Kyocera KM-C830
Рейтинг
Модули
FACE DOWN UNIT II
FEED UNIT
COVERS
DEVELOPER D1 UNIT
FRAME UNIT I
Controller Box
Drive Unit II
OPTION I (Original Tray)
FUSER UNIT
Drum Unit
FRAME UNIT II
FRAME PROCESS UNIT
FEED UNIT II
OPTION II
Drive Unit I
DEVELOPER D4 UNIT
Fuser Unit II
PRIMARY TRANSFER II
DEVELOPER D2 UNIT
PRIMARY TRANSFER
BYPASS TRAY2
DEVELOPER D3 UNIT
SCANNER UNIT
ELECTRICAL PARTS I
ELECTRICAL PARTS II
ELECTRICAL PARTS III
Face Down Unit
Детали ELECTRICAL PARTS I
| Деталь: | SHAFT ROLLER FU |
| Парткод: | 2BM21520 |
| Деталь: | PULLEY EXIT A |
| Парткод: | 2BM21160 |
| Деталь: | PULLY EXIT C |
| Парткод: | 2BM21670 |
| Деталь: | COVER EXIT FU |
| Парткод: | 2BM21540 |
| Деталь: | Tray FU Assy |
| Парткод: | 2BM68190 |
| Деталь: | BAND TRAY |
| Парткод: | 2BM04210 |
| Деталь: | TRAY FU B |
| Парткод: | 2BM04200 |
| Деталь: | TRAY FU A |
| Парткод: | 2BM04190 |
| Деталь: | CONVEYING UNIT ASSY |
| Парткод: | 2A600230 |
| Деталь: | BUSH REGIST UP |
| Парткод: | 2BM17330 |
| Деталь: | GEAR REGIST Z24 |
| Парткод: | 2BM17950 |
| Деталь: | SPRING MIDDLE F |
| Парткод: | 2BM17350 |
| Деталь: | SPRING REGIST F |
| Парткод: | 2BM17420 |
| Деталь: | LOWER ROLLER,REGISTRATION |
| Парткод: | 2A606010 |
| Деталь: | JOINT ROLL TRANS |
| Парткод: | 2BM17390 |
| Деталь: | BUSH DRUM |
| Парткод: | 2BM21210 |
| Деталь: | GEAR REGIST Z32 |
| Парткод: | 2BM17380 |
| Деталь: | PT.SENSOR KR1207-KM |
| Парткод: | 2BM44070 |
| Деталь: | PLATE REG SENSOR |
| Парткод: | 2BM43250 |
| Деталь: | SLOPE IMAGE UNIT |
| Парткод: | 2BM43010 |
| Деталь: | PAD REG SENSOR |
| Парткод: | 2BM17440 |
| Деталь: | Latch Joint |
| Парткод: | 2BM17930 |
| Деталь: | PLATE EARTH CASE |
| Парткод: | 2BM17100 |
| Деталь: | ROLLER MIDDLE |
| Парткод: | 2BM17280 |
| Деталь: | SHAFT PULLEY MIDDLE |
| Парткод: | 2BM17300 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 2BM17310 |
| Деталь: | SPRING MIDDLE R |
| Парткод: | 2BM17360 |
| Деталь: | SPRING GUIDE MIDDLE |
| Парткод: | 2BM17340 |
| Деталь: | GUIDE MIDDLE |
| Парткод: | 2BM17290 |
| Деталь: | LEVER GUDIE MIDDLE |
| Парткод: | 2BM17320 |
| Деталь: | SHEET REGIST B |
| Парткод: | 2BM17500 |
| Деталь: | SHEET REGIST A |
| Парткод: | 2BM17490 |
| Деталь: | PLATE EARTH REG A |
| Парткод: | 2BM17460 |
| Деталь: | GUIDE PAPER REGIST |
| Парткод: | 2BM43260 |
| Деталь: | HIGH-MEG R ASSY |
| Парткод: | 2BM17480 |
| Деталь: | Plate Release |
| Парткод: | 2BM17120 |
| Деталь: | SPRING RELEASE |
| Парткод: | 2BM17130 |
| Деталь: | Case Low |
| Парткод: | 2BM17010 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 2BM17970 |
| Деталь: | GEAR JOINT Z22S |
| Парткод: | 2BM17260 |
| Деталь: | GEAR Z22S-Z14S |
| Парткод: | 2BM17270 |
| Деталь: | PLATE GEAR TC |
| Парткод: | 2BM17250 |
| Деталь: | PLATE CONTACT TRANS |
| Парткод: | 2BM17090 |
| Деталь: | PLATE CONTACT CHARGE |
| Парткод: | 2BM43130 |
| Деталь: | CONN CORD FEED DC ASSY |
| Парткод: | 2BM44040 |
| Деталь: | SEAL MASK PLATE |
| Парткод: | 2BM17110 |
| Деталь: | LEVER LOCK TB |
| Парткод: | 2BM17890 |
| Деталь: | HOLDER LOCK TB |
| Парткод: | 2BM17900 |
| Деталь: | SPRING LOCK TB |
| Парткод: | 2BM17910 |
| Деталь: | CONVEYING UNIT JUNCTION PCB ASSY |
| Парткод: | 2A601130 |
| Деталь: | CONN CORD FEED2 ASSY |
| Парткод: | 2BM27260 |
| Деталь: | GEAR IDLE Z24S |
| Парткод: | 2BM17240 |
| Деталь: | PLATE GEAR FUSER |
| Парткод: | 2BM17230 |
| Деталь: | FAN BELT |
| Парткод: | 2BM27230 |
| Деталь: | DUCT FEED UP |
| Парткод: | 2BM17510 |
| Деталь: | SEAL BELT LOW |
| Парткод: | 2BM17520 |
| Деталь: | SCREW FAN BELT |
| Парткод: | 2BM17960 |
| Деталь: | GUIDE LEFT ASSY |
| Парткод: | 2BM68160 |
| Деталь: | GUIDE CHANGE DU |
| Парткод: | 2BM17150 |
| Деталь: | PLATE LEVER SOL |
| Парткод: | 2BM17180 |
| Деталь: | HOOK LOCK FUSER |
| Парткод: | 2BM17170 |
| Деталь: | SOLENOID FEED |
| Парткод: | 2BM27160 |
| Деталь: | ANGLE SOLENOID |
| Парткод: | 2BM17190 |
| Деталь: | PLATE DU SENSOR |
| Парткод: | 2BM43100 |
| Деталь: | GUIDE CASE LOW LEFT |
| Парткод: | 2BM17140 |
| Деталь: | PT.SENSOR GP2S30 |
| Парткод: | 2BM27170 |
| Деталь: | LEVER LOCK CASE LOW |
| Парткод: | 2BM17160 |
| Деталь: | COVER GUIDE DU |
| Парткод: | 2BM17200 |
| Деталь: | REFLECTOR DU SENSOR |
| Парткод: | 2BM43120 |
| Деталь: | CONN.CORD FEED_EARTH ASSY |
| Парткод: | 2BM44030 |
| Деталь: | SPRING LOCK FUSER |
| Парткод: | 2BM17210 |
| Деталь: | SPRING SOLENOID |
| Парткод: | 2BM17220 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | PLATE SUPPORT FEED |
| Парткод: | 2BM43060 |
| Деталь: | PLATE BOTTOM FEED |
| Парткод: | 2BM17020 |
| Деталь: | PLATE FRONT LEVER |
| Парткод: | 2BM17030 |
| Деталь: | HOOK LEVER FRONT |
| Парткод: | 2BM17060 |
| Деталь: | PLATE EARTH BOTTOM |
| Парткод: | 2BM43070 |
| Деталь: | SPRING FRONT LEVER |
| Парткод: | 2BM17070 |
| Деталь: | COVER CL FEED |
| Парткод: | 2BM17680 |
| Деталь: | LEVER FEED FRONT |
| Парткод: | 2BM17050 |
| Деталь: | BELT ASSY |
| Парткод: | 2BM68170 |
| Деталь: | BUSH POM |
| Парткод: | 5MVM122DB003 |
| Деталь: | METAL BUSH KD |
| Парткод: | 5MMM176CJ003 |
| Деталь: | CLUTCH SP CAM |
| Парткод: | 2BM27210 |
| Деталь: | GEAR Z42S |
| Парткод: | 2BM17620 |
| Деталь: | CAM TRANS |
| Парткод: | 2BM17610 |
| Деталь: | BUSH TRANS UNIT |
| Парткод: | 2BM17600 |
| Деталь: | COVER RIGHT ASSY |
| Парткод: | 2BM00030 |
| Деталь: | COVER RIGHT |
| Парткод: | 2BM04150 |
| Деталь: | PLATE EARTH RC |
| Парткод: | 2BM04290 |
| Деталь: | SUPPORT COVER ASSY |
| Парткод: | 2BM04160 |
| Деталь: | COVER LEFT |
| Парткод: | 2BM04170 |
| Деталь: | POCKET,DATA |
| Парткод: | 2A604120 |
| Деталь: | COVER,COUNTER |
| Парткод: | 36504400 |
| Деталь: | PARTS,OPERATION UNIt(eUR)SP |
| Парткод: | 2A693050 |
| Деталь: | PARTS,OPERATION UNIT(USA)SP |
| Парткод: | 2A693040 |
| Деталь: | PROTECTION SHEET,OPERATION UNIT |
| Парткод: | 2A624060 |
| Деталь: | GROUND PLATE,OPERATION UNIT |
| Парткод: | 2A624050 |
| Деталь: | MOUNT,OPERATION UNIT |
| Парткод: | 2A624040 |
| Деталь: | SUPPORT PLATE,OPERATION UNIT |
| Парткод: | 2A624070 |
| Деталь: | JUNCTION WIRING,OPERATION UNIT KEYBOARD |
| Парткод: | 2A627390 |
| Деталь: | JUNCTION WIRING,OPERATION UNIT LED |
| Парткод: | 2A627400 |
| Деталь: | JUNCTION WIRING,LCD |
| Парткод: | 2A627410 |
| Деталь: | FRONT COVER (KM-C830) |
| Парткод: | 2A604020 |
| Деталь: | FRONT COVER B (KM-C830D) |
| Парткод: | 2A604510 |
| Деталь: | PLATE MAGCHATCH |
| Парткод: | 2BM04100 |
| Деталь: | BAND COVER |
| Парткод: | 2BM04280 |
| Деталь: | INNER LABEL,OPERATION |
| Парткод: | 2A605020 |
| Деталь: | UPPER COVER,PRINTER |
| Парткод: | 2A604010 |
| Деталь: | SP PRESS2 DLP |
| Парткод: | 2BM04030 |
| Деталь: | INNER LEFT COVER |
| Парткод: | 2A604050 |
| Деталь: | REAR COVER,SCANNER |
| Парткод: | 2A604070 |
| Деталь: | UPPER RIGHT COVER |
| Парткод: | 2A604030 |
| Деталь: | UPPER LEFT COVER |
| Парткод: | 2A604040 |
| Деталь: | LEFT PROTECTING PLATE,COVER |
| Парткод: | 2A604200 |
| Деталь: | LOWER REAR COVER |
| Парткод: | 2A604090 |
| Деталь: | UPPER REAR COVER |
| Парткод: | 2A604060 |
| Деталь: | LID,NIC |
| Парткод: | 2A626120 |
| Деталь: | LOWER COVER,OPERATION UNIT |
| Парткод: | 2A604080 |
| Деталь: | PROTECTOR OZONE |
| Парткод: | 2BM04270 |
| Деталь: | LOWER REAR RIGHT COVER |
| Парткод: | 2A604100 |
| Деталь: | REAR SHIELD,SCANNER |
| Парткод: | 2A612420 |
| Деталь: | REAR GROUND PLATE,SCANNER |
| Парткод: | 2A612430 |
| Деталь: | FRONT LABEL,COVER |
| Парткод: | 2A605030 |
| Деталь: | PROTECTING PLATE,DF CONNECTOR |
| Парткод: | 2A626140 |
| Деталь: | PARTS,DEVELOPING UNIT (Y),(USA) |
| Парткод: | 2A693090 |
| Деталь: | PARTS,DEVELOPING UNIT (y),(j/E) |
| Парткод: | 2A693100 |
| Деталь: | CASE DLP D1 |
| Парткод: | 2BM14660 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 2BM27330 |
| Деталь: | SENSOR FACE D1234 |
| Парткод: | 2BM14310 |
| Деталь: | SEAL SIDE D24 |
| Парткод: | 2BM40570 |
| Деталь: | MAGNET SEAL D1234 |
| Парткод: | 2BM40560 |
| Деталь: | SEAL CASE A D1 |
| Парткод: | 2BM14800 |
| Деталь: | SCRAPER PULLEY D1234 |
| Парткод: | 2BM14300 |
| Деталь: | MAGNET MIXER D1234 |
| Парткод: | 2BM14180 |
| Деталь: | SEAL BUSH D1234 |
| Парткод: | 2BM40190 |
| Деталь: | SPACER D1234 |
| Парткод: | 2BM40200 |
| Деталь: | OIL SEAL |
| Парткод: | 2BM14390 |
| Деталь: | BUSH D1234 |
| Парткод: | 2BM14330 |
| Деталь: | SHAFT T BRAKE D12 |
| Парткод: | 2BM14580 |
| Деталь: | GEAR Z28-5 D1234 |
| Парткод: | 2BM14210 |
| Деталь: | SHAFT CROSS D1 ASSY |
| Парткод: | 2BM00860 |
| Деталь: | SHAFT GEAR MIX 1 |
| Парткод: | 2BM40230 |
| Деталь: | GEAR Z28-5 MIX2 |
| Парткод: | 2BM40220 |
| Деталь: | GEAR MIXER 1 D123 |
| Парткод: | 2BM14410 |
| Деталь: | TUBE MIXER D1234 |
| Парткод: | 2BM14130 |
| Деталь: | FLANGE MIXER L D1234 |
| Парткод: | 2BM14150 |
| Деталь: | SCREW MIXER D1234 |
| Парткод: | 2BM14160 |
| Деталь: | SHAFT MIXER D123 |
| Парткод: | 2BM40100 |
| Деталь: | FLANGE MIXER R D1234 |
| Парткод: | 2BM14170 |
| Деталь: | SCRAPER MIXER D1234 |
| Парткод: | 2BM40580 |
| Деталь: | GEAR MIXER 2 D123 |
| Парткод: | 2BM14420 |
| Деталь: | STAY D1 |
| Парткод: | 2BM14670 |
| Деталь: | SEAL CASE D134 |
| Парткод: | 2BM14630 |
| Деталь: | SEAL BLADE D1234 |
| Парткод: | 2BM14320 |
| Деталь: | SEAL CASE D D1 |
| Парткод: | 2BM40120 |
| Деталь: | SEAL CASE D12 |
| Парткод: | 2BM14610 |
| Деталь: | SEAL CASE B D1 |
| Парткод: | 2BM14810 |
| Деталь: | SEAL CASE C D1 |
| Парткод: | 2BM14820 |
| Деталь: | SEAL CASE D123 |
| Парткод: | 2BM14500 |
| Деталь: | ROLLER MAGNET D4 |
| Парткод: | 2BM14620 |
| Деталь: | PULLY D1234 |
| Парткод: | 2BM14010 |
| Деталь: | GAER MG H D1234 |
| Парткод: | 2BM40460 |
| Деталь: | FLANGE R D1 |
| Парткод: | 2BM14680 |
| Деталь: | GEAR Z30-Z16 D12 |
| Парткод: | 2BM14590 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | ROLLER BLADE D1234 |
| Парткод: | 2BM14030 |
| Деталь: | SHAFT MG BLADE D1234 |
| Парткод: | 2BM14040 |
| Деталь: | BUSH BIAS D1234 |
| Парткод: | 2BM14220 |
| Деталь: | SP MG BLADE D1234 |
| Парткод: | 2BM14290 |
| Деталь: | JOINT MG D1234 |
| Парткод: | 2BM14050 |
| Деталь: | GAER Z20H D12 |
| Парткод: | 2BM40420 |
| Деталь: | GAER Z20H R D12 |
| Парткод: | 2BM40430 |
| Деталь: | PITCH PIECE R D1 |
| Парткод: | 2BM14690 |
| Деталь: | PITCH PIECE F D1 |
| Парткод: | 2BM14720 |
| Деталь: | BIAS JOINT D123 |
| Парткод: | 2BM14400 |
| Деталь: | PLATE ANGLE D123 |
| Парткод: | 2BM14440 |
| Деталь: | PRESSDCUT D1234 |
| Парткод: | 2BM40040 |
| Деталь: | PLATE IDLE D1 |
| Парткод: | 2BM14850 |
| Деталь: | GEAR Z20-5 D1234 |
| Парткод: | 2BM14110 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | GEAR Z30-5 D1 |
| Парткод: | 2BM14840 |
| Деталь: | COVER F D1 |
| Парткод: | 2BM14780 |
| Деталь: | SEAL MG D1234 |
| Парткод: | 2BM40300 |
| Деталь: | BKT CLUTCH D1 |
| Парткод: | 2BM14700 |
| Деталь: | GEAR Z30H-Z22H D12 |
| Парткод: | 2BM40640 |
| Деталь: | CLUTCH 26-D |
| Парткод: | 2BM27350 |
| Деталь: | SEAL CLUTH D1234 |
| Парткод: | 2BM40150 |
| Деталь: | SHAFT CLUTCH D1234 |
| Парткод: | 2BM14070 |
| Деталь: | JOINT D1234 |
| Парткод: | 2BM14090 |
| Деталь: | POLY WASHER 16 |
| Парткод: | 2BM40500 |
| Деталь: | BALL BEARING D1234 |
| Парткод: | 2BM40310 |
| Деталь: | POLY WASHER 14 |
| Парткод: | 2BM40510 |
| Деталь: | GEAR Z14D-8 D1234 |
| Парткод: | 2BM40360 |
| Деталь: | GEAR Z15-8 D123 |
| Парткод: | 2BM40370 |
| Деталь: | GEAR Z14-Z12 D123 |
| Парткод: | 2BM40590 |
| Деталь: | SHAFT GEAR D12 |
| Парткод: | 2BM14570 |
| Деталь: | Bush |
| Парткод: | 2BM14530 |
| Деталь: | GEAR Z14-8 JOINT D12 |
| Парткод: | 2BM14560 |
| Деталь: | GUIDE TCNT D1 |
| Парткод: | 2BM14710 |
| Деталь: | GUIDE SHUTTER D1234 |
| Парткод: | 2BM14200 |
| Деталь: | SEAL GUIDE T D1234 |
| Парткод: | 2BM14260 |
| Деталь: | SEAL SHUTTER D1234 |
| Парткод: | 2BM14250 |
| Деталь: | SHUTTER D1234 |
| Парткод: | 2BM14240 |
| Деталь: | SPRING SHUTTER D1234 |
| Парткод: | 2BM14230 |
| Деталь: | LOCK SHUTTER D1234 |
| Парткод: | 2BM14120 |
| Деталь: | PW.BOARD KP-819 ASSY |
| Парткод: | 2BM01140 |
| Деталь: | CONN.CORD LED D1 ASSY |
| Парткод: | 2BM27370 |
| Деталь: | GUIDE SCREW D14 |
| Парткод: | 2BM14640 |
| Деталь: | WIRE Y,DEVELOPING |
| Парткод: | 2A627600 |
| Деталь: | SIMM D1 |
| Парткод: | 2BM40710 |
| Деталь: | GEAR Z20-8 D12 |
| Парткод: | 2BM14600 |
| Деталь: | PLATE MOTOR TONER D1 |
| Парткод: | 2BM14730 |
| Деталь: | GEAR Z31-Z15-8 D123 |
| Парткод: | 2BM14460 |
| Деталь: | SP JOINT T SRP D1 |
| Парткод: | 2BM14830 |
| Деталь: | JOINT SCRAPER CI D |
| Парткод: | 2A614070 |
| Деталь: | DC motor |
| Парткод: | 2BM27340 |
| Деталь: | GEAR WORM |
| Парткод: | 2BM14540 |
| Деталь: | CONN.CORD TM D1 ASSY |
| Парткод: | 2BM27390 |
| Деталь: | JOINT FEED T D123 |
| Парткод: | 2BM14470 |
| Деталь: | SP JOINT T SW D1234 |
| Парткод: | 2BM14190 |
| Деталь: | BKT JOINT TCNT D1 |
| Парткод: | 2BM14740 |
| Деталь: | WORM WHEEL D123 |
| Парткод: | 2BM14480 |
| Деталь: | LABEL POSITION Y |
| Парткод: | 2BM05180 |
| Деталь: | COVER TCNT R D1 |
| Парткод: | 2BM14760 |
| Деталь: | PW.BOARD KP-820 ASSY |
| Парткод: | 2BM01150 |
| Деталь: | CONN.CORD PTR D1 ASSY |
| Парткод: | 2BM27380 |
| Деталь: | DETECTION PLATE D14,DEVELOPING(F) |
| Парткод: | 2A614010 |
| Деталь: | DETECTION PLATE D14,DEVELOPING(G) |
| Парткод: | 2A614020 |
| Деталь: | COVER R D1 |
| Парткод: | 2BM14750 |
| Деталь: | COVER MAG D1 |
| Парткод: | 2BM14770 |
| Деталь: | SHEET COVER MAG D1 |
| Парткод: | 2BM14860 |
| Деталь: | SEAL LID DEVE D1234 |
| Парткод: | 2BM14270 |
| Деталь: | COVER TCNT F D1 |
| Парткод: | 2BM14790 |
| Деталь: | SHEET PWB D1234 |
| Парткод: | 2BM40140 |
| Деталь: | SIMM D1234 |
| Парткод: | 2BM40700 |
| Деталь: | STAY BASE L UNIT |
| Парткод: | 2BM00920 |
| Деталь: | STAY BASE L |
| Парткод: | 2BM02870 |
| Деталь: | FOOT R |
| Парткод: | 2BM42290 |
| Деталь: | STAY BASE R UNIT |
| Парткод: | 2BM00930 |
| Деталь: | STAY BASE R |
| Парткод: | 2BM02860 |
| Деталь: | FRAME FRONT ASSY |
| Парткод: | 2BM00110 |
| Деталь: | Frame Front |
| Парткод: | 2BM02010 |
| Деталь: | STAY RAIL FRONT |
| Парткод: | 2BM02030 |
| Деталь: | CHANNEL BOTTOM |
| Парткод: | 2BM02020 |
| Деталь: | PILOT PIN |
| Парткод: | 2BM02040 |
| Деталь: | FOOT F |
| Парткод: | 2BM42300 |
| Деталь: | SHEET INNER FRONT |
| Парткод: | 2BM42210 |
| Деталь: | PLATE EARTH MAIN B |
| Парткод: | 2BM42530 |
| Деталь: | FRAME BASE ASSY |
| Парткод: | 2BM00140 |
| Деталь: | FRAME BASE |
| Парткод: | 2BM02510 |
| Деталь: | BASE PULLEY FEED |
| Парткод: | 2BM02530 |
| Деталь: | PULLEY FEED |
| Парткод: | 2BM02540 |
| Деталь: | LOCK PIN |
| Парткод: | 2BM02520 |
| Деталь: | DUCT BASE LOW |
| Парткод: | 2BM02580 |
| Деталь: | SHEET DUCT A |
| Парткод: | 2BM42070 |
| Деталь: | PLATE EARTH LOWER |
| Парткод: | 2BM02550 |
| Деталь: | SHIELD REG SENSOR B |
| Парткод: | 2BM42740 |
| Деталь: | HOLDER HARNESS |
| Парткод: | 2BM02480 |
| Деталь: | PLATE EARTH MAIN |
| Парткод: | 2BM02390 |
| Деталь: | PWB HV MAIN |
| Парткод: | 2BM28240 |
| Деталь: | SPRING SW DU |
| Парткод: | 2BM02900 |
| Деталь: | SWITCH DU |
| Парткод: | 2BM02910 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | PLATE EARTH DC |
| Парткод: | 2BM02400 |
| Деталь: | PWBHVTC |
| Парткод: | 2BM28260 |
| Деталь: | PW.BOARD KP-830 ASSY |
| Парткод: | 2BM01200 |
| Деталь: | PLATE EARTH TC |
| Парткод: | 2BM02410 |
| Деталь: | PLATE EARTH OP |
| Парткод: | 2BM02420 |
| Деталь: | PLATE EARTH DRV FUS |
| Парткод: | 2BM42520 |
| Деталь: | FRAME REAR |
| Парткод: | 2BM02070 |
| Деталь: | BUSH PIN OVAL |
| Парткод: | 2BM02440 |
| Деталь: | BUSH PIN |
| Парткод: | 2BM02430 |
| Деталь: | PLATE HV IM |
| Парткод: | 2BM02150 |
| Деталь: | COVER HV IMAGE |
| Парткод: | 2BM02140 |
| Деталь: | SPRING HV S |
| Парткод: | 2BM02160 |
| Деталь: | PIN CONTACT HV |
| Парткод: | 2BM02110 |
| Деталь: | COVER HV FEED |
| Парткод: | 2BM02170 |
| Деталь: | PLATE HV DC |
| Парткод: | 2BM02190 |
| Деталь: | PLATE HV TC |
| Парткод: | 2BM02180 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 2BM68100 |
| Деталь: | PW.BOARD KP-849 ASSY |
| Парткод: | 2BM01230 |
| Деталь: | CONN.CORD T.SENSOR ASSY |
| Парткод: | 2BM28780 |
| Деталь: | BRACKET SENSOR WASTE |
| Парткод: | 2BM18510 |
| Деталь: | SEAL SENSOR WASTE |
| Парткод: | 2BM18520 |
| Деталь: | PLATE HV D1 |
| Парткод: | 2BM02090 |
| Деталь: | PLATE HV D2 |
| Парткод: | 2BM02100 |
| Деталь: | BRACKET CONN DRUM |
| Парткод: | 2BM42030 |
| Деталь: | SPRING CONN DRUM |
| Парткод: | 2BM42440 |
| Деталь: | BRACKET CONN D12 |
| Парткод: | 2BM02200 |
| Деталь: | SPRING CONNECTOR |
| Парткод: | 2BM02220 |
| Деталь: | BRACKET CONN D34 |
| Парткод: | 2BM02230 |
| Деталь: | PWD HV DLP |
| Парткод: | 2BM28270 |
| Деталь: | STUD SCREW 485 |
| Парткод: | 2BM42450 |
| Деталь: | SPRING CONN FEED |
| Парткод: | 2BM42010 |
| Деталь: | PLATE ANKER A |
| Парткод: | 2BM02490 |
| Деталь: | STUD SCREW 465 |
| Парткод: | 2BM41080 |
| Деталь: | RAIL LOW R ASSY |
| Парткод: | 2BM00160 |
| Деталь: | STAY RAIL LOW R B |
| Парткод: | 2BM02640 |
| Деталь: | SHIELD REG SENSOR A |
| Парткод: | 2BM42730 |
| Деталь: | SLIDE RAIL LOW |
| Парткод: | 2BM02670 |
| Деталь: | STAY RAIL LOW R A |
| Парткод: | 2BM02630 |
| Деталь: | RAIL LOW L ASSY |
| Парткод: | 2BM00170 |
| Деталь: | STAY RAIL LOW L A |
| Парткод: | 2BM02650 |
| Деталь: | STAY RAIL LOW L B |
| Парткод: | 2BM02660 |
| Деталь: | HOLDER FRONT |
| Парткод: | 2BM02930 |
| Деталь: | SCREW CONNECTOR |
| Парткод: | 2BM02210 |
| Деталь: | DUCT WASTE TONER UNIT |
| Парткод: | 2BM00950 |
| Деталь: | HOLDER SW OIL ASSY |
| Парткод: | 2BM68120 |
| Деталь: | RAIL PRO L ASSY |
| Парткод: | 2BM00190 |
| Деталь: | STAY RAIL PRO L A |
| Парткод: | 2BM02750 |
| Деталь: | SLIDE RAIL PRO |
| Парткод: | 2BM02700 |
| Деталь: | STAY RAIL PRO L B |
| Парткод: | 2BM02760 |
| Деталь: | SEAL RAIL PRO B |
| Парткод: | 2BM42630 |
| Деталь: | SEAL STAY PRO A |
| Парткод: | 2BM42620 |
| Деталь: | PLATE SCANNER BASE |
| Парткод: | 2BM02850 |
| Деталь: | FEED TONER D4 ASSY |
| Парткод: | 2BM00790 |
| Деталь: | FEED TONER ASSY |
| Парткод: | 2BM68090 |
| Деталь: | SEAL FEED TK C |
| Парткод: | 2BM15970 |
| Деталь: | CASE FEED TK |
| Парткод: | 2BM15910 |
| Деталь: | SCREW FEED TK |
| Парткод: | 2BM15930 |
| Деталь: | SEAL FEED TK B |
| Парткод: | 2BM15960 |
| Деталь: | BUSH FEED TK |
| Парткод: | 2BM15920 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM42280 |
| Деталь: | BKT SEAL OIL |
| Парткод: | 2BM42240 |
| Деталь: | OIL SEAL |
| Парткод: | 2BM14390 |
| Деталь: | BUSH SCREW TK F |
| Парткод: | 2BM42220 |
| Деталь: | GEAR FEED TK Z23 |
| Парткод: | 2BM42250 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | SEAL FEED TK A |
| Парткод: | 2BM15950 |
| Деталь: | PLATE FEED TK |
| Парткод: | 2BM15940 |
| Деталь: | SEAL FEED TK D |
| Парткод: | 2BM42310 |
| Деталь: | GUIDE SCREW D14 |
| Парткод: | 2BM14640 |
| Деталь: | GUIDE SHUTTER D1234 |
| Парткод: | 2BM14200 |
| Деталь: | SEAL GUIDE T D1234 |
| Парткод: | 2BM14260 |
| Деталь: | SEAL SHUTTER D1234 |
| Парткод: | 2BM14250 |
| Деталь: | SHUTTER D1234 |
| Парткод: | 2BM14240 |
| Деталь: | SPRING SHUTTER D1234 |
| Парткод: | 2BM14230 |
| Деталь: | STAY MIDDLE ASSY |
| Парткод: | 2BM00150 |
| Деталь: | LOCK SHUTTER D1234 |
| Парткод: | 2BM14120 |
| Деталь: | SEAL FEED TONER |
| Парткод: | 2BM42600 |
| Деталь: | SEAL FEED TK E |
| Парткод: | 2BM42480 |
| Деталь: | RAIL PRO R ASSY |
| Парткод: | 2BM00180 |
| Деталь: | STAY RAIL PRO R B |
| Парткод: | 2BM02690 |
| Деталь: | STAY PRO R ASSY |
| Парткод: | 2BM02680 |
| Деталь: | SUPPORT PULLEY TRANS |
| Парткод: | 2BM02730 |
| Деталь: | BKT PULLEY IMAGE |
| Парткод: | 2BM02720 |
| Деталь: | PULLEY IMAGE L |
| Парткод: | 2BM02740 |
| Деталь: | GUIDE CONTAINER D4 |
| Парткод: | 2BM02710 |
| Деталь: | RAIL IMAGE R ASSY |
| Парткод: | 2BM00200 |
| Деталь: | RAIL IMAGE R |
| Парткод: | 2BM02780 |
| Деталь: | STOPPER IMAGE |
| Парткод: | 2BM42040 |
| Деталь: | BRACKET LOCK IMAGE |
| Парткод: | 2BM02790 |
| Деталь: | PULLEY IMAGE |
| Парткод: | 2BM02810 |
| Деталь: | LEVER LOCK IMAGE |
| Парткод: | 2BM02800 |
| Деталь: | SPRING LOCK IMAGE |
| Парткод: | 2BM02820 |
| Деталь: | GUIDE PAPER IN |
| Парткод: | 2BM02560 |
| Деталь: | P.W.BOARD KP-896 ASSY |
| Парткод: | 2BM01270 |
| Деталь: | BKT SENSOR LOW D4 |
| Парткод: | 2BM42260 |
| Деталь: | COVER HV DLP |
| Парткод: | 2BM02890 |
| Деталь: | INNER FRONT COVER |
| Парткод: | 2BM04310 |
| Деталь: | MAGNET CATCH |
| Парткод: | 60804120 |
| Деталь: | LEVER INTER LOCK |
| Парткод: | 2BM02060 |
| Деталь: | INTERLOCK SWITCH |
| Парткод: | 2BM26130 |
| Деталь: | GUIDE PAPER OUT |
| Парткод: | 2BM02570 |
| Деталь: | PLATE EARTH L |
| Парткод: | 2BM42560 |
| Деталь: | PLATE EARTH FG |
| Парткод: | 2BM42570 |
| Деталь: | LK-800 SCANNER UNIT |
| Парткод: | 5PLPXBEAPKX |
| Деталь: | BKT SENSOR UP D4 |
| Парткод: | 2BM42270 |
| Деталь: | P.W.BOARD KP-895 ASSY |
| Парткод: | 2BM01260 |
| Деталь: | PLATE EARTH DRV TK A |
| Парткод: | 2BM42540 |
| Деталь: | PWB HV DC |
| Парткод: | 2BM28250 |
| Деталь: | COVER HV DRUM |
| Парткод: | 2BM02080 |
| Деталь: | SPRING HV L |
| Парткод: | 2BM02120 |
| Деталь: | DETECTION PLATE D14,DEVELOPING(F) |
| Парткод: | 2A614010 |
| Деталь: | DETECTION PLATE D14,DEVELOPING(G) |
| Парткод: | 2A614020 |
| Деталь: | CONT BOX |
| Парткод: | 2BM01020 |
| Деталь: | BOX CONTROLLER ASSY |
| Парткод: | 2BM00960 |
| Деталь: | PW.BOARD KP-802 ASSY |
| Парткод: | 2BM01070 |
| Деталь: | POWER SOURCE ASSY(100) |
| Парткод: | 2A601090 |
| Деталь: | POWER SOURCE ASSY(200) |
| Парткод: | 2A601103 |
| Деталь: | POWER SOURCE ASSy(200 EXP) |
| Парткод: | 2A601150 |
| Деталь: | EDGING,EDS-1717U |
| Парткод: | M2104220 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | MOUNT,POWER SOURCE |
| Парткод: | 2A626090 |
| Деталь: | MOUNT FAN |
| Парткод: | 2A626130 |
| Деталь: | WIRE,PRIMARY |
| Парткод: | 2A627470 |
| Деталь: | WIRE,ENGINE MAIN PCB POWER SOURCE |
| Парткод: | 2A627680 |
| Деталь: | FAN,COOLING |
| Парткод: | 34927070 |
| Деталь: | POWER SOURCE PCB(100) |
| Парткод: | 2A628060 |
| Деталь: | POWER SOURCE PCB(200) |
| Парткод: | 2A628070 |
| Деталь: | FUSE,CES6-N1(SOC) |
| Парткод: | M5561000 |
| Деталь: | FUSE,21506.3(LITTEL-FUSE) |
| Парткод: | M1656050 |
| Деталь: | FUSE,CES6-N1-10A(SOC) |
| Парткод: | M5560020 |
| Деталь: | CONN.CORD PS1 ASSY |
| Парткод: | 2BM27860 |
| Деталь: | CORE 11-25X14 |
| Парткод: | 2A627930 |
| Деталь: | ENGINE MAIN PCB MOUNT ASSY |
| Парткод: | 2A601110 |
| Деталь: | MOUNT,MAIN PCB |
| Парткод: | 2A626220 |
| Деталь: | FAN MOTOR |
| Парткод: | 2BM27970 |
| Деталь: | JUNCTION WIRING,INTERFACE CONTROL |
| Парткод: | 2A627650 |
| Деталь: | JUNCTION WIRING,INTERFACE DATA |
| Парткод: | 2A627660 |
| Деталь: | WIRE,ENGINE MAIN PCB |
| Парткод: | 2A627170 |
| Деталь: | WIRE,FACE DOWN |
| Парткод: | 2A627510 |
| Деталь: | SPACER,KGLS-3S |
| Парткод: | M2108000 |
| Деталь: | SPACER,PHD-08(KITAGAWA) |
| Парткод: | M2108600 |
| Деталь: | PLATE CONTROLLER A |
| Парткод: | 2BM42510 |
| Деталь: | WIRE,POWER SOURCE DETECTION |
| Парткод: | 2A627800 |
| Деталь: | ENGINE MAIN PCB ASSY |
| Парткод: | 2A601060 |
| Деталь: | PARTS,PCB ENGINE INTERFACE(SP) |
| Парткод: | 2A693010 |
| Деталь: | DR-800B(DRIVE UNIT B) |
| Парткод: | 2BM93050 |
| Деталь: | PLATE DRIVE FEED C |
| Парткод: | 2BM22570 |
| Деталь: | EDGING,EDS-0607U(KITAGAWA) |
| Парткод: | M2104260 |
| Деталь: | GEAR Z23 JO |
| Парткод: | 2BM22640 |
| Деталь: | GEAR Z26 |
| Парткод: | 2BM22620 |
| Деталь: | GEAR Z33 Z23 |
| Парткод: | 2BM22650 |
| Деталь: | GEAR Z21 |
| Парткод: | 2BM22690 |
| Деталь: | GEAR Z14 Z30 |
| Парткод: | 2BM22630 |
| Деталь: | SPRING JOINT LOW |
| Парткод: | 2BM22850 |
| Деталь: | GEAR Z25 JOINT |
| Парткод: | 2BM22660 |
| Деталь: | BUSH METAL |
| Парткод: | 2BM07330 |
| Деталь: | GEAR Z22 JOINT BE |
| Парткод: | 2BM22670 |
| Деталь: | SHAFT JOINT BEVEL |
| Парткод: | 2BM22830 |
| Деталь: | PLATE DRIVE FEED B |
| Парткод: | 2BM22560 |
| Деталь: | MOTOR MAIN |
| Парткод: | 2BM27690 |
| Деталь: | BUSH SHAFT 6 |
| Парткод: | 2BM22760 |
| Деталь: | GEAR Z14 Z36 |
| Парткод: | 2BM22700 |
| Деталь: | GEAR Z30 Z66H |
| Парткод: | 2BM22580 |
| Деталь: | Gear Z36 |
| Парткод: | 2BM22610 |
| Деталь: | GEAR Z33 Z47H |
| Парткод: | 2BM22590 |
| Деталь: | GEAR Z24 |
| Парткод: | 2BM22600 |
| Деталь: | GEAR Z29 JO |
| Парткод: | 2BM22740 |
| Деталь: | GEAR BEVEL Z20 |
| Парткод: | 2BM22680 |
| Деталь: | CLUTCH REGIST |
| Парткод: | 2BM27750 |
| Деталь: | SHAFT JOINT REGIST |
| Парткод: | 2BM22820 |
| Деталь: | CLUTCH 26-A |
| Парткод: | 2BM27760 |
| Деталь: | SHAFT JOINT MID |
| Парткод: | 2BM22810 |
| Деталь: | PLATE DRIVE FEED A |
| Парткод: | 2BM22550 |
| Деталь: | BUSH CLUTCH D1234 |
| Парткод: | 2BM14060 |
| Деталь: | HOUSING CL REGIST |
| Парткод: | 2BM22750 |
| Деталь: | SPRING JOINT REGIST |
| Парткод: | 2BM22840 |
| Деталь: | JOINT ROLL REGIST |
| Парткод: | 2BM22790 |
| Деталь: | GEAR Z27 Z40 |
| Парткод: | 2BM22710 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | PW.BOARD KP-822 ASSY |
| Парткод: | 2BM01160 |
| Деталь: | TONER CONT. DRIVE ASSY |
| Парткод: | 2A600220 |
| Деталь: | PLATE DRIVE TK |
| Парткод: | 2BM22860 |
| Деталь: | BUSH POM MID |
| Парткод: | 2BM22770 |
| Деталь: | GEAR Z23 TK1 |
| Парткод: | 2BM23690 |
| Деталь: | GEAR Z21 Z36 |
| Парткод: | 2BM22920 |
| Деталь: | GEAR Z24 L |
| Парткод: | 2BM22950 |
| Деталь: | GEAR Z37 BEVEL Z25 |
| Парткод: | 2BM23710 |
| Деталь: | GEAR Z14 Z40 |
| Парткод: | 2BM22930 |
| Деталь: | GEAR Z41 |
| Парткод: | 2BM22940 |
| Деталь: | GEAR Z23 Z33 |
| Парткод: | 2BM22910 |
| Деталь: | SPRING JOINT TK |
| Парткод: | 2BM22990 |
| Деталь: | JOINT SCRAPER CI |
| Парткод: | 2A622010 |
| Деталь: | JOINT TK FEED |
| Парткод: | 2BM22880 |
| Деталь: | GEAR Z23 TK2 |
| Парткод: | 2BM23700 |
| Деталь: | SHAFT JOINT TK |
| Парткод: | 2BM22980 |
| Деталь: | GEAR Z30 CL TK |
| Парткод: | 2BM22970 |
| Деталь: | CLUTCH 26-G |
| Парткод: | 2BM27950 |
| Деталь: | HOLDER CL TK |
| Парткод: | 2BM22870 |
| Деталь: | DRIVE ASSY C |
| Парткод: | 2BM68110 |
| Деталь: | HOLDER STMOTOR |
| Парткод: | 2BM23610 |
| Деталь: | PLATE DRIVE FUSER A |
| Парткод: | 2BM23510 |
| Деталь: | GEAR Z40 JO |
| Парткод: | 2BM23570 |
| Деталь: | GEAR Z51 |
| Парткод: | 2BM23560 |
| Деталь: | SPRING LEVER |
| Парткод: | 2BM22440 |
| Деталь: | PLATE PULLEY |
| Парткод: | 2BM23530 |
| Деталь: | PULLEY BELT |
| Парткод: | 2BM23580 |
| Деталь: | GEAR P50 Z23 |
| Парткод: | 2BM23540 |
| Деталь: | BELT S2M138 |
| Парткод: | 2BM23630 |
| Деталь: | Bushing SBK |
| Парткод: | 5MMM176CJ005 |
| Деталь: | GEAR Z46 JOINT FUSER |
| Парткод: | 2BM23550 |
| Деталь: | BUSH MAG |
| Парткод: | 5MVM170XN002 |
| Деталь: | HOLDER SHAFT FUSER |
| Парткод: | 2BM23520 |
| Деталь: | SHAFT JOINT FUSER |
| Парткод: | 2BM23600 |
| Деталь: | JOINT FUSER |
| Парткод: | 2BM23590 |
| Деталь: | SPRING JOINT FUSER |
| Парткод: | 2BM23620 |
| Деталь: | MOTOR STEP |
| Парткод: | 2BM27790 |
| Деталь: | ORIGINAL HOLDER ASSY |
| Парткод: | 2AV60010 |
| Деталь: | COVER A,PLATEN |
| Парткод: | 2AV12370 |
| Деталь: | COVER B,PLATEN |
| Парткод: | 2AV12380 |
| Деталь: | RIGHT BASE,MAT |
| Парткод: | 2AV12390 |
| Деталь: | RIGHT MOVING PLATE,MAT |
| Парткод: | 2AV12400 |
| Деталь: | LEFT MOVING PLATE,MAT |
| Парткод: | 2AV12410 |
| Деталь: | BASE,MAT |
| Парткод: | 2AV12420 |
| Деталь: | MAT,ORIGINAL HOLDER |
| Парткод: | 19012041 |
| Деталь: | SHEET,ORIGINAL HOLDER |
| Парткод: | 19012050 |
| Деталь: | HINGE,ORIGINAL HOLDER |
| Парткод: | 19012060 |
| Деталь: | ORIGINAL POCKET |
| Парткод: | 60904280 |
| Деталь: | HINGE,ORIGINAL HOLDER |
| Парткод: | 60904310 |
| Деталь: | ACTUTATION PLATE,ORIGINAL DETECTION SWIT |
| Парткод: | 66012180 |
| Деталь: | PLATE SPRING,ORIGINAL HOLDER |
| Парткод: | 69312110 |
| Деталь: | ORIGINAL HOLDER SPACER |
| Парткод: | 79904140 |
| Деталь: | PARTS,FIXING UNIT 120 |
| Парткод: | 2A693170 |
| Деталь: | PARTS,FIXING UNIT 230 |
| Парткод: | 2A693180 |
| Деталь: | HANDLE GEAR |
| Парткод: | 2BM20500 |
| Деталь: | COVER REAR FUSER |
| Парткод: | 2BM20380 |
| Деталь: | WIRE,FIXING |
| Парткод: | 2A627640 |
| Деталь: | STUD SCREW 465 |
| Парткод: | 2BM41080 |
| Деталь: | SPRING CONNECTOR |
| Парткод: | 2BM20430 |
| Деталь: | LOCK PLATE PUSH |
| Парткод: | 2BM20540 |
| Деталь: | PLATE LOCK GEAR |
| Парткод: | 2BM20530 |
| Деталь: | GEAR LOCK Z10 |
| Парткод: | 2BM20510 |
| Деталь: | SPRING LOCK GEAR |
| Парткод: | 2BM20550 |
| Деталь: | BKT LAMP REAR |
| Парткод: | 2BM20410 |
| Деталь: | GEAR FUSER Z43 |
| Парткод: | 2BM20030 |
| Деталь: | BEARING FUSER |
| Парткод: | 2BM20040 |
| Деталь: | GEAR INPUT Z30 |
| Парткод: | 2BM20450 |
| Деталь: | GEAR IDLE Z24 |
| Парткод: | 2BM20460 |
| Деталь: | GEAR EXIT ROLL Z18 |
| Парткод: | 2BM20520 |
| Деталь: | BUSH DRUM |
| Парткод: | 2BM21210 |
| Деталь: | FRAME REAR FUSER |
| Парткод: | 2BM20150 |
| Деталь: | PLATE PRESS REAR |
| Парткод: | 2BM20160 |
| Деталь: | PLATE PIN PRESSURE |
| Парткод: | 2BM41010 |
| Деталь: | PIN PRESSURE |
| Парткод: | 2BM20170 |
| Деталь: | ROLLER EXIT |
| Парткод: | 2BM20560 |
| Деталь: | ROLLER FIX |
| Парткод: | 2BM20010 |
| Деталь: | ROLLER PRESS |
| Парткод: | 2BM20020 |
| Деталь: | FRAME TOP FUSER |
| Парткод: | 2BM20270 |
| Деталь: | BKT THERMOSTAT |
| Парткод: | 2BM20310 |
| Деталь: | NUT FUSER A |
| Парткод: | 5MMT163SN006 |
| Деталь: | BKT THERMISTER UP |
| Парткод: | 2BM20290 |
| Деталь: | THERMISTOR UP |
| Парткод: | 2BM20830 |
| Деталь: | THERMOSTAT |
| Парткод: | 2BM20850 |
| Деталь: | HOLDER HERNESS TOP R |
| Парткод: | 2BM20280 |
| Деталь: | GUIDE ENTRANCE UP |
| Парткод: | 2BM20340 |
| Деталь: | GUIDE ENTRANCE LOW |
| Парткод: | 2BM20330 |
| Деталь: | HOLDER HARNESS RR |
| Парткод: | 2BM20070 |
| Деталь: | HOLDER HARNESS R.F |
| Парткод: | 2BM20060 |
| Деталь: | THERMISTOR LOW |
| Парткод: | 2BM20840 |
| Деталь: | Frame Bottom |
| Парткод: | 2BM20050 |
| Деталь: | COVER BOTTOM FUSER |
| Парткод: | 2BM20360 |
| Деталь: | HOLDER HARNESS LOWER |
| Парткод: | 2BM20080 |
| Деталь: | LAMP HEATER UPPER 240 |
| Парткод: | 2BM20860 |
| Деталь: | LAMP HEATER UPPER 120 |
| Парткод: | 2BM20880 |
| Деталь: | LAMP HEATER LOW 240 |
| Парткод: | 2BM20870 |
| Деталь: | LAMP HEATER LOW 120 |
| Парткод: | 2BM20890 |
| Деталь: | PLATE PRESS FRONT |
| Парткод: | 2BM20140 |
| Деталь: | FRAME FRONT FUSER |
| Парткод: | 2BM20090 |
| Деталь: | BKT LAMP FRONT |
| Парткод: | 2BM20400 |
| Деталь: | P.W.BOARD KP-811 ASSY |
| Парткод: | 2BM01100 |
| Деталь: | COVER FRONT FUSER |
| Парткод: | 2BM20370 |
| Деталь: | GEAR IDLE Z24Z16 |
| Парткод: | 2BM20480 |
| Деталь: | GEAR IDLE Z30 |
| Парткод: | 2BM20490 |
| Деталь: | GEAR IDLE Z32Z14 |
| Парткод: | 2BM20470 |
| Деталь: | SOLENOID FUSER |
| Парткод: | 2BM27740 |
| Деталь: | CASE SOLENOID |
| Парткод: | 2BM20100 |
| Деталь: | ACTUATOR CLUTCH |
| Парткод: | 2BM20120 |
| Деталь: | PIN ACTUATOR CLUTCH |
| Парткод: | 2BM20110 |
| Деталь: | SPRING SOL |
| Парткод: | 2BM20130 |
| Деталь: | LABEL CAUTION S |
| Парткод: | 2BM42710 |
| Деталь: | BKT SEPARATOR UP |
| Парткод: | 2BM20220 |
| Деталь: | SPRING SEPARETOR |
| Парткод: | 2BM20260 |
| Деталь: | SEPARATOR UP |
| Парткод: | 2BM20240 |
| Деталь: | STAY SEPARATOR UP |
| Парткод: | 2BM20230 |
| Деталь: | SHEET PROTECT STAY |
| Парткод: | 2BM20250 |
| Деталь: | BKT SEPARETOR LOW |
| Парткод: | 2BM20190 |
| Деталь: | SEPARETOR LOW |
| Парткод: | 2BM20210 |
| Деталь: | STAY SEPARATOR LOW |
| Парткод: | 2BM20200 |
| Деталь: | BKT COVER TOP R |
| Парткод: | 2BM20680 |
| Деталь: | SPRING OIL UNIT |
| Парткод: | 2BM20800 |
| Деталь: | LOCK OIL UNIT |
| Парткод: | 2BM20690 |
| Деталь: | SPRING LOCK R |
| Парткод: | 2BM20820 |
| Деталь: | LOCK COVER TOP R |
| Парткод: | 2BM20710 |
| Деталь: | LEVER OIL R |
| Парткод: | 2BM20740 |
| Деталь: | PIN ACTUATOR OIL |
| Парткод: | 2BM20660 |
| Деталь: | BUSH OIL SHAFT |
| Парткод: | 2BM41090 |
| Деталь: | CAM ROLLER OIL |
| Парткод: | 2BM20630 |
| Деталь: | COVER SHAFT OIL |
| Парткод: | 2BM20750 |
| Деталь: | SHAFT MECH CLUTCH |
| Парткод: | 2BM20620 |
| Деталь: | SEAL FUSER UP |
| Парткод: | 2BM42680 |
| Деталь: | LABEL CAUTION FUSER |
| Парткод: | 2BM05090 |
| Деталь: | LABEL FUSER |
| Парткод: | 2BM05080 |
| Деталь: | PARTS,DRUM UNIT |
| Парткод: | 2A693080 |
| Деталь: | SEAL SHUTTER DRUM |
| Парткод: | 2BM18360 |
| Деталь: | SPRING CONTACT GRID |
| Парткод: | 2BM18440 |
| Деталь: | SPRING CONTACT MCH |
| Парткод: | 2BM18290 |
| Деталь: | COVER DRUM R |
| Парткод: | 2BM18040 |
| Деталь: | PLATE CONTACT MCH |
| Парткод: | 2BM18190 |
| Деталь: | CONN.CORD OD SENSOR ASSY |
| Парткод: | 2BM27290 |
| Деталь: | WIRE,DRUM UNIT |
| Парткод: | 2A627770 |
| Деталь: | OD SENSOR |
| Парткод: | 2BM26120 |
| Деталь: | GEAR Z14HZ28H DRUM |
| Парткод: | 2BM19010 |
| Деталь: | SHAFT DRUM IDLE |
| Парткод: | 2BM18180 |
| Деталь: | GEAR Z17HZ22H IDLE |
| Парткод: | 2BM18380 |
| Деталь: | GEAR Z17H CLN |
| Парткод: | 2BM18080 |
| Деталь: | ARM ROLL CLN |
| Парткод: | 2BM19100 |
| Деталь: | SHAFT ROLL CLN R |
| Парткод: | 2BM18120 |
| Деталь: | SHUTTER DRUM |
| Парткод: | 2BM18210 |
| Деталь: | SPRING SHUTTER |
| Парткод: | 2BM18240 |
| Деталь: | PLATE MCH U |
| Парткод: | 2BM18170 |
| Деталь: | COVER DRUM PWB |
| Парткод: | 2BM18340 |
| Деталь: | BUSH ROLL CLN |
| Парткод: | 2BM18090 |
| Деталь: | ROLL CLN |
| Парткод: | 2BM18060 |
| Деталь: | BRAKE DRUM ASSY |
| Парткод: | 2BM00980 |
| Деталь: | SCREW DRUM |
| Парткод: | 2BM18070 |
| Деталь: | SEAL SCREW DRUM |
| Парткод: | 2BM18460 |
| Деталь: | SEPARATOR DRUM |
| Парткод: | 2BM18330 |
| Деталь: | HOLDER SEPARATOR |
| Парткод: | 2BM18320 |
| Деталь: | LED ASSY |
| Парткод: | 2BM27300 |
| Деталь: | FRAME DRUM |
| Парткод: | 2BM18010 |
| Деталь: | SHAFT ROLL CLN F |
| Парткод: | 2BM18110 |
| Деталь: | GEAR Z16S CLN |
| Парткод: | 2BM18140 |
| Деталь: | BUSH SCREW |
| Парткод: | 2BM18150 |
| Деталь: | GEAR Z18S SCREW |
| Парткод: | 2BM18130 |
| Деталь: | SPACER DRUM SHAFT |
| Парткод: | 2BM19110 |
| Деталь: | BEARING 6901ZZNR |
| Парткод: | G3169010 |
| Деталь: | COVER DRUM F |
| Парткод: | 2BM18030 |
| Деталь: | SEAL PROTECT MCH |
| Парткод: | 2BM19120 |
| Деталь: | STAY DRUM FRAME |
| Парткод: | 2BM18200 |
| Деталь: | PLATE UNIT MOUNT |
| Парткод: | 2BM18280 |
| Деталь: | BKT CONT MCH |
| Парткод: | 2BM19020 |
| Деталь: | PLATE CONT MCH L |
| Парткод: | 2BM19040 |
| Деталь: | PLATE CONT MCH R |
| Парткод: | 2BM19030 |
| Деталь: | SPRING CONT MCH |
| Парткод: | 2BM19050 |
| Деталь: | COVER DRUM UP |
| Парткод: | 2BM18050 |
| Деталь: | HANDLE |
| Парткод: | 2BM18470 |
| Деталь: | BLADE ASSY |
| Парткод: | 2BM68260 |
| Деталь: | STUD SCREW |
| Парткод: | 2BM42640 |
| Деталь: | MC-800 MAIN CHARGER ASSY |
| Парткод: | 5PLPXAQAPKX |
| Деталь: | LEFT FRONT HOLDER,HANDLE |
| Парткод: | 2A602110 |
| Деталь: | LEFT REAR HOLDER,HANDLE |
| Парткод: | 2A602120 |
| Деталь: | LEFT REAR MOUNT,HOLDER |
| Парткод: | 2A602160 |
| Деталь: | SHAFT,HANDLE |
| Парткод: | 2AV02170 |
| Деталь: | LEFT STAY |
| Парткод: | 2A602010 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | 66321360 |
| Деталь: | LOWER RIGHT STAY |
| Парткод: | 2A602020 |
| Деталь: | RIGHT REAR MOUNT,HOLDER |
| Парткод: | 2A602150 |
| Деталь: | REAR STAY |
| Парткод: | 2A602040 |
| Деталь: | PIN,SCANNER POSITIONING |
| Парткод: | 2A612360 |
| Деталь: | UPPER RIGHT STAY |
| Парткод: | 2A602030 |
| Деталь: | HUMIDITY SENSOR |
| Парткод: | 2BM27890 |
| Деталь: | WIRE,MACHINE INSIDE SENSOR |
| Парткод: | 2A627840 |
| Деталь: | FAN UNIT |
| Парткод: | 2BM00900 |
| Деталь: | COVER OZONE ASSY |
| Парткод: | 2BM68220 |
| Деталь: | SEALOZONA |
| Парткод: | 2BM42050 |
| Деталь: | SEAL OZON B |
| Парткод: | 2BM42060 |
| Деталь: | COVER OZON |
| Парткод: | 2BM02470 |
| Деталь: | LUTCH |
| Парткод: | 2BM02460 |
| Деталь: | FAN MOTOR |
| Парткод: | 2BM42200 |
| Деталь: | FILTER KIT |
| Парткод: | 2BM42790 |
| Деталь: | HOLDER OF |
| Парткод: | 2BM02450 |
| Деталь: | DACT FAN |
| Парткод: | 2BM23010 |
| Деталь: | TUBE TONER D4 ASSY |
| Парткод: | 2BM00940 |
| Деталь: | LOWER GRAND PLATE,SCANNER |
| Парткод: | 2A626150 |
| Деталь: | SCREW FAN BELT |
| Парткод: | 2BM17960 |
| Деталь: | FRAME PROCESS ASSY |
| Парткод: | 2BM00210 |
| Деталь: | STAY PROCESS BASE |
| Парткод: | 2BM08530 |
| Деталь: | FRAME FRONT PROCESS |
| Парткод: | 2BM08510 |
| Деталь: | FRAME REAR PROCESS |
| Парткод: | 2BM08520 |
| Деталь: | PIN REAR PROCESS |
| Парткод: | 2BM08560 |
| Деталь: | STAY ACCURIDE PRO R |
| Парткод: | 2BM08540 |
| Деталь: | LABEL CLEANER |
| Парткод: | 2BM05220 |
| Деталь: | PLATE LOCK L |
| Парткод: | 2BM02980 |
| Деталь: | PLATE LOCK R |
| Парткод: | 2BM02990 |
| Деталь: | LOCK MCH |
| Парткод: | 2BM08570 |
| Деталь: | TP SCREW |
| Парткод: | 5MMT273SZ004 |
| Деталь: | SPRING LOCK MCH |
| Парткод: | 2BM08580 |
| Деталь: | LOCK PROCESS |
| Парткод: | 2BM08590 |
| Деталь: | LOCK PROCESS R |
| Парткод: | 2BM42430 |
| Деталь: | PRESS ARM D4 |
| Парткод: | 2BM08610 |
| Деталь: | SPRING D4 PROCESS |
| Парткод: | 2BM08620 |
| Деталь: | COVER BOTTOM PROCESS |
| Парткод: | 2BM08550 |
| Деталь: | SCREW PROCESS |
| Парткод: | 2BM02840 |
| Деталь: | SPRING FRAME PRO |
| Парткод: | 2BM42660 |
| Деталь: | COVER LEFT PROCESS |
| Парткод: | 2BM02830 |
| Деталь: | SHAFT BELT R |
| Парткод: | 2BM17590 |
| Деталь: | RIB BELT |
| Парткод: | 2BM17650 |
| Деталь: | SEAL PLATE BELT |
| Парткод: | 2BM43200 |
| Деталь: | SEAL MASK BELT |
| Парткод: | 2BM17980 |
| Деталь: | PULLEY BELT |
| Парткод: | 2BM17550 |
| Деталь: | PLATE BELT |
| Парткод: | 2BM17530 |
| Деталь: | GEAR Z22S |
| Парткод: | 2BM17570 |
| Деталь: | PULLEY TENSION BELT |
| Парткод: | 2BM17630 |
| Деталь: | SHAFT TENSION BELT |
| Парткод: | 2BM17640 |
| Деталь: | METAL BUSH TRANS |
| Парткод: | 2BM43080 |
| Деталь: | SHAFT BELT L |
| Парткод: | 2BM17560 |
| Деталь: | BELT TRANS |
| Парткод: | 2BM17540 |
| Деталь: | SHAFT FRONT LEVER |
| Парткод: | 2BM17040 |
| Деталь: | TR-800S SEC TRANSFER UNIT |
| Парткод: | 5PLPXATAPKX |
| Деталь: | PLATE EARTH WIRE F |
| Парткод: | 2BM17750 |
| Деталь: | WIRE EARTH GUIDE |
| Парткод: | 2BM43090 |
| Деталь: | LEVER TRANS F |
| Парткод: | 2BM17720 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 2BM17700 |
| Деталь: | CASE TRANS |
| Парткод: | 2BM17690 |
| Деталь: | SPRING CASE UP |
| Парткод: | 2BM43230 |
| Деталь: | PLATE CONTACT TC |
| Парткод: | 2BM17780 |
| Деталь: | Guide Chute Low |
| Парткод: | 2BM17710 |
| Деталь: | LEVER TRANS B |
| Парткод: | 2BM17740 |
| Деталь: | LEVER TRANS R |
| Парткод: | 2BM17730 |
| Деталь: | SPRING TC |
| Парткод: | 2BM17790 |
| Деталь: | MK-800D (SC-800 SEPARATE CHARGER) |
| Парткод: | 5PLPXBRAPKX |
| Деталь: | SC-800 SEPARATE CHARGER |
| Парткод: | 5PLPXBHAPKX |
| Деталь: | ROLLER REGIST UP |
| Парткод: | 2BM17400 |
| Деталь: | BUSH POM |
| Парткод: | 5MVM122DB003 |
| Деталь: | METAL BUSH KD |
| Парткод: | 5MMM176CJ003 |
| Деталь: | LABEL,HIGH TEMPERATURE CAUTION(EXP) |
| Парткод: | 2AB05070 |
| Деталь: | CAUTION LABEL,HIGH TEMPERATURE(JPN) |
| Парткод: | 68305100 |
| Деталь: | MOUNT, CONVEYING HEATER |
| Парткод: | 2A617010 |
| Деталь: | HEATER,CONVEYING |
| Парткод: | 2A627850 |
| Деталь: | SCREW FEED UNIT |
| Парткод: | 2BM02920 |
| Деталь: | SET PARTS KEYCOUNTER NEW COLOR |
| Парткод: | 2A369703 |
| Деталь: | SOCKET ASSY,KEY COUNTER |
| Парткод: | 41529210 |
| Деталь: | PLUG EL 4PELP-04V |
| Парткод: | J0220040 |
| Деталь: | SOCKET,KEY COUNTER |
| Парткод: | 41525016 |
| Деталь: | RETAINER,KEY COUNTER COVER |
| Парткод: | 66060022 |
| Деталь: | RETAINER,KEY COUNTER |
| Парткод: | 66060030 |
| Деталь: | MOUNT,KEY COUNTER |
| Парткод: | 66060040 |
| Деталь: | COUNTER-SUNK HEAD SCREW BFHM3X6 (BLACK) |
| Парткод: | B2303060 |
| Деталь: | BINDING SCREW BVM4X30 (BLACK) |
| Парткод: | B1304300 |
| Деталь: | TRIPLE SCREW M4X6 (BLACK) |
| Парткод: | B4304060 |
| Деталь: | TRIPLE SCREW M4X10 (BLACK) |
| Парткод: | B4304100 |
| Деталь: | BINDING SCREW BVM3X8 (BLACK) |
| Парткод: | B1303080 |
| Деталь: | TRIPLE SCREW M4X6(CHROMIUM) |
| Парткод: | B4104060 |
| Деталь: | TRIPLE SCREW M4X20(BLACK) |
| Парткод: | B4304200 |
| Деталь: | NUT BNM3 (BLACK) |
| Парткод: | C2303000 |
| Деталь: | COVER,KEY COUNTER |
| Парткод: | 2A360010 |
| Деталь: | KEY COUNTER |
| Парткод: | 82142540 |
| Деталь: | TB-82(TONER BOTTLE) |
| Парткод: | 2BM93190 |
| Деталь: | STAY,DESK BASE |
| Парткод: | 2A660940 |
| Деталь: | COVER,DESK STAY |
| Парткод: | 2A660950 |
| Деталь: | CASTER,MACHINE |
| Парткод: | 36502600 |
| Деталь: | BOLT,LEVEL |
| Парткод: | 66502120 |
| Деталь: | BINDING SCREW WITH SW (BLACK)M4X8 |
| Парткод: | B1324120 |
| Деталь: | TRIPLE SCREW M4X08(CHROMIUM) |
| Парткод: | B4104080 |
| Деталь: | LABEL,STOPPER |
| Парткод: | 3AT05070 |
| Деталь: | DR-800A(DRIVE UNIT A) |
| Парткод: | 2BM93040 |
| Деталь: | MOTOR MAIN |
| Парткод: | 2BM27690 |
| Деталь: | HOLDER ASSYB |
| Парткод: | 2BM22200 |
| Деталь: | PLATE DRIVE MAIN B |
| Парткод: | 2BM22020 |
| Деталь: | GEAR Z144H |
| Парткод: | 2BM22050 |
| Деталь: | MOTOR DLP |
| Парткод: | 2BM27700 |
| Деталь: | GEAR Z36H Z117H |
| Парткод: | 2BM22060 |
| Деталь: | BUSH 6-9-4 |
| Парткод: | 2BM22360 |
| Деталь: | EDGING,EDS-0607U(KITAGAWA) |
| Парткод: | M2104260 |
| Деталь: | GEAR Z30 Z58H ASSY |
| Парткод: | 2BM22070 |
| Деталь: | GEAR Z25 Z29 |
| Парткод: | 2BM22090 |
| Деталь: | GEAR Z23 IDLE |
| Парткод: | 2BM22170 |
| Деталь: | GEAR Z29 IDLE |
| Парткод: | 2BM22100 |
| Деталь: | GEAR Z14 Z29 |
| Парткод: | 2BM22160 |
| Деталь: | GEAR Z43H |
| Парткод: | 2BM22140 |
| Деталь: | GEAR Z30 Z57H ASSY |
| Парткод: | 2BM22080 |
| Деталь: | GEAR Z53 |
| Парткод: | 2BM23760 |
| Деталь: | PLATE DEIVE MAIN C |
| Парткод: | 2BM22030 |
| Деталь: | GEAR Z26 IDLE |
| Парткод: | 2BM22110 |
| Деталь: | GEAR Z34 |
| Парткод: | 2BM23750 |
| Деталь: | BEARING,REGISTRATION FULCRUM |
| Парткод: | 34922480 |
| Деталь: | GEAR Z30 JOINT MIX |
| Парткод: | 2BM22130 |
| Деталь: | BUSH MAIN C |
| Парткод: | 2BM23800 |
| Деталь: | GEAR Z21H Z26 |
| Парткод: | 2BM22150 |
| Деталь: | GEAR Z28 |
| Парткод: | 2BM22180 |
| Деталь: | CLUTCH ASSY 2 |
| Парткод: | 2BM23720 |
| Деталь: | SPRING HV |
| Парткод: | 2BM23780 |
| Деталь: | HOLDER ASSY CHY |
| Парткод: | 2BM22220 |
| Деталь: | HOLDER ASSY CHM |
| Парткод: | 2BM22230 |
| Деталь: | HOLDER ASSY CHC |
| Парткод: | 2BM22240 |
| Деталь: | HOLDER ASSY CHK |
| Парткод: | 2BM22250 |
| Деталь: | PLATE DRIVE MAIN A |
| Парткод: | 2BM22010 |
| Деталь: | BUSH CL CAM |
| Парткод: | 2BM22270 |
| Деталь: | SHAFT JOINT CAM |
| Парткод: | 2BM22420 |
| Деталь: | CLUTCH ASSY CAM |
| Парткод: | 2BM22280 |
| Деталь: | SHAFT JOINT SCREW |
| Парткод: | 2BM22430 |
| Деталь: | CLUTCH 26-C |
| Парткод: | 2BM27630 |
| Деталь: | HOUSING CL CAM |
| Парткод: | 2BM22260 |
| Деталь: | SPRING JOINT CAM |
| Парткод: | 2BM22460 |
| Деталь: | JOINT CAM |
| Парткод: | 2BM22330 |
| Деталь: | JOINT ROLL SCREW |
| Парткод: | 2BM22320 |
| Деталь: | ACUTUATER CAM |
| Парткод: | 2BM22350 |
| Деталь: | SPRING ACUTUATOR |
| Парткод: | 2BM22470 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | SOLENOID CAM |
| Парткод: | 2BM27640 |
| Деталь: | PLATE SENSOR |
| Парткод: | 2BM22380 |
| Деталь: | SHAFT JOINT DRUM |
| Парткод: | 2BM22400 |
| Деталь: | HOLDERASSYA |
| Парткод: | 2BM22190 |
| Деталь: | SPRING JOINT DRUM |
| Парткод: | 2BM22450 |
| Деталь: | JOINT DRUM |
| Парткод: | 2BM23830 |
| Деталь: | P.W.BOARD KP-824 ASSY |
| Парткод: | 2BM01170 |
| Деталь: | LID HV UNIT |
| Парткод: | 2BM22500 |
| Деталь: | EARTH DLP |
| Парткод: | 2BM22510 |
| Деталь: | PLATE HV JOINT |
| Парткод: | 2BM22530 |
| Деталь: | EARTH DRUM |
| Парткод: | 2BM22520 |
| Деталь: | PLATE HV DRUM |
| Парткод: | 2BM22540 |
| Деталь: | EARTH DRUM T1 |
| Парткод: | 2BM23810 |
| Деталь: | METAL BUSH KD |
| Парткод: | 5MMM176C003 |
| Деталь: | CASE HV JOINT DLP |
| Парткод: | 2BM22490 |
| Деталь: | HOLDER HARNESS D |
| Парткод: | 2BM23730 |
| Деталь: | SOLENOID Y |
| Парткод: | 2BM27650 |
| Деталь: | PLATE SOLENOID |
| Парткод: | 2BM22370 |
| Деталь: | LEVER SOLENOID |
| Парткод: | 2BM22340 |
| Деталь: | SPRING LEVER |
| Парткод: | 2BM22440 |
| Деталь: | SEAL SOLENOID |
| Парткод: | 2BM22480 |
| Деталь: | SOLENOID M |
| Парткод: | 2BM27660 |
| Деталь: | SOLENOID C |
| Парткод: | 2BM27670 |
| Деталь: | SOLENOID K |
| Парткод: | 2BM27680 |
| Деталь: | PLATE DRIVE MAIN D |
| Парткод: | 2BM22040 |
| Деталь: | SHAFT JOINT MIX ASSY |
| Парткод: | 2BM68230 |
| Деталь: | JOINT MIX |
| Парткод: | 2BM23820 |
| Деталь: | SPRING JOINT MIX |
| Парткод: | 2BM23660 |
| Деталь: | HOUSING JOINT ASSY |
| Парткод: | 2BM23770 |
| Деталь: | SHAFT JOINT MIX |
| Парткод: | 2BM22410 |
| Деталь: | PARTS,DEVELOPING UNIT (BK) |
| Парткод: | 2A693150 |
| Деталь: | CASE DLP D4 |
| Парткод: | 2BM15440 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 2BM27540 |
| Деталь: | SENSOR FACE D1234 |
| Парткод: | 2BM14310 |
| Деталь: | MAGNET SEAL D1234 |
| Парткод: | 2BM40560 |
| Деталь: | SEAL SIDE D24 |
| Парткод: | 2BM40570 |
| Деталь: | SCRAPER PULLEY D1234 |
| Парткод: | 2BM14300 |
| Деталь: | MAGNET MIXER D1234 |
| Парткод: | 2BM14180 |
| Деталь: | SEAL CASE B D4 |
| Парткод: | 2BM15810 |
| Деталь: | SEAL CASE D123 |
| Парткод: | 2BM14500 |
| Деталь: | SEAL BUSH D1234 |
| Парткод: | 2BM40190 |
| Деталь: | SPACER D1234 |
| Парткод: | 2BM40200 |
| Деталь: | OIL SEAL |
| Парткод: | 2BM14390 |
| Деталь: | BUSH D1234 |
| Парткод: | 2BM14330 |
| Деталь: | SCRAPER HOPPER D4 |
| Парткод: | 2BM15510 |
| Деталь: | SHEET SCRAPER D4 |
| Парткод: | 2BM15880 |
| Деталь: | SP SENSOR D4 |
| Парткод: | 2BM15580 |
| Деталь: | GEAR Z28-5 D1234 |
| Парткод: | 2BM14210 |
| Деталь: | ROLL SUPPLY |
| Парткод: | 2BM15870 |
| Деталь: | GEAR SUPPLY |
| Парткод: | 2BM15860 |
| Деталь: | TONER EMPTY DETECTION SENSOR |
| Парткод: | 33915180 |
| Деталь: | CONN.CORD SENSOR D4 ASSY |
| Парткод: | 2BM27590 |
| Деталь: | COVER BOTTOM D4 |
| Парткод: | 2BM15540 |
| Деталь: | SEAL BOTTOM B D4 |
| Парткод: | 2BM15820 |
| Деталь: | SEAL BOTTOM A D4 |
| Парткод: | 2BM15830 |
| Деталь: | BKT MOTOR TONER D4 |
| Парткод: | 2BM15550 |
| Деталь: | DC motor |
| Парткод: | 2BM27340 |
| Деталь: | GP MOTOR GEAR |
| Парткод: | 2BM15850 |
| Деталь: | CONN.CORD TM D4 ASSY |
| Парткод: | 2BM27600 |
| Деталь: | GEAR Z35-Z17-5 D4 |
| Парткод: | 2BM15690 |
| Деталь: | TUBE MIXER D1234 |
| Парткод: | 2BM14130 |
| Деталь: | FLANGE MIXER L D1234 |
| Парткод: | 2BM14150 |
| Деталь: | SCREW MIXER D1234 |
| Парткод: | 2BM14160 |
| Деталь: | SHAFT MIXER D4 |
| Парткод: | 2BM40110 |
| Деталь: | FLANGE MIXER R D1234 |
| Парткод: | 2BM14170 |
| Деталь: | SCRAPER MIXER D1234 |
| Парткод: | 2BM40580 |
| Деталь: | GEAR Z35-5T D4 |
| Парткод: | 2BM15680 |
| Деталь: | ROLL MAG2 D4 |
| Парткод: | 2BM40530 |
| Деталь: | FLANGE BUSH D4 |
| Парткод: | 2BM15770 |
| Деталь: | SEAL FLANGE D4 |
| Парткод: | 2BM15840 |
| Деталь: | BEARING R-1560X2DD |
| Парткод: | G4090010 |
| Деталь: | GEAR Z24-5 D4 |
| Парткод: | 2BM15760 |
| Деталь: | BALL BEARING D1234 |
| Парткод: | 2BM40310 |
| Деталь: | GEAR Z18-8 D4 |
| Парткод: | 2BM15740 |
| Деталь: | STAY DLP D4 |
| Парткод: | 2BM15450 |
| Деталь: | SEAL BLADE D1234 |
| Парткод: | 2BM14320 |
| Деталь: | SEAL CASE A D4 |
| Парткод: | 2BM40010 |
| Деталь: | GEAR Z22-Z20 D4 |
| Парткод: | 2BM15710 |
| Деталь: | PLATE GEAR D4 |
| Парткод: | 2BM15620 |
| Деталь: | GEAR Z15-8 D4 |
| Парткод: | 2BM15430 |
| Деталь: | GEAR Z20-Z16 D4 |
| Парткод: | 2BM40680 |
| Деталь: | GEAR Z17-8 D4 |
| Парткод: | 2BM40690 |
| Деталь: | GEAR Z24-8 D4 |
| Парткод: | 2BM15730 |
| Деталь: | ROLLER MAGNET D4 |
| Парткод: | 2BM14620 |
| Деталь: | PULLY D1234 |
| Парткод: | 2BM14010 |
| Деталь: | GAER MG H D1234 |
| Парткод: | 2BM40460 |
| Деталь: | FLANGE R D4 |
| Парткод: | 2BM15490 |
| Деталь: | GEAR Z20-5 D1234 |
| Парткод: | 2BM14110 |
| Деталь: | GEAR Z25-5 D34 |
| Парткод: | 2BM15100 |
| Деталь: | GEAR Z43-Z17-5 D4 |
| Парткод: | 2BM15700 |
| Деталь: | BKT CONNECTOR D4 |
| Парткод: | 2BM15530 |
| Деталь: | PLATE GEAR MAG2 D4 |
| Парткод: | 2BM40090 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | ROLLER BLADE D1234 |
| Парткод: | 2BM14030 |
| Деталь: | PITCH PIECE F D4 |
| Парткод: | 2BM15470 |
| Деталь: | PLATE IDLE D4 |
| Парткод: | 2BM15790 |
| Деталь: | PLATE JOINT BIAS D4 |
| Парткод: | 2BM15610 |
| Деталь: | SHAFT MG BLADE D1234 |
| Парткод: | 2BM14040 |
| Деталь: | BUSH BIAS D1234 |
| Парткод: | 2BM14220 |
| Деталь: | SP MG BLADE D1234 |
| Парткод: | 2BM14290 |
| Деталь: | JOINT MG D1234 |
| Парткод: | 2BM14050 |
| Деталь: | PLATE ANGLE D4 |
| Парткод: | 2BM15570 |
| Деталь: | PRESSDCUT D1234 |
| Парткод: | 2BM40040 |
| Деталь: | GEAR Z39H D4 |
| Парткод: | 2BM40450 |
| Деталь: | BKT CLUTCH D4 |
| Парткод: | 2BM15480 |
| Деталь: | GEAR Z30H-Z22H D34 |
| Парткод: | 2BM40650 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | CLUTCH 26-H |
| Парткод: | 2BM27960 |
| Деталь: | SEAL CLUTH D1234 |
| Парткод: | 2BM40150 |
| Деталь: | SHAFT CLUTCH D1234 |
| Парткод: | 2BM14070 |
| Деталь: | JOINT D1234 |
| Парткод: | 2BM14090 |
| Деталь: | POLY WASHER 16 |
| Парткод: | 2BM40500 |
| Деталь: | POLY WASHER 14 |
| Парткод: | 2BM40510 |
| Деталь: | GEAR Z14D-8 D1234 |
| Парткод: | 2BM40360 |
| Деталь: | GEAR Z14-Z12 D4 |
| Парткод: | 2BM40670 |
| Деталь: | GEAR Z24-Z18-8 D4 |
| Парткод: | 2BM15750 |
| Деталь: | PITCH PIECE R D4 |
| Парткод: | 2BM15500 |
| Деталь: | COVER F D4 |
| Парткод: | 2BM15650 |
| Деталь: | SEAL MG D1234 |
| Парткод: | 2BM40300 |
| Деталь: | COVER MAG D4 |
| Парткод: | 2BM15520 |
| Деталь: | SEAL COVER MG D4 |
| Парткод: | 2BM40520 |
| Деталь: | WIRE K,DEVELOPING |
| Парткод: | 2A627590 |
| Деталь: | SIMM D1234 |
| Парткод: | 2BM40700 |
| Деталь: | COVER PWB D234 |
| Парткод: | 2BM14870 |
| Деталь: | COVER R D4 |
| Парткод: | 2BM15560 |
| Деталь: | SEAL SHUTTER D4 |
| Парткод: | 2BM15590 |
| Деталь: | PRESS PIECE D4 |
| Парткод: | 2BM15600 |
| Деталь: | SP PRESS D4 |
| Парткод: | 2BM15670 |
| Деталь: | COVER MOTOR D4 |
| Парткод: | 2BM15630 |
| Деталь: | SEAL LID DEVE D1234 |
| Парткод: | 2BM14270 |
| Деталь: | SHEET PWB D1234 |
| Парткод: | 2BM40140 |
| Деталь: | SHUTTER D4 |
| Парткод: | 2BM15640 |
| Деталь: | SP SHUTTER D4 |
| Парткод: | 2BM15800 |
| Деталь: | COVER HOPPER D4 |
| Парткод: | 2BM15660 |
| Деталь: | SEAL COVER HOPPER D4 |
| Парткод: | 2BM15780 |
| Деталь: | COVER TOP FUSER |
| Парткод: | 2BM20580 |
| Деталь: | SPRING EXIT |
| Парткод: | 2BM20790 |
| Деталь: | Bush SP |
| Парткод: | 2BM20610 |
| Деталь: | SHAFT EXIT |
| Парткод: | 5MMT622SN003 |
| Деталь: | PULLEY EXIT |
| Парткод: | 5MVM176DB018 |
| Деталь: | PUSH OIL |
| Парткод: | 2BM20720 |
| Деталь: | SPRING LOCK OIL |
| Парткод: | 2BM20780 |
| Деталь: | LEVER OIL F |
| Парткод: | 2BM20730 |
| Деталь: | LOCK COVER TOP F |
| Парткод: | 2BM20700 |
| Деталь: | Spring Lock F |
| Парткод: | 2BM20810 |
| Деталь: | BKT COVER TOP F |
| Парткод: | 2BM20670 |
| Деталь: | BUSHING POM |
| Парткод: | 5MVM176DB006 |
| Деталь: | MECH CLUTCH OIL |
| Парткод: | 2BM20650 |
| Деталь: | BUSH MIXER GEAR |
| Парткод: | 5MVM166DN004 |
| Деталь: | COVER EXIT FUSER |
| Парткод: | 2BM20390 |
| Деталь: | GUIDE EXIT LOW |
| Парткод: | 2BM20350 |
| Деталь: | NUT FUSER |
| Парткод: | 5MMK116SZ001 |
| Деталь: | SPRING PRESSURE |
| Парткод: | 2BM20180 |
| Деталь: | BUSH SWEEP F |
| Парткод: | 2BM16880 |
| Деталь: | BUSH SCREW F |
| Парткод: | 2BM16700 |
| Деталь: | GEAR SCREW Z19 |
| Парткод: | 2BM16860 |
| Деталь: | COVER CLEANER F |
| Парткод: | 2BM16620 |
| Деталь: | PLATE GUIDE SWEEP |
| Парткод: | 2BM16980 |
| Деталь: | SEAL GUIDE SWEEP |
| Парткод: | 2BM16970 |
| Деталь: | PUSH NUT |
| Парткод: | 2BM45020 |
| Деталь: | SEAL BRUSH SIDE R |
| Парткод: | 2BM16820 |
| Деталь: | JOINT SCREW |
| Парткод: | 2BM16660 |
| Деталь: | PARTS,DEVELOPING UNIT (M),(USA) |
| Парткод: | 2A693110 |
| Деталь: | PARTS,DEVELOPING UNIT (m),(j/E) |
| Парткод: | 2A693120 |
| Деталь: | CASE DLP D2 |
| Парткод: | 2BM14950 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 2BM27330 |
| Деталь: | SENSOR FACE D1234 |
| Парткод: | 2BM14310 |
| Деталь: | SEAL SIDE D24 |
| Парткод: | 2BM40570 |
| Деталь: | MAGNET SEAL D1234 |
| Парткод: | 2BM40560 |
| Деталь: | SEAL CASE D D2 |
| Парткод: | 2BM15070 |
| Деталь: | SCRAPER PULLEY D1234 |
| Парткод: | 2BM14300 |
| Деталь: | MAGNET MIXER D1234 |
| Парткод: | 2BM14180 |
| Деталь: | SEAL BUSH D1234 |
| Парткод: | 2BM40190 |
| Деталь: | SPACER D1234 |
| Парткод: | 2BM40200 |
| Деталь: | OIL SEAL |
| Парткод: | 2BM14390 |
| Деталь: | BUSH D1234 |
| Парткод: | 2BM14330 |
| Деталь: | SHAFT T BRAKE D12 |
| Парткод: | 2BM14580 |
| Деталь: | GEAR Z28-5 D1234 |
| Парткод: | 2BM14210 |
| Деталь: | SHAFT CROSS D2 ASSY |
| Парткод: | 2BM00780 |
| Деталь: | SHAFT GEAR MIX 1 |
| Парткод: | 2BM40230 |
| Деталь: | GEAR Z28-5 MIX2 |
| Парткод: | 2BM40220 |
| Деталь: | GEAR MIXER 1 D123 |
| Парткод: | 2BM14410 |
| Деталь: | TUBE MIXER D1234 |
| Парткод: | 2BM14130 |
| Деталь: | FLANGE MIXER L D1234 |
| Парткод: | 2BM14150 |
| Деталь: | SCREW MIXER D1234 |
| Парткод: | 2BM14160 |
| Деталь: | SHAFT MIXER D123 |
| Парткод: | 2BM40100 |
| Деталь: | FLANGE MIXER R D1234 |
| Парткод: | 2BM14170 |
| Деталь: | SCRAPER MIXER D1234 |
| Парткод: | 2BM40580 |
| Деталь: | GEAR MIXER 2 D123 |
| Парткод: | 2BM14420 |
| Деталь: | STAY D2 |
| Парткод: | 2BM14960 |
| Деталь: | SEAL CASE E D2 |
| Парткод: | 2BM15080 |
| Деталь: | SEAL BLADE D1234 |
| Парткод: | 2BM14320 |
| Деталь: | SEAL CASE A D2 |
| Парткод: | 2BM40130 |
| Деталь: | SEAL CASE D12 |
| Парткод: | 2BM14610 |
| Деталь: | SEAL CASE B D2 |
| Парткод: | 2BM15060 |
| Деталь: | SEAL CASE D123 |
| Парткод: | 2BM14500 |
| Деталь: | ROLLER MAGNET D23 |
| Парткод: | 2BM14940 |
| Деталь: | PULLY D1234 |
| Парткод: | 2BM14010 |
| Деталь: | GAER MG H D1234 |
| Парткод: | 2BM40460 |
| Деталь: | FLANGE R D2 |
| Парткод: | 2BM14970 |
| Деталь: | GEAR Z30-Z16 D12 |
| Парткод: | 2BM14590 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | ROLLER BLADE D1234 |
| Парткод: | 2BM14030 |
| Деталь: | SHAFT MG BLADE D1234 |
| Парткод: | 2BM14040 |
| Деталь: | BUSH BIAS D1234 |
| Парткод: | 2BM14220 |
| Деталь: | SP MG BLADE D1234 |
| Парткод: | 2BM14290 |
| Деталь: | JOINT MG D1234 |
| Парткод: | 2BM14050 |
| Деталь: | GAER Z20H D12 |
| Парткод: | 2BM40420 |
| Деталь: | GAER Z20H R D12 |
| Парткод: | 2BM40430 |
| Деталь: | PITCH PIECE R D2 |
| Парткод: | 2BM14980 |
| Деталь: | PITCH PIECE F D2 |
| Парткод: | 2BM15010 |
| Деталь: | BIAS JOINT D123 |
| Парткод: | 2BM14400 |
| Деталь: | PLATE ANGLE D123 |
| Парткод: | 2BM14440 |
| Деталь: | PRESSDCUT D1234 |
| Парткод: | 2BM40040 |
| Деталь: | PLATE IDLE D23 |
| Парткод: | 2BM14930 |
| Деталь: | GEAR Z20-5 D1234 |
| Парткод: | 2BM14110 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | GEAR Z38-5 D23 |
| Парткод: | 2BM14910 |
| Деталь: | COVER F D2 |
| Парткод: | 2BM15050 |
| Деталь: | SEAL MG D1234 |
| Парткод: | 2BM40300 |
| Деталь: | BKT CLUTCH D2 |
| Парткод: | 2BM14990 |
| Деталь: | GEAR Z30H-Z22H D12 |
| Парткод: | 2BM40640 |
| Деталь: | CLUTCH 26-E |
| Парткод: | 2BM27420 |
| Деталь: | SEAL CLUTH D1234 |
| Парткод: | 2BM40150 |
| Деталь: | SHAFT CLUTCH D1234 |
| Парткод: | 2BM14070 |
| Деталь: | JOINT D1234 |
| Парткод: | 2BM14090 |
| Деталь: | POLY WASHER 16 |
| Парткод: | 2BM40500 |
| Деталь: | BALL BEARING D1234 |
| Парткод: | 2BM40310 |
| Деталь: | POLY WASHER 14 |
| Парткод: | 2BM40510 |
| Деталь: | GEAR Z14D-8 D1234 |
| Парткод: | 2BM40360 |
| Деталь: | GEAR Z15-8 D123 |
| Парткод: | 2BM40370 |
| Деталь: | GEAR Z14-Z12 D123 |
| Парткод: | 2BM40590 |
| Деталь: | SHAFT GEAR D12 |
| Парткод: | 2BM14570 |
| Деталь: | Bush |
| Парткод: | 2BM14530 |
| Деталь: | GEAR Z14-8 JOINT D12 |
| Парткод: | 2BM14560 |
| Деталь: | GUIDE TCNT D2 |
| Парткод: | 2BM15000 |
| Деталь: | GUIDE SHUTTER D1234 |
| Парткод: | 2BM14200 |
| Деталь: | SEAL GUIDE T D1234 |
| Парткод: | 2BM14260 |
| Деталь: | SEAL SHUTTER D1234 |
| Парткод: | 2BM14250 |
| Деталь: | SHUTTER D1234 |
| Парткод: | 2BM14240 |
| Деталь: | SPRING SHUTTER D1234 |
| Парткод: | 2BM14230 |
| Деталь: | LOCK SHUTTER D1234 |
| Парткод: | 2BM14120 |
| Деталь: | PW.BOARD KP-819 ASSY |
| Парткод: | 2BM01140 |
| Деталь: | CONN.CORD LED D2 ASSY |
| Парткод: | 2BM27440 |
| Деталь: | GUIDE SCREW D23 |
| Парткод: | 2BM14890 |
| Деталь: | WIRE M,DEVELOPING |
| Парткод: | 2A627620 |
| Деталь: | GEAR Z20-8 D12 |
| Парткод: | 2BM14600 |
| Деталь: | PLATE MOTOR TONER D2 |
| Парткод: | 2BM15020 |
| Деталь: | GEAR Z31-Z15-8 D123 |
| Парткод: | 2BM14460 |
| Деталь: | SP JOINT T SRP D23 |
| Парткод: | 2BM14920 |
| Деталь: | JOINT SCRAPER CI D |
| Парткод: | 2A614070 |
| Деталь: | GEAR Z14-8 D23 |
| Парткод: | 2BM14280 |
| Деталь: | DC motor |
| Парткод: | 2BM27340 |
| Деталь: | GEAR WORM |
| Парткод: | 2BM14540 |
| Деталь: | CONN.CORD TM D2 ASSY |
| Парткод: | 2BM27460 |
| Деталь: | JOINT FEED T D123 |
| Парткод: | 2BM14470 |
| Деталь: | SP JOINT T SW D1234 |
| Парткод: | 2BM14190 |
| Деталь: | BKT JOINT TCNT D23 |
| Парткод: | 2BM14880 |
| Деталь: | WORM WHEEL D123 |
| Парткод: | 2BM14480 |
| Деталь: | LABEL POSITION M |
| Парткод: | 2BM05190 |
| Деталь: | COVER TCNT D23 |
| Парткод: | 2BM14900 |
| Деталь: | PW.BOARD KP-820 ASSY |
| Парткод: | 2BM01150 |
| Деталь: | CONN.CORD PTR D2 ASSY |
| Парткод: | 2BM27450 |
| Деталь: | DETECTION PLATE D2,DEVELOPING(F) |
| Парткод: | 2A614030 |
| Деталь: | DETECTION PLATE D2,DEVELOPING(G) |
| Парткод: | 2A614040 |
| Деталь: | CORD PRESS D2 |
| Парткод: | 2BM15090 |
| Деталь: | SIMM D1234 |
| Парткод: | 2BM40700 |
| Деталь: | SHEET PWB D2 |
| Парткод: | 2BM40660 |
| Деталь: | COVER PWB D234 |
| Парткод: | 2BM14870 |
| Деталь: | COVER R D2 |
| Парткод: | 2BM15030 |
| Деталь: | COVER MAG D2 |
| Парткод: | 2BM15040 |
| Деталь: | SEAL COVER MAG D2 |
| Парткод: | 2BM40290 |
| Деталь: | SEAL COVER MAG D234 |
| Парткод: | 2BM40160 |
| Деталь: | SEAL LID DEVE D1234 |
| Парткод: | 2BM14270 |
| Деталь: | SHEET PWB D1234 |
| Парткод: | 2BM40140 |
| Деталь: | PARTS,MIDDLE TRANSFER UNIT |
| Парткод: | 2A693190 |
| Деталь: | COVER IMAGE R |
| Парткод: | 2BM16160 |
| Деталь: | JOINT CAM CL |
| Парткод: | 2BM16200 |
| Деталь: | PLATE BIAS FLICKER B |
| Парткод: | 2BM16460 |
| Деталь: | BUSH CYLINDER |
| Парткод: | 2BM16150 |
| Деталь: | PLATE PRESS IMAGE R |
| Парткод: | 2BM16240 |
| Деталь: | SPRING IMAGE PRESS |
| Парткод: | 2BM16320 |
| Деталь: | CAM PRESS R |
| Парткод: | 2BM16350 |
| Деталь: | SPRING PLATE IMAGE |
| Парткод: | 2BM16990 |
| Деталь: | MINIATURE BEARING 686ZZ |
| Парткод: | G3006860 |
| Деталь: | STOPPER GUIDE |
| Парткод: | 2BM16500 |
| Деталь: | PLATE IMAGE R ASSY |
| Парткод: | 2BM16370 |
| Деталь: | BUSH DRUM |
| Парткод: | 2BM21210 |
| Деталь: | HOLDER CL R |
| Парткод: | 2BM16220 |
| Деталь: | PLATE PICH IMAGE R |
| Парткод: | 2BM16400 |
| Деталь: | SCREW STUD A |
| Парткод: | 2BM16830 |
| Деталь: | SHAFT IMAGE LOCK |
| Парткод: | 2BM16330 |
| Деталь: | LOCK IMAGE |
| Парткод: | 2BM16380 |
| Деталь: | BRACKET SENSOR ID |
| Парткод: | 2BM16030 |
| Деталь: | PT.SENSOR KUA0020C |
| Парткод: | 2BM27720 |
| Деталь: | FRAME IMAGE TOP ASSY |
| Парткод: | 2BM00820 |
| Деталь: | SPRING SENSOR ID |
| Парткод: | 2BM16060 |
| Деталь: | PAD CLEANER ID |
| Парткод: | 2BM16050 |
| Деталь: | NOB CLEANER ID |
| Парткод: | 2BM16040 |
| Деталь: | STAY IMAGE |
| Парткод: | 2BM16070 |
| Деталь: | PULLEY IMAGE |
| Парткод: | 2BM16080 |
| Деталь: | BRACKET CLEANER |
| Парткод: | 2BM16260 |
| Деталь: | SEAL BKT CLEANER |
| Парткод: | 2BM16560 |
| Деталь: | SPRING PRESS CL F |
| Парткод: | 2BM16280 |
| Деталь: | LEVER CL |
| Парткод: | 2BM16440 |
| Деталь: | SHAFT LEVER |
| Парткод: | 2BM16520 |
| Деталь: | SPRING PRESS CL R |
| Парткод: | 2BM16270 |
| Деталь: | CAM CLEANER |
| Парткод: | 2BM16190 |
| Деталь: | SHAFT CAM CLEANER |
| Парткод: | 2BM16180 |
| Деталь: | PLATE PICH IMAGE F |
| Парткод: | 2BM16390 |
| Деталь: | PLATE IMAGE F ASSY |
| Парткод: | 2BM16360 |
| Деталь: | EARTH FRAME |
| Парткод: | 2BM16930 |
| Деталь: | CAM PRESS F |
| Парткод: | 2BM16340 |
| Деталь: | GEAR LEVER FRAME |
| Парткод: | 2BM16010 |
| Деталь: | PLATE PRESS IMAGE F |
| Парткод: | 2BM16230 |
| Деталь: | HOLDER CL F |
| Парткод: | 2BM16210 |
| Деталь: | LEVER CL RELEASE A |
| Парткод: | 2BM16420 |
| Деталь: | LEVER CL RELEASE B |
| Парткод: | 2BM16430 |
| Деталь: | EARTH IMAGE |
| Парткод: | 2BM16250 |
| Деталь: | STOPPER LEVER IMAGE |
| Парткод: | 2BM16300 |
| Деталь: | SPRING STOPPER LEVER |
| Парткод: | 2BM16310 |
| Деталь: | LEVER LOCK |
| Парткод: | 2BM16410 |
| Деталь: | SPRING LEVER LOCK |
| Парткод: | 2BM16920 |
| Деталь: | STOPPER SPRING |
| Парткод: | 2BM16480 |
| Деталь: | SPRING LEVER FRAME |
| Парткод: | 2BM16490 |
| Деталь: | COVER IMAGE F |
| Парткод: | 2BM16290 |
| Деталь: | LABEL IMAGE C |
| Парткод: | 2BM16550 |
| Деталь: | LEVER FRAME IMAGE |
| Парткод: | 2BM16020 |
| Деталь: | LABEL IMAGE A |
| Парткод: | 2BM16530 |
| Деталь: | LABEL IMAGE B |
| Парткод: | 2BM16540 |
| Деталь: | WIRE,IMAGE DENSITY SENSOR |
| Парткод: | 2A627560 |
| Деталь: | BC-800(BRUSH CLEANER) |
| Парткод: | 2BM93270 |
| Деталь: | BUSH SCREW R |
| Парткод: | 2BM16690 |
| Деталь: | SEAL SHIELD SCREW |
| Парткод: | 2BM16940 |
| Деталь: | SCREW CLEANER |
| Парткод: | 2BM16640 |
| Деталь: | SHAFT SCREW |
| Парткод: | 2BM16760 |
| Деталь: | COVER CLEANER R |
| Парткод: | 2BM16630 |
| Деталь: | SPRING SHUTTER |
| Парткод: | 2BM16590 |
| Деталь: | PLATE BAIS SWEEP |
| Парткод: | 2BM16870 |
| Деталь: | BUSH EARTH |
| Парткод: | 2BM16900 |
| Деталь: | SHUTTER CLEANER |
| Парткод: | 2BM16570 |
| Деталь: | BUSH BRUSH R |
| Парткод: | 2BM16670 |
| Деталь: | BUSH SWEEP R |
| Парткод: | 2BM16890 |
| Деталь: | SEAL SHUTTER |
| Парткод: | 2BM16580 |
| Деталь: | SEAL SHUTTERB |
| Парткод: | 2BM45010 |
| Деталь: | SEAL SWEEP SIDE F |
| Парткод: | 2BM16950 |
| Деталь: | FRAME CLEANER |
| Парткод: | 2BM16610 |
| Деталь: | GUIDE TONER |
| Парткод: | 2BM16740 |
| Деталь: | SEAL GUIDE TONER |
| Парткод: | 2BM16780 |
| Деталь: | BLADE CLEANER |
| Парткод: | 2BM16910 |
| Деталь: | ROLLER SWEEP |
| Парткод: | 2BM16850 |
| Деталь: | BRUSH FUR |
| Парткод: | 2BM16600 |
| Деталь: | BUSH BRUSH F |
| Парткод: | 2BM16680 |
| Деталь: | GEAR BRUSH Z19 |
| Парткод: | 2BM16730 |
| Деталь: | SEAL BRUSH SIDE F |
| Парткод: | 2BM16810 |
| Деталь: | UNIT ASSY MPF |
| Парткод: | 2A600210 |
| Деталь: | COVER RIGHT MPF ASSY |
| Парткод: | 2BM68130 |
| Деталь: | LOCK COVER MPF |
| Парткод: | 2BM07130 |
| Деталь: | SPRING LOCK MPF |
| Парткод: | 2BM07140 |
| Деталь: | TRAY EXTENTION MPF |
| Парткод: | 2BM07120 |
| Деталь: | BASE TRAY MPF |
| Парткод: | -2BM07110 |
| Деталь: | LABEL MPF |
| Парткод: | 2BM07370 |
| Деталь: | ORIGINAL SIZE INDICATOR MPF,SIZE |
| Парткод: | 2A605010 |
| Деталь: | COVER RIGHT MPF |
| Парткод: | 2BM07100 |
| Деталь: | PLATE BOTTOM MPF ASSY |
| Парткод: | 2BM68140 |
| Деталь: | PAD FRICTION |
| Парткод: | 2BM07170 |
| Деталь: | GUIDE PAPER SIDE F |
| Парткод: | 2BM07200 |
| Деталь: | GUIDE PAPER SIDE R |
| Парткод: | 2BM07180 |
| Деталь: | GEAR GUIDE SIDE |
| Парткод: | 2BM07310 |
| Деталь: | HOLDER GUIDE SIDE |
| Парткод: | 2BM07210 |
| Деталь: | PLATE BOTTOM B |
| Парткод: | 2BM07160 |
| Деталь: | PLATE BOTTOM A |
| Парткод: | 2BM07150 |
| Деталь: | GUIDE PAPER MPF |
| Парткод: | 2BM07020 |
| Деталь: | ACTUATOR CAM MPF |
| Парткод: | 2BM07050 |
| Деталь: | RETARD ROLL ASSY |
| Парткод: | 2BM07340 |
| Деталь: | P.W.BOARD KP-832 ASSY |
| Парткод: | 2BM01210 |
| Деталь: | UPPER COVER,BYPASS |
| Парткод: | 2A604110 |
| Деталь: | PLATE EARTH MPF |
| Парткод: | 2BM07070 |
| Деталь: | FRAME RIGHT MPF |
| Парткод: | 2BM07010 |
| Деталь: | LABEL MP TRAY |
| Парткод: | 2BM07360 |
| Деталь: | ACTUATOR PAPER MPF |
| Парткод: | 2BM07060 |
| Деталь: | SHAFT ROLL MPF |
| Парткод: | 2BM07260 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | BUSH POM B |
| Парткод: | 2BM07320 |
| Деталь: | ROLL FEED MPF ASSY |
| Парткод: | 2BM07270 |
| Деталь: | CLUTCH MPF ASSY |
| Парткод: | 2BM27120 |
| Деталь: | CLUTCH 26-B |
| Парткод: | 2BM27780 |
| Деталь: | BUSH METAL |
| Парткод: | 2BM07330 |
| Деталь: | PLATE DRIVE MPF ASSY |
| Парткод: | 2BM68150 |
| Деталь: | GEAR MPF Z28 Z30 |
| Парткод: | 2BM07240 |
| Деталь: | SHAFT GEAR MPF |
| Парткод: | 2BM07250 |
| Деталь: | HOLDER DRIVE MPF |
| Парткод: | 2BM07230 |
| Деталь: | SOLENOID MPF |
| Парткод: | 2BM27100 |
| Деталь: | PLATE DRIVE MPF |
| Парткод: | 2BM07220 |
| Деталь: | EDGING,ES-0505-2(NIKKO) |
| Парткод: | M2504030 |
| Деталь: | SEAL MPF |
| Парткод: | 2BM07380 |
| Деталь: | PT.SENSOR GP2S30 |
| Парткод: | 2BM27170 |
| Деталь: | CONN.CORD PSIZE ASSY |
| Парткод: | 2BM27140 |
| Деталь: | WIRE MPF |
| Парткод: | 2A627820 |
| Деталь: | JUNCTION WIRING MPF |
| Парткод: | 2A627830 |
| Деталь: | COVER PWB MPF |
| Парткод: | 2BM07030 |
| Деталь: | SPRING RETARD MPF |
| Парткод: | 2BM07290 |
| Деталь: | SPRING BOTTOM MPF |
| Парткод: | 2BM07080 |
| Деталь: | LABEL PAPER TYPE E |
| Парткод: | 2BM05250 |
| Деталь: | PARTS,DEVELOPING UNIT (C),(USA) |
| Парткод: | 2A693130 |
| Деталь: | PARTS,DEVELOPING UNIT (c),(j/E) |
| Парткод: | 2A693140 |
| Деталь: | CASE DLP D3 (1/2) |
| Парткод: | 2BM15110 |
| Деталь: | TONER SENSOR ASSY |
| Парткод: | 2BM27330 |
| Деталь: | SENSOR FACE D1234 |
| Парткод: | 2BM14310 |
| Деталь: | SEAL SIDE D24 |
| Парткод: | 2BM40570 |
| Деталь: | MAGNET SEAL D1234 |
| Парткод: | 2BM40560 |
| Деталь: | SEAL CASE E D3 |
| Парткод: | 2BM15400 |
| Деталь: | SCRAPER PULLEY D1234 |
| Парткод: | 2BM14300 |
| Деталь: | MAGNET MIXER D1234 |
| Парткод: | 2BM14180 |
| Деталь: | SEAL BUSH D1234 |
| Парткод: | 2BM40190 |
| Деталь: | SPACER D1234 |
| Парткод: | 2BM40200 |
| Деталь: | OIL SEAL |
| Парткод: | 2BM14390 |
| Деталь: | BUSH D1234 |
| Парткод: | 2BM14330 |
| Деталь: | SHAFT SUPPLY B D3 |
| Парткод: | 2BM15230 |
| Деталь: | GEAR BEVEL Z16 D3 |
| Парткод: | 2BM15180 |
| Деталь: | Bush |
| Парткод: | 2BM14530 |
| Деталь: | GEAR Z18-8 D3 |
| Парткод: | 2BM15170 |
| Деталь: | BUSH BLOCK SUPPLY D3 |
| Парткод: | 2BM15240 |
| Деталь: | SCREW SUPPLY D3 |
| Парткод: | 2BM15120 |
| Деталь: | GEAR Z19-5 D3 |
| Парткод: | 2BM15190 |
| Деталь: | GEAR Z35-5 D3 |
| Парткод: | 2BM15210 |
| Деталь: | SHAFT SUPPLY A D3 |
| Парткод: | 2BM15220 |
| Деталь: | GEAR Z18-5 D3 |
| Парткод: | 2BM15200 |
| Деталь: | SHAFT CROSS D3 ASSY |
| Парткод: | 2BM00850 |
| Деталь: | SHAFT GEAR MIX 1 |
| Парткод: | 2BM40230 |
| Деталь: | GEAR Z28-5 MIX2 |
| Парткод: | 2BM40220 |
| Деталь: | GEAR MIXER 1 D123 |
| Парткод: | 2BM14410 |
| Деталь: | TUBE MIXER D1234 |
| Парткод: | 2BM14130 |
| Деталь: | FLANGE MIXER L D1234 |
| Парткод: | 2BM14150 |
| Деталь: | SCREW MIXER D1234 |
| Парткод: | 2BM14160 |
| Деталь: | SHAFT MIXER D123 |
| Парткод: | 2BM40100 |
| Деталь: | FLANGE MIXER R D1234 |
| Парткод: | 2BM14170 |
| Деталь: | SCRAPER MIXER D1234 |
| Парткод: | 2BM40580 |
| Деталь: | GEAR MIXER 2 D123 |
| Парткод: | 2BM14420 |
| Деталь: | STAY D3 |
| Парткод: | 2BM15130 |
| Деталь: | SEAL CASE D134 |
| Парткод: | 2BM14630 |
| Деталь: | SEAL BLADE D1234 |
| Парткод: | 2BM14320 |
| Деталь: | SEAL CASE A D3 |
| Парткод: | 2BM15360 |
| Деталь: | SEAL CASE B D3 |
| Парткод: | 2BM15370 |
| Деталь: | SEAL CASE C D3 |
| Парткод: | 2BM15380 |
| Деталь: | SEAL CASE D D3 |
| Парткод: | 2BM15390 |
| Деталь: | SEAL CASE D123 |
| Парткод: | 2BM14500 |
| Деталь: | ROLLER MAGNET D23 |
| Парткод: | 2BM14940 |
| Деталь: | PULLY D1234 |
| Парткод: | 2BM14010 |
| Деталь: | GAER MG H D1234 |
| Парткод: | 2BM40460 |
| Деталь: | SHAFT CASE D3 |
| Парткод: | 2BM15320 |
| Деталь: | GEAR Z15 |
| Парткод: | 2BM15410 |
| Деталь: | Gear Z38S |
| Парткод: | 2BM15420 |
| Деталь: | GEAR Z25-Z15-8 D3 |
| Парткод: | 2BM15280 |
| Деталь: | FLANGE R D3 |
| Парткод: | 2BM15140 |
| Деталь: | RING STOPPER |
| Парткод: | 2A806250 |
| Деталь: | ROLLER BLADE D1234 |
| Парткод: | 2BM14030 |
| Деталь: | SHAFT MG BLADE D1234 |
| Парткод: | 2BM14040 |
| Деталь: | BUSH BIAS D1234 |
| Парткод: | 2BM14220 |
| Деталь: | SP MG BLADE D1234 |
| Парткод: | 2BM14290 |
| Деталь: | JOINT MG D1234 |
| Парткод: | 2BM14050 |
| Деталь: | GEAR Z25H D3 |
| Парткод: | 2BM40440 |
| Деталь: | PITCH PIECE R D3 |
| Парткод: | 2BM15160 |
| Деталь: | PITCH PIECE F D3 |
| Парткод: | 2BM15270 |
| Деталь: | BIAS JOINT D123 |
| Парткод: | 2BM14400 |
| Деталь: | PRESSDCUT D1234 |
| Парткод: | 2BM40040 |
| Деталь: | PLATE IDLE D23 |
| Парткод: | 2BM14930 |
| Деталь: | GEAR Z20-5 D1234 |
| Парткод: | 2BM14110 |
| Деталь: | CUT WASHER |
| Парткод: | 2BM40060 |
| Деталь: | GEAR Z38-5 D23 |
| Парткод: | 2BM14910 |
| Деталь: | COVER F D3 |
| Парткод: | 2BM15290 |
| Деталь: | SEAL MG D1234 |
| Парткод: | 2BM40300 |
| Деталь: | BKT CLUTCH D3 |
| Парткод: | 2BM15150 |
| Деталь: | GEAR Z30H-Z22H D34 |
| Парткод: | 2BM40650 |
| Деталь: | CLUTCH 26-F |
| Парткод: | 2BM27490 |
| Деталь: | SEAL CLUTH D1234 |
| Парткод: | 2BM40150 |
| Деталь: | SHAFT CLUTCH D1234 |
| Парткод: | 2BM14070 |
| Деталь: | JOINT D1234 |
| Парткод: | 2BM14090 |
| Деталь: | POLY WASHER 16 |
| Парткод: | 2BM40500 |
| Деталь: | BALL BEARING D1234 |
| Парткод: | 2BM40310 |
| Деталь: | POLY WASHER 14 |
| Парткод: | 2BM40510 |
| Деталь: | GEAR Z14D-8 D1234 |
| Парткод: | 2BM40360 |
| Деталь: | GEAR Z15-8 D123 |
| Парткод: | 2BM40370 |
| Деталь: | GEAR Z14-Z12 D123 |
| Парткод: | 2BM40590 |
| Деталь: | GUIDE TCNT D3 |
| Парткод: | 2BM15250 |
| Деталь: | SHEET HEAT A D3 |
| Парткод: | 2BM40600 |
| Деталь: | SHEET HEAT B D3 |
| Парткод: | 2BM40610 |
| Деталь: | GUIDE SHUTTER D1234 |
| Парткод: | 2BM14200 |
| Деталь: | SEAL GUIDE T D1234 |
| Парткод: | 2BM14260 |
| Деталь: | SEAL SHUTTER D1234 |
| Парткод: | 2BM14250 |
| Деталь: | SHUTTER D1234 |
| Парткод: | 2BM14240 |
| Деталь: | SPRING SHUTTER D1234 |
| Парткод: | 2BM14230 |
| Деталь: | LOCK SHUTTER D1234 |
| Парткод: | 2BM14120 |
| Деталь: | PW.BOARD KP-819 ASSY |
| Парткод: | 2BM01140 |
| Деталь: | CONN.CORD LED D3 ASSY |
| Парткод: | 2BM27510 |
| Деталь: | GUIDE SCREW D23 |
| Парткод: | 2BM14890 |
| Деталь: | PLATE MOTOR TONER D3 |
| Парткод: | 2BM15260 |
| Деталь: | GEAR Z31-Z15-8 D123 |
| Парткод: | 2BM14460 |
| Деталь: | SP JOINT T SRP D23 |
| Парткод: | 2BM14920 |
| Деталь: | JOINT SCRAPER CI D |
| Парткод: | 2A614070 |
| Деталь: | GEAR Z14-8 D23 |
| Парткод: | 2BM14280 |
| Деталь: | DC motor |
| Парткод: | 2BM27340 |
| Деталь: | GEAR WORM |
| Парткод: | 2BM14540 |
| Деталь: | CONN.CORD TM D3 ASSY |
| Парткод: | 2BM27530 |
| Деталь: | JOINT FEED T D123 |
| Парткод: | 2BM14470 |
| Деталь: | SP JOINT T SW D1234 |
| Парткод: | 2BM14190 |
| Деталь: | BKT JOINT TCNT D23 |
| Парткод: | 2BM14880 |
| Деталь: | WORM WHEEL D123 |
| Парткод: | 2BM14480 |
| Деталь: | WIRE C,DEVELOPING |
| Парткод: | 2A627610 |
| Деталь: | LABEL POSITION C |
| Парткод: | 2BM05200 |
| Деталь: | COVER TCNT D23 |
| Парткод: | 2BM14900 |
| Деталь: | PW.BOARD KP-820 ASSY |
| Парткод: | 2BM01150 |
| Деталь: | CONN.CORD PTR D3 ASSY |
| Парткод: | 2BM27520 |
| Деталь: | DETECTION PLATE D3,DEVELOPING(F) |
| Парткод: | 2A614050 |
| Деталь: | DETECTION PLATE D3,DEVELOPING(G) |
| Парткод: | 2A614060 |
| Деталь: | SEAL SCREW D3 |
| Парткод: | 2BM40790 |
| Деталь: | COVER PWB D234 |
| Парткод: | 2BM14870 |
| Деталь: | SHEET HEAT C D3 |
| Парткод: | 2BM40620 |
| Деталь: | SHEET HEAT D D3 |
| Парткод: | 2BM40630 |
| Деталь: | PRESS PIECE D3 |
| Парткод: | 2BM15300 |
| Деталь: | SPRING D3 |
| Парткод: | 2BM15350 |
| Деталь: | COVER MAG D3 |
| Парткод: | 2BM15340 |
| Деталь: | SEAL LID DEVE D1234 |
| Парткод: | 2BM14270 |
| Деталь: | SHEET PWB D1234 |
| Парткод: | 2BM40140 |
| Деталь: | COVER R D3 |
| Парткод: | 2BM15310 |
| Деталь: | PLATE ANGLE D123 |
| Парткод: | 2BM14440 |
| Деталь: | SIMM D1234 |
| Парткод: | 2BM40700 |
| Деталь: | SCANNER UNIT ASSY |
| Парткод: | 2A600161 |
| Деталь: | SCANNER FRAME ASSY |
| Парткод: | 2A600010 |
| Деталь: | PULLEY,SCANNER DRUM |
| Парткод: | 2A612380 |
| Деталь: | PARTS,WIRE SCANNER(SP) |
| Парткод: | 2A693070 |
| Деталь: | SHAFT,WIRE DRUM |
| Парткод: | 2A612090 |
| Деталь: | BEARING,688ZZNR |
| Парткод: | 28107400 |
| Деталь: | STOPPER 7,CARTRIDGE |
| Парткод: | 33973300 |
| Деталь: | SCANNER DRIVE PULLEY |
| Парткод: | 2A612310 |
| Деталь: | PULLEY A,SCANNER WIRE |
| Парткод: | 35912040 |
| Деталь: | STOPPER 5 |
| Парткод: | 34806150 |
| Деталь: | MOUNT,SCANNER PULLEY |
| Парткод: | 2A012130 |
| Деталь: | ADJUSTING PLATE,PULLEY |
| Парткод: | 2A612290 |
| Деталь: | PULLEY 16/64 |
| Парткод: | 2A612280 |
| Деталь: | FRONT SHIELD,SCANNER |
| Парткод: | 2A612490 |
| Деталь: | BELT B,SCANNER |
| Парткод: | 2A612320 |
| Деталь: | MOTOR,SCANNER |
| Парткод: | 2A612270 |
| Деталь: | MOUNT,SCANNER MOTOR |
| Парткод: | 2A612160 |
| Деталь: | BELT A,SCANNER |
| Парткод: | 2A612300 |
| Деталь: | MIRROR FRAME,SCANNER |
| Парткод: | 2A612130 |
| Деталь: | GUIDE FFC2 |
| Парткод: | 35912360 |
| Деталь: | ADJUSTING PLATE,MIRROR FRAME PULLEY |
| Парткод: | 2A612250 |
| Деталь: | SLIDER,SCANNER |
| Парткод: | 18512090 |
| Деталь: | MIRROR B,SCANNER |
| Парткод: | 2A612140 |
| Деталь: | MIRROR HOLDER |
| Парткод: | 75712080 |
| Деталь: | SPRING,SCANNER |
| Парткод: | 2A612400 |
| Деталь: | MIRROR A,SCANNER |
| Парткод: | 2A612120 |
| Деталь: | SPRING,MIRROR HOLDER |
| Парткод: | 35912210 |
| Деталь: | PARTS,PCB INVERTER(SP) |
| Парткод: | 2A693060 |
| Деталь: | SPACER,INVERTER PCB |
| Парткод: | 2A612260 |
| Деталь: | MOUNT BASE,LAMP |
| Парткод: | 2A612110 |
| Деталь: | PARTS,LAMP SCANNER(SP) |
| Парткод: | 2A693020 |
| Деталь: | MINIATURE CLAMP,UAMS-05S-2 |
| Парткод: | M2105740 |
| Деталь: | WIRE,LAMP INVERTER |
| Парткод: | 2A627380 |
| Деталь: | GUIDE FFC1 |
| Парткод: | 2AV12080 |
| Деталь: | UPPER GUIDE FILM FFC |
| Парткод: | 2A612330 |
| Деталь: | RETAINER,WIRE |
| Парткод: | 35912140 |
| Деталь: | FEED GUIDE,SCANNER WIRE |
| Парткод: | 2A612180 |
| Деталь: | SENSOR,ORIGINAL DETECTION |
| Парткод: | 35927290 |
| Деталь: | WIRE,SCANNER UNIT |
| Парткод: | 2A627710 |
| Деталь: | LOWER GRAND PLATE,SCANNER |
| Парткод: | 2A626150 |
| Деталь: | PULLEY SCANNER WIRE |
| Парткод: | 2A612480 |
| Деталь: | REINFORCEMENT,ORIGINAL HOLDER |
| Парткод: | 2A612220 |
| Деталь: | MOUNT,SCANNER PI |
| Парткод: | 2A612170 |
| Деталь: | SWITCH,FEED |
| Парткод: | 35327400 |
| Деталь: | RELEASE SWITCH ASSY |
| Парткод: | 2AC00580 |
| Деталь: | MOUNT,RELEASE SWITCH |
| Парткод: | 2AC12230 |
| Деталь: | GUIDE,RELEASE SWITCH |
| Парткод: | 2AC12360 |
| Деталь: | SWITCH,RELEASE DETECTION |
| Парткод: | 2AC12370 |
| Деталь: | SPRING,RELEASE SWITCH |
| Парткод: | 2AC12380 |
| Деталь: | COVER,SCANNER DRIVE |
| Парткод: | 2A612340 |
| Деталь: | CUSHION,CONTACT GLASS |
| Парткод: | 29812291 |
| Деталь: | COVER,ISU |
| Парткод: | 2A612240 |
| Деталь: | LABEL,CAUTION CONTACT GLASS |
| Парткод: | 2A105180 |
| Деталь: | REFLECTOR,SCANNER |
| Парткод: | 2A612410 |
| Деталь: | VIBRATION INSULATOR,MIRROR |
| Парткод: | 2A612450 |
| Деталь: | LID,NIC |
| Парткод: | 2A626120 |
| Деталь: | HOLDER,JOINT |
| Парткод: | 33921200 |
| Деталь: | SHEET B,INVERTER PCB |
| Парткод: | 2A612460 |
| Деталь: | PIN,TENSHION(M4) |
| Парткод: | 2A612370 |
| Деталь: | CONTACT GLASS,ADF |
| Парткод: | 2A612440 |
| Деталь: | HOLDER,ADF CONTACT GLASS |
| Парткод: | 2AV12300 |
| Деталь: | SPONGE,ORIGINAL SIZE INDICATOR |
| Парткод: | 35912531 |
| Деталь: | LEFT ORIGINAL SIZE INDICATOR |
| Парткод: | 2A612200 |
| Деталь: | STANDARD PLATE,SHADING |
| Парткод: | 2A612210 |
| Деталь: | LABEL,ORIGINAL SIZE INDICATOR(METRIC) |
| Парткод: | 2AV12481 |
| Деталь: | LABEL,ORIGINAL SIZE INDICATOR(INCH) |
| Парткод: | 2AV12491 |
| Деталь: | CONTACT GLASS |
| Парткод: | 35912010 |
| Деталь: | REAR ORIGINAL SIZE INDICATOR(METRIC) |
| Парткод: | 2AV12460 |
| Деталь: | REAR ORIGINAL SIZE INDICATOR(lNCH) |
| Парткод: | 2AV12470 |
| Деталь: | FRONT SEAL,CONTACT GLASS |
| Парткод: | 2A612350 |
| Деталь: | AUXILIARY PLATE,ORIGINAL HOLDER |
| Парткод: | 2A612230 |
| Деталь: | UPPER SHIELD,SCANNER |
| Парткод: | 2A612470 |
| Деталь: | SWITCH INTERLOCK |
| Парткод: | 2BL27480 |
| Деталь: | WIRE FAX,INTERLOCK |
| Парткод: | 2A627790 |
| Деталь: | CONN.CORD HV-MAIN ASSY |
| Парткод: | 2BM28650 |
| Деталь: | CONN.CORD HV T2 ASSY |
| Парткод: | 2BM28790 |
| Деталь: | CONN.CORD HV G ASSY |
| Парткод: | 2BM28860 |
| Деталь: | CONN.CORD HV MAIN ASSY |
| Парткод: | 2BM28870 |
| Деталь: | CONN.CORD D.FEED ASSY |
| Парткод: | 2BM28560 |
| Деталь: | CONN.CORD S2568 ASSY |
| Парткод: | 2BM28590 |
| Деталь: | CONN.CORD FEED ASSY |
| Парткод: | 2BM28670 |
| Деталь: | CONN.CORD FEED MOTOR ASSY |
| Парткод: | 2BM28570 |
| Деталь: | CONN.CORD HV ASSY |
| Парткод: | 2BM28850 |
| Деталь: | CONN.CORD HV T1 ASSY |
| Парткод: | 2BM28800 |
| Деталь: | CONN.CORD HV BK ASSY |
| Парткод: | 2BM28840 |
| Деталь: | CONN.CORD HV BC ASSY |
| Парткод: | 2BM28830 |
| Деталь: | CONN.CORD HV BM ASSY |
| Парткод: | 2BM28820 |
| Деталь: | CONN.CORD HV BY ASSY |
| Парткод: | 2BM28810 |
| Деталь: | JUNCTION WIRING,MAIN SWITCH |
| Парткод: | 2A627361 |
| Деталь: | CONN.CORD APC ASSY |
| Парткод: | 2BM28520 |
| Деталь: | WIRE,COVER SWITCH |
| Парткод: | 2A627530 |
| Деталь: | CONN.CORD TSENSOR D4 ASSY |
| Парткод: | 2BM28960 |
| Деталь: | MOUNT,MAIN SWITCH |
| Парткод: | 2A626100 |
| Деталь: | SWITCH,MAIN |
| Парткод: | 2A627030 |
| Деталь: | EDGING EDS-1 |
| Парткод: | M2104200 |
| Деталь: | WIRE,MAIN SWITCH PRIMARY |
| Парткод: | 2A627290 |
| Деталь: | CONN.CORD HD.DLP ASSY |
| Парткод: | 2BM28530 |
| Деталь: | POWER CORD(120) |
| Парткод: | 19527400 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | POWER CODE AS(240) |
| Парткод: | 29927231 |
| Деталь: | CONN.CORD D.FEED2 ASSY |
| Парткод: | 2BM28600 |
| Деталь: | CONN.CORD DRIVE MAIN ASSY |
| Парткод: | 2BM27610 |
| Деталь: | CONN.CORD HV T12 ASSY |
| Парткод: | 2BM28880 |
| Деталь: | CONN.CORD DLP MOTOR ASSY |
| Парткод: | 2BM28610 |
| Деталь: | CONN.CORD MAIN MOTOR ASSY |
| Парткод: | 2BM28620 |
| Деталь: | CONN.CORD HV UNIT ASSY |
| Парткод: | 2BM28890 |
| Деталь: | CONN.CORD OPRERAY ASSY |
| Парткод: | 2BM28710 |
| Деталь: | CONN.CORD HV-T2 ASSY |
| Парткод: | 2BM28660 |
| Деталь: | CONN.CORD PF/DU ASSY |
| Парткод: | 2BM28720 |
| Деталь: | WIRE,MIDDLE TRANSFER |
| Парткод: | 2A627550 |
| Деталь: | WIRE,FIXING CONTROL |
| Парткод: | 2A627630 |
| Деталь: | WIRE,DRUM CONTROL |
| Парткод: | 2A627780 |
| Деталь: | CONN.CORD S02597 ASSY |
| Парткод: | 2BM28760 |
| Деталь: | WIRE YM,DEVELOPING CONTROL |
| Парткод: | 2A627570 |
| Деталь: | WIRE CK,DEVELOPING CONTROL |
| Парткод: | 2A627580 |
| Деталь: | CONN.CORD OILROLLFUSEASSY |
| Парткод: | 2BM28910 |
| Деталь: | MOUNT,ELECTRICAL COMPONENT |
| Парткод: | 2A626010 |
| Деталь: | COVER,ELECTRICAL COMPONENT |
| Парткод: | 2A626210 |
| Деталь: | WIRE,OPERATION UNIT KEYBOARD |
| Парткод: | 2A627040 |
| Деталь: | WIRE,OPERATION UNIT LED |
| Парткод: | 2A627050 |
| Деталь: | WIRE,LCD |
| Парткод: | 2A627060 |
| Деталь: | WIRE,INTERFACE CONTROL |
| Парткод: | 2A627010 |
| Деталь: | WIRE,INTERFACE DATA |
| Парткод: | 2A627020 |
| Деталь: | JUNCTION WIRING,MAIN PCB POWER SOURCE |
| Парткод: | 2A627480 |
| Деталь: | WIRE,MAIN SWITCH |
| Парткод: | 2A627151 |
| Деталь: | JUNCTION WIRING,KEY COUNTER |
| Парткод: | 2A627160 |
| Деталь: | WIRE,OPTION CONTROL |
| Парткод: | 2A627130 |
| Деталь: | WIRE FAX,RELAY |
| Парткод: | 2A627690 |
| Деталь: | FAN,COOLING |
| Парткод: | 2A627740 |
| Деталь: | WIRE,ELECTRICAL COMPONENT COOLING |
| Парткод: | 2A627730 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | 2A601010 |
| Деталь: | SCANNER SUB PCB |
| Парткод: | 2A628050 |
| Деталь: | RTC ASSY |
| Парткод: | 2A601120 |
| Деталь: | MOUNT,TOTAL COUNTER |
| Парткод: | 2A626160 |
| Деталь: | COUNTER,TOTAL |
| Парткод: | 2A627490 |
| Деталь: | WIRE,SCANNER UNIT JUNCTION |
| Парткод: | 2A627700 |
| Деталь: | WIRE,TOTAL COUNTER |
| Парткод: | 2A627250 |
| Деталь: | JUNCTION WIRING,FEEDER |
| Парткод: | 2A627100 |
| Деталь: | WIRE,FEEDER POWER SOURCE |
| Парткод: | 2A627720 |
| Деталь: | GUIDE,CF |
| Парткод: | 2A626110 |
| Деталь: | LID,NIC |
| Парткод: | 2A626120 |
| Деталь: | LID,VENDOR |
| Парткод: | 36726140 |
| Деталь: | LOWER GRAND PLATE,SCANNER |
| Парткод: | 2A626150 |
| Деталь: | LID FINISHER CABLE |
| Парткод: | 77502090 |
| Деталь: | SPACER,FGS-6S(KITAGAWA) |
| Парткод: | M2108790 |
| Деталь: | WIRE,KEY COUNTER |
| Парткод: | 2A627810 |
| Деталь: | FD UNIT ASSY |
| Парткод: | 2A600170 |
| Деталь: | FRAME FD |
| Парткод: | 2BM21010 |
| Деталь: | ACTUATOR SENSOR FU |
| Парткод: | 2BM21260 |
| Деталь: | SPRING ACT FU |
| Парткод: | 2BM21400 |
| Деталь: | ACTUATOR SENSOR FD |
| Парткод: | 2BM21130 |
| Деталь: | SPRING ACT MIDDLE |
| Парткод: | 2BM21390 |
| Деталь: | FAN FD |
| Парткод: | 2BM21630 |
| Деталь: | PLATE PRESS DLP BASE |
| Парткод: | 2BM21090 |
| Деталь: | ARM PRESS DLP |
| Парткод: | 2BM21100 |
| Деталь: | SPRING PRESS DLP |
| Парткод: | 2BM21110 |
| Деталь: | SOLENOID FD |
| Парткод: | 2BM27800 |
| Деталь: | LEVER SOLENOID |
| Парткод: | 2BM21050 |
| Деталь: | SPRING SOL |
| Парткод: | 2BM21060 |
| Деталь: | FD PLATE SOLENOID |
| Парткод: | 2BM21040 |
| Деталь: | GUIDE CHANGE |
| Парткод: | 2BM21080 |
| Деталь: | LEVER GUIDE CHANGE |
| Парткод: | 2BM21070 |
| Деталь: | STOPPER PI |
| Парткод: | 2BM17990 |
| Деталь: | SPRING EXIT |
| Парткод: | 2BM21530 |
| Деталь: | Bush SP |
| Парткод: | 2BM20610 |
| Деталь: | PULLEY EXIT A |
| Парткод: | 2BM21160 |
| Деталь: | SHAFT ROLLER FD |
| Парткод: | 2BM21170 |
| Деталь: | ROLLER FD |
| Парткод: | 2BM21200 |
| Деталь: | NOB ROLL FD |
| Парткод: | 2BM21440 |
| Деталь: | BUSH DRUM |
| Парткод: | 2BM21210 |
| Деталь: | BRUSH ERASER S |
| Парткод: | 2BM21610 |
| Деталь: | SPRING EXIT |
| Парткод: | 2BM21480 |
| Деталь: | PULLY A,EJECT |
| Парткод: | 2A621270 |
| Деталь: | PULLY B,EJECT |
| Парткод: | 2A621280 |
| Деталь: | UPPER GUIDE,EJECT |
| Парткод: | 2A621200 |
| Деталь: | RING STOPPER |
| Парткод: | 5MVXIIIDN003 |
| Деталь: | GROUND PLATE,EJECT |
| Парткод: | 2A621220 |
| Деталь: | LOCK COVER FU |
| Парткод: | 2BM21350 |
| Деталь: | PLATE EARTH SWITCH |
| Парткод: | 2BM21450 |
| Деталь: | FILM SWITCH |
| Парткод: | 2BM21650 |
| Деталь: | PIN IDLE 2 |
| Парткод: | 2BM21310 |
| Деталь: | PIN IDLE 1 |
| Парткод: | 2BM21300 |
| Деталь: | GEAR Z26 |
| Парткод: | 2BM21140 |
| Деталь: | GEAR Z22 |
| Парткод: | 2BM21330 |
| Деталь: | FD PULLEY GEAR Z18 |
| Парткод: | 2BM21250 |
| Деталь: | FD PULLEY BELT Z18 |
| Парткод: | 2BM21220 |
| Деталь: | BELT FD 264 |
| Парткод: | 2BM21270 |
| Деталь: | BELT FD 156 |
| Парткод: | 2BM21280 |
| Деталь: | FD FLANGE BELT |
| Парткод: | 2BM21230 |
| Деталь: | BKT PITCH JOINT |
| Парткод: | 2BM21470 |
| Деталь: | SPRING,FD JOINT |
| Парткод: | 2A621300 |
| Деталь: | PLATE JOINT |
| Парткод: | 2BM21410 |
| Деталь: | PIN JOINT |
| Парткод: | 2BM21430 |
| Деталь: | PROTECT BOARD |
| Парткод: | 2BM21600 |
| Деталь: | P.W.BOARD KP-828 ASSY |
| Парткод: | 2BM01190 |
| Деталь: | JUNCTION WIRING,FACE DOWN |
| Парткод: | 2A627520 |
| Деталь: | CONN.CORD C.SWITCHASSY |
| Парткод: | 2BM27830 |
| Деталь: | CONN.CORD P.FULLASSY |
| Парткод: | 2BM27820 |
| Деталь: | COVER CORD FD |
| Парткод: | 2BM21640 |
| Деталь: | COVER GEAR FD |
| Парткод: | 2BM21030 |
| Деталь: | P.W.BOARD KP-809 ASSY |
| Парткод: | 2BM01090 |
| Деталь: | GEAR INPUT Z24 |
| Парткод: | 2BM21340 |
| Деталь: | STOPPER 5 |
| Парткод: | 34806150 |
| Деталь: | SPONGE,EJECT |
| Парткод: | 2A621290 |
| Деталь: | UPPER EJECT,ACTUATOR |
| Парткод: | 2A621210 |
| Деталь: | PT.SENSOR GP1S74P |
| Парткод: | 2BM27240 |
| Деталь: | GEAR 18,LOOP |
| Парткод: | 73210370 |
| Деталь: | LEVER,FEED SHIFT GUIDE |
| Парткод: | 2A621070 |
| Деталь: | SOLENOID B,CLEANING |
| Парткод: | 61727681 |
| Деталь: | SPRING,SOLENOID RELEASE |
| Парткод: | 2A621260 |
| Деталь: | MOUNT,SOLENOID |
| Парткод: | 2A621060 |
| Деталь: | LEVER,SOLENOID |
| Парткод: | 2A621080 |
| Деталь: | COVER FD ASSY |
| Парткод: | 2BM00880 |
| Деталь: | COVER FD ASSY |
| Парткод: | 2BM68200 |
| Деталь: | SPRING LEVER FD F |
| Парткод: | 2BM21580 |
| Деталь: | LEVER COVER FD |
| Парткод: | 2BM21500 |
| Деталь: | WIRE EARTH FD |
| Парткод: | 2BM42590 |
| Деталь: | COVER FD |
| Парткод: | 2BM21490 |
| Деталь: | PLATE FDC R |
| Парткод: | 2BM21560 |
| Деталь: | SPRING LEVER FD R |
| Парткод: | 2BM21570 |
| Деталь: | PLATE FDC F |
| Парткод: | 2BM21550 |
| Деталь: | STOPPER COVER FD |
| Парткод: | 2BM21380 |
| Деталь: | BRUSH ERASER |
| Парткод: | 2BM21460 |
| Деталь: | CASE EXIT FU |
| Парткод: | 2BM21510 |
Коды ошибок
C0030
C0070
C0110
C0120
C0130
C0220
C0240
C0250
C0280
C0290
C0440
C0460
C0600
C0610
C0630
C0640
C0700
C0710
C0810
C0820
C0830
C0840
C0850
C0860
C1010
C1020
C1030
C1040
C1200
C1210
C2000
C2010
C2020
C2101
C2102
C2111
C2112
C2121
C2122
C2340
C2500
C2510
C2520
C3100
C3200
C4000
C4200
C5120
C5300
C6000
C6010
C6020
C6030
C6040
C6100
C6110
C6120
C6130
C6140
C6430
C7001
C7002
C7003
C7004
C7101
C7102
C7103
C7104
C7301
C7600
C7610
C7700
C7710
C7800
C7810
C8000
C8010
C8030
C8140
C8170
C8180
C8210
C8220
Описание
| Error code: | C0030 |
| Description: | FAX PWB system error |
| Causes: | The FAX processing cannot be continued due to the FAX firmware error. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. |
| Error code: | C0070 |
| Description: | Toner motor |
| Causes: | Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Remedy: | 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0110 |
| Description: | Backup memory data problem (main PWB) • Data in the specified area of the backup memory does not match the specified values. |
| Causes: | Problem with the backup memory data. Defective main PWB. |
| Remedy: | Problem with the backup memory data. Run maintenance item U021 to set the contents of the backup memory data again. Defective main PWB. If the C0110 is displayed after initializing the backup memory, replace the main PWB and check for correct operation. |
| Error code: | C0120 |
| Description: | MAC address data error |
| Causes: | The MAC address data is incorrect. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the MAC address The MAC address is incorrect. Replace the main PWB when the MAC address is not indicated on the network status page. |
| Error code: | C0130 |
| Description: | Backup memory read / write error |
| Causes: | The reading or writing into the flash memory is unavailable. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reconnect the connectors on the main PWB. At that time, fix or replace the wires if they are pinched by other parts or have any damage. When the issue is not resolved, replace the main PWB. |
| Error code: | C0220 |
| Description: | CPU communication problem • Synchronization cannot be taken between the main CPU and scanner CPU. |
| Causes: | Defective main PWB. Poor contact in the connector terminals. Defective scanner PWB. |
| Remedy: | Defective main PWB. Replace the main PWB. Poor contact in the connector terminals. Check the connection of connector YC2 on the engine PWB and YC5 on the scanner PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective scanner PWB. Replace the scanner PWB. |
| Error code: | C0240 |
| Description: | Printer board* communication problem • The printer board does not respond 120 seconds after the power is turned on. |
| Causes: | Poor contact in the connector terminals. DIMM installed incorrectly. Defective main PWB or printer board. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC9 on the main PWB and YC5 on the printer board, and the continuity across the connector terminals. Repair or replace if necessary. DIMM installed incorrectly. Check the connection. Repair or replace if necessary. Defective main PWB or printer board. Replace the main PWB or printer board and check for correct operation. |
| Error code: | C0250 |
| Description: | Network scanner board* communication problem • The response to the alive command to the network scanner transmitted once to 30 s does not come on the contrary three consecutive times or more. • The response to the communication command transmitted to the network scanner does not return 75 s or more. |
| Causes: | Poor contact in the connector terminals. Defective main PWB or network scanner board. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC3 on the main PWB and the connector on the network scanner board, and the continuity across the connector terminals. Repair or replace if necessary. Defective main PWB or network scanner board. Replace the main PWB or network scanner board and check for correct operation. |
| Error code: | C0280 |
| Description: | Communication problem between the fax control PWB and main PWB Communication between the fax control PWB and the main PWB of the machine cannot be performed normally. |
| Causes: | Poor contact in the connector terminals. Defective PWB. |
| Remedy: | Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective PWB. Replace the fax control PWB or main PWB and check for correct operation. |
| Error code: | C0290 |
| Description: | Communication problem between the scanner main PCB and fax board • The status cannot be normally received even if the fax board has retried command transmission 100 times. |
| Causes: | Poor contact in the connector terminals. Defective scanner main PCB or fax board. |
| Remedy: | Check the connection of connector CN26 on the scanner main PCB and the connector on the fax board. Repair or replace if necessary. Replace the scanner main PCB or fax board and check for correct operation. |
| Error code: | C0440 |
| Description: | Document finisher communication problem • A communication error from document finisher is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective finisher main PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC14 on the engine PWB and YC4 on the finisher main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective finisher main PWB. Replace the finisher main PWB. |
| Error code: | C0460 |
| Description: | Duplex unit communication problem • A communication error from duplex section is detected 10 times in succession. |
| Causes: | Poor contact in the connector terminals. Defective engine PWB. Defective duplex PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC2 on the engine PWB and YC2 on the duplex PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB. Defective duplex PWB. Replace the duplex PWB. |
| Error code: | C0600 |
| Description: | Scan problem |
| Causes: | DIMM installed incorrectly. Defective DIMM. |
| Remedy: | Check if the DIMM is inserted into the socket on the scanner main PCB correctly. Replace the DIMM and check for correct operation. |
| Error code: | C0610 |
| Description: | Lens drive problem |
| Causes: | Defective main PWB. |
| Remedy: | Replace the main PWB and check for correct operation. |
| Error code: | C0630 |
| Description: | DMA error |
| Causes: | DMA transmission of the image data does not finish within the certain time. |
| Remedy: | 1 Checking the connection 0 0 2 Checking the connection 0 0 3 Replacing the wire The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • DPCIS - DP relay PWB • DP relay PWB - Main PWB Wiring diagram 4 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. Detaching and reattaching the DP relay PWB 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0640 |
| Description: | Hard Disk error |
| Causes: | The HDD cannot be accessed properly. |
| Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0700 |
| Description: | Side feeder EEPROM error • An error occurs in EEPROM (U4) data read or write for the side feeder main PWB. |
| Causes: | Defective side feeder main PWB. |
| Remedy: | Replace the side feeder main PWB. |
| Error code: | C0710 |
| Description: | Backup memory data problem C • One slave code among three machine number backup data is judged to be broken. |
| Causes: | Broken backup memory. |
| Remedy: | Run maintenance item U004 and enter the correct machine model number. |
| Error code: | C0810 |
| Description: | SCC microcomputer status problem • Abnormal SCC microcomputer status has been detected. |
| Causes: | Defective scanner main PCB. |
| Remedy: | Replace the scanner main PCB and check for correct operation. |
| Error code: | C0820 |
| Description: | Fax control PWB CG ROM checksum error (optional fax) A checksum error occurred with the CG ROM data of the fax control PWB. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C0830 |
| Description: | FAX PWB flash program area checksum error |
| Causes: | The program stored in the flash memory on the FAX PWB is broken so it cannot perform. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 2 Checking the FAX PWB The FAX PWB is not properly connected. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0840 |
| Description: | RTC error ("Time for maintenance T" appears) |
| Causes: | [Check at start-up] • RTC values are old. • Power has not been turned on for over 5 years. • RTC value is older than 2000/1/1 00:01. [Periodic check per 5 minutes after start-up] • RTC values are older than the ones at the last check. • Partial operation by power reset after C840 error and "Time for Maintenance T" is indicated. |
| Remedy: | 1 Executing U906 The backup battery on the main PWB is faulty, and so, the RTC settings are erased after unplugging the power cord. Execute U906 to reset the display [Maintenance T]. After that, set the date/time (RTC) in the System menu. (It is necessary to execute this process whenever to unplug/plug the power cord.) Executing U906 2 Replacing the main PWB The main PWB is faulty, or the backup battery runs out. If service call error C0840 frequently appears after performing the previous step, replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0850 |
| Description: | TPM security chip error |
| Causes: | TPM is not accessible or an access error occurs after installing the security kit |
| Remedy: | 1 Reset the main power Main PWB does not operate properly Turn the power switch and main power switch off. Turn the power switch and main power switch on after passing 5s 2 Upgrading the firmware The firmware version is not the latest Upgrade the firmware to the latest version 3 Replacing main PWB Main PWB is faulty Replace main PWB |
| Error code: | C0860 |
| Description: | Fax control PWB software switch checksum error (optional fax) A checksum error occurred with the software switch value of the fax control PWB. |
| Causes: | Defective fax software. Defective fax control PWB. |
| Remedy: | Defective fax software. Install the fax software. Defective fax control PWB. Replace the fax control PWB and verify the operation. |
| Error code: | C1010 |
| Description: | Lift motor 1 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1020 |
| Description: | Lift motor 2 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1030 |
| Description: | Lift motor 3 error • When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on. This error is detected four times successively. • During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 3. Defective lift motor 3. Poor contact of lift motor 3 connector terminals. Defective lift limit switch 3. Poor contact of lift limit switch 3 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 3. Replace lift motor 3. Defective lift motor 3. Check for continuity across the coil. If none, replace lift motor 3. Poor contact of lift motor 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 3. Run maintenance item U031 and turn lift limit switch 3 on and off manually. Replace lift limit switch 3 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB |
| Error code: | C1040 |
| Description: | Lift motor 4 error • When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on. This error is detected four times successively. • During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 4. Defective lift motor 4. Poor contact of lift motor 4 connector terminals. Defective lift limit switch 4. Poor contact of lift limit switch 4 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 4. Replace lift motor 4. Defective lift motor 4. Check for continuity across the coil. If none, replace lift motor 4. Poor contact of lift motor 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 4. Run maintenance item U031 and turn lift limit switch 4 on and off manually. Replace lift limit switch 4 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB. |
| Error code: | C1200 |
| Description: | Duplex side registration motor error • The duplex side registration home position sensor does not detect the home position of the side registration guide. |
| Causes: | Defective duplex side registration home position sensor. Defective duplex side registration motor. Defective duplex PWB. |
| Remedy: | Defective duplex side registration home position sensor. Check the connection of connector YC29 on the engine PWB and the connector YC1 on the duplex PWB. Repair or replace if necessary. Defective duplex side registration motor. Replace the duplex side registration motor. Defective duplex PWB. Replace the duplex PWB. |
| Error code: | C1210 |
| Description: | Side registration home position sensor detection error • The side registration home position sensor does not detect home position of side registration guides. • Detection occurs twice continuously after the duplex unit is removed and then inserted. |
| Causes: | Defective side registration home position sensor. Defective side registration motor. Defective engine controller PCB. |
| Remedy: | Replace the side registration home position sensor. Replace the side registration motor. Replace the engine controller PCB and check for correct operation. |
| Error code: | C2000 |
| Description: | Drive motor problem Stable OFF is detected for 1 s continuously after drive motor stability. The drive motor is not stabilized in 6 s since the motor is activated. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective drive motor. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC11 on the engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective drive motor. Replace the drive motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | C2010 |
| Description: | Main motor startup error |
| Causes: | The main motor is not in the steady state within 3s after start-up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Main motor - Engine PWB 3 Checking drive unit 1 Drive unit 1 is faulty. Execute U030[Main] and check if the gear in drive unit 1 rotates normally. If there is a load in rotation, clean the gear and bushing and apply grease. If not repaired, replace drive unit 1. 4 Checking the main motor The main motor is not attached properly, or it is faulty. Reattach the main motor and execute U030[Main]. If not operating normally, replace it. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB and then execute U411 [Table(ChartA)]. |
| Error code: | C2020 |
| Description: | Main drive motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency within 30 s since ASIC (U8) on the engine controller PCB has issued a motor activation signal to the main drive motor. |
| Causes: | Defective engine controller PCB. Defective main drive motor. Excessive torque for driving drum unit or primary transfer unit. (Overloaded by a damaged gear.) Defective harness between engine controller PCB and main drive motor, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the main drive motor. Check if the drum unit or primary transfer unit rotates smoothly. Check for broken gears. Replace if any. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C2101 |
| Description: | Developer motor error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking the developer motor The developer motor drive is faulty. Execute U030 [DLP(K)] and check the developer motor K operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 5 Checking the developer motor The developer motor is not properly attached or faulty. Reattach the developer motor. If not repaired, replace the motor. Detaching and reattaching the developer motor 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2102 |
| Description: | Developer motor C error |
| Causes: | 1. The ready signal is not at the L level when passing 2s after the developer motor C drive starts. 2. The ready signal is at the H level for 1s continuously after developer motor C is stable. |
| Remedy: | 1 Checking the developer drive section The developer drive section is faulty. Replace the developer unit drive gear if it is faulty. 2 Checking the developer roller The developer roller is faulty. Check if the developer roller rotates, and replace the developer unit if not rotating. Detaching and reattaching the developer unit 3 Checking developer motor C The developer motor C drive is faulty. Execute U030 [DLP(C)] and check the developer motor C operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor C - Motor relay PWB • Motor relay PWB - Engine PWB Wiring diagram 5 Checking developer motor C Developer motor C is not properly attached or faulty. Reattach developer motor C. If not repaired, replace the motor. Detaching and reattaching the main drive unit 6 Replacing the motor relay PWB The motor relay PWB is faulty. Replace the motor relay PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2111 |
| Description: | Developer motor start-up error |
| Causes: | The developer motor is not in the steady state within 3s after start-up |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer motor - Engine PWB 3 Checking drive unit 1 Drive unit 1 is not attached properly, or it is faulty. Execute U030[DLP] and check if the gear in drive unit 1 rotates normally. If there is a load in rotation, clean the gear and bushing and apply grease. If not repaired, replace drive unit 1 4 Checking the developer motor The developer motor is not properly attached, or it is faulty. Reattach the developer motor and execute U030[DLP]. If not operating normally, replace it. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB and then execute U411 [Table(ChartA)]. |
| Error code: | C2112 |
| Description: | Developer motor CMY Startup error (DC brushless) |
| Causes: | The steady signal does not turns on for 2s continuously after developer motor C/M/Y started up. |
| Remedy: | 1 Replacing the gear The gear does not rotate properly Replace the developer unit drive gear if it is faulty 2 Replacing the developer unit The developer roller does not rotate properly Check if the developer roller rotates, and replace the developer unit C/M/Y if not rotating 3 Checking the drive parts The drive parts do not operate properly Execute U030 [DLP(CMY)] to check if the developer motor C/M/Y drive gear rotates or has excessive load. Apply grease and repair the parts 4 Checking the connection The connector is not connected properly. Or wires are faulty Re-insert the following connector of the wire If there is no conductivity, replace the wire. Developer motor C/M/Y - Engine PWB 5 Checking developer motor C/ M/Y The developer motor C/M/Y is not installed properly or is faulty Reattach the developer motor C/M/Y If not resolved, replace it 6 Updating the firmware Firmware version is not the latest. Upgrade the firmware to the latest version 7 Checking the Engine PWB The engine PWB is faulty Replace the engine PWB |
| Error code: | C2121 |
| Description: | Black developer drive motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency within 5 s when ASIC (U7) on the engine controller PCB has issued a motor activation signal to the black developer drive motor. • When the black developer drive motor continues to drive 20 minutes. |
| Causes: | Defective engine controller PCB. Defective black developer drive motor. Excessive torque for driving black developer. (Overloaded by a damaged gear.) Defective harness between engine controller PCB and main drive motor, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the black developer drive motor. Check if the black developer rotates smoothly. Check for broken gears. Replace if any. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C2122 |
| Description: | Color developers drive motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency within 5 s when ASIC (U8) on the engine controller PCB has issued a motor activation signal to the color developers drive motor. • When the color developers drive motor continues to drive 20 minutes. |
| Causes: | Defective engine controller PCB. Defective color developers drive motor. Excessive torque for driving color developers. (Overloaded by a damaged gear.) Defective harness between engine controller PCB and color developers drive motor, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the color developers drive motor. Check if the yellow, magenta, and cyan developers rotate smoothly. Check for broken gears. Replace if any. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C2340 |
| Description: | Fuser drive motor driving clock table error • An error has occurred in the driving clock table on the engine controller PCB that controls the fuser drive motor (a stepping motor). |
| Causes: | Defective engine controller PCB. |
| Remedy: | Replace the engine controller PCB and check for correct operation. |
| Error code: | C2500 |
| Description: | Feed motor error |
| Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
| Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
| Error code: | C2510 |
| Description: | Paper feed motor starting error • No FG (Frequency generation) pulse is entered within the predetermined period when ASIC (U8) on the engine controller PCB has issued a motor activation signal to the paper feed motor. |
| Causes: | Defective engine controller PCB. Defective paper feed motor. Excessive torque for driving paper feed unit. (Overloaded by a damaged gear.) Defective harness between engine controller PCB and paper feed motor, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the paper feed motor. Check if the paper feed unit rotates smoothly. Check for broken gears. Replace if any. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C2520 |
| Description: | Paper feed motor starting time-out • The FG (Frequency generation) pulse does not reach the correct frequency within 30 s when ASIC (U8) on the engine controller PCB has issued a motor activation signal to the paper feed motor. |
| Causes: | Defective engine controller PCB. Defective paper feed motor. Excessive torque for driving paper feed unit. (Overloaded by a damaged gear.) Defective harness between engine controller PCB and main paper feed, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the paper feed motor. Check if the paper feed unit rotates smoothly. Check for broken gears. Replace if any. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C3100 |
| Description: | Carriage error |
| Causes: | When turning the power on or finishing originals scan through the scanner, the alignment of the home position sensor (turning on / off the sensor) fails and the error is detected. Then, the error is detected twice continuously even the initial operation is executed. |
| Remedy: | 1 Unlocking the scanner mirror frame The scanner mirror frame is not unlocked. Unlock the scanner mirror frame (lamp unit assy). Unlocking the scanner mirror frame 2 Checking the scanner movement A load is applied to the scanner movement. Check the operation of the lamp by U073 or manually moving it. If there is an excess load, check if there are any foreign objects on the optical wire or optical wire drum and clean it. After that, apply grease on the scanner rail. Detaching and reattaching the scanner wires 3 Checking the scanner wires The scanner wires are dirty or come off. Clean and reattach the scanner wires. Detaching and reattaching the scanner wires 4 Checking the scanner motor The scanner motor is faulty. Reattach the scanner motor and reconnect the connector. If not repaired, replace it. 5 Checking the belt tension of the scanner motor A load is applied to the scanner movement since the belt tension is improper. Adjust the scanner motor belt tension properly. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Scanner motor - Engine PWB Wiring diagram 7 Checking the home position sensor The home position sensor is not properly attached. Reattach the home position sensor. 8 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Home position sensor - Engine PWB Wiring diagram 9 Replacing the home position sensor The home position sensor is faulty. Replace the home position sensor. 10 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3200 |
| Description: | LED lamp startup error |
| Causes: | The white reference data acquired by lighting the LED lamp at the initial operation does not reach the specified value. Or, the light amount detected by the CCD PWB is not enough. (2 or more LED lamps do not light. The light does not reach the CCD PWB due to condensation.) |
| Remedy: | 1 Checking the LED lamp The LED lamp does not light. Execute U061 [CCD] and check if the LED lamp is lit. If not, replace the lamp unit. After that, execute U411 [Table(ChartA)]. Detaching and reattaching the lamp unit 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB • LED PWB - CCD PWB Wiring diagram 3 Checking the mirror The mirror or lens is frosted due to condensation. Clean the mirrors. If the condensation at the scanner section is resolved naturally by opening the document processor or the platen cover, turn the power switch off and on. 4 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4000 |
| Description: | Polygon motor synchronization problem • The revolution does not reach the stable speed within 20 s of the START signal. |
| Causes: | Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PWB. |
| Remedy: | Poor contact in the polygon motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Check if 24 V DC is supplied to YC17-1 on the engine PWB. If not, replace the engine PWB. |
| Error code: | C4200 |
| Description: | BD steady-state problem • ASIC of the main PWB detects a BD error A for 4000 ms after the polygon motor rotation has been stabilized. |
| Causes: | Defective laser diode. Defective polygon motor. Defective main PWB. Poor contact in connector terminals. |
| Remedy: | Defective laser diode. Replace the laser scanner unit. Defective polygon motor. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. Poor contact in connector terminals. Check the connection of connector YC8 on the main PWB and the continuity across the connector terminals. Repair or replace if necessary. |
| Error code: | C5120 |
| Description: | Abnormal separation charger high voltage leak current • ASIC (U8) on the engine controller PCB has detected a excessive leakage current in the separation charger high voltage supply. |
| Causes: | Defective engine controller PCB. Defective separation charger high voltage unit. Defective harness between engine controller PCB and separation charger high voltage unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the separation charger high voltage unit. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C5300 |
| Description: | Cleaning lamp broken detection • The current at the correct level is not detected when ASIC (U8) on the engine controller PCB generates the signal to activate the cleaning lamp. |
| Causes: | Defective engine controller PCB. Defective drum unit (cleaning lamp or drum PCB). Defective harness between engine controller PCB and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the drum unit. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C6000 |
| Description: | IH heating error 1 |
| Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6010 |
| Description: | Abnormally high fuser thermistor temperature The fuser Abnormally high signal is detected for 60 s or more. |
| Causes: | Defective PWB. |
| Remedy: | Replace the power source PWB or engine PWB and check for correct operation. |
| Error code: | C6020 |
| Description: | Fuser center thermistor high temperature error |
| Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6030 |
| Description: | Fuser center thermistor broken |
| Causes: | The output from the fuser center thermistor is under 20°C / 68°F level during warm-up. Or, the temperature detected at the fuser center thermistor does not change for 10s after turning the fuser heater on. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6040 |
| Description: | Fuser heater error |
| Causes: | The fuser center thermistor outputs the abnormal value for 1s continuously. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6100 |
| Description: | Fuser heater broken (For the internal count) |
| Causes: | The fuser press thermistor temperature detected does not reach the control temperature within 480s after shifting to the low power mode. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6110 |
| Description: | Press/heat roller heating time-out 2 • The temperature on the press/heat toller does not reach the correct temperature within the predetermined period after self-diagnostic code 6100 is cleared. The period for detection is longer than the condition for self-diagnostics code 6100. |
| Causes: | Defective engine controller PCB. Defective lower fuser heater. Defective lower thermostat. Defective fuser PCB. Defective lower fuser thermistor, or fitting is not proper. Defective AC power source. (Abnormal low voltage) Defective harness between engine controller PCB and fuser unit, or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the fuser unit (lower fuser heater). Replace the fuser unit (lower thermostat). Replace the fuser unit (fuser PCB). Replace the fuser unit (upper fuser thermistor). Connect to the proper AC power source. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C6120 |
| Description: | Fuser press thermistor high temperature error |
| Causes: | The fuser press thermistor detects 210°C / 410°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6130 |
| Description: | Fuser press thermistor broken |
| Causes: | The detection temperature of the fuser press thermistor does not reach 30°C / 86°F within 60s since warm-up starts. |
| Remedy: | 1 Removing foreign material There are foreign objects between the fuser press thermistor and the press roller. Or, the foreign objects are adhered on the press roller. Remove foreign objects if any on the press roller. Then, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6140 |
| Description: | Lower fuser thermistor abnormal temperature detection • The temperature detection output from the lower fuser thermistor is out of the normal range. |
| Causes: | Defective engine controller PCB. Defective fuser PCB. Defective lower fuser thermistor, or fitting is not proper. Defective harness between engine controller PCB and fuser unit (lower fuser thermistor), or poor contact of the connector terminals. |
| Remedy: | Replace the engine controller PCB and check for correct operation. Replace the fuser unit (fuser PCB). Replace the fuser unit (lower fuser thermistor). Check the continuity of the harness and the insertion of connectors. |
| Error code: | C6430 |
| Description: | Oil roller unit fuse break error • The engine controller PCB is not able to cut the fuse on the oil roller unit. |
| Causes: | Defective oil roller unit fuse. Defective harness between engine controller PCB and oil roller unit detection sensor, or poor contact of the connector terminals. |
| Remedy: | Replace the oil roller unit. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C7001 |
| Description: | Toner motor error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Toner motor - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7002 |
| Description: | Toner motor C error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor C - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7003 |
| Description: | Toner motor M error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor M - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7004 |
| Description: | Toner motor Y error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner motor Y - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7101 |
| Description: | Toner sensor error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The drive gears for the developer unit are damaged. (The spiral cannot rotate.) Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7102 |
| Description: | Toner sensor C error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7103 |
| Description: | Toner sensor M error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7104 |
| Description: | Toner sensor Y error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. (Go to the next step.) Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The developer spiral does not rotate since the drive gear is faulty. Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7301 |
| Description: | Toner hopper motor error |
| Causes: | It occurs 15 times continuously that the screw sensor does not detect the pulse for 200ms when driving the toner hopper motor. |
| Remedy: | 1 Checking the toner hopper motor The toner hopper motor is faulty. Execute U135 [Hopper] and check the toner hopper motor operation. (Go to the next step.) Executing U135 2 Checking the toner hopper drive section The toner hopper screw does not properly rotate due to excessive load. (The pulse plate does not rotate.) Rotate the toner hopper screw manually. Then, check if toner is not clogged in the toner hopper, and clean inside the toner hopper if necessary. Detaching and reattaching the inner unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner hopper motor - Front PWB• Screw sensor - Front PWB?• Front PWB - Engine PWB 4 Checking the screw sensor The screw sensor is faulty. Reattach the screw sensor. If not repaired, replace the sensor. 5 Replacing the drive parts The drive transmission from the toner hopper motor is faulty. Reattach the drive gears or the toner hopper motor. If not repaired, replace the parts faulty in operation. Or, replace the inner unit. Detaching and reattaching the inner unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7600 |
| Description: | Image density sensor detection error • The measured value at the end of color compensation is 255 or more for no image and LED off or the measured value for no image and LED on exceeds the value for any image. |
| Causes: | Defective engine controller PCB. Defective imege density sensor. |
| Remedy: | Replace the primary transfer unit. Check to see if the image density sensor is properly connected. |
| Error code: | C7610 |
| Description: | Image density sensor detection error • The measurement result of each density batch at the end of color compensation shows abnormal relation of density in size. |
| Causes: | Defective engine controller PCB. Defective imege density sensor. |
| Remedy: | Check the drum unit, high voltage unit, developing unit, and transfer unit. If any problem is found, replace the unit. |
| Error code: | C7700 |
| Description: | Offset drum sensor detection timeout error • When the drum home position is to be detected, the input level from the offset drum sensor to ASIC (U7) of the engine controller PCB has been gone hign for 5 seconds. |
| Causes: | Defective drum PCB. Defective engine controller PCB. Defective harness between engine controller PCB and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the drum unit. Replace the engine controller PCB. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C7710 |
| Description: | Offset drum sensor detection error • When the drum home position is to be detected, the input level from the offset drum sensor to ASIC (U7) of the engine controller PCB has been gone low for 4 seconds. |
| Causes: | Defective drum PCB. Defective engine controller PCB. Defective harness between engine controller PCB and drum unit, or poor contact of the connector terminals. |
| Remedy: | Replace the drum unit. Replace the engine controller PCB. Check the continuity of the harness and the insertion of connectors. |
| Error code: | C7800 |
| Description: | Outer thermistor broken (For the internal count) |
| Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7810 |
| Description: | Short-circuited external thermistor • The thermistor input value is 0.5 V or less. |
| Causes: | Poor contact in the connector terminals. Defective humidity sensor. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC13 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective humidity sensor. Replace the humidity sensor. Defective engine PWB. Replace the engine PWB. |
| Error code: | C8000 |
| Description: | Fnisher type mismatch problem • Absence of the finisher is detected. |
| Causes: | Different type of the finisher is installed. |
| Remedy: | Install the correct finisher. |
| Error code: | C8010 |
| Description: | Punch motor error 1 Object: 4000-sheet finisher + Punch unit |
| Causes: | 1. The punch home position sensor does not turn on when passing 200ms after driving the punch motor. 2. The pulse plate does not count the specified pulse when passing 300ms after the punch operation starts. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • Punch home position sensor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. 5 Checking the punch home position sensor The punch home position sensor is not properly attached or faulty. Execute U241 [Punch] > [Punch HP]. If the PH home position sensor does not properly operate, reattach it. If not repaired, replace the sensor. Executing U241 6 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 7 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8030 |
| Description: | Punch motor error 3 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position detection does not turn off within 50ms when initializing the home position. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8140 |
| Description: | Main tray error 1 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8170 |
| Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
| Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
| Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8180 |
| Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
| Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
| Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8210 |
| Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8220 |
| Description: | Document finisher* front clincher problem • During initialization, the front clincher is not detected in the home position within 500 ms after the front clincher returns to the home position. JAM90 is indicated the first time this problem occurs. If the problem occurs after initialization when the front cover is opened and closed, the problem is in the front clincher. • When the front clincher is operated from the home position, the front clincher home position sensor does not turn off within 500 ms. |
| Causes: | Loose connection of the front clincher motor connector. Malfunction of the front clincher motor. Malfunction of the front clincher home position sensor. Loose connection of the front clincher home position sensor connector. Defective finisher main PWB. |
| Remedy: | Loose connection of the front clincher motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Malfunction of the front clincher motor. Replace the front clincher motor and check for correct operation. Malfunction of the front clincher home position sensor. Replace the front clincher home position sensor and check for correct operation. Loose connection of the front clincher home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
