Kyocera TASKalfa 4003i
Рейтинг
Модули
Frame Front
Paper Conveying Section 1
Electrical Components 3
TRANSFER SECTION
Paper Conveying Section 3
Operation Section
Paper Conveying Section 7
ELECTRICAL COMPONENTS 2
SCANNER SECTION 2
Paper Conveying Section 6
Paper Conveying Section 5
Frame Base
Paper Feed Section 1
DRIVE SECTION 2
Image Formation Section
DRIVE SECTION 3
Electrical Components 1
Exit Section 2
Paper Feed Section 3
Paper Cassette 2
Exit Section 1
Covers 1
Covers 3
Scanner Section 1
Frame Top
Covers 2
Drive Section 1
Frame Right
Paper Cassette 1
Paper Conveying Section 2
DRIVE SECTION 4
Fuser Section
Developer Section
Laser Scanner Section
PAPER FEED SECTION 2
Paper Conveying Section 4
Детали Paper Conveying Section 7
| Деталь: | COVER FRONT CONTAINER MONO |
| Парткод: | 302NK04020 |
| Деталь: | REINFORCEMENT INNER COVER |
| Парткод: | 302NK04030 |
| Деталь: | SHAFT COVER CONTAINER |
| Парткод: | 302ND04950 |
| Деталь: | COVER CONTAINER K |
| Парткод: | 302ND04780 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302H004660 |
| Деталь: | STOPPER 3 |
| Парткод: | 302LF12410 |
| Деталь: | MOUNT INTERLOCK |
| Парткод: | 302ND04321 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | PLATE INTERLOCK |
| Парткод: | 302ND04460 |
| Деталь: | SPRING INTERLOCK |
| Парткод: | 302ND04370 |
| Деталь: | PIN INTERLOCK |
| Парткод: | 302ND04510 |
| Деталь: | PIN GUIDE CHUTE |
| Парткод: | 302GR25241 |
| Деталь: | SPRING FUSER |
| Парткод: | 302F931270 |
| Деталь: | KEY POWER |
| Парткод: | 302ND04870 |
| Деталь: | PARTS SPEAKER SP |
| Парткод: | 302ND94790 |
| Деталь: | PARTS PWB SWITCH ASSY SP |
| Парткод: | 302NG94300 |
| Деталь: | HOLDER MAIN KEY |
| Парткод: | 302NG04210 |
| Деталь: | PARTS HUMAN DETECT ASSY SP |
| Парткод: | 302V894070 |
| Деталь: | HOLDER HUMAN DETECT SENSOR |
| Парткод: | 302V804580 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000007+H01 |
| Деталь: | PARTS COVER FRONT CONT MONO ASSY SP |
| Парткод: | 302NK94131 |
| Деталь: | COVER RIGHT |
| Парткод: | 302ND29012 |
| Деталь: | BUSH 8 |
| Парткод: | 302NG08250 |
| Деталь: | ACTUATOR PAPER SET |
| Парткод: | 302ND08390 |
| Деталь: | ACTUATOR PAPER LINK |
| Парткод: | 302ND08560 |
| Деталь: | SHAFT FEED MPF |
| Парткод: | 302ND08300 |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | 302HN31660 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | BUSH 6 R |
| Парткод: | 302ND08590 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302ND08670 |
| Деталь: | MOUNT PI |
| Парткод: | 302ND08580 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | HOLDER SENSOR MPF |
| Парткод: | 302ND29600 |
| Деталь: | CONN.CORD ASSY MPF SET SENSOR |
| Парткод: | 302ND46651 |
| Деталь: | WIRE MPF |
| Парткод: | 302V808010 |
| Деталь: | HOOK WIRE MPF |
| Парткод: | 302ND08920 |
| Деталь: | COVER SIDE DECK |
| Парткод: | 302ND29320 |
| Деталь: | STRAP RIGHT COVER B |
| Парткод: | 302ND29610 |
| Деталь: | STRAP RIGHT COVER A |
| Парткод: | 302ND29170 |
| Деталь: | PARTS RIGHT COVER ASSY SP |
| Парткод: | 302ND94743 |
| Деталь: | PARTS UNIT HIGH VOLTAGE TRANSFER SP |
| Парткод: | 302NK94120 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | COVER WIRE EJECT |
| Парткод: | 302ND39310 |
| Деталь: | BASE TERMINAL HV |
| Парткод: | 302ND39170 |
| Деталь: | SPRING HV SEPARATION |
| Парткод: | 302ND39250 |
| Деталь: | SPRING HV DRIVE |
| Парткод: | 302ND39240 |
| Деталь: | SPRING HV TC BK |
| Парткод: | 302ND39230 |
| Деталь: | SPRING TRANSFER CLN BIAS |
| Парткод: | 302ND39180 |
| Деталь: | STOPPER 3 |
| Парткод: | 302LF12410 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610004++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | PLATE OPTION |
| Парткод: | 302K339050 |
| Деталь: | LID SHIELD IH PWB |
| Парткод: | 302ND39050 |
| Деталь: | MOUNT PI |
| Парткод: | 302ND04930 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | MOUNT CONNECTOR |
| Парткод: | 302ND17350 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC16M1040+H01 |
| Деталь: | FILM FFC CCD REAR |
| Парткод: | 302V817030 |
| Деталь: | GUIDE WIRE CONT BOX |
| Парткод: | 302ND39030 |
| Деталь: | PARTS WIFI UNIT SP |
| Парткод: | 303RR94010 |
| Деталь: | COVER CONNECTOR FEED |
| Парткод: | 302ND29700 |
| Деталь: | PARTS STORAGE DEVICE SP |
| Парткод: | 302ND93180 |
| Деталь: | BRACKET HDD |
| Парткод: | 302RH39160 |
| Деталь: | BUSHING FAN |
| Парткод: | 302JD19140 |
| Деталь: | PIN HDD |
| Парткод: | 302MV39341 |
| Деталь: | PLATE EARTH FFC |
| Парткод: | 302NH17070 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+024H01 |
| Деталь: | PARTS MOTOR BL INNER W10 SP |
| Парткод: | 302ND94500 |
| Деталь: | TR-6500 |
| Парткод: | 302NK93033 |
| Деталь: | SHEET WIRE MPF |
| Парткод: | 302ND29640 |
| Деталь: | PULLEY LEFT FRAME |
| Парткод: | 302H017120 |
| Деталь: | STUD SCREW |
| Парткод: | 302ND08950 |
| Деталь: | JOINT COVER HOOK |
| Парткод: | 302ND29240 |
| Деталь: | SPRING HOOK |
| Парткод: | 302K304540 |
| Деталь: | PLATE DU GUIDE |
| Парткод: | 302ND29350 |
| Деталь: | SPRING EARTH SW |
| Парткод: | 302ND29680 |
| Деталь: | ACTUATOR DU UPPER |
| Парткод: | 302ND29500 |
| Деталь: | SPRING ACTUATOR PI |
| Парткод: | 302ND06720 |
| Деталь: | SHAFT COVER RIGHT |
| Парткод: | 302ND29570 |
| Деталь: | LEVER COVER RIGHT |
| Парткод: | 302ND29560 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | HOOK COVER RIGHT F |
| Парткод: | 302ND29140 |
| Деталь: | HOOK COVER RIGHT R |
| Парткод: | 302ND29550 |
| Деталь: | HOLDER RETARD MPF |
| Парткод: | 302ND08400 |
| Деталь: | RETARD ROLLER ASSY |
| Парткод: | 302F909171 |
| Цена: | 900 ₽ |
| Деталь: | GUIDE RETARD MPF |
| Парткод: | 302ND08500 |
| Деталь: | SHEET GUIDE RETARD |
| Парткод: | 302ND08800 |
| Деталь: | SPRING RETARD LOW |
| Парткод: | 302ND08450 |
| Деталь: | PARTS PULLEY FEED ASSY SP |
| Парткод: | 302ND94380 |
| Деталь: | SPRING FEED MPF |
| Парткод: | 302ND08550 |
| Деталь: | PIN FEED ROLLER |
| Парткод: | 302ND08530 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | BUSH DU EW |
| Парткод: | 302K924830 |
| Деталь: | PIN CLUTCH MPF |
| Парткод: | 302ND08660 |
| Деталь: | PARTS CLUTCH 35 Z35R SPRING SP |
| Парткод: | 302ND94680 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302ND08670 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PIN CLUTCH DU |
| Парткод: | 302ND29380 |
| Деталь: | GEAR Z23R |
| Парткод: | 302ND29210 |
| Деталь: | PLATE DRIVE DU |
| Парткод: | 302ND29180 |
| Деталь: | BUSH DU |
| Парткод: | 302F929140 |
| Деталь: | GEAR Z44R-Z22L |
| Парткод: | 302ND29200 |
| Деталь: | GEAR Z35L |
| Парткод: | 302ND29190 |
| Деталь: | GEAR Z47L |
| Парткод: | 302ND29220 |
| Деталь: | PLATE EARTH RIGHT COVER |
| Парткод: | 302ND29480 |
| Деталь: | HOLDER SENSOR DU |
| Парткод: | 302ND29590 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000007+H01 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | CONN.CORD ASSY DU SENSOR |
| Парткод: | 302ND46140 |
| Деталь: | SPRING HOOK UPPER |
| Парткод: | 302ND29750 |
| Деталь: | SHEET PAD BOTTOM |
| Парткод: | 303RC10260 |
| Деталь: | SHEET GUIDE RETARD A |
| Парткод: | 302ND08850 |
| Деталь: | PARTS RIGHT COVER ASSY SP |
| Парткод: | 302ND94743 |
| Деталь: | PARTS TABLET OPERATION SP |
| Парткод: | 302V894080 |
| Деталь: | PARTS PWB NFC ASSY SP |
| Парткод: | 302RH94050 |
| Деталь: | PARTS PWB OPERATION ASSY SP |
| Парткод: | 302V894060 |
| Деталь: | PARTS LCD OPERATION SP |
| Парткод: | 302V894090 |
| Деталь: | PARTS PWB PANEL ASSY SP |
| Парткод: | 302V894050 |
| Деталь: | CONN.CORD ASSY OPERATION |
| Парткод: | 302V846070 |
| Деталь: | CONN.CORD ASSY 10KEY JOINT |
| Парткод: | 302V846080 |
| Деталь: | PARTS OPERATION UNIT H SP |
| Парткод: | 302V894121 |
| Деталь: | COVER MPF |
| Парткод: | 302ND08100 |
| Деталь: | TABLE MPF |
| Парткод: | 302ND08111 |
| Деталь: | BASE LIFT MPF |
| Парткод: | 302ND08121 |
| Деталь: | TRAY MPF A |
| Парткод: | 302ND08171 |
| Деталь: | TRAY MPF B |
| Парткод: | 302ND08181 |
| Деталь: | PLATE BOTTOM MPF |
| Парткод: | 302ND08150 |
| Деталь: | CURSOR MPF R |
| Парткод: | 302ND08140 |
| Деталь: | CURSOR MPF F |
| Парткод: | 302ND08130 |
| Деталь: | HOLDER DETECTION |
| Парткод: | 302ND08200 |
| Деталь: | GEAR DETECTION |
| Парткод: | 302ND08210 |
| Деталь: | GEAR 18 BYPASS |
| Парткод: | 302ND08220 |
| Деталь: | PARTS PWB PAPER SIZE SENSOR ASSY SP |
| Парткод: | 303R394050 |
| Деталь: | CONN.CORD ASSY MPF TABLE |
| Парткод: | 302ND46150 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302ND08821 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | ACTUATOR SIZE DETECTION |
| Парткод: | 302K908211 |
| Деталь: | SPRING-TORSION SIZE DETECTION |
| Парткод: | 302K908220 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000007+H01 |
| Деталь: | STRAP LINK MPF |
| Парткод: | 302R408230 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 302R408220 |
| Деталь: | SPRING BYPASS TABLE F |
| Парткод: | 302ND08830 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | LABEL MPF PAPER LIMIT |
| Парткод: | 302ND08700 |
| Деталь: | Label Operation |
| Парткод: | 302ND08740 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | STOPPER MULTI |
| Парткод: | 302 R408170 |
| Деталь: | SPRING-COMPRESSION LIFT |
| Парткод: | 302ND08160 |
| Деталь: | PARTS RIGHT COVER ASSY SP |
| Парткод: | 302ND94743 |
| Деталь: | PARTS MPT TRAY ASSY SP |
| Парткод: | 302ND94202 |
| Деталь: | PARTS PWB IH 100 ASSY SP |
| Парткод: | 302ND94300 |
| Деталь: | PARTS PWB IH 200 ASSY SP |
| Парткод: | 302ND94310 |
| Деталь: | PARTS UNIT LOW VOLTAGE SP |
| Парткод: | 302V894101 |
| Деталь: | FILM LVU PWB |
| Парткод: | 302ND39270 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510021++H01 |
| Деталь: | GUIDE WIRE MAIN A |
| Парткод: | 302ND39100 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | PLATE SHIELD LSU |
| Парткод: | 302ND39330 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | GUIDE WIRE LVU |
| Парткод: | 302ND39140 |
| Деталь: | PLATE INLET |
| Парткод: | 302V839020 |
| Деталь: | SW.SEESAW |
| Парткод: | 7SC020204+++H01 |
| Деталь: | ACCESS.COVER CONN. |
| Парткод: | 7YZC210002++H01 |
| Деталь: | SHIELD LVU PWB |
| Парткод: | 302ND39060 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | COVER LVU PWB |
| Парткод: | 302ND02610 |
| Деталь: | SHIELD IH PWB |
| Парткод: | 302ND39040 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | REINFORCEMENT REAR FRAME |
| Парткод: | 302ND02620 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210011++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210010++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210009++H01 |
| Деталь: | DUCT IH PWB EXIT A |
| Парткод: | 302ND33101 |
| Деталь: | FILM DUCT EXHAUST |
| Парткод: | 302ND33110 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | DUCT EXIT B |
| Парткод: | 302ND33200 |
| Деталь: | DUCT EXIT A |
| Парткод: | 302ND33190 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC03B1106+H01 |
| Деталь: | PARTS FAN CENTER 60 15 SP |
| Парткод: | 302ND94600 |
| Деталь: | PARTS UNIT HIGH VOLTAGE MAIN SP |
| Парткод: | 302NK94110 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | MOUNT DRAWER |
| Парткод: | 302ND02510 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | CONN.CORD ASSY PF DRAWER |
| Парткод: | 302ND46210 |
| Деталь: | PLATE OPTION COIN VENDOR |
| Парткод: | 302ND39160 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510023++H01 |
| Деталь: | SHEET WASTE SCREW INNER |
| Парткод: | 302KV03330 |
| Деталь: | MOUNT DRIVE |
| Парткод: | 302ND17140 |
| Деталь: | PARTS MOTOR ISU SP |
| Парткод: | 302N294010 |
| Деталь: | COVER ISU FRONT |
| Парткод: | 302ND04122 |
| Деталь: | FILM FRAME SIDE R |
| Парткод: | 302ND17400 |
| Деталь: | FILM FRAME SIDE L |
| Парткод: | 302ND17410 |
| Деталь: | BELT ISU |
| Парткод: | 302ND17210 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 302ND17270 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | SWITCH RELEASE |
| Парткод: | 302ND17280 |
| Деталь: | SPRING RELEASE SWITCH |
| Парткод: | 302GR17380 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | MOUNT PI |
| Парткод: | 302K317330 |
| Деталь: | FILM FRAME |
| Парткод: | 302K317660 |
| Деталь: | SEAL FRAME ISU C |
| Парткод: | 302K317650 |
| Деталь: | SEAL FRAME ISU A |
| Парткод: | 302K317450 |
| Деталь: | SEAL FRAME ISU B |
| Парткод: | 302K317460 |
| Деталь: | COVER ISU CONTACT LEFT |
| Парткод: | 302ND04200 |
| Деталь: | COVER ISU CONTACT REAR |
| Парткод: | 302ND04220 |
| Деталь: | COVER ISU CONTACT FRONT |
| Парткод: | 302ND04210 |
| Деталь: | COVER ISU CONTACT RIGHT |
| Парткод: | 302ND04190 |
| Деталь: | PIN FUSER |
| Парткод: | 302LV25420 |
| Деталь: | COVER ISU LEFT SUB |
| Парткод: | 302RH04230 |
| Деталь: | MOUNT KEYBOARD |
| Парткод: | 302ND04920 |
| Деталь: | MOUNT PWB USB |
| Парткод: | 302ND04860 |
| Деталь: | PARTS PWB USB HUB ASSY SP |
| Парткод: | 302RH94020 |
| Деталь: | SHEET GLASS |
| Парткод: | 303LL02500 |
| Деталь: | PARTS CONTACT-GLASS ASSY(I) SP |
| Парткод: | 302RH94150 |
| Деталь: | PARTS CONTACT-GLASS ASSY(C) SP |
| Парткод: | 302RH94160 |
| Деталь: | ARM LINK PRESS RELEASE |
| Парткод: | 302ND24110 |
| Деталь: | LEVER BASE CONVEYING F |
| Парткод: | 302ND24090 |
| Деталь: | SPRING HOOK CONVEYING F |
| Парткод: | 302ND24460 |
| Деталь: | LEVER BASE CONVEYING R |
| Парткод: | 302ND24100 |
| Деталь: | SPRING HOOK CONVEYING R |
| Парткод: | 302ND24470 |
| Деталь: | BUSH REGIST |
| Парткод: | 302ND24350 |
| Деталь: | SPRING-COMPRESSION REGIST R |
| Парткод: | 302K924050 |
| Деталь: | HOLDER REGIST |
| Парткод: | 302ND24390 |
| Деталь: | PARTS ROLLER REGIST R SP |
| Парткод: | 302ND94400 |
| Деталь: | SPRING-COMPRESSION REGIST F |
| Парткод: | 302K924040 |
| Деталь: | GUIDE REGIST R |
| Парткод: | 302ND24320 |
| Деталь: | SHEET REGIST R |
| Парткод: | 302ND24340 |
| Деталь: | BUSH DU EW |
| Парткод: | 302K924830 |
| Деталь: | GEAR Z22R |
| Парткод: | 302K924060 |
| Деталь: | SPRING GUIDE REGIST |
| Парткод: | 302ND24360 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | COLLAR ROLLER |
| Парткод: | 302NG24350 |
| Деталь: | PIN CONVEYING |
| Парткод: | 302ND24450 |
| Деталь: | STOPPER 3 |
| Парткод: | 302LF12410 |
| Деталь: | SPRING GUIDE TRANSFER |
| Парткод: | 302ND22150 |
| Деталь: | BEARING MR126ZZ |
| Парткод: | 7BE006124431H01 |
| Деталь: | MOUNT SECONDLY TRANSFER F |
| Парткод: | 302ND22100 |
| Деталь: | GEAR SECONDLY TRANSFER Z25 |
| Парткод: | 302ND22030 |
| Деталь: | ARM GUIDE TRANSFER F |
| Парткод: | 302ND22130 |
| Деталь: | ARM GUIDE TRANSFER R |
| Парткод: | 302ND22140 |
| Деталь: | GUIDE SECONDLY TRANSFER |
| Парткод: | 302ND22090 |
| Деталь: | PARTS ROLLER SECONDLY TRANSFER SP |
| Парткод: | 302ND94390 |
| Деталь: | PARTS RIGHT COVER ASSY SP |
| Парткод: | 302ND94743 |
| Деталь: | PARTS ROLLER SECONDRY TRANSFER ASSY SP |
| Парткод: | 302ND94180 |
| Деталь: | BASE CONVEYING |
| Парткод: | 302ND24010 |
| Деталь: | SHAFT FEED |
| Парткод: | 302ND29280 |
| Деталь: | PULLEY FEED 16 |
| Парткод: | 302ND29260 |
| Деталь: | SPRING-COMPRESSION PULLEY FEED |
| Парткод: | 302ND29300 |
| Деталь: | CAP SPRING |
| Парткод: | 302ND24290 |
| Деталь: | CAP HOLDER SHAFT |
| Парткод: | 302ND29630 |
| Деталь: | SPRING SEPARATE CONVEYING |
| Парткод: | 302ND24440 |
| Деталь: | PLATE EARTH CONVEYING |
| Парткод: | 302ND24050 |
| Деталь: | PLATE HV CONVEYING |
| Парткод: | 302ND24040 |
| Деталь: | ACTUATOR DU |
| Парткод: | 302ND24070 |
| Деталь: | SPRING ACTUATOR DU |
| Парткод: | 302ND24430 |
| Деталь: | HOLDER PUSH REGIST |
| Парткод: | 302ND24200 |
| Деталь: | SPRING-COMPRESSION REGIST CENTER |
| Парткод: | 302ND24210 |
| Деталь: | BUSH REGIST CENTER |
| Парткод: | 302K924430 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302K994360 |
| Деталь: | SEAL COOLING FAN C |
| Парткод: | 302K903560 |
| Деталь: | SCREW FAN |
| Парткод: | 302H733430 |
| Деталь: | SHEET DUCT FUSER EDGE A |
| Парткод: | 302ND33810 |
| Деталь: | LABEL A5 |
| Парткод: | 302ND34290 |
| Деталь: | PLATE CONVEYING TC |
| Парткод: | 302ND24220 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 303NW94060 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | HOLDER SECONDLY TRANSFER |
| Парткод: | 302ND22040 |
| Деталь: | SPRING HV CONVEYING |
| Парткод: | 302ND24130 |
| Деталь: | PLATE EARTH SECONDLY TRANSFER |
| Парткод: | 302ND22080 |
| Деталь: | BUSH SECONDLY TRANSFER F |
| Парткод: | 302ND24160 |
| Деталь: | PLATE EARTH SECONDLY TRANSFER B |
| Парткод: | 302ND22110 |
| Деталь: | SPRING-COMPRESSION SECONDLY TRANSFER |
| Парткод: | 302ND24080 |
| Деталь: | ARM PRESS RELEASE F |
| Парткод: | 302ND24020 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | BUSH SECONDLY TRANSFER R |
| Парткод: | 302ND24170 |
| Деталь: | ARM PRESS RELEASE R |
| Парткод: | 302ND24030 |
| Деталь: | HOLDER DISCHARGER |
| Парткод: | 302ND22060 |
| Деталь: | PLATE DISCHARGER |
| Парткод: | 302ND22050 |
| Деталь: | SPRING EARTH CONVEYING |
| Парткод: | 302ND22120 |
| Деталь: | VARISTOR TC ASSY |
| Парткод: | 302FZ01310 |
| Деталь: | CONN.CORD ASSY CONVEYING |
| Парткод: | 302ND46130 |
| Деталь: | CONN.CORD ASSY TRANSFER BELT SENSOR |
| Парткод: | 302ND46620 |
| Деталь: | SEAL DISCHARGER |
| Парткод: | 302KK25140 |
| Деталь: | PARTS RIGHT COVER ASSY SP |
| Парткод: | 302ND94743 |
| Деталь: | WT-8500/WASTE TONER BOTTLE |
| Парткод: | 1902ND0UN0 |
| Деталь: | PARTS DC MOTOR ASSY B SP |
| Парткод: | 302ND94870 |
| Деталь: | PARTS PWB EDGE SENSOR ASSY SP |
| Парткод: | 302K994210 |
| Деталь: | PARTS RETAINER ASSY SP |
| Парткод: | 302V894160 |
| Деталь: | DUCT IMAGE A |
| Парткод: | 302ND33210 |
| Деталь: | PARTS PWB DRUM HEATER ASSY SP |
| Парткод: | 302NK94090 |
| Деталь: | PARTS PWB DRUM DLP CONNECT ASSY SP |
| Парткод: | 302NK94020 |
| Деталь: | PARTS HINGE H MONO ASSY SP |
| Парткод: | 302ND94130 |
| Деталь: | SLIDER CASSETTE LEFT |
| Парткод: | 302ND09521 |
| Деталь: | DUCT IMAGE B |
| Парткод: | 302ND33220 |
| Деталь: | PARTS,FAN IMAGE SP |
| Парткод: | 302FZ94660 |
| Деталь: | SPONGE WIRE |
| Парткод: | 302H719150 |
| Деталь: | GEAR Z19L |
| Парткод: | 302ND03440 |
| Деталь: | GEAR Z25R |
| Парткод: | 302ND03450 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302K994360 |
| Деталь: | CUSHION AIR FAN |
| Парткод: | 302ND39650 |
| Деталь: | PARTS WTB UNIT SP |
| Парткод: | 302ND94224 |
| Деталь: | PARTS FAN COOLING LSU 60 ASSY SP |
| Парткод: | 302L794160 |
| Деталь: | FRAME FEED REGIST |
| Парткод: | 302ND24620 |
| Деталь: | PLATE EARTH MIDDLE |
| Парткод: | 302ND24650 |
| Деталь: | PARTS ROLLER MIDDLE L SP |
| Парткод: | 302ND94410 |
| Деталь: | BUSH METAL REGIST |
| Парткод: | 302HG24200 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | SPRING HV |
| Парткод: | 302ND24660 |
| Деталь: | HOLDER TORQUE LIMITER |
| Парткод: | 302ND24730 |
| Деталь: | TORQUE-LIMITER 400 |
| Парткод: | 303LL07521 |
| Деталь: | STOPPER RETARD |
| Парткод: | 303NG06320 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS CLUTCH 35 Z35R SP |
| Парткод: | 302RH94090 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SPRING PROTECTOR REGIST |
| Парткод: | 302ND24640 |
| Деталь: | MOUNT SENSOR REGIST |
| Парткод: | 302ND24630 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 303NW94040 |
| Деталь: | PLATE CLEANER REGIST |
| Парткод: | 302ND24710 |
| Деталь: | SHEET REGIST F |
| Парткод: | 302ND24670 |
| Деталь: | SHEET REGIST R |
| Парткод: | 302ND24680 |
| Деталь: | CONN.CORD ASSY MID FEED UNIT |
| Парткод: | 302ND46090 |
| Деталь: | PARTS CLEANER REGIST ASSY SP |
| Парткод: | 302ND94020 |
| Деталь: | GEAR Z24L |
| Парткод: | 302K924510 |
| Деталь: | STOPPER 8 |
| Парткод: | 302K921120 |
| Деталь: | HOLDER BEARING MR126ZZ |
| Парткод: | 302K931970 |
| Деталь: | BEARING MR126ZZ |
| Парткод: | 7BE006124431H01 |
| Деталь: | SHAFT CASSETTE FRONT |
| Парткод: | 302ND09540 |
| Деталь: | SHAFT CASSETTE FRONT 1ST |
| Парткод: | 302ND09570 |
| Деталь: | GUIDE CASSETTE SET |
| Парткод: | 302ND09530 |
| Деталь: | PARTS REGIST FEED ASSY SP |
| Парткод: | 302ND94160 |
| Деталь: | PARTS ROLLER REGIST H ASSY SP |
| Парткод: | 302ND94100 |
| Деталь: | PARTS MOTOR-BL W10 ASSY SP |
| Парткод: | 302NK94100 |
| Деталь: | PARTS FAN COOLING DLP 70 SP |
| Парткод: | 302K994350 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302NK94070 |
| Деталь: | GEAR Z23S CONTAINER JOINT |
| Парткод: | 302ND15430 |
| Деталь: | SCREW FAN |
| Парткод: | 302H733430 |
| Деталь: | PIN CONTAINER JOINT |
| Парткод: | 302ND15500 |
| Деталь: | MC-8550 |
| Парткод: | 302ND93171 |
| Деталь: | DK-8550 |
| Парткод: | 302ND93072 |
| Деталь: | PLATE FUSER RELEASE |
| Парткод: | 302ND31450 |
| Деталь: | BUSH SNAP |
| Парткод: | 302ND31910 |
| Деталь: | PARTS DC MOTOR ASSY B SP |
| Парткод: | 302ND94050 |
| Деталь: | GEAR Z17S-Z42S |
| Парткод: | 302ND31470 |
| Деталь: | GEAR Z40L Z14S |
| Парткод: | 302ND31490 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR Z13S-Z43S |
| Парткод: | 302ND31460 |
| Деталь: | GEAR Z35S |
| Парткод: | 302ND31480 |
| Деталь: | SHAFT FUSER RELEASE |
| Парткод: | 302ND31500 |
| Деталь: | GEAR Z20S FUSER RELEASE |
| Парткод: | 302ND31510 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PARTS MOTOR-BL W30 SET SP |
| Парткод: | 302ND94911 |
| Деталь: | CONN.CORD ASSY FUSER MOTOR H |
| Парткод: | 302ND46790 |
| Деталь: | PLATE FUSER DRIVE |
| Парткод: | 302ND31350 |
| Деталь: | RAIL RELEASE |
| Парткод: | 302ND31850 |
| Деталь: | PLATE WORK FUSER |
| Парткод: | 302ND31530 |
| Деталь: | GROUND BASE SCANNER |
| Парткод: | 302 H017380 |
| Деталь: | BUSH 8 |
| Парткод: | 302H024830 |
| Деталь: | SPRING COUPRING RELEASE |
| Парткод: | 302ND31830 |
| Деталь: | COUPLING REST |
| Парткод: | 302ND31550 |
| Деталь: | COUPLING CLAW |
| Парткод: | 302ND31540 |
| Деталь: | LEVER FUSER RELEASE |
| Парткод: | 302ND31370 |
| Деталь: | SPRING LEVER RELEASE |
| Парткод: | 302ND31400 |
| Деталь: | GEAR Z51S JOINT |
| Парткод: | 302ND31320 |
| Деталь: | JOINT FUSER DRIVE |
| Парткод: | 302ND31360 |
| Деталь: | SPRING FUSER |
| Парткод: | 302ND31390 |
| Деталь: | SPRING JOINT |
| Парткод: | 302ND31380 |
| Деталь: | GEAR Z23S FUSER |
| Парткод: | 302ND31310 |
| Деталь: | CUT WASHER 6 12 25 |
| Парткод: | 302H714930 |
| Деталь: | GEAR Z90R Z48S |
| Парткод: | 302ND31340 |
| Деталь: | GEAR Z37S Z68R |
| Парткод: | 302ND31440 |
| Деталь: | GEAR Z42S IDLE |
| Парткод: | 302ND31330 |
| Деталь: | GEAR Z24S EXIT |
| Парткод: | 302ND31420 |
| Деталь: | GEAR Z23S EXIT |
| Парткод: | 302ND31410 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PARTS FUSER DRIVE H ASSY SP |
| Парткод: | 302ND94A30 |
| Деталь: | CONT BOX |
| Парткод: | 302V839010 |
| Деталь: | PARTS PWB KUIO ASSY SP |
| Парткод: | 302K994270 |
| Деталь: | CONN.CORD ASSY FFC MAIN KUIO |
| Парткод: | 302ND46520 |
| Деталь: | RAIL KUIO |
| Парткод: | 302R439070 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390011++H01 |
| Деталь: | CONT BOX SUB |
| Парткод: | 302ND39020 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | DUCT CONTROLLER |
| Парткод: | 302ND33010 |
| Деталь: | FAN BOX COOLING |
| Парткод: | 302FZ44040 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302VK94010 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302VK94020 |
| Деталь: | PARTS PWB ENGINE ASSY SP |
| Парткод: | 302VK94030 |
| Деталь: | CONN.CORD ASSY FFC MAIN ENGINE |
| Парткод: | 302L746100 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390003++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610004++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | CONN.CORD ASSY IMAGE FUSER JOINT |
| Парткод: | 302ND46370 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210013++H01 |
| Деталь: | HOLDER FUSER DRAWER |
| Парткод: | 302ND02290 |
| Деталь: | SHEET FUSER DRAWER |
| Парткод: | 302ND39320 |
| Деталь: | DUCT LVU FAN B |
| Парткод: | 302ND33030 |
| Деталь: | PARTS FAN MOTOR SP |
| Парткод: | 302K094300 |
| Деталь: | DUCT LVU FAN A |
| Парткод: | 302ND33020 |
| Деталь: | PARTS PWB ASSY THERMISTOR SP |
| Парткод: | 302M294130 |
| Деталь: | LID KMAS |
| Парткод: | 2C912430 |
| Деталь: | SEAL SQUARE 25-20 |
| Парткод: | 302HN02720 |
| Деталь: | HINGE CONT BOX |
| Парткод: | 302ND39070 |
| Деталь: | PLATE EARTH CONT BOX |
| Парткод: | 302ND39300 |
| Деталь: | PLATE EARTH ISU |
| Парткод: | 302ND02580 |
| Деталь: | PLATE EARTH |
| Парткод: | 302ND02400 |
| Деталь: | SHEET GUIDE TRANSFER |
| Парткод: | 302ND02481 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SHIELD SCREW |
| Парткод: | 302K903620 |
| Деталь: | PARTS SSD SP |
| Парткод: | 302ND94670 |
| Деталь: | PARTS ID SENSOR ASSY SP |
| Парткод: | 302ND94140 |
| Деталь: | PARTS MOTOR SWITCHBACK SP |
| Парткод: | 302ND94490 |
| Деталь: | ATTACHMENT ACT |
| Парткод: | 302ND28190 |
| Деталь: | COVER MAIN EXIT |
| Парткод: | 302ND28070 |
| Деталь: | ACTUATOR MAIN EXIT FULL A |
| Парткод: | 302ND28150 |
| Деталь: | MOUNT EXIT DRIVE REAR |
| Парткод: | 302ND28250 |
| Деталь: | GEAR Z63S T0.05P |
| Парткод: | 302ND28170 |
| Деталь: | GEAR Z78S T0.2P |
| Парткод: | 302ND28370 |
| Деталь: | SPRING EARTH MAIN EXIT |
| Парткод: | 302ND28401 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 302ND28300 |
| Деталь: | SPRING EARTH REAR C |
| Парткод: | 302ND28100 |
| Деталь: | PARTS SOLENOID FEED SHIFT SP |
| Парткод: | 302K994380 |
| Деталь: | SPRING,STACK BYPASS GEAR |
| Парткод: | 63706260 |
| Деталь: | MOUNT EXIT DRIVE FRONT |
| Парткод: | 302ND28240 |
| Деталь: | LEVER SOLENOID INNER |
| Парткод: | 302ND28220 |
| Деталь: | GEAR Z60R Z23S |
| Парткод: | 302ND28360 |
| Деталь: | PLATE EARTH FRONT |
| Парткод: | 302ND28460 |
| Деталь: | Guide Wire |
| Парткод: | 302ND28310 |
| Деталь: | WIRE SADDLE,RMS-1V0(TAKEUCHI) |
| Парткод: | 7YZM610006++H01 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | COVER SENSOR |
| Парткод: | 302ND28420 |
| Деталь: | CONN.CORD ASSY EXIT |
| Парткод: | 302ND46200 |
| Деталь: | COVER EXIT |
| Парткод: | 302ND28200 |
| Деталь: | COVER INNER EXIT |
| Парткод: | 302ND28210 |
| Деталь: | CUSHION HANDLE A |
| Парткод: | 302GR05080 |
| Деталь: | CUSHION FEED SHIFT GUIDE |
| Парткод: | 303H321070 |
| Деталь: | GUIDE EXIT OVER FLOW |
| Парткод: | 302ND28320 |
| Деталь: | ACTUATOR MAIN EXIT FULL B |
| Парткод: | 302ND28180 |
| Деталь: | ACTUATOR INNER EXIT FULL A |
| Парткод: | 302ND28140 |
| Деталь: | SPRING EARTH REAR B |
| Парткод: | 302ND28380 |
| Деталь: | PARTS EXIT UNIT SP |
| Парткод: | 302ND94082 |
| Деталь: | SLIDER CASSETTE RIGHT |
| Парткод: | 302ND09511 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PULLEY DU |
| Парткод: | 302K329020 |
| Деталь: | MOUNT COVER STRAP |
| Парткод: | 302ND06790 |
| Деталь: | MOUNT FULCRUM |
| Парткод: | 302ND06770 |
| Деталь: | MOUNT FULCRUM R |
| Парткод: | 302ND06800 |
| Деталь: | BUSH DRIVE 6 |
| Парткод: | 302H431070 |
| Деталь: | JOINT SHAFT EW |
| Парткод: | 302ND06680 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | PARTS ROLLER FEED LOW B SP |
| Парткод: | 302ND94370 |
| Деталь: | BUSH DU |
| Парткод: | 302K329270 |
| Деталь: | BUSH DRIVE |
| Парткод: | 302HN31590 |
| Деталь: | MOUNT SENSOR |
| Парткод: | 302ND06761 |
| Деталь: | ACTUATOR FEED LOW |
| Парткод: | 302ND06570 |
| Деталь: | SPRING ACTUATOR PI |
| Парткод: | 302ND06720 |
| Деталь: | MOUNT SENSOR OPT B |
| Парткод: | 302ND06640 |
| Деталь: | CASSETTE BASE 2ND |
| Парткод: | 302ND09024 |
| Деталь: | PLATE PAPER BOTTOM 2ND |
| Парткод: | 302ND09460 |
| Деталь: | CURSOR FRONT |
| Парткод: | 302ND09040 |
| Деталь: | COVER CURSORF |
| Парткод: | 302ND09050 |
| Деталь: | LEVER CURSOR F |
| Парткод: | 302ND09060 |
| Деталь: | SPRING RELEASE CURSOR |
| Парткод: | 302ND09070 |
| Деталь: | RACKCURSORF |
| Парткод: | 302ND09080 |
| Деталь: | PLATE CURSOR REAR |
| Парткод: | 302ND09090 |
| Деталь: | SHAFT DRIVE LIFT |
| Парткод: | 302ND09110 |
| Деталь: | PLATE LIFTUP |
| Парткод: | 302ND09120 |
| Деталь: | LEVER CURSOR SET |
| Парткод: | 302ND09130 |
| Деталь: | CURSOR END |
| Парткод: | 302ND09150 |
| Деталь: | CURSOR END SUB |
| Парткод: | 302ND09160 |
| Деталь: | ARM SIZE DETECTION 2ND |
| Парткод: | 302ND09181 |
| Деталь: | ACTUATOR PAPER LEVEL |
| Парткод: | 302ND09190 |
| Деталь: | LEVER SIDE SWITCH A |
| Парткод: | 302ND09201 |
| Деталь: | LEVER SIDE SWITCH B |
| Парткод: | 302ND09211 |
| Деталь: | SPRING SIDE SWITCH |
| Парткод: | 302ND09220 |
| Деталь: | SPRING EARTH CASSETTE |
| Парткод: | 302ND09230 |
| Деталь: | LEVER CASSETTE SET |
| Парткод: | 302ND09240 |
| Деталь: | SPRING CASSETTE SET |
| Парткод: | 302ND09250 |
| Деталь: | COVER CASSETTE 2ND |
| Парткод: | 302ND09270 |
| Деталь: | SPRING CURSOR RACK |
| Парткод: | 302ND09320 |
| Деталь: | CURSOR END RACK R |
| Парткод: | 302ND09330 |
| Деталь: | CURSOR END RACK L |
| Парткод: | 302ND09340 |
| Деталь: | SPRING SIZE FIX E |
| Парткод: | 302ND09350 |
| Деталь: | PLATE CASSETTE PINION |
| Парткод: | 302ND09370 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 302ND09390 |
| Цена: | 650 ₽ |
| Деталь: | REINFORCEMENT HANDLE |
| Парткод: | 302ND09450 |
| Деталь: | SIZE FIX |
| Парткод: | 302HN09240 |
| Деталь: | STOPPER SIZE SET |
| Парткод: | 302K309350 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302K909261 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09991 |
| Деталь: | SPRING FIX |
| Парткод: | 302HN09190 |
| Деталь: | GEAR GUIDE SIDE |
| Парткод: | 302BM07410 |
| Деталь: | STATIC ELIMINATOR CURSOR |
| Парткод: | 303JY37220 |
| Деталь: | SPRING CURSOR SET |
| Парткод: | 302NT09060 |
| Деталь: | LABEL CASSETTE PAPER MAX |
| Парткод: | 302ND34010 |
| Деталь: | LABEL CASSETTE OPERATION B |
| Парткод: | 302ND34030 |
| Деталь: | LABEL CASSETTE CURSOR OPERATION B |
| Парткод: | 302ND34050 |
| Деталь: | LABEL PAPER SIZE F |
| Парткод: | 302ND34110 |
| Деталь: | LABEL PAPER SIZE G |
| Парткод: | 302ND34340 |
| Деталь: | LABEL PAPER SIZE A |
| Парткод: | 302ND34060 |
| Деталь: | LABEL PAPER SIZE D |
| Парткод: | 302ND34090 |
| Деталь: | LABEL PAPER SIZE C |
| Парткод: | 302ND34080 |
| Деталь: | GUIDE PAPER SET SUB |
| Парткод: | 302ND09380 |
| Деталь: | PARTS REINFORCEMENT CASSETTE SET SP |
| Парткод: | 302ND94A00 |
| Деталь: | CT-8560 |
| Парткод: | 302ND93022 |
| Деталь: | FRAME EXIT |
| Парткод: | 302ND28010 |
| Деталь: | CUSHION GUIDE |
| Парткод: | 302ND28120 |
| Деталь: | CUSHION EJECT GUIDE |
| Парткод: | 303H321050 |
| Деталь: | PULLEY GUIDE |
| Парткод: | 302ND28030 |
| Деталь: | SPRING HOLDER PULLEY C |
| Парткод: | 302ND28641 |
| Деталь: | SHAFT PULLEY |
| Парткод: | 303RG24110 |
| Деталь: | PULLY EXIT |
| Парткод: | 302ND28580 |
| Деталь: | SPRING PULLEY |
| Парткод: | 302F928170 |
| Деталь: | CAP SPRING |
| Парткод: | 302ND24290 |
| Деталь: | CAP HOLDER SHAFT |
| Парткод: | 302ND29630 |
| Деталь: | GUIDE CHANGE LOWER |
| Парткод: | 302ND28061 |
| Деталь: | GUIDE CHANGE SWITCHBACK |
| Парткод: | 302ND28091 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302ND08670 |
| Деталь: | BUSH SLIDE EW |
| Парткод: | 302ND28450 |
| Деталь: | GUIDE MAIN EXIT UPPER |
| Парткод: | 302ND28050 |
| Деталь: | STATIC-ELIMINATOR EXIT |
| Парткод: | 302ND28410 |
| Деталь: | PARTS ROLLER MAIN EXIT SP |
| Парткод: | 302ND94420 |
| Деталь: | PARTS ROLLER FEED EXIT SP |
| Парткод: | 302ND94440 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | GEAR Z27S |
| Парткод: | 302ND28340 |
| Деталь: | GEAR Z27S ONEWAY |
| Парткод: | 302ND28290 |
| Деталь: | SPRING GUIDE PUSH JS C |
| Парткод: | 302ND28530 |
| Деталь: | SPRING GUIDE PUSH JS FR |
| Парткод: | 302ND28540 |
| Деталь: | SPRING GUIDE PUSH |
| Парткод: | 302ND28500 |
| Деталь: | HOLDER GUIDE PUSH |
| Парткод: | 302ND28470 |
| Деталь: | GUIDE EXIT PUSH JS |
| Парткод: | 302NL28010 |
| Деталь: | GUIDE INNER EXIT UPPER |
| Парткод: | 302ND28080 |
| Деталь: | SPRING GUIDE PUSH MAIN |
| Парткод: | 302ND28590 |
| Деталь: | PLATE EARTH INNER EXIT |
| Парткод: | 302ND28390 |
| Деталь: | PARTS ROLLER SWITCHBACK SP |
| Парткод: | 302ND94430 |
| Деталь: | GEAR Z23S |
| Парткод: | 302ND28260 |
| Деталь: | ACTUATOR SWITCHBACK |
| Парткод: | 302ND28330 |
| Деталь: | PULLEY EXIT |
| Парткод: | 302V828010 |
| Деталь: | GUIDE MAIN EXIT LOWER |
| Парткод: | 302ND28040 |
| Деталь: | GUIDE RIGHT EXIT |
| Парткод: | 302ND28280 |
| Деталь: | CAP SPRING |
| Парткод: | 302K925360 |
| Деталь: | SPRING LEVER DLP |
| Парткод: | 302F914560 |
| Деталь: | SPRING-TORSION SWITCHBACK |
| Парткод: | 302K928190 |
| Деталь: | COVER RIGHT EXIT |
| Парткод: | 302ND28430 |
| Деталь: | LABEL CAUTION |
| Парткод: | 302ND34320 |
| Деталь: | LABEL A1 |
| Парткод: | 302ND34250 |
| Деталь: | GUIDE INNER EXIT LOWER B |
| Парткод: | 302ND28610 |
| Деталь: | GUIDE EXIT PUSH F10 T3 S1 |
| Парткод: | 302ND28490 |
| Деталь: | STATIC-ELIMINATOR EJECT |
| Парткод: | 303NB36460 |
| Деталь: | STATIC-ELIMINATOR EJECT |
| Парткод: | 303N816340 |
| Деталь: | TAPE EARTH |
| Парткод: | 302ND28600 |
| Деталь: | CUSHION EJECT GUIDE |
| Парткод: | 302ND28650 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | PLATE EARTH FRONT MAIN |
| Парткод: | 302ND28660 |
| Деталь: | BUSH SLIDE |
| Парткод: | 302ND28270 |
| Деталь: | PARTS EXIT UNIT SP |
| Парткод: | 302ND94082 |
| Деталь: | COVER LEFT |
| Парткод: | 302ND04060 |
| Деталь: | COVER LEFT REAR |
| Парткод: | 302ND04180 |
| Деталь: | COVER LEFT B |
| Парткод: | 302ND04310 |
| Деталь: | COVER LEFT LID |
| Парткод: | 302ND04240 |
| Деталь: | FILTER TRANSFER |
| Парткод: | 302ND33240 |
| Деталь: | COVER LEFT UP |
| Парткод: | 302ND04070 |
| Деталь: | COVER ISU RIGHT |
| Парткод: | 302ND04130 |
| Деталь: | COVER RIGHT FRONT |
| Парткод: | 302ND04230 |
| Деталь: | Cover Handle |
| Парткод: | 302ND04691 |
| Деталь: | Cover Right Rear |
| Парткод: | 302V804020 |
| Деталь: | SPRING SLIDER |
| Парткод: | 302ND04380 |
| Деталь: | SLIDER COVER |
| Парткод: | 302ND04300 |
| Деталь: | COVER FILTER EXIT |
| Парткод: | 302ND04980 |
| Деталь: | FILTER REAR LOWER |
| Парткод: | 302ND33260 |
| Деталь: | COVER RIGHT REAR UPPER |
| Парткод: | 302V804010 |
| Деталь: | LID SD-CARD |
| Парткод: | 302ND04470 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302V804050 |
| Деталь: | LID DP |
| Парткод: | 302RH04330 |
| Деталь: | COVER MAIN SWITCH |
| Парткод: | 302V804060 |
| Деталь: | NUT FUSER |
| Парткод: | 302K926050 |
| Деталь: | COVER FRONT RIGHT |
| Парткод: | 302V804590 |
| Деталь: | COVER KEYBOARD |
| Парткод: | 302ND04700 |
| Деталь: | COVER WASTE |
| Парткод: | 302ND04151 |
| Деталь: | LID CARD-READER RIGHT |
| Парткод: | 302ND04710 |
| Деталь: | COVER FRONT UPPER |
| Парткод: | 302ND04741 |
| Деталь: | PLATE MAGNET |
| Парткод: | 302NL04270 |
| Деталь: | EMBLEM KC 1SG 70 B |
| Парткод: | 302DY04011 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | COVER FRONT |
| Парткод: | 302ND04010 |
| Деталь: | SPACER USB |
| Парткод: | 302LW04260 |
| Деталь: | STRAP FRONT COVER |
| Парткод: | 302ND04570 |
| Деталь: | CUT-WASHER 6 |
| Парткод: | 302K921420 |
| Деталь: | COVER RIGHT SIDE |
| Парткод: | 302ND04660 |
| Деталь: | COVER REAR UPPER |
| Парткод: | 302ND04080 |
| Деталь: | PLATE SHIELD |
| Парткод: | 302ND04340 |
| Деталь: | COVER REAR LOWER |
| Парткод: | 302ND04090 |
| Деталь: | CUSHION COVER LEFT |
| Парткод: | 302ND04A40 |
| Деталь: | LABEL SW CAUTION JP |
| Парткод: | 302ND34210 |
| Деталь: | LABEL SW CAUTION EN |
| Парткод: | 302V834030 |
| Деталь: | LABEL MPF SIZE INDICATOR ME |
| Парткод: | 302ND08720 |
| Деталь: | LABEL MPF SIZE INDICATOR IN |
| Парткод: | 302ND08710 |
| Деталь: | SHEET OPERATION TONER A |
| Парткод: | 302ND34300 |
| Деталь: | SHEET OPERATION TONER B |
| Парткод: | 302ND34310 |
| Деталь: | LABEL EMBLEM 4003 |
| Парткод: | 302W934010 |
| Деталь: | LABEL EMBLEM 5003 |
| Парткод: | 302VL34010 |
| Деталь: | LABEL EMBLEM 6003 |
| Парткод: | 302VK34010 |
| Деталь: | COVER CASSETTE LABEL 1 |
| Парткод: | 302ND09420 |
| Деталь: | COVER CASSETTE LABEL 2 |
| Парткод: | 302ND09430 |
| Деталь: | LABEL SW CAUTION US |
| Парткод: | 302ND34470 |
| Деталь: | MOUNT ISU A2 |
| Парткод: | 302ND17180 |
| Деталь: | MOUNT ISU D4 |
| Парткод: | 302ND17200 |
| Деталь: | MOUNT ISU E |
| Парткод: | 302ND17310 |
| Деталь: | PULLEY LEFT FRAME |
| Парткод: | 302H017120 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302ND17060 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | MOUNT DP |
| Парткод: | 302ND17010 |
| Деталь: | GUIDE FFC A |
| Парткод: | 302ND17230 |
| Деталь: | GUIDE FFC |
| Парткод: | 302ND17130 |
| Деталь: | PARTS FFC ENGINE CCD SET SP |
| Парткод: | 302ND94950 |
| Деталь: | LABEL CAUTION |
| Парткод: | 302ND34200 |
| Деталь: | FILM FFC CCD |
| Парткод: | 302ND17380 |
| Деталь: | PARTS ISU ASSY SP |
| Парткод: | 302V893010 |
| Деталь: | WIRE SCANNER BLACK |
| Парткод: | 302V817010 |
| Деталь: | WIRE SCANNER GRAY |
| Парткод: | 302V817020 |
| Деталь: | BEARING 686ZZ |
| Парткод: | 7BE006135442H01 |
| Деталь: | GEAR P59 |
| Парткод: | 302ND17160 |
| Деталь: | FRAME MIRROR B |
| Парткод: | 302K317111 |
| Деталь: | PARTS MIRROR B SP |
| Парткод: | 302KK94730 |
| Деталь: | SPRING,MIRROR HOLDER |
| Парткод: | 2BC12190 |
| Деталь: | PLATE ADJUST B |
| Парткод: | 302K317830 |
| Деталь: | GUIDE FFC LED B |
| Парткод: | 302K317160 |
| Деталь: | SLIDER SCANNER |
| Парткод: | 2DC12230 |
| Деталь: | SPRING SCANNER TENSION |
| Парткод: | 302ND17420 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 302ND94800 |
| Деталь: | PARTS MIRROR A SP |
| Парткод: | 302KK94720 |
| Деталь: | PARTS MOUNT LED ASSY SP |
| Парткод: | 302V693080 |
| Деталь: | GUIDE FFC LED |
| Парткод: | 302V617080 |
| Деталь: | SHEET LED FFC |
| Парткод: | 302ND17430 |
| Деталь: | COVER LENS |
| Парткод: | 302MV17030 |
| Деталь: | HOLDER BEARING |
| Парткод: | 302ND17330 |
| Деталь: | SPONGE HOUSING FAN A |
| Парткод: | 302ND33280 |
| Деталь: | PARTS DUCT IH COIL FAN A ASSY SP |
| Парткод: | 302ND94890 |
| Деталь: | PARTS FAN CENTER 60 25 SP |
| Парткод: | 302ND94590 |
| Деталь: | PARTS PWB TRANSFER CONNECT ASSY SP |
| Парткод: | 302ND94290 |
| Деталь: | PARTS HOUSING FAN IH COIL H ASSY SP |
| Парткод: | 302ND94880 |
| Деталь: | PARTS UNIT HIGH VOLTAGE FUSER SP |
| Парткод: | 302ND94690 |
| Деталь: | PARTS TONER HOPPER MONO UNIT SP |
| Парткод: | 302NK94032 |
| Деталь: | COVER WIRE EJECT |
| Парткод: | 302ND39310 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | SEAL DUCT IH F B |
| Парткод: | 302ND33390 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302LC94380 |
| Деталь: | PARTS CONTAINER RAIL MONO ASSY SP |
| Парткод: | 302NK94140 |
| Деталь: | COVER TRAY BASE |
| Парткод: | 302ND04672 |
| Деталь: | COVER TOP REAR |
| Парткод: | 302V804040 |
| Деталь: | TRAY INNER UPPER |
| Парткод: | 302ND04250 |
| Деталь: | ACTUATOR TRAY INNER |
| Парткод: | 302ND04271 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 302ND04421 |
| Деталь: | COVER ACTUATOR |
| Парткод: | 302ND04350 |
| Деталь: | SHAFT TRAY |
| Парткод: | 302ND04261 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STOPPER PAPER OUTER |
| Парткод: | 302ND04280 |
| Деталь: | STOPPER PAPER INNER |
| Парткод: | 302ND04290 |
| Деталь: | COVER INNER |
| Парткод: | 302ND04730 |
| Деталь: | COVER INNER FRONT UP |
| Парткод: | 302V804070 |
| Деталь: | COVER TRAY TOP |
| Парткод: | 302ND04101 |
| Деталь: | STOPPER PAPER INNER |
| Парткод: | 302ND04961 |
| Деталь: | COVER RIGHT LOWER |
| Парткод: | 302ND04430 |
| Деталь: | PLATE COVER LOWER |
| Парткод: | 302ND04560 |
| Деталь: | COVER DP |
| Парткод: | 302ND04720 |
| Деталь: | COVER DP B |
| Парткод: | 302ND04610 |
| Деталь: | COVER FILTER |
| Парткод: | 302ND04940 |
| Деталь: | FILTER TOP |
| Парткод: | 302ND33250 |
| Деталь: | COVER INNER MONO |
| Парткод: | 302NK04010 |
| Деталь: | SHEET DUCT PU |
| Парткод: | 302ND04440 |
| Деталь: | SEAL DUCT PU |
| Парткод: | 302ND04450 |
| Деталь: | SPACER USB |
| Парткод: | 302LW04260 |
| Деталь: | SPRING COVER LOCK |
| Парткод: | 302ND04480 |
| Деталь: | LUTCH |
| Парткод: | 302HN08140 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302H004660 |
| Деталь: | LEVER SWITCH |
| Парткод: | 302ND04330 |
| Деталь: | SPRING LEVER SWITCH |
| Парткод: | 302ND04390 |
| Деталь: | RETAINER M4 |
| Парткод: | 3CY06030 |
| Деталь: | COVER OUTER CONTAINER |
| Парткод: | 302ND04820 |
| Деталь: | TRAY INNER SUB |
| Парткод: | 302ND28560 |
| Деталь: | LABEL OPERATION TONER JP |
| Парткод: | 302ND34410 |
| Деталь: | LABEL OPERATION TONER ENG |
| Парткод: | 302ND34420 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302ND04A60 |
| Деталь: | SPRING ACTUATOR TRAY |
| Парткод: | 302ND04A90 |
| Деталь: | PLATE SUPPORT STOPPER PAPER |
| Парткод: | 302ND04A70 |
| Деталь: | TRAY SUB ENVELOPE |
| Парткод: | 302ND04580 |
| Деталь: | PARTS MOTOR-BL W30 DRUM ASSY SP |
| Парткод: | 302ND94552 |
| Деталь: | PARTS MOTOR-BL W20 DRUM Z11 ASSY SP |
| Парткод: | 302ND94532 |
| Деталь: | PARTS PWB FEED IMAGE ASSY SP |
| Парткод: | 302VK94040 |
| Деталь: | PARTS BOX WASTE MONO ASSY SP |
| Парткод: | 302NK94015 |
| Деталь: | DR-6510 |
| Парткод: | 302VK93011 |
| Деталь: | RAIL SECONDLY TRANSFER F |
| Парткод: | 302ND24410 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM590001++H01 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302P794010 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | SPRING IH |
| Парткод: | 302ND26040 |
| Деталь: | CAP SPRING |
| Парткод: | 302LK26050 |
| Деталь: | HANDLE |
| Парткод: | 302JF02160 |
| Деталь: | SEAL HANDLE |
| Парткод: | 302FZ03110 |
| Деталь: | CAP HANDLE |
| Парткод: | 302FZ02580 |
| Деталь: | STOPPER 4 |
| Парткод: | 302FZ25740 |
| Деталь: | LEVER SIZE B |
| Парткод: | 302ND09300 |
| Деталь: | LEVER SIZE A |
| Парткод: | 302ND09290 |
| Деталь: | HOLDER SIDE SWITCH |
| Парткод: | 302ND09280 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP03090001+H01 |
| Деталь: | LEVER SIZE C |
| Парткод: | 302ND09310 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000007+H01 |
| Деталь: | MOUNT PAPER SENSOR |
| Парткод: | 302ND09360 |
| Деталь: | MOUNT PF PIN |
| Парткод: | 302ND02490 |
| Деталь: | HOLDER HEATER CONNECTOR |
| Парткод: | 302ND02531 |
| Деталь: | PARTS MOTOR LIFT ASSY SP |
| Парткод: | 302ND94481 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | CAP DECK PIN |
| Парткод: | 302ND39110 |
| Деталь: | PIN DRIVE MIDDLE |
| Парткод: | 302ND06590 |
| Деталь: | GEAR Z29L-Z27L |
| Парткод: | 302ND06610 |
| Деталь: | PLATE COVER HEATER |
| Парткод: | 302ND02540 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | MOUNT ISU C |
| Парткод: | 302ND17190 |
| Деталь: | MOUNT ISU F |
| Парткод: | 302ND17290 |
| Деталь: | RAIL SECONDLY TRANSFER R |
| Парткод: | 302ND24420 |
| Деталь: | PLATE DAMPER C |
| Парткод: | 302ND29490 |
| Деталь: | FULCRUM-PIN FEED |
| Парткод: | 302ND04630 |
| Деталь: | STOPPER GUIDE PAPER |
| Парткод: | 302ND02790 |
| Деталь: | CASSETTE BASE 1ST |
| Парткод: | 302ND09013 |
| Деталь: | PLATE PAPER BOTTOM |
| Парткод: | 302ND09030 |
| Деталь: | CURSOR FRONT |
| Парткод: | 302ND09040 |
| Деталь: | COVER CURSORF |
| Парткод: | 302ND09050 |
| Деталь: | LEVER CURSOR F |
| Парткод: | 302ND09060 |
| Деталь: | SPRING RELEASE CURSOR |
| Парткод: | 302ND09070 |
| Деталь: | RACKCURSORF |
| Парткод: | 302ND09080 |
| Деталь: | PLATE CURSOR REAR |
| Парткод: | 302ND09090 |
| Деталь: | SHAFT DRIVE LIFT |
| Парткод: | 302ND09110 |
| Деталь: | PLATE LIFTUP |
| Парткод: | 302ND09120 |
| Деталь: | LEVER CURSOR SET |
| Парткод: | 302ND09130 |
| Деталь: | CURSOR END |
| Парткод: | 302ND09150 |
| Деталь: | CURSOR END SUB |
| Парткод: | 302ND09160 |
| Деталь: | ARM SIZE DETECTION 1ST |
| Парткод: | 302ND09171 |
| Деталь: | ACTUATOR PAPER LEVEL |
| Парткод: | 302ND09190 |
| Деталь: | LEVER SIDE SWITCH A |
| Парткод: | 302ND09201 |
| Деталь: | LEVER SIDE SWITCH B |
| Парткод: | 302ND09211 |
| Деталь: | SPRING SIDE SWITCH |
| Парткод: | 302ND09220 |
| Деталь: | SPRING EARTH CASSETTE |
| Парткод: | 302ND09230 |
| Деталь: | LEVER CASSETTE SET |
| Парткод: | 302ND09240 |
| Деталь: | SPRING CASSETTE SET |
| Парткод: | 302ND09250 |
| Деталь: | COVER CASSETTE 1ST |
| Парткод: | 302ND09260 |
| Деталь: | SPRING CURSOR RACK |
| Парткод: | 302ND09320 |
| Деталь: | CURSOR END RACK R |
| Парткод: | 302ND09330 |
| Деталь: | CURSOR END RACK L |
| Парткод: | 302ND09340 |
| Деталь: | SPRING SIZE FIX E |
| Парткод: | 302ND09350 |
| Деталь: | PLATE CASSETTE PINION |
| Парткод: | 302ND09370 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 302ND09390 |
| Цена: | 650 ₽ |
| Деталь: | REINFORCEMENT HANDLE |
| Парткод: | 302ND09450 |
| Деталь: | SIZE FIX |
| Парткод: | 302HN09240 |
| Деталь: | STOPPER SIZE SET |
| Парткод: | 302K309350 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302K909261 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09991 |
| Деталь: | SPRING FIX |
| Парткод: | 302HN09190 |
| Деталь: | GEAR GUIDE SIDE |
| Парткод: | 302BM07410 |
| Деталь: | STATIC ELIMINATOR CURSOR |
| Парткод: | 303JY37220 |
| Деталь: | SPRING CURSOR SET |
| Парткод: | 302NT09060 |
| Деталь: | LABEL CASSETTE PAPER MAX |
| Парткод: | 302ND34010 |
| Деталь: | LABEL CASSETTE OPERATION A |
| Парткод: | 302ND34020 |
| Деталь: | LABEL CASSETTE CURSOR OPERATION A |
| Парткод: | 302ND34040 |
| Деталь: | LABEL PAPER SIZE E |
| Парткод: | 302ND34100 |
| Деталь: | LABEL PAPER SIZE B |
| Парткод: | 302ND34070 |
| Деталь: | LABEL PAPER SIZE A |
| Парткод: | 302ND34060 |
| Деталь: | GUIDE ENVELOPE |
| Парткод: | 302ND09470 |
| Деталь: | ARM ENVELOPE |
| Парткод: | 302ND09480 |
| Деталь: | CT-8550 |
| Парткод: | 302ND93012 |
| Деталь: | GUIDE DU RIGHT |
| Парткод: | 302ND29021 |
| Деталь: | SHEET GUIDE DU |
| Парткод: | 302ND29720 |
| Деталь: | SHAFT FEED |
| Парткод: | 302ND29280 |
| Деталь: | PULLEY FEED 16 |
| Парткод: | 302ND29260 |
| Деталь: | SPRING-COMPRESSION PULLEY FEED |
| Парткод: | 302ND29300 |
| Деталь: | CAP SPRING |
| Парткод: | 302ND24290 |
| Деталь: | CAP HOLDER SHAFT |
| Парткод: | 302ND29630 |
| Деталь: | GUIDE DU UPPER LEFT |
| Парткод: | 302ND29040 |
| Деталь: | HOLDER PULLEY DU |
| Парткод: | 302ND29390 |
| Деталь: | LABEL A4 |
| Парткод: | 302ND34280 |
| Деталь: | RING STOPPER 4 |
| Парткод: | 5MVL177DN001 |
| Деталь: | PARTS ROLLER DU UP SP |
| Парткод: | 302ND94450 |
| Деталь: | PLATE EARTH DU UPPER |
| Парткод: | 302ND29450 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | PULLEY P18-S2M |
| Парткод: | 302LF28342 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BUSH DU |
| Парткод: | 302K329270 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | HOLDER SHAFT OUT |
| Парткод: | 302FZ07540 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302ND08670 |
| Деталь: | PARTS ROLLER DU MIDDLE SP |
| Парткод: | 302ND94460 |
| Деталь: | BUSH CONTACT MPT B |
| Парткод: | 302FZ07310 |
| Деталь: | PULLEY P26-S2M |
| Парткод: | 302ND29330 |
| Деталь: | BELT S2M-Z123 |
| Парткод: | 302ND29130 |
| Деталь: | PULLEY FEED PF |
| Парткод: | 303NJ06070 |
| Деталь: | SHAFT GUIDE BELT |
| Парткод: | 302ND29360 |
| Деталь: | PLATE BELT PULLEY |
| Парткод: | 302ND29370 |
| Деталь: | COLLAR DU PULLEY |
| Парткод: | 302FZ29140 |
| Деталь: | PULLEY P26-S2M Z23R |
| Парткод: | 302ND29230 |
| Деталь: | BELT S2M-Z234 |
| Парткод: | 302ND29120 |
| Деталь: | BUSHING 6 |
| Парткод: | 3CY07080 |
| Деталь: | PLATE EARTH CONVEYING |
| Парткод: | 302ND29470 |
| Деталь: | PLATE EARTH DU |
| Парткод: | 302ND29460 |
| Деталь: | BUSH 6 |
| Парткод: | 303P031160 |
| Деталь: | BELT S2M-Z137 |
| Парткод: | 302ND29110 |
| Деталь: | WIRE EARTH DU |
| Парткод: | 302ND29440 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PLATE DU BASE |
| Парткод: | 302ND29580 |
| Деталь: | PLATE REINFORCEMENT REAR |
| Парткод: | 302ND29650 |
| Деталь: | SPRING WIRE MPF |
| Парткод: | 302ND08900 |
| Деталь: | CONN.CORD ASSY RIGHT COVER |
| Парткод: | 302ND46120 |
| Деталь: | PARTS ROLLER DU REGIST SP |
| Парткод: | 302ND94A40 |
| Деталь: | FILM DU REGIST ROLLER |
| Парткод: | 302ND29770 |
| Деталь: | PARTS RIGHT COVER ASSY SP |
| Парткод: | 302ND94743 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | BUSH DRIVE POM |
| Парткод: | 302LV31480 |
| Деталь: | PIN FEED |
| Парткод: | 302ND31700 |
| Деталь: | PIN REGIST |
| Парткод: | 302ND31730 |
| Деталь: | PIN FEED B |
| Парткод: | 302ND31900 |
| Деталь: | PIN DRUM DRIVE |
| Парткод: | 302ND31270 |
| Деталь: | SHAFT JOINT MID |
| Парткод: | 302ND31711 |
| Деталь: | GEAR Z26R |
| Парткод: | 302ND31620 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SHAFT JOINT DU |
| Парткод: | 302ND31721 |
| Деталь: | GEAR Z23R |
| Парткод: | 302ND31630 |
| Деталь: | SHAFT FEED |
| Парткод: | 302ND31740 |
| Деталь: | GEAR Z47L |
| Парткод: | 302ND31590 |
| Деталь: | SHAFT CLUTCH FEED |
| Парткод: | 302ND31690 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302HG12310 |
| Деталь: | PARTS CLUTCH 35 Z35R SP |
| Парткод: | 302RH94090 |
| Деталь: | GEAR Z35R |
| Парткод: | 302K931510 |
| Деталь: | GEAR Z35L |
| Парткод: | 302HN31200 |
| Деталь: | SHAFT FEED OW |
| Парткод: | 302ND31680 |
| Деталь: | PARTS ONE WAY CLUTCH ASSY SP |
| Парткод: | 302ND94570 |
| Деталь: | GEAR Z27L |
| Парткод: | 302K931550 |
| Деталь: | GEAR MIDDLE CLN Z30R |
| Парткод: | 302K031310 |
| Деталь: | GEAR Z56R-Z31R |
| Парткод: | 302ND31780 |
| Деталь: | GEAR Z71R-Z29L-Z42S |
| Парткод: | 302ND31580 |
| Деталь: | GEAR Z16R-Z33S |
| Парткод: | 302ND31660 |
| Деталь: | GEAR Z27L MAIN |
| Парткод: | 302JZ31170 |
| Деталь: | GEAR Z30R IDLE |
| Парткод: | 302K331140 |
| Деталь: | GEAR Z36L MAIN |
| Парткод: | 302H731500 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 302ND31760 |
| Деталь: | PLATE FEED DRIVE |
| Парткод: | 302ND31570 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | GEAR Z16S-Z24R |
| Парткод: | 302ND31670 |
| Цена: | 90 ₽ |
| Деталь: | PIN HINGE GEAR |
| Парткод: | 302ND03700 |
| Деталь: | PARTS MOTOR-BL W30 ASSY SP |
| Парткод: | 302ND94771 |
| Деталь: | BUSH SLIDE |
| Парткод: | 302ND28270 |
| Деталь: | GEAR Z24R |
| Парткод: | 302ND31600 |
| Деталь: | GEAR Z31R |
| Парткод: | 302ND31640 |
| Деталь: | SPRING FEED |
| Парткод: | 302HN31410 |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | 302HN31660 |
| Деталь: | PLATE EARTH FEED A |
| Парткод: | 302ND31790 |
| Деталь: | GUIDE FEED |
| Парткод: | 302ND31770 |
| Деталь: | CONN.CORD ASSY FEED CLUTCH |
| Парткод: | 302ND46060 |
| Деталь: | CONN.CORD ASSY FEED MOTOR |
| Парткод: | 302ND46160 |
| Деталь: | PARTS PWB FEED DRIVE ASSY SP |
| Парткод: | 302ND94280 |
| Деталь: | POLY SLIDER WASHER 6.2X9.5X0.4T |
| Парткод: | 7BC060629540H01 |
| Деталь: | PARTS FEED DRIVE L ASSY SP |
| Парткод: | 302L794041 |
| Деталь: | FK-8550 |
| Парткод: | 302ND93085 |
| Деталь: | FK-8560 |
| Парткод: | 302ND93194 |
| Деталь: | PARTS BELT CHARGER ASSY SP |
| Парткод: | 302ND94810 |
| Деталь: | FK-8595IH |
| Парткод: | 302ND93090 |
| Деталь: | FK-8590IH |
| Парткод: | 302ND93100 |
| Деталь: | DV-8560K |
| Парткод: | 302V893020 |
| Деталь: | DV-8560K(J) |
| Парткод: | 302V89J020 |
| Деталь: | LK-6500 |
| Парткод: | 302NK93010 |
| Деталь: | SPRING REGIST R |
| Парткод: | 302H024331 |
| Деталь: | PIN LSU |
| Парткод: | 302JF19011 |
| Деталь: | CORE 7-15X18 |
| Парткод: | 33927590 |
| Деталь: | FRAME FEED UPPER |
| Парткод: | 302ND06010 |
| Деталь: | SHAFT PRIMARY FEED |
| Парткод: | 302ND06030 |
| Деталь: | PIN PICK UP IDLE |
| Парткод: | 302K906080 |
| Деталь: | HOLDER PICKUP |
| Парткод: | 302ND06020 |
| Деталь: | GEAR Z30 FEED OW |
| Парткод: | 302ND06040 |
| Деталь: | ONEWAY-CLUTCH 6 |
| Парткод: | 302N406120 |
| Деталь: | PULLEY FEED |
| Парткод: | 302N406030 |
| Цена: | 440 ₽ |
| Деталь: | PARTS PULLEY PICKUP SP |
| Парткод: | 302ND94340 |
| Цена: | 650 ₽ |
| Деталь: | PARTS ROLLER RETARD ASSY SP |
| Парткод: | 302ND94351 |
| Цена: | 950 ₽ |
| Деталь: | SHAFT PICKUP PRIMARY |
| Парткод: | 302N406070 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | BUSHING 6,REGISTRATION |
| Парткод: | 2BC06520 |
| Деталь: | GEAR Z32 FEED |
| Парткод: | 302ND06060 |
| Деталь: | GUIDE PRIMARY FEED SUB |
| Парткод: | 302ND06240 |
| Деталь: | SPRING PICKUP RELEASE |
| Парткод: | 302ND06100 |
| Деталь: | LEVER PICKUP RELEASE |
| Парткод: | 302ND06090 |
| Деталь: | LEVER FEED LOCK |
| Парткод: | 302ND06220 |
| Деталь: | SPRING FEED LOCK |
| Парткод: | 302ND06230 |
| Деталь: | LEVER RETARD |
| Парткод: | 302ND06160 |
| Деталь: | SPRING RETARD |
| Парткод: | 302ND06150 |
| Деталь: | LEVER RETARD RELEASE |
| Парткод: | 302ND06181 |
| Деталь: | SPRING RETARD RELEASE |
| Парткод: | 302ND06191 |
| Деталь: | SHAFT RETARD |
| Парткод: | 302ND06140 |
| Деталь: | HOLDER RETARD |
| Парткод: | 302ND06130 |
| Деталь: | GEAR Z24 PICKUP |
| Парткод: | 302ND06050 |
| Деталь: | PLATE RETARD ADJUST |
| Парткод: | 302ND06170 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302ND06070 |
| Деталь: | SPRING PICKUP |
| Парткод: | 302ND06080 |
| Деталь: | GUIDE PRIMARY FEED B |
| Парткод: | 302ND06530 |
| Деталь: | FILM FEED LOW B |
| Парткод: | 302ND06780 |
| Деталь: | LABEL A3 |
| Парткод: | 302ND34270 |
| Деталь: | GUIDE PRIMARY FEED A |
| Парткод: | 302ND06520 |
| Деталь: | FILM FEED LOW |
| Парткод: | 302ND06660 |
| Деталь: | PARTS PRIMARY FEED ASSY SP |
| Парткод: | 302ND94212 |
| Деталь: | PARTS PULLEY SET SP |
| Парткод: | 302ND94701 |
| Деталь: | PARTS DC MOTOR ASSY A SP |
| Парткод: | 302ND94040 |
| Деталь: | PLATE LIFT MPF |
| Парткод: | 302ND08600 |
| Деталь: | RACK LIFT MPF |
| Парткод: | 302ND08630 |
| Деталь: | CASE LIFT MPF |
| Парткод: | 302ND08610 |
| Деталь: | GEAR Z46S-Z18S |
| Парткод: | 302ND08650 |
| Деталь: | WORM-WHEEL 36 Z18S |
| Парткод: | 302ND08640 |
| Деталь: | GEAR LIFT Z35S-Z64S |
| Парткод: | 302ND08620 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000007+H01 |
| Деталь: | ARM INTERLOCK COVER RIGHT |
| Парткод: | 302ND29621 |
| Деталь: | SHEET DAMPER A |
| Парткод: | 302ND29710 |
| Деталь: | MOUNT DAMPER B |
| Парткод: | 302ND29410 |
| Деталь: | MOUNT DAMPER A |
| Парткод: | 302ND29400 |
| Деталь: | SLIDER DAMPER |
| Парткод: | 302ND29670 |
| Деталь: | SPRING-EXTENSION DAMPER B |
| Парткод: | 302ND29660 |
| Деталь: | PIN COVER DAMPER |
| Парткод: | 302ND29420 |
| Деталь: | STOPPER 3 |
| Парткод: | 302LF12410 |
| Деталь: | SPRING-EXTENSION DAMPER |
| Парткод: | 302ND29430 |
| Деталь: | SHAFT FEED |
| Парткод: | 302ND29280 |
| Деталь: | PULLEY FEED 16 |
| Парткод: | 302ND29260 |
| Деталь: | SPRING-COMPRESSION PULLEY FEED |
| Парткод: | 302ND29300 |
| Деталь: | SPRING-COMPRESSION PULLEY MIDDLE |
| Парткод: | 302ND29690 |
| Деталь: | CAP SPRING |
| Парткод: | 302ND24290 |
| Деталь: | CAP HOLDER SHAFT |
| Парткод: | 302ND29630 |
| Деталь: | SHEET GUIDE FEED |
| Парткод: | 302ND29310 |
| Деталь: | CUSHION HANDLE A |
| Парткод: | 302GR05080 |
| Деталь: | GUIDE MIDDLE RIGHT |
| Парткод: | 302ND29030 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | COVER DU WIRE |
| Парткод: | 302ND29340 |
| Деталь: | PARTS RIGHT COVER ASSY SP |
| Парткод: | 302ND94743 |
Коды ошибок
C0030
C0070
C0100
C0120
C0130
C0150
C0160
C0170
C0180
C0350
C0361
C0362
C0640
C0650
C0660
C0670
C0680
C0800
C0830
C0840
C0850
C0870
C0920
C0950
C0980
C1000
C1010
C1020
C1030
C1040
C1140
C1750
C1800
C1820
C1900
C1920
C1950
C2201
C2300
C2500
C2600
C2700
C2760
C2810
C2840
C3100
C3200
C3210
C3300
C3310
C3500
C3600
C3800
C4001
C4011
C4101
C4201
C4600
C4701
C4702
C4801
C5101
C5130
C6000
C6020
C6030
C6050
C6120
C6130
C6200
C6220
C6230
C6250
C6320
C6330
C6410
C6600
C6610
C6620
C6740
C6760
C6770
C6900
C6910
C6920
C6950
C6980
C6990
C7001
C7101
C7200
C7210
C7221
C7231
C7241
C7251
C7301
C7320
C7401
C7420
C7470
C7480
C7490
C7601
C7602
C7611
C7800
C7810
C7901
C7911
C7941
C7970
C7980
C8000
C8010
C8020
C8030
C8040
C8050
C8090
C8100
C8110
C8120
C8130
C8140
C8150
C8160
C8170
C8180
C8190
C8200
C8210
C8230
C8250
C8260
C8300
C8310
C8320
C8330
C8340
C8350
C8360
C8370
C8380
C8390
C8400
C8410
C8420
C8430
C8500
C8510
C8520
C8600
C8610
C8620
C8630
C8640
C8650
C8700
C8710
C8720
C8730
C8740
C8800
C8810
C8900
C8930
C9000
C9040
C9050
C9060
C9070
C9080
C9180
C9500
C9510
C9540
F000
F010
F020
F021
F022
F040
F041
F050
F051
F052
F14E
F186
F278
Описание
| Error code: | C0030 |
| Description: | FAX PWB system error |
| Causes: | The FAX processing cannot be continued due to the FAX firmware error. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. |
| Error code: | C0070 |
| Description: | Toner motor |
| Causes: | Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Remedy: | 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. 2 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0100 |
| Description: | Charge corona winding problem |
| Causes: | An abnormal status is output from the flash memory. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. If not repaired, replace the main PWB. |
| Error code: | C0120 |
| Description: | MAC address data error |
| Causes: | The MAC address data is incorrect. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the MAC address The MAC address is incorrect. Replace the main PWB when the MAC address is not indicated on the network status page. |
| Error code: | C0130 |
| Description: | Backup memory read / write error |
| Causes: | The reading or writing into the flash memory is unavailable. |
| Remedy: | 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The main PWB is faulty. Reconnect the connectors on the main PWB. At that time, fix or replace the wires if they are pinched by other parts or have any damage. When the issue is not resolved, replace the main PWB. |
| Error code: | C0150 |
| Description: | Engine EEPROM reading / writing error |
| Causes: | 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing data. 2. The data read reading in 2 points mismatches 8 times continuously. 3. The read data and the write data mismatch 8 times continuously. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the EEPROM on the engine PWB The EEPROM is not properly installed. Reattach the EEPROM on the engine PWB. 3 Checking the EEPROM on the engine PWB The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. Detaching and reattaching the EEPROM 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0160 |
| Description: | Engine PWB EEPROM data error |
| Causes: | The data read from the EEPROM is judged as abnormal. |
| Remedy: | 1 Resetting the main power The EEPROM on the engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Executing U021 The storage data in the EEPROM on the engine PWB is faulty. Execute U021. Executing U021 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the engine PWB and execute U004. |
| Error code: | C0170 |
| Description: | Charger count error |
| Causes: | The values in one of the billing counters, life counter or the scanner counter mismatch between the main side and the engine side. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. Detaching and reattaching the main PWB 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0180 |
| Description: | Machine serial number mismatch |
| Causes: | The machine serial Nos. in the main PWB and the EEPROM on the engine PWB mismatch when turning the power on. |
| Remedy: | 1 Checking the machine serial No. of the main PWB The main PWB for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct main PWB if the MAIN No. differs. Executing U004 2 Checking the machine serial No. in the EEPROM on the engine PWB The EEPROM for the different main unit is installed. Check the machine serial Nos of MAIN and ENGINE at U004, and install the correct EEPROM on the engine PWB if the ENGINE machine serial No. differs. Executing U004 3 Replacing the main PWB The main PWB is faulty. If the serial number at the main is different at U004, execute U004 after replacing the main PWB. 4 Checking the EEPROM on the engine PWB The EEPROM is faulty. If the serial number at the engine is different at U004, reinstall the EEPROM on the engine PWB. If not repaired, replace the EEPROM and execute U004. Note: Please do not execute U004 in condition the serial number is different. (by selecting [Execute] and pressing [Start] key). Different serial number will be overwritten. Executing U004 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C0350 |
| Description: | Panel PWB communication error (Electronic volume I2C communication error) |
| Causes: | Since NACK was received during the I2C communication, the retry was repeated 5 times and the initial command was transmitted, and then the retry was repeated 5 times again. After that, NACK was also received. |
| Remedy: | 1 Resetting the main power The operation of the operation panel main PWB is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Operation panel main PWB - Main PWB • Operation panel main PWB - NFC PWB Wiring diagram 3 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. Detaching and reattaching the operation panel PWB 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 5 Replacing the NFC PWB The NFC PWB is faulty. Replace the NFC PWB. |
| Error code: | C0361 |
| Description: | Communication error between the engine CPU and the feed ASIC |
| Causes: | The communication with the feed ASIC failed 10 times continuously. |
| Remedy: | Resetting the main power The engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 4 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C0362 |
| Description: | Communication error between the engine CPU and the feed ASIC |
| Causes: | The communication with the feed ASIC failed 10 times continuously. |
| Remedy: | 1 Resetting the main power The engine PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed image PWB - Engine PWB Service Manual - Section 8 `PWBs` 4 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C0640 |
| Description: | Hard Disk error |
| Causes: | The HDD cannot be accessed properly. |
| Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C0650 |
| Description: | Scan sensor or scan problem |
| Causes: | The SSD (FAX image storage) used in other main unit is installed. |
| Remedy: | 1 Checking the SSD The SSD (FAX image storage) already used in other unit is installed. When installing the SSD used once, replace with the correct SSD. Detaching and reattaching the SSD 2 Executing U671 The SSD (FAX image storage) already used in other unit is reused without executing U671. If installing the used SSD, execute U671 [FAX Data CLEAR]. Executing U671 3 Reinstalling the SSD The SSD (FAX image storage) is not properly installed. Be sure to install the SSD to the connector on the main PWB. Detaching and reattaching the SSD 4 Replacing the SSD The SSD (FAX image storage) is faulty. Replace with the new SSD. Detaching and reattaching the SSD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0660 |
| Description: | Scan motor problem |
| Causes: | 1. The encrypted password input when replacing the main PWB is not correct. 2. The SSD which was used in other main unit is installed. |
| Remedy: | 1 (When the issue occurs after replacing the main PWB) Executing U004 The encryption key after replacing the main PWB is faulty. Execute U004 when this issue occurs after replacing the main PWB. Executing U004 2 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 3 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 4 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 5 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 6 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0670 |
| Description: | Hard Disk overwriting error |
| Causes: | The area that cannot be properly overwritten exists in a part of the HDD. |
| Remedy: | 1 (When abnormal sounds occur) Replacing the HDD The HDD is faulty. Replace the HDD when the abnormal sounds are from the HDD. Detaching and reattaching the HDD 2 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • HDD - Main PWB Wiring diagram 3 Initializing the HDD The HDD storage data is faulty. Execute U024 [HDD Format] > [FULL]. Executing U024 4 Replacing the HDD The HDD is faulty. Replace the HDD. Detaching and reattaching the HDD 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0680 |
| Description: | SSD error |
| Causes: | The SSD cannot be accessed, or the error occurs when accessing to the SSD. |
| Remedy: | 1 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 2 Resetting the main power The SSD is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 3 Reinstalling the SSD The SSD is not properly installed. Reinstall the SSD on the main PWB. Detaching and reattaching the SSD 4 Initializing the SSD The data stored in the SSD is faulty. Retrieve the SSD storage data at U026, and then initialize the SSD at U024. Executing U026 / U024 5 Replacing the SSD The SSD is faulty. Retrieve the SSD storage data at U026, and replace the SSD. Executing U026 / detaching and reattaching the SSD 6 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0800 |
| Description: | Image processing error |
| Causes: | The print sequence jam (J010x) was detected 2 times continuously. |
| Remedy: | 1 Checking the image data The image data is faulty. When this issue occurs only when handling the certain image data, check if the image data is faulty. 2 Checking the situation The printing operation of the certain file is faulty. Acquire the jobs log if the phenomenon can be reproduced by specifying the job when the error was detected.` 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Reinsert all the connectors on the main PWB. If the wire is pinched by other parts or it is damaged, repair or replace the wire. Detaching and reattaching the main PWB 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0830 |
| Description: | FAX PWB flash program area checksum error |
| Causes: | The program stored in the flash memory on the FAX PWB is broken so it cannot perform. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 2 Checking the FAX PWB The FAX PWB is not properly connected. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0840 |
| Description: | RTC error ("Time for maintenance T" appears) |
| Causes: | [Check at start-up] • RTC values are old. • Power has not been turned on for over 5 years. • RTC value is older than 2000/1/1 00:01. [Periodic check per 5 minutes after start-up] • RTC values are older than the ones at the last check. • Partial operation by power reset after C840 error and "Time for Maintenance T" is indicated. |
| Remedy: | 1 Executing U906 The backup battery on the main PWB is faulty, and so, the RTC settings are erased after unplugging the power cord. Execute U906 to reset the display [Maintenance T]. After that, set the date/time (RTC) in the System menu. (It is necessary to execute this process whenever to unplug/plug the power cord.) Executing U906 2 Replacing the main PWB The main PWB is faulty, or the backup battery runs out. If service call error C0840 frequently appears after performing the previous step, replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C0850 |
| Description: | TPM security chip error |
| Causes: | TPM is not accessible or an access error occurs after installing the security kit |
| Remedy: | 1 Reset the main power Main PWB does not operate properly Turn the power switch and main power switch off. Turn the power switch and main power switch on after passing 5s 2 Upgrading the firmware The firmware version is not the latest Upgrade the firmware to the latest version 3 Replacing main PWB Main PWB is faulty Replace main PWB |
| Error code: | C0870 |
| Description: | PC FAX Image data transmission error |
| Causes: | Data was not properly transmitted even if the specified times of retry were made when the large volume data is transmitted between the FAX PWB and the main PWB. |
| Remedy: | 1 Resetting the main power The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 2 Initializing the fax The data in the FAX PWB is faulty. Execute U600 to initialize the FAX. Executing U600 3 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 6 Executing U024 The data stored in the SSD is faulty. Execute U024 [SSD Format]. Executing U024 |
| Error code: | C0920 |
| Description: | 1st drawer lift |
| Causes: | The backup data could not be stored since the file system of the flash memory is faulty. |
| Remedy: | 1 Initializing the fax FAX control values are incorrect Execute U600 to initialize the FAX. Executing U600 2 Checking the FAX PWB The FAX PWB does not operate properly. Turn the power switch and the main power switch off . After 5s passes, reattach the FAX PWB and turn the main power switch and the power switch on. FAX Installation Guide 3 Reinstalling the FAX PWB The FAX PWB is not properly installed. Reinstall the FAX PWB. FAX Installation Guide 4 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 5 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | C0950 |
| Description: | 4th drawer lift problem |
| Causes: | Print processing of the received FAX could not be executed and the job continues staying. |
| Remedy: | 1 Resetting the main power The printing process is not properly executed. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is faulty. Upgrade the main firmware to the latest version. Firmware upgrade |
| Error code: | C0980 |
| Description: | 24V power interruption detection |
| Causes: | 1. The 24V power interruption signal was detected for 1s continuously. 2. After passing 100ms since the 24V power interruption signal was detected, the other service call error appeared. Then, the 24V power supply recovered. |
| Remedy: | 1 Resetting the main power The printing process is not properly executed. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • LVU - Engine PWB Wiring diagram 3 Replacing the LVU The LVU is faulty. Replace the LVU if +24V output from the LVU is not stable and reduced. Detaching and reattaching the LVU 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1000 |
| Description: | MP lift motor error |
| Causes: | The upper MP lift sensor (for upper limit detection) or lower MP lift sensor (for lower limit detection) does not detect turning on for 3s when the MP lift motor ascends or descends. |
| Remedy: | 1 Checking the lift base The lift base does not properly operate. If the lift base of the MP tray does not move up and down, repair or replace the lift base. 2 Checking the lift lever The lift lever is not properly attached. Check if the lift lever is located where it moves up and down by the lift motor cam or has no damage. Then, reattach the MP tray or replace the lift lever. 3 Checking the drive gear The drive gears for lifting up the lift base do not properly rotate. Check if the drive gears for lifting up the lift base can rotate smoothly or have no excessive load. Then, apply grease and repair the parts. 4 Checking the conveying unit The drawer connector connection between the conveying unit and the main unit is faulty. Firmly close the conveying unit. If there are foreign objects or the deformation on the drawer connector of the conveying unit for connecting to the main unit, repair them. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MP lift motor - Relay PWB • Relay PWB - Feed PWB Wiring diagram 6 Checking the MP lift motor The MP lift motor is faulty. Check the MP lift motor operation, and replace the motor if necessary. 7 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Upper or lower MP lift sensor - Relay PWB • Relay PWB - Feed PWB Wiring diagram 8 Checking the sensor The upper or lower MP lift sensor is not properly attached or faulty. Reattach the upper or lower MP lift sensor. If not repaired, replace the sensor. 9 Replacing the relay PWB The relay PWB is faulty. Replace the relay PWB. 10 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 11 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 12 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1010 |
| Description: | Lift motor 1 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 1 is installed. 2. The lock-up signal is not released for 1s after lift motor 1 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift motor 1 - Feed PWB Wiring diagram 4 Checking lift motor 1 Lift motor 1 is faulty. Check the operation of lift motor 1, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 1 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 1 is not properly attached or faulty. Reattach lift sensor 1. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1020 |
| Description: | Lift motor 2 error |
| Causes: | Either of the following was detected 5 times continuously. 1. Lift sensor 2 does not turn on when passing 12s after cassette 2 is installed. 2. The lock-up signal is not released for 1s after lift motor 2 turns on. |
| Remedy: | 1 Checking the cassette base The cassette base does not operate properly. Repair or replace the cassette base if it cannot move vertically. 2 Checking the drive gear The drive gear to lift up the cassette base does not rotate properly. Check if the drive gears to lift up the cassette base rotate smoothly or have no excessive load. And apply the grease to the frictional parts and repair the related parts so that they can rotate smoothly. 3 Checking the wire The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Lift motor 2 - Feed PWB Wiring diagram 4 Checking lift motor 2 Lift motor 2 is faulty. Check the operation of lift motor 2, and replace it if necessary. Detaching and reattaching the lift motor 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Lift sensor 2 - Feed PWB Wiring diagram 6 Checking the sensor Lift sensor 2 is not properly attached or faulty. Reattach lift sensor 2. If not repaired, replace the sensor. 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1030 |
| Description: | Lift motor 3 error • When cassette 3 is inserted, lift limit switch 3 does not turn on within 33 s of lift motor 3 turning on. This error is detected four times successively. • During copying, lift limit switch 3 does not turn on within 1 s of lift motor 3 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 3. Defective lift motor 3. Poor contact of lift motor 3 connector terminals. Defective lift limit switch 3. Poor contact of lift limit switch 3 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 3. Replace lift motor 3. Defective lift motor 3. Check for continuity across the coil. If none, replace lift motor 3. Poor contact of lift motor 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 3. Run maintenance item U031 and turn lift limit switch 3 on and off manually. Replace lift limit switch 3 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 3 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB |
| Error code: | C1040 |
| Description: | Lift motor 4 error • When cassette 4 is inserted, lift limit switch 4 does not turn on within 33 s of lift motor 4 turning on. This error is detected four times successively. • During copying, lift limit switch 4 does not turn on within 1 s of lift motor 4 turning on. This error is detected four times successively. |
| Causes: | Broken gears or couplings of lift motor 4. Defective lift motor 4. Poor contact of lift motor 4 connector terminals. Defective lift limit switch 4. Poor contact of lift limit switch 4 connector terminals. Defective casette PWB. |
| Remedy: | Broken gears or couplings of lift motor 4. Replace lift motor 4. Defective lift motor 4. Check for continuity across the coil. If none, replace lift motor 4. Poor contact of lift motor 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective lift limit switch 4. Run maintenance item U031 and turn lift limit switch 4 on and off manually. Replace lift limit switch 4 if indication of the corresponding sensor on the touch panel is not displayed in reverse. Poor contact of lift limit switch 4 connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Defective casette PWB. Replace the casette PWB. |
| Error code: | C1140 |
| Description: | PF lift motor error Object: Side feeder |
| Causes: | 1. The PF lift upper limit sensor does not turn on when passing 30s after cassette 5 is inserted. 2. The lock-up signal is detected for 200ms continuously during the PF lift motor operation. 3. The PF lift upper limit sensor does not turn on when passing 2s after the upper limit control when printing starts. |
| Remedy: | 1 Checking the bottom plate The bottom plate does not operate properly. Repair or replace the bottom plate when it does not move vertically. 2 Checking the drive gear The drive gear to lift up the bottom plate does not rotate properly. Check if the drive gears to lift up the bottom plate rotate smoothly or have no excessive load. And apply the grease to the frictional parts and fix the related parts so that they can rotate smoothly. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift motor - PF main PWB Wiring diagram 4 Checking the PF lift motor The PF lift motor is faulty. Replace the PF lift motor. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF lift upper limit sensor - PF main PWB Wiring diagram 6 Checking the PF lift upper limit sensor The PF lift upper limit sensor is not properly attached or faulty. Reattach the PF lift upper limit sensor. Then, replace it if it is not fixed. 7 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. Detaching and reattaching the PF main PWB |
| Error code: | C1750 |
| Description: | AK unit type mismatch error |
| Causes: | Connection of the AK for other model is detected when checking the DF installation status |
| Remedy: | 1 Checking AK unit AK-7100 is installed. Install AK=7100. |
| Error code: | C1800 |
| Description: | Large capacity feeder communication error Condition: When turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error does not reappear. (It is caused by the large capacity feeder.) |
| Causes: | The communication error was detected 10 times continuously. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1820 |
| Description: | Side Feeder communication error Object: Side feeder |
| Causes: | The communication error was detected 10 times continuously. |
| Remedy: | 1 Checking the connection It is not properly connected to the main unit. Reconnect the cable of the side feeder to the main unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB - Engine PWB Wiring diagram 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side feeder firmware to the latest version. Firmware Update 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side feeder) Detaching and reattaching the PF main PWB (Side feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1900 |
| Description: | Large capacity feeder EEPROM error Condition: When outputting Event Log after turning the main power off and on while disconnecting the connector of the cable from the side multi feeder, this service call error is not recorded. (It is caused by the large capacity feeder.) (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously when writing. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the large capacity feeder firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB (Large capacity feeder) - PF main PWB (Side multi feeder) • PF main PWB (Side multi feeder) - Engine PWB Wiring diagram 3 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Large capacity feeder) Detaching and reattaching the PF main PWB (Large capacity feeder) 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side multi feeder) Detaching and reattaching the PF main PWB (Side multi feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1920 |
| Description: | Side Feeder EEPROM error (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously when writing. |
| Remedy: | 1 Checking the connection It is not properly connected to the main unit. Reconnect the cable of the side feeder to the main unit. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF main PWB - Engine PWB Wiring diagram 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware and the side feeder firmware to the latest version. Firmware Update 4 Replacing the PF main PWB The PF main PWB is faulty. Replace the PF main PWB. (Side feeder) Detaching and reattaching the PF main PWB (Side feeder) 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C1950 |
| Description: | Primary transfer belt unit EEPROM error |
| Causes: | The EEPROM cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data do not match 8 times continuously. |
| Remedy: | 1 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed or the connector is not connected. Reinstall the primary transfer belt unit and reconnect the connector. Detaching and reattaching the primary transfer belt unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 3 Primary transfer belt unit replacement The primary transfer belt unit is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2201 |
| Description: | Drum motor steady-state error |
| Causes: | The ready signal is at the H level for 1s continuously after the drum motor became stable. |
| Remedy: | 1 Checking the drum motor The drum motor drive is faulty. Execute U030 [Process] and check the drum motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the drum unit and the developer unit The drum unit is faulty. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 4 Checking the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 5 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2300 |
| Description: | Fuser motor error |
| Causes: | 1. The ready signal is at the H level for 1s continuously during the fuser motor drive. 2. The ready signal is not at the L level (stable rotation) when passing 2s after the fuser motor drive starts. |
| Remedy: | 1 Checking the fuser motor The fuser motor operation is faulty. Execute U030 [Fuser] and check the fuser motor operation. Check if the drive gears rotate smoothly and have no excessive load. Then, apply grease to the frictional parts and repair the parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Fuser motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 4 Replacing the fuser motor The fuser motor is faulty. Replace the fuser motor. Detaching and reattaching the fuser drive unit 5 Replacing the fuser drive unit The fuser drive unit is faulty. Replace the fuser drive unit. Detaching and reattaching the fuser drive unit 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C2500 |
| Description: | Feed motor error |
| Causes: | The ready signal is not at the L level after passing 2s since the feed motor drive was started. |
| Remedy: | 1 Checking the feed motor The operation of the feed motor is faulty. Execute U030 [Feed] to check the feed motor operation. Check if the drive gears rotate and have no excessive load, and apply the grease (EM-LP, Part no: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the feed motor The feed motor is faulty. Replace the feed motor. 4 Replacing the feed drive unit The feed drive unit is faulty. Replace feed drive unit. Detaching and reattaching the Feed Drive Unit 5 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 6 Firmware upgrade The firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB 8 Replacing the feed image PWB The power can`t be supplied to the feed drive PWB. Replace the feed image PWB. |
| Error code: | C2600 |
| Description: | PF feed motor error |
| Causes: | The ready signal is not at the L level (stable rotation) after passing 1s since the PF feed motor drive started. |
| Remedy: | 1 Checking the PF feed motor The PF feed motor is not properly connected, or it is faulty. Execute U247 [2PF] or [LCF] > [Motor On] to check the paper feed operation. If the PF feed motor does not operate properly, reconnect the connector of the motor. Check if the PF feed roller and the drive gears rotate smoothly and have no excessive load, apply the grease (EM-50LP, Part no.: 7BG010009H) to the sliding section and repair the related parts so that they can rotate smoothly. Maintenanc e Mode List 2 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PF feed motor - PF PWB • PF PWB - Engine PWB (Drawer connector between the paper feeder and the main unit) Service Manual - Section 8 `PWBs` 3 Replacing the PF feed motor The PF feed motor is faulty. Replace the PF feed motor. Detaching and reattaching the PF Drive Unit 4 Firmware upgrade The engine firmware or the PF firmware is faulty. Upgrade the engine firmware and the PF firmware to the latest version. Firmware Update 5 Replacing the PF PWB The PF PWB is faulty. Replace the PF PWB. Detaching and reattaching the PF PWB 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C2700 |
| Description: | Color release motor error |
| Causes: | Turning the color release sensor on and off is not detected for 5s while the color release motor is driving. |
| Remedy: | 1 Checking the drive components The drive transmission from the color release motor error is faulty. Execute U030 [CMY Release]. If the drive from the motor is not transmitted, repair the drive parts. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 5 Primary transfer belt unit replacement The primary transfer roller lift-up drive section is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2760 |
| Description: | Transfer motor startup error |
| Causes: | The belt motor FG signal is not stable when passing 5s after the transfer motor drive starts. |
| Remedy: | 1 Checking the drive components The drive transmission from the transfer motor is faulty. Check if the excessive load is not applied to the drive gears, rollers and the belt by rotating them, and clean the drive parts of the primary transfer belt unit. Executing U030 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Transfer motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Checking the primary transfer belt unit The primary transfer belt unit is not properly installed or faulty Reinstall the primary transfer belt unit. If not repaired, replace it. Detaching and reattaching the primary transfer belt unit 4 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Checking the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2810 |
| Description: | Waste toner motor error |
| Causes: | The steady-state speed error, FG pulse abnormal stop, or the abnormal motor drive is detected when reading the error signal from the motor at every 1s. |
| Remedy: | 1 Checking the waste toner box The waste toner box is not properly installed. Reinstall the waste toner box. Detaching and reattaching the waste toner box 2 Checking the waste toner motor The waste toner motor does not operate properly. Check if the waste toner motor has no excessive load, and repair it. 3 Checking the drive gear The drive gear does not rotate properly. Check if the excessive load is not applied to the drive gears by rotating the gears, and clean the drive gears and the bushing, etc. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Waste toner motor - Front PWB?• Front PWB - Engine PWB Wiring diagram 5 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C2840 |
| Description: | Transfer cleaning motor error |
| Causes: | 1. The ready signal does not turn on when passing 2s after the transfer cleaning motor starts. 2. The ready signal turns off for 1s continuously after the transfer cleaning motor is stable. |
| Remedy: | 1 Checking the primary transfer belt unit The primary transfer belt unit is not properly installed. Reattach the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 2 Cleaning the primary transfer cleaning section The roller in the primary transfer cleaning section does not rotate properly. Remove the waste toner remaining in the primary transfer cleaning section. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Transfer cleaning motor - Relay connector of the primary transfer belt unit • Relay connector of the primary transfer belt unit - Engine PWB Wiring diagram 4 Checking the transfer cleaning motor The transfer cleaning motor is not properly attached or faulty. Reattach or replace the transfer cleaning motor. 5 Primary transfer belt unit replacement The primary transfer cleaning section is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3100 |
| Description: | Carriage error |
| Causes: | When turning the power on or finishing originals scan through the scanner, the alignment of the home position sensor (turning on / off the sensor) fails and the error is detected. Then, the error is detected twice continuously even the initial operation is executed. |
| Remedy: | 1 Unlocking the scanner mirror frame The scanner mirror frame is not unlocked. Unlock the scanner mirror frame (lamp unit assy). Unlocking the scanner mirror frame 2 Checking the scanner movement A load is applied to the scanner movement. Check the operation of the lamp by U073 or manually moving it. If there is an excess load, check if there are any foreign objects on the optical wire or optical wire drum and clean it. After that, apply grease on the scanner rail. Detaching and reattaching the scanner wires 3 Checking the scanner wires The scanner wires are dirty or come off. Clean and reattach the scanner wires. Detaching and reattaching the scanner wires 4 Checking the scanner motor The scanner motor is faulty. Reattach the scanner motor and reconnect the connector. If not repaired, replace it. 5 Checking the belt tension of the scanner motor A load is applied to the scanner movement since the belt tension is improper. Adjust the scanner motor belt tension properly. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Scanner motor - Engine PWB Wiring diagram 7 Checking the home position sensor The home position sensor is not properly attached. Reattach the home position sensor. 8 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Home position sensor - Engine PWB Wiring diagram 9 Replacing the home position sensor The home position sensor is faulty. Replace the home position sensor. 10 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3200 |
| Description: | LED lamp startup error |
| Causes: | The white reference data acquired by lighting the LED lamp at the initial operation does not reach the specified value. Or, the light amount detected by the CCD PWB is not enough. (2 or more LED lamps do not light. The light does not reach the CCD PWB due to condensation.) |
| Remedy: | 1 Checking the LED lamp The LED lamp does not light. Execute U061 [CCD] and check if the LED lamp is lit. If not, replace the lamp unit. After that, execute U411 [Table(ChartA)]. Detaching and reattaching the lamp unit 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB • LED PWB - CCD PWB Wiring diagram 3 Checking the mirror The mirror or lens is frosted due to condensation. Clean the mirrors. If the condensation at the scanner section is resolved naturally by opening the document processor or the platen cover, turn the power switch off and on. 4 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3210 |
| Description: | CIS lamp error |
| Causes: | Input data did not exceed the threshold for 5s when the CIS lamp was ON. |
| Remedy: | 1 Releasing the partial operation The partial operation is executed. Execute resetting the partial operation at U906. Executing U906 2 Checking the DPCIS The CIS lamp does not light. Execute U061 [CIS] and check if the CIS lamp is lit. If not, replace the DPCIS and execute U411. Detaching and reattaching the CIS 3 Cleaning the CIS glass and the CIS roller The CIS glass or the CIS roller is dirty. Clean the CIS glass and the CIS roller. 4 Checking the DPSHD PWB The DPSHD PWB is not properly connected. Reconnect the DPSHD PWB to the DPCIS. 5 Checking the connection The connector is not properly connected. Or, the SATA cable or the wire is faulty. Clean the following SATA cable or the terminal of the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • DPSHD PWB - DP relay PWB • DP relay PWB - Main PWB • DP relay PWB - DP main PWB • DP main PWB - Engine PWB Wiring diagram 6 Firmware upgrade The firmware is not the latest version. Upgrade the DP firmware to the latest version. Firmware Update 7 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. 8 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. 9 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 10 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 11 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3300 |
| Description: | CCD AGC error (For the internal count) |
| Causes: | Brightness of the LED lamp is darker while one of the LED lamp does not turn on or brighter than expected when processing the AGC for the CCD lamp. |
| Remedy: | 1 Checking the LED lamp The LED lamp is faulty. Check if the LED lamp lights by executing U061 [CCD]. If it does not light, replace the lamp unit and execute U411 [Table (ChartA) ]. Detaching and reattaching the lamp unit 2 Cleaning the backside of the contact glass The white reference sheet is dirty. Clean the white reference sheet at the backside of the contact glass. Detaching and reattaching the contact glass 3 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is peeled off, deformed or the FFC is broken, replace the FFC. • LED PWB - CCD PWB • CCD PWB - Engine PWB Wiring diagram 4 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 5 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3310 |
| Description: | CIS AGC error (For the internal count) |
| Causes: | The CIS could not get the normal white reference value after the AGC retry. |
| Remedy: | 1 Releasing the partial operation The partial operation is executed. Execute resetting the partial operation at U906. Executing U906 2 Cleaning the CIS glass and the CIS roller The CIS glass or the CIS roller is dirty. Clean the CIS glass and the CIS roller. 3 Firmware upgrade The firmware is not the latest version. Upgrade the DP firmware to the latest version. Firmware Update 4 Checking the DPSHD PWB The DPSHD PWB is not properly connected. Reconnect the DPSHD PWB to the DPCIS. 5 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. 6 Replacing the DPCIS The DPCIS is faulty. Replace the DPCIS, and then execute U091 and U411. Detaching and reattaching the DPCIS 7 Checking the connection The connector is not properly connected. Or, the SATA cable is faulty. Clean the terminal of the following SATA cable connector and reconnect the connectors. If there is no continuity, replace the SATA cable. • DPSHD PWB - DP relay PWB • DP relay PWB - Main PWB Wiring diagram 8 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. 9 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB |
| Error code: | C3500 |
| Description: | Communication error between the scanner and the ASIC |
| Causes: | The communication error is detected during the communication between the scanner ASIC and the scanner CPU. |
| Remedy: | 1 Resetting the main power ASIC does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware to the latest version. Firmware Update 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3600 |
| Description: | Scanner sequence error |
| Causes: | The program internal processing error of the scanner sequence occurs. |
| Remedy: | 1 Executing U021 The memory operation is faulty. Execute U021. Executing U021 2 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C3800 |
| Description: | AFE error |
| Causes: | The writing data and the reading data mismatch 3 times continuously when writing. No response is not returned from AFE for 100ms. |
| Remedy: | 1 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is peeled off, deformed or the FFC is broken, replace the FFC. • CCD PWB - Engine PWB Wiring diagram 2 Replacing the lens unit The CCD PWB is faulty. Replace the lens unit and execute U411. Detaching and reattaching the lens unit 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4001 |
| Description: | Polygon motor synchronization error |
| Causes: | The ready signal is not at the L level when passing 30s after the polygon motor drive starts. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Polygon motor - Engine PWB Wiring diagram 2 Checking the polygon motor The polygon motor does not rotate properly. Check the rotation sound of the polygon motor, and reattach or replace the LSU if it does not rotate properly. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4011 |
| Description: | Polygon motor steady-state error |
| Causes: | The ready signal is at the H level for 15s continuously after the polygon motor drive becomes stable. |
| Remedy: | 1 Checking the connection FFC is not connected properly. Or it is faulty. Clean the FFC terminals of the following FFC and reconnect them. If the FFC terminal is deformed or broken, replace the FFC. • LSU (APC PWB) - Engine PWB Service Manual - Section 8 `PWBs` 2 Checking the polygon motor The polygon motor does not rotate properly. Check the rotation sound of the polygon motor, and reattach or replace the LSU if it does not rotate properly. Detaching and reattaching the LSU 3 Firmware upgrade The engine firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C4101 |
| Description: | BD initialization error |
| Causes: | The BD signal was not detected for 1s after driving the polygon motor. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4201 |
| Description: | BD steady-state error |
| Causes: | The BD signal is not detected during the laser lighting. |
| Remedy: | 1 Checking the connection The connector or the FFC terminal is not properly connected, or the wire or the FFC is faulty. Reconnect the following wire connectors and reconnect the FFC. If there is no continuity, replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. • APC PWB - LSU relay PWB • LSU relay PWB - Engine PWB 2 Checking the LSU The BD sensor or the laser diode is faulty. Reinstall or replace the LSU while paying attention to the static electricity. Detaching and reattaching the LSU 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C4600 |
| Description: | LSU cleaning motor error |
| Causes: | The LSU cleaning motor lock-up is detected. Or, the motor continues shifting for 8s or more in the same direction. |
| Remedy: | 1 Executing the Laser Scanner Cleaning The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Execute Laser Scanner Cleaning. 2 Cleaning the LSU cleaning drive gear and the cleaning pad The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Clean the LSU cleaning drive gear and the cleaning pad. 3 Replacing the LSU The LSU cleaning drive gear, cleaning wire or pad is deformed or faulty. Replace the LSU. Detaching and reattaching the LSU 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • LSU cleaning motor - Engine PWB Wiring diagram 5 Checking the LSU cleaning motor The LSU cleaning motor is not properly attached or faulty. Reattach the LSU cleaning motor. If not repaired, replace the motor. 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4701 |
| Description: | VIDEO ASIC device error 1 |
| Causes: | Communication with VIDEO ASIC failed 10 times continuously. (After writing to the VIDEO ASIC, when scanned from the same address, the value does not match.) |
| Remedy: | 1 Resetting the main power The ASIC operation on the engine is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4702 |
| Description: | VIDEO ASIC device error 2 |
| Causes: | Communication with VIDEO ASIC (2) failed 10 times continuously. (Value mismatch error when scanning from the same address after writing on the VIDEO ASIC.) |
| Remedy: | 1 Resetting the main power The ASIC operation on the engine is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C4801 |
| Description: | LSU type mismatch error |
| Causes: | The LSU mismatches with the main unit. |
| Remedy: | 1 Checking the LSU The different type LSU is installed. Install the correct LSU. Detaching and reattaching the LSU 2 Checking the connection FFC is not connected properly. Or it is faulty. Clean the FFC terminals of the following FFC and reconnect them. If the FFC terminal is deformed or broken, replace the FFC. • LSU (APC PWB) - Engine PWB Service Manual - Section 8 `PWBs` 3 Replacing the LSU The APC PWB is faulty. Replace the LSU. Detaching and reattaching the LSU |
| Error code: | C5101 |
| Description: | Main high-voltage error |
| Causes: | When the flow-in current with the Vpp variable in 3 steps is measured during the Vpp adjustment, difference between the zero current value and 2nd step current value is less than the reference value. (The Vpp is adjusted at warm-up, before calibration or before print when the in-machine temperature varies largely from the one at the last time Vpp adjustment.) |
| Remedy: | 1 Reinstalling the high-voltage PWB Proper electric current does not flow as the main charger roller contact is not properly grounded. Repair the main charger roller contact (wire spring) inside the high-voltage PWB so that it firmly contacts. Detaching and reattaching the high-voltage PWB 2 Checking the drum unit and the developer unit The drum or the drum screw does not properly rotate due to the excessive load. Check if the drum or the drum screw rotates manually, and if not, replace drum unit. Detaching and reattaching the drum unit 3 Replacing the drum motor The drum motor is faulty. Replace the drum motor. Detaching and reattaching the drum drive unit 4 Checking the main charger unit Proper electric current does not flow as the foreign objects are adhered on the high-voltage contact of the main charger roller unit. Clean the high-voltage contact of the main charger roller unit and apply conductive grease to the roller shaft. Detaching and reattaching the main charger roller unit 5 Replacing the main charger roller unit Proper electric current does not flow due to deformation or damage of the high-voltage contact of the main charger roller unit. Replace the main charger roller unit and execute U930. Detaching and reattaching the main charger roller unit 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity.• High-voltage PWB - Engine PWB Wiring diagram 7 Replacing the high-voltage PWB The high-voltage PWB is faulty. Replace the high-voltage PWB. Detaching and reattaching the high-voltage PWB 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C5130 |
| Description: | Primary transfer high-voltage error Object: Monochrome models |
| Causes: | When adjusting the feedback, the detected electric current value exceeds the upper limit or is less than the lower limit, or the adjustment result is 300V or less or is 2,900V or more. |
| Remedy: | 1 Reinstalling the primary transfer unit The primary transfer unit is not properly installed. Reinstall the primary transfer unit so that the connector firmly connects. Primary Transfer Unit Replacement 2 Checking the high-voltage contact Foreign material adheres on the high-voltage contacts of the primary transfer roller, and so, the proper voltage is not applied. Clean the high-voltage contact of the primary transfer roller, and apply conductive grease to the roller shaft. 3 Reinstalling the transfer high-voltage PWB The high-voltage contacts on the transfer high-voltage PWB are faulty, and so, the proper voltage is not applied. Reinstall the transfer highvoltage PWB. Transfer High-voltage PWB Replacement 4 Checking the wire The wire is not properly connected or is faulty. Reinsert the following wire connectors, and replace the wires if there is no continuity.• Transfer high-voltage PWB - Engine PWB• Transfer highvoltage PWB - Feed image PWB Electrical Diagram of PWBs 5 Replacing the transfer high-voltage PWB The transfer high-voltage PWB is faulty. Replace the transfer highvoltage PWB. Transfer High-voltage PWB Replacement 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Upgrade 7 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Engine PWB Replacement |
| Error code: | C6000 |
| Description: | IH heating error 1 |
| Causes: | The fuser center thermistor temperature does not reach 100°C / 212°F when passing 60s since warm-up starts. Or, the ready display temperature is not detected when passing 420s since the fuser center thermistor temperature reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Executing U169 The IH setting mismatches the power source specification. Set the fuser destination same as the IH PWB voltage at U169. Executing U169 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature cannot be detected properly due to the broken thermostat or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6020 |
| Description: | Fuser center thermistor high temperature error |
| Causes: | The fuser center thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6030 |
| Description: | Fuser center thermistor broken |
| Causes: | The output from the fuser center thermistor is under 20°C / 68°F level during warm-up. Or, the temperature detected at the fuser center thermistor does not change for 10s after turning the fuser heater on. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6050 |
| Description: | Fuser center thermistor low temperature error |
| Causes: | The fuser center thermistor detects less than 100°C / 212°F for 1s after warm-up, or during print or standby. |
| Remedy: | 1 Changing the wall outlet The power voltage descends by 10% or more of the rated voltage when printing. Connect the power cord to a different wall outlet if the power supply voltage descends by 10% or more of the rated voltage. 2 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 3 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 6 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 11 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit |
| Error code: | C6120 |
| Description: | Fuser press thermistor high temperature error |
| Causes: | The fuser press thermistor detects 210°C / 410°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the thermistor error, etc. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6130 |
| Description: | Fuser press thermistor broken |
| Causes: | The detection temperature of the fuser press thermistor does not reach 30°C / 86°F within 60s since warm-up starts. |
| Remedy: | 1 Removing foreign material There are foreign objects between the fuser press thermistor and the press roller. Or, the foreign objects are adhered on the press roller. Remove foreign objects if any on the press roller. Then, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6200 |
| Description: | Fuser IH ends heating error |
| Causes: | The temperature detected at the fuser edge thermistor does not reach 100°C / 212°F within 60s since warmup starts. The temperature detected at the fuser edge thermistor does not reach the ready display temperature within 60s since it reaches 100°C / 212°F during warm-up. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. 6 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. Executing U030 7 Replacing the current PWB The current PWB is faulty. Replace the current PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 11 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 12 Replacing the IH unit The IH unit is faulty. Replace the IH unit. |
| Error code: | C6220 |
| Description: | Fuser edge thermistor high temperature error |
| Causes: | The fuser edge thermistor detects 240°C / 464°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature is not properly detected due to the broken wire or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. 8 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 9 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 10 Checking the fuser edge fan motor Dust accumulates on the fuser edge fan motor, or the motor is not properly attached. Clean the front / rear fuser edge fan motors and reattach them. Fan Motors Attachable Direction |
| Error code: | C6230 |
| Description: | Fuser edge thermistor broken |
| Causes: | The fuser edge thermistor detects 37°C / 98°or less for 1s when the fuser center thermistor detects 100°C / 212°F or more for 1s during warm-up. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature cannot be detected properly due to the heater broken or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. 9 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 10 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 11 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. |
| Error code: | C6250 |
| Description: | Fuser edge thermistor low temperature error |
| Causes: | The fuser edge thermistor detects less than 100°C / 212°F for 1s during print or standby. |
| Remedy: | 1 Removing foreign material There is foreign material between the fuser unit and the IH unit. Or, foreign material adheres on the heat roller. Remove foreign objects if they are in between the fuser unit and the IH unit or on the heat roller. After that, reinstall the fuser unit. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the fuser unit The temperature cannot be detected properly due to the heater broken or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 7 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 8 Checking the IH core motor The small size shield plate of the IH core motor does not shift to the proper position. Execute U030 [IH Core] and check the IH core motor rotation. If the motor does not properly operate, repair it. Detaching and reattaching the fuser IH PWB 9 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB Wiring diagram 10 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 11 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6320 |
| Description: | Fuser A3 thermistor high temperature error |
| Causes: | The fuser A3 thermistor detects 215°C / 419°F or more for 1s. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 4 Replacing the fuser unit The temperature is not properly detected due to the wire short-circuit or the thermistor error in the fuser unit. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH unit The IH unit is faulty. Replace the IH unit. 8 Checking the fuser edge fan motor Dust accumulates on the fuser edge fan motor, or the motor is not properly attached. Clean the front / rear fuser edge fan motors and reattach them. Fan Motors Attachable Direction |
| Error code: | C6330 |
| Description: | Fuser A3 thermistor broken |
| Causes: | The fuser A3 thermistor detects 20°C / 68°F or less when the fuser center thermistor detects 100°C / 212°F or more during warm-up. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB • Connector of the fuser unit - IH PWB • IH PWB - Engine PWB • IH PWB - Feed PWB • IH PWB - IH unit Wiring diagram 4 Replacing the fuser unit The temperature cannot be detected properly due to the heater broken or the thermistor error. Replace the fuser unit. Detaching and reattaching the fuser unit 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 8 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB |
| Error code: | C6410 |
| Description: | Fuser unit type mismatch error |
| Causes: | "Unit Identification" code in the EEPROM of the fuser unit does not match the main unit. The fuser unit for other model is installed. |
| Remedy: | 1 Replacing the fuser unit The fuser unit for other models is installed. Install the fuser unit for the applicable models. Detaching and reattaching the fuser unit 2 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB Wiring diagram 5 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6600 |
| Description: | Fuser belt rotation error |
| Causes: | The belt rotation pulse is not input for 1.8s continuously. |
| Remedy: | 1 Reinstalling the fuser unit The fuser unit is not properly installed. Check if the fuser rollers rotate manually. After checking it, reinstall the fuser unit while paying attention to the drive gears engagements. Detaching and reattaching the fuser unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB Wiring diagram 3 Replacing the fuser unit The fuser unit components such as the fuser belt, belt rotation detection mechanism or fuser belt sensor are faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 4 Applying the grease The load increases due to the lack of grease on the bushing or the gears for the fuser motor. Execute U030 [Fuser] and check the fuser motor operation. If the motor does not smoothly rotate, apply grease to the bushing and the gears. Executing U030 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Fuser motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 6 Replacing the fuser drive gear The fuser drive gear is faulty. Replace the fuser drive gear. 7 Replacing the fuser motor The fuser motor is faulty. Replace the fuser motor. Detaching and reattaching the fuser drive unit 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 10 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. |
| Error code: | C6610 |
| Description: | Fuser release sensor error |
| Causes: | 1. The fuser release sensor does not turn off when passing 5s from the instruction to the fuser release motor to reduce the fuser pressure. 2. The fuser release sensor does not turn on when passing 5s from the instruction to the fuser release motor to increase the fuser pressure. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, reinstall the fuser unit so that the connector is firmly connected. Detaching and reattaching the fuser unit 2 Checking the motor operation / connection The connector is not properly connected. Or, the wire is faulty. Execute U030 [Fuser Release] and check the fuser release motor operation. If the motor does not properly operate, clean the terminal of the following wire connectors and reconnect them. If there is no continuity, replace the wire. • Connector of the fuser unit - Engine PWB Wiring diagram 3 Replacing the fuser unit The fuser release motor or the fuser release sensor, etc. is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6620 |
| Description: | IH core motor rotation error |
| Causes: | 1. The IH core sensor does not turn on within 5s after the IH core motor drives while the IH core sensor is off at the operation of the home position detection. 2. The IH core sensor turning off and on is not detected within 5s after the IH core motor drives while the IH core sensor is on at the operation of the home position detection. |
| Remedy: | 1 Checking the IH unit The connector of the IH unit is not properly connected. Check if the connector pins of the IH unit are bent, and correct them if bent. When there is no problem, reinstall the IH unit so that the connector is firmly connected. Detaching and reattaching the IH unit 2 Checking the IH core sensor The IH core sensor is not properly attached. Reattach the IH core sensor if it comes off. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH core motor and IH core sensor (IH unit ) - Front PWB?• Front PWB - Engine PWB Wiring diagram 4 Replacing the IH unit The IH core sensor or the IH core motor is faulty. Replace the IH unit. Detaching and reattaching the IH unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6740 |
| Description: | IH PWB high temperature error |
| Causes: | The IGBT temperature detected by the IH PWB is 115°C / 239°F or more for 1s continuously. |
| Remedy: | 1 Checking the IH fan motor Dust accumulates on the IH fan motor. Clean the IH fan motor. The procedure of installing the fan motor. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH fan motor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 3 Replacing the IH fan motor The IH fan motor is faulty. Execute U037 [IH PWB] and check the IH fan motor operation. If the fan motor does not properly operate, replace it. Executing U037 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH PWB - Engine PWB • IH PWB - Feed PWB Wiring diagram 5 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 8 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. [C |
| Error code: | C6760 |
| Description: | Fuser IH input excessive electric current error |
| Causes: | The input current of the IH PWB is 20A or more (120V) / 10A or more (220-240V) for 100ms continuously. |
| Remedy: | 1 Checking the fuser unit The fuser belt is faulty. Detach the fuser unit and check if the fuser belt is not faulty. If there is any damage, replace the fuser unit. Detaching and reattaching the fuser unit 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB?• IH PWB - Engine PWB Wiring diagram 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 5 Replacing the IH unit The IH unit is faulty. Replace the IH unit. Detaching and reattaching the IH unit 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6770 |
| Description: | IH low power error |
| Causes: | The IH PWB detects 60% or less of the set power value for 120ms after the fuser heating starts. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH unit - IH PWB?• IH PWB - Engine PWB?• IH PWB - Feed PWB?• IH PWB - LVU Wiring diagram 2 Changing the input power The input power is improper. Change the input power. 3 Replacing the LVU The LVU is faulty. Replace the LVU. Detaching and reattaching the LVU 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB 6 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 7 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 8 Replacing the IH unit The IH unit is faulty. (The coil is broken.) Replace the IH unit. Detaching and reattaching the IH unit |
| Error code: | C6900 |
| Description: | Edge fan motor error |
| Causes: | The lock-up was detected for 20s continuously when driving the fan motor. |
| Remedy: | 1 Checking the edge fan motor The connector is not connected properly. The wire is faulty. The fan does not operate as paper size on the MP tray is misdetected. Execute U037 [Fuser Edge] to check the edge fan motor operation. And, check if the paper size on the MP tray is detected properly. If the edge fan motor does not operate properly or the paper size on the MP tray is misdetected, reconnect the connector of the conveying unit (edge fan motor) to the relay connector at the main unit. Maintenanc e Mode List Detaching and reattaching the Right Cover Assy 2 Correcting the connector pins for connecting the right cover (conveying unit) The connector pin deforms at the machine right side (inside the right cover). Correct the deformed connector pin for connecting the right cover (conveying unit) at the machine right side of the main unit (inside the right cover). 3 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Edge fan motor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 4 Replacing the edge fan motor The edge fan motor is faulty. Replace the edge fan motor. Fan Motors Attachable Direction 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C6910 |
| Description: | Engine firmware unexpected error |
| Causes: | 1. The engine stable control continued for one hour. 2. The feed motor does not drive when passing 3s or more while the drum motor or developer motor is driving. 3. The only high voltage remote signal turned on while the drum is stopped. 4. The main charge bias turned off while the developer bias turned on. |
| Remedy: | 1 Resetting the main power The power startup delays. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Checking the engine PWB The engine PWB is not properly attached. Or, the connector is not properly connected. Fix the engine PWB with the screw to make sure the grounding and reinsert the connector on the engine PWB all the way. Detaching and reattaching the engine PWB 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6920 |
| Description: | IH core fan motor error |
| Causes: | The lock-up is detected for 5s continuously while the fan motor is driving. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Execute U037 [IH Coil]. If the fan motor does not properly operate, clean the terminal of the following wire connectors and reconnect the connectors. Replace the wire when it has no continuity.• IH core fan motor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Checking the IH core fan motor The IH core fan motor does not properly operate. Clean the IH core fan motor and remove foreign objects if adhered. If not repaired, replace the IH core fan motor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6950 |
| Description: | IH PWB communication error |
| Causes: | The initial communication between the IH PWB and the engine PWB is not established. (10 times of retries are executed in 30ms interval.) |
| Remedy: | 1 Resetting the main power The power startup delays. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • IH PWB - Engine PWB Wiring diagram 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • LVU - IH PWB Wiring diagram 4 Checking the power supply voltage The abnormal electric noise is mixed in the power supply voltage. Plug the power cord into another wall outlet. 5 Checking the LVU The fuse on the LVU is broken. Check the continuity of the fuse (F002) on the LVU. Then, replace the LVU if there is no continuity. Detaching and reattaching the LVU 6 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. Detaching and reattaching the fuser IH PWB 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6980 |
| Description: | Fuser unit EEPROM error |
| Causes: | The EEPROM in the fuser unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data do not match 8 times continuously. |
| Remedy: | 1 Reinstalling the fuser unit The connector of the fuser unit is not properly connected. Check if the pins of the connector of the fuser unit are not bent, and correct the pins if bent. If there is no problem at the pins, firmly connect the connector. Detaching and reattaching the fuser unit 2 Replacing the fuser unit The fuser unit is faulty. Replace the fuser unit. Detaching and reattaching the fuser unit 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C6990 |
| Description: | Fuser power source destination error |
| Causes: | The information mismatches between the engine backup and the IH PWB. |
| Remedy: | 1 Executing U169 The voltage setting at U169 mismatches the voltage of the IH PWB. Set the destination same as the voltage of the IH PWB at U169. Maintenanc e Mode List 2 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7001 |
| Description: | Toner motor error |
| Causes: | The lock-up is detected 5 times continuously at every 200ms and this continued 30 sets totally (5 times x 30). |
| Remedy: | 1 Replacing the toner container The spiral in the toner container cannot rotate. Check the spiral in the toner container rotates manually. Then check each gear. If it is damaged, replace the toner container. Detaching and reattaching the toner container 2 Checking the toner container drive components The toner container drive parts does not properly operate, or have excessive load. Pull out the toner container and execute U135. Check if the drive gears can rotate smoothly and have no excessive load. If they are faulty, replace them. Executing U135 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Toner motor - Engine PWB Wiring diagram 4 Checking the toner motor The toner motor is faulty. Reattach the toner motor. If not repaired, replace the motor. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7101 |
| Description: | Toner sensor error |
| Causes: | The sensor output value is less than 60 or 944 or more for 3s continuously. |
| Remedy: | 1 Checking the toner sensor The toner sensor is faulty. Check the output value of the toner sensor at U155. Executing U155 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the drive gear The drive gears for the developer unit are damaged. (The spiral cannot rotate.) Replace the drive gears for the developer unit. 5 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7200 |
| Description: | Internal thermistor broken (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) exceeds the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7210 |
| Description: | Internal thermistor short-circuited (For the internal count) |
| Causes: | The output sampling value from the belt skew detection sensor (in-machine thermistor) is less than the reference value. (After the abnormal value is detected, the detected temperature is regarded as 20°C / 68°F.) |
| Remedy: | 1 Executing U139 The belt skew detection sensor is faulty. Execute U139 [Ext/Int] to check the external temperature and humidity display. (Go to the next step.) Executing U139 2 Reinstalling the primary transfer belt unit The primary transfer belt unit is not properly installed. Reinstall the primary transfer belt unit so that the connector is firmly connected. Detaching and reattaching the primary transfer belt unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Primary transfer belt unit - Engine PWB Wiring diagram 4 Primary transfer belt unit replacement The belt skew detection sensor is faulty. Replace the primary transfer belt unit. Detaching and reattaching the primary transfer belt unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7221 |
| Description: | LSU thermistor broken |
| Causes: | The input sampling value of the PD PWB (LSU thermistor) exceeds the reference value. (After the error is detected, the detected temperature is regarded as 23°C / 73°F.) |
| Remedy: | 1 Executing U139 The PD PWB is faulty. Execute U139 [LSU] to check the in-machine temperature around the LSU. (Go to the next step.) Executing U139 2 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • PD PWB (Connects to the APC PWB in the LSU) - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 3 Replacing the LSU The LSU (LSU thermistor) is faulty. Replace the LSU. Detaching and reattaching the LSU 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the engine PWB |
| Error code: | C7231 |
| Description: | LSU thermistor short-circuited |
| Causes: | The input sampling value of the PD PWB (LSU thermistor) is lower than the reference value. (After the error is detected, the detected temperature is regarded as 23 degrees.) |
| Remedy: | 1 Executing U139 The PD PWB is faulty. Execute U139 [LSU] to check the in-machine temperature around the LSU. (Go to the next step.) Executing U139 2 Checking the connection The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • PD PWB (Connects to the APC PWB in the LSU) - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 3 Replacing the LSU The LSU (LSU thermistor) is faulty. Replace the LSU. Detaching and reattaching the LSU 4 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7241 |
| Description: | Developer thermistor broken |
| Causes: | The input sampling value of the toner sensor (developer thermistor) exceeds the reference value. (After the abnormal state is detected, the detection temperature is regarded as 23°C / 73°F.) |
| Remedy: | 1 Executing U139 The toner sensor is faulty. Execute U139 [Developing] to check the in-machine temperature around the developer unit. (Go to the next step.) 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7251 |
| Description: | Developer thermistor short-circuited |
| Causes: | The input sampling value of the toner sensor (developer thermistor) is less than the reference value. (After the abnormal state is detected, the detection temperature is regarded as 23°C / 73°F.) |
| Remedy: | 1 Executing U139 The toner sensor is faulty. Execute U139 [Developing] to check the in-machine temperature around the developer unit. (Go to the next step.) 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the developer unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front PWB - Engine PWB Wiring diagram 4 Replacing the developer unit The developer unit (Toner sensor ) is faulty. Replace the developer unit. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7301 |
| Description: | Toner hopper motor error |
| Causes: | It occurs 15 times continuously that the screw sensor does not detect the pulse for 200ms when driving the toner hopper motor. |
| Remedy: | 1 Checking the toner hopper motor The toner hopper motor is faulty. Execute U135 [Hopper] and check the toner hopper motor operation. (Go to the next step.) Executing U135 2 Checking the toner hopper drive section The toner hopper screw does not properly rotate due to excessive load. (The pulse plate does not rotate.) Rotate the toner hopper screw manually. Then, check if toner is not clogged in the toner hopper, and clean inside the toner hopper if necessary. Detaching and reattaching the inner unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner hopper motor - Front PWB• Screw sensor - Front PWB?• Front PWB - Engine PWB 4 Checking the screw sensor The screw sensor is faulty. Reattach the screw sensor. If not repaired, replace the sensor. 5 Replacing the drive parts The drive transmission from the toner hopper motor is faulty. Reattach the drive gears or the toner hopper motor. If not repaired, replace the parts faulty in operation. Or, replace the inner unit. Detaching and reattaching the inner unit 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7320 |
| Description: | Toner container detection connector error |
| Causes: | Disconnection of the toner container detection connector was detected when closing the toner container cover. |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Container drive unit (RFID PWB) - Feed image PWB Service Manual - Section 8 `PWBs` 2 Checking the container drive unit The connector is not connected properly, or the wire is faulty. If the connector of the wire inside the container drive unit disconnects, reconnect it. If not repaired, replace the container drive unit. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. |
| Error code: | C7401 |
| Description: | Developer unit type mismatch error |
| Causes: | "Unit Identification" of the EEPROM in the developer unit does not match the main unit. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Developer unit - Front PWB• Front PWB - Engine PWB Wiring diagram 2 Replacing the developer unit The developer unit (EEPROM) is faulty. Replace the developer unit. Detaching and reattaching the developer unit 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7420 |
| Description: | Uninstalled primary transfer unit |
| Causes: | 1. Unit identification code does not match. 2. Unit for the other model is installed. |
| Remedy: | 1 Replacing the primary transfer unit The primary transfer unit for other models is installed. Install the primary transfer unit for the applicable models. Detaching and reattaching the Primary Transfer Unit 2 Reinstalling the primary transfer unit The connector of the primary transfer unit is not firmly connected. Reinstall the primary transfer unit so that the connector firmly connects. Detaching and reattaching the Primary Transfer Unit 3 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Transfer connect PWB - Feed image PWB Service Manual - Section 8 `PWBs` 4 Firmware upgrade The firmware is faulty. Reinstall the engine firmware. Firmware Update 5 Replacing the transfer connection PWB The transfer connection PWB is faulty. Replace the transfer connection PWB. 6 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. |
| Error code: | C7470 |
| Description: | Toner collection fan motor 1 error |
| Causes: | The lock-up is detected for 5s continuously while the toner collection fan motor 1 is driving. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner collection fan motor 1 - Engine PWB Wiring diagram 2 Replacing the toner collection box The toner collection fan motor is faulty. Execute U037 [Toner]. If the operation is faulty, replace the toner collection box. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7480 |
| Description: | Toner collection fan motor 2 error |
| Causes: | The lock-up is detected for 5s continuously while the toner collection fan motor 2 is driving. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Toner collection fan motor 2 - Engine PWB Wiring diagram 2 Replacing the toner collection box The toner collection fan motor is faulty. Execute U037 [Toner]. If the operation is faulty, replace the toner collection box. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7490 |
| Description: | Exit fan motor error |
| Causes: | The lock-up was detected for 20s continuously when driving the fan motor. |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Exit fan motor (Fuser drive unit) - Feed drive PWB Service Manual - Section 8 `PWBs` 2 Checking the exit fan motor The fan motor does not rotate properly since it is dirty. Clean the exit fan motor and check if the fan is rotated manually. Then, reattach it. Fan Motors Attachable Direction 3 Replacing the exit fan motor The exit fan motor is faulty. If the exit fan motor does not operate properly when executing U037 [Exit Cooling], replace it. Fan Motors Attachable Direction 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. |
| Error code: | C7601 |
| Description: | Front ID sensor error (For the internal count) |
| Causes: | • Dark potential error: The sensor output value (FrontDarkP and FrontDardS) is less than 0.15V, or more than 0.80V. • Light potential error: FrontBrightS is less than FrontDarkS, or FrontBrightP is less than Front- DarkP+0.5V. |
| Remedy: | 1 Cleaning the front ID sensor The front ID sensor is dirty. Clean the front ID sensor surface. 2 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not properly operate, reattach the cleaning solenoid. Executing U033 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Cleaning solenoid - Relay PWB • Relay PWB - Feed PWB • Feed PWB - Engine PWB Wiring diagram 4 Replacing the cleaning solenoid The cleaning solenoid is faulty. Replace the cleaning solenoid. 5 Checking the front ID sensor The front ID sensor is not properly attached. Reattach the front ID sensor. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •Front ID sensor - Feed PWB • Feed PWB - Engine PWB Wiring diagram 7 Replacing the front D sensor The front ID sensor is faulty. Check if the value of U465 [T7 CTD] is fluctuated before and after Calibration, and replace the front ID sensor if it was not fluctuated (uncalibrated) . Executing U465 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7602 |
| Description: | ID sensor error |
| Causes: | • Dark potential error: The sensor output value (FrontDarkP and FrontDardS) is less than 0.15V, or more than 0.80V. • Light potential error: FrontBrightS is less than FrontDarkS, or FrontBrightP is less than Front- DarkP+0.5V. |
| Remedy: | 1 Cleaning the ID sensor The ID sensor is dirty. Clean the ID sensor surface. 2 Checking the ID sensor shutter The ID sensor shutter does not operate properly. If the ID sensor shutter does not operate properly when executing U033 [ID Sensor] , reattach the cleaning solenoid. Executing U033 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Cleaning solenoid - Relay PWB • Relay PWB - Feed PWB • Feed PWB - Engine PWB Wiring diagram 4 Replacing the cleaning solenoid The cleaning solenoid is faulty. Replace the cleaning solenoid 5 Checking the ID sensor The ID sensor is not properly attached. Reattach the ID sensor. 6 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • ID sensor - Feed PWB 7 Replacing the ID sensor The ID sensor is faulty. Check if the value of "T7 CTD" at U465 fluctuates before and after executing Calibration. If not (no adjustment), replace the ID sensor. Executing U465 8 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the feed PWB The feed PWB is faulty. Replace the feed PWB. 10 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7611 |
| Description: | Bias calibration read value error (Black) |
| Causes: | The ID sensors cannot properly read the patch density on the primary transfer belt when executing Calibration or the color adjustment. |
| Remedy: | 1 Resetting the main power The ID sensor does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 (In case if the printout is light) Checking the developer unit (35ppm or faster models) The developing roller does not contact with the drum. Switch the lock lever up and down and return the developer roller to the setting position. If the developer roller does not return due to the breakage of the lock lever or the failure of the developer roller pressure wire, replace the developer unit. Detaching and reattaching the Developer Unit 3 (In case if the printout is light) Checking the connecting gear of the front cover for the maintenance (25/32PPM models) The developer roller does not contact the drum since it does not properly interlock with the opening and closing operation of the front cover for the maintenance. If the developer roller does not contact the drum even if closing the front cover for the maintenance, reattach the gear connecting to the front cover for the maintenance. 4 (In case if the printout is light) Cleaning / replacing the LSU. The laser does not output properly from the LSU. Or, LSU dustproof glass is dirty. Clean the LSU. If not repaired, replace it. Detaching and reattaching the LSU 5 (In case if the printout is light) Improving the condensation of the drum surface (35ppm or faster models) Condensation on the drum surface Execute the drum refresh. And next, set [On] at U339 [Drum heater] to turn on the drum heater. Adjust/ Maintenanc e Menu (Operation Guide - Section 10) Maintenanc e Mode List 6 Cleaning the ID sensor The ID sensor is dirty. Clean the surface of the front and rear ID sensors. 7 Executing Calibration The last calibration failed. Execute U464 [Calib]. Maintenanc e Mode List 8 Checking the ID sensor shutter The ID sensor shutter does not operate properly. Execute U033 [ID Sensor]. If the ID sensor shutter does not operate properly, reattach the cleaning solenoid. Maintenanc e Mode List 9 Checking the primary transfer unit The primary transfer belt surface is dirty. Clean the surface of the primary transfer belt, or replace the primary transfer unit. Detaching and reattaching the Primary Transfer Unit 10 Checking the ID sensor The ID sensor is not properly attached, or the connector is not properly connected. Reattach the front and rear ID sensors and reconnect the connectors. 11 (When the image is too light) Checking the main high voltage PWB / transfer high voltage PWB Proper current does not flow as the main high voltage PWB or the contact point of the transfer high voltage PWB is faulty. Reattach the main high voltage PWB and the transfer high voltage PWB. 12 (When the image is too light) Checking the drum unit / developer unit / LSU The parts for the drum unit, developer unit and LSU is dirty or worn out. In case if the image is too light, clean the drum unit, developer unit and the LSU. Or, replace them. Maintenanc e parts replacement procedures 13 Firmware upgrade The firmware is not the latest version. Upgrade the firmware to the latest version. Firmware Update 14 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Front ID sensor and Rear ID sensor - Feed drive PWB • Feed drive PWB - Engine PWB Service Manual - Section 8 `PWBs` 15 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. 16 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7800 |
| Description: | Outer thermistor broken (For the internal count) |
| Causes: | The external temperature sensor (external thermistor) cannot be accessed. No response is received from the external thermistor 5 times continuously for 5ms or more when accessing the external thermistor. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Room temperature sensor - Front PWB?• Front PWB - Engine PWB Wiring diagram 2 Replacing the external temperature sensor The external temperature sensor is faulty. Replace the external temperature sensor. 3 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 4 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 5 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7810 |
| Description: | Short-circuited external thermistor • The thermistor input value is 0.5 V or less. |
| Causes: | Poor contact in the connector terminals. Defective humidity sensor. Defective engine PWB |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC13 on the engine PWB and the continuity across the connector terminals. Repair or replace if necessary. Defective humidity sensor. Replace the humidity sensor. Defective engine PWB. Replace the engine PWB. |
| Error code: | C7901 |
| Description: | Drum unit EEPROM error |
| Causes: | The EEPROM in the drum unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously when reading / writing the data. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data stored in the EEPROM in the drum unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the drum unit The drum unit is not properly installed. Reinstall drum unit BK so that the connector firmly connects. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Drum unit - Front PWB • Front PWB - Engine PWB 4 Replacing the dum unit The EEPROM in the drum unit is faulty. Replace the drum unit. Detaching and reattaching the drum unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7911 |
| Description: | Developer unit EEPROM error |
| Causes: | The toner sensor (EEPROM) in the developing unit cannot be accessed. 1. No response from the device is detected for 5s or more 5 times continuously at read/write. 2. Data written in 2 points do not match 8 times continuously. 3. Write data and read data does not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data in the toner sensor (EEPROM) of the developer unit is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Reinstalling the developer unit The developer unit is not properly installed. Reinstall the developer unit so that the connector is firmly connected. Detaching and reattaching the drum unit 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Developer unit - Front PWB • Front PWB - Engine PWB Wiring diagram 4 Replacing the developer unit The toner sensor (EEPROM) of the developer unit is faulty. Replace the developer unit. Detaching and reattaching the developer unit 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the front PWB The front PWB is faulty. Replace the front PWB. 7 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7941 |
| Description: | LSU EEPROM error |
| Causes: | The APC PWB (EEPROM) in the LSU cannot be accessed. 1. Data written at 2 points do not match 8 times continuously. 2. Write data and read data do not match 8 times continuously. |
| Remedy: | 1 Resetting the main power The data of the APC PWB (EEPROM) in the LSU is faulty. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • APC PWB (LSU) - LSU relay PWB • LSU relay PWB - Engine PWB Wiring diagram 3 Replacing the LSU The APC PWB (EEPROM) in the LSU is faulty. Replace the LSU. 4 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 5 Replacing the LSU relay PWB The LSU relay PWB is faulty. Replace the LSU relay PWB. 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C7970 |
| Description: | Weight sensor error |
| Causes: | The condition of the sensor output value was less than the specified value continued for 500ms. |
| Remedy: | 1 Reinstalling the waste toner box The waste toner box is not properly installed. Reinstall the waste toner box into the main unit slowly, and then check if it moves vertically. Replacing the Waste Toner Box (Operation Guide - Section 10) 2 Checking the wire The relay connector (engine PWB and waste toner motor/ weight sensor) is not connected properly or disconnected as excessive tensioning of the wire located at the back side of the waste toner box unit during maintenance work. Realign the wire so that the wire of the relay connector at the waste toner box unit backside is not excessively strained. Then, reconnect the relay connector. Connection of Relay Connector of Waste Toner Box Unit (Section 4 `Detaching and reattaching waste toner box unit) 3 Checking the weight sensor and the actuator The connector is not properly connected. Or, the actuator is not attached properly. Reconnect the connector of the weight sensor. And, reattach the weight sensor actuator and the return spring. 4 Reattaching the weight detection spring The weight detection spring has come off. Detach the waste toner box unit and reattach the weight detection spring. 5 Cleaning around the weight sensor The weight sensor and surrounding parts are dirty. Clean around the weight sensor with an airblower. 6 Executing U155 The calibration of the weight sensor is not executed properly. Execute the waste toner calibration at U155. Maintenanc e Mode List 7 Replacing the waste toner box The waste toner box is faulty. Replace the waste toner box. Replacing the Waste Toner Box (Operation Guide - Section 10) 8 Firmware upgrade The engine firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 9 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Detaching and reattaching the Engine PWB |
| Error code: | C7980 |
| Description: | Waste toner overflow (Waste toner full sensor error) |
| Causes: | The waste toner full sensor detected full (lock) of the waste toner box for 4 times continuously. |
| Remedy: | 1 Checking the waste toner box The waste toner box is full. Detach and reattach the waste toner box and close the waste toner box cover. If the waste toner box is full, replace it. Replacing the Waste Toner Box (Operation Guide - Section 10) 2 Checking the waste toner full sensor The connector is not properly connected. Reconnect the connector of the waste toner full sensor. 3 Cleaning the waste toner box joint section The waste toner is clogged at the waste toner joint section. Clean inside the waste toner box joint section of the main drive unit. Detaching and reattaching the Main Drive Unit 4 Checking the connection The waste toner box joint section and the waste toner box are not properly connected. Realign the wire so that the wire of the relay connector at the waste toner box unit backside is not excessively strained. Then, reconnect the relay connector. After that, reinstall the waste toner box into the main unit. Connection of Relay Connector of Waste Toner Box Unit (Section 4 `Detaching and reattaching waste toner box unit) 5 Firmware upgrade The engine firmware is faulty. Upgrade the engine firmware to the latest version Firmware Update 6 Checking the operation of the weight sensor actuator The weight sensor actuator inside the waste toner box unit does not operate properly. When the voltage from the 2nd pin of connector YC29 on the feed image PWB is not `3.3V (full detection)`, reattach the weight sensor actuator inside the waste toner box unit and check if it operates properly. If not operating properly, replace the waste toner box unit. Detaching and reattaching the Waste Toner Box Unit 7 Replacing the waste toner forwarding unit The waste toner full sensor inside the waste toner forwarding unit misdetects. Replace the waste toner forwarding unit when the voltage from the 2nd pin of connector YC29 on the feed image PWB is `3.3V (full detection)`. Detaching and reattaching the Main Drive Unit 8 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Feed image PWB - Feed drive PWB Service Manual - Section 8 `PWBs` 9 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. 10 Replacing the feed drive PWB The feed drive PWB is faulty. Replace the feed drive PWB. |
| Error code: | C8000 |
| Description: | Fnisher type mismatch problem • Absence of the finisher is detected. |
| Causes: | Different type of the finisher is installed. |
| Remedy: | Install the correct finisher. |
| Error code: | C8010 |
| Description: | Punch motor error 1 Object: 4000-sheet finisher + Punch unit |
| Causes: | 1. The punch home position sensor does not turn on when passing 200ms after driving the punch motor. 2. The pulse plate does not count the specified pulse when passing 300ms after the punch operation starts. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • Punch home position sensor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. 5 Checking the punch home position sensor The punch home position sensor is not properly attached or faulty. Execute U241 [Punch] > [Punch HP]. If the PH home position sensor does not properly operate, reattach it. If not repaired, replace the sensor. Executing U241 6 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 7 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8020 |
| Description: | Punch motor error 2 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position is not aligned within 3s when initializing the home position or standby. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8030 |
| Description: | Punch motor error 3 Object: 4000-sheet finisher + Punch unit |
| Causes: | The home position detection does not turn off within 50ms when initializing the home position. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit is not shifted manually, repair the part that restricts the operation. 2 Checking the punch cam drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch cam drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch motor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the punch motor The punch motor is faulty. Execute U240 [Motor] > [Punch]. If the punch motor does not properly operate, replace it. Executing U240 5 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. Firmware Update 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8040 |
| Description: | Document finisher lower paper conveying belt problem • During initialization, the intermediate tray lower sliding plate is not detected in the home position within 3 s after the belt returns to the home position. JAM87 is indicated the first time this problem occurs. If the problem reoccurs after initialization when the front cover is opened and closed, the problem is in the lower paper conveying belt. • When the intermediate tray lower sliding plate is operated from the home position, the lower paper conveying belt home position sensor does not turn off within 1 s. |
| Causes: | Phase shift of the lower paper conveying belt. Malfunction of the lower paper conveying belt motor. Malfunction of the lower paper conveying belt home position sensor. Loose connection of the lower paper conveying belt home position sensor connector. Incorrect insertion of the intermediate tray. Defective finisher main PWB. |
| Remedy: | Phase shift of the lower paper conveying belt. Correct the phase of the lower paper conveying belt and check for correct operation. Malfunction of the lower paper conveying belt motor. Replace the lower paper conveying belt motor and check for correct operation. Malfunction of the lower paper conveying belt home position sensor. Replace the lower paper conveying belt home position sensor and check for correct operation. Loose connection of the lower paper conveying belt home position sensor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Incorrect insertion of the intermediate tray. Check whether the intermediate tray catches are damaged. Defective finisher main PWB. Replace the finisher main PWB and check for correct operation. |
| Error code: | C8050 |
| Description: | Punch shift motor error 2 Object: 100-sheet staple finisher |
| Causes: | The paper edge cannot be detected if driving the motor by the specified distance (30mm) when detecting the paper edge. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch unit does not move manually, repair the position where restricts the operation. 2 Checking the PH cam drive parts The PH cam drive parts are not attached properly or faulty. Reattach the punch cam drive components. Replace it if not repaired 3 Checking the connection The connector is not properly connected. Or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EPunch shift motor - PH PWB EPaper edge sensor 1,2 - PH PWB EPH PWB- DF PWB 4 Replacing the punch shift motor The punch shift motor is faulty. Execute U240 mMotorn > mPunch Moven Replace the punch shift motor if it does not operate properly. 5 Checking the paper edge sensors 1, 2 Paper edge sensors 1, 2 are not properly attached or faulty. Execute U241 mPunchn > mEdge Face1/2n Reattach the paper edge sensors 1, 2 if they do not operate properly. Replace the paper edge sensors 1, 2 if not repaired. 6 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware to the latest version. 7 Replacing PH PWB PH PWB is faulty. Replace PH PWB. 8 Replacing DF PWB DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. |
| Error code: | C8090 |
| Description: | DF paddle motor error Object: 4000-sheet finisher |
| Causes: | 1. The DF paddle sensor does not turn on when passing 1s during the DF paddle motor drive. 2. The DF paddle sensor does not turn off after driving for 1s while the sensor is on. |
| Remedy: | 1 Checking the DF paddle drive components The DF paddle drive parts are not properly attached or faulty. Reattach the DF paddle drive parts. If not repaired, replace them. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •DF paddle motor - DF main PWB • DF paddle sensor - DF main PWB Wiring diagram 3 Replacing the DF paddle motor The DF paddle motor is faulty. Execute U240 [Motor] > [Beat]. If the DF paddle motor does not properly operate, replace it. Executing U240 4 Replacing the DF paddle sensor The DF paddle sensor is faulty. Execute U241 [Finisher] > [Lead Paddle]. If the DF paddle sensor does not properly operate, replace it. Executing U241 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8100 |
| Description: | DF eject release motor error Object: 4000-sheet finisher |
| Causes: | 1. The DF paper bundle ejection switch does not turn on when passing 1s while driving the DF ejection release motor. 2. The DF paper bundle ejection switch does not turn off when driving it for 1s after it turns on. |
| Remedy: | 1 Checking the DF paper stack eject unit The eject guide in the DF paper stack eject unit is deformed. Correct the DF paper stack eject unit. 2 Checking the DF paper stack eject unit drive components The DF paper bundle ejection unit drive parts are not properly attached or faulty. Reattach the DF paper bundle eject unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF ejection release motor - DF main PWB • DF paper bundle ejection switch - DF main PWB Wiring diagram 4 Replacing the DF eject release motor The DF eject release motor is faulty. Execute U240 [Motor] > [Eject Unlock (HP) ]. If the DF exit release motor does not properly operate, replace it. Executing U240 5 Checking the DF paper stack eject switch The DF paper bundle ejection switch is not properly attached or faulty. Reattach the DF paper bundle ejection switch. If not repaired, replace the switch. 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8110 |
| Description: | DF shift motor 1 error Object: 4000-sheet finisher |
| Causes: | The DF shift sensor 1 does not turn ON or OFF when driving DF shift motor 1 for 3s. |
| Remedy: | 1 Checking the front shift guide The front shift guide is not assembled properly. If the front shift guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front shift guide drive components The front shift guide drive parts are not properly attached or faulty. Reattach the front shift guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. •DF shift motor 1 - DF main PWB • DF shift sensor 1 - DF main PWB 4 Replacing DF shift motor 1 DF shift motor 1 is faulty. Replace DF shift motor 1. 5 Checking DF shift sensor 1 DF shift sensor 1 is not properly attached or faulty. Reattach DF shift sensor 1 and execute U241 [Finisher] > [Shift Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8120 |
| Description: | DF shift motor 2 error Object: 4000-sheet finisher |
| Causes: | The DF shift sensor 2 does not turn ON or OFF when driving DF shift motor 2 for 3s. |
| Remedy: | 1 Checking the rear shift guide The rear shift guide is not assembled properly. If the rear shift guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear shift guide drive components The rear shift guide drive parts are not properly attached or faulty. Reattach the rear shift guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF shift motor 2 - DF main PWB • DF shift sensor 2 - DF main PWB 4 Checking DF shift motor 2 DF shift motor 2 is faulty. Replace DF shift motor 2. 5 Checking DF shift sensor 2 DF shift sensor 2 is not properly attached or faulty. Reattach DF shift sensor 2 and execute U241 [Finisher] > [Shift Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8130 |
| Description: | DF shift release motor error Object: 4000-sheet finisher |
| Causes: | 1. The DF shift release sensor does not turn on when driving the DF shift release motor in the direction of the home position detection for 3s. 2. The DF shift release sensor does not turn off when the DF shift release motor in the direction of the home position detection off for 3s. |
| Remedy: | 1 Checking the rear shift guide The rear shift guide is not assembled properly. If the rear shift guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear shift guide drive components The rear shift guide drive parts are not properly attached or faulty. Reattach the rear shift guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF shift release motor - DF main PWB • DF shift release sensor - DF main PWB 4 Checking the DF shift release motor The DF shift release motor is faulty. Replace the DF shift release motor. 5 Checking the DF shift release sensor The DF shift release sensor is not properly attached or faulty. Reattach the DF shift release sensor and execute U241 [Finisher] > [Shift Unlock HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8140 |
| Description: | Main tray error 1 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 does not turn on when passing 30s while lifting up the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8150 |
| Description: | Main tray error 2 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 1 or 2, or , DF tray upper surface sensor 1 or 2 do not turn on and off when passing 5s when the main tray descends. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 1 - DF main PWB • DF tray sensor 2 - DF main PWB • DF tray upper surface sensor 1 - DF main PWB • DF tray upper surface sensor 2 - DF main PWB Wiring diagram 6 Checking DF tray sensor 1, 2 DF tray sensor 1 or 2 is not properly attached or faulty. Reattach DF tray sensor 1 or 2 and execute U241 [Finisher] > [Tray U-Limit] or [Tray HP2]. If the sensor does not properly operate, replace it. Executing U241 7 Checking DF tray upper side sensor 1, 2 DF tray upper surface sensor 1 or 2 is not properly attached or faulty. Reattach DF tray upper surface sensor 1 or 2 and execute U241 [Finisher] > [Tray Top]. If the sensor does not properly operate, replace it. Executing U241 8 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8160 |
| Description: | DF tray motor error 3 Object: 4000-sheet finisher |
| Causes: | DF tray sensor 4 or 5 does not turn on when passing 60s while descending the main tray. |
| Remedy: | 1 Checking the main tray The main tray is not properly assembled. If the main tray does not move up and down manually, repair the part that restricts the operation. 2 Checking the drive parts The main tray drive parts are not properly attached or faulty. Reattach the main tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF main PWB Wiring diagram 4 Replacing the DF tray motor The DF tray motor is faulty. Execute U240 [Motor] > [Tray]. If the DF tray motor does not properly operate, replace it. Executing U240 5 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray sensor 4 - DF main PWB • DF tray sensor 5 (When installing the Folding Unit) - DF main PWB 6 Checking DF tray sensor 4, 5 DF tray sensor 4 or 5 is not properly attached or faulty. Reattach DF tray sensor 4 or 5 and execute U241 [Finisher] > [Tray L-Limit] or [Tray L-Limit (BL) ]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8170 |
| Description: | DF side registration motor 1 error 1 Object: 4000-sheet finisher |
| Causes: | The home position cannot be detected after passing 3s when relocating to the home position. |
| Remedy: | 1 Checking the front DF side registration guide The front DF side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. 5 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8180 |
| Description: | DF side registration motor 1 error 2 Object: 4000-sheet finisher |
| Causes: | J6810/J6811/J6812 (Front DF side registration jam) was detected 2 times continuously. |
| Remedy: | 1 Checking the front DF side registration guide The front side registration guide is not assembled properly. If the front DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the front DF side registration guide drive components The front DF side registration guide drive parts are not properly attached or faulty. Reattach the front DF side registration guide drive components. 3 Replacing the front DF side registration guide drive components The front DF side registration guide drive components are faulty. Replace the front DF side registration guide drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 1 - DF main PWB • DF side registration sensor 1 - DF main PWB 5 Checking DF side registration motor 1 DF side registration motor 1 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 1 does not properly operate, replace it. Executing U240 6 Checking DF side registration sensor 1 DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8190 |
| Description: | DF side registration motor 2 error 1 Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while executing the operation of returning to the home position. |
| Remedy: | 1 Checking the rear DF side registration guide The rear DF side registration guide is not assembled properly. If the rear DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear DF side registration guide drive components The rear DF side registration guide drive parts are not properly attached or faulty. Reattach the rear DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 2 - DF main PWB • DF side registration sensor 2 - DF main PWB 4 Replacing DF side registration motor 2 DF side registration motor 2 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking DF side registration sensor 2 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8200 |
| Description: | DF side registration motor 2 error 2 Object: 4000-sheet finisher |
| Causes: | J6910 (Rear DF side registration jam) is detected twice continuously. |
| Remedy: | 1 Checking the rear DF side registration guide The rear DF side registration guide is not assembled properly. If the rear DF side registration guide is not shifted manually, repair the part that restricts the operation. 2 Checking the rear DF side registration guide drive components The rear side registration guide drive parts are not properly attached or faulty. Reattach the rear DF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF side registration motor 2 - DF main PWB • DF side registration sensor 2 - DF main PWB Wiring diagram 4 Replacing DF side registration motor 2 DF side registration motor 2 is faulty. Execute U240 [Motor] > [Width Test (A3) ] or [Width Test (LD) ]. If DF side registration motor 2 does not properly operate, replace it. 5 Checking DF side registration sensor 2 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8210 |
| Description: | DF staple motor front/rear error Object: 4000-sheet finisher |
| Causes: | The home position is not detected when passing 3s while returning to the home position at the initial operation. |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple unit is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the DF staple unit drive components The DF staple unit drive parts are not properly attached or faulty. Reattach the DF staple unit drive parts. If not repaired, replace the parts. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple motor - DF main PWB • DF staple sensor - DF main PWB Wiring diagram 4 Replacing the DF staple motor The DF staple motor is faulty. Execute U240 [Motor] > [Staple]. If the DF staple motor does not properly operate, replace the DF staple unit. 5 Checking the DF staple sensor The DF staple sensor is not properly attached or faulty. Reattach the DF staple sensor. Then, replace the DF staple unit if the sensor is not fixed. Detaching and reattaching the DF staple unit 6 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8230 |
| Description: | DF staple motor error Object: 4000-sheet finisher |
| Causes: | J7000 (DF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the DF staple unit The DF staple unit is not assembled properly. If the DF staple cannot operate manually without paper jam, repair the part that restricts the DF staple. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF staple unit - DF main PWB Wiring diagram 3 Replacing the DF staple unit The DF staple unit is faulty. Replace the DF staple unit. Detaching and reattaching the DF staple unit 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8250 |
| Description: | DF main tray error 4 Object: 1000-sheet finisher |
| Causes: | The lock-up detection signal is 0.7V or less for 10s continuously while driving the DF tray motor. |
| Remedy: | 1 Checking the DF tray The DF tray is not assembled properly. If the DF tray does not move up and down manually, repair the position where restricts the operation. 2 Checking the DF tray drive parts The DF tray drive parts are not properly attached, or they are faulty. Reattach the DF tray drive parts. If not repaired, replace them. 3 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF tray motor - DF PWB Service Manual - Section 8 `PWBs` 4 Replacing the DF tray motor The DF tray motor is faulty. Replace the DF tray motor if it does not operate properly when checking the operation at U240. Maintenanc e Mode List 5 Replacing the DF PWB The DF PWB is faulty. Replace the DF PWB. Upgrade the firmware by using the latest upgrade pack immediately after replacing the DF PWB. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8260 |
| Description: | DF middle motor HP detection error Object: 4000-sheet finisher |
| Causes: | J7900 (DF paddle jam) is detected twice continuously. |
| Remedy: | 1 Checking the DF paddle drive components The DF paddle drive parts are not properly attached or faulty. Reattach or replace the DF paddle drive components. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DF middle motor - DF main PWB • DF paddle sensor - DF main PWB Wiring diagram 3 Replacing the DF middle motor The DF middle motor is faulty. Execute U240 [Motor] > [Middle (H) ] or [Middle (L) ]. If the DF middle motor does not properly operate, replace it. Executing U240 4 Checking the DF paddle sensor The DF paddle sensor is not properly attached or faulty. Reattach the DF paddle sensor and execute U241 [Finisher] > [Lead Paddle]. If the sensor does not properly operate, replace it. Executing U241 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8300 |
| Description: | Main program error / Folding unit communication error Object: 4000-sheet finisher + Folding unit |
| Causes: | The main program of the folding unit is faulty when turning the power on. The communication error appears 10 times continuously after finishing the folding unit firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the BF firmware and the DF firmware to the latest version. Firmware Update 3 Checking the BF set switch The BF set switch is not properly attached. Reattach the BF set switch. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 5 Replacing the BF set switch The BF set switch is faulty. Execute U241 [Booklet] > [Set]. If the BF set switch does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8310 |
| Description: | BF side registration motor 2 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 2 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the upper BF side registration guide The upper BF side registration guide is not assembled properly. If the upper BF side registration guide is not shifted manually back and forth, repair the part that restricts the operation. 2 Checking the upper BF side registration guide drive components The upper BF side registration guide drive parts are not properly attached or faulty. Reattach the upper BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 2 - BF main PWB • BF side registration sensor 2 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 2 BF side registration motor 2 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 2 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 2 BF side registration sensor 2 is not properly attached or faulty. Reattach BF side registration sensor 2 and execute U241 [Booklet] > [Width Down HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8320 |
| Description: | BF adjustment motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | At the initialization, turning on of the BF adjustment sensor is not detected after 2.5s passes. |
| Remedy: | 1 Checking the BF shift belt The BF shift belt is not assembled properly. If the BF shift belt is not operated manually, repair the part that restricts the operation. 2 Checking the BF shift belt drive components The BF shift belt drive parts are not properly attached or faulty. Reattach the BF shift belt drive parts. Reattach it if the belt comes off. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF adjustment motor 1, 2 - BF main PWB • BF adjustment sensor 1, 2 - BF main PWB Wiring diagram 4 Replacing BF adjustment motor 1, 2 BF adjustment motor 1 or 2 is faulty. Execute U240 [Booklet] > [Bundle Down] or [Bundle Up]. If BF adjustment motor 1 or 2 does not properly operate, replace them. Executing U240 5 Checking BF adjustment sensor 1, 2 BF adjustment sensor 1 or 2 is not properly attached or faulty. Reattach BF adjustment sensor 1 or 2 and execute U241 [Booklet] > [Width Down HP] or [Bundle Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8330 |
| Description: | BF blade motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The BF blade sensor does not turn on after passing 3s during the initial operation. |
| Remedy: | 1 Checking the BF blade The BF blade is not assembled properly. If the BF blade is not operated manually, repair the part that restricts the operation. 2 Checking the BF blade drive components The BF blade drive parts are not properly attached or faulty. Reattach the BF blade drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF blade motor - BF main PWB • BF blade sensor - BF main PWB Wiring diagram 4 Replacing the BF blade motor The BF blade motor is faulty. Execute U240 [Booklet] > [Blade]. If the BF blade motor does not properly operate, replace it. Executing U240 5 Checking the BF blade sensor The BF blade sensor is faulty. Reattach the BF blade sensor and reinsert the connector. Next, execute U241 [Booklet] > [Blade HP]. If it does not properly operate, replace the sensor. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8340 |
| Description: | BF staple motor error 1 Object: 4000-sheet finisher + Folding unit |
| Causes: | J7600 (BF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The home position is not detected when passing 600ms since the motor starts up.) |
| Remedy: | 1 Checking the BF staple unit The BF staple unit is not assembled properly. If the BF staple unit is not operated manually, repair the part that restricts the operation. 2 Checking the BF staple unit drive components The BF staple unit drive parts are not properly attached or faulty. Reattach the BF staple unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF staple unit - BF main PWB Wiring diagram 4 Replacing the BF staple motor The BF staple motor is faulty. Execute U240 [Booklet] > [Staple]. If the BF staple motor does not properly operate, replace it. Executing U240 5 Replacing the BF staple unit The BF staple unit is faulty. Replace the BF staple unit. 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8350 |
| Description: | BF side registration motor 1 error Object: 4000-sheet finisher + Folding unit |
| Causes: | BF side registration sensor 1 does not turn on after passing 1s during the initial operation. |
| Remedy: | 1 Checking the lower BF side registration guide The lower BF side registration guide is not assembled properly. If the lower BF side registration guide is not operated manually, repair the part that restricts the operation. 2 Checking the lower BF side registration guide drive components The lower BF side registration guide drive parts are not properly attached or faulty. Reattach the lower BF side registration guide drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF side registration motor 1 - BF main PWB • BF side registration sensor 1 - BF main PWB Wiring diagram 4 Replacing BF side registration motor 1 BF side registration motor 1 is faulty. Execute U240 [Booklet] > [Width Test(A3)] or [Width Test(LD)]. If BF side registration motor 1 does not properly operate, replace it. Executing U240 5 Checking BF side registration sensor 1 BF side registration sensor 1 is not properly attached or faulty. Reattach BF side registration sensor 1 and execute U241 [Booklet] > [Width Up HP]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8360 |
| Description: | BF main motor error Object: 4000-sheet finisher + Folding unit |
| Causes: | The lock-up signal was detected for 1s continuously during the motor operation. |
| Remedy: | 1 Checking the BF conveying roller The BF conveying roller is not assembled properly. If the BF conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the BF conveying roller drive parts The BF conveying roller drive parts are not properly attached or faulty. Reattach the BF conveying roller drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main motor - BF main PWB Wiring diagram 4 Replacing the BF main motor The BF main motor is faulty. Execute U240 [Booklet] > [Folding]. If the BF main motor does not properly operate, replace it. Executing U240 5 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8370 |
| Description: | BF staple motor error 2 Object: 4000-sheet finisher + Folding unit |
| Causes: | J7600 (BF staple jam) is detected twice continuously. (Condition of detecting 2nd paper jam: The lock-up detection signal is outputs for 500ms continuously during the motor operation.) |
| Remedy: | 1 Checking the BF staple unit The BF staple unit is not assembled properly. If the BF staple unit is not operated manually, repair the part that restricts the operation. 2 Checking the BF staple unit drive components The BF staple unit drive parts are not properly attached or faulty. Reattach the BF staple unit drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF staple unit - BF main PWB Wiring diagram 4 Replacing the BF staple motor The BF staple motor is faulty. Execute U240 [Booklet] > [Staple]. If the BF staple motor does not properly operate, replace it. Executing U240 5 Replacing the BF staple unit The BF staple unit is faulty. Replace the BF staple unit. 6 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C8380 |
| Description: | BF eject pressure release motor error Object: 4000-sheet finisher with the folding unit |
| Causes: | Operation is not complete when passing 3s after starting up the BF eject pressure release motor |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • The BF eject pressure release motor - DF PWB • The BF eject pressure release HP sensor - DF PWB 2 Repacing the BF eject pressure release motor The BF eject pressure release motor is faulty Execute U240 [Booklet] > [Staple]. If the BF staple motor does not operate properly, replace it. 3 Replacing the BF eject pressure release HP sensor The BF eject pressure release HP sensor is faulty Replace the BF eject pressure release HP sensor 4 Replacing the BF PWB The BF PWB is faulty. Replace the BF PWB. |
| Error code: | C8390 |
| Description: | BF paddle motor error Object: 4000-sheet finisher with the folding unit |
| Causes: | Operation is not complete when passing 250ms after starting up the BF paddle motor |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. EBF eject pressure release motor - BF PWB EBF eject pressure release HP sensor - BF PWB 2 Replacing the BF paddle motor The BF paddle motor is faulty Execute U240 mBookletn > mPaddlen. Replace the BF paddle motor if it does not operate properly. 3 Replacing the BF paddle HP sensor The BF paddleHP sensor is faulty Replace the BF paddle HP sensor 4 Replacing the BF PWB The BF PWB is faulty. Replace the BF PWB. |
| Error code: | C8400 |
| Description: | BF conveying tray motor error Object: 4000-sheet finisher with the folding unit |
| Causes: | Lock signal is detected for 100ms when passing 1s after starting the BF conveying tray motor drive |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. ETthe BF conveying tray motor - BF PWB 2 Replacing the BF conveying tray motor Tthe BF conveying tray motor is faulty Execute U240 mBookletn > mFeed Trayn. Replace the BF conveying tray motor if it does not operate properly. 3 Replacing the BF PWB The BF PWB is faulty. Replace the BF PWB. |
| Error code: | C8410 |
| Description: | Punch slide motor error 1 Object: 4000-sheet finisher + Punch unit |
| Causes: | The punch slide sensor does not turn on after the home position shifts 30mm. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch slide section is not shifted manually forwardbackward, repair the part that restricts the operation. 2 Checking the punch drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch slide motor - PH main PWB • Punch slide sensor - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the PH slide motor The punch slide motor is faulty. Execute U240 [Motor] > [Punch Move]. If the punch slide motor does not properly operate, replace it. 5 Checking the punch slide sensor The punch slide sensor is not properly attached or faulty. Reattach the punch slide sensor. If not repaired, replace it. 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8420 |
| Description: | Punch slide motor error 2 Object: 4000-sheet finisher + Punch unit |
| Causes: | The paper edge cannot be detected even if shifting 30mm when detecting the paper edge. |
| Remedy: | 1 Checking the punch unit The punch unit is not assembled properly. If the punch slide section is not shifted manually forwardbackward, repair the part that restricts the operation. 2 Checking the punch drive components The punch cam drive parts are not properly attached or faulty. Reattach the punch drive parts. If not repaired, replace them. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • Punch slide motor - PH main PWB • PH paper edge sensor 1, 2 - PH main PWB • PH main PWB - DF main PWB Wiring diagram 4 Replacing the PH slide motor The punch slide motor is faulty. Execute U240 [Motor] > [Punch Move]. If the punch slide motor does not properly operate, replace it. 5 Checking the PH paper edge sensor 1, 2 PH paper edge sensor 1 or 2 is not properly attached or faulty. Reattach PH paper edge sensor 1 or 2 and execute U241 [Punch] > [Edge Face1] or [Edge Face2]. If the sensor does not properly operate, replace it. Executing U241 6 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 7 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8430 |
| Description: | Main program error (Punch unit) / Punch unit communication error Object: 4000-sheet finisher + Punch unit |
| Causes: | The main program of the punch unit is faulty when turning the power on. The communication error appears 10 times continuously after finishing the punch unit firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the PH firmware and the DF firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • PH main PWB - DF main PWB 4 Replacing the PH main PWB The PH main PWB is faulty. Replace the PH main PWB. 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8500 |
| Description: | Main program error (Mail Box) / Mail Box communication error Object: 4000-sheet finisher + Mail box |
| Causes: | The main program of the mail box is faulty when turning the power on. The communication error appears 10 times continuously after finishing the mail box firmware version reading. |
| Remedy: | 1 Resetting the main power The operation program does not properly operate. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the MB firmware and the DF firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB main PWB - DF main PWB 4 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. 5 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. |
| Error code: | C8510 |
| Description: | MB conveying motor error 1 Object: 4000-sheet finisher + Mail box |
| Causes: | The MB home position sensor does not turn on after passing 5s during the initial operation. |
| Remedy: | 1 Checking the MB conveying roller The MB conveying roller is not assembled properly. If the MB conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB conveying motor - MB main PWB • MB home position sensor - MB main PWBPWB Wiring diagram 3 Replacing the MB conveying motor The MB conveying motor is faulty. Execute U240 [Mail Box] > [Conv]. If the MB conveying motor does not properly operate, replace it. 4 Checking the MB home position sensor The MB home position sensor is not properly attached or faulty. Reattach the MB home position sensor and execute U241 [Mail Box] > [Motor HP]. If the sensor does not properly operate, replace it. Executing U241 5 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. |
| Error code: | C8520 |
| Description: | MB conveying motor error 2 Object: 4000-sheet finisher + Mail box |
| Causes: | The MB home position sensor does not turn off after passing 1s during the standby operation. |
| Remedy: | 1 Checking the MB conveying roller The MB conveying roller is not assembled properly. If the MB conveying roller is not rotated manually, repair the part that restricts the operation. 2 Checking the MB conveying roller drive components The MB conveying roller drive parts are not properly attached or faulty. Reattach the MB conveying roller drive components. 3 Replacing the MB conveying roller drive components The MB conveying roller drive components are faulty. Replace the MB conveying roller drive components. 4 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • MB conveying motor - MB main PWB • MB home position sensor - MB main PWBPWB 5 Replacing the MB conveying motor The MB conveying motor is faulty. Execute U240 [Mail Box] > [Conv]. If the MB conveying motor does not properly operate, replace it. Executing U240 6 Checking the MB home position sensor The MB home position sensor is not properly attached or faulty. Reattach the MB home position sensor and execute U241 [Mail Box] > [Motor HP]. If the sensor does not properly operate, replace it. Executing U241 7 Replacing the MB main PWB The MB main PWB is faulty. Replace the MB main PWB. |
| Error code: | C8600 |
| Description: | DF adjusting release motor error Object: 100-sheet staple finisher |
| Causes: | Change of DF adjusting release HP sensor was not detected when driving the DF adjusting release motor for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF adjusting release motor - DF PWB EDF adjusting release HP sensor - DF PWB 2 Replacing the DF adjusting release motor The DF adjusting release motor is faulty. Execute U240 mMotorn > mMatch Pressure] Replace the DF adjusting release motor if it does not operate properly. 3 Replacing the adjusting release HP sensor The DF adjusting release HP sensor is faulty. Execute U241 mFinishern > mMatch Coro HP] Replace the DF adjusting release HP sensor if it does not operate properly. 4 Replacing BF PWB BF PWB is faulty. Replace BF PWB. |
| Error code: | C8610 |
| Description: | DF pull-in guide release motor error Object: 100-sheet staple finisher |
| Causes: | Change of DF pull-in guide release HP sensor was not detected when driving the DF pull-in guide release motor for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF pull-in guide release motor - DF PWB EDF pull-in guide release HP sensor - DF PWB 2 Replacing the DF pull-in guide release motor The DF pull-in guide release motor is faulty. Execute U240 mMotorn > mBeatn Replace the DF adjusting release motor if it does not operate properly. 3 Replacing the DF pull-in guide release HP sensor The DF pull-in guide release HP sensor is faulty. Execute U241 mFinishern > mRear Beat HPn Replace the DF adjusting release HP sensor if it does not operate properly. 4 Replacing BF PWB BF PWB is faulty. Replace BF PWB. |
| Error code: | C8620 |
| Description: | DF pull-in pulley pressure release motor error Object: 100-sheet staple finisher |
| Causes: | Change of DF pull-in pulley pressure release HP sensor was not detected when driving the DF pull-in pulley pressure release motor for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF pull-in guide release HP sensor - DF PWB EDF pull-in guide release HP sensor - DF PWB 2 Replacing the DF pull-in pulley pressure release motor The DF pull-in pulley pressure release motor is faulty. Execute U240 mMotorn > mPull Pressuren Replace the DF pull-in pulley pressure release motor if it does not operate properly. 3 Replacing the DF pull-in guide release HP sensor The DF pull-in pulley pressure release HP sensor is faulty. Execute U241 mFinishern > mPull Coro HPn Replace the DF pull-in pulley pressure release HP sensor if it does not properly operate. 4 Replacing BF PWB BF PWB is faulty. Replace BF PWB. |
| Error code: | C8630 |
| Description: | Eject pressure release motor error Object: 100-sheet staple finisher |
| Causes: | Change of the eject pressure release HP switch was not detected when driving the eject pressure release motor for 3s in the direction of HP sensor change. |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF eject pressure release motor - DF PWB EDF eject pressure release HP sensor - DF PWB 2 Replacing the DF eject pressure release motor The DF eject release motor is faulty. Execute U240 mMotorn > mEject Unlockn Replace the DF eject release motor if it does not operate properly. 3 Checking the DF eject pressure release sensor The DF eject pressure release sensor is not attached properly or faulty. Reattach the DF eject pressure release HP sensor and execute U241 mFinishern > mEject Press HPn. Replace the DF eject pressure release HP sensor if it does not operate properly. 4 Replacing the DF PWB The DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8640 |
| Description: | DF side registration motor 1 error Object: 100-sheet staple finisher |
| Causes: | Change of DF side registration HP sensor 1 was not detected when driving the DF side registration motor 1 for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF side registration motor 1 - DF PWB EDF side registration HP sensor 1 - DF PWB 2 Replacing DF side registration motor 1 The connector is not properly connected. Or the wire is faulty. Execute U240 mMotorn > mWidth Testn Replace DF side registration motor 1 if it does not operate properly. 3 Checking DF side registration HP sensor DF side registration motor 1 is faulty. DF side registration sensor 1 is not properly attached or faulty. Reattach DF side registration sensor 1 and execute U241 [Finisher] > [Width Front HP]. Replace DF side registration HP sensor 1 if it does not operate properly. 4 Replacing the DF PWB The DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8650 |
| Description: | DF side registration motor 2 error Object: 100-sheet staple finisher |
| Causes: | Change of DF side registration HP sensor 2 was not detected when driving the DF side registration motor 2 for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF side registration motor 2 - DF PWB EDF side registration HP sensor 2 - DF PWB 2 Replacing DF side registration motor 2 The DF side registration motor 2 is faulty. Execute U240 mMotorn > mWidth Testn Replace DF side registration motor 2 if it does not operate properly. 3 Checking the DF side registration HP sensor 1 DF side registration sensor 2 is not properly attached or faulty. Reattach DF side registration sensor 2 and execute U241 [Finisher] > [Width Tail HP]. Replace DF side registration motor 2 if it does not operate properly. 4 Replacing the DF PWB The DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8700 |
| Description: | DF bundle eject motor 1 error Object: 100-sheet staple finisher |
| Causes: | Change of DF bundle eject HP sensor 1 was not detected when driving the DF bundle eject motor 1 for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF bundle eject motor 1 - DF PWB EDF bundle eject HP sensor 1 - DF PWB 2 Replacing DF bundle eject motor 1 The bundle eject motor 1 is faulty. Execute U240 mMotorn > mBundle Upn Replace the DF bundle eject motor 1 if it does not operate properly. 3 Checking the DF paper stack eject sensor The DF bundle eject HP sensor 1 is not attached properly or faulty. DF PWB is faulty. Reattach the DF bundle eject HP sensor 1 and execute U241 mFinishern > mBundle Eject HP1n. Replace the DF bundle eject HP sensor 1 if it does not properly operate. 4 Replacing the DF PWB The DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8710 |
| Description: | DF bundle eject motor 2 error Object: 100-sheet staple finisher |
| Causes: | Change of DF bundle eject HP sensor 2 was not detected when driving the DF bundle eject motor 2 for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF bundle eject motor 2 - DF PWB EDF bundle eject HP sensor 2 - DF PWB 2 Replacing DF bundle eject motor 2 The bundle eject motor 2 is faulty. Execute U240 mMotorn > mBundle Upn Replace the DF bundle eject motor 2 if it does not operate properly. 3 Checking the DF bundle eject HP sensor 2 The DF bundle eject HP sensor 2 is not attached properly or faulty. Reattach the DF bundle eject HP sensor 2 and execute U241 mFinishern > mBundle Eject HP2n. Replace the DF bundle eject HP sensor 2 if it does not properly operate. 4 Replacing the DF PWB The DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8720 |
| Description: | DF eject paddle motor error Object: 100-sheet staple finisher |
| Causes: | Change of DF eject paddle HP sensor was not detected when driving the DF eject paddle motor for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF eject paddle motor - DF PWB EDF eject paddle HP sensor - DF PWB 2 Replacing the DF paddle motor The DF paddle motor is faulty. Execute U240 mMotorn > mTray Eject Paddlen Replace the DF eject paddle motor if it does not operate properly. 3 Checking the DF eject sensor The DF eject paddle sensor is not properly attached or faulty. Reattach the DF eject paddle HP sensor and execute U241 [Finisher] > [Eject Paddle HP]. Replace the DF eject paddle HP sensor if it does not operate properly. 4 Replacing the DF PWB The DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8730 |
| Description: | DF eject paper trailing edge holding motor error Object: 100-sheet staple finisher |
| Causes: | Change of DF eject paper trailing edge holding HP sensor was not detected when driving the DF eject paper trailing edge holding motor for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF eject paper trailing edge holding motor - DF PWB EDF eject paper trailing edge holding HP sensor - DF PWB 2 Replacing the DF eject paper trailing edge holding motor The DF eject paper trailing edge holding motor is faulty. Execute U240 mMotorn > mPress Papern Replace the DF eject paper trailing edge holding motor if it does not operate properly. 3 Checking the DF eject paper trailing edge holding HP sensor DF eject paper holding sensor is not properly attached or faulty. Reattach the DF exit paddle HP sensor and execute U241 [Finisher] > [Press Paper HP]. Replace the DF eject paper trailing edge holding HP sensor if it does not operate properly. 4 Replacing the DF PWB The DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8740 |
| Description: | DF eject support guide motor error Object: 100-sheet staple finisher |
| Causes: | Change of DF eject support guide HP sensor was not detected when driving the DF support guide motor for 3s in the direction of HP sensor change |
| Remedy: | 1 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the terminals of the wire connector and reinstall it. If there is no continuity, replace the wire. EDF eject holding guide motor - DF PWB EDF eject holding guide HP sensor - DF PWB 2 Replacing the DF eject support guide motor DF eject support guide motor is faulty. Execute U240 mMotorn > mEject Guiden Replace the DF eject support guide motor if it does not operate properly. 3 Replacing the DF eject support guide HP sensor DF bundle support guide sensor is not attached properly or faulty. DF PWB is faulty. Reattach the DF eject support guide HP sensor and execute U241 mFinishern > mEject Guiden. Replace the DF eject paper trailing edge holding HP sensor if it does not operate properly. 4 Replacing the DF PWB The DF PWB is faulty. Replace DF PWB. After replacing the PWB, upgrade the firmware to the latest version. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8800 |
| Description: | Main program error (DF) / Engine - DF communication error Object: 4000-sheet finisher |
| Causes: | The main program is faulty when turning on the power. The Engine -DF communication error is detected 10 times continuously. |
| Remedy: | 1 Resetting the main power The program does not start up properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Firmware upgrade The firmware is not the latest version. Upgrade the DP firmware to the latest version. Firmware Update 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 4 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 6 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C8810 |
| Description: | DF-SubCPU communication error Object: 100-sheet staple finisher |
| Causes: | Communication with SubCPU fails 3 times continuously. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the DF firmware to the latest version. 2 Replacing the DF PWB The DF PWB is faulty. Replace the DF PWB. Upgrade the firmware by using the latest upgrade pack immediately after replacing the DF PWB. Detaching and reattaching the DF PWB Firmware Update |
| Error code: | C8900 |
| Description: | DF backup error Object: 4000-sheet finisher (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reinsert the connectors. Replace the wire when it has no continuity. • DF main PWB - Engine PWB Wiring diagram 2 Replacing the DF main PWB The DF main PWB is faulty. Replace the DF main PWB. Detaching and reattaching the DF main PWB |
| Error code: | C8930 |
| Description: | BF unit backup error Object: 4000-sheet finisher + Folding unit (For the internal count) |
| Causes: | The writing data and the reading data mismatch 3 times continuously. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • BF main PWB - DF main PWB Wiring diagram 2 Replacing the BF main PWB The BF main PWB is faulty. Replace the BF main PWB. |
| Error code: | C9000 |
| Description: | Main program error (DP) / Document Processor communication error |
| Causes: | The document processor cannot be communicated. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the scanner firmware and the DP firmware to the latest version. Firmware Update 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DP main PWB - Engine PWB Wiring diagram 3 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 4 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C9040 |
| Description: | DP lift motor ascend error |
| Causes: | The DF lift upper limit sensor does not detect ON when passing 1500 pulses 5 times or more while the DP lift motor drives to ascend. |
| Remedy: | 1 Checking the DP original feed lift plate The DP original feed lift plate is not properly attached. If the DP original feed lift plate does not move up and down manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DP lift motor - DP main PWB • DP lift upper limit sensor - DP main PWB Wiring diagram 3 Replacing the DP lift motor The DP lift motor is faulty. Execute U243 [Lift Motor]. If the DP lift motor does not properly operate, replace the motor. 4 Checking the DP lift upper limit sensor The DP lift upper limit sensor is not properly attached or faulty. Reattach the DP lift upper limit sensor and execute U244 [Lift U-Limit]. If the sensor does not properly operate, replace it. Executing U244 5 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. |
| Error code: | C9050 |
| Description: | DP lift motor descend error |
| Causes: | The DF lift lower limit sensor does not detect ON when passing 1500 pulses while the DP lift motor drives to descend. (3 times of retries) |
| Remedy: | 1 Checking the DP original feed lift plate The DP original feed lift plate is not properly attached. If the DP original feed lift plate does not move up and down manually, repair the part that restricts the operation. 2 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DP lift motor - DP main PWB • DP lift lower limit sensor - DP main PWB Wiring diagram 3 Replacing the DP lift motor The DP lift motor is faulty. Execute U243 [Lift Motor]. If the DP lift motor does not properly operate, replace the motor. 4 Checking the DP lift lower limit sensor The DP lift lower limit sensor is not properly attached or faulty. Reattach the DP lift lower limit sensor and execute U244 [Lift L-Limit]. If the sensor does not properly operate, replace it. Executing U244 5 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. |
| Error code: | C9060 |
| Description: | DP EEPROM error |
| Causes: | Read data and write data to the EEPROM do not match 3 times continuously. |
| Remedy: | 1 Checking the EEPROM The EEPROM is not properly installed. Reattach the EEPROM on the DP main PWB. 2 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. Detaching and reattaching the DP main PWB 3 Replacing the EEPROM The EEPROM is faulty. Replace the EEPROM on the DP main PWB and execute U411. |
| Error code: | C9070 |
| Description: | DP - SHD communication error |
| Causes: | The communication error between the DP main PWB and the DPSHD PWB was detected during communication. |
| Remedy: | 1 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DPSHD PWB - DP main PWB Wiring diagram 2 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. 3 Replacing the DP main PWB The DP main PWB is faulty. Replace the DP main PWB. |
| Error code: | C9080 |
| Description: | LED failure detection (For the internal count) |
| Causes: | After 4 blocks of the LED lamps of the DPCIS are lit when turning the power on, the acquired peak value of some blocks is at the reference value or less. (The light level detected by the CIS is not enough.) |
| Remedy: | 1 Checking the LED lamp The LED lamp of the DPCIS does not light. 0 Executing U203 2 Checking the DPSHD PWB The DPSHD PWB is not properly connected. Reconnect the DPSHD PWB to the DPCIS. 3 Checking the connection The connector is not properly connected. Or, the wire is faulty. Clean the terminal of the following wire connectors and reconnect the connectors. If there is no continuity, replace the wire. • DPSHD PWB - DP main PWB Wiring diagram 4 Executing U411 DP scanning is not properly adjusted. Execute U411 [DP FD (ChartB) ] and [DP FD (ChartA)]. Executing U411 5 Replacing the DPCIS The DPCIS is faulty. Replace the DPCIS, and then execute U091 and U411. Detaching and reattaching the DPCIS 6 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. |
| Error code: | C9180 |
| Description: | DP feed-shift motor error Object: Mechanically reversed DP with the DP feed belt Remarks: When detecting the DP feed-shift motor error (C9180) (up to 2 times), display J9002. |
| Causes: | HP can`t be detected even after the retrying process for the HP detection of the DP feed-shift guide for 3 times continuously. * HP detection of the DP feed-shift guide: When the DP feed-shift motor moves to HP, if HP can`t be detected even driving the DP feed-shift motor for 1 round, the retry is done. |
| Remedy: | 1 Removing the original The original accordion jam in the guide between the DP reversing tray and the DP registration roller (The position is not visible when the DP upper cover is opened) Remove the original which is stuck in the guide between the DP reversing tray and DP registration roller. 2 Cleaning the original conveying guide. Sticky foreign objects adhere to the original conveying guide Clean the original conveying guide. 3 Resetting the main power The DP feed-shift motor is not controlled correctly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 4 Checking the DP feed-shift motor The DP feed-shift motor is not rotated correctly. Or, there is an excess load. After removing the DP feed-shift motor and repair it by rotating the drive section manually, reattach it. 5 Checking the connection The connector is not connected properly, or the wire is faulty. Clean the connector terminal of the wire and reconnect. If there is no continuity, replace the wire. EDP feed-shift motor - DP PWB EDP feed-shift sensor - DP PWB Service Manual - Section 8 `PWBs` 6 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 7 Replacing the DP feed-shift motor The DP feed-shift motor is faulty. Replace the DP feed-shift motor. 8 Checking the DP feed-shift sensor The DP feed-shift sensor is not attached properly or faulty. Reattach the DP feed-shift sensor. If not repaired, replace it. 9 Replacing the DP PWB The DP PWB is faulty. Replace the DP PWB. Detaching and reattaching the DF PWB |
| Error code: | C9500 |
| Description: | Image processing circuit error (Scanner) |
| Remedy: | 1 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. If the FFC terminal section is deformed or the FFC is broken, replace the FFC. • Engine PWB - Main PWB Wiring diagram 2 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the main PWB 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. |
| Error code: | C9510 |
| Description: | Image processing circuit error (DP) |
| Remedy: | 1 Checking the DP relay PWB The DP relay PWB is not properly attached. Reattach the DP relay PWB. 2 Checking the connection The connector is not properly connected. Or, the SATA cable is faulty. 0 Wiring diagram 3 Replacing the DPSHD PWB The DPSHD PWB is faulty. Replace the DPSHD PWB. 4 Replacing the DP relay PWB The DP relay PWB is faulty. Replace the DP relay PWB. 5 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | C9540 |
| Description: | Backup data error |
| Causes: | When multiple parts are replaced at the same time, the internal data is changed and it interferes with the machine operation. Consequently, the main unit cannot recover. |
| Remedy: | 1 Checking the PWB Multiple PWBs were replaced at the same time. Recover to the original, if 2 or more of the following related parts were replaced at the same time. • Related parts: Memory, each PWB 2 Checking the unit Multiple units were replaced at the same time. Be sure not to perform the following works at the same time when the memory or each PWB is replaced. • Replacing the drum unit or the developer unit • Relocating the drum units to other colorspositioninsideamainunit` |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F021 |
| Description: | System memory error (RAM reading/writing error or ASIC memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the main PWB ASIC when the main unit starts up. |
| Remedy: | 1 Resetting the main power The main PWB does not properly start up. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F022 |
| Description: | System memory error (RAM reading/writing error or ASIC memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the DP relay PWB ASIC when the main unit starts up. |
| Remedy: | 1 Resetting the main power The main PWB does not properly start up. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. 3 Checking the DP relay PWB The DP relay PWB is not properly connected or attached. Reattach the DP relay PWB and secure it with the screws. If not repaired, replace the DP relay PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F041 |
| Description: | Over than available setting number tray detection error |
| Causes: | Over than available setting number tray is installed. |
| Remedy: | Remove the available setting number tray. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F051 |
| Description: | Scanner engine program error |
| Causes: | The scanner program cannot start up |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The scanner engine RAM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the SSD The SSD is not properly attached. Reattach the SSD. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F052 |
| Description: | Panel engine program error |
| Causes: | The panel program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the panel firmware to the latest version. Firmware Update 2 Resetting the main power The panel RAM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the connection The connector is not properly connected or the wire is faulty. Clean the connectors on the operation panel main PWB and reinsert the wire connectors. If there is no continuity, replace the wire. Wiring diagram 4 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F14E |
| Description: | Error detection at FAX control section |
| Causes: | If the communication between the main PWB and the FAX is interrupted, the signal is resent but it continues to wait until necessary signal comes in and locks up. |
| Remedy: | 1 Resetting the main power As the power reset was performed instantly, an error occurred in the communication between the controller and the FAX. Turn off the power switch and the main power switch. After 5 seconds, turn on the main power switch and the power switch. 2 Checking the connection The FAX PWB is not connected properly. Clean the following connection terminals and reconnect the FAX PWB. EMain PWB - FAX PWB Service Manual - Section 8 "PWBs" FAX Installation Guide 3 Firmware upgrade The firmware is not the latest version. Upgrade the fax firmware to the latest version. Firmware Update 4 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide |
| Error code: | F186 |
| Description: | Finisher Interface Error |
| Causes: | • Finisher Control Board • Finisher Interconnect Cable • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Finisher Interconnect Cable • Finisher connections Is there any damage? Replace any damaged parts. Go to Step 2. 2 Check all the pins of the Finisher Interconnect Cable for continuity. Is the cable conductive? Go to Step 3. Replace the cable. 3 Check all the pins of the OPTIF Harness for continuity. Is the harness conductive? Go to Step 4. Replace the OPTIF harness. 4 Replace the Finisher Control Board. Does the error persists? Replace the Engine Control Board Complete. |
| Error code: | F278 |
| Description: | Secondary power source error |
| Causes: | The operation became unstable since the primary supply power dropped out temporarily and recovered. |
| Remedy: | 1 Resetting the main power The power reset was performed immediately. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected or the wire is faulty. Clean the connectors on the LVU and reinsert the wire connectors. If there is no continuity, replace the wire. 3 Replacing the LVU The LVU is faulty. Replace the LVU. |
