Kyocera FS-9530DN
Рейтинг
Актуальный
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
300000
Скорость печати
A4
51
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Размещение |
настольный |
Тип устройства |
Принтер |
Телефон |
|
Печать фотографий |
|
Сканер |
|
Факс |
|
Копир |
|
Число страниц в месяц |
300 000 |
Тип |
лазерный/светодиодный |
Макс. формат |
A3 |
Цветность печати |
|
Технология печати |
лазерная |
Область применения |
большой офис |
Принтер |
|
Время разогрева |
60 |
Пигментные чернила |
|
Печать без полей |
|
Прямая печать |
|
Двусторонняя печать |
|
Макс, разрешение для ч/б печати |
|
| По X | 600 |
| По Y | 1 800 |
Скорость ч/б печати |
|
| A3 | 26 |
| A4 | 51 |
Время выхода первого отпечатка |
|
| Ч/б | 3,5 |
Сканер |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Слайд-адаптер |
|
Стандарт WIA |
|
Расходные материалы |
|
Ресурс фотобарабана |
500 000 |
Ресурс ч/б картриджа/тонера |
40 000 |
Количество картриджей |
1 |
Печать на: |
|
| Карточках |
|
| Глянцевой бумаге |
|
| Конвертах |
|
| Матовой бумаге |
|
| Этикетках |
|
| CD/DVD |
|
| Рулоне |
|
| Фотобумаге |
|
| Пленках |
|
Плотность бумаги |
|
| Максимальная | 200 |
| Минимальная | 45 |
Факс |
|
Цветной |
|
Телефон |
|
Caller ID |
|
Спикерфон |
|
Проводная трубка |
|
Беспроводная трубка |
|
АОН |
|
Стандарт DECT |
|
Автоответчик |
|
Шрифты и языки управления |
|
Языки управления |
|
| PCL 5e |
|
| PostScript 3 |
|
| PostScript |
|
|
|
|
| PCL 6 |
|
| PCL 5c |
|
| PPDS |
|
| PostScript 2 |
|
Количество установленных шрифтов |
|
| PostScript | 136 |
| PCL | 80 |
Лотки |
|
Подача бумаги |
|
| Максимальная | 4 200 |
| Стандартная | 1 200 |
Вывод бумаги |
|
| Стандартный | 500 |
Интерфейсы |
|
Количество свободных слотов расширения |
1 |
Версия USB |
2,0 |
RS-232 |
|
Wi-Fi |
|
FireWire (IEEE 1394) |
|
Инфракрасный порт |
|
Bluetooth |
|
USB |
|
Ethernet (RJ-45) |
|
LPT |
|
Устройство для чтения карт памяти |
|
Поддержка карт памяти |
|
| CompactFlash |
|
Память/Процессор |
|
Макс, объем памяти |
640 |
Объем памяти |
128 |
Частота процессора |
600 |
Процессор |
Power PC 750FL |
Дополнительная информация |
|
Экран |
|
Мин. системные требования |
|
Поддержка ОС |
|
| Mac OS |
|
| Windows |
|
| Linux |
|
| DOS |
|
Потребляемая мощность |
|
| При работе | 900 |
| В режиме ожидания | 180 |
Уровень шума |
|
| В режиме ожидания | 37 |
| При работе | 51 |
Габариты |
|
Вес |
68 |
Высота |
615 |
Ширина |
599 |
Глубина |
646 |
Модули
LSU
Electrical Components I
Paper Feed-In III
Bypass feed unit
Bypass unit
Paper exit
Paper Feed-In II
FRAME L
PANEL
Paper Feed-In I
Drive Unit I
FUSER UNIT
Drum Unit
CASSETTE
DUPLEX
COVERS
FRAMES
CASSETTE ASSEMBLY
Electrical Components II
Developer unit
Drive Unit II
Paper Conveying
PAPER FEED
COVERS and LABELS
Детали Paper exit
| Деталь: | LK-710 |
| Парткод: | 302GR93090 |
| Деталь: | FRONT MOUNT HOUSING |
| Парткод: | 2BL13120 |
| Деталь: | PIN LSU FIXING |
| Парткод: | 302GR02830 |
| Деталь: | SPRING FIX LSU |
| Парткод: | 2BL13290 |
| Деталь: | FRONT ADJUSTING LSU |
| Парткод: | 2BL13070 |
| Деталь: | REAR ADJUSTING LSU |
| Парткод: | 2BL13060 |
| Деталь: | ADJUSTING PLT LSU |
| Парткод: | 2BL13250 |
| Деталь: | WIRE LSU |
| Парткод: | 302G146010 |
| Деталь: | MOUNT FAN |
| Парткод: | 2BL02230 |
| Деталь: | PARTS,FAN LSU 60-25 SP |
| Парткод: | 302GR94250 |
| Деталь: | ASSCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SPONGE FAN |
| Парткод: | 2BL02240 |
| Деталь: | PARTS FILTER DUST F1 ASSY |
| Парткод: | 302GR94430 |
| Деталь: | PARTS FILTER DUST F2 ASSY |
| Парткод: | 302GR94440 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 2BM27890 |
| Деталь: | EDGING,EDS-17L(KITAGAWA) |
| Парткод: | M2104250 |
| Деталь: | COVER CONN |
| Парткод: | 302GR39190 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | WIRE BYPASS FEED PI |
| Парткод: | 302GR46300 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H02 |
| Деталь: | RETAINING PIN,DRAWER |
| Парткод: | 3033927451 |
| Деталь: | MOUNT DRUM DRAWER |
| Парткод: | 2BL26200 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC10B1112+H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ASSCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510009++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | WIRE PAPER FEED(P) |
| Парткод: | 302G146090 |
| Деталь: | MOUNT,CASSETTE SWITCH |
| Парткод: | 302FG07050 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | CLAMP, CKN-07(KITAGAWA) |
| Парткод: | M2105910 |
| Деталь: | MOUNT POWER PWB |
| Парткод: | 302GR39081 |
| Деталь: | UNIT LOW VOLTAGE 100 |
| Парткод: | 302G145010 |
| Деталь: | UNIT LOW VOLTAGE 200 |
| Парткод: | 302G145020 |
| Деталь: | SHIELD SUBWIRE |
| Парткод: | 2BJ26210 |
| Деталь: | MOUNT OPTION I/F |
| Парткод: | 302GR39090 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | WIRE FINISHER SOCKET |
| Парткод: | 302GR46160 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | WIRE OPE INNER |
| Парткод: | 302G146050 |
| Деталь: | WIRE OPE REAR |
| Парткод: | 302G146080 |
| Деталь: | MOUNT, DECK CONNECTOR |
| Парткод: | 2AR26340 |
| Деталь: | SW. SEESAW |
| Парткод: | 7SC010101+++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | EDGING, EDS-25L(KITAGAWA) |
| Парткод: | M2104280 |
| Деталь: | MOUNT FIXING DRAWER |
| Парткод: | 2BL26290 |
| Деталь: | WIRE DRAWER(P) |
| Парткод: | 302G146140 |
| Деталь: | WIRE PRIMARY(P) |
| Парткод: | 302G146150 |
| Деталь: | PIN TERMINAL |
| Парткод: | 302BL26061 |
| Деталь: | SPRING TERMINAL |
| Парткод: | 2BL26070 |
| Деталь: | SPRING TERMINAL T |
| Парткод: | 2BL26270 |
| Деталь: | CASE HIGH VOLTAGE |
| Парткод: | 302BL26051 |
| Деталь: | GROUND PLATE HV |
| Парткод: | 2BL26080 |
| Деталь: | HVU |
| Парткод: | 302GR45031 |
| Деталь: | WIRE HIGH VOLTAGE(P) |
| Парткод: | 302G146130 |
| Деталь: | WIRE MOTOR(P) |
| Парткод: | 302G146100 |
| Деталь: | WIRE FRONT(P) |
| Парткод: | 302G146120 |
| Деталь: | EDGING,EDS-2 |
| Парткод: | M2104210 |
| Деталь: | LEFT MOUNT I/L |
| Парткод: | 2BL26110 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | SWITCH,INTERLOCK |
| Парткод: | 2AR27040 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | LEFT WORK PLATE I/L |
| Парткод: | 2BL26120 |
| Деталь: | SHAFT I/L |
| Парткод: | 302BL26281 |
| Деталь: | WIRE SADDLE,YMC-15-0(KITAGAWA) |
| Парткод: | M2109350 |
| Деталь: | FRONT MOUNT COVER |
| Парткод: | 2BL04060 |
| Деталь: | INNER LEFT COVER |
| Парткод: | 302GR04330 |
| Деталь: | TONER DETECTION ASSY |
| Парткод: | 302GR01190 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC05B1106+H01 |
| Деталь: | WIRE TONER DISPOSAL |
| Парткод: | 302GR46290 |
| Деталь: | SPACER WIRE |
| Парткод: | 2BL04460 |
| Деталь: | GROUND PLATE INNER L |
| Парткод: | 2BL04450 |
| Деталь: | MOUNT INLET A |
| Парткод: | 302FG26102 |
| Деталь: | MOUNT INLET B |
| Парткод: | 302G139100 |
| Деталь: | INLET ASSY |
| Парткод: | 302GR01240 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBCP8P8E001H01 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | MOUNT MAIN SW |
| Парткод: | 302GR39120 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | POWER CODE AS(240) |
| Парткод: | 3029927232 |
| Деталь: | SHIELD 10X8X20,GASKET |
| Парткод: | 2AC26310 |
| Деталь: | LEVER L COVER LOCK M |
| Парткод: | 2BL04550 |
| Деталь: | SPRING L COVER LOCK |
| Парткод: | 2BL04560 |
| Деталь: | LEVER COVER RELEASE |
| Парткод: | 2BL04600 |
| Деталь: | FRONT PLATE EXIT L |
| Парткод: | 2BL04660 |
| Деталь: | REAR PLATE EXIT L |
| Парткод: | 2BL04670 |
| Деталь: | STRAP COVER |
| Парткод: | 2BL04680 |
| Деталь: | GROUND PLATE LEFT B |
| Парткод: | 2BL04700 |
| Деталь: | FILM WIRE PROTECT |
| Парткод: | 2BL21460 |
| Деталь: | GUIDE FILM DU |
| Парткод: | 2BL21490 |
| Деталь: | FILM WIRE PROTECT B |
| Парткод: | 2BL21500 |
| Деталь: | GROUND PLATE LEFT FAN |
| Парткод: | 2BL23110 |
| Деталь: | SPONGE LEFT FAN |
| Парткод: | 2BL23170 |
| Деталь: | LEFT COVER MIDDLE |
| Парткод: | 302BL04512 |
| Деталь: | SHAFT L COVER LOCK M |
| Парткод: | 302BL04541 |
| Деталь: | PLATE LEFT COVER M |
| Парткод: | 302BL04621 |
| Деталь: | COVER EXIT L |
| Парткод: | 302BL04651 |
| Деталь: | LABEL VFEED CAUTION |
| Парткод: | 302FB05380 |
| Деталь: | LABEL VFEED CAUTION 6NATIONS |
| Парткод: | 302FB05440 |
| Деталь: | MOUNT OZONE FILTER A |
| Парткод: | 302FG23021 |
| Деталь: | FILTER OZONE A |
| Парткод: | 302FG23030 |
| Деталь: | PIN LEFT COVER |
| Парткод: | 302GR02810 |
| Деталь: | SEAL PROTECT OZONE |
| Парткод: | 302GR04460 |
| Деталь: | GUIDE LEFT COVER M |
| Парткод: | 302GR28050 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | 302GR34150 |
| Деталь: | WIRE CONVEYING FAN |
| Парткод: | 302GR46310 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | MOUNT REAR GUIDE |
| Парткод: | 2BL20091 |
| Деталь: | REAR GUIDE FIXING |
| Парткод: | 2BL20100 |
| Деталь: | CLAW PRESS ROLLER |
| Парткод: | 2BL20350 |
| Деталь: | GUIDE EXIT L |
| Парткод: | 2BL21290 |
| Деталь: | PULLEY FEED SHIFT |
| Парткод: | 2BL21330 |
| Деталь: | SPRING CHANGE PULLEY |
| Парткод: | 2BL21340 |
| Деталь: | SHAFT,PRESSURE ROLLER SEPARATION CLAW |
| Парткод: | 302AR20511 |
| Деталь: | SHAFT CHANGE PULLEY |
| Парткод: | 302BL21362 |
| Деталь: | PIN REAR GUIDE FIXING |
| Парткод: | 302GR02840 |
| Деталь: | SPRING CLAW PRESS |
| Парткод: | 302GR25350 |
| Деталь: | GUIDE FEED SHIFT L |
| Парткод: | 302GR28040 |
| Деталь: | SPRING,DEVELOPING ROCK |
| Парткод: | 65009050 |
| Деталь: | PARTS,FAN DU 60-15 |
| Парткод: | 302GR94340 |
| Деталь: | STRAP RELEASE |
| Парткод: | 2BL06960 |
| Деталь: | LABEL LEFT COVER A |
| Парткод: | 302GR34040 |
| Деталь: | LEFT COVER FEED |
| Парткод: | 302BL06101 |
| Деталь: | SPRING FEED |
| Парткод: | 2BL06340 |
| Деталь: | SHAFT FEED PULLEY |
| Парткод: | 302BL06212 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL16080 |
| Деталь: | SHAFT CAM |
| Парткод: | 302BL14231 |
| Деталь: | BUSH POM/F0093A4 |
| Парткод: | 5MVM122DB003 |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | RETAINING PIN,VERTICAL CONVEYING |
| Парткод: | 302AR07541 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | CAM DLP |
| Парткод: | 2BL14240 |
| Деталь: | SPRING CAM |
| Парткод: | 2BL14410 |
| Деталь: | MOUNT CAM |
| Парткод: | 302BL14141 |
| Деталь: | PARTS LEFT COVER MIDDLE ASSY |
| Парткод: | 302G193080 |
| Деталь: | PARTS REAR GUIDE FUSER UNIT |
| Парткод: | 302GR93180 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | UPPERGUIDE BYPASS |
| Парткод: | 2BL06520 |
| Деталь: | MOUNT RAIL |
| Парткод: | 2BL06570 |
| Деталь: | RAIL BYPASS |
| Парткод: | 2BL06580 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BL06590 |
| Деталь: | ACTUATOR BYPASSFEED |
| Парткод: | 2BL06730 |
| Деталь: | SPRING BYPASSFEED |
| Парткод: | 2BL06780 |
| Деталь: | GROUNDPLATE BYPASS |
| Парткод: | 2BL06790 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL06800 |
| Деталь: | BELT BYPASSFEED |
| Парткод: | 2BL06810 |
| Деталь: | PULLEY25 BYPASSFEED |
| Парткод: | 2BL06820 |
| Деталь: | DIAL BYPASSFEED |
| Парткод: | 2BL06830 |
| Деталь: | ROLLER2 BYPASSFEED |
| Парткод: | 302BL06541 |
| Деталь: | ROLLER4 BYPASSFEED |
| Парткод: | 302BL06561 |
| Деталь: | SHAFT BYPASSFEED |
| Парткод: | 302BL06741 |
| Деталь: | SPRING BYPASSFEED |
| Парткод: | 302GR06510 |
| Деталь: | BASE BYPASS FEED |
| Парткод: | 302GR08100 |
| Деталь: | FILM UPPER GUIDE |
| Парткод: | 302GR08110 |
| Деталь: | LABEL JAM A1 |
| Парткод: | 302GR34050 |
| Деталь: | LABEL JAM A2 |
| Парткод: | 302GR34060 |
| Деталь: | LABEL JAM A3 |
| Парткод: | 302GR34070 |
| Деталь: | RIGHT PULLEY,FEED |
| Парткод: | 33906660 |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | PARTS BYPASS FEED UNIT |
| Парткод: | 302GR93120 |
| Деталь: | GEAR,TONER ROLLER |
| Парткод: | 29415100 |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 2BC07860 |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | COVER BYPASSUNIT |
| Парткод: | 2BL06530 |
| Деталь: | COVER BYPASSTRAY |
| Парткод: | 2BL06600 |
| Деталь: | STAY LIFTPLATE |
| Парткод: | 2BL06650 |
| Деталь: | CAM BYPASS |
| Парткод: | 2BL06680 |
| Деталь: | MOUNT BYPASSDRIVE |
| Парткод: | 2BL06690 |
| Деталь: | GEAR 55/15 |
| Парткод: | 2BL06720 |
| Деталь: | JOINT RETARD |
| Парткод: | 2BL06850 |
| Деталь: | SPRING RETARD |
| Парткод: | 2BL06860 |
| Деталь: | SPRING JOINTRETARD |
| Парткод: | 2BL06870 |
| Деталь: | FILM BYPASS |
| Парткод: | 2BL06880 |
| Деталь: | STOPPER GEAR 8-25 |
| Парткод: | 2BL06990 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL07860 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | SHAFT RETARD |
| Парткод: | 302BL06751 |
| Деталь: | SHAFT BYPASSCAM |
| Парткод: | 302BL06761 |
| Деталь: | SHAFT BYPASS |
| Парткод: | 302BL06771 |
| Деталь: | BASE BYPASS |
| Парткод: | 302GR08010 |
| Деталь: | PLATE LIFT BYPASS |
| Парткод: | 302GR08021 |
| Деталь: | COVER CURSOR |
| Парткод: | 302GR08030 |
| Деталь: | FRONT CURSOR BYPASS |
| Парткод: | 302GR08040 |
| Деталь: | REAR CURSOR BYPASS |
| Парткод: | 302GR08050 |
| Деталь: | MOUNT SIZE PWB |
| Парткод: | 302GR08060 |
| Деталь: | RACK CURSOR |
| Парткод: | 302GR08070 |
| Деталь: | TABLE BYPASS |
| Парткод: | 302GR08080 |
| Деталь: | LABEL SET PAPER CAUTION A |
| Парткод: | 302GR34090 |
| Деталь: | LABEL BYPASS SIZE |
| Парткод: | 302GR34121 |
| Деталь: | LABEL JAM A4 |
| Парткод: | 302GR34250 |
| Деталь: | LABEL SET PAPER CAUTION |
| Парткод: | 302GR34260 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | CLUTCH FEED B |
| Парткод: | 302GR44130 |
| Деталь: | SWITCH BYPASS SIZE |
| Парткод: | 302GR44280 |
| Деталь: | WIRE BYPASS UNIT |
| Парткод: | 302GR46230 |
| Деталь: | WIRE BYPASS TRAY |
| Парткод: | 302GR46270 |
| Деталь: | JOINT,BYPASS PICKUP |
| Парткод: | 303A206131 |
| Деталь: | GEAR 16,PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | TORQUE LIMITER,BYPASS |
| Парткод: | 33906430 |
| Деталь: | FRICTION PLATE,BYPASS LEADING FEED |
| Парткод: | 34806490 |
| Деталь: | GEAR 18,CASSETTE |
| Парткод: | 34907141 |
| Деталь: | ARM,BYPASS PE |
| Парткод: | 3A206100 |
| Деталь: | HOLDER,RETARD |
| Парткод: | 3A206170 |
| Деталь: | MOUNT,BYPASS PE SWITCH |
| Парткод: | 3A206210 |
| Деталь: | UPPER PULLEY,BYPASS |
| Парткод: | 61706770 |
| Цена: | 1 900 ₽ |
| Деталь: | GEAR, 16 BYPASS PULLEY |
| Парткод: | 66006810 |
| Деталь: | PIN,CASSETTE WORK PLATE |
| Парткод: | 66007310 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | GEAR 30, FD EJECT IDLE |
| Парткод: | 72321350 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | ASSCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | EDGING, EDS-0607M(KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | MINI CLAMP, UAMS-02WL-0 (KITAGAWA) |
| Парткод: | M2105210 |
| Деталь: | LABEL BYPASS JAM R |
| Парткод: | 302GR34170 |
| Деталь: | PIN COVER |
| Парткод: | 302BL04411 |
| Деталь: | PLATE BYPASS HOLD |
| Парткод: | 2BL06890 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | CUSHION MPF A |
| Парткод: | 302GR08090 |
| Деталь: | LABEL,CAUTION GEAR |
| Парткод: | 3A205010 |
| Деталь: | PARTS BYPASS UNIT |
| Парткод: | 302GR93110 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | 2BL21070 |
| Деталь: | LEVER GUIDE CHANGE |
| Парткод: | 2BL21100 |
| Деталь: | ACTUATOR EXIT R |
| Парткод: | 2BL21120 |
| Деталь: | ACTUATOR EXIT L |
| Парткод: | 2BL21130 |
| Деталь: | BKT EXIT FULL |
| Парткод: | 2BL21150 |
| Деталь: | PLATE EARTH EXIT F |
| Парткод: | 2BL21170 |
| Деталь: | PLATE EARTH EXIT R |
| Парткод: | 2BL21180 |
| Деталь: | BKT SOLENOID |
| Парткод: | 2BL21190 |
| Деталь: | PULLEY ONEWAY T30 |
| Парткод: | 2BL21211 |
| Деталь: | GEAR EXIT Z19 |
| Парткод: | 2BL21220 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | SPRING ACTUATOR R |
| Парткод: | 2BL21250 |
| Деталь: | SPRING ACTUATOR L |
| Парткод: | 2BL21260 |
| Деталь: | SPRING FEED SHIFT |
| Парткод: | 2BL21270 |
| Деталь: | LEVER GUIDE CHANGE B |
| Парткод: | 2BL21370 |
| Деталь: | GEAR EXIT JOINT Z26S |
| Парткод: | 2BL21390 |
| Деталь: | SPRING EXIT JOINT |
| Парткод: | 2BL21400 |
| Деталь: | GEAR EXIT Z20 |
| Парткод: | 2BL21430 |
| Деталь: | SPRING EXIT CHANGE |
| Парткод: | 2BL21440 |
| Деталь: | PLATE EARTH CHANGE |
| Парткод: | 2BL21470 |
| Деталь: | SPRING EXIT FULL |
| Парткод: | 2BL21480 |
| Деталь: | CUT WASHER 6 |
| Парткод: | 2BL21510 |
| Деталь: | PULLEY EXIT C |
| Парткод: | 2BL21520 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | ROLLER EXIT |
| Парткод: | 302BL21021 |
| Деталь: | ROLLER FEED SHIFT |
| Парткод: | 302BL21031 |
| Деталь: | SHAFT EXIT PULLEY |
| Парткод: | 302BL21061 |
| Деталь: | GUIDE EXIT CHANGE |
| Парткод: | 302BL21081 |
| Деталь: | ACTUATOR EXIT FULL |
| Парткод: | 302BL21141 |
| Деталь: | BKT DISCHARGER |
| Парткод: | 302BL21161 |
| Деталь: | JOINT EXIT |
| Парткод: | 302BL21201 |
| Деталь: | WIRE EJECT(P) |
| Парткод: | 302G146070 |
| Деталь: | FRAME EXIT UP |
| Парткод: | 302GR28011 |
| Деталь: | FRAME EXIT LOW |
| Парткод: | 302GR28020 |
| Деталь: | PULLEY EXIT |
| Парткод: | 302GR28060 |
| Деталь: | SOLENOID FEED SHIFT |
| Парткод: | 302GR44160 |
| Деталь: | SWITCH,EJECT |
| Парткод: | 303BN27061 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | 34821100 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | EDGING, EDS-0607L(KITAGAWA) |
| Парткод: | M2104390 |
| Деталь: | MINIATURE CLAMP, UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | PIN EXIT |
| Парткод: | 302GR02860 |
| Деталь: | PARTS EXIT UNIT |
| Парткод: | 302G193050 |
| Деталь: | GEAR 25 |
| Парткод: | 2AL06110 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GUIDE VERTICAL FEED |
| Парткод: | 2BL06110 |
| Деталь: | MOUNT C FEED DRIVE |
| Парткод: | 2BL06130 |
| Деталь: | GEAR Z42 FEED |
| Парткод: | 2BL06170 |
| Деталь: | GEAR Z28-P18 FEED |
| Парткод: | 2BL06180 |
| Деталь: | EARTH VERTICAL FEED |
| Парткод: | 2BL06220 |
| Деталь: | BELT CONVEYING |
| Парткод: | 2BL06320 |
| Деталь: | GUIDE B FEED |
| Парткод: | 2BL06330 |
| Деталь: | GEAR Z25 JOINT |
| Парткод: | 2BL06380 |
| Цена: | 370 ₽ |
| Деталь: | HOLDER FEED SWITCH |
| Парткод: | 2BL06450 |
| Деталь: | SPRING LEFT COVER |
| Парткод: | 2BL06460 |
| Деталь: | EARTH PUSH SWITCH |
| Парткод: | 2BL06940 |
| Деталь: | STOPPER GEAR 8-25 |
| Парткод: | 2BL06990 |
| Деталь: | FRAME VERTICAL FEED A |
| Парткод: | 2FG06010 |
| Деталь: | MOUNT FEED DRIVE A |
| Парткод: | 2FG06020 |
| Деталь: | MOUNT FEED DRIVE B |
| Парткод: | 2FG06030 |
| Деталь: | GEAR Z21-Z36 FEED |
| Парткод: | 2FG06040 |
| Деталь: | SPRING FEED JOINT |
| Парткод: | 2FG06070 |
| Деталь: | COLLAR FEED JOINT |
| Парткод: | 2FG06120 |
| Деталь: | SPRING GUIDE FEED |
| Парткод: | 2FG06130 |
| Деталь: | ROLLER B FEED |
| Парткод: | 302BL06081 |
| Деталь: | ROLLER C FEED |
| Парткод: | 302BL06091 |
| Деталь: | JOINT FEED DRIVE |
| Парткод: | 302FG06051 |
| Деталь: | SHAFT FEED JOINT |
| Парткод: | 302FG06061 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | SWITCH CONVEYING |
| Парткод: | 302GR44220 |
| Деталь: | WIRE CONVEYING |
| Парткод: | 302GR46260 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | GEAR 30,IDLE |
| Парткод: | 36222250 |
| Деталь: | RING STOPPER /A-49 FEEDA4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | LOCK COVER R /40283V0068A4 |
| Парткод: | 5MVX421DN003 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC03B1106+H01 |
| Деталь: | ASSCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | FRONT RAIL FEED |
| Парткод: | 2BL06051 |
| Деталь: | REAR RAIL FEED |
| Парткод: | 2BL06061 |
| Деталь: | SHAFT LEFT COVER M |
| Парткод: | 302BL04521 |
| Деталь: | SPRING CONV OPEN |
| Парткод: | 302BL16232 |
| Деталь: | DUMPER LEFT COVER |
| Парткод: | 2BL06950 |
| Деталь: | STOPPER 7,CARTRIDGE |
| Парткод: | 33973300 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 2BL06430 |
| Деталь: | FRONT GUIDE REGIST |
| Парткод: | 2BL06260 |
| Деталь: | PARTS,REGISTRATION CLEAN |
| Парткод: | 2BL93450 |
| Цена: | 4 000 ₽ |
| Деталь: | MOUNT REGIST SWITCH |
| Парткод: | 2BL06440 |
| Деталь: | SWITCH REGISTRATION |
| Парткод: | 2FG27110 |
| Деталь: | WIRE RESISTRATION |
| Парткод: | 302GR46240 |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | RIGHT ROLLER REGIST |
| Парткод: | 302FG06211 |
| Деталь: | GUIDE A FEED |
| Парткод: | 2BL06020 |
| Деталь: | GEAR Z28 FEED |
| Парткод: | 2BL06150 |
| Деталь: | GEAR Z35-15 FEED |
| Парткод: | 2BL06160 |
| Деталь: | GEAR Z25 FEED |
| Парткод: | 2BL06190 |
| Деталь: | GROUND PLATE A FEED |
| Парткод: | 2BL06230 |
| Деталь: | GEAR Z42 BYPASS |
| Парткод: | 2BL06360 |
| Деталь: | FILM REGIST F |
| Парткод: | 2BL06480 |
| Деталь: | FILM REGIST FF |
| Парткод: | 2BL06970 |
| Деталь: | GUIDE MIDDLE FEED |
| Парткод: | 2FG06090 |
| Деталь: | PULLEY MIDDLE FEED |
| Парткод: | 2FG06110 |
| Деталь: | MOUNT MID FEED DRIVE |
| Парткод: | 2FG06150 |
| Деталь: | MOUNT BYPASS FEED |
| Парткод: | 2FG06160 |
| Деталь: | GROUND PLATE GUIDE A |
| Парткод: | 2FG06170 |
| Деталь: | FILM MIDDLE FEED |
| Парткод: | 2FG06200 |
| Деталь: | SHAFT FEED A |
| Парткод: | 302BL06921 |
| Деталь: | HOUSING FEED |
| Парткод: | 302FG06082 |
| Деталь: | SHAFT MIDDLE FEED |
| Парткод: | 302FG06101 |
| Деталь: | PULLEY MIDDLE FEED A |
| Парткод: | 302GR06010 |
| Деталь: | PULLEY MIDDLE FEED B |
| Парткод: | 302GR06020 |
| Деталь: | JOINT FEED |
| Парткод: | 302GR06030 |
| Деталь: | HOLDER WIRE |
| Парткод: | 302GR06220 |
| Деталь: | CLUTCH REGISTRATION |
| Парткод: | 302GR44140 |
| Деталь: | WIRE FEED 1 |
| Парткод: | 302GR46280 |
| Деталь: | LABEL DRUM CAUTION E1 |
| Парткод: | 2FG05080 |
| Деталь: | LABEL DRUM CAUTION E2 |
| Парткод: | 2FG05090 |
| Деталь: | LABEL DRUM CAUTION A |
| Парткод: | 2FG05100 |
| Деталь: | FILM MIDDLE FEED RAIL R |
| Парткод: | 2FG06220 |
| Деталь: | PIN FEED |
| Парткод: | 302GR02330 |
| Деталь: | PARTS VERTICAL FEED UNIT |
| Парткод: | 302GR93160 |
| Деталь: | PARTS MIDDLE FEED UNIT |
| Парткод: | 302GR93150 |
| Деталь: | PARTS,GUIDE TRANSFER |
| Парткод: | 302FG93111 |
| Деталь: | Ось пальца отделения бумаги от прижимного вала |
| Парткод: | 302AR20512 |
| Цена: | 160 ₽ |
| Деталь: | PANEL UNIT, MFC9840CDW |
| Парткод: | FK-710 |
| Цена: | 33 400 ₽ |
| Деталь: | PULL ARM L, DCP9055CDN/ MFC9460CDN/ MFC9465CDN/ MFC9560CDW |
| Парткод: | 302G145021 |
| Цена: | 19 400 ₽ |
| Деталь: | Блок лазера |
| Парткод: | LK-710 |
| Цена: | 49 300 ₽ |
| Деталь: | BUSHING,6 REGISTRATION |
| Парткод: | 29806810 |
| Деталь: | PULLEY,PAPER FEED |
| Парткод: | 2AR07220 |
| Цена: | 1 600 ₽ |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | GUIDE FILM,SEPARATION PULLEY |
| Парткод: | 2AR07660 |
| Деталь: | PULLEY FEED A |
| Парткод: | 2BJ06010 |
| Цена: | 250 ₽ |
| Деталь: | PLATE LEADING FEED |
| Парткод: | 2BL07900 |
| Деталь: | SUPPORT PLATE FEED |
| Парткод: | 2BL07910 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 2BL07990 |
| Деталь: | SHAFT,PAPER FEED |
| Парткод: | 302AR07251 |
| Деталь: | SHAFT, SEPARATION |
| Парткод: | 302AR07261 |
| Деталь: | SHAFT,LEADING FEED |
| Парткод: | 302AR07271 |
| Деталь: | UPPER HOUSING,PAPER FEED |
| Парткод: | 302FG07251 |
| Деталь: | LOWER HOUSING,PAPER FEED |
| Парткод: | 302FG07260 |
| Деталь: | WEIGHT, LEADING FEED PULLEY |
| Парткод: | 302FG07271 |
| Деталь: | ACTUATOR,PAPER EMPTY |
| Парткод: | 302FG07290 |
| Деталь: | HOLDER,ACTUATOR |
| Парткод: | 302FG07300 |
| Деталь: | REINFORCEMENT PRIMARY PAPER FEED |
| Парткод: | 302FG07310 |
| Деталь: | STOPPER,SUPPORT PLATE |
| Парткод: | 302FG07320 |
| Деталь: | GROUND PLATE,PRIMARY PAPER FEED |
| Парткод: | 302FG07330 |
| Деталь: | LEVER SEPARATION RELEASE |
| Парткод: | 302GR06200 |
| Деталь: | WIRE PRIMARY FEED UNIT1 |
| Парткод: | 302GR46430 |
| Деталь: | TORQUE LIMITER,PAPER FEED |
| Парткод: | 33906070 |
| Деталь: | GEAR 16,PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | LOWER BUSHING,PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | GEAR 15 |
| Парткод: | 34922420 |
| Деталь: | PT.SENSOR GP1A73AJ00/BK |
| Парткод: | 5FNXGP1A73A++02 |
| Деталь: | RING STOPPER /A-49 FEEDA4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H01 |
| Деталь: | PARTS PRIMARY PAPER FEED UNIT |
| Парткод: | 302GR93020 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PLATE DRIVE CONT B |
| Парткод: | 2BL22450 |
| Деталь: | GEAR Z24S-P40 |
| Парткод: | 2BL22480 |
| Деталь: | GEAR Z40S-Z25S |
| Парткод: | 2BL22490 |
| Деталь: | SPRING DRIVE CONT. |
| Парткод: | 2BL22510 |
| Деталь: | CLUTCH CONTAINER |
| Парткод: | 2BL22520 |
| Деталь: | PULLEY CONT DRIVE |
| Парткод: | 2BL22560 |
| Деталь: | BUSH DRIVE CONT 8 |
| Парткод: | 2BL22570 |
| Деталь: | BELT DRIVE CONTAINER |
| Парткод: | 2BL22590 |
| Деталь: | PLATE DRIVE CONT.A |
| Парткод: | 302BL22441 |
| Деталь: | SHAFT DRIVE CONT |
| Парткод: | 302BL22461 |
| Деталь: | COUPLING K CONT |
| Парткод: | 302G131010 |
| Деталь: | COUPLING L CONT |
| Парткод: | 302G131020 |
| Деталь: | SOLENOID TONER |
| Парткод: | 302GR44150 |
| Цена: | 400 ₽ |
| Деталь: | WIRE CONT SW |
| Парткод: | 302GR46250 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | ASSCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | WIRE SADDLE,YMW-16(KITAGAWA) |
| Парткод: | M2109410 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | RING STOPPER /A-49 FEEDA4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GEAR M FEED Z25 /D1026A4 |
| Парткод: | 5MVG137DB025 |
| Деталь: | GEAR FEED Z41S-P15 |
| Парткод: | 2BL22530 |
| Деталь: | MOTOR LIFT |
| Парткод: | 302GR44110 |
| Деталь: | BRACKET CLUTCH FEED |
| Парткод: | 2FG22090 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | GEAR Z60S-P20 |
| Парткод: | 2BL22540 |
| Деталь: | PRIMARY PAPER FEED BUSHING ASSY |
| Парткод: | 2AR00170 |
| Деталь: | GEAR Z41S P18 |
| Парткод: | 2BL22420 |
| Деталь: | BELT DRIVE MPF |
| Парткод: | 2BL22400 |
| Деталь: | PLATE DRIVE MPF A |
| Парткод: | 302BL22371 |
| Деталь: | GEAR Z40S-Z32S |
| Парткод: | 2BL22550 |
| Цена: | 550 ₽ |
| Деталь: | PLATE DRIVE MPF B |
| Парткод: | 2BL22380 |
| Деталь: | PLATE DRIVE FEED A |
| Парткод: | 302FG22071 |
| Деталь: | PARTS,MOTOR FEED SP |
| Парткод: | 302GR94260 |
| Деталь: | GEAR Z76H-Z35S |
| Парткод: | 2BL22320 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510009++H01 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | PLATE TENSION A |
| Парткод: | 302BL22811 |
| Деталь: | PIN DRIVE TENSION |
| Парткод: | 302GR02820 |
| Деталь: | PULLEY TENSION |
| Парткод: | 2BL22830 |
| Деталь: | SPRING PULLEY |
| Парткод: | 2BL22820 |
| Деталь: | PULLEY MPF DRIVE |
| Парткод: | 302BL22391 |
| Деталь: | PLATE DRIVE FEED B |
| Парткод: | 2FG22080 |
| Деталь: | GEAR Z41S-Z24S-P30 |
| Парткод: | 2BL22330 |
| Деталь: | BELT DRIVE FEED |
| Парткод: | 2BL22350 |
| Деталь: | COLLAR BELT DRIVE |
| Парткод: | 302FG22120 |
| Деталь: | WIRE SADDLE,YMC-15-0(KITAGAWA) |
| Парткод: | M2109350 |
| Деталь: | PARTS CONT DRIVE A ASSY |
| Парткод: | 302G193060 |
| Деталь: | PARTS CONT DRIVE E ASSY |
| Парткод: | 302G193070 |
| Деталь: | CLAW HEAT ROLLER |
| Парткод: | 2BL20080 |
| Деталь: | GEAR FIXING Z33 |
| Парткод: | 2BL20260 |
| Деталь: | STATIC ELIMINATOR PRESS |
| Парткод: | 2BL20330 |
| Деталь: | GEAR 49 HEAT ROLLER |
| Парткод: | 2FG20070 |
| Деталь: | BUSHING HEAT ROLLER |
| Парткод: | 2FG20190 |
| Деталь: | BEARING HEAT ROLLER |
| Парткод: | 2FG20230 |
| Деталь: | STATIC ELIMINATOR HEAT ROLLER |
| Парткод: | 302F725430 |
| Деталь: | THERMISTOR FIXING |
| Парткод: | 302FG20211 |
| Цена: | 2 100 ₽ |
| Деталь: | STOPPER HEAT ROLLER |
| Парткод: | 302G125030 |
| Деталь: | SPRING PRESSURE |
| Парткод: | 302G125070 |
| Деталь: | PARTS,ROLLER HEAT SP |
| Парткод: | 302G194020 |
| Цена: | 6 700 ₽ |
| Деталь: | PARTS,HEATER 120 FUSER SP |
| Парткод: | 302G194030 |
| Деталь: | PARTS,HEATER 230 FUSER SP |
| Парткод: | 302G194040 |
| Деталь: | UPPER FRAME FUSER |
| Парткод: | 302GR25010 |
| Деталь: | LOWER FRAME FUSER |
| Парткод: | 302GR25021 |
| Деталь: | Guide Chute |
| Парткод: | 302GR25030 |
| Деталь: | FRONT FRAME FUSER |
| Парткод: | 302GR25040 |
| Деталь: | REAR FRAME FUSER |
| Парткод: | 302GR25050 |
| Деталь: | FRONT PRESSING PLATE |
| Парткод: | 302GR25060 |
| Деталь: | REAR PRESSING PLATE |
| Парткод: | 302GR25070 |
| Деталь: | STAY RIGHT FUSER |
| Парткод: | 302GR25080 |
| Деталь: | PLATE GUIDE CHUTE |
| Парткод: | 302GR25100 |
| Деталь: | PIN LOWER FRAME |
| Парткод: | 302GR25160 |
| Деталь: | PLATE THERMO CUT |
| Парткод: | 302GR25180 |
| Деталь: | HOLDER THERMO CUT |
| Парткод: | 302GR25200 |
| Деталь: | PIN UPPER FRAME |
| Парткод: | 302GR25210 |
| Деталь: | SPRING THERMISTOR |
| Парткод: | 302GR25220 |
| Деталь: | PLATE ELIMINATOR |
| Парткод: | 302GR25230 |
| Деталь: | PIN GUIDE CHUTE |
| Парткод: | 302GR25240 |
| Деталь: | MOUNT THERMO CUT HOLDER |
| Парткод: | 302GR25250 |
| Деталь: | GROUND PLATE FUSER |
| Парткод: | 302GR25270 |
| Деталь: | SPRING CLAW |
| Парткод: | 302GR25280 |
| Деталь: | THERMOSTAT M FUSER |
| Парткод: | 302GR25290 |
| Цена: | 2 500 ₽ |
| Деталь: | BEARING PRESSURE |
| Парткод: | 2C920330 |
| Деталь: | PARTS,THERMISTOR FUSER NC SP |
| Парткод: | 302GR94320 |
| Деталь: | NUT FUSER A/FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | ADJUSTOR FUSER |
| Парткод: | 302GR02120 |
| Деталь: | PARTS FUSER UNIT 120V |
| Парткод: | 302G193010 |
| Деталь: | PARTS FUSER UNIT 230V |
| Парткод: | 302G193020 |
| Деталь: | PARTS, ROLLER PRESS SP |
| Парткод: | 302GR94280 |
| Деталь: | GEAR SPIRAL 16 |
| Парткод: | 2BL18160 |
| Деталь: | GEAR IDLE 15 |
| Парткод: | 2BL18170 |
| Деталь: | BLADE CLEANING |
| Парткод: | 2BL18300 |
| Деталь: | HANDLE DRUM |
| Парткод: | 2BL18320 |
| Деталь: | SPONGE LOWER SEAL |
| Парткод: | 2BL18560 |
| Деталь: | BUSHING DRUM A |
| Парткод: | 2BL18630 |
| Деталь: | GEAR CL ROLLER 15 |
| Парткод: | 2BL18870 |
| Деталь: | GEAR CL ROLLER 16 |
| Парткод: | 2BL18880 |
| Деталь: | PARTS,LAMP CLEANING ASSY |
| Парткод: | 2BL93420 |
| Деталь: | REAR COVER DRUM |
| Парткод: | 302BL18031 |
| Деталь: | FRONT COVER DRUM |
| Парткод: | 302GR12010 |
| Деталь: | LOWER SEAL CLEANING |
| Парткод: | 302GR12110 |
| Деталь: | MC-710 |
| Парткод: | 302GR93070 |
| Деталь: | PARTS CLAW SEPARATION ASSY |
| Парткод: | 302GR93190 |
| Деталь: | PARTS MCH MOTOR ASSY |
| Парткод: | 302GR94450 |
| Деталь: | DK-710 |
| Парткод: | 302G193030 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 2BC07860 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | PLATE NUMBER 2 |
| Парткод: | 2BL04370 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 2C904550 |
| Деталь: | PIN CURSOR |
| Парткод: | 2FB07050 |
| Деталь: | SPRING CURSOR |
| Парткод: | 2FB07060 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | SHAFT, WORK PLATE |
| Парткод: | 302AR07041 |
| Деталь: | WORK PLATE,LIFT CASSETTE |
| Парткод: | 302BC06091 |
| Деталь: | LEVER CURSOR A |
| Парткод: | 302FB07032 |
| Деталь: | LEVER CURSOR B |
| Парткод: | 302FB07042 |
| Деталь: | ADJUSTING PLATE CASSETTE |
| Парткод: | 302FB07340 |
| Деталь: | PIN CASSETTE |
| Парткод: | 302FB07420 |
| Деталь: | BASE CASSETTE |
| Парткод: | 302FG07091 |
| Деталь: | CURSOR C CASSETTE |
| Парткод: | 302FG07151 |
| Деталь: | FRONT GUIDE C,CURSOR |
| Парткод: | 302FG07170 |
| Деталь: | REAR GUIDE C,CURSOR |
| Парткод: | 302FG07180 |
| Деталь: | GROUND PLATE,CASSETTE |
| Парткод: | 302FG07200 |
| Деталь: | STOPPER,TRAILING EDGE DETECTION |
| Парткод: | 302FG07230 |
| Деталь: | CASSETTE |
| Парткод: | 302GR09010 |
| Деталь: | HANDLE CASSETTE 1 |
| Парткод: | 302GR09020 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302GR09030 |
| Деталь: | HANDLE CASSETTE 2 |
| Парткод: | 302GR09040 |
| Деталь: | LEVER CASSETTE |
| Парткод: | 302GR09050 |
| Деталь: | RAIL CURSOR R |
| Парткод: | 302GR09060 |
| Деталь: | LID PAPER SIZE |
| Парткод: | 302GR09070 |
| Деталь: | RAIL CURSOR A |
| Парткод: | 302GR09080 |
| Деталь: | Support Plate |
| Парткод: | 302GR09090 |
| Деталь: | FRONT CURSOR CASSETTE |
| Парткод: | 302GR09102 |
| Деталь: | REAR CURSOR CASSETTE |
| Парткод: | 302GR09112 |
| Деталь: | SPRING LEVER CASSETTE |
| Парткод: | 302GR09120 |
| Деталь: | SHAFT PULLEY |
| Парткод: | 302GR09130 |
| Деталь: | SHAFT HANDLE |
| Парткод: | 302GR09140 |
| Деталь: | WORK PLATE HANDLE |
| Парткод: | 302GR09150 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302GR09160 |
| Деталь: | PLATE SIZE INCH |
| Парткод: | 302GR09201 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09990 |
| Деталь: | LABEL CASSETTE OPERATION |
| Парткод: | 302GR34010 |
| Деталь: | LABEL PAPER SIZE |
| Парткод: | 302GR34021 |
| Деталь: | LABEL PAPER SIZE R |
| Парткод: | 302GR34031 |
| Деталь: | WIRE CASSETTE UNIT |
| Парткод: | 302GR46450 |
| Деталь: | DETECTION PLATE,PAPER SIZE |
| Парткод: | 33907170 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | PULLEY,CASSETTE |
| Парткод: | 34907150 |
| Деталь: | PLATE NUMBER4 |
| Парткод: | 3CF04060 |
| Деталь: | RETAINER M4 |
| Парткод: | 3CY06030 |
| Деталь: | RACK CURSOR |
| Парткод: | 3CY06090 |
| Деталь: | GEAR 20,CURSOR |
| Парткод: | 3CY06100 |
| Деталь: | PLATE SIZE C /2BL06470AA4 |
| Парткод: | 5MVS446VE001 |
| Деталь: | PLATE NUMBER 3/3CF0405A4 |
| Парткод: | 5MVX321CE001 |
| Деталь: | CUSHION,CASSETTE R |
| Парткод: | 60907170 |
| Деталь: | LABEL,PAPER UPPER LIMIT |
| Парткод: | 61705110 |
| Деталь: | SPRING, PAD |
| Парткод: | 66106080 |
| Деталь: | PAD,CASSETTE |
| Парткод: | 66107100 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H01 |
| Деталь: | PLATE SIZE C |
| Парткод: | 302FB05200 |
| Деталь: | CT-710 |
| Парткод: | 302GR93080 |
| Деталь: | Вентилятор блока лазера |
| Парткод: | 302GR44080 |
| Цена: | 2 800 ₽ |
| Деталь: | Направляющая в узле регистрации, в сборе |
| Парткод: | 302GR94481 |
| Цена: | 3 000 ₽ |
| Деталь: | GUIDE DU FEED R |
| Парткод: | 2BL21350 |
| Деталь: | PARTS,EMBLEM ASSY SP |
| Парткод: | 302G194010 |
| Деталь: | MOUNT HINGE |
| Парткод: | 2BL04220 |
| Деталь: | COVER EXIT LOW |
| Парткод: | 302BL04101 |
| Деталь: | KEY OPERATION D |
| Парткод: | 2BL04050 |
| Деталь: | KEY OPERATION C |
| Парткод: | 2BL04280 |
| Деталь: | LOWER COVER KEY |
| Парткод: | 302BL04241 |
| Деталь: | PANEL PWB ASSY |
| Парткод: | 302G101050 |
| Деталь: | KEY GO |
| Парткод: | 302G105030 |
| Деталь: | KEY CANCELL |
| Парткод: | 302G105040 |
| Деталь: | SPONGE FRONT |
| Парткод: | 2BL06620 |
| Деталь: | LEVER CONT RELEASE |
| Парткод: | 2BL04200 |
| Деталь: | INNER RIGHT COVER |
| Парткод: | 302GR04320 |
| Деталь: | COVER TOP EJECT |
| Парткод: | 302GR04011 |
| Деталь: | COVER RIGHT FRONT |
| Парткод: | 302GR04030 |
| Деталь: | COVER CENTER FRONT |
| Парткод: | 302GR04020 |
| Деталь: | MAGNET CATCH |
| Парткод: | 2FB04220 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 2BL04330 |
| Деталь: | FRONT HINGE COVER P |
| Парткод: | 2BL04350 |
| Деталь: | PIN COVER HINGE |
| Парткод: | 302BL04191 |
| Деталь: | COVER LEFT FRONT LOW |
| Парткод: | 302GR04040 |
| Деталь: | COVER LEFT FRONT |
| Парткод: | 302G104040 |
| Деталь: | STOPPER PAPER P |
| Парткод: | 302BL04401 |
| Деталь: | Rear Left Cover |
| Парткод: | 302BL04121 |
| Деталь: | FRONT LEFT COVER |
| Парткод: | 302BL04111 |
| Деталь: | LID COVER LEFT |
| Парткод: | 302BL04301 |
| Деталь: | COVER RIGHT SIDE LOW |
| Парткод: | 302GR04080 |
| Деталь: | LABEL CONTAINER |
| Парткод: | 302GR34200 |
| Деталь: | LABEL ENERGY STAR |
| Парткод: | 302G634070 |
| Деталь: | COVER LCD |
| Парткод: | 2BL04250 |
| Деталь: | COVER UPPER OPERATION 40 (40ppm) |
| Парткод: | 302GZ05010 |
| Деталь: | COVER UPPER OPERATION 50 (50ppm) |
| Парткод: | 302G105010 |
| Деталь: | SHEET OPERATION E |
| Парткод: | 302G105020 |
| Деталь: | LABEL OPERATION SHEET |
| Парткод: | 302F805040 |
| Деталь: | PIN COVER HINGE S |
| Парткод: | 302BL04841 |
| Деталь: | FRONT HINGE S COVER |
| Парткод: | 2BL04480 |
| Деталь: | LABEL SEP CLEANING |
| Парткод: | 302GR34180 |
| Деталь: | LABEL CONVEYING JAM |
| Парткод: | 302GR34190 |
| Деталь: | BRUSH CLEANER |
| Парткод: | 2BL16220 |
| Деталь: | COVER MAIN SW |
| Парткод: | 302GR04170 |
| Деталь: | FILM HINGE |
| Парткод: | 2BL04880 |
| Деталь: | LEFT TOP COVER |
| Парткод: | 2BL04170 |
| Деталь: | PIN COVER |
| Парткод: | 302BL04411 |
| Деталь: | REAR TOP COVER |
| Парткод: | 2BL04181 |
| Деталь: | COVER RIGHT TOP |
| Парткод: | 302G104020 |
| Деталь: | TRAY SUB |
| Парткод: | 302G104030 |
| Деталь: | WIRE OPE FRONT |
| Парткод: | 302G146040 |
| Деталь: | COVER REAR |
| Парткод: | 302G104010 |
| Деталь: | COVER OZONE |
| Парткод: | 302GR04250 |
| Деталь: | HOUSING OZONE COVER |
| Парткод: | 302GR04260 |
| Деталь: | FILTER OZONE B |
| Парткод: | 302FG23050 |
| Деталь: | COVER UPPER REAR |
| Парткод: | 302G104050 |
| Деталь: | CORE 7-15X18 |
| Парткод: | 33927590 |
| Деталь: | PARTS OPERATION UNIT |
| Парткод: | 302G193090 |
| Деталь: | PARTS UPPER COVER KEY 40 ASSY (40ppm) |
| Парткод: | 302GZ94010 |
| Деталь: | PARTS UPPER COVER KEY 50 ASSY (50ppm) |
| Парткод: | 302G194050 |
| Деталь: | FRONT FRAME |
| Парткод: | 302FG02042 |
| Деталь: | REAR FRAME |
| Парткод: | 302FG02051 |
| Деталь: | BASE |
| Парткод: | 2BL02030 |
| Деталь: | BASE MIDDLE |
| Парткод: | 302BL02041 |
| Деталь: | MOUNT OPERATION |
| Парткод: | 2BL04290 |
| Деталь: | MOUNT, PAPER FEED DRAWER |
| Парткод: | 2AR07710 |
| Деталь: | WIRE PRIMARY FEED UNIT2 |
| Парткод: | 302GR46440 |
| Деталь: | RETAINING PIN,DRAWER |
| Парткод: | 3033927451 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC08B2046+H02 |
| Деталь: | LOWER LEFT REINFORCEMENT |
| Парткод: | 302FG02071 |
| Деталь: | LEFT RAIL CASSETTE |
| Парткод: | 302FG07032 |
| Деталь: | PULLEY,CASSETTE RAIL |
| Парткод: | 302FG07020 |
| Деталь: | PIN FRONT CASSETTE RAIL |
| Парткод: | 302GR02240 |
| Деталь: | PIN CASSETTE RAIL |
| Парткод: | 2FB06710 |
| Деталь: | BINDING BAND SG-130 |
| Парткод: | M2107120 |
| Деталь: | PIN HANDLE |
| Парткод: | 302BL02171 |
| Деталь: | LABEL L,HIGH TEMPERATURE CAUTION(EXP) |
| Парткод: | 20305130 |
| Деталь: | LOWER RIGHT REINFORCEMENT |
| Парткод: | 302GR02250 |
| Деталь: | LEVER LOCK CASSETTE |
| Парткод: | 302GR02221 |
| Деталь: | SPRING LEVER |
| Парткод: | 302GR02230 |
| Деталь: | MOUNT TRAY EJECT |
| Парткод: | 302GR02130 |
| Деталь: | UPPER PLATE FIXING |
| Парткод: | 302GR02550 |
| Деталь: | UPPER PLATE DRUM |
| Парткод: | 302GR02110 |
| Деталь: | LOWER PLATE CONT |
| Парткод: | 2BL02130 |
| Деталь: | LOWER BASE LSU |
| Парткод: | 2BL02050 |
| Деталь: | MOUNT COVER REAR R |
| Парткод: | 302G104070 |
| Деталь: | LABEL RADIATION |
| Парткод: | 2BL05150 |
| Деталь: | HANDLE MACHINE |
| Парткод: | 302GR02350 |
| Деталь: | SPRING BYPASS RET |
| Парткод: | 2BL06840 |
| Деталь: | BASE RUBBER |
| Парткод: | 2AR02180 |
| Деталь: | UPPER RIGHT PLATE |
| Парткод: | 302BL02122 |
| Деталь: | RIGHT HANDLE MACHINE |
| Парткод: | 302GR02340 |
| Деталь: | MOUNT RIGHT HANDLE |
| Парткод: | 2BL02150 |
| Деталь: | FILM HINGE |
| Парткод: | 2BL04880 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BL06590 |
| Деталь: | MOUNT HINGE S |
| Парткод: | 2BL04470 |
| Деталь: | GROUND PLATE MIDDLE |
| Парткод: | 2BL06410 |
| Деталь: | COVER,CASSETTE RAIL |
| Парткод: | 2AR07720 |
| Деталь: | ASSCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | WIRE DEHUMIDIFIER HEATER JUNCTION |
| Парткод: | 302GR46740 |
| Деталь: | HEATER DEHUMIDIFIER 120 |
| Парткод: | 302FB25051 |
| Деталь: | HEATER DEHUMIDIFIER 240 |
| Парткод: | 302FB25060 |
| Деталь: | Ось узла подачи бумаги |
| Парткод: | 302AR07252 |
| Цена: | 420 ₽ |
| Деталь: | Узел подачи бумаги, в сборе |
| Парткод: | 302GR93022 |
| Цена: | 8 700 ₽ |
| Деталь: | PARTS,PWB ENGINE ASSY SP |
| Парткод: | 302G194060 |
| Деталь: | BOX MOUNT PWB |
| Парткод: | 302G139010 |
| Деталь: | PARTS,FAN CONTROLLER 80-15 SP |
| Парткод: | 302GR94220 |
| Деталь: | ASSCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | HOLDER PWB |
| Парткод: | 302G139090 |
| Деталь: | RAIL OPTION A /B-05 CONT BOX A2 |
| Парткод: | 5MVB743SL004 |
| Деталь: | RAIL OPTION B /B-05 CONT BOX A2 |
| Парткод: | 5MVB743SL005 |
| Деталь: | GUID CF CARD /45252C0006A4 |
| Парткод: | 5MVX621SH003 |
| Деталь: | PLATE,OPTION |
| Парткод: | 303BH26021 |
| Деталь: | SCREW OP/ M3 X 8 CRFREE A4 |
| Парткод: | 5MMT263SN012++R |
| Деталь: | WIRE MAIN-ENGINE PWB |
| Парткод: | 302G146020 |
| Деталь: | WIRE FAN |
| Парткод: | 302GR46630 |
| Деталь: | MOUNT MAIN PWB |
| Парткод: | 302G139020 |
| Деталь: | MAIN PWB ASSY (40ppm) |
| Парткод: | 302GZ47010 |
| Цена: | 101 000 ₽ |
| Деталь: | MAIN PWB ASSY (50ppm) |
| Парткод: | 302G147010 |
| Цена: | 103 000 ₽ |
| Деталь: | CORE ATFC-16-8-16 |
| Парткод: | 2FG27640 |
| Деталь: | CODE DIMM PWB ASSY WITH SOFTWARE |
| Парткод: | 302G101040 |
| Деталь: | WIRE POWER-MAIN |
| Парткод: | 302G146030 |
| Деталь: | LID BOX MOUNT |
| Парткод: | 302G139030 |
| Деталь: | LID MAIN PWB |
| Парткод: | 302G139040 |
| Деталь: | LID SIMM |
| Парткод: | 302G139050 |
| Деталь: | HOLDER USB KEY |
| Парткод: | 302GR39170 |
| Деталь: | CORE 8-20X34 |
| Парткод: | 2BL27660 |
| Деталь: | DV-710 |
| Парткод: | 302G193040 |
| Деталь: | FRONT ARM RAIL |
| Парткод: | 2BL14180 |
| Деталь: | REAR ARM RAIL |
| Парткод: | 2BL14190 |
| Деталь: | RAIL DLP |
| Парткод: | 2BL14200 |
| Деталь: | LEVER DLP |
| Парткод: | 2BL14210 |
| Деталь: | PIN LEVER DLP |
| Парткод: | 2BL14220 |
| Деталь: | GROUND PLATE RAIL |
| Парткод: | 2BL14350 |
| Деталь: | SEAL WIRE |
| Парткод: | 2BL14480 |
| Деталь: | PIN DLP RAIL |
| Парткод: | 302GR02850 |
| Деталь: | PIN,JAM REMOVEMENT DIAL |
| Парткод: | 3036006141 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC10B1112+H01 |
| Деталь: | GEAR DRUM Z70H |
| Парткод: | 2BL22050 |
| Деталь: | GUIDE DLP |
| Парткод: | 2BL22140 |
| Деталь: | GEAR DRUM Z76H-Z30H |
| Парткод: | 2BL22160 |
| Деталь: | PLATE GUIDE DRUM |
| Парткод: | 2BL22170 |
| Деталь: | GEAR Z37H-Z28H |
| Парткод: | 2BL22180 |
| Деталь: | GEAR Z50H |
| Парткод: | 2BL22190 |
| Деталь: | GEAR JOINT Z32S |
| Парткод: | 2BL22210 |
| Деталь: | GEAR Z36S-Z31H |
| Парткод: | 2BL22220 |
| Деталь: | GEAR Z34H |
| Парткод: | 2BL22230 |
| Деталь: | SPRING JOINT FUSER |
| Парткод: | 2BL22240 |
| Деталь: | SHAFT DRIVE DRUM FW |
| Парткод: | 2BL22840 |
| Деталь: | PLATE DRIVE FRONT |
| Парткод: | 2FG22010 |
| Деталь: | GEAR Z59H-Z44S |
| Парткод: | 2FG22030 |
| Деталь: | GEAR Z22S |
| Парткод: | 2FG22040 |
| Деталь: | PLATE DRIVE REAR |
| Парткод: | 302FG22021 |
| Деталь: | MOTOR MAIN |
| Парткод: | 302GR44100 |
| Деталь: | GEAR Z37S/40633V0081A4 |
| Парткод: | 5MVG148DN027 |
| Деталь: | GEAR Z76H-Z35H/30633D0068A3 |
| Парткод: | 5MVG169DN019 |
| Деталь: | BEARING 6900ZZNR |
| Парткод: | G3169000 |
| Деталь: | PLATE DRUM COVER |
| Парткод: | 302GR02140 |
| Деталь: | MOTOR EJECT |
| Парткод: | 302GR44090 |
| Цена: | 3 800 ₽ |
| Деталь: | PLATE DRIVE EXIT A |
| Парткод: | 302FG22051 |
| Деталь: | GEAR Z47S-Z28S |
| Парткод: | 2BL22800 |
| Деталь: | GEAR EXIT Z30S |
| Парткод: | 2BL22630 |
| Деталь: | CLUTCH REGISTRATION |
| Парткод: | 302GR44140 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | DUCT UPPER DRUM |
| Парткод: | 302GR33010 |
| Деталь: | COVER DUCT DRUM |
| Парткод: | 2BL23120 |
| Деталь: | DUCT UPPER CONT |
| Парткод: | 302GR33020 |
| Деталь: | PARTS,FAN FIXING 80-25 SP |
| Парткод: | 302GR94230 |
| Деталь: | LID DLP DUCT |
| Парткод: | 2BL23040 |
| Деталь: | RETAINER FLYWHEEL |
| Парткод: | 2BL22850 |
| Деталь: | FLYWHEEL 190 |
| Парткод: | 2BL22860 |
| Деталь: | WEIGHT 190 |
| Парткод: | 2BL22870 |
| Деталь: | MOUNT BASE TERMINAL |
| Парткод: | 2BL26150 |
| Деталь: | PLATE TRANSFER A |
| Парткод: | 2BL26160 |
| Деталь: | PLATE SEPARATION A |
| Парткод: | 2BL26170 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 302GR01250 |
| Деталь: | DUCT MAIN A |
| Парткод: | 302BL23051 |
| Деталь: | DUCT MAIN B |
| Парткод: | 2BL23060 |
| Деталь: | PARTS,FAN LSU 90-25 SP |
| Парткод: | 302GR94240 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | WIRE CONTAINER |
| Парткод: | 302GR46210 |
| Деталь: | RAIL DRUM R |
| Парткод: | 2BL02220 |
| Деталь: | ASSCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PLATE DRIVE EXIT B |
| Парткод: | 2FG22060 |
| Деталь: | MOUNT FLYWHEEL |
| Парткод: | 2BL22890 |
| Деталь: | FILM COOLING |
| Парткод: | 2BL23100 |
| Деталь: | FILM BKT CLUTCH |
| Парткод: | 2BL22880 |
| Деталь: | BRACKET CLUTCH |
| Парткод: | 2BL22150 |
| Деталь: | BUSH,CUTTER |
| Парткод: | 213+4410 |
| Деталь: | FILM SPRING DRUM COVER |
| Парткод: | 302GR02560 |
| Деталь: | HOLDER RFID |
| Парткод: | 302GR33030 |
| Деталь: | R/W MODULE 26X45 |
| Парткод: | 302F845040 |
| Деталь: | WIRE RFID |
| Парткод: | 302GR46590 |
| Деталь: | COVER DRUM A |
| Парткод: | 302GR02011 |
| Деталь: | SHAFT DRUM COVER |
| Парткод: | 302GR02020 |
| Деталь: | HOLDER SHAFT F |
| Парткод: | 302GR02030 |
| Деталь: | HOLDER SHAFT R |
| Парткод: | 302GR02040 |
| Деталь: | GUIDE STRAP |
| Парткод: | 302GR02050 |
| Деталь: | STRAP DRUM COVER |
| Парткод: | 302GR02060 |
| Деталь: | ARM DRUM COVER A |
| Парткод: | 302GR02070 |
| Деталь: | ARM DRUM COVER B |
| Парткод: | 302GR02080 |
| Деталь: | PULLEY,DRUM SEPARATION |
| Парткод: | 2A118370 |
| Цена: | 90 ₽ |
| Деталь: | STOPPER 3/2BT1107A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | SPRING DRUM COVER |
| Парткод: | 302GR02090 |
| Деталь: | CUSHION DRUM COVER B |
| Парткод: | 302GR02150 |
| Деталь: | CUSHION DRUM COVER C |
| Парткод: | 302GR02160 |
| Деталь: | CUSHION DRUM COVER D |
| Парткод: | 302GR02170 |
| Деталь: | DR-710 |
| Парткод: | 302GR93200 |
| Деталь: | GEAR 25 |
| Парткод: | 2AL06110 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | ROLLER DU FEED UP |
| Парткод: | 2BL07020 |
| Деталь: | ROLLER DU FEED LOW |
| Парткод: | 2BL07030 |
| Деталь: | PULLEY DU |
| Парткод: | 2BL07040 |
| Деталь: | SPRING DU PULLEY |
| Парткод: | 2BL07060 |
| Деталь: | SPRING DU JOINT |
| Парткод: | 2BL07080 |
| Деталь: | ACTUATOR DU |
| Парткод: | 2BL07090 |
| Деталь: | PLATE EARTH DU |
| Парткод: | 2BL07110 |
| Деталь: | PLATE NUT DU |
| Парткод: | 2BL07120 |
| Деталь: | SPRING DU ACT. |
| Парткод: | 2BL07130 |
| Деталь: | FILM WIRE DU |
| Парткод: | 2BL07140 |
| Деталь: | GUIDE RIB DU |
| Парткод: | 2BL07150 |
| Деталь: | UNDER CLEANER REGIST |
| Парткод: | 2BL07950 |
| Цена: | 1 500 ₽ |
| Деталь: | CUT WASHER 10 |
| Парткод: | 2BL07970 |
| Деталь: | STOPPER BUSH |
| Парткод: | 2BL16030 |
| Деталь: | GEAR REGIST Z18 |
| Парткод: | 2BL16060 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL16080 |
| Деталь: | STRAP CONVEYING A |
| Парткод: | 2BL16100 |
| Деталь: | STRAP CONVEYING B |
| Парткод: | 2BL16110 |
| Деталь: | GUIDE REGIST F |
| Парткод: | 2BL16130 |
| Цена: | 330 ₽ |
| Деталь: | PLATE TRANS B |
| Парткод: | 2BL16150 |
| Деталь: | PLATE TRANS UNIT GND |
| Парткод: | 2BL16160 |
| Деталь: | PLATE SEPARATION B |
| Парткод: | 2BL16170 |
| Деталь: | HOOK CONVEYING |
| Парткод: | 2BL16190 |
| Деталь: | SPRING CONVEYING |
| Парткод: | 2BL16200 |
| Деталь: | GUIDE FEED F |
| Парткод: | 2BL16250 |
| Деталь: | BUSHING REGIST |
| Парткод: | 2BL16260 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | PLATE MID FEED UNIT |
| Парткод: | 2FG16010 |
| Деталь: | ROLLER REGIST |
| Парткод: | 2FG16021 |
| Деталь: | PULLEY REGIST |
| Парткод: | 2FG16030 |
| Деталь: | GUIDE ROLLER F |
| Парткод: | 2FG16160 |
| Деталь: | GUIDE ROLLER R |
| Парткод: | 2FG16170 |
| Деталь: | SPACER REGIST |
| Парткод: | 2FG16250 |
| Деталь: | SHEET CONVEYING |
| Парткод: | 2FG16270 |
| Деталь: | GUIDE FEED |
| Парткод: | 2FG16290 |
| Деталь: | SPRING REGIST F |
| Парткод: | 2FG16300 |
| Деталь: | SPRING REGIST R |
| Парткод: | 2FG16310 |
| Деталь: | SPRING FEED |
| Парткод: | 2FG16320 |
| Деталь: | HOLDER SHAFT |
| Парткод: | 2FG16330 |
| Деталь: | SHAFT DU PULLEY |
| Парткод: | 302BL07052 |
| Деталь: | JOINT DU |
| Парткод: | 302BL07071 |
| Деталь: | SHAFT CONVEYING |
| Парткод: | 302BL16211 |
| Деталь: | SPRING CONVEYING B |
| Парткод: | 302BL16241 |
| Деталь: | BASE CONVEYING A |
| Парткод: | 302FG16262 |
| Деталь: | SHFAT FEED |
| Парткод: | 302FG16281 |
| Деталь: | HANDLE CONVEYING |
| Парткод: | 302GR24010 |
| Деталь: | PLATE PAPER GUIDE |
| Парткод: | 302GR24020 |
| Деталь: | MOUNT CONVEYING FAN |
| Парткод: | 302GR24030 |
| Деталь: | FILM COVER WIRE |
| Парткод: | 302GR24040 |
| Деталь: | FRAME DU |
| Парткод: | 302GR29010 |
| Деталь: | CLUTCH FEED |
| Парткод: | 302GR44120 |
| Деталь: | FAN CONVEYING 42-10 |
| Парткод: | 302GR44250 |
| Деталь: | WIRE DUPLEX |
| Парткод: | 302GR46420 |
| Деталь: | WIRE CONVEYING FAN |
| Парткод: | 302GR46730 |
| Деталь: | RING STOPPER /A-49 FEEDA4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR 20,IDLE |
| Парткод: | 66506630 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC02B1001+H01 |
| Деталь: | BAND,KI-100(KITAGAWA) |
| Парткод: | M2107240 |
| Деталь: | HOUSING TRANSFER |
| Парткод: | 2BL17010 |
| Деталь: | PULLEY TRANS ROLLER |
| Парткод: | 2BL17040 |
| Деталь: | PLATE TRANS UNIT |
| Парткод: | 2BL17050 |
| Деталь: | BUSH TRANS ROLLER |
| Парткод: | 2BL17060 |
| Деталь: | GEAR TRANS Z25H |
| Парткод: | 2BL17090 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BL17170 |
| Деталь: | HOLDER SEPARATION A |
| Парткод: | 2FG17010 |
| Деталь: | SPRING TRANS R |
| Парткод: | 2FG17160 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 302GR22010 |
| Деталь: | BRUSH SEPARATION |
| Парткод: | 302GR22020 |
| Деталь: | SPACER SEPARATION |
| Парткод: | 302GR22030 |
| Деталь: | SPRING TRANSFER F |
| Парткод: | 302GR22050 |
| Деталь: | COLLAR TRANS ROLLER |
| Парткод: | 302GR22110 |
| Деталь: | BUSHING,CLEANING BLADE SHAFT |
| Парткод: | 75718040 |
| Деталь: | FE-710 |
| Парткод: | 302GR93140 |
| Деталь: | TR-710 |
| Парткод: | 302GR93280 |
| Деталь: | Пружина узла отделения бумаги от фотовала |
| Парткод: | 2AR18280 |
| Цена: | 130 ₽ |
| Деталь: | Блок проявки |
| Парткод: | DV-710 |
| Цена: | 43 800 ₽ |
| Деталь: | Вал переноса заряда, в сборе |
| Парткод: | TR-710 |
| Цена: | 6 600 ₽ |
| Деталь: | Узел переноса заряда в драм-картридже, в сборе |
| Парткод: | MC-710 |
| Деталь: | Крышка лотка ручной подачи бумаги |
| Парткод: | 302BL06601 |
| Цена: | 3 700 ₽ |
Коды ошибок
0150
0160
1010
1020
1030
1040
1100
1110
1120
1130
1800
1900
2000
2250
2500
2600
4000
4010
4200
5300
6000
6020
6030
6050
6400
6410
6420
7400
7410
7800
7810
7900
7910
8020
8030
8050
8060
8070
8140
8170
8180
8210
8220
8230
8300
8310
8320
8330
8340
8350
8360
8440
8460
8500
8510
8800
8900
8910
8920
8930
F000
F010
F020
F030
F040
F226
Описание
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1040 |
| Display: | GL2: W0501 The memory is full. |
| Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1100 |
| Display: | Prepare for maint cart replacement. |
| Description: | Paper Jam There is paper jammed in the All-In-One. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Clear the paper jam, and resend the print job. |
| Error code: | 1110 |
| Description: | PF lift motor 2 error (large capacity feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 2 is turned on is excluded from detection. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 2 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF Lift motor2. PF Lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor 2 and PF main PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the PF Lift sensor 2. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1120 |
| Description: | Paper feeder left lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 1 does not turn on within 30 s of paper feeder lift motor 2 turning on. |
| Causes: | Poor contact in the connector terminals. Defective paper feeder lift switch 1. Defective paper feeder lift motor 2. The paper feeder left lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper feeder lift switch 1. Check if YC5-4 on the paper feeder main PWB goes low when paper feeder lift switch 1 is turned off. If not, replace paper feeder lift switch 1. Defective paper feeder lift motor 2. Check for continuity across the coil. If none, replace paper feeder lift motor 2. The paper feeder left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | 1130 |
| Description: | Paper feeder right lift position problem (optional 3000-sheet paper feeder) Paper feeder switch 2 does not turn on within 30 s of paper feeder lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective paper feeder lift switch 2. Defective paper feeder lift motor 1. The paper feeder right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper feeder lift switch 2. Check if YC5-7 on the paper feeder main PWB goes low when paper feeder lift switch 2 is turned off. If not, replace paper feeder lift switch 2. Defective paper feeder lift motor 1. Check for continuity across the coil. If none, replace paper feeder lift motor 1. The paper feeder right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | 1800 |
| Description: | Paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| Remedy: | Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 2250 |
| Description: | Main charger cleaning motor error When the main charger cleaning motor is driven, the main charger cleaning motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. |
| Causes: | Defective harness between main charger cleaning motor and engine PWB (YC36), or improper connector insertion. Defective drive transmission system of the main charger cleaning motor. Defective main charger cleaning motor. Defective engine PWB. |
| Remedy: | Defective harness between main charger cleaning motor and engine PWB (YC36), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective drive transmission system of the main charger cleaning motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective main charger cleaning motor. Replace the main charger cleaning motor. Defective engine PWB. Replace the engine PWB. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 4000 |
| Display: | Supplies Drum End Soon. |
| Description: | Command Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 4010 |
| Description: | Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and engine PWB (YC11) Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 4200 |
| Display: | Supplies Replace Drum |
| Description: | BD steady-state error The BD signal is not detected. |
| Causes: | APC PWB (LSU). Main/Engine PWB. |
| Remedy: | APC PWB (LSU) 1. Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in. Laser scanner unit and main/engine PWB (YC2010) 2. If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring. 3. Replace the laser scanner unit. Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. |
| Error code: | 5300 |
| Description: | Eraser lamp broken detection • The current at the correct level is not detected when ASIC (U8) on the engine controller PWB (KP-992) generates the signal to activate the eraser lamp. |
| Causes: | Defective engine controller PWB (KP-992). Defective drum unit (eraser lamp or drum PWB [KP- 813]). Defective harness (2BM2864) between engine controller PWB (KP-992) and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the drum unit. Check the continuity of the harness (2BM2864). Check the insertion of connectors. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6050 |
| Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
| Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 6410 |
| Description: | Fuser unit type mismatch problem Absence of the fuser unit is detected. |
| Causes: | Fuser unit connector inserted incorrectly. Different type of the fuser unit is installed. |
| Remedy: | Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. Different type of the fuser unit is installed. Install the correct fuser unit. |
| Error code: | 6420 |
| Description: | Fuser unit fuse cut problemctor. |
| Causes: | Poor contact in the connector terminals. Fuser unit connector inserted incorrectly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC10 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. |
| Error code: | 7400 |
| Display: | Jam Tray 2 Pull the paper tray2 completely out of the machine and remove the jammed paper. |
| Description: | Developing unit connector insertion problem Absence of the developing unit is detected. |
| Causes: | Developing unit connector inserted incorrectly. Defective developing unit connector. |
| Remedy: | Developing unit connector inserted incorrectly. Reinsert the developing unit connector if necessary. Defective developing unit connector. Replace the developing unit. |
| Error code: | 7410 |
| Description: | Drum unit connector insertion problem Absence of the drum unit is detected.c |
| Causes: | Drum unit connector inserted incorrectly. Defective drum unit connector. |
| Remedy: | Drum unit connector inserted incorrectly. Reinsert the drum unit connector if necessary. Defective drum unit connector. Replace the drum unit. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 7900 |
| Display: | Jam Manual Feed Pull out the jammed paper from Manual Feed and press Start |
| Description: | Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum unit. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and engine PWB (YC15) Defective drum unit. Replace the drum unit. |
| Error code: | 7910 |
| Description: | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit and engine PWB (YC12) Defective developer unit. Replace the developer unit. |
| Error code: | 8020 |
| Description: | Punch motor error 2 Home position is not obtained in 3 s after home position is initialized or in standby. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8030 |
| Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8050 |
| Description: | Paper conveying belt motor 1 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 1 does not turn off within 1.5 s. Paper conveying belt home position sensor 1 does not turn on within 2.5 s. Jam 88 is indicated. |
| Causes: | Poor contact in the connector terminals. Defective paper conveying belt home position sensor 1. Defective paper conveying belt motor 1. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC2 on the internal tray PWB and the connector on paper conveying belt motor 1, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper conveying belt home position sensor 1. Replace paper conveying belt home position sensor 1. Defective paper conveying belt motor 1. Replace paper conveying belt motor 1. Defective PWB. Replace the internal tray PWB or finisher main PWB and check for correct operation. |
| Error code: | 8060 |
| Description: | Paper conveying belt motor 2 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 2 does not turn off within 1.5 s. Paper conveying belt home position sensor 2 does not turn on within 1.5 s. |
| Causes: | Poor contact in the connector terminals. Defective paper conveying belt home position sensor 2. Defective paper conveying belt motor 2. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 on the internal tray PWB and the connector on paper conveying belt motor 2, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper conveying belt home position sensor 2. Replace paper conveying belt home position sensor 2. Defective paper conveying belt motor 2. Replace paper conveying belt motor 2. Defective PWB. Replace the internal tray PWB or finisher main PWB and check for correct operation. |
| Error code: | 8070 |
| Description: | Internal tray communication error (optional 3000-sheet document finisher) Communication with the internal tray is not possible although the connection is detected. |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 on the finisher main PWB and the connector YC1 on the internal tray PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the internal tray PWB or finisher main PWB and check for correct operation. |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8170 |
| Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8180 |
| Description: | DF side registration motor 1 error 2 JAM6810 (jam in front of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1. 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8220 |
| Description: | Stapler shift motor 2 error (optional 3000-sheet document finisher) When operation returned to a home position is performed at the time of initial operation and a home position is not detected even if 3.5 s passed. |
| Causes: | Poor contact in the connector terminals. Defective stapler shift motor 2. Defective finisher main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC10 on the finisher main PWB and the connector of stapler shift motor 2, and the continuity across the connector terminals. Repair or replace if necessary. Defective stapler shift motor 2. Replace stapler shift motor 2. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | 8230 |
| Description: | DF staple motor error 1 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF staple sensor Replace the staple unit. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8300 |
| Description: | CF unit communication error Communication with the center- folding unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF set sensor. Defective PWB. |
| Remedy: | CF unit set switch 1. Execute U241 Booklet - Set to check the finisher switch. 2. Check that the switch and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main PWB (YC7) and DF main PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CF unit set switch. CF main PWB Replace the CF main PWB DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8310 |
| Description: | CF side registration motor 2 error When initial operation, CF side registration sensor 2 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 2. Defective CF side registration motor 2. Defective CF main PWB. |
| Remedy: | CF side registration motor 2 1. Execute U240 Booklet - Width Test to check finisher operation check. 2. Manipulate the side registration upper guide back and forth to check it can smoothly move back and forth. 3. Check that the drive from the motor reaches the side registration upper guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor. CF side registration sensor 2 1. Execute U241 Booklet - Width Up HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 2 and CF main PWB (YC20) 4. Replace the CF side registration sensor 2. CF main PWB Replace the CF main PWB |
| Error code: | 8320 |
| Description: | CF adjustment motor error When initial operation, CF adjustment sensor does not turn on within 2.5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF adjustment sensor 1, 2. Defective CF adjustment motor 1, 2. Defective CF main PWB. |
| Remedy: | CF adjustment motor1,2 1. Execute U240 Booklet - Bundle Up / Down to check the finisher operation. 2. Manipulate the fold moving belt up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold moving belt. (Check if the belt is bent.) 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment motor 1,2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF adjustment motor1,2 CF adjustment sensor1,2 1. Execute U241 Booklet - bundle Up / Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment sensor 1,2 and CF main PWB (YC20) 4. Replace the CF adjustment sensor1,2. CF main PWB Replace the CF main PWB. |
| Error code: | 8330 |
| Description: | CF blade motor error When initial operation, CF blade sensor does not turn on within 1500 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF blade sensor. Defective CF blade motor. Defective CF main PWB. |
| Remedy: | CF blade motor 1. Execute U240 Booklet - Blade to check the finisher operation. 2. Manipulate the fold blade up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold blade. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade motor and CF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF blade motor. CF blade sensor 1. Execute U241 Booklet - Blade HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade sensor and CF main PWB (YC20) 4. Replace the CF blade sensor. CF main PWB Replace the CF main PWB |
| Error code: | 8340 |
| Description: | CF staple motor error 1 Staple JAM (center-folding unit) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF staple sensor. Defective CF staple motor. Defective CF main PWB. |
| Remedy: | CF staple motor 1. Execute U240 Booklet - Staple to check the finisher operation. 2. Manipulate the staple up and down check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF staple unit and CF main PWB (YC13) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF staple motor. CF staple sensor Replace the CF staple unit. CF main PWB Replace the CF main PWB. |
| Error code: | 8350 |
| Description: | CF side registration motor 1 error When initial operation, CF side registration sensor 1 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 1. Defective CF side registration motor 1. Defective CF main PWB |
| Remedy: | CF side registration motor 1 1. Execute U240 Booklet - Width Test to check the finisher operation. 2. Manipulate the side registration lower guide back and forth to check it can smoothly operable. 3. Check that the drive from the motor reaches the side registration lower guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 1 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor 1. CF side registration sensor 1 1. Execute U241 Booklet - Width Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 1 and CF main PWB (YC20) 4. Replace the CF side registration sensor 1. CF main PWB Replace the CF main PWB |
| Error code: | 8360 |
| Description: | CF main motor error During driving the motor, the lock signal is detected for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF main motor. Defective CF main PWB. |
| Remedy: | CF main motor 1. Execute U240 Booklet - Folding to check the finisher operation. 2. Manipulate the conveying roller to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main motor and CF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF main motor. CF main PWB Replace the CF main PWB |
| Error code: | 8440 |
| Description: | Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range. |
| Causes: | The paper entry sensor connector makes poor contact. Defective paper entry sensor. The optical path of the paper entry sensor is blocked by foreign matter. Defective finisher main PWB. |
| Remedy: | The paper entry sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective paper entry sensor. Replace the paper entry sensor and check for correct operation. The optical path of the paper entry sensor is blocked by foreign matter. Remove the foreign matter. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | 8460 |
| Description: | EEPROM problem (document finisher) Reading from or writing to EEPROM cannot be performed. |
| Causes: | Defective EEPROM or DF main PWB. |
| Remedy: | Replace the DF main PWB and check for correct operation. |
| Error code: | 8500 |
| Description: | Mailbox communication error Communication failed to be established after the mailbox was hooked up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | MB main PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB main PWB (YC3) and DF main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB main PWB DF main PWB Replace the DF main PWB |
| Error code: | 8510 |
| Description: | MB conveying motor error 1 When initial operation, MB home position sensor does not turn on within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor. Defective MB main PWB. |
| Remedy: | MB conveying motor 1. If the transfer roller won’t rotate smoothly, repair its mechanism. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
| Error code: | 8800 |
| Description: | Document finisher main program error Document finisher main program error at power up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8900 |
| Description: | Document finisher backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective DF main PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB |
| Error code: | 8910 |
| Description: | Backup memory data problem (optional 3000-sheet document finisher) Read and write data does not match 3 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective punch PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the punch PWB and the connector YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective punch PWB. Replace the punch PWB and check for correct operation. |
| Error code: | 8920 |
| Description: | Backup memory data problem (optional mailbox of 3000-sheet document finisher) Read and write data does not match 3 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective mailbox main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector on the mailbox main PWB and the connector YC7 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective mailbox main PWB. Replace the mailbox main PWB and check for correct operation. |
| Error code: | 8930 |
| Description: | Center-folding unit backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective CF main PWB. |
| Remedy: | CF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main PWB (YC7) and DF main PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Install the EEPROM properly. 4. Replace the CF main PWB |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F030 |
| Description: | Main PWB system error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F226 |
| Description: | VIDEO output error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
