Kyocera KM-C2630
Рейтинг
Модули
ACCESSORIES & OPTION I
FRAME SECTION I
Electrical Components I
DUPLEX UNIT III (KM-C2630D)
SCANNER UNIT
ACCESSORIES & OPTION II
CONVEYANCE UNIT (KM-C2630D)
EXIT SECTION II
DRIVING SECTION I
CASSETTE (KM-C2630)
FRAME SECTION II
PRIMARY PAPER FEED SECTION (KM-C2630)
FUSER UNIT
FEED SECTION I
OPTION III (AK-640A)
TRANSFER UNIT
DUPLEX UNIT II (KM-C2630D)
EXIT SECTION I
Electrical Components II
OPERATION UNIT
Process Unit
Scanner covers
DUPLEX UNIT I (KM-C2630D)
Exterior Covers
DRIVING SECTION II
ELECTRICAL COMPONENTS III
FEED SECTION II
Детали EXIT SECTION I
| Деталь: | TRAY OP |
| Парткод: | 2BG60010 |
| Деталь: | BKT OP TRAY F |
| Парткод: | 2BG60020 |
| Деталь: | BKT OP TRAY R |
| Парткод: | 2BG60100 |
| Деталь: | Controller assy |
| Парткод: | 3H001013 |
| Деталь: | RAIL OPTION A |
| Парткод: | 2BL26210 |
| Деталь: | GUIDE CF CARD |
| Парткод: | 2BM26020 |
| Деталь: | RAIL OPTION B |
| Парткод: | 2BL26220 |
| Деталь: | DIMM ASSY |
| Парткод: | 3H001030 |
| Деталь: | FAN 80X15-60 |
| Парткод: | 2BF27020 |
| Деталь: | IC DIMM-128M |
| Парткод: | 2BF27050 |
| Деталь: | GASKET SHIELD PRN |
| Парткод: | 3H027010 |
| Деталь: | PLATE,OPTION |
| Парткод: | 3BH26020 |
| Деталь: | PIN,OPTION |
| Парткод: | 3BH26030 |
| Деталь: | PLATE MAIN |
| Парткод: | 2BG26031 |
| Деталь: | PAD,LIFT |
| Парткод: | 3C007060 |
| Деталь: | WIRE,HDD POWER SOURCE(KM-C2630) |
| Парткод: | 2A660240 |
| Деталь: | WIRE,HDD(KM-C2630) |
| Парткод: | 2A660230 |
| Деталь: | PARTS,UNIT HDD(S P)(KM-C2630) |
| Парткод: | 2FA93130 |
| Деталь: | CORE ESD-FPD-40(KM-C2630) |
| Парткод: | 3CV27040 |
| Деталь: | MOUNT MCS PCB(KM-C2630) |
| Парткод: | 2A660210 |
| Деталь: | MCS PCB ASSY(KM-C2630) |
| Парткод: | 3CV01010 |
| Деталь: | IC,DIMM MEMORY1(KM-C2630) |
| Парткод: | 2A727740 |
| Деталь: | HEATER,DEHUMIDIFIER(120) |
| Парткод: | 2BG28740 |
| Деталь: | HEATER,DEHUMIDIFIER(230) |
| Парткод: | 2BG28750 |
| Деталь: | CORE SFT-72SNB-026K |
| Парткод: | 2C927230 |
| Деталь: | CLAMP,EMT-6N(TAKEUCHI) |
| Парткод: | M7005020 |
| Деталь: | WIRE,FGM-150-M4 |
| Парткод: | 2BG28940 |
| Деталь: | WIRE,TONER EMPTY SWITCH |
| Парткод: | 2BG27830 |
| Деталь: | FOOT |
| Парткод: | 2BG02390 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | 49513902 |
| Деталь: | HANDLE |
| Парткод: | 2BG02180 |
| Деталь: | CAP HANDLE |
| Парткод: | 2BG02470 |
| Деталь: | CAP HANDLER |
| Парткод: | 2BG02480 |
| Деталь: | GUIDE CONTAINER Y |
| Парткод: | 2BF15030 |
| Деталь: | GUIDE CONTAINER K |
| Парткод: | 2BG15170 |
| Деталь: | SPRING CONTAINER EJECT |
| Парткод: | 2BG15180 |
| Деталь: | WIRE,DUPLEX JUNCTION |
| Парткод: | 2BG27680 |
| Деталь: | SCREW A |
| Парткод: | 2BG02410 |
| Деталь: | HOLDER IMAGE R |
| Парткод: | 2BG09040 |
| Деталь: | GROUND DRAWER |
| Парткод: | 2BG02430 |
| Деталь: | PLATE CONTACT WIRE |
| Парткод: | 2BG10111 |
| Деталь: | PLATE SPRING GRID |
| Парткод: | 2BG10121 |
| Деталь: | MOUNT PAPER SIZE |
| Парткод: | 2BG06890 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | WIRE,CASSETTE LENGTH SW |
| Парткод: | 2BG27230 |
| Деталь: | RECEPTACLE,QR/P15-8S-C(02)(HIROSE) |
| Парткод: | J0464080 |
| Деталь: | WIRE,CASSETTE SIZE |
| Парткод: | 2BG27240 |
| Деталь: | SCREW B |
| Парткод: | 2BG02420 |
| Деталь: | GUIDE TC R |
| Парткод: | 2BG02610 |
| Деталь: | PULLEY RAIL B |
| Парткод: | 2BG02770 |
| Деталь: | LEVER LOCK TC R |
| Парткод: | 2BG02630 |
| Деталь: | PIN LOCK TC |
| Парткод: | 2BG02650 |
| Деталь: | SPRING COVER R |
| Парткод: | 3B706550 |
| Деталь: | LOCK COVER R |
| Парткод: | 2BL06490 |
| Деталь: | SPRING LOCK TC |
| Парткод: | 2BG02640 |
| Деталь: | SPRING EARTH RAIL |
| Парткод: | 2BG06710 |
| Деталь: | HOLDER DU DRIVE |
| Парткод: | 2BG22850 |
| Деталь: | SHEET HARNESS R |
| Парткод: | 2BG02740 |
| Деталь: | WIRE,IU JUNCTION M |
| Парткод: | 2BF27110 |
| Деталь: | WIRE,IU JUNCTION M |
| Парткод: | 2BG27640 |
| Деталь: | WIRE,IU JUNCTION C |
| Парткод: | 2BF27120 |
| Деталь: | WIRE,IU JUNCTION C |
| Парткод: | 2BG27650 |
| Деталь: | WIRE,IU JUNCTION Y |
| Парткод: | 2BF27130 |
| Деталь: | WIRE,IU JUNCTION Y |
| Парткод: | 2BG27660 |
| Деталь: | WIRE,IU JUNCTION K |
| Парткод: | 2BF27100 |
| Деталь: | WIRE,IU JUNCTION K |
| Парткод: | 2BG27630 |
| Деталь: | SPONGE HOLDER IMAGE |
| Парткод: | 2BG09280 |
| Деталь: | SENSOR,TONER EMPTY B |
| Парткод: | 2BG27020 |
| Деталь: | RAIL FUSER R |
| Парткод: | 2BG02230 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BG02240 |
| Деталь: | PIN HOOK |
| Парткод: | 2BG02400 |
| Деталь: | PIN PULLEY |
| Парткод: | 2BG20350 |
| Деталь: | SHEET RM |
| Парткод: | 2BG02780 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE,BYPASS JUNCTION |
| Парткод: | 2BG27611 |
| Деталь: | SWITCH,INTERLOCK |
| Парткод: | 2AV27370 |
| Деталь: | SENSOR 12,SEPARATION |
| Парткод: | 3B827040 |
| Деталь: | COVER SCREW |
| Парткод: | 2BG04560 |
| Деталь: | SEAL PLATE LPH A |
| Парткод: | 2BG02810 |
| Деталь: | SEAL PLATE LPH B |
| Парткод: | 2BG02820 |
| Деталь: | FRONT PCB JUNCTION ASSY |
| Парткод: | 2BG01130 |
| Деталь: | COVER DESK DRAWER |
| Парткод: | 2BG02490 |
| Деталь: | SWITCH,MAIN |
| Парткод: | 2BG27060 |
| Деталь: | WIRE,MSW A |
| Парткод: | 2BG28900 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | LOCKING WIRE SADDLE,LWS-2NS |
| Парткод: | 49427223 |
| Деталь: | WIRE,DESK |
| Парткод: | 2BG27220 |
| Деталь: | WIRE,OPTION JUNCTION |
| Парткод: | 2BG27800 |
| Деталь: | WIRE,LIFT MOTOR |
| Парткод: | 2BG27330 |
| Деталь: | WIRE,COLOR DEVE MOTOR |
| Парткод: | 2BG27250 |
| Деталь: | WIRE,CLUTCH PCB |
| Парткод: | 2BG27430 |
| Деталь: | FERRITE CORE,SFT-72SN(TAKEUCHI) |
| Парткод: | M70CA010 |
| Деталь: | FERRITE CORE,SFT-59SN(TAKEUCHI) |
| Парткод: | M70C0010 |
| Деталь: | PCB ENGINE ASSY SP |
| Парткод: | 2BG68130 |
| Деталь: | LPH DRIVE ASSY |
| Парткод: | 2BG01035 |
| Деталь: | LPH ASSY(M)(C)(Y) |
| Парткод: | 2BG00231 |
| Деталь: | LPH BK ASSY(K) |
| Парткод: | 2BG00241 |
| Деталь: | HOLDER LPH F |
| Парткод: | 2BG13020 |
| Деталь: | LABEL CAUTION LPH |
| Парткод: | 2BG05030 |
| Деталь: | PLATE EARTH LPH |
| Парткод: | 2BG13070 |
| Деталь: | DUCT MCH GUIDE |
| Парткод: | 2BG13051 |
| Деталь: | HOLDER LPH R |
| Парткод: | 2BG13030 |
| Деталь: | STAY LPH |
| Парткод: | 2BG13060 |
| Деталь: | SENSOR 12,SEPARATION(M)(C)(Y) |
| Парткод: | 3B827040 |
| Деталь: | WIRE,T EMP SW JUNCTION(M)(C)(Y) |
| Парткод: | 2BG28600 |
| Деталь: | SEAL DUCT UP |
| Парткод: | 2BG13120 |
| Деталь: | WIRE,LPH(M) |
| Парткод: | 2BG27752 |
| Деталь: | WIRE,LPH(K) |
| Парткод: | 2BG28512 |
| Деталь: | WIRE,LPH(C) |
| Парткод: | 2BG28772 |
| Деталь: | WIRE,LPH(Y) |
| Парткод: | 2BG28782 |
| Деталь: | SPRING LPH A |
| Парткод: | 2BG13130 |
| Деталь: | CORE 8-16X10 |
| Парткод: | 3HK27050 |
| Деталь: | COVER DUCT MCH F |
| Парткод: | 2BG13081 |
| Деталь: | COVER DUCT MCH R |
| Парткод: | 2BG13091 |
| Деталь: | SEAL STAY LPH |
| Парткод: | 2BG13100 |
| Деталь: | STOPPER CONTAINER H |
| Парткод: | 2BF02530 |
| Деталь: | STOPPER CONTAINER B |
| Парткод: | 2BG02520 |
| Деталь: | CLAMP,EMT-4N(TAKEUCHI) |
| Парткод: | M70A5010 |
| Деталь: | SPONGE HARNESS F |
| Парткод: | 2BG02730 |
| Деталь: | WIRE,FRONT COVER SWITCH |
| Парткод: | 2BG27980 |
| Деталь: | DUCT FAN 40 |
| Парткод: | 2BG23050 |
| Деталь: | FAN 40 |
| Парткод: | 2BG23060 |
| Деталь: | WIRE,HUMIDITY SENSOR |
| Парткод: | 2BG27840 |
| Деталь: | WIRE,POWER SOURCE B |
| Парткод: | 2BG28560 |
| Деталь: | WIRE,DRUM MOTOR |
| Парткод: | 2BG27710 |
| Деталь: | DRUM DRIVE ASSY |
| Парткод: | 2BG00560 |
| Деталь: | MOTOR,DRUM |
| Парткод: | 2BG27120 |
| Деталь: | BEARING,608ZZ |
| Парткод: | 45506083 |
| Деталь: | SPRING JOINT D |
| Парткод: | 2BG22020 |
| Деталь: | JOINT DRUM |
| Парткод: | 2BG22010 |
| Деталь: | WIRE,POWER SOURCE A |
| Парткод: | 2BG27360 |
| Деталь: | WIRE,POWER SOURCE SIGNAL |
| Парткод: | 2BG27370 |
| Деталь: | WIRE,PRINTER SIGNAL |
| Парткод: | 2BG27420 |
| Деталь: | LABEL RED(M) |
| Парткод: | 2BG68160 |
| Деталь: | LABEL BLUE(C) |
| Парткод: | 2BG68170 |
| Деталь: | LABEL YELLOW(Y) |
| Парткод: | 2BG68180 |
| Деталь: | LABEL BLACK(K) |
| Парткод: | 2BG68190 |
| Деталь: | LPH |
| Парткод: | 2BG13010 |
| Деталь: | CORE 11-25X14 |
| Парткод: | 2A627930 |
| Деталь: | EEPROM,24LC256-I/P |
| Парткод: | NCQ05070 |
| Деталь: | WIRE,LPH PCB |
| Парткод: | 2BG27730 |
| Деталь: | CORE 8-18X13 |
| Парткод: | 2AV27430 |
| Деталь: | CORE 15-26X13 |
| Парткод: | 2AV27440 |
| Деталь: | CORE SFT-72SNB-026K |
| Парткод: | 2C927230 |
| Деталь: | WIRE,SCANNER DATA |
| Парткод: | 2BG27080 |
| Деталь: | WIRE,SCANNER POWER SOURCE |
| Парткод: | 2BG27090 |
| Деталь: | BINDING BAND,P-108 |
| Парткод: | 49821101 |
| Деталь: | SHIELD GASKET C |
| Парткод: | 2BG28970 |
| Деталь: | SHIELD GASKET D |
| Парткод: | 2BG28980 |
| Деталь: | SHIELD GASKET E |
| Парткод: | 2BG28990 |
| Деталь: | BINDING BAND,KB-100-1 |
| Парткод: | 49826601 |
| Деталь: | WIRE,LPH(M) R |
| Парткод: | 2BG28821 |
| Деталь: | WIRE,LPH(K) R |
| Парткод: | 2BG28831 |
| Деталь: | WIRE,LPH(C) R |
| Парткод: | 2BG28841 |
| Деталь: | WIRE,LPH(Y) R |
| Парткод: | 2BG28851 |
| Деталь: | WIRE,MAIN SWITCH SIGNAL |
| Парткод: | 2BG27260 |
| Деталь: | WIRE,UPPER EJECT SWITCH |
| Парткод: | 2BG27960 |
| Деталь: | M4 12 CRFREE ST |
| Парткод: | 2BG02860 |
| Деталь: | WASHER M4 10 CRFREE |
| Парткод: | 2BG02870 |
| Деталь: | Shield cover |
| Парткод: | 2BG28930 |
| Деталь: | SHEET LPH HARNESS |
| Парткод: | 2BG13110 |
| Деталь: | DUPLEX UNIT |
| Парткод: | 2BG68153 |
| Деталь: | PLATE DU TAP SOL |
| Парткод: | 2BG21400 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | LEVER,TRAILING EDGE TAPPING |
| Парткод: | 68721500 |
| Деталь: | SOLENOID DU TAPPING |
| Парткод: | 2BG07380 |
| Деталь: | SPRING.CLEANING UNIT LEVER |
| Парткод: | 48527321 |
| Деталь: | EDGING, EDS-0607U(KITAGAWA) |
| Парткод: | M2104260 |
| Деталь: | BELT DU CONVEY |
| Парткод: | 2BG21310 |
| Деталь: | BINDING BAND SG-130 |
| Парткод: | 49827700 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | SHAFT DU LEADING |
| Парткод: | 2BG21370 |
| Деталь: | TIMING PULLEY 27,LOOP |
| Парткод: | 73210350 |
| Деталь: | PLATE DU LEADING |
| Парткод: | 2BG21890 |
| Деталь: | BELT,LEADING EDGE |
| Парткод: | 62207180 |
| Деталь: | PULLEY 22,LEADING REGISTRATION |
| Парткод: | 2AC07400 |
| Деталь: | PULLEY,LEADING REGISTRATION |
| Парткод: | 68721420 |
| Деталь: | WEIGHT,LEADING FEED PULLEY |
| Парткод: | 33906180 |
| Деталь: | GEAR Z22S |
| Парткод: | 2BG21210 |
| Деталь: | GEAR Z16S |
| Парткод: | 2BG21190 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GEAR Z44S-Z53S-Z36S |
| Парткод: | 2BG21121 |
| Деталь: | GEAR 26,CLUTCH |
| Парткод: | 45727303 |
| Деталь: | GEAR Z15S-Z20S |
| Парткод: | 2BG21130 |
| Деталь: | GEAR 28,JOINT |
| Парткод: | 45728116 |
| Деталь: | GUIDE,TRAILING EDGE TAPPING |
| Парткод: | 2AC07270 |
| Деталь: | STOPPER,TRAILING EDGE TAPPING |
| Парткод: | 68721720 |
| Деталь: | RIGHT GUIDE,MIDDLE TRAY |
| Парткод: | 68721771 |
| Деталь: | MAGNET, CARTRIDGE |
| Парткод: | 65973030 |
| Деталь: | RIGHT LABEL,MIDDLE TRAY RELEASE |
| Парткод: | 68705040 |
| Деталь: | PCB DUPLEX ASSY |
| Парткод: | 2BG01180 |
| Деталь: | COVER DU PWB |
| Парткод: | 2BG21870 |
| Деталь: | WIRE,DUPLEX UNIT |
| Парткод: | 2BG28540 |
| Деталь: | SPRING EARTH DU |
| Парткод: | 2BG21220 |
| Деталь: | BKT COVER CASSETTE |
| Парткод: | 2BG21110 |
| Деталь: | PLATE COVER DU |
| Парткод: | 2BG21900 |
| Деталь: | SLIDER,DECK |
| Парткод: | 2BC07680 |
| Деталь: | COVER CASSETTE |
| Парткод: | 2BG07010 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 2BL04160 |
| Деталь: | SHAFT,REFEED PULLEY |
| Парткод: | 2AC07090 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | RIGHT PULLEY, FEED |
| Парткод: | 33906660 |
| Деталь: | UPPER GUIDE,DUPLEX REFEED |
| Парткод: | 2AC07102 |
| Деталь: | SPRING,FEED |
| Парткод: | 2AC07450 |
| Деталь: | COVER DU F |
| Парткод: | 2BG21950 |
| Деталь: | SHAFT DU CLUTCH |
| Парткод: | 2BG21200 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | SEET DU GUIDE |
| Парткод: | 2BG07360 |
| Деталь: | CLUTCH DU |
| Парткод: | 2BG21100 |
| Деталь: | PULLEY Z48 |
| Парткод: | 2BG21140 |
| Деталь: | POLYSLIDER CUT WASHER 7 |
| Парткод: | 2BG02850 |
| Деталь: | PLATE SIZE IN |
| Парткод: | 2BG07020 |
| Деталь: | PLATE SIZE C |
| Парткод: | 2BL06470 |
| Деталь: | PLATE NUMBER |
| Парткод: | 3CY04100 |
| Деталь: | Label 2 |
| Парткод: | 3CY05010 |
| Деталь: | MOUNT,SLIDER |
| Парткод: | 3HR02100 |
| Деталь: | CONTACT GLASS,ADF |
| Парткод: | 2CX12010 |
| Деталь: | PARTS,ASSY ISU(SP) |
| Парткод: | 2CX93141 |
| Деталь: | PULLEY.SCANNER DRUM |
| Парткод: | 2A612380 |
| Деталь: | PARTS,WIRE SCANNER(SP) |
| Парткод: | 2A693070 |
| Деталь: | SHAFT,WIRE DRUM |
| Парткод: | 2A612090 |
| Деталь: | BEARING.688ZZNR |
| Парткод: | 28107400 |
| Деталь: | STOPPER 7,CARTRIDGE |
| Парткод: | 33973300 |
| Деталь: | PULLEY 20/64 |
| Парткод: | 2BG12460 |
| Деталь: | PULLEY A,SCANNER WIRE |
| Парткод: | 35912040 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | HOLDER,ADF CONTACT GLASS |
| Парткод: | 2AV12300 |
| Деталь: | ADJUSTING PLATE,PULLEY |
| Парткод: | 2A612290 |
| Деталь: | SCANNER DRIVE PULLEY 40 |
| Парткод: | 2BG12440 |
| Деталь: | AUXILIARY PLATE,ORIGINAL HOLDER |
| Парткод: | 2A612230 |
| Деталь: | BELT SCANNER 176 |
| Парткод: | 2BG12450 |
| Деталь: | MOTOR,SCANNER |
| Парткод: | 2A612270 |
| Деталь: | MOUNT,SCANNER MOTOR |
| Парткод: | 2A612160 |
| Деталь: | BELT A,SCANNER |
| Парткод: | 2A612300 |
| Деталь: | MIRROR FRAME,SCANNER |
| Парткод: | 2A612131 |
| Деталь: | GUIDE FILM FFC |
| Парткод: | 2A612620 |
| Деталь: | ADJUSTING PLATE,MIRROR FRAME PULLEY |
| Парткод: | 2A612250 |
| Деталь: | SLIDER,SCANNER |
| Парткод: | 18512090 |
| Деталь: | MIRROR B,SCANNER |
| Парткод: | 2A612140 |
| Деталь: | MIRROR HOLDER |
| Парткод: | 75712080 |
| Деталь: | SPRING,SCANNER |
| Парткод: | 2A612400 |
| Деталь: | MIRROR A,SCANNER |
| Парткод: | 2A612120 |
| Деталь: | SPRING,MIRROR HOLDER |
| Парткод: | 35912210 |
| Деталь: | PARTS,PCB INVERTER(SP) |
| Парткод: | 2A693060 |
| Деталь: | SPACER,INVERTER PCB |
| Парткод: | 2A612260 |
| Деталь: | MOUNT BASE,LAMP |
| Парткод: | 2A612110 |
| Деталь: | PARTS,LAMP SCANNER(SP) |
| Парткод: | 2A693020 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE,LAMP INVERTER |
| Парткод: | 2CX27370 |
| Деталь: | GUIDE FFC1 |
| Парткод: | 2AV12080 |
| Деталь: | UPPER SHIELD,SCANNER |
| Парткод: | 2A612470 |
| Деталь: | RETAINER,WIRE |
| Парткод: | 35912140 |
| Деталь: | FEED GUIDE,SCANNER WIRE |
| Парткод: | 2A612180 |
| Деталь: | SENSOR,ORIGINAL DETECTION |
| Парткод: | 35927290 |
| Деталь: | WIRE,SCANNER UNIT |
| Парткод: | 2CX27130 |
| Деталь: | LOWER GRAND PLATE,SCANNER |
| Парткод: | 2A626150 |
| Деталь: | PULLEY SCANNER WIRE |
| Парткод: | 2A612480 |
| Деталь: | REINFORCEMENT,ORIGINAL HOLDER |
| Парткод: | 2A612220 |
| Деталь: | MOUNT SCANNER SW L |
| Парткод: | 2BG12350 |
| Деталь: | SWITCH,FEED |
| Парткод: | 35327400 |
| Деталь: | CORE 15-26X13 |
| Парткод: | 2AV27440 |
| Деталь: | MOUNT SCANNER SW R |
| Парткод: | 2BG12360 |
| Деталь: | GUIDE,RELEASE SWITCH |
| Парткод: | 2AC12360 |
| Деталь: | SWITCH,RELEASE DETECTION |
| Парткод: | 2AC12370 |
| Деталь: | SPRING.RELEASE SWITCH |
| Парткод: | 2AC12380 |
| Деталь: | COVER,SCANNER DRIVE |
| Парткод: | 2A612340 |
| Деталь: | CUSHION,CONTACT GLASS |
| Парткод: | 29812291 |
| Деталь: | COVER,ISU |
| Парткод: | 2A612241 |
| Деталь: | LABEL,CAUTION CONTACT GLASS |
| Парткод: | 2A105180 |
| Деталь: | REFLECTOR,SCANNER |
| Парткод: | 2A612410 |
| Деталь: | VIBRATION INSULATOR,MIRROR |
| Парткод: | 2A612450 |
| Деталь: | LID,NIC |
| Парткод: | 2A626120 |
| Деталь: | HOLDER,JOINT |
| Парткод: | 33921200 |
| Деталь: | SHEET B,INVERTER PCB |
| Парткод: | 2A612460 |
| Деталь: | PIN,TENSHION(M4) |
| Парткод: | 2A612370 |
| Деталь: | SCANNER JUNCTION ASSY |
| Парткод: | 2BG01090 |
| Деталь: | FRONT SEAL,CONTACT GLASS |
| Парткод: | 2A612350 |
| Деталь: | SPONGE,ORIGINAL SIZE INDICATOR |
| Парткод: | 35912531 |
| Деталь: | LEFT ORIGINAL SIZE INDICATOR |
| Парткод: | 2A612200 |
| Деталь: | STANDARD PLATE,SHADING |
| Парткод: | 2A612210 |
| Деталь: | LABEL,ORIGINAL SIZE INDICATOR(METRIC) |
| Парткод: | 2AV12481 |
| Деталь: | LABEL,ORIGINAL SIZE INDICATOR(INCH) |
| Парткод: | 2AV12491 |
| Деталь: | CONTACT GLASS |
| Парткод: | 2CJ12040 |
| Деталь: | REAR ORIGINAL SIZE INDICATOR(METRIC) |
| Парткод: | 2AV12460 |
| Деталь: | REAR ORIGINAL SIZE INDICATOR(INCH) |
| Парткод: | 2AV12470 |
| Деталь: | SPRING MOUNT SCANNER |
| Парткод: | 2BG12340 |
| Деталь: | WIRE,KEY COUNTER |
| Парткод: | 2BG27700 |
| Деталь: | SHIELD GASKET B |
| Парткод: | 2BG28960 |
| Деталь: | WIRE SADDLE,LWS-3S(KITAGAWA) |
| Парткод: | M2109230 |
| Деталь: | CORE,FRC-16-12-5 |
| Парткод: | 2BG28920 |
| Деталь: | SET,MK810A(U)(OPTION) |
| Парткод: | 2BF82120 |
| Деталь: | OZON FILTER |
| Парткод: | 2BG23030 |
| Деталь: | PARTS,FK-810(U) |
| Парткод: | 2BF93020 |
| Деталь: | PARTS,TR-810 |
| Парткод: | 2BF93066 |
| Деталь: | SET,MK810B(U)(OPTION) |
| Парткод: | 2BF82150 |
| Деталь: | PARTS,DK-810 |
| Парткод: | 2BF93112 |
| Деталь: | PARTS,DV-810K(U) |
| Парткод: | 2BG93180 |
| Деталь: | SET,MK810C(U)(OPTION) |
| Парткод: | 2BF82170 |
| Деталь: | PARTS,DV-810Y(U) |
| Парткод: | 2BG93121 |
| Деталь: | PARTS,DV-810M(U) |
| Парткод: | 2BG93141 |
| Деталь: | PARTS,DV-810C(U) |
| Парткод: | 2BG93161 |
| Деталь: | SET,MK815A(E)(OPTION) |
| Парткод: | 2BG82130 |
| Деталь: | PARTS,FK-815(E) |
| Парткод: | 2BG93050 |
| Деталь: | PARTS,TR-815 |
| Парткод: | 2BG93086 |
| Деталь: | SET,MK815B(J/E)(OPTION) |
| Парткод: | 2BG82140 |
| Деталь: | PARTS,DV-810K(J/E) |
| Парткод: | 2BG93170 |
| Деталь: | PARTS,DK-815 |
| Парткод: | 2BG93192 |
| Деталь: | SET,MK815C(J/E)(OPTION) |
| Парткод: | 2BG82160 |
| Деталь: | PARTS,DV-810Y(J/E) |
| Парткод: | 2BG93111 |
| Деталь: | PARTS,DV-810M(J/E) |
| Парткод: | 2BG93131 |
| Деталь: | PARTS,DV-810C(J/E) |
| Парткод: | 2BG93151 |
| Деталь: | BASE,RUBBER |
| Парткод: | 66102140 |
| Деталь: | BINDING TAP-TIGHT S SCREW M4X14 |
| Парткод: | B3024140 |
| Деталь: | COVER,KEY COUNTER |
| Парткод: | 2A360010 |
| Деталь: | RETAINER,KEY COUNTER |
| Парткод: | 66060030 |
| Деталь: | PLATE KEY COUNTER |
| Парткод: | 2BG60120 |
| Деталь: | MOUNT,KEY COUNTER |
| Парткод: | 66060040 |
| Деталь: | SOCKET ASSY.KEY COUNTER |
| Парткод: | 41529210 |
| Деталь: | TRIPLE SCREW M4X6 (BLACK) |
| Парткод: | B4304060 |
| Деталь: | COUNTER-SUNK HEAD SCREW BFHM3X6 (BLACK) |
| Парткод: | B2303060 |
| Деталь: | NUT BNM3 (BLACK) |
| Парткод: | C2303000 |
| Деталь: | SHIELD GASKET H |
| Парткод: | 2BG60270 |
| Деталь: | SHIELD GASKET J |
| Парткод: | 2BG60280 |
| Деталь: | CLAMP,EMT-6N(TAKEUCHI) |
| Парткод: | M7005020 |
| Деталь: | CLAMP,EMT-5N(TAKEUCHI) |
| Парткод: | M7005030 |
| Деталь: | EXIT SEPA ASSY |
| Парткод: | 2BG00450 |
| Деталь: | FRAME DECURLER |
| Парткод: | 2BG21810 |
| Деталь: | PULLEY PAPA-20 |
| Парткод: | 3DR02330 |
| Деталь: | SPRING SEPARATOR PULLEY |
| Парткод: | 2BG21450 |
| Деталь: | SPRING EARTH SEPA B |
| Парткод: | 2BG21440 |
| Деталь: | ROLLER SEPARATOR B |
| Парткод: | 2BG21510 |
| Деталь: | BUSH 6 EW |
| Парткод: | 2BG22970 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | PULLEY SEPARATOR 23 |
| Парткод: | 2BG21530 |
| Деталь: | BELT SEPARATOR |
| Парткод: | 2BG21560 |
| Деталь: | DU CONVEYANCE A ASSY |
| Парткод: | 2BG00460 |
| Деталь: | GUIDE DU A |
| Парткод: | 2BG21720 |
| Деталь: | SPRING DU A |
| Парткод: | 2BG21840 |
| Деталь: | PLATE GUIDE DU A |
| Парткод: | 2BG21600 |
| Деталь: | DU CONVEYANCE B ASSY |
| Парткод: | 2BG00470 |
| Деталь: | GUIDE DU B |
| Парткод: | 2BG21730 |
| Деталь: | ROLLER PINCH43397A0045 |
| Парткод: | 2BS04170 |
| Деталь: | SPRING PULLEY43397A0048 |
| Парткод: | 2BS04050 |
| Деталь: | SPRING DU B |
| Парткод: | 2BG21910 |
| Деталь: | PLATE GUIDE DU B |
| Парткод: | 2BG21640 |
| Деталь: | ROLLER DU |
| Парткод: | 2BG21520 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | SWITCH,PHOT0 interruptor |
| Парткод: | 2A127050 |
| Деталь: | ACTUATOR DU |
| Парткод: | 2BG21920 |
| Деталь: | WIRE.DUPLEX SWITCH |
| Парткод: | 2BG27820 |
| Деталь: | GEAR 16,BYPASS |
| Парткод: | 29807100 |
| Деталь: | IDLE GEAR 18 BYPASS |
| Парткод: | 78307310 |
| Деталь: | COVER PULLEY40633D0095 |
| Парткод: | 2CW22160 |
| Деталь: | DISCHARGER FD |
| Парткод: | 2A816511 |
| Деталь: | MINIATURE CLAMP,UAMS-07-0 |
| Парткод: | M2105730 |
| Деталь: | DU EXIT GUIDE ASSY |
| Парткод: | 2BG00481 |
| Деталь: | GUIDE DU UP |
| Парткод: | 2BG07200 |
| Деталь: | LOWER GUIDE,DUPLEX FEED |
| Парткод: | 68707021 |
| Деталь: | EXIT ASSY |
| Парткод: | 2BG00432 |
| Деталь: | GUIDE EXIT(1/4) |
| Парткод: | 2BG21460 |
| Деталь: | SHEET EXIT GUIDE |
| Парткод: | 2BG21660 |
| Деталь: | SEAL EXIT B |
| Парткод: | 2BG21650 |
| Деталь: | TAPE DIS JOINT |
| Парткод: | 2BG21610 |
| Деталь: | TAPE DIS JOINT CE |
| Парткод: | 2BG21620 |
| Деталь: | DISCHARGER EXIT |
| Парткод: | 2BG21060 |
| Деталь: | SOLENOID FEED |
| Парткод: | 2BG21430 |
| Деталь: | PLATE SOLENOID |
| Парткод: | 2BG21790 |
| Деталь: | SPRING SOLENOID |
| Парткод: | 2BM17220 |
| Деталь: | STUD SCREW M3 |
| Парткод: | 2BR20470 |
| Деталь: | SPRING JOINT EXIT |
| Парткод: | 2BG21860 |
| Деталь: | PLATE GUIDE R |
| Парткод: | 2BG21710 |
| Деталь: | SPRING PULLEY FU |
| Парткод: | 2BG21290 |
| Деталь: | SHAFT PULLEY EXIT B |
| Парткод: | 2BG21090 |
| Деталь: | PULLEY EXIT |
| Парткод: | 2BG21070 |
| Деталь: | PULLEY EXIT FU |
| Парткод: | 2BG21540 |
| Деталь: | ACTUATOR FUSER EXIT |
| Парткод: | 2BG21761 |
| Деталь: | ACT FUSER DU |
| Парткод: | 2BG21260 |
| Деталь: | ROLLER EXIT SPG |
| Парткод: | 2BG21740 |
| Деталь: | BEARING.DRIVE |
| Парткод: | 2AV22410 |
| Деталь: | ROLLER EXIT E |
| Парткод: | 2BG21050 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | ROLLER EXIT C |
| Парткод: | 2BG21030 |
| Деталь: | BUSH 6 EW |
| Парткод: | 2BG22970 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | GEAR Z42 EXIT B |
| Парткод: | 2BG07430 |
| Деталь: | PULLEY SEPARATOR 23 B |
| Парткод: | 2BG07420 |
| Деталь: | GEAR Z21-Z20 EXIT |
| Парткод: | 2BG21160 |
| Деталь: | GEAR Z20 EXIT B |
| Парткод: | 2BG07410 |
| Деталь: | GUIDE CHANGE DU |
| Парткод: | 2BG21831 |
| Деталь: | WIRE,EJECT UNIT |
| Парткод: | 2BG27970 |
| Деталь: | SWITCH,PHOT0 interruptor |
| Парткод: | 2A127050 |
| Деталь: | SPONGE EXIT FRAME |
| Парткод: | 2BG21630 |
| Деталь: | SPRING EARTH JOINT |
| Парткод: | 2BG21700 |
| Деталь: | SPRING FUSER ACT DU |
| Парткод: | 2BG21490 |
| Деталь: | ACTUATOR EXIT B |
| Парткод: | 2BG21380 |
| Деталь: | SPRING ACT FU |
| Парткод: | 2BG21980 |
| Деталь: | GUIDE CHANGE FD |
| Парткод: | 2BG21821 |
| Деталь: | COVER EXIT |
| Парткод: | 2BG21230 |
| Деталь: | SEAL EXIT A |
| Парткод: | 2BG21670 |
| Деталь: | HANDLE EXIT |
| Парткод: | 2BG21960 |
| Деталь: | SEAL EXIT C |
| Парткод: | 2BG21990 |
| Деталь: | SPRING HOOK FUSER |
| Парткод: | 2BG20790 |
| Деталь: | SPRING HOOK EXIT |
| Парткод: | 2BG21550 |
| Деталь: | LABEL OPERATION LEFT |
| Парткод: | 2BG05060 |
| Деталь: | PLATE LEVER SOL |
| Парткод: | 2BM17180 |
| Деталь: | SHEET EXIT COVER |
| Парткод: | 2BG07610 |
| Деталь: | SPRING EXIT F |
| Парткод: | 2BG21470 |
| Деталь: | PLATE EXIT COVER |
| Парткод: | 2BG21300 |
| Деталь: | SPRING EXIT R |
| Парткод: | 2BG21480 |
| Деталь: | MOTOR B,LIFT CASSETTE |
| Парткод: | 2BC27120 |
| Деталь: | FUSER DRIVE ASSY |
| Парткод: | 2BG00550 |
| Деталь: | PLATE DRIVE FUSER |
| Парткод: | 2BG22100 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | SPRING JOINT F |
| Парткод: | 2BG22190 |
| Деталь: | GEAR Z120H-Z34P |
| Парткод: | 2BG22490 |
| Деталь: | GEAR Z37H |
| Парткод: | 2BG22460 |
| Деталь: | BELT DU |
| Парткод: | 2BG22480 |
| Деталь: | GEAR Z60H |
| Парткод: | 2BG22070 |
| Деталь: | GEAR Z97H-Z35S |
| Парткод: | 2BG22180 |
| Деталь: | GEAR Z34S-Z33H |
| Парткод: | 2BG22120 |
| Деталь: | GEAR Z28S-Z20H |
| Парткод: | 2BG22160 |
| Деталь: | GEAR Z56H-Z50S |
| Парткод: | 2BG22110 |
| Деталь: | GEAR Z22S EJ |
| Парткод: | 2BG22700 |
| Деталь: | GEAR Z35S EJ |
| Парткод: | 2BG22130 |
| Деталь: | SHAFT FUSER CLUTCH |
| Парткод: | 2BG22560 |
| Деталь: | GEAR,DEVELOPING SPIRAL |
| Парткод: | 68314090 |
| Деталь: | GEAR Z46H |
| Парткод: | 2BG22150 |
| Деталь: | GEAR Z26S |
| Парткод: | 2BG22140 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | SWITCH,INTERLOCK |
| Парткод: | 2AV27370 |
| Деталь: | WIRE,FUSER MOTOR |
| Парткод: | 2BG27290 |
| Деталь: | HOLDER GEAR |
| Парткод: | 2BG22090 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | CLUTCH FUSER |
| Парткод: | 2BG22650 |
| Деталь: | PLATE CLUTCH FUSER |
| Парткод: | 2BG22910 |
| Деталь: | MOTOR,FIXING |
| Парткод: | 2BG27140 |
| Деталь: | MINIATURE CLAMP,UAMS-07-0 |
| Парткод: | M2105730 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | LOCKING WIRE SADDLE,LWS-4NS |
| Парткод: | 49828500 |
| Деталь: | WIRE,MC PCB |
| Парткод: | 2BG27310 |
| Деталь: | PLATE DRIVE DU |
| Парткод: | 2BG22440 |
| Деталь: | SHAFT DU |
| Парткод: | 2BG22450 |
| Деталь: | GEAR Z45S-Z28S |
| Парткод: | 2BG22510 |
| Деталь: | GEAR Z36P-Z34S |
| Парткод: | 2BG22500 |
| Деталь: | GEAR Z33S DU |
| Парткод: | 2BG22710 |
| Деталь: | GEAR Z38S DU |
| Парткод: | 2BG22470 |
| Деталь: | GEAR Z29 EXIT |
| Парткод: | 2BG21420 |
| Деталь: | ASSY.PCB ENVIRONMENT SENSOR |
| Парткод: | 2BG01200 |
| Деталь: | DUCT COOLING |
| Парткод: | 2BG23010 |
| Деталь: | MCH HV PWB |
| Парткод: | 2BG28060 |
| Деталь: | STAY DUCT |
| Парткод: | 2BG26300 |
| Деталь: | DUCT MCH |
| Парткод: | 2BG10150 |
| Деталь: | EDGING, EDS-2323U(KITAGAWA) |
| Парткод: | M2104270 |
| Деталь: | DUCT COOLING FAN |
| Парткод: | 2BG23020 |
| Деталь: | FAN 92X25-300 |
| Парткод: | 2BG27550 |
| Деталь: | FAN 80X25-100 |
| Парткод: | 2BG27790 |
| Деталь: | BRACKET FAN |
| Парткод: | 2BG10140 |
| Деталь: | SEAL DUCT MCH |
| Парткод: | 2BG10170 |
| Деталь: | WIRE,MC HIGH VOLTAGE M |
| Парткод: | 2BG27920 |
| Деталь: | WIRE,MC HIGH VOLTAGE C |
| Парткод: | 2BG28660 |
| Деталь: | WIRE,MC HIGH VOLTAGE Y |
| Парткод: | 2BG28670 |
| Деталь: | WIRE,MC HIGH VOLTAGE K |
| Парткод: | 2BG28680 |
| Деталь: | PARTS,CASSETTE ASSY.SP |
| Парткод: | 2BG93011 |
| Деталь: | RACKCURSOR |
| Парткод: | 3CY06090 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 2BC07860 |
| Деталь: | RAIL A,CURSOR |
| Парткод: | 2BC06720 |
| Деталь: | CURSOR A,CASSETTE |
| Парткод: | 3CY06041 |
| Деталь: | LEVER,CASSETTE CURSOR |
| Парткод: | 33907080 |
| Деталь: | SPRING,CURSOR |
| Парткод: | 2BC06950 |
| Деталь: | LID A,CURSOR |
| Парткод: | 3CY06060 |
| Деталь: | CUSHION,CASSETTE R |
| Парткод: | 60907170 |
| Деталь: | CURSOR B,CASSETTE |
| Парткод: | 3CY06050 |
| Деталь: | LABEL,PAPER UPPER LIMIT |
| Парткод: | 61705110 |
| Деталь: | GEAR 20,CURSOR |
| Парткод: | 3CY06100 |
| Деталь: | SIZE DETECTION PCB |
| Парткод: | 33928111 |
| Деталь: | WIRE,CASSETTE UNIT |
| Парткод: | 33927210 |
| Деталь: | SHAFT,LIFT CASSETTE |
| Парткод: | 2BC06710 |
| Деталь: | WORK PLATE,LIFT CASSETTE |
| Парткод: | 2BC06090 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | RETAINER M4 |
| Парткод: | 3CY06030 |
| Деталь: | WORK PLATE,CASSETTE |
| Парткод: | 33907020 |
| Деталь: | PAD,CASSETTE |
| Парткод: | 66107100 |
| Деталь: | PIN,CASSETTE WORK PLATE |
| Парткод: | 66007310 |
| Деталь: | CURSOR C,CASSETTE |
| Парткод: | 3CY06071 |
| Деталь: | LID C,CURSOR |
| Парткод: | 3CY06080 |
| Деталь: | RAIL C,CURSOR |
| Парткод: | 33907120 |
| Деталь: | DETECTION PLATE,PAPER SIZE |
| Парткод: | 33907170 |
| Деталь: | SPRING.PAD |
| Парткод: | 66106080 |
| Деталь: | LID,PAPER SIZE DETECTION |
| Парткод: | 33907160 |
| Деталь: | GROUND PLATE,CASSETTE |
| Парткод: | 2BC07830 |
| Деталь: | PLUG,QR/P15-8S-C(HIROSE) |
| Парткод: | J0463080 |
| Деталь: | LABEL,CASSETTE |
| Парткод: | 3CY05080 |
| Деталь: | SHEET,LIFT PLATE |
| Парткод: | 3CY06110 |
| Деталь: | PARTS,CASSETTE COVER,SP |
| Парткод: | 2BG93020 |
| Деталь: | Label 1 |
| Парткод: | 2BG05070 |
| Деталь: | PLATE SIZE C |
| Парткод: | 2BL06470 |
| Деталь: | PLATE SIZE IN |
| Парткод: | 2BL06910 |
| Деталь: | PLATE NUMBER |
| Парткод: | 3CY04100 |
| Деталь: | SPACER PILOT PIN |
| Парткод: | 2BG09360 |
| Деталь: | PLATE PILOT PIN |
| Парткод: | 2BG09120 |
| Деталь: | HANDLE |
| Парткод: | 2BG02180 |
| Деталь: | CAP HANDLE |
| Парткод: | 2BG02470 |
| Деталь: | CAP HANDLER |
| Парткод: | 2BG02480 |
| Деталь: | GUIDE TC F |
| Парткод: | 2BG02600 |
| Деталь: | PULLEY RAIL B |
| Парткод: | 2BG02770 |
| Деталь: | LEVER LOCKTCF |
| Парткод: | 2BG02620 |
| Деталь: | PIN LOCK TC |
| Парткод: | 2BG02650 |
| Деталь: | SPRING COVER R |
| Парткод: | 3B706550 |
| Деталь: | LOCK COVER R |
| Парткод: | 2BL06490 |
| Деталь: | HUM SENSOR F |
| Парткод: | 2BG28250 |
| Деталь: | WIRE,F HUM SENSOR |
| Парткод: | 2BG28800 |
| Деталь: | HOLDER HV DLP |
| Парткод: | 2BG09130 |
| Деталь: | SPRING HV DLP |
| Парткод: | 2BG09160 |
| Деталь: | PLATE HV DLP A |
| Парткод: | 2BG09140 |
| Деталь: | SENSOR WASTE |
| Парткод: | 2BG18520 |
| Деталь: | WIRE,WASTE SENSOR |
| Парткод: | 2BG27200 |
| Деталь: | WIRE,DB HIGH VOLTAGE |
| Парткод: | 2BG27850 |
| Деталь: | SPRING LOCK TC |
| Парткод: | 2BG02640 |
| Деталь: | PIN HOOK |
| Парткод: | 2BG02400 |
| Деталь: | SPRING EARTH RAIL |
| Парткод: | 2BG06710 |
| Деталь: | STOPPER FEED UNIT |
| Парткод: | 2BG06970 |
| Деталь: | MINIATURE CLAMP,UAMS-07-0 |
| Парткод: | M2105730 |
| Деталь: | SLIDER,DECK |
| Парткод: | 2BC07680 |
| Деталь: | PLATE RAIL R |
| Парткод: | 2BG02060 |
| Деталь: | RAIL CASSETTE R |
| Парткод: | 2BG06900 |
| Деталь: | WIRE,HERTER |
| Парткод: | 2BG27780 |
| Деталь: | HOOK CASSETTE |
| Парткод: | 2BG06420 |
| Деталь: | SPRING CASS HOOK |
| Парткод: | 2BG06720 |
| Деталь: | PLATE RAIL L |
| Парткод: | 2BG02070 |
| Деталь: | RAIL CASSETTE L |
| Парткод: | 2BG06910 |
| Деталь: | SHEET HARNESS TC |
| Парткод: | 2BG02500 |
| Деталь: | RAIL CASSETTE C |
| Парткод: | 2BG06430 |
| Деталь: | SPRING A |
| Парткод: | 2BG02720 |
| Деталь: | RAIL FUSER F |
| Парткод: | 2BG02220 |
| Деталь: | PULLEY RAIL |
| Парткод: | 2BG02240 |
| Деталь: | PIN PULLEY |
| Парткод: | 2BG20350 |
| Деталь: | PLATE MIDDLE L |
| Парткод: | 2BG02460 |
| Деталь: | STAY MIDDLE |
| Парткод: | 2BG02450 |
| Деталь: | WIRE,T UNIT JUNCTION A |
| Парткод: | 2BG28500 |
| Деталь: | WIRE,T UNIT JUNCTION B |
| Парткод: | 2BG28700 |
| Деталь: | SCREW A |
| Парткод: | 2BG02410 |
| Деталь: | WIRE,FUSER JUNCTION |
| Парткод: | 2BG27540 |
| Деталь: | WASTE TONER ASSY |
| Парткод: | 2BG00330 |
| Деталь: | TRAY WASTE |
| Парткод: | 2BG18320 |
| Деталь: | JOINT WASTE |
| Парткод: | 2BG18470 |
| Деталь: | BRACKET TB DRIVE |
| Парткод: | 2BG18480 |
| Деталь: | WORM WHEEL Z34S-Z15H |
| Парткод: | 2BG18490 |
| Деталь: | WIRE,TONER BOTTLE CHECK |
| Парткод: | 2BG27940 |
| Деталь: | WIRE,MOTOR BOTTLE |
| Парткод: | 2BG28650 |
| Деталь: | GEAR WORM |
| Парткод: | 2BM14540 |
| Деталь: | DC motor |
| Парткод: | 2BM27340 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | WASTE TONER BOX ASSY |
| Парткод: | 2BG00342 |
| Деталь: | SHEET EXIT SWITCH |
| Парткод: | 2BG02750 |
| Деталь: | PRIMARY FEED ASSY |
| Парткод: | 2BG00130 |
| Деталь: | SHAFT FEED UP |
| Парткод: | 2BG06780 |
| Деталь: | UPPER GEAR,PAPER FEED |
| Парткод: | 2BC06790 |
| Деталь: | PULLEY,PAPER FEED |
| Парткод: | 2BC06900 |
| Деталь: | BUSHING,BYPASS SHAFT |
| Парткод: | 60907880 |
| Деталь: | UPPER HOUSING,PAPER FEED |
| Парткод: | 2BC06010 |
| Деталь: | BUSHING,PAPER FEED |
| Парткод: | 36706310 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | PLATE FEED F |
| Парткод: | 2BG06360 |
| Деталь: | LOWER HOUSING.PAPER FEED |
| Парткод: | 2BC06021 |
| Деталь: | LOWER REINFORCEMENT,HOUSING PAPER FEED |
| Парткод: | 2BC06360 |
| Деталь: | VIBRATION INSULATOR,RELEASE LEVER |
| Парткод: | 33906211 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 2BG06990 |
| Деталь: | TORQUE LIMITER 360 |
| Парткод: | 2BG06380 |
| Деталь: | LOWER PULLEY.PAPER FEED |
| Парткод: | 33906060 |
| Деталь: | LOWER LEVER,PAPER FEED PULLEY RELEASE |
| Парткод: | 33906090 |
| Деталь: | BUSHING,6 |
| Парткод: | 63806290 |
| Деталь: | LOWER SPRING B,PAPER FEED |
| Парткод: | 3CY06020 |
| Деталь: | PLATE FEED R |
| Парткод: | 2BG06370 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | LOWER BUSHING.PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | STOPPER 5,RING |
| Парткод: | 2BC06990 |
| Деталь: | COVER DRIVE FEED |
| Парткод: | 2BG06980 |
| Деталь: | GEAR FEED Z33S |
| Парткод: | 2BG06790 |
| Деталь: | GUIDE,CONFLUENCE |
| Парткод: | 2BC06460 |
| Деталь: | SHAFT,LEADING FEED PULLEY |
| Парткод: | 33906080 |
| Деталь: | WIRE,PAPER FEED UNIT |
| Парткод: | 2BG27270 |
| Деталь: | SWITCH PI |
| Парткод: | 2BL27450 |
| Деталь: | ACTUATOR,PAPER EMPTY |
| Парткод: | 2BC06380 |
| Деталь: | SUPPORT PLATE,LEADING FEED PULLEY |
| Парткод: | 2BC06300 |
| Деталь: | WEIGHT,LEADING FEED PULLEY |
| Парткод: | 33906180 |
| Деталь: | GEAR 18,RETARD |
| Парткод: | 34922220 |
| Деталь: | STOP RING,4 |
| Парткод: | 63511220 |
| Деталь: | PULLEY,LEADING FEED |
| Парткод: | 2BC06810 |
| Деталь: | STAY FUSER |
| Парткод: | 2BG02260 |
| Деталь: | SPRING HOOK |
| Парткод: | 2BG20800 |
| Деталь: | SLIDER FUSER F |
| Парткод: | 2BG02270 |
| Деталь: | PULLEY SLIDER |
| Парткод: | 2BG20340 |
| Деталь: | PIN PULLEY |
| Парткод: | 2BG20350 |
| Деталь: | SLIDER FUSER R |
| Парткод: | 2BG02280 |
| Деталь: | HOOK FUSER LOCK |
| Парткод: | 2BG20750 |
| Деталь: | PARTS,FK-810(U) |
| Парткод: | 2BF93020 |
| Деталь: | PARTS,FK-815(E) |
| Парткод: | 2BG93050 |
| Деталь: | LABEL CAUTION FUSER |
| Парткод: | 2BG05010 |
| Деталь: | FRAME ROLLER LOW |
| Парткод: | 2BG20060 |
| Деталь: | THERMOSTAT 150 |
| Парткод: | 2BG20910 |
| Деталь: | PIN PRESSURE |
| Парткод: | 2BG20120 |
| Деталь: | SPRING PRESS FUSER |
| Парткод: | 2BG20130 |
| Деталь: | MOUNT THERMISTOR LOW |
| Парткод: | 2BG20870 |
| Деталь: | THERMISTOR UP |
| Парткод: | 2BG20580 |
| Деталь: | ROLLER HEAT LOW |
| Парткод: | 2BG20020 |
| Деталь: | STOPPER FUSER B |
| Парткод: | 2BG20900 |
| Деталь: | BUSH HEAT ROLLER |
| Парткод: | 2CK20040 |
| Деталь: | BEARING FUSER |
| Парткод: | 2BG20150 |
| Деталь: | FRAME FUSER |
| Парткод: | 2BG20030 |
| Деталь: | WIRE,FUSER UNIT |
| Парткод: | 2BF27071 |
| Деталь: | WIRE,FUSER UNIT |
| Парткод: | 2BG27561 |
| Деталь: | HOLDER DRAWER |
| Парткод: | 2BG20360 |
| Деталь: | SHEET HARNESS A |
| Парткод: | 2BG20840 |
| Деталь: | ROLLER HEAT UP |
| Парткод: | 2BG20010 |
| Деталь: | GEAR FUSER Z38S |
| Парткод: | 2BG20140 |
| Деталь: | STOPPER FUSER |
| Парткод: | 2BG20880 |
| Деталь: | FRAME FUSER UP |
| Парткод: | 2BG20040 |
| Деталь: | THERMOSTAT 140 |
| Парткод: | 2BG20920 |
| Деталь: | GUIDE ENTRANCE UP |
| Парткод: | 2BG20080 |
| Деталь: | HOLDER HEATER R |
| Парткод: | 2BG20480 |
| Деталь: | PLATE FUSER HEATER |
| Парткод: | 2BG20590 |
| Деталь: | HOLDER HEATER F |
| Парткод: | 2BG20470 |
| Деталь: | PCB FIXING ASSY |
| Парткод: | 2BG01170 |
| Деталь: | LAMP HEATER UP 120 |
| Парткод: | 2BG20430 |
| Деталь: | LAMP HEATER UP 240 |
| Парткод: | 2BG20450 |
| Деталь: | LAMP HEATER LOW 120 |
| Парткод: | 2BG20440 |
| Деталь: | LAMP HEATER LOW 240 |
| Парткод: | 2BG20460 |
| Деталь: | SHEET HARNESSC |
| Парткод: | 2BG20860 |
| Деталь: | GUIDE ENTRANCE |
| Парткод: | 2BG20070 |
| Деталь: | GUIDE ENTRANCE LOW |
| Парткод: | 2BG20090 |
| Деталь: | COVER FUSER UP |
| Парткод: | 2BG20550 |
| Деталь: | GUIDE EXIT UP |
| Парткод: | 2BG20210 |
| Деталь: | SPRING FUSER EXIT |
| Парткод: | 2BG20890 |
| Деталь: | SHAFT EXIT |
| Парткод: | 2BG20330 |
| Деталь: | PULLY EXIT |
| Парткод: | 2BG20320 |
| Деталь: | STAY FUSER UP |
| Парткод: | 2BG20190 |
| Деталь: | COVER FUSER EXIT |
| Парткод: | 2BG20180 |
| Деталь: | SHAFT EXIT RELEASE |
| Парткод: | 2BG20290 |
| Деталь: | HOOK EXIT RELEASE |
| Парткод: | 2BG20600 |
| Деталь: | SPRING EXIT RELEASE |
| Парткод: | 2BG20310 |
| Деталь: | ROLLER FUSER EXIT |
| Парткод: | 2BG20270 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | BUSH 6 EW |
| Парткод: | 2BG22970 |
| Деталь: | GEAR Z17S EXIT |
| Парткод: | 2BG20510 |
| Деталь: | GUIDE EXIT LOW |
| Парткод: | 2BG20220 |
| Деталь: | TERMINAL EXIT ROLLER |
| Парткод: | 2BG20610 |
| Деталь: | COVER FUSER F |
| Парткод: | 2BG20560 |
| Деталь: | GEAR Z23S IDLE |
| Парткод: | 2BG20530 |
| Деталь: | COVER FUSER R |
| Парткод: | 2BG20570 |
| Деталь: | HANDLE FUSER |
| Парткод: | 2BG20540 |
| Деталь: | PIN HOOK |
| Парткод: | 2BG02400 |
| Деталь: | PLATE FEED L |
| Парткод: | 2BG06250 |
| Деталь: | MINIATURE CLAM P, U AMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | ROLLER FEED B |
| Парткод: | 2BG06240 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | BUSH 8 EW |
| Парткод: | 2BG22950 |
| Деталь: | SPONGE WIRE A |
| Парткод: | 2BG06500 |
| Деталь: | SWITCH,CONVEYING |
| Парткод: | 2BC27010 |
| Деталь: | WIRE,PAPER FEED JUNCTION |
| Парткод: | 2BG27320 |
| Деталь: | EDGING.EDS-2 |
| Парткод: | M2104210 |
| Деталь: | FEED UNIT ASSY |
| Парткод: | 2BG00633 |
| Деталь: | PLATE FEED LOW |
| Парткод: | 2BG06630 |
| Деталь: | LEVER FEED LOCK |
| Парткод: | 2BG06920 |
| Деталь: | FRAME FEED |
| Парткод: | 2BG06010 |
| Деталь: | WIRE,REGISTRATION SWITCH |
| Парткод: | 2BG27571 |
| Деталь: | SWITCH,PHOT0 interruptor |
| Парткод: | 2A127050 |
| Деталь: | ACTUATOR FEED |
| Парткод: | 2BG06870 |
| Деталь: | SPRING ACT FEED |
| Парткод: | 2BG06450 |
| Деталь: | SPRING ACT REG |
| Парткод: | 2BG06460 |
| Деталь: | SPRING EARTH FEED |
| Парткод: | 2BG06690 |
| Деталь: | LEVER FEED B |
| Парткод: | 2BG06110 |
| Деталь: | HOLDER EARTH PIN |
| Парткод: | 2BG07540 |
| Деталь: | PIN EARTH FEED |
| Парткод: | 2BG07530 |
| Деталь: | SPRING HOLDER PIN |
| Парткод: | 2BG07550 |
| Деталь: | PLATE EARTH REGIST |
| Парткод: | 2BG06930 |
| Деталь: | HIGHMEG ASSY |
| Парткод: | 2BG06640 |
| Деталь: | ROLLER FEED A |
| Парткод: | 2BG06060 |
| Деталь: | SPONGE WIRE D |
| Парткод: | 2BG06570 |
| Деталь: | GEAR Z19S |
| Парткод: | 2BG06320 |
| Деталь: | COVER ACT FEED |
| Парткод: | 2BG07500 |
| Деталь: | SHAFT FEED UNIT |
| Парткод: | 2BG06070 |
| Деталь: | HOOK FEED F |
| Парткод: | 2BG06080 |
| Деталь: | HOOK FEED R |
| Парткод: | 2BG06740 |
| Деталь: | SPRING FEED HOOK |
| Парткод: | 2BG06950 |
| Деталь: | STOPPER TC |
| Парткод: | 2BG06270 |
| Деталь: | SPRING PRESS TC |
| Парткод: | 2BG06400 |
| Деталь: | SPRING EARTH GUIDE |
| Парткод: | 2BG06410 |
| Деталь: | PLATE GUIDE REGIST LOW |
| Парткод: | 2BG06030 |
| Деталь: | ROLLER REGIST LOW |
| Парткод: | 2BG06050 |
| Деталь: | BUSH 6 NB |
| Парткод: | 2BG07520 |
| Деталь: | SHEET REGIST |
| Парткод: | 2BG06470 |
| Деталь: | PLATE GUIDE REGIST UP |
| Парткод: | 2BG06750 |
| Деталь: | SPRING REG RELEASE |
| Парткод: | 2BG06490 |
| Деталь: | ROLLER REGIST UP |
| Парткод: | 2BG06040 |
| Деталь: | BUSH REGIST UP NB |
| Парткод: | 2BG07510 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | SPRING REGIST A |
| Парткод: | 2BG06340 |
| Деталь: | SPRING REGIST B |
| Парткод: | 2BG07600 |
| Деталь: | GEAR Z15S |
| Парткод: | 2BG06330 |
| Деталь: | GEAR Z18S-Z22S |
| Парткод: | 2BG06170 |
| Деталь: | HOLDER FEED DRIVE |
| Парткод: | 2BG06100 |
| Деталь: | GEAR Z19S-Z26S |
| Парткод: | 2BG06180 |
| Деталь: | GEAR Z20S-Z24S |
| Парткод: | 2BG06770 |
| Деталь: | GEAR 21 |
| Парткод: | 3A821110 |
| Деталь: | MINIATURE CLAMP,UAMS-05-2 |
| Парткод: | M2105720 |
| Деталь: | RAIL FEED R |
| Парткод: | 2BG06310 |
| Деталь: | HOLDER TC R |
| Парткод: | 2BG06730 |
| Деталь: | RAIL FEED F |
| Парткод: | 2BG06301 |
| Деталь: | HOLDER TC F |
| Парткод: | 2BG06220 |
| Деталь: | COVER FEED |
| Парткод: | 2BG06190 |
| Деталь: | GUIDE FEED LOW |
| Парткод: | 2BG06230 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BG06161 |
| Деталь: | LEVER COVER FEED |
| Парткод: | 2BG06280 |
| Деталь: | SPRING COVER FEED |
| Парткод: | 2BG06660 |
| Деталь: | SHAFT FEED C |
| Парткод: | 2BG06290 |
| Деталь: | HANDLE FEED |
| Парткод: | 2BG06350 |
| Деталь: | SPRING HANDLE FEED |
| Парткод: | 2BG06260 |
| Деталь: | LEVER FEED A |
| Парткод: | 2BG06440 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 2BG07560 |
| Деталь: | SPRING FEED A |
| Парткод: | 2BG07570 |
| Деталь: | SHAFT FEED A |
| Парткод: | 2BG06140 |
| Деталь: | SET AK-640A(120)(OPTION) |
| Парткод: | 3B882050 |
| Деталь: | SET AK-640A(230)(OPTION) |
| Парткод: | 3B882060 |
| Деталь: | POWER CORD(120) |
| Парткод: | 19527400 |
| Деталь: | FILM,CONVEYING |
| Парткод: | 3B860560 |
| Деталь: | REAR RETAINER,SLIDER |
| Парткод: | 3B803510 |
| Деталь: | MOUNT,SLIDER |
| Парткод: | 3B803520 |
| Деталь: | JUNCTION PLATE,SLIDER |
| Парткод: | 3B803530 |
| Деталь: | JUNCTION PLATE,MACHINE |
| Парткод: | 3B803540 |
| Деталь: | MOUNT,MACHINE |
| Парткод: | 3B803550 |
| Деталь: | STOPPER,JUNCTION PLATE |
| Парткод: | 3B803560 |
| Деталь: | RAIL,RELEASE |
| Парткод: | 3B803570 |
| Деталь: | GROUND PLATE A,NOISE |
| Парткод: | 18526211 |
| Деталь: | FRONT RETAINER,SLIDER |
| Парткод: | 3B803500 |
| Деталь: | SLIDER,FINISHER |
| Парткод: | 3B803600 |
| Деталь: | HANDLE,RELEASE |
| Парткод: | 3B803610 |
| Деталь: | RETAINER M,RELEASE |
| Парткод: | 3B860510 |
| Деталь: | HOOK M,RELEASE |
| Парткод: | 3B860520 |
| Деталь: | GROUND PLATE,FIXING UNIT |
| Парткод: | 34920190 |
| Деталь: | ACTUATOR PLATE M,SAFETY SWITCH |
| Парткод: | 3B860530 |
| Деталь: | RAIL M,RELEASE |
| Парткод: | 3B860540 |
| Деталь: | JUNCTION PLATE M,RAIL |
| Парткод: | 3B860550 |
| Деталь: | OPTION BOX ASSY(120) |
| Парткод: | 2BG60080 |
| Деталь: | OPTION BOX ASSY(200) |
| Парткод: | 2BG60090 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | 49513902 |
| Деталь: | SPACER,MAIN PCB |
| Парткод: | 2A626300 |
| Деталь: | FAN,COOLING50 |
| Парткод: | 2BG27490 |
| Деталь: | OPTION POWER SUPPLY ASSY(100) |
| Парткод: | 2BG60031 |
| Деталь: | OPTION POWER SUPPLY ASSY(200) |
| Парткод: | 2BG60041 |
| Деталь: | WIRE,OPTION POWER SUPPLY |
| Парткод: | 2BG60050 |
| Деталь: | MOUNT OPTION POWER SOURCE |
| Парткод: | 2BG60060 |
| Деталь: | INLET ASSY |
| Парткод: | 2BG60200 |
| Деталь: | CORE,9-20X32 |
| Парткод: | 65027480 |
| Деталь: | BINDING TAP-TIGHT S SCREW M4X14 |
| Парткод: | B3024140 |
| Деталь: | +TP TAP-TITE S SCREW M4X20(TRIVALENT CHROMATING |
| Парткод: | BAB54200 |
| Деталь: | TRIPLE SCREW M3X5 (BLACK) |
| Парткод: | B4303050 |
| Деталь: | BINDING SCREW BVM4X6 (BLACK) |
| Парткод: | B1304060 |
| Деталь: | BINDING SCREW BVM4X10 (BLACK) |
| Парткод: | B1304100 |
| Деталь: | BINDING SCREW BVM3X5 (BLACK) |
| Парткод: | B1303050 |
| Деталь: | BINDING SCREW CVM3X5 |
| Парткод: | B1003050 |
| Деталь: | CORE SFT-72SNB-026K |
| Парткод: | 2C927230 |
| Деталь: | SHIELD GASKET F |
| Парткод: | 2BG60250 |
| Деталь: | SHIELD GASKET G |
| Парткод: | 2BG60260 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | DUPLEX UNIT |
| Парткод: | 2BG68153 |
| Деталь: | LEFT GUIDE,MIDDLE TRAY |
| Парткод: | 2AC07160 |
| Деталь: | RACK,SIDE REGISTRATION |
| Парткод: | 68721370 |
| Деталь: | GEAR,SIDE REGISTRATION |
| Парткод: | 66717230 |
| Деталь: | MOUNT,SIDE REGISTRATION DRIVE |
| Парткод: | 68721380 |
| Деталь: | IDLE GEAR 40,TONER SUPPLY |
| Парткод: | 65815060 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | MOUNT,SIDE REGISTRATION MOTOR |
| Парткод: | 68721390 |
| Деталь: | MOTOR,DUPLEX SIDE REGISTRATION |
| Парткод: | 2AC07380 |
| Деталь: | RADIATOR,DUPLEX MOTOR |
| Парткод: | 2AC07370 |
| Деталь: | BINDING BAND SG-130 |
| Парткод: | 49827700 |
| Деталь: | PLATE GUIDE REGIST F |
| Парткод: | 2BG07320 |
| Деталь: | FRONT GUIDE,SIDE REGISTRATION COVER |
| Парткод: | 68721821 |
| Деталь: | SET DU SIDE REGIST F |
| Парткод: | 2BG07240 |
| Деталь: | PLATE GUIDE REGIST R |
| Парткод: | 2BG07330 |
| Деталь: | REAR GUIDE,SIDE REGISTRATION COVER |
| Парткод: | 68721831 |
| Деталь: | SHEET DU SIDE REGIST R |
| Парткод: | 2BG07250 |
| Деталь: | MOUNT DU SW |
| Парткод: | 2BG07370 |
| Деталь: | SWITCH,DUPLEX CONVEYING |
| Парткод: | 68727030 |
| Деталь: | SWITCH,DUPLEX EJECT |
| Парткод: | 68727110 |
| Деталь: | EDGING,EDS-0607U(KITAGAWA) |
| Парткод: | M2104260 |
| Деталь: | WIRE,DU REGISTRATION PI |
| Парткод: | 2BG28580 |
| Деталь: | BINDING BAND,KB-100-1 |
| Парткод: | 49826601 |
| Деталь: | PLATE PROTECT SENSOR |
| Парткод: | 2BG21940 |
| Деталь: | SWITCH,CASSETTE LIFT |
| Парткод: | 66006350 |
| Деталь: | WIRE,DU SIDE PI |
| Парткод: | 2BG28590 |
| Деталь: | PLATE DU M |
| Парткод: | 2BG07350 |
| Деталь: | SOLENOID DU LEADING |
| Парткод: | 2BG07390 |
| Деталь: | LEVER,LEADING REGISTRATION |
| Парткод: | 68721450 |
| Деталь: | STOPPER,LEADING FEED SOLENOID |
| Парткод: | 68721730 |
| Деталь: | MOUNT,LEADING REGISTRATION SOLENOID |
| Парткод: | 68721800 |
| Деталь: | SPRING,LEADING REGISTRATION SOLENOID |
| Парткод: | 68721460 |
| Деталь: | WIRE,DU SIDE MOTOR |
| Парткод: | 2BG28550 |
| Деталь: | WIRE,DUPLEX EJECT PI |
| Парткод: | 2BG28570 |
| Деталь: | STATIC ELIMINATOR,DUPLEX UNIT |
| Парткод: | 67421330 |
| Деталь: | EXIT A ASSY |
| Парткод: | 2BG00442 |
| Деталь: | PLATE EXIT A |
| Парткод: | 2BG21240 |
| Деталь: | SHAFT PULLEY EXIT A |
| Парткод: | 2BG21080 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BG06161 |
| Деталь: | BUSH EXIT ROLLER |
| Парткод: | 2BG07580 |
| Деталь: | SPRING PULLEY EXIT B |
| Парткод: | 2BG21390 |
| Деталь: | HOLDER PULLEY EXIT |
| Парткод: | 2BG21770 |
| Деталь: | PULLEY EXIT FD |
| Парткод: | 2BG21170 |
| Деталь: | SPRING PULLEY FD |
| Парткод: | 2BG21970 |
| Деталь: | ROLLER EXIT A |
| Парткод: | 2BG21010 |
| Деталь: | ROLLER EXIT B |
| Парткод: | 2BG21020 |
| Деталь: | BUSH 6 EW |
| Парткод: | 2BG22970 |
| Деталь: | PULLEY 24,CONVEYING |
| Парткод: | 3A722040 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | BUSH 6 |
| Парткод: | 2BG22960 |
| Деталь: | ACTUATOR EXIT A |
| Парткод: | 2BG21280 |
| Деталь: | PLATE EXIT B |
| Парткод: | 2BG21250 |
| Деталь: | BELT,DRIVE EXIT |
| Парткод: | 2BG21180 |
| Деталь: | DISCHARGER EXIT FD |
| Парткод: | 2BG21580 |
| Деталь: | DISCHARGER EXIT MID |
| Парткод: | 2BG21590 |
| Деталь: | SHEET FD |
| Парткод: | 2BG07591 |
| Деталь: | SWITCH,PHOT0 interruptor |
| Парткод: | 2A127050 |
| Деталь: | ACTUATOR EXIT MI |
| Парткод: | 2BG21930 |
| Деталь: | SCREW M3 CAPTIVE WASHER |
| Парткод: | 2BG02840 |
| Деталь: | DB HV PWB |
| Парткод: | 2BG28261 |
| Деталь: | SPACER,KGPS-10S |
| Парткод: | M2108290 |
| Деталь: | LOCKING WIRE SADDLE,LWS-2NS |
| Парткод: | 49427223 |
| Деталь: | MINIATURE CLAM P, U AMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE,DU SWITCH JUNCTION |
| Парткод: | 2BG27340 |
| Деталь: | WIRE,DB PCB |
| Парткод: | 2BG27170 |
| Деталь: | PLATE MAIN B |
| Парткод: | 2BG26090 |
| Деталь: | BOX CONTROLLER B |
| Парткод: | 2BG26140 |
| Деталь: | BINDING BAND,KB-100-1 |
| Парткод: | 49826601 |
| Деталь: | PLATE SHIELD |
| Парткод: | 2BG26310 |
| Деталь: | CORE 11-25X14 |
| Парткод: | 2A627930 |
| Деталь: | PLATE EARTH CONT BOX |
| Парткод: | 2BG02760 |
| Деталь: | FAN 80X25-120 |
| Парткод: | 2BG27890 |
| Деталь: | EDGING.EDS-1717U |
| Парткод: | M2104220 |
| Деталь: | EDGING, EDS-2323U(KITAGAWA) |
| Парткод: | M2104270 |
| Деталь: | WIRE SADDLE,WS-2WS |
| Парткод: | 49829401 |
| Деталь: | POWER SUPPLY ASSY(100) |
| Парткод: | 2BG01053 |
| Деталь: | POWER SUPPLY ASSY(200) |
| Парткод: | 2BG01063 |
| Деталь: | INLET ASSY A |
| Парткод: | 2BG01230 |
| Деталь: | SHIELD BOX |
| Парткод: | 2BG26020 |
| Деталь: | BRACKET FAN 2 |
| Парткод: | 2BG23070 |
| Деталь: | NOISE FILTER PCB 100 |
| Парткод: | 2FG28121 |
| Деталь: | NOISE FILTER PCB 200 |
| Парткод: | 2FG28131 |
| Деталь: | WIRE,NF |
| Парткод: | 2BG28890 |
| Деталь: | SPACER,KGLS-6RT |
| Парткод: | M2108610 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | 49513902 |
| Деталь: | PLATE N.F PWB |
| Парткод: | 2BG26100 |
| Деталь: | POWER CORD(120) |
| Парткод: | 19527400 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | POWER CODE AS(240) |
| Парткод: | 29927231 |
| Деталь: | FERRITE CORE,SFT-72SN(TAKEUCHI) |
| Парткод: | M70CA010 |
| Деталь: | RECEPTACLE EL 2P.ELR-02V |
| Парткод: | 41529100 |
| Деталь: | PLUG EL 2P.ELP-02V |
| Парткод: | 41529101 |
| Деталь: | CORE SFT-72SNB-026K |
| Парткод: | 2C927230 |
| Деталь: | CORE 15-26X13 |
| Парткод: | 2AV27440 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | OPERATION ASSY E(SP) |
| Парткод: | 2BG68020 |
| Деталь: | SHEET TABLET |
| Парткод: | 2BJ25370 |
| Деталь: | UPPER KEY FUNCTION |
| Парткод: | 2BJ25101 |
| Деталь: | KEY OPERATION 10 |
| Парткод: | 2BJ25020 |
| Деталь: | KEY PRINT E |
| Парткод: | 2BJ25300 |
| Деталь: | KEY STOP |
| Парткод: | 2BJ25040 |
| Деталь: | KEY RESET |
| Парткод: | 2BJ25050 |
| Деталь: | KEY SAVER |
| Парткод: | 2BJ25060 |
| Деталь: | KEY INTERRUPT |
| Парткод: | 2BJ25070 |
| Деталь: | KEY CONTROL |
| Парткод: | 2BJ25080 |
| Деталь: | KEY INIT |
| Парткод: | 2BJ25090 |
| Деталь: | VOLUME OPE UNIT |
| Парткод: | 2BJ25250 |
| Деталь: | BARRIER TABLET |
| Парткод: | 2BJ25240 |
| Деталь: | RIGHT DUST SHIELD |
| Парткод: | 2BJ25230 |
| Деталь: | LEFT DUST SHIELD |
| Парткод: | 2BJ25210 |
| Деталь: | OPERATION UNIT PCB ASSY B |
| Парткод: | 2CX01051 |
| Деталь: | TABLET OPERATION |
| Парткод: | 2FG27150 |
| Деталь: | SPONGE LCD A |
| Парткод: | 2BJ25270 |
| Деталь: | SPONGE LCD B |
| Парткод: | 2BJ25280 |
| Деталь: | LCD PCB |
| Парткод: | 2CJ28080 |
| Деталь: | WIRE LCD |
| Парткод: | 2BJ27140 |
| Деталь: | GROUND PLATE LCD A |
| Парткод: | 2BJ04220 |
| Деталь: | GROUND PLATE LCD C |
| Парткод: | 2BJ04240 |
| Деталь: | CENTER DUST SHIELD |
| Парткод: | 2BJ25220 |
| Деталь: | OPERATION UNIT PCB ASSY A |
| Парткод: | 2CX01100 |
| Деталь: | GROUND PLATE LCD B |
| Парткод: | 2BJ04230 |
| Деталь: | SHIELD LCD |
| Парткод: | 2BJ04210 |
| Деталь: | LEFT LID FAX |
| Парткод: | 2BJ25191 |
| Деталь: | LID OPERATE R,E |
| Парткод: | 2BG25020 |
| Деталь: | EDGING EDS-1 |
| Парткод: | M2104200 |
| Деталь: | WIRE,OPERATION UNIT |
| Парткод: | 2BG27591 |
| Деталь: | KEY FUNCTION R |
| Парткод: | 2BG25030 |
| Деталь: | LEFT KEY COPIER E |
| Парткод: | 2BJ25310 |
| Деталь: | LEFT KEY PRINTER E |
| Парткод: | 2BJ25320 |
| Деталь: | LEFT KEY SCANNER E |
| Парткод: | 2BJ25330 |
| Деталь: | RETAINER LCD |
| Парткод: | 2BJ25390 |
| Деталь: | LEFT LID OPE UNIT |
| Парткод: | 2BJ25151 |
| Деталь: | LEFT LID COPIER |
| Парткод: | 2BJ25161 |
| Деталь: | LEFT LID PRINTER |
| Парткод: | 2BJ25171 |
| Деталь: | LEFT LID SCANNER |
| Парткод: | 2BJ25181 |
| Деталь: | SPACER, KGPS-8RF(KITAGAWA) |
| Парткод: | M2108850 |
| Деталь: | SPACER, KGPS-5RF(KITAGAWA) |
| Парткод: | M2108880 |
| Деталь: | LABEL FUNCTION R |
| Парткод: | 2BG25040 |
| Деталь: | SHEET OPERATION PCB |
| Парткод: | 2CX25010 |
| Деталь: | SHEET FUNCTION |
| Парткод: | 2BJ25260 |
| Деталь: | SHEET LCD A |
| Парткод: | 2BJ25400 |
| Деталь: | SHEET LCD B |
| Парткод: | 2BJ25410 |
| Деталь: | SHEET LCDC |
| Парткод: | 2BJ25420 |
| Деталь: | COVER ISU UP |
| Парткод: | 2BG12010 |
| Деталь: | LEFT KEY FAX E |
| Парткод: | 2BJ25340 |
| Деталь: | COVER OPE UNIT E |
| Парткод: | 2BG25080 |
| Деталь: | PLATE OPERATE M |
| Парткод: | 2BG12070 |
| Деталь: | PLATE OPERATE L |
| Парткод: | 2BG12080 |
| Деталь: | PLATE OPERATE R |
| Парткод: | 2BG12060 |
| Деталь: | SHEET FUNCTION E(SUPPLIED PARTS) |
| Парткод: | 2BG25060 |
| Деталь: | CORE 8-16X10 |
| Парткод: | 3HK27050 |
| Деталь: | CLAMP,LCT-1.5SIEM(TAKEUCHI) |
| Парткод: | M70AF010 |
| Деталь: | FERRITE CORE,SFT-59SN(TAKEUCHI) |
| Парткод: | M70C0010 |
| Деталь: | CLAMP,EMT-4N(TAKEUCHI) |
| Парткод: | M70A5010 |
| Деталь: | CLAMP,EMT-3N(TAKEUCHI) |
| Парткод: | M7005010 |
| Деталь: | PARTS,DK-810 |
| Парткод: | 2BF93112 |
| Деталь: | PARTS,DK-815 |
| Парткод: | 2BG93192 |
| Деталь: | PARTS,MCH UNIT,SP |
| Парткод: | 2BG93210 |
| Деталь: | PLATE DRUM F |
| Парткод: | 2BG08100 |
| Деталь: | JOINT DRIVE DLP |
| Парткод: | 2BG14160 |
| Деталь: | SPRING DS F |
| Парткод: | 2BG14410 |
| Деталь: | SPRING DS R |
| Парткод: | 2BG14420 |
| Деталь: | PARTS,DV-810Y(J/E) |
| Парткод: | 2BG93111 |
| Деталь: | PARTS, DV-810Y(U) |
| Парткод: | 2BG93121 |
| Деталь: | PARTS,DV-810M(J/E) |
| Парткод: | 2BG93131 |
| Деталь: | PARTS,DV-810M(U) |
| Парткод: | 2BG93141 |
| Деталь: | PARTS, DV-810C(J/E) |
| Парткод: | 2BG93151 |
| Деталь: | PARTS,DV-810C(U) |
| Парткод: | 2BG93161 |
| Деталь: | PARTS, DV-810K(J/E) |
| Парткод: | 2BG93170 |
| Деталь: | PARTS,DV-810K(U) |
| Парткод: | 2BG93180 |
| Деталь: | REAR COVER,SCANNER |
| Парткод: | 2A604070 |
| Деталь: | COVER ISU L |
| Парткод: | 2BG12040 |
| Деталь: | COVER ISU R |
| Парткод: | 2BG12030 |
| Деталь: | COVER ISU LOW |
| Парткод: | 2BG12020 |
| Деталь: | SPACER SCANNER |
| Парткод: | 2BG12380 |
| Деталь: | BASE ISU R ASSY |
| Парткод: | 2BG00870 |
| Деталь: | BASE ISU L ASSY |
| Парткод: | 2BG00880 |
| Деталь: | FOOT |
| Парткод: | 2BS03110 |
| Деталь: | PIN,SCANNER POSITIONING |
| Парткод: | 2A612360 |
| Деталь: | STUD SCREW SC |
| Парткод: | 2BG12430 |
| Деталь: | PLATE FOOT |
| Парткод: | 2BG12420 |
| Деталь: | WAVE WASHER WW-5 |
| Парткод: | 2BG12470 |
| Деталь: | LABEL,COVER DUST SHIELD SET(SUPPLIED PARTS) |
| Парткод: | 2CX05020 |
| Деталь: | PIN,SCANNER POSITIONING(SUPPLIED PARTS) |
| Парткод: | 2A612360 |
| Деталь: | DUPLEX UNIT |
| Парткод: | 2BG68153 |
| Деталь: | PLATE GUIDE DU UP |
| Парткод: | 2BG07310 |
| Деталь: | STATIC ELIMINATOR,DUPLEX UNIT |
| Парткод: | 67421330 |
| Деталь: | FRAME DU FRONT |
| Парткод: | 2BG07340 |
| Деталь: | FRAME DU REAR |
| Парткод: | 2BG21690 |
| Деталь: | FRAME DU R |
| Парткод: | 2BG21880 |
| Деталь: | PLATE GUIDE DU R |
| Парткод: | 2BG07300 |
| Деталь: | EDGING, EDS-17L(KITAGAWA) |
| Парткод: | M2104250 |
| Деталь: | EDGING,EDS-2 |
| Парткод: | M2104210 |
| Деталь: | WIRE SADDLE,LWS-1S |
| Парткод: | M2109180 |
| Деталь: | SHAFT DU REFEED |
| Парткод: | 2BG21350 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PULLEY,TURN OVER |
| Парткод: | 68721030 |
| Деталь: | BUSHING 8 |
| Парткод: | 2BC06510 |
| Деталь: | DRIVE GEAR,FIXING SECTION |
| Парткод: | 61522040 |
| Деталь: | ROLLER DU REGIST |
| Парткод: | 2BG21340 |
| Деталь: | ROLLER DU A CONVEY |
| Парткод: | 2BG21320 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | PULLEY Z20 |
| Парткод: | 2BG21360 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | MINIATURE CLAMP,UAMS-07-0 |
| Парткод: | M2105730 |
| Деталь: | STOPPER,TRAILING EDGE TAPPING |
| Парткод: | 2AC07460 |
| Деталь: | GUIDE,TURN OVER FEED SHIFT |
| Парткод: | 2AC07110 |
| Деталь: | SUPPORT PLATE,GUIDE TURN OVER FEED SHIFT |
| Парткод: | 2AC07120 |
| Деталь: | FRAME DU L |
| Парткод: | 2BG21850 |
| Деталь: | LEFT GUIDE,DUPLEX CONVEYING |
| Парткод: | 2AC07232 |
| Деталь: | LOWER ROLLER,DUPLEX REGISTRATION |
| Парткод: | 68721080 |
| Деталь: | PRESSING PLATE,DUPLEX REGISTRATION |
| Парткод: | 68721220 |
| Деталь: | SPRING CIS |
| Парткод: | 78112040 |
| Деталь: | RETAINER,DUPLEX REGISTRATION |
| Парткод: | 68721210 |
| Деталь: | HOOK DU RELEASE |
| Парткод: | 2BG21750 |
| Деталь: | SPRING DU HOOK |
| Парткод: | 2BG21800 |
| Деталь: | PIN,DUPLEX CONVEYING FULCRUM |
| Парткод: | 68721740 |
| Деталь: | STOPPER DU TRAY |
| Парткод: | 2BG21680 |
| Деталь: | LOWER ROLLER B,DUPLEX CONVEYING |
| Парткод: | 2AC07311 |
| Деталь: | BUSHING 6,LOWER REGISTRATION ROLLER |
| Парткод: | 72107160 |
| Деталь: | BUSHING 6,REGISTRATION ROLLER |
| Парткод: | 72107760 |
| Деталь: | LOWER ROLLER,DUPLEX CONVEYING |
| Парткод: | 2AC07210 |
| Деталь: | SPRING PAPER PAD PULLEY |
| Парткод: | 76007150 |
| Деталь: | PRESSING SPRING B,SB |
| Парткод: | 29717220 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | COVER RIGHT F |
| Парткод: | 2BG04050 |
| Деталь: | COVER RIGHT R |
| Парткод: | 2BG04060 |
| Деталь: | COVER REAR |
| Парткод: | 2BG04120 |
| Деталь: | MAGNET CATCH |
| Парткод: | 60804120 |
| Деталь: | COVER INNER LEFT |
| Парткод: | 2BG04150 |
| Деталь: | LEVER LOCK WASTE |
| Парткод: | 2BG04160 |
| Деталь: | SPRING LOCK WASTE |
| Парткод: | 2BG04170 |
| Деталь: | COVER INNER RIGHT |
| Парткод: | 2BG04140 |
| Деталь: | LABEL OPERATION FRONT |
| Парткод: | 2BG05040 |
| Деталь: | FRONT MAGNET,COVER |
| Парткод: | 2BC04530 |
| Деталь: | COVER INNER MIDDLE |
| Парткод: | 2BG04130 |
| Деталь: | LEVER LOCK CONTAINER |
| Парткод: | 2BG09201 |
| Деталь: | SPRING LOCK CONT |
| Парткод: | 2BG09210 |
| Деталь: | STOPPER IMAGE |
| Парткод: | 2BG09220 |
| Деталь: | SWITCH,SIZE |
| Парткод: | 35927420 |
| Деталь: | FRONT COVER ASSY(KM-C2630) |
| Парткод: | 2BG00050 |
| Деталь: | FRONT COVER ASSY D(KM-C2630D) |
| Парткод: | 2BG00730 |
| Деталь: | FUSER 240 ASSY(KM-C2630D) |
| Парткод: | 2BG00400 |
| Деталь: | COVER FRONT (KM-C2630) |
| Парткод: | 2BG04010 |
| Деталь: | COVER FRONT R |
| Парткод: | 2BG04020 |
| Деталь: | BAND A |
| Парткод: | 2BG04310 |
| Деталь: | PLATE MAGCHATCH |
| Парткод: | 2BM04100 |
| Деталь: | COVER CASSETTE R |
| Парткод: | 2BG04100 |
| Деталь: | COVER LEFT |
| Парткод: | 2BG04070 |
| Деталь: | RIGHT COVER ASSY |
| Парткод: | 2BG00100 |
| Деталь: | SHAFT FEED B |
| Парткод: | 2BG06150 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BG06161 |
| Деталь: | COVER FEED R |
| Парткод: | 2BG06200 |
| Деталь: | BAND B |
| Парткод: | 2BG06480 |
| Деталь: | SPRING FEED B |
| Парткод: | 2BG06650 |
| Деталь: | LABEL LEFT COVER A |
| Парткод: | 2BL05250 |
| Деталь: | COVER CASSETTE L |
| Парткод: | 2BG04110 |
| Деталь: | SPRING COVER |
| Парткод: | 2BG04330 |
| Деталь: | PLATE HOLDER IMAGE |
| Парткод: | 2BG09010 |
| Деталь: | WASTE SHUTTER UNIT |
| Парткод: | 2BG68120 |
| Деталь: | OZON FILTER |
| Парткод: | 2BG23030 |
| Деталь: | SHEET FF |
| Парткод: | 2BG02790 |
| Деталь: | CAP TOP FRONT |
| Парткод: | 2BG04360 |
| Деталь: | CAP TOP REAR |
| Парткод: | 2BG04370 |
| Деталь: | SEAL COLOR SYMBOL |
| Парткод: | 2BG05080 |
| Деталь: | HOLDER IMAGE F |
| Парткод: | 2BG09030 |
| Деталь: | PLATE HV DLP B |
| Парткод: | 2BG09060 |
| Деталь: | PLATE EARTH DRUM |
| Парткод: | 2BG09090 |
| Деталь: | PLATE RETAINER IMAGE |
| Парткод: | 2BG09050 |
| Деталь: | LEVER LOCK IMAGE |
| Парткод: | 2BG09250 |
| Деталь: | SCREW C |
| Парткод: | 2BG09260 |
| Деталь: | COVER INNER LOW |
| Парткод: | 2BG09170 |
| Деталь: | LEVER LOCK MCH |
| Парткод: | 2BG09180 |
| Деталь: | SPRING LOCK MCH |
| Парткод: | 2BG09190 |
| Деталь: | SEAL COVER INNER LOW M |
| Парткод: | 2BG09270 |
| Деталь: | SEAL COVER INNER LOW C |
| Парткод: | 2BG09330 |
| Деталь: | SEAL COVER INNER LOW Y |
| Парткод: | 2BG09340 |
| Деталь: | SEAL COVER INNER LOW K |
| Парткод: | 2BG09350 |
| Деталь: | LUTCH |
| Парткод: | 2BM02460 |
| Деталь: | COVER CONTAINER K |
| Парткод: | 2BG09320 |
| Деталь: | COVER CONTAINER Y |
| Парткод: | 2BG09310 |
| Деталь: | COVER CONTAINER C |
| Парткод: | 2BG09300 |
| Деталь: | COVER CONTAINER M |
| Парткод: | 2BG09290 |
| Деталь: | LABEL OPERATION RIGHT |
| Парткод: | 2BG05050 |
| Деталь: | COVER LPH PCB |
| Парткод: | 2BG26050 |
| Деталь: | TOP COVER ASSY G |
| Парткод: | 2BG00740 |
| Деталь: | COVER TOP G |
| Парткод: | 2BG04390 |
| Деталь: | STOPPER PAPER |
| Парткод: | 2BG04300 |
| Деталь: | COVER TOP R |
| Парткод: | 2BG04040 |
| Деталь: | COVER TOP L |
| Парткод: | 2BG04090 |
| Деталь: | FILTER ASSY |
| Парткод: | 2BG00091 |
| Деталь: | COVER DUCT G |
| Парткод: | 2BG04380 |
| Деталь: | COVER FRONT TOP |
| Парткод: | 2BG04080 |
| Деталь: | COVER SW |
| Парткод: | 2BG04520 |
| Деталь: | SHEETSW |
| Парткод: | 2BG04530 |
| Деталь: | TAPE SW |
| Парткод: | 2BG04540 |
| Деталь: | CLUTCH REGIST 32 |
| Парткод: | 2BG22420 |
| Деталь: | PLATE MAIN DRIVE R |
| Парткод: | 2BG22040 |
| Деталь: | SPRING JOINT F |
| Парткод: | 2BG22190 |
| Деталь: | GEAR Z16S-Z40P |
| Парткод: | 2BG22600 |
| Деталь: | BELT CONT DRIVE |
| Парткод: | 2BG22630 |
| Деталь: | GEAR Z46H-Z20P |
| Парткод: | 2BG22590 |
| Деталь: | GEAR Z70H-Z23H |
| Парткод: | 2BG22060 |
| Деталь: | GEAR Z60H |
| Парткод: | 2BG22070 |
| Деталь: | GEAR Z38H |
| Парткод: | 2BG22540 |
| Деталь: | GEAR Z32S CONT |
| Парткод: | 2BG22610 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | COUPLING DLP DRIVE |
| Парткод: | 2BG22520 |
| Деталь: | SPRING COUPLING DLP |
| Парткод: | 2BG22530 |
| Деталь: | SHAFT DLP DRIVE |
| Парткод: | 2BG22050 |
| Деталь: | COLLAR DLP COUPLING |
| Парткод: | 2BG22860 |
| Деталь: | PLATE MAIN DRIVE F |
| Парткод: | 2BG22030 |
| Деталь: | BEARING MF128ZZ |
| Парткод: | 2BG22940 |
| Деталь: | GEAR Z20H |
| Парткод: | 2BG22080 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | BEARING.DRIVE |
| Парткод: | 2AV22410 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | MOTOR,COLOR DEVELOPING |
| Парткод: | 2BG27130 |
| Деталь: | LOCKING WIRE SADDLE,LWS-3NS |
| Парткод: | 49427224 |
| Деталь: | WIRE SADDLE,HL-28-0(KITAGAWA) |
| Парткод: | M2109310 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | HOLDER CONT DRIVE |
| Парткод: | 2BG22830 |
| Деталь: | WORM WHEEL 32-Z20S |
| Парткод: | 2BG22820 |
| Деталь: | GEAR Z28S CONT |
| Парткод: | 2BG22840 |
| Деталь: | JOINT CONT DRIVE |
| Парткод: | 2BG22800 |
| Деталь: | SP JOINT T SW D1234 |
| Парткод: | 2BM14190 |
| Деталь: | GEAR Z28S-Z20S CONT |
| Парткод: | 2BG22810 |
| Деталь: | DC motor |
| Парткод: | 2BM27340 |
| Деталь: | GEAR WORM |
| Парткод: | 2BM14540 |
| Деталь: | WIRE,MOTOR TONER |
| Парткод: | 2BG28690 |
| Деталь: | WIRE SADDLE,WS-2WS |
| Парткод: | 49829401 |
| Деталь: | GEAR Z54S |
| Парткод: | 2BG22350 |
| Деталь: | FEED DRIVE ASSY |
| Парткод: | 2BG00540 |
| Деталь: | PLATE FEED DRIVE R |
| Парткод: | 2BG22260 |
| Деталь: | HOLDER CLUTCH |
| Парткод: | 2BG22280 |
| Деталь: | CLUTCH 1 FEED H |
| Парткод: | 2BG22670 |
| Деталь: | CLUTCH 1 FEED L |
| Парткод: | 2BG22680 |
| Деталь: | SHAFT PICK-UP CL H |
| Парткод: | 2BG22390 |
| Деталь: | SHAFT PICK-UP CL L |
| Парткод: | 2BG22400 |
| Деталь: | BUSH 8 |
| Парткод: | 2BG22980 |
| Деталь: | SHAFT REGIST CLUTCH |
| Парткод: | 2BG22360 |
| Деталь: | SHAFT FEED CLUTCH H |
| Парткод: | 2BG22370 |
| Деталь: | SHAFT FEED CLUTCH L |
| Парткод: | 2BG22380 |
| Деталь: | SHAFT FEED CLUTCH B |
| Парткод: | 2BG22410 |
| Деталь: | GEAR Z111H-Z36S |
| Парткод: | 2BG22290 |
| Деталь: | CLUTCH FEED 34 |
| Парткод: | 2BG22430 |
| Деталь: | CLUTCH FEED L |
| Парткод: | 2BG22660 |
| Деталь: | GEAR 37,S.B |
| Парткод: | 45729402 |
| Деталь: | GEAR Z18S |
| Парткод: | 2BG22310 |
| Деталь: | PLATE FEED UPPER F |
| Парткод: | 2BG22250 |
| Деталь: | GEAR 20 |
| Парткод: | 34922410 |
| Деталь: | MINIATURE CLAMP.UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | CUT WASHER 6 |
| Парткод: | 2BG22930 |
| Деталь: | GEAR Z99H-Z43S |
| Парткод: | 2BG22300 |
| Деталь: | GEAR Z34S-Z31S |
| Парткод: | 2BG22320 |
| Деталь: | GEAR Z43S |
| Парткод: | 2BG22340 |
| Деталь: | GEAR Z34S-Z31S8 |
| Парткод: | 2BG22550 |
| Деталь: | GEAR 21 |
| Парткод: | 3A821110 |
| Деталь: | REAR GEAR 25,DEVELOPING |
| Парткод: | 36714140 |
| Деталь: | CLUTCH DESK FEED L |
| Парткод: | 2BG22690 |
| Деталь: | GEAR B,PF PULLEY |
| Парткод: | 45729404 |
| Деталь: | PLATE FEED LOW F |
| Парткод: | 2BG22270 |
| Деталь: | GEAR Z35S |
| Парткод: | 2BG22330 |
| Деталь: | GEAR,CENTRAL LEAD ROLLER |
| Парткод: | 72622060 |
| Деталь: | GEAR 32,TRANSFER DRIVE |
| Парткод: | 2AZ22490 |
| Деталь: | MOTOR,PAPER FEED |
| Парткод: | 2BG27160 |
| Деталь: | PCB CLUTCH JUNCTION ASSY |
| Парткод: | 2BG01140 |
| Деталь: | EDGING,EDS-0607M(KITAGAWA) |
| Парткод: | M2104350 |
| Деталь: | WIRE,PAPER FEED MOTOR |
| Парткод: | 2BG27210 |
| Деталь: | SPACER,WLS-12-0(KITAGAWA) |
| Парткод: | M2108410 |
| Деталь: | CORE SFT-72SNB-026K |
| Парткод: | 2C927230 |
| Деталь: | FAN (LOW),COOLING |
| Парткод: | 2A627910 |
| Деталь: | SCANNER SUB ASSY |
| Парткод: | 2CX01020 |
| Деталь: | WIRE,HDD POWER SOU RCE(KM-C2630D) |
| Парткод: | 2A660240 |
| Деталь: | WIRE,HDD(KM-C2630D) |
| Парткод: | 2A660230 |
| Деталь: | MOUNT MCS PCB(KM-C2630D) |
| Парткод: | 2A660210 |
| Деталь: | PARTS,UNIT HDD(S P)(KM-C2630D) |
| Парткод: | 2FA93130 |
| Деталь: | CORE 11-25X14 |
| Парткод: | 2A627930 |
| Деталь: | LID,NIC |
| Парткод: | 2A626120 |
| Деталь: | SPACER,FGS-6S(KITAGAWA) |
| Парткод: | M2108790 |
| Деталь: | SPACER,MAIN PCB |
| Парткод: | 2A626300 |
| Деталь: | MCS PCB ASSY(KM-C2630D) |
| Парткод: | 3CV01011 |
| Деталь: | SCANNER MIP ASSY |
| Парткод: | 2BG01040 |
| Деталь: | SCANNER POWER SUPPLY ASSY |
| Парткод: | 2BG01121 |
| Деталь: | PLATE MIP PWB |
| Парткод: | 2BG12130 |
| Деталь: | SCANNER MAIN ASSY(E) |
| Парткод: | 2BG01220 |
| Деталь: | MOUNT PWB |
| Парткод: | 2BG12190 |
| Деталь: | CORE ESD-FPD-40(KM-C2630D) |
| Парткод: | 3CV27040 |
| Деталь: | COVER PWB UP |
| Парткод: | 2BG12300 |
| Деталь: | LID KMAS |
| Парткод: | 2BG12320 |
| Деталь: | BASE SCANNER |
| Парткод: | 2BG12330 |
| Деталь: | PLATE SPRING |
| Парткод: | 2BG12370 |
| Деталь: | GUIDE,CF |
| Парткод: | 2A626110 |
| Деталь: | IC,DIMM MEMORY1(KM-C2630D) |
| Парткод: | 2A727740 |
| Деталь: | WIRE,SCANNER JUNCTION PCB |
| Парткод: | 2BG27720 |
| Деталь: | WIRE,SCANNER MOTOR |
| Парткод: | 2BG27810 |
| Деталь: | WIRE,DP |
| Парткод: | 2BG28810 |
| Деталь: | W1RESCANNER FAN |
| Парткод: | 2BG27690 |
| Деталь: | WIRE SADDLE,WS-2WS |
| Парткод: | 49829401 |
| Деталь: | WIRE SADDLE,WS-2NS |
| Парткод: | 49513902 |
| Деталь: | WIRE,OPERATION UNIT A |
| Парткод: | 2BG27441 |
| Деталь: | WIRE,OPERATION UNIT B |
| Парткод: | 2BG27870 |
| Деталь: | WIRE,SCN POWER S JUNCTION |
| Парткод: | 2BG28520 |
| Деталь: | WIRE,SCN PCB POWER SOURCE |
| Парткод: | 2BG27900 |
| Деталь: | FERRITE CORE,SFT-59SN(TAKEUCHI) |
| Парткод: | M70C0010 |
| Деталь: | PLATE DF CONNECTOR(SUPPLIED PARTS) |
| Парткод: | 2BG12250 |
| Деталь: | COVER CF(SUPPLIED PARTS) |
| Парткод: | 2BG12310 |
| Деталь: | SHIELD GASKET A |
| Парткод: | 2BG28950 |
| Деталь: | CORE 10-20X10 |
| Парткод: | 2A627940 |
| Деталь: | CLAMP,EMT-4N(TAKEUCHI) |
| Парткод: | M70A5010 |
| Деталь: | FEED UNIT ASSY |
| Парткод: | 2BG00633 |
| Деталь: | PLATE MPF |
| Парткод: | 2BG06810 |
| Деталь: | TRAY MPF B |
| Парткод: | 2BG06591 |
| Деталь: | COVER SWITCH |
| Парткод: | 2BG06820 |
| Деталь: | TRAY MPF A |
| Парткод: | 2BG06581 |
| Деталь: | TRAY MPF C |
| Парткод: | 2BG06600 |
| Деталь: | GUIDE PAPER MPF |
| Парткод: | 2BG06210 |
| Деталь: | ACTUATOR CAM MPF |
| Парткод: | 2BM07050 |
| Деталь: | SPRING RETARD MPF |
| Парткод: | 5MMW266LD009 |
| Деталь: | RETARD ROLL MPF ASSY |
| Парткод: | 2BM07400 |
| Деталь: | HOLDER RETARD MPF |
| Парткод: | 2BM07280 |
| Деталь: | RETARD ROLL ASSY |
| Парткод: | 2BM07340 |
| Деталь: | COVER PWB MPF B |
| Парткод: | 2BG06130 |
| Деталь: | PT.SENSOR GP2S30 |
| Парткод: | 5SP24BW52E++040 |
| Деталь: | WIRE,BYPASS UPPER LOWER |
| Парткод: | 2BG27531 |
| Деталь: | LABET TC |
| Парткод: | 2BG05090 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | WIRE,FEED UNIT |
| Парткод: | 2BG27620 |
| Деталь: | BRACKET MPF DRIVE |
| Парткод: | 2BG06680 |
| Деталь: | SOLENOID MPF |
| Парткод: | 2BM27100 |
| Деталь: | GEAR Z28S-Z30S |
| Парткод: | 2BG06760 |
| Деталь: | BRACKET MPF DRAWER |
| Парткод: | 2BG06670 |
| Деталь: | SHAFT ROLL MPF |
| Парткод: | 2BG06090 |
| Деталь: | CLUTCH MPF ASSY |
| Парткод: | 5AAVCLTCH020 |
| Деталь: | CLUTCH 26-B |
| Парткод: | 5EYYAFAAD01++02 |
| Деталь: | BUSH POM B |
| Парткод: | 2BM07320 |
| Деталь: | PLATE LIFT MPF |
| Парткод: | 2BG06520 |
| Деталь: | PAD FRICTION |
| Парткод: | 2BM07170 |
| Деталь: | CURSOR MPF F |
| Парткод: | 2BG06550 |
| Деталь: | CURSOR MPF R |
| Парткод: | 2BG06540 |
| Деталь: | GEAR MANUAL |
| Парткод: | 2B700380 |
| Деталь: | PLATE MPF UP |
| Парткод: | 2BG06530 |
| Деталь: | FRAME MPF |
| Парткод: | 2BG06390 |
| Деталь: | LOCK TRAY MPF |
| Парткод: | 2BG06020 |
| Деталь: | ACTUATOR PAPER MPF |
| Парткод: | 2BM07060 |
| Деталь: | BYPASS PCB ASSY |
| Парткод: | 2BG01151 |
| Деталь: | WIRE,REG SWITCH JUNCTION |
| Парткод: | 2BG27500 |
| Деталь: | SPONGE WIRE D |
| Парткод: | 2BG06570 |
| Деталь: | BUSH METAL |
| Парткод: | 2BM07330 |
| Деталь: | ROLL FEED MPF ASSY |
| Парткод: | 5AAROLL+053 |
| Деталь: | SPRING BOTTOM MPF |
| Парткод: | 2BM07080 |
| Деталь: | COVER PWB MPF A |
| Парткод: | 2BG06120 |
| Деталь: | SWITCH MPF |
| Парткод: | 2BG06830 |
| Деталь: | SPRING GUIDE WIRE |
| Парткод: | 2BG06560 |
| Деталь: | GUIDE WIRE MPF |
| Парткод: | 2BG06850 |
| Деталь: | SPRING SW MPF |
| Парткод: | 2BG06862 |
| Деталь: | SWITCH,PHOT0 interruptor |
| Парткод: | 2A127050 |
| Деталь: | WIRE,BYPASS |
| Парткод: | 2BG27480 |
| Деталь: | SPONGE WIREC |
| Парткод: | 2BG06620 |
| Деталь: | TERMINAL,PAPER SIZE DETECTION |
| Парткод: | 2BC07860 |
| Деталь: | SIZE DETECTION PCB |
| Парткод: | 33928111 |
| Деталь: | SPONGE WIREB |
| Парткод: | 2BG06610 |
| Деталь: | ORIGINAL SIZE SWITCH |
| Парткод: | 76727010 |
| Деталь: | COVER MPF TRAY |
| Парткод: | 2BG06511 |
Коды ошибок
C0030
C0070
C0100
C0110
C0121
C0122
C0123
C0124
C0130
C0140
C0150
C0160
C0170
C0180
C0210
C0240
C0250
C0280
C0310
C0420
C0440
C0500
C0600
C0610
C0630
C0640
C0700
C0710
C0750
C0810
C0820
C0830
C0840
C0860
C0870
C0880
C0890
C0951
C0952
C0953
C0954
C1010
C1100
C1110
C1120
C1130
C1140
C1150
C1160
C1170
C1200
C2101
C2102
C2201
C2202
C2203
C2204
C2500
C2600
C2700
C2710
C3100
C3200
C5100
C5301
C5302
C5303
C5304
C6000
C6020
C6030
C6050
C6100
C6120
C6130
C6150
C6400
C6410
C6420
C7001
C7002
C7003
C7004
C7101
C7102
C7103
C7104
C7200
C7210
C7301
C7302
C7303
C7304
C7420
C7600
C7610
C7620
C7800
C7810
C8010
C8020
C8030
C8040
C8140
C8150
C8170
C8180
C8190
C8210
C8220
C8230
C8240
C8300
C8310
C8320
C8330
C9500
C9510
C9520
C9530 ... C9550
Описание
| Error code: | C0030 |
| Description: | FAX PWB system error |
| Causes: | The FAX processing cannot be continued due to the FAX firmware error. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. |
| Error code: | C0070 |
| Description: | Toner motor |
| Causes: | Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Remedy: | 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0100 |
| Description: | Charge corona winding problem |
| Causes: | An abnormal status is output from the flash memory. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. If not repaired, replace the main PWB. |
| Error code: | C0110 |
| Description: | Backup memory data problem (main PWB) • Data in the specified area of the backup memory does not match the specified values. |
| Causes: | Problem with the backup memory data. Defective main PWB. |
| Remedy: | Problem with the backup memory data. Run maintenance item U021 to set the contents of the backup memory data again. Defective main PWB. If the C0110 is displayed after initializing the backup memory, replace the main PWB and check for correct operation. |
| Error code: | C0121 |
| Description: | EEPROM read error (drum PWB K) • When data is transmitted to the EEPROM on drum PWB K, the ACK signal is not returned within 1 s. |
| Causes: | Poor contact in the connector terminals. Defective drum PWB K. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC9 on the engine controller PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective drum PWB K. Replace the black process unit. |
| Error code: | C0122 |
| Description: | EEPROM read error (drum PWB C) • When data is transmitted to the EEPROM on drum PWB C, the ACK signal is not returned within 1 s. |
| Causes: | Poor contact in the connector terminals. Defective drum PWB C. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC10 on the engine controller PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective drum PWB C. Replace the cyan process unit. |
| Error code: | C0123 |
| Description: | EEPROM read error (drum PWB M) • When data is transmitted to the EEPROM on drum PWB M, the ACK signal is not returned within 1 s. |
| Causes: | Poor contact in the connector terminals. Defective drum PWB M. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine controller PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective drum PWB M. Replace the magenta process unit. |
| Error code: | C0124 |
| Description: | EEPROM read error (drum PWB Y) • When data is transmitted to the EEPROM on drum PWB Y, the ACK signal is not returned within 1 s. |
| Causes: | Poor contact in the connector terminals. Defective drum PWB Y. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC12 on the engine controller PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective drum PWB Y. Replace the yellow process unit. |
| Error code: | C0130 |
| Description: | Backup memory read / write error |
| Causes: | The reading or writing into the flash memory is unavailable. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reconnect the connectors on the main PWB. At that time, fix or replace the wires if they are pinched by other parts or have any damage. When the issue is not resolved, replace the main PWB. |
| Error code: | C0140 |
| Description: | Backup memory (EEPROM) data problem • Reading data from EEPROM is abnormal. |
| Causes: | Data damage of EEPROM. |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | C0150 |
| Description: | Engine EEPROM reading / writing error |
| Causes: | 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing data. 2. The data read reading in 2 points mismatches 8 times continuously. 3. The read data and the write data mismatch 8 times continuously. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0160 |
| Description: | Engine PWB EEPROM data error |
| Causes: | The data read from the EEPROM is judged as abnormal. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing U021 The storage data in the EEPROM on the engine PWB is faulty. Execute U021. Executing U021 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. |
| Error code: | C0170 |
| Description: | Charger count error |
| Causes: | The values in one of the billing counters, life counter or the scanner counter mismatch between the main side and the engine side. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. Detaching and reattaching the main PWB 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0180 |
| Description: | Machine serial number mismatch |
| Causes: | The machine serial Nos. in the main PWB and the EEPROM on the engine PWB mismatch when turning the power on. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. Executing U004 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0210 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and engine CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC1 on the main PWB and YC1 on the engine PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0240 |
| Description: | Printer board* communication problem • The printer board does not respond 120 seconds after the power is turned on. |
| Causes: | Poor contact in the connector terminals. DIMM installed incorrectly. Defective main PWB or printer board. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC9 on the main PWB and YC5 on the printer board, and the continuity across the connector terminals. Repair or replace if necessary. DIMM installed incorrectly. Check the connection. Repair or replace if necessary. Defective main PWB or printer board. Replace the main PWB or printer board and check for correct operation. |
| Error code: | C0250 |
| Description: | Network scanner board* communication problem • The response to the alive command to the network scanner transmitted once to 30 s does not come on the contrary three consecutive times or more. • The response to the communication command transmitted to the network scanner does not return 75 s or more. |
| Causes: | Poor contact in the connector terminals. Defective main PWB or network scanner board. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the main PWB and the connector on the network scanner board, and the continuity across the connector terminals. Repair or replace if necessary. Defective main PWB or network scanner board. Replace the main PWB or network scanner board and check for correct operation. |
| Error code: | C0280 |
| Description: | Communication problem between the fax control PWB and main PWB Communication between the fax control PWB and the main PWB of the machine cannot be performed normally. |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective PWB. Replace the fax control PWB or main PWB and check for correct operation. |
| Error code: | C0310 |
| Description: | HDC communication error • Retry was conducted 50 times after data was sent but there was still no response. |
| Causes: | The engine main PCB or IPU PCB is defective. |
| Remedy: | Replace the engine main PCB or the IPU PCB and check for correct operation. |
| Error code: | C0420 |
| Description: | Side feeder* communication error • A communication error from side feeder is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective side feeder main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC15 on the engine PWB and the connector YC3 on the side feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective side feeder main PWB. Replace the side feeder main PWB. |
| Error code: | C0440 |
| Description: | Document finisher communication problem • A communication error from document finisher is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective finisher main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC14 on the engine PWB and YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective finisher main PWB. Replace the finisher main PWB. |
| Error code: | C0500 |
| Description: | Low fuser temperature |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and YC2 on the deck PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. |
| Error code: | C0600 |
| Description: | Scan problem |
| Causes: | DIMM installed incorrectly. Defective DIMM. |
| Remedy: | Check if the DIMM is inserted into the socket on the scanner main PCB correctly. Replace the DIMM and check for correct operation. |
| Error code: | C0610 |
| Description: | Lens drive problem |
| Causes: | Defective main PWB. |
| Remedy: | Replace the main PWB and check for correct operation. |
| Error code: | C0630 |
| Description: | DMA error |
| Causes: | DMA transmission of the image data does not finish within the certain time. |
| Remedy: | 1 Checking the connection 0 0 2 Checking the connection 0 0 3 Replacing the wire The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • DPCIS - DP relay PWB • DP relay PWB - Main PWB Wiring diagram 4 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. Detaching and reattaching the DP relay PWB 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0640 |
| Description: | Hard Disk error |
| Causes: | The HDD cannot be accessed properly. |
| Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0700 |
| Description: | Side feeder EEPROM error • An error occurs in EEPROM (U4) data read or write for the side feeder main PWB. |
| Causes: | Defective side feeder main PWB. |
| Remedy: | Replace the side feeder main PWB. |
| Error code: | C0710 |
| Description: | Backup memory data problem C • One slave code among three machine number backup data is judged to be broken. |
| Causes: | Broken backup memory. |
| Remedy: | Run maintenance item U004 and enter the correct machine model number. |
| Error code: | C0750 |
| Description: | Document finisher* EEPROM error • A backup memory error is received in serial communication data from the finisher. |
| Causes: | Defective optional document finisher. |
| Remedy: | Replace the document finisher with another unit and check the operation. If the operation is normal, replace or repair the document finisher. |
| Error code: | C0810 |
| Description: | SCC microcomputer status problem • Abnormal SCC microcomputer status has been detected. |
| Causes: | Defective scanner main PCB. |
| Remedy: | Replace the scanner main PCB and check for correct operation. |
| Error code: | C0820 |
| Description: | Fax control PWB CG ROM checksum error (optional fax) A checksum error occurred with the CG ROM data of the fax control PWB. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0830 |
| Description: | FAX PWB flash program area checksum error |
| Causes: | The program stored in the flash memory on the FAX PWB is broken so it cannot perform. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 2 Checking the FAX PWB The FAX PWB is not properly connected. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0840 |
| Description: | RTC error ("Time for maintenance T" appears) |
| Causes: | [Check at start-up] • RTC values are old. • Power has not been turned on for over 5 years. • RTC value is older than 2000/1/1 00:01. [Periodic check per 5 minutes after start-up] • RTC values are older than the ones at the last check. • Partial operation by power reset after C840 error and "Time for Maintenance T" is indicated. |
| Remedy: | 1 Executing U906 The backup battery on the main PWB is faulty, and so, the RTC settings are erased after unplugging the power cord. Execute U906 to reset the display [Maintenance T]. After that, set the date/time (RTC) in the System menu. (It is necessary to execute this process whenever to unplug/plug the power cord.) Executing U906 2 Replacing the main PWB The main PWB is faulty, or the backup battery runs out. If service call error C0840 frequently appears after performing the previous step, replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0860 |
| Description: | Fax control PWB software switch checksum error (optional fax) A checksum error occurred with the software switch value of the fax control PWB. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0870 |
| Description: | PC FAX Image data transmission error |
| Causes: | Data was not properly transmitted even if the specified times of retry were made when the large volume data is transmitted between the FAX PWB and the main PWB. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 3 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 6 Executing U024 The data stored in the SSD is faulty. Execute U024 [SSD Format]. Executing U024 |
| Error code: | C0880 |
| Description: | Program archive problem (optional fax) When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0890 |
| Description: | Fax control PWB CG FONT archive problem (optional fax) When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0951 |
| Description: | 4th drawer lift problem |
| Causes: | Defective EEPROM of LPH drive PWB. |
| Remedy: | Defective EEPROM of LPH drive PWB. Rewrite the correction data. |
| Error code: | C0952 |
| Description: | 4th drawer down problem |
| Causes: | Defective EEPROM of LPH drive PWB. |
| Remedy: | Defective EEPROM of LPH drive PWB. Rewrite the correction data. |
| Error code: | C0953 |
| Description: | 4th drawer lift problem |
| Causes: | Defective EEPROM of LPH drive PWB. |
| Remedy: | Defective EEPROM of LPH drive PWB. Rewrite the correction data. |
| Error code: | C0954 |
| Description: | 4th drawer lift motor |
| Causes: | Defective EEPROM of LPH drive PWB. |
| Remedy: | Defective EEPROM of LPH drive PWB. Rewrite the correction data. |
| Error code: | C1010 |
| Description: | Lift motor 1 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1100 |
| Description: | PF lift motor 1 error |
| Causes: | [The right cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because one of the phenomena below. 1. PF lift sensor 1 does not turn on when passing 23s while PF lift motor 1 turns on for the first time after inserting the cassette. 2. PF lift sensor 1 does not turn on when passing 2s while PF lift motor 1 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 1 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 1 - PF main PWB Wiring diagram 4 Checking PF lift motor 1 PF lift motor 1 is faulty. Replace PF lift motor 1. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift sensor 1 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 1 is not properly attached or faulty. Reattach PF lift sensor 1. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1110 |
| Description: | PF lift motor 2 error |
| Causes: | [The left cassette section of the large capacity feeder for the main unit] The lift error continued 5 times because of one of the phenomena below. 1. PF lift sensor 2 does not turn on when passing 23s while PF lift motor 2 turns on for the first time after inserting the cassette. 2. PF lift sensor 2 does not turn on when passing 2s while PF lift motor 2 turns on for the second time or later after inserting the cassette. 3. The excess lift current protection monitor signal turning on for 1s or more is detected while the PF lift motor 2 is operating. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor 2 - PF main PWB Wiring diagram 4 Replacing PF lift motor 2 PF lift motor 2 is faulty. Replace PF lift motor 2. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •PF lift sensor 2 - PF main PWB Wiring diagram 6 Checking the sensor PF lift sensor 2 is not properly attached or faulty. Reattach PF lift sensor 2. If not repaired, replace the sensor. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1120 |
| Description: | PF left lift position problem (optional 3000-sheet paper feeder) Level switch 1 does not turn on within 30 s of PF lift motor 2 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 1. Defective PF lift motor 2. The PF left lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 1. Check if YC5-4 on the PF main PWB goes low when level switch 1 is turned off. If not, replace PF lift switch 1. Defective PF lift motor 1. Check for continuity across the coil. If none, replace PF lift motor 1. The PF left lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1130 |
| Description: | PF right lift position problem (optional 3000-sheet paper feeder) Level switch 2 does not turn on within 30 s of PF lift motor 1 turning on. |
| Causes: | Poor contact in the connector terminals. Defective level switch 2. Defective PF lift motor 1. The PF right lift does not rise properly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the PF main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective level switch 2. Check if YC5-7 on the PF main PWB goes low when level switch 2 is turned off. If not, replace PF lift switch 2. Defective PF lift motor 2. Check for continuity across the coil. If none, replace PF lift motor 2. The PF right lift does not rise properly. Check the gears and belts, and remedy if necessary. |
| Error code: | C1140 |
| Description: | PF lift motor error Object: Side feeder |
| Causes: | 1. The PF lift upper limit sensor does not turn on when passing 30s after cassette 5 is inserted. 2. The lock-up signal is detected for 200ms continuously during the PF lift motor operation. 3. The PF lift upper limit sensor does not turn on when passing 2s after the upper limit control when printing starts. |
| Remedy: | 1 Checking the bottom plate The bottom plate does not operate properly. Repair or replace the bottom plate when it does not move vertically. 2 Checking the drive gear The drive gear to lift up the bottom plate does not rotate properly. Check if the drive gears to lift up the bottom plate rotate smoothly or have no excessive load. And apply the grease to the frictional parts and fix the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor - PF main PWB Wiring diagram 4 Checking the PF lift motor The PF lift motor is faulty. Replace the PF lift motor. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift upper limit sensor - PF main PWB Wiring diagram 6 Checking the PF lift upper limit sensor The PF lift upper limit sensor is not properly attached or faulty. Reattach the PF lift upper limit sensor. Then, replace it if it is not fixed. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1150 |
| Description: | Side feeder lift motor going down error (optional side feeder) • Lower limit detection switch does not turn off within 15 s of the side feeder lift motor starting (within 200 ms during paper feeding). This error is detected four times successively. |
| Causes: | Poor contact of lower limit detection switch connector terminals. Defective side feeder main PWB. Defective side feeder lift motor. |
| Remedy: | Poor contact of lower limit detection switch connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective side feeder main PWB. Replace the side feeder main PWB. Defective side feeder lift motor. Run maintenance mode U247 and measure the voltage between terminals YC5-A12 (side-feeder main circuit board) and YC6- B11. (Make sure all of LUSSW, UCSSW, LLSSW and RCSSW are off.) Despite either DC24V or DC-24V is observed but if the side-feeder lift motor does not operate, replace the side-feeder lift motor. |
| Error code: | C1160 |
| Description: | Paper feeder lift motor error (upper 500-sheet paper feeder) • The paper feeder limit detection sensor is not turned on within 10,000 ms after the cassette is inserted and the sensor is not turned on within 500 ms at the second time and after. |
| Causes: | Defective bottom plate elevation mechanism. Defective paper feeder lift motor. Defective engine controller PWB. |
| Remedy: | Defective bottom plate elevation mechanism. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective paper feeder lift motor. Replace the paper feeder lift motor. Defective engine controller PWB. Replace the engine controller PWB. |
| Error code: | C1170 |
| Description: | Paper feeder lift motor error (lower 500-sheet paper feeder) • The paper feeder limit detection sensor is not turned on within 10,000 ms after the cassette is inserted and the sensor is not turned on within 500 ms at the second time and after. |
| Causes: | Defective bottom plate elevation mechanism. Defective paper feeder lift motor. Defective engine controller PWB. |
| Remedy: | Defective bottom plate elevation mechanism. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective paper feeder lift motor. Replace the paper feeder lift motor. Defective engine controller PWB. Replace the engine controller PWB. |
| Error code: | C1200 |
| Description: | Duplex side registration motor error • The duplex side registration home position sensor does not detect the home position of the side registration guide. |
| Causes: | Defective duplex side registration home position sensor. Defective duplex side registration motor. Defective duplex PWB. |
| Remedy: | Defective duplex side registration home position sensor. Check the connection of connector YC29 on the engine PWB and the connector YC1 on the duplex PWB. Repair or replace if necessary. Defective duplex side registration motor. Replace the duplex side registration motor. Defective duplex PWB. Replace the duplex PWB. |
| Error code: | C2101 |
| Description: | Developer motor error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking the developer motor The developer motor drive is faulty. Execute U030 [DLP(K)] and check the developer motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 5 Checking the developer motor The developer motor is not properly attached or faulty. Reattach the developer motor. If not repaired, replace the motor. Detaching and reattaching the developer motor 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2102 |
| Description: | Developer motor C error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor C drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor C is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking developer motor C The developer motor C drive is faulty. Execute U030 [DLP(C)] and check the developer motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 5 Checking developer motor C Developer motor C is not properly attached or faulty. Reattach developer motor C. If not repaired, replace the motor. Detaching and reattaching the main drive unit 6 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2201 |
| Description: | Drum motor steady-state error |
| Causes: | The ready signal is at the H level for 1s continuously after the drum motor became stable. |
| Remedy: | 1 Checking the drum motor The drum motor drive is faulty. Execute U030 [Process] and check the drum motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 4 Checking the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2202 |
| Description: | Drum motor C steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB C at every 1s. |
| Remedy: | 1 Checking drum motor C The drum motor C drive is faulty. Execute U030 [Process] and check the drum motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor C Drum motor C is faulty. Replace drum motor C. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2203 |
| Description: | Drum motor M steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB M at every 1s. |
| Remedy: | 1 Checking drum motor M The drum motor M drive is faulty. Execute U030 [Process] and check the drum motor M operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor M - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor M Drum motor M is faulty. Replace drum motor M. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2204 |
| Description: | Drum motor Y steady-state error |
| Causes: | The steady-state speed error or the abnormal motor drive is detected when reading the signal from encoder PWB Y at every 1s. |
| Remedy: | 1 Checking drum motor Y The drum motor Y drive is faulty. Execute U030 [Process] and check the drum motor Y operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor Y - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 3 Replacing drum motor Y Drum motor Y is faulty. Replace drum motor Y. 4 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 5 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2500 |
| Description: | Feed motor error |
| Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
| Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
| Error code: | C2600 |
| Description: | PF feed motor error |
| Causes: | The ready signal is not at the L level (stable rotation) after passing 1s since the PF feed motor drive started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected, or it is faulty. Execute U247 [2PF] or [LCF] > [Motor On] to check the paper feed operation. If the PF feed motor does not operate properly, reconnect the connector of the motor. Check if the PF feed roller and the drive gears rotate smoothly and have no excessive load, apply the grease (EM-50LP, Part no.: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF PWB • PF PWB - Engine PWB (Drawer connector between the paper feeder and the main unit) Service Manual - Section 8 `PWBs` 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF Drive Unit 4 Firmware upgrade The engine firmware or the PF firmware is faulty. Upgrade the engine firmware and the PF firmware to the latest version. Firmware Update 5 Replacing the PF PWB The PF PWB is faulty. Replace the PF PWB. Detaching and reattaching the PF PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C2700 |
| Description: | Color release motor error |
| Causes: | Turning the color release sensor on and off is not detected for 5s while the color release motor is driving. |
| Remedy: | 1 Checking the drive components The drive transmission from the color release motor error is faulty. Execute U030 [CMY Release]. If the drive from the motor is not transmitted, repair the drive parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 5 Primary transfer belt unit replacement The primary transfer roller lift-up drive section is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2710 |
| Description: | Waste toner box motor error • After the motor drive remote signal is turned on, the overcurrent detection signal is detected continuously for more than 200 ms. |
| Causes: | Overload on the waste toner box motor. Defective waster toner box motor. |
| Remedy: | Overload on the waste toner box motor. Check to see if the waste toner in the waste toner box is solidified. If any problem is found, replace the waste toner box. Defective waster toner box motor. Replace the waster toner box motor. |
| Error code: | C3100 |
| Description: | Carriage error |
| Causes: | When turning the power on or finishing originals scan through the scanner, the alignment of the home position sensor (turning on / off the sensor) fails and the error is detected. Then, the error is detected twice continuously even the initial operation is executed. |
| Remedy: | 1 Unlocking the scanner mirror frame The scanner mirror frame is not unlocked. Unlock the scanner mirror frame (lamp unit assy). Unlocking the scanner mirror frame 2 Checking the scanner movement A load is applied to the scanner movement. Check the operation of the lamp by U073 or manually moving it. If there is an excess load, check if there are any foreign objects on the optical wire or optical wire drum and clean it. After that, apply grease on the scanner rail. Detaching and reattaching the scanner wires 3 Checking the scanner wires The scanner wires are dirty or come off. Clean and reattach the scanner wires. Detaching and reattaching the scanner wires 4 Checking the scanner motor The scanner motor is faulty. Reattach the scanner motor and reconnect the connector. If not repaired, replace it. 5 Checking the belt tension of the scanner motor A load is applied to the scanner movement since the belt tension is improper. Adjust the scanner motor belt tension properly. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Scanner motor - Engine PWB Wiring diagram 7 Checking the home position sensor The home position sensor is not properly attached. Reattach the home position sensor. 8 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Home position sensor - Engine PWB Wiring diagram 9 Replacing the home position sensor The home position sensor is faulty. Replace the home position sensor. 10 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3200 |
| Description: | LED lamp startup error |
| Causes: | The white reference data acquired by lighting the LED lamp at the initial operation does not reach the specified value. Or, the light amount detected by the CCD PWB is not enough. (2 or more LED lamps do not light. The light does not reach the CCD PWB due to condensation.) |
| Remedy: | 1 Checking the LED lamp The LED lamp does not light. Execute U061 [CCD] and check if the LED lamp is lit. If not, replace the lamp unit. After that, execute U411 [Table(ChartA)]. Detaching and reattaching the lamp unit 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB • LED PWB - CCD PWB Wiring diagram 3 Checking the mirror The mirror or lens is frosted due to condensation. Clean the mirrors. If the condensation at the scanner section is resolved naturally by opening the document processor or the platen cover, turn the power switch off and on. 4 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5100 |
| Description: | Main high-voltage error • While the main high-voltage output remote signal is on, an alarm signal is detected continuously for 400 ms. |
| Causes: | Defective high voltage PWB. Leak of main high-voltage. Poor contact in connector terminals. |
| Remedy: | Defective high voltage PWB. Replace the high voltage PWB and check for correct operation. Leak of main highvoltage. Check the main charger unit and replace if necessary. Poor contact in connector terminals. Check the connection of connector YC7 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. |
| Error code: | C5301 |
| Description: | Cleaning lamp K error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp K. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the main front PWB and the connector of the drum unit K, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp K. Replace the drum unit K. Defective PWB. Replace the main front PWB or engine PWB and check for correct operation. |
| Error code: | C5302 |
| Description: | Cleaning lamp C error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp C. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC5 on the sub front PWB and the connector of the drum unit C, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp C. Replace the drum unit C. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C5303 |
| Description: | Cleaning lamp M error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp M. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC7 on the sub front PWB and the connector of the drum unit M, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp M. Replace the drum unit M. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C5304 |
| Description: | Cleaning lamp Y error |
| Causes: | Poor contact in the connector terminals. Defective cleaning lamp Y. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the sub front PWB and the connector of the drum unit Y, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp Y. Replace the drum unit Y. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation. |
| Error code: | C6000 |
| Description: | IH heating error 1 |
| Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6020 |
| Description: | Fuser center thermistor high temperature error |
| Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6030 |
| Description: | Fuser center thermistor broken |
| Causes: | The output from the fuser center thermistor is under 20°C / 68°F level during warm-up. Or, the temperature detected at the fuser center thermistor does not change for 10s after turning the fuser heater on. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6050 |
| Description: | Fuser center thermistor low temperature error |
| Causes: | The fuser center thermistor detects less than 100°C / 212°F for 1s after warm-up, or during print or standby. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 11 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit |
| Error code: | C6100 |
| Description: | Fuser heater broken (For the internal count) |
| Causes: | The fuser press thermistor temperature detected does not reach the control temperature within 480s after shifting to the low power mode. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6120 |
| Description: | Fuser press thermistor high temperature error |
| Causes: | The fuser press thermistor detects 210°C / 410°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6130 |
| Description: | Fuser press thermistor broken |
| Causes: | The detection temperature of the fuser press thermistor does not reach 30°C / 86°F within 60s since warm-up starts. |
| Remedy: | 1 Removing foreign material There are foreign objects between the fuser press thermistor and the press roller. Or, the foreign objects are adhered on the press roller. Remove foreign objects if any on the press roller. Then, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6150 |
| Description: | Fuser press thermistor low temperature error |
| Causes: | The fuser press thermistor detects less than 30°C / 86°F for 1s after warm-up. |
| Remedy: | 1 Removing foreign material There are foreign objects between the fuser press thermistor and the press roller. Or, the foreign objects are adhered on the press roller. Remove foreign objects if any on the press roller. Then, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 9 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB 10 Replacing the IH unit The IH unit is faulty. Replace the IH unit. |
| Error code: | C6400 |
| Description: | Zero-cross signal error • The engine PWB does not detect the zero-crossing signal (Z CROSS SIG) for 5 s. |
| Causes: | Poor contact in the connector terminals. Defective DC power source PWB. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and YC6 on the DC power source PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective DC power source PWB. Check if the zero-crossing signal is output from YC6-3 on the DC power source PWB. If not, replace the DC power source PCB. Defective engine PWB. Replace the engine PWB if C6400 is detected while YC6-3 on the DC power source PWB outputs the zero-crossing signal. |
| Error code: | C6410 |
| Description: | Fuser unit type mismatch error |
| Causes: | "Unit Identification" code in the EEPROM of the fuser unit does not match the main unit. The fuser unit for other model is installed. |
| Remedy: | 1 Replacing the fuser unit The fuser unit for other models is installed. Install the fuser unit for the applicable models. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB Wiring diagram 5 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6420 |
| Description: | Fuser unit fuse cut problem The fuse cannot be cut, When replacing the fuser unit, the fuse cannot be cut in 3 s after the fuse cut signal is turned on. |
| Causes: | Poor contact in the connector terminals. Fuser unit connector inserted incorrectly. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC1 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. |
| Error code: | C7001 |
| Description: | Toner motor error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Toner motor - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7002 |
| Description: | Toner motor C error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor C - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7003 |
| Description: | Toner motor M error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor M - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7004 |
| Description: | Toner motor Y error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor Y - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7101 |
| Description: | Toner sensor error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The drive gears for the developer unit are damaged. (The spiral cannot rotate.) Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7102 |
| Description: | Toner sensor C error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7103 |
| Description: | Toner sensor M error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7104 |
| Description: | Toner sensor Y error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7200 |
| Description: | Internal thermistor broken (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) exceeds the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7210 |
| Description: | Internal thermistor short-circuited (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) is less than the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7301 |
| Description: | Toner hopper motor error |
| Causes: | It occurs 15 times continuously that the screw sensor does not detect the pulse for 200ms when driving the toner hopper motor. |
| Remedy: | 1 Checking the toner hopper motor The toner hopper motor is faulty. Execute U135 [Hopper] and check the toner hopper motor operation. (Go to the next step.) Executing U135 2 Checking the toner hopper drive section The toner hopper screw does not properly rotate due to excessive load. (The pulse plate does not rotate.) Rotate the toner hopper screw manually. Then, check if toner is not clogged in the toner hopper, and clean inside the toner hopper if necessary. Detaching and reattaching the inner unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner hopper motor - Front PWB• Screw sensor - Front PWB?• Front PWB - Engine PWB 4 Checking the screw sensor The screw sensor is faulty. Reattach the screw sensor. If not repaired, replace the sensor. 5 Replacing the drive parts The drive transmission from the toner hopper motor is faulty. Reattach the drive gears or the toner hopper motor. If not repaired, replace the parts faulty in operation. Or, replace the inner unit. Detaching and reattaching the inner unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7302 |
| Description: | Toner hopper motor C error |
| Causes: | Screw sensor C can not detect the pulse for 200ms 15 times continuously when the toner hopper motor C drives. |
| Remedy: | 1 Checking the toner hopper motor The toner hopper motor is faulty. Execute U135 [Hopper] and check the toner hopper motor operation. (Go to the next step.) Executing U135 2 Checking the toner hopper drive section The toner hopper screw does not properly rotate due to excessive load. (The pulse plate does not rotate.) Rotate the toner hopper screw manually. Then, check if toner is not clogged in the toner hopper, and clean inside the toner hopper if necessary. Detaching and reattaching the inner unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner hopper motor C - Retainer PWB • Retainer PWB - Front PWB?• Screw sensor C - Front PWB?• Front PWB - Engine PWB Wiring diagram 4 Checking the screw sensor The screw sensor is faulty. Reattach screw sensor C. If not repaired, replace the sensor. 5 Replacing the drive parts The drive transmission from the toner hopper motor is faulty. Reattach the drive gears or toner hopper motor C. If not repaired, replace the parts faulty in operation. Or, replace the inner unit. Detaching and reattaching the inner unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7303 |
| Description: | Toner hopper motor M error |
| Causes: | Screw sensor M can not detect the pulse for 200ms 15 times continuously when the toner hopper motor C drives. |
| Remedy: | 1 Checking the toner hopper motor The toner hopper motor is faulty. Execute U135 [Hopper] and check the toner hopper motor operation. (Go to the next step.) Executing U135 2 Checking the toner hopper drive section The toner hopper screw does not properly rotate due to excessive load. (The pulse plate does not rotate.) Rotate the toner hopper screw manually. Then, check if toner is not clogged in the toner hopper, and clean inside the toner hopper if necessary. Detaching and reattaching the inner unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner hopper motor M - Retainer PWB • Retainer PWB - Front PWB?• Screw sensor M - Front PWB?• Front PWB - Engine PWB Wiring diagram 4 Checking the screw sensor The screw sensor is faulty. Reattach screw sensor M. If not repaired, replace the sensor. 5 Replacing the drive parts The drive transmission from the toner hopper motor is faulty. Reattach the drive gears or toner hopper motor M. If not repaired, replace the parts faulty in operation. Or, replace the inner unit. Detaching and reattaching the inner unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7304 |
| Description: | Toner hopper motor Y error |
| Causes: | Screw sensor Y can not detect the pulse for 200ms 15 times continuously when the toner hopper motor C drives. |
| Remedy: | 1 Checking the toner hopper motor The toner hopper motor is faulty. Execute U135 [Hopper] and check the toner hopper motor operation. (Go to the next step.) Executing U135 2 Checking the toner hopper drive section The toner hopper screw does not properly rotate due to excessive load. (The pulse plate does not rotate.) Rotate the toner hopper screw manually. Then, check if toner is not clogged in the toner hopper, and clean inside the toner hopper if necessary. Detaching and reattaching the inner unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • insert the connectors. Replace the wire when it has no continuity.• Toner hopper motor Y - Retainer PWB • Retainer PWB - Front PWB?• Screw sensor Y - Front PWB?• Front PWB - Engine PWB 4 Checking the screw sensor The screw sensor is faulty. Reattach screw sensor Y. If not repaired, replace the sensor. 5 Replacing the drive parts The drive transmission from the toner hopper motor is faulty. Reattach the drive gears or toner hopper motor Y. If not repaired, replace the parts faulty in operation. Or, replace the inner unit. Detaching and reattaching the inner unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7420 |
| Description: | Uninstalled primary transfer unit |
| Causes: | 1. Unit identification code does not match. 2. Unit for the other model is installed. |
| Remedy: | 1 Replacing the primary transfer unit The primary transfer unit for other models is installed. Install the primary transfer unit for the applicable models. Detaching and reattaching the Primary Transfer Unit 2 Reinstalling the primary transfer unit The connector of the primary transfer unit is not firmly connected. Reinstall the primary transfer unit so that the connector firmly connects. Detaching and reattaching the Primary Transfer Unit 3 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Transfer connect PWB - Feed image PWB Service Manual - Section 8 `PWBs` 4 Firmware upgrade The firmware is faulty. Reinstall the engine firmware. Firmware Update 5 Replacing the transfer connection PWB The transfer connection PWB is faulty. Replace the transfer connection PWB. 6 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. |
| Error code: | C7600 |
| Description: | Image density sensor detection error • The measured value at the end of color compensation is 255 or more for no image and LED off or the measured value for no image and LED on exceeds the value for any image. |
| Causes: | Defective engine controller PCB. Defective imege density sensor. |
| Remedy: | Replace the primary transfer unit. Check to see if the image density sensor is properly connected. |
| Error code: | C7610 |
| Description: | Image density sensor detection error • The measurement result of each density batch at the end of color compensation shows abnormal relation of density in size. |
| Causes: | Defective engine controller PCB. Defective imege density sensor. |
| Remedy: | Check the drum unit, high voltage unit, developing unit, and transfer unit. If any problem is found, replace the unit. |
| Error code: | C7620 |
| Description: | Automatic color registration error |
| Causes: | 1. The patch print position on the primary transfer belt is not within the readable area by the ID sensor. 2. The primary transfer belt surface is dirty, or the patch print density is too light. |
| Remedy: | 1 Resetting the main power The ID sensor does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing Calibration The last calibration failed. Execute U464 [Calib]. Maintenanc e Mode List 3 (In case if the printout is light) Checking the developer unit (35ppm or faster models) The developing roller does not contact with the drum. Switch the lock lever up and down and return the developer roller to the setting position. If the developer roller does not return due to the breakage of the lock lever or the failure of the developer roller pressure wire, replace the developer unit. Detaching and reattaching the Developer Unit 4 (In case if the printout is light) Checking the connecting gear of the front cover for the maintenance (25/32PPM models) The developer roller does not contact the drum since it does not properly interlock with the opening and closing operation of the front cover for the maintenance. If the developer roller does not contact the drum even if closing the front cover for the maintenance, reattach the gear connecting to the front cover for the maintenance. 5 (In case if the printout is light) Cleaning / replacing the LSU. The laser does not output properly from the LSU. Or, LSU dustproof glass is dirty. Clean the LSU. If not repaired, replace it. Detaching and reattaching the LSU 6 (In case if the printout is light) Improving the condensation of the drum surface (35ppm or faster models) Condensation on the drum surface Execute the drum refresh. And next, set [On] at U339 [Drum heater] to turn on the drum heater. Adjust/ Maintenanc e Menu (Operation Guide - Section 10) Maintenanc e Mode List 7 Cleaning the ID sensor The ID sensor is dirty. Clean the surface of the front and rear ID sensors. 8 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not operate properly, reattach the cleaning solenoid. Maintenanc e Mode List 9 Checking the primary transfer unit The primary transfer belt surface is dirty. Clean the surface of the primary transfer belt, or replace the primary transfer unit. Detaching and reattaching the Primary Transfer Unit 10 (When the image is too light) Checking the main high voltage PWB / transfer high voltage PWB Proper current does not flow as the main high voltage PWB or the contact point of the transfer high voltage PWB is faulty. Reattach the main high voltage PWB and the transfer high voltage PWB. 11 (When the color registration occurs) Checking the LSU / drum unit LSU or drum unit is not installed correct position. Or, LSU is faulty. If the color registration occurs, reinstall the LSU and the drum unit at the proper position. If not repaired, replace the LSU. Detaching and reattaching the Drum Unit Detaching and reattaching the LSU 12 Checking the ID sensor The ID sensor is not properly attached, or the connector is not properly connected. Reattach the front and rear ID sensors and reconnect the connectors. 13 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. Firmware Update 14 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front ID sensor and Rear ID sensor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 15 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 16 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7800 |
| Description: | Outer thermistor broken (For the internal count) |
| Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7810 |
| Description: | Short-circuited external thermistor • The thermistor input value is 0.5 V or less. |
| Causes: | Poor contact in the connector terminals. Defective humidity sensor. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC13 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective humidity sensor. Replace the humidity sensor. Defective engine PWB. Replace the engine PWB. |
| Error code: | C8010 |
| Description: | Punch motor error 1 Object: 4000-sheet finisher + Punch unit |
| Causes: | 1. The punch home position sensor does not turn on when passing 200ms after driving the punch motor. 2. The pulse plate does not count the specified pulse when passing 300ms after the punch operation starts. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • Punch home position sensor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. 5 Checking the punch home position sensor The punch home position sensor is not properly attached or faulty. Execute U241 [Punch] > [Punch HP]. If the PH home position sensor does not properly operate, reattach it. If not repaired, replace the sensor. Executing U241 6 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 7 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8020 |
| Description: | Punch motor error 2 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position is not aligned within 3s when initializing the home position or standby. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8030 |
| Description: | Punch motor error 3 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position detection does not turn off within 50ms when initializing the home position. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8040 |
| Description: | Document finisher lower paper conveying belt problem • During initialization, the intermediate tray lower sliding plate is not detected in the home position within 3 s after the belt returns to the home position. JAM87 is indicated the first time this problem occurs. If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the lower paper conveying belt. • When the intermediate tray lower sliding plate is operated from the home position, the lower paper conveying belt home position sensor does not turn off within 1 s. |
| Causes: | Phase shift of the lower paper conveying belt. Malfunction of the lower paper conveying belt motor. Malfunction of the lower paper conveying belt home position sensor. Loose connection of the lower paper conveying belt home position sensor connector. Incorrect insertion of the intermediate tray. Defective finisher main PWB. |
| Remedy: | Phase shift of the lower paper conveying belt. Correct the phase of the lower paper conveying belt and check for correct operation. Malfunction of the lower paper conveying belt motor. Replace the lower paper conveying belt motor and check for correct operation. Malfunction of the lower paper conveying belt home position sensor. Replace the lower paper conveying belt home position sensor and check for correct operation. Loose connection of the lower paper conveying belt home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Incorrect insertion of the intermediate tray. Check whether the intermediate tray catches are damaged. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8140 |
| Description: | Main tray error 1 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8150 |
| Description: | Main tray error 2 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 do not turn on and off when passing 5s when the main tray descends. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8170 |
| Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
| Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
| Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8180 |
| Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
| Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
| Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8190 |
| Description: | DF side registration motor 2 error 1 Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while executing the operation of returning to the home position. |
| Remedy: | 1 Checking the rear DF side registration guide The rear DF side registration guide is not assembled properly. If the rear DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear DF side registration guide drive components The rear DF side registration guide drive parts are not properly attached or faulty. Reattach the rear DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 2 - DF main PWB • DF side registration sensor 2 - DF main PWB 4 Replacing DF side registration motor 2 DF side registration motor 2 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking DF side registration sensor 2 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8210 |
| Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8220 |
| Description: | Document finisher* front clincher problem • During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position. JAM90 is indicated the first time this problem occurs. If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher. • When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms. |
| Causes: | Loose connection of the front clincher motor connector. Malfunction of the front clincher motor. Malfunction of the front clincher home position sensor. Loose connection of the front clincher home position sensor connector. Defective finisher main PWB. |
| Remedy: | Loose connection of the front clincher motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Malfunction of the front clincher motor. Replace the front clincher motor and check for correct operation. Malfunction of the front clincher home position sensor. Replace the front clincher home position sensor and check for correct operation. Loose connection of the front clincher home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8230 |
| Description: | DF staple motor error Object: 4000-sheet finisher |
| Causes: | J7000 (DF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple cannot operate manually without paper jam, repair the part that restricts the DF staple. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple unit - DF main PWB Wiring diagram 3 Replacing the DF staple unit The DF staple unit is faulty. Replace the DF staple unit. Detaching and reattaching the DF staple unit 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8240 |
| Description: | Document finisher rear clincher problem • During initialization, the rear clincher is not detected in the home position within 500 ms after the rear clincher returns to the home position. JAM90 is indicated the first time this problem occurs. If the problem occurs after initialization when the front cover is opened and closed, the problem is in the rear clincher. • When the rear clincher is operated from the home position, the rear clincher home position sensor does not turn off within 500 ms. |
| Causes: | Loose connection of the rear clincher motor connector. Malfunction of the rear clincher motor. Malfunction of the rear clincher home position sensor. Loose connection of the rear clincher home position sensor connector. Defective finisher main PWB. |
| Remedy: | Loose connection of the rear clincher motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Malfunction of the rear clincher motor. Replace the rear clincher motor and check for correct operation. Malfunction of the rear clincher home position sensor. Replace the rear clincher home position sensor and check for correct operation. Loose connection of the rear clincher home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8300 |
| Description: | Main program error / Folding unit communication error Object: 4000-sheet finisher + Folding unit |
| Causes: | The main program of the folding unit is faulty when turning the power on. The communication error appears 10 times continuously after finishing the folding unit firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the BF firmware and the DF firmware to the latest version. Firmware Update 3 Checking the BF set switch The BF set switch is not properly attached. Reattach the BF set switch. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 5 Replacing the BF set switch The BF set switch is faulty. Execute U241 [Booklet] > [Set]. If the BF set switch does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8310 |
| Description: | BF side registration motor 2 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 2 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the upper BF side registration guide The upper BF side registration guide is not assembled properly. If the upper BF side registration guide is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the upper BF side registration guide drive components The upper BF side registration guide drive parts are not properly attached or faulty. Reattach the upper BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 2 - BF main PWB • BF side registration sensor 2 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 2 BF side registration motor 2 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 2 BF side registration sensor 2 is not properly attached or faulty. Reattach BF side registration sensor 2 and execute U241 [Booklet] > [Width Down HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8320 |
| Description: | BF adjustment motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | At the initialization, turning on of the BF adjustment sensor is not detected after 2.5s passes. |
| Remedy: | 1 Checking the BF shift belt The BF shift belt is not assembled properly. If the BF shift belt is not operated manually, repair the part that restricts the operation. 2 Checking the BF shift belt drive components The BF shift belt drive parts are not properly attached or faulty. Reattach the BF shift belt drive parts. Reattach it if the belt comes off. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF adjustment motor 1, 2 - BF main PWB • BF adjustment sensor 1, 2 - BF main PWB Wiring diagram 4 Replacing BF adjustment motor 1, 2 BF adjustment motor 1 or 2 is faulty. Execute U240 [Booklet] > [Bundle Down] or [Bundle Up]. If BF adjustment motor 1 or 2 does not properly operate, replace them. Executing U240 5 Checking BF adjustment sensor 1, 2 BF adjustment sensor 1 or 2 is not properly attached or faulty. Reattach BF adjustment sensor 1 or 2 and execute U241 [Booklet] > [Width Down HP] or [Bundle Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8330 |
| Description: | BF blade motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The BF blade sensor does not turn on after passing 3s during the initial operation. |
| Remedy: | 1 Checking the BF blade The BF blade is not assembled properly. If the BF blade is not operated manually, repair the part that restricts the operation. 2 Checking the BF blade drive components The BF blade drive parts are not properly attached or faulty. Reattach the BF blade drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF blade motor - BF main PWB • BF blade sensor - BF main PWB Wiring diagram 4 Replacing the BF blade motor The BF blade motor is faulty. Execute U240 [Booklet] > [Blade]. If the BF blade motor does not properly operate, replace it. Executing U240 5 Checking the BF blade sensor The BF blade sensor is faulty. Reattach the BF blade sensor and reinsert the connector. Next, execute U241 [Booklet] > [Blade HP]. If it does not properly operate, replace the sensor. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C9500 |
| Description: | Image processing circuit error (Scanner) |
| Remedy: | 1 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • Engine PWB - Main PWB Wiring diagram 2 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C9510 |
| Description: | Image processing circuit error (DP) |
| Remedy: | 1 Checking the DP relay PWB The DP relay PWB is not properly attached. Reattach the DP relay PWB. 2 Checking the connection The connector is not properly connected. Or, the SATA cable is faulty. 0 Wiring diagram 3 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. 4 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C9520 |
| Description: | Scanner sub PCB problem |
| Causes: | Scanner sub PCB problem |
| Remedy: | Check the connection of the connector of the scanner sub PCB. Replace the scanner sub PCB or the scanner main PCB one by one. |
| Error code: | C9530 ... C9550 |
| Description: | Contact the Service Administrative Division. |
| Remedy: | Contact the Service Administrative Division. |
