Kyocera TASKalfa 255
Рейтинг
Модули
Document Processor 1
FRAMES 1
Laser Scanner Section
DEVELOPING SECTION
COVERS
ORIGINAL COVER
PAPER CASSETTE
Fuser Section
Paper Conveying Section
Paper Feed Section 1
Operation Section
PAPER FEED SECTION 2
Document Processor 3
Image Formation Section
FRAMES 2
Document Processor 2
DRIVE SECTION
SCANNER SECTION
Детали Document Processor 2
| Деталь: | COVER TABLE WIRE |
| Парткод: | 303LL06100 |
| Деталь: | LEFT HINGE |
| Парткод: | 303M802020 |
| Деталь: | COVER FRONT |
| Парткод: | 303M804010 |
| Деталь: | COVER REAR |
| Парткод: | 303M804020 |
| Деталь: | COVER LEFT |
| Парткод: | 303M804040 |
| Деталь: | LID REAR COVER |
| Парткод: | 303M804060 |
| Деталь: | COVER LED |
| Парткод: | 303M804070 |
| Деталь: | LID INNER COVER |
| Парткод: | 303M804080 |
| Деталь: | TRAY LOOP |
| Парткод: | 303M806050 |
| Деталь: | GEAR 20,CASSETTE |
| Парткод: | 65907210 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | GEAR,WORM MAIN TRAY |
| Парткод: | 3AK20130 |
| Деталь: | PUSH SW DP |
| Парткод: | 3HL02240 |
| Деталь: | PLATE ORIGINAL |
| Парткод: | 303JC04200 |
| Деталь: | CUSHION ORIGINAL MAT A |
| Парткод: | 303MX02021 |
| Деталь: | COVER HINGE |
| Парткод: | 303M804090 |
| Деталь: | STOPPER EJECT |
| Парткод: | 303M804050 |
| Деталь: | LABEL PAPER SET CAUTION ENG |
| Парткод: | 303M834110 |
| Деталь: | LABEL MSP A |
| Парткод: | 303H605110 |
| Деталь: | LABEL HINGE CAUTION |
| Парткод: | 303M834070 |
| Деталь: | LABEL FACE UP 7NATIONS |
| Парткод: | 303LL34190 |
| Деталь: | PARTS TABLE ASSY SP |
| Парткод: | 303M894060 |
| Деталь: | PARTS GEAR CONTAINER Z18L SP |
| Парткод: | 302K394260 |
| Деталь: | PARTS GEAR CONTAINER Z25L SP |
| Парткод: | 302K394270 |
| Деталь: | PARTS GEAR CONTAINER Z35R SP |
| Парткод: | 302K394280 |
| Деталь: | PARTS GEAR CONTAINER Z24L-Z19R SP |
| Парткод: | 302K394290 |
| Деталь: | PARTS GEAR CONTAINER Z41L SP |
| Парткод: | 302K394300 |
| Деталь: | PARTS GEAR CONTAINER Z20R SP |
| Парткод: | 302K394390 |
| Деталь: | ACTUATOR DECK FEED |
| Парткод: | 302K302830 |
| Деталь: | PARTS MOTOR LIFT ASSY SP |
| Парткод: | 302K394190 |
| Цена: | 6 000 ₽ |
| Деталь: | PARTS LVU MAIN 120 SP |
| Парткод: | 302K394110 |
| Деталь: | PARTS LVU MAIN 200 SP |
| Парткод: | 302K394120 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302K302810 |
| Деталь: | PARTS CONT SENSOR ASSY SP |
| Парткод: | 302KK94070 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | COVER INNER LOW |
| Парткод: | 302K304080 |
| Деталь: | SW.MICRO |
| Парткод: | 7SM010202+++H01 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302K394070 |
| Деталь: | PARTS PWB DEVE CONNECT ASSY SP |
| Парткод: | 302K394090 |
| Деталь: | PARTS PWB DRUM CONNECT ASSY SP |
| Парткод: | 302K394080 |
| Деталь: | PARTS PWB HUMIDITY SENSOR ASSY SP |
| Парткод: | 302K394100 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | AC CORD ASSY AS |
| Парткод: | 7AAACCAS+10H001 |
| Деталь: | +BIND T.T S SCREW 3X12 SR |
| Парткод: | 7BB700312H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | LK-475 |
| Парткод: | 302K393070 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR |
| Парткод: | 7BB702308H |
| Деталь: | DV-475 |
| Парткод: | 302K393040 |
| Деталь: | PARTS COVER FRONT ASSY 30 J/E SP (30ppm) |
| Парткод: | 302K394430 |
| Деталь: | PARTS COVER FRONT ASSY 25 J/E SP (25ppm) |
| Парткод: | 302L394020 |
| Деталь: | PARTS COVER FRONT ASSY 30 A SP (30ppm) |
| Парткод: | 302K394440 |
| Деталь: | PARTS COVER FRONT ASSY 25 A SP (25ppm) |
| Парткод: | 302L394030 |
| Деталь: | COVER FRONT TOP |
| Парткод: | 302K304020 |
| Деталь: | COVER EXIT FRONT |
| Парткод: | 302K304050 |
| Деталь: | COVER LEFT TOP |
| Парткод: | 302K304110 |
| Деталь: | COVER EXIT REAR |
| Парткод: | 302K304040 |
| Деталь: | COVER TRAY LEFT |
| Парткод: | 302K304180 |
| Деталь: | COVER EXIT TOP |
| Парткод: | 302K304190 |
| Деталь: | COVER TRAY |
| Парткод: | 302K304030 |
| Деталь: | COVER LEFT LOW |
| Парткод: | 302K304100 |
| Деталь: | Cover Right Rear |
| Парткод: | 302K304060 |
| Деталь: | PARTS COVER RIGHT TOP ASSY SP |
| Парткод: | 302K394580 |
| Деталь: | PARTS COVER REAR ASSY SP |
| Парткод: | 302K394610 |
| Деталь: | COVER FILTER REAR |
| Парткод: | 302K304200 |
| Деталь: | COVER EXIT FRONT TOP |
| Парткод: | 302K304290 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302H004560 |
| Деталь: | COVER RIGHT LOW |
| Парткод: | 302K304070 |
| Деталь: | LID CONTROLLER BOX |
| Парткод: | 302K304170 |
| Деталь: | STOPPER PAPER B |
| Парткод: | 302K304370 |
| Деталь: | LID D SUB (Original cover Standard model) |
| Парткод: | 302L302010 |
| Деталь: | WT-475 |
| Парткод: | 302K393130 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR |
| Парткод: | 7BB702308H |
| Деталь: | PLATE ORIGINAL |
| Парткод: | 303JC04200 |
| Деталь: | CUSHION ORIGINAL MAT A |
| Парткод: | 303MX02021 |
| Деталь: | PARTS PLATEN COVER UNIT |
| Парткод: | 302L394010 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302K309080 |
| Цена: | 6 500 ₽ |
| Деталь: | CURSOR END |
| Парткод: | 302K309270 |
| Цена: | 120 ₽ |
| Деталь: | CURSOR CASSETTE FRONT |
| Парткод: | 302K309130 |
| Деталь: | CURSOR CASSETTE REAR |
| Парткод: | 302K309120 |
| Деталь: | PARTS GEAR Z18 SP |
| Парткод: | 302K394380 |
| Деталь: | CT-475 |
| Парткод: | 302K393170 |
| Деталь: | FK-475(U) |
| Парткод: | 302K393110 |
| Деталь: | FK-475(E) |
| Парткод: | 302K393120 |
| Деталь: | PARTS ROLLER REGIST RIGHT SP |
| Парткод: | 302K394220 |
| Деталь: | PARTS GEAR REGIST Z24R SP |
| Парткод: | 302K394330 |
| Деталь: | ACTUATOR DU |
| Парткод: | 302K329040 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | TR-475 |
| Парткод: | 302K393090 |
| Деталь: | PARTS ROLLER DU SP |
| Парткод: | 302K394250 |
| Деталь: | PARTS GEAR DU Z27L SP |
| Парткод: | 302K394400 |
| Деталь: | PARTS MPF TABLE ASSY SP |
| Парткод: | 302K394470 |
| Деталь: | +BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | PARTS CONVEYING UNIT |
| Парткод: | 302K394510 |
| Деталь: | PARTS RIGHT COVER UNIT |
| Парткод: | 302K394530 |
| Деталь: | PRIMARY FEED UNIT |
| Парткод: | 302K394480 |
| Цена: | 5 900 ₽ |
| Деталь: | PARTS ROLLER REGIST LEFT SP |
| Парткод: | 302K394230 |
| Деталь: | PARTS GEAR REGIST Z28L-Z18L SP |
| Парткод: | 302K394310 |
| Деталь: | ACTUATOR MPF |
| Парткод: | 302K308020 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | PARTS GEAR MPF Z28 SP |
| Парткод: | 302K394320 |
| Деталь: | MPF ROLLER (service only) |
| Парткод: | 302K394460 |
| Цена: | 4 200 ₽ |
| Деталь: | SEPARATION Pad (service only) |
| Парткод: | 302K394490 |
| Деталь: | PARTS FEED UNIT ASSY SP |
| Парткод: | 302K394540 |
| Деталь: | REGIST CLEANER |
| Парткод: | 302K394450 |
| Цена: | 750 ₽ |
| Деталь: | PARTS MPF UNIT |
| Парткод: | 302K394500 |
| Деталь: | MPF ROLLER-PAD SET (for customer) |
| Парткод: | 302K394620 |
| Деталь: | COVER OPERATION LOW |
| Парткод: | 302K305020 |
| Деталь: | PARTS PWB PANEL MAIN ASSY SP |
| Парткод: | -302K394050 |
| Деталь: | PARTS LCD COLOR SP |
| Парткод: | -302K394170 |
| Деталь: | SHEET OPERATION RIGHT E |
| Парткод: | 302K305310 |
| Деталь: | SHEET OPERATION RIGHT G |
| Парткод: | 302K305350 |
| Деталь: | SHEET OPERATION RIGHT F |
| Парткод: | 302K305360 |
| Деталь: | SHEET OPERATION RIGHT I |
| Парткод: | 302K305370 |
| Деталь: | SHEET OPERATION RIGHT S |
| Парткод: | 302K305380 |
| Деталь: | SHEET OPERATION RIGHT P(B) |
| Парткод: | 302K305390 |
| Деталь: | SHEET OPERATION RIGHT N |
| Парткод: | 302K305400 |
| Деталь: | SHEET OPERATION RIGHT R |
| Парткод: | 302K305410 |
| Деталь: | SHEET OPERATION LEFT E |
| Парткод: | 302K305320 |
| Деталь: | SHEET OPERATION LEFT G |
| Парткод: | 302K305440 |
| Деталь: | SHEET OPERATION LEFT F |
| Парткод: | 302K305450 |
| Деталь: | SHEET OPERATION LEFT I |
| Парткод: | 302K305460 |
| Деталь: | SHEET OPERATION LEFT S |
| Парткод: | 302K305470 |
| Деталь: | SHEET OPERATION LEFT P(B) |
| Парткод: | 302K305480 |
| Деталь: | SHEET OPERATION LEFT N |
| Парткод: | 302K305490 |
| Деталь: | SHEET OPERATION LEFT R |
| Парткод: | 302K305500 |
| Деталь: | PARTS OPERATION UNIT SP |
| Парткод: | 302K394420 |
| Деталь: | SOLENOID ASSY |
| Парткод: | 302F944090 |
| Деталь: | MOTOR REVERSE |
| Парткод: | 302HN44100 |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 302K394240 |
| Деталь: | ACTUATOR EXIT OVERFLOW |
| Парткод: | 302K328060 |
| Деталь: | ACTUATOR EXIT UPPER SWITCH |
| Парткод: | 302K328070 |
| Деталь: | PARTS GEAR Z74R-Z22S EXIT SP |
| Парткод: | 302K394340 |
| Деталь: | PARTS GEAR Z22S EXIT SP |
| Парткод: | 302K394350 |
| Деталь: | PARTS GEAR Z25S EXIT INPUT SP |
| Парткод: | 302K394360 |
| Деталь: | PARTS SWITCH EXIT PAPER EMPTY SP |
| Парткод: | 302K394180 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | ARM ACTUATOR EXIT |
| Парткод: | 302K328160 |
| Деталь: | TRAY EJECT |
| Парткод: | 302K328300 |
| Деталь: | PARTS EXIT UNIT |
| Парткод: | 302K394520 |
| Деталь: | PARTS PWB DRIVE ASSY SP |
| Парткод: | 303M894010 |
| Деталь: | ACTUATOR TIMING |
| Парткод: | 303M824190 |
| Деталь: | WIRE INTERFACE |
| Парткод: | 303M846010 |
| Деталь: | GEAR,LEADING FEED JOINT |
| Парткод: | 36211500 |
| Деталь: | GEAR Z21 CONT |
| Парткод: | 302H731700 |
| Деталь: | ACTUATOR ORIGINAL SET |
| Парткод: | 303M807060 |
| Деталь: | ACTUATOR FEED |
| Парткод: | 303M824090 |
| Деталь: | PARTS GUIDE READING ASSY SP |
| Парткод: | 303M894080 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | LABEL CAUTION ENG |
| Парткод: | 303M834090 |
| Деталь: | LABEL CAUTION SET 3NATIONS |
| Парткод: | 303M834120 |
| Деталь: | LABEL CAUTION SET 4NATIONS |
| Парткод: | 303M834130 |
| Деталь: | FEED ROLLER (DP) (service only) |
| Парткод: | 303M894020 |
| Деталь: | PARTS COVER PF ASSY SP |
| Парткод: | 303M894050 |
| Деталь: | MC-475 |
| Парткод: | 302K393140 |
| Деталь: | DK-475 |
| Парткод: | 302K393030 |
| Деталь: | PARTS PWB ENGINE ASSY SP |
| Парткод: | 302K394040 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302K394010 |
| Деталь: | PARTS PWB MAIN ASSY SP EU |
| Парткод: | 302K394020 |
| Деталь: | HEATER DEHUMIDIFIER 120 |
| Парткод: | 302K302430 |
| Деталь: | HEATER DEHUMIDIFIER 240 |
| Парткод: | 302K302440 |
| Деталь: | PARTS HVU SP |
| Парткод: | 302K394140 |
| Деталь: | PARTS LVU SUB 100 SP |
| Парткод: | 302K394150 |
| Деталь: | PARTS LVU SUB 200 SP |
| Парткод: | 302K394160 |
| Деталь: | FFC ENGINE-HVU |
| Парткод: | 302K346370 |
| Деталь: | FFC ENGINE-MAIN |
| Парткод: | 302K346380 |
| Деталь: | SW.SEESAW |
| Парткод: | 7SC010105+++H01 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | PUSH SWITCH 03 SN /SW-192 N |
| Парткод: | 5ESP03090001 +01 |
| Деталь: | PLATE SIZE DETECTION |
| Парткод: | 302K309410 |
| Деталь: | +BIND TT S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | GEAR Z30H |
| Парткод: | 302F914160 |
| Деталь: | GEAR Z21 CONT |
| Парткод: | 302H731700 |
| Деталь: | GEAR Z34L MIDDLE |
| Парткод: | 302H731730 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 303M894090 |
| Деталь: | MOTOR IMAGE |
| Парткод: | 302KY44010 |
| Деталь: | MOTOR ROTARY |
| Парткод: | 302KY44090 |
| Деталь: | GEAR 20/65 IDLE |
| Парткод: | 303H622331 |
| Деталь: | GEAR Z32S LIFT |
| Парткод: | 303LL31260 |
| Деталь: | PARTS PWB LED ASSY SP |
| Парткод: | 303M894100 |
| Деталь: | PARTS ROLLER REGISTRATION SP |
| Парткод: | 303M894110 |
| Деталь: | PARTS ROLLER CONVEYING A SP |
| Парткод: | 303M894120 |
| Деталь: | PARTS ROLLER CONVEYING B SP |
| Парткод: | 303M894130 |
| Деталь: | ACTUATOR REGISTRATION |
| Парткод: | 303M824110 |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 303M894140 |
| Деталь: | PARTS ROLLER LOOP SP |
| Парткод: | 303M894150 |
| Деталь: | PARTS GEAR Z41L Z58L Z76L SP |
| Парткод: | 303M894160 |
| Деталь: | PARTS GEAR Z32R SP |
| Парткод: | 303M894170 |
| Деталь: | PARTS GEAR Z38L SP |
| Парткод: | 303M894180 |
| Деталь: | PARTS GEAR Z33L SP |
| Парткод: | 303M894190 |
| Деталь: | PARTS GEAR Z34R Z26S SP |
| Парткод: | 303M894200 |
| Деталь: | PARTS GEAR Z29R SP |
| Парткод: | 303M894210 |
| Деталь: | PARTS GEAR Z29L ONEWAY SP |
| Парткод: | 303M894220 |
| Деталь: | PARTS GEAR Z39S SP |
| Парткод: | 303M894240 |
| Деталь: | PARTS GEAR LF Z29S SP |
| Парткод: | 303M894250 |
| Деталь: | GEAR,LEADING FEED JOINT |
| Парткод: | 36211500 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | RETARD GUIDE (DP) (service only) |
| Парткод: | 303M894030 |
| Цена: | 500 ₽ |
| Деталь: | RETARD ROLLER (DP) (service only) |
| Парткод: | 303M894040 |
| Цена: | 2 700 ₽ |
| Деталь: | PARTS GUIDE PF ASSY SP |
| Парткод: | 303M894070 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | PARTS MOTOR-BL W30 SP |
| Парткод: | 302K394200 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44010 |
| Деталь: | DR-475 |
| Парткод: | 302K393080 |
| Деталь: | COVER ISU FRONT |
| Парткод: | 302K304120 |
| Деталь: | COVER ISU LEFT |
| Парткод: | 302K304130 |
| Деталь: | PARTS COVER ISU RIGHT ASSY A SP |
| Парткод: | 302K394590 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302K304150 |
| Деталь: | PARTS MOTOR ISU SP |
| Парткод: | 302K394210 |
| Деталь: | PARTS ISU |
| Парткод: | 302K393150 |
| Деталь: | SWITCH RELEASE |
| Парткод: | 302K317250 |
| Деталь: | GEAR Z54 |
| Парткод: | 302K317350 |
| Деталь: | PARTS GEAR Z18-Z63R SP |
| Парткод: | 302K394370 |
| Деталь: | PARTS CONTACT-GLASS ASSY(I) SP |
| Парткод: | 302K394560 |
| Деталь: | PARTS CONTACT-GLASS ASSY(C) SP |
| Парткод: | 302K394550 |
| Деталь: | PARTS MOUNT LED ASSY |
| Парткод: | 302K393160 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | FFC MAIN-CCD |
| Парткод: | 302K346410 |
| Деталь: | FFC MAIN-LED LAMP |
| Парткод: | 302K346400 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR |
| Парткод: | 7BB702308H |
| Деталь: | +PAN M SCREW WITH SW W 3X8 R |
| Парткод: | 7BB606308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
Коды ошибок
0030
0060
0070
0100
0120
0130
0140
0150
0160
0170
0180
0320
0800
0830
0840
0870
0920
1010
1020
1030
1800
1900
2000
2010
2600
3100
3200
3500
3600
4000
4010
4100
4700
6000
6020
6030
6050
6400
7800
7810
7900
7910
8030
8040
8140
8210
8320
8330
8350
8360
8460
8800
8830
8990
9000
9060
9500
9510
9520
9530
9540
9550
F000
F010, F011, F012, F013
F040
F050
Описание
| Error code: | 0030 |
| Description: | FAX control PWB system error Processing with the fax software was disabled due to a software problem. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Reinstall the fax software. 3. Replace the FAX control PWB. |
| Error code: | 0060 |
| Display: | FUSER MOTOR |
| Description: | Engine PWB mismatch Unmatching engine and engine sub boards. Defective engine subboard |
| Causes: | Defective engine sub PWB. |
| Remedy: | Engine PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Replace the engine PWB. |
| Error code: | 0070 |
| Description: | FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX control PWB (The FAX PWB installed will not be the one designed for the machine.) 1. Install the FAX system designed for the model. 2. Reinstall the fax software. |
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0130 |
| Description: | There is a problem with Thermistor for Print Heater. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0140 |
| Description: | There is a problem with Thermistor for dryer. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0180 |
| Description: | Even though the machine carries out the regular movement, the output of Maintenance Liquid Pump Sensor does not reach the expected value. |
| Causes: | Maintenance Liquid Pump Motor has a problem. Maintenance Liquid Pump Sensor has a problem. Maintenance Liquid Pump Magnet has dropped out. Wiring or Flexible Cable has short circuitted |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Maintenance Liquid Pump Motor replacement Maintenance Liquid Pump Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0320 |
| Description: | I/O CPU communication error A communication error is detected 10 times in succession. |
| Causes: | Defective PWB. |
| Remedy: | Defective PWB. Replace the main PWB or the engine PWB and check for correct operation.(see page 1- 5-33,1-5-34) |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0830 |
| Description: | FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX software 1. Reinstall the fax software. FAX control PWB 1. Execute initializing by U600.(Refer to the FAX service manual) 2. Replace the FAX control PWB. |
| Error code: | 0840 |
| Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
| Causes: | The battery is disconnected from the main PWB Defective main PWB. |
| Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
| Error code: | 0870 |
| Description: | PCFAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. |
| Causes: | Improper installation FAX control PWB. Defective FAX control PWB or main PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Replace the FAX control PWB. HDD Execute U024 to initialize the HDD. Main PWB Replace the main PWB. |
| Error code: | 0920 |
| Description: | Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Execute initializing by U600 (Refer to the FAX service manual). 2. Replace the FAX control PWB. |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1800 |
| Description: | Paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| Remedy: | Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2000 |
| Description: | DDA Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 2010 |
| Display: | Paper loaded askew. Press Load/Eject and reload the paper. |
| Description: | Main motor startup error Main motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Main motor. Engine PWB |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC13) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 3100 |
| Description: | Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor. |
| Causes: | Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective ISC PWB. Defective main PWB. |
| Remedy: | The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary. Scanner motor 1. To check the scanner motor, execute U073. 2. Move the scanner by the hand to check whether it is unusually difficult to move. 3. Check that the optical wire rope is not disengaged and engage the wire. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the scanner motor. Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and ISC PWB (YC8) 3. Replace the home position sensor. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3200 |
| Description: | Exposure lamp error When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LED lamp PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and main PWB (YC11) Defective LED lamp PWB. Replace the LED lamp PWB and check for correct operation. Defective ISC PWB. Replace the ISC PWB and check for correct operation. Defective CCD PWB. Replace the ISU and check for correct operation. Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | 3500 |
| Description: | Communication error between scanner and ASIC An error code is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective ISC PWB. Defective main PWB. |
| Remedy: | ISC PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ISC PWB (YC3) and Main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3600 |
| Description: | Scanner sequence error |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Execute U021 memory initializing. 2. Replace the ISC PWB and execute U411. |
| Error code: | 4000 |
| Display: | Supplies Drum End Soon. |
| Description: | Command Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 4010 |
| Description: | Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and engine PWB (YC11) Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 4100 |
| Description: | BD initialization error BD is not detected within 1 s after polygon motor stabilized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective APC PWB. Defective BD PWB. Defective main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. BD PWB and APC PWB (YC1) APC PWB (YC2) and main PWB (YC103) Defective BD PWB. Defective APC PWB. Replace the laser scanner unit. Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | 4700 |
| Display: | Supplies WT Box End Soon |
| Description: | VIDEO_ASIC device error Communication with the video ASIC has failed 5 times successively. After writing to the VIDEO ASIC, the error that the reading value from the same address does not match occurs 8 times successively. |
| Causes: | Engine PWB. Main PWB |
| Remedy: | Main PWB 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Check that the connectors on the main PWB are properly connected, and if not, re-connect them. 3. Replace the main PWB. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6050 |
| Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
| Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 7900 |
| Display: | Jam Manual Feed Pull out the jammed paper from Manual Feed and press Start |
| Description: | Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum unit. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and engine PWB (YC15) Defective drum unit. Replace the drum unit. |
| Error code: | 7910 |
| Description: | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit and engine PWB (YC12) Defective developer unit. Replace the developer unit. |
| Error code: | 8030 |
| Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8040 |
| Description: | Belt problem (document finisher) The belt sensor does not turn on/off within specified time of the belt solenoid turning on. |
| Causes: | Defective connector cable or poor contact in the connector. Defective belt sensor. Defective belt solenoid. Defective DF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Belt sensor and DF main PWB (CN10) Belt solenoid and DF main PWB (CN21) Defective belt sensor. Replace the belt sensor. Defective belt solenoid. Replace the belt solenoid. Defective DF main PWB. Replace the DF main PWB and check for correct operation. |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8320 |
| Description: | CF adjustment motor error When initial operation, CF adjustment sensor does not turn on within 2.5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF adjustment sensor 1, 2. Defective CF adjustment motor 1, 2. Defective CF main PWB. |
| Remedy: | CF adjustment motor1,2 1. Execute U240 Booklet - Bundle Up / Down to check the finisher operation. 2. Manipulate the fold moving belt up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold moving belt. (Check if the belt is bent.) 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment motor 1,2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF adjustment motor1,2 CF adjustment sensor1,2 1. Execute U241 Booklet - bundle Up / Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment sensor 1,2 and CF main PWB (YC20) 4. Replace the CF adjustment sensor1,2. CF main PWB Replace the CF main PWB. |
| Error code: | 8330 |
| Description: | CF blade motor error When initial operation, CF blade sensor does not turn on within 1500 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF blade sensor. Defective CF blade motor. Defective CF main PWB. |
| Remedy: | CF blade motor 1. Execute U240 Booklet - Blade to check the finisher operation. 2. Manipulate the fold blade up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold blade. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade motor and CF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF blade motor. CF blade sensor 1. Execute U241 Booklet - Blade HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade sensor and CF main PWB (YC20) 4. Replace the CF blade sensor. CF main PWB Replace the CF main PWB |
| Error code: | 8350 |
| Description: | CF side registration motor 1 error When initial operation, CF side registration sensor 1 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 1. Defective CF side registration motor 1. Defective CF main PWB |
| Remedy: | CF side registration motor 1 1. Execute U240 Booklet - Width Test to check the finisher operation. 2. Manipulate the side registration lower guide back and forth to check it can smoothly operable. 3. Check that the drive from the motor reaches the side registration lower guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 1 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor 1. CF side registration sensor 1 1. Execute U241 Booklet - Width Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 1 and CF main PWB (YC20) 4. Replace the CF side registration sensor 1. CF main PWB Replace the CF main PWB |
| Error code: | 8360 |
| Description: | CF main motor error During driving the motor, the lock signal is detected for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF main motor. Defective CF main PWB. |
| Remedy: | CF main motor 1. Execute U240 Booklet - Folding to check the finisher operation. 2. Manipulate the conveying roller to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main motor and CF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF main motor. CF main PWB Replace the CF main PWB |
| Error code: | 8460 |
| Description: | EEPROM problem (document finisher) Reading from or writing to EEPROM cannot be performed. |
| Causes: | Defective EEPROM or DF main PWB. |
| Remedy: | Replace the DF main PWB and check for correct operation. |
| Error code: | 8800 |
| Description: | Document finisher main program error Document finisher main program error at power up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8830 |
| Description: | Bridge communication error (document finisher) A communication error is detected 10 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective bridge PWB. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Engine PWB (YC19) and DF relay PWB (YC2) DF relay PWB (YC4) and bridge PWB (YC5) Defective bridge PWB. Replace the bridge PWB and check for correct operation. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 8990 |
| Description: | Finisher setup error In case the bridge (AK) is not installed while the DF is connected. (35/40 ppm model only) |
| Causes: | Bridge unit Document finisher. DF main PWB. Engine PWB |
| Remedy: | Finisher 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DF main PWB - Engine PWB(YC24): 30 ppm model - Engine PWB(YC31): 35/40 ppm models 2. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. DF main PWB 1. Check EEPROM mount and correct it. 2. Replace the DF main PWB. |
| Error code: | 9000 |
| Description: | Document processor communication error Communication with the document processor is not possible. |
| Causes: | Defective connector cable or poor contact in the connector Defective PWB. |
| Remedy: | DP main PWB 1. Check that the versions of the main unit firmware and the DP firmware are identical. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP main PWB(YC1) and ISC PWB(YC12) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP main PWB ISC PWB Replace the ISC PWB. |
| Error code: | 9060 |
| Description: | DP EEPROM error Mismatch of reading data from two locations occurs 3 times successively. Mismatch between writing data and reading data occurs 3 times successively. |
| Causes: | Defective DP main PWB. Device damage of EEPROM. |
| Remedy: | DP main PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the EEPROM has been properly installed. 3. Replace the DP main PWB Device damage of EEPROM Contact the Service Support. |
| Error code: | 9500 |
| Description: | ISC PWB error A |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC PWB 4. Contact the Service Support. |
| Error code: | 9510 |
| Description: | ISC PWB error B |
| Causes: | Main PWB. DP SHD PWB. |
| Remedy: | Main PWB DP SHD PWB 1. Reinsert the connector if its connection is loose. DP relay PWB (YC2) and DP SHD PWB (YC3) 2. Replace the main PWB. 3. Replace the DP SHD PWB. 4. Contact the Service Support. |
| Error code: | 9520 |
| Description: | ISC PWB error C |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC main PWB 4. Contact the Service Support. |
| Error code: | 9530 |
| Description: | Machine No.backup error C |
| Causes: | IPU PWB error |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | 9540 |
| Description: | Backup data error The machine may not be recovered or may have trouble in its function with changes of the internal data when replacing some the parts at the same time. |
| Causes: | PWBs |
| Remedy: | Reattach the parts below in case of replacing 2 or more of them at the same time. Affected parts : Memory, PWBs * Do not replace two or more of the parts at the same time. * And, do not either execute the following works when replacing the above parts. Replace the drum unit or the developing unit. Replace the drum unit for the one color with another in the same machine. |
| Error code: | 9550 |
| Description: | Machine No.backup error E |
| Causes: | IPU PWB error |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010, F011, F012, F013 |
| Description: | Main PWB checksum error |
| Causes: | Defective main PWB. |
| Remedy: | Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
