Brother MFC-9450CDN

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

35000

Скорость печати A4

Цветность печати

цветная

Общие характеристики
Тип устройства	МФУ
Сканер
Копир
Факс
Телефон
Печать фотографий
Цветность печати	цветная
Макс. формат	A4
Размещение	настольный
Число страниц в месяц	35 000
Область применения	малый офис
Технология печати	лазерная
Тип	лазерный/светодиодный
Принтер
Двусторонняя печать
Прямая печать
Печать без полей
Пигментные чернила
Количество цветов	4
Макс, разрешение для ч/б печати
По Y	600
По X	2 400
Скорость ч/б печати
A4	20
Копир
Шаг масштабирования	0,01
Макс, количество копий за цикл	99
Значение масштаба
Максимальное	4
Минимальное	0,25
Макс, разрешение (ч/б)
По X	1 200
По Y	600
Скорость цветного копирования
A4	16
Сканер
Макс. формат оригинала	A4
Емкость устройства автоподачи оригиналов	35
Тип сканера	планшетный/протяжный
Стандарт TWAIN
Стандарт WIA
Отправка изображения по e-mail
Оттенки серого	256
Тип датчика сканера	контактный (CIS)
Глубина цвета	48 бит
Макс, размер сканирования
По Y	356
По X	216
Разрешение сканера
По Х	1 200
По Y (улучшенное)	19 200
По Y	2 400
По Х (улучшенное)	19 200
Расходные материалы
Ресурс фотобарабана	17 000
Количество картриджей	4
Ресурс цветного картриджа/тонера	1 500
Ресурс ч/б картриджа/тонера	2 500
Печать на:
CD/DVD
Рулоне
Карточках
Пленках
Матовой бумаге
Этикетках
Конвертах
Глянцевой бумаге
Плотность бумаги
Минимальная	60
Максимальная	163
Факс
Память	500
Цветной
PC Fax
Макс, скорость передачи данных	33,6 Кбит/с
Телефон
Спикерфон
Проводная трубка
Беспроводная трубка
АОН
Caller ID
Автоответчик
Стандарт DECT
Языки управления
PostScript 3
PDF
PCL 6
PostScript
PCL 5e
PPDS
PCL 5c
PostScript 2
Лотки
Емкость лотка ручной подачи	50
Подача бумаги
Максимальная	800
Стандартная	300
Вывод бумаги
Стандартный	150
Финишер
Брошюровщик
Сортер
Степлер
Интерфейсы
Версия USB	2,0
RS-232
Устройство для чтения карт памяти
FireWire (IEEE 1394)
Wi-Fi
Bluetooth
LPT
Инфракрасный порт
Ethernet (RJ-45)
USB
Память/Процессор
Макс, объем памяти	576
Объем памяти	64
Дополнительная информация
Работа от аккумулятора
Экран
Поддержка ОС
Windows
Linux
Mac OS
Потребляемая мощность
При работе	495
В режиме ожидания	28
Габариты
Вес	39,9
Высота	716
Глубина	614
Ширина	566

Модули

DRIVE

ADF2

Детали DRIVE

Деталь:	Cover, HIP (M880)
Парткод:	087320616

Коды ошибок

D0...DF

Деталь:	Ось узла захвата бумаги в автоподатчике документов
Парткод:	LF6579001
Цена:	1 300 ₽

Деталь:	Ролик подачи бумаги в автоподатчике документов
Парткод:	LF6577001
Цена:	1 700 ₽

Деталь:	Узел отделения бумаги в автоподатчике документов, в сборе
Парткод:	LP2601001
Цена:	2 200 ₽

Error code:	20
Description:	Vertical image or label drift
Causes:	The printer is using non-continuous labels but is configured in continuous mode. The media sensor is positioned incorrectly. The media sensor is calibrated improperly. The platen roller is dirty. Improper printhead pressure settings (toggles). Improperly loaded ribbon or media. Incompatible media.
Remedy:	Configure the printer for non-continuous and run calibration routine, if necessary. Ensure that the media sensor is properly positioned to read a single/consistent interlabel gap. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Clean the platen roller. See Clean the Printhead and Platen Roller on page 131. Adjust the printhead pressure to ensure proper functionality. Verify that the printer is loaded properly. Ensure that the interlabel gaps or notches are 2 to 4 mm and consistently placed. Media must not exceed minimum specifications for mode of operation.

Error code:	21
Description:	The bar code printed on a label does not scan.
Causes:	The bar code is not within specifications because the print is too light or too dark. Not enough blank space around the bar code.
Remedy:	Perform the FEED Self Test on page 120. Adjust the darkness or print speed settings as necessary. Leave at least 1/8 in. (3.2 mm) between the bar code and other printed areas on the label and between the bar code and the edge of the label.

Error code:	22
Description:	Loss of printing registration on labels. Excessive vertical drift in top-of-form registration.
Causes:	The platen roller is dirty. Media guides are positioned improperly. The media type is set incorrectly. The media is loaded incorrectly.
Remedy:	Clean the platen roller according to the instructions in Clean the Printhead and Platen Roller on page 131. Ensure that the media guides are properly positioned. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81. Load media correctly. See Load Media on page 58.

Error code:	23
Description:	Auto Calibrate failed.
Causes:	Media or ribbon is loaded incorrectly. The sensors could not detect the media or ribbon. The sensors are dirty or positioned improperly. The sensors are dirty, or media is positioned improperly for the sensors to detect. The media type is set incorrectly.
Remedy:	Ensure that media and ribbon are loaded correctly. Manually calibrate the printer. See Calibrate Media and Ribbon Sensor Sensitivity on page 90. Ensure that the sensors are clean and that media is positioned properly. Set the printer for the correct media type (gap/notch, continuous, or mark). See Set Media Type on page 81.

Error code:	25
Description:	A label format was sent to the printer. Several labels print, then the printer skips, misplaces, misses, or distorts the image on the label.
Causes:	The serial communication settings are incorrect.
Remedy:	Ensure that the flow control settings match. Check the communication cable length. See Table 5 on page 48 for requirements. Check the printer driver or software communications settings (if applicable).

Error code:	26
Description:	A label format was sent to the printer but was not recognized. The DATA light flashes but no printing occurs.
Causes:	The prefix and delimiter characters set in the printer do not match the ones in the label format. Incorrect data is being sent to the printer.
Remedy:	Verify the prefix and delimiter characters. See Set Format Prefix Character on page 94 and Set Delimiter Character on page 95 for the requirements. Check the communication settings on the computer. Ensure that they match the printer settings. If the problem continues, check the label format.

Error code:	27
Description:	Broken or melted ribbon
Causes:	Darkness setting too high.
Remedy:	1. Reduce the darkness setting. 2. Clean the printhead thoroughly.

Error code:	28
Description:	The printer does not detect when the ribbon runs out. In thermal transfer mode, the printer did not detect the ribbon even though it is loaded correctly.
Causes:	The ribbon-out threshold is set too high to detect the ribbon. On a sensor profile, the ribbon-out threshold (circled in Figure 15) appears above the black bars that indicate the ribbon. This happens if you calibrate the printer without ribbon and later insert ribbon without recalibrating the printer or loading printer defaults.
Remedy:	1. Print a sensor profile (see Print Sensor Profile on page 89), and note the location of the ribbon-out threshold (circled in Figure 15). 2. Calibrate the printer, this time using ribbon, or load printer defaults. See Calibrate Media and Ribbon Sensor Sensitivity on page 90 or LOAD DEFAULTS on page 73. Important • Loading defaults resets all printer parameters back to factory defaults. 3. Print another sensor profile, and compare it to the first one. 4. If the ribbon-out threshold is still too high, you may manually change the value.

Error code:	29
Description:	The ribbon light is on even though ribbon is loaded correctly.
Causes:	The printer was not calibrated for the label and ribbon being used.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90.

Error code:	2A
Display:	No Ink Cartridge
Description:	Faulty NVRAM Data
Causes:	NVRAM PWB-A (Engine Control Board)
Remedy:	1 Unplug the power cord and plug it in, then turn OFF and ON the Power Switch. 2 Check NVRAM (PJ26) on PWB-A for proper connection and correct as necessary. 3 Change PWB-A.

Error code:	2E
Display:	Unable to print 2E
Description:	Unable to communicate with the Ink cartridge IC chip. (On the main unit side)
Causes:	1 Toner/New sensor PCB failure. 2 Engine PCB failure. 3 High-voltage power supply PCB failure. 4 Main PCB failure
Remedy:	1 Main PCB defective Replace the Main PCB ASSY.

Error code:	2F
Display:	Close Ink Cover
Description:	The Ink cartridge cover sensor detected an opened cover.
Remedy:	<User Check> - Close the Ink cartridge cover. 1 Ink cartridge cover sensor harness connection failure Reconnect the Ink cartridge cover sensor harness. 2 Damaged Ink cartridge cover Replace the Ink cartridge cover. 3 Ink cartridge cover sensor defective Replace the Ink cartridge cover sensor ASSY. 4 Main PCB defective Replace the Main PCB ASSY.

Error code:	30
Description:	The LCD displays a language that I cannot read
Causes:	The language parameter was changed through the control panel or a firmware command.
Remedy:	1. Press SETUP/EXIT to enter configuration mode. 2. Press MINUS (-). The printer displays the LANGUAGE parameter in the current language. Even if you cannot recognize the characters displayed, you can still scroll to another language. 3. Press SELECT to select the parameter. 4. Press PLUS (+) or MINUS (-) to scroll through the choices until you find a language that you can read. 5. Press SETUP/EXIT. The LCD displays SAVE CHANGES in the original language. 6. Press SETUP/EXIT again to exit configuration mode and save the changes (if the language does not change, you may need to scroll to a different save option by pressing PLUS (+) or MINUS (-) in the previous step). 7. Repeat this process, if necessary, until you reach the desired language.

Error code:	3D
Description:	EEPROM reading error (Not applicable)

Error code:	50
Display:	Tray 2 Paper Empty
Description:	Fuser Fan Failure The Fuser Fan rotation signal indicates to the Engine Control Board that the fan is no longer operational.
Causes:	• Fuser Fan, PL5.3.31 • FAN/PHD/MOT Harness, PL10.1.9 • Engine Control Board, PL9.1.16
Remedy:	1 Check the Fuser Fan for damage. Remove the Front Cover. Is the fan damaged? Replace the Fuser Fan. Go to Step 2. 2 Check the Fuser Fan connection. Is P/J482 connected to the harness? Go to Step 2. Reconnect the Fan. 3 Check orientation of the Fuser Fan. Does the Fan’s label face into the chute? Go to Step 3. Correct the installation. 4 Test the Fuser Fan. Run the Service Diagnostics Fuser Fan test. Does the Fan operate. Go to Step 6. Go to Step 5. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J48 and P/J482. 2. Check continuity between J48 <=> P483. Go to Step 5. Replace the FAN/PHD/MOT Harness. 6 Check the fan rotation signal. Print one sheet. Is there +3.3 V across P/J48-A12 <=> P/J48-A13? Replace the Engine Control Board. Replace the Fuser Fan.

Error code:	51
Display:	Send Error (DNS)
Description:	Rear Fan Failure The Rear Fan rotation signal indicates the fan is no longer operational.
Causes:	• Rear Fan, PL1.1.19 • LVPS, PL9.1.6 • Engine Control Board, PL9.1.16 • LV Harness, PL10.1.2
Remedy:	1 Check the Rear Fan for damage. Remove the Rear Cover. Is the fan damaged? Replace the Rear Fan. Go to Step 2. 2 Check the Rear Fan connection. Is P/J166 connected to the harness? Go to Step 3. Connect the Fan. 3 Check orientation of the Rear Fan. Does the Fan’s label face inwards? Go to Step 4. Correct the installation. 4 Test the Rear Fan. Run the Service Diagnostics Rear Fan test. Does the fan operate? Go to Step 6. Go to Step 5. 5 Check for +24 V to the fan. Disconnect P/J166. Is there +24 V across P166-1 <=> P166-3? Replace the Rear Fan. Replace the LVPS. 6 Check the fan rotation signal to the LVPS. Print one sheet. Is there +3.3 V between P/J166-1 <=> P/J166-3? Replace the Fuser Fan. Go to Step 7. 7 Check the rotation signal from the LVPS. Print one sheet. Is there +3.3 V between P/J165-15 <=> P/J165-3? Replace the LVPS. Go to Step 8. 8 Check the fan rotation signal at the Engine Control Board. Print one sheet. Is there +3.3 V between P/J61-4 <=> P/J61-16? Replace the LV Harness Replace the Engine Control Board.

Error code:	31
Description:	The LCD is missing characters or parts of characters
Causes:	The LCD may need replacing.
Remedy:	Run the Power-On Self Test on page 117 and check that the LCD display shows all characters. If not, replace the LCD.

Error code:	32
Description:	Changes in parameter settings did not take effect
Causes:	Parameters are set incorrectly. A command turned off the ability to change the parameter. A command changed the parameter back to the previous setting. If the problem continues, there may be a problem with the main logic board.
Remedy:	1. Set parameters and save permanently. 2. Turn the printer off (O) and then on (I). Refer to the ZPL Programming Guide. Refer to the ZPL Programming Guide. Replace the main logic board.

Error code:	33
Description:	The printer fails to calibrate or detect the top of the label.
Causes:	The printer was not calibrated for the label being used. The printer is configured for continuous media. The driver or software configuration is not set correctly.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81. Driver or software settings produce commands that can overwrite the printer configuration. Check the driver or software media-related setting.

Error code:	34
Description:	Non-continuous labels are being treated as continuous labels.
Causes:	The printer was not calibrated for the media being used. The printer is configured for continuous media.
Remedy:	Perform the calibration procedure in Calibrate Media and Ribbon Sensor Sensitivity on page 90. Set the media type to noncontinuous media. See Set Media Type on page 81.

Error code:	35
Description:	All lights are on, but nothing displays on the LCD, and the printer locks up.
Causes:	Internal electronic or firmware failure.
Remedy:	Turn the printer power off (O) and then on (I). If the printer locks up again, replace the main logic board.

Error code:	36
Description:	The printer locks up while running the Power-On Self Test.
Causes:	Main logic board failure.
Remedy:	Replace the main logic board.

Error code:	3A
Description:	Engine PCB transfer error. (Communication error between the main CPU and sub CPU.)
Causes:	1 Harness connection failure between engine PCB and main PCB. 2 Engine PCB failure. 3 Main PCB failure.
Remedy:	1 Harness connection failure between engine PCB and main PCB Check the harness connection between the engine PCB ASSY and main PCB ASSY, and reconnect it. 2 Engine PCB failure Replace the engine PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Error code:	3B
Display:	Unable to print 3B
Description:	Main PCB RAM failure
Causes:	Main PCB failure
Remedy:	Replace the main PCB ASSY.

Error code:	3F
Display:	Unable to print 3F
Description:	Carriage motor cannot stop.
Causes:	1 Engine PCB failure. 2 Main PCB failure.
Remedy:	<User Check> - Release the release lever at the back of the Paper tray and remove the jammed recording paper from the Engine part. 1 Carriage motor harness connection failure Reconnect the Carriage motor harness. 2 CR encoder strip stained Clean the CR encoder strip. 3 CR encoder strip defective Replace the CR encoder strip. 4 CR encoder sensor defective Replace the Carriage PCB ASSY. 5 Carriage motor defective Replace the Carriage motor ASSY. 6 Main PCB defective Replace the Main PCB ASSY.

Error code:	52
Display:	Send Error (POP3)
Description:	Fan Failure One of the two fans has failed resulting in a fatal error.
Causes:	• Rear Fan, PL1.1.19 • Fuser Fan, PL5.3.31
Remedy:	1 Check the fans for damage or debris: • Fuser Fan, PL1.1.19 • Rear Fan, PL5.3.31 Is either fan damaged? Replace the defective fan. Go to Step 3. 2 Replace the defective fan. Does the error persist? Go to Step 3 Complete 3 Test the fans. Run the Service Diagnostics fan tests to isolate the defective fan. Did one of the fans fail? Go to the troubleshooting procedure for the specific fan. If both fans pass, replace the Engine Control Board.

Brother MFC-9450CDN

Общие характеристики

Тип устройства

Сканер

Копир

Факс

Телефон

Печать фотографий

Цветность печати

Макс. формат

Размещение

Число страниц в месяц

Область применения

Технология печати

Тип

Принтер

Двусторонняя печать

Прямая печать

Печать без полей

Пигментные чернила

Количество цветов

Макс, разрешение для ч/б печати

Скорость ч/б печати

Копир

Шаг масштабирования

Макс, количество копий за цикл

Значение масштаба

Макс, разрешение (ч/б)

Скорость цветного копирования

Сканер

Макс. формат оригинала

Емкость устройства автоподачи оригиналов

Тип сканера

Стандарт TWAIN

Стандарт WIA

Отправка изображения по e-mail

Оттенки серого

Тип датчика сканера

Глубина цвета

Макс, размер сканирования

Разрешение сканера

Расходные материалы

Ресурс фотобарабана

Количество картриджей

Ресурс цветного картриджа/тонера

Ресурс ч/б картриджа/тонера

Печать на:

Плотность бумаги

Факс

Память

Цветной

PC Fax

Макс, скорость передачи данных

Телефон

Спикерфон

Проводная трубка

Беспроводная трубка

АОН

Caller ID

Автоответчик

Стандарт DECT

Языки управления

Лотки

Емкость лотка ручной подачи

Подача бумаги

Вывод бумаги

Финишер

Брошюровщик

Сортер

Степлер

Интерфейсы

Версия USB

RS-232

Устройство для чтения карт памяти

FireWire (IEEE 1394)

Wi-Fi

Bluetooth

LPT

Инфракрасный порт

Ethernet (RJ-45)

Error code:	53
Display:	Send Error (SMTP)
Description:	The password did not match in a relay or mailbox transmission, and the transmission ended in failure.
Causes:	· Loose cable connection · Defective controller fan · Defective IOD1 board · Defective MCTL board
Remedy:	Confirm that both parties are using the same system password and the both units are compatible. Then, ask the remote party to transmit again.

Error code:	54
Display:	Send Error (Wrong Config)
Description:	10-398 ERROR 54 FAN FAILURE
Causes:	· Loose cable connection · Defective ozone fan · Defective IOD2 board · Defective MCTL board
Remedy:	Enter Service Diagnostics Mode. Run the “Fuser Fan” test. Does the Fuser Fan operate? Y↓N→ Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-1 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-4 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-3 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the Fuser Fan. Replace the Fuser Fan Assembly. Remove the Rear Cover, Rear Shield and the Rear Shield Bracket. Measure the voltage between P530-5 on the Engine Control Board and frame ground. Does the voltage measure +24 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-8 on the Engine Control Board and frame ground. Does the voltage measure 0 VDC? Y↓N→ Replace the Engine Control Interface Board. Measure the voltage between P530-7 on the Engine Control Board and frame ground. Does the voltage measure +5 VDC? Y↓N→ Replace the Engine Control Board. If the problem persists, repair or replace the harness between Engine Control Board and the +24 VDC LVPS Fan. Replace the +24 VDC LVPS Fan.

Error code:	55
Display:	[Stop Pressed]
Description:	Stop/Clear has been pressed during a fax transmission.
Causes:	· Loose cable connection · Defective fusing unit fan · Defective IOD1 board · Defective MCTL board
Remedy:	Try again.

Error code:	56
Display:	Toner Empty
Description:	The toner cartridge has run out. The machine stops printing.
Causes:	Harness connection failure of back cover switch ASSY. Eject actuator failure. Eject sensor PCB ASSY failure. Main PCB failure
Remedy:	Replace the toner cartridge with a new one.

Error code:	57
Display:	Toner Low
Description:	The toner cartridge is almost empty.
Remedy:	Take out the toner cartridge and thoroughly shake it. By doing this, you can temporarily reestablish printing operations.

Error code:	58
Display:	Tray 1 Paper Empty
Description:	There is no paper in the tray 1.
Causes:	Harness connection failure between fuser unit and eject sensor PCB. Fuser unit failure. LVPS PCB failure. Eject sensor PCB ASSY failure. Main PCB failure
Remedy:	Load paper in the tray 1.

Error code:	5A
Display:	Unable to print 5A
Description:	HVPS PCB failure (Developing bias voltage failure)
Causes:	HVPS PCB ASSY harness connection failure. HVPS PCB failure. Main PCB failure
Remedy:	1 HVPS PCB ASSY harness connection failure Check the harness connection between the HVPS PCB and main PCB. Then, reconnect them. 2 HVPS PCB failure Replace the HVPS PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Error code:	5E
Display:	Unable to print 5E
Description:	Overcurrent protection was activated in the driver IC during Maintenance unit pump operation.
Causes:	The driving current has exceeded the limit due to an abnormal load applied to the maintenance unit.
Remedy:	1 Foreign materials in the Maintenance unit part Remove foreign materials. 2 Maintenance unit defective Replace the Maintenance unit. 3 Main PCB defective Replace the Main PCB ASSY.

Error code:	5F
Description:	The waste toner box near full. (The sensor detected that thewaste toner became near full.)
Causes:	1 Harness connection failure of waste toner sensor. 2 Waste toner sensor failure. 3 High-voltage power supply PCB failure. 4 Main PCB failure.
Remedy:	1 Harness connection failure of waste toner sensor Check the harness connection of the waste toner sensor and reconnect it. 2 Waste toner sensor failure Check the sensor performance following the procedure described in “Function code 32”. If any problem occurs, replace the waste toner sensor. 3 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

Error code:	60
Display:	Nongenuine Toner
Description:	Imaging Unit Motor Failure, Code 60
Causes:	• Imaging Unit Drive Motor • Engine Control Board
Remedy:	1 1. Enter service diagnostics and run the Imaging Unit Motor test. 2. Does the motor operate correctly? Go to step 7. Go to step 2. 2 1. Is the voltage at J210-5 +5 VDC? Go to step 3. Replace the engine control board. 3 1. Is the voltage at J210-7 +24 VDC? Go to step 4. Use the +24 VDC wirenets to troubleshoot and resolve the missing voltage. 4 1. Enter service diagnostics. 2. While running the Imaging Unit Motor test, check the voltage at J210-1 and J210-2. 3. Is the voltage 0 VDC while the test is running? Go to step 5. Replace the engine control board. 5 Is the frequency between J210-4 and ground between 1 KHz and 1.3 KHz? Replace the imaging unit drive motor. Go to step 6. 6 1. Check for a short to ground at J210-4. 2. Is the wire grounded? Repair or replace the wiring harness. Replace the engine control board. 7 1. Enter service diagnostics. 2. While running the Imaging Unit Motor test, check the voltage at J210-9. 3. Is the voltage +5 VDC while the test is running? Replace the imaging unit drive motor. Replace the engine control board.