |
| Парткод: | 9J07441201 |
| Деталь: | GUIDE |
| Парткод: | 9J07441101 |
| Деталь: | TENSION SPRING |
| Парткод: | 9J07441701 |
| Деталь: | BRACKET |
| Парткод: | 9J07441001 |
| Деталь: | GUIDE |
| Парткод: | 9J07441502 |
| Деталь: | TENSION SPRING |
| Парткод: | 9J07450501 |
| Деталь: | GUIDE |
| Парткод: | 9J07443501 |
| Деталь: | GUIDE |
| Парткод: | A0HT260500 |
| Деталь: | GUIDE |
| Парткод: | A07H260600 |
| Деталь: | GUIDE |
| Парткод: | A0HT260400 |
| Деталь: | HOLDER |
| Парткод: | 9J07443001 |
| Деталь: | ROLLER |
| Парткод: | 9J07470101 |
| Деталь: | BUSHING |
| Парткод: | 4131253701 |
| Деталь: | KNOB |
| Парткод: | A0HT220700 |
| Деталь: | PIN |
| Парткод: | 4131253602 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | LEVER |
| Парткод: | 9J07430801 |
| Деталь: | BUSHING |
| Парткод: | 1200312109 |
| Деталь: | ARM |
| Парткод: | 9J07430401 |
| Деталь: | STOPPER |
| Парткод: | 9J07431401 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 9J07444301 |
| Деталь: | BUSHING |
| Парткод: | 9J07444101 |
| Деталь: | PRESSURE SPRING |
| Парткод: | A07H260300 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07430501 |
| Деталь: | REINFORCE PLATE |
| Парткод: | 9J07431601 |
| Деталь: | PIN |
| Парткод: | 1067250301 |
| Деталь: | ROLLER |
| Парткод: | A0HT700400 |
| Деталь: | STOPPER |
| Парткод: | 9J07431501 |
| Деталь: | SHAFT |
| Парткод: | 9J07430301 |
| Деталь: | SHAFT |
| Парткод: | 9J07430701 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07430601 |
| Деталь: | ARM |
| Парткод: | 9J07431201 |
| Деталь: | PROTECTION |
| Парткод: | 1154467001 |
| Деталь: | BRACKET |
| Парткод: | 9J07442702 |
| Деталь: | PULLEY 32T |
| Парткод: | 9J07500901 |
| Деталь: | EARTH GROUND |
| Парткод: | A01H700500 |
| Деталь: | GUIDE |
| Парткод: | 9J07443601 |
| Деталь: | GUIDE |
| Парткод: | 9J07441301 |
| Деталь: | GUIDE ASSY |
| Парткод: | A07HR70500 |
| Деталь: | GUIDE |
| Парткод: | 9J07490401 |
| Деталь: | LEVER |
| Парткод: | 9J07491101 |
| Деталь: | LEVER |
| Парткод: | 9J07492102 |
| Деталь: | PAPER EXIT TRAY |
| Парткод: | A0HT890000 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07491201 |
| Деталь: | SHAFT |
| Парткод: | 9J07890000 |
| Деталь: | COLLAR |
| Парткод: | 9J08210401 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | BRACKET |
| Парткод: | A0HT891900 |
| Деталь: | Neutralizing Brush |
| Парткод: | A0HU705100 |
| Деталь: | GUIDE |
| Парткод: | A01H810500 |
| Деталь: | GUIDE |
| Парткод: | A01H810300 |
| Деталь: | CUSHION |
| Парткод: | A0HT891200 |
| Деталь: | GUIDE |
| Парткод: | A0HT706001 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07420402 |
| Деталь: | GUIDE |
| Парткод: | 9J07420602 |
| Деталь: | GUIDE |
| Парткод: | 9J07420301 |
| Деталь: | GUIDE |
| Парткод: | 9J07420204 |
| Деталь: | COVER |
| Парткод: | 9J07420801 |
| Деталь: | SEAL |
| Парткод: | A108713300 |
| Деталь: | GUIDE |
| Парткод: | 9J07420901 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07420502 |
| Деталь: | ADF Wiring |
| Парткод: | A0HTN10900 |
| Деталь: | GUIDE ASSY |
| Парткод: | A0HUR70200 |
| Деталь: | DUCT |
| Парткод: | A0P0150100 |
| Деталь: | SEAL |
| Парткод: | A0P0150400 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313100072 |
| Деталь: | SEALING PART |
| Парткод: | A0P0151100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0150200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J150600 |
| Деталь: | Duct /2 |
| Парткод: | A00J157200 |
| Деталь: | SEAL |
| Парткод: | A0P0157500 |
| Деталь: | Duct /1 |
| Парткод: | A00J157100 |
| Деталь: | Duct /3 |
| Парткод: | A00J157301 |
| Деталь: | Duct /4 |
| Парткод: | A00J157401 |
| Деталь: | Duct /5 |
| Парткод: | A00J157501 |
| Деталь: | DUCT |
| Парткод: | A0P0157700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J157901 |
| Деталь: | Duct /6 |
| Парткод: | A00J157600 |
| Деталь: | DUCT |
| Парткод: | A0P0150300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0150500 |
| Деталь: | FAN MOTOR |
| Парткод: | A0P0M14200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J151002 |
| Деталь: | SEAL |
| Парткод: | A0P 0157600 |
| Деталь: | COVER |
| Парткод: | A00J618101 |
| Деталь: | Paper feed Cover /1 |
| Парткод: | A00J601201 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Conveyance Roller |
| Парткод: | A00J605511 |
| Деталь: | BALL BEARING |
| Парткод: | A00J617800 |
| Деталь: | Guide Assy draw /1 |
| Парткод: | A00J600313 |
| Деталь: | Detection Actuator /2 |
| Парткод: | A00J603300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J603200 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J605000 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | Regulating Plate /Front |
| Парткод: | A00J600600 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | CLUTCH |
| Парткод: | A00J563500 |
| Деталь: | ACTUATOR |
| Парткод: | A00J604301 |
| Деталь: | WASHER |
| Парткод: | A0P0664000 |
| Деталь: | Pulley 14T |
| Парткод: | A00J602800 |
| Деталь: | Timing belt 102L |
| Парткод: | A00J602700 |
| Деталь: | Paper feed Base frame /2 |
| Парткод: | A00J600204 |
| Деталь: | SHAFT |
| Парткод: | A00J603000 |
| Деталь: | Slide Shaft Holder |
| Парткод: | A03U812800 |
| Деталь: | PAPER FEED DRIVING CLUTCH |
| Парткод: | 56AA82012 |
| Деталь: | SHAFT STOPPER |
| Парткод: | 55VA42120 |
| Деталь: | Paper feed Coupling /2 |
| Парткод: | A00J605300 |
| Деталь: | Pressing Spring |
| Парткод: | A00J605400 |
| Деталь: | WASHER |
| Парткод: | A00J660700 |
| Деталь: | BALL BEARING |
| Парткод: | A00J617900 |
| Деталь: | AUXILIARY PART |
| Парткод: | A00J603101 |
| Деталь: | HANDLE |
| Парткод: | A00J618300 |
| Деталь: | Auxiliary Part /2 |
| Парткод: | A00J619400 |
| Деталь: | PAPER FEED REGULATING BLOCK |
| Парткод: | 56AA40380 |
| Деталь: | PFU Relay harness /5 |
| Парткод: | A00JN11E01 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A00J600400 |
| Деталь: | Paper feed Shaft |
| Парткод: | A00J604200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0602600 |
| Деталь: | COUPLING |
| Парткод: | A00J600500 |
| Деталь: | Paper feed Shaft /1 |
| Парткод: | A00J600800 |
| Деталь: | PUNCH SPACER |
| Парткод: | 15AG50280 |
| Деталь: | Detection Actuator /1 |
| Парткод: | A00J600701 |
| Деталь: | Detection Actuator /1 |
| Парткод: | A00J615901 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J604401 |
| Деталь: | WASHER |
| Парткод: | A00J660800 |
| Деталь: | HOLDER |
| Парткод: | A0P0663300 |
| Деталь: | Sealing Magnet |
| Парткод: | A00J660900 |
| Деталь: | 1000-sheet paper feed assy |
| Парткод: | A0P0R72311 |
| Деталь: | ADF Wiring |
| Парткод: | A0HTN10502 |
| Деталь: | Paper Exit Motor assy |
| Парткод: | A0HTR70900 |
| Деталь: | PULLING COIL SPRING |
| Парткод: | A0HT221500 |
| Деталь: | ROLL |
| Парткод: | A0HT220900 |
| Деталь: | Timing belt 364L |
| Парткод: | A0HT220500 |
| Деталь: | Timing belt 150L |
| Парткод: | A0HT221100 |
| Деталь: | KNOB |
| Парткод: | A0HT220700 |
| Деталь: | FLANGE |
| Парткод: | A0HT221000 |
| Деталь: | GUIDE |
| Парткод: | 9J07201102 |
| Деталь: | COVER |
| Парткод: | A01H100700 |
| Деталь: | Read Drive Tension Plate |
| Парткод: | A0P0R7A700 |
| Деталь: | GUIDE |
| Парткод: | 9J07201002 |
| Деталь: | ROLLER |
| Парткод: | A0HT210200 |
| Деталь: | TENSION SPRING |
| Парткод: | 9J07510601 |
| Деталь: | FLANGE |
| Парткод: | A0HT210700 |
| Деталь: | Timing belt 219L |
| Парткод: | A0HT210100 |
| Деталь: | Pulley 40T |
| Парткод: | A0HT210500 |
| Деталь: | FLANGE |
| Парткод: | A0HT210600 |
| Деталь: | Read Motor assy |
| Парткод: | A0HTR70200 |
| Деталь: | GUIDE |
| Парткод: | A07H101000 |
| Деталь: | FERRITE CORE |
| Парткод: | 9326181051 |
| Деталь: | HOLDER |
| Парткод: | A0P0103901 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | ACTUATOR |
| Парткод: | A0P0107500 |
| Деталь: | SHAFT |
| Парткод: | A0P0103300 |
| Деталь: | WIRE HARNESS ASSY |
| Парткод: | 4004685401 |
| Деталь: | ACTUATOR |
| Парткод: | A0P0104001 |
| Деталь: | TORSION SPRING |
| Парткод: | A0P0103401 |
| Деталь: | Protection Sheet |
| Парткод: | A0P0125400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J104700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J145000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J145101 |
| Деталь: | LED ARRAY |
| Парткод: | A00JM30301 |
| Деталь: | Light blocking Part |
| Парткод: | A00J145200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J107001 |
| Деталь: | Guide Plate /Front |
| Парткод: | A00J102500 |
| Деталь: | Sensor Relay harness /2 |
| Парткод: | A0P0N12H00 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0P0102900 |
| Деталь: | SHEET |
| Парткод: | A00J107401 |
| Деталь: | RAIL /FRONT |
| Парткод: | A00K106601 |
| Деталь: | Mounting Plate /Front |
| Парткод: | A00K106802 |
| Деталь: | COVER |
| Парткод: | A00J137103 |
| Деталь: | Mounting Plate /Rear |
| Парткод: | A00K106902 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J107100 |
| Деталь: | Guide Plate /Rear |
| Парткод: | A0P0102600 |
| Деталь: | ERASER LAMP ASSY |
| Парткод: | A00JR73700 |
| Деталь: | RAIL /REAR |
| Парткод: | A00K106700 |
| Деталь: | Bypass Tray /3 |
| Парткод: | A0P0594200 |
| Деталь: | LABEL |
| Парткод: | A00J942500 |
| Деталь: | SHAFT |
| Парткод: | 1134304202 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J599100 |
| Деталь: | ACTUATOR |
| Парткод: | A00J585300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J597900 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J597700 |
| Деталь: | ACTUATOR |
| Парткод: | A00J597800 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J599000 |
| Деталь: | COLLAR |
| Парткод: | 1134304101 |
| Деталь: | Bypass Tray /4 |
| Парткод: | A0P0594300 |
| Деталь: | RESISTOR |
| Парткод: | V801300006 |
| Деталь: | GEAR 40T |
| Парткод: | A00J597201 |
| Деталь: | Rack /L |
| Парткод: | A00J597100 |
| Деталь: | GEAR 18T |
| Парткод: | A00J596900 |
| Деталь: | SEAL |
| Парткод: | A00J589800 |
| Деталь: | Paperfeed Relay Harness /6 |
| Парткод: | A00JN11501 |
| Деталь: | Sensor Plate |
| Парткод: | A00J593600 |
| Деталь: | Actuator /E |
| Парткод: | A00J593700 |
| Деталь: | Torsion Spring /E |
| Парткод: | A00J593800 |
| Деталь: | Bypass Tray /1 |
| Парткод: | A00J594002 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J586900 |
| Деталь: | LABEL |
| Парткод: | A00J942601 |
| Деталь: | HOLDER |
| Парткод: | A00J597600 |
| Деталь: | SCREW |
| Парткод: | 4036578501 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J597300 |
| Деталь: | Lifting Lever |
| Парткод: | A00J592500 |
| Деталь: | FRICTION PLATE |
| Парткод: | A0P0599600 |
| Деталь: | LIFTING PLATE |
| Парткод: | A00J594602 |
| Деталь: | Holding Plate |
| Парткод: | A00J599300 |
| Деталь: | HOLDER |
| Парткод: | A00J595100 |
| Деталь: | Rack /R |
| Парткод: | A00J597000 |
| Деталь: | COLLAR |
| Парткод: | 4036365901 |
| Деталь: | Bypass Tray /2 |
| Парткод: | A00J594101 |
| Деталь: | CLEANING PAD |
| Парткод: | 4131462304 |
| Деталь: | Regulating Plate /R |
| Парткод: | A00J594501 |
| Деталь: | Brake Part |
| Парткод: | A00J587200 |
| Деталь: | Regulating Plate /L |
| Парткод: | A00J594401 |
| Деталь: | SCALE METRIC |
| Парткод: | A00J942801 |
| Деталь: | SCALE INCH |
| Парткод: | A00J942901 |
| Деталь: | LABEL |
| Парткод: | A00J942700 |
| Деталь: | Manual Feed Tray Unit |
| Парткод: | A0P0R72411 |
| Деталь: | ROLLER |
| Парткод: | A108563900 |
| Деталь: | SHAFT |
| Парткод: | A0HT561202 |
| Деталь: | PIN |
| Парткод: | 1067250101 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A0HT561100 |
| Деталь: | Neutralizing Brush |
| Парткод: | A01H565100 |
| Деталь: | BRACKET |
| Парткод: | A01H565500 |
| Деталь: | HOLDER |
| Парткод: | 9J07340401 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07340501 |
| Деталь: | SHAFT |
| Парткод: | 9J07340801 |
| Деталь: | TORSION SPRING |
| Парткод: | A01H565400 |
| Деталь: | Neutralizing Brush |
| Парткод: | A07H750200 |
| Деталь: | GUIDE |
| Парткод: | 9J07401601 |
| Деталь: | GUIDE |
| Парткод: | 9J07401701 |
| Деталь: | Separator Pad Assy |
| Парткод: | A01HR70411 |
| Деталь: | GUIDE |
| Парткод: | 9J07401401 |
| Деталь: | BRACKET |
| Парткод: | A07H750112 |
| Деталь: | COLLAR |
| Парткод: | 9J08210401 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | ADF Wiring |
| Парткод: | A0HTN10800 |
| Деталь: | TORSION SPRING |
| Парткод: | 9J07400902 |
| Деталь: | LEVER |
| Парткод: | 9J07400801 |
| Деталь: | WASHER |
| Парткод: | 9J07160600 |
| Деталь: | SHAFT |
| Парткод: | 9J07401201 |
| Деталь: | BRACKET |
| Парткод: | A07H750312 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140071 |
| Деталь: | LABEL |
| Парткод: | A01H941200 |
| Деталь: | COVER |
| Парткод: | A0P0289200 |
| Деталь: | SCREW |
| Парткод: | A00J290700 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4036141001 |
| Деталь: | SEAL |
| Парткод: | A00J291100 |
| Деталь: | SPACER |
| Парткод: | A00J290300 |
| Деталь: | Spacer t0.2 |
| Парткод: | A00J290800 |
| Деталь: | Spacer t0.1 |
| Парткод: | A00J290900 |
| Деталь: | FLANGE |
| Парткод: | A00J290600 |
| Деталь: | Pulley 37T |
| Парткод: | A00J288800 |
| Деталь: | Pulley 37T |
| Парткод: | A00J288600 |
| Деталь: | BUSHING |
| Парткод: | 1200312109 |
| Деталь: | SHAFT |
| Парткод: | A00J288400 |
| Деталь: | SHEET ASSY |
| Парткод: | A00JR70700 |
| Деталь: | Pulley 26/34T |
| Парткод: | A00J288700 |
| Деталь: | Stepping motor |
| Парткод: | A00JM12B01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0289700 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037090301 |
| Деталь: | COVER |
| Парткод: | A00J288203 |
| Деталь: | Glass movement unit |
| Парткод: | A0P0R70900 |
| Деталь: | COVER |
| Парткод: | 4037224701 |
| Деталь: | GASKET |
| Парткод: | A0P0M90300 |
| Деталь: | SCREW |
| Парткод: | 4025228301 |
| Деталь: | COVER |
| Парткод: | A0P0147201 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0149100 |
| Деталь: | Ope.unit Cable |
| Парткод: | A0P0N15000 |
| Деталь: | INTERFACE CABLE |
| Парткод: | A0P0N14900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0147401 |
| Деталь: | COVER |
| Парткод: | A00J138700 |
| Деталь: | SCREW |
| Парткод: | A1UD134000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0144900 |
| Деталь: | GUIDE RAIL |
| Парткод: | A00J136700 |
| Деталь: | Control Relay harness /2 |
| Парткод: | A0P0N12F01 |
| Деталь: | PWB assembly (PWB-MFP ASSY) |
| Парткод: | A2WUH02001 |
| Деталь: | PWB assembly (PWB-MFP ASSY) |
| Парткод: | A2WVH02001 |
| Деталь: | MEMORY MODULES |
| Парткод: | V865300026 |
| Деталь: | RAIL |
| Парткод: | A0P0144701 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | COVER |
| Парткод: | A0P0133002 |
| Деталь: | CUSHION |
| Парткод: | 4004182902 |
| Деталь: | Controller Relay harness /1 |
| Парткод: | A0P0N12R00 |
| Деталь: | GROUND PLATE |
| Парткод: | A0P0145900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0147300 |
| Деталь: | FERRITECORE |
| Парткод: | A0P0M90000 |
| Деталь: | Pen |
| Парткод: | A0PD160200 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0M70503 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0M70603 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0M70703 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0M70802 |
| Деталь: | PANEL ASSEMBLY |
| Парткод: | A0P0M70902 |
| Деталь: | COVER PANEL LOWER |
| Парткод: | A0P0169400 |
| Деталь: | Cover /Inside |
| Парткод: | A0P0165400 |
| Деталь: | Cover /Right rear |
| Парткод: | A0P0162700 |
| Деталь: | Cover /Right rear |
| Парткод: | A00J162802 |
| Деталь: | COVER |
| Парткод: | A00J164201 |
| Деталь: | Cover /Right front |
| Парткод: | A00J162901 |
| Деталь: | Cover /Right |
| Парткод: | A0P0161300 |
| Деталь: | Cover /Left |
| Парткод: | A00J160605 |
| Деталь: | FILTER |
| Парткод: | A2WU156600 |
| Деталь: | Cover /Left rear |
| Парткод: | A00J161400 |
| Деталь: | Cover /Left front |
| Парткод: | A2WU160500 |
| Деталь: | Input Shaft |
| Парткод: | A00J601402 |
| Деталь: | Ground Plate /2 |
| Парткод: | A00J605700 |
| Деталь: | GEAR 18T |
| Парткод: | A00J601000 |
| Деталь: | MOUNTING PLATE / LCC FEED DRIVE |
| Парткод: | A00JR7AK00 |
| Деталь: | SPRING MOUNTING PLATE 1 |
| Парткод: | 56AA40430 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | SPRING MOUNTING PLATE 2 |
| Парткод: | 56AA40440 |
| Деталь: | Ground Plate /Middle |
| Парткод: | A00J618800 |
| Деталь: | Pulling Spring |
| Парткод: | A00J604701 |
| Деталь: | Idler Roll |
| Парткод: | A00J605100 |
| Деталь: | Pulling Spring |
| Парткод: | A00J604800 |
| Деталь: | Idler Shaft |
| Парткод: | A00J605200 |
| Деталь: | SHAFT |
| Парткод: | A00J601700 |
| Деталь: | WASHER |
| Парткод: | A0P0664000 |
| Деталь: | Pulley 14T |
| Парткод: | A00J619611 |
| Деталь: | TORQUE LIMITER |
| Парткод: | A00J618500 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | Pulley 15T |
| Парткод: | A00J619500 |
| Деталь: | Timing Belt 96L |
| Парткод: | A00J619800 |
| Деталь: | ROLL /1 |
| Парткод: | A00J619700 |
| Деталь: | Guide Washer |
| Парткод: | A0P0602100 |
| Деталь: | Multi-feed Adjusting Plate |
| Парткод: | A00J601600 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J601501 |
| Деталь: | Gear 22/14T |
| Парткод: | A00J603400 |
| Деталь: | CLEANER SHAFT HOLDER |
| Парткод: | 56AA75050 |
| Деталь: | Paper feed Plate |
| Парткод: | A00J604101 |
| Деталь: | PAPER FEED INPUT SHAFT |
| Парткод: | 56QA40240D |
| Деталь: | Pressing Spring |
| Парткод: | 56AA40510 |
| Деталь: | PAPER FEED COUPLING PART |
| Парткод: | 56AA40450 |
| Деталь: | Gear43T |
| Парткод: | A00J600900 |
| Деталь: | Slide Rail /A |
| Парткод: | A00J631202 |
| Деталь: | Mounting Plate /Front |
| Парткод: | A00J631600 |
| Деталь: | SCREW |
| Парткод: | A00J618400 |
| Деталь: | SCREW |
| Парткод: | 1151330001 |
| Деталь: | Holding Plate |
| Парткод: | A00J631800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J630102 |
| Деталь: | SCREW |
| Парткод: | A00J631700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J630800 |
| Деталь: | Manuscript glass assy |
| Парткод: | A0P0R71000 |
| Деталь: | Holding Plate spring |
| Парткод: | A00J273601 |
| Деталь: | MIRROR |
| Парткод: | A0P0273212 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0273400 |
| Деталь: | COVER |
| Парткод: | A00J274300 |
| Деталь: | SCREW |
| Парткод: | A00J274401 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J273501 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0273300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J274201 |
| Деталь: | PULLEY |
| Парткод: | A00J273900 |
| Деталь: | BUSHING |
| Парткод: | 4002148101 |
| Деталь: | BUSHING |
| Парткод: | 4002148002 |
| Деталь: | Holding Plate spring |
| Парткод: | A00J273701 |
| Деталь: | FRAME |
| Парткод: | A00J273103 |
| Деталь: | Holding Plate spring |
| Парткод: | A00J273801 |
| Деталь: | Holding Plate |
| Парткод: | A00J265100 |
| Деталь: | PULLEY |
| Парткод: | A00J274000 |
| Деталь: | GUIDE PART |
| Парткод: | A00J274100 |
| Деталь: | REGULATING PLATE |
| Парткод: | A00J265300 |
| Деталь: | Holding Plate |
| Парткод: | A00J265200 |
| Деталь: | SEAL |
| Парткод: | A00J265800 |
| Деталь: | SEAL |
| Парткод: | 9J06162001 |
| Деталь: | SEAL |
| Парткод: | A00J265500 |
| Деталь: | SEAL |
| Парткод: | A00J265400 |
| Деталь: | Riverse/exit Cover |
| Парткод: | A00J893501 |
| Деталь: | WASHER |
| Парткод: | 1200164603 |
| Деталь: | Neutralizing Brush |
| Парткод: | A02E890700 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J899500 |
| Деталь: | Riverse/exit Roller |
| Парткод: | A0P0893900 |
| Деталь: | ROLL |
| Парткод: | 4004590301 |
| Деталь: | BUSHING |
| Парткод: | A00J890400 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4011585202 |
| Деталь: | BUSHING |
| Парткод: | 4030309301 |
| Деталь: | CONTACT |
| Парткод: | A00J899200 |
| Деталь: | CONTACT |
| Парткод: | A00J896400 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J893402 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J899301 |
| Деталь: | SHAFT |
| Парткод: | 4025598401 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J893201 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J893601 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J893300 |
| Деталь: | GUIDE PART |
| Парткод: | A00J898500 |
| Деталь: | Pulley 24T |
| Парткод: | 4025593901 |
| Деталь: | Paper exit Cover |
| Парткод: | A00J891801 |
| Деталь: | COVER |
| Парткод: | A00J898900 |
| Деталь: | SCREW |
| Парткод: | 4036596601 |
| Деталь: | FAN MOTOR |
| Парткод: | 9J06M10000 |
| Деталь: | Conveyance Relay harness /1 |
| Парткод: | A1DMN11200 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J892101 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J892200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0901000 |
| Деталь: | Paper exit Actuator |
| Парткод: | A00J892300 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J893100 |
| Деталь: | Sensor Plate |
| Парткод: | A00J892700 |
| Деталь: | PROTECTION PART |
| Парткод: | A0P0899600 |
| Деталь: | COVER |
| Парткод: | A00J898400 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | BUSHING |
| Парткод: | 4030309301 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J899700 |
| Деталь: | CONTACT |
| Парткод: | A00J894000 |
| Деталь: | ROLLER |
| Парткод: | A0P0898301 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0P0892901 |
| Деталь: | CUSHION |
| Парткод: | A0P0900500 |
| Деталь: | ROLL |
| Парткод: | A0P0901100 |
| Деталь: | PIN |
| Парткод: | A00J897100 |
| Деталь: | ROLL |
| Парткод: | A00J897000 |
| Деталь: | CONTACT |
| Парткод: | A00J894200 |
| Деталь: | COVER |
| Парткод: | A00J897900 |
| Деталь: | Plate spring /1 |
| Парткод: | A00J892600 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J892001 |
| Деталь: | PROTECTION PART |
| Парткод: | A0P0897600 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0P0892400 |
| Деталь: | SHAFT |
| Парткод: | A00J897800 |
| Деталь: | GEAR 15T |
| Парткод: | A00J896300 |
| Деталь: | GUIDE ASSY |
| Парткод: | A0P0R73711 |
| Деталь: | GEAR 16T |
| Парткод: | A00J896100 |
| Деталь: | MOUNTING PLATE / 1ST EXIT |
| Парткод: | A00JR7B200 |
| Деталь: | BUSHING |
| Парткод: | A0P0900200 |
| Деталь: | TORSION SPRING |
| Парткод: | 4036591301 |
| Деталь: | BUSHING |
| Парткод: | 4004598701 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0900100 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | A0P0900700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0900900 |
| Деталь: | DUCT |
| Парткод: | A0P0154500 |
| Деталь: | DUCT |
| Парткод: | A0P0153300 |
| Деталь: | SEAL |
| Парткод: | A0P0154900 |
| Деталь: | DUCT |
| Парткод: | A0P0152600 |
| Деталь: | SEAL |
| Парткод: | A0P0153700 |
| Деталь: | DUCT |
| Парткод: | A0P0152100 |
| Деталь: | SEAL |
| Парткод: | A00J152700 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0132200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0153100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J154600 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313100072 |
| Деталь: | Smoke suction filter assy |
| Парткод: | A0P0R70100 |
| Деталь: | SEAL |
| Парткод: | 4036248501 |
| Деталь: | SEAL |
| Парткод: | A00J154801 |
| Деталь: | C/K Contact Assy |
| Парткод: | A2WUR70100 |
| Деталь: | CHANGING WIRING/2 |
| Парткод: | AOOJN13700 |
| Деталь: | COMPRESSING COIL SPRING |
| Парткод: | AOP0111900 |
| Деталь: | Chaging Wiring /K |
| Парткод: | AOPON13300 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J895000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J896000 |
| Деталь: | Paper exit belt drive assy |
| Парткод: | A0P0R73600 |
| Деталь: | Pulley 24/29T |
| Парткод: | A00J895200 |
| Деталь: | Timing belt 210L |
| Парткод: | A00J894300 |
| Деталь: | WASHER |
| Парткод: | 1200164603 |
| Деталь: | SHAFT |
| Парткод: | A00J895800 |
| Деталь: | Gear 21/34T |
| Парткод: | A00J895700 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0894900 |
| Деталь: | COVER |
| Парткод: | A00J897700 |
| Деталь: | Pulling Spring |
| Парткод: | A00J899400 |
| Деталь: | CAM |
| Парткод: | A0P0897300 |
| Деталь: | GEAR 16T |
| Парткод: | A00J894600 |
| Деталь: | SHAFT |
| Парткод: | A00J897200 |
| Деталь: | GEAR 16T |
| Парткод: | A00J895300 |
| Деталь: | BUSHING |
| Парткод: | A0P0900000 |
| Деталь: | SHAFT |
| Парткод: | A00J894800 |
| Деталь: | Gear 21T |
| Парткод: | A00J894400 |
| Деталь: | Gear 21T |
| Парткод: | A00J894500 |
| Деталь: | BUSHING |
| Парткод: | 4004533901 |
| Деталь: | ACTUATOR |
| Парткод: | A00J731601 |
| Деталь: | PIN |
| Парткод: | A00J732600 |
| Деталь: | HOLDER |
| Парткод: | A00J732302 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J732502 |
| Деталь: | SHAFT |
| Парткод: | A00J732400 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0708500 |
| Деталь: | HOLDER |
| Парткод: | A0P0707701 |
| Деталь: | Temp. transfer |
| Парткод: | A0P0M50000 |
| Деталь: | Open/close Spring |
| Парткод: | A0P0707600 |
| Деталь: | FLANGE |
| Парткод: | 4004351202 |
| Деталь: | Hold Wire /Rear |
| Парткод: | A00J707102 |
| Деталь: | Guide Wire |
| Парткод: | A00J707501 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J709000 |
| Деталь: | Guide Holder |
| Парткод: | A0P0707400 |
| Деталь: | Sensor Relay harness /3 |
| Парткод: | A0P0N12J00 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Temperature Detection harness |
| Парткод: | A0P0N10U00 |
| Деталь: | Conveyance Duct |
| Парткод: | A00J701500 |
| Деталь: | SEAL |
| Парткод: | A00J709100 |
| Деталь: | Suction Seal |
| Парткод: | A00J701800 |
| Деталь: | COVER |
| Парткод: | A00J701701 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J702400 |
| Деталь: | TORSION SPRING |
| Парткод: | 1164352702 |
| Деталь: | ACTUATOR |
| Парткод: | 1164350403 |
| Деталь: | Wiring Cover |
| Парткод: | A00J702000 |
| Деталь: | Lever /1 |
| Парткод: | A00J711301 |
| Деталь: | HOLD PLATE |
| Парткод: | A00J711500 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J711700 |
| Деталь: | LEVER |
| Парткод: | 4036367502 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | GEAR 20T |
| Парткод: | A00J700600 |
| Деталь: | GEAR 14T |
| Парткод: | A00J702700 |
| Деталь: | BUSHING |
| Парткод: | 4025357201 |
| Деталь: | Pulling Spring |
| Парткод: | A00J701000 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Ground Contact |
| Парткод: | A00J701900 |
| Деталь: | Guide Film |
| Парткод: | A00J704700 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J707801 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A00JR90100 |
| Деталь: | Guide Film |
| Парткод: | A00J704600 |
| Деталь: | Guide Film |
| Парткод: | A00J704200 |
| Деталь: | Neutralizing Holder |
| Парткод: | A00J701600 |
| Деталь: | NETURALIZING MEMBER |
| Парткод: | 4025356801 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J701200 |
| Деталь: | ROLLER |
| Парткод: | A00J700100 |
| Деталь: | ROLLER |
| Парткод: | A00J700201 |
| Деталь: | BUSHING |
| Парткод: | 1164350901 |
| Деталь: | MOUNTING PLATE / PAPER EXIT CONVEYA NCE |
| Парткод: | A00JR7AT00 |
| Деталь: | Gear 34/17T |
| Парткод: | A00J700501 |
| Деталь: | Rotation Knob |
| Парткод: | A00J706900 |
| Деталь: | Positioning Holder |
| Парткод: | A00J703000 |
| Деталь: | GEAR 26T |
| Парткод: | A00J700301 |
| Деталь: | COLLAR |
| Парткод: | A00J700900 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12300 |
| Деталь: | paper exit conveyance assy |
| Парткод: | A0P0R73011 |
| Деталь: | Slide Rail /A |
| Парткод: | A00J631202 |
| Деталь: | SCREW |
| Парткод: | A00J618400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J607100 |
| Деталь: | GROUND PLATE |
| Парткод: | A00J607800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J607401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J607500 |
| Деталь: | Conveyance Roller /A |
| Парткод: | A0P0607000 |
| Деталь: | Conveyance Base frame |
| Парткод: | A0P0606000 |
| Деталь: | BUSHING |
| Парткод: | A0P0663600 |
| Деталь: | Slide Shaft Holder |
| Парткод: | A03U812800 |
| Деталь: | Label LC1 |
| Парткод: | A00J941800 |
| Деталь: | COUPLING SPRING |
| Парткод: | A00J660100 |
| Деталь: | CLEANER COUPLING PART |
| Парткод: | 55VA15541 |
| Деталь: | DOUBLE FEED PREVENTIVE PLATE |
| Парткод: | 55VA40930 |
| Деталь: | Up/down Plate |
| Парткод: | A00J613500 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J623400 |
| Деталь: | LCT UP DOWN WIRE LEFT FRONT |
| Парткод: | 56QA59110 |
| Деталь: | PAD |
| Парткод: | A0P0663900 |
| Деталь: | Stopper Plate /2 |
| Парткод: | A0P0615200 |
| Деталь: | Light blocking Part |
| Парткод: | A00J660300 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | Up/down Pulley |
| Парткод: | A00J613700 |
| Деталь: | Regulating Plate /1 |
| Парткод: | A0P0618900 |
| Деталь: | Gear /1 |
| Парткод: | A0P0663800 |
| Деталь: | Dumper |
| Парткод: | A0P0662700 |
| Деталь: | Protection Cover |
| Парткод: | A00J619011 |
| Деталь: | LCT SLIDE BOARD |
| Парткод: | 56QA58041D |
| Деталь: | Sensor Cover |
| Парткод: | A00J613300 |
| Деталь: | Protection Sheet |
| Парткод: | A00J660600 |
| Деталь: | STOPPER RUBBER |
| Парткод: | A00J663100 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | REGISTRATION UNIT FIXED SCREW |
| Парткод: | 26NA45440 |
| Деталь: | Connecting Plate |
| Парткод: | A00J615000 |
| Деталь: | Protection Sheet |
| Парткод: | A00J660500 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J613200 |
| Деталь: | PFU RELAY HARNESS/1 |
| Парткод: | A00JN11A00 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0P0615700 |
| Деталь: | Up/down Shaft |
| Парткод: | A00J615500 |
| Деталь: | LCT UP DOWN WIRE LEFT REAR |
| Парткод: | 56QA59120 |
| Деталь: | 1500-sheet tray M |
| Парткод: | A0P0R72711 |
| Деталь: | 1500-sheet tray I |
| Парткод: | A0P0R72811 |
| Деталь: | SEAL |
| Парткод: | A2WU156900 |
| Деталь: | Guide Plate /C |
| Парткод: | A00J403402 |
| Деталь: | SEAL |
| Парткод: | A2WU156700 |
| Деталь: | Guide Plate /B |
| Парткод: | A00J403300 |
| Деталь: | Mounting Plate /B |
| Парткод: | A00J135800 |
| Деталь: | REED SWITCH |
| Парткод: | 9334261012 |
| Деталь: | MICRO SWITCH |
| Парткод: | 9J06M60100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J134600 |
| Деталь: | Torsion Coil |
| Парткод: | A00J136500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J135201 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J142800 |
| Деталь: | Toner Relay harness |
| Парткод: | A2WUN10B00 |
| Деталь: | GUIDE RAIL |
| Парткод: | A00J132101 |
| Деталь: | HV Power source /2 |
| Парткод: | A2WUM40800 |
| Деталь: | GUIDE RAIL |
| Парткод: | A00J132600 |
| Деталь: | COVER |
| Парткод: | A00J140900 |
| Деталь: | Guide Holder |
| Парткод: | A00J137800 |
| Деталь: | Guide Rail /Right |
| Парткод: | A0P0132300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J134000 |
| Деталь: | Mounting Plate /2 |
| Парткод: | A2WU134100 |
| Деталь: | HV Power source /1 |
| Парткод: | A2WUM40700 |
| Деталь: | Sensor Cover |
| Парткод: | A00J704100 |
| Деталь: | Sensor Shutter |
| Парткод: | A00J711101 |
| Деталь: | Guide Stopper |
| Парткод: | A00J702901 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J703600 |
| Деталь: | GUIDE PLATE |
| Парткод: | A0P0702200 |
| Деталь: | PIN |
| Парткод: | 4025367601 |
| Деталь: | Wiring Cover |
| Парткод: | A00J704500 |
| Деталь: | Guide Holder /Left |
| Парткод: | A00J702101 |
| Деталь: | LEVER |
| Парткод: | 4036367301 |
| Деталь: | LEVER |
| Парткод: | A00J711601 |
| Деталь: | HOLD PLATE |
| Парткод: | 4025367402 |
| Деталь: | Guide Shutter |
| Парткод: | A00J702600 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | A0P0M50400 |
| Деталь: | PHOTO SENSING ELEMENT |
| Парткод: | V869900045 |
| Деталь: | Sensor Relay harness /4 |
| Парткод: | A2WUN12200 |
| Деталь: | Hold Wire /Front |
| Парткод: | A00J707200 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J706100 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4643460501 |
| Деталь: | Sensor Cover /2 |
| Парткод: | A00J704400 |
| Деталь: | Plate spring /2 |
| Парткод: | A00J703700 |
| Деталь: | TENSION SPRING |
| Парткод: | 4025355601 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J702800 |
| Деталь: | Plate spring /1 |
| Парткод: | A00J702500 |
| Деталь: | Plate spring /3 |
| Парткод: | A00J703800 |
| Деталь: | RESISTOR |
| Парткод: | 9454407602 |
| Деталь: | STOPPER |
| Парткод: | 4036355701 |
| Деталь: | PLATE NUT |
| Парткод: | 4002504202 |
| Деталь: | GUIDE ASSY |
| Парткод: | A0P0R75000 |
| Деталь: | Removal guide assy |
| Парткод: | A0P0R73100 |
| Деталь: | Up/down Plate |
| Парткод: | A00J613500 |
| Деталь: | DOUBLE FEED PREVENTIVE PLATE |
| Парткод: | 55VA40930 |
| Деталь: | FRICTION PLATE |
| Парткод: | A00J623400 |
| Деталь: | LCT UP DOWN WIRE RIGHT FRONT |
| Парткод: | 56QA58110 |
| Деталь: | PAD |
| Парткод: | A0P0663900 |
| Деталь: | Stopper Plate /1 |
| Парткод: | A00J615101 |
| Деталь: | Light blocking Part |
| Парткод: | A00J660300 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | Up/down Pulley |
| Парткод: | A00J613700 |
| Деталь: | Regulating Plate /1 |
| Парткод: | A0P0618900 |
| Деталь: | Gear /1 |
| Парткод: | A0P0663800 |
| Деталь: | Dumper |
| Парткод: | A0P0662700 |
| Деталь: | Protection Cover |
| Парткод: | A00J619011 |
| Деталь: | LCT SLIDE BOARD |
| Парткод: | 56QA58041D |
| Деталь: | EXTERNAL PROTECTION PLATE |
| Парткод: | 56QA58470D |
| Деталь: | Sensor Cover |
| Парткод: | A00J613300 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | Protection Sheet |
| Парткод: | A00J660600 |
| Деталь: | STOPPER RUBBER |
| Парткод: | A00J663100 |
| Деталь: | REGISTRATION UNIT FIXED SCREW |
| Парткод: | 26NA45440 |
| Деталь: | Connecting Plate |
| Парткод: | A00J615000 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J613200 |
| Деталь: | PFU Relay harness /2 |
| Парткод: | A00JN11B01 |
| Деталь: | Receiving Block |
| Парткод: | A00J619300 |
| Деталь: | REGULATING PLATE |
| Парткод: | A0P0615600 |
| Деталь: | Up/down Shaft |
| Парткод: | A00J615500 |
| Деталь: | LCT UP DOWN WIRE RIGHT REAR |
| Парткод: | 56QA58120 |
| Деталь: | 1000-sheet tray M |
| Парткод: | A0P0R72500 |
| Деталь: | 1000-sheet tray I |
| Парткод: | A0P0R72600 |
| Деталь: | REINFORCE PLATE /2 |
| Парткод: | A00J572700 |
| Деталь: | Photoreflector |
| Парткод: | A2WUR90000 |
| Деталь: | Paperfeed Relay harness /4 |
| Парткод: | A00JN11902 |
| Деталь: | BRACKET |
| Парткод: | 4348304901 |
| Деталь: | ROLLER |
| Парткод: | A00J572200 |
| Деталь: | BUSHING |
| Парткод: | 4131353202 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J560502 |
| Деталь: | GUIDE PART |
| Парткод: | A00J561000 |
| Деталь: | GUIDE PART |
| Парткод: | A00J574301 |
| Деталь: | TENSION SPRING |
| Парткод: | 4030312501 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J561300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J561200 |
| Деталь: | SHAFT |
| Парткод: | 4030303901 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A0P0561700 |
| Деталь: | Mounting Plate /S |
| Парткод: | A00J564600 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | Holder /S |
| Парткод: | A00J564700 |
| Деталь: | Guide Roller /Rear |
| Парткод: | A00J574800 |
| Деталь: | Fieldroller assy |
| Парткод: | A0P0R74000 |
| Деталь: | Release Lever |
| Парткод: | A0P0568100 |
| Деталь: | GEAR 24T |
| Парткод: | A0P0570400 |
| Деталь: | Conveyance Belt 74L |
| Парткод: | A0P0568000 |
| Деталь: | Frame/Drive Moter |
| Парткод: | A0P0R7A100 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12600 |
| Деталь: | Paperfeed Drive harness |
| Парткод: | A00JN10F01 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0573100 |
| Деталь: | TORSION SPRING |
| Парткод: | A0P0575500 |
| Деталь: | Drive Holder /2 |
| Парткод: | A00J572600 |
| Деталь: | Conveyance Gear /2 21/31T |
| Парткод: | A00J565300 |
| Деталь: | Conveyance Gear /5 23T |
| Парткод: | A00J565600 |
| Деталь: | Conveyance Gear /4 20/31T |
| Парткод: | A00J565500 |
| Деталь: | GEAR 22T |
| Парткод: | A00J574400 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | Lock Catch |
| Парткод: | A00J574201 |
| Деталь: | Wiring Cover /2 |
| Парткод: | A00J564800 |
| Деталь: | Fieldroller assy |
| Парткод: | A0P0R73911 |
| Деталь: | Fusing Unit 100V |
| Парткод: | A0P0R73222 |
| Деталь: | FUSING UNIT 120V |
| Парткод: | A0P0R73322 |
| Деталь: | FUSING UNIT 200V |
| Парткод: | A0P0R73422 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A0P0138500 |
| Деталь: | AC Relay harness |
| Парткод: | A0P0N10800 |
| Деталь: | Fixing Coil |
| Парткод: | A0P0M40202 |
| Деталь: | Fixing Coil |
| Парткод: | A0P0M40302 |
| Деталь: | Fixing Coil |
| Парткод: | A0P1M40302 |
| Деталь: | Fixing Coil |
| Парткод: | A0P1M40202 |
| Деталь: | Gear 88T |
| Парткод: | A2WU220800 |
| Деталь: | Transfer Shaft |
| Парткод: | A2WU220300 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | Transfer Frame /C |
| Парткод: | A00J220600 |
| Деталь: | GUIDE |
| Парткод: | 4036351701 |
| Деталь: | TRANSFER FRAME / B |
| Парткод: | A00JR7B700 |
| Деталь: | STOPPER RING |
| Парткод: | 1164306501 |
| Деталь: | Gear 59T |
| Парткод: | A2WU220100 |
| Деталь: | Reinforce Plate /T |
| Парткод: | A0P0228900 |
| Деталь: | Transfer Gear /M 55/34T |
| Парткод: | A0P0228100 |
| Деталь: | Pulling Spring |
| Парткод: | A0P0228500 |
| Деталь: | Transfer Shaft /B |
| Парткод: | A0P0228700 |
| Деталь: | Transfer Gear /Y 20T |
| Парткод: | A0P0228200 |
| Деталь: | Transfer Frame /E |
| Парткод: | A0P0228400 |
| Деталь: | Transfer freme / F |
| Парткод: | A0P0R7A600 |
| Деталь: | brushless Motor /20 |
| Парткод: | A00JM11401 |
| Деталь: | SPACER |
| Парткод: | A2WU221200 |
| Деталь: | FLANGE |
| Парткод: | A2WU221001 |
| Деталь: | DC Brushless motor |
| Парткод: | A0EDM10100 |
| Деталь: | Gear 22/33T |
| Парткод: | A00J225100 |
| Деталь: | Stepping motor |
| Парткод: | A02EM10C01 |
| Деталь: | TRANSFER FRAME / D |
| Парткод: | A00JR7B600 |
| Деталь: | GEAR 16/64T |
| Парткод: | A00J225000 |
| Деталь: | MAIN DRIVE ASSY |
| Парткод: | A2WUR70500 |
| Деталь: | PWB Assembly(PWB-EE ASSY) |
| Парткод: | A0P0H00C00 |
| Деталь: | Brushless motor /15 |
| Парткод: | A00JM11000 |
| Деталь: | Gear 44/60T |
| Парткод: | A2WU220000 |
| Деталь: | PIN |
| Парткод: | 4004254701 |
| Деталь: | Transfer Frame /A |
| Парткод: | A2WU220400 |
| Деталь: | Brushless motor /12 |
| Парткод: | A00JM11300 |
| Деталь: | FLANGE |
| Парткод: | A2WU220901 |
| Деталь: | Hold Plate /1 |
| Парткод: | A0P0105100 |
| Деталь: | Cover Handle |
| Парткод: | A0P0165500 |
| Деталь: | Hold Plate /2 |
| Парткод: | A0P0105200 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A00J595200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J102400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0105300 |
| Деталь: | COVER |
| Парткод: | A0P0138200 |
| Деталь: | COVER |
| Парткод: | A0P0138300 |
| Деталь: | PLATE |
| Парткод: | A00J106500 |
| Деталь: | Castor |
| Парткод: | A0P0109001 |
| Деталь: | FAN MOTOR |
| Парткод: | 4556M10000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J137701 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A2WU135400 |
| Деталь: | ROCKER SWITCH |
| Парткод: | A2WUM60000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J134500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0104311 |
| Деталь: | Stay /Lower |
| Парткод: | A00J101400 |
| Деталь: | Stay /Upper |
| Парткод: | A0P0101311 |
| Деталь: | RUBBER FOOT |
| Парткод: | A0P0104600 |
| Деталь: | PLATE |
| Парткод: | A00J106400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J104400 |
| Деталь: | SHEET |
| Парткод: | A0P0109600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J105400 |
| Деталь: | Cover Handle |
| Парткод: | A00J164600 |
| Деталь: | THERMISTOR |
| Парткод: | A0P0M50300 |
| Деталь: | Side plate /Middle |
| Парткод: | A00J101603 |
| Деталь: | Temperature Relay harness |
| Парткод: | A0P0N12P00 |
| Деталь: | COVER |
| Парткод: | A0P0148701 |
| Деталь: | LABEL |
| Парткод: | 957149101 |
| Деталь: | Side plate /Upper |
| Парткод: | A0P0101502 |
| Деталь: | Sealing Part /2 |
| Парткод: | A0P0109300 |
| Деталь: | PROTECTION PART |
| Парткод: | A0P0142101 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J102700 |
| Деталь: | Guide Holder |
| Парткод: | A00J586800 |
| Деталь: | COVER |
| Парткод: | A0P0163800 |
| Деталь: | COVER |
| Парткод: | A2WU135300 |
| Деталь: | SEAL |
| Парткод: | A2WU156400 |
| Деталь: | SEAL |
| Парткод: | A0P0102000 |
| Деталь: | Support Holder |
| Парткод: | A00J595000 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J590500 |
| Деталь: | Guide Plate /Front |
| Парткод: | A0P0587500 |
| Деталь: | Guide Sheet |
| Парткод: | A00J586201 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | SHAFT |
| Парткод: | 4030300301 |
| Деталь: | PIN |
| Парткод: | 1067250101 |
| Деталь: | GEAR 32T |
| Парткод: | 4425301601 |
| Деталь: | CLUTCH |
| Парткод: | A00J595600 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | Paper feed Holder |
| Парткод: | A0P0590100 |
| Деталь: | GEAR 30T |
| Парткод: | 4425301301 |
| Деталь: | GEAR 20T |
| Парткод: | A00J590300 |
| Деталь: | SHAFT |
| Парткод: | 4040309701 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J590400 |
| Деталь: | BUSHING |
| Парткод: | 1065308601 |
| Деталь: | Paper feed Shaft |
| Парткод: | A00J590700 |
| Деталь: | Paper feed Coupling |
| Парткод: | A00J587000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J586100 |
| Деталь: | Paper feed Shaft |
| Парткод: | A00J586000 |
| Деталь: | FRAME /BYPASS (REAR) |
| Парткод: | A00JR7AQ00 |
| Деталь: | Pressing Collar |
| Парткод: | A00J596700 |
| Деталь: | Gear 15/28T |
| Парткод: | A00J595800 |
| Деталь: | GEAR 14T |
| Парткод: | A00J592600 |
| Деталь: | Gear 18/29T |
| Парткод: | A00J592201 |
| Деталь: | Gear 18/35T |
| Парткод: | A00J591700 |
| Деталь: | GEAR 26T |
| Парткод: | A00J592800 |
| Деталь: | Compressing Coil |
| Парткод: | A00J593000 |
| Деталь: | Wiring Cover |
| Парткод: | A00J596000 |
| Деталь: | Support Plate |
| Парткод: | A0P0101201 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | SPRING |
| Парткод: | 4038229401 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0107700 |
| Деталь: | HOLDER |
| Парткод: | 4038229501 |
| Деталь: | Holder /Black |
| Парткод: | A0P0107600 |
| Деталь: | SPRING |
| Парткод: | 4038229301 |
| Деталь: | Drawer CN |
| Парткод: | V651020004 |
| Деталь: | Guide Post |
| Парткод: | A00J105601 |
| Деталь: | Positioning Pin /Front |
| Парткод: | A0P0382400 |
| Деталь: | Cover /Inside |
| Парткод: | A2WU166901 |
| Деталь: | SEAL |
| Парткод: | A2WU157000 |
| Деталь: | HOLDER |
| Парткод: | A00J135900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J137500 |
| Деталь: | SHAFT |
| Парткод: | A00J102301 |
| Деталь: | SEAL |
| Парткод: | A2WU156200 |
| Деталь: | PH Assy |
| Парткод: | A2WUR70000 |
| Деталь: | Control Relay harness /3 |
| Парткод: | A2WUN12G00 |
| Деталь: | PWB Assembly (PWB-J ASSY) |
| Парткод: | A2WUH00300 |
| Деталь: | SEAL |
| Парткод: | A2WU156300 |
| Деталь: | SEAL |
| Парткод: | A2WU156000 |
| Деталь: | SEAL |
| Парткод: | A2WU156100 |
| Деталь: | Read Cover /Right |
| Парткод: | A0P0163300 |
| Деталь: | COVER |
| Парткод: | A00J169100 |
| Деталь: | Read Cover /Front |
| Парткод: | A0P0165800 |
| Деталь: | COVER |
| Парткод: | A02E167700 |
| Деталь: | COVER |
| Парткод: | A0P0165200 |
| Деталь: | Read Cover |
| Парткод: | A0P0167600 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J169200 |
| Деталь: | Label Legal Restiriction |
| Парткод: | A00J940100 |
| Деталь: | LABEL |
| Парткод: | A00J940200 |
| Деталь: | Read Cover /Upper |
| Парткод: | A00J167103 |
| Деталь: | Read Cover /Front |
| Парткод: | A0P0163001 |
| Деталь: | Light blocking Plate |
| Парткод: | A00J168902 |
| Деталь: | Lens /B |
| Парткод: | A00J168202 |
| Деталь: | Light blocking Cover /C |
| Парткод: | A00J168503 |
| Деталь: | PWB Assembly LED2 |
| Парткод: | A00JH00E00 |
| Деталь: | Scanner Wiring /6 |
| Парткод: | A0P0N14600 |
| Деталь: | Read Cover /Left |
| Парткод: | A0P0165900 |
| Деталь: | SEAL |
| Парткод: | A0P0166600 |
| Деталь: | Read Cover /Left |
| Парткод: | A0P0163201 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0267900 |
| Деталь: | Read Cover /Upper |
| Парткод: | A00J167811 |
| Деталь: | Read Cover /Rear |
| Парткод: | A0P0163101 |
| Деталь: | FILTER |
| Парткод: | 4025228502 |
| Деталь: | Label Cleaning |
| Парткод: | A0P0947700 |
| Деталь: | Read Cover /Upper |
| Парткод: | A0P0167201 |
| Деталь: | LABEL |
| Парткод: | A0P0948700 |
| Деталь: | STAY |
| Парткод: | A0P0133701 |
| Деталь: | COVER |
| Парткод: | A00J139000 |
| Деталь: | COVER |
| Парткод: | A00J139100 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0133800 |
| Деталь: | ROCKER SWITCH |
| Парткод: | A00JM60300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J136400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J134702 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J140401 |
| Деталь: | LABEL |
| Парткод: | 9J06730101 |
| Деталь: | COVER |
| Парткод: | A00J138900 |
| Деталь: | BRACKET |
| Парткод: | 4037223902 |
| Деталь: | AC Relay harness /1 |
| Парткод: | A00JN10701Old |
| Деталь: | AC Relay harness /1 |
| Парткод: | A00JN10712 |
| Деталь: | AC Relay harness |
| Парткод: | A00JN10N00 |
| Деталь: | SUPPORT |
| Парткод: | V502010026 |
| Деталь: | POWER CORD |
| Парткод: | 4037077501 |
| Деталь: | Power source Cord /120V |
| Парткод: | A0P0N30000 |
| Деталь: | POWER CORD |
| Парткод: | A00JN30100 |
| Деталь: | Power code |
| Парткод: | A00JN30200 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J140501 |
| Деталь: | POWER SOURCE TRANSFORMER |
| Парткод: | 56AA84520 |
| Деталь: | Power Source Transfomer |
| Парткод: | 56AF84521 |
| Деталь: | POWER SOURCE TRANSFORMER |
| Парткод: | 56AE84520 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J140800 |
| Деталь: | NOISE FILTER |
| Парткод: | 56QE88261 |
| Деталь: | Circuit Board Spacer |
| Парткод: | V502010057 |
| Деталь: | PLATE SPRING |
| Парткод: | A0P0148801 |
| Деталь: | Circuit Board Spacer |
| Парткод: | V502010056 |
| Деталь: | PWB Assembly RL |
| Парткод: | A00JH00400 |
| Деталь: | PWB Assembly (PWB-KH ASSY) |
| Парткод: | A0P0H00200 |
| Деталь: | COVER |
| Парткод: | A2WU133900 |
| Деталь: | COVER |
| Парткод: | A00J137900 |
| Деталь: | Control Relay harness /1 |
| Парткод: | A0P0N12E00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J136302 |
| Деталь: | Paperfeed Control harness |
| Парткод: | A0P0N10300 |
| Деталь: | REAR COVER |
| Парткод: | A01H160201 |
| Деталь: | GUIDE |
| Парткод: | 9J07200903 |
| Деталь: | FUN MOTOR |
| Парткод: | 9J07M10300 |
| Деталь: | SCREW |
| Парткод: | 4002258101 |
| Деталь: | PWB Assembly (PWB-ADF ASSY) |
| Парткод: | A0HTRA0101 |
| Деталь: | SHIELD |
| Парткод: | 9J07201403 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J07492402 |
| Деталь: | PLATE SPRING |
| Парткод: | 9J07492302 |
| Деталь: | GUIDE |
| Парткод: | A01H100400 |
| Деталь: | HINGE |
| Парткод: | A0HT100800 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 9J07210901 |
| Деталь: | HINGE |
| Парткод: | A0HT100900 |
| Деталь: | GUIDE |
| Парткод: | A01H100300 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A07H100700 |
| Деталь: | ADF Wiring |
| Парткод: | A0HTN10600 |
| Деталь: | Donau DF unit |
| Парткод: | A0HTR70011 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0575101 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4030308101 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4030322402 |
| Деталь: | HOLDER |
| Парткод: | 4030308301 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | LEVER |
| Парткод: | 4030309101 |
| Деталь: | PWB ASSY |
| Парткод: | 4037010401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J575302 |
| Деталь: | Rail /Left |
| Парткод: | A00J133200 |
| Деталь: | COVER |
| Парткод: | A0P0138600 |
| Деталь: | Paperfeed Relay Harness /1 |
| Парткод: | A00JN11601 |
| Деталь: | Paperfeed Relay harness /2 |
| Парткод: | A00JN11702 |
| Деталь: | HOLDER |
| Парткод: | 4011301201 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4002313101 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4002311001 |
| Деталь: | MOTOR |
| Парткод: | 9J06M10300 |
| Деталь: | HOLDER |
| Парткод: | 4030304702 |
| Деталь: | Light blocking Cover |
| Парткод: | A00J168301 |
| Деталь: | Lens /A |
| Парткод: | A00J168102 |
| Деталь: | Light blocking Plate |
| Парткод: | A00J168801 |
| Деталь: | Cover Cassette /Right |
| Парткод: | A00J160801 |
| Деталь: | Cover LCC Info |
| Парткод: | A00J161102 |
| Деталь: | Light blocking Cover |
| Парткод: | A00J168400 |
| Деталь: | PWB Assembly LED1 |
| Парткод: | A00JH00D00 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J164501 |
| Деталь: | COVER |
| Парткод: | A00J168600 |
| Деталь: | COVER |
| Парткод: | A00J168700 |
| Деталь: | INDICATING RELAY HARNESS/1 |
| Парткод: | A00JN10D00 |
| Деталь: | Label bizhub 602 |
| Парткод: | A2WU944900 |
| Деталь: | Label bizhub 652 |
| Парткод: | A2WU943300 |
| Деталь: | Label bizhub 502 |
| Парткод: | A2WV945000 |
| Деталь: | Label bizhub 552 |
| Парткод: | A2WV943400 |
| Деталь: | Cover LCC Right |
| Парткод: | A00J161001 |
| Деталь: | Cover LCC Right |
| Парткод: | A00J165000 |
| Деталь: | Cover LCC Left |
| Парткод: | A00J164903 |
| Деталь: | Cover LCC Left |
| Парткод: | A00J160901 |
| Деталь: | HINGE |
| Парткод: | A0P0162100 |
| Деталь: | Mounting Plate /B |
| Парткод: | A0P0162600 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475260302 |
| Деталь: | LABEL |
| Парткод: | A2WU944000 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | BAND |
| Парткод: | 4120101402 |
| Деталь: | Open/close Cover /Front |
| Парткод: | A0P0160301 |
| Деталь: | Seal /B |
| Парткод: | A00J114901 |
| Деталь: | Ozone Duct /B |
| Парткод: | A0P0113600 |
| Деталь: | Mounting Plate /Black |
| Парткод: | A0P0120800 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Ozone Duct /Inside |
| Парткод: | A00J113800 |
| Деталь: | Seal /Upper |
| Парткод: | A00J116201 |
| Деталь: | Seal /Inside |
| Парткод: | A0P0115000 |
| Деталь: | Seal /Lower |
| Парткод: | A00J116100 |
| Деталь: | Ozone Duct /Front |
| Парткод: | A00J116400 |
| Деталь: | Ozone Duct /Rear |
| Парткод: | A00J116301 |
| Деталь: | Ozone Duct /A |
| Парткод: | A0P0119700 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313100072 |
| Деталь: | SEAL |
| Парткод: | 4036248501 |
| Деталь: | Ozone Duct /B |
| Парткод: | A0P0119800 |
| Деталь: | SEAL |
| Парткод: | A00J116511 |
| Деталь: | OZONE FILTER |
| Парткод: | A00JR73100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J619901 |
| Деталь: | INTERNAL HEATER |
| Парткод: | 56AA83061D |
| Деталь: | SCREW |
| Парткод: | A00J618400 |
| Деталь: | Slide Rail /A |
| Парткод: | A00J613401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J608400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J608600 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J608100 |
| Деталь: | Mounting Plate /1 |
| Парткод: | A00J608000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J608500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J608200 |
| Деталь: | Shaft /L |
| Парткод: | A00J617600 |
| Деталь: | TRAY POSITIONING SPRING |
| Парткод: | 56QA11230 |
| Деталь: | TRAY PRESSING PLATE |
| Парткод: | 56AA41711 |
| Деталь: | ROLL |
| Парткод: | A00J663000 |
| Деталь: | SHAFT |
| Парткод: | A00J623300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J608300 |
| Деталь: | HANDLE |
| Парткод: | A00J810302 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4497310603 |
| Деталь: | Guide Part /Front |
| Парткод: | A00J814600 |
| Деталь: | Cover /Front |
| Парткод: | A00J810400 |
| Деталь: | GEAR 48T |
| Парткод: | A0P0812800 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | Mounting Plate /B |
| Парткод: | A00JR7AV00 |
| Деталь: | Gear 22/48T |
| Парткод: | A0P0812900 |
| Деталь: | Belt 248L |
| Парткод: | A00J813000 |
| Деталь: | WASHER |
| Парткод: | 1200164603 |
| Деталь: | ROLL |
| Парткод: | A00J813600 |
| Деталь: | Torsion Spring /Lower |
| Парткод: | A00J812400 |
| Деталь: | STOP RING |
| Парткод: | 910362001 |
| Деталь: | LEVER |
| Парткод: | A00J812300 |
| Деталь: | Pulley 26T |
| Парткод: | A00J812200 |
| Деталь: | Pulley 22T |
| Парткод: | 4657371301 |
| Деталь: | Mounting Plate /D |
| Парткод: | A00JR7AW00 |
| Деталь: | MOUNTING PLATE /C |
| Парткод: | A00JR7AX11 |
| Деталь: | Roller /4 |
| Парткод: | A00J811000 |
| Деталь: | ROLL |
| Парткод: | A00J814101 |
| Деталь: | SHAFT |
| Парткод: | A00J814411 |
| Деталь: | SPRING |
| Парткод: | A00J814500 |
| Деталь: | BASE FRAME |
| Парткод: | A00J810124 |
| Деталь: | Actuator /Upper |
| Парткод: | A00J811800 |
| Деталь: | TORSION SPRING |
| Парткод: | 4657373501 |
| Деталь: | Roller /1 |
| Парткод: | A00J810800 |
| Деталь: | PIN |
| Парткод: | 1067250101 |
| Деталь: | KNOB |
| Парткод: | A00J815100 |
| Деталь: | Mounting Plate /A |
| Парткод: | A00JR7AY00 |
| Деталь: | Torsion Spring /Upper |
| Парткод: | A00J812100 |
| Деталь: | Pulley 22T |
| Парткод: | A00J811200 |
| Деталь: | LEVER |
| Парткод: | A00J815200 |
| Деталь: | Belt 306L |
| Парткод: | A00J811600 |
| Деталь: | STOPPER |
| Парткод: | A00J816400 |
| Деталь: | Guide Part /Rear |
| Парткод: | A00J814700 |
| Деталь: | Open/close Cover |
| Парткод: | A00J810504 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J815801 |
| Деталь: | SEAL |
| Парткод: | A0P0267600 |
| Деталь: | SEAL |
| Парткод: | 4581162501 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0267501 |
| Деталь: | REED SWITCH |
| Парткод: | 9334261012 |
| Деталь: | LOUDSPEAKER |
| Парткод: | 4040M40100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0263800 |
| Деталь: | SEAL |
| Парткод: | 9J06163500 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140061 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0262200 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0P0263100 |
| Деталь: | GUIDE |
| Парткод: | A0P0267300 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0P0263400 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A0P0267000 |
| Деталь: | SEAL |
| Парткод: | A00J262901 |
| Деталь: | SEAL |
| Парткод: | A00J263001 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0281801 |
| Деталь: | Mounting Plate /Right rear |
| Парткод: | A0P0263300 |
| Деталь: | SEAL |
| Парткод: | A00J166700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0267800 |
| Деталь: | FRAME |
| Парткод: | A0P0262102 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 9J07210802 |
| Деталь: | FRAME |
| Парткод: | A0P0261900 |
| Деталь: | FRAME |
| Парткод: | A0P0262000 |
| Деталь: | Mounting Plate /B |
| Парткод: | A00J631402 |
| Деталь: | Guide Film |
| Парткод: | A00J621301 |
| Деталь: | Mounting Plate /A |
| Парткод: | A00J631301 |
| Деталь: | COVER CASSETTE |
| Парткод: | A00J160702 |
| Деталь: | LEVER |
| Парткод: | A00J621400 |
| Деталь: | Label Cd |
| Парткод: | A00J942102 |
| Деталь: | Label FD |
| Парткод: | A00J942202 |
| Деталь: | Label FD |
| Парткод: | A00J942302 |
| Деталь: | ROLL |
| Парткод: | A00J663000 |
| Деталь: | SHAFT |
| Парткод: | A00J623300 |
| Деталь: | TRAY PRESSING PLATE |
| Парткод: | 56AA41711 |
| Деталь: | Mounting Plate /L |
| Парткод: | A00J622300 |
| Деталь: | Shaft /L |
| Парткод: | A00J622600 |
| Деталь: | TRAY POSITIONING SPRING |
| Парткод: | 56QA11230 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J622900 |
| Деталь: | GUIDE |
| Парткод: | 4030322812 |
| Деталь: | STOPPER |
| Парткод: | A00J631100 |
| Деталь: | Guide Sheet |
| Парткод: | A00J630500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J631002 |
| Деталь: | GUIDE SHEET/2 |
| Парткод: | A00J631900 |
| Деталь: | Mounting Plate /L |
| Парткод: | A00J631500 |
| Деталь: | EARTH GROUND |
| Парткод: | 4030322303 |
| Деталь: | Pulling Spring |
| Парткод: | A0P0623800 |
| Деталь: | REGULATING PLATE R ASSY |
| Парткод: | A00JR74300 |
| Деталь: | Mounting Plate /Left |
| Парткод: | A0P0108400 |
| Деталь: | Slide Rail |
| Парткод: | A0P0125000 |
| Деталь: | SPACER |
| Парткод: | A0P0108100 |
| Деталь: | Rail /E |
| Парткод: | A0P0110501 |
| Деталь: | SEALING PART |
| Парткод: | A0P0108900 |
| Деталь: | Scatteringprevention Duct |
| Парткод: | A0P0108623 |
| Деталь: | SEAL |
| Парткод: | A0P0125311 |
| Деталь: | Cushion /Lower |
| Парткод: | A00J121200 |
| Деталь: | SEALING PART |
| Парткод: | A0P0108300 |
| Деталь: | Ozone Seal /Black |
| Парткод: | A0P0114100 |
| Деталь: | Mounting Plate /Lower |
| Парткод: | A0P0108201 |
| Деталь: | Protection Cushion |
| Парткод: | A0P0109701 |
| Деталь: | Mounting Plate /Right |
| Парткод: | A0P0108500 |
| Деталь: | Protection Seal |
| Парткод: | A2WU134200 |
| Деталь: | SCREW |
| Парткод: | A0P0382700 |
| Деталь: | LEVER |
| Парткод: | A01H700101 |
| Деталь: | SEAL |
| Парткод: | 9J07160302 |
| Деталь: | LABEL HANDLE |
| Парткод: | 9J07940400 |
| Деталь: | GUIDE |
| Парткод: | A0HT701200 |
| Деталь: | GUIDE |
| Парткод: | A0HT810200 |
| Деталь: | TENSION SPRING |
| Парткод: | 9J07410701 |
| Деталь: | Neutralizing Brush |
| Парткод: | A0HT704000 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 9J07400401 |
| Деталь: | SHAFT |
| Парткод: | 9J07400501 |
| Деталь: | BRACKET ASSY |
| Парткод: | 9J07R70900 |
| Деталь: | GUIDE |
| Парткод: | A0HT700800 |
| Деталь: | GUIDE |
| Парткод: | A07H750400 |
| Деталь: | GUIDE |
| Парткод: | A0HT700900 |
| Деталь: | GUIDE |
| Парткод: | A0HT701000 |
| Деталь: | GUIDE |
| Парткод: | A07H750500 |
| Деталь: | GUIDE |
| Парткод: | A0HT701300 |
| Деталь: | SHIELD PLATE |
| Парткод: | 9J07411601 |
| Деталь: | TORSION COIL SPRING |
| Парткод: | A0HT704200 |
| Деталь: | BRACKET |
| Парткод: | 9J07400601 |
| Деталь: | ROLL |
| Парткод: | 9J07810300 |
| Деталь: | PLATE SPRING |
| Парткод: | A0HT704100 |
| Деталь: | LEFT COVER ASSY |
| Парткод: | A0HTR70111 |
| Деталь: | Open/ciose Guide assy |
| Парткод: | A0HTR70800 |
| Деталь: | Cover Upper |
| Парткод: | A0HT560812 |
| Деталь: | Label Size |
| Парткод: | A0HT940500 |
| Деталь: | Label JAM |
| Парткод: | A01H940701 |
| Деталь: | SHOULDER SCREW |
| Парткод: | 4643300701 |
| Деталь: | ARM |
| Парткод: | 9J07301702 |
| Деталь: | BRACKET |
| Парткод: | 9J07302001 |
| Деталь: | SHAFT |
| Парткод: | 9J07301902 |
| Деталь: | TENSION SPRING |
| Парткод: | 9J07301601 |
| Деталь: | BRACKET ASSY |
| Парткод: | 9J07R71000 |
| Деталь: | BRACKET |
| Парткод: | 9J07331801 |
| Деталь: | LEVER |
| Парткод: | A0HT562300 |
| Деталь: | TORSION SPRING |
| Парткод: | A07H570700 |
| Деталь: | STOPPER RING |
| Парткод: | 1033440203 |
| Деталь: | BUSHING |
| Парткод: | 4469346501 |
| Деталь: | ARM |
| Парткод: | A07H570100 |
| Деталь: | SHAFT |
| Парткод: | 9J07330201 |
| Деталь: | PIN |
| Парткод: | 1067250101 |
| Деталь: | CLUTCH |
| Парткод: | A07H570500 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | BRACKET |
| Парткод: | A07H570600 |
| Деталь: | TENSION SPRING |
| Парткод: | A07H570400 |
| Деталь: | ADF Wiring |
| Парткод: | A0HTN10400 |
| Деталь: | GUIDE |
| Парткод: | 9J07332102 |
| Деталь: | Photoreflector |
| Парткод: | A03TM50000 |
| Деталь: | BRACKET |
| Парткод: | A07H570200 |
| Деталь: | BRACKET |
| Парткод: | A07H570800 |
| Деталь: | Neutralizing Brush |
| Парткод: | A01H565100 |
| Деталь: | GUIDE |
| Парткод: | A07H570001 |
| Деталь: | GEAR 17T |
| Парткод: | 9J07500201 |
| Деталь: | SHAFT |
| Парткод: | 9J07330301 |
| Деталь: | ROLLER |
| Парткод: | 9J07330101 |
| Деталь: | Pulley 21T |
| Парткод: | 9J07330801 |
| Деталь: | Light blocking Part |
| Парткод: | A0HT562200 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | TIMING BELT 122L |
| Парткод: | 4641351401 |
| Деталь: | Pulley 19T |
| Парткод: | 9J07331901 |
| Деталь: | ARM |
| Парткод: | A07H570300 |
| Деталь: | HOLDER |
| Парткод: | A0HT562800 |
| Деталь: | Cover /Rear |
| Парткод: | A0P0161902 |
| Деталь: | COVER |
| Парткод: | A0P0165601 |
| Деталь: | COVER |
| Парткод: | A0P0165701 |
| Деталь: | Cover /Rear |
| Парткод: | A0P0162003 |
| Деталь: | COVER |
| Парткод: | A0P0165301 |
| Деталь: | Label Dehumidifier SW. |
| Парткод: | A00J945400 |
| Деталь: | Cover /Rear |
| Парткод: | A00J161803 |
| Деталь: | Label Only connect |
| Парткод: | A00J945000 |
| Деталь: | Cover /Rear |
| Парткод: | A0P0161700 |
| Деталь: | Cover /Rear |
| Парткод: | A0P0161602 |
| Деталь: | Fixing Plate /Right |
| Парткод: | A0P0364800 |
| Деталь: | KNOB |
| Парткод: | A00J365001 |
| Деталь: | Guide Part /Right |
| Парткод: | A0P0366000 |
| Деталь: | Bottle(Toner Colection) |
| Парткод: | A2WYWY1 |
| Деталь: | Guide Part /Middle |
| Парткод: | A0P0366200 |
| Деталь: | Collection Shutter |
| Парткод: | A00J361100 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J361200 |
| Деталь: | Collection Pipe |
| Парткод: | A00J361700 |
| Деталь: | Conveyance Screw |
| Парткод: | A00J360800 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037090101 |
| Деталь: | Guide Part /Left |
| Парткод: | A0P0366100 |
| Деталь: | GEAR 27T |
| Парткод: | A0P0362900 |
| Деталь: | Drive Gear /10 17T |
| Парткод: | A0P0364100 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | SHAFT |
| Парткод: | A0P0364200 |
| Деталь: | Fixing Plate |
| Парткод: | A2WUR70400 |
| Деталь: | Fixing Plate /Left |
| Парткод: | A0P0364900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0366301 |
| Деталь: | Collection Casing |
| Парткод: | A0P0360700 |
| Деталь: | Bushing /B |
| Парткод: | 65AA32501 |
| Деталь: | Drive Shaft /2 |
| Парткод: | A00J361900 |
| Деталь: | GEAR 20T |
| Парткод: | A00J362700 |
| Деталь: | Gear 38/35T |
| Парткод: | A00J363000 |
| Деталь: | BUSHING |
| Парткод: | A0P0364000 |
| Деталь: | GEAR 30T |
| Парткод: | A00J362500 |
| Деталь: | Gear 30/20T |
| Парткод: | A00J362400 |
| Деталь: | GEAR 28T |
| Парткод: | A0P0368500 |
| Деталь: | GEAR 34T |
| Парткод: | A2WU364100 |
| Деталь: | Stepping motor |
| Парткод: | A00JM12100 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0361000 |
| Деталь: | GEAR 18T |
| Парткод: | A00J362600 |
| Деталь: | GEAR 40T |
| Парткод: | A00J362800 |
| Деталь: | Gear26T |
| Парткод: | A0P0368400 |
| Деталь: | Drive Shaft /1 |
| Парткод: | A00J361800 |
| Деталь: | BUSHING |
| Парткод: | A0P0368200 |
| Деталь: | SEAL |
| Парткод: | A0P0368600 |
| Деталь: | Agitating Paddle |
| Парткод: | A0P0368100 |
| Деталь: | GEAR 38T |
| Парткод: | A00J361000 |
| Деталь: | Sealing Shutter |
| Парткод: | A00J365402 |
| Деталь: | Toner collection assy |
| Парткод: | A0P0R71311 |
| Деталь: | SEAL |
| Парткод: | A0P0366400 |
| Деталь: | Toner Supply Duct Assy |
| Парткод: | A0P0R74200 |
| Деталь: | Mounting Plate /2 |
| Парткод: | A0P0361100 |
| Деталь: | GEAR 22T |
| Парткод: | A2WU362900 |
| Деталь: | Stepping motor |
| Парткод: | A02EM10A00 |
| Деталь: | Vibrationproof Rubber |
| Парткод: | A0P0276700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0276600 |
| Деталь: | TENSION SPRING |
| Парткод: | 4002145801 |
| Деталь: | Belt 210L |
| Парткод: | A0ED275600 |
| Деталь: | Pulley 84T |
| Парткод: | A0P0275500 |
| Деталь: | BEARING |
| Парткод: | A0ED276500 |
| Деталь: | PULLEY |
| Парткод: | A00J275300 |
| Деталь: | Wire /Rear |
| Парткод: | A00J275200 |
| Деталь: | SHAFT |
| Парткод: | A00J275400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J280101 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | 4037090301 |
| Деталь: | LEVER |
| Парткод: | A00J280200 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4036172001 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J276100 |
| Деталь: | Scanner Wiring /5 |
| Парткод: | A0P0N14500 |
| Деталь: | SOLID STATE SWITCH |
| Парткод: | 9335140081 |
| Деталь: | Wire /Front |
| Парткод: | A00J275100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J276000 |
| Деталь: | GUIDE PART |
| Парткод: | A00J276300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J275901 |
| Деталь: | PULLEY |
| Парткод: | A00J275800 |
| Деталь: | Pulling Spring |
| Парткод: | A00J276800 |
| Деталь: | SEAL |
| Парткод: | A00J290500 |
| Деталь: | CCD Lens Assy |
| Парткод: | A0P0R70800 |
| Деталь: | FERRITECORE |
| Парткод: | A0P0M90000 |
| Деталь: | COVER |
| Парткод: | A0P0278500 |
| Деталь: | Scanner Wiring /3 |
| Парткод: | A0P0N14300 |
| Деталь: | FERRITE CORE |
| Парткод: | 816620101 |
| Деталь: | Paper exit Cover /Right |
| Парткод: | A00J163502 |
| Деталь: | Cover /Front |
| Парткод: | A2WU160400 |
| Деталь: | BAND |
| Парткод: | 4120101402 |
| Деталь: | COVER |
| Парткод: | A2WU163600 |
| Деталь: | MAGNET CATCH |
| Парткод: | 4475260302 |
| Деталь: | Mounting Plate /D |
| Парткод: | A00J166001 |
| Деталь: | Open/close Cover |
| Парткод: | A00J160201 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | Logo Mark |
| Парткод: | A00J945500 |
| Деталь: | CATCH |
| Парткод: | 4030104002 |
| Деталь: | MAGNET |
| Парткод: | 9326282011 |
| Деталь: | Toner Wiring |
| Парткод: | A2WUN10G00 |
| Деталь: | Cover /Inside |
| Парткод: | A00J165103 |
| Деталь: | SPACER |
| Парткод: | A00J404700 |
| Деталь: | Label TN618 |
| Парткод: | A2WU948600 |
| Деталь: | Paper exit Cover /Rear |
| Парткод: | A00J163401 |
| Деталь: | Paper exit Cover /Front |
| Парткод: | A00J160100 |
| Деталь: | Paper exit Cover /Right |
| Парткод: | A00J166400 |
| Деталь: | Label TC Exchange |
| Парткод: | A2WU940300 |
| Деталь: | Open/close Shaft |
| Парткод: | A00J164701 |
| Деталь: | Paper exit Cover /Rear |
| Парткод: | A00J166300 |
| Деталь: | Regulating Block /Black |
| Парткод: | A2WU404800 |
| Деталь: | Regulating Block /Black |
| Парткод: | A2WU405800 |
| Деталь: | Regulating Block /Black |
| Парткод: | A2WU405900 |
| Деталь: | HOLDER |
| Парткод: | A00J407500 |
| Деталь: | LABEL K |
| Парткод: | A00J940700 |
| Деталь: | SEAL |
| Парткод: | A00J407400 |
| Деталь: | Claw /Black |
| Парткод: | A0P0169600 |
| Деталь: | SUCTION PLATE |
| Парткод: | 4038101401 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J404601 |
| Деталь: | HOLDER |
| Парткод: | 4038228104 |
| Деталь: | CONNECTOR PIN |
| Парткод: | 4136675101 |
| Деталь: | PLATE SPRING |
| Парткод: | 4038228203 |
| Деталь: | Cover /Inside |
| Парткод: | A2WU166800 |
| Деталь: | Stepping motor |
| Парткод: | A0P0M12200 |
| Деталь: | Drive Shaft /5 |
| Парткод: | A00J611300 |
| Деталь: | Drive Shaft /1 |
| Парткод: | A00J616900 |
| Деталь: | CLUTCH |
| Парткод: | A00JM20000 |
| Деталь: | GEAR 32T |
| Парткод: | A00J612100 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J617700 |
| Деталь: | BALL BEARING |
| Парткод: | A00V240600 |
| Деталь: | MOUNTING PLATE / LCC LENGTH CONVEYA NCE |
| Парткод: | A00JR7AF00 |
| Деталь: | Gear 31T |
| Парткод: | A00J616200 |
| Деталь: | GEAR 44T |
| Парткод: | A00J616300 |
| Деталь: | COLLAR |
| Парткод: | A00J700900 |
| Деталь: | SHAFT STOPPER |
| Парткод: | 55VA42120 |
| Деталь: | GEAR 25T |
| Парткод: | A00J612500 |
| Деталь: | Fixing Plate /1 |
| Парткод: | A00J610200 |
| Деталь: | Gear 40/33T |
| Парткод: | A00J611600 |
| Деталь: | Timing belt 633L |
| Парткод: | A00J610600 |
| Деталь: | Gear 67T |
| Парткод: | A00J611500 |
| Деталь: | Holding Part /1 |
| Парткод: | A00J612600 |
| Деталь: | Drive Shaft /1 |
| Парткод: | A00J610801 |
| Деталь: | Fixing Plate |
| Парткод: | A00J610300 |
| Деталь: | Pulley 33T |
| Парткод: | A00J612200 |
| Деталь: | PIN |
| Парткод: | 4004254701 |
| Деталь: | GEAR 29T |
| Парткод: | A00J611700 |
| Деталь: | Regulating Part |
| Парткод: | A00J612800 |
| Деталь: | Tension Roll |
| Парткод: | A0P0666400 |
| Деталь: | Mounting plate /Belt tension |
| Парткод: | A0P0R7A200 |
| Деталь: | BELT TENSION SPRING |
| Парткод: | 56QA15190 |
| Деталь: | GEAR 30T |
| Парткод: | A00J611900 |
| Деталь: | Drive Shaft /4 |
| Парткод: | A00J611200 |
| Деталь: | DC Brushless motor |
| Парткод: | A0EDM10100 |
| Деталь: | Gear 33T |
| Парткод: | A00J611800 |
| Деталь: | Drive Shaft /2 |
| Парткод: | A00J611000 |
| Деталь: | Drive Shaft /3 |
| Парткод: | A00J611100 |
| Деталь: | COVER |
| Парткод: | A00J137600 |
| Деталь: | MOUNTING PLATE / LCC DRIVE 2 |
| Парткод: | A00JR7AJ00 |
| Деталь: | GEAR 29T |
| Парткод: | A00J616400 |
| Деталь: | Gear 33T |
| Парткод: | A00J616500 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J616600 |
| Деталь: | GEAR 35T |
| Парткод: | A00J616800 |
| Деталь: | GEAR 35T |
| Парткод: | A00J613000 |
| Деталь: | GEAR 29T |
| Парткод: | A00J612000 |
| Деталь: | WAVE WASHER |
| Парткод: | 1500266013 |
| Деталь: | Mounting plate / LCC drive 1 |
| Парткод: | A0P0R7A300 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | PIN |
| Парткод: | 4131253602 |
| Деталь: | SHAFT |
| Парткод: | A07H211700 |
| Деталь: | GEAR 28T |
| Парткод: | A07H212400 |
| Деталь: | Gear 17/28T |
| Парткод: | A07H212600 |
| Деталь: | Timing Belt 278L |
| Парткод: | A07H211800 |
| Деталь: | Tension Plate Assy |
| Парткод: | A07HR71000 |
| Деталь: | TENSION SPRING |
| Парткод: | A07H212100 |
| Деталь: | BRACKET |
| Парткод: | 9J07303801 |
| Деталь: | BRACKET |
| Парткод: | 9J07303201 |
| Деталь: | Holder /Rear |
| Парткод: | A0HT561700 |
| Деталь: | Holder /Front |
| Парткод: | A0HT561600 |
| Деталь: | BRACKET |
| Парткод: | 9J07303101 |
| Деталь: | BUSHING |
| Парткод: | 4658351602 |
| Деталь: | CAM |
| Парткод: | 9J07430901 |
| Деталь: | GEAR 26T |
| Парткод: | 9J07431101 |
| Деталь: | ROLLER |
| Парткод: | A0HT700600 |
| Деталь: | COLLAR |
| Парткод: | 9J07502001 |
| Деталь: | GEAR 17T |
| Парткод: | 9J07500201 |
| Деталь: | BUSHING |
| Парткод: | 4131253701 |
| Деталь: | ROLL |
| Парткод: | 9J07501901 |
| Деталь: | GEAR 40/37T |
| Парткод: | 9J07501201 |
| Деталь: | GEAR 37T |
| Парткод: | A07H212500 |
| Деталь: | GEAR 15/15T |
| Парткод: | A07H212300 |
| Деталь: | Registration Lower Motor Assy |
| Парткод: | A0HTR71100 |
| Деталь: | PAPER FEED MOTOR ASSY |
| Парткод: | A0HTR70300 |
| Деталь: | MOTOR ASSY |
| Парткод: | A0HTR71000 |
| Деталь: | COVER |
| Парткод: | A0P0132400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J136911 |
| Деталь: | FAN MOTOR |
| Парткод: | 4556M10000 |
| Деталь: | SEAL |
| Парткод: | A00J143000 |
| Деталь: | Dust-proof Filter |
| Парткод: | A00J141200 |
| Деталь: | SEAL |
| Парткод: | A0P0143600 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J143500 |
| Деталь: | Main power assy 100V |
| Парткод: | A0P0R70411 |
| Деталь: | Main power assy 200V |
| Парткод: | A0P0R70511 |
| Деталь: | MOTOR ASSY |
| Парткод: | 4037R70900 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J710200 |
| Деталь: | GEAR 16/64T |
| Парткод: | 4025490601 |
| Деталь: | Gear 16/40T |
| Парткод: | 4025490701 |
| Деталь: | GEAR 12/40T |
| Парткод: | 4025491001 |
| Деталь: | Arm /Front |
| Парткод: | A0P0710600 |
| Деталь: | WASHER |
| Парткод: | 4004472202 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J710800 |
| Деталь: | GEAR 15T |
| Парткод: | 4025490801 |
| Деталь: | 2ND TRANSFER RETRACTION DRIVE |
| Парткод: | A00JR7AU00 |
| Деталь: | GEAR 15T |
| Парткод: | 4025490901 |
| Деталь: | PIN |
| Парткод: | 4036491101 |
| Деталь: | SHAFT |
| Парткод: | 4025470902 |
| Деталь: | WASHER |
| Парткод: | 4004472301 |
| Деталь: | ARM |
| Парткод: | 4036471201 |
| Деталь: | TORSION SPRING |
| Парткод: | 4025472501 |
| Деталь: | Cam /1 |
| Парткод: | A00J711400 |
| Деталь: | CAM |
| Парткод: | 4004471002 |
| Деталь: | PIN |
| Парткод: | 1144520001 |
| Деталь: | Conveyance Wiring |
| Парткод: | A00JN11001 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J710700 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | BUSHING |
| Парткод: | 4036473001 |
| Деталь: | TORSION SPRING |
| Парткод: | 4025471902 |
| Деталь: | Arm /Rear |
| Парткод: | A0P0710501 |
| Деталь: | DETECTING PLATE |
| Парткод: | 4025472001 |
| Деталь: | Support Shaft |
| Парткод: | A00J710400 |
| Деталь: | Cover /Middle |
| Парткод: | A00J598101 |
| Деталь: | HOLDER |
| Парткод: | A00J586400 |
| Деталь: | Pressure Holder |
| Парткод: | A00J593500 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J593900 |
| Деталь: | FRAME / BYPASS (FRONT) |
| Парткод: | A00JR7AP00 |
| Деталь: | Bypass Cover /Front |
| Парткод: | A00J598200 |
| Деталь: | PLATE SPRING |
| Парткод: | A00J588800 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J594800 |
| Деталь: | Mounting Plate /F |
| Парткод: | A00J599200 |
| Деталь: | LOCK LEVER |
| Парткод: | A00J598401 |
| Деталь: | HOLDER |
| Парткод: | A00J594900 |
| Деталь: | SHAFT |
| Парткод: | A00J585500 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J585401 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J585601 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J596602 |
| Деталь: | ROLL |
| Парткод: | A00J588300 |
| Деталь: | Fixing Plate |
| Парткод: | A00J588200 |
| Деталь: | Positioning Shaft |
| Парткод: | A00J594701 |
| Деталь: | Hold Holder |
| Парткод: | A00J586700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J599800 |
| Деталь: | Detecting Shaft |
| Парткод: | A00J585700 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J599500 |
| Деталь: | Set Actuator |
| Парткод: | A00J598800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J585100 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J586600 |
| Деталь: | FRAME |
| Парткод: | A00J590201 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J599700 |
| Деталь: | SEAL |
| Парткод: | A00J588601 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | Protection Cover |
| Парткод: | A0P0141300 |
| Деталь: | Mounting Plate /ASSY |
| Парткод: | A0P0131500 |
| Деталь: | SPACER |
| Парткод: | V502010036 |
| Деталь: | Guide Cover |
| Парткод: | A0P0135700 |
| Деталь: | Power source |
| Парткод: | A2WUM40000 |
| Деталь: | Power source |
| Парткод: | A0P0M40107 |
| Деталь: | Power source |
| Парткод: | A2WVM40000 |
| Деталь: | Power source |
| Парткод: | A0P1M40104 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J132500 |
| Деталь: | FAN MOTOR |
| Парткод: | A00JM14100 |
| Деталь: | COVER |
| Парткод: | A0P0131301 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0149000 |
| Деталь: | SEAL |
| Парткод: | A0P0148900 |
| Деталь: | COVER |
| Парткод: | A0P0138400 |
| Деталь: | Protection Seal |
| Парткод: | A0P0149800 |
| Деталь: | Cover Holder |
| Парткод: | A0P0134300 |
| Деталь: | Paper feed Cover |
| Парткод: | A00J603800 |
| Деталь: | COLLAR |
| Парткод: | 1134304101 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J619101 |
| Деталь: | Conveyance Roller |
| Парткод: | A00J601111 |
| Деталь: | SHAFT |
| Парткод: | 1134304202 |
| Деталь: | ACTUATOR |
| Парткод: | A00J604002 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J615800 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J603900 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | BUSHING |
| Парткод: | A00J663200 |
| Деталь: | BALL BEARING |
| Парткод: | A00J617800 |
| Деталь: | Guide Assy draw /2 |
| Парткод: | A00J603700 |
| Деталь: | Regulating Plate /Front |
| Парткод: | A00J600600 |
| Деталь: | CLUTCH |
| Парткод: | A00J563500 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | Paper feed Shaft |
| Парткод: | A00J604200 |
| Деталь: | SHAFT |
| Парткод: | A00J603000 |
| Деталь: | Level Actuator /1 |
| Парткод: | A00J602401 |
| Деталь: | WASHER |
| Парткод: | A0P0664000 |
| Деталь: | Pulley 14T |
| Парткод: | A00J602800 |
| Деталь: | Timing belt 102L |
| Парткод: | A00J602700 |
| Деталь: | Paper feed Base frame /1 |
| Парткод: | A00J600104 |
| Деталь: | Slide Shaft Holder |
| Парткод: | A03U812800 |
| Деталь: | Paper feed Shaft /2 |
| Парткод: | A00J603500 |
| Деталь: | SHAFT STOPPER |
| Парткод: | 55VA42120 |
| Деталь: | PAPER FEED DRIVING CLUTCH |
| Парткод: | 56AA82012 |
| Деталь: | BALL BEARING |
| Парткод: | A00J617900 |
| Деталь: | HANDLE |
| Парткод: | A00J618300 |
| Деталь: | AUXILIARY PART |
| Парткод: | A00J603101 |
| Деталь: | Auxiliary Part /2 |
| Парткод: | A00J619400 |
| Деталь: | PAPER FEED REGULATING BLOCK |
| Парткод: | 56AA40380 |
| Деталь: | Regulating Plate /Rear |
| Парткод: | A00J600400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0602500 |
| Деталь: | COUPLING |
| Парткод: | A00J600500 |
| Деталь: | Wiring Cover |
| Парткод: | A00J618000 |
| Деталь: | PFU Relay harness /4 |
| Парткод: | A00JN11D01 |
| Деталь: | WASHER |
| Парткод: | A00J660700 |
| Деталь: | WASHER |
| Парткод: | A00J660800 |
| Деталь: | 1500-sheet paper feed assy |
| Парткод: | A0P0R72222 |
| Деталь: | 2ND TRANSFER ROLLER ASSY |
| Парткод: | AOPOR71900 |
| Деталь: | TRANSFER UNIT |
| Парткод: | A2WUR70600 |
| Деталь: | Paper feed Door /Lower |
| Парткод: | A00J571701 |
| Деталь: | Attaching Cover |
| Парткод: | A00J574600 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J566600 |
| Деталь: | Lock Claw /Front |
| Парткод: | A00J573701 |
| Деталь: | ROLL |
| Парткод: | 4030312201 |
| Деталь: | PULLING SPRING /LOWER |
| Парткод: | A00J574500 |
| Деталь: | Idler Shaft |
| Парткод: | A00J574100 |
| Деталь: | Guide Plate /Lower |
| Парткод: | A0P0571900 |
| Деталь: | Lock Catch |
| Парткод: | A00J574201 |
| Деталь: | HOLDING GUIDE |
| Парткод: | A0P0567600 |
| Деталь: | BUSHING |
| Парткод: | 4131300301 |
| Деталь: | SHAFT STOPPER 4 |
| Парткод: | 56AA40490 |
| Деталь: | PHOTO INTERRUPTER |
| Парткод: | A108R90000 |
| Деталь: | ACTUATOR |
| Парткод: | 4030301612 |
| Деталь: | GUIDE PLATE |
| Парткод: | A00J572300 |
| Деталь: | GEAR 30T |
| Парткод: | 4425301301 |
| Деталь: | CLUTCH |
| Парткод: | A00J563500 |
| Деталь: | ROLLER |
| Парткод: | A00J563600 |
| Деталь: | Shaft /P |
| Парткод: | A00J564000 |
| Деталь: | GEAR 29T |
| Парткод: | 4030300801 |
| Деталь: | Paper feed Holder |
| Парткод: | A00J560100 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J560302 |
| Деталь: | BUSHING |
| Парткод: | 1065308601 |
| Деталь: | SHAFT |
| Парткод: | 4040309701 |
| Деталь: | GEAR 32T |
| Парткод: | 4425301601 |
| Деталь: | Paper feed Shaft |
| Парткод: | A0P0560200 |
| Деталь: | Release Lever |
| Парткод: | A00J567300 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J566801 |
| Деталь: | SHAFT |
| Парткод: | A00J566500 |
| Деталь: | Paper feed Frame |
| Парткод: | A00J560400 |
| Деталь: | CONVEYANCE DRIVE CLUTCH |
| Парткод: | 57AA82030 |
| Деталь: | FRAME / PAPER FEED 2 |
| Парткод: | A00JR7AE00 |
| Деталь: | Stopper Door |
| Парткод: | A00J573601 |
| Деталь: | Guide Plate /Upper |
| Парткод: | A0P0571800 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J573900 |
| Деталь: | Lock Claw /Rear |
| Парткод: | A00J573801 |
| Деталь: | Paper feed 2 assy |
| Парткод: | A0P0R72100 |
| Деталь: | Conveyance Cover /Right |
| Парткод: | A00J705114 |
| Деталь: | HOLDER |
| Парткод: | 4036359702 |
| Деталь: | Conveyance Relay harness /1 |
| Парткод: | A00JN11101 |
| Деталь: | COLLAR |
| Парткод: | 4036365901 |
| Деталь: | COMPRESSING SPRING |
| Парткод: | A00J706800 |
| Деталь: | PRESSURE SPRING |
| Парткод: | 4025353401 |
| Деталь: | Reinforce Plate /Front |
| Парткод: | A00J705700 |
| Деталь: | SHOULDER SCREW |
| Парткод: | A00J705800 |
| Деталь: | Guide Film |
| Парткод: | A00J705200 |
| Деталь: | Open/close Lever /Right |
| Парткод: | A00J706200 |
| Деталь: | Lock Lever /F |
| Парткод: | A00J706500 |
| Деталь: | TORSION SPRING |
| Парткод: | 4036359002 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J709400 |
| Деталь: | LABEL HI-TEMP CAUTION |
| Парткод: | 4138586601 |
| Деталь: | LABEL |
| Парткод: | A00J941400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J706300 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J709500 |
| Деталь: | Holding Lever |
| Парткод: | A0P0705300 |
| Деталь: | TORSION SPRING |
| Парткод: | A00J706000 |
| Деталь: | Support Plate |
| Парткод: | A00J706700 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313100072 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J706400 |
| Деталь: | CONTACT |
| Парткод: | A0P0708800 |
| Деталь: | CONTACT |
| Парткод: | A0P0712200 |
| Деталь: | RESISTOR |
| Парткод: | 9454407602 |
| Деталь: | GROUND PLATE |
| Парткод: | A00J708100 |
| Деталь: | CONTACT |
| Парткод: | A00J708400 |
| Деталь: | CONTACT |
| Парткод: | A00J708300 |
| Деталь: | CONTACT |
| Парткод: | A00J708900 |
| Деталь: | CONTACT |
| Парткод: | A00J708700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0709000 |
| Деталь: | CONTACT |
| Парткод: | A0P0709100 |
| Деталь: | Conveyance Duct |
| Парткод: | A00J705600 |
| Деталь: | REINFORCE PLATE |
| Парткод: | A00J708000 |
| Деталь: | Lock Lever /R |
| Парткод: | A00J706600 |
| Деталь: | PROTECTION PART |
| Парткод: | A00J709300 |
| Деталь: | Support Shaft |
| Парткод: | A00J707300 |
| Деталь: | Wiring Cover |
| Парткод: | A00J705900 |
| Деталь: | ROLL |
| Парткод: | A0P0709600 |
| Деталь: | CUSHION |
| Парткод: | A00J815711 |
| Деталь: | CONTACT |
| Парткод: | A0P0708200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0125200 |
| Деталь: | Protection Sheet /Black |
| Парткод: | A00J121700 |
| Деталь: | Developing Relay harness |
| Парткод: | A2WUN12700 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A00J155300 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0144000 |
| Деталь: | DUCT |
| Парткод: | A0P0155100 |
| Деталь: | SEAL |
| Парткод: | A0P0159100 |
| Деталь: | FAN MOTOR |
| Парткод: | 9313110033 |
| Деталь: | MOTOR ASSY |
| Парткод: | A0P0R75200 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0109100 |
| Деталь: | COLLAR |
| Парткод: | A00J123400 |
| Деталь: | MOUNTING PLATE |
| Парткод: | A0P0125100 |
| Деталь: | PHOTOINTERRUPTER |
| Парткод: | A108M50100 |
| Деталь: | GEAR 22T |
| Парткод: | A00J123300 |
| Деталь: | COUPLING |
| Парткод: | A00J123200 |
Коды ошибок
C0104
C0105
C0202
C0204
C0206
C0208
C0216
C0301
C0351
C1003
C1004
C1005
C1081
C1102
C1103
C1104
C1105
C1106
C1109
C1110
C1112
C1113
C1114
C1115
C1116
C1124
C1125
C1127
C1130
C1131
C1132
C1133
C1134
C1135
C1136
C1140
C1141
C1142
C1143
C1144
C1145
C1150
C1151
C1152
C1153
C1156
C1157
C1158
C1182
C1183
C1190
C1194
C11A1
C11A2
C11A7
C11B0
C11B2
C11B5
C11C0
C11E0
C11E1
C11E2
C2101
C2151
C2152
C2163
C2204
C2257
C2258
C2259
C225A
C225B
C225C
C2350
C2353
C2354
C2557
C2558
C255C
C2564
C2650
C2654
C2A14
C2A24
C3101
C3102
C3201
C3202
C3303
C3305
C3424
C3425
C3721
C3722
C3724
C3725
C3822
C3824
C3825
C3921
C3922
C3924
C3925
C392A
C3B02
C3B03
C3B05
C3B06
C3B07
C3B08
C4101
C4301
C4501
C5104
C5105
C5304
C5306
C5351
C5354
C5356
C5370
C5372
C6001
C6002
C6102
C6103
C6301
C6704
C6751
C6752
C6901
C6902
C6903
C6F01
C8101
C8102
C8103
C8104
C8106
C8302
C8401
C9401
C9402
CA051
CA052
CA053
CC001
CC151
CC152
CC153
CC155
CC156
CC157
CC158
CC159
CC15A
CC15B
CC163
CC164
CC165
CC170 ... CC184
CC185
CC186
CC190
CC191
CD002
CD004
CD00F
CD010
CD011
CD020
CD030
CD041 ... CD046
CD047 ... CD04B
CD201
CD202
CD203
CD211
CD212
CD231
CD241
CD242
CD261
CD271
CD272
CD300 ... CD399
CD401 ... CD407
CE001 ... CE007
CE002
CEEE1
CEEE2
CEEE3
CFB00 ... CFFA0
Описание
| Error code: | C0104 |
| Description: | Tray 3/4 feeder transportation motor failure to turn The lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • LCC transport motor (M25) • Paper feed/transport drive board (PFTDB) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M25-PFTDB CN17 for proper connection and correct as necessary. 2 Check the connector of M25 for proper drive coupling and correct as necessary. 3 M25 operation check PFTDB CN17-1 to 7 11-X. 4 Replace M25. 5 PFTDB ICP6 conduction check. 6 Replace PFTDB. 7 Replace PRCB. |
| Error code: | C0105 |
| Description: | Tray 3/4 feeder transportation motor turning at abnormal timing The lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • LCC transport motor (M25) • Paper feed/transport drive board (PFTDB) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M25-PFTDB CN17 for proper connection and correct as necessary. 2 Check the connector of M25 for proper drive coupling and correct as necessary. 3 M25 operation check PFTDB CN17-1 to 7 11-X. 4 Replace M25. 5 PFTDB ICP6 conduction check. 6 Replace PFTDB. 7 Replace PRCB. |
| Error code: | C0202 |
| Description: | Magenta PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 1 upper limit sensor (PS6) • Tray 1 lift-up motor (M6) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0204 |
| Description: | Yellow PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 2 upper limit sensor (PS14) • Tray 2 lift-up motor (M8) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0206 |
| Description: | Black PC Drum Charge Corona malfunction The SCD signal remains inactive for a continuous 1sec. period while charge corona is being output (i.e., the Remote signal is being turned ON). |
| Causes: | • Tray 3 upper limit sensor (PS22) • Tray 3 lift-up motor (M23) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Imaging Unit contact failure YES: Correct or clean Imaging Unit contact. 2 High Voltage Unit 1 contact failure YES: Correct or clean High Voltage Unit 1 contact. 3 After corona output has been turned ON: Cyan (C0200): The voltage across PJ9I-10 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Magenta (C0202): The voltage across PJ9I-8 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Yellow (C0204): The voltage across PJ9I-6 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. Bk (C0206): The voltage across PJ9I-12 on Master Board and GND is DC 24 V when the output is turned OFF and DC 0 V when the output is turned ON. YES: Change High Voltage Unit 1. NO: Change Master Board.oard. |
| Error code: | C0208 |
| Description: | Tray 5 feeder up/down abnormality |
| Causes: | • Tray 4 upper limit sensor (PS27) • Tray 4 lift-up motor (M24) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Error code: | C0216 |
| Description: | LCT up/down abnormality (When LU-205 or LU-303 is installed). The LU upper limit sensor (PS2) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. |
| Causes: | • LU upper limit sensor (PS2) • LU lift-up motor (M1) • LU drive board (LUDB) |
| Remedy: | 1. Check the connector between M1-LUDB CN3 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-relay CN406-LUDB CN5 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: LUDB CN5-3 (ON) • Location of electrical component: LU-205/LU-303 4-G 5. M1 operation check • Control signal: LUDB CN3-4 (ON) • Location of electrical component: LU-205/LU-303 3-G 6. Replace M1. 7. Replace LUDB. (LU-205/LU-303) NOTICE • Link to the wiring diagram ( N.3.1 LU-205) • Link to the wiring diagram ( N.3.2 LU-303) |
| Error code: | C0301 |
| Description: | Suction fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Suction fan (FM1) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1 Check the FM8 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM8 operation check PRCB CN3PRCB-2 (ON) PRCB CN3PRCB-3 (LOCK) D-4 to 5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C0351 |
| Description: | Paper cooling fan/in`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Paper cooling fan/in (FM12) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM12-relay CN325-MFPB CN27E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM12 operation check • Control signal: MFPB CN27E<B>-6 (LOCK) • Location of electrical component: 15-C 4. Replace FM12. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C1003 |
| Description: | PK communication error <When FS-535+PK-521 is installed> When a communication error is detected between the FS control board (FSCB) and the punch control board (PKCB). |
| Causes: | • Punch control board (PKCB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace PKCB. 4 Replace FSCB. |
| Error code: | C1004 |
| Description: | FNS communication error |
| Causes: | FS control board (FSCB) |
| Error code: | C1005 |
| Description: | ZU communication error When the ZU control board (ZUCB) is receiving data, a communication error is detected. |
| Causes: | ZU control board (ZUCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace ZUCB |
| Error code: | C1081 |
| Description: | SD communication error <When FS-534+SD-511 is installed> When a communication error is detected between the FS control board (FSCB) and the SD control board (SDDB). |
| Causes: | • SD drive board (SDDB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace SDDB. 4 Replace FSCB. |
| Error code: | C1102 |
| Description: | Main tray up/down motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • While the exit tray is being lifted, the main tray upper position sensor (PS26/PS27) is not turned ON (blocked) and the main tray upper position detect switch (SW2) is not turned ON, even after the main tray up/down motor (M11) turns by the set number of times. • While the exit tray is being lowered, the main tray full detection sensor (PS29) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M11) is turned ON. <When FS-537 or FS-537SD is installed> • The main tray lift up detection sensor (PS16/PS17) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/ down motor (M6) is turned ON. • The main tray full detection sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the main tray up/down motor (M6) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Main tray up/down motor (M11) • Main tray upper position sensor/R (PS26) • Main tray upper position sensor/F (PS27) • Main tray full detection sensor (PS29) • Main tray upper position detect switch (SW2) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Main tray up/down motor (M6) • Main tray lift up detection sensor/F (PS16) • Main tray lift up detection sensor/R (PS17) • Main tray full detection sensor (PS12) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M11-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M11 for proper drive coupling, and correct as necessary. 3. Check the connector between PS26-relay CN1-FSCB J14 for proper connection and correct as necessary. 4. Check the connector between PS27-relay CN1-FSCB J14 for proper connection and correct as necessary. 5. Check the connector between PS29-relay CN2-FSCB J14 for proper connection and correct as necessary. 6. Check the connector between SW2-FSCB J10 for proper connection and correct as necessary. 7. PS26 I/O check, sensor check • Control signal: FSCB J14<A>-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-C 8. PS27 I/O check, sensor check • Control signal: FSCB J14<B>-6 (ON) • Location of electrical component: FS-536/FS-536SD 3-C 9. PS29 I/O check, sensor check • Control signal: FSCB J14<A>-8 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 10. SW2 operation check • Control signal: FSCB J10-1 to 2 • Location of electrical component: FS-536/FS-536SD 15-K 11. M11 operation check • Control signal: FSCB J9<A>-9 to 10 • Location of electrical component: FS-536/FS-536SD 12-C 12. Replace M11. 13. FSCB F2 conduction check 14. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M6-FSCB J23 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS16-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 4. Check the connector between PS17-relay CN10<B>-FSCB J20 for proper connection and correct as necessary. 5. Check the connector between PS12-relay CN9-FSCB J19 for proper connection and correct as necessary. 6. PS16 I/O check, sensor check • Control signal: FSCB J20<B>-4 (ON) • Location of electrical component: FS-537/FS-537SD 11 to 12-D 7. PS17 I/O check, sensor check • Control signal: FSCB J20<B>-7 (ON) • Location of electrical component: FS-537/FS-537SD 12-D 8. PS12 I/O check, sensor check • Control signal: FSCB J19-7 (ON) • Location of electrical component: FS-537/FS-537SD 10-D 9. M6 operation check • Control signal: FSCB J23-1 to 11 • Location of electrical component: FS-537/FS-537SD 13-D 10. Replace M6. 11. FSCB F3 conduction check 12. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1103 |
| Description: | Alignment motor/Front’s drive malfunction. <When FS-536 or FS-536SD is installed> • The alignment plate/F home sensor (PS12) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS12) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M7) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The alignment plate/F home sensor (PS9) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate/F home sensor (PS9) is not turned ON (blocked) after the set period of time has elapsed after the alignment motor/Front (M14) is turned ON to return the plate to the home position. • The alignment plate/F does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Alignment motor/Front (M7) • Alignment plate/F home sensor (PS12) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Alignment motor/Front (M14) • Alignment plate/F home sensor (PS9) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M7-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS12-FSCB J4 for proper connection and correct as necessary. 4. PS12 I/O check, sensor check • Control signal: FSCB J4<B>-4 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M7 operation check • Control signal: FSCB J4<A>-5 to 8 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M7. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M14-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M14 for proper drive coupling and correct as necessary. 3. Check the connector between PS9-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS9 I/O check, sensor check • Control signal: FSCB J18-10 (ON) • Location of electrical component: FS-537/FS-537SD 6-D 5. M14 operation check • Control signal: FSCB J18-1 to 4 • Location of electrical component: FS-537/FS-537SD 6-D 6. Replace M14. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1104 |
| Description: | Stacker plate drive motor`s malfunction. <When FS-537 or FS-537SD is installed> The stacker plate home sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stacker plate drive motor (M3) is turned ON. |
| Causes: | • Stacker plate drive motor (M3) • Stacker plate home sensor (PS30) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M3-relay CN1<B>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS30-relay CN2-relay CN1<B>-FSCB J22 for proper connection and correct as necessary. 4. PS30 I/O check, sensor check • Control signal: FSCB J22<B>-10 (ON) • Location of electrical component: FS-537/FS-537SD 3-D 5. M3 operation check • Control signal: FSCB J22<B>1 to 2 • Location of electrical component: FS-537/FS-537SD 2-D 6. Replace M3. 7. Replace FSCB. NOTICE: • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1105 |
| Description: | Bundle eject motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • The gripper home position sensor (PS18) is not turned ON (unblocked) even after the set period of time has elapsed after the gripper position detection sensor (PS19) turns OFF (block). • The gripper position detection sensor (PS19) is not turned OFF (blocked) even after the set period of time has elapsed after PS19 turns ON (unblock). • The gripper position detection sensor (PS19) is not turned ON (unblocked) even after the set period of time has elapsed after the gripper home position sensor (PS18) turns OFF (block). • The gripper home position sensor (PS18) is not turned OFF (blocked) even after the set period of time has elapsed after the bundle eject motor (M10) is energized. • The gripper home position sensor (PS18) and the gripper position detection sensor (PS19) is turned ON (unblocked) at the same time. <When FS-537 or FS-537SD is installed> The gripper home position sensor (PS3) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed after the bundle eject motor (M1) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Bundle eject motor (M10) • Gripper home position sensor (PS18) • Gripper position detection sensor (PS19) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Bundle eject motor (M1) • Gripper home position sensor (PS3) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M10-relay CN7<A>-FSCB J13 for proper connection and correct as necessary. 2. Check the connector of M10 for proper drive coupling, and correct as necessary. 3. Check the connector between PS18-relay CN7<A>-FSCB J13 for proper connection and correct as necessary. 4. Check the connector between PS19-relay CN8<B>-FSCB J12 for proper connection and correct as necessary. 5. PS18 I/O check, sensor check • Control signal: FSCB J13-13 (ON) • Location of electrical component: FS-536/FS-536SD 8-C 6. PS19 I/O check, sensor check • Control signal: FSCB J12-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 7. M10 operation check • Control signal: FSCB J13-1 to 2 • Location of electrical component: FS-536/FS-536SD 9-C 8. Replace M10. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M1-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS3-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 4. PS3 I/O check, sensor check • Control signal: FSCB J22<A>-13 (ON) • Location of electrical component: FS-537/FS-537SD 2-D 5. M1 operation check • Control signal: FSCB J22<A>-1 to 2 • Location of electrical component: FS-537/FS-537SD 1-D 6. Replace M1. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1106 |
| Description: | Stapler movement motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the side stapler movement motor (M13) turned ON. • The stapler does not reach the specified position within the set period of time. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M19) turned ON. • The stapler does not reach the specified position within the set period of time. |
| Causes: | <When FS-536 or FS-536SD is installed> • Side stapler movement motor (M13) • Stapler home position sensor (rear) (PS23) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler movement motor (M19) • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M13-relay CN3-FSCB J11 for proper connection, and correct as necessary. 2. Check the connector of M13 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 5. M13 operation check • Control signal: FSCB J11<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 4-C 6. Replace M13. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M19-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of M19 for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. PS18 I/O check, sensor check • Control signal: FSCB J16-9 (ON) • Location of electrical component: FS-537/FS-537SD15-D 6. PS19 I/O check, sensor check • Control signal: FSCB J16-6 (ON) • Location of electrical component: FS-537/FS-537SD 15-D 7. M19 operation check • Control signal: FSCB J17-10 to 13 • Location of electrical component: FS-537/FS-537SD 14-D 8. Replace M19. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1109 |
| Description: | Stapler motor’s malfunction. <When FS-536 or FS-536SD is installed> • The stapler home position sensor (rear) (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler motor (M14) turned ON. • The stapler position sensor (center) (PS24) is turned ON (blocked), when the stapler motor (M14) is running. <When FS-537 or FS-537SD is installed> • The stapler home position sensor (PS18/PS19) is not turned (unblocked) or ON (blocked) even after the set period of time has elapsed after the stapler movement motor (M5) turned ON. • The stapler position sensor (center) (PS20) is turned ON (blocked), when the stapler motor (M5) is running. |
| Causes: | <When FS-536 or FS-536SD is installed> • Stapler unit • Stapler home position sensor (rear) (PS23) • Stapler position sensor (center) (PS24) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Stapler unit • Stapler home position sensor (corner) (PS18) • Stapler home position sensor (rear) (PS19) • Stapler position sensor (center) (PS20) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between the stapler unit-relay CN4-FSCB J11 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. Check the connector between PS24-relay CN3-FSCB J11 for proper connection and correct as necessary. 5. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-C 6. PS24 I/O check, sensor check • Control signal: FSCB J11<B>-6 • Location of electrical component: FS-536/FS-536SD 5-C 7. Replace the stapler unit. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between the stapler unit-FSCB J17 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS18-FSCB J16 for proper connection and correct as necessary. 4. Check the connector between PS19-FSCB J16 for proper connection and correct as necessary. 5. Check the connector between PS20-FSCB J16 for proper connection and correct as necessary. 6. PS18 I/O check, sensor check • Control signal: FSCB J16-9 • Location of electrical component: FS-537/FS-537SD 15-D 7. PS19 I/O check, sensor check • Control signal: FSCB J16-6 • Location of electrical component: FS-537/FS-537SD 15-D 8. PS20 I/O check, sensor check • Control signal: FSCB J16-3 • Location of electrical component: FS-537/FS-537SD 15-D 9. Replace the stapler unit. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1110 |
| Description: | PF lift motor 2 error |
| Causes: | [The left cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because of one of the phenomena below. 1. PF lift sensor 2 does not turn on when passing 23s while PF lift motor 2 turns on for the first time after inserting the cassette. 2. PF lift sensor 2 does not turn on when passing 2s while PF lift motor 2 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 2 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 2 - PF main PWB Wiring diagram 4 Replacing PF lift motor 2 PF lift motor 2 is faulty. Replace PF lift motor 2. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •PF lift sensor 2 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 2 is not properly attached or faulty. Reattach PF lift sensor 2. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1112 |
| Description: | Stapler motor`s drive malfunction. <When FS-536SD or FS-537SD is installed> • The stapler home sensor is not turned ON even after the set period of time has elapsed while the stapler motor is energized. • The stapler home sensor is not turned OFF even after the set period of time has elapsed after the stapler home sensor is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Staple unit • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between the staple unit-SDCB J4 for proper connection and correct as necessary. 2. Check the connector of the staple unit for proper drive coupling and correct as necessary. 3. Replace the staple unit. (FS-536SD/FS-537SD) 4. Replace SDCB. (FS-536SD/FS-537SD) 5. Replace FSCB. (FS-536SD/FS-537SD) |
| Error code: | C1113 |
| Description: | Stopper drive motor`s malfunction. <When FS-536SD or FS-537SD is installed> The stopper home sensor (PS6) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Stopper drive motor (M4) • Stopper home sensor (PS6) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M4-SDCB J10 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-SDCB J10 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: SDCB J10-5 (ON) • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 2-P 5. M4 operation check • Control signal: SDCB J10-6 to 9 • Location of electrical component: FS-536/FS-536SD 2-P, FS-537/FS-537SD 1-P 6. Replace M4. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1114 |
| Description: | Alignment motor’s malfunction. <When FS-536SD or FS-537SD is installed> The alignment home sensor (PS4) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the alignment motor (M3) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Alignment motor (M3) • Alignment home sensor (PS4) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M3-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS4-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS4 I/O check, sensor check • Control signal: SDCB J7-6 (ON) • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 5. M3 operation check • Control signal: SDCB J7-7 to 10 • Location of electrical component: FS-536/FS-536SD 6-P, FS-537/FS-537SD 5-P 6. Replace M3. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1115 |
| Description: | Center fold knife motor`s malfunction. <When FS-536SD or FS-537SD is installed> The center fold knife home sensor (PS8) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON. |
| Causes: | <When FS-536SD or FS-537SD is installed> • Center fold knife motor (M9) • Center fold knife home sensor (PS8) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M9-SDCB J11 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS8-relay CN26 (FS-536SD), CN29 (FS-537SD)-SDCB J7 for proper connection and correct as necessary. 4. PS8 I/O check, sensor check • Control signal: SDCB J7-3 (ON) • Location of electrical component: FS-536/FS-536SD 7-P, FS-537/FS-537SD 6-P 5. M9 operation check • Control signal: SDCB J11-11 to 20 • Location of electrical component: FS-536/FS-536SD 2-L, FS-537/FS-537SD 1-K 6. Replace M9. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1116 |
| Description: | Center-staple transfer motor malfunction <When FS-526+SD-508 is installed> • The transport motor (M33) does not reach the specified speed even after the set period of time has elapsed after it starts to operate. <When FS-527+SD-509 is installed> • The center fold roller motor (M25) does not reach the specified speed even after the set period of time has elapsed after it starts to operate. |
| Causes: | When FS-526+SD-508 is installed: Transport motor (M33) SD drive board (SDDB) FS control board (FSCB). When FS-527+SD-509 is installed: Center fold roller motor (M25) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | When FS-526+SD-508 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M33 for proper drive coupling, and correct as necessary. - - 3 M33 operation check SDDB CN409-1 to 11 SD-508 K-5 4 Change M33 - - 5 SDDB ICP5 conduction check - - 6 Change SDDB - - 7 Change FSCB. When FS-527+SD-509 is installed: 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M25 for proper drive coupling, and correct as necessary. - - 3 M25 operation check SDDB PJ4-1 to 11 SD-509 B-3 4 Change M25 - - 5 Change SDDB - - 6 Change FSCB |
| Error code: | C1124 |
| Description: | Tray lift motor /Lw`s drive malfunction. <When FS-537+PI-507 or FS-537SD+PI-507 is installed> The tray upper limit sensor /Lw (PS209) or tray lower limit sensor /Lw (PS210) is not turned ON (blocked) after the set period of time has elapsed after the tray lift motor /Lw (M202) is turned ON. |
| Causes: | • Tray lift motor /Lw (M202) • Tray upper limit sensor /Lw (PS209) • Tray lower limit sensor /Lw (PS210) • PI drive board (PIDB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M202-relay CN206-PIDB CN56 for proper connection and correct as necessary. 2. Check the connector of M202 for proper drive coupling and correct as necessary. 3. Check the connector between PS209-relay CN237-PIDB CN53 for proper connection and correct as necessary. 4. Check the connector between PS210-relay CN236-PIDB CN53 for proper connection and correct as necessary. 5. PS209 I/O check, sensor check • Control signal: PIDB CN53<A>-8 (ON) • Location of electrical component: PI-507 10-C 6. PS210 I/O check, sensor check • Control signal: PIDB CN53<A>-11 (ON) • Location of electrical component: PI-507 11-C 7. M202 operation check • Control signal: PIDB CN56-5 to 6 • Location of electrical component: PI-507 9-C 8. Replace M202. 9. Replace PIDB. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.6 PI-507) |
| Error code: | C1125 |
| Description: | Tray lift motor /Up`s drive malfunction. <When FS-537+PI-507 or FS-537SD+PI-507 is installed> The tray upper limit sensor /Up (PS205) or tray lower limit sensor /Up (PS204) is not turned ON (blocked) after the set period of time has elapsed after the tray lift motor /Up (M201) is turned ON. |
| Causes: | • Tray lift motor /Up (M201) • Tray upper limit sensor /Up (PS204) • Tray lower limit sensor /Up(PS205) • PI drive board (PIDB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M201-relay CN203-PIDB CN54 for proper connection and correct as necessary. 2. Check the connector of M201 for proper drive coupling and correct as necessary. 3. Check the connector between PS204-relay CN235-PIDB CN55 for proper connection and correct as necessary. 4. Check the connector between PS205-relay CN235-PIDB CN55 for proper connection and correct as necessary. 5. PS204 I/O check, sensor check • Control signal: PIDB CN55-8 (ON) • Location of electrical component: PI-507 8-C 6. PS205 I/O check, sensor check • Control signal: PIDB CN55-7 (ON) • Location of electrical component: PI-507 8-C 7. M201 operation check • Control signal: PIDB CN54-7 to 8 • Location of electrical component: PI-507 6 to 7-C 8. Replace M201. 9. Replace PIDB. 10. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.6 PI-507) |
| Error code: | C1127 |
| Description: | Punch oscillating motor’s drive malfunction. <When FS-537+PK-523 or FS-537SD+PK-523 is installed> The PKpunch oscillatinghome sensor (PS303) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the punch oscillating motor (M302) is energized. |
| Causes: | • Punch oscillating motor (M302) • PK punch oscillatinghome sensor (PS303) • Punch control board (PKCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M302-relay CN342-relay CN341-PKCB CN1 for proper connection and correct as necessary. 2. Check the connector of M302 for proper drive coupling and correct as necessary. 3. Check the connector between PS303-relay CN342-relay CN341-PKCB CN37 for proper connection and correct as necessary. 4. PS303 I/O check, sensor check • Control signal: PKCB CN37-2 (ON) • Location of electrical component: PK-523 5-C 5. M302 operation check • Control signal: PKCB CN1-1 to 6 • Location of electrical component: PK-523 5-C 6. Replace M302. 7. PKCB ICP2 conduction check. 8. Replace PKCB. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.4 PK-523) |
| Error code: | C1130 |
| Description: | PF right lift position problem (optional 3000-sheet paper feeder) Level switch 2 does not turn on within 30 s of PF lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 2. Defective PF lift motor 1. The PF right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 2. Check if YC5-7 on the PF main PWB goes low when level switch 2 is turned off. If not, replace PF lift switch 2. Defective PF lift motor 2. Check for continuity across the coil. If none, replace PF lift motor 2. The PF right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1131 |
| Description: | Folding guide motor’s drive malfunction. <When FS-537+ZU-609 or FS-537SD+ZU-609 is installed> The guide home sensor (PS500) is not turned ON (blocked) even after the set period of time has elapsed after the folding guide motor (M501) is turned ON. |
| Causes: | • Folding guide motor (M501) • Guide home sensor (PS500) • ZU drive board (ZUDB) |
| Remedy: | 1. Check the connector between M501-ZUDB CN6 for proper connection and correct as necessary. 2. Check the connector of M501 for proper drive coupling and correct as necessary. 3. Check the connector between PS500-ZUDB CN5 for proper connection and correct as necessary. 4. PS500 I/O check, sensor check • Control signal: ZUDB CN5-3 (ON) • Location of electrical component: ZU-609 3-B 5. M501 operation check • Control signal: ZUDB CN6-9 to 12 • Location of electrical component: ZU-609 2-B 6. Replace M501. 7. Replace ZUDB. NOTICE • Link to the wiring diagram ( N.3.5 ZU-609) |
| Error code: | C1132 |
| Description: | Punch drive motor’s drive malfunction. <When FS-536+PK-520 or FS-536SD+PK-520 is installed> The punch home sensor (PS1) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the punch drive motor (M1) is energized. <When FS-537+PK-523 or FS-537SD+PK-523 is installed> The PK punch home sensor/2(PS301) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the punch drive motor (M301) is energized. |
| Causes: | <When FS-536+PK-520 or FS-536SD+PK-520 is installed> • Punch drive motor (M1) • Punch home sensor (PS1) • FS control board (FSCB) <When FS-537+PK-523 or FS-537SD+PK-523 is installed> • Punch drive motor (M301) • PK punch home sensor/2(PS301) • Punch control board (PKCB) • FS control board (FSCB) |
| Remedy: | (a) When FS-536+PK-520 or FS-536SD+PK-520 is installed 1. Check the connector between M1-relay CN351-FSCB J7 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS1-FSCB J7 for proper connection and correct as necessary. 4. PS1 I/O check, sensor check • Control signal: FSCB J7-5 (ON) • Location of electrical component: FS-536/FS-536SD 13-K 5. M1 operation check • Control signal: FSCB J7-7 to 8 • Location of electrical component: FS-536/FS-536SD 13-K 6. Replace M1. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537+PK-523 or FS-537SD+PK-523 is installed 1. Check the connector between M301-relay CN351-PKCB CN35 for proper connection and correct as necessary. 2. Check the connector of M301 for proper drive coupling and correct as necessary. 3. Check the connector between PS301-PKCB CN36 for proper connection and correct as necessary. 4. PS301 I/O check, sensor check • Control signal: PKCB CN36-5 (ON) • Location of electrical component: PK-523 3-C 5. M301 operation check • Control signal: PKCB CN35-1 to 3 • Location of electrical component: PK-523 2-C 6. Replace M301. 7. Replace PKCB. 8. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.4 PK-523) |
| Error code: | C1133 |
| Description: | Pressure motor’s malfunction. <When FS-537+ZU-609 or FS-537SD+ZU-609 is installed> The press home sensor (PS502) is not turned ON (unblocked), or is not turned OFF (blocked) after it is turned ON (unblocked), even after the set period of time has elapsed after the pressure motor (M502) starts searching its home position |
| Causes: | • Pressure motor (M502) • Press home sensor (PS502) • ZU drive board (ZUDB) |
| Remedy: | 1. Check the connector between M502-ZUDB CN6 for proper connection and correct as necessary. 2. Check the connector of M502 for proper drive coupling and correct as necessary. 3. Check the connector between PS502-ZUDB CN5 for proper connection and correct as necessary. 4. PS502 I/O check, sensor check • Control signal: ZUDB CN5-6 (ON) • Location of electrical component: ZU-609 4-B 5. M502 operation check • Control signal: ZUDB CN6-7 (DRV) • Location of electrical component: ZU-609 2-B 6. Replace M502. 7. ZUDB ICP3 conduction check. 8. Replace ZUDB. NOTICE • Link to the wiring diagram ( N.3.5 ZU-609) |
| Error code: | C1134 |
| Description: | Main motor cooling fan’s drive malfunction <When FS-535+ZU-606 is installed> Even after the set period of time has elapsed after the main motor cooling fan (FM601) is turned ON, the FM601 EM signal is faulty and the fan is turned OFF; the signal is faulty after each of the following three trials. |
| Causes: | • Main motor cooling fan (FM601) • ZU control board (ZUCB) |
| Remedy: | 1 Check the connector between FM601-relay CN653- ZUCB CN11 for proper connection, and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM601 operation check ZUCB CN11-11 (DRV) ZU-606 8 to 9-C. 4 Replace FM601. 5 ZUCB ICP8 conduction check. 6 Replace ZUCB. |
| Error code: | C1135 |
| Description: | Punch motor’s drive malfunction <When FS-535+ZU-606 is installed> The punch motor (M604) is not turned OFF even after the set period of time has elapsed after it is turned ON. |
| Causes: | • Punch motor (M604) • ZU control board (ZUCB) |
| Remedy: | 1 Check the connector between M604-relay CN644- relay CN638-ZUCB CN11 for proper connection, and correct as necessary. 2 Check the connector of M604 for proper drive coupling, and correct as necessary. 3 M604 operation check ZUCB CN11-2 (DRV) ZU-606 7-C. 4 Replace M604. 5 ZUCB ICP10 conduction check. 6 Replace ZUCB. |
| Error code: | C1136 |
| Description: | Punch switchover motor’s drive malfunction <When FS-535+ZU-606 is installed> The punch switchover switch (MS601) is not turned OFF from the ON position, or not turned ON from the OFF position, even after the set period of time has elapsed after the punch switchover motor (M608) is turned ON. |
| Causes: | • Punch switchover motor (M608) • Punch switchover switch (MS601) • ZU control board (ZUCB) |
| Remedy: | 1 Check the connector between M608-relay CN633- relay CN638-ZUCB CN11 for proper connection, and correct as necessary. 2 Check the connector of M608 for proper drive coupling, and correct as necessary. 3 Check the connector between MS601-relay CN633- relay CN638-ZUCB CN11 for proper connection, and correct as necessary. 4 MS601 I/O check, sensor check ZUCB CN11-9 ZU-606 8-C. 5 M608 operation check ZUCB CN11-8 (DRV) ZU-606 7 to 8-C. 6 Replace M608. 7 ZUCB ICP9 conduction check. 8 Replace ZUCB. |
| Error code: | C1140 |
| Description: | PF lift motor error Object: Side feeder |
| Causes: | 1. The PF lift upper limit sensor does not turn on when passing 30s after cassette 5 is inserted. 2. The lock-up signal is detected for 200ms continuously during the PF lift motor operation. 3. The PF lift upper limit sensor does not turn on when passing 2s after the upper limit control when printing starts. |
| Remedy: | 1 Checking the bottom plate The bottom plate does not operate properly. Repair or replace the bottom plate when it does not move vertically. 2 Checking the drive gear The drive gear to lift up the bottom plate does not rotate properly. Check if the drive gears to lift up the bottom plate rotate smoothly or have no excessive load. And apply the grease to the frictional parts and fix the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor - PF main PWB Wiring diagram 4 Checking the PF lift motor The PF lift motor is faulty. Replace the PF lift motor. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift upper limit sensor - PF main PWB Wiring diagram 6 Checking the PF lift upper limit sensor The PF lift upper limit sensor is not properly attached or faulty. Reattach the PF lift upper limit sensor. Then, replace it if it is not fixed. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1141 |
| Description: | FNS paddle motor’s malfunction. <When FS-536 or FS-536SD is installed> The upper paddle home position detection sensor (PS14) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M5) is turning. <When FS-537 or FS-537SD is installed> The paddle home sensor (PS25) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M9) is turning. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS paddle motor (M5) • Upper paddle home position detection sensor (PS14) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • FNS paddle motor (M9) • Paddle home sensor (PS25) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M5-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS14-FSCB J4 for proper connection and correct as necessary. 4. PS14 I/O check, sensor check • Control signal: FSCB J4<B>-7 (ON) • Location of electrical component: FS-536/FS-536SD 15-C 5. M5 operation check • Control signal: FSCB J4<A>-9 to 12 • Location of electrical component: FS-536/FS-536SD 14-C 6. Replace M5. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M9-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS25-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 4. PS25 I/O check, sensor check • Control signal: FSCB J14<B>-10 (ON) • Location of electrical component: FS-537/FS-537SD 16-K to L 5. M9 operation check • Control signal: FSCB J14<B>-4 to 7 • Location of electrical component: FS-537/FS-537SD 17- K to L 6. Replace M9. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1142 |
| Description: | Paddle up/down motor`s drive malfunction. <When FS-537 or FS-537SD is installed> The paddle up/down home sensor (PS27) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the paddle up/down motor (M7) is energized. |
| Causes: | • Paddle up/down motor (M7) • Paddle up/down home sensor (PS27) • FS control board (FSCB) |
| Remedy: | (2) Procedure 1. Check the connector between M7-relay CN13<A>-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS27-relay CN13<A>-FSCB J14 for proper connection and correct as necessary. 4. PS27 I/O check, sensor check • Control signal: FSCB J14<A>-7 (ON) • Location of electrical component: FS-537/FS-537SD 18-K to L 5. M7 operation check • Control signal: FSCB J14<A>-1 to 4 • Location of electrical component: FS-537/FS-537SD 18-K to L 6. Replace M7. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1143 |
| Description: | Arm drive motor’s drive malfunction. <When FS-537 or FS-537SD is installed> The arm home position sensor (PS26) is not turned ON (unblocked) or OFF (blocked) even after the set period of time has elapsed while the arm drive motor (M8) is energized. |
| Causes: | • Arm drive motor (M8) • Arm home position sensor (PS26) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M8-relay CN13<A>-FSCB J14 for proper connection and correct as necessary. 2. Check the connector of M8 for proper drive coupling and correct as necessary. 3. Check the connector between PS26-relay CN13<B>-FSCB J14 for proper connection and correct as necessary. 4. PS26 I/O check, sensor check • Control signal: FSCB J14<B>-3 (ON) • Location of electrical component: FS-537/FS-537SD 17-K to L 5. M8 operation check • Control signal: FSCB J14<A>-8 to 11 • Location of electrical component: FS-537/FS-537SD 17-K to L 6. Replace M8. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1144 |
| Description: | Pre-eject drive motor’s drive malfunction. <When FS-536 or FS-536SD is installed> • The pre-eject home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the preeject drive motor (M9) is turned ON. • The pre-eject away sensor (PS22) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the preeject drive motor (M9) is turned ON. <When FS-537 or FS-537SD is installed> The trail edge stopper home sensor (PS31) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the pre-eject drive motor (M2) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Pre-eject drive motor (M9) • Pre-eject home sensor (PS21) • Pre-eject away sensor (PS22) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Pre-eject drive motor (M2) • Trail edge stopper home sensor (PS31) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M9-relay CN7<A>-FSCB J13 for proper connection, and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 4. Check the connector between PS22-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 5. PS21 I/O check, sensor check • Control signal: FSCB J12-6 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 6. PS22 I/O check, sensor check • Control signal: FSCB J12-9 (ON) • Location of electrical component: FS-536/FS-536SD 7-C 7. M9 operation check • Control signal: FSCB J13-3 to 4 • Location of electrical component: FS-536/FS-536SD 9-C 8. Replace M9. 9. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M2-relay CN1<A>-FSCB J22 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS31-relay CN2-relay CN1<B>-FSCB J22 for proper connection and correct as necessary. 4. PS31 I/O check, sensor check • Control signal: FSCB J22<B>-13 • Location of electrical component: FS-537/FS-537SD 3-D 5. M2 operation check • Control signal: FSCB J22<A>-3 to 4 • Location of electrical component: FS-537/FS-537SD 1-D 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1145 |
| Description: | Trailing edge stopper motor malfunction. <When FS-536 or FS-536SD is installed> The trailing edge stopper home position detection sensor (PS20) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor (M6) is turned ON. <When FS-537 or FS-537SD is installed> The trailing edge stopper home position detection sensor/F (PS10) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the trailing edge stopper motor/F (M12) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • Trailing edge stopper motor (M6) • Trailing edge stopper home position detection sensor (PS20) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Trail edge stopper motor/F (M12) • Trail edge stopper sensor/F (PS10) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M6-FSCB J5 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS20-relay CN19-FSCB J5 for proper connection and correct as necessary. 4. PS20 I/O check, sensor check • Control signal: FSCB J5-9 (ON) • Location of electrical component: FS-536/FS-536SD 15-K 5. M6 operation check • Control signal: FSCB J5-13 to 16 • Location of electrical component: FS-536/FS-536SD 15-K 6. Replace M6. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M12-relay CN5-FSCB J18 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS10-relay CN5-FSCB J18 for proper connection and correct as necessary. 4. PS10 I/O check, sensor check • Control signal: FSCB J18-13 (ON) • Location of electrical component: FS-537/FS-537SD 6 to 7-D 5. M12 operation check • Control signal: FSCB J18-14 to 17 • Location of electrical component: FS-537/FS-537SD 7-D 6. Replace M12. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1150 |
| Description: | Side feeder lift motor going down error (optional side feeder) • Lower limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding). This error is detected four times successively. |
| Causes: | Poor contact of lower limit detection switch connector terminals. Defective side feeder main PWB. Defective side feeder lift motor. |
| Remedy: | Poor contact of lower limit detection switch connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective side feeder main PWB. Replace the side feeder main PWB. Defective side feeder lift motor. Run maintenance mode U247 and measure the voltage between terminals YC5-A12 (side-feeder main circuit board) and YC6- B11. (Make sure all of LUSSW, UCSSW, LLSSW and RCSSW are off.) Despite either DC24V or DC-24V is observed but if the side-feeder lift motor does not operate, replace the side-feeder lift motor. |
| Error code: | C1151 |
| Description: | Center-staple stapler drive motor malfunction <When FS-526+SD-508 is installed> • The stapler home sensor (PS33) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple motor (M23) is turned ON. |
| Causes: | Center staple motor (M23) Stapler home sensor (PS33) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M23 for proper drive coupling, and correct as necessary. - - 3 PS33 I/O check, sensor check SDDB CN403-17 (ON) SD-508 C-10 4 M23 operation check SDDB CN406<A>-1 to 4 (ON) SD-508 K-8 5 Change M23 - - 6 SDDB ICP4 conduction check - - 7 Change SDDB - - 8 Change FSCB |
| Error code: | C1152 |
| Description: | Paper transport belt motor`s malfunction. <When FS-537SD is installed> Even after a predetermined period of time has elapsed since the paper transport belt motor (M34) starts operation, the lock signal is not set to L (turning). |
| Causes: | • Paper transport belt motor (M34) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M34-relay CN21-FSCB J24for proper connection and correct as necessary. 2. Check the connector of M34 for proper drive coupling and correct as necessary. 3. M34 operation check • Control signal: FSCB J24-1 to 11 • Location of electrical component: FS-537/FS-537SD 7-M 4. Replace M34. 5. Replace SDCB. 6. FSCB F4 conduction check 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1153 |
| Description: | Center-staple paddle up-down motor malfunction <When FS-526+SD-508 is installed> • The paddle home sensor/C (PS37) is turned neither ON nor OFF even after the set period of time has elapsed after the center staple paddle lift motor/C (M26) is turned ON. |
| Causes: | Center staple paddle lift motor/C (M26) Paddle home sensor/C (PS37) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M26 for proper drive coupling, and correct as necessary. - - 3 PS37 I/O check, sensor check SDDB CN406<A>-11 (ON) SD-508 K-9 4 M26 operation check SDDB CN406<A>-5 to 8 SD-508 K-8 5 Change M26 - - 6 SDDB ICP4 conduction check - - 7 Change SDDB - - 8 Change FSCB |
| Error code: | C1156 |
| Description: | SD paddle motor malfunction. <When FS-536SD or FS-537SD is installed> The paddle home sensor (PS5) is not turned OFF (blocked) or ON (unblocked) even after the set period of time has elapsed while the SD paddle motor (M7) is turning. |
| Causes: | <When FS-536SD or FS-537SD is installed> • SD paddle motor (M7) • Paddle home sensor (PS5) • SD control board (SDCB) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M7-SDCB J8 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS5-SDCB J8 for proper connection and correct as necessary. 4. PS5 I/O check, sensor check • Control signal: SDCB J8-3 (ON) • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 5. M7 operation check • Control signal: SDCB J8-4 to 7 • Location of electrical component: FS-536/FS-536SD 4-P, FS-537/FS-537SD 3-P 6. Replace M7. (FS-536SD/FS-537SD) 7. Replace SDCB. (FS-536SD/FS-537SD) 8. Replace FSCB. (FS-536SD/FS-537SD) NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C1157 |
| Description: | Center-staple paddle roller motor malfunction (middle) <When FS-526+SD-508 is installed> • The center staple paddle/C (M30) lock signal remains set to L for a set period of time while the center staple paddle/C (M30) is turning. |
| Causes: | Center staple paddle/C (M30) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M30 for proper drive coupling, and correct as necessary. - - 3 M30 operation check SDDB CN406<B>-11 to 15 SD-508 K-10 4 Change M30 - - 5 SDDB ICP5 conduction check - - 6 Change SDDB - - 7 Change FSCB |
| Error code: | C1158 |
| Description: | Center-staple paddle roller motor malfunction (leading edge) <When FS-527+SD-509 is installed>• Even after the set period of time has elapsed after the lower paddle motor (M22) starts running, a change of motor lock signal is not detected and neither the paper detection sensor/1 (PS43) nor the paper detection sensor/2 (PS44) is turned ON. |
| Causes: | lower paddle motor (M22) Paper detection sensor/1 (PS43) Paper detection sensor/2 (PS44) SD drive board (SDDB) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M22 for proper drive coupling, and correct as necessary. - - 3 PS43 I/O check, sensor check SDDB PJ9-8 (ON) SD-509 G-1 4 PS44 I/O check, sensor check SDDB PJ13-2 (ON) SD-509 G-3 5 M22 operation check SDDB PJ5-1 to 5 SD-509 B-4 6 Change M22 - - 7 Change SDDB - - 8 Change FSCB |
| Error code: | C1182 |
| Description: | Unsupported option trouble |
| Causes: | When JS-504 is installed: Shift motor (M2) Shift home sensor (PS6) JS control board (JSCB). When FS-527 is installed: Tray2 shift motor (M16) Tray2 shift home sensor (PS25) FS control board (FSCB) |
| Error code: | C1183 |
| Description: | Finishing option elevator drive malfunction |
| Causes: | Elevate motor (M15) Tray1 lower position sensor (PS21) Tray1 upper position sensor (PS24) Tray1 upper position switch (SW2) Tray1 lower position switch (SW3) FS control board (FSCB) |
| Error code: | C1190 |
| Description: | Finishing option aligning bar moving mechanism malfunction 1 |
| Causes: | Alignment plate motor (M13) Alignment plate home sensor (PS17) FS control board (FSCB) |
| Error code: | C1194 |
| Description: | Leading edge stopper motor drive malfunction <When FS-527 is installed> • The leading edge stopper home sensor (PS20) is turned neither ON nor OFF even after the set period of time has elapsed after the leading edge stopper motor (M14) is turned ON. |
| Causes: | Leading edge stopper motor (M14) Leading edge stopper home sensor (PS20) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M13 for proper drive coupling, and correct as necessary. - - 3 PS17 I/O check, sensor check FSCB PJ17-6 (ON) FS-527 B to C-8 4 M13 operation check FSCB PJ8-9 to 12 FS-527 B to C-6 5 Change M13 - - 6 Change FSCB |
| Error code: | C11A1 |
| Description: | Finishing option exit roller pressure/retraction failure |
| Causes: | Exit roller retraction motor (M9) Exit roller pressure sensor (PS12) FS control board (FSCB) |
| Error code: | C11A2 |
| Description: | Saddle exit roller pressure/retraction failure |
| Causes: | <When FS-536 or FS-536SD is installed> • Receiving roller retraction motor (M4) • Receiving roller retraction sensor (PS11) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Receiving roller retraction motor (M10) • Receiving roller retraction sensor (PS22) • FS control board (FSCB) |
| Error code: | C11A7 |
| Description: | Tray 3 exit roller pressure/ retraction malfunction <When JS-603 is installed> • The exit roller pressure sensor (PS12) is turned neither ON nor OFF even after the set period of time has elapsed after the exit roller retraction motor (M9) is turned ON. |
| Causes: | Tray3 exit roller retraction motor (M17) Tray3 exit roller retraction sensor (PS35) FS control board (FSCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M17 for proper drive coupling, and correct as necessary. - - 3 PS35 I/O check, sensor check FSCB PJ12-6 (ON) FS-527 (JS-603) L-10 4 M17 operation check FSCB PJ30-2 (REM) FS-527 (JS-603) L-9 5 Change M17 - - 6 Change FSCB |
| Error code: | C11B0 |
| Description: | Finishing option stapler unit CD drive failure |
| Causes: | Stapler movement motor (M11) Stapler home sensor/1 (PS18) Stapler home sensor/2 (PS19) FS control board (FSCB) |
| Error code: | C11B2 |
| Description: | Finishing option stapling mechanism malfunction 1 |
| Causes: | Stapler unit FS control board (FSCB) |
| Error code: | C11B5 |
| Description: | Side staple 1 drive failure |
| Causes: | Saddle stapler unit SD drive board (SDDB) FS control board (FSCB) |
| Error code: | C11C0 |
| Description: | Punch motor malfunction |
| Causes: | Punch motor/1 (M100) Punch home sensor/1 (PS100) FS control board (FSCB) |
| Error code: | C11E0 |
| Description: | Unsupported option trouble |
| Causes: | When FS-527 is installed: Duplex path switching motor (M2) Duplex path switching sensor (PS3)FS control board (FSCB). When JS-504 is installed: Route change motor (M3) Route change home sensor (PS4) JS control board (JSCB) |
| Error code: | C11E1 |
| Description: | Paper exit switching drive malfunction. <When FS-536 or FS-536SD is installed> The exchange folded paper output sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the FNS entry transport motor (M2) is turned ON. <When FS-537 or FS-537SD is installed> The route change gate home sensor (PS21) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the route change gate motor (M4) is turned ON. |
| Causes: | <When FS-536 or FS-536SD is installed> • FNS entry transport motor (M2) • Exchange folded paper output sensor (PS30) • FS control board (FSCB) <When FS-537 or FS-537SD is installed> • Route change gate motor (M4) • Route change gate home sensor (PS21) • FS control board (FSCB) |
| Remedy: | (a) When FS-536 or FS-536SD is installed 1. Check the connector between M2-FSCB J9 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS30-FSCB J4 for proper connection and correct as necessary. 4. PS30 I/O check, sensor check • Control signal: FSCB J4<A>-15 (ON) • Location of electrical component: FS-536/FS-536SD 14-C 5. M2 operation check • Control signal: FSCB J9<A>-1 to 4 • Location of electrical component: FS-536/FS-536SD 12-C 6. Replace M2. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.7 FS-536/FS-536SD) (b) When FS-537 or FS-537SD is installed 1. Check the connector between M4-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-FSCB J12 for proper connection and correct as necessary. 4. PS21 I/O check, sensor check • Control signal: FSCB J12<B>-12 (ON) • Location of electrical component: FS-537/FS-537SD 18-D 5. M4 operation check • Control signal: FSCB J21<B>-8 to 9 • Location of electrical component: FS-537/FS-537SD 18-D 6. Replace M4. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C11E2 |
| Description: | Paper exit switching (JS) drive malfunction. <When FS-537 or FS-537SD is installed> The sub tray/JS route change gate home sensor (PS23) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the sub tray discharge motor (M18) is turned ON. |
| Causes: | • Sub tray discharge motor (M18) • Sub tray/JS route change gate home sensor (PS23) • FS control board (FSCB) |
| Remedy: | 1. Check the connector between M18-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M18 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-FSCB J12 for proper connection and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J12<A>-16 (ON) • Location of electrical component: FS-537/FS-537SD 17-D 5. M18 operation check • Control signal: FSCB J12<A>-5 to 6 • Location of electrical component: FS-537/FS-537SD 16-D 6. Replace M18. 7. Replace FSCB. NOTICE • Link to the wiring diagram ( N.3.3 FS-537/FS-537SD) |
| Error code: | C2101 |
| Description: | Developer motor error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking the developer motor The developer motor drive is faulty. Execute U030 [DLP(K)] and check the developer motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 5 Checking the developer motor The developer motor is not properly attached or faulty. Reattach the developer motor. If not repaired, replace the motor. Detaching and reattaching the developer motor 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2151 |
| Description: | Secondary transfer roller pressure welding alienation • During a retraction operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its retracted position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. • During a pressure operation of the 2nd image transfer roller, the 2nd image transfer welding alienation sensor cannot detect the 2nd image transfer roller at its pressed position within a predetermined period of time after the 2nd image transfer retraction motor starts rotating. |
| Causes: | • 2nd transfer pressure motor (M3) • 2nd transfer pressure sensor (PS50) • Paper feed/transport drive board (PFTDB) • MFP board (MFPB) |
| Remedy: | 1 Check the M11 connector for proper connection and correct as necessary. 2 Check the connector of M11 for proper drive coupling and correct as necessary. 3 PS36 I/O check PRCB CN3PRCB-9 (ON) D-5. 4 Change the right door assy. 5 Change PRCB. |
| Error code: | C2152 |
| Description: | Transfer belt pressure welding alienation • During a retraction operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its retracted position within a predetermined period of time after the transfer belt retraction clutch is turned ON. • During a pressure operation of the transfer belt, the transfer belt retraction sensor cannot detect the transfer belt at its pressed position within a predetermined period of time after the transfer belt clutch is turned ON. |
| Causes: | • 1st transfer pressure sensor/K (PS51) • 1st transfer pressure sensor/YMC (PS52) • 1st transfer pressure motor (M21) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 PS31 I/O check PRCB CN36PRCB-15 (ON) D-26 to 27. 3 CL7 operation check PRCB CN39PRCB-10 (ON) D-23. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change CL7. 6 Change M5. 7 Change PRCB. |
| Error code: | C2163 |
| Description: | PC charge malfunction. When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined period of time. |
| Causes: | • Drum unit • High voltage unit/1 (HV1) • MFP board (MFPB) |
| Remedy: | 1. Check the drum unit for proper connection and correct as necessary. 2. Check the connector between HV1 CN1-MFPB CN9E for proper connection and correct as necessary. 3. Replace the drum unit. 4. Replace HV1. 5. Replace MFPB |
| Error code: | C2204 |
| Description: | Drum motor Y steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB Y at every 1s. |
| Remedy: | 1 Checking drum motor Y The drum motor Y drive is faulty. Execute U030 [Process] and check the drum motor Y operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor Y - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2257 |
| Description: | Cleaning brush motor’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Cleaning brush motor (M38) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M38-PRCB CN39 for proper connection and correct as necessary. 2 Check the M38 connector for proper drive coupling and correct as necessary. 4 M38 operation check PRCB CN39-1 to 7 20-K. 5 Replace M38. 6 PRCB ICP8 conduction check. 7 Replace PRCB. |
| Error code: | C2258 |
| Description: | Cleaning brush motor’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Cleaning brush motor (M38) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M38-PRCB CN39 for proper connection and correct as necessary. 2 Check the M38 connector for proper drive coupling and correct as necessary. 4 M38 operation check PRCB CN39-1 to 7 20-K. 5 Replace M38. 6 PRCB ICP8 conduction check. 7 Replace PRCB. |
| Error code: | C2259 |
| Description: | Developing motor/K’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Developing motor/K (M19) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M19-PRCB CN22 for proper connection and correct as necessary. 2 Check the M19 connector for proper drive coupling and correct as necessary. 3 M19 operation check PRCB CN22-1 to 5 16-K. 4 Replace M19. 5 PRCB ICP6 conduction check. 6 Replace PRCB. |
| Error code: | C225A |
| Description: | Developing motor/K’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Developing motor/K (M19) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M19-PRCB CN22 for proper connection and correct as necessary. 2 Check the M19 connector for proper drive coupling and correct as necessary. 3 M19 operation check PRCB CN22-1 to 5 16-K. 4 Replace M19. 5 PRCB ICP6 conduction check. 6 Replace PRCB. |
| Error code: | C225B |
| Description: | PC motor/K’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • PC motor/K (M18) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M18-PRCB CN21 for proper connection and correct as necessary. 2 Check the M18 connector for proper drive coupling and correct as necessary. 3 M18 operation check PRCB CN21-13 (LOCK) PRCB CN21-10 (REM) 16-K. 4 Replace M18. 5 PRCB ICP6 or ICP18 conduction check. 6 Replace PRCB. |
| Error code: | C225C |
| Description: | PC motor/K’s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • PC motor/K (M18) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M18-PRCB CN21 for proper connection and correct as necessary. 2 Check the M18 connector for proper drive coupling and correct as necessary. 3 M18 operation check PRCB CN21-13 (LOCK) PRCB CN21-10 (REM) 16-K. 4 Replace M18. 5 PRCB ICP6 or ICP18 conduction check. 6 Replace PRCB. |
| Error code: | C2350 |
| Description: | Toner suction fan failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Toner suction fan (FM7) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM7-relay CN326-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM7 operation check • Control signal: MFPB CN24E-7 (DRIVE), MFPB CN24E-9 (LOCK) • Location of electrical component: 1-K 4. Replace FM7. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C2353 |
| Description: | IU cooling fan/out`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • IU cooling fan /out (FM15) • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM15-PHRYB CN5 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM15 operation check • Control signal: PHRYB CN5-1 (DRIVE), PHRYB CN5-3 (LOCK) • Location of electrical component: 3-B 4. Replace FM15. 5. PHRYB F2 conduction check. 6. Replace PHRYB. 7. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C2354 |
| Description: | Rear side cooling fan motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | Rear side cooling fan motor (FM16) Printer control board (PRCB) |
| Remedy: | 1 Check the FM16 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM16 operation check PRCB CN18-2 (REM) PRCB CN18-3 (LOCK) C-12 to 13 4 Change FM16 - - 5 PRCB ICP7 conduction check - - 6 Change PRCB |
| Error code: | C2557 |
| Description: | Abnormally low toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 4 % or less for a given number of times consecutively. |
| Causes: | • Developing unit • Toner cartridge • Toner empty sensor/K (PZS/K) • Toner supply motor/K (M12) • Toner cartridge motor/CK (M14) • MFP board (MFPB) |
| Remedy: | 1 M3 operation check (At this time, IU must be non-installation.) PRCB CN39PRCB-1 to 4 D-23. 2 Reinstall imaging unit. 3 Reinstall toner cartridge. 4 Change imaging unit /K. 5 Change PRCB. |
| Error code: | C2558 |
| Description: | Abnormally high toner density detected black TCR sensor • TC ratio in the developing machine, which is determined by toner replenishing amount control mechanism, is 11 % or more for a given number of times consecutively. • When the connector of the TCR sensor is disconnected. |
| Causes: | • Developing unit • Toner cartridge • Sub hopper unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit. 2 Reinstall toner cartridge. 3 Change imaging unit /K. 4 Change PRCB. |
| Error code: | C255C |
| Description: | Black TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Developing unit • MFP board (MFPB) |
| Remedy: | 1 Reinstall imaging unit /K. 2 Change imaging unit /K. 3 Change PRCB. |
| Error code: | C2564 |
| Description: | Black TCR sensor failure. • The TCR sensor input is 0. • This detection is used for detecting disconnection of TCR sensor connector. |
| Causes: | • Developing unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Reinstall developing unit. 2. Check the connector between the developing unit-relay CN214-PHRYB CN6 for proper connection and correct as necessary. 3. Replace the developing unit. 4. PHRYB PS1 conduction check. 5. Replace PHRYB. 6. Replace MFPB |
| Error code: | C2650 |
| Description: | PF feed motor error (Side Multi Feeder) Object: Side multi feeder |
| Causes: | The ready signal is not at the L level (stable rotation) for passing 2s since the PF feed motor drive is started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected. The drive parts are faulty. Execute U247 [SMT] > [Motor On] to check the paper feeding operation. If the PF feed motor does not properly operate, reconnect the connector. Check if the PF feed roller and the drive gears rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. Executing U247 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF main PWB • PF main PWB - Engine PWB (Cable from the side multi feeder) Wiring diagram 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF drive unit (Side multi feeder) 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side multi feeder firmware to the latest version. Firmware Update 5 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2654 |
| Description: | EEPROM access error (IU K) |
| Causes: | Imaging unit /C Imaging unit /M Imaging unit /Y Drum unit /K Printer control board (PRCB) |
| Remedy: | 1 Clean the connection between the imaging unit and the machine if dirty 2 Reinstall imaging unit. 3 Check the harness for proper connection and correct as necessary. 4 Change imaging unit. 5 Change PRCB. |
| Error code: | C2A14 |
| Description: | Drum unit new release failure. The status with the new unit is not cleared after the new drum unit is set. |
| Causes: | • Drum unit • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the drum unit and the developing unit if dirty. 2. Reinstall the drum unit. 3. Check the harness for proper connection and correct as necessary. 4. Replace the drum unit. 5. Replace MFPB. |
| Error code: | C2A24 |
| Description: | Toner cartridge new release failure. The status with the new unit is not cleared after the new toner cartridge is set. |
| Causes: | • Toner cartridge • MFP board (MFPB) |
| Remedy: | 1. Clean the connection between the toner cartridge and the machine if dirty. 2. Reinstall the toner cartridge. 3. Check the harness for proper connection and correct as necessary. 4. Replace the toner cartridge. 5. Replace MFPB. |
| Error code: | C3101 |
| Description: | Fusing roller separation failure • With the fusing roller being retracted, the pulse of the fusing roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • With the fusing roller being pressed, the pulse of the roller retraction sensor does not change even after the specified period of time has passed after the fusing retraction motor started rotating. • During a pressure operation of the fusing roller, the fusing roller is not at the pressed position even after the roller retraction sensor counts the specified number of pulses after the fusing retraction motor starts rotating. |
| Causes: | • Fusing pressure home sensor (PS55) • Fusing pressure motor (M29) • Printer control board (PRCB) • Fusing unit |
| Remedy: | 1 Check the M12 connector for proper connection and correct as necessary. 2 PS38 I/O check PRCB CN28PRCB-8 (ON) D-25. 3 M12 operation check PRCB CN28PRCB-4 to 5 D-25. 4 Change M12. 5 Change fusing unit. 6 Change PRCB. |
| Error code: | C3102 |
| Description: | Heating roller failure to turn. During any state other than printing operation, the hard latch signal from one or both of the heating roller rotation latch detection 1 and the heating roller rotation latch detection 2 is turned ON. |
| Causes: | • Fusing unit • Fusing belt rotation sensor (PS56) (bizhub 958, bizhub PRO 958) • Heating roller rotation sensor (PS56) (bizhub 808/758) • Fusing motor (M30) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for proper connection and correct as necessary. 2. Check the connector between M30-MFPB CN16E for proper connection and correct as necessary. 3. Check the connector of M30 for proper drive coupling and correct as necessary. 4. Check the fusing unit-relay CN260-MFPB CN30E for proper connection and correct or change as necessary. 5. PS56 I/O check, sensor check • Control signal: MFPB CN30E-14 (ON) • Location of electrical component: 9-C, 12-C 6. M30 operation check • Control signal: MFPB CN16E-4 (REM), MFPB CN16E-7 (LOCK) • Location of electrical component: 10-K 7. Replace M30. 8. Replace the fusing unit. 9. MFPB F2E or F14E conduction check 10. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3201 |
| Description: | Fusing motor failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3202 |
| Description: | Fusing motor turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Fusing motor (M30) • Printer control board (PRCB) |
| Remedy: | 1 Check the M5 connector for proper connection and correct as necessary. 2 Check the loading status of the fusing unit drive, and correct the error as necessary. 3 Check the fusing unit, PRCB for proper connection and correct or change as necessary. 4 M5 operation check PRCB CN34PRCB-2 (REM) PRCB CN34PRCB-5 (LOCK) D-21. 5 Change M5. 6 Change PRCB. |
| Error code: | C3303 |
| Description: | Paper cooling fan/out`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Paper cooling fan/out (FM13) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM13-relay CN323-MFPB CN27E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM13 operation check • Control signal: MFPB CN27E<B>-10 (DRIVE), MFPB CN27E<B>-12 (LOCK) • Location of electrical component: 16-C 4. Replace FM13. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3305 |
| Description: | Switchback paper cooling fan/1`s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • Switchback paper cooling fan/1 (FM4) • Paper feed/transport drive board (PFTDB) |
| Remedy: | 1. Check the connector between FM4-relay CN283-relay CN280-relay CN279-relay CN271B-PFTDB CN2 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM4 operation check • Control signal: PFTDB CN2-15 (LOCK) • Location of electrical component: 5-P 4. Replace FM4. 5. PFTDB F14 conduction check 6. Replace PFTDB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C3424 |
| Description: | Fusing heaters trouble (soaking side) • After warm-up operation starts, the soaking roller thermistor does not detect a temperature as high as a predetermined one though a predetermined period of time has elapsed. |
| Causes: | Fusing unit IH power supply (IHPU) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, MFPB and DCPU for proper connection and correct or change as necessary. - - 4 Change fusing unit - - 5 Change IHPU - - 6 Change PRCB - - 7 Change DCPU |
| Error code: | C3425 |
| Description: | Fusing warm-up trouble. bizhub 958, bizhub PRO 958: • After warm-up operation starts, the fusing belt temperature sensor/1 (TEMS1) does not detect a temperature increasing to a predetermined one though a predetermined period of time has elapsed. • From the start of warm-up operation, it does not terminate within a predetermined period of time. b izhub 808/758: • After warm-up operation starts, the heating roller temperature sensor/1 (TEMS1) does not detect a temperature increasing to a predetermined one though a predetermined period of time has elapsed. • From the start of warm-up operation, it does not terminate within a predetermined period of time. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • IH power supply unit (IHPU) • Noise filter (NF1) • MFP board (MFPB) |
| Remedy: | 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the upper right door. 3. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 4. Check the connector between TEMS1-relay CN512-MFPB CN29E for proper connection and correct as necessary. 5. Check the connector between NF1 CN2-IHPU CN1 for proper connection and correct as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Replace the fusing unit. 8. Replace IHPU. 9. MFPB IC80E conduction check 10. Replace MFPB. 11. Replace NF1. |
| Error code: | C3721 |
| Description: | Fusing abnormally high temperature detection (heating side) • The heating roller thermistor continues to detect a temperature higher than a predetermined one for a predetermined period of time. • Hard protection signal L is detected continuously over a predetermined period of time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, PRCB and DCPU for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change PRCB. 6 Change DCPU. |
| Error code: | C3722 |
| Description: | Fusing abnormally high temperature detection (Edge of the heating side) Detected temperature of the heating roller thermistor/1 (TH1) goes beyond a given temperature for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3724 |
| Description: | Fusing abnormally high temperature detection (soaking side) • The soaking roller thermistor/1 continues to detect a temperature higher than a predetermined one for a predetermined period of time. • The signal is turned ON to activate the hard ratchet on the soaking side. |
| Causes: | Fusing unit IH power supply (IHPU) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, MFPB and DCPU for proper connection and correct or change as necessary. - - 4 Change fusing unit - - 5 Change IHPU - - 6 Change PRCB - - 7 Change DCPU |
| Error code: | C3725 |
| Description: | Fusing abnormally high temperature detection (Main of the heating side) • Detected temperature of the heating roller temperature sensor (TEMS) goes beyond a given temperature for a given period of time consecutively. • The hard protector signal error is detected for a given period of time consecutively. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3822 |
| Description: | Fusing abnormally low temperature detection (Edge of the heating roller) The heating roller thermistor/3 continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace IHPU. 6 Replace PRCB. 7 Replace NF1. |
| Error code: | C3824 |
| Description: | Fusing abnormally low temperature detection (soaking side) • The soaking roller thermistor/1 continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | Fusing unit IH power supply (IHPU) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, PRCB and DCPU for proper connection and correct or change as necessary. - - 4 Change fusing unit - - 5 Change IHPU - - 6 Change PRCB - - 7 Change DCPU |
| Error code: | C3825 |
| Description: | Fusing abnormally low temperature detection (Main of the heating roller) The heating roller temperature sensor (TEMS) continues to detect a temperature lower than a predetermined one for a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 PRCB ICP15 conduction check. 6 Replace PRCB. |
| Error code: | C3921 |
| Description: | Fusing sensor wire breaks detection (Center of the heating roller) • At the warm-up stage, the heating roller temperature sensor/2 voltage does not decrease by predetermined steps (temperature rise) within a predetermined time. |
| Causes: | Fusing unit Heating roller temperature sensor/1 (TEMS1) Heating roller temperature sensor/2 (TEMS2) Heating roller temperature sensor/3 (TEMS3) IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, PRCB and REDB for proper connection and correct or change as necessary. - - 4 Change TEMS1, TEMS2 or TEMS3 - - 5 Change fusing unit - - 6 Change IHPU - - 7 PRCB ICP17 conduction check - - 8 Change PRCB - - 9 Change REDB |
| Error code: | C3922 |
| Description: | Fusing sensor wire breaks detection (Edge of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller thermistor/1 (TH1) voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller thermistor/3 (TH3) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C3924 |
| Description: | Fusing sensor wire breaks detection (soaking side) • At the warm-up stage, the soaking roller thermistor/1 voltage does not decrease by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | Fusing unit IH power supply (IHPU) DC power supply (DCPU) Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). - - 2 Check the open/close operation of the upper right door. - - 3 Check the fusing unit, IHPU, PRCB and DCPU for proper connection and correct or change as necessary. - - 4 Change fusing unit - - 5 Change IHPU - - 6 Change PRCB - - 7 Change DCPU |
| Error code: | C3925 |
| Description: | Fusing sensor wire breaks detection (Center of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller temperature sensor (TEMS) voltage does not increase by predetermined steps (temperature rise) within a predetermined period of time. |
| Causes: | • Fusing unit • Heating roller temperature sensor (TEMS2) • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace PRCB. |
| Error code: | C392A |
| Description: | Fusing belt temperature sensor/1 contamination (Middle of the heating roller) (bizhub 958) Heating roller temperature sensor contamination (Middle of the heating roller (bizhub 808/758)bizhub 958, bizhub PRO 958: During waiting after a predetermined period of time after the warm-up stage terminates, the temperature detected by the fusing belt thermistor/1 (TH1) exceeds that detected by the fusing belt temperature sensor/1 (TEMS1) above a predetermined temperature, and this state continues for a predetermined period of time. bizhub 808/758: During waiting after a predetermined period of time after the warm-up stage terminates, the temperature detected by the heating roller thermostat/1 (TH1) exceeds that detected by the heating roller temperature sensor/1 (TEMS1) above a predetermined temperature, and this state continues for a predetermined period of time. |
| Causes: | • Fusing unit • Fusing belt temperature sensor/1 (TEMS1) (bizhub 958, bizhub PRO 958) • Heating roller temperature sensor/1 (TEMS1) (bizhub 808/758) • Fusing belt thermistor/1 (TH1) (bizhub 958, bizhub PRO 958) • Heating roller thermostat/1 (TH1) (bizhub 808/758) • IH power supply unit (IHPU) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1. Wipe the TEMS1 clean of dirt if any. • Clear away a dirt or a foreign object on the sensor with a cotton swab. • When a dirt is left even if you cleaned the sensor by above procedure, clear away a dirt or a foreign object on the sensor using a cotton swab dampened with the alcohol. And, wipe off the sensor with a dry cotton swab afterwards. 2. Check the TEMS1 for installed position and proper connector connection. 3. Check the TH1 for installed position and proper connector connection. 4. Check the connection of the fusing unit. 5. Check the fusing unit-MFPB CN30E for proper connection and correct or change as necessary. 6. Check the connector between IHPU CN8-MFPB CN18E for proper connection and correct as necessary. 7. Check the connector between DCPU CN009-MFPB CN31E for proper connection and correct as necessary. 8. Replace the fusing unit. 9. Replace MFPB. |
| Error code: | C3B02 |
| Description: | IH malfunction (CPU) A failure in communication with the fusing CPU continues for a predetermined period of time. |
| Causes: | • Fusing unit • IH coil unit • IH power supply (IHPU) • IH magnetic erasing board (IHMEB) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, IH coil unit, IHPU, IHMEB, NF1 and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace the IH coil unit. 6 Replace IHPU. 7 Replace IHMEB. 8 PRCB ICP5 conduction check. 9 Replace PRCB. 10 Replace NF1. |
| Error code: | C3B03 |
| Description: | IH malfunction (monitor) • Though the IH heater is ON, this status cannot be detected mechanically. (IH heater operation failure) • Though the IH heater is OFF, mechanically, the ON status is detected. (Malfunction of IH heater operation) |
| Causes: | • Fusing unit • IH coil unit • IH magnetic erasing board (IHMEB) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the open/close operation of the upper right door. 3 Check the fusing unit, IH coil unit, IHPU, IHMEB, NF1 and PRCB for proper connection and correct or change as necessary. 4 Replace the fusing unit. 5 Replace the IH coil unit. 6 Replace IHPU. 7 Replace IHMEB. 8 PRCB ICP5 conduction check. 9 Replace PRCB. 10 Replace NF1. |
| Error code: | C3B05 |
| Description: | IH temperature sensor defect • While the IH heater was on, IH temperature sensor was disconnected for more than the predetermined period of time. • While the IH heater was on, short circuit on IH temperature sensor continued for more than the predetermined period of time. • While the IH heater was on, temperature change occurred within the predetermined period of time with over the predetermined range, and they continued for more than the predetermined period of time. • While the IH heater was on, temperature around the heat radiator stayed high for over the predetermined period of time. |
| Causes: | IH coil unit IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the connection of the fusing unit. - - 2 Check the fusing unit, degaussing coil unit, IHPU, PRCB and REDB for proper connection and correct or change as necessary. - - 3 Change degaussing coil unit - - 4 Change IHPU - - 5 Change PRCB - - 6 Change REDB |
| Error code: | C3B06 |
| Description: | IH surge error • While the IH heater was on, IH stopped due to input voltage which exceeded that of surge detection voltage, and the surge detection voltage continued for more than the predetermined period of time. |
| Causes: | IH coil unit IH power supply (IHPU) Relay drive board (REDB) Printer control board (PRCB) |
| Remedy: | 1 Check the connection of the fusing unit. - - 2 Check the fusing unit, degaussing coil unit, IHPU, PRCB and REDB for proper connection and correct or change as necessary. - - 3 Change degaussing coil unit - - 4 Change IHPU - - 5 Change PRCB - - 6 Change REDB |
| Error code: | C3B07 |
| Description: | IH input power error • While the IH heater was ON, input power stayed at the high voltage power detection value or over for more than the predetermined period of time. • While the IH heater was ON, input power was at the low power detection value or under for more than the predetermined period of time. • While the IH heater was ON, input power was at the high voltage detection value or over for more than the predetermined period of time. • While the IH heater was ON, input power was below the low voltage detection value or under for more than the predetermined period of time. • While the IH heater was ON, inverter power stayed at the upper limit value or over for more than the predetermined period of time. • While the IH heater was ON, output voltage halt was detected. |
| Causes: | • IH coil unit • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connection of the fusing unit. 2 Check the fusing unit, IH coil unit, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 3 Replace the IH coil unit. 4 Replace IHPU. 5 Replace PRCB. 6 Replace NF1. |
| Error code: | C3B08 |
| Description: | IH input voltage error • While the IH heater was ON, input power was at the high voltage detection value or over for more than the predetermined period of time. • While the IH heater was ON, input voltage was at the low power detection value or under for more than the predetermined period of time. |
| Causes: | • IH coil unit • IH power supply (IHPU) • Noise filter (NF1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connection of the fusing unit. 2 Check the fusing unit, IH coil unit, IHPU, NF1 and PRCB for proper connection and correct or change as necessary. 3 Replace the IH coil unit. 4 Replace IHPU. 5 Replace PRCB. 6 Replace NF1. |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4301 |
| Description: | PH cooling fan’s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • PH cooling fan (FM14) • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM14-relay CN202-PHRYB CN4 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM14 operation check • Control signal: PHRYB CN4-8 (DRIVE), PHRYB CN4-9 (LOCK) • Location of electrical component: 6-B, 7-B 4. Replace FM14. 5. PHRYB F2 conduction check. 6. Replace PHRYB. 7. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C4501 |
| Description: | Laser malfunction. • SOS signal is not detected even after the lapse of a given period of time after starting the laser output. • SOS signal is not detected for a given period of time during printing or IDC sensor adjustment. |
| Causes: | • PH unit • PH relay board (PHRYB) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between the PH unit-PHRYB CN8 for proper connection and correct as necessary. 2. Replace the PH unit. 3. PHRYB IC5 conduction check. 4. Replace PHRYB. 5. Replace MFPB. |
| Error code: | C5104 |
| Description: | Main high-voltage error Y |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5105 |
| Description: | Transfer belt motor`s turning at abnormal timing The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary |
| Causes: | • Transfer belt motor (M1) • Printer control board (PRCB) |
| Remedy: | 1 Check the connector between M1-PRCB CN21 for proper connection and correct as necessary. 2 Check the transfer belt for proper drive coupling and correct as necessary. 3 M1 operation check PRCB CN21-3 (REM) PRCB CN21-6 (LOCK) 17-K. 4 Replace M1. 5 PRCB ICP7 or ICP18 conduction check. 6 Replace PRCB. |
| Error code: | C5304 |
| Description: | Cleaning lamp Y error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp Y. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the sub front PWB and the connector of the drum unit Y, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp Y. Replace the drum unit Y. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C5306 |
| Description: | IH coil cooling fan’s failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. |
| Causes: | • IH coil cooling fan (FM11) • MFP board (MFPB) |
| Remedy: | 1. Check the connector between FM11-relay CN324-MFPB CN24E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM11 operation check • Control signal: MFPB CN24E-1 (DRIVE), MFPB CN24E-3 (LOCK) • Location of electrical component: 1-K 4. Replace FM11. 5. MFPB F6E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram ( N.1 bizhub 958/808/758, bizhub PRO 958) |
| Error code: | C5351 |
| Description: | Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • DC power supply cooling fan (FM9) • DC power supply unit (DCPU) • MFP board (MFPB) |
| Remedy: | 1 Check the FM5 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM5 operation check PRCB CN30PRCB-11 (ON) PRCB CN30PRCB-12 (LOCK) K-8. 4 Change FM5. 5 Change DCPU. 6 Change PRCB. |
| Error code: | C5354 |
| Description: | Exhaust fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | • Ozone ventilation fan (FM6) • MFP board (MFPB) |
| Remedy: | 1 Check the FM4 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM4 operation check PRCB CN3PRCB-14 (ON) PRCB CN3PRCB-16 (LOCK) D-6. 4 Change FM4. 5 Change PRCB. |
| Error code: | C5356 |
| Description: | Cooling fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | Cooling fan motor (FM3) Printer control board (PRCB) |
| Remedy: | 1 Check the FM3 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 FM3 operation check PRCB CN15-4 (REM) PRCB CN15-6 (LOCK) K-7 to 8 4 Change FM3 - - 5 PRCB ICP6 conduction check - - 6 Change MFPB |
| Error code: | C5370 |
| Description: | Rear side cooling fan’s failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan remains stationary. |
| Causes: | • MFP control board cooling fan (FM17) • MFP board (MFPB) |
| Remedy: | 1 Check the connector between FM3-MFPB PJ26 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM3 operation check MFPB PJ26 (LOCK) 7-P. 4 Replace FM3. 5 Replace MFPB. |
| Error code: | C5372 |
| Description: | MFP control board CPU temperature failure. Temperature failure of CPU on the MFP board was detected. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Reboot the machine. 2. Check for clogging in the ventilation path between the MFPB and the power supply cooling fan, and correct as necessary. 3. Replace MFPB. |
| Error code: | C6001 |
| Description: | DF related configuration error 1. Inconsistency in the configuration with the installed DF is detected on the main body. |
| Causes: | • DF control board (DFCB) • Dual scan image processing board (DSIPB) • MFP board (MFPB) |
| Remedy: | 1. Check the type of the installed DF and replace it if it is a wrong one. 2. Correct the harness connection between DFCB CN12-relay CN47-MFPB CN1E if faulty. 3. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 4. Replace DFCB. 5. Replace DSIPB. 6. Replace MFPB. |
| Error code: | C6002 |
| Description: | DF related configuration error 2. Inconsistency in the configuration with the installed DF is detected on the DF. |
| Causes: | • DF control board (DFCB) • Dual scan image processing board (DSIPB) |
| Remedy: | 1. Check the type of the installed DF and replace it if it is a wrong one. 2. Correct the harness connection between DFCB CN12-relay CN47-MFPB CN1E if faulty. 3. Correct the harness connection between DSIPB CN1-MFPB CN24 if faulty. 4. Check the connectors of the dual scan image processing board (DSIPB) for proper connection, and correct as necessary. (Direction of the point of contact and connection state of the flat cable in particular) |
| Error code: | C6102 |
| Description: | Drive system home sensor malfunction • The scanner home sensor (PS201) is unable to detect the scanner located at its home position. • The scanner home sensor (PS201) is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor (PS201) detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor (PS201). |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6103 |
| Description: | Slider over running The scanner home sensor (PS201) detects the scanner at its home position during a period of time that begins with the time when a prescan command and a scan preparation command are executed and ends when a home return command is executed. |
| Causes: | • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201-SCDB PJ4 for proper connection and correct as necessary. 5 Check the connector between PS201-SCDB PJ6 for proper connection and correct as necessary. 6 Check the connector between SCDB PJ2-PRCB CN43 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 25-P. 8 M201 operation check SCDB PJ4-1 to 4 26-P. 9 Replace SCDB. 10 Replace PRCB. |
| Error code: | C6301 |
| Description: | Optical cooling fan motor’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. |
| Causes: | Optical cooling fan motor (M202) Scanner relay board (REYB/SCAN) MFP board (MFPB) |
| Remedy: | 1 Check the FM201 connector for proper connection and correct as necessary. - - 2 Check the fan for possible overload and correct as necessary. - - 3 M202 operation check REYB/SCAN PJ4-3 (LOCK) P-18 4 Change REYB/SCAN - - 5 Change MFPB |
| Error code: | C6704 |
| Description: | Image input time out. Image data is not input from the scanner to the MFP board (MFPB). |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Select [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Memory Bus Check] -> [Scanner -> Memory], and conduct the memory bus function. 2. Correct the harness connection between scanner section and MFPB if faulty. 3. MFPB F3E conduction check 4. Replace MFPB. 5. Replace the CCD unit. |
| Error code: | C6751 |
| Description: | CCD gain adjustment failure. • The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment. |
| Causes: | • LED exposure unit • Scanner drive board (SCDB) • CCD board (CCDB) • MFP board (MFPB) |
| Remedy: | 1. Correct the harness connection between CCDB PJ3-MFPB CN9 if faulty. 2. Correct the harness connection between CCDB PJ5-SCDB CN5 if faulty. 3. Correct the harness connection between SCDB CN1-DCPU CN005 if faulty. 4. Check for possible extraneous light and correct as necessary. 5. Clean the lens, mirrors, CCD surface, and shading sheet if dirty. 6. Correct reflective mirror of the scanner if faulty, or change scanner mirror. 7. Replace SCDB 8. Replace the CCD unit. 9. MFPB F3E conduction check 10. Replace MFPB. |
| Error code: | C6752 |
| Description: | ASIC clock input error (front side). When starting the machine, verification on reading and writing the predetermined value for image processing ASIC on CCD board (CCDB) was conducted, and verification failure was detected. |
| Causes: | • MFP board (MFPB) • CCD board (CCDB) |
| Remedy: | 1. Correct the harness connection of CCDB if faulty. 2. Replace the CCD unit. 3. MFPB F3E conduction check 4. Replace MFPB. |
| Error code: | C6901 |
| Description: | DSC board mount failure 1 When MFP detects that DSC board/1 (front side) is not properly installed. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6902 |
| Description: | DSC board bus check NG1-1 When DSC bus check (front side) detects an error. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6903 |
| Description: | DSC board bus check NG1-2 When DSC bus check (front side) detects an error. |
| Causes: | • DSC board/1 (DSCB/1; SC-508) • MFP board (MFPB) |
| Remedy: | 1 Correct the harness connection of DSCB/1 if faulty. 2 Replace DSCB/1. 3 Replace MFPB |
| Error code: | C6F01 |
| Description: | Scanner sequence trouble 1. The original transport interval becomes shorter than the predetermined value due to an original transport control error in original reading in DF. |
| Causes: | • MFP board (MFPB) • DF control board (DFCB) |
| Remedy: | 1. Correct the harness connection between main body and DF if faulty. 2. Replace DFCB. 3. Replace MFPB. |
| Error code: | C8101 |
| Description: | Before reading pressure welding alienation mechanism trouble. • During a pressure motion being performed, the before read sensor (PS6) output does not change from H to L. • During a retraction motion being performed, the before read sensor (PS6) output does not change from L to H. |
| Causes: | • Reading roller pressure/retraction motor (M6) • Before read sensor (PS6) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M6-relay CN118-DFCB CN4 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-relay CN120-DFCB CN11 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: DFCB CN11-2 (ON) • Location of electrical component: DF 1-C 5. M6 operation check • Control signal: DFCB CN4-1 to 2 • Location of electrical component: DF 10-C 6. Replace M6. 7. DFCB ICP9 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8102 |
| Description: | Turn around pressure welding alienation trouble •During a pressure motion being performed, the reverse roller sensor (PS7) output does not change from H to L. •During a retraction motion being performed, the reverse roller sensor (PS7) output does not change from L to H. |
| Causes: | Switchback roller pressure/retraction motor (M5) Reverse roller sensor (PS7) DF control board (DFCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M5 for proper drive coupling, and correct as necessary. - - 3 PS7 I/O check, sensor check REYB PJ3-3 (ON) DF-618 K to L-10 4 DFCB F9 conduction check - - 5 M5 operation check DFCB PJ6-10 to 11 DF-618 I-7 6 Change M5 - - 7 DFCB PS2 conduction check - - 8 Change DFCB |
| Error code: | C8103 |
| Description: | Lift up mechanism trouble (Upward movement). The lift up upper sensor (PS2) is not turned ON (unblocked) after a lapse of a given time after the lift-up motor (M5) moves up (is turned forward). |
| Causes: | • Lift-up motor (M5) • Lift up upper sensor (PS2) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M5-DFCB CN9 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-DFCB CN6 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: DFCB CN6-3 (ON) • Location of electrical component: DF 7-I 5. M5 operation check • Control signal: DFCB CN9-1 to 5 • Location of electrical component: DF 5-C 6. Replace M5. 7. DFCB ICP5 conduction check. 8. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8104 |
| Description: | Glass movement trouble • The glass home sensor (PS203) output does not change from H to L after a lapse of a given time while the original glass moving motor (M202) is working. • The glass home sensor (PS203) output does not change from L to H after a lapse of a given time while the original glass moving motor (M202) is working. |
| Causes: | Original glass moving unit Original glass moving motor (M202) Original glass position control board (OGPCB) |
| Remedy: | 1 Check the motor and sensor connectors for proper connection, and correct as necessary. - - 2 Check the connector of M202 for proper drive coupling, and correct as necessary. - - 3 Change original glass moving unit - - 4 Change OGPCB |
| Error code: | C8106 |
| Description: | Lift up mechanism failure (Downward movement). The lift up lower sensor (PS3) is not turned ON (unblocked) after a lapse of a given time after the lift-up motor (M5) goes down (is turned backward). |
| Causes: | • Lift-up motor (M5) • Lift up lower sensor (PS3) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between M5-DFCB CN9 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS3-DFCB CN10 for proper connection and correct as necessary. 4. PS3 I/O check, sensor check • Control signal: DFCB CN10-3 (ON) • Location of electrical component: DF 10-C 5. M5 operation check • Control signal: DFCB CN9-1 to 5 • Location of electrical component: DF 5-C 6. Replace M5. 7. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8302 |
| Description: | Cooling fan motor`s failure. The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. |
| Causes: | • Cooling fan motor (FM) • DF control board (DFCB) |
| Remedy: | 1. Check the connector between FM-relay CN115-DFCB CN19 for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM operation check • Control signal: DFCB CN19-3 (LOCK) • Location of electrical component: DF 4-C 4. Replace FM. 5. DFCB ICP10 conduction check. 6. Replace DFCB. NOTICE • Link to the wiring diagram ( N.2 Dual scan document feeder) |
| Error code: | C8401 |
| Description: | Nonvolatile memory error. The EEPROM writing is disabled. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Check the DFCB connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Replace DFCB. |
| Error code: | C9401 |
| Description: | Exposure LED lighting failure The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | C9402 |
| Description: | Exposure LED lighting abnormally The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job. |
| Causes: | • LED exposure unit (LA201) • Flat cable • CCD board (CCDB) • Scanner drive board (SCDB) • MFP board (MFPB) |
| Remedy: | 1 Check the connection between SCDB-LU201, and correct if necessary. 2 Check the connector between SCDB PJ1-PRCB CN43 for proper connection and correct as necessary. 3 Check the connector between CCDB PJ3-MFPB PJ01 for proper connection and correct as necessary. 4 Replace the LED exposure unit. 5 Replace CCDB. 6 Replace SCDB. 7 Replace PRCB. 8 Replace MFPB. |
| Error code: | CA051 |
| Description: | Standard controller configuration failure • The controller of the printer control board (PRCB) is faulty. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA052 |
| Description: | Controller hardware error • A controller hardware error is detected in the network I/F. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CA053 |
| Description: | Controller start failure • A controller start failure is detected in the controller interface. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check to see if the following setting has been correctly made: [Service Mode] - [System Settings] - [Image Controller]. If changing the setting, turn OFF the power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CC001 |
| Description: | Vendor connection failure |
| Causes: | • Printer control board (PRCB) • Coin vendor (Japan) • Coin vendor kit (North America, Europe) |
| Error code: | CC151 |
| Description: | ROM contents error upon startup (MSC) • A fault is detected in a sequence of ROM contents check of the MSC (PRCB) during starting |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | CC152 |
| Description: | ROM contents error upon startup (scanner). A fault is detected in a sequence of ROM contents check of the MFPB during starting |
| Remedy: | 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the appropriate board. |
| Error code: | CC153 |
| Description: | ROM contents error upon startup (PRT) • A fault is detected in a sequence of ROM contents check of the mechanical control board (MFPB) during starting. |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. |
| Error code: | CC155 |
| Description: | Finisher ROM error |
| Causes: | FS control board (FSCB) |
| Error code: | CC156 |
| Description: | DF ROM error. Data of flash ROM of the DF is determined to be faulty when the main power switch is turned ON. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace DFCB. |
| Error code: | CC157 |
| Description: | Finisher ROM error (ZU). Data of flash ROM of the z-folding unit is determined to be faulty when the power is turned ON. |
| Causes: | ZU control board (ZUCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace ZUCB |
| Error code: | CC158 |
| Description: | Finisher ROM error (RU). When a communication error is detected between the main body and the horizontal transport unit. |
| Causes: | • RU control board (RUCB) • FS control board (FSCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace RUCB - - 4 Replace FSCB |
| Error code: | CC159 |
| Description: | ROM contents error upon startup (DSC1) • A fault is detected in a sequence of ROM contents check of the DSC board during starting. |
| Causes: | DSC board (SC-507) |
| Remedy: | 1 Check the DSC board connector for proper connection and correct as necessary. 2 Disconnect and then connect the power cord. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3 Rewrite the firmware. 4 Change DSC board |
| Error code: | CC15A |
| Description: | ROM contents error upon startup (DSC2) • A fault is detected in a sequence of ROM contents check of the DSC board during starting. |
| Causes: | DSC board (SC-507) |
| Remedy: | 1 Check the DSC board connector for proper connection and correct as necessary. 2 Disconnect and then connect the power cord. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3 Rewrite the firmware. 4 Change DSC board |
| Error code: | CC15B |
| Description: | Flash ROM error (saddle). <When FS-536SD or FS-537SD is installed> Data of flash ROM of the saddle is determined to be faulty when the main power switch is turned ON. |
| Causes: | SD control board (SDCB) |
| Remedy: | 1. Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2. Rewrite the firmware. 3. Replace SDCB. (FS-536SD/FS-537SD) |
| Error code: | CC163 |
| Description: | ROM contents error (PRT) • The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Rewrite the firmware. 2 Change PRCB 2.1. Turn OFF the power switch and replace the current PRCB with a new one. (When using a PRCB of another machine in service, be sure to use a PRCB installed in the same model.) 2.2. Update the PRCB firmware. 2.3. After completing the firmware update, turn OFF and ON the power switch and check to see that warm-up is started. 2.4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SV ERB. 3 Change SV ERB 3.1. Replace the current SV ERB with a new one. 3.2. Turn ON the power switch and check to see that warm-up is started. (One minute is spent to prepare the new SV ERB for use. During the period, the control panel backlight stays off.) 3.3. Make the specified readjustments. 4 If the above actions do not solve the problem, contact KMBT. |
| Error code: | CC164 |
| Description: | ROM contents error (MSC) • The wrong model of firmware is detected in the MFP board when the power switch is turned ON. |
| Causes: | • eMMC board (eMMC) • MFP board (MFPB) |
| Remedy: | 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the corresponding board. 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC165 |
| Description: | ROM contents error (DF). When the power is turned ON, DF control board or firmware error is detected. |
| Causes: | DF control board (DFCB) |
| Remedy: | 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Replace DFCB |
| Error code: | CC170 ... CC184 |
| Description: | Dynamic link error during starting • A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. |
| Causes: | MFP board (MFPB) NVRAM board (NRB) |
| Remedy: | 1 If the malfunction code gC-C172h has occurred, access [Service Mode] - [System 2] - [Image Controller Setting] and check to see if gController 2,h gController 3,h or gOthersh is set for [Image Controller Setting]. If any of these is set, according to the kind of controller, select gController 0h or gController 1.h . . 2 Change MFPB. . . 3 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC185 |
| Description: | Dynamic link error during starting (SPF) • A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. |
| Causes: | MFP board (MFPB) NVRAM board (NRB) |
| Remedy: | 1 If the malfunction code gC-C172h has occurred, access [Service Mode] - [System 2] - [Image Controller Setting] and check to see if gController 2,h gController 3,h or gOthersh is set for [Image Controller Setting]. If any of these is set, according to the kind of controller, select gController 0h or gController 1.h . . 2 Change MFPB. . . 3 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC186 |
| Description: | Dynamic link error during starting (OAP) • A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. |
| Causes: | MFP board (MFPB) NVRAM board (NRB) |
| Remedy: | 1 If the malfunction code gC-C172h has occurred, access [Service Mode] - [System 2] - [Image Controller Setting] and check to see if gController 2,h gController 3,h or gOthersh is set for [Image Controller Setting]. If any of these is set, according to the kind of controller, select gController 0h or gController 1.h . . 2 Change MFPB. . . 3 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT. |
| Error code: | CC190 |
| Description: | Outline font load error. An error occurred while loading the outline font. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Format the hard disk. 4. Replace the hard disk. (HDD (A) / HDD (B)) 5. Replace MFPB. |
| Error code: | CC191 |
| Description: | Setting parameter load error (LDR). Upon startup, the processing of the loadable device driver setting data file failed. • RAM disk file creation failed. • Reading from the flash ROM failed. • An error occurred in API of the authentication module. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Turn OFF the main power switch, wait for 10 sec., then turn the switch ON. 2. Reinstall the loadable device driver. 3. Rewrite the firmware. 4. Replace MFPB. |
| Error code: | CD002 |
| Description: | JOB RAM save error • The error in save of JOB data to the memory/ hard disk and its read error are detected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD004 |
| Description: | Hard disk access error • Unable to communicate between the hard disk and printer control board (PRCB). |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | Check the hard disk connector for proper connection and correct as necessary. 2 Reinstall the hard disk. 3 Change hard disk. 4 Change MFPB. |
| Error code: | CD00F |
| Description: | Hard disk data transfer error. Data transfer from the hard disk is faulty. |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | 1 Check the hard disk connector for proper connection and correct as necessary. - - 2 Reinstall the hard disk. - - 3 Replace the hard disk 4 Replace MFPB |
| Error code: | CD010 |
| Description: | Hard disk unformat. Unformatted hard disk is connected. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Carry out the [Service Mode] -> [State Confirmation] -> [Memory/Storage Adjustment] -> [Format]. 2. Replace the hard disk. (HDD (A) / HDD (B)) 3. Replace MFPB. |
| Error code: | CD011 |
| Description: | Hard disk out of specifications mounted. A hard disk that falls outside the specifications is connected. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD020 |
| Description: | Hard disk verify error. The data abnormality is detected by the HDD verify check. |
| Causes: | • MFP board (MFPB) • Hard disk |
| Remedy: | 1 Check the hard disk connector for proper connection and correct as necessary. - - 2 Reinstall the hard disk. - - 3 Replace the hard disk 4 Replace MFPB |
| Error code: | CD030 |
| Description: | Hard disk management information reading error. The machine fails to read administrative information data saved in the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the connector between hard disk (A)-MFPB CN8, CN10 for proper connection and correct as necessary. 2. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. 3. Logically format the hard disk. 4. Physically format the hard disk. 5. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD041 ... CD046 |
| Description: | HDD command execution error. The error occurred inside the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD047 ... CD04B |
| Description: | HDD SCSI library error. The error occurred inside the hard disk. |
| Causes: | • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Check the hard disk specifications. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) |
| Error code: | CD201 |
| Description: | Memory error |
| Causes: | • MFP board (MFPB) • Memory |
| Remedy: | Check to see if the memory on MFPB is installed correctly. 2 Change the memory on MFPB. 3 Change MFPB. |
| Error code: | CD202 |
| Description: | Memory capacity discrepancy. • File memory capacity on the printer control board (PRCB) is not enough. • File memory capacity necessary for duplex printing is not enough during duplex unit mounting. |
| Causes: | • MFP board (MFPB) • Memory |
| Remedy: | 1 Check to see if the memory on MFPB is installed correctly. - - 2 Replace the memory on MFPB. - - 3 Replace MFPB |
| Error code: | CD203 |
| Description: | Memory capacity discrepancy 2. File memory capacity on the printer control board (PRCB) is not enough. |
| Causes: | • MFP board (MFPB) • Memory |
| Remedy: | 1 Check to see if the memory on MFPB is installed correctly. - - 2 Replace the memory on MFPB. - - 3 Replace MFPB |
| Error code: | CD211 |
| Description: | PCI-SDRAM DMA operation failure. Hardware related to the transfer of memory image of the printer control board (PRCB) fails to respond. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Replace MFPB |
| Error code: | CD212 |
| Description: | Compression/extraction timeout detection. Hardware related to the BTC compression function of the printer control board (PRCB) fails to respond. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Replace MFPB |
| Error code: | CD231 |
| Description: | No Fax memory at FAX board mounting |
| Causes: | MFP board (MFPB) FAX board |
| Remedy: | 1 Check to see if the FAX board is installed correctly. - - 2 Change PRCB. |
| Error code: | CD241 |
| Description: | Encryption ASIC error • Initialization error of the encrypted ASIC is detected during the machine is starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the MFP board connector for proper connection and correct as necessary. 2 Change MFPB |
| Error code: | CD242 |
| Description: | Encryption ASIC mounting error • The faulty of the installation of encrypted ASIC is detected during the machine is starting. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the MFP board connector for proper connection and correct as necessary. 2 Change MFPB |
| Error code: | CD261 |
| Description: | USB hub board failure. • When a failure is detected in USB hub board included in the local interface kit. • Non-standard USB device is connected. |
| Causes: | • MFP board (MFPB) • USB hub board (USBHB: EK-610/EK-611) |
| Remedy: | 1. Check the operation with another USB device. 2. Check the USB hub board connector for proper connection and correct as necessary. 3. Replace the USB hub board. 4. Replace MFPB. |
| Error code: | CD271 |
| Description: | The memory cannot be recognized with the i-Option activated. While the i-Option is activated, the memory on an MFPB cannot be recognized. |
| Causes: | MFP board (MFPB) |
| Remedy: | 1. Check MFPB for proper connection and correct as necessary. 2. Replace MFPB. |
| Error code: | CD272 |
| Description: | i-Option activated and HDD not installed. While the i-Option is activated, the hard disk is not installed. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) |
| Remedy: | 1. Access [Service Mode] -> [System 2] -> [HDD] and check to see if “Installed” is selected. 2. Replace the hard disk (A). 3. Replace MFPB. |
| Error code: | CD300 ... CD399 |
| Description: | NVRAM data error • Abnormality is detected by the abnormal check of each NVRAM data. |
| Remedy: | . When the data stored due to the NVRAM trouble is lost, backup data can be used for restoration. . Trouble code [C-D390] will be displayed when multiple errors (over 5) of NVRAM data are detected, which can be restored with one restoration command. . Data backup will be automatically performed every hour. Backup can also be performed manually with the following setting. [Service Mode] - [Enhanced Security] - [NVRAM Data Back Up] 618 1. When a trouble caused by NVRAM data error occurs, the screen below appears. 2. Select [Yes] and touch [OK]. 3. The screen will be shifted to the data restoration screen to perform data restoration. NOTE • When the restoration is performed in a short time, data restoration screen may not be displayed. 4. Check the message which indicates that the data restoration was successfully conducted. Turn OFF the main power switch and turn it ON again more than 10 seconds after. NOTE • In case it failed to restore data, return to the trouble code screen |
| Error code: | CD401 ... CD407 |
| Description: | CD401: NACK command incorrect CD402: ACK command incorrect CD403: Checksum error CD404: Receiving packet incorrect CD405: Receiving packet analysis error CD406: ACK receiving timeout CD407: Retransmission timeout |
| Causes: | MFP board (PRCB) |
| Remedy: | 1 Check whether there is an strong electromagnetic noise source near the main body. 2 Check the connectors on MFPB for proper connection and correct as necessary. 3 Change MFPB. |
| Error code: | CE001 ... CE007 |
| Description: | Abnormal message queue Task error Event error Memory access error Header access error DIMM initialize error |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the connectors on MFPB for proper connection and correct as necessary. 2 Replace MFPB |
| Error code: | CE002 |
| Description: | Message and method parameter failure. MFP board (MFPB) is faulty. |
| Causes: | • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Hard disk (B) (HDD (B): HD-524) |
| Remedy: | 1. Turn OFF the main power switch and turn it ON again, and conduct the following setting. [Service Mode] -> [System 1] -> [Initialization] - > [Clear All Data]. 2. Format the hard disk. 3. Replace the hard disk. (HDD (A) / HDD (B)) 4. Replace MFPB. |
| Error code: | CEEE1 |
| Description: | MFP board malfunction |
| Causes: | MFP board (MFPB) |
| Remedy: | 1 Check the connectors on MFPB for proper connection and correct as necessary. - - 2 Replace MFPB |
| Error code: | CEEE2 |
| Description: | Scanner section malfunction. A scanner part is faulty. |
| Causes: | • LED exposure unit • CCD board (CCDB) • Scanner drive board (SCDB) |
| Remedy: | 1. Check the connectors on CCDB or MFPB for proper connection and correct as necessary. 2. Replace SCDB 3. Replace the CCD unit. |
| Error code: | CEEE3 |
| Description: | Printer control board (PRCB) |
| Causes: | Printer control board (PRCB) |
| Remedy: | 1 Check the PRCB connector for proper connection and correct as necessary. - - 2 Replace PRCB |
| Error code: | CFB00 ... CFFA0 |
| Description: | Abort code |
| Causes: | MFP board (MFPB) DIMM0/DIMM1 JPEG board (SA-502) |
| Remedy: | 1 Check the MFPB connector for proper connection and correct as necessary. . . 2 Conduct the following setting. [Service Mode] - [Memory/HDD Adj.] - [Memory Check] - [Detail Check]. When gNGh is displayed, replace the appropriate memory or PWB. WORK0: DIMM0 WORK1: DIMM1 FILE0,1: MFP board FILE2,3: Not used FILE4,5: Not used . . 3 Conduct the following setting. [Service Mode] - [Memory/HDD Adj.] - [JPEG Check]. When gNGh is displayed, replace the JPEG board (JPEGB; SA-502). . . 4 Change MFPB |
