Kyocera ECOSYS P5026cdw
Рейтинг
Актуальный
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
50000
Скорость печати
A4
26
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Тип устройства |
Принтер |
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Цветность печати |
цветная |
Телефон |
|
Факс |
|
Сканер |
|
Копир |
|
Печать фотографий |
|
Размещение |
настольный |
Макс. формат |
A4 |
Число страниц в месяц |
50 000 |
Область применения |
средний офис |
Принтер |
|
Количество цветов |
4 |
Время разогрева |
29 |
Макс, ширина отпечатка |
216 |
Макс, длина отпечатка |
356 |
Двусторонняя печать |
|
Прямая печать |
|
Пигментные чернила |
|
Печать без полей |
|
Макс, разрешение для ч/б печати |
|
| По Y | 1 200 |
| По X | 1 200 |
Скорость ч/б печати |
|
| A4 | 26 |
Время выхода первого отпечатка |
|
| Цветн, | 10,5 |
| Ч/б | 9,5 |
Сканер |
|
Слайд-адаптер |
|
Стандарт TWAIN |
|
Стандарт WIA |
|
Отправка изображения по e-mail |
|
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
4 000 |
Ресурс фотобарабана |
100 000 |
Ресурс цветного картриджа/тонера |
3 000 |
Количество картриджей |
4 |
Печать на: |
|
| Этикетках |
|
| Карточках |
|
| Конвертах |
|
| Матовой бумаге |
|
| Глянцевой бумаге |
|
| Пленках |
|
| Рулоне |
|
| CD/DVD |
|
| Фотобумаге |
|
Плотность бумаги |
|
| Минимальная | 60 |
| Максимальная | 220 |
Факс |
|
PC Fax |
|
Цветной |
|
Телефон |
|
Спикерфон |
|
Caller ID |
|
Беспроводная трубка |
|
АОН |
|
Стандарт DECT |
|
Автоответчик |
|
Проводная трубка |
|
Шрифты и языки управления |
|
Языки управления |
|
|
|
|
| PCL 5c |
|
| PostScript 3 |
|
| PCL 6 |
|
| PostScript |
|
| PostScript 2 |
|
Количество установленных шрифтов |
|
| PCL | 93 |
| PostScript | 93 |
Лотки |
|
Емкость лотка ручной подачи |
50 |
Подача бумаги |
|
| Максимальная | 550 |
| Стандартная | 300 |
Вывод бумаги |
|
| Максимальный | 150 |
| Стандартный | 150 |
Финишер |
|
Степлер |
|
Брошюровщик |
|
Сортер |
|
Интерфейсы |
|
Версия USB |
2,0 |
Поддержка iOS |
|
AirPrint |
|
USB |
|
Ethernet (RJ-45) |
|
Wi-Fi |
|
Устройство для чтения карт памяти |
|
RS-232 |
|
FireWire (IEEE 1394) |
|
Bluetooth |
|
LPT |
|
Инфракрасный порт |
|
Поддержка карт памяти |
|
| Secure Digital |
|
Память/Процессор |
|
Частота процессора |
800 |
Макс, объем памяти |
512 |
Объем памяти |
512 |
Дополнительная информация |
|
Экран |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
| Mac OS |
|
| Linux |
|
| Windows |
|
| DOS |
|
Потребляемая мощность |
|
| В режиме ожидания | 33 |
| При работе | 375 |
Уровень шума |
|
| При работе | 47,4 |
Габариты |
|
Высота |
329 |
Ширина |
410 |
Глубина |
410 |
Вес |
21 |
Модули
PAPER FEED
Covers Label
Paper Feed Section 3
FRAME L
DP Covers
Laser Scanner Section
Operation Section
FRAME
ELECTRICAL COMPONENTS
Fuser Section
COVERS
DP Conveying Section
DRIVE SECTION 2
PAPER CASSETTE
DP Drive Section
DP Frame
PANEL
DP Paper Feed Section
SCANNER SECTION
CASSETTE ASSEMBLY
Image Formation Section
Covers 2
Drive Section 1
Paper Feed Section 1
Paper Conveying Section
PAPER FEED SECTION 2
Operation Section 2
DP ASSY SP
Exit Section
Детали DP Conveying Section
| Деталь: | Блок проявки |
| Парткод: | DV-5230C |
| Цена: | 9 200 ₽ |
| Деталь: | Блок проявки |
| Парткод: | DV-5230K |
| Цена: | 9 200 ₽ |
| Деталь: | Блок проявки |
| Парткод: | DV-5230M |
| Цена: | 9 200 ₽ |
| Деталь: | Блок проявки |
| Парткод: | DV-5230Y |
| Цена: | 9 200 ₽ |
| Деталь: | Узел переноса изображения |
| Парткод: | TR-5230 |
| Цена: | 12 900 ₽ |
| Деталь: | EMBLEM |
| Парткод: | 302S018490 |
| Деталь: | EMBLEM MACHINE NUMBER |
| Парткод: | 302RF34100 |
| Деталь: | EMBLEM MACHINE NUMBER |
| Парткод: | 302R734100 |
| Деталь: | EMBLEM MACHINE NUMBER |
| Парткод: | 302R834100 |
| Деталь: | EMBLEM MACHINE NUMBER |
| Парткод: | 302R934100 |
| Деталь: | EMBLEM MACHINE NUMBER |
| Парткод: | 302RA34100 |
| Деталь: | EMBLEM MACHINE NUMBER |
| Парткод: | 302RB34100 |
| Деталь: | EMBLEM MACHINE NUMBER |
| Парткод: | 302RC34100 |
| Деталь: | EMBLEM MACHINE NUMBER |
| Парткод: | 302RD34100 |
| Деталь: | PARTS PULLEY FEED ASSY SP |
| Парткод: | 302R794350 |
| Цена: | 700 ₽ |
| Деталь: | RETARD ROLLER ASSY |
| Парткод: | 302F909171 |
| Цена: | 900 ₽ |
| Деталь: | ROLLER REG REAR |
| Парткод: | 302HN24010 |
| Деталь: | FRAME FEED |
| Парткод: | 302R706010 |
| Деталь: | ACTUATOR REGIST |
| Парткод: | 302R706020 |
| Деталь: | GUIDE PICK HOLDER |
| Парткод: | 302R706100 |
| Деталь: | GEAR SHAFT Z26R |
| Парткод: | 302R706170 |
| Деталь: | GUIDE CASSETTE REAR |
| Парткод: | 302R706180 |
| Деталь: | COVER GUIDE RETARD |
| Парткод: | 302R706200 |
| Деталь: | PARTS HOLDER FEED ASSY SP |
| Парткод: | 302R794070 |
| Деталь: | PARTS HOLDER RETARD ASSY SP |
| Парткод: | 302R794060 |
| Деталь: | PANEL UNIT, MFC9840CDW |
| Парткод: | FK-5230 |
| Цена: | 14 900 ₽ |
| Деталь: | COVER REAR |
| Парткод: | 302S018060 |
| Деталь: | COVER FRONT |
| Парткод: | 302S018050 |
| Деталь: | COVER DP FEED |
| Парткод: | 302R718040 |
| Деталь: | PARTS PLATE ORIGINAL SP |
| Парткод: | 302R794130 |
| Деталь: | ACTUATOR BASE |
| Парткод: | 302S018560 |
| Деталь: | GUIDE READING |
| Парткод: | 302S018120 |
| Деталь: | CONN.CORD ASSY FFC APC |
| Парткод: | 302R746140 |
| Деталь: | LK-5230 |
| Парткод: | 302R793110 |
| Деталь: | PARTS LCD COLOR SP |
| Парткод: | 302K394171 |
| Деталь: | PARTS PWB PANEL ASSY SP |
| Парткод: | 302R794190 |
| Деталь: | PARTS PWB KEY RIGHT ASSY SP |
| Парткод: | 302R794220 |
| Деталь: | CONN.CORD ASSY FFC KEY RIGHT |
| Парткод: | 302R746340 |
| Деталь: | PARTS PWB KEY LEFT ASSY SP |
| Парткод: | 302R794250 |
| Деталь: | LID SHEET COVER T |
| Парткод: | 302S505040 |
| Деталь: | LABEL OPERATION T LEFT EN |
| Парткод: | 302R705710 |
| Деталь: | LABEL OPERATION T LEFT JP |
| Парткод: | 302R705720 |
| Деталь: | SHEET COVER T LEFT |
| Парткод: | 302S505030 |
| Деталь: | LABEL OPERATION T RIGHT EN |
| Парткод: | 302R705510 |
| Деталь: | LABEL OPERATION T RIGHT JP |
| Парткод: | 302R705520 |
| Деталь: | SHEET COVER T RIGHT |
| Парткод: | 302S505020 |
| Деталь: | PARTS OPERATION ASSY SP |
| Парткод: | 302R794050 |
| Деталь: | SHUTTER SECURITY |
| Парткод: | 302R702390 |
| Деталь: | SPRING SHUTTER SECURITY |
| Парткод: | 302R702420 |
| Деталь: | GUIDE CONTAINER K |
| Парткод: | 302R702340 |
| Деталь: | GUIDE CONTAINER Y |
| Парткод: | 302R702310 |
| Деталь: | GUIDE CONTAINER M |
| Парткод: | 302R702320 |
| Деталь: | GUIDE CONTAINER C |
| Парткод: | 302R702330 |
| Деталь: | PARTS PWB ID SENSOR ASSY SP |
| Парткод: | 302R794200 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | PARTS PWB ASSY THERMISTOR SP |
| Парткод: | 302M294130 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | PARTS PWB ERASER ASSY SP |
| Парткод: | 302R794230 |
| Деталь: | PARTS PWB CONTAINER CONNECT ASSY SP |
| Парткод: | 302R794210 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000004+H01 |
| Деталь: | PARTS PWB SWITCH ASSY SP |
| Парткод: | 302R794260 |
| Деталь: | PARTS FAN MOTOR SP |
| Парткод: | 302NG94220 |
| Деталь: | PARTS UNIT LOW VOLTAGE 120V SP |
| Парткод: | 302R794290 |
| Деталь: | PARTS UNIT LOW VOLTAGE 230V SP |
| Парткод: | 302R794300 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302R794270 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302R794280 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302R894010 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302R894020 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302R994030 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302R994040 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302RA94020 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302RA94030 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302RB94030 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302RB94040 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302RC94010 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302RC94020 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302RD94010 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302RD94020 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302RF94010 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302RF94020 |
| Деталь: | PARTS UNIT HIGH VOLTAGE SP |
| Парткод: | 302R794310 |
| Деталь: | PARTS FAX UNIT J SP |
| Парткод: | 302R794330 |
| Деталь: | PARTS FAX UNIT U SP |
| Парткод: | 302R794340 |
| Деталь: | PARTS FAX UNIT E SP |
| Парткод: | 303PA94011 |
| Деталь: | PARTS SPEAKER SP |
| Парткод: | 302R794390 |
| Деталь: | PARTS WIFI UNIT SP |
| Парткод: | 302R794010 |
| Деталь: | FK-5230 |
| Парткод: | 302R793080 |
| Деталь: | FK-5232 |
| Парткод: | 302R793090 |
| Деталь: | FK-5231 |
| Парткод: | 302R793100 |
| Деталь: | COVER SD CARD |
| Парткод: | 302R702180 |
| Деталь: | KEY POWER SW |
| Парткод: | 302R704110 |
| Деталь: | HOLDER MAIN SW |
| Парткод: | 302R704160 |
| Деталь: | SPRING FUSER |
| Парткод: | 302F931270 |
| Деталь: | LABEL CONTAINER OPERATION |
| Парткод: | 302R734050 |
| Деталь: | PUSH BUTTON |
| Парткод: | 302R704130 |
| Деталь: | LOCK CROW |
| Парткод: | 302R704140 |
| Деталь: | COVER TOP FRONT |
| Парткод: | 302RB04010 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302R704090 |
| Деталь: | STOPPER PAPER B |
| Парткод: | 302R704290 |
| Деталь: | Cover Right Rear |
| Парткод: | 302R704040 |
| Деталь: | COVER REAR BOTTOM |
| Парткод: | 302R704240 |
| Деталь: | COVER LEFT REAR HARNESS |
| Парткод: | 302R704170 |
| Деталь: | COVER LEFT |
| Парткод: | 302R704020 |
| Деталь: | COVER LEFT REAR |
| Парткод: | 302R704050 |
| Деталь: | STRAP COVER FRONT R |
| Парткод: | 302R704270 |
| Деталь: | STRAP COVER FRONT L |
| Парткод: | 302R704280 |
| Деталь: | COVER TOP REAR |
| Парткод: | 302RB04020 |
| Деталь: | PARTS PWB P PANEL ASSY SP |
| Парткод: | 302RB94020 |
| Деталь: | KEY QUIET A |
| Парткод: | 302RB05030 |
| Деталь: | KEY QUIET B |
| Парткод: | 302RB05100 |
| Деталь: | INDICATOR |
| Парткод: | 302RB05040 |
| Деталь: | KEY OPERATION JP |
| Парткод: | 302RB05140 |
| Деталь: | KEY OPERATION |
| Парткод: | 302RB05020 |
| Деталь: | PANEL LCD W |
| Парткод: | 302RB05130 |
| Деталь: | PANEL LCD |
| Парткод: | 302RC05010 |
| Деталь: | LABEL QUIET MODE JP |
| Парткод: | 302RB34030 |
| Деталь: | LABEL QUIET MODE EN |
| Парткод: | 302RB34020 |
| Деталь: | LABEL INDICATOR W |
| Парткод: | 302RB34010 |
| Деталь: | LABEL INDICATOR |
| Парткод: | 302RC34010 |
| Деталь: | CONN.CORD ASSY FFC PANEL |
| Парткод: | 302RB46010 |
| Деталь: | PARTS COVER FRONT ASSY SP |
| Парткод: | 302R794020 |
| Деталь: | PARTS RIGHT BOTTOM ASSY SP |
| Парткод: | 302R794030 |
| Деталь: | PARTS COVER CONTAINER ASSY SP |
| Парткод: | 302R794040 |
| Деталь: | ACTUATOR TIMING C |
| Парткод: | 302S018260 |
| Деталь: | GEAR Z30R |
| Парткод: | 302S018370 |
| Деталь: | GEAR Z25L |
| Парткод: | 302S018170 |
| Деталь: | ACTUATOR TIMING A |
| Парткод: | 302S018150 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 302P794010 |
| Деталь: | GUIDE READING |
| Парткод: | 302S018120 |
| Деталь: | ACTUATOR SET |
| Парткод: | 302S018180 |
| Деталь: | COVER PI |
| Парткод: | 302S018690 |
| Деталь: | PARTS SENSOR A4 CIS SP |
| Парткод: | 302R794320 |
| Деталь: | ACTUATOR TIMING B |
| Парткод: | 302S318030 |
| Деталь: | GEAR Z25L |
| Парткод: | 303LL31430 |
| Деталь: | SOLENOID TONER |
| Парткод: | 302GR44150 |
| Цена: | 400 ₽ |
| Деталь: | SOLENOID MPF |
| Парткод: | 302HN44160 |
| Деталь: | LABEL FUSER CAUTION |
| Парткод: | 302R734070 |
| Деталь: | ACTUATOR CASSETTE 1 |
| Парткод: | 302R709100 |
| Деталь: | ACTUATOR CASSETTE 2 |
| Парткод: | 302R709110 |
| Деталь: | CURSOR RIGHT |
| Парткод: | 302R709060 |
| Деталь: | CURSOR LEFT |
| Парткод: | 302R709050 |
| Деталь: | GEAR CASSETTE/A-49 CASSETTE A4 |
| Парткод: | 5MVG127DN071 |
| Деталь: | SPRING BOTTOM |
| Парткод: | 302R709140 |
| Деталь: | CURSOR END |
| Парткод: | 302R709070 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302R709150 |
| Деталь: | CT-5230 |
| Парткод: | 302R793140 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | PARTS MOTOR-PM DP SP |
| Парткод: | 302S094010 |
| Деталь: | PARTS CLUTCH 35 Z35R SP |
| Парткод: | 302NR94010 |
| Деталь: | HINGE LOW |
| Парткод: | 302S018610 |
| Деталь: | HINGE UP |
| Парткод: | 302S018620 |
| Деталь: | STOPPER ORIGINAL |
| Парткод: | 302S018250 |
| Деталь: | Блок лазера |
| Парткод: | LK-5230 |
| Цена: | 4 800 ₽ |
| Деталь: | PULLEY LEADING FEED ADF |
| Парткод: | 36211110 |
| Цена: | 750 ₽ |
| Деталь: | PULLEY,PAPER FEED |
| Парткод: | 3BR07040 |
| Цена: | 420 ₽ |
| Деталь: | PARTS TABLE MAIN ASSY SP |
| Парткод: | 302R794120 |
| Деталь: | COVER TABLE |
| Парткод: | 302S018440 |
| Деталь: | LABEL DP TABLE |
| Парткод: | 302R734090 |
| Деталь: | LABEL DP TABLE |
| Парткод: | 302R934090 |
| Деталь: | PARTS FRAME ISU TOP A ASSY SP |
| Парткод: | 302R794110 |
| Деталь: | PARTS SENSOR A4 CIS SP |
| Парткод: | 302R794320 |
| Деталь: | PARTS MOTOR ISU SP |
| Парткод: | 302R794380 |
| Деталь: | BELT ISU A |
| Парткод: | 302S017340 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 302P794010 |
| Деталь: | CONN.CORD ASSY FFC PANEL |
| Парткод: | 302R746170 |
| Деталь: | CONN.CORD ASSY FFC PANEL |
| Парткод: | 302R946010 |
| Деталь: | CONN.CORD ASSY TABLE MOT |
| Парткод: | 302R746310 |
| Деталь: | Ролик отделения бумаги в держателе, в сборе |
| Парткод: | CET4322 |
| Цена: | 450 ₽ |
| Деталь: | Резина ролика отделения бумаги |
| Парткод: | CET4322PT |
| Цена: | 110 ₽ |
| Деталь: | COVER, PI |
| Парткод: | CT-5230 |
| Цена: | 3 200 ₽ |
| Деталь: | PARTS PWB UNIT CONNECT ASSY SP |
| Парткод: | 302R794240 |
| Деталь: | CONN.CORD ASSY FFC SENSOR TONER |
| Парткод: | 302R746070 |
| Деталь: | CONN.CORD ASSY FFC DRUM |
| Парткод: | 302R746200 |
| Деталь: | TR-5230 |
| Парткод: | 302R793070 |
| Деталь: | DV-5230(K) |
| Парткод: | 302R793030 |
| Деталь: | DV-5230(Y) |
| Парткод: | 302R793040 |
| Деталь: | DV-5230(M) |
| Парткод: | 302R793050 |
| Деталь: | DV-5230(C) |
| Парткод: | 302R793060 |
| Деталь: | DK-5230 |
| Парткод: | 302R793010 |
| Деталь: | DK-5231 |
| Парткод: | 302R793020 |
| Деталь: | KEY POWER SW |
| Парткод: | 302R704110 |
| Деталь: | HOLDER MAIN SW |
| Парткод: | 302R704160 |
| Деталь: | SPRING FUSER |
| Парткод: | 302F931270 |
| Деталь: | LABEL CONTAINER OPERATION |
| Парткод: | 302R734050 |
| Деталь: | PUSH BUTTON |
| Парткод: | 302R704130 |
| Деталь: | LOCK CROW |
| Парткод: | 302R704140 |
| Деталь: | COVER TOP M |
| Парткод: | 302R704060 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302R704090 |
| Деталь: | STOPPER PAPER B |
| Парткод: | 302R704290 |
| Деталь: | Cover Right Rear |
| Парткод: | 302R704040 |
| Деталь: | COVER REAR BOTTOM |
| Парткод: | 302R704240 |
| Деталь: | COVER LEFT REAR HARNESS |
| Парткод: | 302R704170 |
| Деталь: | COVER LEFT |
| Парткод: | 302R704020 |
| Деталь: | COVER LEFT REAR |
| Парткод: | 302R704050 |
| Деталь: | STRAP COVER FRONT R |
| Парткод: | 302R704270 |
| Деталь: | STRAP COVER FRONT L |
| Парткод: | 302R704280 |
| Деталь: | COVER ISU LEFT |
| Парткод: | 302R704070 |
| Деталь: | COVER ISU RIGHT |
| Парткод: | 302R704220 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302R704180 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44210 |
| Деталь: | PARTS COVER FRONT ASSY SP |
| Парткод: | 302R794020 |
| Деталь: | PARTS RIGHT BOTTOM ASSY SP |
| Парткод: | 302R794030 |
| Деталь: | PARTS COVER CONTAINER ASSY SP |
| Парткод: | 302R794040 |
| Деталь: | PARTS MOTOR-BL W40 SP |
| Парткод: | 302LC94283 |
| Деталь: | SOLENOID MPF |
| Парткод: | 302HN44160 |
| Деталь: | PLATE MOTOR MAIN |
| Парткод: | 302R731410 |
| Деталь: | DR-5230 |
| Парткод: | 302R793150 |
| Деталь: | PARTS TRAY MPF UNIT P SP |
| Парткод: | 302RB94010 |
| Деталь: | PARTS TRAY MPF UNIT M SP |
| Парткод: | 302R794100 |
| Деталь: | LABEL MPF |
| Парткод: | 302R734060 |
| Деталь: | PARTS ROLLER REGIST RUBBER SP |
| Парткод: | 302R794360 |
| Деталь: | HOOK CONVEYING L |
| Парткод: | 302R724070 |
| Деталь: | SPRING HOOK CONVEYING L |
| Парткод: | 302R724090 |
| Деталь: | HOOK CONVEYING R |
| Парткод: | 302R724080 |
| Деталь: | SPRING HOOK CONVEYING R |
| Парткод: | 302R724100 |
| Деталь: | PULLEY PA |
| Парткод: | 302HN24400 |
| Деталь: | FRAME CONVEYING B |
| Парткод: | 302R724030 |
| Деталь: | FRAME CONVEYING C |
| Парткод: | 302R724040 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 302R722010 |
| Деталь: | PARTS ROLLER DU SP |
| Парткод: | 302R494410 |
| Деталь: | SPRING PRESS TC L |
| Парткод: | 302R722080 |
| Деталь: | SPRING PRESS TC R |
| Парткод: | 302R722090 |
| Деталь: | SHEET GUIDE MIDDLE L |
| Парткод: | 302R724200 |
| Деталь: | GUIDE MIDDLE |
| Парткод: | 302R724170 |
| Деталь: | LABEL B |
| Парткод: | 302R734030 |
| Деталь: | SPRING PRESS GUIDE MIDDLE |
| Парткод: | 302R724180 |
| Деталь: | PARTS FRAME CONVEYING A ASSY SP |
| Парткод: | 302R794150 |
| Деталь: | PARTS ROLLER TRANSFER ASSY SP |
| Парткод: | 302R794140 |
| Деталь: | PARTS COVER REAR ASSY SP |
| Парткод: | 302R794170 |
| Деталь: | ROLLER M/P ASSY |
| Парткод: | 302HS08260 |
| Цена: | 700 ₽ |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 302P794010 |
| Деталь: | SOLENOID TONER |
| Парткод: | 302GR44150 |
| Цена: | 400 ₽ |
| Деталь: | CONN.CORD ASSY MPF PE |
| Парткод: | 302R746100 |
| Деталь: | PARTS FRAME MPF ASSY SP |
| Парткод: | 302R794080 |
| Деталь: | PARTS GUIDE MPF FEED LOW ASSY SP |
| Парткод: | 302R794090 |
| Деталь: | KEY ONE-TOUCH COLOR |
| Парткод: | 302R705110 |
| Деталь: | PARTS PWB M PANEL ASSY SP |
| Парткод: | 302R994020 |
| Деталь: | LID SHEET COVER LCD |
| Парткод: | 302S005030 |
| Деталь: | SHEET COVER LCD W |
| Парткод: | 302R905020 |
| Деталь: | LABEL OPERATION LCD W EN |
| Парткод: | 302R905510 |
| Деталь: | SHEET COVER LCD |
| Парткод: | 302RA05020 |
| Деталь: | LABEL OPERATION LCD EN |
| Парткод: | 302RA05510 |
| Деталь: | PARTS OPERATION ASSY SP |
| Парткод: | 302R994010 |
| Деталь: | PARTS OPERATION ASSY SP |
| Парткод: | 302RA94010 |
| Деталь: | PARTS DP UNIT SP |
| Парткод: | 302R793130 |
| Деталь: | PARTS DP UNIT SP |
| Парткод: | 302R993130 |
| Деталь: | SOLENOID FD ASSY SP |
| Парткод: | 302HN94140 |
| Цена: | 5 200 ₽ |
| Деталь: | PARTS DRIVE EXIT PRESS ASSY SP |
| Парткод: | 302R794180 |
| Деталь: | COVER CLUTCH |
| Парткод: | 302R731630 |
| Деталь: | SHAFT CLUTCH REGIST |
| Парткод: | 302R731520 |
| Деталь: | GEAR Z28L |
| Парткод: | 302R731510 |
| Деталь: | GEAR Z35R |
| Парткод: | 302R731570 |
| Деталь: | GEAR Z28R |
| Парткод: | 302R731530 |
| Деталь: | SHAFT CLUTCH FEED |
| Парткод: | 302R731540 |
| Деталь: | BUSH DRIVE POM |
| Парткод: | 302LV31480 |
| Деталь: | PARTS CLUTCH 35 Z35R SP |
| Парткод: | 302NR94010 |
| Деталь: | PARTS MOTOR-BL W40 SP |
| Парткод: | 302LC94283 |
| Деталь: | PLATE MOTOR FEED |
| Парткод: | 302R731660 |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 302R794370 |
| Деталь: | BUSH FUSER |
| Парткод: | 302HS25220 |
| Деталь: | GEAR Z19S |
| Парткод: | 302R728110 |
| Деталь: | ACTUATOR FD |
| Парткод: | 302R728180 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44210 |
| Деталь: | PARTS GUIDE EXIT R ASSY SP |
| Парткод: | 302R794160 |
Коды ошибок
0100
0120
0130
0140
0150
0160
0170
0190
0800
0840
0970
1810
2200
2500
4000
4010
4101
4102
4103
4104
4600
4700
6000
6020
6030
6050
6400
6610
7101
7102
7103
7104
7200
7210
7221
7231
7401
7402
7403
7404
7411
7412
7413
7414
7601
7602
7611
7612
7613
7614
7620
7800
7810
7901
7902
7903
7904
7911
7912
7913
7914
9540
F000
F010
F020
F040
F050
F12X
F14X
F15X
F18X
F1DX
F21X, F22X, F23X
F24X
F25X
F26X, F27X, F28X
F29X, F2AX
F2BX, F2CX, F2DX
F2EX, F2FX, F30X
F31X, F32X
F33X
F34X
F35X
F37X
F38X
F3AX, F3BX, F3CX
F3DX, F3EX, F3FX
F40X, F41X, F42X
F43X, F44X, F45X
F46X
F47X, F48X
F4DX, F4EX
F4FX
F50X
F51X, F52X, F53X
F55X, F56X, F57X
F58X, F59X, F5AX
F5BX, F5CX
F5DX, F5EX
F5FX
F62X
F63X
Описание
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0130 |
| Description: | There is a problem with Thermistor for Print Heater. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0140 |
| Description: | There is a problem with Thermistor for dryer. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0190 |
| Description: | Thermistor under the BED has a problem. |
| Causes: | Device has a problem. Thermistor Cable has short circuited or cutline. |
| Remedy: | Thermistor replacement Check Cable connection Heater Board replacement |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0840 |
| Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
| Causes: | The battery is disconnected from the main PWB Defective main PWB. |
| Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
| Error code: | 0970 |
| Description: | 12 V power down detect Power is disconnected during sleeping. |
| Causes: | Defective power source PWB. |
| Remedy: | Replace the power source PWB and check for correct operation. |
| Error code: | 1810 |
| Description: | Side multi tray communication error A communication error from side multi tray is detected 10 times in succession. |
| Causes: | Improper installation side multi tray. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. |
| Remedy: | Side multi tray Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). Engine PWB Check the engine software and upgrade to the latest, if necessary. Replace the engine PWB. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2200 |
| Description: | Main motor steady-state error After main motor is stabilized, the ready signal is at the H level for 2 s continuously. |
| Causes: | Main motor. Engine PWB. |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4000 |
| Display: | Supplies Drum End Soon. |
| Description: | Command Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 4010 |
| Description: | Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and engine PWB (YC11) Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 4101 |
| Description: | BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4102 |
| Description: | BD initialization error C After polygon motor C is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB C. Defective engine PWB. |
| Remedy: | PD PWB C (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4103 |
| Description: | BD initialization error M After polygon motor M is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB M. Defective engine PWB. |
| Remedy: | PD PWB M (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4104 |
| Description: | BD initialization error Y After polygon motor Y is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB Y. Defective engine PWB. |
| Remedy: | PD PWB Y (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4600 |
| Display: | Maintenance Replace Laser |
| Description: | LSU cleaning motor error After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s. After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective LSU cleaning motor. Defective engine PWB. |
| Remedy: | LSU cleaning motor 1. Execute LSU cleaning using Adjustment/Maintenance of the system menu. 2. Rotate the drive gear and the cleaning spiral by the hand and check that they are not unusually loaded, and replace if it is damaged. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LSU cleaning motor and Engine PWB (YC21) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the LSU cleaning motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4700 |
| Display: | Supplies WT Box End Soon |
| Description: | VIDEO_ASIC device error Communication with the video ASIC has failed 5 times successively. After writing to the VIDEO ASIC, the error that the reading value from the same address does not match occurs 8 times successively. |
| Causes: | Engine PWB. Main PWB |
| Remedy: | Main PWB 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Check that the connectors on the main PWB are properly connected, and if not, re-connect them. 3. Replace the main PWB. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6050 |
| Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
| Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 6610 |
| Description: | Fuser release sensor error When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser release motor. Defective engine PWB. |
| Remedy: | Fuser release motor 1. To check the motor operation, execute U030 Fuser Release. 2. Check that the drive gear can be rotated and the separation is possible. 3. If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Fuser unit. Fuser release sensor 1. Check that the sensor is correctly positioned. 2. Check that the sensor is not contaminated or damaged. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7101 |
| Description: | Toner sensor error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7102 |
| Description: | Toner sensor C error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor C 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit C are not damaged and the spiral can rotate. 5. Replace the Developer unit C. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7103 |
| Description: | Toner sensor M error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor M 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit M are not damaged and the spiral can rotate. 5. Replace the Developer unit M. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7104 |
| Description: | Toner sensor Y error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor Y 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit Y are not damaged and the spiral can rotate. 5. Replace the Developer unit Y. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7200 |
| Display: | Jam MP Tray Remove the jammed paper from MP Tray and press [Retry]. |
| Description: | Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7210 |
| Description: | Short-circuited outer temperature sensor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7221 |
| Description: | Broken LSU thermistor wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LSU thermistor. Defective engine PWB. |
| Remedy: | LSU thermistor 1. Confirm LSU is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the laser scanner unit. LSU relay PWB REPLACE the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7231 |
| Description: | Short-circuited LSU thermistor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LSU thermistor. Defective engine PWB. |
| Remedy: | LSU thermistor 1. Confirm LSU is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the laser scanner unit. LSU relay PWB Replace the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7401 |
| Description: | Developer unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Different type of the developer unit is installed. Install the developer unit of the correct type. Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7402 |
| Description: | Developer unit C type mismatch error Absence of the developer unit C is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit C and front PWB (YC13) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7403 |
| Description: | Developer unit M type mismatch error Absence of the developer unit M is detected. |
| Causes: | Defective connector cable or poor contact in the connector Different type of the developer unit is installed |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit M and front PWB (YC11) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7404 |
| Description: | Developer unit Y type mismatch error Absence of the developer unit Y is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit Y and front PWB (YC15) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7411 |
| Description: | Drum unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the drum unit is installed. |
| Remedy: | Different type of the drum unit is installed. Install the drum unit of the correct type. Drum unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum unit and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7412 |
| Description: | Drum unit type Mismatch error (Cyan) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit C |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7413 |
| Description: | Drum unit type Mismatch error (Magenta) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit M |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7414 |
| Description: | Drum unit type Mismatch error (Yellow) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit Y |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7601 |
| Description: | ID sensor 1 error [Front] Dark potential error FrontDarkP and FrontDarkS are greater than 0.80V. Light potential error FrontBrightS is smaller than FrontDarkS. FrontBrightP is smaller than [FrontDarkP + 0.5V]. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | ID sensor1 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor 1 (front) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7602 |
| Description: | ID sensor 2 error [Rear] Dark potential error RearDarkP and RearDarkS are greater than 0.80V. Light potential error RearBrightS is smaller than RearDarkS. RearBrightP is smaller than [RearDarkP + 0.5V]. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | ID sensor 2 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor2 (rear) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7611 |
| Description: | Bias calibration reading value error (Black) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7612 |
| Description: | Bias calibration reading value error (Cyan) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7613 |
| Description: | Bias calibration reading value error (Magenta) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7614 |
| Description: | Bias calibration reading value error (Yellow) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7620 |
| Description: | Color Registration timing of detection Color patches printed on the primary transfer belt are not within the ID sensor readable range. Or the poor density occurs. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor LSU 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. 8. When checking the printing position of the color, if any color shift occurs, re-install the LSU and the drum unit. 9. If not corrected, replace the LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 7901 |
| Description: | Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB. |
| Remedy: | DR PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7902 |
| Description: | Drum C EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB C. |
| Remedy: | DR PWB- C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB- C and Front PWB (YC12) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit C. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7903 |
| Description: | Drum M EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB M. |
| Remedy: | DR PWB- M 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB- M and Front PWB (YC10) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit M. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7904 |
| Description: | Drum Y EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB Y. |
| Remedy: | DRPWB- Y 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DRPWB- Y and Front PWB (YC14) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit Y. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7911 |
| Description: | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit. |
| Remedy: | Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7912 |
| Description: | Developer unit C EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit C. |
| Remedy: | Developer unit C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit C. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7913 |
| Description: | Developer unit M EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit M. |
| Remedy: | Developer unit M 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit M. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7914 |
| Description: | Developer unit Y EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit Y. |
| Remedy: | Developer unit Y 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit Y. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 9540 |
| Description: | Backup data error The machine may not be recovered or may have trouble in its function with changes of the internal data when replacing some the parts at the same time. |
| Causes: | PWBs |
| Remedy: | Reattach the parts below in case of replacing 2 or more of them at the same time. Affected parts : Memory, PWBs * Do not replace two or more of the parts at the same time. * And, do not either execute the following works when replacing the above parts. Replace the drum unit or the developing unit. Replace the drum unit for the one color with another in the same machine. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F12X |
| Description: | An error is detected at the Scan control section |
| Remedy: | 1) Check connection of the harness (Scan/DP - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the Scan/DP board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F14X |
| Description: | An error is detected at the FAX control section |
| Remedy: | 1) Check connection of the harness (FAX - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check function. (Take cae of the received data since it is cleared) 5) Replace the FAX_DIMM and check function. 6) Replace the FAX board and check function. 7) Replace the main board and check function. 8) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F15X |
| Description: | An error is detected at the authentication device control section |
| Remedy: | 1) Check connection of the harness (Authentication device - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F18X |
| Description: | An error is detected at the Video control secion |
| Remedy: | 1) Check connection of the harness (Engine - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the engine board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F1DX |
| Description: | An error is detected at the Image memory management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. *The F1D4 error is RAM allocation error. -1Check it with the U340 -2Initialize the setting valued with the U021 |
| Error code: | F21X, F22X, F23X |
| Description: | An error is detected at the Image processing section |
| Remedy: | 1) Check contact of the DDR memory and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F24X |
| Description: | An error is detected at the System management section |
| Remedy: | 1) Check contact of the DDR memory and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F25X |
| Description: | An error is detected at the Network management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Retrieve the USBLOG and contact the Service Administratuve Division. (or retrieve the packet capture data depending on the reult of analysis) |
| Error code: | F26X, F27X, F28X |
| Description: | Abnormality detecting in the system Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F29X, F2AX |
| Description: | Abnormality detecting in the system Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F2BX, F2CX, F2DX |
| Description: | Abnormality detecting in a network control part |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters. (Depending on an analysis result, it is packet capture acquisition) * Only HDD standard model |
| Error code: | F2EX, F2FX, F30X |
| Description: | Abnormality detecting in a network control part |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters. (Depending on an analysis result, it is packet capture acquisition) * Only HDD standard model |
| Error code: | F31X, F32X |
| Description: | Abnormality detecting in a network control part |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters. (Depending on an analysis result, it is packet capture acquisition) * Only HDD standard model |
| Error code: | F33X |
| Description: | An error is detected at the Scan management section |
| Remedy: | 1) Check connection of the harness (Scan/DP board - main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the Scan/DP board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F34X |
| Description: | An error is detected at the Panel management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F35X |
| Description: | An error is detected at the Print control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F37X |
| Description: | An error is detected at the FAX management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check function. (Take cae of the received data since it is cleared) 4) Replace the FAX_DIMM and check function. 5) Replace the main board and check function. 6) Replace the HDD and check function. 7) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F38X |
| Description: | An error is detected at the Authentication/permit management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F3AX, F3BX, F3CX |
| Description: | Abnormality detecting in the Entity Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F3DX, F3EX, F3FX |
| Description: | Abnormality detecting in the Entity Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F40X, F41X, F42X |
| Description: | Abnormality detecting in the Entity Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F43X, F44X, F45X |
| Description: | Abnormality detecting in the Entity Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F46X |
| Description: | An error is detected at the Print image process section |
| Remedy: | 1) Replace the main board and check function. 2) Retrieve the USBLOG (or retrieve the print capture data by case) |
| Error code: | F47X, F48X |
| Description: | Abnormality detecting of an image editing processing part |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F4DX, F4EX |
| Description: | An error is detected at the Entity control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F4FX |
| Description: | An error is detected at the Job control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F50X |
| Description: | An error is detected at the FAX control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F51X, F52X, F53X |
| Description: | Abnormality detecting in a JOB execution part |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F55X, F56X, F57X |
| Description: | Abnormality detecting in a JOB execution part |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F58X, F59X, F5AX |
| Description: | Abnormality detecting in the various-services Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F5BX, F5CX |
| Description: | Abnormality detecting in the various-services Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F5DX, F5EX |
| Description: | Abnormality detecting in the various-services Management Department |
| Remedy: | (1) Initialize HDD and perform an operation check. (FULL of U024) * ( 2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Exchange HDD and perform an operation check. * (5) Get USBLOG and contact service headquarters. * Only HDD standard model |
| Error code: | F5FX |
| Description: | An error is detected at the Service execution section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F62X |
| Description: | An error is detected at the Service execution section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F63X |
| Description: | An error is detected at the Device control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Парткод
Название
Kyocera Блок фотобарабана черный
Kyocera Блок фотобарабана цветной
Kyocera Блок проявки голубой
Kyocera Блок проявки черный
Kyocera Блок проявки пурпурный
Kyocera Блок проявки желтый
Kyocera Узел термозакрепления
Kyocera Тонер-картридж голубой
Kyocera Тонер-картридж черный
Kyocera Тонер-картридж пурпурный
Kyocera Тонер-картридж желтый
