Kyocera FS-1900

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

65000

Цветность печати

черно-белая

Общие характеристики
Копир
Сканер
Печать фотографий
Цветность печати
Область применения	средний офис
Макс. формат	A4
Тип устройства	Принтер
Число страниц в месяц	65 000
Технология печати	лазерная
Тип	лазерный/светодиодный
Принтер
Двусторонняя печать
Прямая печать
Макс, разрешение для ч/б печати
По Y	600
По X	1 800
Расходные материалы
Ресурс ч/б картриджа/тонера	10 000
Печать на:
Этикетках
Пленках
Фотобумаге
Языки управления
PostScript
Лотки
Подача бумаги
Стандартная	600
Вывод бумаги
Стандартный	250
Интерфейсы
Ethernet (RJ-45)
Инфракрасный порт
LPT
USB
Память/Процессор
Макс, объем памяти	16
Объем памяти	16
Дополнительная информация
Поддержка ОС
Linux
Mac OS
DOS
Windows
Уровень шума
При работе	53
Габариты
Вес	13
Высота	300
Глубина	390
Ширина	345

Модули

FRAME L

CASSETTE ASSEMBLY

Детали CASSETTE ASSEMBLY

Деталь:	Ролик подачи бумаги
Парткод:	5AAVR0LL+047
Цена:	1 000 ₽

$kyocera\5AAVR0LL+048.jpg$

Деталь:	Ролик захвата бумаги
Парткод:	5AAVR0LL+048
Цена:	1 000 ₽

$kyocera\5AAVR0LL+051.jpg$

Деталь:	Ролик захвата бумаги из лотка ручной подачи
Парткод:	5AAVR0LL+051
Цена:	800 ₽

Деталь:	Узел захвата в сборе
Парткод:	5AAYA37E++35
Цена:	6 700 ₽

Коды ошибок

0420

0440

0460

1210

2000

2600

2610

2620

2630

4000

4200

5300

6000

6020

6400

7001

7350

8010

F010

F020

F030

F040

F070

Описание

Парткод

Название

Kyocera Блок фотобарабана

Kyocera Блок проявки

Kyocera Узел термозакрепления

Kyocera Главный коротрон

Kyocera Сервисный комплект

Kyocera Тонер-картридж черный

Error code:	0420
Description:	Paper feeder communication error Communication error between control PWB and optional paper feeder.
Causes:	Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF main-PWB.
Remedy:	Improper installation paper feeder. Follow installation instruction carefully again. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective control PWB. Replace the control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder). Defective PF main- PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Error code:	0440
Description:	Communication error between printer and document finisher/ mailbox sorter • The CPU (U2) of engine controller PWB (KP-992) does not communicate with the DF-31 document finisher/SO-30 mailbox sorter normally. • The ASIC (U8) of engine controller PWB (KP-992) does not communicate to the DF-31 document finisher/SO-30 mailbox sorter normally.
Causes:	Defective engine controller PWB (KP-992). Defective main PWB of DF-31 document finisher/SO-30 mailbox sorter. Defective paper feeder/options relay PWB (KP-995). Defective signal cable between printer and DF-31 document finisher/ SO-30 mailbox sorter. Defective harness (2CK2719) between engine controller PWB (KP-992) and paper feeder/options relay PWB (KP- 995), or poor contact of the connector terminals. Defective document finisher interface PWB. Defective harness (2CK2727) between document finisher interface PWB and engine controller PWB (KP- 992), or poor contact of the connector terminals.
Remedy:	Replace the engine controller PWB (KP- 992). Replace the main PWB of DF-31 document finisher/SO-30 mailbox sorter. See DF-31 document finisher/SO-30 mailbox sorter’s service manual. Replace the paper feeder/options relay PWB (KP-995). Replace the signal cable between printer and DF-31 document finisher/SO-30 mailbox sorter. Check the continuity of the harness (2CK2719). Check the insertion of connectors. Replace the document finisher interface PWB. Check the continuity of the harness (2CK2727). Check the insertion of connectors.

Error code:	0460
Description:	Communication error between printer and duplex unit • The CPU (U2) of engine controller PWB (KP-992) does not communicate with the PD-800 duplex unit normally.
Causes:	Defective engine controller PWB (KP-992). Defective main board of PD-800 duplex unit. Defective paper feeder/options relay PWB (KP- 995). Defective connection printer and PD-800 duplex unit. Defective harness (2CK2719) between engine controller PWB (KP-992) and paper feeder/ options relay PWB (KP-995), or poor contact of the connector terminals.
Remedy:	Replace the engine controller PWB (KP- 992). Replace the main board of duplex unit PD- 30. See PD-800 duplex unit’s service manual. Replace the paper feeder/options relay PWB (KP-995). Reinstall PD-800 duplex unit. Check the continuity of the harness (2CK2719). Check the insertion of connectors.

Error code:	1210
Description:	Mode Select An invalid print mode was selected in the print command.
Causes:	Defective side registration home position sensor. Defective side registration motor. Defective engine controller PWB (KP-992).
Remedy:	Resend the print job. If the problem remains, then reinstall the printer driver. Service: Resend the print job. If the problem remains, then reinstall the print driver.

Error code:	2000
Description:	DDA Communication Error.
Causes:	The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error.
Remedy:	Replace the Main Board.

Деталь:	Шестерня тефлонового вала
Парткод:	5MVG148XN010
Цена:	900 ₽

Error code:	4000
Display:	Supplies Drum End Soon.
Description:	Command Communication Error.
Causes:	The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error.
Remedy:	Replace the Main Board.

Error code:	F0
Display:	SVC F0 ERROR
Description:	The communication ended because of a WDT due to an overrun of the software.
Causes:	Defective main controller PWB. Defective operator panel PWB. Defective mainengine controllers relay PWB. Defective engine controller PWB . Defective harness between engine controller PWB and operator panel PWB, or poor contact of the connector terminals.
Remedy:	Attempt the communication again. If the error occurs frequently, perform a memory clear (except user area.)

Error code:	6000
Description:	Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F.
Causes:	Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB.
Remedy:	Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit.

Error code:	6020
Description:	Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s.
Causes:	Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB.
Remedy:	Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Error code:	6400
Display:	No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit.
Description:	Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s.
Causes:	Fuser unit.
Remedy:	Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB.

Error code:	7001
Description:	Toner motor error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets.
Causes:	Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB.
Remedy:	Toner container 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.

Kyocera FS-1900

Общие характеристики

Копир

Сканер

Печать фотографий

Цветность печати

Область применения

Макс. формат

Тип устройства

Число страниц в месяц

Технология печати

Тип

Принтер

Двусторонняя печать

Прямая печать

Макс, разрешение для ч/б печати

Расходные материалы

Ресурс ч/б картриджа/тонера

Печать на:

Языки управления

Лотки

Подача бумаги

Вывод бумаги

Интерфейсы

Ethernet (RJ-45)

Инфракрасный порт

LPT

USB

Память/Процессор

Макс, объем памяти

Объем памяти

Дополнительная информация

Поддержка ОС

Уровень шума

Габариты

Вес

Высота

Глубина

Ширина

Модули

Детали CASSETTE ASSEMBLY

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку