Kyocera KM-4035
Рейтинг
Модули
PAPER FEED-IN SECTION I
Bypass feed unit
Bypass unit
PAPER FEED-IN SECTION II
OPTION II and TOOL
ELECTRICAL COMPONENTS
DRIVING, COOLING SECTION I
DRIVING, COOLING SECTION II
DEVELOPING SECTION
CASSETTE
OPTICAL SECTION
OPTION (ORIGINAL HOLDER)
PAPER FEED-IN SECTION III
FIXING SECTION
PAPER EXIT SECTIONCTION
CLEANING SECTION
Paper Conveying Section
FRAMES
OPERATION UNIT
OPTION I
Exterior Covers
LASER SCANNER UNIT
Детали OPTION I
| Деталь: | PRIMARY PAPER FEED ASSY |
| Парткод: | 2BL00050 |
| Деталь: | PLUG,QR/P15-8S-C(HIROSE) |
| Парткод: | J0463080 |
| Деталь: | UPPER HOUSING,PAPER FEED |
| Парткод: | 2AR07200 |
| Деталь: | LOWER HOUSING,PAPER FEED |
| Парткод: | 2AR07210 |
| Деталь: | PULLEYPAPER FEED |
| Парткод: | 2AR07220 |
| Цена: | 1 600 ₽ |
| Деталь: | PULLEYSEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | PULLEYLEADING FEED |
| Парткод: | 2AR07240 |
| Деталь: | SHAFT,PAPER FEED |
| Парткод: | 2AR07250 |
| Деталь: | SHAFT,SEPARATION |
| Парткод: | 2AR07260 |
| Деталь: | SHAFT,LEADING FEED |
| Парткод: | 2AR07270 |
| Деталь: | PLATE LEADING FEED |
| Парткод: | 2BL07900 |
| Деталь: | SUPPORT PLATE FEED |
| Парткод: | 2BL07910 |
| Деталь: | WEIGHT,LEADING FEED PULLEY |
| Парткод: | 2AR07300 |
| Деталь: | LEVER,SEPARATION PULLEY RELEASE |
| Парткод: | 2AR07310 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 2BL07990 |
| Деталь: | ACTUATOR,PAPER EMPTY |
| Парткод: | 2AR07640 |
| Деталь: | HOLDER,ACTUATOR |
| Парткод: | 2AR07650 |
| Деталь: | GUIDE FILM,SEPARATION PULLEY |
| Парткод: | 2AR07660 |
| Деталь: | REINFORCEMENT,PRIMARY PAPER FEED |
| Парткод: | 2AR07670 |
| Деталь: | STOPPER,SUPPORT PLATE |
| Парткод: | 2AR07690 |
| Деталь: | GROUND PLATE,PRIMARY PAPER FEED |
| Парткод: | 2AR07790 |
| Деталь: | GEAR 15 |
| Парткод: | 34922420 |
| Деталь: | BUSHING,6 REGISTRATION |
| Парткод: | 29806810 |
| Деталь: | TORQUE LIMITER,PAPER FEED |
| Парткод: | 33906070 |
| Деталь: | GEAR 16,PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | LOWER BUSHING,PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | SWITCH PI |
| Парткод: | 2DC27180 |
| Деталь: | WIRE,PRIMARY PAPER FEED UNIT |
| Парткод: | 2AR27430 |
| Деталь: | PARTS,BYPASS FEED UNIT |
| Парткод: | 2BL93390 |
| Деталь: | MOUNT RAIL |
| Парткод: | 2BL06570 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BL06590 |
| Деталь: | RAIL BYPASS |
| Парткод: | 2BL06580 |
| Деталь: | BASE BYPASSFEED(1) |
| Парткод: | 2BL06500 |
| Деталь: | GROUNDPLATE BYPASS |
| Парткод: | 2BL06790 |
| Деталь: | ACTUATOR BYPASSFEED |
| Парткод: | 2BL06730 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL06800 |
| Деталь: | SPRING BYPASSFEED |
| Парткод: | 2BL06780 |
| Деталь: | SHAFT BYPASSFEED |
| Парткод: | 2BL06740 |
| Деталь: | RIGHT PULLEY,FEED |
| Парткод: | 33906660 |
| Деталь: | ROLLER2BYPASSFEED |
| Парткод: | 2BL06540 |
| Деталь: | ROLLER4BYPASSFEED |
| Парткод: | 2BL06560 |
| Деталь: | UPPERGUIDE BYPASS |
| Парткод: | 2BL06520 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | DIAL BYPASSFEED |
| Парткод: | 2BL06830 |
| Деталь: | PULLEY25 BYPASSFEED |
| Парткод: | 2BL06820 |
| Деталь: | BELT BYPASSFEED |
| Парткод: | 2BL06810 |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | FRONT LABEL BYPASS |
| Парткод: | 2BL05020 |
| Деталь: | UPPER LABEL BYPASS |
| Парткод: | 2BL05030 |
| Деталь: | BYPASS UNIT(C) |
| Парткод: | 2FG68010 |
| Деталь: | BYPASS UNIT(I) |
| Парткод: | 2FG68020 |
| Деталь: | FRONT CURSOR BYPASS |
| Парткод: | 2BL06660 |
| Деталь: | REAR CURSOR BYPASS |
| Парткод: | 2BL06670 |
| Деталь: | STAY LIFTPLATE |
| Парткод: | 2BL06650 |
| Деталь: | RACK,CASSETTE |
| Парткод: | 33907100 |
| Деталь: | GEAR 18,IDLE DEVELOPING |
| Парткод: | 65914120 |
| Деталь: | MOUNT,BYPASS PCB |
| Парткод: | 3A206461 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | FRICTION PLATE,BYPASS LEADING FEED |
| Парткод: | 34806490 |
| Деталь: | SWITCH,BYPASS SIZE DETECTION |
| Парткод: | 33906990 |
| Деталь: | WIRE BYPASS TRAY |
| Парткод: | 2BL27210 |
| Деталь: | TABLE BYPASS |
| Парткод: | 2BL06610 |
| Деталь: | COVER BYPASSTRAY |
| Парткод: | 2BL06600 |
| Деталь: | LABEL BYPASSSIZE(C) |
| Парткод: | 2BL05010 |
| Деталь: | LABEL BYPASSSIZE(I) |
| Парткод: | 2BL05060 |
| Деталь: | JOINT,BYPASS PICKUP |
| Парткод: | 3A206130 |
| Деталь: | GEAR 30, FD EJECT IDLE |
| Парткод: | 72321350 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | MOUNT,BYPASS PE SWITCH |
| Парткод: | 3A206210 |
| Деталь: | SWITCH PI |
| Парткод: | 2BL27450 |
| Деталь: | PULLEY,LEADING FEED |
| Парткод: | 2AR07240 |
| Деталь: | SHAFT BYPASSCAM |
| Парткод: | 2BL06760 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | ARM,BYPASS PE |
| Парткод: | 3A206100 |
| Деталь: | CAM BYPASS |
| Парткод: | 2BL06680 |
| Деталь: | SHAFT BYPASS |
| Парткод: | 2BL06770 |
| Деталь: | GEAR,TONER ROLLER |
| Парткод: | 45729416 |
| Деталь: | FILM BYPASS |
| Парткод: | 2BL06880 |
| Деталь: | UPPER PULLEY,BYPASS |
| Парткод: | 61706770 |
| Цена: | 1 900 ₽ |
| Деталь: | BASE BYPASSUNIT(1) |
| Парткод: | 2BL06510 |
| Деталь: | MOUNT BYPASSDRIVE |
| Парткод: | 2BL06690 |
| Деталь: | SHAFT RETARD |
| Парткод: | 2BL06750 |
| Деталь: | TORQUE LIMITER,BYPASS |
| Парткод: | 33906430 |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | HOLDER,RETARD |
| Парткод: | 3A206170 |
| Деталь: | GEAR,16 BYPASS PULLEY |
| Парткод: | 66006810 |
| Деталь: | SPRING RETARD |
| Парткод: | 2BL06860 |
| Деталь: | PIN,CASSETTE WORK PLATE |
| Парткод: | 66007310 |
| Деталь: | SPRING BYPASS |
| Парткод: | 2BL07860 |
| Деталь: | WIRE BYPASS UNIT |
| Парткод: | 2BL27150 |
| Деталь: | COVER BYPASSUNIT |
| Парткод: | 2BL06530 |
| Деталь: | CLUTCH B,PAPER FEED |
| Парткод: | 2AV27451 |
| Деталь: | JOINT RETARD |
| Парткод: | 2BL06850 |
| Деталь: | LABEL RETARD |
| Парткод: | 2BL05040 |
| Деталь: | CLUTCH FEED |
| Парткод: | 2BL27500 |
| Деталь: | SPRING JOINTRETARD |
| Парткод: | 2BL06870 |
| Деталь: | GEAR 16,PAPER FEED |
| Парткод: | 33906160 |
| Деталь: | GEAR 55/15 |
| Парткод: | 2BL06720 |
| Деталь: | TERMINAL,PAPER SIZE PCB |
| Парткод: | 33907110 |
| Деталь: | MINIATURE CLAMPUAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | EDGING,EDS-2 |
| Парткод: | M2104210 |
| Деталь: | STOPPER GEAR 8-25 |
| Парткод: | 2BL06990 |
| Деталь: | LIFTPLATE BYPASS |
| Парткод: | 2BL06641 |
| Деталь: | MINI CLAMP,UAMS-02WL-0(KITAGAWA) |
| Парткод: | M2105210 |
| Деталь: | PLATE BYPASS HOLD |
| Парткод: | 2BL06890 |
| Деталь: | LABEL,CAUTION GEAR |
| Парткод: | 3A205010 |
| Деталь: | LABEL BYPASS JAM R |
| Парткод: | 2BL05100 |
| Деталь: | PIN COVER |
| Парткод: | 2BL04410 |
| Деталь: | PARTS/VERTICAL FEED ASSY,SP |
| Парткод: | 2FG93080 |
| Деталь: | EARTH VERTICAL FEED |
| Парткод: | 2BL06220 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | ROLLER B FEED |
| Парткод: | 2BL06080 |
| Деталь: | ROLLERCFEED |
| Парткод: | 2BL06090 |
| Деталь: | CLUTCH FEED |
| Парткод: | 2BL27500 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GEAR Z42 FEED |
| Парткод: | 2BL06170 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | MOUNT FEED DRIVE A |
| Парткод: | 2FG06020 |
| Деталь: | GEAR Z21-Z36 FEED |
| Парткод: | 2FG06040 |
| Деталь: | GEAR 30,IDLE |
| Парткод: | 36222250 |
| Деталь: | GEAR 25 |
| Парткод: | 2AL06110 |
| Деталь: | GEAR Z25 JOINT |
| Парткод: | 2BL06380 |
| Цена: | 370 ₽ |
| Деталь: | MOUNT C FEED DRIVE |
| Парткод: | 2BL06130 |
| Деталь: | GEAR Z28-P18 FEED |
| Парткод: | 2BL06180 |
| Деталь: | BELT CONVEYING |
| Парткод: | 2BL06320 |
| Деталь: | WIRE CONVEYING |
| Парткод: | 2BL27190 |
| Деталь: | HOLDER FEED SWITCH |
| Парткод: | 2BL06450 |
| Деталь: | SWITCH CONVEYING |
| Парткод: | 2BL27410 |
| Деталь: | GUIDE VERTICAL FEED |
| Парткод: | 2BL06110 |
| Деталь: | GUIDE B FEED |
| Парткод: | 2BL06330 |
| Деталь: | LOCK COVER RIGHT |
| Парткод: | 2BL06490 |
| Деталь: | SPRING LEFT COVER |
| Парткод: | 2BL06460 |
| Деталь: | EARTH PUSH SWITCH |
| Парткод: | 2BL06940 |
| Деталь: | FRAME VERTICAL FEED A |
| Парткод: | 2FG06010 |
| Деталь: | MOUNT FEED DRIVE B |
| Парткод: | 2FG06030 |
| Деталь: | JOINT FEED DRIVE |
| Парткод: | 2FG06050 |
| Деталь: | SHAFT FEED JOINT |
| Парткод: | 2FG06060 |
| Деталь: | SPRING FEED JOINT |
| Парткод: | 2FG06070 |
| Деталь: | COLLAR FEED JOINT |
| Парткод: | 2FG06120 |
| Деталь: | SPRING GUIDE FEED |
| Парткод: | 2FG06130 |
| Деталь: | CASE,BU03P-TR-PC-H(JST) |
| Парткод: | J5016030 |
| Деталь: | WIRE SADDLE,YMC-10-0(KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | FRONT RAIL FEED |
| Парткод: | 2BL06051 |
| Деталь: | REAR RAIL FEED |
| Парткод: | 2BL06061 |
| Деталь: | SHAFT LEFT COVER M |
| Парткод: | 2BL04520 |
| Деталь: | SPRING CONV OPEN |
| Парткод: | 2BL16230 |
| Деталь: | DUMPER LEFT COVER |
| Парткод: | 2BL06950 |
| Деталь: | STOPPER 7,CARTRIDGE |
| Парткод: | 33973300 |
| Деталь: | RIGHT GUIDE TRANSFER |
| Парткод: | 2BL17160 |
| Деталь: | GUIDE ROLLER FRONT |
| Парткод: | 2BL06310 |
| Деталь: | GUIDE ROLLER REAR |
| Парткод: | 2BL06350 |
| Деталь: | CAM DLP |
| Парткод: | 2BL14240 |
| Деталь: | SPRING CAM |
| Парткод: | 2BL14410 |
| Деталь: | MOUNT CAM |
| Парткод: | 2BL14140 |
| Деталь: | SHAFT CAM |
| Парткод: | 2BL14230 |
| Деталь: | BUSH POM |
| Парткод: | 2BM17920 |
| Деталь: | GEAR 18 |
| Парткод: | 2BL14250 |
| Деталь: | RIGHT ROLLER REGIST |
| Парткод: | 2BL06270 |
| Деталь: | POSITIONING PLATE,LSU |
| Парткод: | 2AR02250 |
| Деталь: | PARTS,MIDDLE FEED ASSY |
| Парткод: | 2FG93060 |
| Деталь: | GROUND PLATE A FEED |
| Парткод: | 2BL06230 |
| Деталь: | WIRE FEED 1 |
| Парткод: | 2BL27240 |
| Деталь: | GUIDE A FEED |
| Парткод: | 2BL06020 |
| Деталь: | SHAFT FEED A |
| Парткод: | 2BL06920 |
| Деталь: | FILM REGIST F |
| Парткод: | 2BL06480 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL06930 |
| Деталь: | FILM REGIST FF |
| Парткод: | 2BL06970 |
| Деталь: | GEAR Z42 BYPASS |
| Парткод: | 2BL06360 |
| Деталь: | MOUNT BYPASS FEED |
| Парткод: | 2FG06160 |
| Деталь: | GEAR Z25 FEED |
| Парткод: | 2BL06190 |
| Деталь: | GEAR Z35-15 FEED |
| Парткод: | 2BL06160 |
| Деталь: | GEAR Z28 FEED |
| Парткод: | 2BL06150 |
| Деталь: | MOUNT MID FEED DRIVE |
| Парткод: | 2FG06150 |
| Деталь: | HOUSING FEED A |
| Парткод: | 2FG06080 |
| Деталь: | CLUTCH,REGISTRATION |
| Парткод: | 2BL27730 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GROUND PLATE GUIDE A |
| Парткод: | 2FG06170 |
| Деталь: | GUIDE MIDDLE FEED |
| Парткод: | 2FG06090 |
| Деталь: | SHAFT MIDDLE FEED |
| Парткод: | 2FG06100 |
| Деталь: | PULLEY MIDDLE FEED |
| Парткод: | 2FG06110 |
| Деталь: | GEAR 18 |
| Парткод: | 36722860 |
| Деталь: | FRONT GUIDE REGIST |
| Парткод: | 2BL06260 |
| Деталь: | MOUNT REGIST SWITCH |
| Парткод: | 2BL06440 |
| Деталь: | SWITCH REGISTRATION |
| Парткод: | 2FG27110 |
| Деталь: | WIRE REGISTRATION |
| Парткод: | 2BL27170 |
| Деталь: | REGIST CLEANER ASSY |
| Парткод: | 2BL68291 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 2BL06430 |
| Деталь: | SET PARTS KEYCOUNTER NEW COLOR |
| Парткод: | 2A369703 |
| Деталь: | SOCKET ASSY,KEY COUNTER |
| Парткод: | 41529210 |
| Деталь: | PLUG EL 4P.ELP-04V |
| Парткод: | J0220040 |
| Деталь: | SOCKET,KEY COUNTER |
| Парткод: | 41525016 |
| Деталь: | RETAINER,KEY COUNTER COVER |
| Парткод: | 66060022 |
| Деталь: | RETAINER,KEY COUNTER |
| Парткод: | 66060030 |
| Деталь: | MOUNT,KEY COUNTER |
| Парткод: | 66060040 |
| Деталь: | COUNTER-SUNK HEAD SCREW BFHM3X6 (BLACK) |
| Парткод: | B2303060 |
| Деталь: | BINDING SCREW BVM4X30 (BLACK) |
| Парткод: | B1304300 |
| Деталь: | TRIPLE SCREW M4X6 (BLACK) |
| Парткод: | B4304060 |
| Деталь: | TRIPLE SCREW M4X10 (BLACK) |
| Парткод: | B4304100 |
| Деталь: | BINDING SCREW BVM3X8 (BLACK) |
| Парткод: | B1303080 |
| Деталь: | TRIPLE SCREW M4X6(CHROMIUM) |
| Парткод: | B4104060 |
| Деталь: | TRIPLE SCREW M4X20(BLACK) |
| Парткод: | B4304200 |
| Деталь: | NUT BNM3 (BLACK) |
| Парткод: | C2303000 |
| Деталь: | COVER,KEY COUNTER |
| Парткод: | 2A360010 |
| Деталь: | KEY COUNTER |
| Парткод: | 82142540 |
| Деталь: | STOPPER WIRE ASSY SP |
| Парткод: | 35968110 |
| Деталь: | SPECIAL TOOL,MIRROR FRAME RETAINING |
| Парткод: | 2AV68080 |
| Деталь: | GRID CLEANER 3 ASSY |
| Парткод: | 4AK85050 |
| Деталь: | PARTS,DISPOSAL TANK,TB700 |
| Парткод: | 2BL93130 |
| Деталь: | HEATER,CASSETTE(120) |
| Парткод: | 34860030 |
| Деталь: | HEATER,CASSETTE (240) |
| Парткод: | 33960020 |
| Деталь: | BINDING BAND SG-130 |
| Парткод: | M2107120 |
| Деталь: | BINDING SCREW BVM4X6 (BLACK) |
| Парткод: | B1304060 |
| Деталь: | MOUNT PCB |
| Парткод: | 2BJ26010 |
| Деталь: | ENGINE PCB ASSY |
| Парткод: | 2FG01010 |
| Деталь: | FERRITE CORE |
| Парткод: | 63827080 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | WIRE BYPASS FEED PI |
| Парткод: | 2BL27290 |
| Деталь: | RECEPTACLE,QR/P15-8S-C(02)(HIROSE) |
| Парткод: | J0464080 |
| Деталь: | RETAINING PIN,DRAWER |
| Парткод: | 33927450 |
| Деталь: | MOUNT DRUM DRAWER |
| Парткод: | 2BL26200 |
| Деталь: | RECEPTACLE,9715S-10A(IRS) |
| Парткод: | J7340100 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | M2109010 |
| Деталь: | WIRE SADDLE,YMC-10-0(KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | WIRE SADDLE,RLWS-2020T V0(KITAGAWA) |
| Парткод: | M2109400 |
| Деталь: | SPACER,KGLS-4S |
| Парткод: | M2108120 |
| Деталь: | WIRE PAPER FEED(C) |
| Парткод: | 2BJ27100 |
| Деталь: | CASSETTE SWITCH ASSY |
| Парткод: | 2AR00150 |
| Деталь: | MOUNT,CASSETTE SWITCH |
| Парткод: | 2AR07170 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | MOUNT POWER PCB |
| Парткод: | 2FG26010 |
| Деталь: | POWER SOURCE PCB(100) |
| Парткод: | 2FG28020 |
| Деталь: | POWER SOURCE PCB(200) |
| Парткод: | 2FG28030 |
| Деталь: | WIRE FILTER PCB |
| Парткод: | 2FG27370 |
| Деталь: | MOUNT OPTION I/F (E) |
| Парткод: | 2BJ26100 |
| Деталь: | WIRE SADDLE,WS-2WS |
| Парткод: | M2109020 |
| Деталь: | CASE,54082-1215(MOLEX) |
| Парткод: | J0326120 |
| Деталь: | WIRE FINISHER GND(C) |
| Парткод: | 2BJ27220 |
| Деталь: | WIRE FINISHER FG |
| Парткод: | 2BJ27230 |
| Деталь: | WIRE OPTION(C) |
| Парткод: | 2FG27320 |
| Деталь: | MOUNT,DECK CONNECTOR |
| Парткод: | 2AR26340 |
| Деталь: | SPACER,KGPS-6RF(KITAGAWA) |
| Парткод: | M2108670 |
| Деталь: | PCB DIMM64 |
| Парткод: | 2FG28070 |
| Деталь: | EDGING,EDS-25L(KITAGAWA) |
| Парткод: | M2104280 |
| Деталь: | MOUNT FIXING DRAWER |
| Парткод: | 2BL26290 |
| Деталь: | WIRE DRAWER |
| Парткод: | 2BL27030 |
| Деталь: | WIRE PRIMARY(C) |
| Парткод: | 2FG27330 |
| Деталь: | PIN TERMINAL |
| Парткод: | 2BL26060 |
| Деталь: | SPRING TERMINAL |
| Парткод: | 2BL26070 |
| Деталь: | SPRING TERMINAL T |
| Парткод: | 2BL26270 |
| Деталь: | CASE HIGH VOLTAGE |
| Парткод: | 2BL26050 |
| Деталь: | GROUND PLATE HV |
| Парткод: | 2BL26080 |
| Деталь: | HIGH VOLTAGE PCB |
| Парткод: | 2BL28051 |
| Деталь: | WIRE HIGH VOLTAGE(C) |
| Парткод: | 2BJ27130 |
| Деталь: | WIRE MOTOR(C) |
| Парткод: | 2FG27310 |
| Деталь: | WIRE FRONT(C) |
| Парткод: | 2BJ27090 |
| Деталь: | EDGING,EDS-2 |
| Парткод: | M2104210 |
| Деталь: | LEFT MOUNT I/L |
| Парткод: | 2BL26110 |
| Деталь: | SWITCH INTERLOCK |
| Парткод: | 2FG27120 |
| Деталь: | SWITCH,INTERLOCK |
| Парткод: | 2AR27040 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | LEFT WORK PLATE I/L |
| Парткод: | 2BL26120 |
| Деталь: | SWITCH,MAIN |
| Парткод: | 2AV27290 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 2BM27890 |
| Деталь: | FRONT MOUNT COVER |
| Парткод: | 2BL04060 |
| Деталь: | INNER LEFT COVER |
| Парткод: | 2BL04080 |
| Деталь: | TONER SW ASSY |
| Парткод: | 2BL01160 |
| Деталь: | CASE,BU05P-TR-PC-H(JST) |
| Парткод: | J5016050 |
| Деталь: | WIRE TONER DISPOSAL |
| Парткод: | 2BL27250 |
| Деталь: | CASE,BU12P-TR-PC-H(JST) |
| Парткод: | J5016120 |
| Деталь: | CASE,BU13P-TR-PC-H(JST) |
| Парткод: | J5016130 |
| Деталь: | GROUND PLATE INNER L |
| Парткод: | 2BL04450 |
| Деталь: | BINDING BAND SG-130 |
| Парткод: | M2107120 |
| Деталь: | FAN MOTOR 3 |
| Парткод: | 2FG27140 |
| Деталь: | SHIELD PCB |
| Парткод: | 2FG26040 |
| Деталь: | FILM SHIELD |
| Парткод: | 2FG26080 |
| Деталь: | SPACER WIRE |
| Парткод: | 2BL04460 |
| Деталь: | SHAFT I/L |
| Парткод: | 2BL26280 |
| Деталь: | GASKET MULTIPORT B |
| Парткод: | 2FG27540 |
| Деталь: | GASKET SHIELD |
| Парткод: | 2FG27550 |
| Деталь: | LID HDD |
| Парткод: | 2FG26030 |
| Деталь: | LID MODULAR |
| Парткод: | 2BJ26120 |
| Деталь: | LID NETWORKSCANNER |
| Парткод: | 2BJ26130 |
| Деталь: | LID PRINTER BOARD |
| Парткод: | 2FG26070 |
| Деталь: | SHIELD SUBWIRE |
| Парткод: | 2BJ26210 |
| Деталь: | UPPER SHIELD PCB |
| Парткод: | 2FG26050 |
| Деталь: | RAIL PRINTER PCB |
| Парткод: | 2FG26060 |
| Деталь: | LID MMD |
| Парткод: | 2BJ26150 |
| Деталь: | CLAMP,EMT-3N(TAKEUCHI) |
| Парткод: | M7005010 |
| Деталь: | GASKET MULTIPORT A |
| Парткод: | 2FG27530 |
| Деталь: | MOUNT INLET CORD 230 |
| Парткод: | 2BL26250 |
| Деталь: | INLET ASSY |
| Парткод: | 2FG01090 |
| Деталь: | MOUNT FILTER PCB |
| Парткод: | 2FG26090 |
| Деталь: | NOISE FILTER PCB 100 |
| Парткод: | 2FG28120 |
| Деталь: | NOISE FILTER PCB 200 |
| Парткод: | 2FG28130 |
| Деталь: | SPACER,KGLS-5RT(KITAGAWA) |
| Парткод: | M2108920 |
| Деталь: | WIRE SADDLE,YMC-15-0(KITAGAWA) |
| Парткод: | M2109350 |
| Деталь: | CLAMP,CKN-07(KITAGAWA) |
| Парткод: | M2105910 |
| Деталь: | FILM SUB PS CN |
| Парткод: | 2BJ26230 |
| Деталь: | FILM POWER SOURCE |
| Парткод: | 2BJ26220 |
| Деталь: | POWER CORD 110 |
| Парткод: | 65027600 |
| Деталь: | POWER CORD(120) |
| Парткод: | 19527400 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | POWER CODE AS(240) |
| Парткод: | 29927231 |
| Деталь: | CORE 15-26X13 |
| Парткод: | 2AV27440 |
| Деталь: | GASKET LID PRINTER |
| Парткод: | 2FG27520 |
| Деталь: | FUSE,237010(LITTEL) |
| Парткод: | M1660010 |
| Деталь: | FUSE,215005(LITTEL) |
| Парткод: | M1655040 |
| Деталь: | FUSE,21502.5(LITTEL-FUSE) |
| Парткод: | M1652040 |
| Деталь: | FUSE,215008(LITTEL-FUSE) |
| Парткод: | M1658030 |
| Деталь: | FUSE,21506.3(LITTEL-FUSE) |
| Парткод: | M1656050 |
| Деталь: | PLATE DRIVE CONT.B |
| Парткод: | 2BL22450 |
| Деталь: | CLUTCH CONTAINER |
| Парткод: | 2BL22520 |
| Деталь: | SHAFT DRIVE CONT |
| Парткод: | 2BL22460 |
| Деталь: | COUPLING C,CONT. |
| Парткод: | 2BJ22020 |
| Деталь: | COUPLING CONTAINER B |
| Парткод: | 2BJ22010 |
| Деталь: | SPRING DRIVE CONT. |
| Парткод: | 2BL22510 |
| Деталь: | BUSH DRIVE CONT 8 |
| Парткод: | 2BL22570 |
| Деталь: | GEAR Z24S-P40 |
| Парткод: | 2BL22480 |
| Деталь: | PULLEY CONT. DRIVE |
| Парткод: | 2BL22560 |
| Деталь: | BELT DRIVE CONTAINER |
| Парткод: | 2BL22590 |
| Деталь: | PLATE DRIVE CONT.A |
| Парткод: | 2BL22440 |
| Деталь: | GEAR Z40S-Z25S |
| Парткод: | 2BL22490 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | SOLENOID TONER |
| Парткод: | 2BL27510 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | GEAR Z41S-Z24S-P30 |
| Парткод: | 2BL22330 |
| Деталь: | CLUTCH FEED |
| Парткод: | 2BL27500 |
| Деталь: | BELT DRIVE FEED |
| Парткод: | 2BL22350 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GEAR M FEED Z25 |
| Парткод: | 2BL22740 |
| Деталь: | GEAR Z41S-P15 |
| Парткод: | 2BL22530 |
| Деталь: | LIFT MOTOR |
| Парткод: | 2BL27581 |
| Деталь: | BRACKET CLUTCH FEED |
| Парткод: | 2FG22090 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | GEAR Z60S-P20 |
| Парткод: | 2BL22540 |
| Деталь: | PRIMARY PAPER FEED BUSHING ASSY |
| Парткод: | 2AR00170 |
| Деталь: | GEAR Z41S-P18 |
| Парткод: | 2BL22420 |
| Деталь: | BELT DRIVE MPF |
| Парткод: | 2BL22400 |
| Деталь: | PLATE DRIVE MPF A |
| Парткод: | 2BL22370 |
| Деталь: | GEAR Z40S-Z32S |
| Парткод: | 2BL22550 |
| Цена: | 550 ₽ |
| Деталь: | PLATE DRIVE MPF B |
| Парткод: | 2BL22380 |
| Деталь: | PLATE DRIVE FEED A |
| Парткод: | 2FG22070 |
| Деталь: | FEED MOTOR |
| Парткод: | 2FG27020 |
| Деталь: | GEAR Z76H-Z35S |
| Парткод: | 2BL22320 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE SADDLE,YMC-10-0(KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | M2109010 |
| Деталь: | SPACER,KGPS-3S |
| Парткод: | M2108080 |
| Деталь: | WIRE CONT SW |
| Парткод: | 2BL27180 |
| Деталь: | PLATE TENSION A |
| Парткод: | 2BL22810 |
| Деталь: | PIN,DEV.UNIT HANDLE |
| Парткод: | 72114320 |
| Деталь: | PULLEY TENSION |
| Парткод: | 2BL22830 |
| Деталь: | SPRING PULLEY |
| Парткод: | 2BL22820 |
| Деталь: | PULLEY MPF DRIVE |
| Парткод: | 2BL22390 |
| Деталь: | PLATE DRIVE FEED B |
| Парткод: | 2FG22080 |
| Деталь: | PARTS,MOTORASSY,DR |
| Парткод: | 2FG93070 |
| Деталь: | MOTOR MAIN |
| Парткод: | 2BL27540 |
| Деталь: | GUIDE DLP |
| Парткод: | 2BL22140 |
| Деталь: | SPRING JOINT FUSER |
| Парткод: | 2BL22240 |
| Деталь: | GEAR Z36S-Z31H |
| Парткод: | 2BL22220 |
| Деталь: | GEAR Z50H |
| Парткод: | 2BL22190 |
| Деталь: | GEAR Z37H-Z28H |
| Парткод: | 2BL22180 |
| Деталь: | GEAR Z34H |
| Парткод: | 2BL22230 |
| Деталь: | GEAR Z59H-Z44S |
| Парткод: | 2FG22030 |
| Деталь: | GEAR Z76H-Z35H |
| Парткод: | 2BL22710 |
| Деталь: | GEAR Z37S |
| Парткод: | 2BL22770 |
| Деталь: | GEAR Z22S |
| Парткод: | 2FG22040 |
| Деталь: | GEAR DRUM Z76H-Z30H |
| Парткод: | 2BL22160 |
| Деталь: | GEAR JOINT Z32S |
| Парткод: | 2BL22210 |
| Деталь: | PLATE DRIVE FRONT |
| Парткод: | 2FG22010 |
| Деталь: | PLATE GUIDE DRUM |
| Парткод: | 2BL22170 |
| Деталь: | SHAFT DRIVE DRUM FW |
| Парткод: | 2BL22840 |
| Деталь: | GEAR DRUM Z70H |
| Парткод: | 2BL22050 |
| Деталь: | BEARING 6900ZZNR |
| Парткод: | G3169000 |
| Деталь: | PLATE DRIVE REAR |
| Парткод: | 2FG22020 |
| Деталь: | MOTOR EJECT |
| Парткод: | 2BL27560 |
| Деталь: | PLATE DRIVE EXIT A |
| Парткод: | 2FG22050 |
| Деталь: | GEAR Z47S-Z28S |
| Парткод: | 2BL22800 |
| Деталь: | GEAR EXIT Z30S |
| Парткод: | 2BL22630 |
| Деталь: | CLUTCH,REGISTRATION |
| Парткод: | 2BL27730 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | DUCT DRUM |
| Парткод: | 2BL23020 |
| Деталь: | COVER DUCT DRUM |
| Парткод: | 2BL23120 |
| Деталь: | DUCT DLP |
| Парткод: | 2BL23030 |
| Деталь: | FAN MOTOR 1 |
| Парткод: | 2FG27130 |
| Деталь: | LID DLP DUCT |
| Парткод: | 2BL23040 |
| Деталь: | RETAINER FLYWHEEL |
| Парткод: | 2BL22850 |
| Деталь: | FLYWHEEL 190 |
| Парткод: | 2BL22860 |
| Деталь: | WEIGHT 190 |
| Парткод: | 2BL22870 |
| Деталь: | MOUNT BASE TERMINAL |
| Парткод: | 2BL26150 |
| Деталь: | PLATE TRANSFER A |
| Парткод: | 2BL26160 |
| Деталь: | PLATE SEPARATION A |
| Парткод: | 2BL26170 |
| Деталь: | EMPTY SW ASSY |
| Парткод: | 2BL01170 |
| Деталь: | DUCT MAIN A |
| Парткод: | 2BL23050 |
| Деталь: | DUCT MAIN B |
| Парткод: | 2BL23060 |
| Деталь: | FAN MOTOR 2 |
| Парткод: | 2FG27060 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | M2109010 |
| Деталь: | WIRE CONTAINER |
| Парткод: | 2BL27120 |
| Деталь: | RAIL DRUM R |
| Парткод: | 2BL02220 |
| Деталь: | WIRE SADDLE,YMC-10-0(KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | PLATE DRIVE EXIT B |
| Парткод: | 2FG22060 |
| Деталь: | MOUNT REAR FAN |
| Парткод: | 2BL23070 |
| Деталь: | FILM COOLING |
| Парткод: | 2BL23100 |
| Деталь: | FILM BKT CLUTCH |
| Парткод: | 2BL22880 |
| Деталь: | BRACKET CLUTCH |
| Парткод: | 2BL22150 |
| Деталь: | BUSHING, CUTTER |
| Парткод: | 49021301 |
| Деталь: | MOUNT FLYWHEEL |
| Парткод: | 2BL22890 |
| Деталь: | PARTS,DEVELOPER ASSY |
| Парткод: | 2BJ93010 |
| Деталь: | FRONT ARM RAIL |
| Парткод: | 2BL14180 |
| Деталь: | REAR ARM RAIL |
| Парткод: | 2BL14190 |
| Деталь: | RAIL DLP |
| Парткод: | 2BL14200 |
| Деталь: | LEVER DLP |
| Парткод: | 2BL14210 |
| Деталь: | PIN LEVER DLP |
| Парткод: | 2BL14220 |
| Деталь: | GROUND PLATE RAIL |
| Парткод: | 2BL14350 |
| Деталь: | SEAL WIRE |
| Парткод: | 2BL14480 |
| Деталь: | STUD SCREW S |
| Парткод: | 2BL14660 |
| Деталь: | PIN,JAM REMOVEMENT DIAL |
| Парткод: | 36006140 |
| Деталь: | RECEPTACLE,9715S-10A(IRS) |
| Парткод: | J7340100 |
| Деталь: | CASSETTE (A4) UNIT |
| Парткод: | 2FG68031 |
| Деталь: | CASSETTE (LTR) UNIT |
| Парткод: | 2FG68041 |
| Деталь: | PLUG,QR/P15-8S-C(HIROSE) |
| Парткод: | J0463080 |
| Деталь: | LABEL,CASSETTE OPERATION |
| Парткод: | 2AR05150 |
| Деталь: | LABEL,PAPER UPPER LIMIT |
| Парткод: | 2AR05200 |
| Деталь: | BASE,CASSETTE |
| Парткод: | 2AR07020 |
| Деталь: | WORK PLATE,CASSETTE BASE |
| Парткод: | 2AR07030 |
| Деталь: | SHAFT,WORK PLATE |
| Парткод: | 2AR07040 |
| Деталь: | RAIL A,CURSOR |
| Парткод: | 2AR07051 |
| Деталь: | CURSOR A,CASSETTE |
| Парткод: | 2AR07060 |
| Деталь: | CURSOR B,CASSETTE |
| Парткод: | 2AR07071 |
| Деталь: | CURSOR C,CASSETTE |
| Парткод: | 2AR07080 |
| Деталь: | RAIL C,CURSOR |
| Парткод: | 2AR07091 |
| Деталь: | FRONT GUIDE C,CURSOR |
| Парткод: | 2AR07100 |
| Деталь: | REAR GUIDE C,CURSOR |
| Парткод: | 2AR07110 |
| Деталь: | LID A,CURSOR |
| Парткод: | 2AR07120 |
| Деталь: | COVER CASSETTE |
| Парткод: | 2BL04140 |
| Деталь: | GROUND PLATE,CASSETTE |
| Парткод: | 2AR07150 |
| Деталь: | MOUNT,CASSETTE STOPPER |
| Парткод: | 2AR07160 |
| Деталь: | RETAINER M4 |
| Парткод: | 2AR07180 |
| Деталь: | SHAFT,CASSETTE PULLEY |
| Парткод: | 2AR07190 |
| Деталь: | LEVER A,CURSOR |
| Парткод: | 2AR07340 |
| Деталь: | STOPPER,TRAILING EDGE DETECTION |
| Парткод: | 2AR07610 |
| Деталь: | PROTECTING PLATE,CASSETTE WIRE |
| Парткод: | 2AR07620 |
| Деталь: | LID,TRAILING EDGE DETECTION PLATE |
| Парткод: | 2AR07630 |
| Деталь: | WIRE,CASSETTE UNIT |
| Парткод: | 2AR27220 |
| Деталь: | RACK,CASSETTE |
| Парткод: | 33907100 |
| Деталь: | DETECTION PLATE,PAPER SIZE |
| Парткод: | 33907170 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | SIZE DETECTION ASSY |
| Парткод: | 2FG01020 |
| Деталь: | PULLEY,CASSETTE |
| Парткод: | 34907150 |
| Деталь: | CUSHION,CASSETTE R |
| Парткод: | 60907170 |
| Деталь: | GEAR 18,IDLE DEVELOPING |
| Парткод: | 65914120 |
| Деталь: | SPRING,CURSOR C |
| Парткод: | 66007120 |
| Деталь: | SPRING,PAD |
| Парткод: | 66106080 |
| Деталь: | PAD,CASSETTE |
| Парткод: | 66107100 |
| Деталь: | CASSETTE STOPPER |
| Парткод: | 77906210 |
| Деталь: | TERMINAL,PAPER SIZE PCB |
| Парткод: | 33907110 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 2BL04160 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | PLATE NUMBER 2 |
| Парткод: | 2BL04370 |
| Деталь: | PLATE SIZE C |
| Парткод: | 2BL06470 |
| Деталь: | PLATE SIZE IN |
| Парткод: | 2BL06910 |
| Деталь: | MOUNT CUSHION |
| Парткод: | 2BL06980 |
| Деталь: | LABEL CASSETTE SIZE |
| Парткод: | 2BL05260 |
| Деталь: | STOPPER PAPER SP |
| Парткод: | 2BJ68190 |
| Деталь: | CCD DRIVE PCB ASSY |
| Парткод: | 2FG01040 |
| Деталь: | GUIDE FFC1 |
| Парткод: | 2AV12080 |
| Деталь: | MIRROR FRAME A |
| Парткод: | 2AV12091 |
| Деталь: | LAMPSCANNER |
| Парткод: | 2AV12100 |
| Деталь: | REFLECTOR,SCANNER |
| Парткод: | 2AV12110 |
| Деталь: | LIGHT SHIELD,PI |
| Парткод: | 2AV12121 |
| Деталь: | MIRROR FRAME B |
| Парткод: | 2AV12130 |
| Деталь: | ADJUSTING PLATE B,MIRROR FRAME |
| Парткод: | 2AV12140 |
| Деталь: | MIRROR A |
| Парткод: | 2AV12150 |
| Деталь: | MIRROR B |
| Парткод: | 2AV12160 |
| Деталь: | MOUNT,SCANNER PI |
| Парткод: | 2AV12170 |
| Деталь: | PULLY,SCANNER |
| Парткод: | 2AV12180 |
| Деталь: | FRONT WIRE,SCANNER |
| Парткод: | 2AV12190 |
| Деталь: | REAR WIRE,SCANNER |
| Парткод: | 2AV12200 |
| Деталь: | SHAFT,SCANNER DRIVE |
| Парткод: | 2AV12210 |
| Деталь: | MOTOR,SCANNER |
| Парткод: | 2AV12221 |
| Деталь: | GEAR 44/16 |
| Парткод: | 2AV12230 |
| Деталь: | GEAR 26 |
| Парткод: | 2AV12240 |
| Деталь: | CONTACT GLASS ADF |
| Парткод: | 2FG12020 |
| Деталь: | MOUNT BASE,DF HINGE |
| Парткод: | 2AV12260 |
| Деталь: | MOUNT,SCANNER MOTOR |
| Парткод: | 2AV12270 |
| Деталь: | MOUNT,RELEASE SWITCH |
| Парткод: | 2AV12290 |
| Деталь: | HOLDER,ADF CONTACT GLASS |
| Парткод: | 2AV12300 |
| Деталь: | FILM A,MIRROR FRAME |
| Парткод: | 2AV12320 |
| Деталь: | MOUNT ORIGINAL DETECTION |
| Парткод: | 2FG12010 |
| Деталь: | LOWER SEAL,SCANNER |
| Парткод: | 2AV12430 |
| Деталь: | SLIDER,SCANNER |
| Парткод: | 2AV12450 |
| Деталь: | REAR ORIGINAL SIZE INDICATOR(METRIC) |
| Парткод: | 2AV12460 |
| Деталь: | REAR ORIGINAL SIZE INDICATOR(INCH) |
| Парткод: | 2AV12470 |
| Деталь: | LABEL,ORIGINAL SIZE INDICATOR(METRIC) |
| Парткод: | 2AV12481 |
| Деталь: | LABEL,ORIGINAL SIZE INDICATOR(INCH) |
| Парткод: | 2AV12491 |
| Деталь: | COVER,ISU |
| Парткод: | 2AV12520 |
| Деталь: | REAR BUSHING,DEVELOPING ROLLER (B) |
| Парткод: | 72914480 |
| Деталь: | STOPPER,WIRE |
| Парткод: | 2AV12350 |
| Деталь: | MOUNT DF CONNECTOR |
| Парткод: | 2BJ26180 |
| Деталь: | WIRE DF (KM-5035) |
| Парткод: | 2FG27360 |
| Деталь: | WIRE SCANNER (KM-4035) |
| Парткод: | 2FF27010 |
| Деталь: | WIRE SCAN (KM-3035) |
| Парткод: | 2FD27010 |
| Деталь: | GUIDE,SCANNER WIRE |
| Парткод: | 18512340 |
| Деталь: | Holder FFC |
| Парткод: | 2AC12300 |
| Деталь: | GUIDE,RELEASE SWITCH |
| Парткод: | 2AC12360 |
| Деталь: | SWITCH,RELEASE DETECTION |
| Парткод: | 2AC12370 |
| Деталь: | SPRING,RELEASE SWITCH |
| Парткод: | 2AC12380 |
| Деталь: | WIRE INVERTER |
| Парткод: | 2FG27100 |
| Деталь: | FILM,FFC |
| Парткод: | 2AR12200 |
| Деталь: | LEFT ORIGINAL SIZE INDICATOR |
| Парткод: | 2A305070 |
| Деталь: | LABEL,CAUTION CONTACT GLASS |
| Парткод: | 2A105180 |
| Деталь: | CUSHION,CONTACT GLASS |
| Парткод: | 29812291 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | CONTACT GLASS |
| Парткод: | 35912010 |
| Деталь: | PULLEY,SCANNER DRUM |
| Парткод: | 35912060 |
| Деталь: | STANDARD PLATE,SHADING |
| Парткод: | 2BC12130 |
| Деталь: | SPRING,MIRROR HOLDER |
| Парткод: | 35912210 |
| Деталь: | GUIDE FFC2 |
| Парткод: | 35912360 |
| Деталь: | FRONT ORIGINAL SIZE INDICATOR |
| Парткод: | 35912490 |
| Деталь: | SPONGE,ORIGINAL SIZE INDICATOR |
| Парткод: | 35912531 |
| Деталь: | SENSOR ORIGINAL |
| Парткод: | 2C927090 |
| Деталь: | PI SWITCH,OPTICAL SECTION |
| Парткод: | 72127100 |
| Деталь: | COVER,OPERATION UNIT WIRE |
| Парткод: | 2AV12310 |
| Деталь: | INVERTER PCB |
| Парткод: | 2AV28080 |
| Деталь: | FRONT FILM SCANNER |
| Парткод: | 2BJ12080 |
| Деталь: | EDGING,EDS-1717U |
| Парткод: | M2104220 |
| Деталь: | RECEPTACLE,52918-4615(MOLEX) |
| Парткод: | J0388460 |
| Деталь: | SPRING,SCANNER TENSION |
| Парткод: | 2AV12500 |
| Деталь: | GROUND PLATE A SCANNER |
| Парткод: | 2BJ12040 |
| Деталь: | SPRING,THRUST |
| Парткод: | 34918200 |
| Деталь: | COVER TOTAL COUNTER |
| Парткод: | 2FG04020 |
| Деталь: | SHEET SCANNER DRIVE |
| Парткод: | 2BJ27330 |
| Деталь: | HOLDER SCANNER PCB |
| Парткод: | 2BJ12030 |
| Деталь: | WIRE SADDLE,YMC-10-0(KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | WIRE OPERATION(C) |
| Парткод: | 2FG27340 |
| Деталь: | GROUND PLATE B SCANNER |
| Парткод: | 2BJ12050 |
| Деталь: | MINIATURE CLAMPUAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE ORIGINAL SENSOR |
| Парткод: | 2FG27350 |
| Деталь: | WIRE,SCANNER SWITCH |
| Парткод: | 2AR27520 |
| Деталь: | WIRE RELEASE SW |
| Парткод: | 2BJ27170 |
| Деталь: | GROUND PLATE D SCANNER |
| Парткод: | 2BJ12070 |
| Деталь: | GROUND PLATE C SCANNER |
| Парткод: | 2BJ12060 |
| Деталь: | CORE ATFC-201010 |
| Парткод: | 2FG27510 |
| Деталь: | CLAMP,EMT-3N(TAKEUCHI) |
| Парткод: | M7005010 |
| Деталь: | CLAMP,EMT-6N(TAKEUCHI) |
| Парткод: | M7005020 |
| Деталь: | CORE 15-26X13 |
| Парткод: | 2AV27440 |
| Деталь: | GASKET CCD A |
| Парткод: | 2FG27560 |
| Деталь: | SET,PLATEN COVER TYPE D |
| Парткод: | 2CX82010 |
| Деталь: | ORIGINAL POCKET |
| Парткод: | 60904280 |
| Деталь: | COVER,PLATEN |
| Парткод: | 2A612800 |
| Деталь: | HINGE,ORIGINAL HOLDER |
| Парткод: | 2A612820 |
| Деталь: | MAT,ORIGINAL HOLDER |
| Парткод: | 2A612810 |
| Деталь: | BINDING TAP-TITE P SCREW M4X16 |
| Парткод: | B8014160 |
| Деталь: | STOPPER RELEASE SWITCH |
| Парткод: | 2C912630 |
| Деталь: | BINDING TAP-TITE P SCREW M3X12 |
| Парткод: | B8013120 |
| Деталь: | SHAFT CHANGE PULLEY |
| Парткод: | 2BL21361 |
| Деталь: | PULLEY FEED SHIFT |
| Парткод: | 2BL21330 |
| Деталь: | GUIDE EXIT L |
| Парткод: | 2BL21290 |
| Деталь: | SPRING CHANGE PULLEY |
| Парткод: | 2BL21340 |
| Деталь: | MOUNT REAR GUIDE |
| Парткод: | 2FG20180 |
| Деталь: | REAR GUIDE FIXING |
| Парткод: | 2FG20170 |
| Деталь: | FULCRUM PIN,FIXING |
| Парткод: | 34920170 |
| Деталь: | CLAW PRESS ROLLER |
| Парткод: | 2BL20350 |
| Деталь: | SHAFT,PRESSURE ROLLER SEPARATION CLAW |
| Парткод: | 2AR20510 |
| Деталь: | SPRING,SEPARATION CLAW |
| Парткод: | 2BL20360 |
| Деталь: | SPRING,DEVELOPING ROCK |
| Парткод: | 65009050 |
| Деталь: | GUIDE FEED SHIFT L |
| Парткод: | 2BL21410 |
| Деталь: | LEFT COVER MIDDLE 1 |
| Парткод: | 2BL04510 |
| Деталь: | GROUND PLATE LEFT FAN |
| Парткод: | 2BL23110 |
| Деталь: | PLATE LEFT COVER M |
| Парткод: | 2BL04620 |
| Деталь: | GROUND PLATE LEFT B |
| Парткод: | 2BL04700 |
| Деталь: | SHAFT L COVER LOCK M |
| Парткод: | 2BL04540 |
| Деталь: | LEVER L COVER LOCK M |
| Парткод: | 2BL04550 |
| Деталь: | SPRING L COVER LOCK |
| Парткод: | 2BL04560 |
| Деталь: | LEVER COVER RELEASE |
| Парткод: | 2BL04600 |
| Деталь: | PIN,ORIGINAL HOLDER |
| Парткод: | 73912281 |
| Деталь: | STRAP COVER |
| Парткод: | 2BL04680 |
| Деталь: | GUIDE LEFT COVER M |
| Парткод: | 2BL21320 |
| Деталь: | FAN MOTOR 4 |
| Парткод: | 2FG27080 |
| Деталь: | WIRE CONVEYING FAN |
| Парткод: | 2BL27300 |
| Деталь: | FILM WIRE PROTECT |
| Парткод: | 2BL21460 |
| Деталь: | COVER EXIT L |
| Парткод: | 2BJ04510 |
| Деталь: | FRONT PLATE EXIT L |
| Парткод: | 2BJ04520 |
| Деталь: | GUIDE CHANGE UP |
| Парткод: | 2BJ21010 |
| Деталь: | REAR PLATE EXIT L |
| Парткод: | 2BJ04530 |
| Деталь: | LEVER GUIDE CHANGE U |
| Парткод: | 2BJ21021 |
| Деталь: | SPRING CHANGE UP |
| Парткод: | 2BJ21030 |
| Деталь: | LEVER CHANGE UP B |
| Парткод: | 2BJ21040 |
| Деталь: | LEFT COVER FEED |
| Парткод: | 2BL06100 |
| Деталь: | SPRING FEED |
| Парткод: | 2BL06340 |
| Деталь: | SHAFT FEED PULLEY |
| Парткод: | 2BL06211 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL16080 |
| Деталь: | STRAP RELEASE |
| Парткод: | 2BL06960 |
| Деталь: | RETAINING PIN,VERTICAL CONVEYING |
| Парткод: | 2AR07540 |
| Деталь: | LAVEL LEFT COVER |
| Парткод: | 2BL05050 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | 2BL05110 |
| Деталь: | FILM WIRE PROTECT B |
| Парткод: | 2BL21500 |
| Деталь: | LABEL DRUM CAUTION |
| Парткод: | 2BL05270 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | SPONGE LEFT FAN |
| Парткод: | 2BL23170 |
| Деталь: | GUIDE FILM DU |
| Парткод: | 2BL21490 |
| Деталь: | PARTS,FIXING ASSY, 110 |
| Парткод: | 2FG93090 |
| Деталь: | PARTS,FIXING ASSY120,SP |
| Парткод: | 2FG93030 |
| Деталь: | PARTS,FIXING ASSY230,SP |
| Парткод: | 2FG93040 |
| Деталь: | LOWER FRAME FIXING A |
| Парткод: | 2FG20020 |
| Деталь: | LOWER COVER FRAME |
| Парткод: | 2BL20310 |
| Деталь: | STATIC ELIMINATOR,HEAT ROLLER |
| Парткод: | 34820310 |
| Деталь: | PLATE SPRING FIXING |
| Парткод: | 2BL20230 |
| Деталь: | REAR FRAME FIXING |
| Парткод: | 2FG20040 |
| Деталь: | REAR PRESSING PLATE |
| Парткод: | 2FG20300 |
| Деталь: | FRONT FRAME FIXING |
| Парткод: | 2FG20030 |
| Деталь: | COVER FIXING WIRE |
| Парткод: | 2BL20290 |
| Деталь: | FRONT PRESSING PLATE |
| Парткод: | 2FG20290 |
| Деталь: | MOUNT THERMISTOR |
| Парткод: | 2BL20210 |
| Деталь: | THERMISTOR FIXING |
| Парткод: | 2FG20210 |
| Деталь: | ROLLER HEAT |
| Парткод: | 2FG20050 |
| Деталь: | BUSHING HEAT ROLLER |
| Парткод: | 2FG20190 |
| Деталь: | BEARING HEAT ROLLER |
| Парткод: | 2FG20230 |
| Деталь: | GEAR 49 HEAT ROLLER |
| Парткод: | 2FG20070 |
| Деталь: | STOPPER HEAT ROLLER |
| Парткод: | 2FG20200 |
| Деталь: | ROLLER PRESS |
| Парткод: | 2FG20060 |
| Деталь: | BEARING PRESS ROLLER |
| Парткод: | 2FG20310 |
| Деталь: | SPRING PRESSURE |
| Парткод: | 2FG20240 |
| Деталь: | NUT FUSER |
| Парткод: | 2BM20420 |
| Деталь: | HEATER M110 FIXING |
| Парткод: | 2FG20320 |
| Деталь: | HEATER M120 FIXING |
| Парткод: | 2FG20120 |
| Деталь: | HEATER M230 FIXING |
| Парткод: | 2FG20140 |
| Деталь: | HEATER S110 FIXING |
| Парткод: | 2FG20330 |
| Деталь: | HEATER S120 FIXING |
| Парткод: | 2FG20130 |
| Деталь: | HEATER S230 FIXING |
| Парткод: | 2FG20150 |
| Деталь: | WIRE FIXING UNIT |
| Парткод: | 2BL27130 |
| Деталь: | THERMOSTAT FIXING |
| Парткод: | 2FG20220 |
| Деталь: | GEAR FIXING Z33 |
| Парткод: | 2BL20260 |
| Деталь: | UPPER FRAME FIXING A |
| Парткод: | 2FG20010 |
| Деталь: | UPPER COVER FRAME |
| Парткод: | 2BL20300 |
| Деталь: | CLAW HEAT ROLLER |
| Парткод: | 2BL20080 |
| Деталь: | SPRING CLAW |
| Парткод: | 2BL20240 |
| Деталь: | PCB FIXING ASSY(C) |
| Парткод: | 2FG01080 |
| Деталь: | HOLDER PRESS SE |
| Парткод: | 2BL20320 |
| Деталь: | STATIC ELIMINATOR PRESS |
| Парткод: | 2BL20330 |
| Деталь: | GROUND PLATE FIXING |
| Парткод: | 2FG20280 |
| Деталь: | THERMISTER FIXING UC |
| Парткод: | 2FG20340 |
| Деталь: | PARTS,EXIT UNIT SP (J) |
| Парткод: | 2BJ93110 |
| Деталь: | PARTS,EXIT UNIT,SP |
| Парткод: | 2BJ93100 |
| Деталь: | FRAME EXIT UP |
| Парткод: | 2BL21040 |
| Деталь: | PLATE EARTH EXIT F |
| Парткод: | 2BL21170 |
| Деталь: | ROLLER FEED SHIFT |
| Парткод: | 2BL21030 |
| Деталь: | ROLLER EJECT J |
| Парткод: | 2BJ21050 |
| Деталь: | ROLLER EXIT |
| Парткод: | 2BL21020 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | GEAR EXIT Z20 |
| Парткод: | 2BL21430 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | PULLEY ONEWAY T30 |
| Парткод: | 2BL21211 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | COLLAR BELT |
| Парткод: | 2BL22580 |
| Деталь: | GEAR EXIT Z19 |
| Парткод: | 2BL21220 |
| Деталь: | JOINT EXIT |
| Парткод: | 2BL21200 |
| Деталь: | GEAR EXIT JOINT Z26S |
| Парткод: | 2BL21390 |
| Деталь: | SWITCH,FEED |
| Парткод: | 35327400 |
| Деталь: | ACTUATOR EXIT L |
| Парткод: | 2BL21130 |
| Деталь: | SPRING ACTUATOR L |
| Парткод: | 2BL21260 |
| Деталь: | SOLENOID,FEED SHIFT |
| Парткод: | 3AZ21890 |
| Деталь: | SPRING EXIT CHANGE |
| Парткод: | 2BL21440 |
| Деталь: | BKT SOLENOID |
| Парткод: | 2BL21190 |
| Деталь: | EDGING,EDS-0607M(KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | BKT DISCHARGER |
| Парткод: | 2BL21160 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | 34821100 |
| Деталь: | PLATE EARTH EXIT R |
| Парткод: | 2BL21180 |
| Деталь: | FRAME EXIT |
| Парткод: | 2BL21010 |
| Деталь: | PLATE EARTH CHANGE |
| Парткод: | 2BL21470 |
| Деталь: | GUIDE EXIT CHANGE |
| Парткод: | 2BL21080 |
| Деталь: | CUT WASHER 6 |
| Парткод: | 2BL21510 |
| Деталь: | LEVER GUIDE CHANGE B |
| Парткод: | 2BL21370 |
| Деталь: | SPRING FEED SHIFT |
| Парткод: | 2BL21270 |
| Деталь: | LEVER GUIDE CHANGE |
| Парткод: | 2BL21100 |
| Деталь: | SPRING EXIT JOINT |
| Парткод: | 2BL21400 |
| Деталь: | ACTUATOR EXIT R |
| Парткод: | 2BL21120 |
| Деталь: | SPRING ACTUATOR R |
| Парткод: | 2BL21250 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | 2BL21070 |
| Деталь: | SHAFT EXIT PULLEY |
| Парткод: | 2BL21060 |
| Деталь: | PULLEY EXIT B |
| Парткод: | 2BL21450 |
| Деталь: | PULLEY EXIT C |
| Парткод: | 2BL21520 |
| Деталь: | WIRE EJECT(C) |
| Парткод: | 2BJ27160 |
| Деталь: | PIN EXIT |
| Парткод: | 2BL21420 |
| Деталь: | MINIATURE CLAMPUAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | POLYESTER SLIDER WASHER 6.2X12X0.25T |
| Парткод: | C2891120 |
| Деталь: | PARTS,DRUM ASSY,SP (KM-5035/4035) |
| Парткод: | 2FG93010 |
| Деталь: | PARTS,DRUM ASSY (KM-3035) |
| Парткод: | 2BJ93020 |
| Деталь: | GEAR CL ROLLER 15 |
| Парткод: | 2BL18870 |
| Деталь: | PARTS,LAMP CLEANING ASSY |
| Парткод: | 2BL93420 |
| Деталь: | SPONGE LOWER SEAL |
| Парткод: | 2BL18560 |
| Деталь: | PARTS MAIN-C,MC700 |
| Парткод: | 2BL93090 |
| Деталь: | PARTS,CLAW SEPARATION |
| Парткод: | 2BL93310 |
| Деталь: | LOWER SEAL CLEANING |
| Парткод: | 2BL18070 |
| Деталь: | HANDLE DRUM |
| Парткод: | 2BL18320 |
| Деталь: | BLADE CLEANING |
| Парткод: | 2BL18300 |
| Деталь: | BUSHING DRUM A |
| Парткод: | 2BL18630 |
| Деталь: | GEAR IDLE 15 |
| Парткод: | 2BL18170 |
| Деталь: | GEAR CL ROLLER 16 |
| Парткод: | 2BL18880 |
| Деталь: | GEAR SPIRAL 16 |
| Парткод: | 2BL18160 |
| Деталь: | LABEL DRUM |
| Парткод: | 2BL05080 |
| Деталь: | BASE CONVEYING 1 |
| Парткод: | 2BL16010 |
| Деталь: | PLATE TRANS UNIT GND |
| Парткод: | 2BL16160 |
| Деталь: | PLATE PAPER GUIDE |
| Парткод: | 2BL16120 |
| Деталь: | PLATE TRANS B |
| Парткод: | 2BL16150 |
| Деталь: | PLATE SEPARATION B |
| Парткод: | 2BL16170 |
| Деталь: | SPRING FEED |
| Парткод: | 2BL16090 |
| Деталь: | SHAFT FEED |
| Парткод: | 2BL16071 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BL16080 |
| Деталь: | FRONT SPRING REGIST |
| Парткод: | 2BL16270 |
| Деталь: | REAR SPRING REGIST |
| Парткод: | 2BL16280 |
| Деталь: | ROLLER REGIST |
| Парткод: | 2FG16020 |
| Деталь: | BUSHING REGIST |
| Парткод: | 2BL16260 |
| Деталь: | STOPPER BUSH |
| Парткод: | 2BL16030 |
| Деталь: | GEAR REGIST Z18 |
| Парткод: | 2BL16060 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | GUIDE REGIST F |
| Парткод: | 2BL16130 |
| Цена: | 330 ₽ |
| Деталь: | GUIDE FEED F |
| Парткод: | 2BL16250 |
| Деталь: | SHAFT CONVEYING |
| Парткод: | 2BL16210 |
| Деталь: | SPRING CONVEYING B |
| Парткод: | 2BL16240 |
| Деталь: | HOOK CONVEYING |
| Парткод: | 2BL16190 |
| Деталь: | SPRING CONVEYING |
| Парткод: | 2BL16200 |
| Деталь: | HANDLE CONVEYING |
| Парткод: | 2BL16180 |
| Деталь: | STRAP CONVEYING B |
| Парткод: | 2BL16110 |
| Деталь: | STRAP CONVEYING A |
| Парткод: | 2BL16100 |
| Деталь: | TR-700 TRANSFER UNIT (KM-3035) |
| Парткод: | 2BK93070 |
| Деталь: | TR-701 TRANSFER UNIT (KM-5035/KM-4035) |
| Парткод: | 2BL93030 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 2BL17021 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BL17170 |
| Деталь: | PULLEY TRANS ROLLER |
| Парткод: | 2BL17040 |
| Деталь: | GEAR TRANS Z25H |
| Парткод: | 2BL17090 |
| Деталь: | COLLAR TRANS ROLLER |
| Парткод: | 2BL17030 |
| Деталь: | LEFT GUIDE TRANSFER |
| Парткод: | 2BL17150 |
| Деталь: | SHEET TRANS GUIDE |
| Парткод: | 2BL17140 |
| Деталь: | HOUSING TRANSFER |
| Парткод: | 2BL17010 |
| Деталь: | BRUSH SEPARATION B (KM-3035) |
| Парткод: | 2BK17010 |
| Деталь: | BRUSH SEPARATION (KM-5035/KM-4035) |
| Парткод: | 2BL17110 |
| Деталь: | HOLDER SEPARATION |
| Парткод: | 2BL17100 |
| Деталь: | PLATE TRANS UNIT |
| Парткод: | 2BL17050 |
| Деталь: | BUSH TRANS ROLLER |
| Парткод: | 2BL17060 |
| Деталь: | SPRING TRANS R |
| Парткод: | 2BL17080 |
| Деталь: | SPRING TRANS F |
| Парткод: | 2BL17070 |
| Деталь: | SPRING LEFT GUIDE |
| Парткод: | 2BL17180 |
| Деталь: | REINFORCEMENT TRANS |
| Парткод: | 2BL17190 |
| Деталь: | BUSHING,CLEANING BLADE SHAFT |
| Парткод: | 75718040 |
| Деталь: | SPONGE LEFT GUIDE |
| Парткод: | 2BL17210 |
| Деталь: | PULLEY REGIST |
| Парткод: | 2BL07960 |
| Деталь: | CUT WASHER 10 |
| Парткод: | 2BL07970 |
| Деталь: | UNDER CLEANER REGIST |
| Парткод: | 2BL07950 |
| Цена: | 1 500 ₽ |
| Деталь: | CUT WASHER 3 |
| Парткод: | 2BL16290 |
| Деталь: | PLATE MID FEED UNIT |
| Парткод: | 2FG16010 |
| Деталь: | WIRE DUPLEX(C) |
| Парткод: | 3CX27010 |
| Деталь: | GEAR 25 |
| Парткод: | 2AL06110 |
| Деталь: | FRAME DU |
| Парткод: | 2BL07010 |
| Деталь: | ROLLER DU FEED UP |
| Парткод: | 2BL07020 |
| Деталь: | ROLLER DU FEED LOW |
| Парткод: | 2BL07030 |
| Деталь: | PULLEY DU |
| Парткод: | 2BL07040 |
| Деталь: | SHAFT DU PULLEY |
| Парткод: | 2BL07050 |
| Деталь: | SPRING DU PULLEY |
| Парткод: | 2BL07060 |
| Деталь: | JOINT DU |
| Парткод: | 2BL07070 |
| Деталь: | SPRING DU JOINT |
| Парткод: | 2BL07080 |
| Деталь: | ACTUATOR DU |
| Парткод: | 2BL07090 |
| Деталь: | PLATE EARTH DU |
| Парткод: | 2BL07110 |
| Деталь: | SPRING DU ACT. |
| Парткод: | 2BL07130 |
| Деталь: | PULLEY EXIT T30 |
| Парткод: | 2BL21230 |
| Деталь: | BELT EXIT P2M212 |
| Парткод: | 2BL21240 |
| Деталь: | SWITCH PI |
| Парткод: | 2BL27450 |
| Деталь: | CLUTCH FEED |
| Парткод: | 2BL27500 |
| Деталь: | STOPPER 5 |
| Парткод: | 34806150 |
| Деталь: | STOPPER 6 |
| Парткод: | 34806480 |
| Деталь: | GEAR 20,IDLE |
| Парткод: | 66506630 |
| Деталь: | BUSHING 8 |
| Парткод: | 67322230 |
| Деталь: | BUSH, 6 |
| Парткод: | 73210450 |
| Деталь: | PLATE NUT DU |
| Парткод: | 2BL07120 |
| Деталь: | FRONT FRAME |
| Парткод: | 2BL02010 |
| Деталь: | REAR FRAME |
| Парткод: | 2BL02020 |
| Деталь: | BASE |
| Парткод: | 2BL02030 |
| Деталь: | BASE MIDDLE |
| Парткод: | 2BL02040 |
| Деталь: | UPPER LEFT PLATE |
| Парткод: | 2BJ02040 |
| Деталь: | UPPER FRONT FRAME |
| Парткод: | 2BJ02010 |
| Деталь: | UPPER REAR FRAME |
| Парткод: | 2BJ02020 |
| Деталь: | UPPER RIGHT PIPE |
| Парткод: | 2BJ02030 |
| Деталь: | LABEL RADIATION |
| Парткод: | 2BL05150 |
| Деталь: | LOWER LEFT REINFORCEMENT |
| Парткод: | 2AR02060 |
| Деталь: | LEFT RAIL,CASSETTE |
| Парткод: | 2AR07140 |
| Деталь: | PULLEY,CASSETTE RAIL |
| Парткод: | 2AR07800 |
| Деталь: | FRONT PIN,CASSETTE RAIL |
| Парткод: | 2AR07810 |
| Деталь: | REAR PIN,CASSETTE RAIL |
| Парткод: | 2AR07820 |
| Деталь: | EDGING,EDS-0607M(KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | WIRE SADDLE,YMC-10-0(KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | GASKET SHIELD B |
| Парткод: | 2BJ27260 |
| Деталь: | LOWER RIGHT REINFORCEMENT |
| Парткод: | 2AR02050 |
| Деталь: | UPPER PLATE FIXING |
| Парткод: | 2BL02100 |
| Деталь: | UPPER PLATE DRUM |
| Парткод: | 2BL02060 |
| Деталь: | LOWER PLATE CONT |
| Парткод: | 2BL02130 |
| Деталь: | LOWER BASE LSU |
| Парткод: | 2BL02050 |
| Деталь: | HOLDER,FULCRUM |
| Парткод: | 2BJ02120 |
| Деталь: | HOLDER,CASSETTE STOPPER |
| Парткод: | 77906291 |
| Деталь: | HANDLE MACHINE |
| Парткод: | 2BL02140 |
| Деталь: | SPRING BYPASS RET |
| Парткод: | 2BL06840 |
| Деталь: | BASE RUBBER |
| Парткод: | 2AR02180 |
| Деталь: | UPPER RIGHT PLATE |
| Парткод: | 2BL02120 |
| Деталь: | RIGHT HANDLE MACHINE |
| Парткод: | 2BL02180 |
| Деталь: | MOUNT RIGHT HANDLE |
| Парткод: | 2BL02150 |
| Деталь: | RIGHT MOUNT ISU |
| Парткод: | 2BJ02050 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BL06590 |
| Деталь: | MOUNT HINGE S |
| Парткод: | 2BL04470 |
| Деталь: | GROUND PLATE MIDDLE |
| Парткод: | 2BL06410 |
| Деталь: | COVER,CASSETTE RAIL |
| Парткод: | 2AR07720 |
| Деталь: | GROUND PLATE REAR COVER |
| Парткод: | 2BJ26190 |
| Деталь: | MOUNT REAR COVER |
| Парткод: | 2BL02200 |
| Деталь: | FULCRUM PLATE,MIDDLE TRAY |
| Парткод: | 2BJ02110 |
| Деталь: | REAR MOUNT ISU |
| Парткод: | 2BJ02070 |
| Деталь: | FRONT MOUNT ISU |
| Парткод: | 2BJ02060 |
| Деталь: | MOUNT COVER R |
| Парткод: | 2BJ02080 |
| Деталь: | MOUNT COVER L |
| Парткод: | 2BJ02090 |
| Деталь: | PIN HANDLE |
| Парткод: | 2BL02170 |
| Деталь: | RECEPTACLE,QR/P15-8S-C(02)(HIROSE) |
| Парткод: | J0464080 |
| Деталь: | MOUNT,PAPER FEED DRAWER |
| Парткод: | 2AR07710 |
| Деталь: | JUNCTION WIRING,PRIMARY PAPER FEED UNIT |
| Парткод: | 2AR27600 |
| Деталь: | RETAINING PIN,DRAWER |
| Парткод: | 33927450 |
| Деталь: | LABEL L,HIGH TEMPERATURE CAUTION(EXP) |
| Парткод: | 20305130 |
| Деталь: | HEATER,CASSETTE (120) |
| Парткод: | 33960010 |
| Деталь: | BINDING BAND SG-130 |
| Парткод: | M2107120 |
| Деталь: | LOWER COVER OP (1/2) |
| Парткод: | 2BJ04170 |
| Деталь: | SHEET TABLET |
| Парткод: | 2BJ25370 |
| Деталь: | UPPER KEY FUNCTION |
| Парткод: | 2BJ25101 |
| Деталь: | KEY OPERATION 10 |
| Парткод: | 2BJ25020 |
| Деталь: | KEY PRINT RS |
| Парткод: | 2BJ25440 |
| Деталь: | KEY PRINT E |
| Парткод: | 2BJ25300 |
| Деталь: | KEY STOP |
| Парткод: | 2BJ25040 |
| Деталь: | KEY RESET |
| Парткод: | 2BJ25050 |
| Деталь: | KEY SAVER |
| Парткод: | 2BJ25060 |
| Деталь: | KEY INTERRUPT |
| Парткод: | 2BJ25070 |
| Деталь: | KEY CONTROL |
| Парткод: | 2BJ25080 |
| Деталь: | KEY INIT |
| Парткод: | 2BJ25090 |
| Деталь: | VOLUME OPE UNIT |
| Парткод: | 2BJ25250 |
| Деталь: | BARRIER TABLET |
| Парткод: | 2BJ25240 |
| Деталь: | LEFT DUST SHIELD |
| Парткод: | 2BJ25210 |
| Деталь: | RIGHT DUST SHIELD |
| Парткод: | 2BJ25230 |
| Деталь: | OPERATION UNIT PCB ASSY B |
| Парткод: | 2CX01050 |
| Деталь: | TABLET OPERATION |
| Парткод: | 2FG27150 |
| Деталь: | SPONGE LCD A |
| Парткод: | 2BJ25270 |
| Деталь: | SPONGE LCDB |
| Парткод: | 2BJ25280 |
| Деталь: | LCD PCB |
| Парткод: | 2BJ28030 |
| Деталь: | WIRE LCD |
| Парткод: | 2BJ27140 |
| Деталь: | GROUND PLATE LCD A |
| Парткод: | 2BJ04220 |
| Деталь: | GROUND PLATE LCD C |
| Парткод: | 2BJ04240 |
| Деталь: | CENTER DUST SHIELD |
| Парткод: | 2BJ25220 |
| Деталь: | OPERATION UNIT PCB ASSY A |
| Парткод: | 2CX01100 |
| Деталь: | GROUND PLATE LCD B |
| Парткод: | 2BJ04230 |
| Деталь: | SHIELD LCD |
| Парткод: | 2BJ04210 |
| Деталь: | RIGHT MOUNT COVER |
| Парткод: | 2BJ04130 |
| Деталь: | MIDDLE MOUNT COVER |
| Парткод: | 2BJ04120 |
| Деталь: | EDGING,EDS-0607M(KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | LEFT MOUNT COVER |
| Парткод: | 2BJ04110 |
| Деталь: | RIGHT LID OPE UNIT |
| Парткод: | 2BJ25201 |
| Деталь: | LEFT KEY COPIER RS |
| Парткод: | 2BJ25450 |
| Деталь: | LEFT KEY COPIER E |
| Парткод: | 2BJ25310 |
| Деталь: | LEFT KEY PRINTER RS |
| Парткод: | 2BJ25460 |
| Деталь: | LEFT KEY PRINTER E |
| Парткод: | 2BJ25320 |
| Деталь: | LEFT KEY SCANNER RS |
| Парткод: | 2BJ25470 |
| Деталь: | LEFT KEY SCANNER E |
| Парткод: | 2BJ25330 |
| Деталь: | LEFT KEY FAX RS |
| Парткод: | 2BJ25480 |
| Деталь: | LEFT KEY FAX E |
| Парткод: | 2BJ25340 |
| Деталь: | LEFT LID OPE UNIT |
| Парткод: | 2BJ25151 |
| Деталь: | LEFT LID COPIER |
| Парткод: | 2BJ25161 |
| Деталь: | LEFT LID PRINTER |
| Парткод: | 2BJ25171 |
| Деталь: | LEFT LID SCANNER |
| Парткод: | 2BJ25181 |
| Деталь: | LEFT LID FAX |
| Парткод: | 2BJ25191 |
| Деталь: | COVER OPE (TW) |
| Парткод: | 2FG25010 |
| Деталь: | COVER OPE UNIT E |
| Парткод: | 2BG25080 |
| Деталь: | SPACER STOP KEY ASSY |
| Парткод: | 2BJ68320 |
| Деталь: | SHEET OPERATION PCB |
| Парткод: | 2BJ25380 |
| Деталь: | SHEET FUNCTION (EXP) |
| Парткод: | 2BC25020 |
| Деталь: | RETAINER LCD |
| Парткод: | 2BJ25390 |
| Деталь: | SHEET LCD A |
| Парткод: | 2BJ25400 |
| Деталь: | SHEET LCDB |
| Парткод: | 2BJ25410 |
| Деталь: | SHEET LCD C |
| Парткод: | 2BJ25420 |
| Деталь: | SPACER,KGPS-5RF(KITAGAWA) |
| Парткод: | M2108880 |
| Деталь: | SPACER,KGPS-8RF(KITAGAWA) |
| Парткод: | M2108850 |
| Деталь: | UPPER COVER OP |
| Парткод: | 2BJ04160 |
| Деталь: | SET DT-70 |
| Парткод: | 2BH82010 |
| Деталь: | WING TRAY ASSY |
| Парткод: | 2BJ60500 |
| Деталь: | MOUNT WING TRAY |
| Парткод: | 2BJ60510 |
| Деталь: | UPPER WING TRAY |
| Парткод: | 2BJ60520 |
| Деталь: | LOWER WING TRAY |
| Парткод: | 2BJ60530 |
| Деталь: | RAIL WING TRAY |
| Парткод: | 2BJ60540 |
| Деталь: | BINDING SCREW BVM3X5 (BLACK) |
| Парткод: | B1303050 |
| Деталь: | PARTS,UNIT HDD(S P) |
| Парткод: | 2FA93130 |
| Деталь: | HDD POWER PCB ASSY |
| Парткод: | 3JA01010 |
| Деталь: | SPACER CASSETTE CURSOR |
| Парткод: | 2BL68560 |
| Деталь: | GUIDE DU FEED R |
| Парткод: | 2BL21350 |
| Деталь: | MOUNT TRAY EJECT |
| Парткод: | 2BL04320 |
| Деталь: | MOUNT HINGE |
| Парткод: | 2BL04220 |
| Деталь: | COVER EXIT LOW |
| Парткод: | 2BL04100 |
| Деталь: | MOUNT LEFT FRONT COVER |
| Парткод: | 2BJ04150 |
| Деталь: | RIGHT COVER TRAY |
| Парткод: | 2BJ04050 |
| Деталь: | REAR COVER TRAY |
| Парткод: | 2BJ04030 |
| Деталь: | UPPER EJECT COVER |
| Парткод: | 2BJ04040 |
| Деталь: | REAR COVER SCANNER |
| Парткод: | 2AV04100 |
| Деталь: | UPPER LEFT COVER A |
| Парткод: | 2BJ04060 |
| Деталь: | UPPER RIGHT COVER A |
| Парткод: | 2BJ04080 |
| Деталь: | LEVER CONT RELEASE |
| Парткод: | 2BL04200 |
| Деталь: | INNER RIGHT COVER |
| Парткод: | 2BL04090 |
| Деталь: | TRAY EJECT |
| Парткод: | 2BL04040 |
| Деталь: | RIGHT FRONT COVER (KM-5035) |
| Парткод: | 2FG04010 |
| Деталь: | RIGHT FRONT COVER (KM-4035) |
| Парткод: | 2FF04010 |
| Деталь: | RIGHT FRONT COVER (KM-3035) |
| Парткод: | 2FD04010 |
| Деталь: | FRONT COVER MIDDLE |
| Парткод: | 2BL04910 |
| Деталь: | MAGNET CATCH |
| Парткод: | 60804120 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 2BL04330 |
| Деталь: | FRONT HINGE COVER P |
| Парткод: | 2BL04350 |
| Деталь: | PIN COVER HINGE |
| Парткод: | 2BL04190 |
| Деталь: | LEFT COVER CASSETTE |
| Парткод: | 2BL04150 |
| Деталь: | Left front cover |
| Парткод: | 2BJ04010 |
| Деталь: | UPPER LEFT COVER B |
| Парткод: | 2BJ04070 |
| Деталь: | Rear Left Cover |
| Парткод: | 2BL04120 |
| Деталь: | FRONT LEFT COVER |
| Парткод: | 2BL04110 |
| Деталь: | LID COVER LEFT |
| Парткод: | 2BL04300 |
| Деталь: | RIGHT COVER |
| Парткод: | 2BL04130 |
| Деталь: | REAR COVER A |
| Парткод: | 2FG04030 |
| Деталь: | UPPER RIGHT COVER B (1/2) |
| Парткод: | 2BJ04090 |
| Деталь: | PIN,TONER HOPPER |
| Парткод: | 74315200 |
| Деталь: | PIN,OPTION |
| Парткод: | 2A126130 |
| Деталь: | TRAY SUB C |
| Парткод: | 2BK04020 |
| Деталь: | STOPPER PAPER C |
| Парткод: | 2BK04030 |
| Деталь: | PIN COVER HINGE S |
| Парткод: | 2BL04840 |
| Деталь: | FRONT COVER HINGE S |
| Парткод: | 2BL04480 |
| Деталь: | LABEL SEP CLEANING |
| Парткод: | 2BL05070 |
| Деталь: | LABEL CONVEYING JAM |
| Парткод: | 2BL05120 |
| Деталь: | BRUSH CLEANER |
| Парткод: | 2BL16220 |
| Деталь: | COVER FLYWHEEL |
| Парткод: | 2BJ04250 |
| Деталь: | FILM HINGE |
| Парткод: | 2BL04880 |
| Деталь: | STOPPER PAPER SUB |
| Парткод: | 2BK04040 |
| Деталь: | PIN COVER |
| Парткод: | 2BL04410 |
| Деталь: | PIN,HOOK LEVER |
| Парткод: | 73926080 |
| Деталь: | SPONGE FRONT |
| Парткод: | 2BL06620 |
| Деталь: | LABEL OFF |
| Парткод: | 2BL05240 |
| Деталь: | PARTS,LASER UNIT,LK700 |
| Парткод: | 2BL93141 |
| Деталь: | FRONT MOUNT HOUSING |
| Парткод: | 2BL13120 |
| Деталь: | PIN TENSION PULLEY |
| Парткод: | 76610320 |
| Деталь: | SPRING FIX LSU |
| Парткод: | 2BL13290 |
| Деталь: | FRONT ADJUSTING LSU |
| Парткод: | 2BL13070 |
| Деталь: | REAR ADJUSTING LSU |
| Парткод: | 2BL13060 |
| Деталь: | ADJUSTING PLT LSU |
| Парткод: | 2BL13250 |
| Деталь: | WIRE LSU(C) |
| Парткод: | 2BJ27200 |
| Деталь: | FILTER DUST SHIELD |
| Парткод: | 2BL23090 |
| Деталь: | MOUNT FAN |
| Парткод: | 2BL02230 |
| Деталь: | FAN COOLING(60-25) |
| Парткод: | 2BL27700 |
| Деталь: | WIRE SADDLE,YMC-10-0(KITAGAWA) |
| Парткод: | M2109330 |
| Деталь: | SPONGE FAN |
| Парткод: | 2BL02240 |
| Деталь: | WIRE DLP FAN |
| Парткод: | 2BL27330 |
| Деталь: | FILTER DUST SHIELD B |
| Парткод: | 2BL23160 |
Коды ошибок
C0030
C0070
C0100
C0110
C0150
C0160
C0170
C0210
C0240
C0250
C0280
C0320
C0420
C0440
C0450
C0470
C0610
C0630
C0640
C0820
C0830
C0860
C0870
C0880
C0890
C0900
C1010
C1020
C1030
C1040
C1100
C1110
C1120
C1130
C2000
C2500
C2600
C3100
C3200
C3300
C4000
C4010
C4200
C5300
C6000
C6020
C6050
C6400
C6410
C6420
C7300
C7400
C7410
C7450
C7800
C7810
C8010
C8030
C8140
C8170
C8180
C8190
C8210
C8220
C8300
C8310
C8320
C8330
C8340
C8350
C8360
C8370
C8380
C8390
C8410
C8420
C8430
C8440
C8450
C8460
C8470
C8480
C8500
Описание
| Error code: | C0030 |
| Description: | FAX PWB system error |
| Causes: | The FAX processing cannot be continued due to the FAX firmware error. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. |
| Error code: | C0070 |
| Description: | Toner motor |
| Causes: | Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Remedy: | 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0100 |
| Description: | Charge corona winding problem |
| Causes: | An abnormal status is output from the flash memory. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. If not repaired, replace the main PWB. |
| Error code: | C0110 |
| Description: | Backup memory data problem (main PWB) • Data in the specified area of the backup memory does not match the specified values. |
| Causes: | Problem with the backup memory data. Defective main PWB. |
| Remedy: | Problem with the backup memory data. Run maintenance item U021 to set the contents of the backup memory data again. Defective main PWB. If the C0110 is displayed after initializing the backup memory, replace the main PWB and check for correct operation. |
| Error code: | C0150 |
| Description: | Engine EEPROM reading / writing error |
| Causes: | 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing data. 2. The data read reading in 2 points mismatches 8 times continuously. 3. The read data and the write data mismatch 8 times continuously. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0160 |
| Description: | Engine PWB EEPROM data error |
| Causes: | The data read from the EEPROM is judged as abnormal. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing U021 The storage data in the EEPROM on the engine PWB is faulty. Execute U021. Executing U021 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. |
| Error code: | C0170 |
| Description: | Charger count error |
| Causes: | The values in one of the billing counters, life counter or the scanner counter mismatch between the main side and the engine side. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. Detaching and reattaching the main PWB 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0240 |
| Description: | Printer board* communication problem • The printer board does not respond 120 seconds after the power is turned on. |
| Causes: | Poor contact in the connector terminals. DIMM installed incorrectly. Defective main PWB or printer board. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC9 on the main PWB and YC5 on the printer board, and the continuity across the connector terminals. Repair or replace if necessary. DIMM installed incorrectly. Check the connection. Repair or replace if necessary. Defective main PWB or printer board. Replace the main PWB or printer board and check for correct operation. |
| Error code: | C0250 |
| Description: | Network scanner board* communication problem • The response to the alive command to the network scanner transmitted once to 30 s does not come on the contrary three consecutive times or more. • The response to the communication command transmitted to the network scanner does not return 75 s or more. |
| Causes: | Poor contact in the connector terminals. Defective main PWB or network scanner board. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the main PWB and the connector on the network scanner board, and the continuity across the connector terminals. Repair or replace if necessary. Defective main PWB or network scanner board. Replace the main PWB or network scanner board and check for correct operation. |
| Error code: | C0280 |
| Description: | Communication problem between the fax control PWB and main PWB Communication between the fax control PWB and the main PWB of the machine cannot be performed normally. |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective PWB. Replace the fax control PWB or main PWB and check for correct operation. |
| Error code: | C0320 |
| Description: | Power CPU communication problem A communication error is detected 10 times in succession. |
| Causes: | Defective engine PWB. |
| Remedy: | Replace the engine PWB and check for correct operation. |
| Error code: | C0420 |
| Description: | Side feeder* communication error • A communication error from side feeder is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective side feeder main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC15 on the engine PWB and the connector YC3 on the side feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective side feeder main PWB. Replace the side feeder main PWB. |
| Error code: | C0440 |
| Description: | Document finisher communication problem • A communication error from document finisher is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective finisher main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC14 on the engine PWB and YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective finisher main PWB. Replace the finisher main PWB. |
| Error code: | C0450 |
| Description: | Mailbox communication problem • Communication errors from the communication microcomputer on the main PCB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession. |
| Causes: | Poor contact in the connector terminals. Defective main PCB. Defective mailbox main PCB. |
| Remedy: | Check the connection of connectors YC3 on the main PCB and CN1 on the mailbox main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB and check for correct operation. Replace the mailbox main PCB and check for correct operation. |
| Error code: | C0470 |
| Description: | Switchback unit communication problem • Communication errors from the communication microcomputer on the main PCB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession. |
| Causes: | Poor contact in the connector terminals. Defective main PCB. Defective switchback unit main PCB. |
| Remedy: | Check the connection of connectors YC3 on the main PCB and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB and check for correct operation. Replace the switchback unit main PCB and check for correct operation. |
| Error code: | C0610 |
| Description: | Lens drive problem |
| Causes: | Defective main PWB. |
| Remedy: | Replace the main PWB and check for correct operation. |
| Error code: | C0630 |
| Description: | DMA error |
| Causes: | DMA transmission of the image data does not finish within the certain time. |
| Remedy: | 1 Checking the connection 0 0 2 Checking the connection 0 0 3 Replacing the wire The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • DPCIS - DP relay PWB • DP relay PWB - Main PWB Wiring diagram 4 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. Detaching and reattaching the DP relay PWB 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0640 |
| Description: | Hard Disk error |
| Causes: | The HDD cannot be accessed properly. |
| Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0820 |
| Description: | Fax control PWB CG ROM checksum error (optional fax) A checksum error occurred with the CG ROM data of the fax control PWB. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0830 |
| Description: | FAX PWB flash program area checksum error |
| Causes: | The program stored in the flash memory on the FAX PWB is broken so it cannot perform. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 2 Checking the FAX PWB The FAX PWB is not properly connected. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0860 |
| Description: | Fax control PWB software switch checksum error (optional fax) A checksum error occurred with the software switch value of the fax control PWB. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0870 |
| Description: | PC FAX Image data transmission error |
| Causes: | Data was not properly transmitted even if the specified times of retry were made when the large volume data is transmitted between the FAX PWB and the main PWB. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 3 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 6 Executing U024 The data stored in the SSD is faulty. Execute U024 [SSD Format]. Executing U024 |
| Error code: | C0880 |
| Description: | Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0890 |
| Description: | Fax control PWB CG FONT archive problem (optional fax) When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0900 |
| Description: | 3rd drawer lift problem |
| Causes: | Fax software version or main software is earlier. |
| Remedy: | Check the version of the fax software and the main software, upgrade the version to the compatible software. |
| Error code: | C1010 |
| Description: | Lift motor 1 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1020 |
| Description: | Lift motor 2 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1030 |
| Description: | Lift motor 3 error • When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on. This error is detected four times successively. • During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 3. Defective lift motor 3. Poor contact of lift motor 3 connector terminals. Defective lift limit switch 3. Poor contact of lift limit switch 3 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 3. Replace lift motor 3. Defective lift motor 3. Check for continuity across the coil. If none, replace lift motor 3. Poor contact of lift motor 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 3. Run maintenance item U031 and turn lift limit switch 3 on and off manually. Replace lift limit switch 3 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB |
| Error code: | C1040 |
| Description: | Lift motor 4 error • When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on. This error is detected four times successively. • During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 4. Defective lift motor 4. Poor contact of lift motor 4 connector terminals. Defective lift limit switch 4. Poor contact of lift limit switch 4 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 4. Replace lift motor 4. Defective lift motor 4. Check for continuity across the coil. If none, replace lift motor 4. Poor contact of lift motor 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 4. Run maintenance item U031 and turn lift limit switch 4 on and off manually. Replace lift limit switch 4 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB. |
| Error code: | C1100 |
| Description: | PF lift motor 1 error |
| Causes: | [The right cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because one of the phenomena below. 1. PF lift sensor 1 does not turn on when passing 23s while PF lift motor 1 turns on for the first time after inserting the cassette. 2. PF lift sensor 1 does not turn on when passing 2s while PF lift motor 1 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 1 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 1 - PF main PWB Wiring diagram 4 Checking PF lift motor 1 PF lift motor 1 is faulty. Replace PF lift motor 1. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift sensor 1 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 1 is not properly attached or faulty. Reattach PF lift sensor 1. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1110 |
| Description: | PF lift motor 2 error |
| Causes: | [The left cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because of one of the phenomena below. 1. PF lift sensor 2 does not turn on when passing 23s while PF lift motor 2 turns on for the first time after inserting the cassette. 2. PF lift sensor 2 does not turn on when passing 2s while PF lift motor 2 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 2 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 2 - PF main PWB Wiring diagram 4 Replacing PF lift motor 2 PF lift motor 2 is faulty. Replace PF lift motor 2. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •PF lift sensor 2 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 2 is not properly attached or faulty. Reattach PF lift sensor 2. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1120 |
| Description: | PF left lift position problem (optional 3000-sheet paper feeder) Level switch 1 does not turn on within 30 s of PF lift motor 2 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 1. Defective PF lift motor 2. The PF left lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 1. Check if YC5-4 on the PF main PWB goes low when level switch 1 is turned off. If not, replace PF lift switch 1. Defective PF lift motor 1. Check for continuity across the coil. If none, replace PF lift motor 1. The PF left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1130 |
| Description: | PF right lift position problem (optional 3000-sheet paper feeder) Level switch 2 does not turn on within 30 s of PF lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 2. Defective PF lift motor 1. The PF right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 2. Check if YC5-7 on the PF main PWB goes low when level switch 2 is turned off. If not, replace PF lift switch 2. Defective PF lift motor 2. Check for continuity across the coil. If none, replace PF lift motor 2. The PF right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C2000 |
| Description: | Drive motor problem Stable OFF is detected for 1 s continuously after drive motor stability. The drive motor is not stabilized in 6 s since the motor is activated. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective drive motor. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective drive motor. Replace the drive motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C2500 |
| Description: | Feed motor error |
| Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
| Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
| Error code: | C2600 |
| Description: | PF feed motor error |
| Causes: | The ready signal is not at the L level (stable rotation) after passing 1s since the PF feed motor drive started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected, or it is faulty. Execute U247 [2PF] or [LCF] > [Motor On] to check the paper feed operation. If the PF feed motor does not operate properly, reconnect the connector of the motor. Check if the PF feed roller and the drive gears rotate smoothly and have no excessive load, apply the grease (EM-50LP, Part no.: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF PWB • PF PWB - Engine PWB (Drawer connector between the paper feeder and the main unit) Service Manual - Section 8 `PWBs` 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF Drive Unit 4 Firmware upgrade The engine firmware or the PF firmware is faulty. Upgrade the engine firmware and the PF firmware to the latest version. Firmware Update 5 Replacing the PF PWB The PF PWB is faulty. Replace the PF PWB. Detaching and reattaching the PF PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C3100 |
| Description: | Carriage error |
| Causes: | When turning the power on or finishing originals scan through the scanner, the alignment of the home position sensor (turning on / off the sensor) fails and the error is detected. Then, the error is detected twice continuously even the initial operation is executed. |
| Remedy: | 1 Unlocking the scanner mirror frame The scanner mirror frame is not unlocked. Unlock the scanner mirror frame (lamp unit assy). Unlocking the scanner mirror frame 2 Checking the scanner movement A load is applied to the scanner movement. Check the operation of the lamp by U073 or manually moving it. If there is an excess load, check if there are any foreign objects on the optical wire or optical wire drum and clean it. After that, apply grease on the scanner rail. Detaching and reattaching the scanner wires 3 Checking the scanner wires The scanner wires are dirty or come off. Clean and reattach the scanner wires. Detaching and reattaching the scanner wires 4 Checking the scanner motor The scanner motor is faulty. Reattach the scanner motor and reconnect the connector. If not repaired, replace it. 5 Checking the belt tension of the scanner motor A load is applied to the scanner movement since the belt tension is improper. Adjust the scanner motor belt tension properly. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Scanner motor - Engine PWB Wiring diagram 7 Checking the home position sensor The home position sensor is not properly attached. Reattach the home position sensor. 8 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Home position sensor - Engine PWB Wiring diagram 9 Replacing the home position sensor The home position sensor is faulty. Replace the home position sensor. 10 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3200 |
| Description: | LED lamp startup error |
| Causes: | The white reference data acquired by lighting the LED lamp at the initial operation does not reach the specified value. Or, the light amount detected by the CCD PWB is not enough. (2 or more LED lamps do not light. The light does not reach the CCD PWB due to condensation.) |
| Remedy: | 1 Checking the LED lamp The LED lamp does not light. Execute U061 [CCD] and check if the LED lamp is lit. If not, replace the lamp unit. After that, execute U411 [Table(ChartA)]. Detaching and reattaching the lamp unit 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB • LED PWB - CCD PWB Wiring diagram 3 Checking the mirror The mirror or lens is frosted due to condensation. Clean the mirrors. If the condensation at the scanner section is resolved naturally by opening the document processor or the platen cover, turn the power switch off and on. 4 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3300 |
| Description: | CCD AGC error (For the internal count) |
| Causes: | Brightness of the LED lamp is darker while one of the LED lamp does not turn on or brighter than expected when processing the AGC for the CCD lamp. |
| Remedy: | 1 Checking the LED lamp The LED lamp is faulty. Check if the LED lamp lights by executing U061 [CCD]. If it does not light, replace the lamp unit and execute U411 [Table (ChartA) ]. Detaching and reattaching the lamp unit 2 Cleaning the backside of the contact glass The white reference sheet is dirty. Clean the white reference sheet at the backside of the contact glass. Detaching and reattaching the contact glass 3 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is peeled off, deformed or the FFC is broken, replace the FFC. • LED PWB - CCD PWB • CCD PWB - Engine PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 5 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4000 |
| Description: | Polygon motor synchronization problem • The revolution does not reach the stable speed within 20 s of the START signal. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4010 |
| Description: | Polygon motor steady-state problem • The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4200 |
| Description: | BD steady-state problem • ASIC of the main PWB detects a BD error A for 4000 ms after the polygon motor rotation has been stabilized. |
| Causes: | Defective laser diode. Defective polygon motor. Defective main PWB. Poor contact in connector terminals. |
| Remedy: | Defective laser diode. Replace the laser scanner unit. Defective polygon motor. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. Poor contact in connector terminals. Check the connection of connector YC8 on the main PWB and the continuity across the connector terminals. Repair or replace if necessary. |
| Error code: | C5300 |
| Description: | Cleaning lamp broken detection • The current at the correct level is not detected when ASIC (U8) on the engine controller PCB generates the signal to activate the cleaning lamp. |
| Causes: | Defective engine controller PCB. Defective drum unit (cleaning lamp or drum PCB). Defective harness between engine controller PCB and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the drum unit. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C6000 |
| Description: | IH heating error 1 |
| Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6020 |
| Description: | Fuser center thermistor high temperature error |
| Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6050 |
| Description: | Fuser center thermistor low temperature error |
| Causes: | The fuser center thermistor detects less than 100°C / 212°F for 1s after warm-up, or during print or standby. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 11 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit |
| Error code: | C6400 |
| Description: | Zero-cross signal error • The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s. |
| Causes: | Poor contact in the connector terminals. Defective DC power source PWB. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and YC6 on the DC power source PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective DC power source PWB. Check if the zero-crossing signal is output from YC6-3 on the DC power source PWB. If not, replace the DC power source PCB. Defective engine PWB. Replace the engine PWB if C6400 is detected while YC6-3 on the DC power source PWB outputs the zero-crossing signal. |
| Error code: | C6410 |
| Description: | Fuser unit type mismatch error |
| Causes: | "Unit Identification" code in the EEPROM of the fuser unit does not match the main unit. The fuser unit for other model is installed. |
| Remedy: | 1 Replacing the fuser unit The fuser unit for other models is installed. Install the fuser unit for the applicable models. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB Wiring diagram 5 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6420 |
| Description: | Fuser unit fuse cut problem The fuse cannot be cut, When replacing the fuser unit, the fuse cannot be cut in 3 s after the fuse cut signal is turned on. |
| Causes: | Poor contact in the connector terminals. Fuser unit connector inserted incorrectly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC1 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. |
| Error code: | C7300 |
| Description: | Toner hopper problem • During toner replenishment after toner empty has been detected, toner empty could not be cleared in 3 times of 360 s. |
| Causes: | Defective toner level detection sensor. Poor contact in the toner level detection sensor connector terminals. |
| Remedy: | Defective toner level detection sensor. Replace the toner level detection sensor. Poor contact in the toner level detection sensor connector terminals. Check the connection of connectors YC2 and YC5 on the deck PWB and YC3 on the engine PWB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Error code: | C7400 |
| Description: | Developing unit connector insertion problem Absence of the developing unit is detected. |
| Causes: | Developing unit connector inserted incorrectly. Defective developing unit connector. |
| Remedy: | Developing unit connector inserted incorrectly. Reinsert the developing unit connector if necessary. Defective developing unit connector. Replace the developing unit. |
| Error code: | C7410 |
| Description: | Drum unit connector insertion problem Absence of the drum unit is detected. |
| Causes: | Drum unit connector inserted incorrectly. Defective drum unit connector. |
| Remedy: | Drum unit connector inserted incorrectly. Reinsert the drum unit connector if necessary. Defective drum unit connector. Replace the drum unit. |
| Error code: | C7450 |
| Description: | Image formation unit fuse cut problem • The input voltage is above 4.5 V. |
| Causes: | Image formation unit connector inserted incorrectly. Defective image formation unit connector. |
| Remedy: | Reinsert the image formation unit connector if necessary. Replace the image formation unit. |
| Error code: | C7800 |
| Description: | Outer thermistor broken (For the internal count) |
| Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7810 |
| Description: | Short-circuited external thermistor • The thermistor input value is 0.5 V or less. |
| Causes: | Poor contact in the connector terminals. Defective humidity sensor. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC13 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective humidity sensor. Replace the humidity sensor. Defective engine PWB. Replace the engine PWB. |
| Error code: | C8010 |
| Description: | Punch motor error 1 Object: 4000-sheet finisher + Punch unit |
| Causes: | 1. The punch home position sensor does not turn on when passing 200ms after driving the punch motor. 2. The pulse plate does not count the specified pulse when passing 300ms after the punch operation starts. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • Punch home position sensor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. 5 Checking the punch home position sensor The punch home position sensor is not properly attached or faulty. Execute U241 [Punch] > [Punch HP]. If the PH home position sensor does not properly operate, reattach it. If not repaired, replace the sensor. Executing U241 6 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 7 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8030 |
| Description: | Punch motor error 3 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position detection does not turn off within 50ms when initializing the home position. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8140 |
| Description: | Main tray error 1 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8170 |
| Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
| Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
| Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8180 |
| Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
| Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
| Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8190 |
| Description: | DF side registration motor 2 error 1 Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while executing the operation of returning to the home position. |
| Remedy: | 1 Checking the rear DF side registration guide The rear DF side registration guide is not assembled properly. If the rear DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear DF side registration guide drive components The rear DF side registration guide drive parts are not properly attached or faulty. Reattach the rear DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 2 - DF main PWB • DF side registration sensor 2 - DF main PWB 4 Replacing DF side registration motor 2 DF side registration motor 2 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking DF side registration sensor 2 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8210 |
| Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8220 |
| Description: | Document finisher* front clincher problem • During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position. JAM90 is indicated the first time this problem occurs. If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher. • When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms. |
| Causes: | Loose connection of the front clincher motor connector. Malfunction of the front clincher motor. Malfunction of the front clincher home position sensor. Loose connection of the front clincher home position sensor connector. Defective finisher main PWB. |
| Remedy: | Loose connection of the front clincher motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Malfunction of the front clincher motor. Replace the front clincher motor and check for correct operation. Malfunction of the front clincher home position sensor. Replace the front clincher home position sensor and check for correct operation. Loose connection of the front clincher home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8300 |
| Description: | Main program error / Folding unit communication error Object: 4000-sheet finisher + Folding unit |
| Causes: | The main program of the folding unit is faulty when turning the power on. The communication error appears 10 times continuously after finishing the folding unit firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the BF firmware and the DF firmware to the latest version. Firmware Update 3 Checking the BF set switch The BF set switch is not properly attached. Reattach the BF set switch. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 5 Replacing the BF set switch The BF set switch is faulty. Execute U241 [Booklet] > [Set]. If the BF set switch does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8310 |
| Description: | BF side registration motor 2 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 2 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the upper BF side registration guide The upper BF side registration guide is not assembled properly. If the upper BF side registration guide is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the upper BF side registration guide drive components The upper BF side registration guide drive parts are not properly attached or faulty. Reattach the upper BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 2 - BF main PWB • BF side registration sensor 2 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 2 BF side registration motor 2 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 2 BF side registration sensor 2 is not properly attached or faulty. Reattach BF side registration sensor 2 and execute U241 [Booklet] > [Width Down HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8320 |
| Description: | BF adjustment motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | At the initialization, turning on of the BF adjustment sensor is not detected after 2.5s passes. |
| Remedy: | 1 Checking the BF shift belt The BF shift belt is not assembled properly. If the BF shift belt is not operated manually, repair the part that restricts the operation. 2 Checking the BF shift belt drive components The BF shift belt drive parts are not properly attached or faulty. Reattach the BF shift belt drive parts. Reattach it if the belt comes off. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF adjustment motor 1, 2 - BF main PWB • BF adjustment sensor 1, 2 - BF main PWB Wiring diagram 4 Replacing BF adjustment motor 1, 2 BF adjustment motor 1 or 2 is faulty. Execute U240 [Booklet] > [Bundle Down] or [Bundle Up]. If BF adjustment motor 1 or 2 does not properly operate, replace them. Executing U240 5 Checking BF adjustment sensor 1, 2 BF adjustment sensor 1 or 2 is not properly attached or faulty. Reattach BF adjustment sensor 1 or 2 and execute U241 [Booklet] > [Width Down HP] or [Bundle Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8330 |
| Description: | BF blade motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The BF blade sensor does not turn on after passing 3s during the initial operation. |
| Remedy: | 1 Checking the BF blade The BF blade is not assembled properly. If the BF blade is not operated manually, repair the part that restricts the operation. 2 Checking the BF blade drive components The BF blade drive parts are not properly attached or faulty. Reattach the BF blade drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF blade motor - BF main PWB • BF blade sensor - BF main PWB Wiring diagram 4 Replacing the BF blade motor The BF blade motor is faulty. Execute U240 [Booklet] > [Blade]. If the BF blade motor does not properly operate, replace it. Executing U240 5 Checking the BF blade sensor The BF blade sensor is faulty. Reattach the BF blade sensor and reinsert the connector. Next, execute U241 [Booklet] > [Blade HP]. If it does not properly operate, replace the sensor. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8340 |
| Description: | BF staple motor error 1 Object: 4000-sheet finisher + Folding unit |
| Causes: | J7600 (BF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the BF staple unit The BF staple unit is not assembled properly. If the BF staple unit is not operated manually, repair the part that restricts the operation. 2 Checking the BF staple unit drive components The BF staple unit drive parts are not properly attached or faulty. Reattach the BF staple unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF staple unit - BF main PWB Wiring diagram 4 Replacing the BF staple motor The BF staple motor is faulty. Execute U240 [Booklet] > [Staple]. If the BF staple motor does not properly operate, replace it. Executing U240 5 Replacing the BF staple unit The BF staple unit is faulty. Replace the BF staple unit. 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8350 |
| Description: | BF side registration motor 1 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 1 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the lower BF side registration guide The lower BF side registration guide is not assembled properly. If the lower BF side registration guide is not operated manually, repair the part that restricts the operation. 2 Checking the lower BF side registration guide drive components The lower BF side registration guide drive parts are not properly attached or faulty. Reattach the lower BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 1 - BF main PWB • BF side registration sensor 1 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 1 BF side registration motor 1 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 1 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 1 BF side registration sensor 1 is not properly attached or faulty. Reattach BF side registration sensor 1 and execute U241 [Booklet] > [Width Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8360 |
| Description: | BF main motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The lock-up signal was detected for 1s continuously during the motor operation. |
| Remedy: | 1 Checking the BF conveying roller The BF conveying roller is not assembled properly. If the BF conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the BF conveying roller drive parts The BF conveying roller drive parts are not properly attached or faulty. Reattach the BF conveying roller drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main motor - BF main PWB Wiring diagram 4 Replacing the BF main motor The BF main motor is faulty. Execute U240 [Booklet] > [Folding]. If the BF main motor does not properly operate, replace it. Executing U240 5 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8370 |
| Description: | BF staple motor error 2 Object: 4000-sheet finisher + Folding unit |
| Causes: | J7600 (BF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The lock-up detection signal is outputs for 500ms continuously during the motor operation.) |
| Remedy: | 1 Checking the BF staple unit The BF staple unit is not assembled properly. If the BF staple unit is not operated manually, repair the part that restricts the operation. 2 Checking the BF staple unit drive components The BF staple unit drive parts are not properly attached or faulty. Reattach the BF staple unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF staple unit - BF main PWB Wiring diagram 4 Replacing the BF staple motor The BF staple motor is faulty. Execute U240 [Booklet] > [Staple]. If the BF staple motor does not properly operate, replace it. Executing U240 5 Replacing the BF staple unit The BF staple unit is faulty. Replace the BF staple unit. 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8380 |
| Description: | BF eject pressure release motor error Object: 4000-sheet finisher with the folding unit |
| Causes: | Operation is not complete when passing 3s after starting up the BF eject pressure release motor |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • The BF eject pressure release motor - DF PWB • The BF eject pressure release HP sensor - DF PWB 2 Repacing the BF eject pressure release motor The BF eject pressure release motor is faulty Execute U240 [Booklet] > [Staple]. If the BF staple motor does not operate properly, replace it. 3 Replacing the BF eject pressure release HP sensor The BF eject pressure release HP sensor is faulty Replace the BF eject pressure release HP sensor 4 Replacing the BF PWB The BF PWB is faulty. Replace the BF PWB. |
| Error code: | C8390 |
| Description: | BF paddle motor error Object: 4000-sheet finisher with the folding unit |
| Causes: | Operation is not complete when passing 250ms after starting up the BF paddle motor |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. EBF eject pressure release motor - BF PWB EBF eject pressure release HP sensor - BF PWB 2 Replacing the BF paddle motor The BF paddle motor is faulty Execute U240 mBookletn > mPaddlen. Replace the BF paddle motor if it does not operate properly. 3 Replacing the BF paddle HP sensor The BF paddleHP sensor is faulty Replace the BF paddle HP sensor 4 Replacing the BF PWB The BF PWB is faulty. Replace the BF PWB. |
| Error code: | C8410 |
| Description: | Punch slide motor error 1 Object: 4000-sheet finisher + Punch unit |
| Causes: | The punch slide sensor does not turn on after the home position shifts 30mm. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch slide section is not shifted manually forwardbackward, repair the part that restricts the operation. 2 Checking the punch drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch slide motor - PH main PWB • Punch slide sensor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the PH slide motor The punch slide motor is faulty. Execute U240 [Motor] > [Punch Move]. If the punch slide motor does not properly operate, replace it. 5 Checking the punch slide sensor The punch slide sensor is not properly attached or faulty. Reattach the punch slide sensor. If not repaired, replace it. 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8420 |
| Description: | Punch slide motor error 2 Object: 4000-sheet finisher + Punch unit |
| Causes: | The paper edge cannot be detected even if shifting 30mm when detecting the paper edge. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch slide section is not shifted manually forwardbackward, repair the part that restricts the operation. 2 Checking the punch drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch slide motor - PH main PWB • PH paper edge sensor 1, 2 - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the PH slide motor The punch slide motor is faulty. Execute U240 [Motor] > [Punch Move]. If the punch slide motor does not properly operate, replace it. 5 Checking the PH paper edge sensor 1, 2 PH paper edge sensor 1 or 2 is not properly attached or faulty. Reattach PH paper edge sensor 1 or 2 and execute U241 [Punch] > [Edge Face1] or [Edge Face2]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8430 |
| Description: | Main program error (Punch unit) / Punch unit communication error Object: 4000-sheet finisher + Punch unit |
| Causes: | The main program of the punch unit is faulty when turning the power on. The communication error appears 10 times continuously after finishing the punch unit firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware and the DF firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PH main PWB - DF main PWB 4 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8440 |
| Description: | Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range. |
| Causes: | The paper entry sensor connector makes poor contact. Defective paper entry sensor. The optical path of the paper entry sensor is blocked by foreign matter. Defective finisher main PWB. |
| Remedy: | The paper entry sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective paper entry sensor. Replace the paper entry sensor and check for correct operation. The optical path of the paper entry sensor is blocked by foreign matter. Remove the foreign matter. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8450 |
| Description: | Booklet stitcher side punch sensor problem |
| Causes: | A problem is detected with the side punch sensor. |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | C8460 |
| Description: | EEPROM problem (optional document finisher) Reading from or writing to EEPROM cannot be performed. |
| Causes: | Defective EEPROM or finisher main PWB. |
| Remedy: | Replace the finisher main PWB and check for correct operation. |
| Error code: | C8470 |
| Description: | Booklet stitcher punch dust sensor problem |
| Causes: | A problem is detected with the punch dust sensor. |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | C8480 |
| Description: | Booklet stitcher broken punch power source wire problem |
| Causes: | A broken punch power source wire problem is detected. |
| Remedy: | See the booklet stitcher service manual. |
| Error code: | C8500 |
| Description: | Main program error (Mail Box) / Mail Box communication error Object: 4000-sheet finisher + Mail box |
| Causes: | The main program of the mail box is faulty when turning the power on. The communication error appears 10 times continuously after finishing the mail box firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the MB firmware and the DF firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB main PWB - DF main PWB 4 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
