Kyocera ECOSYS M3860idnf
Рейтинг
Модули
SCANNER SECTION
Finisher section 6
DP Covers
Finisher section 1
Finisher section 5
Finisher section 7
DP Assy
Paper Feed Section(Cassette/Duplex/MPF)
DP Drive Section
Finisher section 2
Finisher section 8
Exit Section
DRIVE SECTION
Finisher section 3
Finisher section 4
Finisher section 9
DP Frames
FRAME
Operation Section
Developer Section
Fuser Section
PAPER CASSETTE
DP Table Assy
DP Paper Conveying Section 1
Image Formation Section
DP Paper Feed Section
Paper Conveying Section
COVERS
DP Paper Conveying Section 2
Детали Finisher section 2
| Деталь: | BELT ISU |
| Парткод: | 302H917230 |
| Цена: | 1 000 ₽ |
| Деталь: | PULLEY TENSION |
| Парткод: | 302M417180 |
| Деталь: | MOUNT TENSION PULLEY |
| Парткод: | 3V2NM17210 |
| Деталь: | SPRING-COMPRESSION ISU BELT |
| Парткод: | 3V2NM17600 |
| Деталь: | PARTS MOTOR ISU SP |
| Парткод: | 302H994270 |
| Цена: | 6 000 ₽ |
| Деталь: | BUSHING FAN |
| Парткод: | 302JD19140 |
| Деталь: | MOUNT MOTOR ISU |
| Парткод: | 3V2NM17190 |
| Деталь: | GEAR Z63R-P32 ISU |
| Парткод: | 3V2NM17200 |
| Деталь: | SHAFT ISU |
| Парткод: | 3V2NM17270 |
| Деталь: | PARTS FRAME ISU TOP ASSY SP |
| Парткод: | 302TA94020 |
| Деталь: | TAPE FFC A |
| Парткод: | 3V2NM17310 |
| Деталь: | TAPE FFC B |
| Парткод: | 3V2NM17320 |
| Деталь: | TAPE FFC C |
| Парткод: | 3V2NM17490 |
| Деталь: | SLIDER ISU |
| Парткод: | 302H917450 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | SHEET FFC LEFT |
| Парткод: | 3V2NM17560 |
| Деталь: | PARTS ISU ASSY SP |
| Парткод: | 302WF93020 |
| Деталь: | SHAFT:BALANCER:GATHERING ROLLER |
| Парткод: | 302WF70640 |
| Деталь: | ARM:GATHERING ROLLER |
| Парткод: | 302WF70630 |
| Деталь: | SHAFTGATHERING ROLLER |
| Парткод: | 302WF70620 |
| Деталь: | TIMING BELT:B40S2M116 |
| Парткод: | 305J772400 |
| Деталь: | GATHERING ROLLER |
| Парткод: | 302WF70610 |
| Деталь: | TIMING PULLEY:GATHERING ROLLER:DRIVE:TRA |
| Парткод: | 305MC71T20 |
| Деталь: | SHAFTGATHERING ROLLER:DRIVE:ASSY |
| Парткод: | 302WF70600 |
| Деталь: | DISCHARGE BRUSH:GUIDE PLATE |
| Парткод: | 305MC71SV0 |
| Деталь: | GUIDE PLATE:EXIT:OPEN AND CLOSE |
| Парткод: | 302WF70530 |
| Деталь: | DRIVEN EXIT ROLLER |
| Парткод: | 305J770440 |
| Деталь: | SHAFT:EXIT ROLLER:DRIVEN |
| Парткод: | 302WF70540 |
| Деталь: | CUSHION:GUIDE PLATE:EXIT |
| Парткод: | 302WF70550 |
| Деталь: | DISCHARGE BRUSH:EXIT:OPEN AND CLOSE |
| Парткод: | 302WF70650 |
| Деталь: | SPRING PLATE:GUIDE PLATE:EXIT |
| Парткод: | 302WF70570 |
| Деталь: | PAWL:EXIT:OPEN AND CLOSE:ASSY |
| Парткод: | 302WF70560 |
| Деталь: | LEVER:SAFETY SWITCH |
| Парткод: | 302WF70590 |
| Деталь: | TENSION SPRING:RELEASE:DC SOLENOID |
| Парткод: | 302WF70090 |
| Деталь: | PHOTOINTERRUPTOR:FLAT:7MM |
| Парткод: | 305MC71230 |
| Деталь: | GEAR:SECTOR:EXIT:OPEN AND CLOSE |
| Парткод: | 302WF70580 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | 5HM40130 |
| Деталь: | GEAR:PULLEY:Z18/T20 |
| Парткод: | 302WF70670 |
| Деталь: | TIMING BELT:40S3M168 |
| Парткод: | 302WF70050 |
| Деталь: | SPACER |
| Парткод: | 305J771220 |
| Деталь: | GEAR:GATHERING ROLLER:DRIVE:Z20 |
| Парткод: | 302WF70660 |
| Деталь: | RETAINING RINGS-E:SILENCER:DIA4 |
| Парткод: | 305MC71T70 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 305JH74050 |
| Деталь: | COVER FRONTA |
| Парткод: | 302V018410 |
| Деталь: | COVER REAR A |
| Парткод: | 302V018430 |
| Деталь: | COVER PF |
| Парткод: | 302V018710 |
| Деталь: | COVER BASE DP |
| Парткод: | 302TA18850 |
| Деталь: | COVER FRONT B |
| Парткод: | 302TA18870 |
| Деталь: | COVER REAR B |
| Парткод: | 302TA18860 |
| Деталь: | EMBLEM |
| Парткод: | 302S018491 |
| Деталь: | COVER:EXIT:UPPER |
| Парткод: | 302WF70110 |
| Деталь: | COVER:EXIT:LEFT |
| Парткод: | 302WF70120 |
| Деталь: | COVER:EXIT:LOWER |
| Парткод: | 302WF70130 |
| Деталь: | TRAY:EXIT:FIX |
| Парткод: | 302WF70220 |
| Деталь: | INNER COVER:TRAY |
| Парткод: | 302WF70230 |
| Деталь: | TRAY:EXIT:MOVEABLE |
| Парткод: | 302WF70240 |
| Деталь: | TRAY:EXIT:AUXILIARY:SMALL |
| Парткод: | 302WF70410 |
| Деталь: | PHOTOINTERRUPTOR:FLAT:7MM |
| Парткод: | 305MC71230 |
| Деталь: | STAY:UPPER |
| Парткод: | 302WF70510 |
| Деталь: | PHOTO REFIECTION SENSOR:EXIT |
| Парткод: | 305J778480 |
| Деталь: | BRACKET:ENTRANCE SENSOR |
| Парткод: | 302WF70520 |
| Деталь: | TRANSPORT ROLLER:ENTRANCE |
| Парткод: | 302WF70680 |
| Деталь: | COMPRESSION SPRING:DRIVEN |
| Парткод: | 302WF70500 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | 305MM73ZY0 |
| Деталь: | GASKET:3X7X10 |
| Парткод: | 302WF70490 |
| Деталь: | GUIDE PLATE:TRANSPORT:UPPER |
| Парткод: | 302WF70140 |
| Деталь: | GUIDE:TRAILING EDGE |
| Парткод: | 302WF70480 |
| Деталь: | PRESSURE SPRING-14.5MM |
| Парткод: | 53018020 |
| Деталь: | BUSHING - ROLLER SLIDE |
| Парткод: | 305J771030 |
| Деталь: | DRIVEN ROLLER:SLIDE |
| Парткод: | 302WF70470 |
| Деталь: | DISCHARGE BRUSH:ENTRANCE |
| Парткод: | 302WF70460 |
| Деталь: | GUIDE PLATE:TRANSPORT:LOWER |
| Парткод: | 302WF70450 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | 5HM40130 |
| Деталь: | GEAR:TRANSPORT:Z25 |
| Парткод: | 302WF70690 |
| Деталь: | KNOB:TRANSPORT ROLLER:ENTRANCE |
| Парткод: | 302WF70150 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 302WF70020 |
| Деталь: | RETAINING RINGS-E:SILENCER:DIA4 |
| Парткод: | 305MC71T70 |
| Деталь: | CLAMP:LES-0503 |
| Парткод: | 305MC70G50 |
| Деталь: | DC STEPPER MOTOR:TRANSPORT:3.78W |
| Парткод: | 302WF70C10 |
| Деталь: | TENSION SPRING:TENSIONER:TRANSPORT |
| Парткод: | 302WF70850 |
| Деталь: | BRACKET:TENSIONER:TRANSPORT |
| Парткод: | 302WF70810 |
| Деталь: | GEAR:IDLER:Z35 |
| Парткод: | 302WF70840 |
| Деталь: | GEAR:RETURN:DRIVE:Z25 |
| Парткод: | 302WF70190 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | 5HM40130 |
| Деталь: | SHAFT:DRIVE:TRANSMISSION:ROLLER:RETURN |
| Парткод: | 302WF70740 |
| Деталь: | GEAR:RETURN:DRIVE:TRANSMISSION:Z31 |
| Парткод: | 302WF70750 |
| Деталь: | GEAR:ROLLER:RETURN:MIDDLE:Z28 |
| Парткод: | 302WF70770 |
| Деталь: | GEAR:ROLLER:RETURN:MIDDLE:Z25 |
| Парткод: | 302WF70760 |
| Деталь: | REVERSE ROLLER:TRAILING EDGE:Z20 |
| Парткод: | 302WF70780 |
| Деталь: | ARM:REVERSE ROLLER |
| Парткод: | 302WF70790 |
| Деталь: | SHAFT - REVERSE ROLLER |
| Парткод: | 302WF70100 |
| Деталь: | TRANSPORT ROLLER:SLIDE |
| Парткод: | 302WF70160 |
| Деталь: | BUSHING:ROLLER:SLIDE |
| Парткод: | 302WF70710 |
| Деталь: | EXIT ROLLER:RIGHT |
| Парткод: | 302WF70170 |
| Деталь: | EXIT ROLLER:LEFT |
| Парткод: | 302WF70180 |
| Деталь: | SHAFT:EXIT:COUPLING |
| Парткод: | 302WF70A20 |
| Деталь: | GEAR: EXIT:COU PLING :Z20 |
| Парткод: | 302WF70A30 |
| Деталь: | GEAR:EXIT:COUPLING:MIDDLE:Z19 |
| Парткод: | 302WF70A40 |
| Деталь: | CUSHION:PLATE:RETURN |
| Парткод: | 302WF70A00 |
| Деталь: | BRACKET:EXIT:CONNECTING |
| Парткод: | 302WF70A10 |
| Деталь: | TIMING PULLEY:EXIT ROLLER:DRIVE |
| Парткод: | 302WF70730 |
| Деталь: | TIMING PULLEY:EXIT ROLLER:DRIVE |
| Парткод: | 302WF70720 |
| Деталь: | GEAR:TRANSPORT:Z25 |
| Парткод: | 302WF70690 |
| Деталь: | LINK:ROLLER:SLIDE:ASSY |
| Парткод: | 302WF70700 |
| Деталь: | SPACER - 5.7X16X1.5 |
| Парткод: | 305J770650 |
| Деталь: | TIMING BELT:40S2M172 |
| Парткод: | 305MM70AR0 |
| Деталь: | GEAR: PULLEY:Z25/T20 |
| Парткод: | 302WF70820 |
| Деталь: | GEAR:IDLER:Z22 |
| Парткод: | 302WF70830 |
| Деталь: | GEAR:IDLER:Z22:LIGHTER |
| Парткод: | 302WF70800 |
| Деталь: | SCREW CONTACT POINT |
| Парткод: | 305H780730 |
| Деталь: | RETAINING RINGS-E:SILENCER:DIA4 |
| Парткод: | 305MC71T70 |
| Деталь: | E END RING 4 |
| Парткод: | 54930350 |
| Деталь: | PARTS DP UNIT SP |
| Парткод: | 302WF93010 |
| Деталь: | PARTS ROLLER DU ASSY SP |
| Парткод: | 302LV94530 |
| Деталь: | PULLEY PA |
| Парткод: | 302LV24760 |
| Деталь: | ACTUATOR PE |
| Парткод: | 302LV29090 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | SPRING ACTUATOR MPF |
| Парткод: | 302LV08201 |
| Деталь: | ACTUATOR MPF |
| Парткод: | 302LV08180 |
| Цена: | 180 ₽ |
| Деталь: | ROLLER M/P ASSY |
| Парткод: | 302HS08260 |
| Цена: | 700 ₽ |
| Деталь: | PULLEY FEED |
| Парткод: | 3V2LV08210 |
| Деталь: | PAD SEPARATOR MPF |
| Парткод: | 302F908250 |
| Цена: | 700 ₽ |
| Деталь: | HOLDER SEPARATION MPF |
| Парткод: | 3V2LV08070 |
| Деталь: | SHEET GUIDE TURN A |
| Парткод: | 302LV08220 |
| Деталь: | LEVER CAM MPF |
| Парткод: | 3V2LV08090 |
| Деталь: | GUIDE FEED SIDE |
| Парткод: | 3V2LV06030 |
| Деталь: | SPRING PICKUP B |
| Парткод: | 3V2LV06090 |
| Деталь: | PULLEY PICKUP ASSY |
| Парткод: | 302HN06080 |
| Цена: | 480 ₽ |
| Деталь: | PULLEY FEED ASSY |
| Парткод: | 302F906230 |
| Цена: | 750 ₽ |
| Деталь: | GEAR FEED Z30H |
| Парткод: | 302F906280 |
| Деталь: | GEAR FEED Z26H |
| Парткод: | 302F906030 |
| Деталь: | BUSH 4 |
| Парткод: | 302K306460 |
| Деталь: | PARTS HOLDER FEED ASSY SP |
| Парткод: | 302LV94270 |
| Цена: | 2 500 ₽ |
| Деталь: | PARTS PWB ASSY CIS CONNECT SP |
| Парткод: | 302V194070 |
| Деталь: | PARTS MOTOR PAPER FEED SP |
| Парткод: | 303R494040 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | GEAR FEED Z53R Z33R |
| Парткод: | 303R431050 |
| Деталь: | GEAR CONVEYING Z54R Z32L |
| Парткод: | 303R431200 |
| Деталь: | GEAR 25R |
| Парткод: | 303LM31040 |
| Деталь: | GEAR Z32L |
| Парткод: | 303R431250 |
| Деталь: | PARTS CLUTCH 35 Z35R SP |
| Парткод: | 302NR94010 |
| Деталь: | DC BRUSH MOTOR:EXIT:ASSY:7.7W |
| Парткод: | 302WF70430 |
| Деталь: | BUSHING - M6 |
| Парткод: | 302WF70060 |
| Деталь: | SCREW:M2.6X3 |
| Парткод: | 302WF70080 |
| Деталь: | GEAR:Z20/Z35 |
| Парткод: | 302WF70920 |
| Деталь: | GEAR:Z37:WORM GEAR |
| Парткод: | 302WF70930 |
| Деталь: | CAM:TRAY:MOVEABLE |
| Парткод: | 302WF70940 |
| Деталь: | GEAR:DRIVE:CAM:Z42 |
| Парткод: | 302WF70950 |
| Деталь: | BRACKET:DC MOTOR:TRAY:PEEN |
| Парткод: | 302WF70250 |
| Деталь: | SHAFT:CAM:TRAY |
| Парткод: | 302WF70260 |
| Деталь: | E END RING 4 |
| Парткод: | 54930350 |
| Деталь: | RETAINING RINGS-E:SILENCER:DIA4 |
| Парткод: | 305MC71T70 |
| Деталь: | PLATE:TRAILING EDGE:STANDARD FENCE |
| Парткод: | 302WF70B30 |
| Деталь: | CUSHION:ARM:RETURN:0.2MM |
| Парткод: | 302WF70B80 |
| Деталь: | STANDARD FENCE:TRAILING EDGE |
| Парткод: | 302WF70B40 |
| Деталь: | GUIDE:STANDARD FENCE:FRONT RIGHT |
| Парткод: | 302WF70B10 |
| Деталь: | GUIDE:STANDARD FENCE:REAR RIGHT |
| Парткод: | 302WF70B20 |
| Деталь: | JOGGER FENCE:REAR |
| Парткод: | 302WF70A50 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 305MM74ZE0 |
| Деталь: | SHAFT:GUIDE:JOGGER:FRONT |
| Парткод: | 302WF70A60 |
| Деталь: | TRAY:STAPLE |
| Парткод: | 302WF70B50 |
| Деталь: | STANDARD FENCE:FIX:FRONT |
| Парткод: | 302WF70B60 |
| Деталь: | PHOTO REFLECTION SENSOR - PS-17ND1 |
| Парткод: | 305HM21541 |
| Деталь: | BRACKET:SURFACE OF PAPER SENSOR:STAPLER |
| Парткод: | 302WF70A80 |
| Деталь: | PHOTOINTERRUPTOR:ENTRANCE |
| Парткод: | 302WF70070 |
| Деталь: | BRACKET:DC STEPPER MOTOR:JOGGER |
| Парткод: | 302WF70A90 |
| Деталь: | DC STEPPER MOTOR:JOGGER:1.48W |
| Парткод: | 305MC71EH0 |
| Деталь: | STAY:JOGGER |
| Парткод: | 302WF70B70 |
| Деталь: | TENSIONER:JOGGER FENCE |
| Парткод: | 302WF70B90 |
| Деталь: | TENSION SPRING:BELT TENSIONER:JOGGER FEN |
| Парткод: | 302WF70C00 |
| Деталь: | TIMING PULLEY - 18T |
| Парткод: | 305MM74AL0 |
| Деталь: | TIMING BELT - 2XL |
| Парткод: | 302WF70040 |
| Деталь: | BRACKET:HOME POSITION SENSOR:JOGGER:REAR |
| Парткод: | 302WF70A70 |
| Деталь: | PHOTOINTERRUPTOR:GP1A173LCS5F |
| Парткод: | 302WF70C30 |
| Деталь: | CUSHION:GATE PAWL |
| Парткод: | 305J771860 |
| Деталь: | RETAINING RINGS-E:SILENCER:DIA4 |
| Парткод: | 305MC71T70 |
| Деталь: | CLAMP:LWSM-0306A |
| Парткод: | 305MC70G60 |
| Деталь: | CLAMP:LES-0503 |
| Парткод: | 305MC70G50 |
| Деталь: | CLAMP:JDW-1S |
| Парткод: | 305MC70G80 |
| Деталь: | STANDARD FENCE:TRAILING EDGE:SUB-ASSY |
| Парткод: | 302WF70B00 |
| Деталь: | COVER REAR LOW |
| Парткод: | 302TP04210 |
| Деталь: | COVER REAR UP |
| Парткод: | 302LV04100 |
| Деталь: | GUIDE CHANGE |
| Парткод: | 3V2LV28081 |
| Деталь: | GEAR Z22S A |
| Парткод: | 302LV28100 |
| Деталь: | GEAR Z20S |
| Парткод: | 302LV28090 |
| Деталь: | GEAR Z22S B |
| Парткод: | 302LV28191 |
| Деталь: | SHAFT EXIT LOW |
| Парткод: | 3V2LV28270 |
| Деталь: | ACTUATOR DU |
| Парткод: | 3V2LV28070 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | LABEL PUSH |
| Парткод: | 302MC34040 |
| Деталь: | PARTS ROLLER REAR SP |
| Парткод: | 302WD94020 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302TP04230 |
| Деталь: | PARTS MOTOR EJECT SP |
| Парткод: | 302T994050 |
| Цена: | 4 400 ₽ |
| Деталь: | GEAR Z17S |
| Парткод: | 302WF28100 |
| Деталь: | GEAR Z66R-Z40S |
| Парткод: | 302LV28031 |
| Цена: | 90 ₽ |
| Деталь: | GEAR Z47S |
| Парткод: | 302WF28080 |
| Деталь: | GEAR Z20S |
| Парткод: | 302WF28090 |
| Деталь: | GEAR Z22S |
| Парткод: | 302WF28210 |
| Деталь: | GEAR Z17S |
| Парткод: | 302LV28040 |
| Цена: | 60 ₽ |
| Деталь: | ACTUATOR OVERFLOW |
| Парткод: | 302LV28141 |
| Цена: | 120 ₽ |
| Деталь: | PULLEY EXIT |
| Парткод: | 3V2LV28150 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | SPONGE EXIT |
| Парткод: | 302WF28300 |
| Деталь: | COVER REAR TOP A |
| Парткод: | 302WF04110 |
| Деталь: | LABEL JAM FINISHER |
| Парткод: | 302WF34020 |
| Деталь: | PARTS FAN COOLING 50 SET SP |
| Парткод: | 302WF94070 |
| Деталь: | PARTS FILTER SET SP |
| Парткод: | 302WF94080 |
| Деталь: | PARTS COVER REAR ASSY SP |
| Парткод: | 302TP94020 |
| Деталь: | PARTS CLUTCH 35 Z35R SP |
| Парткод: | 302NR94010 |
| Деталь: | PARTS CLUTCH 20-2W Z35R |
| Парткод: | 302LV94161 |
| Деталь: | SPRING INPUT MPF |
| Парткод: | 302HN31650 |
| Цена: | 150 ₽ |
| Деталь: | GEAR Z32L REG CL |
| Парткод: | 302LV31440 |
| Деталь: | GEAR Z26L DLP CLUTCH |
| Парткод: | 302LV31180 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 302KV94520 |
| Деталь: | HOLDER CLUTCH |
| Парткод: | 3V2P702110 |
| Деталь: | SPRING COUPLING DRUM |
| Парткод: | 302LV31290 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 3V2C904550 |
| Деталь: | CUT WASHER 7 |
| Парткод: | 302K914570 |
| Деталь: | GEAR Z119R |
| Парткод: | 302LV31050 |
| Деталь: | GEAR Z80R-Z36L |
| Парткод: | 302LV31060 |
| Деталь: | PLATE DRIVE |
| Парткод: | 302LV31010 |
| Деталь: | PARTS MOTOR-BL W30 SP |
| Парткод: | 302K394202 |
| Деталь: | LEVER COUPLING DRUM |
| Парткод: | 3V2LV31300 |
| Деталь: | GEAR Z34S INPUT |
| Парткод: | 302HN25180 |
| Деталь: | GEAR Z46L FREE |
| Парткод: | 3V2LV31120 |
| Деталь: | GEAR Z37S FREE |
| Парткод: | 3V2LV31130 |
| Деталь: | PARTS DC MOTOR ASSY SP |
| Парткод: | 302LV94230 |
| Деталь: | GEAR Z46S-Z13S |
| Парткод: | 302HN31040 |
| Деталь: | GEAR Z36L-Z20S |
| Парткод: | 302HN31030 |
| Деталь: | GEAR Z35S-Z13S B |
| Парткод: | 3V2LV31490 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP03072001+H01 |
| Деталь: | GUIDE CASSETTE R |
| Парткод: | 3V2LV02043 |
| Деталь: | GUIDE CASSETTE L |
| Парткод: | 3V2LV02051 |
| Деталь: | PARTS DRIVE FEED ASSY SP |
| Парткод: | 302LV94253 |
| Цена: | 5 400 ₽ |
| Деталь: | CAM:ROLLER:SLIDE |
| Парткод: | 302WF70870 |
| Деталь: | PHOTOINTERRUPTOR:FLAT:7MM |
| Парткод: | 305MC71230 |
| Деталь: | BRACKET:DC STEPPER MOTOR:SLIDE:ASSY |
| Парткод: | 302WF70200 |
| Деталь: | STAPLER:EH-C590R10-MT:ASSY |
| Парткод: | 302WF70280 |
| Деталь: | BRACKET:DC STEPPER MOTOR:GATHERING ROLLE |
| Парткод: | 302WF70400 |
| Деталь: | DC STEPPER MOTOR:PM |
| Парткод: | 305MC71EJ0 |
| Деталь: | PHOTOINTERRUPTOR:GP1A173LCS5F |
| Парткод: | 302WF70C30 |
| Деталь: | CAM:LEVER:GATHERING ROLLER |
| Парткод: | 302WF70900 |
| Деталь: | LEVER:GATHERING ROLLER |
| Парткод: | 302WF70910 |
| Деталь: | DC STEPPER MOTOR: EXIT:3.78W |
| Парткод: | 302WF70C20 |
| Деталь: | BRACKET:DC STEPPER MOTOR:EXIT |
| Парткод: | 302WF70860 |
| Деталь: | TIMING BELT - 40S3M144 |
| Парткод: | 305MA70300 |
| Деталь: | GEAR:MIDDLE:EXIT:OPEN AND CLOSE:Z15/Z51 |
| Парткод: | 302WF70890 |
| Деталь: | BRACKET:DC STEPPER MOTOR:EXIT:OPEN AND C |
| Парткод: | 302WF70880 |
| Деталь: | BRACKET:STAPLER:PEEN |
| Парткод: | 302WF70270 |
| Деталь: | CLAMP:LWSM-0306A |
| Парткод: | 305MC70G60 |
| Деталь: | CLAMP:LWSM-0605A |
| Парткод: | 305MA70160 |
| Деталь: | CLAMPS:WES-0507 |
| Парткод: | 305JW70070 |
| Деталь: | CLAMPS:WES-1210 |
| Парткод: | 305JW70080 |
| Деталь: | PCB:FIN:ASSY |
| Парткод: | 302WF70290 |
| Деталь: | COVER:PCB |
| Парткод: | 302WF70300 |
| Деталь: | GUIDE:HARNESS:ENTRANCE |
| Парткод: | 302WF70310 |
| Деталь: | HARNESS:INTERFACE |
| Парткод: | 302WF70330 |
| Деталь: | HARNESS:TRAY:STAPLE |
| Парткод: | 302WF70340 |
| Деталь: | HARNESS:MOTOR:MIDDLE |
| Парткод: | 302WF70350 |
| Деталь: | HARNESS:MOTOR:INNER BACK |
| Парткод: | 302WF70360 |
| Деталь: | HARNESS:MOTOR:FRONT |
| Парткод: | 302WF70370 |
| Деталь: | HARNESS:SENSOR |
| Парткод: | 302WF70380 |
| Деталь: | HEAT RADIATION SHEET:PCB |
| Парткод: | 302WF70390 |
| Деталь: | END FENCE:EXIT |
| Парткод: | 302WF70210 |
| Деталь: | SPRING PLATE:DOOR SWITCH:STAPLE EXCHANGE |
| Парткод: | 302WF70440 |
| Деталь: | BRACKET:DOOR SWITCH:STAPLE EXCHANGE |
| Парткод: | 302WF70320 |
| Деталь: | CLAMP:LWSM-0605A |
| Парткод: | 305MA70160 |
| Деталь: | MICROSWITCH:D3V-16506-3C25 |
| Парткод: | 302WF70030 |
| Деталь: | PHOTOINTERRUPTOR:GP1A173LCS5F |
| Парткод: | 302WF70C30 |
| Деталь: | SCREW:CONTACT POINT:M3 |
| Парткод: | 305MC71EA0 |
| Деталь: | BRACKET:PAPER SENSER |
| Парткод: | 302WF70960 |
| Деталь: | BRACKET:SOLENOID:PAPER SENSER |
| Парткод: | 302WF70970 |
| Деталь: | ARM:PAPER SENSER:TRAILING EDGE:ASSY |
| Парткод: | 302WF70420 |
| Деталь: | DC SOLENOID:PAPER SENSER:SUB-ASSY |
| Парткод: | 302WF70980 |
| Деталь: | TORSION SPRING:LEVER |
| Парткод: | 302WF70990 |
| Деталь: | CLAMP:LWSM-0605A |
| Парткод: | 305MA70160 |
| Деталь: | CLAMP:LWSM-0511A |
| Парткод: | 305HM40640 |
| Деталь: | Hinge Right |
| Парткод: | 303R302031 |
| Деталь: | Hinge Left |
| Парткод: | 303R402032 |
| Деталь: | FOOT |
| Парткод: | 302HN02611 |
| Деталь: | PARTS PWB ASSY CONNECT-L SP |
| Парткод: | 302WF94060 |
| Деталь: | FAN LSU 60-25 |
| Парткод: | 302GR44080 |
| Цена: | 2 800 ₽ |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | GUIDE CONTAINER |
| Парткод: | 302LV11240 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44010 |
| Деталь: | PARTS PWB ASSY TH CONNECT SP |
| Парткод: | 302LV94220 |
| Деталь: | PARTS PWB ASSY ENGINE SP |
| Парткод: | 302WF94050 |
| Деталь: | PARTS PWB ASSY MAIN SP |
| Парткод: | 302WF94040 |
| Деталь: | PARTS PWB ASSY MAIN SP EU |
| Парткод: | 302WF94030 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | PARTS PWB ASSY SWITCH SP |
| Парткод: | 302LV94210 |
| Деталь: | PARTS,FAN COOLING CONVEYING SP |
| Парткод: | 302FZ94420 |
| Деталь: | PARTS UNIT LOW VOLTAGE 100V SP |
| Парткод: | 302WF94020 |
| Деталь: | PARTS UNIT LOW VOLTAGE 230V SP |
| Парткод: | 302WF94010 |
| Деталь: | LK-3290 |
| Парткод: | 302TA93010 |
| Деталь: | PARTS FAX UNIT E SP |
| Парткод: | 303PA94011 |
| Деталь: | PARTS FAX UNIT U SP |
| Парткод: | 302R794340 |
| Деталь: | SCREW BOX |
| Парткод: | 302F939082 |
| Деталь: | COVER SENSOR |
| Парткод: | 3V2LV02990 |
| Деталь: | SHEET FAN L |
| Парткод: | 302LV02610 |
| Деталь: | PARTS STORAGE DEVICE SP |
| Парткод: | 302NH93190 |
| Деталь: | COVER LCD UPPER UT |
| Парткод: | 302TA05320 |
| Деталь: | PARTS TABLET OPERATION SP |
| Парткод: | 302NM94121 |
| Деталь: | PARTS LCD OPERATION SP |
| Парткод: | 302V194080 |
| Деталь: | LEVER LCD |
| Парткод: | 3V2NM05220 |
| Деталь: | COVER LCD LOWER |
| Парткод: | 302TA05040 |
| Деталь: | COVER CARD READER |
| Парткод: | 3V2NM05240 |
| Деталь: | LID OPERATION LEFT |
| Парткод: | 302TA05070 |
| Деталь: | COVER PANEL LEFT |
| Парткод: | 3V2NM05060 |
| Деталь: | LABEL OPERATION LEFT ENG |
| Парткод: | 302TA05140 |
| Деталь: | COVER OPERATION LEFT |
| Парткод: | 302TA05020 |
| Деталь: | KEY STATUS T |
| Парткод: | 302S505140 |
| Деталь: | KEY COPY |
| Парткод: | 302TA05060 |
| Деталь: | PARTS PWB ASSY H PANEL KEY-L SP |
| Парткод: | 302NM94100 |
| Деталь: | LID OPERATION RIGHT |
| Парткод: | 302TA05080 |
| Деталь: | COVER PANEL RIGHT |
| Парткод: | 3V2NM05050 |
| Деталь: | LABEL OPERATION RIGHT ENG |
| Парткод: | 302TA05130 |
| Деталь: | COVER OPERATION RIGHT |
| Парткод: | 302TA05010 |
| Деталь: | KEY MENU |
| Парткод: | 302TA05110 |
| Деталь: | KEY LOGOUT |
| Парткод: | 302S505120 |
| Деталь: | KEY 10 |
| Парткод: | 302TA05050 |
| Деталь: | PARTS PWB ASSY H PANEL KEY-R SP |
| Парткод: | 302TA94090 |
| Деталь: | PARTS PWB ASSY H PANEL MAIN SP |
| Парткод: | 302WF94090 |
| Деталь: | PARTS LCD UNIT UT SP |
| Парткод: | 302TA94130 |
| Деталь: | DV-3100 |
| Парткод: | 302LV93081 |
| Деталь: | FK-3300 |
| Парткод: | 302TA93040 |
| Деталь: | FK-3302 |
| Парткод: | 302TA93050 |
| Деталь: | HOLDER RETARD B |
| Парткод: | 3V2LV09311 |
| Деталь: | GUIDE RETARD C |
| Парткод: | 302LV09340 |
| Деталь: | SPRING RETARD B |
| Парткод: | 302LV09330 |
| Деталь: | RETARD ROLLER ASSY |
| Парткод: | 302F909171 |
| Цена: | 900 ₽ |
| Деталь: | GEAR CASSETTE /A-49 CASSETTE A4 |
| Парткод: | 5MVG127DN071 |
| Деталь: | GEAR Z48S LIFT |
| Парткод: | 302LV09241 |
| Деталь: | GEAR Z15S JOINT |
| Парткод: | 302LV09220 |
| Деталь: | COVER LIFT GEAR |
| Парткод: | 302LV09201 |
| Деталь: | CURSOR RIGHT B |
| Парткод: | 302LV09351 |
| Деталь: | CURSOR LEFT |
| Парткод: | 302LV09071 |
| Деталь: | CURSOR END |
| Парткод: | 3V2LV09090 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302F909211 |
| Деталь: | CT-3230 |
| Парткод: | 302TP93011 |
| Деталь: | LABEL CAUTION CIS |
| Парткод: | 302TA34040 |
| Деталь: | GEAR CASSETTE /A-49 CASSETTE A4 |
| Парткод: | 5MVG127DN071 |
| Деталь: | PARTS TABLE MAIN ASSY SP |
| Парткод: | 302TA94010 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302K994580 |
| Деталь: | ACTUATOR EXIT |
| Парткод: | 303R424150 |
| Деталь: | MC-3100 |
| Парткод: | 302LV93011 |
| Деталь: | WT-3200 |
| Парткод: | 302WD93010 |
| Деталь: | PARTS TONER FULL DETECT ASSY SP |
| Парткод: | 302LV94121 |
| Деталь: | STOPPER PROCESS |
| Парткод: | 302LV02110 |
| Деталь: | STOPPER PROCESS L |
| Парткод: | 302LV02200 |
| Деталь: | SHUTTER WASTE |
| Парткод: | 3V2LV02830 |
| Деталь: | DK-3190(E) |
| Парткод: | 302T693031 |
| Деталь: | DK-3192(U) |
| Парткод: | 302T693041 |
| Деталь: | DK-3194(AO) |
| Парткод: | 302T693061 |
| Деталь: | PARTS PULLEY PICKUP ASSY SP |
| Парткод: | 302R494420 |
| Деталь: | GUIDE READING |
| Парткод: | 303R424220 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 303NW94040 |
| Деталь: | PARTS CIS SP |
| Парткод: | 303R494050 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302K994580 |
| Деталь: | PAD SEPARATION |
| Парткод: | 302LW07100 |
| Деталь: | PARTS HOLDER PICUP ASSY SP |
| Парткод: | 303R494010 |
| Деталь: | PARTS HOLDER PAD ASSY SP |
| Парткод: | 303R394030 |
| Деталь: | PARTS ROLLER TRANSFER SP |
| Парткод: | 302LV94130 |
| Цена: | 3 000 ₽ |
| Деталь: | BUSH TRANSFER R |
| Парткод: | 302F924190 |
| Цена: | 150 ₽ |
| Деталь: | BUSH TRANSFER L |
| Парткод: | 302LV24360 |
| Деталь: | GEAR Z22R TC |
| Парткод: | 302LV24140 |
| Деталь: | SPRING TRANSFER R |
| Парткод: | 302LV24280 |
| Деталь: | SPRING TRANSFER L |
| Парткод: | 302LV24290 |
| Деталь: | PARTS GUIDE PAPER CHUTE SP |
| Парткод: | 302LV94261 |
| Деталь: | PARTS ROLLER REGIST UP SP |
| Парткод: | 302LV94180 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302LV24520 |
| Деталь: | GEAR Z19R-Z22R REGIST UP |
| Парткод: | 302LV24160 |
| Деталь: | PARTS ROLLER REGIST LOW SP |
| Парткод: | 302LV94170 |
| Деталь: | GEAR Z22L REGIST LOW |
| Парткод: | 302LV24150 |
| Деталь: | SHEET REGIST |
| Парткод: | 302LV24220 |
| Деталь: | PARTS PWB ASSY DRUM CONNECT SP |
| Парткод: | 302T694080 |
| Деталь: | GEAR Z35R IDLE |
| Парткод: | 302HS31140 |
| Деталь: | ACTUATOR ENVELOPE |
| Парткод: | 302LV24450 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | LOCK ENVELOPE R |
| Парткод: | 3V2LV24510 |
| Деталь: | LOCK ENVELOPE L |
| Парткод: | 3V2LV24440 |
| Деталь: | ACTUATOR DU |
| Парткод: | 3V2LV24111 |
| Деталь: | ACTUATOR IMAGE |
| Парткод: | 302LV24100 |
| Деталь: | PARTS ROLLER MIDDLE SET SP |
| Парткод: | 302P794090 |
| Деталь: | PARTS HIGH VOLTAGE UNIT SP |
| Парткод: | 302LV94060 |
| Цена: | 7 300 ₽ |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | COVER RIGHT |
| Парткод: | 302WF04020 |
| Деталь: | COVER RIGHT B |
| Парткод: | 302WF04260 |
| Деталь: | COVER RIGHT UP A |
| Парткод: | 302WF04030 |
| Деталь: | COVER WIFI |
| Парткод: | 302WF04220 |
| Деталь: | COVER SIDE RIGHT |
| Парткод: | 302WF04050 |
| Деталь: | COVER RIGHT UP B |
| Парткод: | 302WF04040 |
| Деталь: | COVER RIGHT REAR LOW |
| Парткод: | 302TP04221 |
| Деталь: | COVER CONTROLLER |
| Парткод: | 302WF04200 |
| Деталь: | COVER CONT UP B |
| Парткод: | 302WF04160 |
| Деталь: | COVER CONTROLLER UP |
| Парткод: | 302WF04210 |
| Деталь: | COVER LEFT |
| Парткод: | 302WF04170 |
| Деталь: | COVER SIDE LEFT INNER |
| Парткод: | 302WD04060 |
| Деталь: | COVER SIDE LEFT |
| Парткод: | 302WD04040 |
| Деталь: | COVER LEFT REAR |
| Парткод: | 302TP04200 |
| Деталь: | COVER LEFT UP C |
| Парткод: | 302WF04190 |
| Деталь: | COVER LEFT UP A |
| Парткод: | 302WF04250 |
| Деталь: | COVER LEFT UP B |
| Парткод: | 302WF04150 |
| Деталь: | COVER REAR TOP B |
| Парткод: | 302WF04120 |
| Деталь: | COVER STAY |
| Парткод: | 302WF04080 |
| Деталь: | LID TOP |
| Парткод: | 302WF04010 |
| Деталь: | KEY COVER OPEN |
| Парткод: | 302TA04040 |
| Деталь: | COVER FRONT |
| Парткод: | 302TA04030 |
| Деталь: | HOOK LID TOP A |
| Парткод: | 302TA04050 |
| Деталь: | HOOK LID TOP B |
| Парткод: | 302WF04180 |
| Деталь: | PARTS COVER MPF ASSY SP |
| Парткод: | 302TP94010 |
| Деталь: | LEVER LINK |
| Парткод: | 3V2LV08100 |
| Деталь: | SHEET MACHINE NUMBER |
| Парткод: | 302WF34010 |
| Деталь: | COVER FINISHER FRONT |
| Парткод: | 302WF04230 |
| Деталь: | LABEL LEVERA |
| Парткод: | 302LV34210 |
| Деталь: | PARTS SPEAKER SP |
| Парткод: | 302LC94370 |
| Деталь: | PARTS ROLLER CIS SP |
| Парткод: | 303R494060 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | ACTUATOR ORIGINAL |
| Парткод: | 303R407100 |
| Деталь: | PARTS PWB ASSY TX SP |
| Парткод: | 302TA94070 |
| Деталь: | PARTS PWB ASSY RX SP |
| Парткод: | 302TA94081 |
| Деталь: | PULLEY REGISTRATION BK |
| Парткод: | 303M824220 |
Коды ошибок
0100
0120
0130
0140
0150
0160
0170
0180
0190
0800
0840
1010
1020
1030
1040
1050
1800
1810
1820
1830
1900
1920
1930
2000
2010
2200
2210
2330
2340
2600
2610
2620
2630
3100
3200
3210
3500
4000
4101
5100
6000
6020
6030
6120
6130
6400
7100
7400
7410
7800
7810
7900
9200
9220
F000
F010
F020
F040
F050
Описание
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0130 |
| Description: | There is a problem with Thermistor for Print Heater. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0140 |
| Description: | There is a problem with Thermistor for dryer. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0180 |
| Description: | Even though the machine carries out the regular movement, the output of Maintenance Liquid Pump Sensor does not reach the expected value. |
| Causes: | Maintenance Liquid Pump Motor has a problem. Maintenance Liquid Pump Sensor has a problem. Maintenance Liquid Pump Magnet has dropped out. Wiring or Flexible Cable has short circuitted |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Maintenance Liquid Pump Motor replacement Maintenance Liquid Pump Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0190 |
| Description: | Thermistor under the BED has a problem. |
| Causes: | Device has a problem. Thermistor Cable has short circuited or cutline. |
| Remedy: | Thermistor replacement Check Cable connection Heater Board replacement |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0840 |
| Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
| Causes: | The battery is disconnected from the main PWB Defective main PWB. |
| Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1040 |
| Display: | GL2: W0501 The memory is full. |
| Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1050 |
| Display: | Blue platen switch is dirty. Please clean the switch. |
| Description: | SM lift motor error (side multi tray) After cassette 5 is inserted, SM lift sensor does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor Defective SM lift motor. Defective SM main PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. SM Lift motor 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM Lift motor and SM main PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SM Lift motor. SM Lift sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM Lift sensor and SM main PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the SM Lift sensor. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1800 |
| Description: | Paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| Remedy: | Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1810 |
| Description: | Side multi tray communication error A communication error from side multi tray is detected 10 times in succession. |
| Causes: | Improper installation side multi tray. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. |
| Remedy: | Side multi tray Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). Engine PWB Check the engine software and upgrade to the latest, if necessary. Replace the engine PWB. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1820 |
| Description: | Side paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation side paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. Defective PF main PWB. |
| Remedy: | Side paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and SM main PWB (YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1830 |
| Description: | Paper feeder communication error (third cassette) A communication error from paper feeder is detected 10 times in succession. |
| Remedy: | Paper feeder 3 Check the wiring connection status with PF2, and if necessary, reconnect it. PF3 main PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. PF2 main PWB (YC3 and PF3 main PWB (YC5,4) 2. If the wiring is disconnected, short-circuited or has ground fault, replace the wire. 3. Reinstall the PF firmware. 4. Replace the PF3 main PWB. PF2 main PWB Replace the PF2 main PWB. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1920 |
| Description: | Side paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1930 |
| Description: | Paper feeder 4 EEPROM error When writing the data, the write data and the read data is not in agreement. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | Defective PF main PWB. Replace the PF main PWB. Device damage of EEPROM. Replace the PF main PWB. |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 2010 |
| Display: | Paper loaded askew. Press Load/Eject and reload the paper. |
| Description: | Main motor startup error Main motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Main motor. Engine PWB |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC13) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2200 |
| Description: | Main motor steady-state error After main motor is stabilized, the ready signal is at the H level for 2 s continuously. |
| Causes: | Main motor. Engine PWB. |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2210 |
| Description: | Drum motor steady-state error Stable OFF is detected for 4 s continuously after drum motor stabilized. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and engine PWB (YC4) Defective drive transmission system of the drum motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective drum motor. Replace the drum motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 2330 |
| Description: | Fuser pressure release motor error When the fuser pressure release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and engine PWB (YC38) Defective drive transmission system of the fuser pressure release motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective fuser pressure release motor. Replace the fuser pressure release motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 2340 |
| Description: | Fuser pressure release motor time-out error When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6 s. |
| Causes: | Defective connector cable or poor contact in the connector.Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and engine PWB (YC38) Defective drive transmission system of the fuser pressure release motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective fuser pressure release motor. Replace the fuser pressure release motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2610 |
| Description: | PF paper feed motor error (paper feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 2PF - Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2620 |
| Description: | PF drive motor 3 error (PF3) During the motor drive, the stable signal is not turned on for continuous 5 s. |
| Remedy: | Defective connector cable or poor contact in the connector 1. Reinsert the connector. 2. Check continuity within the connector wire. If none, replace the wire. PF drive motor 3 and PF main PWB (YC6) Drive transmission system for the PF drive motor 1. Check if the rollers and gears rotate smoothly. If not, clean or grease the bushes and gears. 2. Replace the gears, if damaged. PF drive motor Replace the PF drive motor 3. PF main PWB Replace the PF main PWB. |
| Error code: | 2630 |
| Description: | Paper feed motor error (bottom) The notification that was received, the motor clock sensor cannot detect the revolution of the paper feed motor of the optional paper feeder (third). |
| Causes: | Defective paper feeder. Defective engine controller PWB (A0004). |
| Remedy: | Defective paper feeder. Refer to the paper feeder`s service manual. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). |
| Error code: | 3100 |
| Description: | Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor. |
| Causes: | Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective ISC PWB. Defective main PWB. |
| Remedy: | The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary. Scanner motor 1. To check the scanner motor, execute U073. 2. Move the scanner by the hand to check whether it is unusually difficult to move. 3. Check that the optical wire rope is not disengaged and engage the wire. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the scanner motor. Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and ISC PWB (YC8) 3. Replace the home position sensor. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3200 |
| Description: | Exposure lamp error When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LED lamp PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and main PWB (YC11) Defective LED lamp PWB. Replace the LED lamp PWB and check for correct operation. Defective ISC PWB. Replace the ISC PWB and check for correct operation. Defective CCD PWB. Replace the ISU and check for correct operation. Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | 3210 |
| Description: | CIS lamp error When input value at the time of CIS illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Execute CCD of U061 lamp check. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. DP relay PWB Replace the DP relay PWB. |
| Error code: | 3500 |
| Description: | Communication error between scanner and ASIC An error code is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective ISC PWB. Defective main PWB. |
| Remedy: | ISC PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ISC PWB (YC3) and Main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 4000 |
| Display: | Supplies Drum End Soon. |
| Description: | Command Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 4101 |
| Description: | BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 5100 |
| Description: | Short-circuited main charger output Five pages have been printed with the main charger output short-circuited. |
| Causes: | Drum unit installed incorrectly. Engine PWB installed incorrectly. Defective engine PWB |
| Remedy: | Drum unit installed incorrectly. Verify harness is not pinched in the drum unit. Engine PWB installed incorrectly. Verify harness is not pinched in the engine PWB. Defective engine PWB. Replace the engine PWB. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6120 |
| Description: | Abnormally high fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature higher than 190°C/ 374°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 5. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6130 |
| Description: | Broken fuser press thermistor 5 wire The input from the fuser press thermistor 5 has been less than 30°C/ 86°F (A/D: greater thann992) for 60 seconds continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) Fuser IH PWB(YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 7100 |
| Display: | Jam Rear Open the Back Cover and remove the jammed paper, then press [Start]. |
| Description: | Toner sensor error Sensor output value of 8 or less. |
| Causes: | Toner sensor. Toner motor. Main/Engine PWB. |
| Remedy: | Toner sensor 1. Check the toner sensor output by U150. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and main/engine PWB (YC9) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and main/engine PWB (YC12) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. |
| Error code: | 7400 |
| Display: | Jam Tray 2 Pull the paper tray2 completely out of the machine and remove the jammed paper. |
| Description: | Developing unit connector insertion problem Absence of the developing unit is detected. |
| Causes: | Developing unit connector inserted incorrectly. Defective developing unit connector. |
| Remedy: | Developing unit connector inserted incorrectly. Reinsert the developing unit connector if necessary. Defective developing unit connector. Replace the developing unit. |
| Error code: | 7410 |
| Description: | Drum unit connector insertion problem Absence of the drum unit is detected.c |
| Causes: | Drum unit connector inserted incorrectly. Defective drum unit connector. |
| Remedy: | Drum unit connector inserted incorrectly. Reinsert the drum unit connector if necessary. Defective drum unit connector. Replace the drum unit. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 7900 |
| Display: | Jam Manual Feed Pull out the jammed paper from Manual Feed and press Start |
| Description: | Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum unit. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and engine PWB (YC15) Defective drum unit. Replace the drum unit. |
| Error code: | 9200 |
| Description: | DP multi feed sensor communication error A communication error is detected 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DP main PWB (YC1) and ISC PWB (YC12) ISC PWB (YC3) and main PWB (YC11) Defective PWB. Replace the DP main PWB or the ISC PWB and check for correct operation. |
| Error code: | 9220 |
| Description: | DP multi feed sensor backup error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP multi feed sensor. Defective DP main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DP multi feed sensor and DP main PWB (YC11) Defective DP multi feed sensor. Replace the DP multi feed sensor. Defective DP main PWB. Replace the DP main PWB and check for correct operation. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
