Kyocera ECOSYS FS-9120DN
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
180000
Скорость печати
A4
36
Общие характеристики |
|
|---|---|
Копир |
|
Печать фотографий |
|
Сканер |
|
Число страниц в месяц |
180 000 |
Тип устройства |
Принтер |
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Область применения |
большой офис |
Макс. формат |
A3 |
Принтер |
|
Двусторонняя печать |
|
Прямая печать |
|
Макс, разрешение для ч/б печати |
|
| По X | 1 800 |
| По Y | 600 |
Скорость ч/б печати |
|
| A4 | 36 |
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
40 000 |
Печать на: |
|
| Фотобумаге |
|
| Пленках |
|
| Этикетках |
|
Языки управления |
|
| PostScript |
|
Лотки |
|
Подача бумаги |
|
| Стандартная | 1 200 |
Вывод бумаги |
|
| Стандартный | 500 |
Интерфейсы |
|
Инфракрасный порт |
|
USB |
|
Ethernet (RJ-45) |
|
LPT |
|
Память/Процессор |
|
Объем памяти |
32 |
Макс, объем памяти |
544 |
Дополнительная информация |
|
Поддержка ОС |
|
| DOS |
|
| Linux |
|
| Mac OS |
|
| Windows |
|
Уровень шума |
|
| При работе | 56 |
Габариты |
|
Высота |
615 |
Ширина |
585 |
Глубина |
639 |
Вес |
67 |
Модули
PAPER CASSETTE
Bypass unit
Paper exit
FUSER UNIT
Bypass feed unit
Paper feed unit, 3
Paper feed unit, 1
Drive unit, 1
LSU
Paper feed unit, 2
Paper feed unit, 4
Drive unit, 2
Developer unit
Paper conveyers
Upper Frame Unit
Cleaning system
Enclosure
ELECTRICAL COMPONENTS
Детали Paper feed unit, 1
| Деталь: | CASSETTE |
| Парткод: | 2AR07011 |
| Деталь: | PLUG, QR/P15-8S-C (HIROSE) |
| Парткод: | J0463080 |
| Деталь: | LABEL, CASSETTE OPERATION |
| Парткод: | 2AR05150 |
| Деталь: | LABEL, PAPER UPPER LIMIT |
| Парткод: | 2AR05200 |
| Деталь: | BASE, CASSETTE |
| Парткод: | 2AR07020 |
| Деталь: | WORK PLATE, CASSETTE BASE |
| Парткод: | 2AR07030 |
| Деталь: | SHAFT, WORK PLATE |
| Парткод: | 2AR07040 |
| Деталь: | RAIL A, CURSOR |
| Парткод: | 2AR07052 |
| Деталь: | CURSOR A, CASSETTE |
| Парткод: | 2AR07060 |
| Деталь: | CURSOR B, CASSETTE |
| Парткод: | 2AR07071 |
| Деталь: | CURSOR C, CASSETTE |
| Парткод: | 2AR07080 |
| Деталь: | RAIL C, CURSOR |
| Парткод: | 2AR07091 |
| Деталь: | FRONT GUIDE C, CURSOR |
| Парткод: | 2AR07100 |
| Деталь: | REAR GUIDE C, CURSOR |
| Парткод: | 2AR07110 |
| Деталь: | LID A, CURSOR |
| Парткод: | 2AR07120 |
| Деталь: | COVER CASSETTE |
| Парткод: | 2BL04140 |
| Деталь: | GROUND PLATE, CASSETTE |
| Парткод: | 2AR07150 |
| Деталь: | MOUNT, CASSETTE STOPPER |
| Парткод: | 2AR07160 |
| Деталь: | RETAINER M4 |
| Парткод: | 2AR07180 |
| Деталь: | SHAFT, CASSETTE PULLEY |
| Парткод: | 2AR07190 |
| Деталь: | LEVER A, CURSOR |
| Парткод: | 2FG07010 |
| Деталь: | STOPPER, TRAILING EDGE DETECTION |
| Парткод: | 2AR07610 |
| Деталь: | PROTECTING PLATE, CASSETTE WIRE |
| Парткод: | 2AR07620 |
| Деталь: | LID, TRAILING EDGE DETECTION PLATE |
| Парткод: | 2AR07630 |
| Деталь: | WIRE, CASSETTE UNIT |
| Парткод: | 2AR27220 |
| Деталь: | RACK CURSOR |
| Парткод: | 3CY06090 |
| Деталь: | DETECTION PLATE, PAPER SIZE |
| Парткод: | 33907170 |
| Деталь: | CUSHION, CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | PULLEY, CASSETTE |
| Парткод: | 34907150 |
| Деталь: | CUSHION, CASSETTE R |
| Парткод: | 60907170 |
| Деталь: | GEAR 20,CURSOR |
| Парткод: | 3CY06100 |
| Деталь: | SPRING, CURSOR C |
| Парткод: | 66007120 |
| Деталь: | SPRING, PAD |
| Парткод: | 66106080 |
| Деталь: | PAD, CASSETTE |
| Парткод: | 66107100 |
| Деталь: | CASSETTE STOPPER |
| Парткод: | 77906210 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 2BC07860 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 2BL04160 |
| Деталь: | LABEL CASSETTE SIZE |
| Парткод: | 2BL05260 |
| Деталь: | PLATE SIZE C |
| Парткод: | 2BL06470 |
| Деталь: | PLATE SIZE IN |
| Парткод: | 2BL06910 |
| Деталь: | MOUNT CUSHION |
| Парткод: | 2BL06980 |
| Деталь: | STOPPER PAPER SP |
| Парткод: | 2BJ68190 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | PLATE NUMBER 2 |
| Парткод: | 2BL04370 |
| Деталь: | PARTS,PC700(A4) |
| Парткод: | 2BL93113 |
| Деталь: | PARTS,PC700(LTR) |
| Парткод: | 2BL93123 |
| Деталь: | BYPASS UNIT(C),SP |
| Парткод: | 2BL93432 |
| Деталь: | BYPASS UNIT(I),SP |
| Парткод: | 2BL93442 |
| Деталь: | FRONT CURSOR BYPASS |
| Парткод: | 2BL06660 |
| Деталь: | REAR CURSOR BYPASS |
| Парткод: | 2BL06670 |
| Деталь: | STAY LIFTPLATE |
| Парткод: | 2BL06650 |
| Деталь: | RACK, CASSETTE |
| Парткод: | 33907100 |
| Деталь: | GEAR 18, IDLE DEVELOPING |
| Парткод: | 65914120 |
| Деталь: | MOUNT, BYPASS PCB |
| Парткод: | 3A206461 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | FRICTION PLATE, BYPASS LEADING FEED |
| Парткод: | 34806490 |
| Деталь: | SWITCH,BYPASS SIZE DETECTION |
| Парткод: | 2CJ06260 |
| Деталь: | WIRE BYPASS TRAY |
| Парткод: | 2BL27210 |
| Деталь: | TABLE BYPASS |
| Парткод: | 2BL06610 |
| Деталь: | COVER BYPASSTRAY |
| Парткод: | 2BL06600 |
| Деталь: | LABEL BYPASSSIZE (C) |
| Парткод: | 2BL05010 |
| Деталь: | LABEL BYPASSSIZE (I) |
| Парткод: | 2BL05060 |
| Деталь: | JOINT, BYPASS PICKUP |
| Парткод: | 3A206130 |
| Деталь: | GEAR 30, FD EJECT IDLE |
| Парткод: | 72321350 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | MOUNT, BYPASS PE SWITCH |
| Парткод: | 3A206210 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | SHAFT BYPASSCAM |
| Парткод: | 2BL06760 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | ARM, BYPASS PE |
| Парткод: | 3A206100 |
| Деталь: | CAM BYPASS |
| Парткод: | 2BL06680 |
| Деталь: | SHAFT BYPASS |
| Парткод: | 2BL06770 |
| Деталь: | GEAR, TONER ROLLER |
| Парткод: | 45729416 |
| Деталь: | FILM BYPASS |
| Парткод: | 2BL06880 |
| Деталь: | UPPER PULLEY, BYPASS |
| Парткод: | 61706770 |
| Цена: | 1 900 ₽ |
| Деталь: | BASE BYPASSUNIT (1) |
| Парткод: | 2BL06511 |
| Деталь: | MOUNT BYPASSDRIVE |
| Парткод: | 2BL06690 |
| Деталь: | SHAFT RETARD |
| Парткод: | 2BL06750 |
| Деталь: | TORQUE LIMITER, BYPASS |
| Парткод: | 33906430 |
| Деталь: | PULLEY, SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | Holder, retard |
| Парткод: | 3A206170 |
| Деталь: | GEAR, 16 BYPASS PULLEY |
| Парткод: | 66006810 |
| Деталь: | SPRING RETARD |
| Парткод: | 2BL06860 |
| Деталь: | PIN, CASSETTE WORK PLATE |
| Парткод: | 66007310 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL07860 |
| Деталь: | WIRE BYPASS UNIT |
| Парткод: | 2BL27150 |
| Деталь: | COVER BYPASSUNIT |
| Парткод: | 2BL06530 |
| Деталь: | CLUTCH, FEED B |
| Парткод: | 2FG27170 |
| Деталь: | JOINT RETARD |
| Парткод: | 2BL06850 |
| Деталь: | LABEL RETARD |
| Парткод: | 2BL05040 |
| Деталь: | CLUTCH FEED |
| Парткод: | 2FG27160 |
| Деталь: | SPRING JOINTRETARD |
| Парткод: | 2BL06870 |
| Деталь: | GEAR 16, PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | GEAR 55/15 |
| Парткод: | 2BL06720 |
| Деталь: | TERMINAL, PAPER SIZE PCB |
| Парткод: | 33907110 |
| Деталь: | MINIATURE CLAMP, UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | EDGING, EDS-2 |
| Парткод: | M2104210 |
| Деталь: | MINI CLAMP,UAMS-02WL-0(KITAGAWA) |
| Парткод: | M2105210 |
| Деталь: | LIFTPLATE BYPASS |
| Парткод: | 2BL06642 |
| Деталь: | STOPPER GEAR 8-25 |
| Парткод: | 2BL06990 |
| Деталь: | PLATE BYPASS HOLD |
| Парткод: | 2BL06890 |
| Деталь: | LABEL, CAUTION GEAR |
| Парткод: | 3A205010 |
| Деталь: | PIN COVER |
| Парткод: | 2BL04410 |
| Деталь: | LABEL BYPASS JAM R |
| Парткод: | 2BL05100 |
| Деталь: | FRAME EXIT UP |
| Парткод: | 2BL21040 |
| Деталь: | PLATE EARTH EXIT F |
| Парткод: | 2BL21170 |
| Деталь: | ROLLER FEED SHIFT |
| Парткод: | 2BL21030 |
| Деталь: | ROLLER EXIT |
| Парткод: | 2BL21020 |
| Деталь: | ROLLER EXIT J |
| Парткод: | 2BL21050 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | GEAR EXIT Z20 |
| Парткод: | 2BL21430 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | PULLEY ONEWAY T30 |
| Парткод: | 2BL21211 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | COLLAR BELT DRIVE |
| Парткод: | 2FG22120 |
| Деталь: | GEAR EXIT Z19 |
| Парткод: | 2BL21220 |
| Деталь: | JOINT EXIT |
| Парткод: | 2BL21200 |
| Деталь: | GEAR EXIT JOINT Z26S |
| Парткод: | 2BL21390 |
| Деталь: | SWITCH FEED |
| Парткод: | 35327400 |
| Деталь: | ACTUATOR EXIT L |
| Парткод: | 2BL21130 |
| Деталь: | SPRING ACTUATOR L |
| Парткод: | 2BL21260 |
| Деталь: | SOLENOID, FEED SHIFT |
| Парткод: | 3AZ21890 |
| Деталь: | SPRING EXIT CHANGE |
| Парткод: | 2BL21440 |
| Деталь: | BKT SOLENOID |
| Парткод: | 2BL21190 |
| Деталь: | EDGING, EDS-0607M (KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | BKT DISCHARGER |
| Парткод: | 2BL21160 |
| Деталь: | STATIC ELIMINATOR, EJECT |
| Парткод: | 34821100 |
| Деталь: | PLATE EARTH EXIT R |
| Парткод: | 2BL21180 |
| Деталь: | FRAME EXIT |
| Парткод: | 2BL21010 |
| Деталь: | PLATE EARTH CHANGE |
| Парткод: | 2BL21470 |
| Деталь: | GUIDE EXIT CHANGE |
| Парткод: | 2BL21080 |
| Деталь: | CUT WASHER 6 |
| Парткод: | 2BL21510 |
| Деталь: | LEVER GUIDE CHANGE B |
| Парткод: | 2BL21370 |
| Деталь: | SPRING FEED SHIFT |
| Парткод: | 2BL21270 |
| Деталь: | LEVER GUIDE CHANGE |
| Парткод: | 2BL21100 |
| Деталь: | SPRING EXIT JOINT |
| Парткод: | 2BL21400 |
| Деталь: | ACTUATOR EXIT R |
| Парткод: | 2BL21120 |
| Деталь: | SPRING ACTUATOR R |
| Парткод: | 2BL21250 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | 2BL21070 |
| Деталь: | SHAFT EXIT PULLEY |
| Парткод: | 2BL21060 |
| Деталь: | PULLEY EXIT C |
| Парткод: | 2BL21520 |
| Деталь: | WIRE EJECT (P) |
| Парткод: | 2BL27160 |
| Деталь: | SPRING EXIT FULL |
| Парткод: | 2BL21480 |
| Деталь: | BKT EXIT FULL |
| Парткод: | 2BL21150 |
| Деталь: | MINIATURE CLAMP, UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | ACTUATOR EXIT FULL |
| Парткод: | 2BL21140 |
| Деталь: | PIN EXIT |
| Парткод: | 2BL21420 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | POLYESTER SLIDER WASHER 6.2X12X0.25T |
| Парткод: | C2891120 |
| Деталь: | EXIT ASSY |
| Парткод: | 2BL93102 |
| Деталь: | PARTS EXIT UNIT J |
| Парткод: | 2BL93492 |
| Деталь: | LOWER FRAME FIXING A |
| Парткод: | 2FG20022 |
| Деталь: | LOWER COVER FRAME |
| Парткод: | 2BL20310 |
| Деталь: | STATIC ELIMINATOR, HEAT ROLLER |
| Парткод: | 34820310 |
| Деталь: | PLATE SPRING FIXING |
| Парткод: | 2BL20230 |
| Деталь: | REAR FRAME FIXING |
| Парткод: | 2FG20040 |
| Деталь: | REAR PRESSING PLATE |
| Парткод: | 2FG20300 |
| Деталь: | FRONT FRAME FIXING |
| Парткод: | 2FG20030 |
| Деталь: | COVER FIXING WIRE |
| Парткод: | 2BL20290 |
| Деталь: | FRONT PRESSING PLATE |
| Парткод: | 2FG20290 |
| Деталь: | MOUNT THERMISTOR |
| Парткод: | 2BL20210 |
| Деталь: | THERMISTOR FIXING |
| Парткод: | 2FG20210 |
| Деталь: | ROLLER HEAT |
| Парткод: | 2FG20050 |
| Деталь: | BUSHING, HEAT ROLLER |
| Парткод: | 2FG20190 |
| Деталь: | BEARING, HEAT ROLLER |
| Парткод: | 2FG20230 |
| Деталь: | GEAR 55 HEAT ROLLER |
| Парткод: | 2FG20070 |
| Деталь: | STOPPER HEAT ROLLER |
| Парткод: | 2FG20200 |
| Деталь: | PARTS, PRESS ROLLER ASSY |
| Парткод: | 2FG93150 |
| Деталь: | SPRING PRESSURE |
| Парткод: | 2FG20240 |
| Деталь: | NUT FUSER |
| Парткод: | 2FG20360 |
| Деталь: | HEATER M120 FIXING |
| Парткод: | 2FG20120 |
| Деталь: | HEATER M230 FIXING |
| Парткод: | 2FG20140 |
| Деталь: | HEATER M110 FIXING |
| Парткод: | 2FG20320 |
| Деталь: | HEATER S120 FIXING |
| Парткод: | 2FG20130 |
| Деталь: | HEATER S230 FIXING |
| Парткод: | 2FG20150 |
| Деталь: | HEATER S110 FIXING |
| Парткод: | 2FG20330 |
| Деталь: | HEATER S120 FIXING |
| Парткод: | 2BL20140 |
| Деталь: | HEATER S230 FIXING |
| Парткод: | 2BL20160 |
| Деталь: | HEATER S110 FIXING |
| Парткод: | 2BL20120 |
| Деталь: | WIRE FIXING UNIT |
| Парткод: | 2BL27130 |
| Деталь: | THERMOSTAT FIXING |
| Парткод: | 2FG20220 |
| Деталь: | GEAR FIXING Z33 |
| Парткод: | 2BL20260 |
| Деталь: | UPPER FRAME FIXING A |
| Парткод: | 2FG20010 |
| Деталь: | UPPER COVER FRAME |
| Парткод: | 2BL20300 |
| Деталь: | CLAW HEAT ROLLER |
| Парткод: | 2BL20080 |
| Деталь: | SPRING CLAW |
| Парткод: | 2FG20350 |
| Деталь: | PCB FIXING ASSY |
| Парткод: | 2FH01080 |
| Деталь: | HOLDER PRESS SE |
| Парткод: | 2BL20320 |
| Деталь: | STATIC ELIMINATOR PRESS |
| Парткод: | 2BL20330 |
| Деталь: | GROUND PLATE FIXING |
| Парткод: | 2FG20280 |
| Деталь: | THERMISTOR FIXING UC |
| Парткод: | 2FG20340 |
| Деталь: | SPACER THERMOSTAT |
| Парткод: | 2FG20380 |
| Деталь: | SPACER THERMISTOR UC |
| Парткод: | 2FG20390 |
| Деталь: | PLATE FIXING ADJUST |
| Парткод: | 2FG02020 |
| Деталь: | SPACER FIXING ADJUST |
| Парткод: | 2FG02030 |
| Деталь: | CROSS RECESSED HEAD TAPPING P SCREW M3X08 |
| Парткод: | B1093080 |
| Деталь: | TRIPLE SCREW M3X8(BLACK)(SUPPLIED PARTS) |
| Парткод: | B4303080 |
| Деталь: | PARTS, FK-702 (E), SP |
| Парткод: | 2FH93031 |
| Деталь: | PARTS, FK-702 (U), SP |
| Парткод: | 2FH93021 |
| Деталь: | PARTS, FK-702 (TW), SP |
| Парткод: | 2FH93050 |
| Деталь: | MOUNT RAIL |
| Парткод: | 2BL06570 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BL06590 |
| Деталь: | RAIL BYPASS |
| Парткод: | 2BL06580 |
| Деталь: | BASE BYPASSFEED (1) |
| Парткод: | 2BL06500 |
| Деталь: | GROUNDPLATE BYPASS |
| Парткод: | 2BL06790 |
| Деталь: | ACTUATOR BYPASSFEED |
| Парткод: | 2BL06730 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL06800 |
| Деталь: | SPRING BYPASSFEED |
| Парткод: | 2BL06780 |
| Деталь: | SHAFT BYPASSFEED |
| Парткод: | 2BL06740 |
| Деталь: | RIGHT PULLEY, FEED |
| Парткод: | 33906660 |
| Деталь: | ROLLER4 BYPASSFEED |
| Парткод: | 2BL06560 |
| Деталь: | ROLLER2 BYPASSFEED |
| Парткод: | 2BL06540 |
| Деталь: | UPPERGUIDE BYPASS |
| Парткод: | 2BL06520 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | DIAL BYPASSFEED |
| Парткод: | 2BL06830 |
| Деталь: | PULLEY25 BYPASSFEED |
| Парткод: | 2BL06820 |
| Деталь: | BELT BYPASSFEED |
| Парткод: | 2BL06810 |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | FRONT LABEL BYPASS |
| Парткод: | 2BL05020 |
| Деталь: | UPPER LABEL BYPASS |
| Парткод: | 2BL05030 |
| Деталь: | BYPASS FEED UNIT |
| Парткод: | 2BL93390 |
| Деталь: | FRONT GUIDE REGIST |
| Парткод: | 2BL06260 |
| Деталь: | MOUNT REGIST SWITCH |
| Парткод: | 2BL06440 |
| Деталь: | SWITCH REGISTRATION |
| Парткод: | 2FG27110 |
| Деталь: | WIRE REGISTRATION |
| Парткод: | 2BL27170 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | PARTS,REGISTRATION |
| Парткод: | 2BL93450 |
| Цена: | 4 000 ₽ |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | PARTS, GUIDE TRANSFER ASSY |
| Парткод: | 2FG93110 |
| Деталь: | LABEL DRUM CAUTION A |
| Парткод: | 2FG05100 |
| Деталь: | LABEL DRUM CAUTION E1 |
| Парткод: | 2FG05080 |
| Деталь: | LABEL DRUM CAUTION E2 |
| Парткод: | 2FG05090 |
| Деталь: | FILM MIDDLE FEED RAIL R |
| Парткод: | 2FG06220 |
| Деталь: | PLUG, QR/P15-8S-C (HIROSE) |
| Парткод: | J0463080 |
| Деталь: | UPPER HOUSING, PAPER FEED |
| Парткод: | 2AR07200 |
| Деталь: | LOWER HOUSING, PAPER FEED |
| Парткод: | 2AR07210 |
| Деталь: | PULLEY, PAPER FEED |
| Парткод: | 2AR07220 |
| Цена: | 1 600 ₽ |
| Деталь: | PULLEY, SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | SHAFT, PAPER FEED |
| Парткод: | 2AR07250 |
| Деталь: | SHAFT, SEPARATION |
| Парткод: | 2AR07260 |
| Деталь: | SHAFT, LEADING FEED |
| Парткод: | 2AR07270 |
| Деталь: | SUPPORT PLATE FEED |
| Парткод: | 2BL07910 |
| Деталь: | PLATE LEADING FEED |
| Парткод: | 2BL07900 |
| Деталь: | WEIGHT, LEADING FEED PULLEY |
| Парткод: | 2AR07300 |
| Деталь: | LEVER, SEPARATION PULLEY RELEASE |
| Парткод: | 2AR07310 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 2BL07990 |
| Деталь: | ACTUATOR, PAPER EMPTY |
| Парткод: | 2AR07640 |
| Деталь: | HOLDER, ACTUATOR |
| Парткод: | 2AR07650 |
| Деталь: | GUIDE FILM, SEPARATION PULLEY |
| Парткод: | 2AR07660 |
| Деталь: | REINFORCEMENT, PRIMARY PAPER FEED |
| Парткод: | 2AR07670 |
| Деталь: | STOPPER, SUPPORT PLATE |
| Парткод: | 2AR07690 |
| Деталь: | GROUND PLATE, PRIMARY PAPER FEED |
| Парткод: | 2AR07790 |
| Деталь: | GEAR 15 |
| Парткод: | 34922420 |
| Деталь: | BUSHING, 6 REGISTRATION |
| Парткод: | 29806810 |
| Деталь: | TORQUE LIMITER, PAPER FEED |
| Парткод: | 33906070 |
| Деталь: | GEAR 16, PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | LOWER BUSHING, PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | SWITCH FEED |
| Парткод: | 35327400 |
| Деталь: | WIRE, PRIMARY PAPER FEED UNIT |
| Парткод: | 2AR27430 |
| Деталь: | PAPER FEED ASSY(CHN) |
| Парткод: | 2BJ00020 |
| Деталь: | PLATE DRIVE CONT. B |
| Парткод: | 2BL22450 |
| Деталь: | CLUTCH CONTAINER |
| Парткод: | 2BL22520 |
| Деталь: | SHAFT DRIVE CONT |
| Парткод: | 2BL22460 |
| Деталь: | COUPLING CONTAINER |
| Парткод: | 2BL22500 |
| Деталь: | SPRING DRIVE CONT. |
| Парткод: | 2BL22510 |
| Деталь: | BUSH DRIVE CONT 8 |
| Парткод: | 2BL22570 |
| Деталь: | GEAR Z24S-P40 |
| Парткод: | 2BL22480 |
| Деталь: | PULLEY CONT. DRIVE |
| Парткод: | 2BL22560 |
| Деталь: | BELT DRIVE CONTAINER |
| Парткод: | 2BL22590 |
| Деталь: | PLATE DRIVE CONT. A |
| Парткод: | 2BL22440 |
| Деталь: | GEAR Z40S-Z25S |
| Парткод: | 2BL22490 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | SOLENOID TONER |
| Парткод: | 2BL27510 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | GEAR Z41S-Z24S-P30 |
| Парткод: | 2BL22330 |
| Деталь: | CLUTCH FEED |
| Парткод: | 2FG27160 |
| Деталь: | BELT DRIVE FEED |
| Парткод: | 2BL22350 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GEAR M FEED Z25 |
| Парткод: | 2BL22740 |
| Деталь: | GEAR Z41S-P15 |
| Парткод: | 2BL22530 |
| Деталь: | LIFT MOTOR |
| Парткод: | 2BL27581 |
| Деталь: | BRACKET CLUTCH FEED |
| Парткод: | 2FG22090 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | GEAR Z60S-P20 |
| Парткод: | 2BL22540 |
| Деталь: | PRIMARY PAPER FEED BUSHING ASSY |
| Парткод: | 2AR00170 |
| Деталь: | GEAR Z41S-P18 |
| Парткод: | 2BL22420 |
| Деталь: | BELT DRIVE MPF |
| Парткод: | 2BL22400 |
| Деталь: | PLATE DRIVE MPF A |
| Парткод: | 2BL22370 |
| Деталь: | GEAR Z40S-Z32S |
| Парткод: | 2BL22550 |
| Цена: | 550 ₽ |
| Деталь: | PLATE DRIVE MPF B |
| Парткод: | 2BL22380 |
| Деталь: | PLATE DRIVE FEED A |
| Парткод: | 2FG22070 |
| Деталь: | FEED MOTOR |
| Парткод: | 2FG27020 |
| Деталь: | GEAR Z76H-Z35S |
| Парткод: | 2BL22320 |
| Деталь: | MINIATURE CLAMP, UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE SADDLE, YMC-10-0 (KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | WIRE SADDLE, WS-2NS |
| Парткод: | 49513902 |
| Деталь: | SPACER, KGPS-3S |
| Парткод: | 49628604 |
| Деталь: | WIRE CONT SW |
| Парткод: | 2BL27180 |
| Деталь: | PLATE TENSION A |
| Парткод: | 2BL22810 |
| Деталь: | PIN, DEV. UNIT HANDLE |
| Парткод: | 72114320 |
| Деталь: | PULLEY TENSION |
| Парткод: | 2BL22830 |
| Деталь: | SPRING PULLEY |
| Парткод: | 2BL22820 |
| Деталь: | PULLEY MPF DRIVE |
| Парткод: | 2BL22391 |
| Деталь: | PLATE DRIVE FEED B |
| Парткод: | 2FG22080 |
| Деталь: | PARTS, CONT DRIVE ASSY, SP |
| Парткод: | 2BL93380 |
| Деталь: | LSU UNIT |
| Парткод: | 5AAYA66E++01 |
| Деталь: | FRONT MOUNT HOUSING |
| Парткод: | 2BL13120 |
| Деталь: | PIN TENSION PULLEY |
| Парткод: | 76610320 |
| Деталь: | SPRING FIX LSU |
| Парткод: | 2BL13290 |
| Деталь: | FRONT ADJUSTING LSU |
| Парткод: | 2BL13070 |
| Деталь: | REAR ADJUSTING LSU |
| Парткод: | 2BL13060 |
| Деталь: | ADJUSTING PLT LSU |
| Парткод: | 2BL13250 |
| Деталь: | WIRE LSU |
| Парткод: | 2BL27060 |
| Деталь: | FILTER DUST SHIELD |
| Парткод: | 2BL23090 |
| Деталь: | MOUNT FAN |
| Парткод: | 2BL02230 |
| Деталь: | FAN COOLING (60-25) |
| Парткод: | 2BL27700 |
| Деталь: | WIRE SADDLE, YMC-10-0 (KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | FILTER DUST SHIELD B |
| Парткод: | 2BL23160 |
| Деталь: | SPONGE FAN |
| Парткод: | 2BL02240 |
| Деталь: | CORE ATFC-16-8-16 |
| Парткод: | 2FG27640 |
| Деталь: | WIRE DLP FAN |
| Парткод: | 2BL27330 |
| Деталь: | PARTS,VERTICAL FEED ASSY.SP |
| Парткод: | 2FG93080 |
| Деталь: | EARTH VERTICAL FEED |
| Парткод: | 2BL06220 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | ROLLER B FEED |
| Парткод: | 2BL06080 |
| Деталь: | ROLLER C FEED |
| Парткод: | 2BL06090 |
| Деталь: | CLUTCH FEED |
| Парткод: | 2FG27160 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GEAR Z42 FEED |
| Парткод: | 2BL06170 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | MOUNT FEED DRIVE A |
| Парткод: | 2FG06020 |
| Деталь: | GEAR Z21-36 FEED |
| Парткод: | 2FG06040 |
| Деталь: | GEAR 30,IDLE |
| Парткод: | 36222250 |
| Деталь: | GEAR 25 |
| Парткод: | 2AL06110 |
| Деталь: | GEAR Z25 JOINT |
| Парткод: | 2BL06380 |
| Цена: | 370 ₽ |
| Деталь: | MOUNT C FEED DRIVE |
| Парткод: | 2BL06130 |
| Деталь: | GEAR Z28-P18 FEED |
| Парткод: | 2BL06180 |
| Деталь: | BELT CONVEYING |
| Парткод: | 2BL06320 |
| Деталь: | WIRE CONVEYING |
| Парткод: | 2BL27190 |
| Деталь: | HOLDER FEED SWITCH |
| Парткод: | 2BL06450 |
| Деталь: | SWITCH CONVEYING |
| Парткод: | 2BL27410 |
| Деталь: | GUIDE VERTICAL FEED |
| Парткод: | 2BL06110 |
| Деталь: | GUIDE B FEED |
| Парткод: | 2BL06330 |
| Деталь: | LOCK COVER R |
| Парткод: | 2BL06490 |
| Деталь: | SPRING LEFT COVER |
| Парткод: | 2BL06460 |
| Деталь: | EARTH PUSH SWITCH |
| Парткод: | 2BL06940 |
| Деталь: | FRAME VERTICAL FEED A |
| Парткод: | 2FG06010 |
| Деталь: | MOUNT FEED DRIVE B |
| Парткод: | 2FG06030 |
| Деталь: | JOINT FEED DRIVE |
| Парткод: | 2FG06050 |
| Деталь: | SHAFT FEED JOINT |
| Парткод: | 2FG06060 |
| Деталь: | SPRING FEED JOINT |
| Парткод: | 2FG06070 |
| Деталь: | COLLAR FEED JOINT |
| Парткод: | 2FG06120 |
| Деталь: | SPRING GUIDE FEED |
| Парткод: | 2FG06130 |
| Деталь: | CASE, BU03P-TR-PC-H (JST) |
| Парткод: | J5016030 |
| Деталь: | WIRE SADDLE, YMC-10-0 (KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | FRONT RAIL FEED |
| Парткод: | 2BL06051 |
| Деталь: | REAR RAIL FEED |
| Парткод: | 2BL06061 |
| Деталь: | SHAFT LEFT COVER M |
| Парткод: | 2BL04520 |
| Деталь: | SPRING CONV OPEN |
| Парткод: | 2BL16230 |
| Деталь: | DUMPER LEFT COVER |
| Парткод: | 2BL06950 |
| Деталь: | STOPPER 7, CARTRIDGE |
| Парткод: | 33973300 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 2BL06430 |
| Деталь: | GUIDE ROLLER F |
| Парткод: | 2FG16160 |
| Деталь: | GUIDE ROLLER R |
| Парткод: | 2FG16170 |
| Деталь: | CAM DLP |
| Парткод: | 2BL14240 |
| Деталь: | SPRING CAM |
| Парткод: | 2BL14410 |
| Деталь: | MOUNT CAM |
| Парткод: | 2BL14140 |
| Деталь: | SHAFT CAM |
| Парткод: | 2BL14230 |
| Деталь: | BUSH POM |
| Парткод: | 2BM17920 |
| Деталь: | GEAR 18 |
| Парткод: | 2BL14250 |
| Деталь: | RIGHT ROLLER REGIST |
| Парткод: | 2FG06210 |
| Деталь: | POSITIONING PLATE,LSU |
| Парткод: | 2AR02250 |
| Деталь: | PARTS,MIDDLE FEED ASSY |
| Парткод: | 2FG93062 |
| Деталь: | GROUND PLATE A FEED |
| Парткод: | 2BL06230 |
| Деталь: | WIRE FEED 1 |
| Парткод: | 2BL27240 |
| Деталь: | GUIDE A FEED |
| Парткод: | 2BL06020 |
| Деталь: | SHAFT FEED A |
| Парткод: | 2BL06920 |
| Деталь: | FILM REGIST F |
| Парткод: | 2BL06480 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL06930 |
| Деталь: | FILM REGIST FF |
| Парткод: | 2BL06970 |
| Деталь: | GEAR Z42 BYPASS |
| Парткод: | 2BL06360 |
| Деталь: | MOUNT BYPASS FEED |
| Парткод: | 2FG06160 |
| Деталь: | GEAR Z25 FEED |
| Парткод: | 2BL06190 |
| Деталь: | GEAR Z35-15 FEED |
| Парткод: | 2BL06160 |
| Деталь: | GEAR Z28 FEED |
| Парткод: | 2BL06150 |
| Деталь: | MOUNT MID FEED DRIVE |
| Парткод: | 2FG06150 |
| Деталь: | GEAR 30 IDLE |
| Парткод: | 36222250 |
| Деталь: | HOUSING FEED A |
| Парткод: | 2FG06081 |
| Деталь: | CLUTCH REGISTRATION |
| Парткод: | 2FG27180 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GROUND PLATE GUIDE A |
| Парткод: | 2FG06170 |
| Деталь: | GUIDE MIDDLE FEED |
| Парткод: | 2FG06090 |
| Деталь: | SHAFT MIDDLE FEED |
| Парткод: | 2FG06100 |
| Деталь: | PULLEY MIDDLE FEED |
| Парткод: | 2FG06110 |
| Деталь: | FILM MIDDLE FEED |
| Парткод: | 2FG06200 |
| Деталь: | SHAFT CHANGE PULLEY |
| Парткод: | 2BL21361 |
| Деталь: | PULLEY FEED SHIFT |
| Парткод: | 2BL21330 |
| Деталь: | GUIDE EXIT L |
| Парткод: | 2BL21290 |
| Деталь: | SPRING CHANGE PULLEY |
| Парткод: | 2BL21340 |
| Деталь: | MOUNT REAR GUIDE |
| Парткод: | 2FG20181 |
| Деталь: | REAR GUIDE FIXING |
| Парткод: | 2FG20170 |
| Деталь: | FULCRUM PIN, FIXING |
| Парткод: | 34920170 |
| Деталь: | CLAW PRESS ROLLER |
| Парткод: | 2BL20350 |
| Деталь: | SHAFT, PRESSURE ROLLER SEPARATION CLAW |
| Парткод: | 2AR20510 |
| Деталь: | SPRING PRESS ROLLER |
| Парткод: | 2FG20370 |
| Деталь: | SPRING, DEVELOPING ROCK |
| Парткод: | 65009050 |
| Деталь: | GUIDE FEED SHIFT L |
| Парткод: | 2BL21410 |
| Деталь: | LEFT COVER MIDDLE |
| Парткод: | 2BL04511 |
| Деталь: | GROUND PLATE LEFT FAN |
| Парткод: | 2BL23110 |
| Деталь: | PLATE LEFT COVER M |
| Парткод: | 2BL04621 |
| Деталь: | GROUND PLATE LEFT B |
| Парткод: | 2BL04700 |
| Деталь: | SHAFT L COVER LOCK M |
| Парткод: | 2BL04540 |
| Деталь: | LEVER L COVER LOCK M |
| Парткод: | 2BL04550 |
| Деталь: | SPRING L COVER LOCK |
| Парткод: | 2BL04560 |
| Деталь: | LEVER COVER RELEASE |
| Парткод: | 2BL04600 |
| Деталь: | PIN, ORIGINAL HOLDER |
| Парткод: | 73912281 |
| Деталь: | STRAP COVER |
| Парткод: | 2BL04680 |
| Деталь: | GUIDE LEFT COVER M |
| Парткод: | 2BL21320 |
| Деталь: | FAN MOTOR 4 |
| Парткод: | 2FG27080 |
| Деталь: | WIRE CONVEYING FAN |
| Парткод: | 2BL27300 |
| Деталь: | FILM WIRE PROTECT |
| Парткод: | 2BL21460 |
| Деталь: | COVER EXIT L |
| Парткод: | 2BL04650 |
| Деталь: | FRONT PLATE EXIT L |
| Парткод: | 2BL04660 |
| Деталь: | GUIDE FILM DU |
| Парткод: | 2BL21490 |
| Деталь: | REAR PLATE EXIT L |
| Парткод: | 2BL04670 |
| Деталь: | FILM WIRE PROTECT B |
| Парткод: | 2BL21500 |
| Деталь: | LABEL DRUM CAUTION |
| Парткод: | 2BL05271 |
| Деталь: | SPONGE LEFT FAN |
| Парткод: | 2BL23170 |
| Деталь: | LEFT COVER FEED |
| Парткод: | 2BL06100 |
| Деталь: | SPRING FEED |
| Парткод: | 2BL06340 |
| Деталь: | SHAFT FEED PULLEY |
| Парткод: | 2BL06211 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL16080 |
| Деталь: | STRAP RELEASE |
| Парткод: | 2BL06960 |
| Деталь: | RETAINING PIN, VERTICAL CONVEYING |
| Парткод: | 2AR07540 |
| Деталь: | LABEL LEFT COVER A |
| Парткод: | 2BL05250 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | 2BL05110 |
| Деталь: | SHIELD 10X8X20,GASKET |
| Парткод: | 2AC26310 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | MOUNT OZONE FILTER A |
| Парткод: | 2FG23020 |
| Деталь: | FILTER OZONE A |
| Парткод: | 2FG23030 |
| Деталь: | PARTS, DRIVE UNIT DR-702 |
| Парткод: | 2FH93110 |
| Деталь: | MAIN MOTOR |
| Парткод: | 2FG27190 |
| Деталь: | GUIDE DLP |
| Парткод: | 2BL22140 |
| Деталь: | SPRING JOINT FUSER |
| Парткод: | 2BL22240 |
| Деталь: | GEAR Z36S-Z31H |
| Парткод: | 2BL22220 |
| Деталь: | GEAR Z50H |
| Парткод: | 2BL22190 |
| Деталь: | GEAR Z37H-Z28H |
| Парткод: | 2BL22180 |
| Деталь: | GEAR Z34H |
| Парткод: | 2BL22230 |
| Деталь: | GEAR Z59H-Z44S |
| Парткод: | 2FG22030 |
| Деталь: | GEAR Z76H-Z35H |
| Парткод: | 2BL22710 |
| Деталь: | GEAR Z37S |
| Парткод: | 2BL22770 |
| Деталь: | GEAR Z22S |
| Парткод: | 2FG22040 |
| Деталь: | GEAR DRUM Z76H-Z30H |
| Парткод: | 2BL22160 |
| Деталь: | GEAR JOINT Z32S |
| Парткод: | 2BL22210 |
| Деталь: | PLATE DRIVE FRONT |
| Парткод: | 2FG22010 |
| Деталь: | PLATE GUIDE DRUM |
| Парткод: | 2BL22170 |
| Деталь: | SHAFT DRIVE DRUM FW |
| Парткод: | 2BL22840 |
| Деталь: | GEAR DRUM Z70H |
| Парткод: | 2BL22050 |
| Деталь: | BEARING 6900ZZNR |
| Парткод: | G3169000 |
| Деталь: | PLATE DRIVE REAR |
| Парткод: | 2FG22020 |
| Деталь: | MOTOR EJECT |
| Парткод: | 2BL27560 |
| Деталь: | PLATE DRIVE EXIT A |
| Парткод: | 2FG22050 |
| Деталь: | GEAR Z47S-Z28S |
| Парткод: | 2BL22800 |
| Деталь: | GEAR EXIT Z30S |
| Парткод: | 2BL22630 |
| Деталь: | CLUTCH REGISTRATION |
| Парткод: | 2FG27180 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | DUCT DRUM |
| Парткод: | 2BL23020 |
| Деталь: | COVER DUCT DRUM |
| Парткод: | 2FG23010 |
| Деталь: | DUCT DLP |
| Парткод: | 2BL23030 |
| Деталь: | FAN MOTOR 1 |
| Парткод: | 2FG27130 |
| Деталь: | LID DLP DUCT |
| Парткод: | 2BL23040 |
| Деталь: | RETAINER FLYWHEEL |
| Парткод: | 2BL22850 |
| Деталь: | FLYWHEEL 190 |
| Парткод: | 2BL22860 |
| Деталь: | WEIGHT 190 |
| Парткод: | 2BL22870 |
| Деталь: | MOUNT BASE TERMINAL |
| Парткод: | 2BL26150 |
| Деталь: | PLATE TRANSFER A |
| Парткод: | 2BL26160 |
| Деталь: | PLATE SEPARATION A |
| Парткод: | 2BL26170 |
| Деталь: | EMPTY SW ASSY |
| Парткод: | 2BL01170 |
| Деталь: | DUCT MAIN A |
| Парткод: | 2BL23050 |
| Деталь: | DUCT MAIN B |
| Парткод: | 2BL23060 |
| Деталь: | FAN MOTOR 2 |
| Парткод: | 2FG27060 |
| Деталь: | WIRE SADDLE, WS-2NS |
| Парткод: | 49513902 |
| Деталь: | WIRE CONTAINER |
| Парткод: | 2BL27120 |
| Деталь: | RAIL DRUM R |
| Парткод: | 2BL02220 |
| Деталь: | WIRE SADDLE, YMC-10-0 (KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | MOUNT REAR FAN |
| Парткод: | 2BL23070 |
| Деталь: | FILM COOLING |
| Парткод: | 2BL23100 |
| Деталь: | FILM BKT CLUTCH |
| Парткод: | 2BL22880 |
| Деталь: | BRACKET CLUTCH |
| Парткод: | 2BL22150 |
| Деталь: | FILM DUCT DLP B |
| Парткод: | 2BL23140 |
| Деталь: | FILM DUCT DLP A |
| Парткод: | 2BL23130 |
| Деталь: | PLATE DRIVE EXIT B |
| Парткод: | 2FG22060 |
| Деталь: | BUSH,CUTTER |
| Парткод: | 49021301 |
| Деталь: | MOUNT FLYWHEEL |
| Парткод: | 2BL22890 |
| Деталь: | DV-700 |
| Парткод: | 2BL93010 |
| Деталь: | RAIL DLP |
| Парткод: | 2BL14200 |
| Деталь: | FRONT ARM RAIL |
| Парткод: | 2BL14180 |
| Деталь: | PIN,JAM REMOVEMENT DIAL |
| Парткод: | 36006140 |
| Деталь: | STUD SCREW S |
| Парткод: | 2BL14660 |
| Деталь: | PIN LEVER DLP |
| Парткод: | 2BL14220 |
| Деталь: | LEVER DLP |
| Парткод: | 2BL14210 |
| Деталь: | SEAL WIRE |
| Парткод: | 2BL14480 |
| Деталь: | REAR ARM RAIL |
| Парткод: | 2BL14190 |
| Деталь: | RECEPTACLE, 9715S-10A (IRS) |
| Парткод: | J7340100 |
| Деталь: | GROUND PLATE RAIL |
| Парткод: | 2BL14350 |
| Деталь: | PARTS, FEED UNIT FE-702 |
| Парткод: | 2FH93100 |
| Деталь: | BASE CONVEYING A 1 |
| Парткод: | 2FG16260 |
| Деталь: | PLATE PAPER GUIDE |
| Парткод: | 2FG16200 |
| Деталь: | PLATE TRANS B |
| Парткод: | 2BL16150 |
| Деталь: | PLATE SEPARATION B |
| Парткод: | 2BL16170 |
| Деталь: | SPRING FEED |
| Парткод: | 2FG16320 |
| Деталь: | SHAFT FEED |
| Парткод: | 2FG16280 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL16080 |
| Деталь: | SPRING REGIST F |
| Парткод: | 2FG16300 |
| Деталь: | SPRING REGIST R |
| Парткод: | 2FG16310 |
| Деталь: | ROLLER REGIST |
| Парткод: | 2FG16021 |
| Деталь: | BUSHING REGIST |
| Парткод: | 2BL16260 |
| Деталь: | STOPPER BUSH |
| Парткод: | 2BL16030 |
| Деталь: | GEAR REGIST Z18 |
| Парткод: | 2BL16060 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | GUIDE REGIST F |
| Парткод: | 2BL16130 |
| Цена: | 330 ₽ |
| Деталь: | GUIDE FEED F |
| Парткод: | 2BL16250 |
| Деталь: | SHAFT CONVEYING |
| Парткод: | 2BL16210 |
| Деталь: | SPRING CONVEYING B |
| Парткод: | 2BL16240 |
| Деталь: | HOOK CONVEYING |
| Парткод: | 2BL16190 |
| Деталь: | SPRING CONVEYING |
| Парткод: | 2BL16200 |
| Деталь: | HANDLE CONVEYING |
| Парткод: | 2BL16180 |
| Деталь: | STRAP CONVEYING A |
| Парткод: | 2BL16100 |
| Деталь: | STRAP CONVEYING B |
| Парткод: | 2BL16110 |
| Деталь: | UNDER CLEANER REGIST |
| Парткод: | 2BL07950 |
| Цена: | 1 500 ₽ |
| Деталь: | PULLEY REGIST |
| Парткод: | 2FG16030 |
| Деталь: | CUT WASHER 10 |
| Парткод: | 2BL07970 |
| Деталь: | PLATE TRANS UNIT GND |
| Парткод: | 2BL16160 |
| Деталь: | PARTS, TR-702,SP |
| Парткод: | 2FH93040 |
| Деталь: | COLLAR TRANS ROLLER |
| Парткод: | 2BL17030 |
| Деталь: | SPACER SEPARATION |
| Парткод: | 2FG17020 |
| Деталь: | HOUSING TRANSFER |
| Парткод: | 2BL17010 |
| Деталь: | BRUSH SEPARATION |
| Парткод: | 2FG17040 |
| Деталь: | HOLDER SEPARATION A |
| Парткод: | 2FG17010 |
| Деталь: | PLATE TRANS UNIT |
| Парткод: | 2BL17050 |
| Деталь: | BUSH TRANS ROLLER |
| Парткод: | 2BL17060 |
| Деталь: | SPRING TRANS R |
| Парткод: | 2FG17160 |
| Деталь: | SPRING TRANS F |
| Парткод: | 2BL17070 |
| Деталь: | BUSHING.CLEANING BLADE SHAFT |
| Парткод: | 75718040 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 2BL17021 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BL17170 |
| Деталь: | PULLEY TRANS ROLLER |
| Парткод: | 2BL17040 |
| Деталь: | GEAR TRANS Z25H |
| Парткод: | 2BL17090 |
| Деталь: | FILM FEED SHAFT R |
| Парткод: | 2FG16340 |
| Деталь: | ROLLER DU FEED UP |
| Парткод: | 2BL07020 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | ROLLER DU FEED LOW |
| Парткод: | 2BL07030 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | CLUTCH FEED |
| Парткод: | 2FG27160 |
| Деталь: | GEAR 25 |
| Парткод: | 2AL06110 |
| Деталь: | GEAR IDLE 20 |
| Парткод: | 66506630 |
| Деталь: | SPRING DU JOINT |
| Парткод: | 2BL07080 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | WIRE DUPLEX |
| Парткод: | 2BL27200 |
| Деталь: | ACTUATOR DU |
| Парткод: | 2BL07090 |
| Деталь: | SPRING DU ACT. |
| Парткод: | 2BL07130 |
| Деталь: | FILM WIRE DU |
| Парткод: | 2BL07140 |
| Деталь: | JOINT DU |
| Парткод: | 2BL07070 |
| Деталь: | FRAME DU |
| Парткод: | 2BL07010 |
| Деталь: | PLATE EARTH DU |
| Парткод: | 2BL07110 |
| Деталь: | SPRING DU PULLEY |
| Парткод: | 2BL07060 |
| Деталь: | SHAFT DU PULLEY |
| Парткод: | 2BL07051 |
| Деталь: | PULLEY DU |
| Парткод: | 2BL07040 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | PLATE NUT DU |
| Парткод: | 2BL07120 |
| Деталь: | PLATE MID FEED UNIT |
| Парткод: | 2FG16010 |
| Деталь: | SPACER REGIST |
| Парткод: | 2FG16250 |
| Деталь: | SHEET CONVEYING |
| Парткод: | 2FG16270 |
| Деталь: | GUIDE FEED |
| Парткод: | 2FG16290 |
| Деталь: | HOLDER SHAFT A |
| Парткод: | 2FG16330 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | FILM PLATE TRANS |
| Парткод: | 2FG16350 |
| Деталь: | FILM PLATE MID |
| Парткод: | 2FG16360 |
| Деталь: | GUIDE RIB DU |
| Парткод: | 2BL07150 |
| Деталь: | FRONT FRAME |
| Парткод: | 2BL02010 |
| Деталь: | FRONT FRAME |
| Парткод: | 2FG02040 |
| Деталь: | REAR FRAME |
| Парткод: | 2BL02020 |
| Деталь: | REAR FRAME |
| Парткод: | 2FG02050 |
| Деталь: | BASE |
| Парткод: | 2BL02030 |
| Деталь: | BASE MIDDLE |
| Парткод: | 2BL02040 |
| Деталь: | MOUNT OPERATION |
| Парткод: | 2BL04290 |
| Деталь: | LABEL RADIATION |
| Парткод: | 2BL05150 |
| Деталь: | LOWER LEFT REINFORCEMENT ASSY |
| Парткод: | 2AR00030 |
| Деталь: | LOWER LEFT REINFORCEMENT |
| Парткод: | 2AR02060 |
| Деталь: | LEFT RAIL, CASSETTE |
| Парткод: | 2AR07140 |
| Деталь: | PULLEY, CASSETTE RAIL |
| Парткод: | 2AR07800 |
| Деталь: | FRONT PIN, CASSETTE RAIL |
| Парткод: | 2AR07810 |
| Деталь: | REAR PIN, CASSETTE RAIL |
| Парткод: | 2AR07820 |
| Деталь: | EDGING, EDS-0607M (KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | WIRE SADDLE, YMC-10-0 (KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | LOWER RIGHT REINFORCEMENT ASSY |
| Парткод: | 2AR00020 |
| Деталь: | LOWER RIGHT REINFORCEMENT |
| Парткод: | 2AR02050 |
| Деталь: | UPPER PLATE FIXING |
| Парткод: | 2BL02100 |
| Деталь: | UPPER PLATE DRUM |
| Парткод: | 2BL02060 |
| Деталь: | LOWER PLATE CONT |
| Парткод: | 2BL02130 |
| Деталь: | LOWER BASE LSU |
| Парткод: | 2BL02050 |
| Деталь: | HOLDER, CASSETTE STOPPER |
| Парткод: | 77906291 |
| Деталь: | HANDLE MACHINE |
| Парткод: | 2BL02140 |
| Деталь: | SPRING BYPASS RET |
| Парткод: | 2BL06840 |
| Деталь: | BASE RUBBER |
| Парткод: | 2AR02180 |
| Деталь: | UPPER RIGHT PLATE |
| Парткод: | 2BL02120 |
| Деталь: | RIGHT HANDLE MACHINE |
| Парткод: | 2BL02180 |
| Деталь: | MOUNT RIGHT HANDLE |
| Парткод: | 2BL02150 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BL06590 |
| Деталь: | MOUNT HINGE S |
| Парткод: | 2BL04470 |
| Деталь: | GROUND PLATE MIDDLE |
| Парткод: | 2BL06410 |
| Деталь: | COVER, CASSETTE RAIL |
| Парткод: | 2AR07720 |
| Деталь: | MOUNT REAR COVER |
| Парткод: | 2BL02200 |
| Деталь: | PIN HANDLE |
| Парткод: | 2BL02170 |
| Деталь: | PAPER FEED DRAWER ASSY |
| Парткод: | 2AR00610 |
| Деталь: | MOUNT, PAPER FEED DRAWER |
| Парткод: | 2AR07710 |
| Деталь: | JUNCTION WIRING, PRIMARY PAPER FEED UNIT |
| Парткод: | 2AR27600 |
| Деталь: | RETAINING PIN, DRAWER |
| Парткод: | 33927450 |
| Деталь: | RECEPTACLE, QR/P15-8S-C (02) (HIROSE) |
| Парткод: | J0464080 |
| Деталь: | PARTS,DRUM UNIT KME36,SP |
| Парткод: | 2BK93031 |
| Деталь: | PARTS,DRUM UNIT KME50,SP |
| Парткод: | 2BL93021 |
| Деталь: | PARTS, LAMP CLEANING ASSY |
| Парткод: | 2BL93420 |
| Деталь: | SPONGE LOWER SEAL |
| Парткод: | 2BL18560 |
| Деталь: | HANDLE DRUM |
| Парткод: | 2BL18320 |
| Деталь: | GEAR SPIRAL 16 |
| Парткод: | 2BL18160 |
| Деталь: | GEAR IDLE 15 |
| Парткод: | 2BL18170 |
| Деталь: | BUSHING DRUM A |
| Парткод: | 2BL18630 |
| Деталь: | BLADE CLEANING |
| Парткод: | 2BL18300 |
| Деталь: | LOWER SEAL CLEANING |
| Парткод: | 2BL18070 |
| Деталь: | PARTS, CLAW SEPARATION |
| Парткод: | 2BL93311 |
| Деталь: | PARTS MAIN -C,MC700 |
| Парткод: | 2BL93091 |
| Деталь: | GEAR CL ROLLER 15 |
| Парткод: | 2BL18870 |
| Деталь: | GEAR CL ROLLER 16 |
| Парткод: | 2BL18880 |
| Деталь: | LABEL DRUM |
| Парткод: | 2BL05080 |
| Деталь: | GUIDE DU FEED R |
| Парткод: | 2BL21350 |
| Деталь: | MOUNT TRAY EJECT |
| Парткод: | 2FG02010 |
| Деталь: | MOUNT HINGE |
| Парткод: | 2BL04220 |
| Деталь: | COVER EXIT LOW |
| Парткод: | 2BL04100 |
| Деталь: | PARTS, OPERATION ASSY |
| Парткод: | 2FH93070 |
| Деталь: | PANEL PWB ASSY /B09/10 PANEL PWB |
| Парткод: | 2FH68040 |
| Деталь: | LOWER COVER KEY |
| Парткод: | 2BL04240 |
| Деталь: | KEY OPERATION A |
| Парткод: | 2BL04260 |
| Деталь: | KEY OPERATION B |
| Парткод: | 2BL04270 |
| Деталь: | KEY OPERATION C |
| Парткод: | 2BL04280 |
| Деталь: | KEY OPERATION D |
| Парткод: | 2BL04050 |
| Деталь: | LEVER CONT RELEASE |
| Парткод: | 2BL04200 |
| Деталь: | INNER RIGHT COVER |
| Парткод: | 2BL04090 |
| Деталь: | TRAY EJECT |
| Парткод: | 2BL04040 |
| Деталь: | Right front cover |
| Парткод: | 2FH04010 |
| Деталь: | Right front cover |
| Парткод: | 2FJ04010 |
| Деталь: | FRONT COVER MIDDLE K |
| Парткод: | 2BJ04600 |
| Деталь: | MAGNET CATCH |
| Парткод: | 60804120 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 2BL04330 |
| Деталь: | FRONT HINGE COVER P |
| Парткод: | 2BL04350 |
| Деталь: | PIN COVER HINGE |
| Парткод: | 2BL04190 |
| Деталь: | LEFT COVER CASSETTE |
| Парткод: | 2BL04150 |
| Деталь: | Left front cover |
| Парткод: | 2BL04010 |
| Деталь: | Rear Left Cover |
| Парткод: | 2BL04120 |
| Деталь: | FRONT LEFT COVER |
| Парткод: | 2BL04110 |
| Деталь: | LID COVER LEFT |
| Парткод: | 2BL04300 |
| Деталь: | RIGHT COVER |
| Парткод: | 2BL04131 |
| Деталь: | REAR COVER |
| Парткод: | 2BL04071 |
| Деталь: | PARTS, UPPER COVER KEY ASY |
| Парткод: | 2BL93330 |
| Деталь: | PARTS, UPPER COVER KEY FR |
| Парткод: | 2BL93340 |
| Деталь: | PARTS, UPPER COVER KEY IT |
| Парткод: | 2BL93350 |
| Деталь: | COVER LCD |
| Парткод: | 2BL04250 |
| Деталь: | COVER LCD I |
| Парткод: | 2BL04810 |
| Деталь: | COVER LCD F |
| Парткод: | 2BL04830 |
| Деталь: | UPPER COVER KEY |
| Парткод: | 2BL04230 |
| Деталь: | UPPER COVER KEY I |
| Парткод: | 2BL04800 |
| Деталь: | UPPER COVER KEY F |
| Парткод: | 2BL04820 |
| Деталь: | FILM OPERATION |
| Парткод: | 2BL04960 |
| Деталь: | FILM OPERATION I |
| Парткод: | 2BL04970 |
| Деталь: | FILM OPERATION F |
| Парткод: | 2BL04980 |
| Деталь: | STOPPER PAPER C |
| Парткод: | 2BK04030 |
| Деталь: | STOPPER PAPER P |
| Парткод: | 2BL04400 |
| Деталь: | PIN COVER HINGE S |
| Парткод: | 2BL04840 |
| Деталь: | FRONT COVER HINGE S |
| Парткод: | 2BL04480 |
| Деталь: | LABEL SEP CLEANING |
| Парткод: | 2BL05070 |
| Деталь: | LABEL CONVEYING JAM |
| Парткод: | 2BL05120 |
| Деталь: | BRUSH CLEANER ASSY |
| Парткод: | 5AAVBRUSH036 |
| Деталь: | COVER FLYWHEEL |
| Парткод: | 2BL04710 |
| Деталь: | LEFT TOP COVER |
| Парткод: | 2BL04170 |
| Деталь: | WIRE OPE FRONT (P) |
| Парткод: | 2BL27270 |
| Деталь: | STOPPER PAPER SUB |
| Парткод: | 2BK04040 |
| Деталь: | FILM HINGE |
| Парткод: | 2BL04880 |
| Деталь: | REAR TOP COVER |
| Парткод: | 2BL04181 |
| Деталь: | RIGHT TOP COVER |
| Парткод: | 2BL04210 |
| Деталь: | TRAY SUB C |
| Парткод: | 2BK04020 |
| Деталь: | TRAY SUB |
| Парткод: | 2BL04340 |
| Деталь: | PIN COVER |
| Парткод: | 2BL04410 |
| Деталь: | CORE 7-15X18 |
| Парткод: | 33927590 |
| Деталь: | SPONGE FRONT |
| Парткод: | 2BL06620 |
| Деталь: | MOUNT OZONE FILTER B |
| Парткод: | 2FG23040 |
| Деталь: | FILTER OZONE B |
| Парткод: | 2FG23050 |
| Деталь: | PW.BOARD ASSY KP-5132 MAIN |
| Парткод: | 2FJ01010 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | 5AAPRLGG4046AH |
| Деталь: | ENGINE PWB ASSY /B10(IN) ENGINE PWB |
| Парткод: | 2FH68030 |
| Деталь: | ENGINE PWB ASSY /B10(CM) ENGINE PWB |
| Парткод: | 2FH68020 |
| Деталь: | CORE 6-18X34 |
| Парткод: | 2BL27650 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | WIRE BYPASS FEED PI |
| Парткод: | 2BL27290 |
| Деталь: | RECEPTACLE,QR/P15-8S-C(02)(HIROSE) |
| Парткод: | J0464080 |
| Деталь: | RETAINING PIN,DRAWER |
| Парткод: | 33927450 |
| Деталь: | MOUNT DRUM DRAWER |
| Парткод: | 2BL26200 |
| Деталь: | RECEPTACLE,9715S-10A(I RS) |
| Парткод: | J7340100 |
| Деталь: | WIRE SADDLE, WS-2NS |
| Парткод: | 49513902 |
| Деталь: | WIRE SADDLE,YMC-10-0(KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | MOUNT MAIN PCB |
| Парткод: | 2FH26011 |
| Деталь: | SPACER,KGLS-4S |
| Парткод: | M2108120 |
| Деталь: | CASSETTE SWITCH ASSY |
| Парткод: | 2AR00150 |
| Деталь: | MOUNT,CASSETTE SWITCH |
| Парткод: | 2AR07170 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | MOUNT POWER PCB |
| Парткод: | 2FG26010 |
| Деталь: | POWER SOURCE PCB (100) |
| Парткод: | 2FG28021 |
| Деталь: | POWER SOURCE PCB (200) |
| Парткод: | 2FG28032 |
| Деталь: | SHIELD SUBWIRE |
| Парткод: | 2BJ26210 |
| Деталь: | MOUNT OPTION I/F (E) |
| Парткод: | 2BJ26100 |
| Деталь: | WIRE SADDLE, WS-2WS |
| Парткод: | 49829401 |
| Деталь: | CASE,54082-1215(MOLEX) |
| Парткод: | J0326120 |
| Деталь: | WIRE FINISHER GND |
| Парткод: | 2BL27280 |
| Деталь: | WIRE FG.FINISHER |
| Парткод: | 2AC27880 |
| Деталь: | WIRE OPTION(P) |
| Парткод: | 2FH27020 |
| Деталь: | MOUNT, DECK CONN ECTOR |
| Парткод: | 2AR26340 |
| Деталь: | SPACER,KGPS-6RF(KITAGAWA) |
| Парткод: | M2108670 |
| Деталь: | GUID CF CARD |
| Парткод: | 2BM26020 |
| Деталь: | EDGING,EDS-25L(KITAGAWA) |
| Парткод: | M2104280 |
| Деталь: | MOUNT FIXING DRAWER |
| Парткод: | 2BL26290 |
| Деталь: | WIRE DRAWER |
| Парткод: | 2BL27030 |
| Деталь: | WIRE PRIMARY (P) |
| Парткод: | 2FH27030 |
| Деталь: | PIN TERMINAL |
| Парткод: | 2BL26060 |
| Деталь: | SPRING TERMINAL |
| Парткод: | 2BL26070 |
| Деталь: | SPRING TERMINAL T |
| Парткод: | 2BL26270 |
| Деталь: | CASE HIGH VOLTAGE |
| Парткод: | 2BL26051 |
| Деталь: | GROUND PLATE HV |
| Парткод: | 2BL26080 |
| Деталь: | HIGH VOLTAGE PCB |
| Парткод: | 2BL28051 |
| Деталь: | WIRE HIGH VOLTAGE(P) |
| Парткод: | 2BL27070 |
| Деталь: | GASKET PRINTER A |
| Парткод: | 3H826010 |
| Деталь: | WIRE FRONT(P) |
| Парткод: | 2BL27140 |
| Деталь: | EDGING,EDS-2 |
| Парткод: | M2104210 |
| Деталь: | LEFT MOUNT I/L |
| Парткод: | 2BL26110 |
| Деталь: | SWITCH INTERLOCK |
| Парткод: | 2FG27120 |
| Деталь: | SWITCH,INTERLOCK |
| Парткод: | 2AR27040 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | LEFT WORK PLATE I/L |
| Парткод: | 2BL26120 |
| Деталь: | SWITCH,MAIN |
| Парткод: | 2BL27430 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 2BM27890 |
| Деталь: | FRONT MOUNT COVER |
| Парткод: | 2BL04060 |
| Деталь: | INNER LEFT COVER |
| Парткод: | 2BL04080 |
| Деталь: | TONER SW ASSY |
| Парткод: | 2BL01160 |
| Деталь: | CASE,BU05P-TR-PC-H(JST) |
| Парткод: | J5016050 |
| Деталь: | WIRE TONER DISPOSAL |
| Парткод: | 2BL27250 |
| Деталь: | RAIL OPTION A |
| Парткод: | 2BL26210 |
| Деталь: | RAIL OPTION B |
| Парткод: | 2BL26220 |
| Деталь: | GROUND PLATE INNER L |
| Парткод: | 2BL04450 |
| Деталь: | SHEET RADIATOR |
| Парткод: | 3H827010 |
| Деталь: | FAN MOTOR 3 |
| Парткод: | 2FG27140 |
| Деталь: | PW.B ASSY KP-893 /FLASH DIMM B10 FS36 |
| Парткод: | 2FH01960 |
| Деталь: | SHIELD |
| Парткод: | 2FH26020 |
| Деталь: | SPACER WIRE |
| Парткод: | 2BL04460 |
| Деталь: | SHAFT I/L |
| Парткод: | 2BL26280 |
| Деталь: | FUSE,237010(LITTEL) |
| Парткод: | M1660010 |
| Деталь: | PLATE OPTION |
| Парткод: | 3BH26020 |
| Деталь: | PIN OPTION |
| Парткод: | 3BH26030 |
| Деталь: | MOUNT CONNECTOR |
| Парткод: | 2BL26190 |
| Деталь: | RAIL MAIN PCB |
| Парткод: | 2BL26180 |
| Деталь: | WIRE PAPER FEED(P) |
| Парткод: | 2BL27010 |
| Деталь: | UPPER SHIELD |
| Парткод: | 2BL26020 |
| Деталь: | WIRE OPE INNER(P) |
| Парткод: | 2BL27260 |
| Деталь: | WIRE OPE REAR(P) |
| Парткод: | 2BL27090 |
| Деталь: | COVER POWER PCB |
| Парткод: | 2BL26260 |
| Деталь: | POWER CORD (120) |
| Парткод: | 19527400 |
| Деталь: | MOUNT INLET CORD 230 |
| Парткод: | 2BL26250 |
| Деталь: | INLET ASSY |
| Парткод: | 2FG01090 |
| Деталь: | FERRITE CORE |
| Парткод: | 63827080 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | POWER CODE AS(240) |
| Парткод: | 29927231 |
| Деталь: | POWER CODE GB |
| Парткод: | 79327580 |
| Деталь: | POWER CODE 110 |
| Парткод: | 65027600 |
| Деталь: | MOUNT FILTER PCB |
| Парткод: | 2FH26030 |
| Деталь: | WIRE FILTER PCB |
| Парткод: | 2FG27370 |
| Деталь: | NOISE FILTER PCB 100 |
| Парткод: | 2FG28121 |
| Деталь: | NOISE FILTER PCB 200 |
| Парткод: | 2FG28131 |
| Деталь: | SPACER,KGLS-5RT |
| Парткод: | M2108920 |
| Деталь: | SHIELD CF |
| Парткод: | 3H826050 |
| Деталь: | CORE ATFC-16-8-16 |
| Парткод: | 2FG27640 |
| Деталь: | GASKET LID PRINTER |
| Парткод: | 2FG27520 |
| Деталь: | SHIELD A GASKET |
| Парткод: | 3CR27010 |
Коды ошибок
0100
0110
0420
0440
0470
1010
1020
1030
1040
1100
1110
1120
1130
2000
2500
2600
4000
4010
4200
5300
6000
6020
6050
6400
6410
6420
7300
7400
7410
7450
7800
7810
8010
8030
8140
8170
8180
8210
8220
8300
8310
8320
8330
8340
8350
8360
8370
8380
8390
8400
8410
8420
8430
8440
8450
8460
8470
8480
F0
F010
F020
F030
F040
F080
Описание
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0110 |
| Description: | Input value from Linear Encoder is not changed by the Linear Encoder origin setup. When Motor stops during printing, expected movement is not completed on some head. |
| Causes: | Read error of Linear Encoder. Read error of Encoder on Scan Motor side. Belt is not fixed to Head Carriage firmly. |
| Remedy: | Confirm whether Encoder Scale is between the slit of Encoder Module in a whole width of the machine. Check cable connection between Linear Encoder Board and Head Board Confirm connection between Belt and Carriage Linear Encoder replacement Scan Motor replacement Servo Board replacement Main Board replacement |
| Error code: | 0420 |
| Description: | Paper feeder communication error Communication error between control PWB and optional paper feeder. |
| Causes: | Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF main-PWB. |
| Remedy: | Improper installation paper feeder. Follow installation instruction carefully again. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective control PWB. Replace the control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder). Defective PF main- PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 0440 |
| Description: | Communication error between printer and document finisher/ mailbox sorter • The CPU (U2) of engine controller PWB (KP-992) does not communicate with the DF-31 document finisher/SO-30 mailbox sorter normally. • The ASIC (U8) of engine controller PWB (KP-992) does not communicate to the DF-31 document finisher/SO-30 mailbox sorter normally. |
| Causes: | Defective engine controller PWB (KP-992). Defective main PWB of DF-31 document finisher/SO-30 mailbox sorter. Defective paper feeder/options relay PWB (KP-995). Defective signal cable between printer and DF-31 document finisher/ SO-30 mailbox sorter. Defective harness (2CK2719) between engine controller PWB (KP-992) and paper feeder/options relay PWB (KP- 995), or poor contact of the connector terminals. Defective document finisher interface PWB. Defective harness (2CK2727) between document finisher interface PWB and engine controller PWB (KP- 992), or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the main PWB of DF-31 document finisher/SO-30 mailbox sorter. See DF-31 document finisher/SO-30 mailbox sorter’s service manual. Replace the paper feeder/options relay PWB (KP-995). Replace the signal cable between printer and DF-31 document finisher/SO-30 mailbox sorter. Check the continuity of the harness (2CK2719). Check the insertion of connectors. Replace the document finisher interface PWB. Check the continuity of the harness (2CK2727). Check the insertion of connectors. |
| Error code: | 0470 |
| Description: | Switchback unit communication problem • Communication errors from the communication microcomputer on the engine controller PWB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine controller PWB. Defective switchback unit main board. |
| Remedy: | Check the connection of connectors YC3 on the engine controller PWB and the continuity across the connector terminals. Repair or replace if necessary. Replace the engine controller PWB and check for correct operation. Replace the switchback unit main board and check for correct operation. |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1040 |
| Display: | GL2: W0501 The memory is full. |
| Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1100 |
| Display: | Prepare for maint cart replacement. |
| Description: | Paper Jam There is paper jammed in the All-In-One. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Clear the paper jam, and resend the print job. |
| Error code: | 1110 |
| Description: | PF lift motor 2 error (large capacity feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 2 is turned on is excluded from detection. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 2 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF Lift motor2. PF Lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor 2 and PF main PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the PF Lift sensor 2. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1120 |
| Description: | Paper feeder left lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 1 does not turn on within 30 s of paper feeder lift motor 2 turning on. |
| Causes: | Poor contact in the connector terminals. Defective paper feeder lift switch 1. Defective paper feeder lift motor 2. The paper feeder left lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper feeder lift switch 1. Check if YC5-4 on the paper feeder main PWB goes low when paper feeder lift switch 1 is turned off. If not, replace paper feeder lift switch 1. Defective paper feeder lift motor 2. Check for continuity across the coil. If none, replace paper feeder lift motor 2. The paper feeder left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | 1130 |
| Description: | Paper feeder right lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 2 does not turn on within 30 s of paper feeder lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective paper feeder lift switch 2. Defective paper feeder lift motor 1. The paper feeder right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper feeder lift switch 2. Check if YC5-7 on the paper feeder main PWB goes low when paper feeder lift switch 2 is turned off. If not, replace paper feeder lift switch 2. Defective paper feeder lift motor 1. Check for continuity across the coil. If none, replace paper feeder lift motor 1. The paper feeder right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 4000 |
| Display: | Supplies Drum End Soon. |
| Description: | Command Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 4010 |
| Description: | Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and engine PWB (YC11) Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 4200 |
| Display: | Supplies Replace Drum |
| Description: | BD steady-state error The BD signal is not detected. |
| Causes: | APC PWB (LSU). Main/Engine PWB. |
| Remedy: | APC PWB (LSU) 1. Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in. Laser scanner unit and main/engine PWB (YC2010) 2. If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring. 3. Replace the laser scanner unit. Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. |
| Error code: | 5300 |
| Description: | Eraser lamp broken detection • The current at the correct level is not detected when ASIC (U8) on the engine controller PWB (KP-992) generates the signal to activate the eraser lamp. |
| Causes: | Defective engine controller PWB (KP-992). Defective drum unit (eraser lamp or drum PWB [KP- 813]). Defective harness (2BM2864) between engine controller PWB (KP-992) and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the drum unit. Check the continuity of the harness (2BM2864). Check the insertion of connectors. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6050 |
| Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
| Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 6410 |
| Description: | Fuser unit type mismatch problem Absence of the fuser unit is detected. |
| Causes: | Fuser unit connector inserted incorrectly. Different type of the fuser unit is installed. |
| Remedy: | Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. Different type of the fuser unit is installed. Install the correct fuser unit. |
| Error code: | 6420 |
| Description: | Fuser unit fuse cut problemctor. |
| Causes: | Poor contact in the connector terminals. Fuser unit connector inserted incorrectly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC10 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. |
| Error code: | 7300 |
| Display: | Jam Tray 1 Pull the paper tray1 completely out of the machine and remove the jammed paper. |
| Description: | Toner sensor problem • While the toner container sensor is on, the toner sensor in the developing unit does not turn on after the toner sensor turns off and toner is replenished from the toner container. |
| Causes: | Defective toner sensor. Poor contact in the toner sensor connector terminals. Defective toner container sensor. Defective toner container. |
| Remedy: | Replace the toner sensor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the toner container sensor. Replace the toner container. |
| Error code: | 7400 |
| Display: | Jam Tray 2 Pull the paper tray2 completely out of the machine and remove the jammed paper. |
| Description: | Developing unit connector insertion problem Absence of the developing unit is detected. |
| Causes: | Developing unit connector inserted incorrectly. Defective developing unit connector. |
| Remedy: | Developing unit connector inserted incorrectly. Reinsert the developing unit connector if necessary. Defective developing unit connector. Replace the developing unit. |
| Error code: | 7410 |
| Description: | Drum unit connector insertion problem Absence of the drum unit is detected.c |
| Causes: | Drum unit connector inserted incorrectly. Defective drum unit connector. |
| Remedy: | Drum unit connector inserted incorrectly. Reinsert the drum unit connector if necessary. Defective drum unit connector. Replace the drum unit. |
| Error code: | 7450 |
| Description: | Developing unit fuse cut problem • The developer unit fuse cannot be cut.it co |
| Causes: | Developing unit connector inserted incorrectly. Defective developing unit connector. |
| Remedy: | Reinsert the developing unit connector if necessary. Replace the developing unit. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 8010 |
| Description: | Punch motor error 1 When the punch motor is driven, punch home position sensor does not turn on within 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch home position sensor. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch home position sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch home position sensor and Punch PWB (YC8) 4. Replace the Punch home position sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8030 |
| Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8170 |
| Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8180 |
| Description: | DF side registration motor 1 error 2 JAM6810 (jam in front of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1. 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8220 |
| Description: | Stapler shift motor 2 error (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3.5 s passed. |
| Causes: | Poor contact in the connector terminals. Defective stapler shift motor 2. Defective finisher main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC10 on the finisher main PWB and the connector of stapler shift motor 2, and the continuity across the connector terminals. Repair or replace if necessary. Defective stapler shift motor 2. Replace stapler shift motor 2. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | 8300 |
| Description: | CF unit communication error Communication with the center- folding unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF set sensor. Defective PWB. |
| Remedy: | CF unit set switch 1. Execute U241 Booklet - Set to check the finisher switch. 2. Check that the switch and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main PWB (YC7) and DF main PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CF unit set switch. CF main PWB Replace the CF main PWB DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8310 |
| Description: | CF side registration motor 2 error When initial operation, CF side registration sensor 2 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 2. Defective CF side registration motor 2. Defective CF main PWB. |
| Remedy: | CF side registration motor 2 1. Execute U240 Booklet - Width Test to check finisher operation check. 2. Manipulate the side registration upper guide back and forth to check it can smoothly move back and forth. 3. Check that the drive from the motor reaches the side registration upper guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor. CF side registration sensor 2 1. Execute U241 Booklet - Width Up HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 2 and CF main PWB (YC20) 4. Replace the CF side registration sensor 2. CF main PWB Replace the CF main PWB |
| Error code: | 8320 |
| Description: | CF adjustment motor error When initial operation, CF adjustment sensor does not turn on within 2.5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF adjustment sensor 1, 2. Defective CF adjustment motor 1, 2. Defective CF main PWB. |
| Remedy: | CF adjustment motor1,2 1. Execute U240 Booklet - Bundle Up / Down to check the finisher operation. 2. Manipulate the fold moving belt up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold moving belt. (Check if the belt is bent.) 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment motor 1,2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF adjustment motor1,2 CF adjustment sensor1,2 1. Execute U241 Booklet - bundle Up / Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment sensor 1,2 and CF main PWB (YC20) 4. Replace the CF adjustment sensor1,2. CF main PWB Replace the CF main PWB. |
| Error code: | 8330 |
| Description: | CF blade motor error When initial operation, CF blade sensor does not turn on within 1500 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF blade sensor. Defective CF blade motor. Defective CF main PWB. |
| Remedy: | CF blade motor 1. Execute U240 Booklet - Blade to check the finisher operation. 2. Manipulate the fold blade up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold blade. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade motor and CF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF blade motor. CF blade sensor 1. Execute U241 Booklet - Blade HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade sensor and CF main PWB (YC20) 4. Replace the CF blade sensor. CF main PWB Replace the CF main PWB |
| Error code: | 8340 |
| Description: | CF staple motor error 1 Staple JAM (center-folding unit) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF staple sensor. Defective CF staple motor. Defective CF main PWB. |
| Remedy: | CF staple motor 1. Execute U240 Booklet - Staple to check the finisher operation. 2. Manipulate the staple up and down check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF staple unit and CF main PWB (YC13) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF staple motor. CF staple sensor Replace the CF staple unit. CF main PWB Replace the CF main PWB. |
| Error code: | 8350 |
| Description: | CF side registration motor 1 error When initial operation, CF side registration sensor 1 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 1. Defective CF side registration motor 1. Defective CF main PWB |
| Remedy: | CF side registration motor 1 1. Execute U240 Booklet - Width Test to check the finisher operation. 2. Manipulate the side registration lower guide back and forth to check it can smoothly operable. 3. Check that the drive from the motor reaches the side registration lower guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 1 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor 1. CF side registration sensor 1 1. Execute U241 Booklet - Width Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 1 and CF main PWB (YC20) 4. Replace the CF side registration sensor 1. CF main PWB Replace the CF main PWB |
| Error code: | 8360 |
| Description: | CF main motor error During driving the motor, the lock signal is detected for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF main motor. Defective CF main PWB. |
| Remedy: | CF main motor 1. Execute U240 Booklet - Folding to check the finisher operation. 2. Manipulate the conveying roller to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main motor and CF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF main motor. CF main PWB Replace the CF main PWB |
| Error code: | 8370 |
| Description: | CF staple motor error 2 (4000-sheet finisher) Staple JAM (DF) has been detected twice in a row. (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF staple motor. Defective CF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF staple unit and CF main PWB (YC13) Defective CF staple motor. Replace the CF staple unit. Defective CF main PWB. Replace the CF main PWB and check for correct operation. |
| Error code: | 8380 |
| Description: | Booklet stitcher folding problem |
| Causes: | A problem is detected with the folding sensor. |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | 8390 |
| Description: | Booklet stitcher backup RAM data problem |
| Causes: | A backup RAM data error is detected. |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | 8400 |
| Description: | Booklet stitcher incorrect type problem |
| Causes: | An incorrect type error is detected. |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | 8410 |
| Description: | Punch slide motor error 1 The punch slide sensor won’t turn On when home position has been moved by 30 mm. |
| Causes: | Defective connector cable or poor contact in the connector. Defective slide sensor. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch slide sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide sensor and Punch PWB (YC6) 4. Replace the punch slide sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8420 |
| Description: | Punch slide motor error 2 In detection of paper edges, the paper edge cannot be detected in 30 mm move. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch paper edge sensor 1,2 1. Execute U241 Punch - Edge Face 1,2,3,4 to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch paper edge sensor 1,2 and Punch PWB (YC5,YC7) 4. Replace the punch paper edge sensor 1,2. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8430 |
| Description: | Punch unit communication error Communication with the punch unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8440 |
| Description: | Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range. |
| Causes: | The paper entry sensor connector makes poor contact. Defective paper entry sensor. The optical path of the paper entry sensor is blocked by foreign matter. Defective finisher main PWB. |
| Remedy: | The paper entry sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective paper entry sensor. Replace the paper entry sensor and check for correct operation. The optical path of the paper entry sensor is blocked by foreign matter. Remove the foreign matter. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | 8450 |
| Description: | Booklet stitcher side punch sensor problem |
| Causes: | A problem is detected with the side punch sensor. |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | 8460 |
| Description: | EEPROM problem (document finisher) Reading from or writing to EEPROM cannot be performed. |
| Causes: | Defective EEPROM or DF main PWB. |
| Remedy: | Replace the DF main PWB and check for correct operation. |
| Error code: | 8470 |
| Description: | Booklet stitcher punch dust sensor problem |
| Causes: | A problem is detected with the punch dust sensor |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | 8480 |
| Description: | Booklet stitcher broken punch power source wire problem |
| Causes: | A broken punch power source wire problem is detected. |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | F0 |
| Display: | SVC F0 ERROR |
| Description: | The communication ended because of a WDT due to an overrun of the software. |
| Causes: | Defective main controller PWB. Defective operator panel PWB. Defective mainengine controllers relay PWB. Defective engine controller PWB . Defective harness between engine controller PWB and operator panel PWB, or poor contact of the connector terminals. |
| Remedy: | Attempt the communication again. If the error occurs frequently, perform a memory clear (except user area.) |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F030 |
| Description: | Main PWB system error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F080 |
| Description: | Flash ROM error (during download) |
| Causes: | Defective flash ROM. |
| Remedy: | Defective flash ROM. Replace the engine PWB and check for correct operation. |
