Kyocera FS-C5016N
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A4
Число страниц в месяц
85000
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Тип устройства |
Принтер |
Цветность печати |
цветная |
Макс. формат |
A4 |
Сканер |
|
Печать фотографий |
|
Копир |
|
Число страниц в месяц |
85 000 |
Область применения |
средний офис |
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Принтер |
|
Прямая печать |
|
Двусторонняя печать |
|
Макс, разрешение для ч/б печати |
|
| По Y | 600 |
| По X | 600 |
Сканер |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Стандарт WIA |
|
Расходные материалы |
|
Ресурс цветного картриджа/тонера |
8 000 |
Ресурс ч/б картриджа/тонера |
8 000 |
Печать на: |
|
| Этикетках |
|
| Фотобумаге |
|
| Пленках |
|
Языки управления |
|
| PostScript |
|
Лотки |
|
Подача бумаги |
|
| Стандартная | 600 |
Вывод бумаги |
|
| Стандартный | 250 |
Интерфейсы |
|
Ethernet (RJ-45) |
|
USB |
|
Инфракрасный порт |
|
LPT |
|
Память/Процессор |
|
Макс, объем памяти |
608 |
Объем памяти |
96 |
Дополнительная информация |
|
Поддержка ОС |
|
| Windows |
|
| DOS |
|
| Linux |
|
| Mac OS |
|
Уровень шума |
|
| При работе | 53 |
Габариты |
|
Вес |
22 |
Высота |
385 |
Ширина |
345 |
Глубина |
470 |
Модули
Drive Units
Upper Frame Unit
PAPER FEED
Frame MP Assembly
Primary Transfer Unit
Developer unit
PAPER CASSETTE
Drum Unit / LED Unit
Exterior Covers
FUSER UNIT
PAPER FEED UNIT
MP TRAY
Controller Box
Детали PAPER FEED
| Деталь: | DR-500A DRIVE UNIT |
| Парткод: | 2D993170 |
| Деталь: | DR-500C DRIVE UNIT |
| Парткод: | 2D993190 |
| Деталь: | PLATE DRIVE MAIN |
| Парткод: | 2D922150 |
| Деталь: | STEPPING MOTOR PRO |
| Парткод: | WNAA1000 |
| Деталь: | FAN MOTOR |
| Парткод: | WNAA1040 |
| Деталь: | GEAR Z21H-Z20H |
| Парткод: | 2D922160 |
| Деталь: | GEAR Z45H |
| Парткод: | 2D922170 |
| Деталь: | GEAR Z72H-Z22H |
| Парткод: | 2D922180 |
| Деталь: | BRACKET HV MAIN ASSY |
| Парткод: | 2D968810 |
| Деталь: | P.W.B.ASSY KP-966 |
| Парткод: | 2D901420 |
| Деталь: | BRACKET DRIVE FEED |
| Парткод: | 2D922010 |
| Деталь: | SHEET MOTOR FEED |
| Парткод: | 2D922260 |
| Деталь: | STEPPING MOTOR FEED |
| Парткод: | WNAA1010 |
| Деталь: | COVER DRIVE FEED |
| Парткод: | 2D922020 |
| Деталь: | GEAR CL Z21S |
| Парткод: | 2D922080 |
| Деталь: | CLUTCH REGIST |
| Парткод: | 2D922270 |
| Деталь: | GEAR Z30S |
| Парткод: | 2D922050 |
| Деталь: | GEAR Z35S |
| Парткод: | 2D922040 |
| Деталь: | GEAR Z38S-Z14S |
| Парткод: | 2D922060 |
| Деталь: | Gear Z38S |
| Парткод: | 2D922070 |
| Деталь: | CLUTCH FEED |
| Парткод: | YY000290 |
| Деталь: | GEAR Z56S-Z20S |
| Парткод: | 2D922030 |
| Деталь: | PLATE DRIVE FUSER |
| Парткод: | 2D922090 |
| Деталь: | STEPPING MOTOR FUSER |
| Парткод: | WNAA1020 |
| Деталь: | GEAR Z43S |
| Парткод: | 2D922130 |
| Деталь: | BUSH SHAFT CLUTCH |
| Парткод: | 2D922240 |
| Деталь: | SHAFT CLUTCH B |
| Парткод: | 2D915250 |
| Деталь: | Poly Washer |
| Парткод: | C2890150 |
| Деталь: | GEAR Z22S ASSY |
| Парткод: | 2D969870 |
| Деталь: | BUSH DRIVE FUSER |
| Парткод: | 2D915200 |
| Деталь: | GEAR DRIVE FUSER Z22 |
| Парткод: | 2D915210 |
| Деталь: | SHAFT CLUTCH |
| Парткод: | 2D922220 |
| Деталь: | GEAR Z48S |
| Парткод: | 2D922110 |
| Деталь: | GEAR Z29S ASSY |
| Парткод: | 2D969180 |
| Деталь: | GEAR Z14-Z20 |
| Парткод: | 2D922140 |
| Деталь: | GEAR Z93S-Z24S |
| Парткод: | 2D922100 |
| Деталь: | BRACKET FD GEAR ASSY |
| Парткод: | 2D968590 |
| Деталь: | BRACKET FD GEAR |
| Парткод: | 2D902390 |
| Деталь: | GEAR IDLE Z25 |
| Парткод: | 5MVG137DN014 |
| Деталь: | GEAR IDLE Z16 |
| Парткод: | 5MVG127DW004 |
| Деталь: | GEAR FD Z15-Z18 |
| Парткод: | 2D902400 |
| Деталь: | GEAR FD Z29 |
| Парткод: | 5MVG138DN048 |
| Деталь: | GEAR FD Z28 |
| Парткод: | 5MVG138DN047 |
| Деталь: | FAN MOTOR |
| Парткод: | WNAA1030 |
| Деталь: | Toner Motor Assy |
| Парткод: | 2D968610 |
| Деталь: | PIN CONTACT BIAS |
| Парткод: | 5MMT463SN001 |
| Деталь: | SPRING CONTACT CLN |
| Парткод: | 2D902580 |
| Деталь: | BUSH FRAME |
| Парткод: | 2D922250 |
| Деталь: | PLATE EARTH FUSER |
| Парткод: | 2D902380 |
| Деталь: | PLATE EARTH HV B |
| Парткод: | 2D902330 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926340 |
| Деталь: | Push Switch 01 SN |
| Парткод: | 5ESP01000101*01 |
| Деталь: | LOCK COVER M/P |
| Парткод: | 5MVX522DB006 |
| Деталь: | SP LOCK COVER M/P |
| Парткод: | 5MMW261LD051 |
| Деталь: | COVER HARNESS |
| Парткод: | 2D902370 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926260 |
| Деталь: | PLATE EARTH HV A |
| Парткод: | 2D902320 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926160 |
| Деталь: | PUSH SWITCH 03 SN |
| Парткод: | 5ESP03090001+01 |
| Деталь: | P.W.B ASSY KP-982 |
| Парткод: | 2D901540 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926060 |
| Деталь: | LEVER EF |
| Парткод: | 5MVX322DB023 |
| Деталь: | SPRING LEVER EF |
| Парткод: | 5MMW222LD002 |
| Деталь: | CLEANER ID ASSY |
| Парткод: | 2D969860 |
| Деталь: | SENSOR ID ASSY |
| Парткод: | 2D968570 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926280 |
| Деталь: | BRACKET HV DLP K ASSY |
| Парткод: | 2D969810 |
| Деталь: | BRACKET HV DLP Y ASSY |
| Парткод: | 2D969830 |
| Деталь: | BRACKET HV DLP C ASSY |
| Парткод: | 2D969820 |
| Деталь: | PLATE FRAME DRUM |
| Парткод: | 2D902170 |
| Деталь: | ROD INTERLOCK |
| Парткод: | 2D902310 |
| Деталь: | SPRING INTER LOCK |
| Парткод: | 5MMW451LD001 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926080 |
| Деталь: | TRANS ASSY |
| Парткод: | 2D927070 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926290 |
| Деталь: | PLATE SHIELD PWB |
| Парткод: | 2D902200 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926310 |
| Деталь: | P.W.B ASSY KP-1048 |
| Парткод: | 2D901800 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926230 |
| Деталь: | BRACKET HV ASSY |
| Парткод: | 2D968560 |
| Деталь: | BRACKET FAN |
| Парткод: | 2D902540 |
| Деталь: | FAN MOTOR |
| Парткод: | WNAA1050 |
| Деталь: | OZONE FILTER |
| Парткод: | 2D902530 |
| Деталь: | Plate Earth FD |
| Парткод: | 2D902550 |
| Деталь: | SPRING EARTH FD |
| Парткод: | 2D902560 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926320 |
| Деталь: | PT.SENSOR EE-SX1235A |
| Парткод: | 2BZ16530 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926240 |
| Деталь: | BUSH FD |
| Парткод: | 5MVM266DN006 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926120 |
| Деталь: | ROLLER FD LOW |
| Парткод: | 2D902690 |
| Деталь: | ROLLER PINCH |
| Парткод: | 5MVM273DB006 |
| Деталь: | BRACKET ROLLER PINCH |
| Парткод: | 2D902410 |
| Деталь: | GEAR ROLL FD Z18 |
| Парткод: | 5MVG127DN076 |
| Деталь: | WASTE TONER ASSY |
| Парткод: | 2D968520 |
| Деталь: | TRANS ASSY |
| Парткод: | 2D927060 |
| Деталь: | Узел переноса изображения |
| Парткод: | TR-521 |
| Деталь: | FRAME MP ASSY |
| Парткод: | 2D968390 |
| Деталь: | FRAME M/P |
| Парткод: | 5MVX866CH001 |
| Деталь: | SPRING MID M/P |
| Парткод: | 5MMW601SD001 |
| Деталь: | BUSH MID M/P |
| Парткод: | 5MVX321DN014 |
| Деталь: | ROLL MID M/P ASSY |
| Парткод: | 5AAVR0LL+050 |
| Деталь: | SHAFT MID B |
| Парткод: | 5MVT676CB003 |
| Деталь: | SOLENOID M/P ASSY |
| Парткод: | WSAA0160 |
| Деталь: | GEAR M/P Z27 |
| Парткод: | 5MVG133DN008 |
| Деталь: | GEAR MID Z42S |
| Парткод: | 2D916010 |
| Деталь: | HOLDER CLUTCH M/P |
| Парткод: | 5MVX662DN003 |
| Деталь: | GEAR M/P Z40 |
| Парткод: | 5MVG148DN063 |
| Деталь: | LEVER CAM |
| Парткод: | 5MVX522DN004 |
| Деталь: | ROLLER M/P ASSY |
| Парткод: | 5AAVR0LL+051 |
| Цена: | 800 ₽ |
| Деталь: | SPRING CAM M/P |
| Парткод: | 5MMW161LD043 |
| Деталь: | CAM M/P |
| Парткод: | 5MVX433DN002 |
| Деталь: | ACTUATOR M/P C |
| Парткод: | 5MVX421SB021 |
| Деталь: | SP ACTUATOR M/P C |
| Парткод: | 5MMW161SD009 |
| Деталь: | HOLDER FEED M/P |
| Парткод: | 5MVX422DN007 |
| Деталь: | ACTUATOR M/P A |
| Парткод: | 5MVT754SB001 |
| Деталь: | ACTUATOR M/P B |
| Парткод: | 5MVX621SB010 |
| Деталь: | SP ACTUATOR M/P B |
| Парткод: | 5MMW161SD010 |
| Деталь: | DV-500K DLP UNIT K |
| Парткод: | 2D993050 |
| Деталь: | DV-502K DLP UNIT K |
| Парткод: | 2D993260 |
| Деталь: | DV-500Y DLP UNIT Y |
| Парткод: | 2D993060 |
| Деталь: | DV-502Y DLP UNIT Y |
| Парткод: | 2D993270 |
| Деталь: | DV-500M DLP UNIT M |
| Парткод: | 2D993070 |
| Деталь: | DV-502M DLP UNIT M |
| Парткод: | 2D993280 |
| Деталь: | DV-500C DLP UNIT C |
| Парткод: | 2D993080 |
| Деталь: | DV-502C DLP UNIT C |
| Парткод: | 2D993290 |
| Деталь: | PC-60LG(A4) CASSETTE ASSY |
| Парткод: | 5PLPXZ7APKX |
| Деталь: | PC-60LG(LTR) CASSETTE ASSY |
| Парткод: | 5PLPXCUAPKX |
| Деталь: | PC-60LG(A4) CASSETTE ASSY |
| Парткод: | 5PLPXDSAPKX |
| Деталь: | PLATE BOTTOM |
| Парткод: | 5MMX883SD004 |
| Деталь: | Label Operation |
| Парткод: | 5MVVL221GE1H |
| Деталь: | LABEL OPERATION J |
| Парткод: | 5MVVL221GE1J |
| Деталь: | SHEET FRICTION |
| Парткод: | 5MVS421RN004 |
| Деталь: | PLATE SIDE L |
| Парткод: | 5MML877SN002 |
| Деталь: | HOLDER DIAL |
| Парткод: | 5MVX543DH002 |
| Деталь: | DIAL CASSETTE |
| Парткод: | 5MVM586SH001 |
| Деталь: | LABEL SIZE LGL |
| Парткод: | 5MVVL171WN03 |
| Деталь: | LOCK LEVER SIDE |
| Парткод: | 5MVX642DG001 |
| Деталь: | SPRING LOCK GUIDE |
| Парткод: | 5MMW166LD010 |
| Деталь: | EARTH PLATE |
| Парткод: | 5MMX653LD004 |
| Деталь: | LOCK BOTTOM |
| Парткод: | 5MVX432DN005 |
| Деталь: | SP STOPPER BOTTOM |
| Парткод: | 5MMW251LD048 |
| Деталь: | GEAR CASSETTE |
| Парткод: | 5MVG127DB046 |
| Деталь: | SPRING FEED L |
| Парткод: | 5MMW161LD045 |
| Деталь: | BUSH4 |
| Парткод: | 5MVM164DN007 |
| Деталь: | Roller feed |
| Парткод: | 5MVT774DN001 |
| Деталь: | SPRING FEED R |
| Парткод: | 5MMW161LD044 |
| Деталь: | SPRING BOTTOM EARTH |
| Парткод: | 5MMW682LD005 |
| Деталь: | SPRING BOTTOM EARTH |
| Парткод: | 5MMW682LD007 |
| Деталь: | SPRING END |
| Парткод: | 5MMW151SD003 |
| Деталь: | END FENCE |
| Парткод: | 5MVX664DN001 |
| Деталь: | LOCK LEVER END |
| Парткод: | 5MVX642DG002 |
| Деталь: | PLATE SIDE R |
| Парткод: | 5MML877SN001 |
| Деталь: | SPRING BOTTOM |
| Парткод: | 5MMW682LD004 |
| Деталь: | SPRING BOTTOM |
| Парткод: | 5MMW682LD006 |
| Деталь: | LEVER INDICATOR |
| Парткод: | 5MVX764DN001 |
| Деталь: | INDICATER PAPER |
| Парткод: | 5MVX422SD002 |
| Деталь: | BASE CASSETTE LGL |
| Парткод: | 5MVB987SH018 |
| Деталь: | COVER ROLLER |
| Парткод: | 5MVX853SH003 |
| Деталь: | SPRING RETARD |
| Парткод: | 5MMW151LD004 |
| Деталь: | HOLDER RETARD |
| Парткод: | 5MVX644DN001 |
| Деталь: | GUIDE RETARD |
| Парткод: | 5MVX632SH005 |
| Деталь: | RETARD ROLL ASSY |
| Парткод: | 5AAVR0LL+052 |
| Деталь: | LK-500 LED HEAD UNIT |
| Парткод: | 2D993200 |
| Деталь: | DK-500 DRUM UNIT |
| Парткод: | 2D993040 |
| Деталь: | MC-500 MCH ASSY |
| Парткод: | 2D993160 |
| Деталь: | SPRING LOCK L |
| Парткод: | 2D908360 |
| Деталь: | LEVER DRUM L |
| Парткод: | 2D908340 |
| Деталь: | SPRING EARTH |
| Парткод: | 2D908380 |
| Деталь: | LEVER DRUM R |
| Парткод: | 2D908350 |
| Деталь: | SPRING LOCK R |
| Парткод: | 2D908370 |
| Деталь: | COVER TOP ASSY |
| Парткод: | 2D969100 |
| Деталь: | COVER TOP |
| Парткод: | 2D904010 |
| Деталь: | SPRING PULLEY |
| Парткод: | 5MMW251LD046 |
| Деталь: | ROLLER PINCH |
| Парткод: | 5MVM273DB006 |
| Деталь: | ACTUATOR FD |
| Парткод: | 5MVX732CB003 |
| Деталь: | FRAME FD |
| Парткод: | 5MVX852CH002 |
| Деталь: | GUIDE STOCK |
| Парткод: | 2D904170 |
| Деталь: | ROLLER FD |
| Парткод: | 2D904090 |
| Деталь: | FRAME FD LOW |
| Парткод: | 2D904060 |
| Деталь: | BUSH FD |
| Парткод: | 5MVM266DN006 |
| Деталь: | SPRING FRAME FD LOW |
| Парткод: | 2D902570 |
| Деталь: | DISCHARGER FD |
| Парткод: | 2D904250 |
| Деталь: | GEAR ROLL FD Z18 |
| Парткод: | 5MVG127DN076 |
| Деталь: | COVER LEFT ASSY |
| Парткод: | 2D969110 |
| Деталь: | COVER SIDE |
| Парткод: | 2D904040 |
| Деталь: | KEY BOARD ASSY |
| Парткод: | 2D968530 |
| Деталь: | KEY BOARD ASSY |
| Парткод: | 2D969250 |
| Деталь: | KEY BOARD ASSY |
| Парткод: | 2D969260 |
| Деталь: | COVER PANEL E |
| Парткод: | 2D924060 |
| Деталь: | COVER PANEL FRENCH |
| Парткод: | 2D904100 |
| Деталь: | COVER OABEL ITALIAN |
| Парткод: | 2D904110 |
| Деталь: | COVER FRONT |
| Парткод: | 5MVB866CH022 |
| Деталь: | COVER RIGHT ASSY |
| Парткод: | 2D969120 |
| Деталь: | COVER REAR |
| Парткод: | 2D904050 |
| Деталь: | FK-500(E) FUSER UNIT 230V |
| Парткод: | 2D993150 |
| Деталь: | FK-500(U) FUSER UNIT 120V |
| Парткод: | 2D993220 |
| Деталь: | SPRING PRESS |
| Парткод: | 2D920250 |
| Деталь: | FRAME FUSER UP |
| Парткод: | 2D920320 |
| Деталь: | THERMISTOR ASSY |
| Парткод: | 2D927090 |
| Деталь: | THERMOSTAT 250V150C |
| Парткод: | YF0A1530 |
| Деталь: | PLATE RELEASE L |
| Парткод: | 2D920190 |
| Деталь: | PLATE RELEASE R |
| Парткод: | 2D920200 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926130 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926140 |
| Деталь: | PLATE PRESS L |
| Парткод: | 2D920170 |
| Деталь: | PLATE PRESS R |
| Парткод: | 2D920180 |
| Деталь: | ROLLER FIX UP |
| Парткод: | 2D920060 |
| Деталь: | ROLLER FIX LOW |
| Парткод: | 2D920070 |
| Деталь: | GUIDE CHANGE |
| Парткод: | 2D920140 |
| Деталь: | ACTUATOR FUSER |
| Парткод: | 2D920150 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 2D920280 |
| Деталь: | SPRING PULLEY EXIT |
| Парткод: | 2D920300 |
| Деталь: | LABEL EXIT |
| Парткод: | 2D920390 |
| Деталь: | GUIDE EXIT |
| Парткод: | 2D920080 |
| Деталь: | BUSH FD |
| Парткод: | 5MVM266DN006 |
| Деталь: | GEAR IDLE Z18 |
| Парткод: | 5MVG127DN047 |
| Деталь: | GEAR EXIT Z15S |
| Парткод: | 2D920040 |
| Деталь: | SPRING EXIT R |
| Парткод: | 2D920270 |
| Деталь: | SPRING EXIT L |
| Парткод: | 2D920260 |
| Деталь: | SHAFT EXIT |
| Парткод: | 5MMT722SZ001 |
| Деталь: | PULLEY EXIT |
| Парткод: | 5MVM176DB018 |
| Деталь: | ROLLER EXIT |
| Парткод: | 2D920340 |
| Деталь: | COVER FUSER R |
| Парткод: | 2D920120 |
| Деталь: | GEAR JOINT Z36 |
| Парткод: | 5MVG148XN005 |
| Деталь: | SEAL HEATER R |
| Парткод: | 2D920360 |
| Деталь: | Ring Stop |
| Парткод: | 2D920310 |
| Деталь: | GEAR HEAT Z43S |
| Парткод: | 2D920020 |
| Деталь: | BUSH FUSER |
| Парткод: | 2D920030 |
| Деталь: | FUSER BEARING |
| Парткод: | 2D920350 |
| Деталь: | COVER FUSER LOW |
| Парткод: | 2D920130 |
| Деталь: | GUIDE ENTRANCE LOW |
| Парткод: | 2D920330 |
| Деталь: | PLATE STAY |
| Парткод: | 2D920210 |
| Деталь: | LAMP HEATER UP 240V |
| Парткод: | WP0A0510 |
| Деталь: | LAMP HEATER UP 120V |
| Парткод: | WP0A0530 |
| Деталь: | LAMP HEATER LOW 240V |
| Парткод: | WP0A0520 |
| Деталь: | LAMP HEATER LOW 120V |
| Парткод: | WP0A0540 |
| Деталь: | COVER FUSER L |
| Парткод: | 2D920110 |
| Деталь: | STUD SCREW M3 |
| Парткод: | 5MMT143SZ014 |
| Деталь: | SOLENOID |
| Парткод: | WSAA0170 |
| Деталь: | ACTUATOR SOL |
| Парткод: | 2D920010 |
| Деталь: | SPRING PIN |
| Парткод: | 5MBP2518WXSP |
| Деталь: | RUBBER PIN |
| Парткод: | 5MVM111 RB002 |
| Деталь: | P.W.B.ASSY KP-970 |
| Парткод: | 2D901460 |
| Деталь: | NUT FUSER A |
| Парткод: | 5MMS111SL002 |
| Деталь: | PLATE HEATER L |
| Парткод: | 2D920220 |
| Деталь: | SPRING SOL |
| Парткод: | 5MMW261LJ032 |
| Деталь: | FRAME FUSER |
| Парткод: | 2D920050 |
| Деталь: | FE-500 FEED TRANS UNIT |
| Парткод: | 2D993140 |
| Деталь: | BASE FEED |
| Парткод: | 2D916050 |
| Деталь: | GUIDE PAPER |
| Парткод: | 2D916070 |
| Деталь: | SHEET REGIST |
| Парткод: | 2D916150 |
| Деталь: | PAPER CHUTE |
| Парткод: | 2D916080 |
| Деталь: | DISCHARGER ASSY |
| Парткод: | 2D968830 |
| Деталь: | ROLLER TRANSFER ASSY |
| Парткод: | 2D968840 |
| Деталь: | BUSH TRANSFER |
| Парткод: | 5MVX322DB019 |
| Деталь: | SPRING TRANS |
| Парткод: | 2D916060 |
| Деталь: | ROLLER REGIST UP |
| Парткод: | 2D916170 |
| Деталь: | SPRING REGIST L |
| Парткод: | 2D916250 |
| Деталь: | SPRING REGIST R |
| Парткод: | 5MMW341LD008 |
| Деталь: | BUSH REGIST |
| Парткод: | 5MVM221 DB002 |
| Деталь: | GEAR REGIST Z19S |
| Парткод: | 5MVG126DN015 |
| Деталь: | ROLLER REGIST LOW |
| Парткод: | 2D916180 |
| Деталь: | BUSH POM A |
| Парткод: | 5MVM176DN019 |
| Деталь: | SPRING EARTH B |
| Парткод: | 2D916130 |
| Деталь: | PLATE EARTH TC |
| Парткод: | 2D916110 |
| Деталь: | M.GLAZE R. 100M 1W |
| Парткод: | RH0A0040 |
| Деталь: | SPRING TRANS R |
| Парткод: | 5MMW241SX005 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 2D916210 |
| Деталь: | PLATE EARTH MP |
| Парткод: | 2D916140 |
| Деталь: | SPRING ACTUATOR REG |
| Парткод: | 2D916260 |
| Деталь: | SENSOR DOC |
| Парткод: | 5MVX742SB008 |
| Деталь: | ACTUATOR PAPER |
| Парткод: | 5MVX663SB013 |
| Деталь: | GEAR REG Z22S-Z32S |
| Парткод: | 5MVG148DN060 |
| Деталь: | GEAR IDLE Z23S |
| Парткод: | 2D916220 |
| Деталь: | HOOK RELEASE |
| Парткод: | 2D916090 |
| Деталь: | SPRING LOCK R |
| Парткод: | 5MMW251SD002 |
| Деталь: | LEVER LOCK |
| Парткод: | 5MVX666SH005 |
| Деталь: | GEAR JOINT Z26S |
| Парткод: | 2D916230 |
| Деталь: | BUSH FEED |
| Парткод: | 5MVM222XN001 |
| Деталь: | ROLLER GUIDE ASSY |
| Парткод: | 5AAVR0LL+049 |
| Деталь: | SHAFT RELEASE |
| Парткод: | 5MVX843CB004 |
| Деталь: | SHAFT ROLL GUIDE |
| Парткод: | 5MMT860SN002 |
| Деталь: | SPRING EARTH C |
| Парткод: | 2D916270 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926390 |
| Деталь: | WIRE EARTH M/P |
| Парткод: | 2D916280 |
| Деталь: | HOLDER FEED ASSY |
| Парткод: | 5AAYA37E++35 |
| Цена: | 6 700 ₽ |
| Деталь: | COVER BKTFEED |
| Парткод: | 5MVX642DH001 |
| Деталь: | GEAR FEED IDLEZ29S |
| Парткод: | 5MVG137DN036 |
| Деталь: | GEAR PICKUP |
| Парткод: | 5AAVGEAR+037 |
| Деталь: | ROLLER FEED ASSY |
| Парткод: | 5AAVR0LL+047 |
| Цена: | 1 000 ₽ |
| Деталь: | SHAFT PICKUP |
| Парткод: | 5MMT664SN002 |
| Деталь: | ROLLER PICKUP ASSY |
| Парткод: | 5AAVR0LL+048 |
| Цена: | 1 000 ₽ |
| Деталь: | BRACKET FEED |
| Парткод: | 5MVX664SH004 |
| Деталь: | HOLDER RELEASE |
| Парткод: | 5MVX376DN001 |
| Деталь: | TRAY M/P ASSY |
| Парткод: | 2D969170 |
| Деталь: | COVER M/P |
| Парткод: | 2D906020 |
| Деталь: | TRAY M/P |
| Парткод: | 2D906010 |
| Деталь: | BASE M/P |
| Парткод: | 5MVB864SH009 |
| Деталь: | GEAR MANUAL |
| Парткод: | 5MVG127DH001 |
| Деталь: | SPRING LOCK M/P |
| Парткод: | 5MMW261SM001 |
| Деталь: | GUIDE M/P L |
| Парткод: | 2D906030 |
| Деталь: | GUIDE M/P R |
| Парткод: | 2D906040 |
| Деталь: | SPRING SEPARATOR |
| Парткод: | 5MMW261LD039 |
| Деталь: | SEPARATOR M/P ASSY |
| Парткод: | 5AAVCASET248 |
| Деталь: | SP BOTTOM M/P L |
| Парткод: | 2D916020 |
| Деталь: | SP BOTTOM M/P R |
| Парткод: | 5MMW461SD004 |
| Деталь: | BOTTOM MULTI ASSY |
| Парткод: | 5AAVCASET249 |
| Деталь: | BRACKET BOTTOM |
| Парткод: | 5MVX533DN002 |
| Деталь: | LID CONTROLLER |
| Парткод: | 2D903020 |
| Деталь: | PLATE OPTION |
| Парткод: | 5MMS636SD009 |
| Деталь: | PANEL REAR |
| Парткод: | 2D903030 |
| Деталь: | SCREW OP |
| Парткод: | 5MMT263SN012 |
| Деталь: | P.W.B.ASSY KP-893 |
| Парткод: | 2D901620 |
| Деталь: | RAIL OPTION |
| Парткод: | 2D903070 |
| Деталь: | P.W.B.ASSY KP-957 |
| Парткод: | 2D901200 |
| Деталь: | BOX CONTROLLER |
| Парткод: | 2D903010 |
| Деталь: | FOOT |
| Парткод: | 5MVX221RB014 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926030 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926020 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926070 |
| Деталь: | FAN MOTOR |
| Парткод: | WNA00580 |
| Деталь: | CASE PWB POWER |
| Парткод: | 2D903050 |
| Деталь: | CONN. CORD ASSY |
| Парткод: | 2D926090 |
| Деталь: | SWITCHING REGULATOR |
| Парткод: | 2D928610 |
| Деталь: | SWITCHING REGULATOR |
| Парткод: | 2D928600 |
| Деталь: | ROD SW POWER |
| Парткод: | 2D903060 |
| Деталь: | BRACKET BOX |
| Парткод: | 2D903040 |
| Деталь: | P.W.B.ASSY KP-1054 |
| Парткод: | 2D901720 |
| Деталь: | P.W.B.ASSY KP-1054 |
| Парткод: | 2D901730 |
| Деталь: | LEVER SW |
| Парткод: | 5MVX433SH002 |
Коды ошибок
0100
0150
0420
0460
0951
0952
0953
0954
1200
2610
2620
2630
5301
5302
5303
5304
6000
6020
6030
6100
6120
6130
6400
7001
7002
7003
7004
7401
7402
7403
7404
7411
7412
7413
7414
7600
F000
F010
F020
F030
F040
F050
m1
m2
m3
m4
m5
m6
m7
Описание
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0420 |
| Description: | Paper feeder communication error Communication error between control PWB and optional paper feeder. |
| Causes: | Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF main-PWB. |
| Remedy: | Improper installation paper feeder. Follow installation instruction carefully again. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective control PWB. Replace the control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder). Defective PF main- PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 0460 |
| Description: | Communication error between printer and duplex unit • The CPU (U2) of engine controller PWB (KP-992) does not communicate with the PD-800 duplex unit normally. |
| Causes: | Defective engine controller PWB (KP-992). Defective main board of PD-800 duplex unit. Defective paper feeder/options relay PWB (KP- 995). Defective connection printer and PD-800 duplex unit. Defective harness (2CK2719) between engine controller PWB (KP-992) and paper feeder/ options relay PWB (KP-995), or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the main board of duplex unit PD- 30. See PD-800 duplex unit’s service manual. Replace the paper feeder/options relay PWB (KP-995). Reinstall PD-800 duplex unit. Check the continuity of the harness (2CK2719). Check the insertion of connectors. |
| Error code: | 0951 |
| Description: | LED print head 4 (EEPROM) communication error [black drum unit] The LED print head 4 (EEPROM) of the black drum unit does not communicate with the engine controller PWB (A0004) normally. The incompatible LED print head is installed to the printer. |
| Causes: | Defective LED print head 4. Installing the LED print head, which is incompatible with the printer specification. Defective engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Defective FFCs (S03011) between LED print head 4 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals.D |
| Remedy: | Defective LED print head 4. Replace the LED print head 4. See page 1- 5-15. Installing the LED print head, which is incompatible with the printer specification. Install the compatible LED print head to the black drum unit. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Replace the LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Check the continuity of the harness (S03214), check the insertion of YC3 of the engine controller PWB (A0004), if there is trouble, remedy or replace. Defective FFCs (S03011) between LED print head 4 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. Check the connection of the FFCs with the black drum unit and the printer main unit, check the continuity of the FFCs (S03011), check the connection of the LED print head 4, if there is trouble, remedy or replace. |
| Error code: | 0952 |
| Description: | LED print head 2 (EEPROM) communication error [cyan drum unit] The LED print head 2 (EEPROM) of the cyan drum unit does not communicate with the engine controller PWB (A0004) normally. |
| Causes: | Defective LED print head 2. Installing the LED print head, which is incompatible with the printer specification. Defective engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Defective FFCs (S03011) between LED print head 2 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. |
| Remedy: | Defective LED print head 2. Replace the LED print head 2. See page 1- 5-15. Installing the LED print head, which is incompatible with the printer specification. Install the compatible LED print head to the black drum unit. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Replace the LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Check the continuity of the harness (S03214), check the insertion of YC3 of the engine controller PWB (A0004), if there is trouble, remedy or replace. Defective FFCs (S03011) between LED print head 2 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. Check the connection of the FFCs with the cyan drum unit and the printer main unit, check the continuity of the FFCs (S03011), check the connection of the LED print head 2, if there is trouble, remedy or replace. |
| Error code: | 0953 |
| Description: | LED print head 1 (EEPROM) communication error [magenta drum The LED print head 1 (EEPROM) the magenta drum unit does communicate with the engine controller PWB (A0004) normally. |
| Causes: | Defective LED print head 1. Installing the LED print head, which is incompatible with the printer specification. Defective engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Defective FFCs (S03011) between LED print head 1 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. |
| Remedy: | Defective LED print head 1. Replace the LED print head 1. See page 1- 5-15. Installing the LED print head, which is incompatible with the printer specification. Install the compatible LED print head to the black drum unit. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Replace the LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Check the continuity of the harness (S03214), check the insertion of YC3 of the engine controller PWB (A0004), if there is trouble, remedy or replace. Defective FFCs (S03011) between LED print head 1 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. Check the connection of the FFCs with the magenta drum unit and the printer main unit, check the continuity of the FFCs (S03011), check the connection of the LED print head 1, if there is trouble, remedy or replace. |
| Error code: | 0954 |
| Description: | LED print head 3 (EEPROM) communication error [yellow drum unit] The LED print head 3 (EEPROM) of the yellow drum unit does not communicate with the engine controller PWB (A0004) normally. |
| Causes: | Defective LED print head 3. Installing the LED print head, which is incompatible with the printer specification. Defective engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Defective FFCs (S03011) between LED print head 3 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. |
| Remedy: | Defective LED print head 3. Replace the LED print head 3. See page 1- 5-15. Installing the LED print head, which is incompatible with the printer specification. Install the compatible LED print head to the black drum unit. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective LED print heads relay PWB (A0176). Replace the LED print heads relay PWB (A0176). Defective harness (S03214) between engine controller PWB (A0004) and LED print heads relay PWB (A0176), or poor contact of the connector terminals. Check the continuity of the harness (S03214), check the insertion of YC3 of the engine controller PWB (A0004), if there is trouble, remedy or replace. Defective FFCs (S03011) between LED print head 3 and LED print heads relay PWB (A0176), or poor contact of the FFC terminals. Check the connection of the FFCs with the magenta drum unit and the printer main unit, check the continuity of the FFCs (S03011), check the connection of the LED print head 3, if there is trouble, remedy or replace. |
| Error code: | 1200 |
| Description: | Side registration motor error The duplexer PWB of the optional duplexer cannot detect the home position of the adjust guide. |
| Causes: | Defective duplexer. Defective engine controller PWB (A0004). |
| Remedy: | Defective duplexer. Refer to the duplexer`s service manual. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). |
| Error code: | 2610 |
| Description: | PF paper feed motor error (paper feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 2PF - Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2620 |
| Description: | PF drive motor 3 error (PF3) During the motor drive, the stable signal is not turned on for continuous 5 s. |
| Remedy: | Defective connector cable or poor contact in the connector 1. Reinsert the connector. 2. Check continuity within the connector wire. If none, replace the wire. PF drive motor 3 and PF main PWB (YC6) Drive transmission system for the PF drive motor 1. Check if the rollers and gears rotate smoothly. If not, clean or grease the bushes and gears. 2. Replace the gears, if damaged. PF drive motor Replace the PF drive motor 3. PF main PWB Replace the PF main PWB. |
| Error code: | 2630 |
| Description: | Paper feed motor error (bottom) The notification that was received, the motor clock sensor cannot detect the revolution of the paper feed motor of the optional paper feeder (third). |
| Causes: | Defective paper feeder. Defective engine controller PWB (A0004). |
| Remedy: | Defective paper feeder. Refer to the paper feeder`s service manual. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). |
| Error code: | 5301 |
| Description: | Broken cleaning lamp K wire When the cleaning lamp K is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit K and Drum relay PWB (YC2) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp K. Replace the drum unit K. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5302 |
| Description: | Broken cleaning lamp C wire When the cleaning lamp C is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp C. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit C and Drum relay PWB (YC4) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp C. Replace the drum unit C. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5303 |
| Description: | Broken cleaning lamp M wire When the cleaning lamp M is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp M. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit M and Drum relay PWB (YC3) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp M. Replace the drum unit M. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5304 |
| Description: | Broken cleaning lamp Y wire When the cleaning lamp Y is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp Y. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit Y and Drum relay PWB (YC5) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp Y. Replace the drum unit Y. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6100 |
| Description: | Broken fuser heater wire Fuser thermistor 5 won’t reach the reference temperature in 480 s after shifting to low power mode. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6120 |
| Description: | Abnormally high fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature higher than 190°C/ 374°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 5. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6130 |
| Description: | Broken fuser press thermistor 5 wire The input from the fuser press thermistor 5 has been less than 30°C/ 86°F (A/D: greater thann992) for 60 seconds continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) Fuser IH PWB(YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 7001 |
| Description: | Toner motor error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB. |
| Remedy: | Toner container 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7002 |
| Description: | Toner motor C error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor C. Defective toner motor C. Defective engine PWB. |
| Remedy: | Toner container C 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Screw sensor C 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor C and Engine PWB (YC27) 3. Replace the screw sensor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7003 |
| Description: | Toner motor M error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor M. Defective toner motor M. Defective engine PWB. |
| Remedy: | Toner container M 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Screw sensor M 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor M and Engine PWB (YC27) 3. Replace the screw sensor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7004 |
| Description: | Toner motor Y error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor Y. Defective toner motor Y. Defective engine PWB. |
| Remedy: | Toner container Y 1. Check that the spiral screw of the toner container can be rotated by the hand. 1. Check for broken gears and replace if any. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Screw sensor Y 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor Y and Engine PWB (YC27) 3. Replace the screw sensor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7401 |
| Description: | Developer unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Different type of the developer unit is installed. Install the developer unit of the correct type. Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7402 |
| Description: | Developer unit C type mismatch error Absence of the developer unit C is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit C and front PWB (YC13) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7403 |
| Description: | Developer unit M type mismatch error Absence of the developer unit M is detected. |
| Causes: | Defective connector cable or poor contact in the connector Different type of the developer unit is installed |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit M and front PWB (YC11) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7404 |
| Description: | Developer unit Y type mismatch error Absence of the developer unit Y is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit Y and front PWB (YC15) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7411 |
| Description: | Drum unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the drum unit is installed. |
| Remedy: | Different type of the drum unit is installed. Install the drum unit of the correct type. Drum unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum unit and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7412 |
| Description: | Drum unit type Mismatch error (Cyan) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit C |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7413 |
| Description: | Drum unit type Mismatch error (Magenta) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit M |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7414 |
| Description: | Drum unit type Mismatch error (Yellow) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit Y |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7600 |
| Description: | Toner ID sensor error The detection signal of the toner ID sensor was abnormal value. |
| Causes: | Defective toner ID sensor. Defective engine controller PWB (A0004). Defective harness (S03195) between engine controller PWB (A0004) and toner ID sensor or poor contact of the connector terminals. |
| Remedy: | Defective toner ID sensor. Replace the toner ID sensor. Defective engine controller PWB (A0004). Replace the engine controller PWB (A0004). Defective harness (S03195) between engine controller PWB (A0004) and toner ID sensor or poor contact of the connector terminals. Check the continuity of the harness (S03195), check the connection YC11 connector of the engine controller PWB (A0004), if there is trouble, remedy or replace. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F030 |
| Description: | Main PWB system error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | m1 |
| Description: | "Close top cover" display is not cancelled to closing the top cover. |
| Remedy: | Right edge of the top cover floating, it is not closed completely. Close the top cover securely. Defective top cover switch 2. Replace the top cover switch 2. Defective top cover/paper feed unit switch (SW701) of the sensor PWB (KP-982). Replace the sensor PWB (KP-982). Defective harness (S02846) between engine controller PWB (KP-1054) and top cover switch 2 or poor contact of the connector terminals. Check the continuity of the harness (S02846), check the connection YC11 connector of the engine controller PWB (KP-1054), if there is trouble, remedy or replace. Malfunctioning interlock rod that interfaces between the top cover and the top cover/ paper feed unit switch (SW701). Check to see if the interlock rod malfunctions. If it malfunctions, repair it. Defective engine controller PWB (KP-1054). Replace the engine controller PWB (KP-1054). Defective harness (S02849) between engine controller PWB (KP-1054) and sensor PWB (KP-982) or poor contact of the connector terminals. Check the continuity of the harness (S02849), check the connection YC2 connector of the engine controller PWB (KP-1054), check the connection YC701 and YC702 connectors of the sensor PWB (KP-982), if there is trouble, remedy or replace. |
| Error code: | m2 |
| Description: | "Close side cover" display is not cancelled to closing the top cover. |
| Remedy: | Defective side cover switch (SW702) of the sensor PWB (KP-982). Replace the sensor PWB (KP-982). The actuator of the side cover switch (SW702) of the sensor PWB (KP-982) is bent. Check the bending of the actuator of the side cover switch, if there is trouble, remedy or replace. Defective sensor PWB (KP- 982). Replace the sensor PWB (KP-982). Defective engine controller PWB (KP-1054). Replace the engine controller PWB (KP-1054). Defective harness (S02849) between engine controller PWB (KP-1054) and sensor PWB (KP-982) or poor contact of the connector terminals. Check the continuity of the harness (S02849), check the connection YC2 connector of the engine controller PWB (KP-1054), check the connection YC701 and YC702 connectors of the sensor PWB (KP-982), if there is trouble, remedy or replace. |
| Error code: | m3 |
| Description: | "Close paper transfer unit" display is not cancelled to closing the paper feed unit. |
| Remedy: | Defective top cover/paper feed unit switch (SW701) of the sensor PWB (KP-982). Replace the sensor PWB (KP-982). Malfunctioning interlock rod that interfaces between the top cover and the top cover/ paper feed unit switch (SW701). Check to see if the interlock rod malfunctions. If it malfunctions, repair it. Defective engine controller PWB (KP-1054). Replace the engine controller PWB (KP-1054). Defective harness (S02849) between engine controller PWB (KP-1054) and sensor PWB (KP-982) or poor contact of the connector terminals. Check the continuity of the harness (S02849), check the connection YC2 connector of the engine controller PWB (KP-1054), check the connection YC701 and YC702 connectors of the sensor PWB (KP-982), if there is trouble, remedy or replace. |
| Error code: | m4 |
| Description: | "Cassette 1 not loaded" display is not cancelled to closing the paper cassette. |
| Remedy: | Defective cassette size switch. Replace the cassette size switch. Defective sensor PWB (KP- 982). Replace the sensor PWB (KP-982). Defective harness (S02861) between cassette size switch and sensor PWB (KP-982) or poor contact of the connector terminals. Check the continuity of the harness (S02861), check the connection YC703 connector of sensor PWB (KP-982), if there is trouble, remedy or replace. Defective harness (S02849) between engine controller PWB (KP-1054) and sensor PWB (KP-982) or poor contact of the connector terminals. Check the continuity of the harness (S02849), check the connection YC2 connector of the engine controller PWB (KP-1054), check the connection YC701 and YC702 connectors of the sensor PWB (KP-982), if there is trouble, remedy or replace. Defective engine controller PWB (KP-1054). Replace the engine controller PWB (KP-1054). |
| Error code: | m5 |
| Description: | "Check waste toner box" display is not cancelled to replacing the waste toner box. |
| Remedy: | The waste toner full sensor or the waste toner full sensor [PWB] (KP-974) the sensor section is dirty. Replace the waste toner full sensor or the waste toner full sensor [PWB] (KP-974). Defective harness (S02863) between bias high voltage PWB (KP-980) and waste toner full sensor [PWB] (KP-974) or poor contact of the connector terminals. Check the continuity of the harness (S02863), check the connection of YC802 connector of the bias high voltage PWB (KP-980), check the connection of YC682 connector of the waste toner full sensor [PWB] (KP-974) if there is trouble, remedy or replace. Defective harness (S02862) between waste toner full sensor and waste toner full sensor [PWB] (KP-974) or poor contact of the connector terminals. Check the continuity of the harness (S02862), check the connection YC681 connector of the waste toner full sensor [PWB] (KP- 974), if there is trouble, remedy or replace. Defective engine controller PWB (KP-1054). Replace the engine controller PWB (KP-1054). |
| Error code: | m6 |
| Description: | The paper size is not recognized as the size set with the paper size dial. |
| Remedy: | Defective cassette size switch. Replace the cassette size switch. Defective sensor PWB (KP- 982). Replace the sensor PWB (KP-982). Defective harness (S02861) between cassette size switch and sensor PWB (KP-982) or poor contact of the connector terminals. Check the continuity of the harness (S02861), check the connection YC703 connector of sensor PWB (KP-982), if there is trouble, remedy or replace. Defective engine controller PWB (KP-1054). Replace the engine controller PWB (KP-1054). |
| Error code: | m7 |
| Description: | Paper misfeed display is not cancelled. |
| Remedy: | Defective registration sensor. Replace the sensor PWB (KP-982). Defective sensor PWB (KP- 982). Replace the sensor PWB (KP-982). Defective harness (S02849) between engine controller PWB (KP-1054) and sensor PWB (KP-982) or poor contact of the connector terminals. Check the continuity of the harness (S02849), check the connection YC2 connector of the engine controller PWB (KP-1054), check the connection YC701 and YC702 connectors of the sensor PWB (KP-982), if there is trouble, remedy or replace. Defective exit sensor. Replace the fuser PWB (KP-970). Defective harness (S02849) between fuser PWB (KP- 970) and fuser connector or poor contact of the connector terminals. Check the continuity of the harness (S02849), check the connection YC691 connector of the fuser PWB (KP-970), if there is trouble, remedy or replace. Defective harness (S02853) between power supply PWB and fuser connector or poor contact of the connector terminals. Check the continuity of the harness (S02853), check the connection YC902 connector of the power supply PWB, if there is trouble, remedy or replace. Defective engine controller PWB (KP-1054). Replace the engine controller PWB (KP-1054). Defective power supply PWB. Replace the power supply PWB. |
Название
Kyocera Блок фотобарабана
Kyocera Блок проявки голубой
Kyocera Блок проявки черный
Kyocera Блок проявки пурпурный
Kyocera Блок проявки желтый
Kyocera Узел термозакрепления 230v
Kyocera Сервисный комплект
Kyocera Тонер-картридж голубой
Kyocera Тонер-картридж черный
Kyocera Тонер-картридж пурпурный
Kyocera Тонер-картридж желтый
