Kyocera TASKalfa 2420w
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
светодиодная
Макс. формат
A0
Цветность печати
черно-белая
Общие характеристики |
|
---|---|
Размещение |
напольный |
Технология печати |
светодиодная |
Телефон |
|
Факс |
|
Копир |
|
Сканер |
|
Печать фотографий |
|
Цветность печати |
|
Тип |
лазерный/светодиодный |
Макс. формат |
A0 |
Тип устройства |
МФУ |
Принтер |
|
Время разогрева |
150 |
Печать без полей |
|
Двусторонняя печать |
|
Пигментные чернила |
|
Макс, разрешение для ч/б печати |
|
По Y | 600 |
По X | 600 |
Макс, разрешение для цветной печати |
|
По Y | 2 400 |
Время выхода первого отпечатка |
|
Ч/б | 41 |
Копир |
|
Макс, количество копий за цикл |
999 |
Шаг масштабирования |
0,01 |
Время выхода первой копии |
48 |
Значение масштаба |
|
Максимальное | 4 |
Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
По Y | 600 |
По X | 600 |
Сканер |
|
Слайд-адаптер |
|
Стандарт TWAIN |
|
Отправка изображения по e-mail |
|
Макс. формат оригинала |
A0 |
Тип сканера |
протяжный |
Оттенки серого |
256 |
Макс, размер сканирования |
|
По X | 914 |
Разрешение сканера |
|
По Х | 600 |
Скорость сканирования |
|
Ч/б | 60 |
Цветн, | 60 |
Расходные материалы |
|
Количество картриджей |
1 |
Печать на: |
|
Рулоне | |
Карточках | |
Пленках | |
Этикетках | |
Глянцевой бумаге | |
Конвертах | |
Матовой бумаге | |
CD/DVD | |
Фотобумаге | |
Плотность бумаги |
|
Максимальная | 80 |
Минимальная | 64 |
Факс |
|
Цветной |
|
Телефон |
|
Спикерфон |
|
Стандарт DECT |
|
Автоответчик |
|
Caller ID |
|
АОН |
|
Беспроводная трубка |
|
Проводная трубка |
|
Языки управления |
|
PCL 5c | |
PPDS | |
PCL 6 | |
PCL 5e | |
PostScript 2 | |
PostScript 3 | |
PostScript | опционально |
Финишер |
|
Брошюровщик |
|
Электронная сортировка |
|
Сортер |
|
Степлер |
|
Интерфейсы |
|
Версия USB |
2,0 |
FireWire (IEEE 1394) |
|
Устройство для чтения карт памяти |
|
Ethernet (RJ-45) |
|
USB |
|
RS-232 |
|
LPT |
|
Инфракрасный порт |
|
Bluetooth |
|
Wi-Fi |
|
Память/Процессор |
|
Частота процессора |
2 000 |
Процессор |
Celeron |
Дополнительная информация |
|
Диагональ дисплея |
10,4 |
Экран |
|
Работа от аккумулятора |
|
Поддержка ОС |
|
Mac OS | |
DOS | |
Windows | |
Linux | |
Потребляемая мощность |
|
При работе | 760 |
В режиме ожидания | 300 |
Уровень шума |
|
В режиме ожидания | 51 |
При работе | 60 |
Габариты |
|
Глубина |
833 |
Высота |
1 147 |
Вес |
177 |
Ширина |
1 245 |
Модули
PCB LOCATION 2 (SCANNER PART)
HARNESS LIST 3(SCANNER PART 2)
PCB LOCATION 1
HOPPER ASSY
MAIN FRAME PARTS ASSY 1
HARNESS LIST 1
SCANNER ASSY 1
KIT LIST 1
ASSEMBLY LOCATION 1
SCANNER ASSY 3
HARNESS LIST 2(SCANNER PART 1)
UPPER FUSER ASSY
SCANNER ASSY 2
SET HOLDER
MAIN FRAME PARTS ASSY 2
MAIN FRAME PARTS ASSY 4
PROCCESS FRAME ASSY
LOWER FUSER ASSY
PANEL ASSY
KIT LIST 2
ASSEMBLY LOCATION 2
MAIN FRAME PARTS ASSY 3
PAPER EXIT ASSY
ACCESSORY
Детали HARNESS LIST 2(SCANNER PART 1)
Деталь: | PWB:MAIN BOARD(117) |
Парткод: | 305J071110 |
Деталь: | CIS BOARD (117) |
Парткод: | 305JZ70930 |
Деталь: | HARNESS 6 |
Парткод: | 305JG74100 |
Деталь: | HARNESS 7 |
Парткод: | 305JG74110 |
Деталь: | HARNESS 8 |
Парткод: | 305JG74120 |
Деталь: | HARNESS 9 |
Парткод: | 305JG74130 |
Деталь: | HARNESS 10 |
Парткод: | 305JG74140 |
Деталь: | HARNESS 6 |
Парткод: | 305JZ71160 |
Деталь: | HARNESS 7 |
Парткод: | 305JZ71170 |
Деталь: | HARNESS 8 |
Парткод: | 305JZ71150 |
Деталь: | HARNESS 29 |
Парткод: | 305JZ71140 |
Деталь: | HARNESS 2 |
Парткод: | 305J071130 |
Деталь: | HV POWER SUPPLY |
Парткод: | 305JG73950 |
Деталь: | PWB:PW11720 PCB ASSY |
Парткод: | 305J070040 |
Деталь: | DC POWER SUPPLY |
Парткод: | 305JZ70900 |
Деталь: | DC POWER SUPPLY |
Парткод: | 305J070100 |
Деталь: | PWB:PW11724 PCB ASSY |
Парткод: | 305JZ70910 |
Деталь: | HV-ZD ASSY |
Парткод: | 305H675990 |
Деталь: | MOTOR LIFT |
Парткод: | 305J070180 |
Деталь: | DC BLOWER(D12F-24BL 05) |
Парткод: | 305H681430 |
Деталь: | SWITCH |
Парткод: | 305J070150 |
Деталь: | HEAD CABLE 4 |
Парткод: | 305J070970 |
Деталь: | USB TERMINAL CABLE AA |
Парткод: | 305J070960 |
Деталь: | LAN TERMINAL CABLE |
Парткод: | 305J070950 |
Деталь: | IF CABLE |
Парткод: | 305J070920 |
Деталь: | USB CABLE AB |
Парткод: | 305J070910 |
Деталь: | UI DC SUPPLY HARNESS |
Парткод: | 305J070200 |
Деталь: | SSR LEAD |
Парткод: | 305H676100 |
Деталь: | HARNESS:FLICKER LEAD(230V) |
Парткод: | 305J070930 |
Деталь: | USB TERMINAL CABLE 2 AA |
Парткод: | 305J070990 |
Деталь: | AC MAIN HARNESS 3(230V) |
Парткод: | 305J070760 |
Деталь: | DEVELOPER HARNESS |
Парткод: | 305J070850 |
Деталь: | DRIVING SIDE HARNESS |
Парткод: | 305J070870 |
Деталь: | AC MAIN HARNESS(120V) |
Парткод: | 305J070740 |
Деталь: | AC MAIN HARNESS 2(230V) |
Парткод: | 305J070750 |
Деталь: | HARNESS:MOTOR LEAD |
Парткод: | 305J070820 |
Деталь: | DC MAIN HARNESS |
Парткод: | 305J070730 |
Деталь: | ANTI-DRIVING SIDE HARNESS |
Парткод: | 305J070860 |
Деталь: | PROCESS UNIT HARNESS |
Парткод: | 305J070940 |
Деталь: | HARNESS:BIAS LEAD 2 |
Парткод: | 305J070830 |
Деталь: | POWER CABLE |
Парткод: | 305JG71120 |
Деталь: | POWER CABLE (EU) |
Парткод: | 305JZ71000 |
Деталь: | HARNESS:1ST LEAD |
Парткод: | 305J070840 |
Деталь: | HARNESS:HEATER BOWER LEAD |
Парткод: | 305J070770 |
Деталь: | HARNESS:EXIT SENSOR TRANSIT LEAD |
Парткод: | 305J070980 |
Деталь: | EXIT SENSOR HARNESS |
Парткод: | 305J070880 |
Деталь: | HARNESS:PAPER SENSOR LEAD |
Парткод: | 305J070890 |
Деталь: | HARNESS:PAPER SENSOR LEAD 2 |
Парткод: | 305J070900 |
Деталь: | HARNESS:STRIP SENSOR LEAD |
Парткод: | 305J070810 |
Деталь: | HARNESS:RESIST SENSOR LEAD |
Парткод: | 305J070790 |
Деталь: | HARNESS:HAND SENSOR LEAD |
Парткод: | 305J070800 |
Деталь: | CIS SENSOR C |
Парткод: | 305JZ70180 |
Деталь: | SPRING 2(10PCS) |
Парткод: | 305JG77040 |
Деталь: | X3 DOC ROLL ASSY |
Парткод: | 305JG74600 |
Деталь: | SHEET GUIDE 117 |
Парткод: | 305J071240 |
Деталь: | P4 GUARD DOC L |
Парткод: | 305JG74630 |
Деталь: | GUIDE:P GUARD DOC MC |
Парткод: | 305J071280 |
Деталь: | GUIDE:P GUARD DOC C |
Парткод: | 305J071270 |
Деталь: | P4 GUARD DOC 55 |
Парткод: | 305JG74650 |
Деталь: | P4 GUARD DOC S |
Парткод: | 305JG74610 |
Деталь: | P4 GUARD DOC M |
Парткод: | 305JG74620 |
Деталь: | SHADING SEAT |
Парткод: | 305JZ70210 |
Деталь: | STITCH ADJUSTMENT CHART |
Парткод: | 305JG74560 |
Деталь: | SLEEVE |
Парткод: | 305JZ70220 |
Деталь: | SPRING 2 |
Парткод: | 305J071260 |
Деталь: | SERVICE KIT A(OPTION) |
Парткод: | 1705J00UN0 |
Деталь: | SERVICE KIT B(OPTION) |
Парткод: | 1705J00UN1 |
Деталь: | SERVICE KIT C(OPTION) |
Парткод: | 1705J00UN2 |
Деталь: | HOPPER ASSY |
Парткод: | 305J070710 |
Деталь: | CUTTER |
Парткод: | 305J070010 |
Деталь: | CAP SET |
Парткод: | 305JG70130 |
Деталь: | TOUCH PANEL LCD UNIT |
Парткод: | 305J071000 |
Деталь: | CONTROLLER ASSY:IPS DC1 CONTROLLER |
Парткод: | 305JZ70040 |
Деталь: | HDD:SATA HDD 2.5 250G (BLANK) |
Парткод: | 305JZ70070 |
Деталь: | MEMORY DDR2 DIMM 800 1G |
Парткод: | 305JZ70080 |
Деталь: | DC-DC POWER SUPPLY |
Парткод: | 305JZ70090 |
Деталь: | PWB:MOTHER BOARD |
Парткод: | 305JZ70100 |
Деталь: | SWITCH |
Парткод: | 305H678900 |
Деталь: | SENSOR |
Парткод: | 305H676760 |
Деталь: | FIX ROLLER ASSY |
Парткод: | 305JZ70240 |
Деталь: | HARNESS 4 |
Парткод: | 305JZ71110 |
Деталь: | HARNESS 3 |
Парткод: | 305JZ71120 |
Деталь: | HARNESS 5 |
Парткод: | 305JZ71130 |
Деталь: | USB CABLE 2.9 |
Парткод: | 305JG74250 |
Деталь: | HARNESS |
Парткод: | 305J071120 |
Деталь: | HARNESS 15 |
Парткод: | 305JG74180 |
Деталь: | HARNESS 13 |
Парткод: | 305JG74160 |
Деталь: | HARNESS 14 |
Парткод: | 305JG74170 |
Деталь: | THERMISTOR1 |
Парткод: | 305J070020 |
Деталь: | THERMISTOR2 |
Парткод: | 305J070030 |
Деталь: | THERMOSTAT |
Парткод: | 305JG71100 |
Деталь: | ROLLER FUSING 5 |
Парткод: | 305J070090 |
Деталь: | LAMP 120V |
Парткод: | 305J070060 |
Деталь: | LAMP 230V |
Парткод: | 305J070050 |
Деталь: | SCAN GLASS ASSY |
Парткод: | 305JG74360 |
Деталь: | PINCH ROLLER ASSY |
Парткод: | 305JG74370 |
Деталь: | SPRING 3 |
Парткод: | 305JZ70230 |
Деталь: | FEED ROLLER R |
Парткод: | 305JG74300 |
Деталь: | FEED ROLLER F |
Парткод: | 305JG74290 |
Деталь: | PRESS ASSY 2 |
Парткод: | 305JG70650 |
Деталь: | PRESS ASSY 1 |
Парткод: | 305JG70640 |
Деталь: | PRESS ASSY 3 |
Парткод: | 305JG70660 |
Деталь: | STAY ASSY |
Парткод: | 305JG74380 |
Деталь: | BEARING |
Парткод: | 305H676710 |
Деталь: | POLYSLIDER WASHER |
Парткод: | 305H677180 |
Деталь: | POM WASHER |
Парткод: | 305H677120 |
Деталь: | DAMPER R |
Парткод: | 305J071160 |
Деталь: | GEAR (LATCH) |
Парткод: | 305J071170 |
Деталь: | GEAR (DAMP) |
Парткод: | 305J071180 |
Деталь: | PULLEY 36Z R |
Парткод: | 305J071220 |
Деталь: | PULLEY 36Z F |
Парткод: | 305J071210 |
Деталь: | MOTOR PULLEY 24Z |
Парткод: | 305J071230 |
Деталь: | MOTOR ASSY |
Парткод: | 305J071140 |
Деталь: | DAMPER L |
Парткод: | 305J071150 |
Деталь: | BELT 40S2M220 |
Парткод: | 305J071190 |
Деталь: | BELT 40S2M266 |
Парткод: | 305J071200 |
Деталь: | STUD |
Парткод: | 305H677210 |
Деталь: | Bush |
Парткод: | 305H677220 |
Деталь: | SPRING |
Парткод: | 305J071250 |
Деталь: | SET HOLDER SET |
Парткод: | 305J071060 |
Деталь: | 40T GEAR 32T PULLEY |
Парткод: | 305J070450 |
Деталь: | 48T GEAR 40T PULLEY |
Парткод: | 305J070560 |
Деталь: | 60T GEAR 40T PULLEY |
Парткод: | 305J070550 |
Деталь: | BELT: 115S3M963G |
Парткод: | 305J070600 |
Деталь: | BELT:100S2M520G |
Парткод: | 305J070500 |
Деталь: | BEARING (608ZZ/L353) |
Парткод: | 305JG71140 |
Деталь: | 18T-30T GEAR |
Парткод: | 305J070540 |
Деталь: | 30T-75T PULLEY |
Парткод: | 305J070490 |
Деталь: | GEAR 28T |
Парткод: | 305H674850 |
Деталь: | 23T GEAR |
Парткод: | 305J070570 |
Деталь: | STEPPING CLUTCH |
Парткод: | 305J070170 |
Деталь: | MICRO CLUTCH |
Парткод: | 305J070160 |
Деталь: | SWITCH |
Парткод: | 305JZ70150 |
Деталь: | DC motor |
Парткод: | 305JG73960 |
Деталь: | 24 PULLEY |
Парткод: | 305J070590 |
Деталь: | NOISE FILTER ASSY |
Парткод: | 305H675950 |
Деталь: | INLET ASSY |
Парткод: | 305H675960 |
Деталь: | BREAKER |
Парткод: | 305H678970 |
Деталь: | BREAKER |
Парткод: | 305H678130 |
Деталь: | SENSOR |
Парткод: | 305H678790 |
Деталь: | SENSOR |
Парткод: | 305J070110 |
Деталь: | 30T gear |
Парткод: | 305J070580 |
Деталь: | Relay |
Парткод: | 305H678980 |
Деталь: | SOLID STATE RELAY 120V |
Парткод: | 305JG71110 |
Деталь: | SOLID STATE RELAY 230V |
Парткод: | 305JG74950 |
Деталь: | NOIZE FILTER |
Парткод: | 305H678200 |
Деталь: | SENSOR |
Парткод: | 305J070130 |
Деталь: | TONER DENSITY SENSOR |
Парткод: | 305JG71080 |
Деталь: | BELT:100S3M453G |
Парткод: | 305J070510 |
Деталь: | BELT:100S3M387G |
Парткод: | 305J070520 |
Деталь: | BELT:100S3M255G |
Парткод: | 305J070530 |
Деталь: | 30T-54T PULLEY |
Парткод: | 305J070460 |
Деталь: | 30T-60T PULLEY |
Парткод: | 305J070470 |
Деталь: | 24T HELICAL 32 PULLEY |
Парткод: | 305J070480 |
Деталь: | ROLLER PRESSURE 2 |
Парткод: | 305J070080 |
Деталь: | BEARING(6002ZZNR) |
Парткод: | 305J070190 |
Деталь: | SENSOR |
Парткод: | 305J070110 |
Деталь: | BRACKET 3 ASSY |
Парткод: | 305J070700 |
Деталь: | COVER 7 |
Парткод: | 305J070650 |
Деталь: | COVER 9 |
Парткод: | 305J070670 |
Деталь: | COVER 8 |
Парткод: | 305J070660 |
Деталь: | GUIDE 3 |
Парткод: | 305J070680 |
Деталь: | GUIDE 4 |
Парткод: | 305J070690 |
Деталь: | SCANNER COVER ASSY |
Парткод: | 305J070390 |
Деталь: | GUIDE 2 |
Парткод: | 305J070440 |
Деталь: | COVER 19 |
Парткод: | 305J070280 |
Деталь: | COVER 20 |
Парткод: | 305J070290 |
Деталь: | COVER 14 |
Парткод: | 305J070230 |
Деталь: | COVER 18 |
Парткод: | 305J070260 |
Деталь: | BUTTON |
Парткод: | 305J070270 |
Деталь: | COVER 6 |
Парткод: | 305J070210 |
Деталь: | COVER 21 |
Парткод: | 305J070300 |
Деталь: | COVER 22 |
Парткод: | 305J070310 |
Деталь: | COVER |
Парткод: | 305J070630 |
Деталь: | LEVER:MANUAL TRAY KNOB |
Парткод: | 305J071290 |
Деталь: | COVER 36 |
Парткод: | 305J070370 |
Деталь: | COVER 32 |
Парткод: | 305J070350 |
Деталь: | COVER 31 |
Парткод: | 305J070330 |
Деталь: | COVER 7 |
Парткод: | 305J070220 |
Деталь: | COVER 16 |
Парткод: | 305J070240 |
Деталь: | COVER 17 |
Парткод: | 305J070250 |
Деталь: | LEVER |
Парткод: | 305J070610 |
Деталь: | TOUCH PEN |
Парткод: | 305J070320 |
Деталь: | GUIDE COVER 2 |
Парткод: | 305J070340 |
Деталь: | PAD |
Парткод: | 305J070380 |
Деталь: | GUIDE ASSY |
Парткод: | 305JZ71200 |
Деталь: | GUIDE 2 ASSY |
Парткод: | 305JZ71210 |
Деталь: | BRUSH DISCHARGE SET |
Парткод: | 305J071030 |
Деталь: | FUSE SET |
Парткод: | 305J071040 |
Деталь: | LED HEAD ASSY |
Парткод: | 305J070070 |
Деталь: | SENSOR |
Парткод: | 305J070120 |
Деталь: | SWITCH |
Парткод: | 305J070140 |
Деталь: | SWITCH |
Парткод: | 305H678900 |
Деталь: | FAN ASSY |
Парткод: | 305JZ70140 |
Деталь: | BRACKET 221 ASSY (SENSOR) |
Парткод: | 305J071020 |
Деталь: | HV SOCKET ASSY |
Парткод: | 305J070780 |
Деталь: | DC FAN ASSY |
Парткод: | 305H679980 |
Деталь: | SPRING 4 |
Парткод: | 305J070720 |
Деталь: | NAIL STRIPPING |
Парткод: | 305H679940 |
Деталь: | COVER 4 |
Парткод: | 305J070640 |
Деталь: | GUIDE |
Парткод: | 305J070360 |
Деталь: | FLANGE SET(2 INCH) |
Парткод: | 305J071050 |
Коды ошибок
E-0000
E-0001
E-0002
E-0003
E-0004
E-0005
E-0010
E-0013
E-0020
E-0031
E-0032
E-0033
E-0034
E-0040
E-0050
E-0070
E-0080
E-0081
E-0090
Описание
Error code: | E-0000 |
Description: | Fuser Temperature Rising Error Fuser Temperature does not reach 50C within 120 seconds after turning on. |
Causes: | Fuser Temperature does not reach 50 oC within 120 seconds after turning on. |
Remedy: | Error clearance 1 Have you cleared the fuser error in the Special Operation Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Special Operation Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Lamp (H1) 3 Unplug the machine, and then check the resistance of Lamp (H1) with the multimeter. Is it 15k ohm or lower? No Replace the Lamp. Thermistors (TH1 & TH2) 4 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. Confirm that the machine is turned on, and then check the voltage of the orange line (J220-4, 220-5, 220-6). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. DC Power Supply (DCP1) or Fuse 5 Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Relay (RY1) 6 Select the Operation Check Mode, and then change the signal of the following signal to “H”. Device Code : 22 (Fuser Relay) And check the resistance between the following points. Between RY1-2 and RY1-4 Between RY1-6 and RY1-8 Is the each resistance almost 0 ohm? No Replace the Relay. Solid State Relay (SSR1) 7 Select the Operation Check Mode, and then change the signal of the following signals to “H”. Device Code : 22 (Fuser Relay) 21 (Fuser Lamp 1) Then check the voltage between J600 and J601. Is it 0V? CAUTION: Change the signal of “21” (Fuser Lamp 1) to “L” after checking! Yes Replace the Solid State Relay No Replace the PW11720 PCB. |
Error code: | E-0001 |
Description: | Fuser Over Temperature Error Fuser Temperature reaches over 200C. |
Causes: | (1) Fuser is not heated up to 50Co within 6 minutes after turning on. (2) Fuser is not heated up to 100Co within 6 minutes since it has heated up to 50Co. (3) Fuser is not heated up to the ready temperature within 6 minutes since it has heated up to 100Co. (4) Fuser is cooled down to 100Co since once it has been ready. (5) 0Co is detected for 1 minute continuously when the Fuser Lamps are ON. |
Remedy: | Error clearance 1 Have you cleared the fuser error in the Special Operation Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Special Operation Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Solid State Relay (SSR1) 3 Does the error occur again even if you have cleared it in the Special Operation Mode? Yes Replace the Solid State Relay. Thermistors (TH1 & TH2) 4 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. |
Error code: | E-0002 |
Description: | Fuser Low Temperature Error 1. Fuser Temperature at the time of turning on was 50 to 100C, but it does not rise up to 120C within 150 seconds after that. 2. Fuser Temperature at the time of turning on was higher than 100C, but it does not rise up to the setting temperature within 270 seconds after that. |
Causes: | (1) When over 200Co is detected. (2) When “fuser abnormally hot signal” shows “H” for longer than 100msec. |
Remedy: | Error clearance 1 Have you cleared the fuser error in the Special Operation Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Special Operation Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Lamp (H1) 3 Unplug the machine, and then check the resistance of Lamp (H1) with the multimeter. Is it 15k ohm or lower? No Replace the Lamp. Thermistors (TH1 & TH2) 4 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. Confirm that the machine is turned on, and then check the voltage of the orange line (J220-4, 220-5, 220-6). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. DC Power Supply (DCP1) or Fuse 5 Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Relay (RY1) 6 Select the Operation Check Mode, and then change the signal of the following signal to “H”. Device Code : 22 (Fuser Relay) And check the resistance between the following points. Between RY1-2 and RY1-4 Between RY1-6 and RY1-8 Is the each resistance almost 0 ohm? No Replace the Relay. Solid State Relay (SSR1) 7 Select the Operation Check Mode, and then change the signal of the following signals to “H”. Device Code : 22 (Fuser Relay) 21 (Fuser Lamp 1) Then check the voltage between J600 and J601. Is it 0V? CAUTION: Change the signal of “21” (Fuser Lamp 1) to “L” after checking! Yes Replace the Solid State Relay No Replace the PW11720 PCB. |
Error code: | E-0003 |
Description: | Fuser Temperature Abnormal Fall Error The difference of temperature between center and side of fuser becomes 50C or more. |
Causes: | The difference of temperature between center and side of fuser becomes 50 oC or more. |
Remedy: | Error clearance 1 Have you cleared the fuser error in the Special Operation Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Special Operation Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Thermistors (TH1 & TH2) 3 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. |
Error code: | E-0004 |
Description: | Fuser Temperature Abnormal Fall Error The Lamp of fuser lights (Signal HEAT1 is “H”) to heat up the Fuser Roller in the ready condition, but even 1C of temperature rise can not be accomplished within 30 seconds. |
Causes: | The Lamp of fuser lights (Signal HEAT1 is “H”) to heat up the Fuser Roller in the ready condition, but even 1 oC of temperature rise can not be accomplished within 30 seconds. |
Remedy: | Error clearance 1 Have you cleared the fuser error in the Special Operation Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Special Operation Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Lamp (H1) 3 Unplug the machine, and then check the resistance of Lamp (H1) with the multimeter. Is it 15k ohm or lower? No Replace the Lamp. Thermistors (TH1 & TH2) 4 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. Confirm that the machine is turned on, and then check the voltage of the orange line (J220-4, 220-5, 220-6). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. DC Power Supply (DCP1) or Fuse 5 Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Relay (RY1) 6 Select the Operation Check Mode, and then change the signal of the following signal to “H”. Device Code : 22 (Fuser Relay) And check the resistance between the following points. Between RY1-2 and RY1-4 Between RY1-6 and RY1-8 Is the each resistance almost 0 ohm? No Replace the Relay. Solid State Relay (SSR1) 7 Select the Operation Check Mode, and then change the signal of the following signals to “H”. Device Code : 22 (Fuser Relay) 21 (Fuser Lamp 1) Then check the voltage between J600 and J601. Is it 0V? CAUTION: Change the signal of “21” (Fuser Lamp 1) to “L” after checking! Yes Replace the Solid State Relay No Replace the PW11720 PCB. |
Error code: | E-0005 |
Description: | Fuse Error Fuse (F1) is broken. |
Causes: | Fuse (F1) is broken. |
Remedy: | Wires 1 Is the wire between the Fuse and PW11720 PCB connected properly? No Connect it properly. DC Power Supply (DCP1) or Fuse 2 Confirm that the machine is turned OFF, and then check the Fuse. Is it OK? No Replace the Fuse with a new one. 3 Confirm that the machine is turned on, and then check the voltage of the orange line (J220-5). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. |
Error code: | E-0010 |
Description: | Main Motor Error The Main Motor Output Detection Signal (MAINM_LD) continues to be “H” for 3 seconds or longer when the Main Motor is rotating. |
Causes: | The Main Motor Output Detection Signal (MAINM_LD) continues to be “H” for 3 seconds or longer when the Main Motor is rotating. |
Remedy: | Wires 1 Is the wire between Main Motor and PW11720 PCB connected properly? No Connect it properly. Confirm that the machine is turned on, and then check the voltage of the orange line (J220-5). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. DC Power Supply (DCP1) or Fuse 2 Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Main Motor (M1) 3 Check the operation of Main Motor in the Operation Check Mode of the Service Mode. Device Code : 00 (Main Motor) Does the Main Motor operate correctly? No Replace the Main Motor. |
Error code: | E-0013 |
Description: | Paper Tray Motor Error The Paper Tray Motor Output Detection Signal (CSETM_LD) continues to be “H” for 3 seconds or longer when the Paper Tray Motor is rotating. |
Causes: | The Paper Tray Motor Output Detection Signal (CSETM_LD) continues to be “H” for 3 seconds or longer when the Paper Tray Motor is rotating. |
Remedy: | Wires 1 Is the wire between Paper Tray Motor and PW11720 PCB connected properly? No Connect it properly. Confirm that the machine is turned on, and then check the voltage of the orange line. Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. DC Power Supply (DCP1) or Fuse 2 Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Paper Tray Motor (M3) 3 Check the operation of Main Motor in the Operation Check Mode of the Service Mode. Device Code : 33 (Paper Tray Motor) Does the Main Motor operate correctly? No Replace the Main Motor. |
Error code: | E-0020 |
Description: | Counter Error The Counter Connection Detection Signal (COUNT_OPN) continues to be “L” for 1 second or longer after turning on. |
Causes: | “Thermostat status signal” shows “L” continuously for longer than 100msec. |
Remedy: | Service Mode 1 Has the setting of Adjustment Mode Item No.753 set to “1” ? Yes Set it to “0”. |
Error code: | E-0031 |
Description: | Image Corona Output Error The Image Corona Output Detection Signal (IM_LD) continues to be “L” for 1 second or longer when the Image Corona is ON. |
Causes: | The Image Corona Output Detection Signal (IM_LD) continues to be “L” for 1 second or longer when the Image Corona is ON. |
Remedy: | Wire 1 Are wires among Image Corona, HV Power Supply PCB and PW11720 PCB connected properly? No Connect them properly. 2 (For Image Corona / Cleaning Roller only) Is the spring on the left bottom of the Process Unit OK? No Correct it properly. Is the Image Corona dirty? Yes Clean each Corona Wire, Grid Plate and housing. Image Corona 3 Is the Corona Wire broken? Yes Replace the Corona Wire. Does the bias terminal plate touch to Cleaning Roller shaft properly? No Remove and reapply conductive grease to Cleaning Roller shaft. Relocate the bias terminal plates properly. Cleaning Roller 4 Is grease applied enough? No Remove and reapply conductive grease to Cleaning Roller shaft. Is the Transfer Corona dirty? Yes Clean each Corona Wire and housing. Transfer Corona 5 Is the Corona Wire broken? Yes Replace the Corona Wire. Is the Separation Corona dirty? Yes Clean each Corona Wire and housing. Separation Corona 6 Is the Corona Wire broken? Yes Replace the Corona Wire. HV Power Supply 7 Can you fix the problem if you replace the HV Power Supply? Yes OK |
Error code: | E-0032 |
Description: | Separation Corona Output Error The Separation Corona Output Detection Signal (AC_LD) continues to be “L” for 1 second or longer when the Separation Corona is ON. |
Causes: | The Separation Corona Output Detection Signal (AC_LD) continues to be “L” for 1 second or longer when the Separation Corona is ON. |
Remedy: | Wire 1 Are wires among Image Corona, HV Power Supply PCB and PW11720 PCB connected properly? No Connect them properly. 2 (For Image Corona / Cleaning Roller only) Is the spring on the left bottom of the Process Unit OK? No Correct it properly. Is the Image Corona dirty? Yes Clean each Corona Wire, Grid Plate and housing. Image Corona 3 Is the Corona Wire broken? Yes Replace the Corona Wire. Does the bias terminal plate touch to Cleaning Roller shaft properly? No Remove and reapply conductive grease to Cleaning Roller shaft. Relocate the bias terminal plates properly. Cleaning Roller 4 Is grease applied enough? No Remove and reapply conductive grease to Cleaning Roller shaft. Is the Transfer Corona dirty? Yes Clean each Corona Wire and housing. Transfer Corona 5 Is the Corona Wire broken? Yes Replace the Corona Wire. Is the Separation Corona dirty? Yes Clean each Corona Wire and housing. Separation Corona 6 Is the Corona Wire broken? Yes Replace the Corona Wire. HV Power Supply 7 Can you fix the problem if you replace the HV Power Supply? Yes OK |
Error code: | E-0033 |
Description: | Transfer Corona Output Error The Transfer Corona Output Detection Signal (TR_LD) continues to be “L” for 1 second or longer when the Transfer Corona is ON. |
Causes: | The Transfer Corona Output Detection Signal (TR_LD) continues to be “L” for 1 second or longer when the Transfer Corona is ON. |
Remedy: | Wire 1 Are wires among Image Corona, HV Power Supply PCB and PW11720 PCB connected properly? No Connect them properly. 2 (For Image Corona / Cleaning Roller only) Is the spring on the left bottom of the Process Unit OK? No Correct it properly. Is the Image Corona dirty? Yes Clean each Corona Wire, Grid Plate and housing. Image Corona 3 Is the Corona Wire broken? Yes Replace the Corona Wire. Does the bias terminal plate touch to Cleaning Roller shaft properly? No Remove and reapply conductive grease to Cleaning Roller shaft. Relocate the bias terminal plates properly. Cleaning Roller 4 Is grease applied enough? No Remove and reapply conductive grease to Cleaning Roller shaft. Is the Transfer Corona dirty? Yes Clean each Corona Wire and housing. Transfer Corona 5 Is the Corona Wire broken? Yes Replace the Corona Wire. Is the Separation Corona dirty? Yes Clean each Corona Wire and housing. Separation Corona 6 Is the Corona Wire broken? Yes Replace the Corona Wire. HV Power Supply 7 Can you fix the problem if you replace the HV Power Supply? Yes OK |
Error code: | E-0034 |
Description: | Bias Output Error Bias Output Detection Signal (BIAS_LD) continues to be “L” for 1 second or longer when a specified bias is supplied to the corresponding Developer Unit components. |
Causes: | Bias Output Detection Signal (BIAS_LD) continues to be “L” for 1 second or longer when a specified bias is supplied to the corresponding Developer Unit components. |
Remedy: | Wires 1 Are wires among Developer Unit, HV Power Supply PCB and PW11720 PCB connected properly? No Connect them properly. Is the toner spill out from the Developer Unit? (Or is there any similar problem?) Yes Clean each Corona Wire, Grid Plate and housing. Developer Unit 2 Is the high voltage of Regulation Roller leaking? (The resistance between the central part of Regulation Roller and the Ground is 5 mega ohm or smaller if leaking.) Yes Replace the Regulation Roller. HV Power Supply 3 Can you fix the problem if you replace the HV Power Supply? Yes OK |
Error code: | E-0040 |
Description: | Cutter Error 1. The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to “H” within 100 millisecond since the Cutter has started the operation. 2. The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to “L” within 1 second since the Cutter has started the operation. |
Causes: | 1. The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to “H” within 100 millisecond since the Cutter has started the operation. 2. The Cutter Home Sensor Signal (MSCUT_L or MSCUT_R) does not change to “L” within 1 second since the Cutter has started the operation. |
Remedy: | Wires 1 Is the wire between Cutter Unit and PW11720 PCB connected properly? No Connect it properly. Cutter Home Position Sensors (MS8 & MS9) 2 Check the status of the following signals in the Signal Status Mode of the Service Mode. Signal Code : 094 (Cutter Home Position Right) 095 (Cutter Home Position Left) Is the status “L” when the Cutter is at each home position? No Replace the Cutter Unit. Cutter Motor (M4) 3 Check the operation of Cutter in the Operation Check Mode of the Service Mode. Device Code : 27 (Cutter Motor 1) 28 (Cutter Motor 2) Does the Cutter operate? No Replace the Cutter Unit. |
Error code: | E-0050 |
Description: | FPGA Error Initialization of FPGA is failed after turning on. |
Causes: | Initialization of FPGA is failed after turning on. |
Remedy: | PW11720 PCB 1 Can you fix the problem if you replace the PW11720 PCB? Yes OK |
Error code: | E-0070 |
Description: | Developer Error 1. The Connector J-253 is not connected. 2. The Switch (MS4) is “open” condition, which detects open/close of Engine Unit or Toner Hatch. |
Causes: | 1. The Connector J-253 is not connected. 2. The Switch (MS4) is “open” condition, which detects open/close of Engine Unit or Toner Hatch. |
Remedy: | Wires 1 Is the wire between Developer Unit and PW11720 PCB connected properly? No Connect it properly. |
Error code: | E-0080 |
Description: | Density Sensor Error Density Sensor cannot be calibrated correctly before Density Measure. |
Causes: | Density Sensor cannot be calibrated correctly before Density Measure. |
Remedy: | Wires 1 Is the wire between Toner Density Sensor and PW11720 PCB connected properly? No Connect it properly. Density Sensor (PH8) 2 Can you fix the problem if you replace Density Sensor? No Replace PW11720 with a new one. |
Error code: | E-0081 |
Description: | Density Sensor Error Density Sensor cannot be calibrated correctly before Density Measure. |
Remedy: | Wires 1 Is the wire between Toner Density Sensor and PW11720 PCB connected properly? No Connect it properly. Density Sensor (PH8) 2 Can you fix the problem if you replace Density Sensor? No Replace PW11720 with a new one. |
Error code: | E-0090 |
Description: | Eraser Lamp Error 1. The connector J-227 / J-228 is not connected. 2. Eraser Lamp (PW6631) is broken. |
Causes: | 1. The connector J-227 / J-228 is not connected. 2. Eraser Lamp (PW6631) is broken. |
Remedy: | Wires 1 Is the wire between Toner Density Sensor and PW11720 PCB connected properly? Is the spring on the left bottom of the Process Unit OK? No Connect it properly. Eraser Lamp 2 Can you fix the problem if you replace the Process Unit? No Replace PW11720 with a new one. |
Парткод
Название
Kyocera Тонер-картридж черный 2шт.