Kyocera TASKalfa 1801
Рейтинг
Актуальный
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A3
Число страниц в месяц
30000
Цветность печати
черно-белая
Общие характеристики |
|
|---|---|
Цветность печати |
|
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Печать фотографий |
|
Телефон |
|
Размещение |
настольный |
Число страниц в месяц |
30 000 |
Область применения |
малый офис |
Макс. формат |
A3 |
Тип устройства |
МФУ |
Копир |
|
Сканер |
|
Факс |
|
Принтер |
|
Печать без полей |
|
Прямая печать |
|
Система непрерывной подачи чернил |
|
Двусторонняя печать |
|
Пигментные чернила |
|
Время разогрева |
18,8 |
Макс, разрешение для ч/б печати |
|
| По Y | 600 |
| По X | 600 |
Скорость цветной печати |
|
| A3 | 8 |
Время выхода первого отпечатка |
|
| Ч/б | 5,7 |
Копир |
|
Макс, количество копий за цикл |
999 |
Шаг масштабирования |
0,01 |
Значение масштаба |
|
| Максимальное | 4 |
| Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
| По X | 200 |
| По Y | 600 |
| По X | 600 |
Скорость ч/б копирования |
|
| A4 | 18 |
Сканер |
|
Макс. формат оригинала |
A3 |
Слайд-адаптер |
|
Отправка изображения по e-mail |
|
Стандарт WIA |
|
Тип сканера |
планшетный/протяжный |
Оттенки серого |
256 |
Стандарт TWAIN |
|
Макс, размер сканирования |
|
| По Y | 420 |
| По X | 297 |
Разрешение сканера |
|
| По Х | 600 |
| По Y | 400 |
Скорость сканирования |
|
| Цветн, | 22 |
| Ч/б | 22 |
Расходные материалы |
|
Ресурс ч/б картриджа/тонера |
15 000 |
Количество картриджей |
1 |
Ресурс фотобарабана |
150 000 |
Печать на: |
|
| CD/DVD |
|
| Фотобумаге |
|
| Рулоне |
|
| Матовой бумаге |
|
| Глянцевой бумаге |
|
| Карточках |
|
| Пленках |
|
| Этикетках |
|
| Конвертах |
|
Плотность бумаги |
|
| Максимальная | 160 |
| Минимальная | 45 |
Факс |
|
Цветной |
|
PC Fax |
|
Макс, скорость передачи данных |
33,6 Кбит/с |
Телефон |
|
Caller ID |
|
Беспроводная трубка |
|
Автоответчик |
|
Стандарт DECT |
|
АОН |
|
Спикерфон |
|
Проводная трубка |
|
Языки управления |
|
| PCL 5e |
|
| PCL 5c |
|
| PostScript 3 |
|
| PCL 6 |
|
| PPDS |
|
|
|
|
| PostScript 2 |
|
| PostScript |
|
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
| Стандартная | 300 |
| Максимальная | 1 300 |
Вывод бумаги |
|
| Стандартный | 250 |
Финишер |
|
Степлер |
|
Электронная сортировка |
|
Сортировка со сдвигом |
|
Брошюровщик |
|
Сортер |
|
Интерфейсы |
|
Версия USB |
2,0 |
LPT |
|
Bluetooth |
|
Wi-Fi 802.11n |
|
Wi-Fi |
|
Инфракрасный порт |
|
AirPrint |
|
RS-232 |
|
Веб-интерфейс |
|
Устройство для чтения карт памяти |
|
FireWire (IEEE 1394) |
|
Ethernet (RJ-45) |
|
USB |
|
Количество слотов расширения |
1 |
Память/Процессор |
|
Процессор |
ARM v5 |
Частота процессора |
500 |
Объем памяти |
256 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Экран |
|
Поддержка ОС |
|
| Mac OS |
|
| DOS |
|
| Linux |
|
| Windows |
|
Потребляемая мощность |
|
| В режиме ожидания | 75 |
| При работе | 385 |
Уровень шума |
|
| При работе | 62 |
| В режиме ожидания | 40 |
Габариты |
|
Вес |
28 |
Ширина |
565 |
Глубина |
527 |
Высота |
485 |
Модули
Developer Section
ELECTRICAL COMPONENTS
Paper Feed Section 1
(Электронные компоненты)
PAPER FEED SECTION 2
Paper Conveying Section 2
(Узел переноса)
(Узел термозакрепления)
(Детали корпуса)
Image Formation Section
Operation Section(18ppm(F)/22ppm(F))
COVERS
PAPER CASSETTE
Operation Section(18ppm/22ppm)
Fuser Section
Paper Conveying Section 1
CASSETTE ASSEMBLY
FRAMES 1
FRAMES 2
Laser Scanner Section
SCANNER SECTION
DRIVE SECTION
Детали CASSETTE ASSEMBLY
| Деталь: | DV-4105 |
| Парткод: | 302NG93010 |
| Деталь: | PARTS HIGH VOLTAGE UNIT SP |
| Парткод: | 302NG94250 |
| Цена: | 5 500 ₽ |
| Деталь: | PARTS PWB MAIN ENGINE ASSY SP 18ppm/22ppm |
| Парткод: | 302NN94040 |
| Деталь: | PARTS PWB MAIN ENGINE ASSY EU SP 18ppm(F)/22ppm(F) |
| Парткод: | 302NG94320 |
| Деталь: | PARTS UNIT POWER SOURCE 230 SP |
| Парткод: | 302NG94240 |
| Деталь: | PARTS UNIT POWER SOURCE 120 SP |
| Парткод: | 302NG94230 |
| Деталь: | PROTECTOR LVU |
| Парткод: | 302NG02550 |
| Деталь: | WIRE PAPER |
| Парткод: | 302NG46050 |
| Деталь: | WIRE PF |
| Парткод: | 302NG46160 |
| Деталь: | WIRE HUMIDITY SENSOR |
| Парткод: | 302NG46130 |
| Деталь: | WIRE MAIN MOTOR |
| Парткод: | 302NG46040 |
| Деталь: | WIRE HEATER CONT |
| Парткод: | 302NG46170 |
| Деталь: | WIRE DP |
| Парткод: | 302NG46200 |
| Деталь: | WIRE FAN |
| Парткод: | 302NG46150 |
| Деталь: | SHIELD MAIN PWB |
| Парткод: | 302NG02290 |
| Деталь: | LID FAX BOARD |
| Парткод: | 302NG39020 |
| Деталь: | LID NETWORK BOARD |
| Парткод: | 302NG39030 |
| Деталь: | LID WIFI |
| Парткод: | 302NG39040 |
| Деталь: | MOUNT HVU UPPER |
| Парткод: | 302NG39010 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | +BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | FOOT |
| Парткод: | 302HN02611 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | WIRE MPF |
| Парткод: | 302NG46260 |
| Деталь: | ACTUATOR MPF |
| Парткод: | 302NG08170 |
| Деталь: | SPRING ACTUATOR MPF |
| Парткод: | 302NG08330 |
| Деталь: | PLATE LIFT MPF |
| Парткод: | 302NG08140 |
| Деталь: | ARM LIFT MPF |
| Парткод: | 302NG08130 |
| Деталь: | JOINT LIFT MPF |
| Парткод: | 302NG08190 |
| Деталь: | SPRING LIFT MPF |
| Парткод: | 302NG08150 |
| Деталь: | BUSH 8 |
| Парткод: | 302NG08250 |
| Деталь: | SHAFT MPF |
| Парткод: | 302NG08240 |
| Деталь: | PIN FEED ROLLER |
| Парткод: | 302NG08280 |
| Деталь: | SPRING MPF ROLLER |
| Парткод: | 302NG08320 |
| Деталь: | PARTS ROLLER MPF SP |
| Парткод: | 302NG94130 |
| Деталь: | GUIDE UPPER MPF |
| Парткод: | 302NG08210 |
| Деталь: | HOLDER RETARD |
| Парткод: | 302NG06200 |
| Деталь: | PARTS ROLLER RETARD ASSY SP |
| Парткод: | 302NG94110 |
| Деталь: | FRAME FEED LOW A |
| Парткод: | 302NG06020 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 302K306070 |
| Деталь: | FRAME FEED LOW B |
| Парткод: | 302NG06030 |
| Деталь: | SHEET FEED A |
| Парткод: | 302NG06210 |
| Деталь: | FRAME FEED UP |
| Парткод: | 302NG06010 |
| Деталь: | BUSH DRIVE 8 |
| Парткод: | 302K331230 |
| Деталь: | SHAFT DRIVE FEED |
| Парткод: | 302NG06040 |
| Деталь: | GUIDE FEED SIDE R |
| Парткод: | 302NG06090 |
| Деталь: | GUIDE FEED SIDE F |
| Парткод: | 302NG06060 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 302NG06170 |
| Деталь: | PULLEY GUIDE A |
| Парткод: | 2C907410 |
| Деталь: | GUIDE FEED UP |
| Парткод: | 302NG06100 |
| Деталь: | HOLDER FEED |
| Парткод: | 302NG06050 |
| Деталь: | GEAR FEED Z27 |
| Парткод: | 302NG06180 |
| Деталь: | SHAFT FEED L |
| Парткод: | 302NG06110 |
| Деталь: | GEAR FEED Z32 |
| Парткод: | 302NG06190 |
| Деталь: | PULLEY FEED ASSY |
| Парткод: | 302F906230 |
| Цена: | 750 ₽ |
| Деталь: | BUSH 4 |
| Парткод: | 302K306460 |
| Деталь: | SHAFT PICKUP |
| Парткод: | 302NG06140 |
| Деталь: | PARTS PULLEY PICKUP ASSY SP |
| Парткод: | 302NG94120 |
| Цена: | 700 ₽ |
| Деталь: | SPRING PICKUP |
| Парткод: | 302NG06130 |
| Деталь: | SPRING SEPARATION |
| Парткод: | 302NG08230 |
| Деталь: | PARTS PAD SEPARATION ASSY SP |
| Парткод: | 302NG94380 |
| Цена: | 1 100 ₽ |
| Деталь: | MOUNT SEPARATION |
| Парткод: | 302NG08310 |
| Деталь: | PARTS PRIMARY FEED ASSY SP |
| Парткод: | 302NG94020 |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-4105 |
| Цена: | 9 000 ₽ |
| Деталь: | ELA UNIT-TRANSFER |
| Парткод: | MC-4105 |
| Цена: | 4 900 ₽ |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | LK-4105 |
| Цена: | 9 500 ₽ |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | FK-4105 |
| Цена: | 13 500 ₽ |
| Деталь: | ROLLER-HEAT, ML-1660,AL5052,18.1,247.5 |
| Парткод: | HR-FK4105 |
| Цена: | 700 ₽ |
| Деталь: | ROLLER-PRESSURE, ML-1660,8,SUM22 or SUM23 |
| Парткод: | PR-FK4105 |
| Цена: | 1 300 ₽ |
| Деталь: | Крышка планшетного сканера (тип H) |
| Парткод: | 1202NG0UN0 |
| Деталь: | M.GLAZE R. 100MJ 1/2W |
| Парткод: | 7RHA2H10701+H01 |
| Деталь: | HOLDER CONVEYING F |
| Парткод: | 302NG24740 |
| Деталь: | SPRING EARTH REGIST B |
| Парткод: | 302NG24780 |
| Деталь: | SPRING EARTH REGIST C |
| Парткод: | 302NG24790 |
| Деталь: | SPRING EARTH REGIST D |
| Парткод: | 302NG24830 |
| Деталь: | SPRING EARTH REGIST A |
| Парткод: | 302NG24770 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | BUSH 8 |
| Парткод: | 302H024830 |
| Деталь: | PARTS ROLLER REGIST LEFT SP |
| Парткод: | 302NG94170 |
| Деталь: | GEAR REGIST L Z17L |
| Парткод: | 302NG24710 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GUIDE TRANSFER LEFT |
| Парткод: | 302NG24730 |
| Деталь: | RAIL CLEANER REGIST |
| Парткод: | 302NG24800 |
| Деталь: | SHEET REGIST L |
| Парткод: | 302NG24610 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | WIRE MPF |
| Парткод: | 302NG46260 |
| Деталь: | GUIDE FEED REGIST |
| Парткод: | 302NG24600 |
| Деталь: | ACTUATOR REGIST |
| Парткод: | 302NG24620 |
| Деталь: | SPRING ACTUATOR REGIST |
| Парткод: | 302NG24630 |
| Деталь: | CUSHION GUIDE FEED |
| Парткод: | 302NG24640 |
| Деталь: | GUIDE TRANSFER RIGHT |
| Парткод: | 302NG24320 |
| Деталь: | SPRING GUIDE TRANSFER |
| Парткод: | 302K324230 |
| Деталь: | GEAR TRANSFER Z18L |
| Парткод: | 302K324170 |
| Деталь: | COLLAR ROLLER |
| Парткод: | 302NG24350 |
| Деталь: | PARTS ROLLER TRANSFER SP |
| Парткод: | 302NG94150 |
| Деталь: | PARTS ROLLER TRANSFER U SP |
| Парткод: | 302NG94160 |
| Деталь: | ARM TRANSFER F |
| Парткод: | 302NG24390 |
| Деталь: | ARM TRANSFER R |
| Парткод: | 302NG24400 |
| Деталь: | BUSH TRANSFER ROLL R |
| Парткод: | 302K324430 |
| Деталь: | SPRING TRANSFER R |
| Парткод: | 302NG24370 |
| Деталь: | BUSH TRANSFER ROLL F |
| Парткод: | 302K324240 |
| Деталь: | SPRING TRANSFER F |
| Парткод: | 302NG24380 |
| Деталь: | HOLDER SEPARATION |
| Парткод: | 302NG24330 |
| Деталь: | PLATE SEPARATION |
| Парткод: | 302NG24340 |
| Деталь: | TERMINAL SEPARATION |
| Парткод: | 302NG24130 |
| Деталь: | TERMINAL TRANSFER |
| Парткод: | 302NG24150 |
| Деталь: | SHEET REGIST RIGHT F |
| Парткод: | 302NG24120 |
| Деталь: | SHEET REGIST RIGHT R |
| Парткод: | 302NG24140 |
| Деталь: | SHEET DU |
| Парткод: | 302NG24160 |
| Деталь: | SPRING REGIST F |
| Парткод: | 302K324200 |
| Деталь: | SPRING REGIST R |
| Парткод: | 302K324440 |
| Деталь: | GEAR REGIST R Z17R |
| Парткод: | 302NG24110 |
| Деталь: | BUSH REGIST F |
| Парткод: | 302K324180 |
| Деталь: | BUSH REGIST R |
| Парткод: | 302K324270 |
| Деталь: | BUSH REGIST C |
| Парткод: | 302NG24100 |
| Деталь: | SPRING REGIST C |
| Парткод: | 302NG24080 |
| Деталь: | PARTS ROLLER REGIST RIGHT SP |
| Парткод: | 302NG94140 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | LABEL A2 |
| Парткод: | 302NG34090 |
| Деталь: | SPRING DU FEED |
| Парткод: | 302K329030 |
| Деталь: | GUIDE DU |
| Парткод: | 302NG29010 |
| Деталь: | PULLEY DU |
| Парткод: | 302K329020 |
| Деталь: | LEVER CONVEYING R |
| Парткод: | 302NG24040 |
| Деталь: | SPRING CONVEYING R |
| Парткод: | 302K324360 |
| Деталь: | LEVER CONVEYING F |
| Парткод: | 302NG24030 |
| Деталь: | SPRING CONVEYING F |
| Парткод: | 302K324110 |
| Деталь: | BASE CONVEYING |
| Парткод: | 302NG24010 |
| Деталь: | GUIDE CONVEYING |
| Парткод: | 302NG24050 |
| Деталь: | SPRING EARTH CONVEYING |
| Парткод: | 302NG24090 |
| Деталь: | SHAFT RIGHT COVER F |
| Парткод: | 302K304550 |
| Деталь: | FILM CONVEYING SHAFT |
| Парткод: | 302K304630 |
| Деталь: | SHAFT RIGHT COVER R |
| Парткод: | 302NG04590 |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-4105 |
| Цена: | 9 000 ₽ |
| Деталь: | ELA UNIT-TRANSFER |
| Парткод: | MC-4105 |
| Цена: | 4 900 ₽ |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | LK-4105 |
| Цена: | 9 500 ₽ |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | FK-4105 |
| Цена: | 13 500 ₽ |
| Деталь: | ROLLER-HEAT, ML-1660,AL5052,18.1,247.5 |
| Парткод: | HR-FK4105 |
| Цена: | 700 ₽ |
| Деталь: | ROLLER-PRESSURE, ML-1660,8,SUM22 or SUM23 |
| Парткод: | PR-FK4105 |
| Цена: | 1 300 ₽ |
| Деталь: | Крышка планшетного сканера (тип H) |
| Парткод: | 1202NG0UN0 |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-4105 |
| Цена: | 9 000 ₽ |
| Деталь: | ELA UNIT-TRANSFER |
| Парткод: | MC-4105 |
| Цена: | 4 900 ₽ |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | LK-4105 |
| Цена: | 9 500 ₽ |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | FK-4105 |
| Цена: | 13 500 ₽ |
| Деталь: | ROLLER-HEAT, ML-1660,AL5052,18.1,247.5 |
| Парткод: | HR-FK4105 |
| Цена: | 700 ₽ |
| Деталь: | ROLLER-PRESSURE, ML-1660,8,SUM22 or SUM23 |
| Парткод: | PR-FK4105 |
| Цена: | 1 300 ₽ |
| Деталь: | Крышка планшетного сканера (тип H) |
| Парткод: | 1202NG0UN0 |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-4105 |
| Цена: | 9 000 ₽ |
| Деталь: | ELA UNIT-TRANSFER |
| Парткод: | MC-4105 |
| Цена: | 4 900 ₽ |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | LK-4105 |
| Цена: | 9 500 ₽ |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | FK-4105 |
| Цена: | 13 500 ₽ |
| Деталь: | ROLLER-HEAT, ML-1660,AL5052,18.1,247.5 |
| Парткод: | HR-FK4105 |
| Цена: | 700 ₽ |
| Деталь: | ROLLER-PRESSURE, ML-1660,8,SUM22 or SUM23 |
| Парткод: | PR-FK4105 |
| Цена: | 1 300 ₽ |
| Деталь: | Крышка планшетного сканера (тип H) |
| Парткод: | 1202NG0UN0 |
| Деталь: | MC-4105 |
| Парткод: | 302NG93050 |
| Деталь: | DISPOSAL TANK ASSY |
| Парткод: | 302NGJ0311 |
| Деталь: | +TP-CUP M SCREW 3X12 R |
| Парткод: | 7BB607312H |
| Деталь: | MK-4105/MAINTENANCE KIT |
| Парткод: | 1702NG0UN0 |
| Деталь: | COVER OPERATION |
| Парткод: | 302NG05010 |
| Деталь: | LENS LED OPERATION |
| Парткод: | 302NG05180 |
| Деталь: | KEY POWER SUPPLY |
| Парткод: | 302NG05060 |
| Деталь: | KEY LOGOUT INTERRUPT |
| Парткод: | 302NG05070 |
| Деталь: | KEY RESET |
| Парткод: | 302NG05050 |
| Деталь: | KEY STOP |
| Парткод: | 302NG05040 |
| Деталь: | KEY START |
| Парткод: | 302NG05030 |
| Деталь: | KEY 10 |
| Парткод: | 302NG05020 |
| Деталь: | KEY MENU |
| Парткод: | 302NG05080 |
| Деталь: | KEY CONTROL |
| Парткод: | 302NG05090 |
| Деталь: | KEY OK |
| Парткод: | 302NG05100 |
| Деталь: | KEY RETURN |
| Парткод: | 302NG05110 |
| Деталь: | KEY FUNCTION |
| Парткод: | 302NG05130 |
| Деталь: | KEY FUNCTION L |
| Парткод: | 302NG05140 |
| Деталь: | KEY SELECT |
| Парткод: | 302NG05120 |
| Деталь: | KEY FAX |
| Парткод: | 302NG05200 |
| Деталь: | SHEET SHIELD |
| Парткод: | 302NG05260 |
| Деталь: | PARTS PWB PANEL MAIN ASSY SP |
| Парткод: | 302NG94270 |
| Деталь: | SPRING OPERATION |
| Парткод: | 302NG05310 |
| Деталь: | COVER PANEL |
| Парткод: | 302NG05170 |
| Деталь: | LID OPERATION |
| Парткод: | 302NG05160 |
| Деталь: | LID OPERATION FAX |
| Парткод: | 302NG05220 |
| Деталь: | SHEET OPERATION |
| Парткод: | 302NG05190 |
| Деталь: | COVER FAX OPERATION |
| Парткод: | 302NG05210 |
| Деталь: | SHEET OPERATION DE |
| Парткод: | 302NG05320 |
| Деталь: | SHEET OPERATION FR |
| Парткод: | 302NG05330 |
| Деталь: | SHEET OPERATION IT |
| Парткод: | 302NG05340 |
| Деталь: | SHEET OPERATION ES |
| Парткод: | 302NG05350 |
| Деталь: | SHEET OPERATION PT |
| Парткод: | 302NG05360 |
| Деталь: | SHEET OPERATION NL |
| Парткод: | 302NG05370 |
| Деталь: | SHEET OPERATION RU |
| Парткод: | 302NG05380 |
| Деталь: | +BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | PARTS OPERATION UNIT SP |
| Парткод: | 302NG94070 |
| Деталь: | COVER MIDDLE REAR |
| Парткод: | 302NG04130 |
| Деталь: | COVER REAR |
| Парткод: | 302NG04140 |
| Деталь: | COVER EXIT UPPER |
| Парткод: | 302NG04230 |
| Деталь: | COVER EXIT REAR |
| Парткод: | 302NG04090 |
| Деталь: | COVER RIGHT FRONT |
| Парткод: | 302NG04040 |
| Деталь: | Cover Right Rear |
| Парткод: | 302NG04050 |
| Деталь: | COVER INNER |
| Парткод: | 302NG04170 |
| Деталь: | LEVER CONT RELEASE |
| Парткод: | 2BL04200 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 302NG12320 |
| Деталь: | WIRE DRUM CONNECT |
| Парткод: | 302NG46250 |
| Деталь: | PARTS PWB DRUM CONNECT ASSY SP |
| Парткод: | 302NG94290 |
| Деталь: | MOUNT MAIN SW |
| Парткод: | 302NG04200 |
| Деталь: | PARTS PWB SWITCH ASSY SP |
| Парткод: | 302NG94300 |
| Деталь: | HOLDER MAIN KEY |
| Парткод: | 302NG04210 |
| Деталь: | KEY POWER |
| Парткод: | 302NG04220 |
| Деталь: | COVER EXIT FRONT |
| Парткод: | 302NG04100 |
| Деталь: | COVER LEFT INNER |
| Парткод: | 302NG04080 |
| Деталь: | TRAY RIGHT |
| Парткод: | 302NG04110 |
| Деталь: | TRAY LEFT |
| Парткод: | 302NG04120 |
| Деталь: | COVER FRONT LEFT |
| Парткод: | 302NG04020 |
| Деталь: | PARTS CLEANER REGIST ASSY SP |
| Парткод: | 302NG94370 |
| Деталь: | LABEL ENERGY STAR |
| Парткод: | E302N434050 |
| Деталь: | STRAP FRONT COVER |
| Парткод: | E302NG04610 |
| Деталь: | COVER REAR PWB |
| Парткод: | 302NG04150 |
| Деталь: | SHIELD REAR PWB |
| Парткод: | 302NG04160 |
| Деталь: | COVER LEFT |
| Парткод: | 302NG04070 |
| Деталь: | LID DEVE WIRE |
| Парткод: | 302NG04190 |
| Деталь: | COVER FRONT RIGHT |
| Парткод: | 302NG04030 |
| Деталь: | COVER RIGHT UPPER |
| Парткод: | 302NG04060 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR(BLACK) |
| Парткод: | 7BB782308H |
| Деталь: | +BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | PARTS COVER FRONT ASSY SP |
| Парткод: | 302NG94010 |
| Деталь: | LEVER RELEASE BASE |
| Парткод: | 302NG09160 |
| Деталь: | PLATE SIDE SWITCH |
| Парткод: | 302NG09190 |
| Деталь: | SPRING SIDE SWITCH |
| Парткод: | 302K309220 |
| Деталь: | PAD CASSETTE |
| Парткод: | 2C907140 |
| Деталь: | SPRING RELEASE CURSOR |
| Парткод: | 302NG09180 |
| Деталь: | GEAR GUIDE SIDE |
| Парткод: | 302BM07410 |
| Деталь: | CASSETTE |
| Парткод: | 302NG09010 |
| Деталь: | BASE CASSETTE |
| Парткод: | 302NG09030 |
| Деталь: | CURSOR CASSETTE REAR |
| Парткод: | 302NG09050 |
| Деталь: | CURSOR CASSETTE FRONT |
| Парткод: | 302NG09040 |
| Деталь: | SPRING BOTTOM R |
| Парткод: | 302NG09080 |
| Деталь: | ARM SIZE DETECTION |
| Парткод: | 302NG09100 |
| Деталь: | LEVER RELEASE CURSOR |
| Парткод: | 302NG09170 |
| Деталь: | SPRING BOTTOM F |
| Парткод: | 302NG09070 |
| Деталь: | SPRING RELEASE BASE |
| Парткод: | 302NG09210 |
| Деталь: | CURSOR END |
| Парткод: | 302NG09060 |
| Деталь: | LABEL MPF PAPER LIMIT |
| Парткод: | 302LC34080 |
| Деталь: | PLATE BOTTOM |
| Парткод: | 302NG09090 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302NG09020 |
| Деталь: | CASSETTE HANDLE SIL |
| Парткод: | 302NG09120 |
| Деталь: | CT-4105 |
| Парткод: | 302NG93060 |
| Деталь: | PARTS COVER CASSETTE ASSY SP |
| Парткод: | 302NG94100 |
| Деталь: | COVER OPERATION |
| Парткод: | 302NN05010 |
| Деталь: | LENS LED OPERATION |
| Парткод: | 302NG05180 |
| Деталь: | KEY POWER SUPPLY |
| Парткод: | 302NG05060 |
| Деталь: | KEY LOGOUT INTERRUPT |
| Парткод: | 302NG05070 |
| Деталь: | KEY RESET |
| Парткод: | 302NG05050 |
| Деталь: | KEY STOP |
| Парткод: | 302NG05040 |
| Деталь: | KEY START |
| Парткод: | 302NG05030 |
| Деталь: | KEY 10 |
| Парткод: | 302NG05020 |
| Деталь: | KEY MENU |
| Парткод: | 302NG05080 |
| Деталь: | KEY CONTROL |
| Парткод: | 302NN05050 |
| Деталь: | KEY OK |
| Парткод: | 302NN05040 |
| Деталь: | KEY RETURN |
| Парткод: | 302NG05110 |
| Деталь: | KEY FUNCTION |
| Парткод: | 302NN05060 |
| Деталь: | KEY FUNCTION L |
| Парткод: | 302NN05070 |
| Деталь: | SHEET SHIELD |
| Парткод: | 302NN05100 |
| Деталь: | PARTS PWB PANEL MAIN ASSY SP |
| Парткод: | 302NN94030 |
| Деталь: | SPRING OPERATION |
| Парткод: | 302NG05310 |
| Деталь: | SHEET OPERATION |
| Парткод: | 302NN05080 |
| Деталь: | COVER PANEL |
| Парткод: | 302NN05020 |
| Деталь: | LID OPERATION |
| Парткод: | 302NG05160 |
| Деталь: | SHEET OPERATION DE |
| Парткод: | 302NN05160 |
| Деталь: | SHEET OPERATION FR |
| Парткод: | 302NN05170 |
| Деталь: | SHEET OPERATION IT |
| Парткод: | 302NN05180 |
| Деталь: | SHEET OPERATION ES |
| Парткод: | 302NN05190 |
| Деталь: | SHEET OPERATION PT |
| Парткод: | 302NN05200 |
| Деталь: | SHEET OPERATION NL |
| Парткод: | 302NN05210 |
| Деталь: | SHEET OPERATION RU |
| Парткод: | 302NN05220 |
| Деталь: | +BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | PARTS OPERATION UNIT SP |
| Парткод: | 302NN94010 |
| Деталь: | FK-4105 |
| Парткод: | 302NG93020 |
| Деталь: | FK-4107 |
| Парткод: | 302NG93030 |
| Деталь: | BUSH DU |
| Парткод: | 302F929140 |
| Деталь: | BUSH EXIT |
| Парткод: | 302HN25450 |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 302NG94180 |
| Деталь: | GUIDE EXIT PUSH |
| Парткод: | 302NG28040 |
| Деталь: | GEAR Z23S EXIT |
| Парткод: | 302NG28050 |
| Деталь: | PLATE EXIT GUIDE |
| Парткод: | 302NG28070 |
| Деталь: | BUSH EXIT SHAFT |
| Парткод: | 302NG28080 |
| Деталь: | STATIC ELIMINATOR EXIT |
| Парткод: | 302NG28090 |
| Деталь: | FRAME EXIT UPPER |
| Парткод: | 302NG28010 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR |
| Парткод: | 7BB702308H |
| Деталь: | PARTS EXIT UNIT SP |
| Парткод: | 302NG94060 |
| Деталь: | STRAP RIGHT COVER A |
| Парткод: | 302NG04550 |
| Деталь: | STRAP RIGHT COVER B |
| Парткод: | 302NG04560 |
| Деталь: | CUT WASHER 5 |
| Парткод: | 302KK04570 |
| Деталь: | STRAP RIGHT COVER C |
| Парткод: | 302NG04570 |
| Деталь: | COVER RIGHT MIDDLE |
| Парткод: | 302NG04510 |
| Деталь: | SPONGE COVER RIGHT MIDDLE |
| Парткод: | 302NG04620 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | 302NG34170 |
| Деталь: | JOINT JUNCTION HOOK |
| Парткод: | 302NG04530 |
| Деталь: | SPRING JOINT HOOK |
| Парткод: | 302NG04580 |
| Деталь: | HOOK RIGHT COVER |
| Парткод: | 302NG04520 |
| Деталь: | LABEL COVER CAUTION |
| Парткод: | 302MV34250 |
| Деталь: | LABEL COVER CAUTION 9NATIONS |
| Парткод: | 302MV34410 |
| Деталь: | STOPPER 8 |
| Парткод: | 2DC12280 |
| Деталь: | LABEL OPERATION MPF |
| Парткод: | 302NG34110 |
| Деталь: | STRAP LINK MPF F |
| Парткод: | 302NG08100 |
| Деталь: | GEAR 18 BYPASS |
| Парткод: | 2C906080 |
| Деталь: | BASE TABLE MPF |
| Парткод: | 302NG08030 |
| Деталь: | PAD LIFT |
| Парткод: | 302NG08160 |
| Деталь: | CURSOR MPF FRONT |
| Парткод: | 302NG08040 |
| Деталь: | CURSOR MPF REAR |
| Парткод: | 302NG08050 |
| Деталь: | TABLE MPF |
| Парткод: | 302NG08020 |
| Деталь: | SUB TABLE MPF A |
| Парткод: | 302NG08060 |
| Деталь: | PLATE JOINT TABLE |
| Парткод: | 302NG08090 |
| Деталь: | SUB TABLE MPF B |
| Парткод: | 302NG08070 |
| Деталь: | SUB TABLE MPF C |
| Парткод: | 302NG08080 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 2FB07330 |
| Деталь: | SPRING BYPASS TEBLE |
| Парткод: | 302FB17700 |
| Деталь: | COVER MPF |
| Парткод: | 302NG08010 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | PARTS RIGHT COVER ASSY SP |
| Парткод: | 302NG94030 |
| Деталь: | PARTS MPF TABLE ASSY SP |
| Парткод: | 302NG94040 |
| Деталь: | Резина ролика подачи бумаги |
| Парткод: | CET7829 |
| Цена: | 150 ₽ |
| Деталь: | Manual Pickup Roller |
| Парткод: | 302NG94131 |
| Цена: | 500 ₽ |
| Деталь: | PLATE POSITION A |
| Парткод: | 302H002130 |
| Деталь: | MOUNT HUMIDITY PWB |
| Парткод: | 302NG02560 |
| Деталь: | PARTS PWB HUMIDITY SENSOR ASSY SP |
| Парткод: | 302NG94280 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | STOPPER CASSETTE |
| Парткод: | 2C907100 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000004+H01 |
| Деталь: | PUSH SWITCH 03 SN /SW-192 N |
| Парткод: | 5ESP03090001+01 |
| Деталь: | PLATE SIZE DETECTION |
| Парткод: | 302NG09140 |
| Деталь: | SLIDER RAIL FRONT |
| Парткод: | 302NG14610 |
| Деталь: | PIN LOWER FRAME |
| Парткод: | 302GR25161 |
| Деталь: | GUIDE PICKUP LEVER |
| Парткод: | 302NG02330 |
| Деталь: | LEVER PICKUP |
| Парткод: | 302NG06070 |
| Деталь: | HOLDER PE LEVER |
| Парткод: | 302NG02340 |
| Деталь: | SPRING LEVER |
| Парткод: | 302NG06080 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302NG09130 |
| Деталь: | FILM PE |
| Парткод: | 302KK02370 |
| Деталь: | GUIDE LEFT FRONT |
| Парткод: | 302NG02210 |
| Деталь: | GUIDE LEFT REAR |
| Парткод: | 302NG02220 |
| Деталь: | FOOT |
| Парткод: | 302HN02611 |
| Деталь: | SHEET LSU |
| Парткод: | 302NG02590 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | MOUNT PUSH SW |
| Парткод: | 302NG02360 |
| Деталь: | LEVER RAIL REMOVEMENT |
| Парткод: | 302NG14600 |
| Деталь: | SLIDER RAIL REAR |
| Парткод: | 302NG14620 |
| Деталь: | HOLDER JOINT |
| Парткод: | 302NG14420 |
| Деталь: | GEAR JOINT Z24L |
| Парткод: | 302NG14460 |
| Деталь: | SHAFT RAIL PIVOT |
| Парткод: | 302NG14480 |
| Деталь: | RAIL DLP |
| Парткод: | 302NG14400 |
| Деталь: | PIN RAIL |
| Парткод: | 302NG14470 |
| Деталь: | SPRING JOINT GEAR |
| Парткод: | 302NG14500 |
| Деталь: | GEAR Z52R RAIL |
| Парткод: | 302NG14440 |
| Деталь: | GEAR Z25R RAIL |
| Парткод: | 302NG14450 |
| Деталь: | GEAR Z24L RAIL |
| Парткод: | 302NG14430 |
| Деталь: | COVER RAIL DLP |
| Парткод: | 302NG14410 |
| Деталь: | PLATE BIAS RAIL |
| Парткод: | 302NG14490 |
| Деталь: | SPRING BOTTOM |
| Парткод: | 302NG14650 |
| Деталь: | GUIDE WIRE LOW |
| Парткод: | 302NG02500 |
| Деталь: | MOUNT INLET |
| Парткод: | 302NG02230 |
| Деталь: | WIRE INLET |
| Парткод: | 302NG46140 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | HEATER DEHUMIDIFIER 240 |
| Парткод: | 302KK45070 |
| Деталь: | SHIELD DECK CONNECTOR |
| Парткод: | 302NG02440 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR |
| Парткод: | 7BB702308H |
| Деталь: | +BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | MOUNT LSU CONNECTOR |
| Парткод: | 302NG02510 |
| Деталь: | SHEET CONNECTOR |
| Парткод: | 302NG02580 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | WIRE POLYGON MOTOR |
| Парткод: | 302NG46110 |
| Деталь: | WIRE APC |
| Парткод: | 302NG46220 |
| Деталь: | WIRE HVU CONNECT |
| Парткод: | 302NG46020 |
| Деталь: | WIRE HVU |
| Парткод: | 302NG46030 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | LID PARTITION |
| Парткод: | 302NG02530 |
| Деталь: | RAIL CONTAINER |
| Парткод: | 302NG02310 |
| Деталь: | SEAL HOPPER |
| Парткод: | 302NG15040 |
| Деталь: | BUSH GEAR |
| Парткод: | 302F914130 |
| Деталь: | COVER CONT DRIVE |
| Парткод: | 302NG15050 |
| Деталь: | PARTS DC MOTOR ASSY SP |
| Парткод: | 302NG94050 |
| Деталь: | JOINT CONTAINER PADDLE Z49S |
| Парткод: | 302NG15070 |
| Деталь: | GEAR Z48L Z19S |
| Парткод: | 302NG15060 |
| Деталь: | SPRING JOINT SCREW |
| Парткод: | 302NG15100 |
| Деталь: | JOINT CONTAINER SCREW Z19S |
| Парткод: | 302NG15090 |
| Деталь: | GEAR Z25S Z36S |
| Парткод: | 302NG15080 |
| Деталь: | SPRING JOINT PADDLE |
| Парткод: | 302NG15120 |
| Деталь: | JOINT CONTAINER PADDLE |
| Парткод: | 302NG15110 |
| Деталь: | WIRE CONTAINER DRIVE |
| Парткод: | 302NG46120 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC04B1106+H01 |
| Деталь: | GUIDE ISU WIRE |
| Парткод: | 302NG02520 |
| Деталь: | BASE HOPPER |
| Парткод: | 302NG15010 |
| Деталь: | SHUTTER HOPPER LOW |
| Парткод: | 302NG15020 |
| Деталь: | SPRING SHUTTER HOPPER |
| Парткод: | 302NG15030 |
| Деталь: | WIRE FUSER |
| Парткод: | 302NG46060 |
| Деталь: | MOUNT RIGHT INTERLOCK |
| Парткод: | 302NG04250 |
| Деталь: | SW.MICRO |
| Парткод: | 7SM010202+++H01 |
| Деталь: | WIRE INTERLOCK |
| Парткод: | 302NG46190 |
| Деталь: | PIN FUSER COVER |
| Парткод: | 2FB20860 |
| Деталь: | SPRING BYPASSFFED |
| Парткод: | 302H008140 |
| Деталь: | RETAINER HOOK REAR |
| Парткод: | 302NG02350 |
| Деталь: | GUIDE FUSER WIRE |
| Парткод: | 302NG02480 |
| Деталь: | WIRE FUSER HEATER |
| Парткод: | 302NG46180 |
| Деталь: | BRACKET FAN |
| Парткод: | 302NG33010 |
| Деталь: | PARTS FAN MOTOR SP |
| Парткод: | 302NG94220 |
| Деталь: | MOUNT DP CONNECTOR |
| Парткод: | 302NG02490 |
| Деталь: | PARTS AC CORD EU SP |
| Парткод: | 302AR94050 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | AC CORD ASSY AS |
| Парткод: | 7AAACCAS+10H001 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR |
| Парткод: | 7BB702308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | LK-4105 |
| Парткод: | 302NG93040 |
| Деталь: | SPRING EARTH ISU |
| Парткод: | 302NG02570 |
| Деталь: | PLATE EARTH ISU |
| Парткод: | 302K302A50 |
| Деталь: | PLATE SHIELD ISU R |
| Парткод: | 302KK39650 |
| Деталь: | SPRING EARTH OPERATION |
| Парткод: | 302NG02600 |
| Деталь: | SHEET EMBLEM 22ppm |
| Парткод: | 302NN34010 |
| Деталь: | SHEET EMBLEM 18ppm |
| Парткод: | 302NC34010 |
| Деталь: | SHEET EMBLEM 22ppm(F) |
| Парткод: | 302NG34100 |
| Деталь: | SHEET EMBLEM 18ppm(F) |
| Парткод: | 302NF34010 |
| Деталь: | COVER DP CONNECTOR |
| Парткод: | 302NG17230 |
| Деталь: | PARTS CONTACT GLASS ASSY E SP |
| Парткод: | 302NG94350 |
| Деталь: | PARTS CIS ASSY SP |
| Парткод: | 302NG93070 |
| Деталь: | PARTS MOTOR ISU SP |
| Парткод: | 302NG94210 |
| Деталь: | PIN FUSER COVER |
| Парткод: | 2FB20860 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | SENSOR ORIGINAL |
| Парткод: | 302NG44040 |
| Деталь: | +TP-FLAT T.T P SCREW 3X8(BLACK) |
| Парткод: | 7BB282308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | +TP-FLAT T.T P SCREW 3X8 |
| Парткод: | 7BB202308H |
| Деталь: | GEAR Z28S |
| Парткод: | 302K331170 |
| Деталь: | GEAR INPUT DLP Z40R |
| Парткод: | 302NG31060 |
| Деталь: | SPRING FEED |
| Парткод: | 302NG31230 |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | 302NG31210 |
| Деталь: | CAM MPF |
| Парткод: | 302NG31190 |
| Деталь: | PARTS MOTOR-BL W20 SP |
| Парткод: | 302NG94190 |
| Деталь: | SOLENOID MPF |
| Парткод: | 302HN44160 |
| Деталь: | HOLDER GEAR |
| Парткод: | 302NG31220 |
| Деталь: | BUSH DRIVE 8 |
| Парткод: | 302K331230 |
| Деталь: | SHAFT CL FEED |
| Парткод: | 302NG31200 |
| Деталь: | SPRING FUSER |
| Парткод: | 302NG31240 |
| Деталь: | GEAR Z45S INPUT MPF A |
| Парткод: | 302NG31160 |
| Деталь: | SPRING INPUT MPF |
| Парткод: | 302HN31650 |
| Цена: | 150 ₽ |
| Деталь: | GEAR Z45S INPUT MPF B |
| Парткод: | 302NG31170 |
| Деталь: | GEAR Z40L |
| Парткод: | 302NG31130 |
| Деталь: | GEAR Z40L Z26L |
| Парткод: | 302NG31180 |
| Деталь: | GEAR Z37L Z28L |
| Парткод: | 302NG31140 |
| Деталь: | GEAR Z48R Z20S |
| Парткод: | 302NG31150 |
| Деталь: | GEAR Z91L Z27L |
| Парткод: | 302NG31050 |
| Деталь: | GEAR Z39L |
| Парткод: | 302NG31090 |
| Деталь: | GEAR Z92R |
| Парткод: | 302NG31110 |
| Деталь: | GEAR Z100L Z30L |
| Парткод: | 302NG31120 |
| Деталь: | GEAR INPUT FUSER Z26S |
| Парткод: | 302NG31100 |
| Деталь: | GEAR Z91L Z54L |
| Парткод: | 302NG31030 |
| Деталь: | GEAR Z46R IDLE |
| Парткод: | 302NG31070 |
| Деталь: | GEAR Z40L Z40R |
| Парткод: | 302NG31080 |
| Деталь: | GEAR INPUT DRUM Z141R |
| Парткод: | 302NG31040 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 302NG94200 |
| Деталь: | HOLDER DRIVE |
| Парткод: | 302NG31010 |
| Деталь: | TERMINAL SEPARATION |
| Парткод: | 302NG39090 |
| Деталь: | TERMINAL TRANSFER |
| Парткод: | 302NG39070 |
| Деталь: | TERMINAL DLP |
| Парткод: | 302NG39060 |
| Деталь: | TERMINAL DRUM |
| Парткод: | 302NG39080 |
| Деталь: | HOLDER CL |
| Парткод: | 302NG31020 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510017++H01 |
| Деталь: | MOUNT EXIT MOTOR |
| Парткод: | 302NG28060 |
| Деталь: | GEAR Z74R-Z21S EXIT |
| Парткод: | 302NG28030 |
| Деталь: | MOTOR EJECT |
| Парткод: | 302F944131 |
| Цена: | 4 400 ₽ |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | +BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR |
| Парткод: | 7BB702308H |
Коды ошибок
0030
0060
0100
0120
0150
0160
0170
0180
0190
0630
0800
0840
1810
1820
1830
1900
1910
1920
2000
2010
3100
3200
3210
3300
3500
3600
4000
4010
4200
6000
6020
6030
6200
6220
6230
6400
7100
7800
7810
7900
9000
9060
F000
F020
F040
F050
Описание
| Error code: | 0030 |
| Description: | FAX control PWB system error Processing with the fax software was disabled due to a software problem. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Reinstall the fax software. 3. Replace the FAX control PWB. |
| Error code: | 0060 |
| Display: | FUSER MOTOR |
| Description: | Engine PWB mismatch Unmatching engine and engine sub boards. Defective engine subboard |
| Causes: | Defective engine sub PWB. |
| Remedy: | Engine PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Replace the engine PWB. |
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0180 |
| Description: | Even though the machine carries out the regular movement, the output of Maintenance Liquid Pump Sensor does not reach the expected value. |
| Causes: | Maintenance Liquid Pump Motor has a problem. Maintenance Liquid Pump Sensor has a problem. Maintenance Liquid Pump Magnet has dropped out. Wiring or Flexible Cable has short circuitted |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Maintenance Liquid Pump Motor replacement Maintenance Liquid Pump Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0190 |
| Description: | Thermistor under the BED has a problem. |
| Causes: | Device has a problem. Thermistor Cable has short circuited or cutline. |
| Remedy: | Thermistor replacement Check Cable connection Heater Board replacement |
| Error code: | 0630 |
| Description: | DMA error DMA transmission of image data does not complete within the specified period of time. |
| Causes: | Poor contact in the connector terminals. Defective main PWB. |
| Remedy: | DP CIS 1. Reconnect the CIS signal line. 2. Confirm that the CIS connector terminals are firmly connected. Insert the connector all the way in. 3. If the wiring is disconnected, shorted or grounded, replace the wiring. DP main PWB Main PWB 1. Confirm that the wiring connector is firmly connectHDD number difference 1. Confirm whether the HDD number is correct in U024_Composition and change it if different. HDD 1piece: Single HDD 2pieces: Multied and, if necessary, connect the connector all the way in. 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Wiring that connects the CIS and the DP controller PWB. Wiring that connects the DP main PWB and the main PWB. 3. Replace the DP main PWB. 4. Replace the main PWB. |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0840 |
| Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
| Causes: | The battery is disconnected from the main PWB Defective main PWB. |
| Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
| Error code: | 1810 |
| Description: | Side multi tray communication error A communication error from side multi tray is detected 10 times in succession. |
| Causes: | Improper installation side multi tray. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. |
| Remedy: | Side multi tray Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). Engine PWB Check the engine software and upgrade to the latest, if necessary. Replace the engine PWB. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1820 |
| Description: | Side paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation side paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. Defective PF main PWB. |
| Remedy: | Side paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and SM main PWB (YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1830 |
| Description: | Paper feeder communication error (third cassette) A communication error from paper feeder is detected 10 times in succession. |
| Remedy: | Paper feeder 3 Check the wiring connection status with PF2, and if necessary, reconnect it. PF3 main PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. PF2 main PWB (YC3 and PF3 main PWB (YC5,4) 2. If the wiring is disconnected, short-circuited or has ground fault, replace the wire. 3. Reinstall the PF firmware. 4. Replace the PF3 main PWB. PF2 main PWB Replace the PF2 main PWB. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1910 |
| Description: | Side multi tray EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective SM main PWB. Device damage of EEPROM. |
| Remedy: | SM main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1920 |
| Description: | Side paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 2010 |
| Display: | Paper loaded askew. Press Load/Eject and reload the paper. |
| Description: | Main motor startup error Main motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Main motor. Engine PWB |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC13) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 3100 |
| Description: | Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor. |
| Causes: | Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective ISC PWB. Defective main PWB. |
| Remedy: | The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary. Scanner motor 1. To check the scanner motor, execute U073. 2. Move the scanner by the hand to check whether it is unusually difficult to move. 3. Check that the optical wire rope is not disengaged and engage the wire. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the scanner motor. Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and ISC PWB (YC8) 3. Replace the home position sensor. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3200 |
| Description: | Exposure lamp error When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LED lamp PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and main PWB (YC11) Defective LED lamp PWB. Replace the LED lamp PWB and check for correct operation. Defective ISC PWB. Replace the ISC PWB and check for correct operation. Defective CCD PWB. Replace the ISU and check for correct operation. Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | 3210 |
| Description: | CIS lamp error When input value at the time of CIS illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Execute CCD of U061 lamp check. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. DP relay PWB Replace the DP relay PWB. |
| Error code: | 3300 |
| Description: | Optical system (AGC) error One of the gains is FF or 00 during the CCD lamp AGC is being processed. |
| Causes: | Defective connector cable or poor contact in the connector. Defective exposure lamp Defective CCD PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | LED lamp PWB 1. To check the lamp, execute U061 CCD. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. CCD PWB Replace the ISU and execute U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3500 |
| Description: | Communication error between scanner and ASIC An error code is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective ISC PWB. Defective main PWB. |
| Remedy: | ISC PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ISC PWB (YC3) and Main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3600 |
| Description: | Scanner sequence error |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Execute U021 memory initializing. 2. Replace the ISC PWB and execute U411. |
| Error code: | 4000 |
| Display: | Supplies Drum End Soon. |
| Description: | Command Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 4010 |
| Description: | Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and engine PWB (YC11) Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 4200 |
| Display: | Supplies Replace Drum |
| Description: | BD steady-state error The BD signal is not detected. |
| Causes: | APC PWB (LSU). Main/Engine PWB. |
| Remedy: | APC PWB (LSU) 1. Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in. Laser scanner unit and main/engine PWB (YC2010) 2. If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring. 3. Replace the laser scanner unit. Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6200 |
| Display: | No Drum Unit Install the Drum Unit. |
| Description: | Broken fuser edge heater wire Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser center thermistor 1 1. Replace the Fuser unit. |
| Error code: | 6220 |
| Description: | Abnormally high fuser edge thermistor temperature Fuser thermistor 2 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 2. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6230 |
| Description: | Broken fuser edge thermistor wire The Input signal from the fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser thermistor 1 is higher than 100°C/212°F. Fuser thermistor 2 detects a lower then 50°C/122°F for 15s during warming up. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 2 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 7100 |
| Display: | Jam Rear Open the Back Cover and remove the jammed paper, then press [Start]. |
| Description: | Toner sensor error Sensor output value of 8 or less. |
| Causes: | Toner sensor. Toner motor. Main/Engine PWB. |
| Remedy: | Toner sensor 1. Check the toner sensor output by U150. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and main/engine PWB (YC9) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and main/engine PWB (YC12) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 7900 |
| Display: | Jam Manual Feed Pull out the jammed paper from Manual Feed and press Start |
| Description: | Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum unit. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and engine PWB (YC15) Defective drum unit. Replace the drum unit. |
| Error code: | 9000 |
| Description: | Document processor communication error Communication with the document processor is not possible. |
| Causes: | Defective connector cable or poor contact in the connector Defective PWB. |
| Remedy: | DP main PWB 1. Check that the versions of the main unit firmware and the DP firmware are identical. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP main PWB(YC1) and ISC PWB(YC12) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP main PWB ISC PWB Replace the ISC PWB. |
| Error code: | 9060 |
| Description: | DP EEPROM error Mismatch of reading data from two locations occurs 3 times successively. Mismatch between writing data and reading data occurs 3 times successively. |
| Causes: | Defective DP main PWB. Device damage of EEPROM. |
| Remedy: | DP main PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the EEPROM has been properly installed. 3. Replace the DP main PWB Device damage of EEPROM Contact the Service Support. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
