Kyocera FS-C8008N
Рейтинг
Снят с производства
Тип устройства
Принтер
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
100000
Скорость печати
A4
31
Цветность печати
цветная
Общие характеристики |
|
|---|---|
Цветность печати |
цветная |
Число страниц в месяц |
100 000 |
Макс. формат |
A3 |
Область применения |
большой офис |
Сканер |
|
Печать фотографий |
|
Копир |
|
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Тип устройства |
Принтер |
Принтер |
|
Прямая печать |
|
Двусторонняя печать |
|
Макс, разрешение для ч/б печати |
|
| По Y | 600 |
| По X | 600 |
Скорость ч/б печати |
|
| A4 | 31 |
Скорость цветной печати |
|
| A4 | 8 |
Сканер |
|
Стандарт WIA |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Расходные материалы |
|
Ресурс цветного картриджа/тонера |
10 000 |
Ресурс ч/б картриджа/тонера |
25 000 |
Печать на: |
|
| Этикетках |
|
| Фотобумаге |
|
| Пленках |
|
Языки управления |
|
| PostScript |
|
Лотки |
|
Подача бумаги |
|
| Стандартная | 1 150 |
Вывод бумаги |
|
| Стандартный | 650 |
Интерфейсы |
|
Инфракрасный порт |
|
USB |
|
Ethernet (RJ-45) |
|
LPT |
|
Память/Процессор |
|
Макс, объем памяти |
256 |
Объем памяти |
128 |
Дополнительная информация |
|
Поддержка ОС |
|
| Windows |
|
| DOS |
|
| Mac OS |
|
| Linux |
|
Уровень шума |
|
| При работе | 53 |
Габариты |
|
Ширина |
590 |
Вес |
95 |
Глубина |
585 |
Высота |
673 |
Модули
MP TRAY
Face-down Unit
Upper Frame Unit
Upper Frame Unit 2
Developer Unit - K
Developer Unit - Y
Electrical Parts 2
PAPER FEED UNIT
Drive unit
Electrical Parts
Drive Unit 2
FUSER UNIT
Primary Transfer Unit
Developer Unit - C
Exterior Covers
Developer Unit - M
Drum Unit
Controller Box
Детали Electrical Parts 2
| Деталь: | COVER RIGHT MPF ASSY |
| Парткод: | 2CK68060 |
| Деталь: | COVER RIGHT MPF |
| Парткод: | 2BM07102 |
| Деталь: | LOCK COVER MPF |
| Парткод: | 2BM07130 |
| Деталь: | SPRING LOCK MPF |
| Парткод: | 2BM07140 |
| Деталь: | TRAY EXTENSION MPF |
| Парткод: | 2BM07121 |
| Деталь: | LABEL MPF |
| Парткод: | 2BM07370 |
| Деталь: | Label Size |
| Парткод: | 2BM07350 |
| Деталь: | PLATE BOTTOM MPF ASSY |
| Парткод: | 2BM68140 |
| Деталь: | PLATE BOTTOM A |
| Парткод: | 2BM07150 |
| Деталь: | PAD FRICTION |
| Парткод: | 2BM07170 |
| Деталь: | GUIDE PAPER SIDE F |
| Парткод: | 2BM07200 |
| Деталь: | GUIDE PAPER SIDE R |
| Парткод: | 2BM07180 |
| Деталь: | GEAR GUIDE SIDE |
| Парткод: | 2BM07310 |
| Деталь: | HOLDER GUIDE SIDE |
| Парткод: | 2BM07210 |
| Деталь: | PLATE BOTTOM B |
| Парткод: | 2BM07160 |
| Деталь: | GUIDE PAPER MPF |
| Парткод: | 2BM07020 |
| Деталь: | ACTUATOR CAM MPF |
| Парткод: | 2BM07050 |
| Деталь: | RETARD ROLL ASSY |
| Парткод: | 2BM07340 |
| Деталь: | SPRING RETARD MPF |
| Парткод: | 2BM07290 |
| Деталь: | STAY RIGHT MPF |
| Парткод: | 2BM07090 |
| Деталь: | PLATE EARTH MPF |
| Парткод: | 2BM07070 |
| Деталь: | FRAME RIGHT MPF |
| Парткод: | 2BM07011 |
| Деталь: | LABEL MP TRAY |
| Парткод: | 2BM07360 |
| Деталь: | ACTUATOR PAPER MPF |
| Парткод: | 2BM07060 |
| Деталь: | SHAFT ROLL MPF |
| Парткод: | 2BM07260 |
| Деталь: | RING STOPPER |
| Парткод: | 5MVX111 DN003 |
| Деталь: | BUSH POM B |
| Парткод: | 2BM07320 |
| Деталь: | ROLL FEED MPFASSY |
| Парткод: | 2BM07270 |
| Деталь: | CLUTCH MPF ASSY |
| Парткод: | 2BM27120 |
| Деталь: | CLUTCH 26-B |
| Парткод: | 2BM27780 |
| Деталь: | BUSH METAL |
| Парткод: | 2BM07330 |
| Деталь: | PLATE DRIVE MPF ASSY |
| Парткод: | 2BM68150 |
| Деталь: | GEAR MPFZ28Z30 |
| Парткод: | 2BM07240 |
| Деталь: | SHAFT GEAR MPF |
| Парткод: | 2BM07250 |
| Деталь: | HOLDER DRIVE MPF |
| Парткод: | 2BM07230 |
| Деталь: | SOLENOID MPF |
| Парткод: | 2BM27100 |
| Деталь: | PLATE DRIVE MPF |
| Парткод: | 2BM07220 |
| Деталь: | EDGING,ES-0505-2 |
| Парткод: | M2504030 |
| Деталь: | COVER PWB MPF |
| Парткод: | 2BM07030 |
| Деталь: | PT.SENSOR GP2S30 |
| Парткод: | 2BM27170 |
| Деталь: | CONN.CORD P.SIZE ASSY |
| Парткод: | 2BM27140 |
| Деталь: | CONN.CORD MPF ASSY |
| Парткод: | 2BM27130 |
| Деталь: | MPF KP-1015 ASSY |
| Парткод: | 2CK01180 |
| Деталь: | HOLDER CONN.CORD |
| Парткод: | 2CK07510 |
| Деталь: | SEAL CONN.CORD MPF |
| Парткод: | 2CK07520 |
| Деталь: | COVER CONN.CORD MPF |
| Парткод: | 2CK07530 |
| Деталь: | SEAL MPF |
| Парткод: | 2CK07540 |
| Деталь: | BASE TRAY MPF |
| Парткод: | 2CK07550 |
| Деталь: | SEAL CONN.CORD MPF B |
| Парткод: | 2CK07560 |
| Деталь: | CONN.CORD P.LENGTH ASSY |
| Парткод: | 2CK27240 |
| Деталь: | SWITCH BYPASS |
| Парткод: | 2CK27540 |
| Деталь: | LABEL PAPER TYPE E |
| Парткод: | 2CK05080 |
| Деталь: | SPRING BOTTOM MPF |
| Парткод: | 2CK07580 |
| Деталь: | FACE DOWN UNIT |
| Парткод: | 2CK00230 |
| Деталь: | COVER GEAR FD |
| Парткод: | 2BM21031 |
| Деталь: | FCD KP-1022 ASSY |
| Парткод: | 2CK01190 |
| Деталь: | P.W.BOARD KP-809 ASSY |
| Парткод: | 2BM01090 |
| Деталь: | PROTECT BOARD |
| Парткод: | 2BM21600 |
| Деталь: | CONN. CORD F.DOWN-B ASSY |
| Парткод: | 2CK27170 |
| Деталь: | RING STOPPER |
| Парткод: | 5MVX111 DN003 |
| Деталь: | FD FLANGE BELT |
| Парткод: | 2BM21230 |
| Деталь: | BELT FD 264 |
| Парткод: | 2BM21270 |
| Деталь: | FD PULLEY BELT Z18 |
| Парткод: | 2BM21220 |
| Деталь: | FD PULLEY GEAR Z18 |
| Парткод: | 2BM21250 |
| Деталь: | GEAR Z26 |
| Парткод: | 2BM21140 |
| Деталь: | BELT FD 156 |
| Парткод: | 2BM21280 |
| Деталь: | GEAR Z22 |
| Парткод: | 2BM21330 |
| Деталь: | BKT PITCH JOINT |
| Парткод: | 2BM21470 |
| Деталь: | SPRING PLATE JOINT |
| Парткод: | 2BM21420 |
| Деталь: | PIN JOINT |
| Парткод: | 2CK21030 |
| Деталь: | PLATE JOINT |
| Парткод: | 2BM21410 |
| Деталь: | GEAR INPUT Z24 |
| Парткод: | 2BM21340 |
| Деталь: | LOCK COVER FU |
| Парткод: | 2BM21350 |
| Деталь: | FRAME FD |
| Парткод: | 2BM21010 |
| Деталь: | FILM SWITCH |
| Парткод: | 2BM21650 |
| Деталь: | PLATE EARTH SWITCH |
| Парткод: | 2BM21450 |
| Деталь: | PIN IDLE 1 |
| Парткод: | 2CK21040 |
| Деталь: | PIN IDLE 2 |
| Парткод: | 2CK21050 |
| Деталь: | ARM PRESS DLP |
| Парткод: | 2CK21070 |
| Деталь: | PLATE PRESS DLP BASE |
| Парткод: | 2BM21090 |
| Деталь: | FAN FD |
| Парткод: | 2CK21090 |
| Деталь: | COVER CORD FD |
| Парткод: | 2BM21640 |
| Деталь: | GUIDE CHANGE |
| Парткод: | 2BM21080 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | ACTUATOR SENSOR FD |
| Парткод: | 2BM21130 |
| Деталь: | SPRING ACT MIDDLE |
| Парткод: | 2BM21390 |
| Деталь: | ACTUATOR SENSOR FU |
| Парткод: | 2BM21260 |
| Деталь: | SPRING ACT FU |
| Парткод: | 2BM21400 |
| Деталь: | FD PLATE SOLENOID |
| Парткод: | 2BM21040 |
| Деталь: | SOLENOID FD |
| Парткод: | 2BM27800 |
| Деталь: | LEVER SOLENOID |
| Парткод: | 2BM21050 |
| Деталь: | SPRING SOL |
| Парткод: | 5MMW261LJ032 |
| Деталь: | LEVER GUIDE CHANGE |
| Парткод: | 2BM21070 |
| Деталь: | Plate Earth FD |
| Парткод: | 2BM21290 |
| Деталь: | STOPPER PI |
| Парткод: | 2BM17990 |
| Деталь: | ROLLER FD A |
| Парткод: | 2CK21110 |
| Деталь: | KNOB ROLL FD |
| Парткод: | 2BM21440 |
| Деталь: | BUSH DRUM |
| Парткод: | 2BM21210 |
| Деталь: | SPRING EXIT |
| Парткод: | 2BM21530 |
| Деталь: | SPRING EXIT |
| Парткод: | 2BM21480 |
| Деталь: | Bush SP |
| Парткод: | 2BM20610 |
| Деталь: | SHAFT ROLLER FD |
| Парткод: | 2BM21170 |
| Деталь: | PULLEY EXIT A |
| Парткод: | 2BM21160 |
| Деталь: | PULLEY EXIT A |
| Парткод: | 2CK21270 |
| Деталь: | PULLEY B,EJECT |
| Парткод: | 2A621280 |
| Деталь: | BRUSH ERASER |
| Парткод: | 2CK21150 |
| Деталь: | TAPE BRUSH |
| Парткод: | 2BM21620 |
| Деталь: | GUIDE FD |
| Парткод: | 2BM21020 |
| Деталь: | ACTUATOR FULL SENSOR |
| Парткод: | 2BM21150 |
| Деталь: | STAY TOP FD |
| Парткод: | 2BM21240 |
| Деталь: | CONN.CORD P.FULLASSY |
| Парткод: | 2BM27820 |
| Деталь: | CONN.CORD C.SWITCHASSY |
| Парткод: | 2BM27830 |
| Деталь: | SPRING PRESS DLP 1 |
| Парткод: | 2CK21140 |
| Деталь: | SPRING PRESS DLP |
| Парткод: | 2CK21100 |
| Деталь: | ROLLER FD B |
| Парткод: | 2CK21120 |
| Деталь: | COVER FD ASSY |
| Парткод: | 2BM68200 |
| Деталь: | PLATE FDC R |
| Парткод: | 2BM21560 |
| Деталь: | STOPPER COVER FD |
| Парткод: | 2BM21380 |
| Деталь: | SPRING LEVER FD R |
| Парткод: | 2BM21570 |
| Деталь: | LEVER COVER FD |
| Парткод: | 2BM21500 |
| Деталь: | CASE EXIT FU |
| Парткод: | 2BM21510 |
| Деталь: | SHAFT ROLLER FU |
| Парткод: | 2BM21520 |
| Деталь: | PULLEY EXIT C |
| Парткод: | 2BM21670 |
| Деталь: | COVER EXIT FU |
| Парткод: | 2BM21540 |
| Деталь: | PLATE FDC F |
| Парткод: | 2BM21550 |
| Деталь: | SPRING LEVER FD F |
| Парткод: | 2BM21580 |
| Деталь: | COVER FD |
| Парткод: | 2BM21490 |
| Деталь: | WIRE EARTH FD |
| Парткод: | 2BM42590 |
| Деталь: | Tray FU Assy |
| Парткод: | 2BM68190 |
| Деталь: | TRAY FU A |
| Парткод: | 2BM04190 |
| Деталь: | TRAY FU B |
| Парткод: | 2BM04200 |
| Деталь: | BAND TRAY |
| Парткод: | 2BM04210 |
| Деталь: | SPONG REAR |
| Парткод: | 2BM02960 |
| Деталь: | LK-800 SCANNER UNIT |
| Парткод: | 5PLPXBEAPKX |
| Деталь: | COVER OZONE |
| Парткод: | 2BM02470 |
| Деталь: | LATCH |
| Парткод: | 2BM02460 |
| Деталь: | HOLDER OF |
| Парткод: | 2BM02450 |
| Деталь: | FAN FUSER 12V |
| Парткод: | 2CK27560 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 2BM27890 |
| Деталь: | DUCT FAN |
| Парткод: | 2BM23010 |
| Деталь: | PLATE EARTH MAIN B |
| Парткод: | 2BM42530 |
| Деталь: | PLATE EARTH MAIN |
| Парткод: | 2BM02390 |
| Деталь: | PWB HV MAIN |
| Парткод: | 2CK28170 |
| Деталь: | SPRING SW DU |
| Парткод: | 2BM02900 |
| Деталь: | SWITCH DU |
| Парткод: | 2BM02910 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | PLATE EARTH L |
| Парткод: | 2BM42560 |
| Деталь: | HOLDER HARNESS |
| Парткод: | 2BM02480 |
| Деталь: | PWB HV TC |
| Парткод: | 2CK28180 |
| Деталь: | OPR KP-995 ASSY |
| Парткод: | 2CK01170 |
| Деталь: | PLATE EARTH TC |
| Парткод: | 2BM02410 |
| Деталь: | PLATE EARTH OP |
| Парткод: | 2BM02420 |
| Деталь: | PLATE EARTH DRV FUS |
| Парткод: | 2BM42520 |
| Деталь: | PLATE EARTH DRV TK A |
| Парткод: | 2BM42540 |
| Деталь: | STAY MIDDLE ASSY |
| Парткод: | 2BM00150 |
| Деталь: | LOCK SHUTTER D1234 |
| Парткод: | 2BM14120 |
| Деталь: | SEAL FEED TONER |
| Парткод: | 2BM42600 |
| Деталь: | FEED TONER D4 ASSY |
| Парткод: | 2CK00370 |
| Деталь: | SHUTTER D1234 |
| Парткод: | 2BM14240 |
| Деталь: | SPRING SHUTTER D1234 |
| Парткод: | 2BM14230 |
| Деталь: | SEAL SHUTTER D1234 |
| Парткод: | 2BM14250 |
| Деталь: | GUIDE SHUTTER D1234 |
| Парткод: | 2BM14200 |
| Деталь: | SEAL GUIDE T D1234 |
| Парткод: | 2BM14260 |
| Деталь: | PLATE FEED TK |
| Парткод: | 2BM15940 |
| Деталь: | SEAL FEED TK D |
| Парткод: | 2BM42310 |
| Деталь: | SEAL FEED TK A |
| Парткод: | 2BM15950 |
| Деталь: | SCREW FEED TK |
| Парткод: | 2BM15930 |
| Деталь: | GEAR FEED TK Z23 |
| Парткод: | 2BM42250 |
| Деталь: | BUSH SCREW TK F |
| Парткод: | 2BM42220 |
| Деталь: | BKT SEAL OIL |
| Парткод: | 2BM42240 |
| Деталь: | SEAL TONER A |
| Парткод: | 4AK73480 |
| Деталь: | GUIDE SCREW D14 |
| Парткод: | 2BM14640 |
| Деталь: | SEAL FEED TK B |
| Парткод: | 2BM15960 |
| Деталь: | SEAL FEED TK C |
| Парткод: | 2BM15970 |
| Деталь: | BUSH FEED TK |
| Парткод: | 2BM15920 |
| Деталь: | CASE FEED TK |
| Парткод: | 2BM15910 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM42280 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | FRAME REAR |
| Парткод: | 2BM02070 |
| Деталь: | BUSH PIN OVAL |
| Парткод: | 2BM02440 |
| Деталь: | BUSH PIN |
| Парткод: | 2BM02430 |
| Деталь: | PLATE HV IM |
| Парткод: | 2BM02150 |
| Деталь: | COVER HVIMAGE |
| Парткод: | 2BM02140 |
| Деталь: | SPRING HV S |
| Парткод: | 2BM02160 |
| Деталь: | PIN CONTACT HV |
| Парткод: | 2BM02110 |
| Деталь: | COVER HV FEED |
| Парткод: | 2BM02170 |
| Деталь: | PLATE HV TC |
| Парткод: | 2BM02180 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 2CK68050 |
| Деталь: | BKT SENSOR WASTE A |
| Парткод: | 2CK02220 |
| Деталь: | P.W.BOARD KP-849 ASSY |
| Парткод: | 2BM01230 |
| Деталь: | CONN.CORD T.SENSOR ASSY |
| Парткод: | 2BM28780 |
| Деталь: | COVER HV DRUM |
| Парткод: | 2BM02080 |
| Деталь: | SPRING HV L |
| Парткод: | 2BM02120 |
| Деталь: | PLATE HV D1 |
| Парткод: | 2BM02090 |
| Деталь: | PLATE HV D2 |
| Парткод: | 2BM02100 |
| Деталь: | BRACKET CONN DRUM |
| Парткод: | 2BM42030 |
| Деталь: | SPRING CONN DRUM |
| Парткод: | 2BM42440 |
| Деталь: | SCREW CONNECTOR |
| Парткод: | 2BM02210 |
| Деталь: | BKT CONN D12 A |
| Парткод: | 2CK02250 |
| Деталь: | SPRING CONN DLP |
| Парткод: | 2CK02240 |
| Деталь: | BKT CONN D34 A |
| Парткод: | 2CK02260 |
| Деталь: | STUD SCREW 485 |
| Парткод: | 2BM42450 |
| Деталь: | SPRING CONN FEED |
| Парткод: | 2BM42010 |
| Деталь: | PLATE ANCHOR A |
| Парткод: | 2BM02490 |
| Деталь: | TUBE TONER D4 ASSY |
| Парткод: | 2CK00380 |
| Деталь: | DUCT WASTE TONER UNIT A |
| Парткод: | 2CK00540 |
| Деталь: | P.W.BOARD KP-896 ASSY |
| Парткод: | 2BM01270 |
| Деталь: | BKT SENSOR LOW D4 |
| Парткод: | 2BM42260 |
| Деталь: | COVER HV DLP |
| Парткод: | 2BM02890 |
| Деталь: | PWB HV DLP |
| Парткод: | 2CK28190 |
| Деталь: | RAIL IMAGE R |
| Парткод: | 2BM02780 |
| Деталь: | STOPPER IMAGE |
| Парткод: | 2BM42040 |
| Деталь: | BRACKET LOCK IMAGE |
| Парткод: | 2BM02790 |
| Деталь: | PULLEY IMAGE |
| Парткод: | 2BM02810 |
| Деталь: | LEVER LOCK IMAGE |
| Парткод: | 2BM02800 |
| Деталь: | SPRING LOCK IMAGE |
| Парткод: | 2BM02820 |
| Деталь: | STAY RAIL LOW R A |
| Парткод: | 2BM02630 |
| Деталь: | SLIDE RAIL LOW |
| Парткод: | 2CK02130 |
| Деталь: | STAY RAIL LOW R B |
| Парткод: | 2BM02640 |
| Деталь: | SHIELD REG SENSOR A |
| Парткод: | 2CK02190 |
| Деталь: | STAY RAIL LOW L A |
| Парткод: | 2BM02650 |
| Деталь: | STAY RAIL LOW L B |
| Парткод: | 2BM02660 |
| Деталь: | GUIDE PAPER OUT |
| Парткод: | 2BM02570 |
| Деталь: | GUIDE PAPER IN |
| Парткод: | 2BM02560 |
| Деталь: | FRAME BASE |
| Парткод: | 2CK02040 |
| Деталь: | LOCK PIN |
| Парткод: | 2BM02520 |
| Деталь: | HOLDER FRONT |
| Парткод: | 2BM02930 |
| Деталь: | STAY BASE R |
| Парткод: | 2BM02860 |
| Деталь: | STAY BASE L |
| Парткод: | 2BM02870 |
| Деталь: | FOOT R |
| Парткод: | 2BM42290 |
| Деталь: | PLATE EARTH LOWER |
| Парткод: | 2BM02550 |
| Деталь: | SHIELD REG SENSOR B |
| Парткод: | 2BM42740 |
| Деталь: | Frame Front |
| Парткод: | 2CK02120 |
| Деталь: | STAY RAIL FRONT |
| Парткод: | 2BM02030 |
| Деталь: | CHANNEL BOTTOM |
| Парткод: | 2BM02020 |
| Деталь: | FOOT F |
| Парткод: | 2BM42300 |
| Деталь: | SHEET INNER FRONT |
| Парткод: | 2CK02010 |
| Деталь: | INNER FRONT COVER |
| Парткод: | 2BM04310 |
| Деталь: | MAGNET CATCH |
| Парткод: | 60804120 |
| Деталь: | LEVER INTER LOCK |
| Парткод: | 2BM02060 |
| Деталь: | INTERLOCK SWITCH |
| Парткод: | 2CK27590 |
| Деталь: | SLIDE RAIL PRO |
| Парткод: | 2CK02140 |
| Деталь: | GUIDE CONTAINER D4 |
| Парткод: | 2BM02710 |
| Деталь: | STAY PRO R ASSY |
| Парткод: | 2BM02680 |
| Деталь: | STAY RAIL PRO R B |
| Парткод: | 2BM02690 |
| Деталь: | SUPPORT PULLEY TRANS |
| Парткод: | 2BM02730 |
| Деталь: | PULLEY IMAGE L |
| Парткод: | 2BM02740 |
| Деталь: | BKT PULLEY IMAGE |
| Парткод: | 2BM02720 |
| Деталь: | STAY RAIL PRO L A |
| Парткод: | 2BM02750 |
| Деталь: | STAY RAIL PRO L B |
| Парткод: | 2BM02760 |
| Деталь: | SEAL RAIL PRO B |
| Парткод: | 2CK02170 |
| Деталь: | SEAL STAY PRO A |
| Парткод: | 2BM42620 |
| Деталь: | PLATE SCANNER BASE |
| Парткод: | 2BM02850 |
| Деталь: | BKT SENSOR UP D4 |
| Парткод: | 2BM42270 |
| Деталь: | P.W.BOARD KP-895 ASSY |
| Парткод: | 2BM01260 |
| Деталь: | PLATE EARTH DRV TK B |
| Парткод: | 2BM42550 |
| Деталь: | FRAME REAR PROCESS |
| Парткод: | 2CK02060 |
| Деталь: | PIN REAR PROCESS |
| Парткод: | 2CK02160 |
| Деталь: | STAY ACCURIDE PRO R |
| Парткод: | 2BM08540 |
| Деталь: | COVER BOTTOM PROCESS |
| Парткод: | 2BM08550 |
| Деталь: | PRESS ARM D4 |
| Парткод: | 2BM08610 |
| Деталь: | SPRING D4 PROCESS |
| Парткод: | 2BM08620 |
| Деталь: | STAY PROCESS BASE |
| Парткод: | 2BM08530 |
| Деталь: | COVER LEFT PROCESS |
| Парткод: | 2BM02830 |
| Деталь: | FRAME FRONT PROCESS |
| Парткод: | 2BM08510 |
| Деталь: | LOCK PROCESS R |
| Парткод: | 2BM42430 |
| Деталь: | TP SCREW |
| Парткод: | 5MMT273SZ004 |
| Деталь: | PLATE LOCK R |
| Парткод: | 2BM02990 |
| Деталь: | PLATE LOCK L |
| Парткод: | 2BM02980 |
| Деталь: | LOCK PROCESS |
| Парткод: | 2BM08590 |
| Деталь: | LOCK MCH |
| Парткод: | 2BM08570 |
| Деталь: | SPRING LOCK MCH |
| Парткод: | 2BM08580 |
| Деталь: | LABEL CLEANER |
| Парткод: | 2BM05220 |
| Деталь: | SCREW PROCESS |
| Парткод: | 2BM02840 |
| Деталь: | SPRING FRAME PRO |
| Парткод: | 2BM42660 |
| Деталь: | SPONG REAR |
| Парткод: | 2BM02960 |
| Деталь: | LK-800 SCANNER UNIT |
| Парткод: | 5PLPXBEAPKX |
| Деталь: | COVER OZONE |
| Парткод: | 2BM02470 |
| Деталь: | LATCH |
| Парткод: | 2BM02460 |
| Деталь: | HOLDER OF |
| Парткод: | 2BM02450 |
| Деталь: | FAN FUSER 12V |
| Парткод: | 2CK27560 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 2BM27890 |
| Деталь: | DUCT FAN |
| Парткод: | 2BM23010 |
| Деталь: | PLATE EARTH MAIN B |
| Парткод: | 2BM42530 |
| Деталь: | PLATE EARTH MAIN |
| Парткод: | 2BM02390 |
| Деталь: | PWB HV MAIN |
| Парткод: | 2CK28170 |
| Деталь: | SPRING SW DU |
| Парткод: | 2BM02900 |
| Деталь: | SWITCH DU |
| Парткод: | 2BM02910 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | PLATE EARTH L |
| Парткод: | 2BM42560 |
| Деталь: | HOLDER HARNESS |
| Парткод: | 2BM02480 |
| Деталь: | PWB HV TC |
| Парткод: | 2CK28180 |
| Деталь: | OPR KP-995 ASSY |
| Парткод: | 2CK01170 |
| Деталь: | PLATE EARTH TC |
| Парткод: | 2BM02410 |
| Деталь: | PLATE EARTH OP |
| Парткод: | 2BM02420 |
| Деталь: | PLATE EARTH DRV FUS |
| Парткод: | 2BM42520 |
| Деталь: | PLATE EARTH DRV TK A |
| Парткод: | 2BM42540 |
| Деталь: | STAY MIDDLE ASSY |
| Парткод: | 2BM00150 |
| Деталь: | LOCK SHUTTER D1234 |
| Парткод: | 2BM14120 |
| Деталь: | SEAL FEED TONER |
| Парткод: | 2BM42600 |
| Деталь: | FEED TONER D4 ASSY |
| Парткод: | 2CK00370 |
| Деталь: | SHUTTER D1234 |
| Парткод: | 2BM14240 |
| Деталь: | SPRING SHUTTER D1234 |
| Парткод: | 2BM14230 |
| Деталь: | SEAL SHUTTER D1234 |
| Парткод: | 2BM14250 |
| Деталь: | GUIDE SHUTTER D1234 |
| Парткод: | 2BM14200 |
| Деталь: | SEAL GUIDE T D1234 |
| Парткод: | 2BM14260 |
| Деталь: | PLATE FEED TK |
| Парткод: | 2BM15940 |
| Деталь: | SEAL FEED TK D |
| Парткод: | 2BM42310 |
| Деталь: | SEAL FEED TK A |
| Парткод: | 2BM15950 |
| Деталь: | SCREW FEED TK |
| Парткод: | 2BM15930 |
| Деталь: | GEAR FEED TK Z23 |
| Парткод: | 2BM42250 |
| Деталь: | BUSH SCREW TK F |
| Парткод: | 2BM42220 |
| Деталь: | BKT SEAL OIL |
| Парткод: | 2BM42240 |
| Деталь: | SEAL TONER A |
| Парткод: | 4AK73480 |
| Деталь: | GUIDE SCREW D14 |
| Парткод: | 2BM14640 |
| Деталь: | SEAL FEED TK B |
| Парткод: | 2BM15960 |
| Деталь: | SEAL FEED TK C |
| Парткод: | 2BM15970 |
| Деталь: | BUSH FEED TK |
| Парткод: | 2BM15920 |
| Деталь: | CASE FEED TK |
| Парткод: | 2BM15910 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM42280 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | FRAME REAR |
| Парткод: | 2BM02070 |
| Деталь: | BUSH PIN OVAL |
| Парткод: | 2BM02440 |
| Деталь: | BUSH PIN |
| Парткод: | 2BM02430 |
| Деталь: | PLATE HV IM |
| Парткод: | 2BM02150 |
| Деталь: | COVER HVIMAGE |
| Парткод: | 2BM02140 |
| Деталь: | SPRING HV S |
| Парткод: | 2BM02160 |
| Деталь: | PIN CONTACT HV |
| Парткод: | 2BM02110 |
| Деталь: | COVER HV FEED |
| Парткод: | 2BM02170 |
| Деталь: | PLATE HV TC |
| Парткод: | 2BM02180 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 2CK68050 |
| Деталь: | BKT SENSOR WASTE A |
| Парткод: | 2CK02220 |
| Деталь: | P.W.BOARD KP-849 ASSY |
| Парткод: | 2BM01230 |
| Деталь: | CONN.CORD T.SENSOR ASSY |
| Парткод: | 2BM28780 |
| Деталь: | COVER HV DRUM |
| Парткод: | 2BM02080 |
| Деталь: | SPRING HV L |
| Парткод: | 2BM02120 |
| Деталь: | PLATE HV D1 |
| Парткод: | 2BM02090 |
| Деталь: | PLATE HV D2 |
| Парткод: | 2BM02100 |
| Деталь: | BRACKET CONN DRUM |
| Парткод: | 2BM42030 |
| Деталь: | SPRING CONN DRUM |
| Парткод: | 2BM42440 |
| Деталь: | SCREW CONNECTOR |
| Парткод: | 2BM02210 |
| Деталь: | BKT CONN D12 A |
| Парткод: | 2CK02250 |
| Деталь: | SPRING CONN DLP |
| Парткод: | 2CK02240 |
| Деталь: | BKT CONN D34 A |
| Парткод: | 2CK02260 |
| Деталь: | STUD SCREW 485 |
| Парткод: | 2BM42450 |
| Деталь: | SPRING CONN FEED |
| Парткод: | 2BM42010 |
| Деталь: | PLATE ANCHOR A |
| Парткод: | 2BM02490 |
| Деталь: | TUBE TONER D4 ASSY |
| Парткод: | 2CK00380 |
| Деталь: | DUCT WASTE TONER UNIT A |
| Парткод: | 2CK00540 |
| Деталь: | P.W.BOARD KP-896 ASSY |
| Парткод: | 2BM01270 |
| Деталь: | BKT SENSOR LOW D4 |
| Парткод: | 2BM42260 |
| Деталь: | COVER HV DLP |
| Парткод: | 2BM02890 |
| Деталь: | PWB HV DLP |
| Парткод: | 2CK28190 |
| Деталь: | RAIL IMAGE R |
| Парткод: | 2BM02780 |
| Деталь: | STOPPER IMAGE |
| Парткод: | 2BM42040 |
| Деталь: | BRACKET LOCK IMAGE |
| Парткод: | 2BM02790 |
| Деталь: | PULLEY IMAGE |
| Парткод: | 2BM02810 |
| Деталь: | LEVER LOCK IMAGE |
| Парткод: | 2BM02800 |
| Деталь: | SPRING LOCK IMAGE |
| Парткод: | 2BM02820 |
| Деталь: | STAY RAIL LOW R A |
| Парткод: | 2BM02630 |
| Деталь: | SLIDE RAIL LOW |
| Парткод: | 2CK02130 |
| Деталь: | STAY RAIL LOW R B |
| Парткод: | 2BM02640 |
| Деталь: | SHIELD REG SENSOR A |
| Парткод: | 2CK02190 |
| Деталь: | STAY RAIL LOW L A |
| Парткод: | 2BM02650 |
| Деталь: | STAY RAIL LOW L B |
| Парткод: | 2BM02660 |
| Деталь: | GUIDE PAPER OUT |
| Парткод: | 2BM02570 |
| Деталь: | GUIDE PAPER IN |
| Парткод: | 2BM02560 |
| Деталь: | FRAME BASE |
| Парткод: | 2CK02040 |
| Деталь: | LOCK PIN |
| Парткод: | 2BM02520 |
| Деталь: | HOLDER FRONT |
| Парткод: | 2BM02930 |
| Деталь: | STAY BASE R |
| Парткод: | 2BM02860 |
| Деталь: | STAY BASE L |
| Парткод: | 2BM02870 |
| Деталь: | FOOT R |
| Парткод: | 2BM42290 |
| Деталь: | PLATE EARTH LOWER |
| Парткод: | 2BM02550 |
| Деталь: | SHIELD REG SENSOR B |
| Парткод: | 2BM42740 |
| Деталь: | Frame Front |
| Парткод: | 2CK02120 |
| Деталь: | STAY RAIL FRONT |
| Парткод: | 2BM02030 |
| Деталь: | CHANNEL BOTTOM |
| Парткод: | 2BM02020 |
| Деталь: | FOOT F |
| Парткод: | 2BM42300 |
| Деталь: | SHEET INNER FRONT |
| Парткод: | 2CK02010 |
| Деталь: | INNER FRONT COVER |
| Парткод: | 2BM04310 |
| Деталь: | MAGNET CATCH |
| Парткод: | 60804120 |
| Деталь: | LEVER INTER LOCK |
| Парткод: | 2BM02060 |
| Деталь: | INTERLOCK SWITCH |
| Парткод: | 2CK27590 |
| Деталь: | SLIDE RAIL PRO |
| Парткод: | 2CK02140 |
| Деталь: | GUIDE CONTAINER D4 |
| Парткод: | 2BM02710 |
| Деталь: | STAY PRO R ASSY |
| Парткод: | 2BM02680 |
| Деталь: | STAY RAIL PRO R B |
| Парткод: | 2BM02690 |
| Деталь: | SUPPORT PULLEY TRANS |
| Парткод: | 2BM02730 |
| Деталь: | PULLEY IMAGE L |
| Парткод: | 2BM02740 |
| Деталь: | BKT PULLEY IMAGE |
| Парткод: | 2BM02720 |
| Деталь: | STAY RAIL PRO L A |
| Парткод: | 2BM02750 |
| Деталь: | STAY RAIL PRO L B |
| Парткод: | 2BM02760 |
| Деталь: | SEAL RAIL PRO B |
| Парткод: | 2CK02170 |
| Деталь: | SEAL STAY PRO A |
| Парткод: | 2BM42620 |
| Деталь: | PLATE SCANNER BASE |
| Парткод: | 2BM02850 |
| Деталь: | BKT SENSOR UP D4 |
| Парткод: | 2BM42270 |
| Деталь: | P.W.BOARD KP-895 ASSY |
| Парткод: | 2BM01260 |
| Деталь: | PLATE EARTH DRV TK B |
| Парткод: | 2BM42550 |
| Деталь: | FRAME REAR PROCESS |
| Парткод: | 2CK02060 |
| Деталь: | PIN REAR PROCESS |
| Парткод: | 2CK02160 |
| Деталь: | STAY ACCURIDE PRO R |
| Парткод: | 2BM08540 |
| Деталь: | COVER BOTTOM PROCESS |
| Парткод: | 2BM08550 |
| Деталь: | PRESS ARM D4 |
| Парткод: | 2BM08610 |
| Деталь: | SPRING D4 PROCESS |
| Парткод: | 2BM08620 |
| Деталь: | STAY PROCESS BASE |
| Парткод: | 2BM08530 |
| Деталь: | COVER LEFT PROCESS |
| Парткод: | 2BM02830 |
| Деталь: | FRAME FRONT PROCESS |
| Парткод: | 2BM08510 |
| Деталь: | LOCK PROCESS R |
| Парткод: | 2BM42430 |
| Деталь: | TP SCREW |
| Парткод: | 5MMT273SZ004 |
| Деталь: | PLATE LOCK R |
| Парткод: | 2BM02990 |
| Деталь: | PLATE LOCK L |
| Парткод: | 2BM02980 |
| Деталь: | LOCK PROCESS |
| Парткод: | 2BM08590 |
| Деталь: | LOCK MCH |
| Парткод: | 2BM08570 |
| Деталь: | SPRING LOCK MCH |
| Парткод: | 2BM08580 |
| Деталь: | LABEL CLEANER |
| Парткод: | 2BM05220 |
| Деталь: | SCREW PROCESS |
| Парткод: | 2BM02840 |
| Деталь: | SPRING FRAME PRO |
| Парткод: | 2BM42660 |
| Деталь: | DV-803K DEVELOPER BLACK |
| Парткод: | 2CK93090 |
| Деталь: | GEAR Z14-Z12 D4 |
| Парткод: | 2CK1423 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM4006 |
| Деталь: | JOINT D1234 |
| Парткод: | 2CK1430 |
| Деталь: | BUSH CLUTCH D1234 |
| Парткод: | 2BM1406 |
| Деталь: | BKT CLUTCH D4 |
| Парткод: | 2CK1417 |
| Деталь: | CLUTCH 26-H |
| Парткод: | 2BM2796 |
| Деталь: | GEAR Z30H-Z22H D4 |
| Парткод: | 2CK1444 |
| Деталь: | GEAR Z24-Z18-8 D4 |
| Парткод: | 2CK1422 |
| Деталь: | SHAFT CLUTCH D1234 |
| Парткод: | 2CK1431 |
| Деталь: | GEAR Z14D-8 D1234 |
| Парткод: | 2CK1433 |
| Деталь: | DV-803Y DEVELOPER YELLOW |
| Парткод: | 2CK93030 |
| Деталь: | SHAFT GEAR D12 |
| Парткод: | 2CK1424 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM4006 |
| Деталь: | JOINT D1234 |
| Парткод: | 2CK1430 |
| Деталь: | BUSH CLUTCH D1234 |
| Парткод: | 2BM1406 |
| Деталь: | Bush |
| Парткод: | 2BM1453 |
| Деталь: | BKT CLUTCH D1 |
| Парткод: | 2CK1402 |
| Деталь: | CLUTCH 26-D |
| Парткод: | 2BM2735 |
| Деталь: | GEAR Z14-8 JOINT D12 |
| Парткод: | 2CK1443 |
| Деталь: | GEAR Z30H-Z17H D12 |
| Парткод: | 2CK1425 |
| Деталь: | GEAR Z15-Z10 D123 |
| Парткод: | 2CK1429 |
| Деталь: | SHAFT CLUTCH D1234 |
| Парткод: | 2CK1431 |
| Деталь: | GEAR Z14D-8 D1234 |
| Парткод: | 2CK1433 |
| Деталь: | GEAR Z15-8 D123 |
| Парткод: | 2CK1428 |
| Деталь: | BUSH BKT CLUTCH D1 |
| Парткод: | 2CK1406 |
| Деталь: | CONN. CORD HV T2 ASSY |
| Парткод: | 2BM28790 |
| Деталь: | CONN. CORD HV G ASSY |
| Парткод: | 2BM28860 |
| Деталь: | CONN. CORD HV MAIN ASSY |
| Парткод: | 2BM28870 |
| Деталь: | CONN. CORD FEED-HUMIDITY ASSY |
| Парткод: | 2CK27070 |
| Деталь: | CONN. CORD FEED ASSY |
| Парткод: | 2BM28670 |
| Деталь: | CONN. CORD HV CR ASSY |
| Парткод: | 2BM28850 |
| Деталь: | CONN. CORD HV T1 ASSY |
| Парткод: | 2BM28800 |
| Деталь: | CONN. CORD HV BK ASSY |
| Парткод: | 2BM28840 |
| Деталь: | CONN. CORD HV BC ASSY |
| Парткод: | 2BM28830 |
| Деталь: | CONN. CORD HV BM ASSY |
| Парткод: | 2BM28820 |
| Деталь: | CONN. CORD HV BY ASSY |
| Парткод: | 2BM28810 |
| Деталь: | CONN. CORD APC-B ASSY |
| Парткод: | 2CK27000 |
| Деталь: | CONN. CORD PS2-B ASSY |
| Парткод: | 2CK27300 |
| Деталь: | CONN. CORD HEAT CONT-B ASSY |
| Парткод: | 2CK27210 |
| Деталь: | CONN. CORD POWER E.-B ASSY |
| Парткод: | 2CK27200 |
| Деталь: | CONN. CORD SW.RELAY ASSY |
| Парткод: | 2CK27310 |
| Деталь: | CONN. CORD E2P-KTS ASSY |
| Парткод: | 2CK27230 |
| Деталь: | CONN. CORD COVER SW.-B ASSY |
| Парткод: | 2CK27180 |
| Деталь: | CONN. CORD CMT-DRV-HVM ASSY |
| Парткод: | 2CK27100 |
| Деталь: | CONN. CORD DRIVE MAIN ASSY |
| Парткод: | 2BM27610 |
| Деталь: | CONN. CORD KMT-DRMT ASSY |
| Парткод: | 2CK27110 |
| Деталь: | CONN. CORD OP.RERAY-B ASSY |
| Парткод: | 2CK27190 |
| Деталь: | CONN. CORD HV-T2-B ASSY |
| Парткод: | 2CK27160 |
| Деталь: | CONN. CORD PF/DU ASSY |
| Парткод: | 2BM28720 |
| Деталь: | CONN. CORD TRANSFER-B ASSY |
| Парткод: | 2CK27080 |
| Деталь: | CONN. CORD FUSER-B ASSY |
| Парткод: | 2CK27120 |
| Деталь: | CONN. CORD DRUM ASSY |
| Парткод: | 2BM28640 |
| Деталь: | CONN. CORD S02597 ASSY |
| Парткод: | 2BM28760 |
| Деталь: | CONN. CORD DLP YM ASSY |
| Парткод: | 2BM28540 |
| Деталь: | CONN. CORD DLP CK-B ASSY |
| Парткод: | 2CK27020 |
| Деталь: | FE-803 FEED UNIT |
| Парткод: | 2CK93160 |
| Деталь: | ROLLER REGIST UP |
| Парткод: | 2BM17400 |
| Деталь: | BUSH REGIST UP |
| Парткод: | 2BM17330 |
| Деталь: | GEAR REGIST Z24 |
| Парткод: | 2BM17950 |
| Деталь: | SPRING MIDDLE F |
| Парткод: | 2BM17350 |
| Деталь: | SPRING REGIST F |
| Парткод: | 2BM17420 |
| Деталь: | ROLLER REGIST LOW |
| Парткод: | 2BM17370 |
| Деталь: | JOINT ROLL TRANS |
| Парткод: | 2BM17390 |
| Деталь: | GEAR REGIST Z32 |
| Парткод: | 2BM17380 |
| Деталь: | SLOPE IMAGE UNIT |
| Парткод: | 2BM43010 |
| Деталь: | PAD REG SENSOR |
| Парткод: | 2BM17440 |
| Деталь: | Latch Joint |
| Парткод: | 5MVM286DB002 |
| Деталь: | METAL BUSH KD |
| Парткод: | 5MMM176CJ003 |
| Деталь: | SHAFT PULLEY MIDDLE |
| Парткод: | 2BM17300 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 2BM17310 |
| Деталь: | SPRING MIDDLE R |
| Парткод: | 2BM17360 |
| Деталь: | SPRING GUIDE MIDDLE |
| Парткод: | 2BM17340 |
| Деталь: | GUIDE MIDDLE |
| Парткод: | 2BM17290 |
| Деталь: | LEVER GUIDE MIDDLE |
| Парткод: | 2BM17320 |
| Деталь: | SHEET REGIST B |
| Парткод: | 2BM17500 |
| Деталь: | PLATE EARTH REG A |
| Парткод: | 2BM17460 |
| Деталь: | HIGH-MEG R ASSY |
| Парткод: | 2BM17480 |
| Деталь: | Plate Release |
| Парткод: | 2BM17120 |
| Деталь: | SPRING RELEASE |
| Парткод: | 2BM17130 |
| Деталь: | Case Low |
| Парткод: | 2BM17013 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 2BM17970 |
| Деталь: | GEAR JOINT Z22S |
| Парткод: | 2BM17260 |
| Деталь: | PLATE CONTACT TRANS |
| Парткод: | 2BM17090 |
| Деталь: | CONN CORD FEED2 ASSY |
| Парткод: | 2BM27260 |
| Деталь: | GEAR Z23S |
| Парткод: | 2CK17420 |
| Деталь: | FAN BELT |
| Парткод: | 2BM27230 |
| Деталь: | DUCT FEED WIDE |
| Парткод: | 2CK17750 |
| Деталь: | SCREW FAN BELT |
| Парткод: | 2BM17960 |
| Деталь: | GUIDE LEFT ASSY |
| Парткод: | 2BM68160 |
| Деталь: | GUIDE CHANGE DU |
| Парткод: | 2BM17151 |
| Деталь: | PLATE LEVER SOL |
| Парткод: | 2BM17180 |
| Деталь: | HOOK LOCK FUSER |
| Парткод: | 2BM17170 |
| Деталь: | SOLENOID FEED |
| Парткод: | 2BM27160 |
| Деталь: | ANGLE SOLENOID |
| Парткод: | 2BM17190 |
| Деталь: | PLATE DU SENSOR |
| Парткод: | 2BM43100 |
| Деталь: | GUIDE CASE LOW LEFT |
| Парткод: | 2BM17140 |
| Деталь: | PT.SENSOR GP2S30 |
| Парткод: | 2BM27170 |
| Деталь: | LEVER LOCK CASE LOW |
| Парткод: | 2BM17160 |
| Деталь: | COVER GUIDE DU |
| Парткод: | 2BM17200 |
| Деталь: | REFLECTOR DU SENSOR |
| Парткод: | 2BM43120 |
| Деталь: | CONN.CORD EXIT JAM DU |
| Парткод: | 2BM27940 |
| Деталь: | CONN.CORD FEED EARTH ASSY |
| Парткод: | 2BM44030 |
| Деталь: | SPRING LOCK FUSER |
| Парткод: | 2BM17210 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | PLATE SUPPORT FEED |
| Парткод: | 2BM43060 |
| Деталь: | PLATE BOTTOM FEED |
| Парткод: | 2BM17020 |
| Деталь: | PLATE FRONT LEVER |
| Парткод: | 2BM17030 |
| Деталь: | HOOK LEVER FRONT |
| Парткод: | 2BM17060 |
| Деталь: | PLATE EARTH BOTTOM |
| Парткод: | 2BM43070 |
| Деталь: | SPRING FRONT LEVER |
| Парткод: | 2BM17070 |
| Деталь: | BUSH POM |
| Парткод: | 5MVM122DB003 |
| Деталь: | LEVER FEED FRONT |
| Парткод: | 2BM17050 |
| Деталь: | SHAFT FRONT LEVER |
| Парткод: | 2BM17040 |
| Деталь: | BELT ASSY |
| Парткод: | 2CK68040 |
| Деталь: | GEAR Z42S |
| Парткод: | 2BM17620 |
| Деталь: | PULLEY TENSION BELT |
| Парткод: | 2BM17630 |
| Деталь: | SHAFT TENSION WIDE |
| Парткод: | 2CK17790 |
| Деталь: | METAL BUSH TRANS |
| Парткод: | 2BM43080 |
| Деталь: | SHAFT BELT L-WIDE |
| Парткод: | 2CK17780 |
| Деталь: | BELT TRANS |
| Парткод: | 2CK17480 |
| Деталь: | PULLEY BELT L-WIDE |
| Парткод: | 2CK17760 |
| Деталь: | SCREW FEED UNIT |
| Парткод: | 2BM02920 |
| Деталь: | CONN.CORD REG ASSY |
| Парткод: | 2BM27200 |
| Деталь: | CONN CORD FEED1 ASSY |
| Парткод: | 2BM27250 |
| Деталь: | SEAL SIDE SENS WASTE |
| Парткод: | 2BM42760 |
| Деталь: | PAD BOTTOM FEED |
| Парткод: | 2BM43040 |
| Деталь: | SPRING EARTH FEED |
| Парткод: | 2BM43050 |
| Деталь: | CONN. CORD FEED CL ASSY |
| Парткод: | 2BM44060 |
| Деталь: | MINIATURE CLAMP, UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | FED KP-1013 ASSY |
| Парткод: | 2CK01160 |
| Деталь: | STOPPER PI |
| Парткод: | 2CK02030 |
| Деталь: | BUSH CONDUCTIVE |
| Парткод: | 2CK16010 |
| Деталь: | ROLLER MIDDLE |
| Парткод: | 2CK17010 |
| Деталь: | GEAR Z22S-Z14S |
| Парткод: | 2CK17020 |
| Деталь: | GEAR IDLEZ22S |
| Парткод: | 2CK17040 |
| Деталь: | GEAR IDLEZ26S |
| Парткод: | 2CK17060 |
| Деталь: | GEAR IDLEZ14S |
| Парткод: | 2CK17050 |
| Деталь: | BUSH TRANS UNIT |
| Парткод: | 2CK17070 |
| Деталь: | CAM TRANS R |
| Парткод: | 2CK17080 |
| Деталь: | GUIDE PAPER REGIST |
| Парткод: | 2CK17110 |
| Деталь: | PLATE REG SENSOR |
| Парткод: | 2CK17120 |
| Деталь: | PLATE TC GEAR |
| Парткод: | 2CK17140 |
| Деталь: | PLATE GEAR IDLE |
| Парткод: | 2CK17150 |
| Деталь: | PLATE EARTH CASE |
| Парткод: | 2CK17160 |
| Деталь: | SHAFT TC GEAR |
| Парткод: | 2CK17170 |
| Деталь: | SHAFT GEAR IDLE |
| Парткод: | 2CK17180 |
| Деталь: | SHAFT BELT R |
| Парткод: | 2CK17191 |
| Деталь: | SHEET REGIST |
| Парткод: | 2CK17200 |
| Деталь: | SEAL BELT LOW |
| Парткод: | 2CK17241 |
| Деталь: | SEAL PLATE BELT |
| Парткод: | 2CK17271 |
| Деталь: | SEAL BELT UP |
| Парткод: | 2CK17281 |
| Деталь: | LABEL CAUTION TC |
| Парткод: | 2CK17310 |
| Деталь: | BUSH TC |
| Парткод: | 2CK17320 |
| Деталь: | SEAL COVER FG |
| Парткод: | 2CK17440 |
| Деталь: | CAM TRANS F |
| Парткод: | 2CK17330 |
| Деталь: | RIB BELT |
| Парткод: | 2CK17340 |
| Деталь: | SHEET MIDDLE |
| Парткод: | 2CK17370 |
| Деталь: | PULLEY BELT R-WIDE |
| Парткод: | 2CK17770 |
| Деталь: | SEAL FEED FRONT |
| Парткод: | 2CK17390 |
| Деталь: | SEAL FEED BOTTOM |
| Парткод: | 2CK17400 |
| Деталь: | TAPE EARTH BELT |
| Парткод: | 2CK17410 |
| Деталь: | GEAR Z22S |
| Парткод: | 2CK17030 |
| Деталь: | PLATE GEAR FUSER A |
| Парткод: | 2CK17430 |
| Деталь: | PLATE BELT WIDE |
| Парткод: | 2CK17490 |
| Деталь: | SHEET GUIDE DU |
| Парткод: | 2CK17460 |
| Деталь: | CONN.CORD EARTH CASE ASSY |
| Парткод: | 2CK27280 |
| Деталь: | CONN.CORD REGIST EARTH AS |
| Парткод: | 2CK27330 |
| Деталь: | CLUTCH SP CAM |
| Парткод: | 2CK27520 |
| Деталь: | PT.SENSOR KR1207-KM2 |
| Парткод: | 2CK27650 |
| Деталь: | RIB BELT SIDE |
| Парткод: | 2CK17800 |
| Деталь: | TR-803S SEC TRANSFER UNIT |
| Парткод: | 2CK93170 |
| Деталь: | BELT SEPARATOR |
| Парткод: | 2CK17530 |
| Деталь: | Guide Chute Low |
| Парткод: | 2BM17710 |
| Деталь: | PLATE SPACER TC |
| Парткод: | 2CK17670 |
| Деталь: | GEAR TC Z18S |
| Парткод: | 2CK17580 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GEAR TC Z14S |
| Парткод: | 2CK17570 |
| Деталь: | PLATE TC JOINT |
| Парткод: | 2CK17590 |
| Деталь: | PLATE CONTACT TC |
| Парткод: | 2CK17610 |
| Деталь: | HOUSING TRANS |
| Парткод: | 2CK17540 |
| Деталь: | ERASER TC |
| Парткод: | 2CK17650 |
| Деталь: | PLATE EARTH TC |
| Парткод: | 2CK17600 |
| Деталь: | ROLLER TRANSFER D |
| Парткод: | 2CK17510 |
| Деталь: | ROLLER TRANSFER U |
| Парткод: | 2CK17520 |
| Деталь: | PLATE CONTACT ERASER |
| Парткод: | 2CK17660 |
| Деталь: | LEVER TRANS B |
| Парткод: | 2BM17740 |
| Деталь: | LEVER TRANS R |
| Парткод: | 2CK17560 |
| Деталь: | SPRING TC R |
| Парткод: | 2CK17630 |
| Деталь: | BEARING SEPARATOR |
| Парткод: | 2CK17640 |
| Деталь: | SPRING TC L |
| Парткод: | 2CK17620 |
| Деталь: | LEVER TRANS F |
| Парткод: | 2CK17550 |
| Деталь: | DR-803A DRIVE UNIT A |
| Парткод: | 2CK93180 |
| Деталь: | DR-803B DRIVE UNIT B |
| Парткод: | 2CK93190 |
| Деталь: | DR-803C DRIVE UNIT C |
| Парткод: | 2CK68030 |
| Деталь: | DR-803D DRIVE UNIT D |
| Парткод: | 2CK93200 |
| Деталь: | MOTOR MAIN |
| Парткод: | 2BM27690 |
| Деталь: | HOLDER ASSY B |
| Парткод: | 2BM22200 |
| Деталь: | PLATE DRIVE MAIN B |
| Парткод: | 2BM22020 |
| Деталь: | GEAR Z144H BT |
| Парткод: | 2BM23870 |
| Деталь: | MOTOR DLP |
| Парткод: | 2BM27700 |
| Деталь: | GEAR Z36H Z117H |
| Парткод: | 2BM22060 |
| Деталь: | BUSH 6-9-4 |
| Парткод: | 2BM22360 |
| Деталь: | EDGING EDS-0607U |
| Парткод: | M2104260 |
| Деталь: | GEAR Z30 Z58H |
| Парткод: | 2CK22060 |
| Деталь: | GEAR Z25 Z29 |
| Парткод: | 2BM22090 |
| Деталь: | GEAR Z23 IDLE |
| Парткод: | 2BM22170 |
| Деталь: | GEAR Z29 IDLE |
| Парткод: | 2BM22100 |
| Деталь: | GEAR Z14 Z29 |
| Парткод: | 2BM22160 |
| Деталь: | GEAR Z43H |
| Парткод: | 2BM22140 |
| Деталь: | GEAR Z30 Z57H |
| Парткод: | 2CK22070 |
| Деталь: | GEAR Z53 |
| Парткод: | 2BM23760 |
| Деталь: | PLATE DRIVE MAIN C |
| Парткод: | 2CK22050 |
| Деталь: | GEAR Z26 IDLE |
| Парткод: | 2BM22110 |
| Деталь: | GEAR Z34 |
| Парткод: | 2BM23750 |
| Деталь: | GEAR Z30 JOINT MIX |
| Парткод: | 2CK22020 |
| Деталь: | BUSH MAIN C |
| Парткод: | 2BM23800 |
| Деталь: | GEAR Z21H Z26 |
| Парткод: | 2BM22150 |
| Деталь: | GEAR Z28 |
| Парткод: | 2BM22180 |
| Деталь: | CLUTCH ASSY 2 |
| Парткод: | 2CK22130 |
| Деталь: | HOLDER ASSY CHY |
| Парткод: | 2CK22150 |
| Деталь: | HOLDER ASSY CHM |
| Парткод: | 2CK22160 |
| Деталь: | HOLDER ASSY CHC |
| Парткод: | 2CK22170 |
| Деталь: | HOLDER ASSY CHK |
| Парткод: | 2CK22140 |
| Деталь: | PLATE DRIVE MAIN A |
| Парткод: | 2CK22030 |
| Деталь: | BUSH CL CAM |
| Парткод: | 2BM22270 |
| Деталь: | SHAFT JOINT CAM |
| Парткод: | 2BM22420 |
| Деталь: | CLUTCH ASSY CAM |
| Парткод: | 2BM22280 |
| Деталь: | SHAFT JOINT SCREW |
| Парткод: | 2BM22430 |
| Деталь: | CLUTCH 26-C |
| Парткод: | 2BM27630 |
| Деталь: | HOUSING CL CAM |
| Парткод: | 2BM22260 |
| Деталь: | SPRING JOINT CAM |
| Парткод: | 2BM22460 |
| Деталь: | JOINT CAM |
| Парткод: | 2BM22330 |
| Деталь: | JOINT ROLL SCREW |
| Парткод: | 2BM22320 |
| Деталь: | ACTUATOR CAM |
| Парткод: | 2BM22350 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 2BM22470 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | SOLENOID CAM |
| Парткод: | 2BM27640 |
| Деталь: | PLATE SENSOR |
| Парткод: | 2BM22380 |
| Деталь: | SHAFT JOINT DRUM A |
| Парткод: | 2CK22430 |
| Деталь: | HOLDER ASSY A |
| Парткод: | 2CK22180 |
| Деталь: | SPRING JOINT DRUM BT |
| Парткод: | 2BM23910 |
| Деталь: | JOINT DRUM BT |
| Парткод: | 2BM23900 |
| Деталь: | PW.BOARD KP-824 ASSY |
| Парткод: | 2BM01170 |
| Деталь: | LID HV UNIT |
| Парткод: | 2BM22500 |
| Деталь: | EARTH DLP |
| Парткод: | 2BM22510 |
| Деталь: | PLATE HV JOINT |
| Парткод: | 2BM22530 |
| Деталь: | EARTH DRUM |
| Парткод: | 2BM22520 |
| Деталь: | PLATE HV DRUM |
| Парткод: | 2BM22540 |
| Деталь: | EARTH DRUM T1 |
| Парткод: | 2BM23810 |
| Деталь: | METAL BUSH KD |
| Парткод: | 5MMM176CJ003 |
| Деталь: | CASE HV JOINT DLP |
| Парткод: | 2BM22490 |
| Деталь: | HOLDER HARNESS D |
| Парткод: | 2BM23730 |
| Деталь: | SOLENOID Y |
| Парткод: | 2BM27650 |
| Деталь: | PLATE SOLENOID |
| Парткод: | 2BM22370 |
| Деталь: | LEVER SOLENOID |
| Парткод: | 2BM22340 |
| Деталь: | SPRING LEVER |
| Парткод: | 2BM22440 |
| Деталь: | SEAL SOLENOID |
| Парткод: | 2BM22480 |
| Деталь: | SOLENOID M |
| Парткод: | 2BM27660 |
| Деталь: | SOLENOID C |
| Парткод: | 2BM27670 |
| Деталь: | SOLENOID K |
| Парткод: | 2BM27680 |
| Деталь: | PLATE DRIVE MAIN D |
| Парткод: | 2BM22040 |
| Деталь: | SPRING HV |
| Парткод: | 2BM23780 |
| Деталь: | PLATE GEAR Z144H BT |
| Парткод: | 2BM23860 |
| Деталь: | JOINT GEAR BT |
| Парткод: | 2BM23890 |
| Деталь: | WASHER DRIVE SHAFT |
| Парткод: | 2CK22210 |
| Деталь: | STOPPER PI |
| Парткод: | 2BM17990 |
| Деталь: | JOINT MIX |
| Парткод: | 2CK22010 |
| Деталь: | SPRING JOINT MIX |
| Парткод: | 2CK22040 |
| Деталь: | RING JOINT MIX |
| Парткод: | 2CK22080 |
| Деталь: | DVF KP-1011 ASSY |
| Парткод: | 2CK01150 |
| Деталь: | PLATE DRIVE FEED C |
| Парткод: | 2CK22360 |
| Деталь: | BUSH METAL |
| Парткод: | 2BM07330 |
| Деталь: | GEAR Z22 JOINT BE |
| Парткод: | 2CK22410 |
| Деталь: | SHAFT JOINT BEVEL |
| Парткод: | 2BM22830 |
| Деталь: | SPRING JOINT LOW |
| Парткод: | 2BM22850 |
| Деталь: | GEAR Z25 JOINT |
| Парткод: | 2BM22660 |
| Деталь: | GEAR Z23S |
| Парткод: | 2CK22400 |
| Деталь: | GEAR Z14 Z30 |
| Парткод: | 2BM22630 |
| Деталь: | GEAR Z26 |
| Парткод: | 2BM22620 |
| Деталь: | GEAR Z23JO |
| Парткод: | 2BM22640 |
| Деталь: | GEAR Z33 Z23 |
| Парткод: | 2BM22650 |
| Деталь: | GEAR Z30 Z66H |
| Парткод: | 2BM22580 |
| Деталь: | GEAR Z14 Z36 |
| Парткод: | 2BM22700 |
| Деталь: | PLATE DRIVE FEED B |
| Парткод: | 2CK22350 |
| Деталь: | BUSH SHAFT 6 |
| Парткод: | 2BM22760 |
| Деталь: | GEAR BEVEL Z20 |
| Парткод: | 2BM22680 |
| Деталь: | GEAR Z29JO |
| Парткод: | 2BM22740 |
| Деталь: | Gear Z36 |
| Парткод: | 2BM22610 |
| Деталь: | GEAR Z24 |
| Парткод: | 2BM22600 |
| Деталь: | GEAR Z33 Z47H |
| Парткод: | 2BM22590 |
| Деталь: | CLUTCH REGIST 8 |
| Парткод: | 2CK27580 |
| Деталь: | CLUTCH 26-A |
| Парткод: | 2BM27760 |
| Деталь: | SHAFT JOINT MID |
| Парткод: | 2CK22370 |
| Деталь: | PLATE DRIVE FEED A |
| Парткод: | 2CK22340 |
| Деталь: | GEAR Z27 Z40 |
| Парткод: | 2BM22710 |
| Деталь: | HOUSING CL REGIST |
| Парткод: | 2BM22750 |
| Деталь: | SHAFT JOINT REGIST |
| Парткод: | 2CK22390 |
| Деталь: | SPRING JOINT REGIST |
| Парткод: | 2BM22840 |
| Деталь: | JOINT ROLL REGIST |
| Парткод: | 2BM22790 |
| Деталь: | BUSH CLUTCH D1234 |
| Парткод: | 2BM14060 |
| Деталь: | GEAR Z22 Z27 |
| Парткод: | 2CK22320 |
| Деталь: | CLUTCH 26-I |
| Парткод: | 2CK27530 |
| Деталь: | SHAFT CL MID |
| Парткод: | 2CK22330 |
| Деталь: | GEAR Z14 |
| Парткод: | 2CK22300 |
| Деталь: | GEAR Z23 BEA ASSY |
| Парткод: | 2CK22380 |
| Деталь: | SEAL CLUTH REG |
| Парткод: | 2BM23840 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | SEAL CLUTH D1234 |
| Парткод: | 2BM40150 |
| Деталь: | WIRE SADDLE,LWS-1S |
| Парткод: | M2109180 |
| Деталь: | MOTOR STEP |
| Парткод: | 2CK27510 |
| Деталь: | HOLDER STMOTOR |
| Парткод: | 2BM23610 |
| Деталь: | PLATE DRIVE FUSER A |
| Парткод: | 2BM23510 |
| Деталь: | GEAR Z40JO |
| Парткод: | 2BM23570 |
| Деталь: | GEAR Z51 |
| Парткод: | 2BM23560 |
| Деталь: | PLATE PULLEY |
| Парткод: | 2BM23530 |
| Деталь: | PULLEY BELT |
| Парткод: | 2BM23580 |
| Деталь: | GEAR P50 Z23 |
| Парткод: | 2BM23540 |
| Деталь: | BELT S2M138 |
| Парткод: | 2BM23630 |
| Деталь: | Bushing SBK |
| Парткод: | 5MMM176CJ005 |
| Деталь: | GEAR Z46 JOINT FUSER |
| Парткод: | 2BM23550 |
| Деталь: | BUSH MAG |
| Парткод: | 5MVM170XN002 |
| Деталь: | HOLDER SHAFT FUSER |
| Парткод: | 2BM23520 |
| Деталь: | SHAFT JOINT FUSER ASSY |
| Парткод: | 2BM68240 |
| Деталь: | PLATE DRIVE TK |
| Парткод: | 2BM22860 |
| Деталь: | BUSH POM MID |
| Парткод: | 2BM22770 |
| Деталь: | GEAR Z41 |
| Парткод: | 2BM22940 |
| Деталь: | GEAR Z14 Z40 |
| Парткод: | 2BM22930 |
| Деталь: | GEAR Z23 Z33 |
| Парткод: | 2BM22910 |
| Деталь: | GEAR Z23 TK1 |
| Парткод: | 2BM23690 |
| Деталь: | GEAR Z21 Z36 |
| Парткод: | 2BM22920 |
| Деталь: | GEARZ37BEVELZ25 |
| Парткод: | 2BM23710 |
| Деталь: | SPRING JOINT TK |
| Парткод: | 2BM22990 |
| Деталь: | JOINT SCRAPER TK |
| Парткод: | 2BM22890 |
| Деталь: | JOINT TK FEED |
| Парткод: | 2BM22880 |
| Деталь: | GEAR Z23 TK2 |
| Парткод: | 2BM23700 |
| Деталь: | GEAR Z24L |
| Парткод: | 2BM22950 |
| Деталь: | SHAFT JOINT TK |
| Парткод: | 2BM22980 |
| Деталь: | GEAR Z30 CL TK |
| Парткод: | 2BM22970 |
| Деталь: | CLUTCH 26-G |
| Парткод: | 2BM27950 |
| Деталь: | HOLDER CL TK |
| Парткод: | 2BM22870 |
| Деталь: | SEAL TK |
| Парткод: | 2CK22420 |
| Деталь: | SEAL CLUTCH TK |
| Парткод: | 2BM23920 |
| Деталь: | SHIM 6.2-0.25T |
| Парткод: | C2893950 |
| Деталь: | CONN. CORD HV T2 ASSY |
| Парткод: | 2BM28790 |
| Деталь: | CONN. CORD HV G ASSY |
| Парткод: | 2BM28860 |
| Деталь: | CONN. CORD HV MAIN ASSY |
| Парткод: | 2BM28870 |
| Деталь: | CONN. CORD FEED-HUMIDITY ASSY |
| Парткод: | 2CK27070 |
| Деталь: | CONN. CORD FEED ASSY |
| Парткод: | 2BM28670 |
| Деталь: | CONN. CORD HV CR ASSY |
| Парткод: | 2BM28850 |
| Деталь: | CONN. CORD HV T1 ASSY |
| Парткод: | 2BM28800 |
| Деталь: | CONN. CORD HV BK ASSY |
| Парткод: | 2BM28840 |
| Деталь: | CONN. CORD HV BC ASSY |
| Парткод: | 2BM28830 |
| Деталь: | CONN. CORD HV BM ASSY |
| Парткод: | 2BM28820 |
| Деталь: | CONN. CORD HV BY ASSY |
| Парткод: | 2BM28810 |
| Деталь: | CONN. CORD APC-B ASSY |
| Парткод: | 2CK27000 |
| Деталь: | CONN. CORD PS2-B ASSY |
| Парткод: | 2CK27300 |
| Деталь: | CONN. CORD HEAT CONT-B ASSY |
| Парткод: | 2CK27210 |
| Деталь: | CONN. CORD POWER E.-B ASSY |
| Парткод: | 2CK27200 |
| Деталь: | CONN. CORD SW.RELAY ASSY |
| Парткод: | 2CK27310 |
| Деталь: | CONN. CORD E2P-KTS ASSY |
| Парткод: | 2CK27230 |
| Деталь: | CONN. CORD COVER SW.-B ASSY |
| Парткод: | 2CK27180 |
| Деталь: | CONN. CORD CMT-DRV-HVM ASSY |
| Парткод: | 2CK27100 |
| Деталь: | CONN. CORD DRIVE MAIN ASSY |
| Парткод: | 2BM27610 |
| Деталь: | CONN. CORD KMT-DRMT ASSY |
| Парткод: | 2CK27110 |
| Деталь: | CONN. CORD OP.RERAY-B ASSY |
| Парткод: | 2CK27190 |
| Деталь: | CONN. CORD HV-T2-B ASSY |
| Парткод: | 2CK27160 |
| Деталь: | CONN. CORD PF/DU ASSY |
| Парткод: | 2BM28720 |
| Деталь: | CONN. CORD TRANSFER-B ASSY |
| Парткод: | 2CK27080 |
| Деталь: | CONN. CORD FUSER-B ASSY |
| Парткод: | 2CK27120 |
| Деталь: | CONN. CORD DRUM ASSY |
| Парткод: | 2BM28640 |
| Деталь: | CONN. CORD S02597 ASSY |
| Парткод: | 2BM28760 |
| Деталь: | CONN. CORD DLP YM ASSY |
| Парткод: | 2BM28540 |
| Деталь: | CONN. CORD DLP CK-B ASSY |
| Парткод: | 2CK27020 |
| Деталь: | DR-803B DRIVE UNIT B |
| Парткод: | 2CK93190 |
| Деталь: | DR-803C DRIVE UNIT C |
| Парткод: | 2CK68030 |
| Деталь: | DR-803D DRIVE UNIT D |
| Парткод: | 2CK93200 |
| Деталь: | DR-803A DRIVE UNIT A |
| Парткод: | 2CK93180 |
| Деталь: | MOTOR MAIN |
| Парткод: | 2BM27690 |
| Деталь: | HOLDER ASSY B |
| Парткод: | 2BM22200 |
| Деталь: | PLATE DRIVE MAIN B |
| Парткод: | 2BM22020 |
| Деталь: | GEAR Z144H BT |
| Парткод: | 2BM23870 |
| Деталь: | MOTOR DLP |
| Парткод: | 2BM27700 |
| Деталь: | GEAR Z36H Z117H |
| Парткод: | 2BM22060 |
| Деталь: | BUSH 6-9-4 |
| Парткод: | 2BM22360 |
| Деталь: | EDGING EDS-0607U |
| Парткод: | M2104260 |
| Деталь: | GEAR Z30 Z58H |
| Парткод: | 2CK22060 |
| Деталь: | GEAR Z25 Z29 |
| Парткод: | 2BM22090 |
| Деталь: | GEAR Z23 IDLE |
| Парткод: | 2BM22170 |
| Деталь: | GEAR Z29 IDLE |
| Парткод: | 2BM22100 |
| Деталь: | GEAR Z14 Z29 |
| Парткод: | 2BM22160 |
| Деталь: | GEAR Z43H |
| Парткод: | 2BM22140 |
| Деталь: | GEAR Z30 Z57H |
| Парткод: | 2CK22070 |
| Деталь: | GEAR Z53 |
| Парткод: | 2BM23760 |
| Деталь: | PLATE DRIVE MAIN C |
| Парткод: | 2CK22050 |
| Деталь: | GEAR Z26 IDLE |
| Парткод: | 2BM22110 |
| Деталь: | GEAR Z34 |
| Парткод: | 2BM23750 |
| Деталь: | GEAR Z30 JOINT MIX |
| Парткод: | 2CK22020 |
| Деталь: | BUSH MAIN C |
| Парткод: | 2BM23800 |
| Деталь: | GEAR Z21H Z26 |
| Парткод: | 2BM22150 |
| Деталь: | GEAR Z28 |
| Парткод: | 2BM22180 |
| Деталь: | CLUTCH ASSY 2 |
| Парткод: | 2CK22130 |
| Деталь: | HOLDER ASSY CHY |
| Парткод: | 2CK22150 |
| Деталь: | HOLDER ASSY CHM |
| Парткод: | 2CK22160 |
| Деталь: | HOLDER ASSY CHC |
| Парткод: | 2CK22170 |
| Деталь: | HOLDER ASSY CHK |
| Парткод: | 2CK22140 |
| Деталь: | PLATE DRIVE MAIN A |
| Парткод: | 2CK22030 |
| Деталь: | BUSH CL CAM |
| Парткод: | 2BM22270 |
| Деталь: | SHAFT JOINT CAM |
| Парткод: | 2BM22420 |
| Деталь: | CLUTCH ASSY CAM |
| Парткод: | 2BM22280 |
| Деталь: | SHAFT JOINT SCREW |
| Парткод: | 2BM22430 |
| Деталь: | CLUTCH 26-C |
| Парткод: | 2BM27630 |
| Деталь: | HOUSING CL CAM |
| Парткод: | 2BM22260 |
| Деталь: | SPRING JOINT CAM |
| Парткод: | 2BM22460 |
| Деталь: | JOINT CAM |
| Парткод: | 2BM22330 |
| Деталь: | JOINT ROLL SCREW |
| Парткод: | 2BM22320 |
| Деталь: | ACTUATOR CAM |
| Парткод: | 2BM22350 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 2BM22470 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | SOLENOID CAM |
| Парткод: | 2BM27640 |
| Деталь: | PLATE SENSOR |
| Парткод: | 2BM22380 |
| Деталь: | SHAFT JOINT DRUM A |
| Парткод: | 2CK22430 |
| Деталь: | HOLDER ASSY A |
| Парткод: | 2CK22180 |
| Деталь: | SPRING JOINT DRUM BT |
| Парткод: | 2BM23910 |
| Деталь: | JOINT DRUM BT |
| Парткод: | 2BM23900 |
| Деталь: | PW.BOARD KP-824 ASSY |
| Парткод: | 2BM01170 |
| Деталь: | LID HV UNIT |
| Парткод: | 2BM22500 |
| Деталь: | EARTH DLP |
| Парткод: | 2BM22510 |
| Деталь: | PLATE HV JOINT |
| Парткод: | 2BM22530 |
| Деталь: | EARTH DRUM |
| Парткод: | 2BM22520 |
| Деталь: | PLATE HV DRUM |
| Парткод: | 2BM22540 |
| Деталь: | EARTH DRUM T1 |
| Парткод: | 2BM23810 |
| Деталь: | METAL BUSH KD |
| Парткод: | 5MMM176CJ003 |
| Деталь: | CASE HV JOINT DLP |
| Парткод: | 2BM22490 |
| Деталь: | HOLDER HARNESS D |
| Парткод: | 2BM23730 |
| Деталь: | SOLENOID Y |
| Парткод: | 2BM27650 |
| Деталь: | PLATE SOLENOID |
| Парткод: | 2BM22370 |
| Деталь: | LEVER SOLENOID |
| Парткод: | 2BM22340 |
| Деталь: | SPRING LEVER |
| Парткод: | 2BM22440 |
| Деталь: | SEAL SOLENOID |
| Парткод: | 2BM22480 |
| Деталь: | SOLENOID M |
| Парткод: | 2BM27660 |
| Деталь: | SOLENOID C |
| Парткод: | 2BM27670 |
| Деталь: | SOLENOID K |
| Парткод: | 2BM27680 |
| Деталь: | PLATE DRIVE MAIN D |
| Парткод: | 2BM22040 |
| Деталь: | SPRING HV |
| Парткод: | 2BM23780 |
| Деталь: | PLATE GEAR Z144H BT |
| Парткод: | 2BM23860 |
| Деталь: | JOINT GEAR BT |
| Парткод: | 2BM23890 |
| Деталь: | WASHER DRIVE SHAFT |
| Парткод: | 2CK22210 |
| Деталь: | STOPPER PI |
| Парткод: | 2BM17990 |
| Деталь: | JOINT MIX |
| Парткод: | 2CK22010 |
| Деталь: | SPRING JOINT MIX |
| Парткод: | 2CK22040 |
| Деталь: | RING JOINT MIX |
| Парткод: | 2CK22080 |
| Деталь: | DVF KP-1011 ASSY |
| Парткод: | 2CK01150 |
| Деталь: | PLATE DRIVE FEED C |
| Парткод: | 2CK22360 |
| Деталь: | BUSH METAL |
| Парткод: | 2BM07330 |
| Деталь: | GEAR Z22 JOINT BE |
| Парткод: | 2CK22410 |
| Деталь: | SHAFT JOINT BEVEL |
| Парткод: | 2BM22830 |
| Деталь: | SPRING JOINT LOW |
| Парткод: | 2BM22850 |
| Деталь: | GEAR Z25 JOINT |
| Парткод: | 2BM22660 |
| Деталь: | GEAR Z23S |
| Парткод: | 2CK22400 |
| Деталь: | GEAR Z14 Z30 |
| Парткод: | 2BM22630 |
| Деталь: | GEAR Z26 |
| Парткод: | 2BM22620 |
| Деталь: | GEAR Z23JO |
| Парткод: | 2BM22640 |
| Деталь: | GEAR Z33 Z23 |
| Парткод: | 2BM22650 |
| Деталь: | GEAR Z30 Z66H |
| Парткод: | 2BM22580 |
| Деталь: | GEAR Z14 Z36 |
| Парткод: | 2BM22700 |
| Деталь: | PLATE DRIVE FEED B |
| Парткод: | 2CK22350 |
| Деталь: | BUSH SHAFT 6 |
| Парткод: | 2BM22760 |
| Деталь: | GEAR BEVEL Z20 |
| Парткод: | 2BM22680 |
| Деталь: | GEAR Z29JO |
| Парткод: | 2BM22740 |
| Деталь: | Gear Z36 |
| Парткод: | 2BM22610 |
| Деталь: | GEAR Z24 |
| Парткод: | 2BM22600 |
| Деталь: | GEAR Z33 Z47H |
| Парткод: | 2BM22590 |
| Деталь: | CLUTCH REGIST 8 |
| Парткод: | 2CK27580 |
| Деталь: | CLUTCH 26-A |
| Парткод: | 2BM27760 |
| Деталь: | SHAFT JOINT MID |
| Парткод: | 2CK22370 |
| Деталь: | PLATE DRIVE FEED A |
| Парткод: | 2CK22340 |
| Деталь: | GEAR Z27 Z40 |
| Парткод: | 2BM22710 |
| Деталь: | HOUSING CL REGIST |
| Парткод: | 2BM22750 |
| Деталь: | SHAFT JOINT REGIST |
| Парткод: | 2CK22390 |
| Деталь: | SPRING JOINT REGIST |
| Парткод: | 2BM22840 |
| Деталь: | JOINT ROLL REGIST |
| Парткод: | 2BM22790 |
| Деталь: | BUSH CLUTCH D1234 |
| Парткод: | 2BM14060 |
| Деталь: | GEAR Z22 Z27 |
| Парткод: | 2CK22320 |
| Деталь: | CLUTCH 26-I |
| Парткод: | 2CK27530 |
| Деталь: | SHAFT CL MID |
| Парткод: | 2CK22330 |
| Деталь: | GEAR Z14 |
| Парткод: | 2CK22300 |
| Деталь: | GEAR Z23 BEA ASSY |
| Парткод: | 2CK22380 |
| Деталь: | SEAL CLUTH REG |
| Парткод: | 2BM23840 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | SEAL CLUTH D1234 |
| Парткод: | 2BM40150 |
| Деталь: | WIRE SADDLE,LWS-1S |
| Парткод: | M2109180 |
| Деталь: | MOTOR STEP |
| Парткод: | 2CK27510 |
| Деталь: | HOLDER STMOTOR |
| Парткод: | 2BM23610 |
| Деталь: | PLATE DRIVE FUSER A |
| Парткод: | 2BM23510 |
| Деталь: | GEAR Z40JO |
| Парткод: | 2BM23570 |
| Деталь: | GEAR Z51 |
| Парткод: | 2BM23560 |
| Деталь: | PLATE PULLEY |
| Парткод: | 2BM23530 |
| Деталь: | PULLEY BELT |
| Парткод: | 2BM23580 |
| Деталь: | GEAR P50 Z23 |
| Парткод: | 2BM23540 |
| Деталь: | BELT S2M138 |
| Парткод: | 2BM23630 |
| Деталь: | Bushing SBK |
| Парткод: | 5MMM176CJ005 |
| Деталь: | GEAR Z46 JOINT FUSER |
| Парткод: | 2BM23550 |
| Деталь: | BUSH MAG |
| Парткод: | 5MVM170XN002 |
| Деталь: | HOLDER SHAFT FUSER |
| Парткод: | 2BM23520 |
| Деталь: | SHAFT JOINT FUSER ASSY |
| Парткод: | 2BM68240 |
| Деталь: | PLATE DRIVE TK |
| Парткод: | 2BM22860 |
| Деталь: | BUSH POM MID |
| Парткод: | 2BM22770 |
| Деталь: | GEAR Z41 |
| Парткод: | 2BM22940 |
| Деталь: | GEAR Z14 Z40 |
| Парткод: | 2BM22930 |
| Деталь: | GEAR Z23 Z33 |
| Парткод: | 2BM22910 |
| Деталь: | GEAR Z23 TK1 |
| Парткод: | 2BM23690 |
| Деталь: | GEAR Z21 Z36 |
| Парткод: | 2BM22920 |
| Деталь: | GEARZ37BEVELZ25 |
| Парткод: | 2BM23710 |
| Деталь: | SPRING JOINT TK |
| Парткод: | 2BM22990 |
| Деталь: | JOINT SCRAPER TK |
| Парткод: | 2BM22890 |
| Деталь: | JOINT TK FEED |
| Парткод: | 2BM22880 |
| Деталь: | GEAR Z23 TK2 |
| Парткод: | 2BM23700 |
| Деталь: | GEAR Z24L |
| Парткод: | 2BM22950 |
| Деталь: | SHAFT JOINT TK |
| Парткод: | 2BM22980 |
| Деталь: | GEAR Z30 CL TK |
| Парткод: | 2BM22970 |
| Деталь: | CLUTCH 26-G |
| Парткод: | 2BM27950 |
| Деталь: | HOLDER CL TK |
| Парткод: | 2BM22870 |
| Деталь: | SEAL TK |
| Парткод: | 2CK22420 |
| Деталь: | SEAL CLUTCH TK |
| Парткод: | 2BM23920 |
| Деталь: | SHIM 6.2-0.25T |
| Парткод: | C2893950 |
| Деталь: | FK-803(E) FUSER UNIT (E) |
| Парткод: | 2CK93130 |
| Деталь: | FK-803(U) FUSER UNIT (U) |
| Парткод: | 2CK93140 |
| Деталь: | HANDLE GEAR |
| Парткод: | 2BM20500 |
| Деталь: | COVER REAR FUSER |
| Парткод: | 2BM20380 |
| Деталь: | CONN.CORD INNER FUSER |
| Парткод: | 2BM27930 |
| Деталь: | SPRING CONNECTOR |
| Парткод: | 2BM20430 |
| Деталь: | BKT LAMP REAR |
| Парткод: | 2CK20170 |
| Деталь: | GEAR INPUT Z30 |
| Парткод: | 2CK20110 |
| Деталь: | GEAR FUSER Z43 |
| Парткод: | 2CK20100 |
| Деталь: | BEARING 6806ZNR |
| Парткод: | 2CK20030 |
| Деталь: | GEAR FUSER IDLEZ24 |
| Парткод: | 2CK20220 |
| Деталь: | GEAR EXIT ROLL Z18 |
| Парткод: | 2BM20520 |
| Деталь: | BUSH CONDUCTIVE |
| Парткод: | 2CK16010 |
| Деталь: | FRAME REAR FUSER |
| Парткод: | 2CK20060 |
| Деталь: | PLATE PRESS REAR |
| Парткод: | 2CK20080 |
| Деталь: | SPRING PRESSURE |
| Парткод: | 2CK20320 |
| Деталь: | SHAFT PRESS FUSER |
| Парткод: | 2CK20120 |
| Деталь: | BUSH HEAT ROLLER |
| Парткод: | 2CK20040 |
| Деталь: | ROLLER EXIT |
| Парткод: | 2CK20090 |
| Деталь: | ROLLER HEAT |
| Парткод: | 2CK20010 |
| Деталь: | ROLLER PRESS |
| Парткод: | 2CK20020 |
| Деталь: | FRAME TOP FUSER |
| Парткод: | 2BM20270 |
| Деталь: | BKT THERMOSTAT |
| Парткод: | 2BM20310 |
| Деталь: | NUT FUSER A |
| Парткод: | 5MMT163SN006 |
| Деталь: | BKT THERMISTER UP |
| Парткод: | 2BM20290 |
| Деталь: | THERMISTOR UP |
| Парткод: | 2BM20830 |
| Деталь: | THERMOSTAT |
| Парткод: | 5EYFFQ17001++01 |
| Деталь: | HOLDER HERNESS TOP R |
| Парткод: | 2BM20280 |
| Деталь: | GUIDE UPPER ENTRANCE |
| Парткод: | 2CK20190 |
| Деталь: | GUIDE LOWER EXIT |
| Парткод: | 2CK20210 |
| Деталь: | GUIDE ENTRANCE LOW |
| Парткод: | 2BM20330 |
| Деталь: | HOLDER HARNESS RR |
| Парткод: | 2BM20070 |
| Деталь: | HOLDER HARNESS R.F |
| Парткод: | 2BM20060 |
| Деталь: | THERMISTOR LOW |
| Парткод: | 2BM20840 |
| Деталь: | Frame Bottom |
| Парткод: | 2BM20050 |
| Деталь: | COVER BOTTOM FUSER |
| Парткод: | 2BM20360 |
| Деталь: | HOLDER HARNESS LOWER |
| Парткод: | 2BM20080 |
| Деталь: | NUT FUSER |
| Парткод: | 5MMK116SZ001 |
| Деталь: | LAMP HEATER UP 240 |
| Парткод: | 2CK20270 |
| Деталь: | LAMP HEATER UP 120 |
| Парткод: | 2CK20250 |
| Деталь: | LAMP HEATER LOW 240 |
| Парткод: | 2CK20280 |
| Деталь: | LAMP HEATER LOW 120 |
| Парткод: | 2CK20260 |
| Деталь: | PLATE PRESS FRONT |
| Парткод: | 2CK20070 |
| Деталь: | FRAME FRONT FUSER |
| Парткод: | 2CK20050 |
| Деталь: | BKT LAMP FRONT |
| Парткод: | 2CK20160 |
| Деталь: | FSR KP-997 ASSY |
| Парткод: | 2CK01080 |
| Деталь: | COVER FRONT FUSER |
| Парткод: | 2CK20180 |
| Деталь: | STAY LOWER SEPARATOR |
| Парткод: | 2CK20150 |
| Деталь: | SEPARETOR LOW |
| Парткод: | 2BM20210 |
| Деталь: | SPRING SEPARATOR |
| Парткод: | 2CK20340 |
| Деталь: | SPRING SEPARETOR |
| Парткод: | 2BM20260 |
| Деталь: | SHEET PROTECT STAY |
| Парткод: | 2CK20330 |
| Деталь: | STAY UPPER SEPARATOR |
| Парткод: | 2CK20140 |
| Деталь: | BKT SEPARATOR UP |
| Парткод: | 2BM20220 |
| Деталь: | LABEL CAUTION S |
| Парткод: | 2BM42710 |
| Деталь: | SEPARATOR UP |
| Парткод: | 2BM20240 |
| Деталь: | COVER REAR FIX CLN |
| Парткод: | 2CK20550 |
| Деталь: | COVER UPPER FUSER |
| Парткод: | 2CK20530 |
| Деталь: | COVER FRONT FIX CLN |
| Парткод: | 2CK20540 |
| Деталь: | STUD SCREW 465 |
| Парткод: | 2BM41080 |
| Деталь: | LID FUSER CLN |
| Парткод: | 2CK20560 |
| Деталь: | LABEL OPERATE FUSER |
| Парткод: | 2CK20300 |
| Деталь: | LABEL CAUTION FUSER |
| Парткод: | 2BM05090 |
| Деталь: | SPRING EXIT |
| Парткод: | 2BM20790 |
| Деталь: | Bush SP |
| Парткод: | 2BM20610 |
| Деталь: | SHAFT EXIT |
| Парткод: | 5MMT622SN003 |
| Деталь: | PULLEY EXIT |
| Парткод: | 5MVM176DB018 |
| Деталь: | COVER EXIT FUSER |
| Парткод: | 2BM20390 |
| Деталь: | TR-803P PRI TRANSFER UNIT |
| Парткод: | 2CK93110 |
| Деталь: | COVER IMAGE R |
| Парткод: | 2BM16160 |
| Деталь: | JOINT CAM CL |
| Парткод: | 2BM16200 |
| Деталь: | PLATE BIAS FLICKER B |
| Парткод: | 2BM16460 |
| Деталь: | SPRING IMAGE PRESS |
| Парткод: | 2CK16220 |
| Деталь: | SPRING PLATE IMAGE |
| Парткод: | 2BM16990 |
| Деталь: | PULLY RAIL |
| Парткод: | 2CK16020 |
| Деталь: | STOPPER GUIDE |
| Парткод: | 2BM16500 |
| Деталь: | BUSH CONDUCTIVE |
| Парткод: | 2CK16010 |
| Деталь: | EARTH FRAME |
| Парткод: | 2BM16930 |
| Деталь: | CAM PRESS F |
| Парткод: | 2BM16340 |
| Деталь: | GEAR LEVER FRAME |
| Парткод: | 2BM16010 |
| Деталь: | HOLDER CL F |
| Парткод: | 2BM16210 |
| Деталь: | LEVER CL RELEASE A |
| Парткод: | 2BM16420 |
| Деталь: | LEVER CL RELEASE B |
| Парткод: | 2BM16430 |
| Деталь: | STOPPER LEVER IMAGE |
| Парткод: | 2BM16300 |
| Деталь: | SPRING STOPPER LEVER |
| Парткод: | 2BM16310 |
| Деталь: | LEVER LOCK |
| Парткод: | 2BM16410 |
| Деталь: | SPRING LEVER LOCK |
| Парткод: | 2BM16920 |
| Деталь: | STOPPER SPRING |
| Парткод: | 2BM16480 |
| Деталь: | SPRING LEVER FRAME |
| Парткод: | 2BM16490 |
| Деталь: | COVER IMAGE F |
| Парткод: | 2BM16290 |
| Деталь: | LABEL IMAGE C |
| Парткод: | 2BM16550 |
| Деталь: | LEVER FRAME IMAGE |
| Парткод: | 2BM16020 |
| Деталь: | LABEL IMAGE A |
| Парткод: | 2BM16530 |
| Деталь: | LABEL IMAGE B |
| Парткод: | 2BM16540 |
| Деталь: | BC-803 BRUSH CLEANER |
| Парткод: | 2CK93240 |
| Деталь: | JOINT SCREW |
| Парткод: | 2BM16660 |
| Деталь: | BUSH SCREW R |
| Парткод: | 2BM16690 |
| Деталь: | SCREW CLEANER |
| Парткод: | 2BM16640 |
| Деталь: | SHAFT SCREW |
| Парткод: | 2BM16760 |
| Деталь: | COVER CLEANER R |
| Парткод: | 2BM16630 |
| Деталь: | SPRING SHUTTER |
| Парткод: | 2BM16590 |
| Деталь: | PLATE BIAS SWEEP |
| Парткод: | 2BM16870 |
| Деталь: | BUSH EARTH |
| Парткод: | 2BM16900 |
| Деталь: | SHUTTER CLEANER |
| Парткод: | 2BM16570 |
| Деталь: | BUSH BRUSH R |
| Парткод: | 2BM16670 |
| Деталь: | BUSH SWEEP R |
| Парткод: | 2CK16130 |
| Деталь: | SEAL SHUTTER |
| Парткод: | 2BM16580 |
| Деталь: | SEAL SWEEP SIDE F |
| Парткод: | 2CK16170 |
| Деталь: | FRAME CLEANER |
| Парткод: | 2BM16611 |
| Деталь: | GUIDE TONER |
| Парткод: | 2BM16741 |
| Деталь: | SEAL GUIDE TONER |
| Парткод: | 2BM16780 |
| Деталь: | BLADE CLEANER ASSY |
| Парткод: | 2BM68270 |
| Деталь: | ROLLER SWEEP |
| Парткод: | 2CK16150 |
| Деталь: | BRUSH FUR |
| Парткод: | 2BM16600 |
| Деталь: | BUSH BRUSH F |
| Парткод: | 2BM16680 |
| Деталь: | GEAR BRUSH Z19 |
| Парткод: | 2BM16730 |
| Деталь: | BUSH SWEEP F |
| Парткод: | 2CK16140 |
| Деталь: | BUSH SCREW F |
| Парткод: | 2BM16700 |
| Деталь: | GEAR SCREW Z19 |
| Парткод: | 2BM16860 |
| Деталь: | COVER CLEANER F |
| Парткод: | 2BM16620 |
| Деталь: | PLATE GUIDE SWEEP |
| Парткод: | 2BM16980 |
| Деталь: | SEAL GUIDE SWEEP |
| Парткод: | 2CK16180 |
| Деталь: | PUSH NUT |
| Парткод: | 2BM45020 |
| Деталь: | DV-803C DEVELOPER CYAN |
| Парткод: | 2CK93070 |
| Деталь: | GEAR Z15-8 D123 |
| Парткод: | 2CK1428 |
| Деталь: | GEAR Z30H-Z17H D3 |
| Парткод: | 2CK1442 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM4006 |
| Деталь: | JOINT D1234 |
| Парткод: | 2CK1430 |
| Деталь: | BUSH CLUTCH D1234 |
| Парткод: | 2BM1406 |
| Деталь: | BKT CLUTCH D3 |
| Парткод: | 2CK1412 |
| Деталь: | CLUTCH 26-F |
| Парткод: | 2BM2749 |
| Деталь: | GEAR Z15-Z10 D123 |
| Парткод: | 2CK1429 |
| Деталь: | SHAFT CLUTCH D1234 |
| Парткод: | 2CK1431 |
| Деталь: | GEAR Z14D-8 D1234 |
| Парткод: | 2CK1433 |
| Деталь: | PANEL ASSY ENGLISH |
| Парткод: | 2BM68010 |
| Деталь: | PANEL ASSY FRENCH |
| Парткод: | 2BM68020 |
| Деталь: | PANEL ASSY ITALIAN |
| Парткод: | 2BM68030 |
| Деталь: | PANEL KEY ENGLISH |
| Парткод: | 2BM04120 |
| Деталь: | PANEL KEY FRENCH |
| Парткод: | 2BM04130 |
| Деталь: | PANEL KEY ITALIAN |
| Парткод: | 2BM04140 |
| Деталь: | PANEL LCD ASSY |
| Парткод: | 2BM00870 |
| Деталь: | KEY TOP ASSY |
| Парткод: | 2BM68050 |
| Деталь: | LENS LED |
| Парткод: | 2BM04080 |
| Деталь: | HOLDER PANEL PWB |
| Парткод: | 2BM04040 |
| Деталь: | KEY TOP1 |
| Парткод: | 2BM04050 |
| Деталь: | KEY TOP2 |
| Парткод: | 2BM04060 |
| Деталь: | KEY TOP3 |
| Парткод: | 2BM04070 |
| Деталь: | P.W.BOARD KP-805 ASSY |
| Парткод: | 2BM01080 |
| Деталь: | PLATE EARTH PANEL |
| Парткод: | 2BM04300 |
| Деталь: | COVER TOP |
| Парткод: | 2BM04010 |
| Деталь: | STOPPER PAPER |
| Парткод: | 2BM04020 |
| Деталь: | SP PRESS2 DLP |
| Парткод: | 2BM04030 |
| Деталь: | COVER REAR |
| Парткод: | 2CK04030 |
| Деталь: | PROTECTOR OZONE |
| Парткод: | 2BM04270 |
| Деталь: | COVER RIGHT |
| Парткод: | 2BM04150 |
| Деталь: | PLATE EARTH RC |
| Парткод: | 2BM04290 |
| Деталь: | SUPPORT COVER ASSY |
| Парткод: | 2BM04160 |
| Деталь: | COVER LEFT |
| Парткод: | 2BM04170 |
| Деталь: | COVER FRONT ASSY |
| Парткод: | 2CK00010 |
| Деталь: | COVER FRONT |
| Парткод: | 2CK04010 |
| Деталь: | PLATE MAGCHATCH |
| Парткод: | 2BM04100 |
| Деталь: | BAND COVER |
| Парткод: | 2BM04280 |
| Деталь: | LABEL DIAGRAM D |
| Парткод: | 2CK05050 |
| Деталь: | LABEL DIAGRAM C |
| Парткод: | 2CK05060 |
| Деталь: | LABEL DIAGRAM B |
| Парткод: | 2BM05020 |
| Деталь: | SEAL COLOR SYMBOL |
| Парткод: | 2CK05070 |
| Деталь: | DV-803M DEVELOPER MAGENTA |
| Парткод: | 2CK93050 |
| Деталь: | SHAFT GEAR D12 |
| Парткод: | 2CK1424 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM4006 |
| Деталь: | JOINT D1234 |
| Парткод: | 2CK1430 |
| Деталь: | BUSH CLUTCH D1234 |
| Парткод: | 2BM1406 |
| Деталь: | Bush |
| Парткод: | 2BM1453 |
| Деталь: | BKT CLUTCH D2 |
| Парткод: | 2CK1408 |
| Деталь: | CLUTCH 26-E |
| Парткод: | 2BM2742 |
| Деталь: | GEAR Z14-8 JOINT D12 |
| Парткод: | 2CK1443 |
| Деталь: | GEAR Z30H-Z17H D12 |
| Парткод: | 2CK1425 |
| Деталь: | GEAR Z15-Z10 D123 |
| Парткод: | 2CK1429 |
| Деталь: | SHAFT CLUTCH D1234 |
| Парткод: | 2CK1431 |
| Деталь: | GEAR Z14D-8 D1234 |
| Парткод: | 2CK1433 |
| Деталь: | GEAR Z15-8 D123 |
| Парткод: | 2CK1428 |
| Деталь: | DK-803 DRUM UNIT |
| Парткод: | 2CK93010 |
| Деталь: | GEAR Z17H CLN |
| Парткод: | 2BM18080 |
| Деталь: | GEAR Z17HZ22H IDLE |
| Парткод: | 2BM18380 |
| Деталь: | GEAR Z28HZ28H DRUM BT |
| Парткод: | 2BM19140 |
| Деталь: | GEAR Z16S CLN |
| Парткод: | 2BM18140 |
| Деталь: | GEAR Z18S SCREW |
| Парткод: | 2BM18130 |
| Деталь: | MC-803 MAIN CHARGER ASSY |
| Парткод: | 2CK93230 |
| Деталь: | ECU KP-992 ASSY E |
| Парткод: | 2CK01060 |
| Деталь: | ECU KP-992 ASSY U |
| Парткод: | 2CK01270 |
| Деталь: | EDGING EDS-1717U |
| Парткод: | M2104220 |
| Деталь: | BOX ENGINE |
| Парткод: | 2CK26050 |
| Деталь: | RAIL PWB |
| Парткод: | 2BM26050 |
| Деталь: | BOX CONTROLLER ASSY |
| Парткод: | 2CK26060 |
| Деталь: | RER KP-993 ASSY |
| Парткод: | 2CK01070 |
| Деталь: | P.W.BOARD ASSY |
| Парткод: | 2CK01300 |
| Деталь: | RAIL OPTION A |
| Парткод: | 2BL26210 |
| Деталь: | RAIL OPTION B |
| Парткод: | 2BL26220 |
| Деталь: | PANEL CONTROLLER |
| Парткод: | 2CK26010 |
| Деталь: | PLATE OPTION |
| Парткод: | 5MMS636SD009 |
| Деталь: | SCREW OP |
| Парткод: | 5MMT263SN012 |
| Деталь: | GUIDE CF CARD |
| Парткод: | 5MVX621SH003 |
| Деталь: | PLATE CONTROLLER A |
| Парткод: | 2BM42510 |
| Деталь: | FAN PSU |
| Парткод: | 2CK27630 |
| Деталь: | POWER SUPPLY 200 UNIT |
| Парткод: | 2CK01250 |
| Деталь: | POWER SUPPLY 120 UNIT |
| Парткод: | 2CK01260 |
| Деталь: | AC SWITCH |
| Парткод: | 2CK27600 |
| Деталь: | CONN.CORD PS1-B ASSY |
| Парткод: | 2CK27220 |
| Деталь: | P.W.BOARD ASSY |
| Парткод: | 2CK01320 |
| Деталь: | FAN MOTOR |
| Парткод: | 2CK26030 |
| Деталь: | SEAL BOX C |
| Парткод: | 2BM26220 |
| Деталь: | SEAL EARTH PWB |
| Парткод: | 2CK26070 |
| Деталь: | SHIELD FORM GASKET L |
| Парткод: | 2CK27680 |
| Деталь: | SHIELD FORM GASKET |
| Парткод: | 2BM26200 |
| Деталь: | SHIELD FORM GASKET 7 |
| Парткод: | 2BM26210 |
| Деталь: | SHIELD FORM GASKET 1 |
| Парткод: | 2BM26160 |
| Деталь: | SHIELD FORM GASKET 3 |
| Парткод: | 2BM26180 |
Коды ошибок
0121
0440
0450
0460
1010
1020
1030
1040
1050
1060
1210
2000
2010
2020
2101
2102
2111
2112
2121
2122
2320
2340
2500
2510
2520
4000
4200
5300
6000
6010
6020
6030
6040
6100
6110
6120
6130
6140
7001
7002
7003
7004
7101
7102
7103
7104
7301
7700 ... 7710
8010
8020
8140
8170
8210
8230
8290
8510
8900
F000
F010
F020
F030
F040
F050
F060
F070
Описание
| Error code: | 0121 |
| Description: | Thermistor Error (Dryer) Thermistor of the Dryer doesn`t work correctly |
| Causes: | Thermistor of the Dryer is broken. There is a cut-line/short in the wiring of the Thermistor. |
| Remedy: | 1) Check the wirings of Dryer 2) Thermistor Replacement |
| Error code: | 0440 |
| Description: | Communication error between printer and document finisher/ mailbox sorter • The CPU (U2) of engine controller PWB (KP-992) does not communicate with the DF-31 document finisher/SO-30 mailbox sorter normally. • The ASIC (U8) of engine controller PWB (KP-992) does not communicate to the DF-31 document finisher/SO-30 mailbox sorter normally. |
| Causes: | Defective engine controller PWB (KP-992). Defective main PWB of DF-31 document finisher/SO-30 mailbox sorter. Defective paper feeder/options relay PWB (KP-995). Defective signal cable between printer and DF-31 document finisher/ SO-30 mailbox sorter. Defective harness (2CK2719) between engine controller PWB (KP-992) and paper feeder/options relay PWB (KP- 995), or poor contact of the connector terminals. Defective document finisher interface PWB. Defective harness (2CK2727) between document finisher interface PWB and engine controller PWB (KP- 992), or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the main PWB of DF-31 document finisher/SO-30 mailbox sorter. See DF-31 document finisher/SO-30 mailbox sorter’s service manual. Replace the paper feeder/options relay PWB (KP-995). Replace the signal cable between printer and DF-31 document finisher/SO-30 mailbox sorter. Check the continuity of the harness (2CK2719). Check the insertion of connectors. Replace the document finisher interface PWB. Check the continuity of the harness (2CK2727). Check the insertion of connectors. |
| Error code: | 0450 |
| Description: | Communication error between printer and bulk stacker • The CPU (U2) of engine controller PWB (KP-992) does not communicate with the ST-30 bulk stacker normally. |
| Causes: | Defective engine controller PWB (KP-992). Defective main board of ST-30 bulk stacker. Defective paper feeder/options relay PWB (KP- 995). Defective signal cable between ST-30 bulk stacker. Defective harness (2CK2719) between engine controller PWB (KP-992) and paper feeder/ options relay PWB (KP-995), or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the main board of ST-30 bulk stacker. See ST-30 bulk stacker’s service manual. Replace the paper feeder/options relay PWB (KP-995). Replace the signal cable between printer and ST-30 bulk stacker. Check the continuity of the harness (2CK2719). Check the insertion of connectors. |
| Error code: | 0460 |
| Description: | Communication error between printer and duplex unit • The CPU (U2) of engine controller PWB (KP-992) does not communicate with the PD-800 duplex unit normally. |
| Causes: | Defective engine controller PWB (KP-992). Defective main board of PD-800 duplex unit. Defective paper feeder/options relay PWB (KP- 995). Defective connection printer and PD-800 duplex unit. Defective harness (2CK2719) between engine controller PWB (KP-992) and paper feeder/ options relay PWB (KP-995), or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the main board of duplex unit PD- 30. See PD-800 duplex unit’s service manual. Replace the paper feeder/options relay PWB (KP-995). Reinstall PD-800 duplex unit. Check the continuity of the harness (2CK2719). Check the insertion of connectors. |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1040 |
| Display: | GL2: W0501 The memory is full. |
| Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1050 |
| Display: | Blue platen switch is dirty. Please clean the switch. |
| Description: | SM lift motor error (side multi tray) After cassette 5 is inserted, SM lift sensor does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor Defective SM lift motor. Defective SM main PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. SM Lift motor 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM Lift motor and SM main PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SM Lift motor. SM Lift sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM Lift sensor and SM main PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the SM Lift sensor. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1060 |
| Description: | PF lift motor 1 error (side paper feeder) After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. *:The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 1 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. PF Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor1 and PF main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor 1. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1210 |
| Description: | Mode Select An invalid print mode was selected in the print command. |
| Causes: | Defective side registration home position sensor. Defective side registration motor. Defective engine controller PWB (KP-992). |
| Remedy: | Resend the print job. If the problem remains, then reinstall the printer driver. Service: Resend the print job. If the problem remains, then reinstall the print driver. |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 2010 |
| Display: | Paper loaded askew. Press Load/Eject and reload the paper. |
| Description: | Main motor startup error Main motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Main motor. Engine PWB |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC13) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2020 |
| Description: | Main drive motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency since ASIC (U8) on the engine controller PWB (KP-992) has issued a motor activation signal to the main drive motor.r. |
| Causes: | Defective main drive motor. Excessive torque for driving drum unit or primary transfer unit. (Overloaded by a damaged gear.) Defective harness (2CK2711) between engine controller PWB (KP-992) and main drive motor, or poor contact of the connector terminals. |
| Remedy: | Replace the main drive motor. Check if the drum unit or primary transfer unit rotates smoothly. Check for broken gears. Replace if any. Check the continuity of the harness (2CK2711). Check the insertion of connectors. |
| Error code: | 2101 |
| Description: | Developer motor error After developer motor is driven, the ready signal does not turn to L within 2 s. After developer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor. Defective engine PWB. |
| Remedy: | Developer unit 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor 1. To check the motor operation, execute DLP(K) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor and Feed PWB 1 (YC8) Feed PWB 1 (YC2) and Engine PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor. Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2102 |
| Description: | Developer motor C error After developer motor C is driven, the ready signal does not turn to L within 5 s. After developer motor C is stabilized, the ready signal is at the H level for 5 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor C. Defective engine PWB. |
| Remedy: | Developer unit C 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor C 1. To check the motor operation, execute DLP(C) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor C and Motor control PWB (YC7) Motor control PWB (YC3) and Engine PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor C. Motor control PWB Replace the Motor control PWB Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2111 |
| Description: | Developer motor startup error (C,M,Y) After the motor starting, the stable signal is not turned ON within 3 s. |
| Remedy: | Developer unit 1. Check that the developer roller can be rotated by hand, and if it is locked, replace the developer unit. Developer motor 1. Check if the couplings and gears rotate smoothly, and if necessary replace them. 2. Reinsert the connector. 3. Check continuity within the connector wire. If none, replace the wire. Developer motor and Engine relay PWB (YC12) Engine relay PWB (YC1) and Main/ Engine PWB (YC4) 4. Replace the developer motor Engine relay PWB Replace the engine relay PWB. Main/Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the Main/Engine PWB. |
| Error code: | 2112 |
| Description: | Developer motor startup error (M/C/Y) After the motor starts up, the ready signal is not turned ON for continuous 2 s |
| Causes: | Defective connector cable or poor contact in the connector Defective drive transmission system. Defective motor. Defective PWB. |
| Remedy: | Developer unit 1. Check that the developer roller can be rotated by hand, and if it is locked, replace the developer unit. Developer motor 1. Check if the couplings and gears rotate smoothly, and if necessary replace them. 2. Reconnect the connector if its connection is loose. 3. Check the continuity within the connector wire. If none, replace the wire. Developer motor - Engine PWB(YC16): 30 ppm model - Engine PWB(YC23): 35/40 ppm models 4. Replace the developer motor. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 2121 |
| Description: | Black developer drive motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency when ASIC (U7) on the engine controller PWB (KP-992) has issued a motor activation signal to the black developer drive motor. |
| Causes: | Defective engine controller PWB (KP-992). Defective black developer drive motor. Excessive torque for driving black developer. (Overloaded by a damaged gear.) Defective harness (2CK2711) between engine controller PWB (KP-992) and black developer, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the black developer drive motor. Check if the black developer rotates smoothly. Check for broken gears. Replace if any. Check the continuity of the harness (2CK2711). Check the insertion of connectors. |
| Error code: | 2122 |
| Description: | Color developers drive motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency when ASIC (U8) on the engine controller PWB (KP-992) has issued a motor activation signal to the drive motor that drives the color developers. |
| Causes: | Defective engine controller PWB (KP-992). Defective color developers drive motor. Excessive torque for driving color developers. (Overloaded by a damaged gear.) Defective harness (2CK2710) between engine controller PWB (KP-992) and color developers, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the color developers drive motor. Check if the yellow, magenta, and cyan developers rotate smoothly. Check for broken gears. Replace if any. Check the continuity of the harness (2CK2710). Check the insertion of connectors. |
| Error code: | 2320 |
| Description: | Fuser drive motor error • The fuser control system does not operate normally. |
| Causes: | Defective engine controller PWB (KP-992). |
| Remedy: | Replace the engine controller PWB (KP- 992). |
| Error code: | 2340 |
| Description: | Fuser pressure release motor time-out error When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6 s. |
| Causes: | Defective connector cable or poor contact in the connector.Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and engine PWB (YC38) Defective drive transmission system of the fuser pressure release motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective fuser pressure release motor. Replace the fuser pressure release motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2510 |
| Description: | Paper feed motor startup error Paper feed motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Paper feed motor. Engine PWB |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Engine PWB (YC13) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2520 |
| Description: | Paper feed motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency within the predetermined period when ASIC (U2) on the engine controller PWB (KP-992) has issued a motor activation signal to the paper feed motor. |
| Causes: | Defective engine controller PWB (KP-992). Defective paper feed motor. Excessive torque for driving paper feed unit. (Overloaded by a damaged gear.) Defective harness (2CK2707) between engine controller PWB (KP-992) and paper feed motor, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the paper feed motor. Check if the paper feed unit rotates smoothly. Check for broken gears. Replace if any. Check the continuity of the harness (2CK2707). Check the insertion of connectors. |
| Error code: | 4000 |
| Display: | Supplies Drum End Soon. |
| Description: | Command Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 4200 |
| Display: | Supplies Replace Drum |
| Description: | BD steady-state error The BD signal is not detected. |
| Causes: | APC PWB (LSU). Main/Engine PWB. |
| Remedy: | APC PWB (LSU) 1. Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in. Laser scanner unit and main/engine PWB (YC2010) 2. If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring. 3. Replace the laser scanner unit. Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. |
| Error code: | 5300 |
| Description: | Eraser lamp broken detection • The current at the correct level is not detected when ASIC (U8) on the engine controller PWB (KP-992) generates the signal to activate the eraser lamp. |
| Causes: | Defective engine controller PWB (KP-992). Defective drum unit (eraser lamp or drum PWB [KP- 813]). Defective harness (2BM2864) between engine controller PWB (KP-992) and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the drum unit. Check the continuity of the harness (2BM2864). Check the insertion of connectors. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6010 |
| Description: | Abnormally high fuser thermistor temperature The fuser Abnormally high signal is detected for 60 s or more. |
| Causes: | Defective PWB. |
| Remedy: | Defective PWB. Replace the power source PWB or engine PWB and check for correct operation. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6040 |
| Description: | Fuser heater error Input from fuser center thermistor 1 is abnormal value continuously for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Center thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6100 |
| Description: | Broken fuser heater wire Fuser thermistor 5 won’t reach the reference temperature in 480 s after shifting to low power mode. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6110 |
| Description: | Press/heat roller heating time-out 2 • The temperature on the press/heat toller does not reach the correct temperature within the predetermined period after self-diagnostic code 6100 is cleared. The period for detection is longer than the condition for selfdiagnostics code 6100. |
| Causes: | Defective engine controller PWB (KP-992). Defective lower heater lamp. Defective lower thermostat. Defective fuser PWB (KP-997). Defective lower fuser thermistor, or fitting is not proper. Defective AC power source (Abnormal low voltage). Defective harness (2CK2719, 2CK2712) between engine controller PWB (KP-992) and paper feeder/ options relay PWB (KP- 995) and fuser unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the fuser unit (lower heater lamp). Replace the fuser unit (lower thermostat). Replace the fuser unit (fuser PWB [KP- 997]). Replace the fuser unit (upper fuser thermistor). Connect to the proper AC power source. Check the continuity of the harness (2CK2719, 2CK2712). Check the insertion of connectors. |
| Error code: | 6120 |
| Description: | Abnormally high fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature higher than 190°C/ 374°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 5. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6130 |
| Description: | Broken fuser press thermistor 5 wire The input from the fuser press thermistor 5 has been less than 30°C/ 86°F (A/D: greater thann992) for 60 seconds continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) Fuser IH PWB(YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6140 |
| Description: | Lower fuser thermistor abnormal temperature detection • The temperature detection output from the lower fuser thermistor is out of the normal range. |
| Causes: | Defective engine controller PWB (KP-992). Defective fuser PWB (KP-997). Defective lower fuser thermistor, or fitting is not proper. Defective harness (2CK2719, 2CK2712) between engine controller PWB (KP-992) and paper feeder/ options relay PWB (KP-995) and fuser unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PWB (KP- 992). Replace the fuser unit (fuser PWB [KP- 997]). Replace the fuser unit (lower fuser thermistor). Check the continuity of the harness (2CK2719, 2CK2712). Check the insertion of connectors. |
| Error code: | 7001 |
| Description: | Toner motor error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB. |
| Remedy: | Toner container 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7002 |
| Description: | Toner motor C error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor C. Defective toner motor C. Defective engine PWB. |
| Remedy: | Toner container C 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Screw sensor C 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor C and Engine PWB (YC27) 3. Replace the screw sensor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7003 |
| Description: | Toner motor M error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor M. Defective toner motor M. Defective engine PWB. |
| Remedy: | Toner container M 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Screw sensor M 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor M and Engine PWB (YC27) 3. Replace the screw sensor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7004 |
| Description: | Toner motor Y error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor Y. Defective toner motor Y. Defective engine PWB. |
| Remedy: | Toner container Y 1. Check that the spiral screw of the toner container can be rotated by the hand. 1. Check for broken gears and replace if any. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Screw sensor Y 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor Y and Engine PWB (YC27) 3. Replace the screw sensor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7101 |
| Description: | Toner sensor error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7102 |
| Description: | Toner sensor C error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor C 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit C are not damaged and the spiral can rotate. 5. Replace the Developer unit C. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7103 |
| Description: | Toner sensor M error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor M 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit M are not damaged and the spiral can rotate. 5. Replace the Developer unit M. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7104 |
| Description: | Toner sensor Y error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor Y 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit Y are not damaged and the spiral can rotate. 5. Replace the Developer unit Y. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7301 |
| Description: | Toner hopper motor error During the Toner hopper motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective toner hopper sensor. Defective toner hopper motor. Defective engine PWB. |
| Remedy: | Toner hopper motor 1. If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner hopper motor and Front PWB (YC5) Front PWB (YC3) and Engine PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the toner hopper motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7700 ... 7710 |
| Description: | Offset drum sensor detection error • A pulse signal is not entered to ASIC (U7) on the engine controller PWB from the offset drum sensor. |
| Causes: | Defective drum PWB (KP-999). Defective engine controller PWB (KP-992). Defective harness (2BM2864, 2CK2714) between engine controller PWB (KP-992) and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the drum unit. Replace the engine controller PWB (KP- 992). Check the continuity of the harness (2BM2864, 2CK2714). Check the insertion of connectors. |
| Error code: | 8010 |
| Description: | Punch motor error 1 When the punch motor is driven, punch home position sensor does not turn on within 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch home position sensor. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch home position sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch home position sensor and Punch PWB (YC8) 4. Replace the Punch home position sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8020 |
| Description: | Punch motor error 2 Home position is not obtained in 3 s after home position is initialized or in standby. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8170 |
| Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8230 |
| Description: | DF staple motor error 1 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF staple sensor Replace the staple unit. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8290 |
| Description: | Sorter compatibility error • The engine controller PWB (KP-992) does not recognize compatibility of the SO-30 mailbox sorter. |
| Causes: | The ROM version of mailbox sorter S0-30 main board is not compatible for this printer. Defective mailbox sorter S0-30 main board. Defective engine controller PWB (KP-992). |
| Remedy: | Replace the ROM of mailbox sorter S0-30 main board for this printer. Replace the sorter SO-30 main board. See SO-30 mailbox sorter’s service manual. Replace the engine controller PWB (KP- 801). |
| Error code: | 8510 |
| Description: | MB conveying motor error 1 When initial operation, MB home position sensor does not turn on within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor. Defective MB main PWB. |
| Remedy: | MB conveying motor 1. If the transfer roller won’t rotate smoothly, repair its mechanism. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
| Error code: | 8900 |
| Description: | Document finisher backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective DF main PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F030 |
| Description: | Main PWB system error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F060 |
| Description: | Engine RAM error |
| Causes: | Defective engine PWB. |
| Remedy: | Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | F070 |
| Description: | Communication error between System-CPU and Engine-CPU |
| Causes: | Switching regulator • Replace the fuse (F210). • Replace the switching regulator. LGC board SYS board If the problem is not corrected with the replacement of the LGC board, reinstall the removed LGC board and replace the SYS board. IMG board If the problem is still not corrected with the replacement of the SYS board, reinstall the removed SYS board and replace the IMG board. |
| Remedy: | (1) Check if the connector CN104 on the SYS board and CN130, CN131, CN134 on the SYSIF board is disconnected. (2) Check if the connector CN10 on the SLG board is disconnected. (3) Check if the harness connecting the SYSIF board and SLG board is disconnected or open circuited. (4) Check if the harness connecting the SYSIF board and LGC board is disconnected or open circuited. (5) Check if the connection of the SYS board (CN104) and SYSIF board (CN130) is open circuited. (6) If the SYS board has been replaced, check if the jumper pin setting on the SYS board is correct. (The jumper pin should be inserted between pin 2 and 3 of CN103 and CN115.) (7) Check the version of the system ROM on the SYS board. (8) Check the version of the engine ROM version on the LGC board. (9) Check the version of the scanner ROM version on the SLG board. (10) Replace the SYS board. (11) Replace the SLG board. (12) Replace the LGC board. (13) Replace the SYSIF board. |
