Kyocera ECOSYS FS-C8026N
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
100000
Скорость печати
A4
26
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Макс. формат |
A3 |
Область применения |
большой офис |
Число страниц в месяц |
100 000 |
Размещение |
настольный |
Цветность печати |
цветная |
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Тип устройства |
Принтер |
Факс |
|
Сканер |
|
Копир |
|
Печать фотографий |
|
Телефон |
|
Принтер |
|
Печать без полей |
|
Двусторонняя печать |
|
Прямая печать |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
| По X | 600 |
| По Y | 600 |
Скорость ч/б печати |
|
| A4 | 13 |
| A4 | 26 |
Время выхода первого отпечатка |
|
| Ч/б | 9 |
Расходные материалы |
|
Ресурс цветного картриджа/тонера |
20 000 |
Ресурс ч/б картриджа/тонера |
20 000 |
Количество картриджей |
4 |
Печать на: |
|
| Глянцевой бумаге |
|
| Этикетках |
|
| Карточках |
|
| Матовой бумаге |
|
| Конвертах |
|
| Фотобумаге |
|
| Пленках |
|
| CD/DVD |
|
| Рулоне |
|
Плотность бумаги |
|
| Максимальная | 216 |
| Минимальная | 60 |
Телефон |
|
Спикерфон |
|
Проводная трубка |
|
Беспроводная трубка |
|
АОН |
|
Caller ID |
|
Автоответчик |
|
Стандарт DECT |
|
Шрифты и языки управления |
|
Языки управления |
|
| PostScript 3 |
|
| PostScript |
|
| PCL 6 |
|
|
|
|
| PCL 5e |
|
| PCL 5c |
|
| PPDS |
|
| PostScript 2 |
|
Количество установленных шрифтов |
|
| PCL | 80 |
Лотки |
|
Подача бумаги |
|
| Максимальная | 4 150 |
| Стандартная | 650 |
Вывод бумаги |
|
| Стандартный | 500 |
Финишер |
|
Сортер |
|
Электронная сортировка |
|
Брошюровщик |
|
Степлер |
|
Сортировка со сдвигом |
|
Интерфейсы |
|
LPT |
|
Ethernet (RJ-45) |
|
USB |
|
Количество свободных слотов расширения |
1 |
Устройство для чтения карт памяти |
|
FireWire (IEEE 1394) |
|
RS-232 |
|
Инфракрасный порт |
|
Bluetooth |
|
Wi-Fi |
|
Версия USB |
2,0 |
Память/Процессор |
|
Макс, объем памяти |
512 |
Частота процессора |
600 |
Объем памяти |
128 |
Процессор |
PowerPC 750СХ |
Дополнительная информация |
|
Мин. системные требования |
Intel Pentium II |
Поддержка ОС |
|
| Mac OS |
|
| Windows |
|
| DOS |
|
| Linux |
|
Потребляемая мощность |
|
| При работе | 700 |
| В режиме ожидания | 165 |
Уровень шума |
|
| При работе | 53 |
| В режиме ожидания | 38 |
Габариты |
|
Вес |
84 |
Высота |
463 |
Ширина |
699 |
Глубина |
715 |
Модули
PAPER FEED UNIT 2
Electrical Components 1
PAPER CASSETTE
Primarry Transfer Unit
Option 2 (AK-640A)
Exit Unit 2
Upper Frame Unit 1
Option 1 (PT-640)
Drive Units 1
FUSER UNIT
Primarry Feed Assembly
Option 3 (AK-640B)
OPERATION UNIT
Process Unit
ELECTRICAL COMPONENTS 2
Upper Frame Unit 2
Exterior Covers
Paper feed unit 1
Drive Units 2
Exit Unit 1
Детали Exit Unit 1
| Деталь: | FEED UNIT ASSY |
| Парткод: | 2BF00092 |
| Деталь: | COVER MPF TRAY |
| Парткод: | 2BG06511 |
| Деталь: | PLATE MPF |
| Парткод: | 2BG06810 |
| Деталь: | TRAY MPF B |
| Парткод: | 2BF06011 |
| Деталь: | COVER SWITCH |
| Парткод: | 2BG06820 |
| Деталь: | TRAY MPF A |
| Парткод: | 2BG06581 |
| Деталь: | TRAY MPF C |
| Парткод: | 2BG06600 |
| Деталь: | GUIDE PAPER MPF |
| Парткод: | 2BG06210 |
| Деталь: | ACTUATOR CAM MPF |
| Парткод: | 2BM07050 |
| Деталь: | SPRING RETARD MPF |
| Парткод: | 5MMW266LD009 |
| Деталь: | RETARD ROLL MPF ASSY |
| Парткод: | 2BM07400 |
| Деталь: | HOLDER RETARD MPF |
| Парткод: | 2BM07280 |
| Деталь: | RETARD ROLL ASSY |
| Парткод: | 2BM07340 |
| Деталь: | COVER PWB MPF B |
| Парткод: | 2BG06130 |
| Деталь: | PT.SENSOR GP2S30 |
| Парткод: | 5SP24BW52E++040 |
| Деталь: | WIRE,BYPASS UPPER LOWER |
| Парткод: | 2BG27531 |
| Деталь: | LABET TC |
| Парткод: | 2BG05090 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | WIRE,FEED UNIT |
| Парткод: | 2BG27620 |
| Деталь: | BRACKET MPF DRIVE |
| Парткод: | 2BG06680 |
| Деталь: | SOLENOID MPF |
| Парткод: | 2BM27100 |
| Деталь: | GEAR Z28S-Z30S |
| Парткод: | 2BG06760 |
| Деталь: | BRACKET MPF DRAWER |
| Парткод: | 2BG06670 |
| Деталь: | SHAFT ROLL MPF |
| Парткод: | 2BG06090 |
| Деталь: | CLUTCH MPF ASSY |
| Парткод: | 5AAVCLTCH020 |
| Деталь: | CLUTCH 26-B |
| Парткод: | 5EYYAFAAD01++02 |
| Деталь: | BUSH POM B |
| Парткод: | 2BM07320 |
| Деталь: | PLATE LIFT MPF |
| Парткод: | 2BG06520 |
| Деталь: | PAD FRICTION |
| Парткод: | 2BM07170 |
| Деталь: | CURSOR MPF F |
| Парткод: | 2BG06550 |
| Деталь: | CURSOR MPF R |
| Парткод: | 2BG06540 |
| Деталь: | GEAR MANUAL40301X1013 |
| Парткод: | 2B700380 |
| Деталь: | PLATE MPF UP |
| Парткод: | 2BG06530 |
| Деталь: | FRAME MPF |
| Парткод: | 2BG06390 |
| Деталь: | LOCK TRAY MPF |
| Парткод: | 2BG06020 |
| Деталь: | ACTUATOR PAPER MPF |
| Парткод: | 2BM07060 |
| Деталь: | BYPASS PCB ASSY |
| Парткод: | 2BG01151 |
| Деталь: | WIRE,REG SWITCH JUNCTION |
| Парткод: | 2BG27500 |
| Деталь: | SPONGE WIRE D |
| Парткод: | 2BG06570 |
| Деталь: | BUSH METAL |
| Парткод: | 2BM07330 |
| Деталь: | ROLL FEED MPF ASSY |
| Парткод: | 5AAROLU053 |
| Деталь: | SPRING BOTTOM MPF |
| Парткод: | 2BM07080 |
| Деталь: | FRONT PCB JUNCTION ASSY |
| Парткод: | 2BG01130 |
| Деталь: | COVER DESK DRAWER |
| Парткод: | 2BG02490 |
| Деталь: | SWITCH,MAIN |
| Парткод: | 2BG27060 |
| Деталь: | WIRE,MAIN SWITCH |
| Парткод: | 2BG27180 |
| Деталь: | MINIATURE CLAMP.UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | LOCKING WIRE SADDLE,LWS-2NS |
| Парткод: | 49427223 |
| Деталь: | WIRE,DESK |
| Парткод: | 2BG27220 |
| Деталь: | WIRE,OPTION JUNCTION |
| Парткод: | 2BG27800 |
| Деталь: | WIRE,LIFT MOTOR |
| Парткод: | 2BG27330 |
| Деталь: | WIRE,COLOR DEVE MOTOR |
| Парткод: | 2BG27250 |
| Деталь: | WIRE,CLUTCH PCB |
| Парткод: | 2BG27430 |
| Деталь: | FERRITE CORE,SFT-72SN(TAKEUCHI) |
| Парткод: | M70CA010 |
| Деталь: | FERRITE CORE,SFT-59SN(TAKEUCHI) |
| Парткод: | M70C0010 |
| Деталь: | ENGINE MAIN PCB ASSY.SP |
| Парткод: | 2BF68020 |
| Деталь: | LPH DRIVE ASSY |
| Парткод: | 2BG01035 |
| Деталь: | LPH ASSY (M)(C)(Y) |
| Парткод: | 2BG00231 |
| Деталь: | LPH BK ASSY (K) |
| Парткод: | 2BG00241 |
| Деталь: | HOLDER LPH F |
| Парткод: | 2BG13020 |
| Деталь: | LABEL CAUTION LPH |
| Парткод: | 2BG05030 |
| Деталь: | PLATE EARTH LPH |
| Парткод: | 2BG13070 |
| Деталь: | DUCT MCH GUIDE |
| Парткод: | 2BG13051 |
| Деталь: | HOLDER LPH R |
| Парткод: | 2BG13030 |
| Деталь: | STAY LPH |
| Парткод: | 2BG13060 |
| Деталь: | SENSOR 12,SEPARATION (M)(C)(Y) |
| Парткод: | 3B827040 |
| Деталь: | WIRE,T EMP SW JUNCTION (M)(C)(Y) |
| Парткод: | 2BG28600 |
| Деталь: | SEAL DUCT UP |
| Парткод: | 2BG13120 |
| Деталь: | WIRE,LPH(M) |
| Парткод: | 2BG27752 |
| Деталь: | WIRE,LPH(C) |
| Парткод: | 2BG28772 |
| Деталь: | WIRE,LPH(Y) |
| Парткод: | 2BG28782 |
| Деталь: | WIRE,LPH(K) |
| Парткод: | 2BG28512 |
| Деталь: | SPRING LPH |
| Парткод: | 2BG13040 |
| Деталь: | CORE 8-16X10 |
| Парткод: | 3HK27050 |
| Деталь: | COVER DUCT MCH F |
| Парткод: | 2BG13081 |
| Деталь: | COVER DUCT MCH R |
| Парткод: | 2BG13091 |
| Деталь: | SEAL STAY LPH |
| Парткод: | 2BG13100 |
| Деталь: | STOPPER CONTAINER G |
| Парткод: | 2BF02520 |
| Деталь: | STOPPER CONTAINER H |
| Парткод: | 2BF02530 |
| Деталь: | CLAMP,EMT-4N(TAKEUCHI) |
| Парткод: | M70A5010 |
| Деталь: | SPONGE HARNESS F |
| Парткод: | 2BG02730 |
| Деталь: | WIRE,FRONT COVER SWITCH |
| Парткод: | 2BG27980 |
| Деталь: | DUCT FAN 40 |
| Парткод: | 2BG23050 |
| Деталь: | FAN 40 |
| Парткод: | 2BG23060 |
| Деталь: | WIRE,HUMIDITY SENSOR |
| Парткод: | 2BG27840 |
| Деталь: | WIRE,POWER SOURCE B |
| Парткод: | 2BG28560 |
| Деталь: | WIRE,DRUM MOTOR |
| Парткод: | 2BG27710 |
| Деталь: | DRUM DRIVE ASSY |
| Парткод: | 2BG00560 |
| Деталь: | MOTOR,DRUM |
| Парткод: | 2BG27120 |
| Деталь: | BEARING,608ZZ |
| Парткод: | 45506083 |
| Деталь: | SPRING JOINT D |
| Парткод: | 2BG22020 |
| Деталь: | JOINT DRUM |
| Парткод: | 2BG22010 |
| Деталь: | WIRE,POWER SOURCE A |
| Парткод: | 2BG27360 |
| Деталь: | WIRE,POWER SOURCE SIGNAL |
| Парткод: | 2BG27370 |
| Деталь: | WIRE,PRINTER SIGNAL |
| Парткод: | 2BG27420 |
| Деталь: | LABEL RED(M) |
| Парткод: | 2BG68160 |
| Деталь: | LABEL BLUE(C) |
| Парткод: | 2BG68170 |
| Деталь: | LABEL YELLOW(Y) |
| Парткод: | 2BG68180 |
| Деталь: | LABEL BLACK(K) |
| Парткод: | 2BG68190 |
| Деталь: | LPH |
| Парткод: | 2BG13010 |
| Деталь: | CORE 11-25X14 |
| Парткод: | 2A627930 |
| Деталь: | EEPROM,24LC256-I/P |
| Парткод: | NCQ05070 |
| Деталь: | WIRE,LPH(M) R |
| Парткод: | 2BG28821 |
| Деталь: | WIRE,LPH(C) R |
| Парткод: | 2BG28841 |
| Деталь: | WIRE,LPH(Y) R |
| Парткод: | 2BG28851 |
| Деталь: | WIRE,LPH(K) R |
| Парткод: | 2BG28831 |
| Деталь: | M4 12 CRFREE ST |
| Парткод: | 2BG02860 |
| Деталь: | WASHER M4 10 CRFREE |
| Парткод: | 2BG02870 |
| Деталь: | SHEET LPH HARNESS |
| Парткод: | 2BG13110 |
| Деталь: | PARTS,CASSETTE ASSY.SP |
| Парткод: | 2BG93011 |
| Деталь: | RACK CURSOR |
| Парткод: | 3CY06090 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 2BC07860 |
| Деталь: | RAIL A,CURSOR |
| Парткод: | 2BC06720 |
| Деталь: | CURSOR A,CASSETTE |
| Парткод: | 3CY06041 |
| Деталь: | LEVER,CASSETTE CURSOR |
| Парткод: | 33907080 |
| Деталь: | SPRING,CURSOR |
| Парткод: | 2BC06950 |
| Деталь: | LID A,CURSOR |
| Парткод: | 3CY06060 |
| Деталь: | CUSHION,CASSETTE R |
| Парткод: | 60907170 |
| Деталь: | CURSOR B,CASSETTE |
| Парткод: | 3CY06050 |
| Деталь: | LABEL,PAPER UPPER LIMIT |
| Парткод: | 61705110 |
| Деталь: | GEAR 20,CURSOR |
| Парткод: | 3CY06100 |
| Деталь: | SIZE DETECTION PCB |
| Парткод: | 33928111 |
| Деталь: | WIRE,CASSETTE UNIT |
| Парткод: | 33927210 |
| Деталь: | SHAFT,LIFT CASSETTE |
| Парткод: | 2BC06710 |
| Деталь: | WORK PLATE,LIFT CASSETTE |
| Парткод: | 2BC06090 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | RETAINER M4 |
| Парткод: | 3CY06030 |
| Деталь: | WORK PLATE,CASSETTE |
| Парткод: | 33907020 |
| Деталь: | PAD,CASSETTE |
| Парткод: | 66107100 |
| Деталь: | PIN,CASSETTE WORK PLATE |
| Парткод: | 66007310 |
| Деталь: | CURSOR C,CASSETTE |
| Парткод: | 3CY06071 |
| Деталь: | LID C,CURSOR |
| Парткод: | 3CY06080 |
| Деталь: | RAIL C,CURSOR |
| Парткод: | 33907120 |
| Деталь: | DETECTION PLATE,PAPER SIZE |
| Парткод: | 33907170 |
| Деталь: | SPRING,PAD |
| Парткод: | 66106080 |
| Деталь: | LID,PAPER SIZE DETECTION |
| Парткод: | 33907160 |
| Деталь: | GROUND PLATE,CASSETTE |
| Парткод: | 2BC07830 |
| Деталь: | PLUG,QR/P15-8S-C(HIROSE) |
| Парткод: | J0463080 |
| Деталь: | LABEL,CASSETTE |
| Парткод: | 3CY05080 |
| Деталь: | SHEET,LIFT PLATE |
| Парткод: | 3CY06110 |
| Деталь: | PARTS,CASSETTE COVER,SP |
| Парткод: | 2BG93020 |
| Деталь: | Label 1 |
| Парткод: | 2BG05070 |
| Деталь: | PLATE SIZE IN |
| Парткод: | 2BL06910 |
| Деталь: | PLATE SIZE C |
| Парткод: | 2BL06470 |
| Деталь: | PLATE NUMBER |
| Парткод: | 3CY04100 |
| Деталь: | TRANSFER ASSY |
| Парткод: | 2BF93066 |
| Деталь: | SET AK-640A(120)(OPTION) |
| Парткод: | 3B882050 |
| Деталь: | SET AK-640A(230)(OPTION) |
| Парткод: | 3B882060 |
| Деталь: | POWER CORD(120) |
| Парткод: | 19527400 |
| Деталь: | FILM,CONVEYING |
| Парткод: | 3B860560 |
| Деталь: | REAR RETAINER,SLIDER |
| Парткод: | 3B803510 |
| Деталь: | MOUNT,SLIDER |
| Парткод: | 3B803520 |
| Деталь: | JUNCTION PLATE,SLIDER |
| Парткод: | 3B803530 |
| Деталь: | JUNCTION PLATE,MACHINE |
| Парткод: | 3B803540 |
| Деталь: | MOUNT,MACHINE |
| Парткод: | 3B803550 |
| Деталь: | STOPPER,JUNCTION PLATE |
| Парткод: | 3B803560 |
| Деталь: | RAIL,RELEASE |
| Парткод: | 3B803570 |
| Деталь: | GROUND PLATE A,NOISE |
| Парткод: | 18526211 |
| Деталь: | FRONT RETAINER,SLIDER |
| Парткод: | 3B803500 |
| Деталь: | SLIDER,FINISHER |
| Парткод: | 3B803600 |
| Деталь: | HANDLE,RELEASE |
| Парткод: | 3B803610 |
| Деталь: | RETAINER M,RELEASE |
| Парткод: | 3B860510 |
| Деталь: | HOOK M,RELEASE |
| Парткод: | 3B860520 |
| Деталь: | GROUND PLATE,FIXING UNIT |
| Парткод: | 34920190 |
| Деталь: | ACTUATOR PLATE M,SAFETY SWITCH |
| Парткод: | 3B860530 |
| Деталь: | RAIL M,RELEASE |
| Парткод: | 3B860540 |
| Деталь: | JUNCTION PLATE M,RAIL |
| Парткод: | 3B860550 |
| Деталь: | OPTION BOX ASSY(120) |
| Парткод: | 2BG60080 |
| Деталь: | OPTION BOX ASSY(200) |
| Парткод: | 2BG60090 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | 49513902 |
| Деталь: | SPACER,MAIN PCB |
| Парткод: | 2A626300 |
| Деталь: | FAN,COOLING50 |
| Парткод: | 2BG27490 |
| Деталь: | OPTION POWER SUPPLY ASSY(100) |
| Парткод: | 2BG60031 |
| Деталь: | OPTION POWER SUPPLY ASSY(200) |
| Парткод: | 2BG60041 |
| Деталь: | WIRE,OPTION POWER SUPPLY |
| Парткод: | 2BG60050 |
| Деталь: | MOUNT OPTION POWER SOURCE |
| Парткод: | 2BG60060 |
| Деталь: | INLET ASSY |
| Парткод: | 2BG60200 |
| Деталь: | CORE,9-20X32 |
| Парткод: | 65027480 |
| Деталь: | BINDING TAP-TIGHT S SCREW M4X14 |
| Парткод: | B3024140 |
| Деталь: | +TP TAP-TITE S SCREW M4X20(TRIVALENT CHROMATING |
| Парткод: | BAB54200 |
| Деталь: | TRIPLE SCREW M3X5 (BLACK) |
| Парткод: | B4303050 |
| Деталь: | BINDING SCREW BVM4X6 (BLACK) |
| Парткод: | B1304060 |
| Деталь: | BINDING SCREW BVM4X10 (BLACK) |
| Парткод: | B1304100 |
| Деталь: | BINDING SCREW BVM3X5 (BLACK) |
| Парткод: | B1303050 |
| Деталь: | BINDING SCREW CVM3X5 |
| Парткод: | B1003050 |
| Деталь: | CORE SFT-72SNB-026K |
| Парткод: | 2C927230 |
| Деталь: | SHIELD GASKET F |
| Парткод: | 2BG60250 |
| Деталь: | SHIELD GASKET G |
| Парткод: | 2BG60260 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | EXIT ASSY |
| Парткод: | 2BG00432 |
| Деталь: | GUIDE EXIT(1/4) |
| Парткод: | 2BG21460 |
| Деталь: | SHEET EXIT GUIDE |
| Парткод: | 2BG21660 |
| Деталь: | SEAL EXIT B |
| Парткод: | 2BG21650 |
| Деталь: | TAPE DIS JOINT |
| Парткод: | 2BG21610 |
| Деталь: | TAPE DIS JOINT CE |
| Парткод: | 2BG21620 |
| Деталь: | DISCHARGER EXIT |
| Парткод: | 2BG21060 |
| Деталь: | SOLENOID FEED |
| Парткод: | 2BG21430 |
| Деталь: | PLATE SOLENOID |
| Парткод: | 2BG21790 |
| Деталь: | SPRING SOLENOID |
| Парткод: | 2BM17220 |
| Деталь: | STUD SCREW M3 |
| Парткод: | 2BR20470 |
| Деталь: | SPRING JOINT EXIT |
| Парткод: | 2BG21860 |
| Деталь: | PLATE GUIDE R |
| Парткод: | 2BG21710 |
| Деталь: | SPRING PULLEY FU |
| Парткод: | 2BG21290 |
| Деталь: | SHAFT PULLEY EXIT B |
| Парткод: | 2BG21090 |
| Деталь: | PULLEY EXIT |
| Парткод: | 2BG21070 |
| Деталь: | PULLEY EXIT FU |
| Парткод: | 2BG21540 |
| Деталь: | ACTUATOR FUSER EXIT |
| Парткод: | 2BG21761 |
| Деталь: | ACT FUSER DU |
| Парткод: | 2BG21260 |
| Деталь: | ROLLER EXIT SPG |
| Парткод: | 2BG21740 |
| Деталь: | BEARING.DRIVE |
| Парткод: | 2AV22410 |
| Деталь: | ROLLER EXIT E |
| Парткод: | 2BG21050 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | ROLLER EXIT C |
| Парткод: | 2BG21030 |
| Деталь: | BUSH 6 EW |
| Парткод: | 2BG22970 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | GEAR Z42 EXIT B |
| Парткод: | 2BG07430 |
| Деталь: | PULLEY SEPARATOR 23 B |
| Парткод: | 2BG07420 |
| Деталь: | GEAR Z21-Z20 EXIT |
| Парткод: | 2BG21160 |
| Деталь: | GEAR Z20 EXIT B |
| Парткод: | 2BG07410 |
| Деталь: | GUIDE CHANGE DU |
| Парткод: | 2BG21831 |
| Деталь: | WIRE,EJECT UNIT |
| Парткод: | 2BG27970 |
| Деталь: | SWITCH,PHOT0 interruptor |
| Парткод: | 2A127050 |
| Деталь: | SPONGE EXIT FRAME |
| Парткод: | 2BG21630 |
| Деталь: | SPRING EARTH JOINT |
| Парткод: | 2BG21700 |
| Деталь: | SPRING FUSER ACT DU |
| Парткод: | 2BG21490 |
| Деталь: | ACTUATOR EXIT B |
| Парткод: | 2BG21380 |
| Деталь: | SPRING ACT FU |
| Парткод: | 2BG21980 |
| Деталь: | GUIDE CHANGE FD |
| Парткод: | 2BG21821 |
| Деталь: | COVER EXIT |
| Парткод: | 2BG21230 |
| Деталь: | SEAL EXIT A |
| Парткод: | 2BG21670 |
| Деталь: | HANDLE EXIT |
| Парткод: | 2BG21960 |
| Деталь: | SEAL EXIT C |
| Парткод: | 2BG21990 |
| Деталь: | SPRING HOOK FUSER |
| Парткод: | 2BG20790 |
| Деталь: | SPRING HOOK EXIT |
| Парткод: | 2BG21550 |
| Деталь: | LABEL OPERATION LEFT |
| Парткод: | 2BG05060 |
| Деталь: | PLATE LEVER SOL |
| Парткод: | 2BM17180 |
| Деталь: | SHEET EXIT COVER |
| Парткод: | 2BG07610 |
| Деталь: | SPRING EXIT F |
| Парткод: | 2BG21470 |
| Деталь: | PLATE EXIT COVER |
| Парткод: | 2BG21300 |
| Деталь: | SPRING EXIT R |
| Парткод: | 2BG21480 |
| Деталь: | WIRE,TONER EMPTY SWITCH |
| Парткод: | 2BG27830 |
| Деталь: | FOOT |
| Парткод: | 2BG02390 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | 49513902 |
| Деталь: | HANDLE |
| Парткод: | 2BG02180 |
| Деталь: | CAP HANDLE |
| Парткод: | 2BG02470 |
| Деталь: | CAP HANDLE R |
| Парткод: | 2BG02480 |
| Деталь: | GUIDE CONTAINER Y |
| Парткод: | 2BF15030 |
| Деталь: | SPRING CONTAINER EJECT |
| Парткод: | 2BG15180 |
| Деталь: | WIRE,DUPLEX JUNCTION |
| Парткод: | 2BG27680 |
| Деталь: | SCREW A |
| Парткод: | 2BG02410 |
| Деталь: | HOLDER IMAGE R |
| Парткод: | 2BG09040 |
| Деталь: | GROUND DRAWER |
| Парткод: | 2BG02430 |
| Деталь: | PLATE CONTACT WIRE |
| Парткод: | 2BG10111 |
| Деталь: | PLATE SPRING GRID |
| Парткод: | 2BG10121 |
| Деталь: | MOUNT PAPER SIZE |
| Парткод: | 2BG06890 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | WIRE,CASSETTE LENGTH SW |
| Парткод: | 2BG27230 |
| Деталь: | RECEPTACLE,QR/P15-8S-C(02)(HIROSE) |
| Парткод: | J0464080 |
| Деталь: | WIRE,CASSETTE SIZE |
| Парткод: | 2BG27240 |
| Деталь: | SCREW B |
| Парткод: | 2BG02420 |
| Деталь: | GUIDE TC R |
| Парткод: | 2BG02610 |
| Деталь: | PULLEY RAIL B |
| Парткод: | 2BG02770 |
| Деталь: | LEVER LOCK TC R |
| Парткод: | 2BG02630 |
| Деталь: | PIN LOCK TC |
| Парткод: | 2BG02650 |
| Деталь: | SPRING COVER R |
| Парткод: | 3B706550 |
| Деталь: | LOCK COVER RIGHT |
| Парткод: | 2BL06490 |
| Деталь: | SPRING LOCK TC |
| Парткод: | 2BG02640 |
| Деталь: | SPRING EARTH RAIL |
| Парткод: | 2BG06710 |
| Деталь: | HOLDER DU DRIVE |
| Парткод: | 2BG22850 |
| Деталь: | SHEET HARNESS R |
| Парткод: | 2BG02740 |
| Деталь: | WIRE,IU JUNCTION M |
| Парткод: | 2BF27110 |
| Деталь: | WIRE,IU JUNCTION C |
| Парткод: | 2BF27120 |
| Деталь: | WIRE,IU JUNCTION Y |
| Парткод: | 2BF27130 |
| Деталь: | WIRE,IU JUNCTION K |
| Парткод: | 2BF27100 |
| Деталь: | SPONGE HOLDER IMAGE |
| Парткод: | 2BG09280 |
| Деталь: | SENSOR,TONER EMPTY B |
| Парткод: | 2BG27020 |
| Деталь: | RAIL FUSER R |
| Парткод: | 2BG02230 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BG02240 |
| Деталь: | PIN HOOK |
| Парткод: | 2BG02400 |
| Деталь: | PIN PULLEY |
| Парткод: | 2BG20350 |
| Деталь: | SHEET RM |
| Парткод: | 2BG02780 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE,BYPASS JUNCTION |
| Парткод: | 2BG27611 |
| Деталь: | SWITCH,INTERLOCK |
| Парткод: | 2AV27370 |
| Деталь: | SENSOR 12,SEPARATION |
| Парткод: | 3B827040 |
| Деталь: | COVER SCREW |
| Парткод: | 2BG04560 |
| Деталь: | SEAL PLATE LPH A |
| Парткод: | 2BG02810 |
| Деталь: | SEAL PLATE LPH B |
| Парткод: | 2BG02820 |
| Деталь: | TRAY OP |
| Парткод: | 2BG60010 |
| Деталь: | BKT OP TRAY F |
| Парткод: | 2BG60020 |
| Деталь: | BKT OP TRAY R |
| Парткод: | 2BG60100 |
| Деталь: | IC,DIMM MEMORY1 |
| Парткод: | 2A727740 |
| Деталь: | IC DIMM-128M |
| Парткод: | 2BF27050 |
| Деталь: | 168PIN DIMM 64M |
| Парткод: | 2BF60040 |
| Деталь: | HEATER,DEHUMIDIFIER(120) |
| Парткод: | 2BG28740 |
| Деталь: | HEATER,DEHUMIDIFIER(230) |
| Парткод: | 2BG28750 |
| Деталь: | MOTOR B,LIFT CASSETTE |
| Парткод: | 2BC27120 |
| Деталь: | FUSER DRIVE ASSY |
| Парткод: | 2BG00550 |
| Деталь: | PLATE DRIVE FUSER |
| Парткод: | 2BG22100 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | SPRING JOINT F |
| Парткод: | 2BG22190 |
| Деталь: | GEAR Z120H-Z34P |
| Парткод: | 2BG22490 |
| Деталь: | GEAR Z37H |
| Парткод: | 2BG22460 |
| Деталь: | BELT DU |
| Парткод: | 2BG22480 |
| Деталь: | GEAR Z60H |
| Парткод: | 2BG22070 |
| Деталь: | GEAR Z97H-Z35S |
| Парткод: | 2BG22180 |
| Деталь: | GEAR Z34S-Z33H |
| Парткод: | 2BG22120 |
| Деталь: | GEAR Z28S-Z20H |
| Парткод: | 2BG22160 |
| Деталь: | GEAR Z56H-Z50S |
| Парткод: | 2BG22110 |
| Деталь: | GEAR Z22S EJ |
| Парткод: | 2BG22700 |
| Деталь: | GEAR Z35S EJ |
| Парткод: | 2BG22130 |
| Деталь: | SHAFT FUSER CLUTCH |
| Парткод: | 2BG22560 |
| Деталь: | GEAR,DEVELOPING SPIRAL |
| Парткод: | 68314090 |
| Деталь: | GEAR Z46H |
| Парткод: | 2BG22150 |
| Деталь: | GEAR Z26S |
| Парткод: | 2BG22140 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | SWITCH,INTERLOCK |
| Парткод: | 2AV27370 |
| Деталь: | WIRE,FUSER MOTOR |
| Парткод: | 2BG27290 |
| Деталь: | HOLDER GEAR |
| Парткод: | 2BG22090 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | CLUTCH FUSER |
| Парткод: | 2BG22650 |
| Деталь: | PLATE CLUTCH FUSER |
| Парткод: | 2BG22910 |
| Деталь: | MOTOR,FIXING |
| Парткод: | 2BG27140 |
| Деталь: | MINIATURE CLAMP,UAMS-07-0 |
| Парткод: | M2105730 |
| Деталь: | MINIATURE CLAMP.UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | LOCKING WIRE SADDLE,LWS-4NS |
| Парткод: | 49828500 |
| Деталь: | WIRE,MC PCB |
| Парткод: | 2BG27310 |
| Деталь: | PLATE DRIVE DU |
| Парткод: | 2BG22440 |
| Деталь: | SHAFT DU |
| Парткод: | 2BG22450 |
| Деталь: | GEAR Z45S-Z28S |
| Парткод: | 2BG22510 |
| Деталь: | GEAR Z36P-Z34S |
| Парткод: | 2BG22500 |
| Деталь: | GEAR Z33S DU |
| Парткод: | 2BG22710 |
| Деталь: | GEAR Z38S DU |
| Парткод: | 2BG22470 |
| Деталь: | GEAR Z29 EXIT |
| Парткод: | 2BG21420 |
| Деталь: | WIRE,LPH PCB |
| Парткод: | 2BF27090 |
| Деталь: | DUCT COOLING |
| Парткод: | 2BG23010 |
| Деталь: | MCH HV PWB |
| Парткод: | 2BG28060 |
| Деталь: | STAY DUCT |
| Парткод: | 2BG26300 |
| Деталь: | DUCT MCH |
| Парткод: | 2BG10150 |
| Деталь: | EDGING,EDS-2323U (KITAGAWA) |
| Парткод: | M2104270 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | DUCT COOLING FAN |
| Парткод: | 2BG23020 |
| Деталь: | FAN 92X25-300 |
| Парткод: | 2BG27550 |
| Деталь: | FAN 80X25-100 |
| Парткод: | 2BG27790 |
| Деталь: | BRACKET FAN |
| Парткод: | 2BG10140 |
| Деталь: | SEAL DUCT MCH |
| Парткод: | 2BG10170 |
| Деталь: | ASSY.PCB ENVIRONMENT SENSOR |
| Парткод: | 2BG01200 |
| Деталь: | WIRE,MC HIGH VOLTAGE M |
| Парткод: | 2BG27920 |
| Деталь: | WIRE,MC HIGH VOLTAGE C |
| Парткод: | 2BG28660 |
| Деталь: | WIRE,MC HIGH VOLTAGE Y |
| Парткод: | 2BG28670 |
| Деталь: | WIRE,MC HIGH VOLTAGE K |
| Парткод: | 2BG28680 |
| Деталь: | STAY FUSER |
| Парткод: | 2BG02260 |
| Деталь: | SPRING HOOK |
| Парткод: | 2BG20800 |
| Деталь: | SLIDER FUSER F |
| Парткод: | 2BG02270 |
| Деталь: | PULLEY SLIDER |
| Парткод: | 2BG20340 |
| Деталь: | PIN PULLEY |
| Парткод: | 2BG20350 |
| Деталь: | SLIDER FUSER R |
| Парткод: | 2BG02280 |
| Деталь: | HOOK FUSER LOCK |
| Парткод: | 2BG20750 |
| Деталь: | PARTS,FK-810(U) |
| Парткод: | 2BF93020 |
| Деталь: | PARTS,FK-810(E) |
| Парткод: | 2BF93030 |
| Деталь: | LABEL CAUTION FUSER |
| Парткод: | 2BG05010 |
| Деталь: | FRAME ROLLER LOW |
| Парткод: | 2BG20060 |
| Деталь: | THERMOSTAT 150 |
| Парткод: | 2BG20910 |
| Деталь: | PIN PRESSURE |
| Парткод: | 2BG20120 |
| Деталь: | SPRING PRESS FUSER |
| Парткод: | 2BG20130 |
| Деталь: | MOUNT THERMISTOR LOW |
| Парткод: | 2BG20870 |
| Деталь: | THERMISTOR UP |
| Парткод: | 2BG20580 |
| Деталь: | ROLLER HEAT LOW |
| Парткод: | 2BG20020 |
| Деталь: | STOPPER FUSER B |
| Парткод: | 2BG20900 |
| Деталь: | BUSH HEAT ROLLER |
| Парткод: | 2CK20040 |
| Деталь: | BEARING FUSER |
| Парткод: | 2BG20150 |
| Деталь: | FRAME FUSER |
| Парткод: | 2BG20030 |
| Деталь: | WIRE,FUSER UNIT |
| Парткод: | 2BF27071 |
| Деталь: | HOLDER DRAWER |
| Парткод: | 2BG20360 |
| Деталь: | SHEET HARNESS A |
| Парткод: | 2BG20840 |
| Деталь: | ROLLER HEAT UP |
| Парткод: | 2BG20010 |
| Деталь: | GEAR FUSER Z38S |
| Парткод: | 2BG20140 |
| Деталь: | STOPPER FUSER |
| Парткод: | 2BG20880 |
| Деталь: | FRAME FUSER UP |
| Парткод: | 2BG20040 |
| Деталь: | THERMOSTAT 140 |
| Парткод: | 2BG20920 |
| Деталь: | GUIDE ENTRANCE UP |
| Парткод: | 2BG20080 |
| Деталь: | HOLDER HEATER R |
| Парткод: | 2BG20480 |
| Деталь: | PLATE FUSER HEATER |
| Парткод: | 2BG20590 |
| Деталь: | HOLDER HEATER F |
| Парткод: | 2BG20470 |
| Деталь: | PCB FIXING ASSY |
| Парткод: | 2BG01170 |
| Деталь: | LAMP HEATER UP 120 |
| Парткод: | 2BG20430 |
| Деталь: | LAMP HEATER UP 240 |
| Парткод: | 2BG20450 |
| Деталь: | LAMP HEATER LOW 120 |
| Парткод: | 2BG20440 |
| Деталь: | LAMP HEATER LOW 240 |
| Парткод: | 2BG20460 |
| Деталь: | SHEET HARNESSC |
| Парткод: | 2BG20860 |
| Деталь: | GUIDE ENTRANCE |
| Парткод: | 2BG20070 |
| Деталь: | GUIDE ENTRANCE LOW |
| Парткод: | 2BG20090 |
| Деталь: | COVER FUSER UP |
| Парткод: | 2BG20550 |
| Деталь: | GUIDE EXIT UP |
| Парткод: | 2BG20210 |
| Деталь: | SPRING FUSER EXIT |
| Парткод: | 2BG20890 |
| Деталь: | SHAFT EXIT |
| Парткод: | 2BG20330 |
| Деталь: | PULLY EXIT |
| Парткод: | 2BG20320 |
| Деталь: | STAY FUSER UP |
| Парткод: | 2BG20190 |
| Деталь: | COVER FUSER EXIT |
| Парткод: | 2BG20180 |
| Деталь: | SHAFT EXIT RELEASE |
| Парткод: | 2BG20290 |
| Деталь: | HOOK EXIT RELEASE |
| Парткод: | 2BG20600 |
| Деталь: | SPRING EXIT RELEASE |
| Парткод: | 2BG20310 |
| Деталь: | ROLLER FUSER EXIT |
| Парткод: | 2BG20270 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | BUSH 6 EW |
| Парткод: | 2BG22970 |
| Деталь: | GEAR Z17S EXIT |
| Парткод: | 2BG20510 |
| Деталь: | GUIDE EXIT LOW |
| Парткод: | 2BG20220 |
| Деталь: | TERMINAL EXIT ROLLER |
| Парткод: | 2BG20610 |
| Деталь: | COVER FUSER F |
| Парткод: | 2BG20560 |
| Деталь: | GEAR Z23S IDLE |
| Парткод: | 2BG20530 |
| Деталь: | COVER FUSER R |
| Парткод: | 2BG20570 |
| Деталь: | HANDLE FUSER |
| Парткод: | 2BG20540 |
| Деталь: | PIN HOOK |
| Парткод: | 2BG02400 |
| Деталь: | PRIMARY FEED ASSY |
| Парткод: | 2BG00130 |
| Деталь: | SHAFT FEED UP |
| Парткод: | 2BG06780 |
| Деталь: | UPPER GEAR,PAPER FEED |
| Парткод: | 2BC06790 |
| Деталь: | PULLEY.PAPER FEED |
| Парткод: | 2BC06900 |
| Деталь: | BUSHING.BYPASS SHAFT |
| Парткод: | 60907880 |
| Деталь: | UPPER HOUSING.PAPER FEED |
| Парткод: | 2BC06010 |
| Деталь: | BUSHING,PAPER FEED |
| Парткод: | 36706310 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | PLATE FEED F |
| Парткод: | 2BG06360 |
| Деталь: | LOWER HOUSING.PAPER FEED |
| Парткод: | 2BC06021 |
| Деталь: | LOWER REINFORCEMENT,HOUSING PAPER FEED |
| Парткод: | 2BC06360 |
| Деталь: | VIBRATION INSULATOR,RELEASE LEVER |
| Парткод: | 33906211 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 2BG06990 |
| Деталь: | TORQUE LIMITER 360 |
| Парткод: | 2BG06380 |
| Деталь: | LOWER PULLEY,PAPER FEED |
| Парткод: | 33906060 |
| Деталь: | LOWER LEVER,PAPER FEED PULLEY RELEASE |
| Парткод: | 33906090 |
| Деталь: | BUSHING,6 |
| Парткод: | 63806290 |
| Деталь: | LOWER SPRING B,PAPER FEED |
| Парткод: | 3CY06020 |
| Деталь: | PLATE FEED R |
| Парткод: | 2BG06370 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | LOWER BUSHING,PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | STOPPER 5,RING |
| Парткод: | 2BC06990 |
| Деталь: | COVER DRIVE FEED |
| Парткод: | 2BG06980 |
| Деталь: | GEAR FEED Z33S |
| Парткод: | 2BG06790 |
| Деталь: | GUIDE,CONFLUENCE |
| Парткод: | 2BC06460 |
| Деталь: | SHAFT,LEADING FEED PULLEY |
| Парткод: | 33906080 |
| Деталь: | WIRE,PAPER FEED UNIT |
| Парткод: | 2BG27270 |
| Деталь: | SWITCH PI |
| Парткод: | 2BL27450 |
| Деталь: | ACTUATOR,PAPER EMPTY |
| Парткод: | 2BC06380 |
| Деталь: | SUPPORT PLATE,LEADING FEED PULLEY |
| Парткод: | 2BC06300 |
| Деталь: | WEIGHT,LEADING FEED PULLEY |
| Парткод: | 33906180 |
| Деталь: | GEAR 18,RETARD |
| Парткод: | 34922220 |
| Деталь: | STOP RING,4 |
| Парткод: | 63511220 |
| Деталь: | PULLEY,LEADING FEED |
| Парткод: | 2BC06810 |
| Деталь: | SET AK-640B(120)(OPTION) |
| Парткод: | 3B882080 |
| Деталь: | SET AK-640B(230)(OPTION) |
| Парткод: | 3B882090 |
| Деталь: | POWER CORD(120) |
| Парткод: | 19527400 |
| Деталь: | FILM,CONVEYING |
| Парткод: | 3B860560 |
| Деталь: | REAR RETAINER,SLIDER |
| Парткод: | 3B803510 |
| Деталь: | MOUNT,SLIDER |
| Парткод: | 3B803520 |
| Деталь: | JUNCTION PLATE,SLIDER |
| Парткод: | 3B803530 |
| Деталь: | JUNCTION PLATE,MACHINE |
| Парткод: | 3B803540 |
| Деталь: | MOUNT,MACHINE |
| Парткод: | 3B803550 |
| Деталь: | STOPPER,JUNCTION PLATE |
| Парткод: | 3B803560 |
| Деталь: | RAIL,RELEASE |
| Парткод: | 3B803570 |
| Деталь: | GROUND PLATE A,NOISE |
| Парткод: | 18526211 |
| Деталь: | FRONT RETAINER,SLIDER |
| Парткод: | 3B803500 |
| Деталь: | SLIDER,FINISHER |
| Парткод: | 3B803600 |
| Деталь: | HANDLE,RELEASE |
| Парткод: | 3B803610 |
| Деталь: | RETAINER M,RELEASE |
| Парткод: | 3B860510 |
| Деталь: | HOOK M,RELEASE |
| Парткод: | 3B860520 |
| Деталь: | GROUND PLATE,FIXING UNIT |
| Парткод: | 34920190 |
| Деталь: | ACTUATOR PLATE M,SAFETY SWITCH |
| Парткод: | 3B860530 |
| Деталь: | RAIL M,RELEASE |
| Парткод: | 3B860540 |
| Деталь: | JUNCTION PLATE M,RAIL |
| Парткод: | 3B860550 |
| Деталь: | OPTION BOX ASSY(120) |
| Парткод: | 2BG60080 |
| Деталь: | OPTION BOX ASSY(200) |
| Парткод: | 2BG60090 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | 49513902 |
| Деталь: | SPACER,MAIN PCB |
| Парткод: | 2A626300 |
| Деталь: | FAN,COOLING50 |
| Парткод: | 2BG27490 |
| Деталь: | OPTION POWER SUPPLY ASSY(100) |
| Парткод: | 2BG60031 |
| Деталь: | OPTION POWER SUPPLY ASSY(200) |
| Парткод: | 2BG60041 |
| Деталь: | WIRE,OPTION POWER SUPPLY |
| Парткод: | 2BG60050 |
| Деталь: | MOUNT OPTION POWER SOURCE |
| Парткод: | 2BG60060 |
| Деталь: | INLET ASSY |
| Парткод: | 2BG60200 |
| Деталь: | CORE,9-20X32 |
| Парткод: | 65027480 |
| Деталь: | MOUNT BASE M,BASE |
| Парткод: | 3B860610 |
| Деталь: | FRAME M,BASE |
| Парткод: | 3B860620 |
| Деталь: | LEFT STAY M,BASE |
| Парткод: | 3B860630 |
| Деталь: | RIGHT STAY M,BASE |
| Парткод: | 3B860640 |
| Деталь: | FRONT GUIDE M,BASE |
| Парткод: | 3B860650 |
| Деталь: | REAR GUIDE M,BASE |
| Парткод: | 3B860660 |
| Деталь: | SHAFT M,BASE |
| Парткод: | 3B860670 |
| Деталь: | PULLEY.FINISHER |
| Парткод: | 3AK02080 |
| Деталь: | PIN,FEED FULCRUM |
| Парткод: | 77706670 |
| Деталь: | LEFT COVER M,BASE |
| Парткод: | 3B860680 |
| Деталь: | RIGHT COVER M,BASE |
| Парткод: | 3B860690 |
| Деталь: | WIRE,FINISHER JUNCTION |
| Парткод: | 2BG60240 |
| Деталь: | BINDING TAP-TIGHT S SCREW M4X14 |
| Парткод: | B3024140 |
| Деталь: | TP TAP-TITE P SCREW(CHROMIUM) |
| Парткод: | B4144080 |
| Деталь: | TP TAP-TITE S SCREW M4X20(TRIVALENT CHROMATING) |
| Парткод: | BAB54200 |
| Деталь: | TRIPLE SCREW M3X5 (BLACK) |
| Парткод: | B4303050 |
| Деталь: | BIND TAP-TITE S SCREW M4X08 |
| Парткод: | B1A54080 |
| Деталь: | BINDING SCREW BVM4X6 (BLACK) |
| Парткод: | B1304060 |
| Деталь: | TRIPLE SCREW M4X6(CHROMIUM) |
| Парткод: | B4104060 |
| Деталь: | BINDING SCREW BVM3X5 (BLACK) |
| Парткод: | B1303050 |
| Деталь: | BINDING SCREW CVM3X5 |
| Парткод: | B1003050 |
| Деталь: | BIND SCREW M4X06(TRIVALENT CHROMATING) |
| Парткод: | B1B04060 |
| Деталь: | BINDING SCREW CVM4X10 |
| Парткод: | B1004100 |
| Деталь: | STOP RING (E-9) |
| Парткод: | D1000900 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | OPERATION E ASSY |
| Парткод: | 2BF00020 |
| Деталь: | OPERATION I ASSY I |
| Парткод: | 2BF00030 |
| Деталь: | OPERATION F ASSY F |
| Парткод: | 2BF00040 |
| Деталь: | KEY START |
| Парткод: | 2BF04040 |
| Деталь: | KEY CANCEL |
| Парткод: | 2BF04050 |
| Деталь: | BUTTON |
| Парткод: | 2BF04060 |
| Деталь: | COVER OPERATION |
| Парткод: | 2BF04010 |
| Деталь: | COVER OPERATION I |
| Парткод: | 2BF04110 |
| Деталь: | COVER OPERATION F |
| Парткод: | 2BF04120 |
| Деталь: | PANEL OPERATION |
| Парткод: | 2BF04020 |
| Деталь: | OPERATION PCB ASSY |
| Парткод: | 2BF01050 |
| Деталь: | CORE10-20X10 |
| Парткод: | 2A627940 |
| Деталь: | PARTS,DK-810 |
| Парткод: | 2BF93112 |
| Деталь: | PARTS,MCH UNIT,SP |
| Парткод: | 2BG93210 |
| Деталь: | TP TAP-TITE P SCREW M3X08 |
| Парткод: | BAA63080 |
| Деталь: | PLATE DRUM F |
| Парткод: | 2BG08100 |
| Деталь: | JOINT DRIVE DLP |
| Парткод: | 2BG14160 |
| Деталь: | SPRING DS F |
| Парткод: | 2BG14410 |
| Деталь: | SPRING DS R |
| Парткод: | 2BG14420 |
| Деталь: | PARTS,DV-810Y(U) |
| Парткод: | 2BG93121 |
| Деталь: | PARTS, DV-810Y(J/E) |
| Парткод: | 2BG93111 |
| Деталь: | PARTS,DV-810M(U) |
| Парткод: | 2BG93141 |
| Деталь: | PARTS,DV-810M(J/E) |
| Парткод: | 2BG93131 |
| Деталь: | PARTS,DV-810C(U) |
| Парткод: | 2BG93161 |
| Деталь: | PARTS,DV-810C(J/E) |
| Парткод: | 2BG93151 |
| Деталь: | PARTS,DV-810K(U) |
| Парткод: | 2BG93180 |
| Деталь: | PARTS, DV-810K(J/E) |
| Парткод: | 2BG93170 |
| Деталь: | DB HV PWB |
| Парткод: | 2BG28261 |
| Деталь: | SPACER,KGPS-10S |
| Парткод: | M2108290 |
| Деталь: | LOCKING WIRE SADDLE,LWS-2NS |
| Парткод: | 49427223 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE,DU SWITCH JUNCTION |
| Парткод: | 2BG27340 |
| Деталь: | WIRE,DB PCB |
| Парткод: | 2BG27170 |
| Деталь: | CONTROLLER ASSY SP |
| Парткод: | 2BF68040 |
| Деталь: | CONTROLLER ASSY US SP |
| Парткод: | 2BF68070 |
| Деталь: | DIMM ASSY |
| Парткод: | 2BF01040 |
| Деталь: | FAN 80X15-60 |
| Парткод: | 2BF27020 |
| Деталь: | IC DIMM-128M |
| Парткод: | 2BF27050 |
| Деталь: | PRINTER CONTROL PCB |
| Парткод: | 2BF28010 |
| Деталь: | PLATE,OPTION |
| Парткод: | 3BH26020 |
| Деталь: | PIN,OPTION |
| Парткод: | 3BH26030 |
| Деталь: | PLATE MAIN |
| Парткод: | 2BG26031 |
| Деталь: | RAIL OPTION A |
| Парткод: | 2BL26210 |
| Деталь: | RAIL OPTION B |
| Парткод: | 2BL26220 |
| Деталь: | GUIDE CF CARD |
| Парткод: | 2BM26020 |
| Деталь: | RECEPTACLE EL 2P.ELR-02V |
| Парткод: | 41529100 |
| Деталь: | BOX CONTROLLER |
| Парткод: | 2BG26010 |
| Деталь: | BINDING BAND,KB-100-1 |
| Парткод: | 49826601 |
| Деталь: | PLATE SHIELD |
| Парткод: | 2BG26310 |
| Деталь: | FERRITE CORE,SFT-59SN(TAKEUCHI) |
| Парткод: | M70C0010 |
| Деталь: | CORE 10-20X10 |
| Парткод: | 2A627940 |
| Деталь: | PLATE EARTH CONT BOX |
| Парткод: | 2BG02760 |
| Деталь: | FAN 80X25-120 |
| Парткод: | 2BG27890 |
| Деталь: | EDGING.EDS-1717U |
| Парткод: | M2104220 |
| Деталь: | EDGING,EDS-2323U(KITAGAWA) |
| Парткод: | M2104270 |
| Деталь: | WIRE SADDLE,WS-2WS |
| Парткод: | 49829401 |
| Деталь: | POWER SUPPLY ASSY(100) |
| Парткод: | 2BF01022 |
| Деталь: | POWER SUPPLY ASSY(200) |
| Парткод: | 2BF01032 |
| Деталь: | POWER INLET ASSY |
| Парткод: | 2BG01070 |
| Деталь: | SHIELD BOX |
| Парткод: | 2BG26020 |
| Деталь: | POWER CORD(120) |
| Парткод: | 19527400 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | POWER CODE AS(240) |
| Парткод: | 29927231 |
| Деталь: | PLUG EL 2P.ELP-02V |
| Парткод: | 41529101 |
| Деталь: | SPACER PILOT PIN |
| Парткод: | 2BG09360 |
| Деталь: | PLATE PILOT PIN |
| Парткод: | 2BG09120 |
| Деталь: | HANDLE |
| Парткод: | 2BG02180 |
| Деталь: | CAP HANDLE |
| Парткод: | 2BG02470 |
| Деталь: | CAP HANDLE R |
| Парткод: | 2BG02480 |
| Деталь: | GUIDE TC F |
| Парткод: | 2BG02600 |
| Деталь: | PULLEY RAIL B |
| Парткод: | 2BG02770 |
| Деталь: | LEVER LOCK TC F |
| Парткод: | 2BG02620 |
| Деталь: | PIN LOCK TC |
| Парткод: | 2BG02650 |
| Деталь: | SPRING COVER R |
| Парткод: | 3B706550 |
| Деталь: | LOCK COVER R |
| Парткод: | 2BL06490 |
| Деталь: | HUM SENSOR F |
| Парткод: | 2BG28250 |
| Деталь: | WIRE,F HUM SENSOR |
| Парткод: | 2BG28800 |
| Деталь: | HOLDER HV DLP |
| Парткод: | 2BG09130 |
| Деталь: | SPRING HV DLP |
| Парткод: | 2BG09160 |
| Деталь: | PLATE HV DLP A |
| Парткод: | 2BG09140 |
| Деталь: | SENSOR WASTE |
| Парткод: | 2BG18520 |
| Деталь: | WIRE,WASTE SENSOR |
| Парткод: | 2BG27200 |
| Деталь: | WIRE,DB HIGH VOLTAGE |
| Парткод: | 2BG27850 |
| Деталь: | SPRING LOCK TC |
| Парткод: | 2BG02640 |
| Деталь: | PIN HOOK |
| Парткод: | 2BG02400 |
| Деталь: | SPRING EARTH RAIL |
| Парткод: | 2BG06710 |
| Деталь: | STOPPER FEED UNIT |
| Парткод: | 2BG06970 |
| Деталь: | MINIATURE CLAMP,UAMS-07-0 |
| Парткод: | M2105730 |
| Деталь: | SLIDER,DECK |
| Парткод: | 2BC07680 |
| Деталь: | PLATE RAIL R |
| Парткод: | 2BG02060 |
| Деталь: | RAIL CASSETTE R |
| Парткод: | 2BG06900 |
| Деталь: | WIRE,HERTER |
| Парткод: | 2BG27780 |
| Деталь: | HOOK CASSETTE |
| Парткод: | 2BG06420 |
| Деталь: | SPRING CASS HOOK |
| Парткод: | 2BG06720 |
| Деталь: | PLATE RAIL L |
| Парткод: | 2BG02070 |
| Деталь: | RAIL CASSETTE L |
| Парткод: | 2BG06910 |
| Деталь: | SHEET HARNESSTC |
| Парткод: | 2BG02500 |
| Деталь: | RAIL CASSETTE C |
| Парткод: | 2BG06430 |
| Деталь: | SPRING A |
| Парткод: | 2BG02720 |
| Деталь: | RAIL FUSER F |
| Парткод: | 2BG02220 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BG02240 |
| Деталь: | PIN PULLEY |
| Парткод: | 2BG20350 |
| Деталь: | PLATE MIDDLE L |
| Парткод: | 2BG02460 |
| Деталь: | STAY MIDDLE |
| Парткод: | 2BG02450 |
| Деталь: | WIRE,T UNIT JUNCTION A |
| Парткод: | 2BG28500 |
| Деталь: | WIRE,T UNIT JUNCTION B |
| Парткод: | 2BG28700 |
| Деталь: | SCREW A |
| Парткод: | 2BG02410 |
| Деталь: | WIRE,FUSER JUNCTION |
| Парткод: | 2BG27540 |
| Деталь: | WASTE TONER ASSY |
| Парткод: | 2BG00330 |
| Деталь: | TRAY WASTE |
| Парткод: | 2BG18320 |
| Деталь: | JOINT WASTE |
| Парткод: | 2BG18470 |
| Деталь: | BRACKET TB DRIVE |
| Парткод: | 2BG18480 |
| Деталь: | WORM WHEEL Z34S-Z15H |
| Парткод: | 2BG18490 |
| Деталь: | WIRE,TONER BOTTLE CHECK |
| Парткод: | 2BG27940 |
| Деталь: | WIRE,MOTOR BOTTLE |
| Парткод: | 2BG28650 |
| Деталь: | GEAR WORM |
| Парткод: | 2BM14540 |
| Деталь: | DC motor |
| Парткод: | 2BM27340 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | WASTE TONER BOX ASSY |
| Парткод: | 2BG00342 |
| Деталь: | COVER RIGHT F |
| Парткод: | 2BG04050 |
| Деталь: | COVER RIGHT R |
| Парткод: | 2BG04060 |
| Деталь: | COVER REAR |
| Парткод: | 2BG04120 |
| Деталь: | MAGNET CATCH |
| Парткод: | 60804120 |
| Деталь: | COVER INNER LEFT |
| Парткод: | 2BG04150 |
| Деталь: | LEVER LOCK WASTE |
| Парткод: | 2BG04160 |
| Деталь: | SPRING LOCK WASTE |
| Парткод: | 2BG04170 |
| Деталь: | COVER INNER RIGHT |
| Парткод: | 2BG04140 |
| Деталь: | LABEL OPERATION FRONT |
| Парткод: | 2BG05040 |
| Деталь: | FRONT MAGNET,COVER |
| Парткод: | 2BC04530 |
| Деталь: | COVER INNER MIDDLE |
| Парткод: | 2BG04130 |
| Деталь: | LEVER LOCK CONTAINER |
| Парткод: | 2BG09201 |
| Деталь: | SPRING LOCK CONT |
| Парткод: | 2BG09210 |
| Деталь: | STOPPER IMAGE |
| Парткод: | 2BG09220 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | FRONT COVER ASSY F |
| Парткод: | 2BF00170 |
| Деталь: | COVER FRONT F |
| Парткод: | 2BF04210 |
| Деталь: | COVER FRONT R |
| Парткод: | 2BG04020 |
| Деталь: | BAND A |
| Парткод: | 2BG04310 |
| Деталь: | PLATE MAGCHATCH |
| Парткод: | 2BM04100 |
| Деталь: | COVER CASSETTE R |
| Парткод: | 2BG04100 |
| Деталь: | COVER LEFT |
| Парткод: | 2BG04070 |
| Деталь: | RIGHT COVER ASSY |
| Парткод: | 2BG00100 |
| Деталь: | SHAFT FEED B |
| Парткод: | 2BG06150 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BG06161 |
| Деталь: | COVER FEED R |
| Парткод: | 2BG06200 |
| Деталь: | BAND B |
| Парткод: | 2BG06480 |
| Деталь: | SPRING FEED B |
| Парткод: | 2BG06650 |
| Деталь: | LABEL LEFT COVER A |
| Парткод: | 2BL05250 |
| Деталь: | COVER CASSETTE L |
| Парткод: | 2BG04110 |
| Деталь: | SPRING COVER |
| Парткод: | 2BG04330 |
| Деталь: | PLATE HOLDER IMAGE |
| Парткод: | 2BG09010 |
| Деталь: | WASTE SHUTTER UNIT |
| Парткод: | 2BG68120 |
| Деталь: | OZON FILTER |
| Парткод: | 2BG23030 |
| Деталь: | SHEET FF |
| Парткод: | 2BG02790 |
| Деталь: | CAP TOP FRONT |
| Парткод: | 2BG04360 |
| Деталь: | CAP TOP REAR |
| Парткод: | 2BG04370 |
| Деталь: | SEAL COLOR SYMBOL |
| Парткод: | 2BG05080 |
| Деталь: | HOLDER IMAGE F |
| Парткод: | 2BG09030 |
| Деталь: | PLATE HV DLP B |
| Парткод: | 2BG09060 |
| Деталь: | PLATE EARTH DRUM |
| Парткод: | 2BG09090 |
| Деталь: | PLATE RETAINER IMAGE |
| Парткод: | 2BG09050 |
| Деталь: | LEVER LOCK IMAGE |
| Парткод: | 2BG09250 |
| Деталь: | SCREW C |
| Парткод: | 2BG09260 |
| Деталь: | COVER INNER LOW |
| Парткод: | 2BG09170 |
| Деталь: | LEVER LOCK MCH |
| Парткод: | 2BG09180 |
| Деталь: | SPRING LOCK MCH |
| Парткод: | 2BG09190 |
| Деталь: | SEAL COVER INNER LOW M |
| Парткод: | 2BG09270 |
| Деталь: | SEAL COVER INNER LOW C |
| Парткод: | 2BG09330 |
| Деталь: | SEAL COVER INNER LOW Y |
| Парткод: | 2BG09340 |
| Деталь: | SEAL COVER INNER LOW K |
| Парткод: | 2BG09350 |
| Деталь: | LUTCH |
| Парткод: | 2BM02460 |
| Деталь: | COVER CONTAINER K |
| Парткод: | 2BG09320 |
| Деталь: | COVER CONTAINER Y |
| Парткод: | 2BG09310 |
| Деталь: | COVER CONTAINER C |
| Парткод: | 2BG09300 |
| Деталь: | COVER CONTAINER M |
| Парткод: | 2BG09290 |
| Деталь: | LABEL OPERATION RIGHT |
| Парткод: | 2BG05050 |
| Деталь: | COVER LPH PCB |
| Парткод: | 2BG26050 |
| Деталь: | TOP COVER ASSY |
| Парткод: | 2BG00060 |
| Деталь: | COVER TOP |
| Парткод: | 2BG04030 |
| Деталь: | STOPPER PAPER |
| Парткод: | 2BG04300 |
| Деталь: | COVER TOP R |
| Парткод: | 2BG04040 |
| Деталь: | COVER TOP L |
| Парткод: | 2BG04090 |
| Деталь: | FILTER ASSY |
| Парткод: | 2BG00091 |
| Деталь: | COVER DUCT |
| Парткод: | 2BG04270 |
| Деталь: | COVER SW |
| Парткод: | 2BG04520 |
| Деталь: | SHEETSW |
| Парткод: | 2BG04530 |
| Деталь: | TAPE SW |
| Парткод: | 2BG04540 |
| Деталь: | PLATE FEED L |
| Парткод: | 2BG06250 |
| Деталь: | MINIATURE CLAMP.UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | ROLLER FEED B |
| Парткод: | 2BG06240 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | BUSH 8 EW |
| Парткод: | 2BG22950 |
| Деталь: | SPONGE WIRE A |
| Парткод: | 2BG06500 |
| Деталь: | SWITCH,CONVEYING |
| Парткод: | 2BC27010 |
| Деталь: | WIRE,PAPER FEED JUNCTION |
| Парткод: | 2BG27320 |
| Деталь: | EDGING.EDS-2 |
| Парткод: | M2104210 |
| Деталь: | FEED UNIT ASSY |
| Парткод: | 2BF00092 |
| Деталь: | PLATE FEED LOW |
| Парткод: | 2BG06630 |
| Деталь: | LEVER FEED LOCK |
| Парткод: | 2BG06920 |
| Деталь: | FRAME FEED |
| Парткод: | 2BG06010 |
| Деталь: | WIRE,REGISTRATION SWITCH |
| Парткод: | 2BG27571 |
| Деталь: | SWITCH,PHOT0 interruptor |
| Парткод: | 2A127050 |
| Деталь: | ACTUATOR FEED |
| Парткод: | 2BG06870 |
| Деталь: | SPRING ACT FEED |
| Парткод: | 2BG06450 |
| Деталь: | SPRING ACT REG |
| Парткод: | 2BG06460 |
| Деталь: | SPRING EARTH FEED |
| Парткод: | 2BG06690 |
| Деталь: | LEVER FEED B |
| Парткод: | 2BG06110 |
| Деталь: | HOLDER EARTH PIN |
| Парткод: | 2BG07540 |
| Деталь: | PIN EARTH FEED |
| Парткод: | 2BG07530 |
| Деталь: | SPRING HOLDER PIN |
| Парткод: | 2BG07550 |
| Деталь: | PLATE EARTH REGIST |
| Парткод: | 2BG06930 |
| Деталь: | HIGHMEG ASSY |
| Парткод: | 2BG06640 |
| Деталь: | ROLLER FEED A |
| Парткод: | 2BG06060 |
| Деталь: | SPONGE WIRE D |
| Парткод: | 2BG06570 |
| Деталь: | GEAR Z19S |
| Парткод: | 2BG06320 |
| Деталь: | COVER ACT FEED |
| Парткод: | 2BG07500 |
| Деталь: | SHAFT FEED UNIT |
| Парткод: | 2BG06070 |
| Деталь: | HOOK FEED F |
| Парткод: | 2BG06080 |
| Деталь: | HOOK FEED R |
| Парткод: | 2BG06740 |
| Деталь: | SPRING FEED HOOK |
| Парткод: | 2BG06950 |
| Деталь: | STOPPER TC |
| Парткод: | 2BG06270 |
| Деталь: | SPRING PRESS TC |
| Парткод: | 2BG06400 |
| Деталь: | SPRING EARTH GUIDE |
| Парткод: | 2BG06410 |
| Деталь: | PLATE GUIDE REGIST LOW |
| Парткод: | 2BG06030 |
| Деталь: | ROLLER REGIST LOW |
| Парткод: | 2BG06050 |
| Деталь: | BUSH 6 NB |
| Парткод: | 2BG07520 |
| Деталь: | SHEET REGIST |
| Парткод: | 2BG06470 |
| Деталь: | PLATE GUIDE REGIST UP |
| Парткод: | 2BG06750 |
| Деталь: | SPRING REG RELEASE |
| Парткод: | 2BG06490 |
| Деталь: | ROLLER REGIST UP |
| Парткод: | 2BG06040 |
| Деталь: | BUSH REGIST UP NB |
| Парткод: | 2BG07510 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | SPRING REGIST A |
| Парткод: | 2BG06340 |
| Деталь: | SPRING REGIST B |
| Парткод: | 2BG07600 |
| Деталь: | GEAR Z15S |
| Парткод: | 2BG06330 |
| Деталь: | GEAR Z18S-Z22S |
| Парткод: | 2BG06170 |
| Деталь: | HOLDER FEED DRIVE |
| Парткод: | 2BG06100 |
| Деталь: | GEAR Z19S-Z26S |
| Парткод: | 2BG06180 |
| Деталь: | GEAR Z20S-Z24S |
| Парткод: | 2BG06770 |
| Деталь: | GEAR 21 |
| Парткод: | 3A821110 |
| Деталь: | MINIATURE CLAMP,UAMS-05-2 |
| Парткод: | M2105720 |
| Деталь: | RAIL FEED R |
| Парткод: | 2BG06310 |
| Деталь: | HOLDER TC R |
| Парткод: | 2BG06730 |
| Деталь: | RAIL FEED F |
| Парткод: | 2BG06301 |
| Деталь: | HOLDER TC F |
| Парткод: | 2BG06220 |
| Деталь: | COVER FEED |
| Парткод: | 2BG06190 |
| Деталь: | GUIDE FEED LOW |
| Парткод: | 2BG06230 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BG06161 |
| Деталь: | LEVER COVER FEED |
| Парткод: | 2BG06280 |
| Деталь: | SPRING COVER FEED |
| Парткод: | 2BG06660 |
| Деталь: | SHAFT FEED C |
| Парткод: | 2BG06290 |
| Деталь: | HANDLE FEED |
| Парткод: | 2BG06350 |
| Деталь: | SPRING HANDLE FEED |
| Парткод: | 2BG06260 |
| Деталь: | LEVER FEED A |
| Парткод: | 2BG06440 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 2BG07560 |
| Деталь: | SPRING FEED A |
| Парткод: | 2BG07570 |
| Деталь: | SHAFT FEED A |
| Парткод: | 2BG06140 |
| Деталь: | CLUTCH REGIST 32 |
| Парткод: | 2BG22420 |
| Деталь: | PLATE MAIN DRIVE R |
| Парткод: | 2BG22040 |
| Деталь: | SPRING JOINT F |
| Парткод: | 2BG22190 |
| Деталь: | GEAR Z16S-Z40P |
| Парткод: | 2BG22600 |
| Деталь: | BELT CONT DRIVE |
| Парткод: | 2BG22630 |
| Деталь: | GEAR Z46H-Z20P |
| Парткод: | 2BG22590 |
| Деталь: | GEAR Z70H-Z23H |
| Парткод: | 2BG22060 |
| Деталь: | GEAR Z60H |
| Парткод: | 2BG22070 |
| Деталь: | GEAR Z38H |
| Парткод: | 2BG22540 |
| Деталь: | GEAR Z32S CONT |
| Парткод: | 2BG22610 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | COUPLING DLP DRIVE |
| Парткод: | 2BG22520 |
| Деталь: | SPRING COUPLING DLP |
| Парткод: | 2BG22530 |
| Деталь: | SHAFT DLP DRIVE |
| Парткод: | 2BG22050 |
| Деталь: | COLLAR DLP COUPLING |
| Парткод: | 2BG22860 |
| Деталь: | PLATE MAIN DRIVE F |
| Парткод: | 2BG22030 |
| Деталь: | BEARING MF128ZZ |
| Парткод: | 2BG22940 |
| Деталь: | GEAR Z20H |
| Парткод: | 2BG22080 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | BEARING.DRIVE |
| Парткод: | 2AV22410 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | MOTOR,COLOR DEVELOPING |
| Парткод: | 2BG27130 |
| Деталь: | LOCKING WIRE SADDLE,LWS-3NS |
| Парткод: | 49427224 |
| Деталь: | WIRE SADDLE,HL-28-0(KITAGAWA) |
| Парткод: | M2109310 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | HOLDER CONT DRIVE |
| Парткод: | 2BG22830 |
| Деталь: | WORM WHEEL 32-Z20S |
| Парткод: | 2BG22820 |
| Деталь: | GEAR Z28S CONT |
| Парткод: | 2BG22840 |
| Деталь: | JOINT CONT DRIVE |
| Парткод: | 2BG22800 |
| Деталь: | SP JOINT T SW D1234 |
| Парткод: | 2BM14190 |
| Деталь: | GEAR Z28S-Z20S CONT |
| Парткод: | 2BG22810 |
| Деталь: | DC motor |
| Парткод: | 2BM27340 |
| Деталь: | GEAR WORM |
| Парткод: | 2BM14540 |
| Деталь: | WIRE,MOTOR TONER |
| Парткод: | 2BG28690 |
| Деталь: | WIRE SADDLE,WS-2WS |
| Парткод: | 49829401 |
| Деталь: | GEAR Z54S |
| Парткод: | 2BG22350 |
| Деталь: | FEED DRIVE ASSY |
| Парткод: | 2BG00540 |
| Деталь: | PLATE FEED DRIVE R |
| Парткод: | 2BG22260 |
| Деталь: | HOLDER CLUTCH |
| Парткод: | 2BG22280 |
| Деталь: | CLUTCH 1 FEED H |
| Парткод: | 2BG22670 |
| Деталь: | CLUTCH 1 FEED L |
| Парткод: | 2BG22680 |
| Деталь: | SHAFT PICK-UP CL H |
| Парткод: | 2BG22390 |
| Деталь: | SHAFT PICK-UP CL L |
| Парткод: | 2BG22400 |
| Деталь: | BUSH 8 |
| Парткод: | 2BG22980 |
| Деталь: | SHAFT REGIST CLUTCH |
| Парткод: | 2BG22360 |
| Деталь: | SHAFT FEED CLUTCH H |
| Парткод: | 2BG22370 |
| Деталь: | SHAFT FEED CLUTCH L |
| Парткод: | 2BG22380 |
| Деталь: | SHAFT FEED CLUTCH B |
| Парткод: | 2BG22410 |
| Деталь: | GEAR Z111H-Z36S |
| Парткод: | 2BG22290 |
| Деталь: | CLUTCH FEED 34 |
| Парткод: | 2BG22430 |
| Деталь: | CLUTCH FEED L |
| Парткод: | 2BG22660 |
| Деталь: | GEAR 37,S.B |
| Парткод: | 45729402 |
| Деталь: | GEAR Z18S |
| Парткод: | 2BG22310 |
| Деталь: | PLATE FEED UPPER F |
| Парткод: | 2BG22250 |
| Деталь: | GEAR 20 |
| Парткод: | 34922410 |
| Деталь: | MINIATURE CLAM P, UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | CUT WASHER 6 |
| Парткод: | 2BG22930 |
| Деталь: | GEAR Z99H-Z43S |
| Парткод: | 2BG22300 |
| Деталь: | GEAR Z34S-Z31S |
| Парткод: | 2BG22320 |
| Деталь: | GEAR Z43S |
| Парткод: | 2BG22340 |
| Деталь: | GEAR Z34S-Z31S8 |
| Парткод: | 2BG22550 |
| Деталь: | GEAR 21 |
| Парткод: | 3A821110 |
| Деталь: | REAR GEAR 25,DEVELOPING |
| Парткод: | 36714140 |
| Деталь: | CLUTCH DESK FEED L |
| Парткод: | 2BG22690 |
| Деталь: | GEAR B,PF PULLEY |
| Парткод: | 45729404 |
| Деталь: | PLATE FEED LOW F |
| Парткод: | 2BG22270 |
| Деталь: | GEAR Z35S |
| Парткод: | 2BG22330 |
| Деталь: | GEAR,CENTRAL LEAD ROLLER |
| Парткод: | 72622060 |
| Деталь: | GEAR 32,TRANSFER DRIVE |
| Парткод: | 2AZ22490 |
| Деталь: | MOTOR,PAPER FEED |
| Парткод: | 2BG27160 |
| Деталь: | PCB CLUTCH JUNCTION ASSY |
| Парткод: | 2BG01140 |
| Деталь: | EDGING,EDS-0607M(KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | WIRE,PAPER FEED MOTOR |
| Парткод: | 2BG27210 |
| Деталь: | EXIT F ASSY |
| Парткод: | 2BF00102 |
| Деталь: | PLATE EXIT A |
| Парткод: | 2BG21240 |
| Деталь: | SHAFT PULLEY EXIT A |
| Парткод: | 2BG21080 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BG06161 |
| Деталь: | BUSH EXIT ROLLER |
| Парткод: | 2BG07580 |
| Деталь: | SPRING PULLEY EXIT B |
| Парткод: | 2BG21390 |
| Деталь: | HOLDER PULLEY EXIT |
| Парткод: | 2BG21770 |
| Деталь: | PULLEY EXIT FD |
| Парткод: | 2BG21170 |
| Деталь: | SPRING PULLEY FD |
| Парткод: | 2BG21970 |
| Деталь: | ROLLER EXIT A |
| Парткод: | 2BG21010 |
| Деталь: | ROLLER EXIT B |
| Парткод: | 2BG21020 |
| Деталь: | BUSH 6 EW |
| Парткод: | 2BG22970 |
| Деталь: | PULLEY 24,CONVEYING |
| Парткод: | 3A722040 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | ACTUATOR EXIT A |
| Парткод: | 2BG21280 |
| Деталь: | PLATE EXIT B |
| Парткод: | 2BG21250 |
| Деталь: | BELT,DRIVE EXIT |
| Парткод: | 2BG21180 |
| Деталь: | DISCHARGER EXIT FD |
| Парткод: | 2BG21580 |
| Деталь: | DISCHARGER EXIT MID |
| Парткод: | 2BG21590 |
| Деталь: | SHEET FD |
| Парткод: | 2BG07591 |
| Деталь: | SWITCH,PHOT0 interruptor |
| Парткод: | 2A127050 |
Коды ошибок
0121
0122
0123
0124
0150
0160
0170
0240
0310
0420
0440
0500
0700
0710
0750
0926
0951
0953
0954
1010
1100
1110
1120
1130
1140
1150
1160
1170
1200
2101
2102
2201
2202
2203
2204
2500
2600
2700
2710
5100
5301
5302
5303
5304
6000
6020
6030
6050
6100
6120
6130
6150
6400
6410
6420
7001
7002
7003
7004
7101
7102
7103
7104
7200
7210
7301
7302
7303
7304
7600
7610
7620
7800
7810
8010
8020
8030
8040
8140
8150
8170
8180
8190
8210
8220
8230
8240
8300
8310
8320
8330
F000
F010
F020
F030
F040
F050
F060
F070
Описание
| Error code: | 0121 |
| Description: | Thermistor Error (Dryer) Thermistor of the Dryer doesn`t work correctly |
| Causes: | Thermistor of the Dryer is broken. There is a cut-line/short in the wiring of the Thermistor. |
| Remedy: | 1) Check the wirings of Dryer 2) Thermistor Replacement |
| Error code: | 0122 |
| Description: | Thermistor error (Pre-heater F) The abnormalities of a thermistor for Pre-heater F |
| Causes: | The device is abnormal. The thermistor wiring has short-circuited or come down. |
| Remedy: | Checking the wiring Thermistor replacement |
| Error code: | 0123 |
| Description: | EEPROM read error (drum PWB M) • When data is transmitted to the EEPROM on drum PWB M, the ACK signal is not returned within 1 s. |
| Causes: | Poor contact in the connector terminals. Defective drum PWB M. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine controller PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective drum PWB M. Replace the magenta process unit. |
| Error code: | 0124 |
| Description: | EEPROM read error (drum PWB Y) • When data is transmitted to the EEPROM on drum PWB Y, the ACK signal is not returned within 1 s. |
| Causes: | Poor contact in the connector terminals. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC12 on the engine controller PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective drum PWB Y. Replace the black process unit. |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0240 |
| Description: | There is a problem in the Scan/Feed Motor control. |
| Causes: | The control of the Scan/Feed Motor is not done correctly. There is a cut-line in the Scan/Feed Motor control part on the Main Board. |
| Remedy: | Main Board replacement |
| Error code: | 0310 |
| Display: | LASER ERROR |
| Description: | Laser malfunction |
| Causes: | • The SOS signal is not detected within a given period of time after the output of the laser has been started. |
| Remedy: | 1 Check the cable and connector for proper connection and correct as necessary. - - 2 Change PH unit. - - 3 Change PRCB. - - |
| Error code: | 0420 |
| Description: | Paper feeder communication error Communication error between control PWB and optional paper feeder. |
| Causes: | Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF main-PWB. |
| Remedy: | Improper installation paper feeder. Follow installation instruction carefully again. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective control PWB. Replace the control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder). Defective PF main- PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 0440 |
| Description: | Communication error between printer and document finisher/ mailbox sorter • The CPU (U2) of engine controller PWB (KP-992) does not communicate with the DF-31 document finisher/SO-30 mailbox sorter normally. • The ASIC (U8) of engine controller PWB (KP-992) does not communicate to the DF-31 document finisher/SO-30 mailbox sorter normally. |
| Causes: | Defective engine controller PWB (KP-992). Defective main PWB of DF-31 document finisher/SO-30 mailbox sorter. Defective paper feeder/options relay PWB (KP-995). Defective signal cable between printer and DF-31 document finisher/ SO-30 mailbox sorter. Defective harness (2CK2719) between engine controller PWB (KP-992) and paper feeder/options relay PWB (KP- 995), or poor contact of the connector terminals. Defective document finisher interface PWB. Defective harness (2CK2727) between document finisher interface PWB and engine controller PWB (KP- 992), or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the main PWB of DF-31 document finisher/SO-30 mailbox sorter. See DF-31 document finisher/SO-30 mailbox sorter’s service manual. Replace the paper feeder/options relay PWB (KP-995). Replace the signal cable between printer and DF-31 document finisher/SO-30 mailbox sorter. Check the continuity of the harness (2CK2719). Check the insertion of connectors. Replace the document finisher interface PWB. Check the continuity of the harness (2CK2727). Check the insertion of connectors. |
| Error code: | 0500 |
| Display: | FUSER ERROR |
| Description: | Fuser warm-up failure |
| Causes: | • The thermistor /1 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started. |
| Remedy: | 1 Change fuser unit. - - 2 For C110: 1. Main switch is turned ON. 2. Open the top cover. 3. Press the following keys in this order. ROTATE TONER key -ATTENTION key - ATTENTION key - ROTATE TONER key. 4. Main switch is turned OFF/ON. For C130n: 1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. See P.103 - - 3 Change PRCB. - - 4 Change DCPU. - - |
| Error code: | 0700 |
| Description: | Paper feeder EEPROM error 1 (upper of optional paper feeder PF-640) • When power is turned on, an error is detected in memory check for the upper of the optional 500 sheets paper feeder and a backup memory error is received in serial communication data |
| Causes: | Poor contact in the connector terminals. Defective engine controller PWB. Defective upper of optional paper feeder PF-640. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine controller PWB. Repair or replace if necessary. Defective engine controller PWB. Replace the engine controller PWB. Defective upper of optional paper feeder PF-640. Replace the paper feeder PF-640 with another unit and check the operation. If the operation is normal, replace or repair the upper of the optional paper feeder PF-640. |
| Error code: | 0710 |
| Description: | Paper feeder EEPROM error 2 (lower of optional paper feeder PF-640) • When power is turned on, an error is detected in memory check for the lower of the paper feeder PF-640 and a backup memory error is received in serial communication data. |
| Causes: | Poor contact in the connector terminals. Defective engine controller PWB. Defective lower of optional paper feeder PF-640. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine controller PWB. Repair or replace if necessary. Defective engine controller PWB. Replace the engine controller PWB. Defective lower of optional paper feeder PF-640. Replace the paper feeder PF-640 with another unit and check the operation. If the operation is normal, replace or repair the lower of the optional paper feeder PF-640. |
| Error code: | 0750 |
| Description: | Document finisher EEPROM error • A backup memory error is received in serial communication data from the finisher. |
| Causes: | Poor contact in the connector terminals. Defective engine controller PWB. Defective optional document finisher. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine controller PWB. Repair or replace if necessary. Defective engine controller PWB. Replace the engine controller PWB. Defective optional document finisher. Replace the document finisher with another unit and check the operation. If the operation is normal, replace or repair the document finisher. |
| Error code: | 0926 |
| Description: | LPH current correction EEPROM error • A correction data error for the second color (cyan) is detected.. |
| Causes: | Defective EEPROM of LPH drive PWB. |
| Remedy: | Defective EEPROM of LPH drive PWB. Rewrite correction data. |
| Error code: | 0951 |
| Description: | LED print head 4 (EEPROM) communication error [black drum unit] The LED print head 4 (EEPROM) of the black drum unit does not communicate with the engine controller PWB (A0004) normally. The incompatible LED print head is installed to the printer. |
| Causes: | Defective LED print head 4. Installing the LED print head, which is incompatible with the printer specification. Defective engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Defective FFCs (S03011) between LED print head 4 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals.D |
| Remedy: | Defective LED print head 4. Replace the LED print head 4. See page 1- 5-15. Installing the LED print head, which is incompatible with the printer specification. Install the compatible LED print head to the black drum unit. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Replace the LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Check the continuity of the harness (S03214), check the insertion of YC3 of the engine controller PWB (A0004), if there is trouble, remedy or replace. Defective FFCs (S03011) between LED print head 4 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. Check the connection of the FFCs with the black drum unit and the printer main unit, check the continuity of the FFCs (S03011), check the connection of the LED print head 4, if there is trouble, remedy or replace. |
| Error code: | 0953 |
| Description: | LED print head 1 (EEPROM) communication error [magenta drum The LED print head 1 (EEPROM) the magenta drum unit does communicate with the engine controller PWB (A0004) normally. |
| Causes: | Defective LED print head 1. Installing the LED print head, which is incompatible with the printer specification. Defective engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Defective FFCs (S03011) between LED print head 1 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. |
| Remedy: | Defective LED print head 1. Replace the LED print head 1. See page 1- 5-15. Installing the LED print head, which is incompatible with the printer specification. Install the compatible LED print head to the black drum unit. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Replace the LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Check the continuity of the harness (S03214), check the insertion of YC3 of the engine controller PWB (A0004), if there is trouble, remedy or replace. Defective FFCs (S03011) between LED print head 1 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. Check the connection of the FFCs with the magenta drum unit and the printer main unit, check the continuity of the FFCs (S03011), check the connection of the LED print head 1, if there is trouble, remedy or replace. |
| Error code: | 0954 |
| Description: | LED print head 3 (EEPROM) communication error [yellow drum unit] The LED print head 3 (EEPROM) of the yellow drum unit does not communicate with the engine controller PWB (A0004) normally. |
| Causes: | Defective LED print head 3. Installing the LED print head, which is incompatible with the printer specification. Defective engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Defective FFCs (S03011) between LED print head 3 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. |
| Remedy: | Defective LED print head 3. Replace the LED print head 3. See page 1- 5-15. Installing the LED print head, which is incompatible with the printer specification. Install the compatible LED print head to the black drum unit. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Replace the LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Check the continuity of the harness (S03214), check the insertion of YC3 of the engine controller PWB (A0004), if there is trouble, remedy or replace. Defective FFCs (S03011) between LED print head 3 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. Check the connection of the FFCs with the magenta drum unit and the printer main unit, check the continuity of the FFCs (S03011), check the connection of the LED print head 3, if there is trouble, remedy or replace. |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1100 |
| Display: | Prepare for maint cart replacement. |
| Description: | Paper Jam There is paper jammed in the All-In-One. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Clear the paper jam, and resend the print job. |
| Error code: | 1110 |
| Description: | PF lift motor 2 error (large capacity feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 2 is turned on is excluded from detection. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 2 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF Lift motor2. PF Lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor 2 and PF main PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the PF Lift sensor 2. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1120 |
| Description: | Paper feeder left lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 1 does not turn on within 30 s of paper feeder lift motor 2 turning on. |
| Causes: | Poor contact in the connector terminals. Defective paper feeder lift switch 1. Defective paper feeder lift motor 2. The paper feeder left lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper feeder lift switch 1. Check if YC5-4 on the paper feeder main PWB goes low when paper feeder lift switch 1 is turned off. If not, replace paper feeder lift switch 1. Defective paper feeder lift motor 2. Check for continuity across the coil. If none, replace paper feeder lift motor 2. The paper feeder left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | 1130 |
| Description: | Paper feeder right lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 2 does not turn on within 30 s of paper feeder lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective paper feeder lift switch 2. Defective paper feeder lift motor 1. The paper feeder right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper feeder lift switch 2. Check if YC5-7 on the paper feeder main PWB goes low when paper feeder lift switch 2 is turned off. If not, replace paper feeder lift switch 2. Defective paper feeder lift motor 1. Check for continuity across the coil. If none, replace paper feeder lift motor 1. The paper feeder right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | 1140 |
| Description: | SD lift motor error (side deck) After cassette 5 is inserted, SD lift sensor does not turn on within 30 s. The lock signal of the motor is detected continuously for 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective SD lift motor. Defective SD main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. SD Lift motor 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SD Lift motor and SD main PWB (YC8) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SD Lift motor. SD Lift sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SD Lift sensor and SD main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the SD Lift sensor. SD main PWB Replace the SD main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1150 |
| Description: | Lift motor descent error *40/42 and 45/47 ppm printers (EUR/ USA model) only Optional bulk paper feeder’s tray bottom position sensor does not turn on. Lift motor lock error occurred 3 times. |
| Causes: | Defective bulk paper feeder’s tray bottom position sensor. Defective harness between bulk paper feeder’s tray bottom position sensor and main PWB (YC8), or improper connector insertion. Defective bulk paper feeder’s main PWB. |
| Remedy: | Defective bulk paper feeder’s tray bottom position sensor. Replace the bulk paper feeder’s tray bottom position sensor. Defective harness between bulk paper feeder’s tray bottom position sensor and main PWB (YC8), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective bulk paper feeder’s main PWB. Replace the bulk paper feeder’s main PWB. |
| Error code: | 1160 |
| Description: | Paper feeder PF-70*/PF-75 sequence problem |
| Causes: | Operation start request is sent from the printer to the paper feeder PF-70/PF-75 while paper feed is disabled. Paper feed request is sent from the printer to the paper feeder PF- 70/PF-75 before operation start request. |
| Remedy: | Turn the power off and back on (reset request is sent from the printer to the paper feeder PF-70/PF-75 to cancel operation start request). Turn the power off and back on (reset request is sent from the printer to the paper feeder PF-70/PF-75 to cancel operation start request). |
| Error code: | 1170 |
| Description: | Paper feeder PF-70*/PF-75* incorrect type problem |
| Causes: | Paper feeder for the copier is installed. |
| Remedy: | Replace the paper feeder fot the printer. |
| Error code: | 1200 |
| Description: | Side registration motor error The duplexer PWB of the optional duplexer cannot detect the home position of the adjust guide. |
| Causes: | Defective duplexer. Defective engine controller PWB (A0004). |
| Remedy: | Defective duplexer. Refer to the duplexer`s service manual. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). |
| Error code: | 2101 |
| Description: | Developer motor error After developer motor is driven, the ready signal does not turn to L within 2 s. After developer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor. Defective engine PWB. |
| Remedy: | Developer unit 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor 1. To check the motor operation, execute DLP(K) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor and Feed PWB 1 (YC8) Feed PWB 1 (YC2) and Engine PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor. Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2102 |
| Description: | Developer motor C error After developer motor C is driven, the ready signal does not turn to L within 5 s. After developer motor C is stabilized, the ready signal is at the H level for 5 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor C. Defective engine PWB. |
| Remedy: | Developer unit C 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor C 1. To check the motor operation, execute DLP(C) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor C and Motor control PWB (YC7) Motor control PWB (YC3) and Engine PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor C. Motor control PWB Replace the Motor control PWB Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2201 |
| Description: | drum motor steady-state error After drum motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor. Defective engine PWB. |
| Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. Drum motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2202 |
| Description: | Drum motor C steady-state error The motor revolution fluctuates more than +/-6.2% of the normal revolution for 5s continuously, after the drum motor C has stabilized. The counter achieved by timer capture is less than 2200 in 10 times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor C. Defective engine PWB. |
| Remedy: | Drum unit 1. Execute U030 Belt Meand (transfer Motor) and check that the drum motor can rotate. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the drum or the drum screw can rotate. 4. If it won’t rotate, replace the drum unit. Drum motor C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum motor C and Motor control PWB (YC4) Motor control PWB (YC3) and Engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum motor C. Motor control PWB Replace the Motor control PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2203 |
| Description: | Drum motor M steady-state error The motor revolution fluctuates more than +/-6.2% of the normal revolution for 5s continuously, after the drum motor M has stabilized. The counter achieved by timer capture is less than 2200 in 10 times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor M. Defective engine PWB. |
| Remedy: | Drum unit 1. Execute U030 Belt Meand (transfer Motor) and check that the drum motor can rotate. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the drum or the drum screw can rotate. 4. If it won’t rotate, replace the drum unit. Drum motor M 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum motor M and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum motor M. Motor control PWB Replace the Motor control PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2204 |
| Description: | Drum motor Y steady-state error The motor revolution fluctuates more than +/-6.2% of the normal revolution for 5s continuously, after the drum motor Y has stabilized. The counter achieved by timer capture is less than 2200 in 10 times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor Y. Defective engine PWB. |
| Remedy: | Drum unit 1. To check the motor operation, execute U030 Belt Meand (transfer motor).. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the drum or the drum screw can rotate. 4. If it won’t rotate, replace the drum unit. Drum motor Y 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum motor Y and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum motor Y. Motor control PWB Replace the Motor control PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2700 |
| Description: | 3-color release motor error When the color release motor is driven, the color release sensor does not turn on/off for 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective color release motor. Defective engine PWB. |
| Remedy: | Color release motor Color release sensor (Intermediate transfer belt unit) 1. To check the motor operation, execute U30 CMY Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Intermediate transfer belt unit and Engine PWB (YC3) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Intermediate transfer belt unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2710 |
| Description: | Waste toner box motor error • After the motor drive remote signal is turned on, the overcurrent detection signal is detected continuously for more than 200 ms. |
| Causes: | Overload on the waste toner box motor. Defective waster toner box motor. |
| Remedy: | Overload on the waste toner box motor. Check to see if the waste toner in the waste toner box is solidified. If any problem is found, replace the waste toner box. Defective waster toner box motor. Replace the waster toner box motor. |
| Error code: | 5100 |
| Description: | Short-circuited main charger output Five pages have been printed with the main charger output short-circuited. |
| Causes: | Drum unit installed incorrectly. Engine PWB installed incorrectly. Defective engine PWB |
| Remedy: | Drum unit installed incorrectly. Verify harness is not pinched in the drum unit. Engine PWB installed incorrectly. Verify harness is not pinched in the engine PWB. Defective engine PWB. Replace the engine PWB. |
| Error code: | 5301 |
| Description: | Broken cleaning lamp K wire When the cleaning lamp K is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit K and Drum relay PWB (YC2) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp K. Replace the drum unit K. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5302 |
| Description: | Broken cleaning lamp C wire When the cleaning lamp C is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp C. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit C and Drum relay PWB (YC4) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp C. Replace the drum unit C. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5303 |
| Description: | Broken cleaning lamp M wire When the cleaning lamp M is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp M. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit M and Drum relay PWB (YC3) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp M. Replace the drum unit M. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5304 |
| Description: | Broken cleaning lamp Y wire When the cleaning lamp Y is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp Y. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit Y and Drum relay PWB (YC5) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp Y. Replace the drum unit Y. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6050 |
| Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
| Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6100 |
| Description: | Broken fuser heater wire Fuser thermistor 5 won’t reach the reference temperature in 480 s after shifting to low power mode. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6120 |
| Description: | Abnormally high fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature higher than 190°C/ 374°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 5. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6130 |
| Description: | Broken fuser press thermistor 5 wire The input from the fuser press thermistor 5 has been less than 30°C/ 86°F (A/D: greater thann992) for 60 seconds continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) Fuser IH PWB(YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6150 |
| Description: | Abnormally low fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature lower than 30°C/ 86°F for 1 s after warming up. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 5. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 6410 |
| Description: | Fuser unit type mismatch problem Absence of the fuser unit is detected. |
| Causes: | Fuser unit connector inserted incorrectly. Different type of the fuser unit is installed. |
| Remedy: | Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. Different type of the fuser unit is installed. Install the correct fuser unit. |
| Error code: | 6420 |
| Description: | Fuser unit fuse cut problemctor. |
| Causes: | Poor contact in the connector terminals. Fuser unit connector inserted incorrectly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC10 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. |
| Error code: | 7001 |
| Description: | Toner motor error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB. |
| Remedy: | Toner container 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7002 |
| Description: | Toner motor C error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor C. Defective toner motor C. Defective engine PWB. |
| Remedy: | Toner container C 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Screw sensor C 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor C and Engine PWB (YC27) 3. Replace the screw sensor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7003 |
| Description: | Toner motor M error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor M. Defective toner motor M. Defective engine PWB. |
| Remedy: | Toner container M 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Screw sensor M 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor M and Engine PWB (YC27) 3. Replace the screw sensor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7004 |
| Description: | Toner motor Y error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor Y. Defective toner motor Y. Defective engine PWB. |
| Remedy: | Toner container Y 1. Check that the spiral screw of the toner container can be rotated by the hand. 1. Check for broken gears and replace if any. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Screw sensor Y 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor Y and Engine PWB (YC27) 3. Replace the screw sensor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7101 |
| Description: | Toner sensor error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7102 |
| Description: | Toner sensor C error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor C 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit C are not damaged and the spiral can rotate. 5. Replace the Developer unit C. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7103 |
| Description: | Toner sensor M error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor M 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit M are not damaged and the spiral can rotate. 5. Replace the Developer unit M. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7104 |
| Description: | Toner sensor Y error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor Y 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit Y are not damaged and the spiral can rotate. 5. Replace the Developer unit Y. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7200 |
| Display: | Jam MP Tray Remove the jammed paper from MP Tray and press [Retry]. |
| Description: | Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7210 |
| Description: | Short-circuited outer temperature sensor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7301 |
| Description: | Toner hopper motor error During the Toner hopper motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective toner hopper sensor. Defective toner hopper motor. Defective engine PWB. |
| Remedy: | Toner hopper motor 1. If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner hopper motor and Front PWB (YC5) Front PWB (YC3) and Engine PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the toner hopper motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7302 |
| Description: | Toner hopper motor C error During the Toner hopper motor C is driven, an event in which a locking was detected for 15 times in 200 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor Defective toner hopper sensor C. Defective toner hopper motor C. Defective engine PWB. |
| Remedy: | Toner hopper motor C 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner hopper motor C and retainer PWB (YC4) Retainer PWB (YC3) and front PWB (YC6) Front PWB (YC3) and engine PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Toner motor C. Screw sensor C 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor C and Engine PWB (YC27) 3. Replace the screw sensor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7303 |
| Description: | Toner hopper motor M error During the Toner hopper motor M is driven, an event in which a locking was detected for 15 times in 200 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective toner hopper sensor M. Defective toner hopper motor M. Defective engine PWB. |
| Remedy: | Toner hopper motor M 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner hopper motor M and retainer PWB (YC4) Retainer PWB (YC3) and front PWB (YC6) Front PWB (YC3) and engine PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Toner motor M. Screw sensor M 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor M and Engine PWB (YC27) 3. Replace the screw sensor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7304 |
| Description: | Toner hopper motor Y error During the Toner hopper motor Y is driven, an event in which a locking was detected for 15 times in 200 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective toner hopper sensor Y. Defective toner hopper motor Y. Defective engine PWB. |
| Remedy: | Toner hopper motor Y 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner hopper motor Y and retainer PWB (YC4) Retainer PWB (YC3) and front PWB (YC6) Front PWB (YC3) and engine PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Toner motor Y. Screw sensor Y 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor Y and Engine PWB (YC27) 3. Replace the screw sensor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7600 |
| Description: | Toner ID sensor error The detection signal of the toner ID sensor was abnormal value. |
| Causes: | Defective toner ID sensor. Defective engine controller PWB (A0004). Defective harness (S03195) between engine controller PWB (A0004) and toner ID sensor or poor contact of the connector terminals. |
| Remedy: | Defective toner ID sensor. Replace the toner ID sensor. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective harness (S03195) between engine controller PWB (A0004) and toner ID sensor or poor contact of the connector terminals. Check the continuity of the harness (S03195), check the connection YC11 connector of the engine controller PWB (A0004), if there is trouble, remedy or replace. |
| Error code: | 7610 |
| Description: | Image density measurement timing problem • The measured value of density patch is abnormal. |
| Causes: | Faulty density due to a mechanical cause. |
| Remedy: | Faulty density due to a mechanical cause. Check the drum unit, high voltage unit, developing unit, and transfer unit. If any problem is found, replace the unit. |
| Error code: | 7620 |
| Description: | Color Registration timing of detection Color patches printed on the primary transfer belt are not within the ID sensor readable range. Or the poor density occurs. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor LSU 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. 8. When checking the printing position of the color, if any color shift occurs, re-install the LSU and the drum unit. 9. If not corrected, replace the LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 8010 |
| Description: | Punch motor error 1 When the punch motor is driven, punch home position sensor does not turn on within 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch home position sensor. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch home position sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch home position sensor and Punch PWB (YC8) 4. Replace the Punch home position sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8020 |
| Description: | Punch motor error 2 Home position is not obtained in 3 s after home position is initialized or in standby. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8030 |
| Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8040 |
| Description: | Belt problem (document finisher) The belt sensor does not turn on/off within specified time of the belt solenoid turning on. |
| Causes: | Defective connector cable or poor contact in the connector. Defective belt sensor. Defective belt solenoid. Defective DF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Belt sensor and DF main PWB (CN10) Belt solenoid and DF main PWB (CN21) Defective belt sensor. Replace the belt sensor. Defective belt solenoid. Replace the belt solenoid. Defective DF main PWB. Replace the DF main PWB and check for correct operation. |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8150 |
| Description: | DF tray motor error 2 When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF main PWB (YC22) DF tray upper surface sensor and DF main PWB (YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8170 |
| Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8180 |
| Description: | DF side registration motor 1 error 2 JAM6810 (jam in front of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1. 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8190 |
| Description: | DF side registration motor 2 error 1 When initial operation, DF side registration sensor 2 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8220 |
| Description: | Stapler shift motor 2 error (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3.5 s passed. |
| Causes: | Poor contact in the connector terminals. Defective stapler shift motor 2. Defective finisher main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC10 on the finisher main PWB and the connector of stapler shift motor 2, and the continuity across the connector terminals. Repair or replace if necessary. Defective stapler shift motor 2. Replace stapler shift motor 2. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | 8230 |
| Description: | DF staple motor error 1 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF staple sensor Replace the staple unit. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8240 |
| Description: | DF staple motor error 2 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8300 |
| Description: | CF unit communication error Communication with the center- folding unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF set sensor. Defective PWB. |
| Remedy: | CF unit set switch 1. Execute U241 Booklet - Set to check the finisher switch. 2. Check that the switch and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main PWB (YC7) and DF main PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CF unit set switch. CF main PWB Replace the CF main PWB DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8310 |
| Description: | CF side registration motor 2 error When initial operation, CF side registration sensor 2 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 2. Defective CF side registration motor 2. Defective CF main PWB. |
| Remedy: | CF side registration motor 2 1. Execute U240 Booklet - Width Test to check finisher operation check. 2. Manipulate the side registration upper guide back and forth to check it can smoothly move back and forth. 3. Check that the drive from the motor reaches the side registration upper guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor. CF side registration sensor 2 1. Execute U241 Booklet - Width Up HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 2 and CF main PWB (YC20) 4. Replace the CF side registration sensor 2. CF main PWB Replace the CF main PWB |
| Error code: | 8320 |
| Description: | CF adjustment motor error When initial operation, CF adjustment sensor does not turn on within 2.5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF adjustment sensor 1, 2. Defective CF adjustment motor 1, 2. Defective CF main PWB. |
| Remedy: | CF adjustment motor1,2 1. Execute U240 Booklet - Bundle Up / Down to check the finisher operation. 2. Manipulate the fold moving belt up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold moving belt. (Check if the belt is bent.) 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment motor 1,2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF adjustment motor1,2 CF adjustment sensor1,2 1. Execute U241 Booklet - bundle Up / Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment sensor 1,2 and CF main PWB (YC20) 4. Replace the CF adjustment sensor1,2. CF main PWB Replace the CF main PWB. |
| Error code: | 8330 |
| Description: | CF blade motor error When initial operation, CF blade sensor does not turn on within 1500 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF blade sensor. Defective CF blade motor. Defective CF main PWB. |
| Remedy: | CF blade motor 1. Execute U240 Booklet - Blade to check the finisher operation. 2. Manipulate the fold blade up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold blade. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade motor and CF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF blade motor. CF blade sensor 1. Execute U241 Booklet - Blade HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade sensor and CF main PWB (YC20) 4. Replace the CF blade sensor. CF main PWB Replace the CF main PWB |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F030 |
| Description: | Main PWB system error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F060 |
| Description: | Engine RAM error |
| Causes: | Defective engine PWB. |
| Remedy: | Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | F070 |
| Description: | Communication error between System-CPU and Engine-CPU |
| Causes: | Switching regulator • Replace the fuse (F210). • Replace the switching regulator. LGC board SYS board If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the SYS board. IMG board If the problem is still not corrected with the replacement of the SYS board, reinstall the removed SYS board and replace the IMG board. |
| Remedy: | (1) Check if the connector CN104 on the SYS board and CN130, CN131, CN134 on the SYSIF board is disconnected. (2) Check if the connector CN10 on the SLG board is disconnected. (3) Check if the harness connecting the SYSIF board and SLG board is disconnected or open circuited. (4) Check if the harness connecting the SYSIF board and LGC board is disconnected or open circuited. (5) Check if the connection of the SYS board (CN104) and SYSIF board (CN130) is open circuited. (6) If the SYS board has been replaced, check if the jumper pin setting on the SYS board is correct. (The jumper pin should be inserted between pin 2 and 3 of CN103 and CN115.) (7) Check the version of the system ROM on the SYS board. (8) Check the version of the engine ROM version on the LGC board. (9) Check the version of the scanner ROM version on the SLG board. (10) Replace the SYS board. (11) Replace the SLG board. (12) Replace the LGC board. (13) Replace the SYSIF board. |
