Kyocera KM-C2525E
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Скорость печати
A4
25
Цветность печати
цветная
Общие характеристики |
|
---|---|
Цветность печати |
цветная |
Тип |
лазерный/светодиодный |
Технология печати |
лазерная |
Размещение |
напольный |
Макс. формат |
A3 |
Копир |
|
Тип устройства |
МФУ |
Сканер |
|
Телефон |
|
Факс |
|
Печать фотографий |
|
Принтер |
|
Время разогрева |
45 |
Печать без полей |
|
Пигментные чернила |
|
Прямая печать |
|
Двусторонняя печать |
|
Количество цветов |
4 |
Макс, разрешение для ч/б печати |
|
По X | 600 |
По Y | 600 |
Скорость ч/б печати |
|
A3 | 13 |
A4 | 25 |
Время выхода первого отпечатка |
|
Ч/б | 5,9 |
Цветн, | 7,9 |
Копир |
|
Макс, количество копий за цикл |
999 |
Время выхода первой копии |
7,9 |
Шаг масштабирования |
0,01 |
Значение масштаба |
|
Максимальное | 4 |
Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
По Y | 600 |
По X | 600 |
Сканер |
|
Слайд-адаптер |
|
Стандарт TWAIN |
|
Макс. формат оригинала |
A3 |
Тип сканера |
планшетный/протяжный |
Макс, размер сканирования |
|
По X | 297 |
По Y | 420 |
Разрешение сканера |
|
По Х | 600 |
Скорость сканирования |
|
Цветн, | 32 |
Ч/б | 32 |
Расходные материалы |
|
Количество картриджей |
4 |
Ресурс ч/б картриджа/тонера |
15 000 |
Ресурс цветного картриджа/тонера |
7 000 |
Печать на: |
|
Глянцевой бумаге | |
Пленках | |
Конвертах | |
Карточках | |
Матовой бумаге | |
Этикетках | |
CD/DVD | |
Фотобумаге | |
Рулоне | |
Плотность бумаги |
|
Минимальная | 60 |
Максимальная | 220 |
Факс |
|
Цветной |
|
Телефон |
|
Проводная трубка |
|
Спикерфон |
|
Стандарт DECT |
|
Автоответчик |
|
Caller ID |
|
АОН |
|
Беспроводная трубка |
|
Шрифты и языки управления |
|
Языки управления |
|
PCL 6 | |
PostScript | |
PostScript 3 | |
PCL 5c | |
PCL 5e | |
PPDS | |
PostScript 2 | |
Количество установленных шрифтов |
|
PostScript | 136 |
PCL | 80 |
Лотки |
|
Подача бумаги |
|
Стандартная | 1 100 |
Максимальная | 4 100 |
Вывод бумаги |
|
Стандартный | 250 |
Финишер |
|
Сортер |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Степлер |
|
Брошюровщик |
|
Интерфейсы |
|
Версия USB |
2,0 |
USB |
|
Ethernet (RJ-45) |
|
LPT |
|
Bluetooth |
|
Wi-Fi |
|
Инфракрасный порт |
|
FireWire (IEEE 1394) |
|
Устройство для чтения карт памяти |
|
RS-232 |
|
Память/Процессор |
|
Емкость жесткого диска |
40 |
Объем памяти |
768 |
Макс, объем памяти |
768 |
Процессор |
PowerPC 750FL |
Частота процессора |
600 |
Дополнительная информация |
|
Поддержка ОС |
|
Windows | |
Linux | |
DOS | |
Mac OS | |
Потребляемая мощность |
|
В режиме ожидания | 230 |
При работе | 700 |
Уровень шума |
|
В режиме ожидания | 53,3 |
При работе | 65,5 |
Габариты |
|
Глубина |
660 |
Высота |
745 |
Ширина |
605 |
Вес |
98 |
Модули
OPERATION UNIT
Driving Unit II (25/25ppm) (32/25ppm) (32/32ppm)
Optical Unit II
ELECTRICAL COMPONENTS III
Options I
Frames II
Table Bypass
TRANSFER UNIT
Driving Unit I (25/25ppm) (32/25ppm) (32/32ppm)
MPT Bypass Assy
Options II
Cooling Unit
Electrical Components II
Developer unit
Electrical Components I
COVERS
Imaging Unit
Paper Conveying III
Paper Cassette I
Primary Unit
Optical Unit I
Paper Cassette II
Paper Conveying I
Controller Box
Paper Conveying II
Paper exit
Driving Unit I (40/35ppm)
Driving Unit II (40/35ppm)
MPT Assy
FUSER UNIT
Frames I
Детали Cooling Unit
Деталь: | GROUND PLATE LCD A |
Парткод: | 2BJ04220 |
Деталь: | GROUND PLATE LCD C |
Парткод: | 2BJ04240 |
Деталь: | KEY OPERATION 10 |
Парткод: | 2BJ25020 |
Деталь: | BARRIER TABLET |
Парткод: | 2BJ25240 |
Деталь: | VOLUME OPE UNIT |
Парткод: | 2BJ25250 |
Деталь: | SPONGE LCD A |
Парткод: | 2BJ25270 |
Деталь: | SPONGE LCD B |
Парткод: | 2BJ25280 |
Деталь: | SHEET LCD A |
Парткод: | 2BJ25400 |
Деталь: | KEY FUNCTION J |
Парткод: | 2FB24150 |
Деталь: | LCD PWB |
Парткод: | 2FB28190 |
Деталь: | KEY STOP |
Парткод: | 302BJ25041 |
Деталь: | KEY RESET |
Парткод: | 302BJ25051 |
Деталь: | KEY SAVER |
Парткод: | 302BJ25061 |
Деталь: | KEY INTERRUPT |
Парткод: | 302BJ25071 |
Деталь: | KEY CONTROL |
Парткод: | 302BJ25081 |
Деталь: | KEY POWER SUPPLY |
Парткод: | 302FB24061 |
Деталь: | KEY PRINT |
Парткод: | 302FB24200 |
Деталь: | RETAINER LCD |
Парткод: | 302FB24250 |
Деталь: | TABLET OPERATION |
Парткод: | 302FB25190 |
Деталь: | PRINTED W.BOARD PANEL A |
Парткод: | 302FZ01080 |
Деталь: | PRINTED W.BOARD PANEL B |
Парткод: | 302FZ01090 |
Деталь: | COVER OPERATION |
Парткод: | 302FZ05010 |
Деталь: | KEY INIT |
Парткод: | 302FZ05020 |
Деталь: | LEFT KEY FUNCTION |
Парткод: | 302FZ05030 |
Деталь: | LENS LED FUNCTION |
Парткод: | 302FZ05040 |
Деталь: | KEY COLOR |
Парткод: | 302FZ05050 |
Деталь: | SHEET TABLET |
Парткод: | 302FZ05060 |
Деталь: | RIGHT DUST SHIELD |
Парткод: | 302FZ05070 |
Деталь: | SHEET OPERATION PWB |
Парткод: | 302FZ05080 |
Деталь: | CENTER DUST SHIELD |
Парткод: | 302FZ05090 |
Деталь: | LEFT DUST SHIELD |
Парткод: | 302FZ05100 |
Деталь: | SHIELD BASE OPERATION |
Парткод: | 302FZ05110 |
Деталь: | SPRING EARTH KEYTOP |
Парткод: | 302FZ05190 |
Деталь: | LENS LED FUNCTION KEY |
Парткод: | 302FZ05200 |
Деталь: | LABEL START E |
Парткод: | 302FZ05250 |
Деталь: | LABEL START TW |
Парткод: | 302FZ05410 |
Деталь: | LABEL COLOR E |
Парткод: | 302FZ05260 |
Деталь: | LABEL COLOR TW |
Парткод: | 302FZ05420 |
Деталь: | LABEL APPLICATION E |
Парткод: | 302FZ05270 |
Деталь: | LABEL APPLICATION TW |
Парткод: | 302FZ05430 |
Деталь: | LABEL SYSTEM MENU E |
Парткод: | 302FZ05280 |
Деталь: | LABEL SYSTEM MENU TW |
Парткод: | 302FZ05440 |
Деталь: | LABEL FUNCTION E |
Парткод: | 302FZ05290 |
Деталь: | LABEL FUNCTION TW |
Парткод: | 302FZ05450 |
Деталь: | LABEL OPE COVER E |
Парткод: | 302FZ05300 |
Деталь: | LABEL OPE COVER TW |
Парткод: | 302FZ05460 |
Деталь: | SPACER START KEY |
Парткод: | 302FZ05320 |
Деталь: | SPACER COVER OPE A |
Парткод: | 302FZ05400 |
Деталь: | WIRE LCD |
Парткод: | 302FZ46600 |
Деталь: | LENS POWER LED |
Парткод: | 302GR05280 |
Деталь: | ACCESS.SPACER |
Парткод: | 7YZM510006++H01 |
Деталь: | THERMAL SHEET |
Парткод: | 7ZS15063001+H01 |
Деталь: | HINGE OPERATION L |
Парткод: | 302GR05030 |
Деталь: | HINGE OPERATION R |
Парткод: | 302GR05040 |
Деталь: | BASE OPERATION |
Парткод: | 302GR05050 |
Деталь: | MOUNT HANDLE OPE |
Парткод: | 302GR05060 |
Деталь: | HANDLE OPE |
Парткод: | 302GR05070 |
Деталь: | CUSHION HANDLE A |
Парткод: | 302GR05080 |
Деталь: | BUSH PIN OPE |
Парткод: | 302GR05090 |
Деталь: | SPRING HINGE OPE L |
Парткод: | 302GR05100 |
Деталь: | SPRING HINGE OPE R |
Парткод: | 302GR05110 |
Деталь: | MOUNT SLIDE |
Парткод: | 302GR05120 |
Деталь: | PIN OPERATION |
Парткод: | 302GR05130 |
Деталь: | GROUND PLATE OPE A |
Парткод: | 302GR05320 |
Деталь: | SPRING MOUNT HANDLE A |
Парткод: | 302GR05350 |
Деталь: | GROUND PLATE OPE B |
Парткод: | 302GR05510 |
Деталь: | GROUND PLATE OPE C |
Парткод: | 302GR05520 |
Деталь: | FILM OPERATION A |
Парткод: | 302GR05650 |
Деталь: | GROUND PLATE DECK UNIT |
Парткод: | 302FB09320 |
Деталь: | SHEET OPERATION WIRE |
Парткод: | 302FZ05550 |
Деталь: | COVER OPERATION B |
Парткод: | 302FZ05240 |
Деталь: | SHEET OPE PROTECT B |
Парткод: | 302GR04470 |
Деталь: | FILM PROTECT |
Парткод: | 302GR04480 |
Деталь: | PARTS OPERATION UPPER E ASSY |
Парткод: | 302FZ93201 |
Деталь: | PARTS OPERATION UPPER TW ASSY |
Парткод: | 302FZ93520 |
Деталь: | GEAR Z38R DSK |
Парткод: | 302FZ31520 |
Деталь: | PULLEY 26 FEED |
Парткод: | 302FZ31730 |
Деталь: | BELT FEED DRIVE |
Парткод: | 302FZ31260 |
Деталь: | WIRE JOINT |
Парткод: | 302FZ46020 |
Деталь: | BUSH 6 |
Парткод: | 2BG22960 |
Деталь: | BUSH 8 |
Парткод: | 2BG22980 |
Деталь: | MOTOR FEED |
Парткод: | 302FZ31020 |
Деталь: | PLATE FEED DRIVE |
Парткод: | 302FZ31120 |
Деталь: | HOLDER FEED DRIVE |
Парткод: | 302FZ31130 |
Деталь: | HOLDER CLUTCH |
Парткод: | 302FZ31170 |
Деталь: | SHAFT FEED DRIVE |
Парткод: | 302FZ31200 |
Деталь: | SHAFT FEED 2 DRIVE |
Парткод: | 302FZ31210 |
Деталь: | SHAFT LSU DRIVE |
Парткод: | 302FZ31240 |
Деталь: | GEAR Z81L-Z22R |
Парткод: | 302FZ31420 |
Деталь: | GEAR Z42L |
Парткод: | 302FZ31430 |
Деталь: | GEAR Z14R LSU |
Парткод: | 302FZ31440 |
Деталь: | GEAR Z36L-Z22R REG |
Парткод: | 302FZ31450 |
Деталь: | GEAR Z52L LSU |
Парткод: | 302FZ31460 |
Деталь: | GEAR Z33R-Z23R CL |
Парткод: | 302FZ31470 |
Деталь: | GEAR Z33R-Z23R FEED |
Парткод: | 302FZ31480 |
Деталь: | GEAR Z28L |
Парткод: | 302FZ31490 |
Деталь: | GEAR Z32L-Z26R FEED CL |
Парткод: | 302FZ31500 |
Деталь: | GEAR Z26R-Z23L FEED CL |
Парткод: | 302FZ31510 |
Деталь: | GEAR Z32L |
Парткод: | 302FZ31530 |
Деталь: | GEAR Z35L CL |
Парткод: | 302FZ31590 |
Деталь: | GEAR Z28R |
Парткод: | 302FZ31600 |
Деталь: | PIN DRIVE FEED |
Парткод: | 302FZ31740 |
Деталь: | GEAR Z25R JOINT |
Парткод: | 302FZ31800 |
Деталь: | CLUTCH REGIST 8 |
Парткод: | 302FZ31810 |
Деталь: | CLUTCH FEED 6 |
Парткод: | 302FZ31820 |
Деталь: | STUD SCREW 435 |
Парткод: | 302FZ31840 |
Деталь: | COUPLING PAPER FEED |
Парткод: | 302FZ32070 |
Деталь: | PLATE EARTH FEED |
Парткод: | 302FZ39720 |
Деталь: | WIRE PRE FEED |
Парткод: | 302FZ46100 |
Деталь: | PARTS,PWB FEED ASSY,SP |
Парткод: | 302FZ94681 |
Деталь: | CUT WASHER |
Парткод: | 5MVS665KB001 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | CONNECTOR |
Парткод: | 7YCC08B2046+H02 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210006++H01 |
Деталь: | ACCESS.BAND |
Парткод: | 7YZM410001++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | WIRE TRANSFER |
Парткод: | 302FZ46050 |
Деталь: | COLLAR EJECT |
Парткод: | 3HL10170 |
Деталь: | COLLAR DU PULLEY |
Парткод: | 302FZ29140 |
Деталь: | WIRE EXIT MOT |
Парткод: | 302FZ46411 |
Деталь: | BUSHING 8 |
Парткод: | 2BC06510 |
Деталь: | STOPPER 5 |
Парткод: | 2BC06980 |
Деталь: | GEAR Z20L FUSER DRIVE |
Парткод: | 302FZ31570 |
Деталь: | GEAR Z46 FUSER |
Парткод: | 302FZ31580 |
Деталь: | JOINT GEAR EXIT |
Парткод: | 302FZ31671 |
Деталь: | PULLEY EXIT DRIVE |
Парткод: | 302FZ31680 |
Деталь: | GEAR EXIT Z20 |
Парткод: | 302FZ31690 |
Деталь: | GEAR EXIT Z63 Z21 |
Парткод: | 302FZ31700 |
Деталь: | PIN EXIT |
Парткод: | 302FZ31750 |
Деталь: | GEAR EXIT Z39Z26 |
Парткод: | 302FZ31760 |
Деталь: | GEAR EXIT Z30 JOINT |
Парткод: | 302FZ31770 |
Деталь: | GEAR EXIT Z48 |
Парткод: | 302FZ31780 |
Деталь: | SPRING EXIT 60 |
Парткод: | 302FZ31790 |
Деталь: | MOUNT FUSER DRIVE |
Парткод: | 302FZ31861 |
Деталь: | GEAR Z20 FUSER |
Парткод: | 302FZ31870 |
Деталь: | GEAR EXIT Z45Z22 |
Парткод: | 302FZ31910 |
Деталь: | GEAR Z30 FUSER |
Парткод: | 302FZ31920 |
Деталь: | GEAR Z65-Z29 FUSER |
Парткод: | 302FZ31930 |
Деталь: | PLATE FUSER DRIVE |
Парткод: | 302FZ32010 |
Деталь: | HOLDER FUSER CL |
Парткод: | 302FZ32021 |
Деталь: | SHAFT FUSER DRIVE |
Парткод: | 302FZ32030 |
Деталь: | CLUTCH FUSER 8 |
Парткод: | 302FZ32040 |
Деталь: | PARTS,MOTOR FUSER SP |
Парткод: | 302FZ94290 |
Деталь: | SW.MICRO |
Парткод: | 7SM010303+++H01 |
Деталь: | PARTS FEED DRIVE ASSY |
Парткод: | 302FZ93281 |
Деталь: | PARTS FUSER DRIVE ASSY |
Парткод: | 302FZ93270 |
Деталь: | PARTS CONTACT GLASS (M) ASSY |
Парткод: | 302GR93310 |
Деталь: | PARTS CONTACT GLASS (I) ASSY |
Парткод: | 302GR93320 |
Деталь: | PARTS CONTACT GLASS DP ASSY |
Парткод: | 302GR94380 |
Деталь: | MOUNT LSU RIGHT |
Парткод: | 302FZ02540 |
Деталь: | CUSHION,CONTACT GLASS |
Парткод: | 29812291 |
Деталь: | RETAINER MIRROR FRAME A |
Парткод: | 302GR17262 |
Деталь: | SPRING FRAME RETAINER |
Парткод: | 302GR17360 |
Деталь: | SHEET COVER ISU |
Парткод: | 302GR04430 |
Деталь: | SHEET BAND TUBE |
Парткод: | 302FZ03020 |
Деталь: | GROUND PLATE ISU OPE |
Парткод: | 302GR04360 |
Деталь: | COVER ISU RIGHT |
Парткод: | 302GR04210 |
Деталь: | COVER ISU LEFT |
Парткод: | 302GR04221 |
Деталь: | COVER ISU REAR |
Парткод: | 302GR04231 |
Деталь: | SEAL COVER ISU LEFT A |
Парткод: | 302GR17910 |
Деталь: | SEAL COVER ISU LEFT B |
Парткод: | 302GR17920 |
Деталь: | SEAL COVER ISU LEFT C |
Парткод: | 302GR17940 |
Деталь: | PLATE HOLDER ISU |
Парткод: | 302GR17670 |
Деталь: | PLATE SPRING ISU |
Парткод: | 302GR17680 |
Деталь: | PIN MOUNT LENS |
Парткод: | 302GR17811 |
Деталь: | WIRE CCD1 |
Парткод: | 302GR46010 |
Деталь: | LABEL,CAUTION CONTACT GLASS |
Парткод: | 2A105180 |
Деталь: | COVER ISU |
Парткод: | 302GR17560 |
Деталь: | PIN ISU |
Парткод: | 302GR17660 |
Деталь: | SHIELD GASKET |
Парткод: | 7ZGSTG151018H01 |
Деталь: | COVER ISU FRONT LOW |
Парткод: | 302GR04200 |
Деталь: | COVER TOTAL COUNTER |
Парткод: | 2FG04020 |
Деталь: | COVER RIGHT MID B |
Парткод: | 302FZ04081 |
Деталь: | COVER ISU FRONT TOP |
Парткод: | 302GR04240 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | JOINT TUBE |
Парткод: | 302FZ33090 |
Деталь: | SPRING LSU |
Парткод: | 302FZ20040 |
Деталь: | PIN LSU |
Парткод: | 302FZ20030 |
Деталь: | PARTS ISU ASSY |
Парткод: | 302FZ93470 |
Деталь: | PARTS LSU ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ93080 |
Деталь: | PARTS LSU ASSY (40/35ppm) |
Парткод: | 302JD93010 |
Деталь: | HOLDER RETAINER A |
Парткод: | 302GR17900 |
Деталь: | SEAL FRAME E |
Парткод: | 302FZ17050 |
Деталь: | COVER SCREW |
Парткод: | 302BG04560 |
Деталь: | PLATE HOLDER RAIL |
Парткод: | 302GR17790 |
Деталь: | SEAL RAIL SCANNER F |
Парткод: | 302GR17870 |
Деталь: | COVER RMB SUB |
Парткод: | 302FZ04650 |
Деталь: | SHIELD 5X1X30,GASKET |
Парткод: | 2A627240 |
Деталь: | PRINTED W.BOARD DIMM IPU U ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ01220 |
Деталь: | PARTS,PWB DIMM IPU U ASSY SP (40/35ppm) |
Парткод: | 302JD94060 |
Деталь: | PRINTED W.BOARD DIMM IPU E ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ01230 |
Деталь: | PARTS,PWB DIMM IPU E ASSY SP (40/35ppm) |
Парткод: | 302JD94070 |
Деталь: | PRINTED W.BOARD DIMM IPU TW ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ01340 |
Деталь: | MOUNT IPU |
Парткод: | 302FZ39030 |
Деталь: | BRACKET HDD LOWER |
Парткод: | 302FZ39090 |
Деталь: | WIRE HDD POWER |
Парткод: | 302FZ46300 |
Деталь: | WIRE HDD |
Парткод: | 302FZ46630 |
Деталь: | WIRE IPU ENGINE |
Парткод: | 302FZ46651 |
Деталь: | SCANNER NIC ASSY |
Парткод: | 303JR01011 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210002++H01 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210004++H01 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210006++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610016++H01 |
Деталь: | THERMAL SHEET |
Парткод: | 7ZS40405001+H01 |
Деталь: | SPRING HV2 TC |
Парткод: | 302FZ39620 |
Деталь: | SPRING HV2 SE |
Парткод: | 302FZ39630 |
Деталь: | PARTS,PWB IPU ASSY,SP (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ94052 |
Деталь: | PARTS,PWB IPU U ASSY SP (40/35ppm) |
Парткод: | 302JD94050 |
Деталь: | WIRE HVU 3 (40/35ppm) |
Парткод: | 302JD46030 |
Деталь: | WIRE HVU 3 (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ46130 |
Деталь: | WIRE PANNEL L |
Парткод: | 302FZ46612 |
Деталь: | PLATE EARTH ISU REAR |
Парткод: | 302FZ39770 |
Деталь: | BRACKET HDD |
Парткод: | 302FZ39040 |
Деталь: | DUCT IPU |
Парткод: | 302FZ39860 |
Деталь: | PARTS,FAN COOLING CONVEYING SP |
Парткод: | 302FZ94420 |
Деталь: | WIRE LSU FAN |
Парткод: | 302FZ46670 |
Деталь: | COVER REAR OP |
Парткод: | 302FZ04460 |
Деталь: | STORAGE DEVICE |
Парткод: | 7NH3M040G003H01 |
Деталь: | HOLDER HV2 TC |
Парткод: | 302FZ39610 |
Деталь: | HVU TRANSFER 2 |
Парткод: | 302FZ45051 |
Деталь: | (25/25ppm) (32/25ppm) (32/32ppm)PARTS,PWB HVU TRANSFER 2 ASSY SP |
Парткод: | 302JD94110 |
Деталь: | (40/35ppm)MEMORY MODULE |
Парткод: | 7NMDD256MJ41H01 |
Деталь: | MEMORY MODULE |
Парткод: | 7NMDD512MJ41H01 |
Деталь: | COVER,PLATEN |
Парткод: | 2A612800 |
Деталь: | MAT,ORIGINAL HOLDER |
Парткод: | 2A612810 |
Деталь: | HINGE,ORIGINAL HOLDER |
Парткод: | 2A612820 |
Деталь: | STOPPER RELEASE SWITCH |
Парткод: | 2C912630 |
Деталь: | ORIGINAL POCKET |
Парткод: | 60904280 |
Деталь: | SET,PLATEN COVER TYPE D (OPTION) |
Парткод: | 2CX82010 |
Деталь: | FRAME FUSER UNIT FRONT |
Парткод: | 302FZ02260 |
Деталь: | SPRING EARTH EXIT |
Парткод: | 302FZ02510 |
Деталь: | FRAME FUSER UNIT REAR |
Парткод: | 302FZ02270 |
Деталь: | PLATE EARTH FUSER |
Парткод: | 302FZ39710 |
Деталь: | Plate Fuser |
Парткод: | 302FZ02720 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | FRAME FUSER UNIT CENTER |
Парткод: | 302FZ02250 |
Деталь: | WIRE FUSER PRI |
Парткод: | 302FZ46290 |
Деталь: | SCREW A |
Парткод: | 2BG02410 |
Деталь: | STAY UPPER REAR |
Парткод: | 302FZ02341 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210002++H01 |
Деталь: | DUCT PU UPPER REAR |
Парткод: | 302FZ33120 |
Деталь: | DUCT PU LOWER |
Парткод: | 302FZ33210 |
Деталь: | DUCT PU UPPER |
Парткод: | 302FZ33220 |
Деталь: | PARTS,FAN COOLING DLP 70 SP |
Парткод: | 302FZ94380 |
Деталь: | WIRE LSU FAN |
Парткод: | 302FZ46670 |
Деталь: | STAY ISU UPPER RIGHT |
Парткод: | 302FZ02360 |
Деталь: | STAY ISU MIDDLE RIGHT |
Парткод: | 302FZ02380 |
Деталь: | MOUNT ISU ADJUST |
Парткод: | 302FZ02790 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210003++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210006++H01 |
Деталь: | LEVER LOCK CASSETTE |
Парткод: | 302GR02221 |
Деталь: | SPRING LEVER |
Парткод: | 302GR02230 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | MOUNT FRONT SIDE TOP |
Парткод: | 302FZ02970 |
Деталь: | GROUND PLATE ISU C |
Парткод: | 302GR02570 |
Деталь: | GROUND PLATE ISU D |
Парткод: | 302GR02580 |
Деталь: | FULCRUM PLATE,MIDDLE TRAY |
Парткод: | 2BJ02110 |
Деталь: | HOLDER,FULCRUM |
Парткод: | 2BJ02121 |
Деталь: | COVER FRONT SIDE TOP |
Парткод: | 302FZ04130 |
Деталь: | COVER EXIT FRONT |
Парткод: | 302FZ04140 |
Деталь: | MAGNET CLIP DISH |
Парткод: | 302GR04370 |
Деталь: | SEAL MAGNET |
Парткод: | 302GR04380 |
Деталь: | CLIP DISH |
Парткод: | 302FZ04450 |
Деталь: | STAY UPPER LEFT |
Парткод: | 302FZ02320 |
Деталь: | PLATE FRAME FUSER F |
Парткод: | 302FZ39740 |
Деталь: | JOINT TUBE B |
Парткод: | 302FZ33280 |
Деталь: | TUBE COOLING EXIT |
Парткод: | 302FZ33350 |
Деталь: | SPRING TUBE |
Парткод: | 302FZ33390 |
Деталь: | PLATE EARTH FRAME REAR |
Парткод: | 302FZ39750 |
Деталь: | PLATE EARTH FRAME FRONT |
Парткод: | 302FZ39760 |
Деталь: | MOUNT RUBBER ISU |
Парткод: | 302GR02311 |
Деталь: | ADJUSTOR ISU |
Парткод: | 302GR02321 |
Деталь: | CLAMP,EMT-3N(TAKEUCHI) |
Парткод: | M7005010 |
Деталь: | SHEET RAIL BYPASS |
Парткод: | 302FZ24170 |
Деталь: | SHIELD LSU WIRE |
Парткод: | 302FZ39490 |
Деталь: | SHIELD GASKET |
Парткод: | 7ZG65TAV+080H01 |
Деталь: | WIRE KEYCOUNTOR (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ46500 |
Деталь: | WIRE APC FAN (40/35ppm) |
Парткод: | 302JD46060 |
Деталь: | RACK,CURSOR |
Парткод: | 2BC06750 |
Деталь: | LEFT WIRE B,LIFT |
Парткод: | 2BC07340 |
Деталь: | TERMINAL,PAPER SIZE DETECTION |
Парткод: | 2BC07860 |
Деталь: | STOPPER BYPASS TABLE |
Парткод: | 2FB07330 |
Деталь: | SIZE DETECTION ASSY |
Парткод: | 2FG01020 |
Деталь: | TABLE A,BYPASS(G E) |
Парткод: | 302BC43134 |
Деталь: | TABLE B,BYPASS(G E) |
Парткод: | 302BC43146 |
Деталь: | TABLE C,BYPASS(G E) |
Парткод: | 302BC43152 |
Деталь: | TABLE D,BYPASS(G E) |
Парткод: | 302BC43161 |
Деталь: | SPRING BYPASS TEBLE |
Парткод: | 302FB17700 |
Деталь: | GEAR 18 IDLE DEVELOPING |
Парткод: | 302FB17710 |
Деталь: | SPONGE BYPASS TABLE |
Парткод: | 302FB17720 |
Деталь: | SEAL BYPASS TABLE |
Парткод: | 302FB17730 |
Деталь: | SIZE INDICATOR BYPASS(M) |
Парткод: | 302FB17740 |
Деталь: | SIZE INDICATOR BYPASS(I) |
Парткод: | 302FB17750 |
Деталь: | PIN BYPASS TABLE |
Парткод: | 302FB17800 |
Деталь: | SWITCH BYPASS SIZE |
Парткод: | 302FB25140 |
Деталь: | CURSOR MPT F |
Парткод: | 302FZ08330 |
Деталь: | CURSOR MPT R |
Парткод: | 302FZ08340 |
Деталь: | LABEL MP CAUTION J V |
Парткод: | 302FZ08480 |
Деталь: | LABEL MP CAUTION E V |
Парткод: | 302FZ08490 |
Деталь: | LABEL MP CAUTION TW V |
Парткод: | 302FZ08530 |
Деталь: | LABEL MP CAUTION KS V |
Парткод: | 302FZ08540 |
Деталь: | PAD MP L |
Парткод: | 302FZ08500 |
Деталь: | LABEL MP CAUTION PIC V |
Парткод: | 302FZ08560 |
Деталь: | WIRE BYPASS TRAY |
Парткод: | 302FZ46840 |
Деталь: | LABEL ORIGINAL MAX |
Парткод: | 303H605010 |
Деталь: | COVER,CURSOR |
Парткод: | 33906900 |
Деталь: | PAD, LIFT |
Парткод: | 3C007060 |
Деталь: | ORIGINAL SIZE SWITCH |
Парткод: | 76727010 |
Деталь: | BINDING BAND,T18R |
Парткод: | M2307010 |
Деталь: | LABEL MP CAUTION 3 V |
Парткод: | 302FZ08510 |
Деталь: | LABEL MP CAUTION 6 V |
Парткод: | 302FZ08520 |
Деталь: | PARTS TRAY ASSY |
Парткод: | 302FZ93363 |
Деталь: | BUSH 6 |
Парткод: | 2BG22960 |
Деталь: | GEAR Z15 REGIST |
Парткод: | 2C916180 |
Деталь: | PIPE JOINT ICL |
Парткод: | 302FZ23600 |
Деталь: | SCREW WT ICL |
Парткод: | 302FZ23610 |
Деталь: | SEAL PIPE WT ICL |
Парткод: | 302FZ23640 |
Деталь: | PIPE WT ICL |
Парткод: | 302FZ23650 |
Деталь: | SEAL SHUTTER ICL |
Парткод: | 302FZ23710 |
Деталь: | SPRING SHUTTER WASTE/A-80 A4 |
Парткод: | 5MMW465LD003 |
Деталь: | SHUTTER WASTE /43587J2027 A4 |
Парткод: | 5MVX332DB020 |
Деталь: | GUIDE BELT UP |
Парткод: | 302FZ21242 |
Деталь: | HOLDER GUIDE PULLEY |
Парткод: | 302FZ21700 |
Деталь: | PULLEY GUIDE |
Парткод: | 302FZ25940 |
Деталь: | PARTS,FAN IMAGE SP |
Парткод: | 302FZ94660 |
Деталь: | WASTE BOTTLE ASSY |
Парткод: | 302FZ00700 |
Деталь: | PARTS,ICL WT ASSY SP |
Парткод: | 302FZ94320 |
Деталь: | PARTS TRANSFER BELT ASSY |
Парткод: | 302FZ93094 |
Деталь: | PARTS,MOTOR IMAGE SP |
Парткод: | 302FZ94250 |
Деталь: | PLATE DRIVE TC |
Парткод: | 302FZ31150 |
Деталь: | GEAR Z84L Z30L TC |
Парткод: | 302FZ31560 |
Деталь: | CLUTCH REGIST 8 |
Парткод: | 302FZ31810 |
Деталь: | STOPPER 5 |
Парткод: | 2BC06980 |
Деталь: | WIRE REG CLT JOINT |
Парткод: | 302FZ46761 |
Деталь: | MOTOR LIFT |
Парткод: | 302GR44112 |
Деталь: | BUSHING 8 |
Парткод: | 2BC06510 |
Деталь: | SPRING COUPLING DLP |
Парткод: | 2BG22530 |
Деталь: | MOTOR DLP |
Парткод: | 302FZ31030 |
Деталь: | HOLDER DRUM DRIVE |
Парткод: | 302FZ31080 |
Деталь: | PLATE DRUM DRIVE |
Парткод: | 302FZ31092 |
Деталь: | SHAFT DLP DRIVE |
Парткод: | 302FZ31180 |
Деталь: | SHAFT CLN DRIVE |
Парткод: | 302FZ31190 |
Деталь: | COUPLING DLP DRIVE |
Парткод: | 302FZ31250 |
Деталь: | COLLAR DLP COUPLING |
Парткод: | 302FZ31280 |
Деталь: | GEAR Z22L DLP |
Парткод: | 302FZ31330 |
Деталь: | GEAR Z24R |
Парткод: | 302FZ31340 |
Деталь: | GEAR Z22R |
Парткод: | 302FZ31350 |
Деталь: | GEAR Z50L |
Парткод: | 302FZ31360 |
Деталь: | GEAR Z52R |
Парткод: | 302FZ31370 |
Деталь: | GEAR Z55L |
Парткод: | 302FZ31380 |
Деталь: | GEAR Z60L |
Парткод: | 302FZ31390 |
Деталь: | GEAR Z54L-Z26L |
Парткод: | 302FZ31401 |
Деталь: | GEAR Z42R-Z29R |
Парткод: | 302FZ31410 |
Деталь: | GEAR Z28R |
Парткод: | 302FZ31600 |
Деталь: | PIN MAIN DRIVE |
Парткод: | 302FZ31720 |
Деталь: | GEAR Z22L CLN |
Парткод: | 302FZ31850 |
Деталь: | GEAR Z35L DLP |
Парткод: | 302FZ31890 |
Деталь: | GEAR Z60L CLN |
Парткод: | 302FZ31900 |
Деталь: | HOLDER DRUM MOTOR |
Парткод: | 302FZ32051 |
Деталь: | SHEET DLP MOTOR |
Парткод: | 302FZ39800 |
Деталь: | SHEET MAIN DRIVE R |
Парткод: | 302FZ39960 |
Деталь: | PARTS,PWB MOTOR DRIVER ASSY,SP |
Парткод: | 302FZ94670 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | BUSH 6 |
Парткод: | 2BG22960 |
Деталь: | PLATE MPF DRIVE |
Парткод: | 302FZ31100 |
Деталь: | HOLDER MPF DRIVE |
Парткод: | 302FZ31111 |
Деталь: | GEAR Z98L-Z40R MPF |
Парткод: | 302FZ31140 |
Деталь: | SHAFT MPF CL |
Парткод: | 302FZ31160 |
Деталь: | SHAFT BYPASS DRIVE |
Парткод: | 302FZ31220 |
Деталь: | SHAFT BRS DRIVE |
Парткод: | 302FZ31230 |
Деталь: | GEAR Z94L-Z32L MPF |
Парткод: | 302FZ31290 |
Деталь: | GEAR Z38R MPF |
Парткод: | 302FZ31300 |
Деталь: | GEAR Z24R BRS |
Парткод: | 302FZ31310 |
Деталь: | GEAR Z20S BRS |
Парткод: | 302FZ31320 |
Деталь: | GEAR Z26L BYPASS |
Парткод: | 302FZ31540 |
Деталь: | GEAR Z27S BYPASS |
Парткод: | 302FZ31550 |
Деталь: | PIN MPF DRIVE |
Парткод: | 302FZ31710 |
Деталь: | CLUTCH FEED 6 |
Парткод: | 302FZ31820 |
Деталь: | SEAL MPF CL |
Парткод: | 302FZ32060 |
Деталь: | BUSHING 6 |
Парткод: | 3CY07080 |
Деталь: | CUT WASHER |
Парткод: | 5MVS665KB001 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | PARTS MOTOR DRUM |
Парткод: | 302FZ93440 |
Деталь: | JOINT DRUM |
Парткод: | 302FZ31270 |
Деталь: | STOPPER D MOTOR |
Парткод: | 302FZ31990 |
Деталь: | WIRE DLP MOTOR |
Парткод: | 302FZ46081 |
Деталь: | WIRE DRUM MOTOR SIG |
Парткод: | 302FZ46191 |
Деталь: | WIRE LIFT MOT |
Парткод: | 302FZ46250 |
Деталь: | WIRE DRM MOT A |
Парткод: | 302FZ46832 |
Деталь: | CORE 8-16X10 |
Парткод: | 3HK27050 |
Деталь: | WIRE TRNS MOT JOINT |
Парткод: | 302FZ46850 |
Деталь: | BEARING PRESS ROLLER |
Парткод: | 2FG20310 |
Деталь: | SPRING JOINT D |
Парткод: | 302BG22021 |
Деталь: | PARTS DR-820 |
Парткод: | 302FZ93260 |
Деталь: | PARTS MPF DRIVE ASSY |
Парткод: | 302FZ93250 |
Деталь: | BUSH 6 |
Парткод: | 2BG22960 |
Деталь: | BUSH 6 EW |
Парткод: | 2BG22970 |
Деталь: | CUT WASHER 4 |
Парткод: | 2BG22990 |
Деталь: | PULLEY MPT BYPASS |
Парткод: | 302FZ07020 |
Деталь: | BASE MPT BYPASS |
Парткод: | 302FZ07042 |
Деталь: | COVER MPT BYPASS |
Парткод: | 302FZ07051 |
Деталь: | GUIDE BYPASS RIGHT |
Парткод: | 302FZ07061 |
Деталь: | COVER BYPASS OUT |
Парткод: | 302FZ07070 |
Деталь: | PULLEY BYPASS |
Парткод: | 302FZ07080 |
Деталь: | BELT BYPASS |
Парткод: | 302FZ07090 |
Деталь: | GEAR BYPASS A |
Парткод: | 302FZ07100 |
Деталь: | SPRING BYPASS PULLEY |
Парткод: | 302FZ07110 |
Деталь: | GEAR BYPASS JOINT |
Парткод: | 302FZ07120 |
Деталь: | SPRING BYPASS MOTION |
Парткод: | 302FZ07130 |
Деталь: | COVER MPT REAR |
Парткод: | 302FZ07140 |
Деталь: | PULLEY TENSION BELT |
Парткод: | 302FZ07150 |
Деталь: | PLATE EARTH MPT |
Парткод: | 302FZ07180 |
Деталь: | SPRING EARTH BYPASS |
Парткод: | 302FZ07190 |
Деталь: | SPRING EARTH BYPASS JOINT |
Парткод: | 302FZ07210 |
Деталь: | GUIDE BYPASS IN |
Парткод: | 302FZ07231 |
Деталь: | SLIDER BYPASS A |
Парткод: | 302FZ07240 |
Деталь: | SLIDER BYPASS B |
Парткод: | 302FZ07250 |
Деталь: | PLATE GUIDE MPT |
Парткод: | 302FZ07301 |
Деталь: | BUSH CONTACT MPT B |
Парткод: | 302FZ07310 |
Деталь: | SPRING EARTH MPT A |
Парткод: | 302FZ07320 |
Деталь: | SPRING EARTH MPT B |
Парткод: | 302FZ07330 |
Деталь: | LABEL JAM BYPASS B2 |
Парткод: | 302FZ07350 |
Деталь: | LABEL JAM BYPASS B3 |
Парткод: | 302FZ07360 |
Деталь: | SPRING BYPASS PULLEY B |
Парткод: | 302FZ07380 |
Деталь: | ROLLER BYPASS C |
Парткод: | 302FZ07390 |
Деталь: | LEVER JAM BYPASS |
Парткод: | 302FZ07400 |
Деталь: | MOUNT LEVER BYPASS |
Парткод: | 302FZ07410 |
Деталь: | LABEL JAM BYPASS B4 |
Парткод: | 302FZ07420 |
Деталь: | HOLDER SHAFT OUT |
Парткод: | 302FZ07540 |
Деталь: | SHEET BYPASS OUT |
Парткод: | 302FZ07550 |
Деталь: | STOPPER EARTH MIDDLE |
Парткод: | 302FZ22760 |
Деталь: | COLLAR DU PULLEY |
Парткод: | 302FZ29140 |
Деталь: | CUT WASHER |
Парткод: | 5MVS665KB001 |
Деталь: | PARTS, ROLLER BYPASS A SP |
Парткод: | 302FZ94470 |
Деталь: | PARTS, ROLLER BYPASS B SP |
Парткод: | 302FZ94481 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | PARTS MPT BYPASS ASSY |
Парткод: | 302FZ93212 |
Деталь: | LOWER WING TRAY |
Парткод: | 2BJ60530 |
Деталь: | UPPER WING TRAY |
Парткод: | 302BJ60521 |
Деталь: | RAIL WING TRAY |
Парткод: | 302BJ60541 |
Деталь: | MOUNT WING TRAY |
Парткод: | 302GR04490 |
Деталь: | HOLDER WING TRAY |
Парткод: | 302GR04500 |
Деталь: | SOCKET ASSY,KEY COUNTER |
Парткод: | 3029236241 |
Деталь: | COVER,KEY COUNTER |
Парткод: | 3066060011 |
Деталь: | RETAINER,KEY COUNTER COVER |
Парткод: | 3066060023 |
Деталь: | RETAINER,KEY COUNTER |
Парткод: | 3066060031 |
Деталь: | MOUNT,KEY COUNTER |
Парткод: | 3066060041 |
Деталь: | KEY COUNTER |
Парткод: | 82142540 |
Деталь: | MOUNT KEY COUNTER |
Парткод: | 302FZ03010 |
Деталь: | SET PARTS KEYCOUNTER NEW COLOR |
Парткод: | 302A369707 |
Деталь: | PARTS CONT DRIVE ASSY |
Парткод: | 302FZ93290 |
Деталь: | PARTS ICL MOTOR ASSY |
Парткод: | 302FZ93460 |
Деталь: | COVER INNER UPPER |
Парткод: | 302FZ04520 |
Деталь: | MAGNET CATCH |
Парткод: | 60804120 |
Деталь: | PLATE DUCT EXIT |
Парткод: | 302FZ33370 |
Деталь: | SEAL BRACKET FAN C |
Парткод: | 302FZ33400 |
Деталь: | DUCT EXIT MOTOR |
Парткод: | 302FZ33360 |
Деталь: | CORE 8-16X10 |
Парткод: | 3HK27050 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610008++H01 |
Деталь: | LEVER LOCK CONT |
Парткод: | 302FZ04530 |
Деталь: | RFID RECIEVER |
Парткод: | 302FZ45060 |
Деталь: | COVER CONNECTER |
Парткод: | 302FZ04580 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610002++H01 |
Деталь: | FAN 80 COOLING |
Парткод: | 2FB27180 |
Деталь: | BRACKET FAN D |
Парткод: | 302FZ33231 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | BRACKET FAN C |
Парткод: | 302FZ33191 |
Деталь: | PARTS,FAN COOLING CONVEYING SP |
Парткод: | 302FZ94420 |
Деталь: | MOUNT FAN |
Парткод: | 302FZ02640 |
Деталь: | PARTS,FAN COOLING DLP 70 SP |
Парткод: | 302FZ94380 |
Деталь: | BRACKET FAN A |
Парткод: | 302FZ33140 |
Деталь: | SEAL BRACKET FAN A |
Парткод: | 302FZ33170 |
Деталь: | SEAL BRACKET FAN B |
Парткод: | 302FZ33180 |
Деталь: | BRACKET FAN B |
Парткод: | 302FZ33150 |
Деталь: | WIRE FRONT SIDE |
Парткод: | 302FZ46091 |
Деталь: | FAN 60 COOLING |
Парткод: | 2FB27190 |
Деталь: | DUCT EXIT LOWER |
Парткод: | 302FZ33011 |
Деталь: | DUCT EXIT UPPER |
Парткод: | 302FZ33020 |
Деталь: | SEAL DUCT EXIT |
Парткод: | 302FZ33380 |
Деталь: | SEAL BRACKET FAN D |
Парткод: | 302FZ33411 |
Деталь: | BRACKET PWB RFID |
Парткод: | 302FZ02880 |
Деталь: | SEAL BRACKET FAN E |
Парткод: | 302FZ33420 |
Деталь: | FAN 60 COOLING |
Парткод: | 2FB27190 |
Деталь: | SHIELD BOX |
Парткод: | 302FZ39051 |
Деталь: | BRACKET INLET |
Парткод: | 302FZ39550 |
Деталь: | LVU 100 |
Парткод: | 302FZ45010 |
Деталь: | LVU 200 |
Парткод: | 302FZ45020 |
Деталь: | WIRE CASSETTE HEATER |
Парткод: | 302FZ46430 |
Деталь: | WIRE INLET ASSY |
Парткод: | 302FZ46661 |
Деталь: | WIRE OP HEATER |
Парткод: | 302FZ46730 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210002++H01 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210003++H01 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210004++H01 |
Деталь: | ACCESS.SPACER |
Парткод: | 7YZM510007++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | PLATE EARTH IPU |
Парткод: | 302FZ39930 |
Деталь: | SPRING HV TC1 |
Парткод: | 302FZ39540 |
Деталь: | TERMINAL TC1 |
Парткод: | 302FZ39570 |
Деталь: | HVU TRANSFER 1 (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ45041 |
Деталь: | PARTS,PWB HVU TRANSFER 1 ASSY SP (40/35ppm) |
Парткод: | 302JD94100 |
Деталь: | MOUNT TRANSFER HV (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ39590 |
Деталь: | MOUNT TRANSFER HV (40/35ppm) |
Парткод: | 302JD39010 |
Деталь: | WIRE FAX POWER |
Парткод: | 302FZ46641 |
Деталь: | GUIDE WIRE LOWER |
Парткод: | 302FZ39870 |
Деталь: | WIRE HVU 2 (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ46120 |
Деталь: | WIRE HVU 2 (40/35ppm) |
Парткод: | 302JD46020 |
Деталь: | LID VENDOR |
Парткод: | 302FB26290 |
Деталь: | MOUNT OPTION IF |
Парткод: | 302FZ39071 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610015++H01 |
Деталь: | WIRE OP DESK |
Парткод: | 302FZ46742 |
Деталь: | WIRE LVU ENGINE |
Парткод: | 302FZ46220 |
Деталь: | WIRE LVU CONTROLLER |
Парткод: | 302FZ46240 |
Деталь: | WIRE FUSER (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ46170 |
Деталь: | WIRE FUSER (40/35ppm) |
Парткод: | 302JD46100 |
Деталь: | WIRE INTERLOCK SWITCH |
Парткод: | 302FZ46210 |
Деталь: | WIRE LVU IPU |
Парткод: | 302FZ46231 |
Деталь: | WIRE OPTION SIGNAL |
Парткод: | 302FZ46392 |
Деталь: | PLATE MAIN SW |
Парткод: | 302FZ39731 |
Деталь: | WIRE MSW |
Парткод: | 302FZ46260 |
Деталь: | SW. SEESAW |
Парткод: | 7SC010101+++H01 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210006++H01 |
Деталь: | SHEET WIRE LOWER |
Парткод: | 302FZ39880 |
Деталь: | SHEET TRANSFER HV (40/35ppm) |
Парткод: | 302JD39020 |
Деталь: | POWER CORD(120) |
Парткод: | 3019527401 |
Деталь: | POWER CORD(230) |
Парткод: | 2AR27800 |
Деталь: | POWER CODE AS(240) |
Парткод: | 3029927232 |
Деталь: | POWER CORD 110 |
Парткод: | 3065027601 |
Деталь: | GEAR MAG Z14H |
Парткод: | 302FZ14161 |
Деталь: | GEAR IDLE Z15H DLP |
Парткод: | 302FZ14170 |
Деталь: | GEAR SLEEVE Z17H |
Парткод: | 302FZ14180 |
Деталь: | GEAR Z14S |
Парткод: | 302FZ14230 |
Деталь: | COVER FRONT DLP |
Парткод: | 302FZ14300 |
Деталь: | COVER REAR BK DLP |
Парткод: | 302FZ14310 |
Деталь: | COVER REAR Y DLP |
Парткод: | 302FZ14420 |
Деталь: | COVER REAR C DLP |
Парткод: | 302FZ14430 |
Деталь: | COVER REAR M DLP |
Парткод: | 302FZ14440 |
Деталь: | STUD SCREW M4 |
Парткод: | 302FZ14840 |
Деталь: | PARTS DLP K ASSY |
Парткод: | 302FZ93113 |
Деталь: | PARTS DLP Y ASSY |
Парткод: | 302FZ93123 |
Деталь: | PARTS DLP C ASSY |
Парткод: | 302FZ93133 |
Деталь: | PARTS DLP M ASSY |
Парткод: | 302FZ93143 |
Деталь: | SWITCH,COVER OPEN |
Парткод: | 66127010 |
Деталь: | MOUNT CASSETTE SW |
Парткод: | 302FZ02610 |
Деталь: | WIRE FEED JOINT (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302HP46050 |
Деталь: | WIRE FEED JOINT (40/35ppm) |
Парткод: | 302JD46010 |
Деталь: | CONNECTOR |
Парткод: | 7YCC08B2046+H02 |
Деталь: | RETAINING PIN DRAWER |
Парткод: | 302FZ03070 |
Деталь: | MOUNT HV TERMINAL |
Парткод: | 302FZ39110 |
Деталь: | SPRING HV MAIN |
Парткод: | 302FZ39520 |
Деталь: | HVU MAIN (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302JG45010 |
Деталь: | PARTS,PWB HVU MAIN ASSY SP (40/35ppm) |
Парткод: | 302JD94120 |
Деталь: | GUIDE WIRE MAIN |
Парткод: | 302FZ39210 |
Деталь: | SHEET PWB |
Парткод: | 302FZ39900 |
Деталь: | MOUNT HV LOWER |
Парткод: | 302FZ39920 |
Деталь: | HEATER DEHUMIDIFIER 120 |
Парткод: | 302FZ45170 |
Деталь: | HEATER DEHUMIDIFIER 240 |
Парткод: | 302FZ45160 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | GUIDE WIRE SUB |
Парткод: | 302FZ39220 |
Деталь: | SPRING ICL |
Парткод: | 302FZ39530 |
Деталь: | TERMINAL ICL |
Парткод: | 302FZ39580 |
Деталь: | WIRE CLEANING |
Парткод: | 302FZ46270 |
Деталь: | WIRE MPF |
Парткод: | 302FZ46031 |
Деталь: | COVER CONN |
Парткод: | 302GR39190 |
Деталь: | LABEL L,HIGH TEMPERATURE CAUTION |
Парткод: | 20305130 |
Деталь: | COVER INNER RIGHT |
Парткод: | 302FZ04200 |
Деталь: | BRUSH CLEANER |
Парткод: | 2BL16220 |
Деталь: | COVER INNER LEFT |
Парткод: | 302FZ04210 |
Деталь: | SHEET HARNESS LEFT |
Парткод: | 302FZ04640 |
Деталь: | LABEL SEP CLEANING |
Парткод: | 302GR34181 |
Деталь: | SWITCH,SIZE |
Парткод: | 35927420 |
Деталь: | MAGNET CATCH |
Парткод: | 60804120 |
Деталь: | SENSOR HUMIDITY |
Парткод: | 2FB27060 |
Деталь: | SPACER SENSOR |
Парткод: | 302FZ04730 |
Деталь: | COVER RIGHT TRAY |
Парткод: | 302FZ04190 |
Деталь: | COVER TOP |
Парткод: | 302FZ04040 |
Деталь: | REAR COVER TRAY |
Парткод: | 2BJ04031 |
Деталь: | COVER LEFT FRONT TOP |
Парткод: | 302FZ04430 |
Деталь: | COVER LEFT REAR TOP |
Парткод: | 302FZ04440 |
Деталь: | CUT WASHER 4 |
Парткод: | 2BG22990 |
Деталь: | COVER LEFT REAR |
Парткод: | 302FZ04160 |
Деталь: | LID COVER LEFT |
Парткод: | 302FZ04240 |
Деталь: | SPRING COVER R /40283V0069 A4 |
Парткод: | 5MMW261SD004 |
Деталь: | LOCK COVER R /40283V0068 A4 |
Парткод: | 5MVX421DN003 |
Деталь: | COVER LEFT FRONT |
Парткод: | 302FZ04150 |
Деталь: | BAND B |
Парткод: | 2BG06480 |
Деталь: | SHAFT FEED B |
Парткод: | 302BG06152 |
Деталь: | PULLEY FEED |
Парткод: | 302BG06162 |
Деталь: | COVER FEED LOW |
Парткод: | 302FZ04350 |
Деталь: | SPRING FEED LOW |
Парткод: | 302FZ04761 |
Деталь: | Bush SP |
Парткод: | 302FZ24600 |
Деталь: | LABEL LEFT COVER A |
Парткод: | 302GR34040 |
Деталь: | COVER RIGHT |
Парткод: | 302FZ04060 |
Деталь: | COVER RIGHT MID A |
Парткод: | 302FZ04071 |
Деталь: | COVER FILTER |
Парткод: | 302FZ04470 |
Деталь: | FILTER DUST |
Парткод: | 302FZ04500 |
Деталь: | COVER MAIN SW |
Парткод: | 302FZ04630 |
Деталь: | LABEL JAM FUSER |
Парткод: | 302FZ34021 |
Деталь: | PLATE COVER LEFT MID |
Парткод: | 302FZ04830 |
Деталь: | PLATE MAGNET |
Парткод: | 302FZ04250 |
Деталь: | COVER FRONT SIDE MID |
Парткод: | 302FZ04120 |
Деталь: | PLATE MAGCHATCH |
Парткод: | 5MMS626SD003 |
Деталь: | STRAP COVER FRONT |
Парткод: | 302FZ04490 |
Деталь: | FILTER DUCT PU |
Парткод: | 302FZ33240 |
Деталь: | SHEET EMBLEM |
Парткод: | 302JD04070 |
Деталь: | COVER REAR |
Парткод: | 302FZ04231 |
Деталь: | COVER REAR (40/35ppm) |
Парткод: | 302JD04030 |
Деталь: | LID KMAS |
Парткод: | 2C912430 |
Деталь: | COVER REAR MOTOR (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ04881 |
Деталь: | COVER REAR MOTOR (40/35ppm) |
Парткод: | 302JD04010 |
Деталь: | LID SHIELD BOX (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ39640 |
Деталь: | LID SHIELD BOX (40/35ppm) |
Парткод: | 302JD04040 |
Деталь: | COVER FILTER DUCT PU |
Парткод: | 302FZ33250 |
Деталь: | LABEL CONTAINER T1 |
Парткод: | 4AK73740 |
Деталь: | LABEL CONTAINER T2 |
Парткод: | 4AK73750 |
Деталь: | LABEL CONTAINER T3 |
Парткод: | 4AK73760 |
Деталь: | LABEL CONTAINER T4 |
Парткод: | 4AK73770 |
Деталь: | COVER EXIT TOP |
Парткод: | 302FZ04180 |
Деталь: | COVER LEFT MID |
Парткод: | 302FZ04170 |
Деталь: | EMBLEM LOGO |
Парткод: | 302JD04060 |
Деталь: | BASE EMBLEM 2525E (25/25ppm) |
Парткод: | 302JL04010 |
Деталь: | BASE EMBLEM 3225E (32/25ppm) |
Парткод: | 302JJ04010 |
Деталь: | BASE EMBLEM 3232E (32/32ppm) |
Парткод: | 302JG04010 |
Деталь: | BASE EMBLEM 4035E (40/35ppm) |
Парткод: | 302JD04050 |
Деталь: | LABEL BOARD SET |
Парткод: | 302FZ34270 |
Деталь: | COVER CF |
Парткод: | 303JT39020 |
Деталь: | COVER FRONT |
Парткод: | 302FZ04010 |
Деталь: | CUSHION COVER FRONT |
Парткод: | 302FZ04710 |
Деталь: | LABEL CONTAINER |
Парткод: | 302FZ34230 |
Деталь: | LABEL CONTAINER OPE A |
Парткод: | 302FZ34250 |
Деталь: | LABEL CONTAINER OPE E |
Парткод: | 302FZ34260 |
Деталь: | LABEL CONTAINER OPE TW |
Парткод: | 302FZ34290 |
Деталь: | LABEL ENERGY STAR |
Парткод: | 302G634070 |
Деталь: | LABEL OFF CAUTION A |
Парткод: | 302GR34230 |
Деталь: | LABEL OFF CAUTION E |
Парткод: | 302FZ34010 |
Деталь: | LABEL OFF CAUTION TW |
Парткод: | 302FZ34280 |
Деталь: | COVER FRONT SIDE LOW |
Парткод: | 302FZ04110 |
Деталь: | PLATE EMBLEM |
Парткод: | 302JD04080 |
Деталь: | TAPE EMBLEM A |
Парткод: | 302JD04090 |
Деталь: | TAPE EMBLEM B |
Парткод: | 302JD04100 |
Деталь: | LABEL CAUTION HG |
Парткод: | 302DC05120 |
Деталь: | COVER INNER LEFT ASSY |
Парткод: | 302FZ00440 |
Деталь: | COVER LEFT REAR ASSY |
Парткод: | 302FZ00450 |
Деталь: | COVER LEFT FRONT ASSY |
Парткод: | 302FZ00460 |
Деталь: | PARTS COVER FEED LOW ASSY |
Парткод: | 302FZ93311 |
Деталь: | COVER FILTER ASSY |
Парткод: | 302FZ00470 |
Деталь: | FRONT COVER A ASSY SP |
Парткод: | 302FZ80070 |
Деталь: | FRONT COVER E ASSY SP |
Парткод: | 302FZ80080 |
Деталь: | FRONT COVER TW ASSY SP |
Парткод: | 302FZ80190 |
Деталь: | PARTS MC-820 (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ93480 |
Деталь: | PARTS MC-825 (40/35ppm) |
Парткод: | 302JD93120 |
Деталь: | PARTS DRUM ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ93102 |
Деталь: | PARTS DRUM ASSY (40/35ppm) |
Парткод: | 302JD93080 |
Деталь: | BUSH 6 EW |
Парткод: | 2BG22970 |
Деталь: | SENSOR 248NL1 |
Парткод: | 2C927210 |
Деталь: | SHAFT MIDDLE L |
Парткод: | 302FZ22140 |
Деталь: | PULLEY MIDDLE |
Парткод: | 302FZ22150 |
Деталь: | Bush SP |
Парткод: | 302FZ24600 |
Деталь: | FRAME DU |
Парткод: | 302FZ29012 |
Деталь: | GEAR DU Z32S |
Парткод: | 302FZ29040 |
Деталь: | GEAR DU IDLE |
Парткод: | 302FZ29050 |
Деталь: | PLATE EARTH DU |
Парткод: | 302FZ29061 |
Деталь: | ACTUATOR DU |
Парткод: | 302FZ29070 |
Деталь: | RETAINER ACTUATOR DU |
Парткод: | 302FZ29080 |
Деталь: | SPRING ACT DU |
Парткод: | 302FZ29090 |
Деталь: | BELT DU |
Парткод: | 302FZ29110 |
Деталь: | PULLEY DU BELT |
Парткод: | 302FZ29120 |
Деталь: | SPRING DU |
Парткод: | 302FZ29131 |
Деталь: | COLLAR DU PULLEY |
Парткод: | 302FZ29140 |
Деталь: | MOTOR DU |
Парткод: | 302FZ31071 |
Деталь: | WIRE DU PI |
Парткод: | 302FZ46680 |
Деталь: | PARTS, ROLLER DUPLEX A SP |
Парткод: | 302FZ94620 |
Деталь: | PARTS, ROLLER DUPLEX B SP |
Парткод: | 302FZ94630 |
Деталь: | LABEL JAM CONVEYING |
Парткод: | 302HP34040 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | CUT WASHER 4 |
Парткод: | 2BG22990 |
Деталь: | COVER LEFT |
Парткод: | 302FZ04302 |
Деталь: | LEVER LEFT COVER |
Парткод: | 302FZ04321 |
Деталь: | SHAFT HOOK |
Парткод: | 302FZ04330 |
Деталь: | PLATE LEFT COVER F |
Парткод: | 302FZ04360 |
Деталь: | PLATE LEFT COVER R |
Парткод: | 302FZ04370 |
Деталь: | SPRING LEFT COVER F |
Парткод: | 302FZ04390 |
Деталь: | SPRING LEFT COVER R |
Парткод: | 302FZ04400 |
Деталь: | HOOK LEFT COVER F |
Парткод: | 302FZ04800 |
Деталь: | HOOK LEFT COVER R |
Парткод: | 302FZ04810 |
Деталь: | PLATE LEFT COVER C |
Парткод: | 302FZ04970 |
Деталь: | PLATE LEFT COVER D |
Парткод: | 302FZ04980 |
Деталь: | SHEET LEFT PLATE |
Парткод: | 302FZ24150 |
Деталь: | GUIDE CHANGE L |
Парткод: | 302FZ28050 |
Деталь: | SPRING SEPARATE |
Парткод: | 302FZ28230 |
Деталь: | SHEET SILENCER EXIT |
Парткод: | 302FZ28280 |
Деталь: | SHIELD GASKET |
Парткод: | 7ZG65TSV+020H01 |
Деталь: | SHIELD GASKET |
Парткод: | 7ZGSTG77+014H01 |
Деталь: | LABEL VFEED CAUTION |
Парткод: | 302FB05380 |
Деталь: | LABEL VFEED CAUTION TW |
Парткод: | 302GR34420 |
Деталь: | SHAFT LEFT COVER |
Парткод: | 302FZ04310 |
Деталь: | SHAFT LEFT COVER B |
Парткод: | 302FZ04420 |
Деталь: | BAND LEFT COVER |
Парткод: | 302FZ04990 |
Деталь: | LABEL VFEED CAUTION 6NATIONS |
Парткод: | 302FB05440 |
Деталь: | PARTS DU ASSY |
Парткод: | 302FZ93500 |
Деталь: | PARTS LEFT COVER ASSY |
Парткод: | 302FZ93490 |
Деталь: | TERMINAL,PAPER SIZE DETECTION |
Парткод: | 2BC07860 |
Деталь: | PLATE NUMBER |
Парткод: | 2BL04310 |
Деталь: | CUT WASHER 5 |
Парткод: | 2C904550 |
Деталь: | PIN CURSOR |
Парткод: | 2FB07050 |
Деталь: | SPRING CURSOR |
Парткод: | 2FB07060 |
Деталь: | SIZE DETECTION ASSY |
Парткод: | 2FG01020 |
Деталь: | SHAFT, WORK PLATE |
Парткод: | 302AR07041 |
Деталь: | WORK PLATE,LIFT CASSETTE |
Парткод: | 302BC06091 |
Деталь: | PLATE SIZE C |
Парткод: | 302FB05200 |
Деталь: | PLATE SIZE IN |
Парткод: | 302FB05210 |
Деталь: | LEVER CURSOR A |
Парткод: | 302FB07032 |
Деталь: | LEVER CURSOR B |
Парткод: | 302FB07042 |
Деталь: | ADJUSTING PLATE CASSETTE |
Парткод: | 302FB07340 |
Деталь: | PIN CASSETTE |
Парткод: | 302FB07420 |
Деталь: | BASE CASSETTE |
Парткод: | 302FG07091 |
Деталь: | GROUND PLATE,CASSETTE |
Парткод: | 302FG07200 |
Деталь: | COVER CASSETTE |
Парткод: | 302FZ04090 |
Деталь: | CASSETTE |
Парткод: | 302FZ09011 |
Деталь: | CURSOR RIGHT |
Парткод: | 302FZ09030 |
Деталь: | CURSOR RIGHT UPPER |
Парткод: | 302FZ09040 |
Деталь: | SHAFT HANDLE |
Парткод: | 302FZ09070 |
Деталь: | LABEL CASSETTE OPERATION 1 |
Парткод: | 302FZ09090 |
Деталь: | LABEL BYPASS OPERATION |
Парткод: | 302FZ09101 |
Деталь: | LABEL CURSOR OPERATION |
Парткод: | 302FZ09111 |
Деталь: | SPONGE FRONT |
Парткод: | 302FZ09120 |
Деталь: | LABEL PAPER MAX |
Парткод: | 302FZ09130 |
Деталь: | LABEL PAPER SIZE R1 |
Парткод: | 302FZ09141 |
Деталь: | LABEL PAPER UPPER LIMIT |
Парткод: | 302FZ09150 |
Деталь: | HANDLE CASSETTE 1 |
Парткод: | 302GR09020 |
Деталь: | HANDLE CASSETTE 2 |
Парткод: | 302GR09040 |
Деталь: | LEVER CASSETTE |
Парткод: | 302GR09051 |
Деталь: | RAIL CURSOR R |
Парткод: | 302GR09060 |
Деталь: | LID PAPER SIZE |
Парткод: | 302GR09070 |
Деталь: | RAIL CURSOR A |
Парткод: | 302GR09080 |
Деталь: | Support Plate |
Парткод: | 302GR09090 |
Деталь: | FRONT CURSOR CASSETTE |
Парткод: | 302GR09102 |
Деталь: | REAR CURSOR CASSETTE |
Парткод: | 302GR09112 |
Деталь: | SPRING LEVER CASSETTE |
Парткод: | 302GR09120 |
Деталь: | SHAFT PULLEY |
Парткод: | 302GR09130 |
Деталь: | WORK PLATE HANDLE |
Парткод: | 302GR09150 |
Деталь: | STOPPER PAPER |
Парткод: | 302GR09160 |
Деталь: | SEAL DETECTION PLATE |
Парткод: | 302GR09210 |
Деталь: | SPACER SIZE PLATE |
Парткод: | 302GR09980 |
Деталь: | LIFT LOCK |
Парткод: | 302GR09990 |
Деталь: | LABEL PAPER SIZE |
Парткод: | 302GR34022 |
Деталь: | WIRE CASSETTE UNIT |
Парткод: | 302GR46450 |
Деталь: | DETECTION PLATE,PAPER SIZE |
Парткод: | 33907170 |
Деталь: | CUSHION,CASSETTE WORK PLATE |
Парткод: | 33907210 |
Деталь: | PULLEY,CASSETTE |
Парткод: | 34907150 |
Деталь: | RETAINER M4 |
Парткод: | 3CY06030 |
Деталь: | RACK CURSOR |
Парткод: | 3CY06090 |
Деталь: | GEAR 20,CURSOR |
Парткод: | 3CY06100 |
Деталь: | CUSHION,CASSETTE R |
Парткод: | 60907170 |
Деталь: | SPRING, PAD |
Парткод: | 66106080 |
Деталь: | PAD,CASSETTE |
Парткод: | 66107100 |
Деталь: | CONNECTOR |
Парткод: | 7YCC08B2046+H01 |
Деталь: | PARTS CASSETTE 1ST ASSY |
Парткод: | 302FZ93034 |
Деталь: | PULLEY,PAPER FEED |
Парткод: | 2AR07220 |
Цена: | 1 600 ₽ |
Деталь: | PULLEY,SEPARATION |
Парткод: | 2AR07230 |
Цена: | 360 ₽ |
Деталь: | GUIDE FILM,SEPARATION PULLEY |
Парткод: | 2AR07660 |
Деталь: | BUSHING 6,REGISTRATION |
Парткод: | 2BC06520 |
Деталь: | PULLEY FEED A |
Парткод: | 2BJ06010 |
Цена: | 250 ₽ |
Деталь: | PLATE LEADING FEED |
Парткод: | 2BL07900 |
Деталь: | SHAFT,PAPER FEED |
Парткод: | 302AR07251 |
Деталь: | SHAFT,LEADING FEED |
Парткод: | 302AR07271 |
Деталь: | UPPER HOUSING,PAPER FEED |
Парткод: | 302FG07251 |
Деталь: | LOWER HOUSING,PAPER FEED |
Парткод: | 302FG07260 |
Деталь: | ACTUATOR,PAPER EMPTY |
Парткод: | 302FG07290 |
Деталь: | HOLDER,ACTUATOR |
Парткод: | 302FG07300 |
Деталь: | REINFORCEMENT PRIMARY PAPER FEED |
Парткод: | 302FG07310 |
Деталь: | GROUND PLATE,PRIMARY PAPER FEED |
Парткод: | 302FG07330 |
Деталь: | HOLDER PICK |
Парткод: | 302GR06060 |
Деталь: | SUPPORT PLATE FEED |
Парткод: | 302GR06070 |
Деталь: | SPRING PICK |
Парткод: | 302GR06080 |
Деталь: | SPRING SEPARATION |
Парткод: | 302GR06091 |
Деталь: | SHAFT SEPARATION |
Парткод: | 302GR06101 |
Деталь: | TORQUE LIMITER 360 |
Парткод: | 302GR06110 |
Деталь: | LEVER SEPARATION RELEASE |
Парткод: | 302GR06201 |
Деталь: | WIRE PRIMARY FEED UNIT1 |
Парткод: | 302GR46430 |
Деталь: | GEAR 16,PAPER FEED |
Парткод: | 33906160 |
Деталь: | LOWER BUSHING,PAPER FEED |
Парткод: | 34806040 |
Деталь: | GEAR 15 |
Парткод: | 34922420 |
Деталь: | PT.SENSOR GP1A73AJ00/ BK |
Парткод: | 5FNXGP1A73A++02 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | CONNECTOR |
Парткод: | 7YCC08B2046+H01 |
Деталь: | PARTS FE-820 |
Парткод: | 302FZ93321 |
Деталь: | SEAL FRAME A |
Парткод: | 302GR17410 |
Деталь: | SEAL FRAME B |
Парткод: | 302GR17420 |
Деталь: | SEAL GUIDE WIRE D |
Парткод: | 302GR17450 |
Деталь: | SEAL FRAME C |
Парткод: | 302GR17460 |
Деталь: | PAD JS SENSOR |
Парткод: | 303KB28010 |
Деталь: | MOUNT DP HINGE |
Парткод: | 302GR17270 |
Деталь: | PIN WIRE PULLEY B |
Парткод: | 302GR17350 |
Деталь: | PULLEY SCANNER |
Парткод: | 302GR17820 |
Деталь: | DRUM PULLEY |
Парткод: | 2C912340 |
Деталь: | REAR WIRE SCANNER |
Парткод: | 302GR17100 |
Деталь: | FRONT WIRE SCANNER |
Парткод: | 302GR17110 |
Деталь: | SHAFT SCANNER |
Парткод: | 302GR17190 |
Деталь: | BEARING,688ZZNR |
Парткод: | 28107400 |
Деталь: | STOPPER 6 |
Парткод: | 2BC06910 |
Деталь: | PULLEY SCANNER 50 |
Парткод: | 302FZ17020 |
Деталь: | MIRROR FRAME B |
Парткод: | 302GR17091 |
Деталь: | MIRROR B |
Парткод: | 302GR17280 |
Деталь: | MIRROR HOLDER |
Парткод: | 75712080 |
Деталь: | SLIDER SCANNER |
Парткод: | 2DC12230 |
Деталь: | ADJUSTING PLATE B |
Парткод: | 302GR17131 |
Деталь: | GUIDE WIRE B |
Парткод: | 302GR17150 |
Деталь: | PULLEY PLATE B |
Парткод: | 302GR17980 |
Деталь: | SPRING SCANNER TENSION |
Парткод: | 302C912291 |
Деталь: | SPRING,MIRROR HOLDER |
Парткод: | 2BC12190 |
Деталь: | MIRROR A |
Парткод: | 2FB12140 |
Деталь: | MIRROR FRAME A |
Парткод: | 302GR17082 |
Деталь: | REFLECTOR SCANNER |
Парткод: | 302GR17250 |
Деталь: | FILM LAMP |
Парткод: | 302GR17400 |
Деталь: | TAPE REFLECTOR |
Парткод: | 302GR17620 |
Деталь: | RETAINER WIRE |
Парткод: | 2C912150 |
Деталь: | GUIDE WIRE C |
Парткод: | 302GR17160 |
Деталь: | LAMP SCANNER |
Парткод: | 302GR17120 |
Деталь: | GUIDE WIRE A |
Парткод: | 302GR17140 |
Деталь: | HOLDER GUIDE WIRE C |
Парткод: | 302GR17440 |
Деталь: | MOTOR SCANNER |
Парткод: | 302GR44270 |
Деталь: | PULLEY SCANNER 41/26 |
Парткод: | 302FZ17010 |
Деталь: | MOUNT SCANNER DRIVE |
Парткод: | 302FZ17030 |
Деталь: | CUT WASHER |
Парткод: | 5MVS665KB001 |
Деталь: | BELT SCANNER |
Парткод: | 302FZ17040 |
Деталь: | MOUNT RELEASE SWITCH |
Парткод: | 302GR17300 |
Деталь: | SWITCH RELEASE |
Парткод: | 302GR17370 |
Деталь: | SPRING RELEASE SWITCH |
Парткод: | 302GR17380 |
Деталь: | SENSOR 248NL1 |
Парткод: | 2C927210 |
Деталь: | SENSOR ORIGINAL |
Парткод: | 2C927090 |
Деталь: | GUIDE WIRE D |
Парткод: | 302GR17740 |
Деталь: | WIRE SHD-SCANNER PWB |
Парткод: | 302GR46021 |
Деталь: | WIRE SCANNER HP SW |
Парткод: | 302GR46040 |
Деталь: | WIRE CCD DATA NON SHIELD |
Парткод: | 302FZ46570 |
Деталь: | PRINTED W. BOARD SCANNER ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ01060 |
Деталь: | PARTS,PWB SCANNER ASSY SP (40/35ppm) |
Парткод: | 302JD94030 |
Деталь: | GUIDE FFC |
Парткод: | 302GR17340 |
Деталь: | GUIDE WIRE E |
Парткод: | 302GR17770 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | MOUNT SCANNER PWB |
Парткод: | 302GR17320 |
Деталь: | SEAL LAMP INVERTER |
Парткод: | 302GR17430 |
Деталь: | PRINTED W. BOARD SHD (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ01050 |
Деталь: | PARTS,PWB SHD ASSY SP (40/35ppm) |
Парткод: | 302JD94040 |
Деталь: | RETAINER REGURATOR |
Парткод: | 302GR17330 |
Деталь: | UNIT LAMP INVERTER |
Парткод: | 302GR45080 |
Деталь: | WIRE LAMP INVERTER |
Парткод: | 302GR46060 |
Деталь: | THERMAL SEAT |
Парткод: | 7ZS22110301+H01 |
Деталь: | HOLDER PI |
Парткод: | 302GR17750 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | WIRE SCANNER-IPU PWB |
Парткод: | 302FZ46560 |
Деталь: | ACCESS.BAND |
Парткод: | 7YZM410002++H01 |
Деталь: | SEAL SCANNER FRAME E |
Парткод: | 302GR17930 |
Деталь: | PLATE PULLEY |
Парткод: | 302GR17860 |
Деталь: | PULLEY,LIFT WIRE |
Парткод: | 2BC07050 |
Деталь: | SEAL SCANNER PWB |
Парткод: | 302GR17890 |
Деталь: | MIRROR C |
Парткод: | 302GR17960 |
Деталь: | PIN ROLLER RELEASE LEVER |
Парткод: | 302FB16320 |
Деталь: | SHIELD GASKET |
Парткод: | 7ZG65TSV+015H01 |
Деталь: | LID PWB S |
Парткод: | 302GR17730 |
Деталь: | PIN SCANNER RETAINING |
Парткод: | 302GR17180 |
Деталь: | BASE RUBBER,SCANNER SECTION |
Парткод: | 2AV12280 |
Деталь: | SPACER ISU |
Парткод: | 302FZ02390 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210003++H01 |
Деталь: | PLATE MIRROR B |
Парткод: | 302GR17830 |
Деталь: | SEAL PLATE MIRROR B |
Парткод: | 302GR17840 |
Деталь: | STOPPER PI |
Парткод: | 302GR17970 |
Деталь: | HOLDER BEARING |
Парткод: | 302GR17880 |
Деталь: | CUT WASHER 4 |
Парткод: | 2BG22990 |
Деталь: | TERMINAL,PAPER SIZE DETECTION |
Парткод: | 2BC07860 |
Деталь: | PLATE NUMBER |
Парткод: | 2BL04310 |
Деталь: | PLATE NUMBER 2 |
Парткод: | 2BL04370 |
Деталь: | CUT WASHER 5 |
Парткод: | 2C904550 |
Деталь: | PIN CURSOR |
Парткод: | 2FB07050 |
Деталь: | SPRING CURSOR |
Парткод: | 2FB07060 |
Деталь: | SIZE DETECTION ASSY |
Парткод: | 2FG01020 |
Деталь: | SHAFT, WORK PLATE |
Парткод: | 302AR07041 |
Деталь: | WORK PLATE,LIFT CASSETTE |
Парткод: | 302BC06091 |
Деталь: | PLATE SIZE C |
Парткод: | 302FB05200 |
Деталь: | PLATE SIZE IN |
Парткод: | 302FB05210 |
Деталь: | LEVER CURSOR A |
Парткод: | 302FB07032 |
Деталь: | LEVER CURSOR B |
Парткод: | 302FB07042 |
Деталь: | ADJUSTING PLATE CASSETTE |
Парткод: | 302FB07340 |
Деталь: | PIN CASSETTE |
Парткод: | 302FB07420 |
Деталь: | BASE CASSETTE |
Парткод: | 302FG07091 |
Деталь: | CURSOR C CASSETTE |
Парткод: | 302FG07151 |
Деталь: | FRONT GUIDE C,CURSOR |
Парткод: | 302FG07170 |
Деталь: | REAR GUIDE C,CURSOR |
Парткод: | 302FG07180 |
Деталь: | GROUND PLATE,CASSETTE |
Парткод: | 302FG07200 |
Деталь: | STOPPER,TRAILING EDGE DETECTION |
Парткод: | 302FG07230 |
Деталь: | CASSETTE |
Парткод: | 302GR09011 |
Деталь: | HANDLE CASSETTE 1 |
Парткод: | 302GR09020 |
Деталь: | COVER CASSETTE |
Парткод: | 302GR09030 |
Деталь: | HANDLE CASSETTE 2 |
Парткод: | 302GR09040 |
Деталь: | LEVER CASSETTE |
Парткод: | 302GR09051 |
Деталь: | RAIL CURSOR R |
Парткод: | 302GR09060 |
Деталь: | LID PAPER SIZE |
Парткод: | 302GR09070 |
Деталь: | RAIL CURSOR A |
Парткод: | 302GR09080 |
Деталь: | Support Plate |
Парткод: | 302GR09090 |
Деталь: | FRONT CURSOR CASSETTE |
Парткод: | 302GR09102 |
Деталь: | REAR CURSOR CASSETTE |
Парткод: | 302GR09112 |
Деталь: | SPRING LEVER CASSETTE |
Парткод: | 302GR09120 |
Деталь: | SHAFT PULLEY |
Парткод: | 302GR09130 |
Деталь: | SHAFT HANDLE |
Парткод: | 302GR09140 |
Деталь: | WORK PLATE HANDLE |
Парткод: | 302GR09150 |
Деталь: | STOPPER PAPER |
Парткод: | 302GR09160 |
Деталь: | PLATE SIZE INCH |
Парткод: | 302GR09201 |
Деталь: | SEAL DETECTION PLATE |
Парткод: | 302GR09210 |
Деталь: | SPACER SIZE PLATE |
Парткод: | 302GR09980 |
Деталь: | LIFT LOCK |
Парткод: | 302GR09990 |
Деталь: | LABEL CASSETTE OPERATION |
Парткод: | 302GR34011 |
Деталь: | LABEL PAPER SIZE |
Парткод: | 302GR34022 |
Деталь: | LABEL PAPER SIZE R |
Парткод: | 302GR34032 |
Деталь: | WIRE CASSETTE UNIT |
Парткод: | 302GR46450 |
Деталь: | DETECTION PLATE,PAPER SIZE |
Парткод: | 33907170 |
Деталь: | CUSHION,CASSETTE WORK PLATE |
Парткод: | 33907210 |
Деталь: | PULLEY,CASSETTE |
Парткод: | 34907150 |
Деталь: | PLATE NUMBER4 |
Парткод: | 3CF04060 |
Деталь: | RETAINER M4 |
Парткод: | 3CY06030 |
Деталь: | RACK CURSOR |
Парткод: | 3CY06090 |
Деталь: | GEAR 20,CURSOR |
Парткод: | 3CY06100 |
Деталь: | PLATE NUMBER 3 /3CF0405 A4 |
Парткод: | 5MVX321CE001 |
Деталь: | CUSHION,CASSETTE R |
Парткод: | 60907170 |
Деталь: | LABEL,PAPER UPPER LIMIT |
Парткод: | 61705110 |
Деталь: | SPRING, PAD |
Парткод: | 66106080 |
Деталь: | PAD,CASSETTE |
Парткод: | 66107100 |
Деталь: | CONNECTOR |
Парткод: | 7YCC08B2046+H01 |
Деталь: | CT-710 |
Парткод: | 302GR93082 |
Деталь: | STOPPER 6 |
Парткод: | 2BC06910 |
Деталь: | SPONGE WIRE A |
Парткод: | 2BG06500 |
Деталь: | BUSH 8 EW |
Парткод: | 2BG22950 |
Деталь: | BUSH 6 |
Парткод: | 2BG22960 |
Деталь: | ROLLER FEED LOW |
Парткод: | 302FZ22750 |
Деталь: | GUIDE FEED LOW 1ST |
Парткод: | 302FZ22800 |
Деталь: | SWITCH CONVEYING |
Парткод: | 302FZ44080 |
Деталь: | WIRE FEED SW UP |
Парткод: | 302FZ46540 |
Деталь: | SWITCH,SIZE |
Парткод: | 35927420 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | PLATE SENS MIDDLE |
Парткод: | 302FZ22940 |
Деталь: | GUIDE FEED LOW 2ND |
Парткод: | 302FZ22810 |
Деталь: | GUIDE FEED UP 2ND |
Парткод: | 302FZ22830 |
Деталь: | WIRE FEED SW LOW |
Парткод: | 302FZ46550 |
Деталь: | SWITCH REGISTRATION |
Парткод: | 302FZ44090 |
Деталь: | SENSOR 248NL1 |
Парткод: | 2C927210 |
Деталь: | GUIDE MIDDLE LOW |
Парткод: | 302FZ22591 |
Деталь: | SPRING EARTH MIDDLE |
Парткод: | 302FZ22630 |
Деталь: | STOPPER EARTH MIDDLE |
Парткод: | 302FZ22760 |
Деталь: | SHEET GUIDE LOW A |
Парткод: | 302FZ22781 |
Деталь: | SHEET GUIDE LOW B |
Парткод: | 302FZ22790 |
Деталь: | ACTUATOR MID BYPASS |
Парткод: | 302FZ22840 |
Деталь: | SPRING ACTUATOR BYPASS |
Парткод: | 302FZ22870 |
Деталь: | SHEET SENS MIDDLE |
Парткод: | 302FZ22950 |
Деталь: | WIRE FEED JAM |
Парткод: | 302FZ46330 |
Деталь: | CAM SHAFT BLADE |
Парткод: | 302FZ02671 |
Деталь: | SHAFT CLN LSU |
Парткод: | 302FZ02682 |
Деталь: | CUT WASHER 4 |
Парткод: | 2BG22990 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | CLUTCH LSU CLEANING |
Парткод: | 302FZ02741 |
Деталь: | ROLLER REGIST R |
Парткод: | 302FZ22040 |
Деталь: | GEAR REGIST Z18H |
Парткод: | 302FZ22120 |
Деталь: | BEARING 688AZZ |
Парткод: | 302FZ21300 |
Деталь: | LABEL JAM BYPASS B1 |
Парткод: | 302FZ07340 |
Деталь: | GUIDE FEED R |
Парткод: | 302FZ22084 |
Деталь: | SHAFT MIDDLE L |
Парткод: | 302FZ22140 |
Деталь: | PULLEY MIDDLE |
Парткод: | 302FZ22150 |
Деталь: | ACTUATOR REGIST |
Парткод: | 302FZ22160 |
Деталь: | SPRING MIDDLE |
Парткод: | 302FZ22341 |
Деталь: | SHEET REGIST |
Парткод: | 302FZ22380 |
Деталь: | SPRING ACTUATOR REGIST |
Парткод: | 302FZ22620 |
Деталь: | PLATE GUIDE MIDDLE R |
Парткод: | 302FZ24110 |
Деталь: | PAD REGIST |
Парткод: | 302FZ24160 |
Деталь: | PLATE GUIDE MIDDLE F |
Парткод: | 302FZ24220 |
Деталь: | Bush SP |
Парткод: | 302FZ24600 |
Деталь: | WIRE REG JAM |
Парткод: | 302FZ46350 |
Деталь: | SOLENOID LSU CLN |
Парткод: | 302FZ44050 |
Деталь: | BUSH 6 EW |
Парткод: | 2BG22970 |
Деталь: | GUIDE MIDDLE R |
Парткод: | 302FZ22060 |
Деталь: | SHEET MIDDLE BYPASS |
Парткод: | 302FZ22460 |
Деталь: | GEAR MIDDLE A |
Парткод: | 302FZ22470 |
Деталь: | GEAR MIDDLE B |
Парткод: | 302FZ22481 |
Деталь: | GEAR MIDDLE Z19S |
Парткод: | 302FZ22490 |
Деталь: | LEVER MIDDLE F |
Парткод: | 302FZ22500 |
Деталь: | LEVER MIDDLE R |
Парткод: | 302FZ22520 |
Деталь: | SPRING MID LEVER F |
Парткод: | 302FZ22600 |
Деталь: | SPRING MID LEVER R |
Парткод: | 302FZ22610 |
Деталь: | GUIDE MIDDLE BYPASS |
Парткод: | 302FZ22860 |
Деталь: | STOPPER MID |
Парткод: | 302FZ22980 |
Деталь: | BUSH TC EW |
Парткод: | 302FZ24090 |
Деталь: | PARTS,ROLLER MIDDLE R SP |
Парткод: | 302FZ94540 |
Деталь: | PARTS,ROLLER MIDDLE BYPASS SP |
Парткод: | 302FZ94550 |
Деталь: | PLATE EARTH MID SENS |
Парткод: | 302FZ22690 |
Деталь: | MOUNT SHAFT CAM |
Парткод: | 302FZ02700 |
Деталь: | GUIDE FEED UP 1ST |
Парткод: | 302FZ22820 |
Деталь: | STOPPER CORD |
Парткод: | 302FZ22700 |
Деталь: | MOUNT SOLENOID |
Парткод: | 302FZ02690 |
Деталь: | PARTS,GUIDE FEED LOW 1ST ASSY SP |
Парткод: | 302FZ94200 |
Деталь: | PARTS,GUIDE FEED LOW 2ND ASSY SP |
Парткод: | 302FZ94210 |
Деталь: | PARTS,GUIDE MIDDLE LOW ASSY SP |
Парткод: | 302FZ94220 |
Деталь: | PARTS GUIDE FEED R ASSY |
Парткод: | 302FZ93430 |
Деталь: | PARTS,GUIDE MIDDLE R ASSY SP |
Парткод: | 302FZ94240 |
Деталь: | CONTROLLER BOX |
Парткод: | 302FZ39010 |
Деталь: | PARTS PRINTED W.BOARD ENGINE ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ93453 |
Деталь: | PARTS PRINTED W.BOARD ENGINE (40/35ppm) |
Парткод: | 302JD93090 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210004++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610005++H01 |
Деталь: | SHIELD GASKET |
Парткод: | 7ZGSSTG31020H01 |
Деталь: | WIRE DRUM-DLP KY |
Парткод: | 302FZ46150 |
Деталь: | WIRE DRUM-DLP CM |
Парткод: | 302FZ46140 |
Деталь: | SHEET WIRE |
Парткод: | 302FZ39840 |
Деталь: | WIRE APC |
Парткод: | 302FZ46071 |
Деталь: | CORE 15-26X13 |
Парткод: | 2AV27440 |
Деталь: | FAN BOX COOLING |
Парткод: | 302FZ44040 |
Деталь: | WIRE JOB |
Парткод: | 302FZ46340 |
Деталь: | COVER CONTROLLER |
Парткод: | 302FZ39020 |
Деталь: | GUIDE CF |
Парткод: | 2DA26520 |
Деталь: | PLATE OPTION |
Парткод: | 2DD26070 |
Деталь: | RAIL OPTION A /B-05 CONT BOX A2 |
Парткод: | 302BL26211 |
Деталь: | PLATE CONTROLLER |
Парткод: | 302FZ39060 |
Деталь: | SCREW OP / M3 X 8 CRFREE A4 |
Парткод: | 5MMT263SN012++R |
Деталь: | RAIL OPTION B /B-05 CONT BOX A2 |
Парткод: | 5MVB743SL005 |
Деталь: | MEMORY MODULE |
Парткод: | 7NMDD256MA01H01 |
Деталь: | PARTS,PWB DIMM PRINTER ASSY SP |
Парткод: | 302JD94080 |
Деталь: | PARTS PRINTED W.BOARD CONTROL ASSY (25/25ppm) (32/25ppm) |
Парткод: | 302FZ93423 |
Деталь: | PARTS PRINTED W.BOARD CONTROL ASSY (32/32ppm) (40/35ppm) |
Парткод: | 302HC93012 |
Деталь: | PRINTED W.BOARD FAN |
Парткод: | 302FZ01300 |
Деталь: | VARISTOR TC ASSY |
Парткод: | 302FZ01310 |
Деталь: | BASE CONVEYING |
Парткод: | 302FZ22012 |
Деталь: | GUIDE CONVEYING |
Парткод: | 302FZ22071 |
Деталь: | GUIDE TC L |
Парткод: | 302FZ22090 |
Деталь: | GEAR TC Z24H |
Парткод: | 302FZ22110 |
Деталь: | GEAR REGIST Z22H |
Парткод: | 302FZ22130 |
Деталь: | SHAFT MIDDLE L |
Парткод: | 302FZ22140 |
Деталь: | PULLEY MIDDLE |
Парткод: | 302FZ22150 |
Деталь: | HOOK CONVEYING F |
Парткод: | 302FZ22170 |
Деталь: | HOOK CONVEYING R |
Парткод: | 302FZ22180 |
Деталь: | PLATE DISCHARGER |
Парткод: | 302FZ22201 |
Деталь: | HOLDER DISCHARGER |
Парткод: | 302FZ22211 |
Деталь: | CONTACT TRANSFER |
Парткод: | 302FZ22220 |
Деталь: | CONTACT DISCHARGE |
Парткод: | 302FZ22230 |
Деталь: | PLATE EARTH REGIST |
Парткод: | 302FZ22241 |
Деталь: | SPRING EARTH CONVEYING |
Парткод: | 302FZ22250 |
Деталь: | SPRING REGIST F |
Парткод: | 302FZ22300 |
Деталь: | SPRING REGIST R |
Парткод: | 302FZ22310 |
Деталь: | SPRING TRANSFER F |
Парткод: | 302FZ22320 |
Деталь: | SPRING TRANSFER R |
Парткод: | 302FZ22330 |
Деталь: | SPRING MIDDLE |
Парткод: | 302FZ22341 |
Деталь: | SPRING GUIDE TRANSFER |
Парткод: | 302FZ22350 |
Деталь: | SPRING CONVEYING F |
Парткод: | 302FZ22360 |
Деталь: | SPRING CONVEYING R |
Парткод: | 302FZ22370 |
Деталь: | GUIDE MIDDLE L |
Парткод: | 302FZ22400 |
Деталь: | HOLDER SENS FEED |
Парткод: | 302FZ22411 |
Деталь: | SPRING EARTH CONVEYING UNIT |
Парткод: | 302FZ22540 |
Деталь: | COVER PWB FEED |
Парткод: | 302FZ22551 |
Деталь: | BUSH REGIST |
Парткод: | 302FZ22560 |
Деталь: | SPRING CONTACT DISCHARGER |
Парткод: | 302FZ22570 |
Деталь: | SPRING LEFT CONV |
Парткод: | 302FZ22580 |
Деталь: | SHAFT HOOK CONVEYING |
Парткод: | 302FZ22660 |
Деталь: | SHEET MIDDLE L |
Парткод: | 302FZ22720 |
Деталь: | STOPPER EARTH MIDDLE |
Парткод: | 302FZ22760 |
Деталь: | LEVER CONVEYING |
Парткод: | 302FZ22880 |
Деталь: | COVER LEVER CONVEY |
Парткод: | 302FZ22890 |
Деталь: | SHAFT LEVER CONVEY |
Парткод: | 302FZ22900 |
Деталь: | STOPPER BUSH TRANSFER |
Парткод: | 302FZ22911 |
Деталь: | BUSH TRANSFER B F |
Парткод: | 302FZ22920 |
Деталь: | LABEL JAM FEED A1 |
Парткод: | 302FZ22960 |
Деталь: | SHEET SENS CONVEY |
Парткод: | 302FZ22991 |
Деталь: | SHEET REGIST L |
Парткод: | 302FZ24010 |
Деталь: | GUIDE TC UP |
Парткод: | 302FZ24100 |
Деталь: | SPACER TC GUIDE |
Парткод: | 302FZ24140 |
Деталь: | SHEET DISCHARGER |
Парткод: | 302FZ24240 |
Деталь: | PLATE CONV FAN |
Парткод: | 302FZ24500 |
Деталь: | DUCT CONV UP |
Парткод: | 302FZ24510 |
Деталь: | SEAL FAN CONV |
Парткод: | 302FZ24530 |
Деталь: | SPRING EARTH FAN |
Парткод: | 302FZ24540 |
Деталь: | SEAL FAN CONV B |
Парткод: | 302FZ24550 |
Деталь: | SHEET FAN PWD |
Парткод: | 302FZ24560 |
Деталь: | Bush SP |
Парткод: | 302FZ24600 |
Деталь: | FAN CONVEYING 40 |
Парткод: | 302FZ44070 |
Деталь: | SWITCH REGISTRATION |
Парткод: | 302FZ44090 |
Деталь: | WIRE TC GUIDE |
Парткод: | 302FZ46861 |
Деталь: | WIRE FEED J |
Парткод: | 302FZ46880 |
Деталь: | WIRE FEED PI |
Парткод: | 302FZ46890 |
Деталь: | PARTS,ROLLER TRANSFER SP |
Парткод: | 302FZ94510 |
Деталь: | PARTS,ROLLER REGIST L SP |
Парткод: | 302FZ94520 |
Деталь: | COLLAR TRANS ROLLER |
Парткод: | 302GR22110 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210006++H01 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | STOPPER BAND CONVEY |
Парткод: | 302FZ22770 |
Деталь: | BAND CONVEYING |
Парткод: | 302FZ24060 |
Деталь: | PARTS FEED UNIT ASSY |
Парткод: | 302FZ93510 |
Деталь: | PULLEY EXIT |
Парткод: | 2BG20320 |
Деталь: | PCB EJECT SW ASSY |
Парткод: | 2C901060 |
Деталь: | ARM LINK |
Парткод: | 2C921180 |
Деталь: | SENSOR 248NL1 |
Парткод: | 2C927210 |
Деталь: | SHAFT MIDDLE L |
Парткод: | 302FZ22140 |
Деталь: | PULLEY MIDDLE |
Парткод: | 302FZ22150 |
Деталь: | SHAFT EXIT PULLEY |
Парткод: | 302FZ25380 |
Деталь: | GEAR Z20S-Z23S |
Парткод: | 302FZ28060 |
Деталь: | GEAR Z23S EXIT |
Парткод: | 302FZ28080 |
Деталь: | GEAR Z29S |
Парткод: | 302FZ28090 |
Деталь: | SPRING EXIT PULLEY |
Парткод: | 302FZ28100 |
Деталь: | SPRING EXIT PULLEY A |
Парткод: | 302FZ28110 |
Деталь: | SPRING EARTH |
Парткод: | 302FZ28120 |
Деталь: | FRAME EXIT UPPER |
Парткод: | 302FZ28152 |
Деталь: | FRAME EXIT LOWER |
Парткод: | 302FZ28160 |
Деталь: | GUIDE CHANGE R |
Парткод: | 302FZ28171 |
Деталь: | ACTUATOR EXIT L |
Парткод: | 302FZ28180 |
Деталь: | SPRING ACTUATOR L |
Парткод: | 302FZ28200 |
Деталь: | SPRING ACTUATOR R |
Парткод: | 302FZ28210 |
Деталь: | SPRING LINK |
Парткод: | 302FZ28220 |
Деталь: | ACTUATOR EXIT R |
Парткод: | 302FZ28240 |
Деталь: | EARTH PLATE F/D |
Парткод: | 302FZ28250 |
Деталь: | EXIT PUSH |
Парткод: | 302FZ28260 |
Деталь: | SPRING EXIT PUSH |
Парткод: | 302FZ28270 |
Деталь: | SHEET SILENCER EXIT |
Парткод: | 302FZ28280 |
Деталь: | ACTUATOR EXIT SENSOR |
Парткод: | 302FZ28410 |
Деталь: | WIRE EXIT JAM SENSOR |
Парткод: | 302FZ46470 |
Деталь: | PARTS,ROLLER EXIT SP |
Парткод: | 302FZ94610 |
Деталь: | STATIC ELIMINATOR B,EJECT |
Парткод: | 34821210 |
Деталь: | BUSHING 6 |
Парткод: | 3CY07080 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | PARTS EXIT ASSY |
Парткод: | 302FZ93180 |
Деталь: | PARTS,MOTOR IMAGE SP |
Парткод: | 302JD94010 |
Деталь: | PLATE DRIVE TC |
Парткод: | 302JD31110 |
Деталь: | GEAR Z72L Z30L TC |
Парткод: | 302JD31240 |
Деталь: | CLUTCH REGIST 8 |
Парткод: | 302FZ31810 |
Деталь: | STOPPER 5 |
Парткод: | 2BC06980 |
Деталь: | WIRE REG CLT JOINT |
Парткод: | 302FZ46761 |
Деталь: | MOTOR LIFT |
Парткод: | 302GR44112 |
Деталь: | BUSHING 8 |
Парткод: | 2BC06510 |
Деталь: | STOPPER 6 |
Парткод: | 2BC06910 |
Деталь: | SPRING COUPLING DLP |
Парткод: | 2BG22530 |
Деталь: | MOTOR DLP |
Парткод: | 302FZ31030 |
Деталь: | SHAFT DLP DRIVE |
Парткод: | 302FZ31180 |
Деталь: | SHAFT CLN DRIVE |
Парткод: | 302FZ31190 |
Деталь: | COUPLING DLP DRIVE |
Парткод: | 302FZ31250 |
Деталь: | COLLAR DLP COUPLING |
Парткод: | 302FZ31280 |
Деталь: | GEAR Z22L DLP |
Парткод: | 302FZ31330 |
Деталь: | GEAR Z24R |
Парткод: | 302FZ31340 |
Деталь: | GEAR Z22R |
Парткод: | 302FZ31350 |
Деталь: | GEAR Z50L |
Парткод: | 302FZ31360 |
Деталь: | GEAR Z52R |
Парткод: | 302FZ31370 |
Деталь: | GEAR Z55L |
Парткод: | 302FZ31380 |
Деталь: | GEAR Z60L |
Парткод: | 302FZ31390 |
Деталь: | GEAR Z54L-Z26L |
Парткод: | 302FZ31401 |
Деталь: | GEAR Z28R |
Парткод: | 302FZ31600 |
Деталь: | PIN MAIN DRIVE |
Парткод: | 302FZ31720 |
Деталь: | GEAR Z22L CLN |
Парткод: | 302FZ31850 |
Деталь: | GEAR Z35L DLP |
Парткод: | 302FZ31890 |
Деталь: | HOLDER DRUM MOTOR |
Парткод: | 302FZ32051 |
Деталь: | SHEET DLP MOTOR |
Парткод: | 302FZ39800 |
Деталь: | HOLDER MAIN DRIVE |
Парткод: | 302JD31040 |
Деталь: | HOLDER DLP CL |
Парткод: | 302JD31070 |
Деталь: | PLATE MAIN DRIVE |
Парткод: | 302JD31080 |
Деталь: | SHAFT CLN DRIVE |
Парткод: | 302JD31120 |
Деталь: | SHAFT DLP K |
Парткод: | 302JD31130 |
Деталь: | SHAFT DLP CL |
Парткод: | 302JD31140 |
Деталь: | GEAR Z20R |
Парткод: | 302JD31150 |
Деталь: | GEAR Z31R CL |
Парткод: | 302JD31160 |
Деталь: | GEAR Z31L |
Парткод: | 302JD31170 |
Деталь: | GEAR Z32R |
Парткод: | 302JD31180 |
Деталь: | GEAR Z29R |
Парткод: | 302JD31190 |
Деталь: | SHEET MAIN DRIVE |
Парткод: | 302JD31250 |
Деталь: | PARTS,CLUTCH DLP 8 SP |
Парткод: | 302JD94020 |
Деталь: | PARTS,PWB MOTOR DRIVER ASSY SP |
Парткод: | 302JD94090 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | BUSH 6 |
Парткод: | 2BG22960 |
Деталь: | SHAFT MPF CL |
Парткод: | 302FZ31160 |
Деталь: | SHAFT BYPASS DRIVE |
Парткод: | 302FZ31220 |
Деталь: | SHAFT BRS DRIVE |
Парткод: | 302FZ31230 |
Деталь: | GEAR Z38R MPF |
Парткод: | 302FZ31300 |
Деталь: | GEAR Z24R BRS |
Парткод: | 302FZ31310 |
Деталь: | GEAR Z20S BRS |
Парткод: | 302FZ31320 |
Деталь: | GEAR Z26L BYPASS |
Парткод: | 302FZ31540 |
Деталь: | GEAR Z27S BYPASS |
Парткод: | 302FZ31550 |
Деталь: | PIN MPF DRIVE |
Парткод: | 302FZ31710 |
Деталь: | CLUTCH FEED 6 |
Парткод: | 302FZ31820 |
Деталь: | SEAL MPF CL |
Парткод: | 302FZ32060 |
Деталь: | HOLDER MPF DRIVE |
Парткод: | 302JD31060 |
Деталь: | PLATE MPF DRIVE |
Парткод: | 302JD31100 |
Деталь: | GEAR Z85L-Z47R MPF |
Парткод: | 302JD31220 |
Деталь: | GEAR Z86L Z39L MPF |
Парткод: | 302JD31230 |
Деталь: | BUSHING 6 |
Парткод: | 3CY07080 |
Деталь: | CUT WASHER |
Парткод: | 5MVS665KB001 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | PARTS MOTOR DRUM |
Парткод: | 302JD93130 |
Деталь: | JOINT DRUM |
Парткод: | 302FZ31270 |
Деталь: | STOPPER D MOTOR |
Парткод: | 302FZ31990 |
Деталь: | WIRE DLP MOTOR |
Парткод: | 302FZ46081 |
Деталь: | WIRE DRUM MOTOR SIG |
Парткод: | 302JD46040 |
Деталь: | WIRE LIFT MOT |
Парткод: | 302FZ46250 |
Деталь: | WIRE DRM MOT A |
Парткод: | 302JD46050 |
Деталь: | CORE 8-16X10 |
Парткод: | 3HK27050 |
Деталь: | WIRE TRNS MOT JOINT |
Парткод: | 302JD46130 |
Деталь: | BEARING PRESS ROLLER |
Парткод: | 2FG20310 |
Деталь: | SPRING JOINT D |
Парткод: | 302BG22021 |
Деталь: | PARTS MAIN DRIVE ASSY |
Парткод: | 302JD93030 |
Деталь: | PARTS MPF DRIVE ASSY |
Парткод: | 302JD93020 |
Деталь: | GEAR Z38R DSK |
Парткод: | 302FZ31520 |
Деталь: | PULLEY 26 FEED |
Парткод: | 302FZ31730 |
Деталь: | BELT FEED DRIVE |
Парткод: | 302FZ31260 |
Деталь: | WIRE JOINT |
Парткод: | 302FZ46020 |
Деталь: | BUSH 6 |
Парткод: | 2BG22960 |
Деталь: | BUSH 8 |
Парткод: | 2BG22980 |
Деталь: | MOTOR FEED |
Парткод: | 302FZ31020 |
Деталь: | HOLDER CLUTCH |
Парткод: | 302FZ31170 |
Деталь: | SHAFT FEED DRIVE |
Парткод: | 302FZ31200 |
Деталь: | SHAFT FEED 2 DRIVE |
Парткод: | 302FZ31210 |
Деталь: | SHAFT LSU DRIVE |
Парткод: | 302FZ31240 |
Деталь: | GEAR Z42L |
Парткод: | 302FZ31430 |
Деталь: | GEAR Z14R LSU |
Парткод: | 302FZ31440 |
Деталь: | GEAR Z36L-Z22R REG |
Парткод: | 302FZ31450 |
Деталь: | GEAR Z52L LSU |
Парткод: | 302FZ31460 |
Деталь: | GEAR Z33R-Z23R CL |
Парткод: | 302FZ31470 |
Деталь: | GEAR Z33R-Z23R FEED |
Парткод: | 302FZ31480 |
Деталь: | GEAR Z28L |
Парткод: | 302FZ31490 |
Деталь: | GEAR Z32L-Z26R FEED CL |
Парткод: | 302FZ31500 |
Деталь: | GEAR Z26R-Z23L FEED CL |
Парткод: | 302FZ31510 |
Деталь: | GEAR Z32L |
Парткод: | 302FZ31530 |
Деталь: | GEAR Z35L CL |
Парткод: | 302FZ31590 |
Деталь: | GEAR Z28R |
Парткод: | 302FZ31600 |
Деталь: | PIN DRIVE FEED |
Парткод: | 302FZ31740 |
Деталь: | GEAR Z25R JOINT |
Парткод: | 302FZ31800 |
Деталь: | CLUTCH REGIST 8 |
Парткод: | 302FZ31810 |
Деталь: | CLUTCH FEED 6 |
Парткод: | 302FZ31820 |
Деталь: | STUD SCREW 435 |
Парткод: | 302FZ31840 |
Деталь: | COUPLING PAPER FEED |
Парткод: | 302FZ32070 |
Деталь: | PLATE EARTH FEED |
Парткод: | 302FZ39720 |
Деталь: | WIRE PRE FEED |
Парткод: | 302FZ46100 |
Деталь: | PARTS,PWB FEED ASSY,SP |
Парткод: | 302FZ94681 |
Деталь: | HOLDER FEED DRIVE |
Парткод: | 302JD31050 |
Деталь: | PLATE FEED DRIVE |
Парткод: | 302JD31090 |
Деталь: | GEAR Z70L Z26R FEED |
Парткод: | 302JD31200 |
Деталь: | GEAR Z33L FEED |
Парткод: | 302JD31210 |
Деталь: | CUT WASHER |
Парткод: | 5MVS665KB001 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | CONNECTOR |
Парткод: | 7YCC08B2046+H02 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210006++H01 |
Деталь: | ACCESS.BAND |
Парткод: | 7YZM410001++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | WIRE TRANSFER |
Парткод: | 302FZ46050 |
Деталь: | COLLAR EJECT |
Парткод: | 3HL10170 |
Деталь: | COLLAR DU PULLEY |
Парткод: | 302FZ29140 |
Деталь: | WIRE EXIT MOT |
Парткод: | 302FZ46411 |
Деталь: | BUSHING 8 |
Парткод: | 2BC06510 |
Деталь: | STOPPER 5 |
Парткод: | 2BC06980 |
Деталь: | GEAR Z20L FUSER DRIVE |
Парткод: | 302FZ31570 |
Деталь: | GEAR Z46 FUSER |
Парткод: | 302FZ31580 |
Деталь: | JOINT GEAR EXIT |
Парткод: | 302FZ31671 |
Деталь: | PULLEY EXIT DRIVE |
Парткод: | 302FZ31680 |
Деталь: | GEAR EXIT Z20 |
Парткод: | 302FZ31690 |
Деталь: | GEAR EXIT Z63 Z21 |
Парткод: | 302FZ31700 |
Деталь: | PIN EXIT |
Парткод: | 302FZ31750 |
Деталь: | GEAR EXIT Z39Z26 |
Парткод: | 302FZ31760 |
Деталь: | GEAR EXIT Z30 JOINT |
Парткод: | 302FZ31770 |
Деталь: | GEAR EXIT Z48 |
Парткод: | 302FZ31780 |
Деталь: | SPRING EXIT 60 |
Парткод: | 302FZ31790 |
Деталь: | MOUNT FUSER DRIVE |
Парткод: | 302FZ31861 |
Деталь: | GEAR Z20 FUSER |
Парткод: | 302FZ31870 |
Деталь: | GEAR EXIT Z45Z22 |
Парткод: | 302FZ31910 |
Деталь: | GEAR Z30 FUSER |
Парткод: | 302FZ31920 |
Деталь: | GEAR Z65-Z29 FUSER |
Парткод: | 302FZ31930 |
Деталь: | PLATE FUSER DRIVE |
Парткод: | 302FZ32010 |
Деталь: | HOLDER FUSER CL |
Парткод: | 302FZ32021 |
Деталь: | SHAFT FUSER DRIVE |
Парткод: | 302FZ32030 |
Деталь: | CLUTCH FUSER 8 |
Парткод: | 302FZ32040 |
Деталь: | PARTS,MOTOR FUSER SP |
Парткод: | 302FZ94290 |
Деталь: | SW.MICRO |
Парткод: | 7SM010303+++H01 |
Деталь: | PARTS FEED DRIVE ASSY |
Парткод: | 302JD93040 |
Деталь: | PARTS FUSER DRIVE ASSY |
Парткод: | 302FZ93270 |
Деталь: | PULLEY,SEPARATION |
Парткод: | 2AR07230 |
Цена: | 360 ₽ |
Деталь: | BUSH 6 |
Парткод: | 2BG22960 |
Деталь: | BUSH 6 EW |
Парткод: | 2BG22970 |
Деталь: | TORQUE LIMITER 340 |
Парткод: | 2C907280 |
Деталь: | SENSOR 248NL1 |
Парткод: | 2C927210 |
Деталь: | JOINT DRIVE |
Парткод: | 302FB06151 |
Деталь: | PAD MP |
Парткод: | 302FB17760 |
Деталь: | SOLENOID LEADING FEED |
Парткод: | 302FB25180 |
Деталь: | BASE MPT |
Парткод: | 302FZ08011 |
Деталь: | LOWER GUIDE MPT |
Парткод: | 302FZ08020 |
Деталь: | SHAFT FEED MPT |
Парткод: | 302FZ08030 |
Деталь: | SHAFT FEED JOINT MPT |
Парткод: | 302FZ08040 |
Деталь: | SHAFT SEPARATE MPT |
Парткод: | 302FZ08050 |
Деталь: | HOLDER MPT LF |
Парткод: | 302FZ08070 |
Деталь: | PAPER STOPPER MPT F |
Парткод: | 302FZ08090 |
Деталь: | PAPER STOPPER MPT R |
Парткод: | 302FZ08100 |
Деталь: | LEVER STOPPER RELEASE |
Парткод: | 302FZ08110 |
Деталь: | SPRING SEPARATE PULLEY |
Парткод: | 302FZ08120 |
Деталь: | PULLEY LEADING FEED MPT |
Парткод: | 302FZ08130 |
Деталь: | HOLDER SEPARATE MPT |
Парткод: | 302FZ08160 |
Деталь: | GEAR MPT Z23 |
Парткод: | 302FZ08180 |
Деталь: | SPRING HOLDER MPT |
Парткод: | 302FZ08190 |
Деталь: | SPRING MID MPT |
Парткод: | 302FZ08291 |
Деталь: | GEAR MPT Z41Z35 |
Парткод: | 302FZ08300 |
Деталь: | ACTUATOR MIDDLE MPT |
Парткод: | 302FZ08310 |
Деталь: | LEVER MPT SOLENOID |
Парткод: | 302FZ08320 |
Деталь: | SPRING ACTUATOR MPT |
Парткод: | 302FZ08350 |
Деталь: | COVER MPT DRIVE |
Парткод: | 302FZ08360 |
Деталь: | GEAR JOINT MPT UNIT |
Парткод: | 302FZ08370 |
Деталь: | SPRING SOLENOID MPT |
Парткод: | 302FZ08430 |
Деталь: | PLATE EARTH MPT ROLL |
Парткод: | 302FZ08440 |
Деталь: | GEAR MPT FEED Z19 ASSY |
Парткод: | 302FZ08450 |
Деталь: | PAD WIRE |
Парткод: | 302FZ08460 |
Деталь: | SHAFT MIDDLE L |
Парткод: | 302FZ22140 |
Деталь: | PULLEY MIDDLE |
Парткод: | 302FZ22150 |
Деталь: | Bush SP |
Парткод: | 302FZ24600 |
Деталь: | CLUTCH MPF 6 |
Парткод: | 302FZ31830 |
Деталь: | WIRE MPF UNIT |
Парткод: | 302FZ46520 |
Деталь: | PARTS,ROLLER MID MPT SP |
Парткод: | 302FZ94490 |
Деталь: | FRICTION PLATE,BYPASS |
Парткод: | 33906400 |
Деталь: | RING STOPPER 4 |
Парткод: | 5MVL177DN001 |
Деталь: | BUSH D1234 |
Парткод: | 5MVM176XN001 |
Деталь: | RING STOPPER /A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | PARTS MPT ASSY |
Парткод: | 302FZ93220 |
Деталь: | PARTS FUSER 120 ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ93165 |
Деталь: | PARTS FUSER 120 ASSY (40/35ppm) |
Парткод: | 302JD93050 |
Деталь: | PARTS FUSER 200 ASSY (25/25ppm) (32/25ppm) (32/32ppm) |
Парткод: | 302FZ93174 |
Деталь: | PARTS FUSER 200 ASSY (40/35ppm) |
Парткод: | 302JD93060 |
Деталь: | PARTS FUSER 110 ASSY |
Парткод: | 302FZ93533 |
Деталь: | ACCESS.BUSHING |
Парткод: | 7YZM110004++H01 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610008++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210003++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610002++H01 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210002++H01 |
Деталь: | RAIL IMAGE REAR |
Парткод: | 302FZ02160 |
Деталь: | STOPPER IMAGE UNIT R |
Парткод: | 302FZ02291 |
Деталь: | SPRING STOPPER |
Парткод: | 302FZ02300 |
Деталь: | PAD WIRE A |
Парткод: | 302FZ39890 |
Деталь: | THERMISTOR |
Парткод: | 302FZ45120 |
Деталь: | CONNECTOR |
Парткод: | 7YCC02B1001+H01 |
Деталь: | RAIL IMAGE FRONT |
Парткод: | 302FZ02150 |
Деталь: | STOPPER IMAGE UNIT F |
Парткод: | 302FZ02280 |
Деталь: | WIRE ID SENSOR |
Парткод: | 302FZ46040 |
Деталь: | HOOK DLP |
Парткод: | 302FZ02591 |
Деталь: | FELT TC CLN |
Парткод: | 2BG16590 |
Деталь: | RAIL DRUM LEFT |
Парткод: | 302FZ02170 |
Деталь: | SHUTTER ID SENSOR |
Парткод: | 302FZ02190 |
Деталь: | SPRING SHUTTER ID SENSOR |
Парткод: | 302FZ02200 |
Деталь: | GUIDE TC R |
Парткод: | 302FZ02710 |
Деталь: | PLATE ID SENSOR |
Парткод: | 302FZ02770 |
Деталь: | SHEET ID SENSOR |
Парткод: | 302FZ02780 |
Деталь: | SHEET TRANSFER R |
Парткод: | 302FZ24020 |
Деталь: | ID SENSOR |
Парткод: | 302FZ45080 |
Деталь: | WIRE ID SENSOR UNIT |
Парткод: | 302FZ46321 |
Деталь: | BRACKET MPT GEAR |
Парткод: | 302FZ07500 |
Деталь: | GEAR JOINT MPT |
Парткод: | 302FZ07510 |
Деталь: | STOPPER 5 |
Парткод: | 2BC06980 |
Деталь: | PRINTED W. BOARD TONER FULL ASSY |
Парткод: | 302FZ01280 |
Деталь: | RETAINER PU |
Парткод: | 302FZ02120 |
Деталь: | LEVER RETAINER |
Парткод: | 302FZ02410 |
Деталь: | SPRING RETAINER |
Парткод: | 302FZ02420 |
Деталь: | SHAFT SWEEP DRIVE |
Парткод: | 302FZ02810 |
Деталь: | GEAR SWEEP Z15 |
Парткод: | 302FZ02820 |
Деталь: | GEAR SWEEP Z23 |
Парткод: | 302FZ02830 |
Деталь: | GEAR SWEEP Z49 Z24 |
Парткод: | 302FZ02840 |
Деталь: | GEAR SWEEP Z28 |
Парткод: | 302FZ02850 |
Деталь: | SHAFT FEED SWEEP |
Парткод: | 302FZ02860 |
Деталь: | GEAR SWEEP Z20 |
Парткод: | 302FZ02870 |
Деталь: | PLATE DRUM EARTH |
Парткод: | 302FZ02900 |
Деталь: | TAPE RETAINER |
Парткод: | 302FZ02910 |
Деталь: | SHEET TRAY CL |
Парткод: | 302FZ02920 |
Деталь: | SHEET TRAY BK |
Парткод: | 302FZ02930 |
Деталь: | COVER INNER MIDDLE |
Парткод: | 302FZ04510 |
Деталь: | TRAY CONTAINER Y |
Парткод: | 302FZ04540 |
Деталь: | TRAY CONTAINER BK |
Парткод: | 302FZ04550 |
Деталь: | COVER FULL SENSOR |
Парткод: | 302FZ04571 |
Деталь: | TRAY CONTAINER M |
Парткод: | 302FZ04590 |
Деталь: | TRAY CONTAINER C |
Парткод: | 302FZ04600 |
Деталь: | LEVER LOCK WASTE |
Парткод: | 302FZ04780 |
Деталь: | SPRING LOCK WASTE |
Парткод: | 302FZ04790 |
Деталь: | SEAL TRAY BK |
Парткод: | 302FZ04890 |
Деталь: | SEAL TRAY Y |
Парткод: | 302FZ04900 |
Деталь: | SEAL TRAY C |
Парткод: | 302FZ04910 |
Деталь: | SEAL TRAY M |
Парткод: | 302FZ04920 |
Деталь: | TRAY WASTE |
Парткод: | 302FZ04940 |
Деталь: | SPONGE TRAY WASTE |
Парткод: | 302FZ04950 |
Деталь: | WIRE WASTE TONER SENSOR |
Парткод: | 302FZ46310 |
Деталь: | WIRE TONER SENSOR JOINT |
Парткод: | 302FZ46710 |
Деталь: | BUSHING 6 |
Парткод: | 3CY07080 |
Деталь: | PLATE WASTE SENSOR /A-80 A3 |
Парткод: | 5MMX321LD039 |
Деталь: | SPACER LED /43587J2063 A4 |
Парткод: | 5MVS313SB002 |
Деталь: | TRANSISTOR PHOTO PT491FE0000F |
Парткод: | 7QPPT491F+++H01 |
Деталь: | STOPPER CONTAINER CC |
Парткод: | 302FZ02470 |
Деталь: | STOPPER CONTAINER CB |
Парткод: | 302FZ02450 |
Деталь: | STOPPER CONTAINER BK CC |
Парткод: | 302FZ02480 |
Деталь: | STOPPER CONTAINER BK CB |
Парткод: | 302FZ02460 |
Деталь: | PARTS,ID SENSOR ASSY SP |
Парткод: | 302FZ94330 |
Деталь: | PARTS MPT JOINT ASSY |
Парткод: | 302FZ93230 |
Деталь: | RETAINER PU ASSY |
Парткод: | 302FZ00531 |
Коды ошибок
C0030
C0070
C0100
C0110
C0150
C0160
C0170
C0180
C0210
C0220
C0240
C0250
C0280
C0410
C0420
C0440
C0610
C0630
C0640
C0820
C0830
C0840
C0860
C0870
C0880
C0890
C0920
C1010
C1020
C1030
C1040
C1100
C1110
C1120
C1130
C1900
C1950
C2101
C2102
C2201
C2202
C2203
C2204
C2300
C2400
C2500
C2600
C2810
C3100
C3200
C3300
C3500
C3900
C3910
C4000
C4010
C4100
C4200
C5101
C5102
C5103
C5104
C5301
C5302
C5303
C5304
C6000
C6010
C6020
C6030
C6050
C6100
C6120
C6130
C6400
C7000
C7101
C7102
C7103
C7104
C7200
C7210
C7220
C7230
C7240
C7250
C7401
C7402
C7403
C7404
C7411
C7412
C7413
C7414
C7420
C7800
C7810
C7901
C7902
C7903
C7904
C7911
C7912
C7913
C7914
C8020
C8030
C8050
C8060
C8070
C8140
C8170
C8180
C8210
C8220
C8230
C8300
C8310
C8320
C8330
C8340
C8350
C8360
C8440
C8460
C8500
C8510
C8900
C8910
C8920
C8930
C9060
C9500 ... C9550
Описание
Error code: | C0030 |
Description: | FAX PWB system error |
Causes: | The FAX processing cannot be continued due to the FAX firmware error. |
Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. |
Error code: | C0070 |
Description: | Toner motor |
Causes: | Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
Remedy: | 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
Error code: | C0100 |
Description: | Charge corona winding problem |
Causes: | An abnormal status is output from the flash memory. |
Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. If not repaired, replace the main PWB. |
Error code: | C0110 |
Description: | Backup memory data problem (main PWB) • Data in the specified area of the backup memory does not match the specified values. |
Causes: | Problem with the backup memory data. Defective main PWB. |
Remedy: | Problem with the backup memory data. Run maintenance item U021 to set the contents of the backup memory data again. Defective main PWB. If the C0110 is displayed after initializing the backup memory, replace the main PWB and check for correct operation. |
Error code: | C0150 |
Description: | Engine EEPROM reading / writing error |
Causes: | 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing data. 2. The data read reading in 2 points mismatches 8 times continuously. 3. The read data and the write data mismatch 8 times continuously. |
Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C0160 |
Description: | Engine PWB EEPROM data error |
Causes: | The data read from the EEPROM is judged as abnormal. |
Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing U021 The storage data in the EEPROM on the engine PWB is faulty. Execute U021. Executing U021 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. |
Error code: | C0170 |
Description: | Charger count error |
Causes: | The values in one of the billing counters, life counter or the scanner counter mismatch between the main side and the engine side. |
Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. Detaching and reattaching the main PWB 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C0180 |
Description: | Machine serial number mismatch |
Causes: | The machine serial Nos. in the main PWB and the EEPROM on the engine PWB mismatch when turning the power on. |
Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. Executing U004 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C0210 |
Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
Error code: | C0220 |
Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and scanner CPU. |
Causes: | Defective main PWB. Poor contact in the connector terminals. Defective scanner PWB. |
Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC2 on the engine PWB and YC5 on the scanner PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective scanner PWB. Replace the scanner PWB. |
Error code: | C0240 |
Description: | Printer board* communication problem • The printer board does not respond 120 seconds after the power is turned on. |
Causes: | Poor contact in the connector terminals. DIMM installed incorrectly. Defective main PWB or printer board. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC9 on the main PWB and YC5 on the printer board, and the continuity across the connector terminals. Repair or replace if necessary. DIMM installed incorrectly. Check the connection. Repair or replace if necessary. Defective main PWB or printer board. Replace the main PWB or printer board and check for correct operation. |
Error code: | C0250 |
Description: | Network scanner board* communication problem • The response to the alive command to the network scanner transmitted once to 30 s does not come on the contrary three consecutive times or more. • The response to the communication command transmitted to the network scanner does not return 75 s or more. |
Causes: | Poor contact in the connector terminals. Defective main PWB or network scanner board. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the main PWB and the connector on the network scanner board, and the continuity across the connector terminals. Repair or replace if necessary. Defective main PWB or network scanner board. Replace the main PWB or network scanner board and check for correct operation. |
Error code: | C0280 |
Description: | Communication problem between the fax control PWB and main PWB Communication between the fax control PWB and the main PWB of the machine cannot be performed normally. |
Causes: | Poor contact in the connector terminals. Defective PWB. |
Remedy: | Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective PWB. Replace the fax control PWB or main PWB and check for correct operation. |
Error code: | C0410 |
Description: | Exposure lamp on too long |
Causes: | Poor contact in the connector terminals. Defective DP main PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 on the scanner PWB and YC1 on the DP main PWB, and the continuity across the connector terminals. Repair or replace if necessary Defective DP main PWB. Replace the DP main PWB and check for correct operation. |
Error code: | C0420 |
Description: | Side feeder* communication error • A communication error from side feeder is detected 10 times in succession. |
Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective side feeder main PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC15 on the engine PWB and the connector YC3 on the side feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective side feeder main PWB. Replace the side feeder main PWB. |
Error code: | C0440 |
Description: | Document finisher communication problem • A communication error from document finisher is detected 10 times in succession. |
Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective finisher main PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC14 on the engine PWB and YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective finisher main PWB. Replace the finisher main PWB. |
Error code: | C0610 |
Description: | Lens drive problem |
Causes: | Defective main PWB. |
Remedy: | Replace the main PWB and check for correct operation. |
Error code: | C0630 |
Description: | DMA error |
Causes: | DMA transmission of the image data does not finish within the certain time. |
Remedy: | 1 Checking the connection 0 0 2 Checking the connection 0 0 3 Replacing the wire The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • DPCIS - DP relay PWB • DP relay PWB - Main PWB Wiring diagram 4 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. Detaching and reattaching the DP relay PWB 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
Error code: | C0640 |
Description: | Hard Disk error |
Causes: | The HDD cannot be accessed properly. |
Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
Error code: | C0820 |
Description: | Fax control PWB CG ROM checksum error (optional fax) A checksum error occurred with the CG ROM data of the fax control PWB. |
Causes: | Defective fax software. Defective fax control PWB. |
Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
Error code: | C0830 |
Description: | FAX PWB flash program area checksum error |
Causes: | The program stored in the flash memory on the FAX PWB is broken so it cannot perform. |
Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 2 Checking the FAX PWB The FAX PWB is not properly connected. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
Error code: | C0840 |
Description: | RTC error ("Time for maintenance T" appears) |
Causes: | [Check at start-up] • RTC values are old. • Power has not been turned on for over 5 years. • RTC value is older than 2000/1/1 00:01. [Periodic check per 5 minutes after start-up] • RTC values are older than the ones at the last check. • Partial operation by power reset after C840 error and "Time for Maintenance T" is indicated. |
Remedy: | 1 Executing U906 The backup battery on the main PWB is faulty, and so, the RTC settings are erased after unplugging the power cord. Execute U906 to reset the display [Maintenance T]. After that, set the date/time (RTC) in the System menu. (It is necessary to execute this process whenever to unplug/plug the power cord.) Executing U906 2 Replacing the main PWB The main PWB is faulty, or the backup battery runs out. If service call error C0840 frequently appears after performing the previous step, replace the main PWB. Detaching and reattaching the main PWB |
Error code: | C0860 |
Description: | Fax control PWB software switch checksum error (optional fax) A checksum error occurred with the software switch value of the fax control PWB. |
Causes: | Defective fax software. Defective fax control PWB. |
Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
Error code: | C0870 |
Description: | PC FAX Image data transmission error |
Causes: | Data was not properly transmitted even if the specified times of retry were made when the large volume data is transmitted between the FAX PWB and the main PWB. |
Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 3 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 6 Executing U024 The data stored in the SSD is faulty. Execute U024 [SSD Format]. Executing U024 |
Error code: | C0880 |
Description: | Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed. |
Causes: | Defective fax software. Defective fax control PWB. |
Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
Error code: | C0890 |
Description: | Fax control PWB CG FONT archive problem (optional fax) When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed. |
Causes: | Defective fax software. Defective fax control PWB. |
Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
Error code: | C0920 |
Description: | 1st drawer lift |
Causes: | The backup data could not be stored since the file system of the flash memory is faulty. |
Remedy: | 1 Initializing the fax FAX control values are incorrect Execute U600 to initialize the FAX. Executing U600 2 Checking the FAX PWB The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Reinstalling the FAX PWB The FAX PWB is not properly installed. Reinstall the FAX PWB. FAX Installation Guide 4 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 5 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
Error code: | C1010 |
Description: | Lift motor 1 error |
Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C1020 |
Description: | Lift motor 2 error |
Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C1030 |
Description: | Lift motor 3 error • When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on. This error is detected four times successively. • During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on. This error is detected four times successively. |
Causes: | Broken gears or couplings of lift motor 3. Defective lift motor 3. Poor contact of lift motor 3 connector terminals. Defective lift limit switch 3. Poor contact of lift limit switch 3 connector terminals. Defective casette PWB. |
Remedy: | Broken gears or couplings of lift motor 3. Replace lift motor 3. Defective lift motor 3. Check for continuity across the coil. If none, replace lift motor 3. Poor contact of lift motor 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 3. Run maintenance item U031 and turn lift limit switch 3 on and off manually. Replace lift limit switch 3 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB |
Error code: | C1040 |
Description: | Lift motor 4 error • When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on. This error is detected four times successively. • During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on. This error is detected four times successively. |
Causes: | Broken gears or couplings of lift motor 4. Defective lift motor 4. Poor contact of lift motor 4 connector terminals. Defective lift limit switch 4. Poor contact of lift limit switch 4 connector terminals. Defective casette PWB. |
Remedy: | Broken gears or couplings of lift motor 4. Replace lift motor 4. Defective lift motor 4. Check for continuity across the coil. If none, replace lift motor 4. Poor contact of lift motor 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 4. Run maintenance item U031 and turn lift limit switch 4 on and off manually. Replace lift limit switch 4 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB. |
Error code: | C1100 |
Description: | PF lift motor 1 error |
Causes: | [The right cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because one of the phenomena below. 1. PF lift sensor 1 does not turn on when passing 23s while PF lift motor 1 turns on for the first time after inserting the cassette. 2. PF lift sensor 1 does not turn on when passing 2s while PF lift motor 1 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 1 is operating. |
Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 1 - PF main PWB Wiring diagram 4 Checking PF lift motor 1 PF lift motor 1 is faulty. Replace PF lift motor 1. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift sensor 1 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 1 is not properly attached or faulty. Reattach PF lift sensor 1. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
Error code: | C1110 |
Description: | PF lift motor 2 error |
Causes: | [The left cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because of one of the phenomena below. 1. PF lift sensor 2 does not turn on when passing 23s while PF lift motor 2 turns on for the first time after inserting the cassette. 2. PF lift sensor 2 does not turn on when passing 2s while PF lift motor 2 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 2 is operating. |
Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 2 - PF main PWB Wiring diagram 4 Replacing PF lift motor 2 PF lift motor 2 is faulty. Replace PF lift motor 2. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •PF lift sensor 2 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 2 is not properly attached or faulty. Reattach PF lift sensor 2. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
Error code: | C1120 |
Description: | PF left lift position problem (optional 3000-sheet paper feeder) Level switch 1 does not turn on within 30 s of PF lift motor 2 turning on. |
Causes: | Poor contact in the connector terminals. Defective level switch 1. Defective PF lift motor 2. The PF left lift does not rise properly. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 1. Check if YC5-4 on the PF main PWB goes low when level switch 1 is turned off. If not, replace PF lift switch 1. Defective PF lift motor 1. Check for continuity across the coil. If none, replace PF lift motor 1. The PF left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
Error code: | C1130 |
Description: | PF right lift position problem (optional 3000-sheet paper feeder) Level switch 2 does not turn on within 30 s of PF lift motor 1 turning on. |
Causes: | Poor contact in the connector terminals. Defective level switch 2. Defective PF lift motor 1. The PF right lift does not rise properly. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 2. Check if YC5-7 on the PF main PWB goes low when level switch 2 is turned off. If not, replace PF lift switch 2. Defective PF lift motor 2. Check for continuity across the coil. If none, replace PF lift motor 2. The PF right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
Error code: | C1900 |
Description: | Large capacity feeder EEPROM error Condition: When outputting Event Log after turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error is not recorded. (It is caused by the large capacity feeder.) (For the internal count) |
Causes: | The writing data and the reading data mismatch 3 times continuously when writing. |
Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C1950 |
Description: | Primary transfer belt unit EEPROM error |
Causes: | The EEPROM cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data do not match 8 times continuously. |
Remedy: | 1 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed or the connector is not connected. Reinstall the primary transfer belt unit and reconnect the connector. Detaching and reattaching the primary transfer belt unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 3 Primary transfer belt unit replacement The primary transfer belt unit is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C2101 |
Description: | Developer motor error |
Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor is stable. |
Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking the developer motor The developer motor drive is faulty. Execute U030 [DLP(K)] and check the developer motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 5 Checking the developer motor The developer motor is not properly attached or faulty. Reattach the developer motor. If not repaired, replace the motor. Detaching and reattaching the developer motor 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C2102 |
Description: | Developer motor C error |
Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor C drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor C is stable. |
Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking developer motor C The developer motor C drive is faulty. Execute U030 [DLP(C)] and check the developer motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 5 Checking developer motor C Developer motor C is not properly attached or faulty. Reattach developer motor C. If not repaired, replace the motor. Detaching and reattaching the main drive unit 6 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C2201 |
Description: | Drum motor steady-state error |
Causes: | The ready signal is at the H level for 1s continuously after the drum motor became stable. |
Remedy: | 1 Checking the drum motor The drum motor drive is faulty. Execute U030 [Process] and check the drum motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 4 Checking the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C2202 |
Description: | Drum motor C steady-state error |
Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB C at every 1s. |
Remedy: | 1 Checking drum motor C The drum motor C drive is faulty. Execute U030 [Process] and check the drum motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C2203 |
Description: | Drum motor M steady-state error |
Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB M at every 1s. |
Remedy: | 1 Checking drum motor M The drum motor M drive is faulty. Execute U030 [Process] and check the drum motor M operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor M - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C2204 |
Description: | Drum motor Y steady-state error |
Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB Y at every 1s. |
Remedy: | 1 Checking drum motor Y The drum motor Y drive is faulty. Execute U030 [Process] and check the drum motor Y operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor Y - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C2300 |
Description: | Fuser motor error |
Causes: | 1. The ready signal is at the H level for 1s continuously during the fuser motor drive. 2. The ready signal is not at the L level (stable rotation) when passing 2s after the fuser motor drive starts. |
Remedy: | 1 Checking the fuser motor The fuser motor operation is faulty. Execute U030 [Fuser] and check the fuser motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Fuser motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 4 Replacing the fuser motor The fuser motor is faulty. Replace the fuser motor. Detaching and reattaching the fuser drive unit 5 Replacing the fuser drive unit The fuser drive unit is faulty. Replace the fuser drive unit. Detaching and reattaching the fuser drive unit 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C2400 |
Description: | Eject motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s. |
Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective eject motor. Defective engine PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC25 on the engine PWB and the connector on the eject motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective eject motor. Run maintenance item U030 and check if the eject motor operates when YC25-A5 (remote signal) on the engine PWB goes low. If not, replace the eject motor. Defective engine PWB. Run maintenance item U030 and check if YC25-A5 (remote signal) on the engine PWB goes low. If not, replace the engine PWB. |
Error code: | C2500 |
Description: | Feed motor error |
Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
Error code: | C2600 |
Description: | PF feed motor error |
Causes: | The ready signal is not at the L level (stable rotation) after passing 1s since the PF feed motor drive started. |
Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected, or it is faulty. Execute U247 [2PF] or [LCF] > [Motor On] to check the paper feed operation. If the PF feed motor does not operate properly, reconnect the connector of the motor. Check if the PF feed roller and the drive gears rotate smoothly and have no excessive load, apply the grease (EM-50LP, Part no.: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF PWB • PF PWB - Engine PWB (Drawer connector between the paper feeder and the main unit) Service Manual - Section 8 `PWBs` 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF Drive Unit 4 Firmware upgrade The engine firmware or the PF firmware is faulty. Upgrade the engine firmware and the PF firmware to the latest version. Firmware Update 5 Replacing the PF PWB The PF PWB is faulty. Replace the PF PWB. Detaching and reattaching the PF PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
Error code: | C2810 |
Description: | Waste toner motor error |
Causes: | The steady-state speed error, FG pulse abnormal stop, or the abnormal motor drive is detected when reading the error signal from the motor at every 1s. |
Remedy: | 1 Checking the waste toner box The waste toner box is not properly installed. Reinstall the waste toner box. Detaching and reattaching the waste toner box 2 Checking the waste toner motor The waste toner motor does not operate properly. Check if the waste toner motor has no excessive load, and repair it. 3 Checking the drive gear The drive gear does not rotate properly. Check if the excessive load is not applied to the drive gears by rotating the gears, and clean the drive gears and the bushing, etc. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Waste toner motor - Front PWB?• Front PWB - Engine PWB Wiring diagram 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C3100 |
Description: | Carriage error |
Causes: | When turning the power on or finishing originals scan through the scanner, the alignment of the home position sensor (turning on / off the sensor) fails and the error is detected. Then, the error is detected twice continuously even the initial operation is executed. |
Remedy: | 1 Unlocking the scanner mirror frame The scanner mirror frame is not unlocked. Unlock the scanner mirror frame (lamp unit assy). Unlocking the scanner mirror frame 2 Checking the scanner movement A load is applied to the scanner movement. Check the operation of the lamp by U073 or manually moving it. If there is an excess load, check if there are any foreign objects on the optical wire or optical wire drum and clean it. After that, apply grease on the scanner rail. Detaching and reattaching the scanner wires 3 Checking the scanner wires The scanner wires are dirty or come off. Clean and reattach the scanner wires. Detaching and reattaching the scanner wires 4 Checking the scanner motor The scanner motor is faulty. Reattach the scanner motor and reconnect the connector. If not repaired, replace it. 5 Checking the belt tension of the scanner motor A load is applied to the scanner movement since the belt tension is improper. Adjust the scanner motor belt tension properly. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Scanner motor - Engine PWB Wiring diagram 7 Checking the home position sensor The home position sensor is not properly attached. Reattach the home position sensor. 8 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Home position sensor - Engine PWB Wiring diagram 9 Replacing the home position sensor The home position sensor is faulty. Replace the home position sensor. 10 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C3200 |
Description: | LED lamp startup error |
Causes: | The white reference data acquired by lighting the LED lamp at the initial operation does not reach the specified value. Or, the light amount detected by the CCD PWB is not enough. (2 or more LED lamps do not light. The light does not reach the CCD PWB due to condensation.) |
Remedy: | 1 Checking the LED lamp The LED lamp does not light. Execute U061 [CCD] and check if the LED lamp is lit. If not, replace the lamp unit. After that, execute U411 [Table(ChartA)]. Detaching and reattaching the lamp unit 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB • LED PWB - CCD PWB Wiring diagram 3 Checking the mirror The mirror or lens is frosted due to condensation. Clean the mirrors. If the condensation at the scanner section is resolved naturally by opening the document processor or the platen cover, turn the power switch off and on. 4 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C3300 |
Description: | CCD AGC error (For the internal count) |
Causes: | Brightness of the LED lamp is darker while one of the LED lamp does not turn on or brighter than expected when processing the AGC for the CCD lamp. |
Remedy: | 1 Checking the LED lamp The LED lamp is faulty. Check if the LED lamp lights by executing U061 [CCD]. If it does not light, replace the lamp unit and execute U411 [Table (ChartA) ]. Detaching and reattaching the lamp unit 2 Cleaning the backside of the contact glass The white reference sheet is dirty. Clean the white reference sheet at the backside of the contact glass. Detaching and reattaching the contact glass 3 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is peeled off, deformed or the FFC is broken, replace the FFC. • LED PWB - CCD PWB • CCD PWB - Engine PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 5 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C3500 |
Description: | Communication error between the scanner and the ASIC |
Causes: | The communication error is detected during the communication between the scanner ASIC and the scanner CPU. |
Remedy: | 1 Resetting the main power ASIC does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C3900 |
Description: | Scanner backup memory read / write error (Engine EEPOM) |
Causes: | The read-back value of the engine EEPROM differs. |
Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. Detaching and reattaching the EEPROM 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C3910 |
Description: | Backup memory read/write error (scanner PWB) • Data in the specified area of the backup memory does not match the specified values. |
Causes: | Problem with the backup memory data. Defective scanner PWB. |
Remedy: | Problem with the backup memory data. Run maintenance item U022 to initialize the backup memory data. Defective scanner PWB. If the C3910 is displayed after initializing the backup memory, replace the main PWB and check for correct operation. |
Error code: | C4000 |
Description: | Polygon motor synchronization problem • The revolution does not reach the stable speed within 20 s of the START signal. |
Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
Error code: | C4010 |
Description: | Polygon motor steady-state problem • The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized. |
Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
Error code: | C4100 |
Description: | Exposure lamp stays on |
Causes: | Defective laser scanner unit. Defective main PWB. Poor contact in connector terminals. |
Remedy: | Defective laser scanner unit. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. Poor contact in connector terminals. Check the connection of connector YC8 on the main PWB. Repair or replace if necessary. |
Error code: | C4200 |
Description: | BD steady-state problem • ASIC of the main PWB detects a BD error A for 4000 ms after the polygon motor rotation has been stabilized. |
Causes: | Defective laser diode. Defective polygon motor. Defective main PWB. Poor contact in connector terminals. |
Remedy: | Defective laser diode. Replace the laser scanner unit. Defective polygon motor. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. Poor contact in connector terminals. Check the connection of connector YC8 on the main PWB and the continuity across the connector terminals. Repair or replace if necessary. |
Error code: | C5101 |
Description: | Main high-voltage error |
Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
Remedy: | 1 Reinstalling the high-voltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Repair the main charger roller contact (wire spring) inside the high-voltage PWB so that it firmly contacts. Detaching and reattaching the high-voltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw does not properly rotate due to the excessive load. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Replacing the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity.• High-voltage PWB - Engine PWB Wiring diagram 7 Replacing the high-voltage PWB The high-voltage PWB is faulty. Replace the high-voltage PWB. Detaching and reattaching the high-voltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C5102 |
Description: | Main high-voltage error C |
Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C5103 |
Description: | Main high-voltage error M |
Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C5104 |
Description: | Main high-voltage error Y |
Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
Remedy: | 1 Reinstalling the main highvoltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Correct the main charger roller contact (wire spring) at the inner side of the main high-voltage PWB so that it is firmly grounded. Detaching and reattaching the main highvoltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw is not rotated properly due to the excessive load. Check if the drum or the drum screw is rotated manually, and replace the drum unit if not rotated. Detaching and reattaching the drum unit 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. Detaching and reattaching drum drive unit K and drum drive unit MCY 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • Main highvoltage PWB - Engine PWB Wiring diagram 7 Replacing the main highvoltage PWB The main high-voltage PWB is faulty. Replace the main high-voltage PWB. Detaching and reattaching the main highvoltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C5301 |
Description: | Cleaning lamp K error |
Causes: | Poor contact in the connector terminals. Defective cleaning lamp K. Defective PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the main front PWB and the connector of the drum unit K, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp K. Replace the drum unit K. Defective PWB. Replace the main front PWB or engine PWB and check for correct operation. |
Error code: | C5302 |
Description: | Cleaning lamp C error |
Causes: | Poor contact in the connector terminals. Defective cleaning lamp C. Defective PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC5 on the sub front PWB and the connector of the drum unit C, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp C. Replace the drum unit C. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
Error code: | C5303 |
Description: | Cleaning lamp M error |
Causes: | Poor contact in the connector terminals. Defective cleaning lamp M. Defective PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC7 on the sub front PWB and the connector of the drum unit M, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp M. Replace the drum unit M. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
Error code: | C5304 |
Description: | Cleaning lamp Y error |
Causes: | Poor contact in the connector terminals. Defective cleaning lamp Y. Defective PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the sub front PWB and the connector of the drum unit Y, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp Y. Replace the drum unit Y. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
Error code: | C6000 |
Description: | IH heating error 1 |
Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
Error code: | C6010 |
Description: | Abnormally high fuser thermistor temperature The fuser Abnormally high signal is detected for 60 s or more. |
Causes: | Defective PWB. |
Remedy: | Replace the power source PWB or engine PWB and check for correct operation. |
Error code: | C6020 |
Description: | Fuser center thermistor high temperature error |
Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
Error code: | C6030 |
Description: | Fuser center thermistor broken |
Causes: | The output from the fuser center thermistor is under 20°C / 68°F level during warm-up. Or, the temperature detected at the fuser center thermistor does not change for 10s after turning the fuser heater on. |
Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
Error code: | C6050 |
Description: | Fuser center thermistor low temperature error |
Causes: | The fuser center thermistor detects less than 100°C / 212°F for 1s after warm-up, or during print or standby. |
Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 11 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit |
Error code: | C6100 |
Description: | Fuser heater broken (For the internal count) |
Causes: | The fuser press thermistor temperature detected does not reach the control temperature within 480s after shifting to the low power mode. |
Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
Error code: | C6120 |
Description: | Fuser press thermistor high temperature error |
Causes: | The fuser press thermistor detects 210°C / 410°F or more for 1s. |
Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
Error code: | C6130 |
Description: | Fuser press thermistor broken |
Causes: | The detection temperature of the fuser press thermistor does not reach 30°C / 86°F within 60s since warm-up starts. |
Remedy: | 1 Removing foreign material There are foreign objects between the fuser press thermistor and the press roller. Or, the foreign objects are adhered on the press roller. Remove foreign objects if any on the press roller. Then, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
Error code: | C6400 |
Description: | Zero-cross signal error • The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s. |
Causes: | Poor contact in the connector terminals. Defective DC power source PWB. Defective engine PWB |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and YC6 on the DC power source PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective DC power source PWB. Check if the zero-crossing signal is output from YC6-3 on the DC power source PWB. If not, replace the DC power source PCB. Defective engine PWB. Replace the engine PWB if C6400 is detected while YC6-3 on the DC power source PWB outputs the zero-crossing signal. |
Error code: | C7000 |
Description: | Toner motor problem After driving of the toner motor starts, the error signal is not at the H level for 500 ms continuously. |
Causes: | Poor contact in the connector terminals. Broken the gear Defective toner motor M/C/Y/K. Defective engine PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC26 on the engine PWB and the connector of the toner motor, and the continuity across the connector terminals. Repair or replace if necessary. Broken the gear. Check visually and replace the gear if necessary. Defective toner motor M/C/Y/K. Run maintenance item U135 and check if the toner motor operates. If not, replace the toner motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
Error code: | C7101 |
Description: | Toner sensor error |
Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The drive gears for the developer unit are damaged. (The spiral cannot rotate.) Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7102 |
Description: | Toner sensor C error |
Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
Error code: | C7103 |
Description: | Toner sensor M error |
Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7104 |
Description: | Toner sensor Y error |
Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7200 |
Description: | Internal thermistor broken (For the internal count) |
Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) exceeds the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7210 |
Description: | Internal thermistor short-circuited (For the internal count) |
Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) is less than the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7220 |
Description: | Broken internal thermistor 2 wire An abnormal value is detected in the input data to inner temperature sensor 2. |
Causes: | Poor contact in the connector terminals. Defective engine PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC28 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB and check for correct operation. |
Error code: | C7230 |
Description: | Short-circuited internal thermistor 2 An abnormal value is detected in the input data to inner temperature sensor 2. |
Causes: | Poor contact in the connector terminals. Defective engine PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC28 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB and check for correct operation. |
Error code: | C7240 |
Description: | Broken internal thermistor 2 wire An abnormal value is detected in the input data to inner temperature sensor 2. |
Causes: | Poor contact in the connector terminals. Defective engine PWB |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC8 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB and check for correct operation. |
Error code: | C7250 |
Description: | Short-circuited internal thermistor 2 An abnormal value is detected in the input data to inner temperature sensor 2. |
Causes: | Poor contact in the connector terminals. Defective engine PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC8 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB and check for correct operation. |
Error code: | C7401 |
Description: | Developer unit type mismatch error |
Causes: | "Unit Identification" of the EEPROM in the developer unit does not match the main unit. |
Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB• Front PWB - Engine PWB Wiring diagram 2 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7402 |
Description: | Developer unit C type mismatch error |
Causes: | "Unit Identification" of the EEPROM in the developer unit C does not match the main unit. |
Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB?• Front PWB - Engine PWB Wiring diagram 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7403 |
Description: | Developer unit M type mismatch error |
Causes: | "Unit Identification" of the EEPROM in the developer unit M does not match the main unit. |
Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB • Front PWB - Engine PWB Wiring diagram 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7404 |
Description: | Developer unit Y type mismatch error |
Causes: | "Unit Identification" of the EEPROM in the developer unit Y does not match the main unit. |
Remedy: | 1 Checking the developer unit The developer unit of the different type is installed. Install the proper developer unit. Detaching and reattaching the developer unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB• Front PWB - Engine PWB 3 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7411 |
Description: | Drum unit type mismatch error |
Causes: | "Unit Identification" of the EEPROM in drum unit does not match the main unit. |
Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 2 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. Detaching and reattaching the drum unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7412 |
Description: | Drum unit C type mismatch error |
Causes: | "Unit Identification" of the EEPROM in drum unit C does not match the main unit. |
Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. Detaching and reattaching the drum unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7413 |
Description: | Drum unit M type mismatch error |
Causes: | "Unit Identification" of the EEPROM in drum unit M does not match the main unit. |
Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7414 |
Description: | Drum unit Y type mismatch error |
Causes: | "Unit Identification" of the EEPROM in drum unit Y does not match the main unit. |
Remedy: | 1 Checking the drum unit and the developer unit The drum unit of the different type is installed. Install the proper drum unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB• Front PWB - Engine PWB Wiring diagram 3 Replacing the dum unit The drum unit (EEPROM) is faulty. Replace the drum unit. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. Detaching and reattaching the front PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7420 |
Description: | Uninstalled primary transfer unit |
Causes: | 1. Unit identification code does not match. 2. Unit for the other model is installed. |
Remedy: | 1 Replacing the primary transfer unit The primary transfer unit for other models is installed. Install the primary transfer unit for the applicable models. Detaching and reattaching the Primary Transfer Unit 2 Reinstalling the primary transfer unit The connector of the primary transfer unit is not firmly connected. Reinstall the primary transfer unit so that the connector firmly connects. Detaching and reattaching the Primary Transfer Unit 3 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Transfer connect PWB - Feed image PWB Service Manual - Section 8 `PWBs` 4 Firmware upgrade The firmware is faulty. Reinstall the engine firmware. Firmware Update 5 Replacing the transfer connection PWB The transfer connection PWB is faulty. Replace the transfer connection PWB. 6 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. |
Error code: | C7800 |
Description: | Outer thermistor broken (For the internal count) |
Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7810 |
Description: | Short-circuited external thermistor • The thermistor input value is 0.5 V or less. |
Causes: | Poor contact in the connector terminals. Defective humidity sensor. Defective engine PWB |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC13 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective humidity sensor. Replace the humidity sensor. Defective engine PWB. Replace the engine PWB. |
Error code: | C7901 |
Description: | Drum unit EEPROM error |
Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB • Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7902 |
Description: | Drum unit C EEPROM error |
Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB • Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7903 |
Description: | Drum unit M EEPROM error |
Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7904 |
Description: | Drum unit Y EEPROM error |
Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB?• Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7911 |
Description: | Developer unit EEPROM error |
Causes: | The toner sensor (EEPROM) in the developing unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit - Front PWB • Front PWB - Engine PWB Wiring diagram 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7912 |
Description: | Developer unit C EEPROM error |
Causes: | The toner sensor (EEPROM) in the developing unit C cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit C - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7913 |
Description: | Developer unit M EEPROM error |
Causes: | The toner sensor (EEPROM) in the developing unit M cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit M - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C7914 |
Description: | Developer unit Y EEPROM error |
Causes: | The toner sensor (EEPROM) in the developing unit Y cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit M - Front PWB • Front PWB - Engine PWB 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
Error code: | C8020 |
Description: | Punch motor error 2 Object: 4000-sheet finisher + Punch unit |
Causes: | The home position is not aligned within 3s when initializing the home position or standby. |
Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
Error code: | C8030 |
Description: | Punch motor error 3 Object: 4000-sheet finisher + Punch unit |
Causes: | The home position detection does not turn off within 50ms when initializing the home position. |
Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
Error code: | C8050 |
Description: | Punch shift motor error 2 Object: 100-sheet staple finisher |
Causes: | The paper edge cannot be detected if driving the motor by the specified distance (30mm) when detecting the paper edge. |
Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit does not move manually, repair the position where restricts the operation. 2 Checking the PH cam drive parts The PH cam drive parts are not attached properly or faulty. Reattach the punch cam drive components. Replace it if not repaired 3 Checking the connection The connector is not properly connected. Or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EPunch shift motor - PH PWB EPaper edge sensor 1,2 - PH PWB EPH PWB- DF PWB 4 Replacing the punch shift motor The punch shift motor is faulty. Execute U240 mMotorn > mPunch Moven Replace the punch shift motor if it does not operate properly. 5 Checking the paper edge sensors 1, 2 Paper edge sensors 1, 2 are not properly attached or faulty. Execute U241 mPunchn > mEdge Face1/2n Reattach the paper edge sensors 1, 2 if they do not operate properly. Replace the paper edge sensors 1, 2 if not repaired. 6 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. 7 Replacing PH PWB PH PWB is faulty. Replace PH PWB. 8 Replacing DF PWB DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. |
Error code: | C8060 |
Description: | Paper conveying belt motor 2 problem (optional 3000-sheet document finisher) Paper conveying belt home position sensor 2 does not turn off within 1.5 s. Paper conveying belt home position sensor 2 does not turn on within 1.5 s. |
Causes: | Poor contact in the connector terminals. Defective paper conveying belt home position sensor 2. Defective paper conveying belt motor 2. Defective PWB |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 on the inner tray PWB and the connector on paper conveying belt motor 2, and the continuity across the connector terminals. Repair or replace if necessary. Defective paper conveying belt home position sensor 2. Replace paper conveying belt home position sensor 2. Defective paper conveying belt motor 2. Replace paper conveying belt motor 2. Defective PWB. Replace the inner tray PWB or finisher main PWB and check for correct operation. |
Error code: | C8070 |
Description: | Inner tray communication error (optional 3000-sheet document finisher) Communication with the inner tray is not possible although the connection is detected. |
Causes: | Poor contact in the connector terminals. Defective PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector YC6 and YC24 on the finisher main PWB and the connector YC1 and YC4 on the inner tray PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the inner tray PWB or finisher main PWB and check for correct operation. |
Error code: | C8140 |
Description: | Main tray error 1 Object: 4000-sheet finisher |
Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
Error code: | C8170 |
Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
Error code: | C8180 |
Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
Error code: | C8210 |
Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
Error code: | C8220 |
Description: | Document finisher* front clincher problem • During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position. JAM90 is indicated the first time this problem occurs. If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher. • When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms. |
Causes: | Loose connection of the front clincher motor connector. Malfunction of the front clincher motor. Malfunction of the front clincher home position sensor. Loose connection of the front clincher home position sensor connector. Defective finisher main PWB. |
Remedy: | Loose connection of the front clincher motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Malfunction of the front clincher motor. Replace the front clincher motor and check for correct operation. Malfunction of the front clincher home position sensor. Replace the front clincher home position sensor and check for correct operation. Loose connection of the front clincher home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
Error code: | C8230 |
Description: | DF staple motor error Object: 4000-sheet finisher |
Causes: | J7000 (DF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple cannot operate manually without paper jam, repair the part that restricts the DF staple. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple unit - DF main PWB Wiring diagram 3 Replacing the DF staple unit The DF staple unit is faulty. Replace the DF staple unit. Detaching and reattaching the DF staple unit 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
Error code: | C8300 |
Description: | Main program error / Folding unit communication error Object: 4000-sheet finisher + Folding unit |
Causes: | The main program of the folding unit is faulty when turning the power on. The communication error appears 10 times continuously after finishing the folding unit firmware version reading. |
Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the BF firmware and the DF firmware to the latest version. Firmware Update 3 Checking the BF set switch The BF set switch is not properly attached. Reattach the BF set switch. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 5 Replacing the BF set switch The BF set switch is faulty. Execute U241 [Booklet] > [Set]. If the BF set switch does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
Error code: | C8310 |
Description: | BF side registration motor 2 error Object: 4000-sheet finisher + Folding unit |
Causes: | BF side registration sensor 2 does not turn on after passing 1s during the initial operation. |
Remedy: | 1 Checking the upper BF side registration guide The upper BF side registration guide is not assembled properly. If the upper BF side registration guide is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the upper BF side registration guide drive components The upper BF side registration guide drive parts are not properly attached or faulty. Reattach the upper BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 2 - BF main PWB • BF side registration sensor 2 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 2 BF side registration motor 2 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 2 BF side registration sensor 2 is not properly attached or faulty. Reattach BF side registration sensor 2 and execute U241 [Booklet] > [Width Down HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
Error code: | C8320 |
Description: | BF adjustment motor error Object: 4000-sheet finisher + Folding unit |
Causes: | At the initialization, turning on of the BF adjustment sensor is not detected after 2.5s passes. |
Remedy: | 1 Checking the BF shift belt The BF shift belt is not assembled properly. If the BF shift belt is not operated manually, repair the part that restricts the operation. 2 Checking the BF shift belt drive components The BF shift belt drive parts are not properly attached or faulty. Reattach the BF shift belt drive parts. Reattach it if the belt comes off. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF adjustment motor 1, 2 - BF main PWB • BF adjustment sensor 1, 2 - BF main PWB Wiring diagram 4 Replacing BF adjustment motor 1, 2 BF adjustment motor 1 or 2 is faulty. Execute U240 [Booklet] > [Bundle Down] or [Bundle Up]. If BF adjustment motor 1 or 2 does not properly operate, replace them. Executing U240 5 Checking BF adjustment sensor 1, 2 BF adjustment sensor 1 or 2 is not properly attached or faulty. Reattach BF adjustment sensor 1 or 2 and execute U241 [Booklet] > [Width Down HP] or [Bundle Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
Error code: | C8330 |
Description: | BF blade motor error Object: 4000-sheet finisher + Folding unit |
Causes: | The BF blade sensor does not turn on after passing 3s during the initial operation. |
Remedy: | 1 Checking the BF blade The BF blade is not assembled properly. If the BF blade is not operated manually, repair the part that restricts the operation. 2 Checking the BF blade drive components The BF blade drive parts are not properly attached or faulty. Reattach the BF blade drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF blade motor - BF main PWB • BF blade sensor - BF main PWB Wiring diagram 4 Replacing the BF blade motor The BF blade motor is faulty. Execute U240 [Booklet] > [Blade]. If the BF blade motor does not properly operate, replace it. Executing U240 5 Checking the BF blade sensor The BF blade sensor is faulty. Reattach the BF blade sensor and reinsert the connector. Next, execute U241 [Booklet] > [Blade HP]. If it does not properly operate, replace the sensor. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
Error code: | C8340 |
Description: | BF staple motor error 1 Object: 4000-sheet finisher + Folding unit |
Causes: | J7600 (BF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
Remedy: | 1 Checking the BF staple unit The BF staple unit is not assembled properly. If the BF staple unit is not operated manually, repair the part that restricts the operation. 2 Checking the BF staple unit drive components The BF staple unit drive parts are not properly attached or faulty. Reattach the BF staple unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF staple unit - BF main PWB Wiring diagram 4 Replacing the BF staple motor The BF staple motor is faulty. Execute U240 [Booklet] > [Staple]. If the BF staple motor does not properly operate, replace it. Executing U240 5 Replacing the BF staple unit The BF staple unit is faulty. Replace the BF staple unit. 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
Error code: | C8350 |
Description: | BF side registration motor 1 error Object: 4000-sheet finisher + Folding unit |
Causes: | BF side registration sensor 1 does not turn on after passing 1s during the initial operation. |
Remedy: | 1 Checking the lower BF side registration guide The lower BF side registration guide is not assembled properly. If the lower BF side registration guide is not operated manually, repair the part that restricts the operation. 2 Checking the lower BF side registration guide drive components The lower BF side registration guide drive parts are not properly attached or faulty. Reattach the lower BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 1 - BF main PWB • BF side registration sensor 1 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 1 BF side registration motor 1 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 1 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 1 BF side registration sensor 1 is not properly attached or faulty. Reattach BF side registration sensor 1 and execute U241 [Booklet] > [Width Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
Error code: | C8360 |
Description: | BF main motor error Object: 4000-sheet finisher + Folding unit |
Causes: | The lock-up signal was detected for 1s continuously during the motor operation. |
Remedy: | 1 Checking the BF conveying roller The BF conveying roller is not assembled properly. If the BF conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the BF conveying roller drive parts The BF conveying roller drive parts are not properly attached or faulty. Reattach the BF conveying roller drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main motor - BF main PWB Wiring diagram 4 Replacing the BF main motor The BF main motor is faulty. Execute U240 [Booklet] > [Folding]. If the BF main motor does not properly operate, replace it. Executing U240 5 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
Error code: | C8440 |
Description: | Sensor adjusting problem (optional document finisher) The sensor cannot be adjusted within the specified range. |
Causes: | The paper entry sensor connector makes poor contact. Defective paper entry sensor. The optical path of the paper entry sensor is blocked by foreign matter. Defective finisher main PWB. |
Remedy: | The paper entry sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective paper entry sensor. Replace the paper entry sensor and check for correct operation. The optical path of the paper entry sensor is blocked by foreign matter. Remove the foreign matter. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
Error code: | C8460 |
Description: | EEPROM problem (optional document finisher) Reading from or writing to EEPROM cannot be performed. |
Causes: | Defective EEPROM or finisher main PWB. |
Remedy: | Replace the finisher main PWB and check for correct operation. |
Error code: | C8500 |
Description: | Main program error (Mail Box) / Mail Box communication error Object: 4000-sheet finisher + Mail box |
Causes: | The main program of the mail box is faulty when turning the power on. The communication error appears 10 times continuously after finishing the mail box firmware version reading. |
Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the MB firmware and the DF firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB main PWB - DF main PWB 4 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
Error code: | C8510 |
Description: | MB conveying motor error 1 Object: 4000-sheet finisher + Mail box |
Causes: | The MB home position sensor does not turn on after passing 5s during the initial operation. |
Remedy: | 1 Checking the MB conveying roller The MB conveying roller is not assembled properly. If the MB conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB conveying motor - MB main PWB • MB home position sensor - MB main PWBPWB Wiring diagram 3 Replacing the MB conveying motor The MB conveying motor is faulty. Execute U240 [Mail Box] > [Conv]. If the MB conveying motor does not properly operate, replace it. 4 Checking the MB home position sensor The MB home position sensor is not properly attached or faulty. Reattach the MB home position sensor and execute U241 [Mail Box] > [Motor HP]. If the sensor does not properly operate, replace it. Executing U241 5 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. |
Error code: | C8900 |
Description: | DF backup error Object: 4000-sheet finisher (For the internal count) |
Causes: | The writing data and the reading data mismatch 3 times continuously. |
Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 2 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
Error code: | C8910 |
Description: | Backup memory data problem (optional of 3000-sheet document finisher) Read and write data does not match 3 times in succession. |
Causes: | Poor contact in the connector terminals Defective punch PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector on the punch PWB and the connector YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective punch PWB. Replace the punch PWB and check for correct operation. |
Error code: | C8920 |
Description: | Mailbox backup problem (optional mailbox of 3000-sheet document finisher) Read and write data does not match. |
Causes: | Poor contact in the connector terminals. Defective mailbox main PWB. |
Remedy: | Poor contact in the connector terminals. Check the connection of connector on the mailbox main PWB and the connector YC7 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective mailbox main PWB. Replace the mailbox main PWB and check for correct operation. |
Error code: | C8930 |
Description: | BF unit backup error Object: 4000-sheet finisher + Folding unit (For the internal count) |
Causes: | The writing data and the reading data mismatch 3 times continuously. |
Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 2 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
Error code: | C9060 |
Description: | DP EEPROM error |
Causes: | Read data and write data to the EEPROM do not match 3 times continuously. |
Remedy: | 1 Checking the EEPROM The EEPROM is not properly installed. Reattach the EEPROM on the DP main PWB. 2 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the DP main PWB and execute U411. |
Error code: | C9500 ... C9550 |
Description: | Contact the Service Administrative Division. |
Remedy: | Contact the Service Administrative Division. |
Название
Kyocera Блок фотобарабана
Kyocera Узел термозакрепления
Kyocera Сервисный комплект
Kyocera Сервисный комплект
Kyocera Тонер-картридж голубой
Kyocera Тонер-картридж черный
Kyocera Тонер-картридж пурпурный
Kyocera Тонер-картридж желтый