Kyocera TASKalfa 356ci
Рейтинг
Снят с производства
Тип устройства
МФУ
Технология печати
лазерная
Макс. формат
A4
Скорость печати
A4
35
Цветность печати
цветная
Общие характеристики |
|
---|---|
Технология печати |
лазерная |
Тип |
лазерный/светодиодный |
Цветность печати |
цветная |
Размещение |
напольный |
Тип устройства |
МФУ |
Сканер |
|
Копир |
|
Факс |
|
Печать фотографий |
|
Телефон |
|
Макс. формат |
A4 |
Принтер |
|
Макс, длина отпечатка |
356 |
Количество цветов |
4 |
Пигментные чернила |
|
Печать без полей |
|
Время разогрева |
24 |
Макс, ширина отпечатка |
216 |
Прямая печать |
|
Двусторонняя печать |
|
Макс, разрешение для ч/б печати |
|
По Y | 600 |
По X | 1 200 |
По Y | 1 200 |
Скорость ч/б печати |
|
A4 | 35 |
Макс, разрешение для цветной печати |
|
По X | 9 600 |
Время выхода первого отпечатка |
|
Ч/б | 5,5 |
Цветн, | 6,5 |
Копир |
|
Время выхода первой копии |
7,3 |
Макс, количество копий за цикл |
999 |
Шаг масштабирования |
0,01 |
Значение масштаба |
|
Максимальное | 4 |
Минимальное | 0,25 |
Макс, разрешение (ч/б) |
|
По X | 600 |
По Y | 600 |
По X | 400 |
Сканер |
|
Отправка изображения по e-mail |
|
Стандарт TWAIN |
|
Емкость устройства автоподачи оригиналов |
75 |
Слайд-адаптер |
|
Устройство автоподачи оригиналов |
одностороннее |
Макс. формат оригинала |
A4 |
Оттенки серого |
256 |
Тип сканера |
планшетный/протяжный |
Макс, размер сканирования |
|
По Y | 356 |
По X | 216 |
Разрешение сканера |
|
По Y | 400 |
По Х | 600 |
Скорость сканирования |
|
Ч/б | 60 |
Цветн, | 40 |
Расходные материалы |
|
Ресурс цветного картриджа/тонера |
12 000 |
Ресурс ч/б картриджа/тонера |
18 000 |
Количество картриджей |
4 |
Печать на: |
|
CD/DVD | |
Фотобумаге | |
Рулоне | |
Этикетках | |
Глянцевой бумаге | |
Матовой бумаге | |
Конвертах | |
Карточках | |
Пленках | |
Плотность бумаги |
|
Максимальная | 220 |
Минимальная | 60 |
Факс |
|
Макс, скорость передачи данных |
33,6 Кбит/с |
PC Fax |
|
Телефон |
|
АОН |
|
Беспроводная трубка |
|
Проводная трубка |
|
Спикерфон |
|
Стандарт DECT |
|
Автоответчик |
|
Caller ID |
|
Шрифты и языки управления |
|
Языки управления |
|
PPDS | |
PostScript 2 | |
PCL 5c | |
PCL 6 | |
PostScript | |
PostScript 3 | |
PCL 5e | |
Количество установленных шрифтов |
|
PCL | 93 |
PostScript | 136 |
Лотки |
|
Емкость лотка ручной подачи |
100 |
Подача бумаги |
|
Максимальная | 3 100 |
Стандартная | 600 |
Вывод бумаги |
|
Стандартный | 500 |
Финишер |
|
Сортер |
|
Брошюровщик |
|
Степлер |
|
Интерфейсы |
|
Ethernet (RJ-45) |
|
Веб-интерфейс |
|
USB |
|
Bluetooth |
|
LPT |
|
AirPrint |
|
Инфракрасный порт |
|
RS-232 |
|
Устройство для чтения карт памяти |
|
Wi-Fi |
|
FireWire (IEEE 1394) |
|
Количество свободных слотов расширения |
2 |
Версия USB |
2,0 |
Память/Процессор |
|
Макс, объем памяти |
2 048 |
Объем памяти |
1 024 |
Процессор |
Freescale QorIQ P1022 (Dual Core) |
Частота процессора |
800 |
Дополнительная информация |
|
Работа от аккумулятора |
|
Экран |
|
Поддержка ОС |
|
DOS | |
Windows | |
Mac OS | |
Linux | |
Потребляемая мощность |
|
В режиме ожидания | 110 |
При работе | 752 |
Уровень шума |
|
В режиме ожидания | 25,4 |
При работе | 49,6 |
Габариты |
|
Ширина |
550 |
Глубина |
507 |
Высота |
613 |
Вес |
48 |
Модули
DP Covers
Scanner Section (30ppm(A4),32ppm(Letter))
Developer & Image Formation Section
DP Drive Section & Electrical Components
Electrical Components 3 (30ppm(A4),32ppm(Letter))
Paper Feed Section 1
Electrical Components 1
DP Paper Conveying Section 2
Frames Base
DP Paper Feed Section
PAPER CASSETTE
Frames Top
FRAME L
PANEL
Electrical Components 4
Operation Section (30ppm(A4),32ppm(Letter))
DP Paper Conveying Section 1
Frames Right
Exit Section 1
Frames Left
Scanner Section (35ppm(A4),37ppm(Letter)/40ppm(A4),42ppm(Letter))
Exit Section 2
Frames Front
Operation Section (35ppm(A4),37ppm(Letter)/40ppm(A4),42ppm(Letter))
DP ASSY SP
Paper Conveying Section 1
DP Table Assy
DRIVE SECTION 2
Frames Rear 1
CASSETTE ASSEMBLY
Paper Conveying Section 2
ELECTRICAL COMPONENTS 2
Laser Scanner Section
(Узел переноса)
Electrical Components 3 (40ppm(A4),42ppm(Letter))
TRANSFER SECTION
PAPER FEED
Frames Rear 2
Fuser Section
Electrical Components 3 (35ppm(A4),37ppm(Letter))
Paper Feed Section 3
DP Frames
Drive Section 1
Covers 1
Covers 2
PAPER FEED SECTION 2
Детали Laser Scanner Section
Деталь: | COVER FRONT |
Парткод: | 303R304010 |
Деталь: | COVER FRONT B |
Парткод: | 303R304040 |
Деталь: | COVER REAR A |
Парткод: | 303R304020 |
Деталь: | COVER REAR B |
Парткод: | 303R304030 |
Деталь: | ARM PF COVER |
Парткод: | 303R302040 |
Деталь: | STOPPER 4 |
Парткод: | 302FZ25740 |
Деталь: | LABEL SIZE DIRECTION |
Парткод: | 303R334010 |
Деталь: | PLATE ORIGINAL |
Парткод: | 302H918021 |
Деталь: | CUSHION ORIGINAL MAT A |
Парткод: | 303MX02021 |
Деталь: | SLIDER ISU |
Парткод: | 302H917450 |
Деталь: | STOPPER BUSH ISU |
Парткод: | 302KW17150 |
Деталь: | BUSH ISU |
Парткод: | 302NM17150 |
Деталь: | PARTS SENSOR OPT SP |
Парткод: | 303M894260 |
Деталь: | WIRE FFC CCD |
Парткод: | 302R446100 |
Деталь: | CONN.CORD ASSY S03840 CCD-LED |
Парткод: | 3V2NM46130 |
Деталь: | CONN.CORD ASSY S03841 CCD-HP |
Парткод: | 3V2NM46140 |
Деталь: | PARTS ISU TOP SP |
Парткод: | 302R694010 |
Деталь: | SPRING EARTH ISU B |
Парткод: | 302R417220 |
Деталь: | MOUNT TENSION PULLEY |
Парткод: | 3V2NM17210 |
Деталь: | PULLEY TENSION |
Парткод: | 302M417180 |
Деталь: | SPRING-COMPRESSION ISU BELT |
Парткод: | 3V2NM17600 |
Деталь: | SPRING EARTH ISU A |
Парткод: | 302R417050 |
Деталь: | PARTS MOTOR ISU SP |
Парткод: | 302LW94060 |
Деталь: | GEAR Z63R-P32 ISU |
Парткод: | 3V2NM17200 |
Деталь: | RING STOPPER/A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | BUSHING FAN |
Парткод: | 302JD19140 |
Деталь: | PIN LSU |
Парткод: | 302JD19150 |
Деталь: | SHEET FFC B |
Парткод: | 302R417110 |
Деталь: | TAPE FFC BD |
Парткод: | 302NR19260 |
Деталь: | BELT ISU |
Парткод: | 302R417040 |
Деталь: | SHAFT ISU |
Парткод: | 302R417030 |
Деталь: | FERRITE CORE |
Парткод: | 7YBFZZ65C002H01 |
Деталь: | SHEETFFCA |
Парткод: | 302R417090 |
Деталь: | LABEL CAUTION |
Парткод: | 302R434110 |
Деталь: | WIRE STOPPER |
Парткод: | 302K931080 |
Деталь: | PIN COVER |
Парткод: | 303MH04040 |
Деталь: | PIN DLP RAIL |
Парткод: | 302GR02852 |
Деталь: | ISU ASSY L SP |
Парткод: | 302R493140 |
Деталь: | MC-5195 |
Парткод: | 302R493060 |
Деталь: | MC-5215 |
Парткод: | 302R693030 |
Деталь: | DV-5195K |
Парткод: | 302R493070 |
Деталь: | DV-5205K |
Парткод: | 302R593010 |
Деталь: | DV-5215K |
Парткод: | 302R693040 |
Деталь: | DV-5195M |
Парткод: | 302R493080 |
Деталь: | DV-5205M |
Парткод: | 302R593020 |
Деталь: | DV-5215M |
Парткод: | 302R693050 |
Деталь: | DV-5195C |
Парткод: | 302R493090 |
Деталь: | DV-5205C |
Парткод: | 302R593030 |
Деталь: | DV-5215C |
Парткод: | 302R693060 |
Деталь: | DV-5195Y |
Парткод: | 302R493100 |
Деталь: | DV-5205Y |
Парткод: | 302R593040 |
Деталь: | DV-5215Y |
Парткод: | 302R693070 |
Деталь: | DK-5195 |
Парткод: | 302R493050 |
Деталь: | DK-5215 |
Парткод: | 302R693020 |
Деталь: | ACTUATOR BASE |
Парткод: | 303K502200 |
Деталь: | GUIDE WIRE A |
Парткод: | 3V2NM18070 |
Деталь: | COVER DRIVE |
Парткод: | 3V2NM18320 |
Деталь: | GEAR Z51S |
Парткод: | 3V2NM18330 |
Деталь: | GEAR Z50S |
Парткод: | 3V2NM18340 |
Деталь: | GEAR Z54S-Z33S |
Парткод: | 3V2NM18350 |
Деталь: | GEAR Z54S-Z33S B |
Парткод: | 3V2NM18500 |
Деталь: | LEVER LOOP A |
Парткод: | 3V2NM18870 |
Деталь: | PARTS SENSOR OPT SP |
Парткод: | 303M894260 |
Деталь: | PLATE EARTH MOTOR |
Парткод: | 303LJ02100 |
Деталь: | SHAFT CAM |
Парткод: | 3V2NM18840 |
Деталь: | GEAR Z32S PI |
Парткод: | 3V2NM18950 |
Деталь: | CAM LOOP |
Парткод: | 3V2NM18830 |
Деталь: | MOUNT DRIVE B |
Парткод: | 3V2NM18310 |
Деталь: | PARTS MOTOR ROTARY SP |
Парткод: | 302KY94140 |
Деталь: | GEAR Z35S |
Парткод: | 3V2NM18390 |
Деталь: | GEAR Z51S-Z17S |
Парткод: | 3V2NM18380 |
Деталь: | GUIDE WIRE B |
Парткод: | 3V2NM18080 |
Деталь: | BUSH 6 EW |
Парткод: | 302H024370 |
Цена: | 190 ₽ |
Деталь: | NYLON CLAMP 4N,NK-4N |
Парткод: | M2105020 |
Деталь: | OMEGALOCK,OLS-115 |
Парткод: | M21A7010 |
Деталь: | PARTS DRIVE ASSY A SP |
Парткод: | 302NM94230 |
Деталь: | PARTS SWITCHING REGULATOR 100V SP |
Парткод: | 302R494320 |
Деталь: | PARTS SWITCHING REGULATOR 200V SP |
Парткод: | 302R494330 |
Деталь: | SHEET LVU L |
Парткод: | 302R439190 |
Деталь: | MOUNT MAIN LOW |
Парткод: | 302R439010 |
Деталь: | PARTS PWB MAIN ASSY SP |
Парткод: | 302R494270 |
Деталь: | PARTS PWB MAIN ASSY EU SP |
Парткод: | 302R494280 |
Деталь: | PARTS,FAN COOLING CONVEYING SP |
Парткод: | 302FZ94420 |
Деталь: | HOLDER FAN MAIN |
Парткод: | 302R439150 |
Деталь: | PARTS PWB ENGINE ASSY SP |
Парткод: | 302R494260 |
Деталь: | MOUNT SPRING HV |
Парткод: | 302R439550 |
Деталь: | SPRING HV SLEEVE R |
Парткод: | 302R439590 |
Деталь: | SPRING HV MAG R |
Парткод: | 302R439600 |
Деталь: | SPRING HV MAIN R |
Парткод: | 302R439610 |
Деталь: | SPRING TRANS 2T |
Парткод: | 302R439480 |
Деталь: | SPRING TCL |
Парткод: | 302R439680 |
Деталь: | SPRING MID TRANS |
Парткод: | 302R439580 |
Деталь: | LID SPRING HV |
Парткод: | 302R439670 |
Деталь: | SPRING HV SLEEVE R4 |
Парткод: | 302R439620 |
Деталь: | SPRING HV MAG R4 |
Парткод: | 302R439630 |
Деталь: | SPRING HV MAIN R4 |
Парткод: | 302R439640 |
Деталь: | BRACKET HVU2 |
Парткод: | 302R439470 |
Деталь: | PARTS FAN COOLING LSU 60 SP |
Парткод: | 302LC94380 |
Деталь: | SPRING HV PT PB |
Парткод: | 302R439500 |
Деталь: | SPRING HV PT CLN |
Парткод: | 302R439490 |
Деталь: | SPRING HV BK 1T |
Парткод: | 302R439510 |
Деталь: | SPRING HV M 1T |
Парткод: | 302R439520 |
Деталь: | SPRING HV C 1T |
Парткод: | 302R439530 |
Деталь: | SPRING HV Y 1T |
Парткод: | 302R439540 |
Деталь: | ACCESS.CLAMP |
Парткод: | 7YZM390011++H01 |
Деталь: | ACCESS.SPACER |
Парткод: | 7YZM590001++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610002++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | GEAR FEED Z26L |
Парткод: | 302R406070 |
Деталь: | PULLEY FEED ASSY |
Парткод: | 302F906230 |
Цена: | 750 ₽ |
Деталь: | GEAR FEED Z30H |
Парткод: | 302F906280 |
Деталь: | PULLEY PICKUP ASSY |
Парткод: | 302HN06080 |
Цена: | 480 ₽ |
Деталь: | SHAFT PULLEY FEED |
Парткод: | 302K306100 |
Деталь: | BUSH 4 |
Парткод: | 302K306460 |
Деталь: | HOLDER PICKUP |
Парткод: | 302R406020 |
Деталь: | BUSH PICKUP HOLDER |
Парткод: | 302R406030 |
Деталь: | BUSH DRIVE 8 |
Парткод: | 302K331230 |
Деталь: | RETARD ROLLER ASSY |
Парткод: | 302F909171 |
Цена: | 900 ₽ |
Деталь: | FRAME FEED UPPER |
Парткод: | 302R406010 |
Деталь: | SHAFT FEED DRIVE |
Парткод: | 302R406040 |
Деталь: | SPRING PICKUP |
Парткод: | 302R406050 |
Деталь: | ACTUATOR PAPER EMPTY |
Парткод: | 302R406060 |
Деталь: | FRAME FEED LOW |
Парткод: | 302R406100 |
Деталь: | HOLDER RETARD |
Парткод: | 302R406110 |
Деталь: | FILM RETARD |
Парткод: | 302R406120 |
Деталь: | SPRING RETARD |
Парткод: | 302R406130 |
Деталь: | FRAME FEED |
Парткод: | 302R424060 |
Деталь: | PARTS ROLLER REGIST SP |
Парткод: | 302R494390 |
Деталь: | BUSH REGIST EW |
Парткод: | 302HN24410 |
Деталь: | GEAR Z19L REG REAR |
Парткод: | 302HN24060 |
Деталь: | BUSH 6 |
Парткод: | 302K324450 |
Деталь: | SPRING EARTH REGIST R |
Парткод: | 302R424090 |
Деталь: | GEAR Z25L |
Парткод: | 302S018170 |
Деталь: | BUSH FEED DRIVE |
Парткод: | 302F931490 |
Деталь: | SHEET REGIST FEED |
Парткод: | 302NR06540 |
Деталь: | HOLDER CLEANER REGIST |
Парткод: | 302R424220 |
Деталь: | SPRING FEED EARTH A |
Парткод: | 302R424100 |
Деталь: | SPRING FEED EARTH B |
Парткод: | 302R424110 |
Деталь: | GUIDE FEED LOW LEFT |
Парткод: | 302R406600 |
Деталь: | FILM FEED LOW |
Парткод: | 302R406610 |
Деталь: | PARTS CLEANER REGIST ASSY SP |
Парткод: | 302R494120 |
Деталь: | CUT-WASHER 4 |
Парткод: | 302K924820 |
Цена: | 160 ₽ |
Деталь: | MOUNT TORQUE LIMITTER |
Парткод: | 302R424240 |
Деталь: | TORQUE-LIMITER 400 |
Парткод: | 303LL07521 |
Деталь: | STOPPER RETARD |
Парткод: | 303NG06320 |
Деталь: | PARTS PRIMARY FEED ASSY SP |
Парткод: | 302R494210 |
Деталь: | PARTS HOLDER PICK UP ASSY SP |
Парткод: | 302R494170 |
Деталь: | HOLDER RELEASE TC |
Парткод: | 302R431810 |
Деталь: | BUSH DRIVE |
Парткод: | 302HN31590 |
Деталь: | GEAR Z12L RELEASE TC |
Парткод: | 302R431850 |
Деталь: | GEAR Z47S |
Парткод: | 302R431830 |
Деталь: | WORM-WHEEL RELEASE DRIVE Z40L-Z21S |
Парткод: | 302K021480 |
Деталь: | PARTS MOTOR DC ASSY SP |
Парткод: | 302R494190 |
Деталь: | PLATE RELEASE TC |
Парткод: | 302R431820 |
Деталь: | CUT WASHER 5 |
Парткод: | 302KK04570 |
Деталь: | CASE FAN MOTOR |
Парткод: | 302R603030 |
Деталь: | PARTS,FAN IMAGE SP |
Парткод: | 302FZ94660 |
Деталь: | SEAL FAN MOTOR |
Парткод: | 302R603060 |
Деталь: | COVER FAN MOTOR |
Парткод: | 302R603170 |
Деталь: | PARTS SENSOR OPT. SP |
Парткод: | 302P794010 |
Деталь: | WIRE STOPPER |
Парткод: | 302LC25780 |
Деталь: | WIRE STOPPER |
Парткод: | 302K931080 |
Деталь: | PARTS PWB RFID ASSY SP |
Парткод: | 302R694110 |
Деталь: | SW.PUSH |
Парткод: | 7SP01000004+H01 |
Деталь: | DUCT EXIT FAN |
Парткод: | 302R433070 |
Деталь: | FAN LSU 60-25 |
Парткод: | 302GR44080 |
Цена: | 2 800 ₽ |
Деталь: | PARTS PIPE TR CLN ASSY SP |
Парткод: | 302R494150 |
Деталь: | ARM SPRING A |
Парткод: | 3V2NM18890 |
Деталь: | SPRING-COMPRESSION ARM B |
Парткод: | 3V2NM18970 |
Деталь: | GUIDE LOOP |
Парткод: | 3V2NM18120 |
Деталь: | ARM SPRING B |
Парткод: | 3V2NM18940 |
Деталь: | SPRING-COMPRESSION ARM A |
Парткод: | 3V2NM18960 |
Деталь: | FRICTION PLATE LF |
Парткод: | 3HK07240 |
Деталь: | LABEL LOOP |
Парткод: | 3V2NM18980 |
Деталь: | GUIDE PF |
Парткод: | 303R307020 |
Деталь: | ACTUATOR ORIGINAL |
Парткод: | 3V2NM18750 |
Деталь: | ACTUATOR PF |
Парткод: | 3V2NM18790 |
Деталь: | SPRING-TORSION PF |
Парткод: | 3V2NM18620 |
Деталь: | HOOK PAPER FEED R |
Парткод: | 3V2NM18170 |
Деталь: | SPRING HOOK |
Парткод: | 3V2NM18760 |
Деталь: | HOOK PAPER FEED F |
Парткод: | 3V2NM18160 |
Деталь: | COVER PF |
Парткод: | 303R307010 |
Деталь: | CUSHION PF |
Парткод: | 3V2NM18180 |
Деталь: | FRICTION PLATE STOPPER PAPER |
Парткод: | 3V2NM18580 |
Деталь: | PULLEY FEED PF |
Парткод: | 303NJ06070 |
Деталь: | SHAFT GUIDE PULLEY |
Парткод: | 302R409380 |
Деталь: | STOPPER 3/2BT1107 A4 |
Парткод: | 5MVX111DN007 |
Деталь: | FOOT |
Парткод: | 302MV02190 |
Деталь: | LEVER FEED ROLLER |
Парткод: | 3V2NM18130 |
Деталь: | HOLDER PICKUP B |
Парткод: | 3V2NM18190 |
Деталь: | GEAR PICKUP 18 |
Парткод: | 3V2NM18610 |
Деталь: | GEAR Z13S |
Парткод: | 3V2NM18632 |
Деталь: | SHAFT PICKUP |
Парткод: | 3V2NM18640 |
Деталь: | STOPPER PAPER |
Парткод: | 3V2NM18650 |
Деталь: | PARTS PULLEY PICKUP ASSY SP |
Парткод: | 302R494420 |
Деталь: | SHAFT ROLLER PF |
Парткод: | 3V2NM18690 |
Деталь: | GEAR Z18S FEED ROLLER |
Парткод: | 3V2NM18710 |
Деталь: | SPRING-TORSION LF |
Парткод: | 3V2NM18780 |
Деталь: | PULLEY PF |
Парткод: | 3V2NM18800 |
Деталь: | BUSH 4 |
Парткод: | 302K306460 |
Деталь: | BUSH SCREW |
Парткод: | 302H702590 |
Деталь: | COLLAR PF |
Парткод: | 3HK07270 |
Деталь: | COLLAR S SPRING |
Парткод: | 3V2NM07080 |
Деталь: | RING STOPPER/A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | PARALLEL PIN 2.0X10 |
Парткод: | 7BP512010B0CH01 |
Деталь: | PARTS PULLEY PAPER FEED ASSY SP |
Парткод: | 302R494430 |
Деталь: | PAD SEPARATION |
Парткод: | 302LW07100 |
Деталь: | CUSHION PAD |
Парткод: | 302LW07120 |
Деталь: | PAD FRONT SEP |
Парткод: | 303K507102 |
Деталь: | MOUNT PAD |
Парткод: | 303LJ07030 |
Деталь: | FILM FRONT SEP |
Парткод: | 303LJ07090 |
Деталь: | SPRING PAD |
Парткод: | 303LJ24140 |
Деталь: | CUSHION MOUNT PAD |
Парткод: | 3V2NM18560 |
Деталь: | HOLDER PAD |
Парткод: | 3V2NM18660 |
Деталь: | GUIDE READING |
Парткод: | 3V2NM18520 |
Деталь: | SPRING READING |
Парткод: | 303LJ02070 |
Деталь: | GUIDE READING UPPER |
Парткод: | 303R324070 |
Деталь: | GUIDE LOWER RIGHT |
Парткод: | 303R324080 |
Деталь: | SPRING-COMPRESSION CONVEYING |
Парткод: | 3V2NM18550 |
Деталь: | SHAFT CONVEYING |
Парткод: | 303LJ24110 |
Деталь: | PULLEY CONVEYING |
Парткод: | 3V2NM18240 |
Деталь: | GUIDE LOWER LEFT |
Парткод: | 3V2NM18530 |
Деталь: | SPRING-COMPRESSION REGIST A |
Парткод: | 3V2NM18280 |
Деталь: | SPRING-COMPRESSION REGIST B |
Парткод: | 3V2NM18290 |
Деталь: | SHAFT CONVEYING |
Парткод: | 3V2NM18270 |
Деталь: | LEVER REGIST |
Парткод: | 303R324020 |
Деталь: | PARTS HOLDER PICKUP ASSY SP |
Парткод: | 303R394020 |
Деталь: | PARTS HOLDER PAD ASSY SP |
Парткод: | 303R394030 |
Деталь: | BASE CASSETTE |
Парткод: | 302R409010 |
Деталь: | CURSOR END |
Парткод: | 302R409020 |
Деталь: | PLATE TURN |
Парткод: | 302R409030 |
Деталь: | LEVER SIDE CURSOR |
Парткод: | 302R409040 |
Деталь: | SPRING CASSETTE EARTH |
Парткод: | 302R409050 |
Деталь: | GEAR Z13S JOINT |
Парткод: | 302R409060 |
Деталь: | INDICATER PAPER LEVEL |
Парткод: | 302R409070 |
Деталь: | LID LIFT GEAR |
Парткод: | 302R409080 |
Деталь: | SHUTTER SIZE DETECTION |
Парткод: | 302R409090 |
Деталь: | JOINT SIZE DETECTION |
Парткод: | 302R409100 |
Деталь: | PLATE BOTTOM |
Парткод: | 302R409110 |
Деталь: | REINFORCEMENT CURSOR |
Парткод: | 302R409120 |
Деталь: | LABEL PAPER LIMIT |
Парткод: | 302R434020 |
Деталь: | LABEL CASSETTE OPERATION |
Парткод: | 302R434030 |
Деталь: | RAIL INNER CASSETTE RIGHT ASSY |
Парткод: | 302R409300 |
Деталь: | RAIL INNER CASSETTE LEFT ASSY |
Парткод: | 302R409310 |
Деталь: | WORKPLATE LIFT |
Парткод: | 302NR09070 |
Деталь: | CURSOR LEFT |
Парткод: | 302NT09030 |
Деталь: | CURSOR RIGHT |
Парткод: | 302NT09040 |
Деталь: | LEVER CURSOR SET |
Парткод: | 302NT09050 |
Деталь: | SPRING CURSOR SET |
Парткод: | 302NT09060 |
Деталь: | GEAR Z48S LIFT |
Парткод: | 302NT09100 |
Деталь: | PAD BOTTOM |
Парткод: | 302F909210 |
Деталь: | SPRING LEVER CURSOR |
Парткод: | 302R409130 |
Деталь: | SPRING FIX |
Парткод: | 302HN09190 |
Деталь: | SIZE FIX |
Парткод: | 302HN09240 |
Деталь: | GEAR CASSETTE /A-49 CASSETTE A4 |
Парткод: | 5MVG127DN071 |
Деталь: | PIN,CASSETTE WORK PLATE |
Парткод: | 66007310 |
Деталь: | LABEL CASSETTE 1 |
Парткод: | 302R434040 |
Деталь: | COVER CASSETTE |
Парткод: | 302R404210 |
Деталь: | CT-5195 |
Парткод: | 302R493030 |
Деталь: | PARTS PWB KUIO ASSY SP |
Парткод: | 302K994270 |
Деталь: | RAIL KUIO |
Парткод: | 302R439070 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | BAND,RSG-130-V0(KITAGAWA) |
Парткод: | M21AH010 |
Деталь: | MOUNT PWB USB |
Парткод: | 302R605210 |
Деталь: | PARTS PWB USB HUB ASSY SP |
Парткод: | 302R694070 |
Деталь: | MOUNT USB |
Парткод: | 302R405210 |
Деталь: | SPRING USB HOLD |
Парткод: | 302K905900 |
Деталь: | PANEL UNIT, MFC9840CDW |
Парткод: | FK-5205 |
Цена: | 41 100 ₽ |
Деталь: | Электромагнитная муфта |
Парткод: | 302KV44041 |
Цена: | 900 ₽ |
Деталь: | PLATE MOUNT HV H |
Парткод: | 302R639020 |
Деталь: | FAN COOLING 40-15 |
Парткод: | 302H044120 |
Деталь: | DUCT CLUTCH A |
Парткод: | 302R433140 |
Деталь: | DUCT CLUTCH B |
Парткод: | 302R433150 |
Деталь: | SHEET HVU |
Парткод: | 302R439090 |
Деталь: | PLATE PWB HVU |
Парткод: | 302R439200 |
Деталь: | PARTS UNIT HIGH VOLTAGE MAIN SP |
Парткод: | 302R594040 |
Деталь: | PARTS UNIT HIGH VOLTAGE MAIN SP |
Парткод: | 302R694150 |
Деталь: | BUSHING FAN |
Парткод: | 302JD19140 |
Деталь: | PIN HDD |
Парткод: | 302MV39340 |
Деталь: | SPRING EARTH HDD |
Парткод: | 302MV39350 |
Деталь: | MOUNT HDD |
Парткод: | 302R439100 |
Деталь: | SEAL FRAME LONG |
Парткод: | 302LZ02070 |
Деталь: | HDD ASSY SP |
Парткод: | 302R693110 |
Деталь: | SPRING EARTH LCD |
Парткод: | 302H005620 |
Деталь: | PARTS PWB PANEL MAIN ASSY SP |
Парткод: | 302R494230 |
Деталь: | PARTS PWB OPERATION L LEFT ASSY SP |
Парткод: | 302R494240 |
Деталь: | PARTS PWB OPERATION L RIGHT ASSY SP |
Парткод: | 302R494250 |
Деталь: | COVER OPERATION |
Парткод: | 302R405010 |
Деталь: | COVER OPERATION REAR |
Парткод: | 302R405020 |
Деталь: | MOUNT OPERATION |
Парткод: | 302R405030 |
Деталь: | KEY LOGOUT |
Парткод: | 302R405080 |
Деталь: | LID HINGE |
Парткод: | 302R405120 |
Деталь: | KEY LEFT |
Парткод: | 302R405130 |
Деталь: | KEY ENERGY SAVER |
Парткод: | 302R405140 |
Деталь: | CUSHION LCD |
Парткод: | 302R405150 |
Деталь: | PLATE EARTH LCD |
Парткод: | 302R405160 |
Деталь: | FILM OPERATION R |
Парткод: | 302R405170 |
Деталь: | FILM OPERATION L |
Парткод: | 302R405180 |
Деталь: | HINGE OPERATION |
Парткод: | 302R405200 |
Деталь: | KEY START |
Парткод: | 302R405220 |
Деталь: | PARTS LCD OPERATION SP |
Парткод: | 302R494300 |
Деталь: | PARTS TABLET OPERATION SP |
Парткод: | 302R494310 |
Деталь: | WIRE FFC PANEL MAIN - OPERATION1 |
Парткод: | 302R446210 |
Деталь: | WIRE FFC PANEL MAIN - OPERATION2 |
Парткод: | 302R446230 |
Деталь: | KEY 10 |
Парткод: | 3V2NM05070 |
Деталь: | KEY STOP |
Парткод: | 3V2NM05100 |
Деталь: | KEY RESET |
Парткод: | 3V2NM05110 |
Деталь: | KEY HOME |
Парткод: | 3V2NM05130 |
Деталь: | LENS LED |
Парткод: | 3V2NM05300 |
Деталь: | KEY MENU |
Парткод: | 3V2NM05330 |
Деталь: | ACCESS.EDGING |
Парткод: | 7YZM210006++H01 |
Деталь: | COVER PANEL RIGHT |
Парткод: | 302R405040 |
Деталь: | COVER PANEL LEFT |
Парткод: | 302R405050 |
Деталь: | LID PANEL RIGHT |
Парткод: | 302R405060 |
Деталь: | LID PANEL LEFT |
Парткод: | 302R405070 |
Деталь: | HOLDER FULCRUM OPERATION |
Парткод: | 302R405100 |
Деталь: | LID OPERATION REAR |
Парткод: | 302R405110 |
Деталь: | SHEET OPERATION LEFT EN |
Парткод: | 302R405530 |
Деталь: | SHEET OPERATION RIGHT KDA EN |
Парткод: | 302R405540 |
Деталь: | SHEET OPERATION RIGHT EN |
Парткод: | 302R405520 |
Деталь: | PARTS OPERATION UNIT L SP |
Парткод: | 302R494100 |
Деталь: | HOUSING CONVEYING |
Парткод: | 3V2NM18110 |
Деталь: | ACTUATOR TIMING |
Парткод: | 3V2NM18260 |
Деталь: | SPRING-TORSION SET |
Парткод: | 302M518180 |
Деталь: | PLATE EARTH B |
Парткод: | 3V2NM18150 |
Деталь: | PLATE EARTH A |
Парткод: | 3V2NM18140 |
Деталь: | PARTS ROLLER CONVEYING B SP |
Парткод: | 303R394070 |
Деталь: | PARTS ROLLER CONVEYING A SP |
Парткод: | 303R394060 |
Деталь: | BUSH SCREW |
Парткод: | 302H702590 |
Деталь: | RING STOPPER/A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | BUSH 6 EW |
Парткод: | 302H024370 |
Цена: | 190 ₽ |
Деталь: | GEAR Z22S ONEWAY |
Парткод: | 3V2NM18400 |
Деталь: | ONE WAY CLUTCH/A-49 MPF A4 |
Парткод: | 5AAVCLTCH018 |
Деталь: | PARTS GEAR Z22S EXIT SP |
Парткод: | 302K394350 |
Деталь: | PARTS ROLLER EXIT SP |
Парткод: | 303R394080 |
Деталь: | PARTS ROLLER LOOP SP |
Парткод: | 303R394090 |
Деталь: | GEAR Z22S |
Парткод: | 3V2NM18370 |
Деталь: | GUIDE SEPARATE |
Парткод: | 3V2NM18820 |
Деталь: | LEVER SEPARATE |
Парткод: | 3V2NM18860 |
Деталь: | SPRING PICKUP |
Парткод: | 302LV06040 |
Деталь: | SHAFT PULLEY |
Парткод: | 303M824200 |
Деталь: | PULLEY CONVEYING BK |
Парткод: | 303M824210 |
Деталь: | HOLDER PULLEY |
Парткод: | 3V2NM18900 |
Деталь: | SHAFT LOOP |
Парткод: | 3V2NM18920 |
Деталь: | LEVER LOOP B |
Парткод: | 3V2NM18880 |
Деталь: | GUIDE UPPER |
Парткод: | 3V2NM18730 |
Деталь: | SHAFT GUIDE READING |
Парткод: | 303M824130 |
Деталь: | PULLEY GUIDE READING |
Парткод: | 303LL24190 |
Деталь: | STATIC ELIMINATOR |
Парткод: | 303LJ28040 |
Деталь: | GEAR Z40S |
Парткод: | 3V2NM18360 |
Деталь: | BUSH PF |
Парткод: | 3V2NM18090 |
Деталь: | ACTUATOR PUSH |
Парткод: | 3V2NM18060 |
Деталь: | SPRING-COMPRESSION RELEASE |
Парткод: | 3V2NM18100 |
Деталь: | PARTS ROLLER FEED MIDDLE SP |
Парткод: | 302R494370 |
Деталь: | BUSH 6 EW |
Парткод: | 302H024370 |
Цена: | 190 ₽ |
Деталь: | GEAR Z21L |
Парткод: | 302K923110 |
Деталь: | RING STOPPER/A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | BUSH 4-7 |
Парткод: | 302LC03230 |
Деталь: | SHAFT DRIVE BOTTLE |
Парткод: | 302R403600 |
Деталь: | BUSH SCREW |
Парткод: | 302H702590 |
Деталь: | GEAR Z25S |
Парткод: | 303MA16120 |
Деталь: | HOLDER REGIST SENSOR |
Парткод: | 302R424070 |
Деталь: | SPRING SENSOR REG EARTH |
Парткод: | 302R424150 |
Деталь: | PARTS SENSOR OPT SP |
Парткод: | 303NW94040 |
Деталь: | SHIELD ID SENSOR |
Парткод: | 302NT02010 |
Деталь: | PARTS ID SENSOR ASSY SP |
Парткод: | 302R694060 |
Деталь: | SHEET FFC |
Парткод: | 302R439180 |
Деталь: | WIRE STOPPER |
Парткод: | 302K931080 |
Деталь: | SHUTTER CLEANER ID |
Парткод: | 302R402630 |
Деталь: | FELT CLEANER ID |
Парткод: | 302HN02970 |
Деталь: | SPRING SHUTTER ID |
Парткод: | 302NR02830 |
Деталь: | PIN LSU |
Парткод: | 302R402710 |
Деталь: | SPRING PIN LSU |
Парткод: | 302R402790 |
Деталь: | PARTS SPEAKER SP |
Парткод: | 302LC94370 |
Деталь: | PARTS PWB SWITCH ASSY SP |
Парткод: | 302NG94300 |
Деталь: | SPRING FUSER |
Парткод: | 302F931270 |
Деталь: | HOLDER MAIN KEY |
Парткод: | 302NG04210 |
Деталь: | KEY POWER |
Парткод: | 302R404280 |
Деталь: | NUT FUSER |
Парткод: | 302K926050 |
Деталь: | SPRING FUSER EARTH |
Парткод: | 302R402780 |
Деталь: | PLATE EARTH EXIT |
Парткод: | 302R402620 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | PLATE EARTH FUSER |
Парткод: | 302R431460 |
Деталь: | CORE 8-16X10 |
Парткод: | 3HK27050 |
Деталь: | PARTS MOTOR FUSER ASSY SP |
Парткод: | 302R494490 |
Деталь: | SPRING FUSER DRIVE |
Парткод: | 302NR31800 |
Деталь: | GEAR Z44R-Z16S |
Парткод: | 302NR31250 |
Деталь: | GEAR Z26S |
Парткод: | 302NR31260 |
Деталь: | GUIDE WIRE ENGINE |
Парткод: | 302R439110 |
Деталь: | PARTS FAN COOLING LSU 50 SP |
Парткод: | 302K994A50 |
Деталь: | HOLDER FAN |
Парткод: | 302R433180 |
Деталь: | CAP SPRING/B-11 ENCLOSURE A4 |
Парткод: | 2FM04150 |
Деталь: | BUSH DU |
Парткод: | 302F929140 |
Деталь: | FAN COOLING 40-15 |
Парткод: | 302H044120 |
Деталь: | GEAR Z34 CONT D |
Парткод: | 302H731780 |
Деталь: | PULLEY PA |
Парткод: | 302HN24400 |
Деталь: | PARTS SOLENOID FEED SHIFT SP |
Парткод: | 302K994380 |
Деталь: | PARTS MOTOR EJECT SP |
Парткод: | 302P794060 |
Деталь: | HOUSING EXIT |
Парткод: | 302R428020 |
Деталь: | GUIDE CHANGE |
Парткод: | 302R428050 |
Деталь: | PULLEY EXIT REVERSE |
Парткод: | 302R428080 |
Деталь: | PLATE EXIT |
Парткод: | 302R428090 |
Деталь: | PARTS ROLLER EXIT JS SP |
Парткод: | 302R494340 |
Деталь: | PARTS ROLLER EXIT JS2 SP |
Парткод: | 302R494350 |
Деталь: | SHAFT EXIT DU |
Парткод: | 302R428120 |
Деталь: | PARTS ROLLER EXIT FD SP |
Парткод: | 302R494360 |
Деталь: | GEAR Z28S |
Парткод: | 302R428140 |
Деталь: | GEAR EXIT Z28S OW |
Парткод: | 302R428150 |
Деталь: | GEAR Z40R-Z25S |
Парткод: | 302R428160 |
Деталь: | BUSH EXIT 4 |
Парткод: | 302R428170 |
Деталь: | GUIDE EXIT RIGHT |
Парткод: | 302R428190 |
Деталь: | SPRING GUIDE RIGHT F |
Парткод: | 302R428200 |
Деталь: | SPRING GUIDE RIGHT R |
Парткод: | 302R428210 |
Деталь: | ACTUATOR EXIT C |
Парткод: | 302R428220 |
Деталь: | COVER FRONT |
Парткод: | 302R428230 |
Деталь: | COVER MOTOR |
Парткод: | 302R428240 |
Деталь: | SPRING EXIT EARTH A |
Парткод: | 302R428250 |
Деталь: | SPRING EXIT EARTH B |
Парткод: | 302R428260 |
Деталь: | SPRING EXIT |
Парткод: | 302R428290 |
Деталь: | CUSHION EXIT GUIDE |
Парткод: | 302R428300 |
Деталь: | SPRING CHANGE GUIDE |
Парткод: | 302R428320 |
Деталь: | PULLEY EXIT REVERSE |
Парткод: | 302R428330 |
Деталь: | LABEL EXIT |
Парткод: | 302R434130 |
Деталь: | STOPPER 3/2BT1107 A4 |
Парткод: | 5MVX111DN007 |
Деталь: | PARTS SENSOR OPT. SP |
Парткод: | 302P794010 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | WIRE EXIT UNIT |
Парткод: | 302R646340 |
Деталь: | PARTS EXIT ASSY SP |
Парткод: | 302R494050 |
Деталь: | PARTS BRACKET HV LEFT ASSY SP |
Парткод: | 302R494160 |
Деталь: | LID WIRE GUIDE |
Парткод: | 302H039270 |
Деталь: | WIRE STOPPER |
Парткод: | 302K931080 |
Деталь: | SHEET LSU |
Парткод: | 302R402300 |
Деталь: | SLIDER ISU |
Парткод: | 302H917450 |
Деталь: | STOPPER BUSH ISU |
Парткод: | 302KW17150 |
Деталь: | BUSH ISU |
Парткод: | 302NM17150 |
Деталь: | PARTS SENSOR OPT SP |
Парткод: | 303M894260 |
Деталь: | WIRE FFC CCD |
Парткод: | 302R646090 |
Деталь: | CONN.CORD ASSY S03840 CCD-LED |
Парткод: | 3V2NM46130 |
Деталь: | WIRE CCD HP |
Парткод: | 302R646720 |
Деталь: | PARTS ISU TOP SP |
Парткод: | 302R694010 |
Деталь: | SPRING EARTH ISU B |
Парткод: | 302R417220 |
Деталь: | MOUNT TENSION PULLEY |
Парткод: | 3V2NM17210 |
Деталь: | PULLEY TENSION |
Парткод: | 302M417180 |
Деталь: | SPRING-COMPRESSION ISU BELT |
Парткод: | 3V2NM17600 |
Деталь: | SPRING EARTH ISU A |
Парткод: | 302R417050 |
Деталь: | PARTS MOTOR ISU SP |
Парткод: | 302LW94060 |
Деталь: | GEAR Z63R-P32 ISU |
Парткод: | 3V2NM17200 |
Деталь: | RING STOPPER/A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | BUSHING FAN |
Парткод: | 302JD19140 |
Деталь: | PIN LSU |
Парткод: | 302JD19150 |
Деталь: | SHEET FFC B |
Парткод: | 302R617040 |
Деталь: | TAPE FFC BD |
Парткод: | 302NR19260 |
Деталь: | BELT ISU |
Парткод: | 302R417040 |
Деталь: | SHAFT ISU |
Парткод: | 302R417030 |
Деталь: | SHEETFFCA |
Парткод: | 302R617010 |
Деталь: | LABEL CAUTION AS |
Парткод: | 302R434120 |
Деталь: | LABEL CAUTION |
Парткод: | 302R434110 |
Деталь: | WIRE STOPPER |
Парткод: | 302K931080 |
Деталь: | PIN COVER |
Парткод: | 303MH04040 |
Деталь: | PIN DLP RAIL |
Парткод: | 302GR02852 |
Деталь: | ISU ASSY H SP |
Парткод: | 302R693120 |
Деталь: | CAP SPRING/B-11 ENCLOSURE A4 |
Парткод: | 2FM04150 |
Деталь: | STOPPER EARTH MIDDLE |
Парткод: | 302FZ22760 |
Деталь: | PULLEY PA |
Парткод: | 302HN24400 |
Деталь: | GUIDE EXIT PUSH |
Парткод: | 302K328090 |
Деталь: | SPRING GUIDE EXIT PUSH |
Парткод: | 302K328260 |
Деталь: | GUIDE EXIT |
Парткод: | 302R428030 |
Деталь: | COVER GUIDE EXIT |
Парткод: | 302R428040 |
Деталь: | ACTUATOR EXIT A |
Парткод: | 302R428060 |
Деталь: | ACTUATOR EXIT B |
Парткод: | 302R428070 |
Деталь: | PULLEY EXIT REVERSE |
Парткод: | 302R428080 |
Деталь: | SHAFT EXIT DU |
Парткод: | 302R428120 |
Деталь: | GUIDE EXIT UPPER |
Парткод: | 302R428180 |
Деталь: | STATIC ELIMINATOR |
Парткод: | 302R428270 |
Деталь: | ACTUATOR EXIT D |
Парткод: | 302R428280 |
Деталь: | SPRING EXIT |
Парткод: | 302R428290 |
Деталь: | CUSHION ACTUATOR |
Парткод: | 302R428310 |
Деталь: | ACTUATOR EXIT E |
Парткод: | 302R428340 |
Деталь: | RING STOPPER 4 |
Парткод: | 5MVL177DN001 |
Деталь: | CUSHION EXIT PUSH |
Парткод: | 302R428350 |
Деталь: | PARTS EXIT ASSY SP |
Парткод: | 302R494050 |
Деталь: | SPACER POSITIONING DRUM |
Парткод: | 302R402700 |
Деталь: | SPRING HOOK RAIL TRANSFER F |
Парткод: | 302R402680 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | SEAL FAN MOTOR B |
Парткод: | 302R403640 |
Деталь: | SEAL FAN MOTOR C |
Парткод: | 302R403670 |
Деталь: | FRAME MIDDLE |
Парткод: | 302R402040 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610009++H01 |
Деталь: | PARTS SENSOR OPT. SP |
Парткод: | 302P794010 |
Деталь: | HOLDER PAPER LIMIT SENSOR |
Парткод: | 302R406210 |
Деталь: | WIRE STOPPER |
Парткод: | 302K931080 |
Деталь: | DUCT DLP FRONT |
Парткод: | 302R433040 |
Деталь: | STOPPER DRUM |
Парткод: | 302R402670 |
Деталь: | SPRING DRUM STOPPER |
Парткод: | 302R402690 |
Деталь: | SPONGE DLP FRONT |
Парткод: | 302R433060 |
Деталь: | RAIL DRUM BK |
Парткод: | 302R402570 |
Деталь: | RAIL DRUM R |
Парткод: | 302R402580 |
Деталь: | RAIL DRUM L |
Парткод: | 302R402590 |
Деталь: | RAIL DRUM Y |
Парткод: | 302R402600 |
Деталь: | GEAR Z15L |
Парткод: | 302R403310 |
Деталь: | GUIDE CONTAINER A |
Парткод: | 302R402550 |
Деталь: | GUIDE CONTAINER B |
Парткод: | 302R502010 |
Деталь: | GUIDE CONTAINER C |
Парткод: | 302R602010 |
Деталь: | HOLDER SHUTTER |
Парткод: | 302R415100 |
Деталь: | HOOK SHUTTER CONT B |
Парткод: | 302K002A90 |
Деталь: | SPRING HOOK SHUTTER |
Парткод: | 302K002B80 |
Деталь: | SHUTTER PIPE UP |
Парткод: | 302R415080 |
Деталь: | SEAL SHUTTER SUPPLY |
Парткод: | 302R415240 |
Деталь: | SPRING SHUTTER SUPPLY A |
Парткод: | 302K015320 |
Деталь: | SEAL LID D DLP |
Парткод: | 302FZ14810 |
Деталь: | RAIL CONTAINER L |
Парткод: | 302R402530 |
Деталь: | DAMPER CONTAINER |
Парткод: | 302R402760 |
Деталь: | SPRING DAMPER CONT |
Парткод: | 302K002B70 |
Деталь: | DUCT FAN MIDDLE |
Парткод: | 302R433030 |
Деталь: | PARTS,FAN IMAGE SP |
Парткод: | 302FZ94660 |
Деталь: | RAIL CONTAINER C |
Парткод: | 302R402540 |
Деталь: | RAIL CONTAINER R |
Парткод: | 302R402520 |
Деталь: | MOUNT INTERLOCK SW |
Парткод: | 302R402740 |
Деталь: | INTER LOCK SWITCH |
Парткод: | 2FB27160 |
Деталь: | SHEET HARNESS |
Парткод: | 302R403720 |
Деталь: | RAIL OUTER CASSETTE RIGHT ASSY |
Парткод: | 302R409320 |
Деталь: | RAIL OUTER CASSETTE LEFT ASSY |
Парткод: | 302R409330 |
Деталь: | SEAL MAGNET |
Парткод: | 302GR04380 |
Деталь: | SPRING EARTH LCD |
Парткод: | 302H005620 |
Деталь: | PARTS LCD OPERATION SP |
Парткод: | 302NM94110 |
Деталь: | PARTS TABLET OPERATION SP |
Парткод: | 302NM94121 |
Деталь: | KEY LOGOUT |
Парткод: | 302R405080 |
Деталь: | KEY ENERGY SAVER |
Парткод: | 302R405140 |
Деталь: | CUSHION LCD |
Парткод: | 302R405150 |
Деталь: | HINGE OPERATION |
Парткод: | 302R405200 |
Деталь: | KEY START |
Парткод: | 302R405220 |
Деталь: | PARTS PWB PANEL MAIN ASSY SP |
Парткод: | 302R694120 |
Деталь: | PARTS PWB OPERATION H ASSY SP |
Парткод: | 302R694130 |
Деталь: | COVER OPERATION |
Парткод: | 302R605010 |
Деталь: | COVER OPERATION REAR |
Парткод: | 302R605020 |
Деталь: | MOUNT OPERATION |
Парткод: | 302R605030 |
Деталь: | KEY 10 |
Парткод: | 302R605060 |
Деталь: | KEY LEFT |
Парткод: | 302R605070 |
Деталь: | LID HINGE |
Парткод: | 302R605090 |
Деталь: | KEY HOME |
Парткод: | 302R605100 |
Деталь: | KEY COLOR |
Парткод: | 302R605110 |
Деталь: | FILM FFC LCD |
Парткод: | 302R605120 |
Деталь: | LABEL COLOR |
Парткод: | 302R605130 |
Деталь: | FILM OPERATION |
Парткод: | 302R605150 |
Деталь: | KEY STOP |
Парткод: | 3V2NM05100 |
Деталь: | KEY RESET |
Парткод: | 3V2NM05110 |
Деталь: | CUSHION LCD A |
Парткод: | 3V2NM05250 |
Деталь: | CUSHION LCD B |
Парткод: | 3V2NM05260 |
Деталь: | LENS LED |
Парткод: | 3V2NM05300 |
Деталь: | CUSHION LCD C |
Парткод: | 3V2NM05360 |
Деталь: | SHIELD LCD |
Парткод: | 3V2NM05370 |
Деталь: | PLATE EARTH LCD FRONT |
Парткод: | 3V2R605140 |
Деталь: | FERRITE CORE |
Парткод: | 7YBFP007C001H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610003++H01 |
Деталь: | WIRE FFC PANEL MAIN-KEY |
Парткод: | 302R646230 |
Деталь: | WIRE LCD POWER |
Парткод: | 302R646250 |
Деталь: | WIRE FFC LCD |
Парткод: | 302R646300 |
Деталь: | COVER PANEL |
Парткод: | 302R605040 |
Деталь: | LID PANEL |
Парткод: | 302R605050 |
Деталь: | HOLDER FULCRUM OPERATION |
Парткод: | 302R405100 |
Деталь: | LID OPERATION REAR |
Парткод: | 302R605080 |
Деталь: | SHEET OPERATION JP |
Парткод: | 302R605500 |
Деталь: | SHEET OPERATION KDA EN |
Парткод: | 302R605520 |
Деталь: | SHEET OPERATION EN |
Парткод: | 302R605510 |
Деталь: | PARTS OPERATION UNIT H SP |
Парткод: | 302R694030 |
Деталь: | DP ASSY SP |
Парткод: | 302R493010 |
Деталь: | GEAR Z22L TC ROLL B |
Парткод: | 302R422090 |
Деталь: | SPRING SEP EARTH B |
Парткод: | 302HN22080 |
Деталь: | TAPE BRUSH |
Парткод: | 302HN22100 |
Деталь: | PARTS ROLLER TRANSFER SP |
Парткод: | 302NR94060 |
Деталь: | BRUSH DISCHARGER |
Парткод: | 302NR22030 |
Деталь: | HOLDER BRUSH |
Парткод: | 302NR22101 |
Деталь: | BUSH TRANS REAR |
Парткод: | 302R422010 |
Деталь: | LEVER TRANS RELEASE F |
Парткод: | 302R422020 |
Деталь: | LEVER TRANS RELEASE R |
Парткод: | 302R422030 |
Деталь: | GUIDE PAPER CHUTE A |
Парткод: | 302R422100 |
Деталь: | SHEET PAPER CHUTE |
Парткод: | 302R422060 |
Деталь: | BUSH TRANS F |
Парткод: | 302R422070 |
Деталь: | LABEL CONVEYING B |
Парткод: | 302R424170 |
Деталь: | HOOK DU RELEASE |
Парткод: | 302R429040 |
Деталь: | COVER RELEASE HOOK |
Парткод: | 302R429130 |
Деталь: | SPRING HOOK L |
Парткод: | 302KV29150 |
Деталь: | SPRING HOOK R |
Парткод: | 302KV29160 |
Деталь: | SPRING EARTH DU A |
Парткод: | 302R429070 |
Деталь: | STOPPER MPF FEED |
Парткод: | 302KV08180 |
Деталь: | SPRING CONVEYING STOPPER |
Парткод: | 302R429140 |
Деталь: | PARTS ROLLER DU L SP |
Парткод: | 302R494380 |
Деталь: | PARTS ROLLER DU SP |
Парткод: | 302R494410 |
Деталь: | BUSH SPIRAL |
Парткод: | 302K312340 |
Деталь: | STOPPER 3/2BT1107 A4 |
Парткод: | 5MVX111DN007 |
Деталь: | BUSH DU JOINT |
Парткод: | 302R429120 |
Деталь: | GEAR Z21L DU |
Парткод: | 302R429020 |
Деталь: | SPRING EARTH DU B |
Парткод: | 302R429080 |
Деталь: | BUSH ROLLER EARTH |
Парткод: | 302KV29190 |
Деталь: | SPRING EARTH DU ROLL |
Парткод: | 302R429060 |
Деталь: | PULLEY P24-S2M |
Парткод: | 302KV29200 |
Деталь: | PULLEY P24 DU |
Парткод: | 302NR29040 |
Деталь: | BELT S2M Z256 |
Парткод: | 302R429050 |
Деталь: | COVER HARNESS B |
Парткод: | 302R429110 |
Деталь: | COVER BELT DU |
Парткод: | 302R429150 |
Деталь: | SHAFT RIGHT COVER F |
Парткод: | 302K304550 |
Деталь: | FILM CONVEYING SHAFT |
Парткод: | 302K304630 |
Деталь: | SHAFT RIGHT COVER R |
Парткод: | 302K304560 |
Деталь: | STRAP RIGHT COVER |
Парткод: | 302R429090 |
Деталь: | GUIDE BANNER |
Парткод: | 302R408120 |
Деталь: | STRAP LINK MPF |
Парткод: | 302R408230 |
Деталь: | STOPPER STRAP |
Парткод: | 302K308470 |
Деталь: | COVER RIGHT |
Парткод: | 302R429010 |
Деталь: | LABEL CONVEYING CAUTION |
Парткод: | 302R434190 |
Деталь: | PARTS 2ND TRANS ASSY SP |
Парткод: | 302R494070 |
Деталь: | TABLE MAIN |
Парткод: | 3V2R418010 |
Деталь: | CURSOR FRONT |
Парткод: | 3V2NM18460 |
Деталь: | CURSOR REAR |
Парткод: | 3V2NM18470 |
Деталь: | COVER CURSOR |
Парткод: | 3V2R418020 |
Деталь: | GEAR CASSETTE/A-49 CASSETTE A4 |
Парткод: | 5MVG127DN071 |
Деталь: | LABEL FACE UP |
Парткод: | 303R334020 |
Деталь: | PARTS TABLE MAIN ASSY SP |
Парткод: | 302R494110 |
Деталь: | PARTS MOTOR-BL ASSY D SP |
Парткод: | 302R494460 |
Деталь: | PARTS MOTOR-BL ASSY C SP |
Парткод: | 302R494450 |
Деталь: | PARTS MOTOR-BL ASSY B SP |
Парткод: | 302R494440 |
Деталь: | PLATE DRUM EARTH |
Парткод: | 302R412150 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | GEAR Z44L-Z33L |
Парткод: | 302R431430 |
Деталь: | GEAR Z63R-Z24R |
Парткод: | 302NR31240 |
Деталь: | GEAR Z35R |
Парткод: | 302R431420 |
Деталь: | HOLDER CONT DRIVE R |
Парткод: | 302R431620 |
Деталь: | PARTS SENSOR OPT. SP |
Парткод: | 302P794010 |
Деталь: | SPRING JOINT |
Парткод: | 302NR02290 |
Деталь: | GEAR JOINT Z38S |
Парткод: | 302R431640 |
Деталь: | GEAR Z50S |
Парткод: | 302R431660 |
Деталь: | GEAR Z25S-Z50L |
Парткод: | 302R431650 |
Деталь: | PARTS DC MOTOR ASSY B SP |
Парткод: | 302R494200 |
Деталь: | PLATE MOTOR DC |
Парткод: | 302R431630 |
Деталь: | HOLDER CONT DRIVE F |
Парткод: | 302R431610 |
Деталь: | DR-5195 |
Парткод: | 302R493040 |
Деталь: | DR-5205 |
Парткод: | 302R693010 |
Деталь: | PARTS MOTOR-BL ASSY E SP |
Парткод: | 302R494470 |
Деталь: | GEAR Z25L-Z18P |
Парткод: | 302R431530 |
Деталь: | GEAR Z16S-Z25P |
Парткод: | 302R431540 |
Деталь: | BELT S2M 244 |
Парткод: | 302R431570 |
Деталь: | BRACKET TERMINAL |
Парткод: | 302R439310 |
Деталь: | SPRING HV MAIN |
Парткод: | 302R439320 |
Деталь: | SPRING HV MAG |
Парткод: | 302R439330 |
Деталь: | SPRING HV SLEEVE |
Парткод: | 302R439340 |
Деталь: | LID TERMINAL |
Парткод: | 302R439380 |
Деталь: | SPRING DRUM PWB |
Парткод: | 302R439390 |
Деталь: | PARTS PWB DRUM DLP CONNECT ASSY SP |
Парткод: | 302R694040 |
Деталь: | SPRING DLP PWB |
Парткод: | 302R439400 |
Деталь: | RAIL MIDDLE TRANSFER R |
Парткод: | 302R402510 |
Деталь: | PIN CLN DRIVE A |
Парткод: | 302R431730 |
Деталь: | PIN CLN DRIVE B |
Парткод: | 302R431740 |
Деталь: | SPRING HOOK RAIL TRANSFER |
Парткод: | 302R402650 |
Деталь: | SPRING CONTACT 2T |
Парткод: | 302R439560 |
Деталь: | SPRING TRANS K |
Парткод: | 302R439410 |
Деталь: | SPRING TRANS M |
Парткод: | 302R439420 |
Деталь: | SPRING TRANS C |
Парткод: | 302R439430 |
Деталь: | SPRING TRANS Y |
Парткод: | 302R439440 |
Деталь: | SPRING TRANS ARM |
Парткод: | 302R439450 |
Деталь: | SPRING TRANS LEFT |
Парткод: | 302R439460 |
Деталь: | SHAFT CLN DRIVE |
Парткод: | 302R431510 |
Деталь: | GEAR Z15L |
Парткод: | 302R431860 |
Деталь: | BUSH 6 |
Парткод: | 302K324450 |
Деталь: | GEAR Z17R MIDDLE |
Парткод: | 303K831070 |
Деталь: | GEAR Z19L-Z14R TONNER SUPPLY |
Парткод: | 302HN21200 |
Деталь: | BRACKET TENSION PULLEY |
Парткод: | 302R431580 |
Деталь: | SPRING MAIN DRIVE A |
Парткод: | 302K031410 |
Деталь: | SHEET TENSION |
Парткод: | 302R431600 |
Деталь: | GEAR Z27L-Z21P |
Парткод: | 302R431750 |
Деталь: | BELT S2M 800 |
Парткод: | 302R431560 |
Деталь: | GEAR Z27R-Z21R |
Парткод: | 302R431520 |
Деталь: | PULLEY Z21P S2M |
Парткод: | 302R431550 |
Деталь: | PLLLEY TENSION |
Парткод: | 302R431590 |
Деталь: | PARTS TONER SUPPLY ASSY SP |
Парткод: | 302R494140 |
Деталь: | PARTS BRACKET TERMINAL ASSY SP |
Парткод: | 302R494040 |
Деталь: | Ролик отделения бумаги в держателе, в сборе |
Парткод: | CET4322 |
Цена: | 450 ₽ |
Деталь: | Резина ролика отделения бумаги |
Парткод: | CET4322PT |
Цена: | 110 ₽ |
Деталь: | Резина ролика захвата бумаги |
Парткод: | CET7806BPT |
Цена: | 110 ₽ |
Деталь: | Резина ролика подачи бумаги |
Парткод: | CET7829 |
Цена: | 150 ₽ |
Деталь: | CAP SPRING/B-11 ENCLOSURE A4 |
Парткод: | 2FM04150 |
Деталь: | SPRING TC L |
Парткод: | 302HG24150 |
Деталь: | BUSH REG R |
Парткод: | 302HN24110 |
Деталь: | STOPPER BUSH REG |
Парткод: | 302HN24150 |
Деталь: | SPRING SEP EARTH A |
Парткод: | 302HN24270 |
Деталь: | SPRING DU |
Парткод: | 302HN24290 |
Деталь: | STOPPER TC SPRING |
Парткод: | 302NT22010 |
Деталь: | PULLEY PA |
Парткод: | 302HN24400 |
Деталь: | CUT WASHER 5 |
Парткод: | 302KK04570 |
Деталь: | SHEET REGIST C |
Парткод: | 302KV06260 |
Деталь: | SHEET REGIST CR |
Парткод: | 302KV06410 |
Деталь: | GEAR Z31R |
Парткод: | 302KV24110 |
Деталь: | PARTS ROLLER REGIST RUBBER SP |
Парткод: | 302R494400 |
Деталь: | SPRING EARTH REGIST RUBBER |
Парткод: | 302NR24110 |
Деталь: | BUSH REGIST EW |
Парткод: | 302NR24120 |
Деталь: | SPRING REGIST L |
Парткод: | 302NR24140 |
Деталь: | SPRING REGIST R |
Парткод: | 302NR24150 |
Деталь: | SPRING BRUSH EARTH |
Парткод: | 302R422040 |
Деталь: | SPRING PAPER CHUTE |
Парткод: | 302R422080 |
Деталь: | GUIDE FEED DU |
Парткод: | 302R424020 |
Деталь: | PULLEY MIDDLE |
Парткод: | 302R424030 |
Деталь: | ACTUATOR DU |
Парткод: | 302R424040 |
Деталь: | SPRING DU ACTUATOR |
Парткод: | 302R424080 |
Деталь: | SPRING GUIDE EARTH |
Парткод: | 302R424120 |
Деталь: | SPRING MIDDLE PULLEY |
Парткод: | 302R424130 |
Деталь: | SPRING EARTH CONVEYING |
Парткод: | 302R424140 |
Деталь: | LABEL CONVEYING A |
Парткод: | 302R424160 |
Деталь: | PLATE GUIDE CONVEYING |
Парткод: | 302R424210 |
Деталь: | COVER HARNESS A |
Парткод: | 302R429100 |
Деталь: | WIRE CONVEYING UNIT |
Парткод: | 302R646350 |
Деталь: | PARTS SENSOR OPT. SP |
Парткод: | 302P794010 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | SHEET PAPER GUIDE EARTH |
Парткод: | 302NT22030 |
Деталь: | PARTS CONVEYING ASSY SP |
Парткод: | 302R494060 |
Деталь: | MOUNT INTERLOCK SW B |
Парткод: | 302R402770 |
Деталь: | INTER LOCK SWITCH |
Парткод: | 2FB27160 |
Деталь: | HOLDER DRAWER |
Парткод: | 302R402260 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610008++H01 |
Деталь: | PLATE EARTH DF |
Парткод: | 302R402290 |
Деталь: | HOLDER WIRE A |
Парткод: | 303LL02180 |
Деталь: | MOUNT HEATER PWB |
Парткод: | 302R439160 |
Деталь: | SPRING TRANS FAN |
Парткод: | 302R439660 |
Деталь: | PARTS PWB HEATER RELAY ASSY SP |
Парткод: | 302R694050 |
Деталь: | PLATE MAIN LEFT |
Парткод: | 302R439020 |
Деталь: | PLATE MAIN LOW |
Парткод: | 302R439030 |
Деталь: | DUCT FUSER MOTOR A |
Парткод: | 302R433160 |
Деталь: | DUCT FUSER MOTOR B |
Парткод: | 302R433170 |
Деталь: | MOUNT ENGINE |
Парткод: | 302R439080 |
Деталь: | SHIELD SCREW |
Парткод: | 302K903620 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | LK-5195 |
Парткод: | 302R493150 |
Деталь: | MEA UNIT-DEV Y |
Парткод: | DV-5205C |
Деталь: | MEA UNIT-DEV Y |
Парткод: | DV-5205K |
Деталь: | MEA UNIT-DEV Y |
Парткод: | DV-5205M |
Деталь: | MEA UNIT-DEV Y |
Парткод: | DV-5205Y |
Деталь: | PARTS UNIT LOW VOLTAGE 100 SP |
Парткод: | 302R694170 |
Деталь: | PARTS UNIT LOW VOLTAGE 200 SP |
Парткод: | 302R694180 |
Деталь: | SHEET LVU H |
Парткод: | 302R639030 |
Деталь: | MOUNT MAIN |
Парткод: | 302R639010 |
Деталь: | PARTS PWB MAIN ASSY SP |
Парткод: | 302R694090 |
Деталь: | PARTS PWB MAIN ASSY EU SP |
Парткод: | 302R694100 |
Деталь: | FAN BOX COOLING |
Парткод: | 302FZ44040 |
Деталь: | HOLDER FAN MAIN |
Парткод: | 302R439150 |
Деталь: | PARTS PWB ENGINE ASSY SP |
Парткод: | 302R694080 |
Деталь: | MOUNT SPRING HV 40 |
Парткод: | 302R639310 |
Деталь: | SPRING HV SLEEVE R |
Парткод: | 302R439590 |
Деталь: | SPRING HV MAG R |
Парткод: | 302R439600 |
Деталь: | SPRING HV MAIN R |
Парткод: | 302R439610 |
Деталь: | SPRING TRANS 2T |
Парткод: | 302R439480 |
Деталь: | SPRING TCL |
Парткод: | 302R439680 |
Деталь: | SPRING MID TRANS |
Парткод: | 302R439580 |
Деталь: | LID SPRING HV |
Парткод: | 302R439670 |
Деталь: | SPRING TRANS 40 |
Парткод: | 302R639320 |
Деталь: | PARTS UNIT HIGH VOLTAGE TRANSFER SP |
Парткод: | 302R694160 |
Деталь: | SPRING EARTH TC |
Парткод: | 302R639330 |
Деталь: | BRACKET HVU2 |
Парткод: | 302R439470 |
Деталь: | PARTS FAN COOLING LSU 60 SP |
Парткод: | 302LC94380 |
Деталь: | SPRING HV PT PB |
Парткод: | 302R439500 |
Деталь: | SPRING HV PT CLN |
Парткод: | 302R439490 |
Деталь: | SPRING HV BK 1T |
Парткод: | 302R439510 |
Деталь: | SPRING HV M 1T |
Парткод: | 302R439520 |
Деталь: | SPRING HV C 1T |
Парткод: | 302R439530 |
Деталь: | SPRING HV Y 1T |
Парткод: | 302R439540 |
Деталь: | ACCESS.CLAMP |
Парткод: | 7YZM390011++H01 |
Деталь: | ACCESS.SPACER |
Парткод: | 7YZM590001++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610002++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | LID WIRE GUIDE |
Парткод: | 302H039270 |
Деталь: | PARTS MEMORY MODULE SP |
Парткод: | 302LH94230 |
Деталь: | TR-5195 |
Парткод: | 302R493020 |
Деталь: | Вал переноса заряда, в сборе |
Парткод: | 302NR94061 |
Цена: | 4 400 ₽ |
Деталь: | GEAR Z36L-Z20S |
Парткод: | 302HN31030 |
Деталь: | PARTS DC MOTOR ASSY C SP |
Парткод: | 302R494290 |
Деталь: | HOUSING DRIVE |
Парткод: | 302R409500 |
Деталь: | LID HOUSING DRIVE |
Парткод: | 302R409510 |
Деталь: | GEAR Z57S |
Парткод: | 302R409520 |
Деталь: | JOINT LIFT |
Парткод: | 302R409530 |
Деталь: | GEAR Z34S-Z16S |
Парткод: | 302R409540 |
Деталь: | SPRING JOINT LIFT |
Парткод: | 302R409550 |
Деталь: | GEAR Z41S Z14S |
Парткод: | 303K831280 |
Деталь: | HOLDER PAPER SENSOR |
Парткод: | 302R409360 |
Деталь: | PARTS SENSOR OPT. SP |
Парткод: | 302P794010 |
Деталь: | SW.PUSH |
Парткод: | 7SP01000004+H01 |
Деталь: | WIRE CASSETTE SWITCH |
Парткод: | 302R646370 |
Деталь: | PARTS FAN COOLING LSU 60 SP |
Парткод: | 302LC94380 |
Деталь: | DUCT BASE REAR |
Парткод: | 302R433120 |
Деталь: | DUCT BASE FRONT |
Парткод: | 302R433130 |
Деталь: | HOLDER PWB |
Парткод: | 302R439170 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | ACCESS.SADDLE |
Парткод: | 7YZM610007++H01 |
Деталь: | ACCESS.SPACER |
Парткод: | 7YZM510018++H01 |
Деталь: | DUCT DLP REAR A |
Парткод: | 302R433010 |
Деталь: | DUCT DLP REAR B |
Парткод: | 302R433020 |
Деталь: | GUIDE WIRE INLET |
Парткод: | 302R439120 |
Деталь: | LID WIRE GUIDE |
Парткод: | 302H039270 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610002++H01 |
Деталь: | MOUNT INLET A |
Парткод: | 302R439050 |
Деталь: | GUIDE WIRE LVU |
Парткод: | 302R439130 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610001++H01 |
Деталь: | CAP DECK PIN |
Парткод: | 302R439140 |
Деталь: | SEAL CASE D DLP |
Парткод: | 302FZ14970 |
Деталь: | SHIELD SCREW |
Парткод: | 302H002380 |
Деталь: | PARTS LIFT MOTOR ASSY SP |
Парткод: | 302R494220 |
Деталь: | PARTS PAPER SENSOR ASSY SP |
Парткод: | 302R494130 |
Деталь: | FK-5197 |
Парткод: | 302R493130 |
Деталь: | FK-5195 |
Парткод: | 302R493110 |
Деталь: | FK-5206 |
Парткод: | 302R693090 |
Деталь: | FK-5207 |
Парткод: | 302R693100 |
Деталь: | FK-5205 |
Парткод: | 302R693080 |
Деталь: | COVER WIRE FUSER |
Парткод: | 302R402750 |
Деталь: | PARTS UNIT LOW VOLTAGE 100 SP |
Парткод: | 302R694170 |
Деталь: | PARTS UNIT LOW VOLTAGE 200 SP |
Парткод: | 302R694180 |
Деталь: | SHEET LVU H |
Парткод: | 302R639030 |
Деталь: | MOUNT MAIN |
Парткод: | 302R639010 |
Деталь: | PARTS PWB MAIN ASSY SP |
Парткод: | 302R594020 |
Деталь: | PARTS PWB MAIN ASSY EU SP |
Парткод: | 302R594030 |
Деталь: | PARTS PWB MAIN ASSY SP |
Парткод: | 302R694090 |
Деталь: | FAN BOX COOLING |
Парткод: | 302FZ44040 |
Деталь: | HOLDER FAN MAIN |
Парткод: | 302R439150 |
Деталь: | PARTS PWB ENGINE ASSY SP |
Парткод: | 302R594010 |
Деталь: | MOUNT SPRING HV |
Парткод: | 302R439550 |
Деталь: | SPRING HV SLEEVE R |
Парткод: | 302R439590 |
Деталь: | SPRING HV MAG R |
Парткод: | 302R439600 |
Деталь: | SPRING HV MAIN R |
Парткод: | 302R439610 |
Деталь: | SPRING TRANS 2T |
Парткод: | 302R439480 |
Деталь: | SPRING TCL |
Парткод: | 302R439680 |
Деталь: | SPRING MID TRANS |
Парткод: | 302R439580 |
Деталь: | LID SPRING HV |
Парткод: | 302R439670 |
Деталь: | SPRING HV SLEEVE R4 |
Парткод: | 302R439620 |
Деталь: | SPRING HV MAG R4 |
Парткод: | 302R439630 |
Деталь: | SPRING HV MAIN R4 |
Парткод: | 302R439640 |
Деталь: | BRACKET HVU2 |
Парткод: | 302R439470 |
Деталь: | PARTS FAN COOLING LSU 60 SP |
Парткод: | 302LC94380 |
Деталь: | SPRING HV PT PB |
Парткод: | 302R439500 |
Деталь: | SPRING HV PT CLN |
Парткод: | 302R439490 |
Деталь: | SPRING HV BK 1T |
Парткод: | 302R439510 |
Деталь: | SPRING HV M 1T |
Парткод: | 302R439520 |
Деталь: | SPRING HV C 1T |
Парткод: | 302R439530 |
Деталь: | SPRING HV Y 1T |
Парткод: | 302R439540 |
Деталь: | ACCESS.CLAMP |
Парткод: | 7YZM390011++H01 |
Деталь: | ACCESS.SPACER |
Парткод: | 7YZM590001++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610002++H01 |
Деталь: | ACCESS SADDLE |
Парткод: | 7YZM610004++H01 |
Деталь: | LID WIRE GUIDE |
Парткод: | 302H039270 |
Деталь: | PARTS MEMORY MODULE SP |
Парткод: | 302LH94230 |
Деталь: | PARTS SSD SP |
Парткод: | 302R594050 |
Деталь: | SPRING BYPASS TEBLE |
Парткод: | 302FB17700 |
Деталь: | TABLE MPF A |
Парткод: | 302R408060 |
Деталь: | TABLE MPF B |
Парткод: | 302R408070 |
Деталь: | TABLE MPF D |
Парткод: | 302R408090 |
Деталь: | CURSOR MPF FRONT |
Парткод: | 302R408100 |
Деталь: | CURSOR MPF REAR |
Парткод: | 302R408110 |
Деталь: | STOPPER GEAR |
Парткод: | 302R408150 |
Деталь: | SPRING CURSOR |
Парткод: | 302R408160 |
Деталь: | STOPPER MULTI |
Парткод: | 302R408170 |
Деталь: | STOPPER BYPASS TABLE |
Парткод: | 302R408220 |
Деталь: | LABEL MPF CAUTION |
Парткод: | 302R434010 |
Деталь: | GEAR 20,PAPER FEED DRIVE |
Парткод: | 35322020 |
Деталь: | TABLE MPF C |
Парткод: | 302R408080 |
Деталь: | TABLE MPF C |
Парткод: | 302R608010 |
Деталь: | SPONGE WIRE MPT |
Парткод: | 302H708150 |
Деталь: | GUIDE WIRE TRAY |
Парткод: | 302K908160 |
Деталь: | ACTUATOR SIZE DETECTION |
Парткод: | 302K908211 |
Деталь: | SPRING-TORSION SIZE DETECTION |
Парткод: | 302K908220 |
Деталь: | GEAR Z36S |
Парткод: | 302R408180 |
Деталь: | PARTS PWB PAPER SIZE SENSOR ASSY SP |
Парткод: | 303R394050 |
Деталь: | PARTS SENSOR OPT. SP |
Парткод: | 302P794010 |
Деталь: | SW.PUSH |
Парткод: | 7SP01000004+H01 |
Деталь: | WIRE MPF TABLE |
Парткод: | 302R646240 |
Деталь: | FILM MPF TABLE |
Парткод: | 302R608020 |
Деталь: | PARTS MPF TABLE ASSY L SP |
Парткод: | 302R494090 |
Деталь: | PARTS MPF TABLE ASSY H SP |
Парткод: | 302R694020 |
Деталь: | BASE DP |
Парткод: | 303R302010 |
Деталь: | STOPPER BASE |
Парткод: | 303R402020 |
Деталь: | SPRING-COMPRESSION EXIT |
Парткод: | 3V2NM18990 |
Деталь: | SHAFT EJECT PULLEY |
Парткод: | 302F928290 |
Деталь: | PULLEY EJECT |
Парткод: | 3HK10030 |
Деталь: | SPONGE EJECT |
Парткод: | 3HK10060 |
Деталь: | SPONGE ORIGINAL MAT FILM |
Парткод: | 303PH02030 |
Деталь: | CUSHION ORIGINAL MAT B |
Парткод: | 303MX02031 |
Деталь: | Hinge Left |
Парткод: | 303R302020 |
Деталь: | Hinge Right |
Парткод: | 303R302030 |
Деталь: | PLATE HINGE |
Парткод: | 303R302050 |
Деталь: | SPRING FEED |
Парткод: | 302HN31410 |
Деталь: | BUSH DRIVE |
Парткод: | 302HN31590 |
Деталь: | SPRING INPUT MPF |
Парткод: | 302HN31650 |
Цена: | 150 ₽ |
Деталь: | JOINT SHAFT CASSETTE |
Парткод: | 302HN31660 |
Деталь: | SOLENOID MPF |
Парткод: | 302HN44160 |
Деталь: | GEAR Z28S |
Парткод: | 302K331170 |
Деталь: | GEAR Z45S INPUT MPF A |
Парткод: | 302K331180 |
Деталь: | GEAR Z45S INPUT MPF B |
Парткод: | 302K331190 |
Деталь: | BUSH DRIVE 8 |
Парткод: | 302K331230 |
Деталь: | GEAR Z35R |
Парткод: | 302K931510 |
Деталь: | PARTS MOTOR-BL ASSY F SP |
Парткод: | 302R494480 |
Деталь: | BUSH DRIVE POM |
Парткод: | 302LV31480 |
Деталь: | GEAR Z72R-Z28L |
Парткод: | 302NR31020 |
Деталь: | GEAR Z72R-Z40L |
Парткод: | 302NR31030 |
Деталь: | GEAR Z24L |
Парткод: | 302NR31060 |
Деталь: | GEAR Z26L |
Парткод: | 302NR31070 |
Деталь: | GEAR Z25R OUTPUT CL |
Парткод: | 302NR31090 |
Деталь: | GEAR Z32L OUTPUT CL |
Парткод: | 302NR31100 |
Деталь: | SHAFT CLUTCH FEED |
Парткод: | 302NR31110 |
Деталь: | PIN DRIVE D |
Парткод: | 302NR31340 |
Деталь: | SHEET FEED DRIVE A |
Парткод: | 302NR31680 |
Деталь: | PARTS CLUTCH 35 Z35R SP |
Парткод: | 302NR94010 |
Деталь: | CAM MPF |
Парткод: | 302R408190 |
Деталь: | HOLDER FEED DRIVE R |
Парткод: | 302R431210 |
Деталь: | HOLDER FEED DRIVE F |
Парткод: | 302R431220 |
Деталь: | GEAR Z31L |
Парткод: | 302R431280 |
Деталь: | GEAR Z48R-Z22S |
Парткод: | 302R431310 |
Деталь: | SHAFT CLUTCH DLP |
Парткод: | 302R431350 |
Деталь: | WIRE CL |
Парткод: | 302R646430 |
Деталь: | CONNECTOR 292254-2 |
Парткод: | 7YCC02B1003+H01 |
Деталь: | GEAR Z24R |
Парткод: | 302R431330 |
Деталь: | GEAR Z27R |
Парткод: | 302R431270 |
Деталь: | BUSH SCREW |
Парткод: | 302H702590 |
Деталь: | SHAFT JOINT REG |
Парткод: | 302R431240 |
Деталь: | RING STOPPER/A-49 FEED A4 |
Парткод: | 5MVX111DN003 |
Деталь: | GEAR Z22R |
Парткод: | 302R431300 |
Деталь: | GUIDE FEED DRIVE |
Парткод: | 302R431230 |
Деталь: | SHAFT JOINT MID |
Парткод: | 302R431250 |
Деталь: | GEAR Z25R |
Парткод: | 302R431320 |
Деталь: | ONE-WAY CLUTCH 6 |
Парткод: | 302R424270 |
Деталь: | PARTS FEED DRIVE ASSY SP |
Парткод: | 302R494080 |
Деталь: | COVER TRAY REAR |
Парткод: | 302R404160 |
Деталь: | LID TRAY REAR |
Парткод: | 302R404170 |
Деталь: | COVER EXIT LEFT |
Парткод: | 302R404190 |
Деталь: | COVER EXIT |
Парткод: | 302R428010 |
Деталь: | COVER TRAY |
Парткод: | 302R404140 |
Деталь: | MOUNT DF FRONT |
Парткод: | 302R402280 |
Деталь: | COVER RIGHT LOWER |
Парткод: | 302R404080 |
Деталь: | Cover Right Rear |
Парткод: | 302R404070 |
Деталь: | COVER RIGHT TOP |
Парткод: | 302R404050 |
Деталь: | LID RIGHT TOP |
Парткод: | 302R404180 |
Деталь: | SPONGE RIGHT TOP |
Парткод: | 302R404220 |
Деталь: | COVER FRONT RIGHT |
Парткод: | 302R404060 |
Деталь: | COVER EXIT FRONT |
Парткод: | 302R404030 |
Деталь: | COVER FRONT |
Парткод: | 302R404010 |
Деталь: | COVER FRONT UPPER |
Парткод: | 302R404020 |
Деталь: | PLATE MAGNET |
Парткод: | 302NL04270 |
Деталь: | STRAP FRONT COVER |
Парткод: | 302R404200 |
Деталь: | COVER EXIT TOP |
Парткод: | 302R404040 |
Деталь: | COVER LEFT CONTROLLER |
Парткод: | 302R404130 |
Деталь: | COVER LEFT CONTROLLER |
Парткод: | 302R604130 |
Деталь: | COVER LEFT LOWER |
Парткод: | 302R404120 |
Деталь: | COVER REAR LOWER |
Парткод: | 302R404110 |
Деталь: | COVER REAR RIGHT |
Парткод: | 302R404090 |
Деталь: | COVER REAR LEFT |
Парткод: | 302R404100 |
Деталь: | LID MAIN |
Парткод: | 302R439040 |
Деталь: | LABEL EMBLEM 306C |
Парткод: | 302R434090 |
Деталь: | LABEL EMBLEM 356C |
Парткод: | 302R534010 |
Деталь: | LABEL EMBLEM 406C |
Парткод: | 302R634010 |
Деталь: | EMBLEM |
Парткод: | 303R304050 |
Деталь: | PLATE OPTION |
Парткод: | 302K339050 |
Деталь: | COVER ISU REAR |
Парткод: | 302R417180 |
Деталь: | PLATE EARTH COVER TRAY |
Парткод: | 302R402320 |
Деталь: | SHEET COVER FRONT L |
Парткод: | 302R434200 |
Деталь: | SHEET COVER FRONT H |
Парткод: | 302R634020 |
Деталь: | SHEET CORE |
Парткод: | 302R439220 |
Деталь: | SHEET COVER LEFT CONT |
Парткод: | 302R604140 |
Деталь: | COVER INNER |
Парткод: | 302R403530 |
Деталь: | COVER INNER |
Парткод: | 302R603530 |
Деталь: | SW.PUSH |
Парткод: | 7SP01000004+H01 |
Деталь: | MAGNET CATCH |
Парткод: | 302H004660 |
Деталь: | HOLDER SPRING L |
Парткод: | 302R403570 |
Деталь: | SPRING HOOK L |
Парткод: | 302R403550 |
Деталь: | SPRING HOOK R |
Парткод: | 302R403540 |
Деталь: | GEAR EXIT JOINT Z26S |
Парткод: | 2BL21390 |
Деталь: | GEAR Z18S |
Парткод: | 302R403350 |
Деталь: | GEAR Z15L-Z18S |
Парткод: | 302R403330 |
Деталь: | PLATE DRIVE WTB |
Парткод: | 302R403320 |
Деталь: | PARTS,FAN IMAGE SP |
Парткод: | 302FZ94660 |
Деталь: | SEAL FAN MOTOR A |
Парткод: | 302R403630 |
Деталь: | FILM FRONT FAN |
Парткод: | 302R403660 |
Деталь: | PLATE FRONT FAN |
Парткод: | 302R403610 |
Деталь: | WIRE STOPPER |
Парткод: | 302K931080 |
Деталь: | DUCT FRONT |
Парткод: | 302R403620 |
Деталь: | HOLDER SENSOR |
Парткод: | 302R403520 |
Деталь: | SPACER LED |
Парткод: | 302K312400 |
Деталь: | PARTS PWB THERMISTOR ASSY SP |
Парткод: | 302R694190 |
Деталь: | HOLDER SWITCH |
Парткод: | 302R403700 |
Деталь: | ACTUATOR SWITCH |
Парткод: | 302R403710 |
Деталь: | SPONGE WIRE MPT |
Парткод: | 302H708150 |
Деталь: | LABEL BLACK |
Парткод: | 302K034090 |
Деталь: | LABEL MAGENTA |
Парткод: | 302K034100 |
Деталь: | LABEL CYAN |
Парткод: | 302K034110 |
Деталь: | LABEL YELLOW |
Парткод: | 302K034120 |
Деталь: | FILM INNER COVER |
Парткод: | 302R403650 |
Деталь: | LEVER ID SENSOR |
Парткод: | 302R403590 |
Деталь: | PAD SEPARATION |
Парткод: | 302R408250 |
Деталь: | SEAL SEPARATION |
Парткод: | 302R408210 |
Деталь: | HOLDER SEPARATION |
Парткод: | 302K308041 |
Деталь: | SPRING SEPARATION |
Парткод: | 302R408240 |
Деталь: | CUSHION HOLDER F |
Парткод: | 302K308300 |
Деталь: | CUSHION HOLDER R |
Парткод: | 302K308310 |
Деталь: | MOUNT SEPARATION |
Парткод: | 302MV08040 |
Деталь: | ROLLER MPF |
Парткод: | 302K308150 |
Деталь: | SPRING MPF ROLL |
Парткод: | 302K308270 |
Деталь: | PIN FEED ROLL |
Парткод: | 302MV08020 |
Деталь: | PULLEY MPF |
Парткод: | 302MV08030 |
Деталь: | BASE MPF |
Парткод: | 302R408010 |
Деталь: | PARTS SENSOR OPT SP |
Парткод: | 302P794010 |
Деталь: | ACTUATOR MPF |
Парткод: | 302K308020 |
Деталь: | SPRING ACTUATOR |
Парткод: | 302K308250 |
Деталь: | SPRING LIFT F |
Парткод: | 302K308130 |
Деталь: | SPRING LIFT R |
Парткод: | 302K308120 |
Деталь: | PLATE LIFT |
Парткод: | 302R408040 |
Деталь: | PAD LIFT |
Парткод: | 302K308110 |
Деталь: | ARM LIFT |
Парткод: | 302K308140 |
Деталь: | SPRING EARTH |
Парткод: | 302R408130 |
Деталь: | GUIDE UPPER MPF |
Парткод: | 302R408020 |
Деталь: | STAY MPF UPPER |
Парткод: | 302R408030 |
Деталь: | BUSH 10 |
Парткод: | 302K308070 |
Деталь: | SHAFT MPF |
Парткод: | 302R408050 |
Деталь: | PARTS GEAR MPF Z28 SP |
Парткод: | 302K394320 |
Деталь: | COVER MPF WIRE |
Парткод: | 302R408140 |
Деталь: | PARTS HOLDER SEPARATION SP |
Парткод: | 302R494180 |
Деталь: | PARTS ROLLER MPF ASSY SP |
Парткод: | 302MV94020 |
Коды ошибок
0030
0070
0100
0120
0130
0140
0150
0160
0170
0180
0360
0620
0640
0650
0660
0670
0680
0800
0830
0840
0870
0920
0970
1010
1020
1030
1040
1800
1810
1900
1910
2101
2102
2112
2201
2202
2211
2212
2500
2600
2610
2700
2760
2820
3100
3200
3210
3300
3310
3500
3800
4001
4011
4102
4103
4104
4201
4600
4700
5101
5102
5103
5104
6000
6020
6030
6040
6050
6200
6220
6230
6250
6400
6610
6910
7001
7002
7003
7004
7101
7102
7103
7104
7200
7210
7221
7231
7401
7402
7403
7404
7411
7412
7413
7414
7601
7602
7611
7612
7613
7614
7620
7800
7810
7901
7902
7903
7904
7911
7912
7913
7914
8000
8010
8020
8030
8090
8100
8140
8150
8160
8170
8180
8190
8200
8210
8230
8250
8260
8410
8420
8430
8500
8510
8520
8800
8900
8990
9070
9180
9500
9510
9530, 9540, 9550
F000
F010
F020
F040
F050
F12X
F13X
F14X
F15X
F18X
F1DX
F21X, F22X, F23X
F24X
F25X
F26X ... F2AX
F2BX ... F32X
F33X
F34X
F35X
F37X
F38X
F39X
F3AX ... F41X
F42X ... F46X
F47X, F48X, F49X
F4AX, F4CX
F4DX, F4EX
F50X
F51XF ... 57X
F58X ... F5EX
F62X
F68X
F69X ... F6CX
Описание
Error code: | 0030 |
Description: | FAX control PWB system error Processing with the fax software was disabled due to a software problem. |
Causes: | Defective FAX control PWB. |
Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Reinstall the fax software. 3. Replace the FAX control PWB. |
Error code: | 0070 |
Description: | FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
Causes: | Defective FAX software. Defective FAX control PWB. |
Remedy: | FAX control PWB (The FAX PWB installed will not be the one designed for the machine.) 1. Install the FAX system designed for the model. 2. Reinstall the fax software. |
Error code: | 0100 |
Display: | MAINTENANCE CALL 0100 |
Description: | Backup memory device error |
Causes: | Defective flash memory. Defective main PWB. |
Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
Error code: | 0120 |
Description: | There is a problem with Thermistor for Pre-Heater. |
Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
Remedy: | Check Cable connection around Thermistor Thermistor replacement |
Error code: | 0130 |
Description: | There is a problem with Thermistor for Print Heater. |
Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
Remedy: | Check Cable connection around Thermistor Thermistor replacement |
Error code: | 0140 |
Description: | There is a problem with Thermistor for dryer. |
Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
Remedy: | Check Cable connection around Thermistor Thermistor replacement |
Error code: | 0150 |
Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
Error code: | 0160 |
Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
Error code: | 0170 |
Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
Error code: | 0180 |
Description: | Even though the machine carries out the regular movement, the output of Maintenance Liquid Pump Sensor does not reach the expected value. |
Causes: | Maintenance Liquid Pump Motor has a problem. Maintenance Liquid Pump Sensor has a problem. Maintenance Liquid Pump Magnet has dropped out. Wiring or Flexible Cable has short circuitted |
Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Maintenance Liquid Pump Motor replacement Maintenance Liquid Pump Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
Error code: | 0360 |
Description: | Communication error between the engine ASIC During the readback data checked after data transmission, the checksum error or the video signal is not inverted. (failed 10 consecutive times) |
Causes: | Defective connector cable or poor contact in the connector. Engine relay PWB Main/Engine PWB |
Remedy: | Engine PWB: 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Check that the connectors on the engine PWB are properly connected, and if not, re-connect them. 3. Replace the engine PWB. |
Error code: | 0620 |
Description: | FAX image DIMM error 1. The Fax image DIMM has not been installed. 2. Fax image DIMM access error. |
Causes: | DIMM installed incorrectly. Defective main PWB. |
Remedy: | FAX image DIMM 1. Install the FAX image DIMM supplied in the FAX system onto the main PWB. 2. Firmly install the FAX image DIMM again onto the main board. 3. Check the FAX image DIMM terminals and remove any foreign objects that may be adhered to it. 4. Replace with a new FAX image DIMM. Main PWB. Replace the main PWB. |
Error code: | 0640 |
Description: | Hard disk error The hard disk cannot be accessed. |
Causes: | Defective hard disk. Defective main PWB. |
Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Lack of HDD capacity 1. Confirm the total capacity of the HDD if it is more than 320GB. Change the HDD or add it in case of lacking in capacity. Main PWB Replace the main PWB. |
Error code: | 0650 |
Display: | Scanner home failure CODE (0650) Turn power off, on |
Description: | Scanner Home Failure • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the Polygon Motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the Polygon Motor remains energized. |
Causes: | • Engine Control Board, PL13.0.20 • Image Processor Board, PL2.0.4 |
Remedy: | 1 Check connector P/J2 on the Image Processor Board. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Replace the Scanner. Does the problem persist? Go to step 3. Complete. 3 Replace the Engine Control Board. Does the problem persist? Go to step 4. Complete. 4 Replace the Power Supply. Complete. |
Error code: | 0660 |
Description: | Hard disk encryption key error |
Causes: | EEPROM. HDD. Main PWB |
Remedy: | EEPROM 1. Execute U004 if this occurs after the EEPROM has been changed. HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
Error code: | 0670 |
Description: | Hard disk overwriting erasure error |
Causes: | HDD. Main PWB. |
Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
Error code: | 0680 |
Description: | SSD error In case of inability of communication with the SSD. (for 35 ppm model only) |
Causes: | SSD, Main PWB |
Remedy: | SSD: 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Unplug the power cord from the wall outlet, and reinstall the SSD. 3. Check the connection failure between the KUIO connector of the main PWB and SSD, and reconnect it. 4. Initialize the SSD. |
Error code: | 0800 |
Display: | Print Unable 08 Turn the power off and then back on again. |
Description: | Image processing error JAM010X is detected twice. |
Causes: | Defective main PWB. |
Remedy: | Main PWB Replace the main PWB. |
Error code: | 0830 |
Description: | FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB |
Causes: | Defective FAX software. Defective FAX control PWB. |
Remedy: | FAX software 1. Reinstall the fax software. FAX control PWB 1. Execute initializing by U600.(Refer to the FAX service manual) 2. Replace the FAX control PWB. |
Error code: | 0840 |
Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
Causes: | The battery is disconnected from the main PWB Defective main PWB. |
Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
Error code: | 0870 |
Description: | PCFAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. |
Causes: | Improper installation FAX control PWB. Defective FAX control PWB or main PWB. |
Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Replace the FAX control PWB. HDD Execute U024 to initialize the HDD. Main PWB Replace the main PWB. |
Error code: | 0920 |
Description: | Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. |
Causes: | Defective FAX control PWB. |
Remedy: | FAX control PWB 1. Execute initializing by U600 (Refer to the FAX service manual). 2. Replace the FAX control PWB. |
Error code: | 0970 |
Description: | 12 V power down detect Power is disconnected during sleeping. |
Causes: | Defective power source PWB. |
Remedy: | Replace the power source PWB and check for correct operation. |
Error code: | 1010 |
Display: | Problem with Printhead L/R Chk printing results |
Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 1020 |
Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 1030 |
Display: | GARO W1221 |
Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
Error code: | 1040 |
Display: | GL2: W0501 The memory is full. |
Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
Error code: | 1800 |
Description: | Paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
Causes: | Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
Remedy: | Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 1810 |
Description: | Side multi tray communication error A communication error from side multi tray is detected 10 times in succession. |
Causes: | Improper installation side multi tray. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. |
Remedy: | Side multi tray Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). Engine PWB Check the engine software and upgrade to the latest, if necessary. Replace the engine PWB. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
Error code: | 1900 |
Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
Causes: | Defective PF main PWB. Device damage of EEPROM. |
Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
Error code: | 1910 |
Description: | Side multi tray EEPROM error When writing the data, read and write data does not match 3 times in succession. |
Causes: | Defective SM main PWB. Device damage of EEPROM. |
Remedy: | SM main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the SM main PWB (Refer to the service manual for the paper feeder). |
Error code: | 2101 |
Description: | Developer motor error After developer motor is driven, the ready signal does not turn to L within 2 s. After developer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor. Defective engine PWB. |
Remedy: | Developer unit 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor 1. To check the motor operation, execute DLP(K) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor and Feed PWB 1 (YC8) Feed PWB 1 (YC2) and Engine PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor. Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2102 |
Description: | Developer motor C error After developer motor C is driven, the ready signal does not turn to L within 5 s. After developer motor C is stabilized, the ready signal is at the H level for 5 s continuously. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor C. Defective engine PWB. |
Remedy: | Developer unit C 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor C 1. To check the motor operation, execute DLP(C) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor C and Motor control PWB (YC7) Motor control PWB (YC3) and Engine PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor C. Motor control PWB Replace the Motor control PWB Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2112 |
Description: | Developer motor startup error (M/C/Y) After the motor starts up, the ready signal is not turned ON for continuous 2 s |
Causes: | Defective connector cable or poor contact in the connector Defective drive transmission system. Defective motor. Defective PWB. |
Remedy: | Developer unit 1. Check that the developer roller can be rotated by hand, and if it is locked, replace the developer unit. Developer motor 1. Check if the couplings and gears rotate smoothly, and if necessary replace them. 2. Reconnect the connector if its connection is loose. 3. Check the continuity within the connector wire. If none, replace the wire. Developer motor - Engine PWB(YC16): 30 ppm model - Engine PWB(YC23): 35/40 ppm models 4. Replace the developer motor. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 2201 |
Description: | drum motor steady-state error After drum motor is stabilized, the ready signal is at the H level for 1 s continuously. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor. Defective engine PWB. |
Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. Drum motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2202 |
Description: | Drum motor C steady-state error The motor revolution fluctuates more than +/-6.2% of the normal revolution for 5s continuously, after the drum motor C has stabilized. The counter achieved by timer capture is less than 2200 in 10 times in a row. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor C. Defective engine PWB. |
Remedy: | Drum unit 1. Execute U030 Belt Meand (transfer Motor) and check that the drum motor can rotate. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the drum or the drum screw can rotate. 4. If it won’t rotate, replace the drum unit. Drum motor C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum motor C and Motor control PWB (YC4) Motor control PWB (YC3) and Engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum motor C. Motor control PWB Replace the Motor control PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2211 |
Description: | Drum motor startup error Drum motor is not stabilized within 2 s since the motor is activated. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor K. Defective engine PWB. |
Remedy: | Drum unit 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the drum or the drum screw can rotate. 3. If it won’t rotate, replace the drum unit. Drum motor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2212 |
Description: | Drum motor C startup error Drum motor C is not stabilized within 5 s since the motor is activated. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor C. Defective engine PWB. |
Remedy: | Drum unit 1. To check the motor operation, execute U030 Belt Mea nd (transfer motor).. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Decrease Vpp using U100. Change “set ac gain” of U100 from Auto to mode1. 4. Confirm that the drum or the drum screw can rotate. 5. If it won’t rotate, replace the drum unit. Drum motor C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum motor C and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum motor C. Motor control PWB Replace the Motor control PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2500 |
Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2600 |
Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
Error code: | 2610 |
Description: | PF paper feed motor error (paper feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 2PF - Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
Error code: | 2700 |
Description: | 3-color release motor error When the color release motor is driven, the color release sensor does not turn on/off for 5 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective color release motor. Defective engine PWB. |
Remedy: | Color release motor Color release sensor (Intermediate transfer belt unit) 1. To check the motor operation, execute U30 CMY Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Intermediate transfer belt unit and Engine PWB (YC3) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Intermediate transfer belt unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2760 |
Description: | Transfer motor startup error Transfer motor is not stabilized within 5 s since the motor is activated. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor Defective transfer motor. Defective engine PWB. |
Remedy: | Transfer motor 1. To check the motor operation, execute U030 Belt Meand. 2. Rotate the drive gear, the belt and the roller by the hand and check that they are not unusually loaded. 3. Clean the Intermediate transfer belt unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Transfer motor and Feed PWB 1 (YC13) Feed PWB 1(YC2) and Engine PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the Transfer motor. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 2820 |
Display: | Cannot adjust printhead. Press Online to clear the error and readjust printhead. |
Description: | Intermediate transfer belt motor steady-state error After transfer motor is stabilized, the ready signal is at the H level for 5 s continuously. The counter value obtained by timer capture is lower than 2200 for 10 times in a row. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective transfer motor. Defective engine PWB. |
Remedy: | Transfer motor 1. To check the motor operation, execute U030 Belt Meand. 2. Rotate the roller, driving gear by the hand and check that they are not unusually loaded. 3. Clean the intermediate transfer belt unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Transfer motor and Feed PWB 1(YC13) Feed PWB 1(YC2) and Engine PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the Transfer motor. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 3100 |
Description: | Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor. |
Causes: | Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective ISC PWB. Defective main PWB. |
Remedy: | The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary. Scanner motor 1. To check the scanner motor, execute U073. 2. Move the scanner by the hand to check whether it is unusually difficult to move. 3. Check that the optical wire rope is not disengaged and engage the wire. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the scanner motor. Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and ISC PWB (YC8) 3. Replace the home position sensor. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
Error code: | 3200 |
Description: | Exposure lamp error When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective LED lamp PWB. Defective ISC PWB. Defective main PWB. |
Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and main PWB (YC11) Defective LED lamp PWB. Replace the LED lamp PWB and check for correct operation. Defective ISC PWB. Replace the ISC PWB and check for correct operation. Defective CCD PWB. Replace the ISU and check for correct operation. Defective main PWB. Replace the main PWB and check for correct operation. |
Error code: | 3210 |
Description: | CIS lamp error When input value at the time of CIS illumination does not exceed the threshold value between 5 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Execute CCD of U061 lamp check. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. DP relay PWB Replace the DP relay PWB. |
Error code: | 3300 |
Description: | Optical system (AGC) error One of the gains is FF or 00 during the CCD lamp AGC is being processed. |
Causes: | Defective connector cable or poor contact in the connector. Defective exposure lamp Defective CCD PWB. Defective ISC PWB. Defective main PWB. |
Remedy: | LED lamp PWB 1. To check the lamp, execute U061 CCD. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. CCD PWB Replace the ISU and execute U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
Error code: | 3310 |
Description: | CIS AGC error After AGC, correct input is not obtained at CIS. |
Causes: | Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. To check the lamp, execute U061 CCD. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. |
Error code: | 3500 |
Description: | Communication error between scanner and ASIC An error code is detected. |
Causes: | Defective connector cable or poor contact in the connector. Defective ISC PWB. Defective main PWB. |
Remedy: | ISC PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ISC PWB (YC3) and Main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
Error code: | 3800 |
Description: | AFE error When writing the data, read and write data does not match 3 times in succession. No response is received in 100 ms from AEF. |
Causes: | Defective ISC PWB. |
Remedy: | ISC PWB 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. CCD PWB (YC2) and ISC PWB (YC9) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the ISC PWB and execute U411. CCD PWB Replace the ISU and execute U411. |
Error code: | 4001 |
Display: | ERROR E146-4001 Call for service. |
Description: | Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 4011 |
Description: | Polygon motor steady-state error After Polygon motor is stabilized, the ready signal is at the H level for 15 s continuously. |
Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 4102 |
Description: | BD initialization error C After polygon motor C is driven, the BD signal is not detected for 1 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB C. Defective engine PWB. |
Remedy: | PD PWB C (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 4103 |
Description: | BD initialization error M After polygon motor M is driven, the BD signal is not detected for 1 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB M. Defective engine PWB. |
Remedy: | PD PWB M (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 4104 |
Description: | BD initialization error Y After polygon motor Y is driven, the BD signal is not detected for 1 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB Y. Defective engine PWB. |
Remedy: | PD PWB Y (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 4201 |
Display: | Replace Drum:BK |
Description: | BD steady-state error K The BD signal is not detected. |
Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, shorted or grounded, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 4600 |
Display: | Maintenance Replace Laser |
Description: | LSU cleaning motor error After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s. After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective LSU cleaning motor. Defective engine PWB. |
Remedy: | LSU cleaning motor 1. Execute LSU cleaning using Adjustment/Maintenance of the system menu. 2. Rotate the drive gear and the cleaning spiral by the hand and check that they are not unusually loaded, and replace if it is damaged. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LSU cleaning motor and Engine PWB (YC21) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the LSU cleaning motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 4700 |
Display: | Supplies WT Box End Soon |
Description: | VIDEO_ASIC device error Communication with the video ASIC has failed 5 times successively. After writing to the VIDEO ASIC, the error that the reading value from the same address does not match occurs 8 times successively. |
Causes: | Engine PWB. Main PWB |
Remedy: | Main PWB 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Check that the connectors on the main PWB are properly connected, and if not, re-connect them. 3. Replace the main PWB. |
Error code: | 5101 |
Description: | Main high-voltage error K Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board). |
Causes: | Defective connector cable or poor contact in the connector. Defective high voltage PWB Defective engine PWB. |
Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. 3. Check that the discharger lamp is properly connected. Charger roller unit 1. Check that the high-voltage contacts are not distorted or adhered with foreign objects. 2. Reinstall the chrager roller unit.Or, replace the charger roller unit. High voltage PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. High voltage PWB (YC2) and Engine PWB (YC16) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the High voltage PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 5102 |
Description: | Main high-voltage error C Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board). |
Causes: | Defective connector cable or poor contact in the connector. Defective high voltage PWB 1. Defective engine PWB. |
Remedy: | Drum unit 1. Execute U030 Belt Mean Drum Motor and check that the drum motor can rotate. 2. Confirm that the drum or the drum screw can rotate. 3. Check that the discharger lamp is properly connected. 4. If it won’t rotate, replace the drum unit. Charger roller unit 1. Check that the high-voltage contacts are not distorted or adhered with foreign objects. 2. Reinstall the chrager roller unit.Or, replace the charger roller unit. High voltage PWB 1 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. High voltage PWB 1(YC2) and Engine PWB (YC16) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the High voltage PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 5103 |
Description: | Main high-voltage error M Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board). |
Causes: | Defective connector cable or poor contact in the connector. Defective high voltage PWB 1. Defective engine PWB. |
Remedy: | Drum unit 1. Execute U030 Belt Mean Drum Motor and check that the drum motor can rotate. 2. Confirm that the drum or the drum screw can rotate. 3. Check that the discharger lamp is properly connected. 4. If it won’t rotate, replace the drum unit. Charger roller unit 1. Check that the high-voltage contacts are not distorted or adhered with foreign objects. 2. Reinstall the chrager roller unit.Or, replace the charger roller unit. High voltage PWB 1 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. High voltage PWB 1(YC3) and Engine PWB (YC17) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the High voltage PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 5104 |
Description: | Main high-voltage error Y Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board). |
Causes: | Defective connector cable or poor contact in the connector. Defective high voltage PWB 1. Defective engine PWB. |
Remedy: | Drum unit 1. Execute U030 Belt Mean Drum Motor and check that the drum motor can rotate. 2. Confirm that the drum or the drum screw can rotate. 3. Check that the discharger lamp is properly connected. 4. If it won’t rotate, replace the drum unit. Charger roller unit 1. Check that the high-voltage contacts are not distorted or adhered with foreign objects. 2. Reinstall the chrager roller unit.Or, replace the charger roller unit. High voltage PWB 1 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. High voltage PWB 1(YC1) and Engine PWB (YC16) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the High voltage PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 6000 |
Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
Error code: | 6020 |
Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 6030 |
Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
Error code: | 6040 |
Description: | Fuser heater error Input from fuser center thermistor 1 is abnormal value continuously for 1 s. |
Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Defective fuser heater. Defective engine PWB. |
Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Center thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
Error code: | 6050 |
Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
Error code: | 6200 |
Display: | No Drum Unit Install the Drum Unit. |
Description: | Broken fuser edge heater wire Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser center thermistor 1 1. Replace the Fuser unit. |
Error code: | 6220 |
Description: | Abnormally high fuser edge thermistor temperature Fuser thermistor 2 detects a temperature higher than 240°C/464°F for 1 s. |
Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 2. Defective engine PWB. |
Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 6230 |
Description: | Broken fuser edge thermistor wire The Input signal from the fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser thermistor 1 is higher than 100°C/212°F. Fuser thermistor 2 detects a lower then 50°C/122°F for 15s during warming up. |
Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 2 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 6250 |
Description: | Abnormally low fuser edge thermistor temperature Fuser thermistor 2 detects a temperature lower than 100°C/212°F for 1 s during ready or print. |
Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 2. Defective fuser IH. Defective engine PWB. |
Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Fuser unit and Engine PWB (YC26) If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 6400 |
Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
Causes: | Fuser unit. |
Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
Error code: | 6610 |
Description: | Fuser release sensor error When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser release motor. Defective engine PWB. |
Remedy: | Fuser release motor 1. To check the motor operation, execute U030 Fuser Release. 2. Check that the drive gear can be rotated and the separation is possible. 3. If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Fuser unit. Fuser release sensor 1. Check that the sensor is correctly positioned. 2. Check that the sensor is not contaminated or damaged. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 6910 |
Description: | Engine software ready error The device won’t engage in ready state in 60 minutes after warming-up has began. (A previous timeout process has not been cancelled. |
Causes: | Defective connector cable or poor contact in the connector. Defective fuser rear fan motor. Defective engine PWB. |
Remedy: | Engine PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Reinstall the engine software. 3. Replace the engine PWB. |
Error code: | 7001 |
Description: | Toner motor error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
Causes: | Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB. |
Remedy: | Toner container 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7002 |
Description: | Toner motor C error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor C. Defective toner motor C. Defective engine PWB. |
Remedy: | Toner container C 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Screw sensor C 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor C and Engine PWB (YC27) 3. Replace the screw sensor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7003 |
Description: | Toner motor M error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor M. Defective toner motor M. Defective engine PWB. |
Remedy: | Toner container M 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Screw sensor M 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor M and Engine PWB (YC27) 3. Replace the screw sensor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7004 |
Description: | Toner motor Y error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor Y. Defective toner motor Y. Defective engine PWB. |
Remedy: | Toner container Y 1. Check that the spiral screw of the toner container can be rotated by the hand. 1. Check for broken gears and replace if any. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Screw sensor Y 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor Y and Engine PWB (YC27) 3. Replace the screw sensor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7101 |
Description: | Toner sensor error Sensor output value of 60 or less or 944 or more continued for 3 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB. |
Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7102 |
Description: | Toner sensor C error Sensor output value of 60 or less or 944 or more continued for 3 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor C 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit C are not damaged and the spiral can rotate. 5. Replace the Developer unit C. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7103 |
Description: | Toner sensor M error Sensor output value of 60 or less or 944 or more continued for 3 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor M 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit M are not damaged and the spiral can rotate. 5. Replace the Developer unit M. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7104 |
Description: | Toner sensor Y error Sensor output value of 60 or less or 944 or more continued for 3 s. |
Causes: | Defective connector cable or poor contact in the connector Defective engine PWB. |
Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor Y 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit Y are not damaged and the spiral can rotate. 5. Replace the Developer unit Y. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7200 |
Display: | Jam MP Tray Remove the jammed paper from MP Tray and press [Retry]. |
Description: | Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230. |
Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7210 |
Description: | Short-circuited outer temperature sensor The sensor input sampling is less than 69. |
Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7221 |
Description: | Broken LSU thermistor wire The sensor input sampling is greater than 230. |
Causes: | Defective connector cable or poor contact in the connector. Defective LSU thermistor. Defective engine PWB. |
Remedy: | LSU thermistor 1. Confirm LSU is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the laser scanner unit. LSU relay PWB REPLACE the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7231 |
Description: | Short-circuited LSU thermistor The sensor input sampling is less than 69. |
Causes: | Defective connector cable or poor contact in the connector. Defective LSU thermistor. Defective engine PWB. |
Remedy: | LSU thermistor 1. Confirm LSU is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the laser scanner unit. LSU relay PWB Replace the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7401 |
Description: | Developer unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
Remedy: | Different type of the developer unit is installed. Install the developer unit of the correct type. Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
Error code: | 7402 |
Description: | Developer unit C type mismatch error Absence of the developer unit C is detected. |
Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit C and front PWB (YC13) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
Error code: | 7403 |
Description: | Developer unit M type mismatch error Absence of the developer unit M is detected. |
Causes: | Defective connector cable or poor contact in the connector Different type of the developer unit is installed |
Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit M and front PWB (YC11) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
Error code: | 7404 |
Description: | Developer unit Y type mismatch error Absence of the developer unit Y is detected. |
Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit Y and front PWB (YC15) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
Error code: | 7411 |
Description: | Drum unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
Causes: | Defective connector cable or poor contact in the connector. Different type of the drum unit is installed. |
Remedy: | Different type of the drum unit is installed. Install the drum unit of the correct type. Drum unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum unit and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
Error code: | 7412 |
Description: | Drum unit type Mismatch error (Cyan) Improper adaptation of the main unit and drum unit is detected. |
Causes: | Drum unit C |
Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 7413 |
Description: | Drum unit type Mismatch error (Magenta) Improper adaptation of the main unit and drum unit is detected. |
Causes: | Drum unit M |
Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 7414 |
Description: | Drum unit type Mismatch error (Yellow) Improper adaptation of the main unit and drum unit is detected. |
Causes: | Drum unit Y |
Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 7601 |
Description: | ID sensor 1 error [Front] Dark potential error FrontDarkP and FrontDarkS are greater than 0.80V. Light potential error FrontBrightS is smaller than FrontDarkS. FrontBrightP is smaller than [FrontDarkP + 0.5V]. |
Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
Remedy: | ID sensor1 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor 1 (front) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7602 |
Description: | ID sensor 2 error [Rear] Dark potential error RearDarkP and RearDarkS are greater than 0.80V. Light potential error RearBrightS is smaller than RearDarkS. RearBrightP is smaller than [RearDarkP + 0.5V]. |
Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
Remedy: | ID sensor 2 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor2 (rear) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7611 |
Description: | Bias calibration reading value error (Black) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally |
Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 7612 |
Description: | Bias calibration reading value error (Cyan) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 7613 |
Description: | Bias calibration reading value error (Magenta) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 7614 |
Description: | Bias calibration reading value error (Yellow) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 7620 |
Description: | Color Registration timing of detection Color patches printed on the primary transfer belt are not within the ID sensor readable range. Or the poor density occurs. |
Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
Remedy: | Primary transfer belt ID sensor LSU 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. 8. When checking the printing position of the color, if any color shift occurs, re-install the LSU and the drum unit. 9. If not corrected, replace the LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 7800 |
Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7810 |
Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
Error code: | 7901 |
Description: | Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB. |
Remedy: | DR PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7902 |
Description: | Drum C EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB C. |
Remedy: | DR PWB- C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB- C and Front PWB (YC12) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit C. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7903 |
Description: | Drum M EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB M. |
Remedy: | DR PWB- M 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB- M and Front PWB (YC10) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit M. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7904 |
Description: | Drum Y EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB Y. |
Remedy: | DRPWB- Y 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DRPWB- Y and Front PWB (YC14) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit Y. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7911 |
Description: | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
Causes: | Defective connector cable or poor contact in the connector. Defective developer unit. |
Remedy: | Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7912 |
Description: | Developer unit C EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
Causes: | Defective connector cable or poor contact in the connector. Defective developer unit C. |
Remedy: | Developer unit C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit C. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7913 |
Description: | Developer unit M EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
Causes: | Defective connector cable or poor contact in the connector. Defective developer unit M. |
Remedy: | Developer unit M 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit M. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 7914 |
Description: | Developer unit Y EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
Causes: | Defective connector cable or poor contact in the connector. Defective developer unit Y. |
Remedy: | Developer unit Y 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit Y. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 8000 |
Display: | Print Overrun |
Description: | Finisher incompatible detection error The finisher has been installed with a device to which it is incompatible. |
Causes: | The finisher is installed with a device to which it is incompatible. |
Remedy: | The finisher is installed with a device to which it is incompatible. The finisher must be installed with the devices to which it is compatible. |
Error code: | 8010 |
Description: | Punch motor error 1 When the punch motor is driven, punch home position sensor does not turn on within 200 ms. |
Causes: | Defective connector cable or poor contact in the connector. Defective punch home position sensor. Defective punch motor. Defective PWB. |
Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch home position sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch home position sensor and Punch PWB (YC8) 4. Replace the Punch home position sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8020 |
Description: | Punch motor error 2 Home position is not obtained in 3 s after home position is initialized or in standby. |
Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8030 |
Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8090 |
Description: | DF paddle motor error When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF paddle sensor. Defective DF paddle motor. Defective DF main PWB. |
Remedy: | DF paddle motor 1. Execute U240 Motor - Beat to check the finisher operation. 2. Check that the paddle can rotate. 3. Check that the drive from the motor reaches the paddle. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle motor and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF paddle motor. DF paddle sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8100 |
Description: | DF eject release motor error When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF bundle discharge sensor. Defective DF eject release motor. Defective DF main PWB. |
Remedy: | DF eject release motor DF bundle discharge unit sensor 1. Execute U240 Motor - Eject Unlock (Full) to check the finisher operation. 2. Check that the eject guide of the process tray is opened and, if not, correct the guide. 3. Check that the drive from the motor reaches the eject guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF eject release motor. DF bundle discharge unit sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 4. Replace the DF bundle eject unit sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8140 |
Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8150 |
Description: | DF tray motor error 2 When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF main PWB (YC22) DF tray upper surface sensor and DF main PWB (YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8160 |
Description: | DF tray motor error 3 When the main tray has descended, DF tray sensor 4 does not turn on within 20 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF tray sensor 3. Defective DF tray motor. Defective DF main PWB. |
Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 4 1. Execute U241 Finisher - Tray Middle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 4 and DF main PWB (YC23) 4. Replace the DF tray sensor 4. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8170 |
Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8180 |
Description: | DF side registration motor 1 error 2 JAM6810 (jam in front of width alignment) is detected twice. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1. 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8190 |
Description: | DF side registration motor 2 error 1 When initial operation, DF side registration sensor 2 does not turn on within 3 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8200 |
Description: | DF side registration motor 2 error 2 JAM6910 (jam in rear of width alignment) is detected twice. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8210 |
Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8230 |
Description: | DF staple motor error 1 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF staple motor. Defective DF main PWB. |
Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF staple sensor Replace the staple unit. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8250 |
Description: | DF tray motor error 4 The lock signal of the motor is detected continuously for 10 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective DF tray motor. Defective DF main PWB. |
Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF tray motor and DF main PWB (YC16) DF tray sensor 3 and DF main PWB (YC23) Defective DF tray motor. Replace the DF tray motor. Defective DF main PWB. Replace the DF main PWB and check for correct operation. |
Error code: | 8260 |
Description: | DF middle motor home position error DF paddle sensor is not turned on within 1s after driving the DF middle motor. |
Causes: | DF middle motor. DF paddle sensor. DF main PWB |
Remedy: | DF middle motor 1. Execute U240 Motor - Middle(H)(L). 2. Check that the drive from the motor reaches the paddle. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF middle motor and DF main PWB (YC12) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF middle motor. DF paddle sensor 1. Execute U241 Finisher - Lead Paddle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
Error code: | 8410 |
Description: | Punch slide motor error 1 The punch slide sensor won’t turn On when home position has been moved by 30 mm. |
Causes: | Defective connector cable or poor contact in the connector. Defective slide sensor. Defective punch slide motor. Defective PWB. |
Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch slide sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide sensor and Punch PWB (YC6) 4. Replace the punch slide sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB |
Error code: | 8420 |
Description: | Punch slide motor error 2 In detection of paper edges, the paper edge cannot be detected in 30 mm move. |
Causes: | Defective connector cable or poor contact in the connector. Defective punch slide motor. Defective PWB. |
Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch paper edge sensor 1,2 1. Execute U241 Punch - Edge Face 1,2,3,4 to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch paper edge sensor 1,2 and Punch PWB (YC5,YC7) 4. Replace the punch paper edge sensor 1,2. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
Error code: | 8430 |
Description: | Punch unit communication error Communication with the punch unit is not possible. |
Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
Remedy: | Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
Error code: | 8500 |
Description: | Mailbox communication error Communication failed to be established after the mailbox was hooked up. |
Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
Remedy: | MB main PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB main PWB (YC3) and DF main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB main PWB DF main PWB Replace the DF main PWB |
Error code: | 8510 |
Description: | MB conveying motor error 1 When initial operation, MB home position sensor does not turn on within 5 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor. Defective MB main PWB. |
Remedy: | MB conveying motor 1. If the transfer roller won’t rotate smoothly, repair its mechanism. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
Error code: | 8520 |
Description: | MB conveying motor error 2 When standby operation, MB home position sensor does not turn off within 1 s. |
Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor Defective MB main PWB. |
Remedy: | MB conveying motor 1. Execute Mail Box - Conv of U240 finisher operation check. 2. Manipulate the conveying roller of the mailbox to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
Error code: | 8800 |
Description: | Document finisher main program error Document finisher main program error at power up. |
Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
Error code: | 8900 |
Description: | Document finisher backup error Read and write data does not match 3 times in succession. |
Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective DF main PWB. |
Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB |
Error code: | 8990 |
Description: | Finisher setup error In case the bridge (AK) is not installed while the DF is connected. (35/40 ppm model only) |
Causes: | Bridge unit Document finisher. DF main PWB. Engine PWB |
Remedy: | Finisher 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DF main PWB - Engine PWB(YC24): 30 ppm model - Engine PWB(YC31): 35/40 ppm models 2. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. DF main PWB 1. Check EEPROM mount and correct it. 2. Replace the DF main PWB. |
Error code: | 9070 |
Description: | Communication error between DP and SHD A communication error is detected. |
Causes: | Defective connector cable or poor contact in the connector. Defective DPSHD PWB. |
Remedy: | DP SHD PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP SHD PWB. |
Error code: | 9180 |
Description: | DP feed-shift motor error The HP cannot be detected even after executing the HP detection retrial 3 consecutive times. HP detection: when the DP feed-shift motor is driven to move to the HP, the HP is not detected after it is rotated once. |
Causes: | DP feed-shift motor. DP feed-shift sensor |
Remedy: | DP feed-shift motor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Confirm that the connector of the DP feed-shift motor is firmly connected, and if necessary, push the unit all the way in. 3. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DP feed-shift motor - Engine PWB (YC6) 4. If the wire is disconnected, short-circuited or has a ground fault, or the connector pin is deformed, replace the wire. 5. Replace the DF feed-shift motor. DP feed-shift sensor 1. Rotate the DP feed-shift motor manually to check that it is not unusually difficult to rotate. 2. Check if the DP feed-shift sensor is out of position because it has dropped off and if the sensor light is interrupted by the actuator. 3. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DP feed-shift sensor - DP main PWB (YC4) DP main PWB - Engine PWB (YC6) 4. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. 5. Replace the DP feed-shift sensor. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
Error code: | 9500 |
Description: | ISC PWB error A |
Causes: | Main PWB. ISC PWB. |
Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC PWB 4. Contact the Service Support. |
Error code: | 9510 |
Description: | ISC PWB error B |
Causes: | Main PWB. DP SHD PWB. |
Remedy: | Main PWB DP SHD PWB 1. Reinsert the connector if its connection is loose. DP relay PWB (YC2) and DP SHD PWB (YC3) 2. Replace the main PWB. 3. Replace the DP SHD PWB. 4. Contact the Service Support. |
Error code: | 9530, 9540, 9550 |
Description: | Backup data error The internal data changes by replacing multiple parts at the same time, interfering with the machine operation and will not enter ready mode. |
Remedy: | PWBs In case two or more of the parts below were replaced at the same time, reattach them. Applicable parts: Memory, PWBs *When replacing the applicable parts, 2 or more do not replace then at the same time. *When replacing the above applicable parts, do not work the following at the same time. Replace the drum unit or the developing unit. Replace the drum unit for one color with another in the same machine. |
Error code: | F000 |
Description: | Communication error between the main unit and CPU |
Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
Error code: | F010 |
Description: | Program read error (SSD) |
Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
Error code: | F020 |
Description: | System memory error (RAM reading/writing error or CPU memory error) |
Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
Error code: | F040 |
Description: | Option installation error |
Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
Error code: | F050 |
Description: | Engine main program error |
Causes: | The engine program cannot start up. |
Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
Error code: | F12X |
Description: | An error is detected at the Scan control section |
Remedy: | 1) Check connection of the harness (Scan/DP - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the Scan/DP board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F13X |
Description: | An error is detected at the Panel control section |
Remedy: | 1) Check connection of the harness (Panel - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the panel board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F14X |
Description: | An error is detected at the FAX control section |
Remedy: | 1) Check connection of the harness (FAX - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check function. (Take cae of the received data since it is cleared) 5) Replace the FAX_DIMM and check function. 6) Replace the FAX board and check function. 7) Replace the main board and check function. 8) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F15X |
Description: | An error is detected at the authentication device control section |
Remedy: | 1) Check connection of the harness (Authentication device - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F18X |
Description: | An error is detected at the Video control secion |
Remedy: | 1) Check connection of the harness (Engine - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the engine board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F1DX |
Description: | An error is detected at the Image memory management section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. *The F1D4 error is RAM allocation error. -1Check it with the U340 -2Initialize the setting valued with the U021 |
Error code: | F21X, F22X, F23X |
Description: | An error is detected at the Image processing section |
Remedy: | 1) Check contact of the DDR memory and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F24X |
Description: | An error is detected at the System management section |
Remedy: | 1) Check contact of the DDR memory and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F25X |
Description: | An error is detected at the Network management section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Retrieve the USBLOG and contact the Service Administratuve Division. (or retrieve the packet capture data depending on the reult of analysis) |
Error code: | F26X ... F2AX |
Description: | An error is detected at the System management section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F2BX ... F32X |
Description: | An error is detected at the Network control section |
Causes: | [Main body to External network] Ethernet connector |
Remedy: | 1. Format the HDD and check function. (U024 FULL formatting) * 2. Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3. Replace the Main PWB and check function. 4. Retrieve the USBLOG and the packet capture data and contact the Service Administratuve Division. *: HDD standard model only |
Error code: | F33X |
Description: | An error is detected at the Scan management section |
Remedy: | 1) Check connection of the harness (Scan/DP board - main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the Scan/DP board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F34X |
Description: | An error is detected at the Panel management section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F35X |
Description: | An error is detected at the Print control section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F37X |
Description: | An error is detected at the FAX management section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check function. (Take cae of the received data since it is cleared) 4) Replace the FAX_DIMM and check function. 5) Replace the main board and check function. 6) Replace the HDD and check function. 7) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F38X |
Description: | An error is detected at the Authentication/permit management section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F39X |
Description: | An error is detected at the KMAS management section |
Remedy: | 1. Check connection of the harness (KMAS - Main PWB) and connectors and check function. 2. Format the HDD and check function. (U024 FULL formatting) * 3. Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4. Replace the Main PWB and check function. 5. Replace the HDD and check function. * 6. Retrieve the USBLOG and contact the Service Administrative Division. *: HDD standard model only |
Error code: | F3AX ... F41X |
Description: | An error is detected at the Entity control section |
Remedy: | 1. Format the HDD and check function. (U024 FULL formatting) * 2. Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3. Replace the Main PWB and check function. 4. Replace the HDD and check function. * 5. Retrieve the USBLOG and contact the Service Administrative Division. *: HDD standard model only |
Error code: | F42X ... F46X |
Description: | An error is detected at the Print image process section |
Remedy: | 1. Replace the Main PWB and check function. 2. Retrieve the USBLOG (or retrieve the print capture data by case) |
Error code: | F47X, F48X, F49X |
Description: | An error is detected at the Image edit process control section |
Remedy: | 1. Format the HDD and check function. (U024 FULL formatting) * 2. Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3. Replace the Main PWB and check function. 4. Replace the HDD and check function. * 5. Retrieve the USBLOG and contact the Service Administrative Division. *: HDD standard model only |
Error code: | F4AX, F4CX |
Description: | An error is detected at the Print image process section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F4DX, F4EX |
Description: | An error is detected at the Entity control section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F50X |
Description: | An error is detected at the FAX control section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F51XF ... 57X |
Description: | An error is detected at the Job control section |
Remedy: | 1. Format the HDD and check function. (U024 FULL formatting) * 2. Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3. Replace the Main PWB and check function. 4. Replace the HDD and check function. * 5. Retrieve the USBLOG and contact the Service Administrative Division. *: HDD standard model only |
Error code: | F58X ... F5EX |
Description: | An error is detected at the Service management section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F62X |
Description: | An error is detected at the Service execution section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F68X |
Description: | An error is detected at the Storage device control section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Error code: | F69X ... F6CX |
Description: | An error is detected at the HyPAS control section |
Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
Парткод
Название
Kyocera Блок фотобарабана
Kyocera Блок проявки голубой
Kyocera Блок проявки черный
Kyocera Блок проявки пурпурный
Kyocera Блок проявки желтый
Kyocera Блок термозакрепления
Kyocera Сервисный комплект
Kyocera Сервисный комплект
Kyocera Тонер-картридж голубой
Kyocera Тонер-картридж черный
Kyocera Тонер-картридж пурпурный
Kyocera Тонер-картридж желтый
Kyocera Контейнер для отработанного тонера