Kyocera TASKalfa 8001i
Рейтинг
Модули
Paper Conveying Section 1-3
COOLING SECTION
Paper Conveying Section 1-1
Drive Section & Electrical Components(DP)
Paper Conveying Section 3
Paper Deck Covers
Covers 1
OPERATION PANEL SECTION
Paper Cassettes
Paper Deck Drive Section
Fuser Section
Paper Deck Feed Section 1
Drive Section 1
Bridge Section 1
Bridge Section 2
Inner Section 2
Paper Deck Frames
Covers 3
ADF 1
Inner Section 1
Paper Deck Feed Section 3
PAPER FEED SECTION 2
Bridge Section 3
FRAME L
Paper Conveying Section(DP)
PAPER FEED
Paper Deck Electrical Components
ELECTRICAL COMPONENTS 2
Paper Feed Section 2(DP)
Paper Deck Feed Section 2
Scanner & Laser Scanner Section
Covers(DP)
Covers 2
Job Separator Section
Paper Deck Cassettes
Frames(DP)
Paper Feed Section 1
Exit Section
FRAMES
Electrical Components 1
Paper Feed Section 1(DP)
Paper Conveying Section 2
CASSETTE ASSEMBLY
Image Formation & Developer Section
Operation Arm Section
DRIVE SECTION 2
Table Assy(DP)
Paper Conveying Section 1-2
Детали COOLING SECTION
| Деталь: | GUIDE TRANSFER REAR |
| Парткод: | 302LF22230 |
| Деталь: | FILM GUIDE REAR |
| Парткод: | 302LF22260 |
| Деталь: | HOLDER TRANSFER REAR |
| Парткод: | 302LF22240 |
| Деталь: | STATIC-ELIMINATOR TRANSFER |
| Парткод: | 302LF22250 |
| Деталь: | SPACER PRESS TRANSFER |
| Парткод: | 302LF22380 |
| Деталь: | PARTS MOTOR-BL W10 SP |
| Парткод: | 302LC94291 |
| Деталь: | PLATE TRANSFER DRIVE |
| Парткод: | 302LF22120 |
| Деталь: | STAY TRANSFER |
| Парткод: | 302LF22220 |
| Деталь: | FRAME TRANSFER |
| Парткод: | 302LF22091 |
| Деталь: | Plate Bias |
| Парткод: | 302LF22310 |
| Деталь: | SHEET CONTACT HV |
| Парткод: | 302LF22620 |
| Деталь: | SPRING TRANSFER |
| Парткод: | 302LF22280 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 302LF22010 |
| Деталь: | PLATE HOLDER REAR |
| Парткод: | 302LF22290 |
| Деталь: | ROLLER TRANSFER DRIVE |
| Парткод: | 302LF22020 |
| Деталь: | BELT TRANSFER |
| Парткод: | 302LF22060 |
| Деталь: | ROLLER TRANSFER IDLE |
| Парткод: | 302LF22030 |
| Деталь: | PLATE HOLDER FRONT |
| Парткод: | 302LF22320 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GEAR Z30R |
| Парткод: | 302LF22100 |
| Деталь: | BEARING MR106ZZ |
| Парткод: | 7BE006103431H01 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | VARISTOR TC ASSY |
| Парткод: | 302FZ01310 |
| Деталь: | GEAR Z31R-Z42R |
| Парткод: | 302LF22210 |
| Деталь: | GEAR Z21L-Z39L |
| Парткод: | 302LF22110 |
| Деталь: | GUIDE TRANSFER FRONT B |
| Парткод: | 302LF22080 |
| Деталь: | SPRING TRANS GUIDE |
| Парткод: | 302LF22570 |
| Деталь: | COVER MOTOR |
| Парткод: | 302LF22200 |
| Деталь: | BUSH TRANSFER |
| Парткод: | 302LF22400 |
| Деталь: | COVER TRANSFER |
| Парткод: | 302LF22470 |
| Деталь: | HOLDER TRANSFER REAR |
| Парткод: | 302LF22150 |
| Деталь: | RETAINER TRANSFER FRONT |
| Парткод: | 302LF22450 |
| Деталь: | RETAINER TRANSFER REAR |
| Парткод: | 302LF22460 |
| Деталь: | HOLDER TRANSFER FRONT |
| Парткод: | 302LF22140 |
| Деталь: | PARTS CONVEYING H UNIT SP |
| Парткод: | 302N794080 |
| Деталь: | PARTS BELT ASSY SP |
| Парткод: | 302LF94060 |
| Деталь: | 2LF33420 |
| Парткод: | 302LF33420 |
| Деталь: | 2GR44080 |
| Парткод: | 302GR44080 |
| Цена: | 2 800 ₽ |
| Деталь: | 2K933580 |
| Парткод: | 302K933580 |
| Деталь: | 2K933151 |
| Парткод: | 302K933151 |
| Деталь: | 2LC33510 |
| Парткод: | 302LC33510 |
| Деталь: | 2K933161 |
| Парткод: | 302K933161 |
| Деталь: | YZ010230 |
| Парткод: | 7YZM610001++H01 |
| Деталь: | YZ010250 |
| Парткод: | 7YZM610003++H01 |
| Деталь: | 2HN44010 |
| Парткод: | 302HN44010 |
| Деталь: | 2K933281 |
| Парткод: | 302K933281 |
| Деталь: | 2K946640 |
| Парткод: | 302K946640 |
| Деталь: | 2LC31511 |
| Парткод: | 302LC31511 |
| Деталь: | 2K994350 |
| Парткод: | 302K994350 |
| Деталь: | 2LC33471 |
| Парткод: | 302LC33471 |
| Деталь: | 2HG02450 |
| Парткод: | 302HG02450 |
| Деталь: | 2K933190 |
| Парткод: | 302K933190 |
| Деталь: | YZ010240 |
| Парткод: | 7YZM610002++H01 |
| Деталь: | 2K933560 |
| Парткод: | 302K933560 |
| Деталь: | 2K933572 |
| Парткод: | 302K933572 |
| Деталь: | 2LF33050 |
| Парткод: | 302LF33050 |
| Деталь: | 2LF33060 |
| Парткод: | 302LF33060 |
| Деталь: | 2LF33090 |
| Парткод: | 302LF33090 |
| Деталь: | 2LF33430 |
| Парткод: | 302LF33430 |
| Деталь: | 2K931080 |
| Парткод: | 302K931080 |
| Деталь: | 2N733130 |
| Парткод: | 302N733130 |
| Деталь: | 2LF02441 |
| Парткод: | 302LF02441 |
| Деталь: | 2LF02450 |
| Парткод: | 302LF02450 |
| Деталь: | 2LF02460 |
| Парткод: | 302LF02460 |
| Деталь: | 2K933010 |
| Парткод: | 302K933010 |
| Деталь: | 2K933040 |
| Парткод: | 302K933040 |
| Деталь: | 2LC94380 |
| Парткод: | 302LC94380 |
| Деталь: | 2H733430 |
| Парткод: | 302H733430 |
| Деталь: | 2LF33540 |
| Парткод: | 302LF33540 |
| Деталь: | 2LF33201 |
| Парткод: | 302LF33201 |
| Деталь: | 2N733180 |
| Парткод: | 302N733180 |
| Деталь: | 2N733190 |
| Парткод: | 302N733190 |
| Деталь: | 2N733230 |
| Парткод: | 302N733230 |
| Деталь: | 2N733240 |
| Парткод: | 302N733240 |
| Деталь: | 2N733110 |
| Парткод: | 302N733110 |
| Деталь: | 2K933271 |
| Парткод: | 302K933271 |
| Деталь: | 2LF33131 |
| Парткод: | 302LF33131 |
| Деталь: | 2LF33141 |
| Парткод: | 302LF33141 |
| Деталь: | 2LF33460 |
| Парткод: | 302LF33460 |
| Деталь: | 2LF33150 |
| Парткод: | 302LF33150 |
| Деталь: | 2LF33110 |
| Парткод: | 302LF33110 |
| Деталь: | 2LF33120 |
| Парткод: | 302LF33120 |
| Деталь: | 2FZ94380 |
| Парткод: | 302FZ94380 |
| Деталь: | 2LF46151 |
| Парткод: | 302LF46151 |
| Деталь: | 2N733010 |
| Парткод: | 302N733010 |
| Деталь: | 2N733250 |
| Парткод: | 302N733250 |
| Деталь: | 2LF33571 |
| Парткод: | 302LF33571 |
| Деталь: | 2LF33560 |
| Парткод: | 302LF33560 |
| Деталь: | 2LF33550 |
| Парткод: | 302LF33550 |
| Деталь: | 2LF33410 |
| Парткод: | 302LF33410 |
| Деталь: | 2LF33440 |
| Парткод: | 302LF33440 |
| Деталь: | 2LF33450 |
| Парткод: | 302LF33450 |
| Деталь: | 2LF33510 |
| Парткод: | 302LF33510 |
| Деталь: | 2LF33520 |
| Парткод: | 302LF33520 |
| Деталь: | 2K933241 |
| Парткод: | 302K933241 |
| Деталь: | 2LF33630 |
| Парткод: | 302LF33630 |
| Деталь: | 2LF33640 |
| Парткод: | 302LF33640 |
| Деталь: | 2LF33650 |
| Парткод: | 302LF33650 |
| Деталь: | 2K933250 |
| Парткод: | 302K933250 |
| Деталь: | 3LL02330 |
| Парткод: | 303LL02330 |
| Деталь: | 2LF33310 |
| Парткод: | 302LF33310 |
| Деталь: | 2FB25330 |
| Парткод: | 302FB25330 |
| Деталь: | 2LF33300 |
| Парткод: | 302LF33300 |
| Деталь: | 2FZ33170 |
| Парткод: | 302FZ33170 |
| Деталь: | 2LF33320 |
| Парткод: | 302LF33320 |
| Деталь: | 2LF33330 |
| Парткод: | 302LF33330 |
| Деталь: | 2LF33160 |
| Парткод: | 302LF33160 |
| Деталь: | 2LF33500 |
| Парткод: | 302LF33500 |
| Деталь: | 2LF46170 |
| Парткод: | 302LF46170 |
| Деталь: | 2LF46210 |
| Парткод: | 302LF46210 |
| Деталь: | 2LF46220 |
| Парткод: | 302LF46220 |
| Деталь: | 2K994090 |
| Парткод: | 302K994090 |
| Деталь: | FRAME CONVEYING FRONT |
| Парткод: | 302N729010 |
| Деталь: | SHAFT CONVEYING HOOK UP |
| Парткод: | 302K929100 |
| Деталь: | LEVER COVER RIGHT |
| Парткод: | 302K929090 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PLATE CONVEYING TOP |
| Парткод: | 302K929051 |
| Деталь: | PLATE CONVEYING LOW |
| Парткод: | 302K929040 |
| Деталь: | FRAME CONVEYING RIGHT |
| Парткод: | 302N729020 |
| Деталь: | ARM HOOK F |
| Парткод: | 302K929400 |
| Деталь: | HOOK CONVEYING UP |
| Парткод: | 302K929120 |
| Деталь: | SPRING HOOK UP |
| Парткод: | 302K929190 |
| Деталь: | HOOK CONVEYING LOW F |
| Парткод: | 302K929140 |
| Деталь: | SPRING HOOK |
| Парткод: | 3HL07240 |
| Деталь: | CAM HOOK FRONT |
| Парткод: | 302K929170 |
| Деталь: | PIN CONVEYING F |
| Парткод: | 302K929630 |
| Деталь: | GUIDE UNIT F |
| Парткод: | 302LF29040 |
| Деталь: | ARM HOOK R |
| Парткод: | 302N729060 |
| Деталь: | HOOK CONVEYING LOW R |
| Парткод: | 302K929150 |
| Деталь: | CAM HOOK REAR |
| Парткод: | 302K929160 |
| Деталь: | PLATE CONVEYING UPPER |
| Парткод: | 302N729030 |
| Деталь: | Cover arm |
| Парткод: | 302N729050 |
| Деталь: | GEAR Z30R-Z27L |
| Парткод: | 302K929240 |
| Деталь: | PLATE JOINT |
| Парткод: | 302K929600 |
| Деталь: | GUIDE GEAR |
| Парткод: | 302K929610 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | MOUNT DU DRIVE |
| Парткод: | 302K929062 |
| Деталь: | SPRING LEVER EF |
| Парткод: | 302F902180 |
| Деталь: | GUIDE UNIT R |
| Парткод: | 302K929580 |
| Деталь: | PARTS PWB JUNCTION ASSY SP |
| Парткод: | 302K994201 |
| Деталь: | SPRING HOLDER PULLEY |
| Парткод: | 302K924770 |
| Деталь: | PULLEY MPT BYPASS |
| Парткод: | 302FZ07020 |
| Деталь: | PLATE EARTH DU |
| Парткод: | 302K929690 |
| Деталь: | PARTS ROLLER DU UP SP |
| Парткод: | 302K994491 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302HG12310 |
| Деталь: | GUIDE DU LOWER A |
| Парткод: | 302N729440 |
| Деталь: | GEAR Z43R |
| Парткод: | 302K929740 |
| Деталь: | MOUNT MOTOR DU UP |
| Парткод: | 302K929730 |
| Деталь: | BUSH DU EW |
| Парткод: | 302K924830 |
| Деталь: | PARTS MOTOR PM FEED SP |
| Парткод: | 302K994300 |
| Деталь: | COVER CLUTCH A |
| Парткод: | 302K929540 |
| Деталь: | FILM GUIDE DU A |
| Парткод: | 302K929790 |
| Деталь: | FILM GUIDE DU B |
| Парткод: | 302K929800 |
| Деталь: | GUIDE DU UPPER A |
| Парткод: | 302K929431 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | ACTUATOR DU A |
| Парткод: | 302K929470 |
| Деталь: | SPRING-TORSION SWITCHBACK |
| Парткод: | 302K928190 |
| Деталь: | PARTS,FAN COOLING CONVEYING SP |
| Парткод: | 302FZ94420 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | WIRE DU UPPER |
| Парткод: | 302LC46240 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING-COMPRESSION DU UP |
| Парткод: | 302K929780 |
| Деталь: | COVER RIGHT GUIDE |
| Парткод: | 302K929490 |
| Деталь: | COVER WIRE |
| Парткод: | 302K929750 |
| Деталь: | PIN CONVEYING R |
| Парткод: | 302K929640 |
| Деталь: | HOLDER DRAWER |
| Парткод: | 302K924390 |
| Деталь: | PLATE DRAWER |
| Парткод: | 302K929620 |
| Деталь: | WIRE CONVEYING |
| Парткод: | 302LF46521 |
| Деталь: | COVER INNER CONVEYING A |
| Парткод: | 302N729040 |
| Деталь: | WIRE MPF JOINT |
| Парткод: | 302LC46480 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | WIRE CONVEYING MOTOR |
| Парткод: | 302LF46AL0 |
| Деталь: | PARTS FAN COOLING 50 SP |
| Парткод: | 302LC94320 |
| Деталь: | DUCT CONVEYING RIGHT |
| Парткод: | 302LF33390 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302LC94380 |
| Деталь: | DUCT CONVEYING LEFT |
| Парткод: | 302LF33380 |
| Деталь: | SEAL DUCT CONVEYING |
| Парткод: | 302LF33400 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SPONGE DUCT CONVEYING |
| Парткод: | 302LF33610 |
| Деталь: | PARTS CONVEYING H UNIT SP |
| Парткод: | 302N794080 |
| Деталь: | PARTS PWB DRIVER ASSY SP |
| Парткод: | 303P694010 |
| Деталь: | PARTS MOTOR CONVEYING SP |
| Парткод: | 303M494040 |
| Деталь: | PARTS MOTOR DU SP |
| Парткод: | 302KY94070 |
| Деталь: | GEAR EXIT Z43 Z20 |
| Парткод: | 303M431440 |
| Деталь: | PARTS MOTOR ROTARY GUIDE |
| Парткод: | 302H794310 |
| Деталь: | GEAR 20/65 IDLE |
| Парткод: | 303H622331 |
| Деталь: | PARTS GEAR Z42 SP |
| Парткод: | 303M494120 |
| Деталь: | PARTS GEAR JOINT Z20 Z65 SP |
| Парткод: | 303M494130 |
| Деталь: | GEAR 20 JOINT |
| Парткод: | 3H622160 |
| Деталь: | BAND,RSG-130-V0(KITAGAWA) |
| Парткод: | M21AH010 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | GEAR Z35 |
| Парткод: | 303M431050 |
| Деталь: | GEAR Z20 P48 |
| Парткод: | 303M431060 |
| Деталь: | GEAR Z30 Z23 |
| Парткод: | 303M431090 |
| Деталь: | GEAR Z25 Z19 |
| Парткод: | 303M431400 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR Z22 ONEWAY |
| Парткод: | 303M431040 |
| Деталь: | GR 33 CONV |
| Парткод: | 3HK22040 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | WIRE INTERFACE |
| Парткод: | 303M446010 |
| Деталь: | PARTS MOTOR REGISTRATION SP |
| Парткод: | 303M494181 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | TORQUE-LIMITER 1000 |
| Парткод: | 303M406160 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SPRING, CONVEYING HOOK |
| Парткод: | 2BC16470 |
| Деталь: | JOINT RETARD DRIVE |
| Парткод: | 302K906180 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | MOUNT PF DRIVE |
| Парткод: | 303M431013 |
| Деталь: | PLATE PF DRIVE |
| Парткод: | 303M431021 |
| Деталь: | MOUNT LOOP DRIVE |
| Парткод: | 303M431200 |
| Деталь: | BELT 146 |
| Парткод: | 303M431120 |
| Деталь: | MOUNT LIFT DRIVE |
| Парткод: | 303M431141 |
| Деталь: | COVER LIFT DRIVE |
| Парткод: | 303M431150 |
| Деталь: | PIN LIFT DRIVE A |
| Парткод: | 303M431230 |
| Деталь: | MOUNT CONV MOTOR B |
| Парткод: | 303M431311 |
| Деталь: | SHAFT PF DRIVE C |
| Парткод: | 303M431360 |
| Деталь: | SHAFT PF DRIVE F |
| Парткод: | 303M431390 |
| Деталь: | MOUNT INTERLOCK SW |
| Парткод: | 303M431410 |
| Деталь: | WIRE MOTOR1 |
| Парткод: | 303M446050 |
| Деталь: | WIRE FRONT |
| Парткод: | 303M446080 |
| Деталь: | MOUNT CONV MOTOR A |
| Парткод: | 303M431300 |
| Деталь: | BELT 60S1.5M161 |
| Парткод: | 303M431290 |
| Деталь: | PIN,HOOK FULCRUM |
| Парткод: | 3CZ02230 |
| Деталь: | GEAR Z43 Z22 |
| Парткод: | 303M431101 |
| Деталь: | PLATE EARTH CONV MOTOR |
| Парткод: | 303M431420 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 2FB07330 |
| Деталь: | PARTS PWB MPF SIZE ASSY SP |
| Парткод: | 302K994620 |
| Деталь: | TRAY MPF A |
| Парткод: | 302K908030 |
| Деталь: | TRAY MPF B |
| Парткод: | 302K908040 |
| Деталь: | TRAY MPF C |
| Парткод: | 302K908050 |
| Деталь: | TRAY MPF D |
| Парткод: | 302K908060 |
| Деталь: | RACK CURSOR MPF |
| Парткод: | 302K908120 |
| Деталь: | ACTUATOR SIZE DETECTION |
| Парткод: | 302K908211 |
| Деталь: | TERMINAL PAPER SIZE |
| Парткод: | 3HL06110 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | LABEL MPF CAUTION A |
| Парткод: | 302LC34061 |
| Деталь: | LABEL MPF PAPER LIMIT |
| Парткод: | 302LC34080 |
| Деталь: | SPRING-COMPRESSION LIFT |
| Парткод: | 302K908200 |
| Деталь: | SHAFT LIFT MPF |
| Парткод: | 302K908190 |
| Деталь: | ARM LIFT A |
| Парткод: | 302K908130 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | ARM LIFT B |
| Парткод: | 302K908140 |
| Деталь: | HOLDER MPF TABLE |
| Парткод: | 302K908650 |
| Деталь: | SPRING PF |
| Парткод: | 303LL07471 |
| Деталь: | SPRING-TORSION SIZE DETECTION |
| Парткод: | 302K908220 |
| Деталь: | HOLDER SIZE DETECTION |
| Парткод: | 302K908580 |
| Деталь: | GUIDE WIRE TRAY |
| Парткод: | 302K908160 |
| Деталь: | WIRE MPF SIZE DETECTION |
| Парткод: | 302K946600 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | BASE LIFT |
| Парткод: | 302K908080 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302F909210 |
| Деталь: | WIRE MPF TRAY |
| Парткод: | 302K946380 |
| Деталь: | SPRING DRUM JOINT |
| Парткод: | 302H712650 |
| Деталь: | CURSOR MPF R |
| Парткод: | 302K908110 |
| Деталь: | CURSOR MPF F |
| Парткод: | 302K908100 |
| Деталь: | COVER CURSOR |
| Парткод: | 302K908090 |
| Деталь: | IDLE GEAR 40,TONER SUPPLY |
| Парткод: | 65815060 |
| Деталь: | SEAL FRAME ISU |
| Парткод: | 302K917100 |
| Деталь: | LABEL MPF SIZE INDICATOR IN |
| Парткод: | 302LC34100 |
| Деталь: | PARTS MPT TRAY UNIT SP |
| Парткод: | 302K994051 |
| Деталь: | COVER DECK REAR |
| Парткод: | 302K904131 |
| Деталь: | COVER MOUNT SLIDER |
| Парткод: | 303NF04130 |
| Деталь: | SHAFT FEED LOW HOOK |
| Парткод: | 302K906681 |
| Деталь: | HANDLE FEED LOW |
| Парткод: | 302K906660 |
| Деталь: | HOOK FEED LOW |
| Парткод: | 302K906670 |
| Деталь: | COVER FEED LOW |
| Парткод: | 303NJ06010 |
| Деталь: | SPRING LID |
| Парткод: | 302FZ20021 |
| Деталь: | LEVER SW |
| Парткод: | 303NF06170 |
| Деталь: | GUIDE VERTICAL |
| Парткод: | 303NF06141 |
| Деталь: | STRAP |
| Парткод: | 303NJ06050 |
| Деталь: | COVER RIGHT LOWER M |
| Парткод: | 302K904162 |
| Деталь: | FOOT |
| Парткод: | 302FZ02600 |
| Деталь: | PLATE FULCRUM |
| Парткод: | 303NF02330 |
| Деталь: | PARTS VERTICAL CONVEYING UNIT SP |
| Парткод: | 303NF94030 |
| Деталь: | COVER INNER FEED F |
| Парткод: | 302K904243 |
| Деталь: | COVER RIGHT LOWER F |
| Парткод: | 302K904092 |
| Деталь: | COVER RIGHT MIDDLE R |
| Парткод: | 302LC04064 |
| Деталь: | COVER RIGHT LOWER R |
| Парткод: | 302K904103 |
| Деталь: | COVER INTERFACE |
| Парткод: | 303NF04121 |
| Деталь: | Cover Handle |
| Парткод: | 302LC04280 |
| Деталь: | COVER MAIN SWITCH |
| Парткод: | 302LC04290 |
| Деталь: | LABEL SW CAUTION EN |
| Парткод: | 302LC34620 |
| Деталь: | COVER FRONT UPPER |
| Парткод: | 302K904011 |
| Деталь: | STOPPER CONTAINER |
| Парткод: | 302K904320 |
| Деталь: | PLATE FRONT COVER |
| Парткод: | 302K904510 |
| Деталь: | STRAP FRONT COVER |
| Парткод: | 302K904560 |
| Деталь: | PLATE MAGNET |
| Парткод: | 2FB04270 |
| Деталь: | EMBLEM |
| Парткод: | 302LC04272 |
| Деталь: | SHEET EMBLEM 8001 |
| Парткод: | 302N704010 |
| Деталь: | SHEET EMBLEM 6501 |
| Парткод: | 302N804010 |
| Деталь: | LABEL TONER OPERATION |
| Парткод: | 302LF34020 |
| Деталь: | COVER WASTE BOTTLE |
| Парткод: | 302K904040 |
| Деталь: | COVER INNER CASSETTE L |
| Парткод: | 302K904250 |
| Деталь: | COVER LEFT LOWER |
| Парткод: | 302K904073 |
| Деталь: | PARTS,HUMIDITY SENSOR,SP |
| Парткод: | 302H094300 |
| Деталь: | COVER HUMIDITY SENSOR |
| Парткод: | 302LC02710 |
| Деталь: | COVER FRONT MIDDLE |
| Парткод: | 302K904021 |
| Деталь: | DUCT FRONT COVER |
| Парткод: | 302K904170 |
| Деталь: | RETAINER M4 |
| Парткод: | 3CY06030 |
| Деталь: | SPONGE FRONT COVER A |
| Парткод: | 302LF04090 |
| Деталь: | LID RIGHT COVER |
| Парткод: | 302K904390 |
| Деталь: | STRAP |
| Парткод: | 303NJ06050 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302K904620 |
| Деталь: | LEVER BOTTLE COVER |
| Парткод: | 302K904650 |
| Деталь: | PLATE BYPASS HOLD |
| Парткод: | 2BL06890 |
| Деталь: | SPONGE FRONT COVER B |
| Парткод: | 302LF04100 |
| Деталь: | COVER WIRE FUSER |
| Парткод: | 302K939521 |
| Деталь: | COVER INNER CASSETTE R |
| Парткод: | 302K904262 |
| Деталь: | SHEET HUMIDITY SENSOR |
| Парткод: | 302K902980 |
| Деталь: | GUIDE WIRE FEED LOW |
| Парткод: | 302LC06210 |
| Деталь: | WIRE FRONT LOW |
| Парткод: | 302LF46230 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | LABEL SW CAUTION SET A |
| Парткод: | 302LC34630 |
| Деталь: | COVER OPERATION B |
| Парткод: | 302N205030 |
| Деталь: | PARTS PWB OPERATION ASSY SP |
| Парткод: | 302N294160 |
| Деталь: | PARTS PWB OPERATION LED ASSY SP |
| Парткод: | 302N294170 |
| Деталь: | PARTS LCD OPERATION SP |
| Парткод: | 302N294140 |
| Деталь: | PARTS PWB PANEL MAIN ASSY SP |
| Парткод: | 302N294150 |
| Деталь: | COVER OPERATION A |
| Парткод: | 302N205020 |
| Деталь: | KEY 10 |
| Парткод: | 302LC05050 |
| Деталь: | KEY FUNCTION |
| Парткод: | 302N405070 |
| Деталь: | KEY HOME |
| Парткод: | 302N405100 |
| Деталь: | KEY START B |
| Парткод: | 302N205190 |
| Деталь: | KEY STOP |
| Парткод: | 302LC05100 |
| Деталь: | KEY RESET |
| Парткод: | 302LC05110 |
| Деталь: | SPONGE LCD A |
| Парткод: | 302N205060 |
| Деталь: | LID OPERATION SHEET A |
| Парткод: | 302LC05150 |
| Деталь: | LID OPERATION SHEET B |
| Парткод: | 302LC05160 |
| Деталь: | SPONGE LCD B |
| Парткод: | 302N205070 |
| Деталь: | LENS LED |
| Парткод: | 302N205040 |
| Деталь: | PARTS SPEAKER SP |
| Парткод: | 302LC94370 |
| Деталь: | FILM WIRE LCD |
| Парткод: | 302N205080 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | LID OPERATION REAR |
| Парткод: | 302K905030 |
| Деталь: | HOLDER LED |
| Парткод: | 302N205050 |
| Деталь: | PLATE LCD |
| Парткод: | 302N205150 |
| Деталь: | FILM FEED C |
| Парткод: | 302FB09410 |
| Деталь: | TAPE SHIELDING LCD |
| Парткод: | 302N205160 |
| Деталь: | PARTS TABLET OPERATION SP |
| Парткод: | 302N294130 |
| Деталь: | KEY MENU |
| Парткод: | 302N405080 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | KEY POWER |
| Парткод: | 302N405090 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | LABEL LED EN |
| Парткод: | 302K905610 |
| Деталь: | KEY DISPLAY |
| Парткод: | 302N405110 |
| Деталь: | KEY RIGHT SIDE |
| Парткод: | 302N405120 |
| Деталь: | WIRE FFC KEY PWB |
| Парткод: | 302N246050 |
| Деталь: | WIRE LED PWB |
| Парткод: | 302N246090 |
| Деталь: | MOUNT MAIN PWB |
| Парткод: | 302N205010 |
| Деталь: | SPRING USB HOLD |
| Парткод: | 302K905900 |
| Деталь: | WIRE USB HOST |
| Парткод: | 302K946801 |
| Деталь: | WIRE PANEL JOINT |
| Парткод: | 302N246030 |
| Деталь: | PANEL OPERATION |
| Парткод: | 302N905010 |
| Деталь: | ACCESS.BAND |
| Парткод: | 7YZM410002++H01 |
| Деталь: | SHEET OPERATION EN |
| Парткод: | 302N705510 |
| Деталь: | SHEET OPERATION KDA EN |
| Парткод: | 302N705630 |
| Деталь: | LABEL LED SET A |
| Парткод: | 302N205670 |
| Деталь: | SHEET OPERATION DE |
| Парткод: | 302N705530 |
| Деталь: | SHEET OPERATION FR |
| Парткод: | 302N705540 |
| Деталь: | SHEET OPERATION TL |
| Парткод: | 302N705550 |
| Деталь: | SHEET OPERATION ES |
| Парткод: | 302N705560 |
| Деталь: | SHEET OPERATION PT |
| Парткод: | 302N705570 |
| Деталь: | SHEET OPERATION NL |
| Парткод: | 302N705580 |
| Деталь: | SHEET OPERATION RU |
| Парткод: | 302N705590 |
| Деталь: | SHEET OPERATION KDA FR |
| Парткод: | 302N705640 |
| Деталь: | SHEET OPERATION KDA ES |
| Парткод: | 302N705650 |
| Деталь: | SHEET OPERATION KDA PT |
| Парткод: | 302N705660 |
| Деталь: | WIRE PANEL DATA |
| Парткод: | 302N446010 |
| Деталь: | OPERATION UNIT |
| Парткод: | 302N794050 |
| Деталь: | GEAR GUIDE SIDE |
| Парткод: | 302BM07410 |
| Деталь: | RACK CURSOR |
| Парткод: | 302K909060 |
| Деталь: | PARTS GEAR CURSOR SP |
| Парткод: | 302K994550 |
| Деталь: | ACTUATOR PAPER LEVEL DETECTION |
| Парткод: | 302K909270 |
| Деталь: | LABEL PAPER SIZE A |
| Парткод: | 302K934011 |
| Деталь: | LABEL PAPER SIZE B |
| Парткод: | 302K934021 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09991 |
| Деталь: | LABEL CASSETTE PAPER MAX |
| Парткод: | 302K934090 |
| Деталь: | LABEL CASSETTE CURSOR LOCK |
| Парткод: | 302K934100 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CASSETTE BASE |
| Парткод: | 302N209011 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | ARM SIZE DETECTION |
| Парткод: | 302N209030 |
| Деталь: | LABEL CASSETTE OPERATION |
| Парткод: | 302K934030 |
| Деталь: | SPRING CASSETTE EARTH |
| Парткод: | 302N209040 |
| Деталь: | PLATE WORK |
| Парткод: | 302K909090 |
| Деталь: | SHAFT WORK PLATE |
| Парткод: | 302K909190 |
| Деталь: | CAP TURN PLATE |
| Парткод: | 302K909140 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | 302H728100 |
| Деталь: | LEVER SIDE SW |
| Парткод: | 302K909251 |
| Деталь: | SPRING DU |
| Парткод: | 302FZ29131 |
| Деталь: | CAM CURSOR RAIL |
| Парткод: | 302K909100 |
| Деталь: | CURSOR REAR |
| Парткод: | 302K909041 |
| Деталь: | RAIL CURSOR |
| Парткод: | 302K909021 |
| Деталь: | LEVER CURSOR LOCK REAR |
| Парткод: | 302K909121 |
| Деталь: | LOCK REAR CURSOR |
| Парткод: | 302K909151 |
| Деталь: | SHAFT CURSOR GEAR |
| Парткод: | 302K909131 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | CURSOR FRONT |
| Парткод: | 302K909031 |
| Деталь: | LEVER CURSOR |
| Парткод: | 302K909050 |
| Деталь: | SPRING LOOP SOLENOID |
| Парткод: | 303JC02050 |
| Деталь: | CURSOR END |
| Парткод: | 302N209020 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302K909260 |
| Деталь: | LABEL SET PAPER |
| Парткод: | 302K934040 |
| Деталь: | LABEL CASSETTE NUMBER 1 |
| Парткод: | 302K934050 |
| Деталь: | LABEL CASSETTE NUMBER 2 |
| Парткод: | 302K934060 |
| Деталь: | EMBLEM CASSETTE |
| Парткод: | 302K904200 |
| Деталь: | COVER CASSETTE |
| Парткод: | 302N204180 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 302K904190 |
| Деталь: | SHEET CASSETTE PAPER SIZE A |
| Парткод: | 302K934700 |
| Деталь: | SHEET CASSETTE PAPER SIZE B |
| Парткод: | 302K934710 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-A |
| Парткод: | 302K934730 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-B |
| Парткод: | 302K934740 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-C |
| Парткод: | 302K934750 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-D |
| Парткод: | 302K934760 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-E |
| Парткод: | 302K934770 |
| Деталь: | CT-8706 |
| Парткод: | 302N293010 |
| Деталь: | PARTS PLATE PAPER BOTTOM UNIT SP |
| Парткод: | 302K994C20 |
| Деталь: | PARTS COVER CASSETTE ASSY SP |
| Парткод: | 302N294040 |
| Деталь: | HOUSING MAIN DRIVE |
| Парткод: | 303NF31010 |
| Деталь: | SHAFT CLUTCH CONVEYING A |
| Парткод: | 303NF31090 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | SHAFT FEED DRIVE B |
| Парткод: | 303NF31110 |
| Деталь: | GEAR Z20RD |
| Парткод: | 303NF31080 |
| Деталь: | COUPLING DRIVE |
| Парткод: | 302K931530 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | COUPLING DRIVE |
| Парткод: | 303NF31180 |
| Деталь: | SPRING DRIVE |
| Парткод: | 303NF31170 |
| Деталь: | GEAR Z20R |
| Парткод: | 303NF31070 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 303NF31030 |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 303NJ31120 |
| Деталь: | BRACKET GEAR CHANGE |
| Парткод: | 303NJ31031 |
| Деталь: | GEAR Z60R |
| Парткод: | 303NJ31060 |
| Деталь: | GEAR Z40R-Z34L |
| Парткод: | 303NJ31140 |
| Деталь: | GEAR Z51L Z60L |
| Парткод: | 303NF31040 |
| Деталь: | GEAR Z36R |
| Парткод: | 303NF31160 |
| Деталь: | GEAR Z75L-Z32L |
| Парткод: | 303NJ31080 |
| Деталь: | GEAR Z28R |
| Парткод: | 303NJ31130 |
| Деталь: | GEAR Z27L MAIN |
| Парткод: | 302JZ31170 |
| Деталь: | GEAR Z56L-Z40R |
| Парткод: | 303NJ31070 |
| Деталь: | GEAR Z34L |
| Парткод: | 303NF31150 |
| Деталь: | PLATE DRIVE L |
| Парткод: | 303NF31020 |
| Деталь: | PARTS MOTOR-BL W30 SP |
| Парткод: | 302K994331 |
| Деталь: | GEAR Z35L |
| Парткод: | 303NF31050 |
| Деталь: | GEAR Z35R |
| Парткод: | 303NF31060 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | WIRE CLUTCH |
| Парткод: | 303NF46070 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 303NF31130 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | GUIDE WIRE FRONT PWB |
| Парткод: | 302LF39050 |
| Деталь: | PARTS DRIVE UNIT SP |
| Парткод: | 303NF94040 |
| Деталь: | PARTS DRIVE SUB UNIT SP |
| Парткод: | 303NF94050 |
| Деталь: | FK-6701 |
| Парткод: | 302N793030 |
| Деталь: | FK-6702 |
| Парткод: | 302N793040 |
| Деталь: | FK-6708IH |
| Парткод: | 302N793070 |
| Деталь: | FK-6709IH |
| Парткод: | 302N793080 |
| Деталь: | GEAR Z28 FEED |
| Парткод: | 302N406170 |
| Деталь: | PULLEY FEED |
| Парткод: | 302N406030 |
| Цена: | 440 ₽ |
| Деталь: | GEAR Z32 FEED OW |
| Парткод: | 302N406100 |
| Деталь: | GEAR Z32 PICKUP |
| Парткод: | 302N406110 |
| Деталь: | SPRING DU |
| Парткод: | 302F925780 |
| Деталь: | PLATE FRAME UPPER |
| Парткод: | 302N406010 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 302K906510 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302K906321 |
| Деталь: | GEAR PRIMARY FEED IDLE Z20R Z16L |
| Парткод: | 302K906230 |
| Деталь: | PARTS ROLLER ASSIST SP |
| Парткод: | 303NJ94050 |
| Деталь: | GEAR FEED DRIVE Z20L |
| Парткод: | 302K906240 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR PRIMARY FEED Z17L OW |
| Парткод: | 303NJ06040 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302K994580 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | PULLEY RETARD |
| Парткод: | 302N406040 |
| Цена: | 450 ₽ |
| Деталь: | LEVER RETARD LOCK |
| Парткод: | 302N406160 |
| Деталь: | PLATE RETARD ADJUST |
| Парткод: | 302K906420 |
| Деталь: | MOUNT PRIMARY FEED R |
| Парткод: | 302K906270 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 302K906700 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | SHAFT ASSIST PULLEY |
| Парткод: | 302K906710 |
| Деталь: | HOLDER RETARD |
| Парткод: | 302K906151 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | LOWER BUSHING,PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | TORQUE-LIMITER 390 |
| Парткод: | 302K906750 |
| Деталь: | PLATE RETARD HOLDER |
| Парткод: | 302K906300 |
| Деталь: | FULCRUM-PIN RETARD |
| Парткод: | 302N406150 |
| Деталь: | LEVER RETARD RELEASE |
| Парткод: | 302N406130 |
| Деталь: | SPRING RETARD |
| Парткод: | 302N406200 |
| Деталь: | SHEET PRIMARY FEED HI |
| Парткод: | 302K906721 |
| Деталь: | GUIDE PRIM FEED WIRE |
| Парткод: | 302K906250 |
| Деталь: | WIRE PRIMARY FEED UNIT |
| Парткод: | 303NJ46160 |
| Деталь: | GUIDE FRONT LOWER |
| Парткод: | 302N406060 |
| Деталь: | SPRING RETARD LOCK |
| Парткод: | 302N406140 |
| Деталь: | HOLDER SENSOR FEED |
| Парткод: | 302K906290 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | HOLDER PICKUP |
| Парткод: | 302N406050 |
| Деталь: | PIN PICK UP IDLE |
| Парткод: | 302K906080 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | SHAFT PICKUP PRIMARY |
| Парткод: | 302N406070 |
| Деталь: | ONEWAY-CLUTCH 6 |
| Парткод: | 302N406120 |
| Деталь: | SPRING PICK UP |
| Парткод: | 302K906260 |
| Деталь: | PLATE PRIMARY FEED DRIVE |
| Парткод: | 302K906111 |
| Деталь: | HOLDER PRIM FEED PULLEY |
| Парткод: | 302K906280 |
| Деталь: | SHEET SOLENOID |
| Парткод: | 303NF06350 |
| Деталь: | GUIDE VF RIGHT |
| Парткод: | 303NF06131 |
| Деталь: | FRONT SPONGE CASE STAY |
| Парткод: | 302H715070 |
| Деталь: | SHAFT PULLEY PF |
| Парткод: | 303NJ06080 |
| Деталь: | PULLEY FEED PF |
| Парткод: | 303NJ06070 |
| Деталь: | HOLDER PULLEY PF |
| Парткод: | 303NJ06060 |
| Деталь: | MOUNT PRIMARY FEED |
| Парткод: | 302K906100 |
| Деталь: | WIRE VERTICAL 1 |
| Парткод: | 303NJ46080 |
| Деталь: | PLATE EARTH VF |
| Парткод: | 303NF06230 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GUIDE JUNCTION VF |
| Парткод: | 303NF06090 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | PARTS ROLLER CONVEYING VF SP |
| Парткод: | 303NF94070 |
| Деталь: | ACTUATOR VF SENSOR |
| Парткод: | 303NF06210 |
| Деталь: | COVER MIDDLE |
| Парткод: | 303NF06240 |
| Деталь: | SPRING ACT DU |
| Парткод: | 302H729120 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | MOUNT SENSOR VF |
| Парткод: | 303NF06220 |
| Деталь: | STOPPER PI |
| Парткод: | 302GR17970 |
| Деталь: | PARTS PRIMARY FEED UNIT DECK SP |
| Парткод: | 302N294030 |
| Деталь: | PARTS GUIDE VF RIGHT SET SP |
| Парткод: | 303NF94162 |
| Деталь: | PARTS MIDDLE ROLLER UNIT SP |
| Парткод: | 303NF94010 |
| Деталь: | PARTS SENSOR OPT. SET SP |
| Парткод: | 303NF94080 |
| Деталь: | GEAR Z160R |
| Парткод: | 302K931030 |
| Деталь: | BEARING 6800ZZ(7MM) |
| Парткод: | 7BE010197431H01 |
| Деталь: | STOPPER 8 |
| Парткод: | 302K921120 |
| Деталь: | CUT-WASHER 8X17 |
| Парткод: | 302K931840 |
| Деталь: | HOLDER DRUM DRIVE |
| Парткод: | 302K931013 |
| Деталь: | PLATE DRUM DRIVE |
| Парткод: | 302K931022 |
| Деталь: | PLATE EARTH DRUM |
| Парткод: | 302K931070 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | PLATE MOTOR DRUM |
| Парткод: | 302K931100 |
| Деталь: | PARTS MOTOR-BL W20 DRUM Z11 SP |
| Парткод: | 302LC94461 |
| Деталь: | HOLDER BEARING SUPPORT |
| Парткод: | 302K931060 |
| Деталь: | SPRING DRUM JOINT |
| Парткод: | 302LC31070 |
| Деталь: | COUPLING DRUM |
| Парткод: | 302K931130 |
| Деталь: | SHAFT DRUM DRIVE |
| Парткод: | 302LF31010 |
| Деталь: | WIRE DRUM MOT |
| Парткод: | 302LF46290 |
| Деталь: | PARTS MOTOR-BL W30 SP |
| Парткод: | 302K994331 |
| Деталь: | GEAR Z90R JOINT |
| Парткод: | 302K931620 |
| Деталь: | SPRING PADDLE CONT D |
| Парткод: | 302H731650 |
| Деталь: | JOINT FUSER DRIVE |
| Парткод: | 302K931640 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CUT WASHER 5X10 |
| Парткод: | 302LC31640 |
| Деталь: | GEAR Z67S-Z25S |
| Парткод: | 302K931670 |
| Деталь: | SPRING JOINT |
| Парткод: | 302K931660 |
| Деталь: | GEAR Z50S JOINT |
| Парткод: | 302K931630 |
| Деталь: | WIRE FUSER MOTOR H |
| Парткод: | 302K946100 |
| Деталь: | PLATE FUSER DRIVE |
| Парткод: | 302K931612 |
| Деталь: | MOUNT DRUM DRIVE |
| Парткод: | 302LF31630 |
| Деталь: | WIRE DLP MOT |
| Парткод: | 302N746130 |
| Деталь: | PARTS MOTOR-BL W30 DLP SP |
| Парткод: | 302K994891 |
| Деталь: | PARTS MOTOR PM FEED SP |
| Парткод: | 302K994300 |
| Деталь: | PLATE REGIST DRIVE |
| Парткод: | 302LF31610 |
| Деталь: | BUSHING,TRANSFER |
| Парткод: | 2A116180 |
| Деталь: | WIRE REGIST MOTOR |
| Парткод: | 302K946550 |
| Деталь: | PARTS DRUM DRIVE H SP |
| Парткод: | 302LF93071 |
| Деталь: | PARTS FUSER DRIVE UNIT SP |
| Парткод: | 302K994692 |
| Деталь: | PARTS DLP MOTOR ASSY(Z) SP |
| Парткод: | 302LF94120 |
| Деталь: | ACTUATOR RELAY |
| Парткод: | 302LF28060 |
| Деталь: | PARTS ROLLER RELAY MIDDLE B SP |
| Парткод: | 302LF94430 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | JOINT DRIVE |
| Парткод: | 302LF28121 |
| Деталь: | COVER RELAY |
| Парткод: | 302LF28521 |
| Деталь: | LABEL RELAY A4 |
| Парткод: | 302K934180 |
| Деталь: | GUIDE RELAY LOWER |
| Парткод: | 302LF28023 |
| Деталь: | SHEET RELAY LOWER |
| Парткод: | 302LF28820 |
| Деталь: | MAGNET UPPER REG GUIDE |
| Парткод: | 2FB17200 |
| Деталь: | SPRING-TORSION SWITCHBACK |
| Парткод: | 302K928190 |
| Деталь: | BUSH CONTACT MPT B |
| Парткод: | 302FZ07310 |
| Деталь: | PLATE EARTH ROLLER |
| Парткод: | 302LF28161 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | SPRING-COMPRESSION JOINT |
| Парткод: | 302LF28441 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | BELT S2M-Z133 |
| Парткод: | 302LF28130 |
| Деталь: | PULLEY P18-S2M |
| Парткод: | 302LF28342 |
| Деталь: | HOLDER SHAFT OUT |
| Парткод: | 302FZ07540 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | SPRING-EXTENSION EARTH |
| Парткод: | 302LF28500 |
| Деталь: | HANDLE FRONT |
| Парткод: | 302LF28510 |
| Деталь: | SHAFT HANDLE |
| Парткод: | 302LF28181 |
| Деталь: | JOINT RELAY |
| Парткод: | 302LF28201 |
| Деталь: | ARM LEVER RELAY |
| Парткод: | 302LF28190 |
| Деталь: | PLATE HINGE STOPPER |
| Парткод: | 302LF28780 |
| Деталь: | GUIDE RELAY UPPER |
| Парткод: | 302LF28011 |
| Деталь: | PLATE REINFORCEMENT |
| Парткод: | 302LF28050 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | 302K934150 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | SPRING PULLEY |
| Парткод: | 302F928170 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING-TORSION HOOK |
| Парткод: | 302LF28580 |
| Деталь: | HOOK LEVER JAM JS R |
| Парткод: | 303MA16580 |
| Деталь: | GUIDE PRESS ROTARY |
| Парткод: | 302LF28380 |
| Деталь: | PARTS ROLLER PRESS SP |
| Парткод: | 302LF94280 |
| Деталь: | BEARING MR126ZZ |
| Парткод: | 7BE006124431H01 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | PARTS ROLLER PRESS DRIVE SP |
| Парткод: | 302LF94270 |
| Деталь: | GEAR Z30L DECURLER |
| Парткод: | 302LF28650 |
| Деталь: | CAP PRESS UNIT |
| Парткод: | 302LF28370 |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 303NJ31120 |
| Деталь: | GEAR Z14S-Z35R |
| Парткод: | 302LF28330 |
| Деталь: | GEAR PRESS DRIVE |
| Парткод: | 302LF28360 |
| Деталь: | GUIDE RIGHT UPPER |
| Парткод: | 302LF28071 |
| Деталь: | GUIDE RIGHT LOWER |
| Парткод: | 302LF28082 |
| Деталь: | GEAR Z21S |
| Парткод: | 302LF28280 |
| Деталь: | PLATE SUPPORT SLIDER |
| Парткод: | 302LF28170 |
| Деталь: | JOINT HANDLE |
| Парткод: | 302LF28210 |
| Деталь: | LABEL RELAY A3 |
| Парткод: | 302K934170 |
| Деталь: | PARTS GUIDE RELAY UPPER UNIT SP |
| Парткод: | 302K994C33 |
| Деталь: | PARTS PWB BRIDGE ASSY SP |
| Парткод: | 302K994830 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | GEAR Z31R-Z20R |
| Парткод: | 302LF28140 |
| Деталь: | GEAR Z42L |
| Парткод: | 302LF28150 |
| Деталь: | GEAR Z14S-Z30R |
| Парткод: | 302LF28300 |
| Деталь: | ACTUATOR PRESS |
| Парткод: | 302LF28470 |
| Деталь: | GEAR Z21S |
| Парткод: | 302LF28280 |
| Деталь: | GEAR Z21S-Z40R |
| Парткод: | 302LF28290 |
| Деталь: | PARTS MOTOR PM FEED SP |
| Парткод: | 302K994300 |
| Деталь: | FRAME DRIVE |
| Парткод: | 302LF28093 |
| Деталь: | PLATE DRIVE A |
| Парткод: | 302LF28101 |
| Деталь: | WIRE OPEN SWITCH |
| Парткод: | 302LF46B40 |
| Деталь: | WIRE FEED SENSOR |
| Парткод: | 302LF46B50 |
| Деталь: | WIRE INTERFACE |
| Парткод: | 302LF46B10 |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 303NJ31120 |
| Деталь: | PLATE MOTOR DRIVE |
| Парткод: | 302LF28113 |
| Деталь: | GUIDE HARNESS |
| Парткод: | 302LF28560 |
| Деталь: | GROUND PLATE DECK UNIT |
| Парткод: | 302FB09320 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | PLATE MOTOR PRESS DRIVE |
| Парткод: | 302LF28461 |
| Деталь: | GUIDE DECURLER PIN |
| Парткод: | 302LF28600 |
| Деталь: | WIRE GUIDE MOTOR |
| Парткод: | 302LF46B30 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | STOPPER RELAY |
| Парткод: | 302LF28590 |
| Деталь: | SPRING COMPRESSION RELAY |
| Парткод: | 302LF28610 |
| Деталь: | PARTS RELAY DRIVE UNIT SP |
| Парткод: | 302K994C00 |
| Деталь: | SCREW WASTE |
| Парткод: | 302LF03110 |
| Деталь: | SEAL SCREW |
| Парткод: | 302H703430 |
| Деталь: | BUSHING,TRANSFER |
| Парткод: | 2A116180 |
| Деталь: | PIPE WASTE LOWER |
| Парткод: | 302LF03061 |
| Деталь: | SEAL PIPE WASTE A |
| Парткод: | 302LF03090 |
| Деталь: | SEAL PIPE WASTE B |
| Парткод: | 302H703740 |
| Деталь: | PIPE WASTE UPPER |
| Парткод: | 302LF03051 |
| Деталь: | GEAR Z18S |
| Парткод: | 302K903140 |
| Деталь: | GEAR IDLE Z20S-Z15R |
| Парткод: | 302K903180 |
| Деталь: | GEAR Z36S-Z15R |
| Парткод: | 302K903240 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR Z35S |
| Парткод: | 302K903130 |
| Деталь: | SEAL PIPE UPPER |
| Парткод: | 302LF03120 |
| Деталь: | HOLDER DRIVE |
| Парткод: | 302LF03220 |
| Деталь: | SEAL PIPE BOTTLE |
| Парткод: | 302LF03100 |
| Деталь: | SHUTTER PIPE LOWER |
| Парткод: | 302LC03451 |
| Деталь: | SPRING PIPE LOW |
| Парткод: | 302LK03A50 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | SHAFT DRIVE A |
| Парткод: | 302LF03150 |
| Деталь: | SHAFT DRIVE B |
| Парткод: | 302K903200 |
| Деталь: | MOUNT PIPE |
| Парткод: | 302LF03360 |
| Деталь: | WT-861/WASTE TONER BOTTLE |
| Парткод: | 1902K90UN0 |
| Деталь: | PARTS PIPE WASTE ASSY SP |
| Парткод: | 302LF94130 |
| Деталь: | RUBBER BOLT |
| Парткод: | 303LM02170 |
| Деталь: | SHEET BOLT RUBBER |
| Парткод: | 303LM02230 |
| Деталь: | BOLT DECK STOPPER |
| Парткод: | 303NF02210 |
| Деталь: | CASTER UA |
| Парткод: | 302A002171 |
| Деталь: | SHAFT HOOK PULLEY |
| Парткод: | 303NF02290 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | LEVER DECK HOOK |
| Парткод: | 303NF02270 |
| Деталь: | PULLEY,CASSETTE RAIL |
| Парткод: | 302FG07020 |
| Деталь: | SPRING DECK HOOK |
| Парткод: | 303NF02310 |
| Деталь: | SHAFT HOOK FULCRUM |
| Парткод: | 303NF02280 |
| Деталь: | SPRING CASSETTE HOOK |
| Парткод: | 302LH02050 |
| Деталь: | SLIDER DECK |
| Парткод: | 303NF10030 |
| Деталь: | RAIL DECK FEED |
| Парткод: | 303NF02150 |
| Деталь: | RAIL CONVEYING |
| Парткод: | 303NF02260 |
| Деталь: | SLIDER CASSETTE |
| Парткод: | 302FZ09050 |
| Деталь: | PIN STAY |
| Парткод: | 303LM02181 |
| Деталь: | BOLT STOPPER |
| Парткод: | 303LM02132 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | HOLDER DECK HOOK |
| Парткод: | 303NF02301 |
| Деталь: | MOUNT BRACKET DESK |
| Парткод: | 303NF39010 |
| Деталь: | MOUNT FOOT REAR |
| Парткод: | 303NF02190 |
| Деталь: | MOUNT SLIDER DECK |
| Парткод: | 303NF02171 |
| Деталь: | PLATE BOLT FRONT |
| Парткод: | 303NF02130 |
| Деталь: | STAY UPPER RIGHT |
| Парткод: | 303NF02060 |
| Деталь: | PLATE LOW |
| Парткод: | 303NF02121 |
| Деталь: | MOUNT EARTH REAR |
| Парткод: | 303NF02340 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | PLATE JOINT RIGHT |
| Парткод: | 302K902290 |
| Деталь: | LID KMAS |
| Парткод: | 2C912430 |
| Деталь: | COVER RIGHT |
| Парткод: | 302K929201 |
| Деталь: | SEAL INNER COVER LOW A |
| Парткод: | 302LF03310 |
| Деталь: | SEAL INNER COVER LOW B |
| Парткод: | 302LF03320 |
| Деталь: | COVER INNER UPPER |
| Парткод: | 302LF04011 |
| Деталь: | COVER REAR UPPER |
| Парткод: | 302N404391 |
| Деталь: | COVER REAR LOWER Z |
| Парткод: | 302N704090 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302LF04130 |
| Деталь: | LID FAX BOARD |
| Парткод: | 302LC04471 |
| Деталь: | LABEL MPF PUSH |
| Парткод: | 302LC34110 |
| Деталь: | COVER RIGHT UPPER |
| Парткод: | 302N204140 |
| Деталь: | LABEL MPF CAUTION B |
| Парткод: | 302LC34070 |
| Деталь: | COVER INNER LOWER |
| Парткод: | 302LF04020 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302K904620 |
| Деталь: | HOLDER CLIP A |
| Парткод: | 302K904210 |
| Деталь: | HOLDER CLIP B |
| Парткод: | 302K904220 |
| Деталь: | COVER INNER CONVEYING B |
| Парткод: | 302K929590 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 302LC03500 |
| Деталь: | LEVER WASTE BOTTLE |
| Парткод: | 302K903081 |
| Деталь: | SPRING CHANGE PULLEY |
| Парткод: | 2BL21340 |
| Деталь: | WIRE RETAINER JOINT |
| Парткод: | 302LF46200 |
| Деталь: | SEAL FRONT COVER R B |
| Парткод: | 302K933F80 |
| Деталь: | BRUSH CLEANER |
| Парткод: | 2BL16220 |
| Деталь: | FILTER LEFT SIDE |
| Парткод: | 302K933A80 |
| Деталь: | LID DISPOSAL |
| Парткод: | 302N233110 |
| Деталь: | COVER FILTER LEFT SIDE |
| Парткод: | 302N233020 |
| Деталь: | LABEL MPF SET A |
| Парткод: | 302LC34180 |
| Деталь: | PARTS DISPOSAL UNIT(M2) SP |
| Парткод: | 302N294120 |
| Деталь: | Ролик отделения бумаги в автоподатчике документов |
| Парткод: | 303LL07191 |
| Цена: | 5 500 ₽ |
| Деталь: | CASE TONER HOPPER |
| Парткод: | 302LF15012 |
| Деталь: | SPONGE HOPPER A |
| Парткод: | 302LF15170 |
| Деталь: | SPONGE HOPPER B |
| Парткод: | 302K915360 |
| Деталь: | CAP TONER |
| Парткод: | 302K915470 |
| Деталь: | OIL SEAL |
| Парткод: | 302KY12020 |
| Деталь: | SCREW TONER SUPPLY |
| Парткод: | 302K915070 |
| Деталь: | CAP SCREW |
| Парткод: | 302FZ23260 |
| Деталь: | SEAL HOPPER LOW |
| Парткод: | 302K915381 |
| Деталь: | SHUTTER HOPPER LOW |
| Парткод: | 302K915230 |
| Деталь: | SPRING PIPE LOW |
| Парткод: | 302H703140 |
| Деталь: | TONER EMPTY DETECTION SENSOR |
| Парткод: | 3033915181 |
| Деталь: | PADDLE TONER SUPPLY A |
| Парткод: | 302K915110 |
| Деталь: | PADDLE TONER SUPPLY B |
| Парткод: | 302K915120 |
| Деталь: | SPRING TONER SENSOR A |
| Парткод: | 302K915390 |
| Деталь: | GEAR Z15S IDLE |
| Парткод: | 302LF15030 |
| Деталь: | GEAR Z60S |
| Парткод: | 302LF15070 |
| Деталь: | GEAR Z30S |
| Парткод: | 302K915180 |
| Деталь: | LID TONER HOPPER |
| Парткод: | 302LF15020 |
| Деталь: | SEAL HOPPER UP |
| Парткод: | 302K915370 |
| Деталь: | SHUTTER HOPPER UP |
| Парткод: | 302K915460 |
| Деталь: | BUSHING,TRANSFER |
| Парткод: | 2A116180 |
| Деталь: | SHAFT DRIVE |
| Парткод: | 302K915330 |
| Деталь: | GEAR Z14S |
| Парткод: | 302K915400 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SHAFT TONER SUPPLY |
| Парткод: | 302LF15050 |
| Деталь: | BUSH SCREW |
| Парткод: | 302K915450 |
| Деталь: | GEAR Z21S-Z15S |
| Парткод: | 302K915160 |
| Деталь: | GEAR Z32R-Z14S |
| Парткод: | 302K915210 |
| Деталь: | GEAR Z21S |
| Парткод: | 302K915200 |
| Деталь: | GEAR Z48L |
| Парткод: | 302K915190 |
| Деталь: | GEAR Z32L |
| Парткод: | 302K915080 |
| Деталь: | MOUNT PI |
| Парткод: | 302K921410 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | PARTS CONV RELEASE MOTOR ASSY SP |
| Парткод: | 302LC94190 |
| Деталь: | HOLDER TONER MOTOR |
| Парткод: | 302LF15080 |
| Деталь: | SEAL MOTOR DC |
| Парткод: | 302LC31511 |
| Деталь: | PLATE DC MOTOR 6 |
| Парткод: | 302K908660 |
| Деталь: | WIRE TONER LEVEL SENSOR |
| Парткод: | 302K946A80 |
| Деталь: | PLATE INNER FRAME |
| Парткод: | 302LF03021 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | LEVER HOOK |
| Парткод: | 302LF03080 |
| Деталь: | SPRING LEVER L |
| Парткод: | 302LF03410 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | SEAL SHUTTER DUCT |
| Парткод: | 302LF03540 |
| Деталь: | SPRING LEVER R |
| Парткод: | 302LF03400 |
| Деталь: | DUCT DLP |
| Парткод: | 302LF03250 |
| Деталь: | SEAL DUCT DLP A |
| Парткод: | 302LF03900 |
| Деталь: | WIRE RETAINER |
| Парткод: | 302LF46190 |
| Деталь: | SHUTTER DUCT WASTE |
| Парткод: | 302LF03530 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302LC94380 |
| Деталь: | SPONGE FAN |
| Парткод: | 302K903250 |
| Деталь: | SHEET DUCT DLP |
| Парткод: | 302LF03070 |
| Деталь: | SCREW FAN |
| Парткод: | 302H733430 |
| Деталь: | DUCT WASTE B |
| Парткод: | 302LF03520 |
| Деталь: | DUCT WASTE A |
| Парткод: | 302LF03511 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | SEAL INNER COOLING C |
| Парткод: | 302LC33540 |
| Деталь: | SEAL DUCT DLP B |
| Парткод: | 302LF03910 |
| Деталь: | DUCT DRUM |
| Парткод: | 302LF03371 |
| Деталь: | LEVER CASS SHUTTER |
| Парткод: | 302LF03011 |
| Деталь: | LID DRUM DUCT |
| Парткод: | 302LF03380 |
| Деталь: | WORK PLATE CASS |
| Парткод: | 302LF03460 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | COVER INNER |
| Парткод: | 302LF03041 |
| Деталь: | SEAL DUCT DLP C |
| Парткод: | 302LF03920 |
| Деталь: | PARTS FILTER DRUM SP |
| Парткод: | 302LF94310 |
| Деталь: | PARTS FILTER DLP SP |
| Парткод: | 302LF94320 |
| Деталь: | SEAL DUCT DRUM A |
| Парткод: | 302LF03930 |
| Деталь: | SEAL DUCT DRUM B |
| Парткод: | 302LF03940 |
| Деталь: | SEAL DUCT CASS A |
| Парткод: | 302LF03960 |
| Деталь: | SEAL DUCT CASS B |
| Парткод: | 302LF03970 |
| Деталь: | SEAL DUCT DRUM C |
| Парткод: | 302LF03980 |
| Деталь: | SEAL INNER |
| Парткод: | 302LF03991 |
| Деталь: | FILM INNER FRAME |
| Парткод: | 302LF03281 |
| Деталь: | SEAL COOLING FAN A |
| Парткод: | 302K903860 |
| Деталь: | SEAL COOLING FAN B |
| Парткод: | 302K903870 |
| Деталь: | PARTS INNER UNIT SP |
| Парткод: | 302LF94043 |
| Деталь: | GEAR Z28 FEED |
| Парткод: | 302N406170 |
| Деталь: | PULLEY FEED |
| Парткод: | 302N406030 |
| Цена: | 440 ₽ |
| Деталь: | GEAR Z32 FEED OW |
| Парткод: | 302N406100 |
| Деталь: | GEAR Z32 PICKUP |
| Парткод: | 302N406110 |
| Деталь: | SPRING DU |
| Парткод: | 302F925780 |
| Деталь: | PLATE FRAME UPPER |
| Парткод: | 302N406010 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 302K906510 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302K906321 |
| Деталь: | GEAR PRIMARY FEED IDLE Z20R Z16L |
| Парткод: | 302K906230 |
| Деталь: | PARTS ROLLER ASSIST SP |
| Парткод: | 303NJ94050 |
| Деталь: | GEAR FEED DRIVE Z20L |
| Парткод: | 302K906240 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR PRIMARY FEED Z17L OW |
| Парткод: | 303NJ06040 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 302K994580 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | PULLEY RETARD |
| Парткод: | 302N406040 |
| Цена: | 450 ₽ |
| Деталь: | LEVER RETARD LOCK |
| Парткод: | 302N406160 |
| Деталь: | PLATE RETARD ADJUST |
| Парткод: | 302K906420 |
| Деталь: | MOUNT PRIMARY FEED R |
| Парткод: | 302K906270 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 302K906700 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | SHAFT ASSIST PULLEY |
| Парткод: | 302K906710 |
| Деталь: | HOLDER RETARD |
| Парткод: | 302K906151 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | LOWER BUSHING,PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | TORQUE-LIMITER 390 |
| Парткод: | 302K906750 |
| Деталь: | PLATE RETARD HOLDER |
| Парткод: | 302K906300 |
| Деталь: | FULCRUM-PIN RETARD |
| Парткод: | 302N406150 |
| Деталь: | LEVER RETARD RELEASE |
| Парткод: | 302N406130 |
| Деталь: | SPRING RETARD |
| Парткод: | 302N406200 |
| Деталь: | SHEET PRIMARY FEED HI |
| Парткод: | 302K906721 |
| Деталь: | GUIDE PRIM FEED WIRE |
| Парткод: | 302K906250 |
| Деталь: | WIRE PRIMARY FEED UNIT |
| Парткод: | 303NJ46160 |
| Деталь: | GUIDE FRONT LOWER |
| Парткод: | 302N406060 |
| Деталь: | SPRING RETARD LOCK |
| Парткод: | 302N406140 |
| Деталь: | HOLDER SENSOR FEED |
| Парткод: | 302K906290 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | HOLDER PICKUP |
| Парткод: | 302N406050 |
| Деталь: | PIN PICK UP IDLE |
| Парткод: | 302K906080 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | SHAFT PICKUP PRIMARY |
| Парткод: | 302N406070 |
| Деталь: | ONEWAY-CLUTCH 6 |
| Парткод: | 302N406120 |
| Деталь: | SPRING PICK UP |
| Парткод: | 302K906260 |
| Деталь: | PLATE PRIMARY FEED DRIVE |
| Парткод: | 302K906111 |
| Деталь: | HOLDER PRIM FEED PULLEY |
| Парткод: | 302K906280 |
| Деталь: | SHEET SOLENOID |
| Парткод: | 303NF06350 |
| Деталь: | MOUNT PRIMARY FEED |
| Парткод: | 302K906100 |
| Деталь: | PARTS PRIMARY FEED UNIT DECK SP |
| Парткод: | 302N294030 |
| Деталь: | GUIDE FEED LOW |
| Парткод: | 302K906610 |
| Деталь: | SPRING TENSION |
| Парткод: | 2DC12170 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | HOLDER FEED LOW PULLEY |
| Парткод: | 302K906640 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 302K906510 |
| Деталь: | PULLEY MIDDLE A |
| Парткод: | 302H722760 |
| Деталь: | COVER FEED LOW |
| Парткод: | 302K906600 |
| Деталь: | LID SIDE FEED |
| Парткод: | 302K906691 |
| Деталь: | SHAFT FEED LOW HOOK |
| Парткод: | 302K906681 |
| Деталь: | HANDLE FEED LOW |
| Парткод: | 302K906660 |
| Деталь: | HOOK FEED LOW |
| Парткод: | 302K906670 |
| Деталь: | SPRING LID |
| Парткод: | 302FZ20021 |
| Деталь: | BAND B |
| Парткод: | 2BG06480 |
| Деталь: | PLATE FEED LOW |
| Парткод: | 302K906500 |
| Деталь: | PARTS ROLLER FEED LOW SP |
| Парткод: | 302K994430 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | WIRE GUIDE FEED LOW |
| Парткод: | 302K946430 |
| Деталь: | ACTUATOR FEED LOW |
| Парткод: | 302N706500 |
| Деталь: | SPRING FEED ACT |
| Парткод: | 302K906520 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | GUIDE WIRE FEED LOW |
| Парткод: | 302LC06210 |
| Деталь: | PARTS PAD ROLLER SET SP |
| Парткод: | 302K994D70 |
| Деталь: | SPRING HV |
| Парткод: | 302K939360 |
| Деталь: | PLATE HV |
| Парткод: | 302K924620 |
| Деталь: | SHAFT DRIVE MIDDLE |
| Парткод: | 302N224010 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | BRACKET KEY MIDDLE A |
| Парткод: | 302K924660 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | GEAR Z27L Z24L |
| Парткод: | 302K924690 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS ROLLER MIDDLE L SP |
| Парткод: | 302LC94550 |
| Деталь: | PARTS MOTOR HB MID SP |
| Парткод: | 302K994A80 |
| Деталь: | PLATE MIDDLE MOUNT A |
| Парткод: | 302K924650 |
| Деталь: | PLATE EARTH MIDDLE |
| Парткод: | 302K924570 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | GEAR Z20S |
| Парткод: | 302K924600 |
| Деталь: | GEAR Z19S IDLE |
| Парткод: | 302K924640 |
| Деталь: | GEAR Z42R Z23S |
| Парткод: | 302K924630 |
| Деталь: | SEAL MIDDLE FEED |
| Парткод: | 302LF33910 |
| Деталь: | COVER MOTOR MIDDLE |
| Парткод: | 302N724020 |
| Деталь: | MOUNT CLEANER REGIST |
| Парткод: | 302LF24140 |
| Деталь: | WIRE GUIDE FEED MIDDLE |
| Парткод: | 302K946451 |
| Деталь: | SWITCH REGISTRATION |
| Парткод: | 2FG27110 |
| Деталь: | HOLDER SENSOR MIDDLE |
| Парткод: | 302K924870 |
| Деталь: | SENSOR,CONVEYING |
| Парткод: | 3H327410 |
| Деталь: | HOLDER SENSOR REGIST |
| Парткод: | 302K924861 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | FILM FEED UPPER |
| Парткод: | 302LF33580 |
| Деталь: | SHEET COVER SENSOR |
| Парткод: | 302K924890 |
| Деталь: | SHEET REGIST L C |
| Парткод: | 302K924881 |
| Деталь: | SHEET REGIST L A |
| Парткод: | 302K924560 |
| Деталь: | FRAME MIDDLE FEED |
| Парткод: | 302K924530 |
| Деталь: | SPACER FRAME REAR |
| Парткод: | 302LF22590 |
| Деталь: | SHEET PROTECTOR TONER F |
| Парткод: | 302LF22650 |
| Деталь: | SHEET PROTECTOR TONER R |
| Парткод: | 302LF22660 |
| Деталь: | PARTS ROLLER REGIST H SP |
| Парткод: | 302K994A00 |
| Деталь: | STOPPER 8 |
| Парткод: | 302K921120 |
| Деталь: | GEAR Z24L |
| Парткод: | 302K924510 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | BEARING 696ZZNR |
| Парткод: | 7BE006155J31H01 |
| Деталь: | PARTS GEAR Z48R SP |
| Парткод: | 302K994560 |
| Деталь: | PARTS CLEANER REGIST ASSY SP |
| Парткод: | 302LF94160 |
| Цена: | 3 500 ₽ |
| Деталь: | PLATE MIDDLE FEED |
| Парткод: | 302K924542 |
| Деталь: | PARTS REGIST GUIDE ASSY SP |
| Парткод: | 302LC94680 |
| Деталь: | GUIDE TRANSFER FRONT A |
| Парткод: | 302LF22070 |
| Деталь: | SPACER FRAME FRONT |
| Парткод: | 302LF22580 |
| Деталь: | PARTS GUIDE FEED MIDDLE ASSY SP |
| Парткод: | 302K994132 |
| Цена: | 4 900 ₽ |
| Деталь: | PARTS GUIDE FEED REGIST ASSY SP |
| Парткод: | 302LF94113 |
| Деталь: | PARTS REGIST GUIDE SET SP |
| Парткод: | 302LC94691 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | PARTS ROLLER RELAY EXIT MIDDLE SP |
| Парткод: | 302LF94030 |
| Деталь: | PARTS ROLLER RELAY EXIT LOWER B SP |
| Парткод: | 302LF94440 |
| Деталь: | ACTUATOR RELAY EXIT SW |
| Парткод: | 302LF28350 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | 63212210 |
| Деталь: | PARTS SOLENOID FEED SHIFT SP |
| Парткод: | 302K994370 |
| Деталь: | GEAR Z20R-P18 |
| Парткод: | 302LF28420 |
| Деталь: | LABEL EXIT A2 |
| Парткод: | 302K934160 |
| Деталь: | STATIC-ELIMINATOR EJECT |
| Парткод: | 302LF28640 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | PLATE EARTH EXIT |
| Парткод: | 302LF28630 |
| Деталь: | SPRING-COMPRESSION RELAY EXIT |
| Парткод: | 302LF28840 |
| Деталь: | HOUSING RELAY EXIT |
| Парткод: | 302LF28222 |
| Деталь: | PLATE EARTH ROLLER A |
| Парткод: | 302LF28541 |
| Деталь: | BEARING MF106ZZ |
| Парткод: | 7BE006103R31H01 |
| Деталь: | PULLEY P18-S2M |
| Парткод: | 302LF28342 |
| Деталь: | BELT 150S2M,PAPER FEED |
| Парткод: | 3HL07190 |
| Деталь: | SPRING-TORSION SWITCHBACK |
| Парткод: | 302K928190 |
| Деталь: | PARTS GUIDE RELAY EXIT SHEFT SP |
| Парткод: | 303NB94190 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 302JF22010 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | PLATE EARTH EXIT |
| Парткод: | 302LF28531 |
| Деталь: | GROUND PLATE SCANNER B |
| Парткод: | 2C912690 |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 303NJ31120 |
| Деталь: | BELT S2M-Z112 |
| Парткод: | 302LF28450 |
| Деталь: | PULLEY TENSION BELT |
| Парткод: | 302FZ07150 |
| Деталь: | MOUNT RELAY EXIT |
| Парткод: | 302LF28250 |
| Деталь: | PLATE REINFOCEMENT |
| Парткод: | 302LF28800 |
| Деталь: | GUIDE RELAY EXIT RIGHT |
| Парткод: | 302LF28241 |
| Деталь: | WIRE EXIT SENSOR |
| Парткод: | 302LF46B60 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SPRING-TORSION RELAY EXIT |
| Парткод: | 302LF28810 |
| Деталь: | PLATE RELAY SOLENOID |
| Парткод: | 302LF28401 |
| Деталь: | LEVER RELAY SOLENOID |
| Парткод: | 302LF28410 |
| Деталь: | SPRING,LF SHIFT GUIDE |
| Парткод: | 3HL10090 |
| Деталь: | GUIDE RELAY EXIT UPPER |
| Парткод: | 302LF28230 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING PULLEY |
| Парткод: | 302F928170 |
| Деталь: | EXIT PUSH |
| Парткод: | 302FZ28260 |
| Деталь: | SPRING EXIT PUSH |
| Парткод: | 302FZ28270 |
| Деталь: | PLATE EARTH RELAY B |
| Парткод: | 302LF28661 |
| Деталь: | COVER RELAY EXIT |
| Парткод: | 302LF28272 |
| Деталь: | PLATE REINFORCEMENT EXIT |
| Парткод: | 302LF28621 |
| Деталь: | SLIDER RELEASE |
| Парткод: | 302LF28720 |
| Деталь: | PARTS RELAY EXIT UNIT SP |
| Парткод: | 302LF94385 |
| Деталь: | Правая часть узла термозакрепления, в сборе |
| Парткод: | FK-6702 |
| Деталь: | PARTS ROLLER CONVEYING LEFT SP |
| Парткод: | 303M494090 |
| Деталь: | PARTS ROLLER CONVEYING RIGHT SP |
| Парткод: | 303M494100 |
| Деталь: | PARTS FAN COOLING CONV |
| Парткод: | 302H794490 |
| Деталь: | GUIDE READING |
| Парткод: | 303M424251 |
| Деталь: | PULLEY GUIDE READING |
| Парткод: | 303LL24190 |
| Деталь: | SHEET LEFT READING |
| Парткод: | 303M424200 |
| Деталь: | GUIDE LEFT READING |
| Парткод: | 303M424210 |
| Деталь: | SPRING BYPASSFFED |
| Парткод: | 302H008140 |
| Деталь: | SPRING PICK UP |
| Парткод: | 303NA06110 |
| Деталь: | SPONGE ORIGINAL MAT A |
| Парткод: | 303M802320 |
| Деталь: | GUIDE RIGHT READING |
| Парткод: | 303M824160 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303NW94040 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PARTS ROLLER REGISTRATION SP |
| Парткод: | 303M494070 |
| Деталь: | GEAR Z26 |
| Парткод: | 303M431110 |
| Деталь: | PARTS ROLLER CONVEYING UPPER SP |
| Парткод: | 303M494080 |
| Деталь: | GEAR 22 CIS IDLE |
| Парткод: | 303M431340 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | RING STOPPER/A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PULLEY,TIMING BELT |
| Парткод: | 28801190 |
| Деталь: | CUSHION ORIGINAL MAT |
| Парткод: | 303J902370 |
| Деталь: | PULLEY 38 CONVEYING |
| Парткод: | 303LL31330 |
| Деталь: | PULLEY CONVEYING BK |
| Парткод: | 303M824210 |
| Деталь: | PULLEY 48 CONV HIGH |
| Парткод: | 303M431320 |
| Деталь: | BEARING 688ZZ |
| Парткод: | 7BE008165431H01 |
| Деталь: | FAN COOLING 40-15 |
| Парткод: | 302H044120 |
| Деталь: | ACCESS.BUSHING |
| Парткод: | 7YZM110001++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | SPRING SIDE COVER |
| Парткод: | 302HN04250 |
| Деталь: | SPRING CURSOR SET |
| Парткод: | 302K309370 |
| Деталь: | HOLDER BEARING 688ZZ |
| Парткод: | 302K931960 |
| Деталь: | SPRING PUSH MAT |
| Парткод: | 303LL02430 |
| Деталь: | SPRING TENSION CONV |
| Парткод: | 303LL31390 |
| Деталь: | PLATE TENSION EJECT |
| Парткод: | 303LL31520 |
| Деталь: | MOUNT TIMING SW |
| Парткод: | 303M402100 |
| Деталь: | GUIDE CONV RIGHT |
| Парткод: | 303M424170 |
| Деталь: | STAY CONV RIGHT |
| Парткод: | 303M424180 |
| Деталь: | HOLDER LEFT PULLEY |
| Парткод: | 303M424190 |
| Деталь: | GUIDE CONV LEFT |
| Парткод: | 303M424221 |
| Деталь: | HOLDER READ PULLEY |
| Парткод: | 303M424261 |
| Деталь: | GUIDE CONVEYING LOW |
| Парткод: | 303M424270 |
| Деталь: | PLATE EARTH CONV LOWER |
| Парткод: | 303M424280 |
| Деталь: | BELT 60S1.5M326 |
| Парткод: | 303M431270 |
| Деталь: | KNOB JAM REMOVEMENT |
| Парткод: | 303M431280 |
| Деталь: | HOLDER RIGHT PULLEY |
| Парткод: | 303M824121 |
| Деталь: | SHAFT GUIDE READING |
| Парткод: | 303M824130 |
| Деталь: | SPRING GUIDE READING |
| Парткод: | 303M824140 |
| Деталь: | SHAFT PULLEY |
| Парткод: | 303M824200 |
| Деталь: | MOUNT CUSHION |
| Парткод: | 303LL02410 |
| Деталь: | CUSHION ORIGINAL MAT |
| Парткод: | 303LL02530 |
| Деталь: | HOLDER FAN |
| Парткод: | 303M402111 |
| Деталь: | GUIDE REGIST LOWER |
| Парткод: | 303M424060 |
| Деталь: | WIRE CIS FAN |
| Парткод: | 303M446100 |
| Деталь: | SHEET GUIDE CONV LEFT |
| Парткод: | 303M424440 |
| Деталь: | WIRE FAN |
| Парткод: | 303M446150 |
| Деталь: | PIN,HOOK FULCRUM |
| Парткод: | 3CZ02230 |
| Деталь: | STAY CONVEYING |
| Парткод: | 303M402060 |
| Деталь: | Узел переноса заряда в драм-картридже, в сборе |
| Парткод: | MC-6720 |
| Деталь: | SPRING DEV PUSH |
| Парткод: | 2C902080 |
| Деталь: | ACTUATOR CASSETTE |
| Парткод: | 303NF10230 |
| Деталь: | PARTS MOTOR LIFT DECK SP |
| Парткод: | 303NF94090 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | WIRE ENGINE I/F |
| Парткод: | 303NF46010 |
| Деталь: | WIRE MAIN MOTOR |
| Парткод: | 303NF46170 |
| Деталь: | PARTS PWB FRONT DECK ASSY SP |
| Парткод: | 303NF94060 |
| Деталь: | MOUNT ACTUATOR CASSETTE |
| Парткод: | 303NF10240 |
| Деталь: | SPRING ACT DU |
| Парткод: | 302H729120 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | GUIDE WIRE FRONT PWB |
| Парткод: | 302LF39050 |
| Деталь: | HOLDER PWB |
| Парткод: | 302K939230 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | WIRE LEFT DECK 1 |
| Парткод: | 303NF46230 |
| Деталь: | PIN,DRAWER SIDE CONVEYING |
| Парткод: | 3CZ02240 |
| Деталь: | WIRE LEFT |
| Парткод: | 303NF46090 |
| Деталь: | WIRE RIGHT |
| Парткод: | 303NF46110 |
| Деталь: | WIRE LIFTMOTOR |
| Парткод: | 303NF46080 |
| Деталь: | WIRE RIGHT DECK |
| Парткод: | 303NF46210 |
| Деталь: | HOLDER DECK SENSOR |
| Парткод: | 303NF10330 |
| Деталь: | GUIDE LOWER MID |
| Парткод: | 303NF06120 |
| Деталь: | WIRE VERTICAL 1 |
| Парткод: | 303NF46130 |
| Деталь: | GUIDE UPPER MID |
| Парткод: | 303NF06110 |
| Деталь: | WIRE SMT POWER |
| Парткод: | 303NF46060 |
| Деталь: | WIRE HEATER |
| Парткод: | 303NF46030 |
| Деталь: | WIRE PAPER SENSOR |
| Парткод: | 303NF46100 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | MOUNT PWB MAIN |
| Парткод: | 303NF39050 |
| Деталь: | SHIELD BOX |
| Парткод: | 302N439011 |
| Деталь: | RAIL PWB |
| Парткод: | 302K939030 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | BRACKET MAIN |
| Парткод: | 302N439030 |
| Деталь: | PARTS PWB KUIO ASSY SP |
| Парткод: | 302K994270 |
| Деталь: | WIRE FFC KUIO |
| Парткод: | 302N446090 |
| Деталь: | WIRE KUIO POWER |
| Парткод: | 302K946910 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390011++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302N794110 |
| Деталь: | PARTS PWB MAIN ASSY SP EU |
| Парткод: | 302N794120 |
| Деталь: | PARTS STORAGE DEVICE SP |
| Парткод: | 302N793090 |
| Деталь: | WIRE HDD POWER |
| Парткод: | 302K946A10 |
| Деталь: | WIRE HDD DATA 1 |
| Парткод: | 302N446130 |
| Деталь: | WIRE HDD DATA 2 |
| Парткод: | 302N446140 |
| Деталь: | HOLDER FAN MAIN |
| Парткод: | 302K939043 |
| Деталь: | FAN BOX COOLING |
| Парткод: | 302FZ44040 |
| Деталь: | WIRE PANEL-LVU |
| Парткод: | 302K946770 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | MOUNT CONNECTOR |
| Парткод: | 302N733220 |
| Деталь: | FILM SHIELD BOX |
| Парткод: | 302N439060 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | WIRE TONER DUCT FAN |
| Парткод: | 302N746140 |
| Деталь: | PARTS MEMORY MODULE SP |
| Парткод: | 302LH94230 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610016++H01 |
| Деталь: | PLATE OPTION |
| Парткод: | 302K339050 |
| Деталь: | SCREW OP / M3 X 8 CRFREE A4 |
| Парткод: | 5MMT263SN012++R |
| Деталь: | PARTS PWB DPIF ASSY SP |
| Парткод: | 303P294010 |
| Деталь: | WIRE PANEL DATA JOINT |
| Парткод: | 302N246010 |
| Деталь: | PARTS PWB ENGINE ASSY SP |
| Парткод: | 302N794100 |
| Деталь: | PARTS UNIT HIGH VOLTAGE MAIN SP |
| Парткод: | 302LF94260 |
| Деталь: | WIRE FFC FEED1 |
| Парткод: | 302N446170 |
| Деталь: | WIRE FFC FEED2 |
| Парткод: | 302N446180 |
| Деталь: | WIRE FFC FEED3 |
| Парткод: | 302N446190 |
| Деталь: | PARTS PWB FEED 1 ASSY SP |
| Парткод: | 302N494160 |
| Деталь: | WIRE FFC MAIN-ENGINE |
| Парткод: | 302N246040 |
| Деталь: | PARTS UNIT LOW VOLTAGE SP |
| Парткод: | 302N494080 |
| Деталь: | PLATE PWB LVU |
| Парткод: | 302N739060 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | COVER WIRE EJECT |
| Парткод: | 303JY28390 |
| Деталь: | PLATE OPTION COIN-VENDOR |
| Парткод: | 302K939431 |
| Деталь: | WIRE PF JOINT |
| Парткод: | 302LF46A70 |
| Деталь: | WIRE PF CASSETTE HEATER |
| Парткод: | 302K946A60 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | WIRE MAIN-LVU |
| Парткод: | 302N446070 |
| Деталь: | WIRE LVU RIGHT |
| Парткод: | 302N446110 |
| Деталь: | GUIDE FFC FEED 1 |
| Парткод: | 302K939141 |
| Деталь: | PLATE PWB FEED |
| Парткод: | 302K939150 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610004++H01 |
| Деталь: | WIRE FEED JOINT |
| Парткод: | 302K946571 |
| Деталь: | WIRE USB HOST JOINT |
| Парткод: | 302N246100 |
| Деталь: | WIRE MAIN-OPERATION |
| Парткод: | 302N246020 |
| Деталь: | MOUNT DRAWER A |
| Парткод: | 302K924340 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC60M2199+H01 |
| Деталь: | PIN DRAWER |
| Парткод: | 302K924350 |
| Деталь: | WIRE DU JOINT |
| Парткод: | 302N746120 |
| Деталь: | MOUNT DRAWER B |
| Парткод: | 302K924380 |
| Деталь: | SPRING DRAWER |
| Парткод: | 302K924360 |
| Деталь: | SHEET COVER FUSER PWB |
| Парткод: | 302LC02780 |
| Деталь: | SHEET PWB HVU MAIN |
| Парткод: | 302LF02410 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | SHEET WIRE HVU MAIN |
| Парткод: | 302LF39090 |
| Деталь: | FILM WIRE ENGINE |
| Парткод: | 302LF39070 |
| Деталь: | HOLDER ATTACHMENT |
| Парткод: | 302K931210 |
| Деталь: | WIRE HVU DLP |
| Парткод: | 302LH46330 |
| Деталь: | WIRE T1 POWER |
| Парткод: | 302LF46950 |
| Деталь: | WIRE BRIDGE JOINT |
| Парткод: | 302N446290 |
| Деталь: | WIRE CASSETTE HEATER |
| Парткод: | 302LF46890 |
| Деталь: | GUIDE FFC FEED 2 |
| Парткод: | 302K939170 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | WIRE ENGINE POWER |
| Парткод: | 302K946960 |
| Деталь: | WIRE KEY COUNTER |
| Парткод: | 302K946AJ0 |
| Деталь: | ACTUATOR EJECT SW |
| Парткод: | 303M429040 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | PARTS ROLLER EJECT SP |
| Парткод: | 303M494110 |
| Деталь: | GEAR CIS ROLLER 20 |
| Парткод: | 3H622020 |
| Деталь: | RING STOPPER/A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR Z33 |
| Парткод: | 303M407110 |
| Деталь: | PULLEY SEPARATION |
| Парткод: | 303LL07190 |
| Деталь: | TORQUE LIMITER FEED |
| Парткод: | 303JX07400 |
| Деталь: | RING STOPPER 4 |
| Парткод: | 5MVL177DN001 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 303NW94040 |
| Деталь: | JOINT RETARD DRIVE |
| Парткод: | 302K906180 |
| Деталь: | PARTS PWB LED ASSY SP |
| Парткод: | 303M894100 |
| Деталь: | COLLAR PF A |
| Парткод: | 3H607030 |
| Деталь: | PULLEY LF |
| Парткод: | 303M407480 |
| Цена: | 5 000 ₽ |
| Деталь: | FILM TORQUE LIMITER |
| Парткод: | 303MW07060 |
| Деталь: | PULLEY GUIDE READING |
| Парткод: | 303LL24190 |
| Деталь: | PARTS GUIDE SEPARATE ASSY SP |
| Парткод: | 303M494200 |
| Деталь: | SPRING CURSOR R |
| Парткод: | 2C907360 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | BUSHING PF HOLDER |
| Парткод: | 303H607131 |
| Деталь: | PULLEY TENSION |
| Парткод: | 303H607280 |
| Деталь: | STATIC ELIMINATOR EJECT |
| Парткод: | 303K502130 |
| Деталь: | BELT PF |
| Парткод: | 303LL07531 |
| Цена: | 1 900 ₽ |
| Деталь: | PULLEY 20 |
| Парткод: | 303M407080 |
| Деталь: | PULLEY HOLDER LF |
| Парткод: | 303M407200 |
| Деталь: | PULLEY 20 LF |
| Парткод: | 303M407220 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 2FB07330 |
| Деталь: | SEAL WIRE |
| Парткод: | 303K502070 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | COVER PF ROLLER |
| Парткод: | 303M407021 |
| Деталь: | Label JAM |
| Парткод: | 303M434051 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | COUPLING PRIMARY FEED DRIVE |
| Парткод: | 302K906140 |
| Деталь: | SHAFT GUIDE READING |
| Парткод: | 303M824130 |
| Деталь: | SPRING-TORSION SWITCHBACK |
| Парткод: | 302K928190 |
| Деталь: | STAY LOOP UPPER |
| Парткод: | 303M402070 |
| Деталь: | GUIDE UPPER |
| Парткод: | 303M407011 |
| Деталь: | HOLDER LF |
| Парткод: | 303M407030 |
| Деталь: | HOLDER PF |
| Парткод: | 303M407040 |
| Деталь: | COLLAR PF B |
| Парткод: | 303M407050 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SHAFT BELT |
| Парткод: | 303M407060 |
| Деталь: | BELT 172 LF |
| Парткод: | 303M407090 |
| Деталь: | GUIDE LOWER PF |
| Парткод: | 303M407101 |
| Деталь: | WIRE FEED UNIT |
| Парткод: | 303M446030 |
| Деталь: | SPRING EARTH |
| Парткод: | 303M407150 |
| Деталь: | SPRING HOLDER LF |
| Парткод: | 303M407160 |
| Деталь: | SHAFT LF |
| Парткод: | 303M407210 |
| Деталь: | HOOK COVER |
| Парткод: | 303M407231 |
| Деталь: | SHAFT HOOK |
| Парткод: | 303M407240 |
| Деталь: | SPRING HOOK FRONT |
| Парткод: | 303M407421 |
| Деталь: | SHAFT PULLEY TENSION |
| Парткод: | 303M407440 |
| Деталь: | SLIDER TENSION |
| Парткод: | 303M407450 |
| Деталь: | GUIDE EJECT LOWER |
| Парткод: | 303M424231 |
| Деталь: | GUIDE EJECT UPPER |
| Парткод: | 303M429020 |
| Деталь: | PLATE EARTH EJECT |
| Парткод: | 303M429030 |
| Деталь: | WIRE LED |
| Парткод: | 303M446070 |
| Деталь: | SPRING BELT TENTION |
| Парткод: | 303M407540 |
| Деталь: | PLATE EARTH SHAFT PF |
| Парткод: | 303M407550 |
| Деталь: | RING STOPPER 6 |
| Парткод: | 5MVL177DN002 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | MOUNT SENSOR RX |
| Парткод: | 303M407140 |
| Деталь: | PARTS PWB TX ASSY SP |
| Парткод: | 303M494150 |
| Деталь: | PARTS PWB RX ASSY SP |
| Парткод: | 303M494160 |
| Деталь: | PARTS PWB TX-RX SET SP |
| Парткод: | 303M494190 |
| Деталь: | STOPPER HF |
| Парткод: | 303NF06150 |
| Деталь: | BUSH FEED HF |
| Парткод: | 303NF06330 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | ACTUATOR HF |
| Парткод: | 303NF06040 |
| Деталь: | PARTS ROLLER CONVEYING DECK SP |
| Парткод: | 303NF94100 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | GUIDE HF LOWER |
| Парткод: | 303NF06010 |
| Деталь: | LABEL DECK B1 |
| Парткод: | 303NF34100 |
| Деталь: | CUSHION ACTUATOR |
| Парткод: | 303NF06340 |
| Деталь: | PLATE HF ROLLER |
| Парткод: | 303NF06060 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | SPRING ACT DU |
| Парткод: | 302H729120 |
| Деталь: | PIN HF LOWER |
| Парткод: | 303NF06270 |
| Деталь: | WIRE LEFT DECK 2 |
| Парткод: | 303NF46220 |
| Деталь: | LID WIRE |
| Парткод: | 303NF06260 |
| Деталь: | PLATE HF L |
| Парткод: | 303NF06050 |
| Деталь: | GUIDE HF LEFT |
| Парткод: | 303NF06030 |
| Деталь: | RAIL HF LEFT |
| Парткод: | 303NF06020 |
| Деталь: | SLIDER HF RAIL |
| Парткод: | 303NF06070 |
| Деталь: | COVER FEED LEFT |
| Парткод: | 303NF06250 |
| Деталь: | RAIL HF LOWER |
| Парткод: | 303NF06282 |
| Деталь: | SLIDER HF FRONT |
| Парткод: | 303NF06301 |
| Деталь: | GUIDE HF UPPER |
| Парткод: | 303NF06080 |
| Деталь: | LABEL DECK B2 |
| Парткод: | 303NF34110 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 302K906510 |
| Деталь: | PULLEY MIDDLE A |
| Парткод: | 302H722760 |
| Деталь: | SPRING DECK FEED |
| Парткод: | 303NF06320 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | LEVER HF UPPER |
| Парткод: | 303NF06180 |
| Деталь: | SPRING LOCK MPF |
| Парткод: | 302F708310 |
| Деталь: | STAY GUIDE UPPER |
| Парткод: | 303NF06310 |
| Деталь: | PARTS IMAGE SCANNER L SP |
| Парткод: | 302N693020 |
| Деталь: | SENSOR ORIGINAL |
| Парткод: | 302H044110 |
| Деталь: | PARTS MOUNT LED ASSY SP |
| Парткод: | 302N493040 |
| Деталь: | PARTS CONTACT-GLASS ASSY(I) SP |
| Парткод: | 302K994030 |
| Деталь: | PARTS CONTACT-GLASS ASSY(C) SP |
| Парткод: | 302K994040 |
| Деталь: | PARTS PWB ISC ASSY SP |
| Парткод: | 302N494201 |
| Деталь: | WIRE FFC CCD |
| Парткод: | 302K946670 |
| Деталь: | WIRE FFC LED |
| Парткод: | 302K946710 |
| Деталь: | COVER ISU FRONT |
| Парткод: | 302K904113 |
| Деталь: | COVER ISU LEFT |
| Парткод: | 302LC04130 |
| Деталь: | COVER ISU RIGHT |
| Парткод: | 302LC04141 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | MOUNT LEFT PULLEY |
| Парткод: | 302KK17031 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302H717160 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | PLATE PULLEY |
| Парткод: | 302GR17861 |
| Деталь: | PULLEY LEFT FRAME |
| Парткод: | 302K917150 |
| Деталь: | PIN WIRE PULLEY B |
| Парткод: | 302GR17350 |
| Деталь: | GUIDE WIRE ISU |
| Парткод: | 302K917381 |
| Деталь: | MOUNT DP HINGE |
| Парткод: | 302N217010 |
| Деталь: | BEARING 688ZZ |
| Парткод: | 7BE008165431H01 |
| Деталь: | HOLDER BEARING 688ZZ |
| Парткод: | 302K931960 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PULLEY ISU Z59 |
| Парткод: | 302K917021 |
| Деталь: | DRUM PULLEY |
| Парткод: | 302H717252 |
| Деталь: | WIRE SCANNER FRONT |
| Парткод: | 302H717381 |
| Деталь: | WIRE SCANNER REAR |
| Парткод: | 302H717391 |
| Деталь: | SHAFT ISU |
| Парткод: | 302K917060 |
| Деталь: | FRAME MIRROR B |
| Парткод: | 302K917091 |
| Деталь: | MIRROR B |
| Парткод: | 2FB12180 |
| Деталь: | MIRROR HOLDER |
| Парткод: | 75712080 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302H017180 |
| Деталь: | PLATE ADJUST B |
| Парткод: | 302K317830 |
| Деталь: | GUIDE FFC LED B |
| Парткод: | 302K317160 |
| Деталь: | SLIDER SCANNER |
| Парткод: | 2DC12230 |
| Деталь: | WIRE SCANNER MOTOR |
| Парткод: | 302N446240 |
| Деталь: | PLATE SLIT PI |
| Парткод: | 302K917080 |
| Деталь: | SPRING SCANNER TENSION |
| Парткод: | 302C912291 |
| Деталь: | FRAME MIRROR A |
| Парткод: | 302K317062 |
| Деталь: | MIRROR A |
| Парткод: | 302KK17320 |
| Деталь: | SPRING,MIRROR HOLDER |
| Парткод: | 2BC12190 |
| Деталь: | RETAINER WIRE |
| Парткод: | 2C912150 |
| Деталь: | GUIDE FFC LED C |
| Парткод: | 302K317172 |
| Деталь: | SHEET FFC LED |
| Парткод: | 302K317791 |
| Деталь: | GUIDE FFC LED D |
| Парткод: | 302K317310 |
| Деталь: | MOUNT RELEASE SWITCH |
| Парткод: | 302K917130 |
| Деталь: | SWITCH RELEASE |
| Парткод: | 302K917120 |
| Деталь: | SPRING RELEASE SWITCH |
| Парткод: | 302GR17380 |
| Деталь: | BELT ISU |
| Парткод: | 302K917040 |
| Деталь: | PARTS MOTOR ISU SP |
| Парткод: | 302N294010 |
| Деталь: | MOUNT ISU DRIVE |
| Парткод: | 302K917030 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | WIRE CCD POWER |
| Парткод: | 302K946680 |
| Деталь: | WIRE ORIGINAL SENSOR |
| Парткод: | 302K946750 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBFZZ65C001H01 |
| Деталь: | MOUNT PWB |
| Парткод: | 302K917230 |
| Деталь: | LK-6707 |
| Парткод: | 302N793010 |
| Деталь: | GUIDE WIRE FRONT PWB |
| Парткод: | 302LF39050 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | WIRE OPEN SENSOR |
| Парткод: | 302K946730 |
| Деталь: | WIRE HP SENSOR |
| Парткод: | 302K946A90 |
| Деталь: | MOUNT PI |
| Парткод: | 302K317330 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | COVER ISU |
| Парткод: | 302K917400 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSSTG58014H01 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+010H01 |
| Деталь: | SEAL FRAME SIDE B |
| Парткод: | 302H717440 |
| Деталь: | FILM FRAME |
| Парткод: | 302K317660 |
| Деталь: | SEAL FRAME ISU C |
| Парткод: | 302K317650 |
| Деталь: | SEAL FRAME ISU A |
| Парткод: | 302K317450 |
| Деталь: | SEAL FRAME ISU B |
| Парткод: | 302K317460 |
| Деталь: | WIRE CCD DATA |
| Парткод: | 302K946700 |
| Деталь: | WIRE ISC-MAIN |
| Парткод: | 302K946720 |
| Деталь: | FILM FRAME SIDE F |
| Парткод: | 302K917170 |
| Деталь: | FILM FRAME SIDE R |
| Парткод: | 302K917180 |
| Деталь: | CAP PULLEY ISU |
| Парткод: | 302K917240 |
| Деталь: | PIN SCANNER RETAINING |
| Парткод: | 302GR17180 |
| Деталь: | GUIDE WIRE USB |
| Парткод: | 302N239010 |
| Деталь: | GUIDE WIRE OPERATION |
| Парткод: | 302LC05350 |
| Деталь: | PIN ISU FRONT |
| Парткод: | 302N404410 |
| Деталь: | LABEL CAUTION B |
| Парткод: | 303M434230 |
| Деталь: | COVER REAR |
| Парткод: | 303M404021 |
| Деталь: | CLOTH CLEANING |
| Парткод: | 302N904100 |
| Деталь: | LID REAR COVER |
| Парткод: | 303M404161 |
| Деталь: | COVER LEFT |
| Парткод: | 303M404051 |
| Деталь: | COVER INNER |
| Парткод: | 303M404060 |
| Деталь: | LABEL C |
| Парткод: | 303M434040 |
| Деталь: | COVER FRONT |
| Парткод: | 303M404011 |
| Деталь: | HANDLE FRONT COVER |
| Парткод: | 303M404130 |
| Деталь: | PLATE ORIGINAL |
| Парткод: | 303JC04201 |
| Деталь: | CUSHION ORIGINAL MAT A |
| Парткод: | 303MX02021 |
| Деталь: | COVER WIRE INTERFACE |
| Парткод: | 303M404111 |
| Деталь: | COVER HINGE LEFT |
| Парткод: | 303M404070 |
| Деталь: | COVER HINGE RIGHT |
| Парткод: | 303M404080 |
| Деталь: | PARTS MAT ASSY |
| Парткод: | 303LL94032 |
| Деталь: | CASE WASTE BOTTLE |
| Парткод: | 302K904490 |
| Деталь: | COVER ISU LEFT INNER |
| Парткод: | 302K904050 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302K904121 |
| Деталь: | COVER OPERATION MOUNT C |
| Парткод: | 302K904571 |
| Деталь: | COVER ISU LEFT SUB |
| Парткод: | 302LC04340 |
| Деталь: | MAGNET CLIP DISH |
| Парткод: | 302GR04370 |
| Деталь: | LABEL OPERATION CAUTION B |
| Парткод: | 302LC34031 |
| Деталь: | FILTER TOP |
| Парткод: | 302N433010 |
| Цена: | 5 000 ₽ |
| Деталь: | COVER FILTER EXIT |
| Парткод: | 302K933181 |
| Деталь: | COVER LEFT UPPER |
| Парткод: | 302LF04043 |
| Деталь: | PARTS FILTER FAN ASSY(Z) SP |
| Парткод: | 302LF94300 |
| Деталь: | LID LEFT COVER REAR |
| Парткод: | 302LC04110 |
| Деталь: | FILTER LEFT SIDE |
| Парткод: | 302LC33370 |
| Цена: | 3 900 ₽ |
| Деталь: | LID CONTROLLER |
| Парткод: | 302K904150 |
| Деталь: | COVER CONTROLLER |
| Парткод: | 302K904140 |
| Деталь: | FILTER DU |
| Парткод: | 302H722870 |
| Деталь: | LABEL ENERGY STAR |
| Парткод: | 302N434050 |
| Деталь: | COVER RIGHT FRONT |
| Парткод: | 302K929391 |
| Деталь: | COVER INNER CONVEYING FRONT |
| Парткод: | 302N729671 |
| Деталь: | HOLDER MAGNET |
| Парткод: | 303NB24210 |
| Деталь: | SEAL MAGNET |
| Парткод: | 302GR04380 |
| Деталь: | COVER FRONT TOP |
| Парткод: | 302N204010 |
| Деталь: | MOUNT TABLE |
| Парткод: | 302N204020 |
| Деталь: | GLASS TABLE |
| Парткод: | 302N204060 |
| Деталь: | MOUNT GLASS TABLE |
| Парткод: | 302N204070 |
| Деталь: | STAY TABLE GLASS |
| Парткод: | 302N204080 |
| Деталь: | RETAINER GLASS TABLE |
| Парткод: | 302N204100 |
| Деталь: | MOUNT TABLE MIDDLE |
| Парткод: | 302N204110 |
| Деталь: | LID TOP KEYBOARD |
| Парткод: | 302N204120 |
| Деталь: | SHEET GLASS TABLE |
| Парткод: | 302N204130 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | LID TOP LEFT |
| Парткод: | 302N204050 |
| Деталь: | SPRING USB HOLD |
| Парткод: | 302K905900 |
| Деталь: | MOUNT USB |
| Парткод: | 302N204090 |
| Деталь: | WIRE USB KEYBOARD |
| Парткод: | 302N246120 |
| Деталь: | WIRE USB CARD READER |
| Парткод: | 302N246130 |
| Деталь: | LID TOP RIGHT |
| Парткод: | 302N204040 |
| Деталь: | COVER TOP LID RIGHT |
| Парткод: | 302N204170 |
| Деталь: | SHEET LEFT COVER |
| Парткод: | 302N704020 |
| Деталь: | SEAL LSU DUCT |
| Парткод: | 302LF04050 |
| Деталь: | PARTS FILTER BELT UNIT(V) SP |
| Парткод: | 302LC94130 |
| Деталь: | MOUNT WASTE BOTTLE COVER |
| Парткод: | 302K904340 |
| Деталь: | PARTS FILTER EXIT UNIT SP |
| Парткод: | 302K994101 |
| Цена: | 4 300 ₽ |
| Деталь: | PARTS COVER RIGHT FRONT SP |
| Парткод: | 302N794130 |
| Деталь: | PARTS GLASS TABLE ASSY SP |
| Парткод: | 302N794070 |
| Деталь: | PARTS PWB JOB SEPA ASSY SP |
| Парткод: | 302K994600 |
| Деталь: | LABEL JOB SEPARATOR |
| Парткод: | 302K934190 |
| Деталь: | PARTS MOTOR PM FEED SP |
| Парткод: | 302K994300 |
| Деталь: | PARTS ROLLER EXIT RIGHT SP |
| Парткод: | 303NM94010 |
| Деталь: | TRAY EXIT A |
| Парткод: | 303NM16101 |
| Деталь: | TRAY EXIT B |
| Парткод: | 303NM16111 |
| Деталь: | TRAY EXIT C |
| Парткод: | 303NM16120 |
| Деталь: | GEAR Z46R Z21S IDLE |
| Парткод: | 303NM16130 |
| Деталь: | GEAR Z15S |
| Парткод: | 303NM16140 |
| Деталь: | TRAY EXIT D |
| Парткод: | 303NM16230 |
| Деталь: | ACTUATOR EXIT |
| Парткод: | 303NM16280 |
| Деталь: | PARTS SOLENOID JS SP |
| Парткод: | 303NM94020 |
| Деталь: | WIRE INTERFACE |
| Парткод: | 303NM46010 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | 63212210 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | FRAME EXIT |
| Парткод: | 303NM16010 |
| Деталь: | PULLEY MPT BYPASS |
| Парткод: | 302FZ07020 |
| Деталь: | SPRING PULLEY JS |
| Парткод: | 303MA16290 |
| Деталь: | SPRING-TORSION GUIDE F |
| Парткод: | 303NM16170 |
| Деталь: | SPRING-TORSION GUIDE R |
| Парткод: | 303NM16180 |
| Деталь: | SPRING EARTH A |
| Парткод: | 303NM16190 |
| Деталь: | SPRING EARTH B |
| Парткод: | 303NM16240 |
| Деталь: | GUIDE EXIT B |
| Парткод: | 303NM16030 |
| Деталь: | PLATE GUIDE LOWER |
| Парткод: | 303NM16250 |
| Деталь: | SPRING-EXTENSION |
| Парткод: | 303NM16210 |
| Деталь: | STUD SCREW M3 |
| Парткод: | 302F325010 |
| Деталь: | ARM FEED SHIFT |
| Парткод: | 303NM16200 |
| Деталь: | PLATE EXIT F |
| Парткод: | 303NM16041 |
| Деталь: | PLATE EXIT R |
| Парткод: | 303NM16050 |
| Деталь: | ARM SENSOR |
| Парткод: | 303NM16300 |
| Деталь: | WIRE JOB SEPARATOR |
| Парткод: | 303NM46020 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | HOLDER SENSOR |
| Парткод: | 303NM16290 |
| Деталь: | Cover Upper |
| Парткод: | 303NM16271 |
| Деталь: | COVER EXIT F |
| Парткод: | 303NM16220 |
| Деталь: | COVER PWB EXIT |
| Парткод: | 303NM16150 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 2FB07330 |
| Деталь: | SPRING RELEASE COVER |
| Парткод: | 303JY24640 |
| Деталь: | GUIDE EXIT A |
| Парткод: | 303NM16020 |
| Деталь: | STAY GUIDE LOWER |
| Парткод: | 303NM16260 |
| Деталь: | LEVER EXIT RIGHT |
| Парткод: | 303NM16080 |
| Деталь: | SHAFT LEVER EXIT |
| Парткод: | 303NM16070 |
| Деталь: | HOOK LEVER JAM JS F |
| Парткод: | 303MA16570 |
| Деталь: | SPRING EXIT PUSH |
| Парткод: | 302FZ28270 |
| Деталь: | PLATE EXIT LOWER |
| Парткод: | 303NM16060 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | COVER DECK RIGHT |
| Парткод: | 302K904270 |
| Деталь: | COVER DECK LEFT |
| Парткод: | 302K904300 |
| Деталь: | HANDLE DECK RIGHT |
| Парткод: | 302K904280 |
| Деталь: | HANDLE DECK LEFT |
| Парткод: | 302K904310 |
| Деталь: | EMBLEM DECK RIGHT |
| Парткод: | 302K904290 |
| Деталь: | EMBLEM DECK LEFT |
| Парткод: | 302K904550 |
| Деталь: | LABEL CASSETTE NUMBER 3 |
| Парткод: | 302K934070 |
| Деталь: | LABEL CASSETTE NUMBER 4 |
| Парткод: | 302K934080 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | GEAR 20 |
| Парткод: | 2BC07110 |
| Деталь: | CURSOR END DECK |
| Парткод: | 303NF10070 |
| Деталь: | CURSOR DECK FRONT |
| Парткод: | 303NF10080 |
| Деталь: | CURSOR DECK REAR |
| Парткод: | 303NF10090 |
| Деталь: | GEAR DAMPER 100 |
| Парткод: | 303NF10160 |
| Деталь: | WIRE LIFT A |
| Парткод: | 303NF10180 |
| Деталь: | WIRE LIFT B |
| Парткод: | 303NF10190 |
| Деталь: | STOPPER PULLEY |
| Парткод: | 303NF10220 |
| Деталь: | CURSOR END SUB |
| Парткод: | 303NF10410 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | FRONT PULLEY, LIFT DRIVE |
| Парткод: | 2BC07020 |
| Деталь: | LABEL DECK PAPER DIRECTION |
| Парткод: | 303NF34030 |
| Деталь: | LABEL DECK OPERATION B |
| Парткод: | 303NF34020 |
| Деталь: | LABEL DECK SIZE B |
| Парткод: | 303NF34060 |
| Деталь: | LABEL DECK SIZE D |
| Парткод: | 303NF34080 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09991 |
| Деталь: | DECK CASSETTE |
| Парткод: | 303NF10012 |
| Деталь: | PLATE EARTH REAR |
| Парткод: | 303NF10430 |
| Деталь: | WIRE EARTH B |
| Парткод: | 303NF10450 |
| Деталь: | WIRE EARTH A |
| Парткод: | 303NF10440 |
| Деталь: | PLATE EARTH FRONT |
| Парткод: | 303NF10420 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 303NF10320 |
| Деталь: | PLATE LIFT DECK |
| Парткод: | 303NF10051 |
| Деталь: | SPACER,DECK LIFT |
| Парткод: | 2BC07120 |
| Деталь: | STATIC ELIMINATOR CURSOR |
| Парткод: | 303JY37220 |
| Деталь: | PAD,LIFT |
| Парткод: | 3A707290 |
| Деталь: | LABEL DECK OPERATION A |
| Парткод: | 303NF34011 |
| Деталь: | PULLEY LIFT WIRE |
| Парткод: | 303NF10300 |
| Деталь: | MOUNT DECK DAMPER |
| Парткод: | 303NF10140 |
| Деталь: | SPRING LIFT STOPPER |
| Парткод: | 303NF10170 |
| Деталь: | DAMPER |
| Парткод: | 302G404160 |
| Деталь: | PLATE DECK SUB |
| Парткод: | 303NF10100 |
| Деталь: | PLATE WIRE LOCK |
| Парткод: | 303NF10150 |
| Деталь: | MOUNT CURSOR ADJUST |
| Парткод: | 303NF10390 |
| Деталь: | MOUNT CURSOR |
| Парткод: | 303NF10110 |
| Деталь: | PIN CURSOR LOCK |
| Парткод: | 303NF10250 |
| Деталь: | SHAFT DECK LIFT |
| Парткод: | 303NF10130 |
| Деталь: | LABEL DECK PAPER LIMIT |
| Парткод: | 303NF34040 |
| Деталь: | PARTS DECK UNIT(INCHI) SP |
| Парткод: | 302N294060 |
| Деталь: | PARTS DECK UNIT SP |
| Парткод: | 302N294050 |
| Деталь: | COVER BOTTOM RIGHT |
| Парткод: | 303M404100 |
| Деталь: | TRAY EJECT |
| Парткод: | 303M404040 |
| Деталь: | TRAY SLIDE |
| Парткод: | 303M404121 |
| Деталь: | Hinge Left |
| Парткод: | 303M402021 |
| Деталь: | Hinge Right |
| Парткод: | 303M402031 |
| Деталь: | SPRING PUSH SW |
| Парткод: | 303JX02090 |
| Деталь: | PUSH SW |
| Парткод: | 303LL02390 |
| Деталь: | STOPPER EJECT |
| Парткод: | 303M404170 |
| Деталь: | PIN HINGE |
| Парткод: | 303JX02260 |
| Деталь: | PLATE ANGLE |
| Парткод: | 303M402170 |
| Деталь: | SHAFT ANGLE RESTRICTION |
| Парткод: | 303JX02391 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PLATE GUIDE HINGE |
| Парткод: | 303LL02380 |
| Деталь: | PLATE GUIDE HINGE |
| Парткод: | 303M402200 |
| Деталь: | STAY EJECT TRAY |
| Парткод: | 303M402190 |
| Деталь: | MOUNT CUSHION |
| Парткод: | 303LL02410 |
| Деталь: | SPRING PUSH MAT |
| Парткод: | 303LL02430 |
| Деталь: | CUSHION ORIGINAL MAT |
| Парткод: | 303LL02530 |
| Деталь: | PLATE HINGE UPPER |
| Парткод: | 303M402180 |
| Деталь: | HOLDER SPRING PUSH SW |
| Парткод: | 303LL02150 |
| Деталь: | GEAR Z28 FEED |
| Парткод: | 302N406170 |
| Деталь: | PULLEY FEED |
| Парткод: | 302N406030 |
| Цена: | 440 ₽ |
| Деталь: | GEAR Z32 FEED OW |
| Парткод: | 302N406100 |
| Деталь: | GEAR Z32 PICKUP |
| Парткод: | 302N406110 |
| Деталь: | SPRING SWITCHBACK |
| Парткод: | 302LC28240 |
| Деталь: | PLATE FRAME UPPER |
| Парткод: | 302N406010 |
| Деталь: | PLATE FRAME LOWER |
| Парткод: | 302N406020 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302K906321 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 302K906510 |
| Деталь: | PARTS ROLLER ASSIST SP |
| Парткод: | 302K994420 |
| Деталь: | SHEET SOLENOID |
| Парткод: | 303NF06350 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | COUPLING DRIVE |
| Парткод: | 302K931530 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 302K994580 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | PULLEY RETARD |
| Парткод: | 302N406040 |
| Цена: | 450 ₽ |
| Деталь: | LEVER RETARD LOCK |
| Парткод: | 302N406160 |
| Деталь: | PLATE RETARD ADJUST |
| Парткод: | 302K906420 |
| Деталь: | SPRING LOCK MPF |
| Парткод: | 302F708310 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 302K906700 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | SHAFT ASSIST PULLEY |
| Парткод: | 302K906710 |
| Деталь: | HOLDER RETARD |
| Парткод: | 302K906151 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | LOWER BUSHING,PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | TORQUE-LIMITER 390 |
| Парткод: | 302K906750 |
| Деталь: | PLATE RETARD HOLDER |
| Парткод: | 302K906300 |
| Деталь: | FULCRUM-PIN RETARD |
| Парткод: | 302N406150 |
| Деталь: | LEVER RETARD RELEASE |
| Парткод: | 302N406130 |
| Деталь: | SPRING RETARD |
| Парткод: | 302N406200 |
| Деталь: | SHEET PRIMARY FEED HI |
| Парткод: | 302K906721 |
| Деталь: | GUIDE PRIM FEED WIRE |
| Парткод: | 302K906250 |
| Деталь: | WIRE PRIMARY FEED UNIT |
| Парткод: | 302N446280 |
| Деталь: | GUIDE FRONT LOWER |
| Парткод: | 302N406060 |
| Деталь: | SPRING RETARD LOCK |
| Парткод: | 302N406140 |
| Деталь: | HOLDER SENSOR FEED |
| Парткод: | 302K906290 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | HOLDER PICKUP |
| Парткод: | 302N406050 |
| Деталь: | PIN PICK UP IDLE |
| Парткод: | 302K906080 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | SHAFT PICKUP PRIMARY |
| Парткод: | 302N406070 |
| Деталь: | ONEWAY-CLUTCH 6 |
| Парткод: | 302N406120 |
| Деталь: | SPRING PICK UP |
| Парткод: | 302K906260 |
| Деталь: | PLATE PRIMARY FEED DRIVE |
| Парткод: | 302K906111 |
| Деталь: | COUPLING PRIMARY FEED DRIVE |
| Парткод: | 302K906140 |
| Деталь: | MOUNT PRIMARY FEED R |
| Парткод: | 302K906270 |
| Деталь: | HOLDER PRIM FEED PULLEY |
| Парткод: | 302K906280 |
| Деталь: | GUIDE PRIMARY FEED |
| Парткод: | 302K906051 |
| Деталь: | CUSHION,CONTACT GLASS |
| Парткод: | 29812291 |
| Деталь: | MOUNT PRIMARY FEED |
| Парткод: | 302K906100 |
| Деталь: | PARTS PRIMARY FEED UNIT HI SP |
| Парткод: | 302N494020 |
| Цена: | 14 600 ₽ |
| Деталь: | PARTS GUIDE PRIMARY FEED SET SP |
| Парткод: | 302K994B90 |
| Деталь: | PULLEY MID /B-11 FRAMEA4 |
| Парткод: | 2FM02210 |
| Деталь: | GEAR Z40R-Z28S |
| Парткод: | 302K928110 |
| Деталь: | CAP SPRING /B-11 ENCLOSUREA4 |
| Парткод: | 2FM04150 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | Plate Earth FD |
| Парткод: | 302K928200 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | GEAR Z23S EXIT |
| Парткод: | 302H728080 |
| Деталь: | SPRING PULLEY A |
| Парткод: | 302HN28120 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | SPRING-TORSION SWITCHBACK |
| Парткод: | 302K928190 |
| Деталь: | PARTS MOTOR PM FEED SP |
| Парткод: | 302K994300 |
| Деталь: | PARTS SOLENOID FEED SHIFT SP |
| Парткод: | 302K994370 |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 302K994910 |
| Деталь: | GEAR Z20S JOINT FEED B |
| Парткод: | 302H006120 |
| Деталь: | FRAME EXIT UPPER |
| Парткод: | 302K928021 |
| Деталь: | SPRING-EXTENSION FEED SHIFT |
| Парткод: | 302K928070 |
| Деталь: | SPRING-EXTENSION |
| Парткод: | 302LC28110 |
| Деталь: | SPRING PULLEY |
| Парткод: | 302F928170 |
| Деталь: | ACTUATOR SWITCHBACK |
| Парткод: | 302K928091 |
| Деталь: | WIRE EXIT |
| Парткод: | 302K946360 |
| Деталь: | RING STOPPER/A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | PARTS ROLLER EXIT B SP |
| Парткод: | 302K994A40 |
| Деталь: | FRAME EXIT LOWER |
| Парткод: | 302K928011 |
| Деталь: | GUIDE CHANGE LOWER |
| Парткод: | 302K928213 |
| Деталь: | GUIDE SHIFT UPPER |
| Парткод: | 302K928030 |
| Деталь: | PLATE EARTH ROLLER |
| Парткод: | 302K928170 |
| Деталь: | GUIDE EXIT MIDDLE |
| Парткод: | 302K928051 |
| Деталь: | SHEET EXIT MIDDLE A |
| Парткод: | 302K928290 |
| Деталь: | SHEET EXIT MIDDLE B |
| Парткод: | 302K928300 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 302JF22010 |
| Деталь: | ACTUATOR EXIT SENSOR |
| Парткод: | 302K928121 |
| Деталь: | PLATE DRIVE FD |
| Парткод: | 302K928131 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | STAY EXIT HIGH |
| Парткод: | 302K928230 |
| Деталь: | COVER FRONT |
| Парткод: | 302K928141 |
| Деталь: | PARTS EXIT UNIT A SP |
| Парткод: | 302K994662 |
| Деталь: | PARTS GUIDE EXIT MIDDLE SP |
| Парткод: | 302K994B80 |
| Деталь: | SLIDER CASSETTE RIGHT |
| Парткод: | 302N209501 |
| Деталь: | CAP HANDLE |
| Парткод: | 302FZ02580 |
| Деталь: | SEAL HANDLE |
| Парткод: | 302FZ03110 |
| Деталь: | SLIDER CASSETTE LEFT |
| Парткод: | 302N209511 |
| Деталь: | MOUNT SLIDER LF |
| Парткод: | 302N209530 |
| Деталь: | MOUNT SLIDER LR |
| Парткод: | 302N209540 |
| Деталь: | SLIDER CONVEYING |
| Парткод: | 302K924300 |
| Деталь: | MOUNT SLIDER CONVEYING |
| Парткод: | 302K924311 |
| Деталь: | MOUNT CONVEYING |
| Парткод: | 302LF29050 |
| Деталь: | FRAME FRONT FUSER A |
| Парткод: | 302N702170 |
| Деталь: | NUT ADJUST M2 |
| Парткод: | 302N204150 |
| Деталь: | DUCT CONTAINER RIGHT |
| Парткод: | 302LF33480 |
| Деталь: | MOUNT FUSER ADJUST A |
| Парткод: | 302N702210 |
| Деталь: | PLATE FUSER ADJUST |
| Парткод: | 302N702150 |
| Деталь: | STAY UPPER TOP RIGHT |
| Парткод: | 302K902220 |
| Деталь: | ADJUSTER SCANNER |
| Парткод: | 302K902950 |
| Деталь: | MOUNT RUBBER SCANNER |
| Парткод: | 302K902960 |
| Деталь: | GROUND SCANNER REAR |
| Парткод: | 302H017310 |
| Деталь: | PIN ROLLER RELEASE LEVER |
| Парткод: | 302FB16320 |
| Деталь: | STAY UPPER TOP LEFT |
| Парткод: | 302K902230 |
| Деталь: | FRAME FUSER UNIT |
| Парткод: | 302N702200 |
| Деталь: | SEAL DUCT CONTAINER R |
| Парткод: | 302LF33490 |
| Деталь: | PARTITION FIXING HEAT |
| Парткод: | 302LF33601 |
| Деталь: | SHEET COVER PWB FEED |
| Парткод: | 302K902990 |
| Деталь: | FILM BASE CASSETTE |
| Парткод: | 302K902571 |
| Деталь: | RAIL EXIT REAR |
| Парткод: | 302K902850 |
| Деталь: | REINFORCEMENT UPPER REAR |
| Парткод: | 302K902920 |
| Деталь: | LEVER RELEASE FUSER DRIVE |
| Парткод: | 302K931690 |
| Деталь: | SPRING LEVER RELEASE |
| Парткод: | 302K931980 |
| Деталь: | PLATE SHIELD BOX |
| Парткод: | 302K939080 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | RAIL CONTAINER L |
| Парткод: | 302LF03730 |
| Деталь: | RAIL CONTAINER R |
| Парткод: | 302LF03720 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSSTG58014H01 |
| Деталь: | PIN HOOK |
| Парткод: | 302K924450 |
| Деталь: | SEAL DUCT EXIT |
| Парткод: | 302LF33530 |
| Деталь: | FRAME FRONT FUSER B |
| Парткод: | 302K902162 |
| Деталь: | PLATE MOUNT DP |
| Парткод: | 302K902250 |
| Деталь: | BASE RUBBER,SCANNER SECTION |
| Парткод: | 2AV12280 |
| Деталь: | GROUND BASE SCANNER |
| Парткод: | 302H017380 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SHEET MOUNT FRONT COVER |
| Парткод: | 302LF04060 |
| Деталь: | PROTECTOR PLATE HANDLE |
| Парткод: | 302LC02810 |
| Деталь: | HANDLE RIGHT |
| Парткод: | 302LC02561 |
| Деталь: | SHAFT HOOK PULLEY |
| Парткод: | 302K909630 |
| Деталь: | LEVER CASSETTE HOOK |
| Парткод: | 302K909640 |
| Деталь: | SPRING CASSETTE HOOK |
| Парткод: | 302LH02050 |
| Деталь: | PULLEY EJECT |
| Парткод: | 303LW24060 |
| Деталь: | SHAFT HOOK FULCRUM |
| Парткод: | 303NF02280 |
| Деталь: | HOLDER DECK HOOK |
| Парткод: | 303NF02301 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | SEAL REGIST REAR |
| Парткод: | 302N733160 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | RETAINER OPERATION ARM |
| Парткод: | 302K905532 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | MOUNT FUSER ADJUST B |
| Парткод: | 302N702220 |
| Деталь: | SPONGE INNER LOWER |
| Парткод: | 302LF33350 |
| Деталь: | SPONGE LOWER RIGHT |
| Парткод: | 302LF33870 |
| Деталь: | MOUNT FRONT COVER |
| Парткод: | 302LF04030 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | MOUNT IH FRONT |
| Парткод: | 302N702180 |
| Деталь: | MOUNT IH REAR |
| Парткод: | 302N702190 |
| Деталь: | STAY CASSETTE FRONT |
| Парткод: | 302N209521 |
| Деталь: | PLATE CASSETTE HOLD |
| Парткод: | 302N209550 |
| Деталь: | COVER WIRE EJECT |
| Парткод: | 303JY28390 |
| Деталь: | PARTS SLIDER CASSETTE LEFT ASSY SP |
| Парткод: | 302N294020 |
| Деталь: | SPRING HV |
| Парткод: | 302K939360 |
| Деталь: | TERMINAL HV SEPARATION |
| Парткод: | 302LF39010 |
| Деталь: | COVER WIRE IH |
| Парткод: | 302N739040 |
| Деталь: | PARTS PWB EXIT ASSY SP |
| Парткод: | 302LF94230 |
| Деталь: | COVER PWB IH |
| Парткод: | 302K939450 |
| Деталь: | WIRE HEATER PWB |
| Парткод: | 302N946010 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PARTS MOTOR LIFT ASSY SP |
| Парткод: | 302K394190 |
| Цена: | 6 000 ₽ |
| Деталь: | PARTS PWB FRONT MONO ASSY SP |
| Парткод: | 302LF94210 |
| Деталь: | PARTS PWB LSU JUNC MONO ASSY SP |
| Парткод: | 302N994080 |
| Деталь: | WIRE FFC LSU |
| Парткод: | 302N946020 |
| Деталь: | GUIDE WIRE ISU |
| Парткод: | 302K939550 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | TERMINAL HV DRUM |
| Парткод: | 302LF39020 |
| Деталь: | SPRING HV DRUM |
| Парткод: | 302LF39080 |
| Деталь: | PARTS TONER FULL DETECT ASSY SP |
| Парткод: | 302K994150 |
| Деталь: | SHEET PWB FRONT |
| Парткод: | 302LF02500 |
| Деталь: | WIRE EXIT FAN |
| Парткод: | 302LF46140 |
| Деталь: | PLATE EARTH PANEL C |
| Парткод: | 302MC05080 |
| Деталь: | WIRE EXIT PWB JOINT |
| Парткод: | 302N746090 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | GUIDE WIRE INLET |
| Парткод: | 302K939381 |
| Деталь: | PLATE INLET |
| Парткод: | 302N739010 |
| Деталь: | PLATE INLET B2 |
| Парткод: | 302N439070 |
| Деталь: | WIRE INLET ASSY 1 |
| Парткод: | 302N446270 |
| Деталь: | WIRE HVU TC |
| Парткод: | 302LF46320 |
| Деталь: | WIRE HVU MC |
| Парткод: | 302LF46341 |
| Деталь: | WIRE JOBSEPARATOR JOINT |
| Парткод: | 302K946580 |
| Деталь: | Holder FFC |
| Парткод: | 302LF02380 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610017++H01 |
| Деталь: | GUIDE WIRE FRONT PWB |
| Парткод: | 302LF39050 |
| Деталь: | HOLDER PWB |
| Парткод: | 302K939230 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | WIRE FRONT POWER |
| Парткод: | 302LF46940 |
| Деталь: | PLATE MAIN SW |
| Парткод: | 302N439050 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302K994360 |
| Деталь: | DUCT FAN IH |
| Парткод: | 302K939560 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510022++H01 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | SW.SEESAW |
| Парткод: | 7SC020403+++H01 |
| Деталь: | WIRE INTERLOCK |
| Парткод: | 302K946530 |
| Деталь: | WIRE MAIN SWITCH |
| Парткод: | 302N946030 |
| Деталь: | ACCESS.BUSHING |
| Парткод: | 7YZM110001++H01 |
| Деталь: | WIRE CONTAINER JOINT |
| Парткод: | 302LF46630 |
| Деталь: | WIRE FUSER JOINT |
| Парткод: | 302N746080 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | GUIDE WIRE IH |
| Парткод: | 302N739030 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | WIRE LIFT MOTOR |
| Парткод: | 302K946410 |
| Деталь: | COVER WIRE FUSER |
| Парткод: | 302K939521 |
| Деталь: | WIRE HVU MAIN |
| Парткод: | 302N746110 |
| Деталь: | MOUNT PAPER LEVEL SENSOR |
| Парткод: | 302K909510 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | WIRE PAPER SENSOR |
| Парткод: | 302K946420 |
| Деталь: | MOUNT SIZE SENSOR |
| Парткод: | 302K909520 |
| Деталь: | HOLDER SIZE DETECTION |
| Парткод: | 302K909541 |
| Деталь: | PIN PAPER SIZE A |
| Парткод: | 302K909580 |
| Деталь: | PIN PAPER SIZE B |
| Парткод: | 302K909590 |
| Деталь: | PIN PAPER SIZE C |
| Парткод: | 302K909600 |
| Деталь: | WIRE CASSETTE SIZE |
| Парткод: | 302K946400 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP03072001+H01 |
| Деталь: | SPACER DU |
| Парткод: | 302F729080 |
| Деталь: | PARTS PWB CURRENT AVE ASSY SP |
| Парткод: | 302LC94270 |
| Деталь: | WIRE CURRENT PWB POWER |
| Парткод: | 302LH46150 |
| Деталь: | WIRE CURRENT PWB |
| Парткод: | 302LH46160 |
| Деталь: | AC CORD ASSY US |
| Парткод: | 7AAACCUS+20H002 |
| Деталь: | ACCESS.BUSHING |
| Парткод: | 7YZM120001++H01 |
| Деталь: | PARTS AC CORD EU SP |
| Парткод: | 302AR94050 |
| Деталь: | AC CORD ASSY AS |
| Парткод: | 7AAACCAS+10H001 |
| Деталь: | PARTS IH BOX ASSY J SP |
| Парткод: | 302N794030 |
| Деталь: | PARTS IH BOX ASSY E SP |
| Парткод: | 302N794040 |
| Деталь: | PARTS PAPER LEVEL SENSOR ASSY SP |
| Парткод: | 302K994C80 |
| Деталь: | PARTS SIZE DETECTION ASSY SP |
| Парткод: | 302K994121 |
| Деталь: | PARTS SENSOR A3 COLOR CIS(C) SP |
| Парткод: | 303P294020 |
| Деталь: | GLASS CIS |
| Парткод: | 303NW24020 |
| Деталь: | GEAR Z42 FEED |
| Парткод: | 2BL06170 |
| Деталь: | RING STOPPER/A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303NW94040 |
| Деталь: | PARTS PWB SHD(C) ASSY SP |
| Парткод: | 303M494033 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510019++H01 |
| Деталь: | WIRE INTERFACE VIDEO |
| Парткод: | 303M446020 |
| Деталь: | PULLEY REGISTRATION BK |
| Парткод: | 303M424300 |
| Деталь: | PULLEY REG B BK |
| Парткод: | 303M424310 |
| Деталь: | GEAR JOINT MPT UNIT |
| Парткод: | 302FZ08370 |
| Деталь: | GEAR IDLE Z14S |
| Парткод: | 2CK17050 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | PARTS ROLLER CIS SP |
| Парткод: | 303M494060 |
| Деталь: | HANDLE COVER PF |
| Парткод: | 303M404140 |
| Деталь: | LENS LED |
| Парткод: | 303M407300 |
| Деталь: | HOLDER LENS |
| Парткод: | 303M407400 |
| Деталь: | COVER PF |
| Парткод: | 303M404031 |
| Деталь: | PULLY CIS ROLLER |
| Парткод: | 303M424400 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | SPRING CONVEYING |
| Парткод: | 303H316360 |
| Деталь: | SHAFT REGISTRATION PULLEY |
| Парткод: | 303LL07130 |
| Деталь: | SPRING REGISTRATION |
| Парткод: | 303LL07170 |
| Деталь: | SPACER CIS |
| Парткод: | 303NW24050 |
| Деталь: | GUIDE REGIST UPPER |
| Парткод: | 303M407260 |
| Деталь: | ARM CIS ROLLER FRONT |
| Парткод: | 303M407270 |
| Деталь: | GUIDE CIS ROLLER |
| Парткод: | 303M407291 |
| Деталь: | LEVER HANDLE |
| Парткод: | 303M407310 |
| Деталь: | PLATE EARTH CIS ROLLER |
| Парткод: | 303M407330 |
| Деталь: | PLATE PF COVER FRONT |
| Парткод: | 303M407340 |
| Деталь: | PLATE PF COVER REAR |
| Парткод: | 303M407350 |
| Деталь: | SHAFT CIS IDLE |
| Парткод: | 303M407360 |
| Деталь: | HOLDER REGIST PULLEY |
| Парткод: | 303M407370 |
| Деталь: | SHEET CIS ROLLER |
| Парткод: | 303M407410 |
| Деталь: | COVER PF FRONT |
| Парткод: | 303M407510 |
| Деталь: | PLATE EARTH CIS REAR |
| Парткод: | 303NW24060 |
| Деталь: | HOLDER GEAR |
| Парткод: | 303M407530 |
| Деталь: | MOUNT CIS SW |
| Парткод: | 303M424130 |
| Деталь: | SHAFT CIS IDLE |
| Парткод: | 303M424240 |
| Деталь: | PLATE EARTH SHD PWB |
| Парткод: | 303M424290 |
| Деталь: | LABEL SIZE INDICATOR |
| Парткод: | 303P234010 |
| Деталь: | WIRE SHD |
| Парткод: | 303M446110 |
| Деталь: | WIRE CISTMG |
| Парткод: | 303M446120 |
| Деталь: | HOUSING CIS |
| Парткод: | 303NW24011 |
| Деталь: | STOPPER CIS GLASS |
| Парткод: | 303NW24030 |
| Деталь: | PLATE EARTH CIS |
| Парткод: | 303NW24040 |
| Деталь: | PIN PF COVER |
| Парткод: | 303LL02190 |
| Деталь: | STRAP PF COVER |
| Парткод: | 303M407380 |
| Деталь: | SHAFT CIS PULLEY |
| Парткод: | 303M424340 |
| Деталь: | HOLDER CIS PULLEY |
| Парткод: | 303M424350 |
| Деталь: | SPRING CIS PULLEY |
| Парткод: | 303M424420 |
| Деталь: | FILM RETARD |
| Парткод: | 302K908610 |
| Деталь: | BASE MPF LOWER |
| Парткод: | 302K908021 |
| Деталь: | ACTUATOR FEED MPF |
| Парткод: | 302K908280 |
| Деталь: | SPRING ACTUATOR BYPASS |
| Парткод: | 302FZ22870 |
| Деталь: | HOLDER RETARD MPF |
| Парткод: | 302K908240 |
| Деталь: | FELT DUPLEX |
| Парткод: | 3H610240 |
| Деталь: | SHAFT RETARD MPF B |
| Парткод: | 302K908501 |
| Деталь: | JOINT RETARD DRIVE |
| Парткод: | 302K906180 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR RETARD MPF Z24L |
| Парткод: | 302K908420 |
| Деталь: | SHAFT RETARD MPF A |
| Парткод: | 302K908491 |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | TORQUE-LIMITER 390 |
| Парткод: | 302K906750 |
| Деталь: | SPRING RETARD MPF |
| Парткод: | 302K908540 |
| Деталь: | COUPLING PRIMARY FEED DRIVE |
| Парткод: | 302K906140 |
| Деталь: | PULLEY FACE UP |
| Парткод: | 302F925160 |
| Деталь: | SPRING HOLDER PULLEY |
| Парткод: | 302K924770 |
| Деталь: | BASE MPF UPPER |
| Парткод: | 302K908012 |
| Деталь: | HOLDER MIDDLE PULLEY |
| Парткод: | 302K908250 |
| Деталь: | SPRING MIDDLE |
| Парткод: | 302LF08010 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | PULLEY MIDDLE A |
| Парткод: | 302H722760 |
| Деталь: | SPRING MIDDLE R |
| Парткод: | 302K908700 |
| Деталь: | GEAR FEED Z26H |
| Парткод: | 302F906030 |
| Деталь: | SHAFT PICKUP MPF |
| Парткод: | 302K908300 |
| Деталь: | GEAR Z30R PICKUP |
| Парткод: | 302K908350 |
| Деталь: | PARTS GEAR Z30R ONE-WAY SP |
| Парткод: | 302K994540 |
| Деталь: | PULLEY,PAPER FEED |
| Парткод: | 2AR07220 |
| Цена: | 1 600 ₽ |
| Деталь: | SHAFT FEED MPF A |
| Парткод: | 302K908471 |
| Деталь: | JOINT DRIVE |
| Парткод: | 302FB06151 |
| Деталь: | SPRING PICKUP MPF |
| Парткод: | 302K908530 |
| Деталь: | HOLDER FEED MPF |
| Парткод: | 302K908230 |
| Деталь: | ACTUATOR PAPER SET |
| Парткод: | 302K908290 |
| Деталь: | SPRING PAPER SET |
| Парткод: | 302K908570 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | MOUNT PI |
| Парткод: | 302K908460 |
| Деталь: | WIRE MPF |
| Парткод: | 302K946370 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SHAFT FEED MPF B |
| Парткод: | 302K908480 |
| Деталь: | GUIDE DU LOWER |
| Парткод: | 302K908320 |
| Деталь: | CASE LIFT MOTOR A |
| Парткод: | 302K908261 |
| Деталь: | PARTS MPT LIFT MOTOR ASSY SP |
| Парткод: | 302LC94200 |
| Деталь: | PLATE DC MOTOR 6 |
| Парткод: | 302K908660 |
| Деталь: | GEAR Z46S-Z18S |
| Парткод: | 302K908370 |
| Деталь: | WORM-WHEEL 36 Z18S |
| Парткод: | 302K908360 |
| Деталь: | GEAR LIFT Z25S |
| Парткод: | 302K908390 |
| Деталь: | GEAR LIFT Z64S |
| Парткод: | 302K908380 |
| Деталь: | LEVER LIFT |
| Парткод: | 302K908310 |
| Деталь: | GEAR RETARD MPF Z17L |
| Парткод: | 302K908410 |
| Деталь: | PIN RETARD MPF |
| Парткод: | 302K908450 |
| Деталь: | GEAR Z27R ONEWAY |
| Парткод: | 303LL31440 |
| Деталь: | COVER CLUTCH |
| Парткод: | 302K908270 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | DAMPER MPF B |
| Парткод: | 302K908630 |
| Деталь: | DAMPER MPF A |
| Парткод: | 302K908620 |
| Деталь: | SPRING DAMPER |
| Парткод: | 302K908640 |
| Деталь: | GUIDE MIDDLE MPF |
| Парткод: | 302K908440 |
| Деталь: | SHEET MPF F |
| Парткод: | 302N408010 |
| Деталь: | SHEET MPF R |
| Парткод: | 302N408020 |
| Деталь: | FILM MIDDLE GUIDE |
| Парткод: | 302K908590 |
| Деталь: | FILM DU GUIDE B |
| Парткод: | 302K908692 |
| Деталь: | COVER DU |
| Парткод: | 302K929071 |
| Деталь: | GUIDE COVER DU |
| Парткод: | 302K929080 |
| Деталь: | LID FILTER DU |
| Парткод: | 302K929380 |
| Деталь: | PARTS MPT ASSY SP |
| Парткод: | 302K994012 |
| Деталь: | PARTS COVER GUIDE DU L ASSY SP |
| Парткод: | 302LC94470 |
| Деталь: | Узел первичной вертикальной подачи бумаги, в сборе |
| Парткод: | 302N494021 |
| Цена: | 14 700 ₽ |
| Деталь: | Средний узел подачи бумаги дополнительного лотка, в сборе |
| Парткод: | 303NF94011 |
| Деталь: | MC-6705 |
| Парткод: | 302LF93021 |
| Деталь: | DV-6706 |
| Парткод: | 302N793060 |
| Деталь: | SHUTTER PIPE UP |
| Парткод: | 302H703100 |
| Деталь: | SEAL PIPE DLP UP |
| Парткод: | 302H703130 |
| Деталь: | SPRING PIPE UP |
| Парткод: | 302H703240 |
| Деталь: | SEAL CONT SHUTTER |
| Парткод: | 302H703570 |
| Деталь: | SPRING SHUTTER |
| Парткод: | 302K914370 |
| Деталь: | SHUTTER HOPPER UP |
| Парткод: | 302K915240 |
| Деталь: | SEAL SHUTTER |
| Парткод: | 302K915320 |
| Деталь: | PIPE DLP UP |
| Парткод: | 302H703542 |
| Деталь: | BASE GUIDE CONTAINER |
| Парткод: | 302LF03710 |
| Деталь: | RAIL CONTAINER L |
| Парткод: | 302LF03730 |
| Деталь: | SHAFT CAM |
| Парткод: | 302LF02220 |
| Деталь: | MOUNT CAM |
| Парткод: | 302LF02240 |
| Деталь: | CAM DLP PRESS |
| Парткод: | 302LF02230 |
| Деталь: | SPRING CAM |
| Парткод: | 302LF02250 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | BUSH 8 |
| Парткод: | 302H024830 |
| Деталь: | PLATE PRESS LEVER |
| Парткод: | 302LF02210 |
| Деталь: | LEVER DLP RAIL |
| Парткод: | 302LF02260 |
| Деталь: | SPRING LEVER DLP |
| Парткод: | 302LF02180 |
| Деталь: | ARM RAIL R |
| Парткод: | 302N702121 |
| Деталь: | SPRING HV |
| Парткод: | 302K939360 |
| Деталь: | SPRING HV |
| Парткод: | 302K939200 |
| Деталь: | TERMINAL MAG |
| Парткод: | 302LF02150 |
| Деталь: | TERMINAL SLEEVE |
| Парткод: | 302LF02160 |
| Деталь: | SHAFT DLP DRIVE |
| Парткод: | 302K931180 |
| Деталь: | SPRING COUPLING DLP |
| Парткод: | 302BG22531 |
| Деталь: | COUPLING DLP DRIVE |
| Парткод: | 302FZ31250 |
| Деталь: | COLLAR DLP COUPLING |
| Парткод: | 302FZ31280 |
| Деталь: | PIN CASSETTE RAIL |
| Парткод: | 2FB06710 |
| Деталь: | GEAR Z74R |
| Парткод: | 302K931190 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RETAINER DLP DRIVE |
| Парткод: | 302LF02191 |
| Деталь: | PLATE EARTH DRIVE |
| Парткод: | 302LF02390 |
| Деталь: | SEAL TONER DUCT |
| Парткод: | 302N702050 |
| Деталь: | COVER TONER DUCT Z |
| Парткод: | 302N702270 |
| Деталь: | DUCT COOLING |
| Парткод: | 302LF02420 |
| Деталь: | SEAL COOLING DUCT |
| Парткод: | 302LF02430 |
| Деталь: | RAIL DLP |
| Парткод: | 302LF02101 |
| Деталь: | ARM RAIL F |
| Парткод: | 302LF02110 |
| Деталь: | WIRE DEVELOPER JOINT |
| Парткод: | 302LF46640 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | PULLEY,DRUM SEPARATION |
| Парткод: | 2A118370 |
| Цена: | 90 ₽ |
| Деталь: | COVER DRUM |
| Парткод: | 302LF02282 |
| Деталь: | STAY DRUM COVER |
| Парткод: | 302LF02351 |
| Деталь: | ARM COVER DRUM FRONT |
| Парткод: | 302LF02292 |
| Деталь: | MOUNT COVER DRUM FRONT |
| Парткод: | 302LF02370 |
| Деталь: | ARM COVER DRUM REAR |
| Парткод: | 302LF02301 |
| Деталь: | MOUNT COVER DRUM REAR |
| Парткод: | 302LF02360 |
| Деталь: | SPRING-TORSION ARM A FRONT |
| Парткод: | 302LF02311 |
| Деталь: | SPRING-TORSION ARM B FRONT |
| Парткод: | 302LF02330 |
| Деталь: | SPRING-TORSION ARM A REAR |
| Парткод: | 302LF02321 |
| Деталь: | SPRING-TORSION ARM B REAR |
| Парткод: | 302LF02340 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS,FAN IMAGE SP |
| Парткод: | 302FZ94660 |
| Деталь: | DUCT DLP A |
| Парткод: | 302N702240 |
| Деталь: | DUCT DLP B |
| Парткод: | 302N702250 |
| Деталь: | MOUNT FAN DLP |
| Парткод: | 302N702260 |
| Деталь: | TUBE COOLING A |
| Парткод: | 302N702280 |
| Деталь: | TUBE COOLING B |
| Парткод: | 302N702290 |
| Деталь: | SPRING COVER TONER DUCT Z |
| Парткод: | 302N702300 |
| Деталь: | SEAL DUCT |
| Парткод: | 302N702310 |
| Деталь: | SHEET WIRE |
| Парткод: | 302N702320 |
| Деталь: | WIRE DLP ASSIST FAN |
| Парткод: | 302N746100 |
| Деталь: | PIN COVER DRUM |
| Парткод: | 302N902030 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SEAL TN FEED E |
| Парткод: | 302HN21920 |
| Деталь: | SEAL RID |
| Парткод: | 302HN21860 |
| Деталь: | SEAL COVER LEFT B |
| Парткод: | 302HG14780 |
| Деталь: | DK-6706 |
| Парткод: | 302N793050 |
| Деталь: | HINGE OPERATION ARM |
| Парткод: | 302K905500 |
| Деталь: | LID OPERATION HINGE B |
| Парткод: | 302K905150 |
| Деталь: | LID OPERATION HINGE A |
| Парткод: | 302K905140 |
| Деталь: | COVER OPERATION ARM A |
| Парткод: | 302N205090 |
| Деталь: | COVER OPERATION ARM B |
| Парткод: | 302N205100 |
| Деталь: | COVER OPERATION HINGE A |
| Парткод: | 302N205110 |
| Деталь: | COVER OPERATION HINGE B |
| Парткод: | 302N205120 |
| Деталь: | COVER OPERATION MOUNT A |
| Парткод: | 302K904400 |
| Деталь: | COVER OPERATION MOUNT B |
| Парткод: | 302K904410 |
| Деталь: | COVER HINGE FULCRUM A |
| Парткод: | 302N205130 |
| Деталь: | COVER HINGE FULCRUM B |
| Парткод: | 302N205140 |
| Деталь: | GUIDE WIRE OPERATION A |
| Парткод: | 302K905540 |
| Деталь: | GUIDE WIRE OPERATION B |
| Парткод: | 302K905550 |
| Деталь: | MOUNT OPERATION ARM |
| Парткод: | 302K905591 |
| Деталь: | GUIDE OPERATION MOUNT |
| Парткод: | 302K905641 |
| Деталь: | GUIDE WIRE FRONT PWB |
| Парткод: | 302LF39050 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | SHEET WIRE |
| Парткод: | 302F902450 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | SHEET LEFT GUIDE A |
| Парткод: | 303JX07350 |
| Деталь: | SEAL CASE DLP |
| Парткод: | 302K914A50 |
| Деталь: | SEAL OPERATION ARM |
| Парткод: | 302N205180 |
| Деталь: | HOLDER FEED DRIVE |
| Парткод: | 302K931411 |
| Деталь: | SHAFT MID DRIVE |
| Парткод: | 302K931441 |
| Деталь: | COUPLING DRIVE |
| Парткод: | 302K931530 |
| Деталь: | SPRING DRUM JOINT |
| Парткод: | 302H712650 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SHAFT FEED DRIVE |
| Парткод: | 302K931431 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | SHAFT ASSIST DRIVE |
| Парткод: | 302K931480 |
| Деталь: | GEAR Z28L |
| Парткод: | 302K931490 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 302K931450 |
| Деталь: | GEAR Z28R |
| Парткод: | 302K931500 |
| Деталь: | GEAR Z27L |
| Парткод: | 302K931550 |
| Деталь: | GEAR Z27L MAIN |
| Парткод: | 302JZ31170 |
| Деталь: | GEAR Z35R |
| Парткод: | 302K931510 |
| Деталь: | GEAR Z40L-Z34L |
| Парткод: | 302K931520 |
| Деталь: | GEAR Z61R-Z34R |
| Парткод: | 302K931470 |
| Деталь: | WIRE ASSIST CLUTCH |
| Парткод: | 302K946690 |
| Деталь: | PLATE FEED DRIVE |
| Парткод: | 302K931420 |
| Деталь: | PARTS MOTOR-BL W30 SP |
| Парткод: | 302K994331 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 302K931540 |
| Деталь: | PARTS PWB FEED 2 ASSY SP |
| Парткод: | 302N494170 |
| Деталь: | WIRE FEED MOTOR |
| Парткод: | 302K946441 |
| Деталь: | WIRE FEED CLUTCH |
| Парткод: | 302K946AB0 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | HOLDER CONT DRIVE K |
| Парткод: | 302K931710 |
| Деталь: | PARTS LSU RETAINER MOTOR ASSY SP |
| Парткод: | 302K994D00 |
| Деталь: | SEAL MOTOR DC |
| Парткод: | 302LC31511 |
| Деталь: | PLATE DC MOTOR 10 |
| Парткод: | 302K902610 |
| Деталь: | WORM WHEEL Z56L-Z20S |
| Парткод: | 302K931760 |
| Деталь: | SHAFT CONT DRIVE |
| Парткод: | 302K931780 |
| Деталь: | GEAR Z34S JOINT |
| Парткод: | 302K931830 |
| Деталь: | PLATE CONT DRIVE |
| Парткод: | 302K931720 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302K394070 |
| Деталь: | SPRING PADDLE CONT D |
| Парткод: | 302H731650 |
| Деталь: | COUPLING CONT D |
| Парткод: | 302H731640 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | WIRE CONTAINER MOTOR |
| Парткод: | 302LF46350 |
| Деталь: | WIRE FEED POWER |
| Парткод: | 302K946930 |
| Деталь: | GEAR Z35S |
| Парткод: | 302K903130 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | PARTS FEED DRIVE H UNIT SP |
| Парткод: | 302N493030 |
| Деталь: | PARTS CONT DRIVE UNIT K SP |
| Парткод: | 302LF94080 |
| Деталь: | CURSOR REAR |
| Парткод: | 303M406021 |
| Деталь: | RACK TABLE |
| Парткод: | 303M406031 |
| Деталь: | CUSHION CURSOR |
| Парткод: | 3HL06090 |
| Деталь: | TERMINAL PAPER SIZE |
| Парткод: | 3HL06110 |
| Деталь: | LABEL ORIGINAL MAX |
| Парткод: | 303P634010 |
| Деталь: | CURSOR FRONT |
| Парткод: | 303M406011 |
| Деталь: | PINION GEAR |
| Парткод: | 303JX06070 |
| Деталь: | COVER CURSOR |
| Парткод: | 303M406040 |
| Деталь: | SENSOR EARTH |
| Парткод: | 303JX06090 |
| Деталь: | TABLE LIFT |
| Парткод: | 303M406090 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 303NW94060 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | PARTS PWB SIZE DETECTION ASSY SP |
| Парткод: | 303M894270 |
| Деталь: | PAD,LIFT |
| Парткод: | 3A707290 |
| Деталь: | BASE TABLE |
| Парткод: | 303M406100 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | WIRE TABLE UNIT |
| Парткод: | 303M446040 |
| Деталь: | GEAR LIFT Z30 |
| Парткод: | 303M406070 |
| Деталь: | COVER TABLE |
| Парткод: | 303M406110 |
| Деталь: | SUB TABLE |
| Парткод: | 303M406121 |
| Деталь: | MOUNT ORIGINAL SENSOR |
| Парткод: | 303LL06090 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 303NW94050 |
| Деталь: | LABEL FACE UP EN |
| Парткод: | 303M434100 |
| Деталь: | LABEL CAUTION IN |
| Парткод: | 303M434020 |
| Деталь: | LABEL CAUTION ME |
| Парткод: | 303M434030 |
| Деталь: | FILM WIRE OPE |
| Парткод: | 302H702540 |
| Деталь: | SPRING DRUM JOINT |
| Парткод: | 302H712650 |
| Деталь: | PIN TABLE |
| Парткод: | 303M402210 |
| Деталь: | LEVER LIFT |
| Парткод: | 303M406050 |
| Деталь: | SHAFT LIFT |
| Парткод: | 303M406060 |
| Деталь: | BUSH TABLE |
| Парткод: | 303M406080 |
| Деталь: | COVER TABLE REAR |
| Парткод: | 303M406130 |
| Деталь: | LABEL FACE UP SET |
| Парткод: | 303M434130 |
| Деталь: | LABEL CAUTION SET IN |
| Парткод: | 303M434110 |
| Деталь: | LABEL CAUTION SET ME |
| Парткод: | 303M434120 |
| Деталь: | SEAL CONVEYING DU |
| Парткод: | 302N724010 |
| Деталь: | PLATE CONTACT CLEANING |
| Парткод: | 302LF24081 |
| Деталь: | SPRING CONTACT TRANSFER |
| Парткод: | 302LF24040 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+020H01 |
| Деталь: | PLATE CONTACT HV |
| Парткод: | 302K924290 |
| Деталь: | CAP PRESS TRANSFER |
| Парткод: | 302LF24010 |
| Деталь: | SPRING-COMPRESSION BELT ASSY B |
| Парткод: | 302LF24030 |
| Деталь: | SPRING-COMPRESSION BELT ASSY A |
| Парткод: | 302LF24020 |
| Деталь: | PLATE EARTH REGIST |
| Парткод: | 302K924250 |
| Деталь: | SHEET WIRE SENSOR |
| Парткод: | 302LF24160 |
| Деталь: | WIRE DU LOW |
| Парткод: | 302LF46311 |
| Деталь: | RETAINER LOOP SENSOR |
| Парткод: | 302K924100 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302LC94410 |
| Деталь: | BUSH REGIST |
| Парткод: | 302K924901 |
| Деталь: | SPRING-COMPRESSION REGIST F |
| Парткод: | 302K924040 |
| Деталь: | SPRING-COMPRESSION REGIST R |
| Парткод: | 302K924050 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | BEARING MR106ZZ |
| Парткод: | 7BE006103431H01 |
| Деталь: | GEAR Z22R |
| Парткод: | 302K924060 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SPRING EARTH CONVEYING |
| Парткод: | 302LF22600 |
| Деталь: | UNDER CLEANER REGIST |
| Парткод: | 2BL07950 |
| Цена: | 1 500 ₽ |
| Деталь: | ROLLER REGIST R |
| Парткод: | 302LF24150 |
| Деталь: | SHEET REGIST R |
| Парткод: | 302LF24190 |
| Деталь: | SPRING HOLDER PULLEY |
| Парткод: | 302K924770 |
| Деталь: | PULLEY MPT BYPASS |
| Парткод: | 302FZ07020 |
| Деталь: | PLATE EARTH RELEASE |
| Парткод: | 302K924810 |
| Деталь: | PLATE CONTACT TRANSFER |
| Парткод: | 302LF24070 |
| Деталь: | MOUNT ID SENSOR |
| Парткод: | 302LF22390 |
| Деталь: | PARTS ID SENSOR ASSY SP |
| Парткод: | 302K994160 |
| Деталь: | MOUNT SENSOR UNIT |
| Парткод: | 302LF22540 |
| Деталь: | SHUTTER ID SENSOR |
| Парткод: | 302LF22550 |
| Деталь: | FELT CLEANER ID |
| Парткод: | 302HN02970 |
| Деталь: | ARM SOLENOID |
| Парткод: | 302LF22530 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SPRING EXTENSION SHUTTER |
| Парткод: | 302LF22610 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | PARTS SOLENOID ID SENSOR SP |
| Парткод: | 302K994390 |
| Деталь: | BUSH DU EW |
| Парткод: | 302K924830 |
| Деталь: | PARTS MOTOR PM REGIST SP |
| Парткод: | 302K994980 |
| Деталь: | HOLDER CONTACT BELT |
| Парткод: | 302LF24091 |
| Деталь: | SPRING CONTACT BELT UNIT |
| Парткод: | 302LF24060 |
| Деталь: | PARTS ROLLER DU MID SP |
| Парткод: | 302K994480 |
| Деталь: | PLATE EARTH DU MIDDLE |
| Парткод: | 302K929660 |
| Деталь: | BELT S2M A145 |
| Парткод: | 302K929310 |
| Деталь: | MOUNT MOTOR DU MIDDLE |
| Парткод: | 302K929720 |
| Деталь: | LOCK COVER R /40283V0068 A4 |
| Парткод: | 5MVX421DN003 |
| Деталь: | POLYSLIDER CUT WASHER 4 |
| Парткод: | 302FZ21720 |
| Деталь: | SPRING-COMPRESSION COVER DU |
| Парткод: | 302K929680 |
| Деталь: | SPRING ACT DU |
| Парткод: | 302H729120 |
| Деталь: | ACTUATOR DU |
| Парткод: | 302K929330 |
| Деталь: | MOUNT PI |
| Парткод: | 302K924841 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | WIRE DU SENSOR |
| Парткод: | 302LF46461 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | FRAME DU |
| Парткод: | 302K924410 |
| Деталь: | SPRING DU |
| Парткод: | 302F925780 |
| Деталь: | PULLEY MIDDLE A |
| Парткод: | 302H722760 |
| Деталь: | PARTS ROLLER DU LOW SP |
| Парткод: | 302K994470 |
| Деталь: | PLATE EARTH DU2 |
| Парткод: | 302K924920 |
| Деталь: | PULLEY 26 DU |
| Парткод: | 302H029110 |
| Деталь: | CUT-WASHER 6 |
| Парткод: | 302K921420 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING DU |
| Парткод: | 302K929770 |
| Деталь: | BASE CONVEYING |
| Парткод: | 302K924011 |
| Деталь: | GEAR Z43R |
| Парткод: | 302K929740 |
| Деталь: | PARTS CONVEYING H UNIT SP |
| Парткод: | 302N794080 |
| Деталь: | PARTS ID SENSOR ASSY SP |
| Парткод: | 302LF94070 |
Коды ошибок
0030
0060
0070
0100
0120
0150
0160
0170
0180
0350
0620
0630
0640
0650
0660
0670
0800
0830
0840
0870
0920
0980
1000
1010
1020
1050
1060
1070
1100
1110
1140
1250
1350
1400
1410
1450
1710
1800
1810
1820
1900
1910
1920
2101
2201
2211
2300
2500
2550
2600
2610
2640
2650
2660
2670
3100
3210
3220
3300
3310
3500
3600
3700
3800
3900
4001
4011
4101
4201
5101
6000
6020
6030
6040
6050
6100
6120
6130
6150
6200
6220
6230
6250
6320
6330
6520
6530
6600
6610
6620
6710
6720
6730
6740
6750
6760
6770
6910
6920
6930
6940
6950
6960
6980
6990
7001
7101
7200
7210
7221
7231
7241
7251
7301
7401
7411
7460
7470
7601
7602
7800
7901
7911
7941
8000
8010
8020
8030
8090
8100
8110
8120
8130
8140
8150
8160
8170
8180
8190
8200
8210
8230
8240
8260
8300
8310
8320
8330
8340
8350
8360
8410
8420
8430
8500
8510
8520
8800
8900
8930
9000
9010
9040
9050
9060
9070
9080
9100
9110
9120
9130
9140
9150
9160
9170
9500
9510
9520
9940
9950
F000
F010
F040
F041
F050
F051
F12X
F13X
F14X
F15X
F17X
F18X
F1CX
F1DX
F21X, F22X, F23X
F24X
F25X
F26X ... F2AX
F278
F33X
F34X
F35X
F36X
F37X
F38X
F3AX ... F45X
F46X
F47X ... F49X
F4AX, F4CX
F4DX, F4EX
F4FX
F50X
F51X ... F57X
F58X ... F5EX
F5FX
F60X
F61X
F62X
F63X
F64X ... F67X
F68X
F69X ... F6CX
F6DX ... F75X
Описание
| Error code: | 0030 |
| Description: | FAX control PWB system error Processing with the fax software was disabled due to a software problem. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Reinstall the fax software. 3. Replace the FAX control PWB. |
| Error code: | 0060 |
| Display: | FUSER MOTOR |
| Description: | Engine PWB mismatch Unmatching engine and engine sub boards. Defective engine subboard |
| Causes: | Defective engine sub PWB. |
| Remedy: | Engine PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Replace the engine PWB. |
| Error code: | 0070 |
| Description: | FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX control PWB (The FAX PWB installed will not be the one designed for the machine.) 1. Install the FAX system designed for the model. 2. Reinstall the fax software. |
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0180 |
| Description: | Even though the machine carries out the regular movement, the output of Maintenance Liquid Pump Sensor does not reach the expected value. |
| Causes: | Maintenance Liquid Pump Motor has a problem. Maintenance Liquid Pump Sensor has a problem. Maintenance Liquid Pump Magnet has dropped out. Wiring or Flexible Cable has short circuitted |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Maintenance Liquid Pump Motor replacement Maintenance Liquid Pump Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0350 |
| Description: | Panel PWB communication error (electronic volume I2C communication error) NACK is received during I2C communication -> retried 5 times -> rebooting command sent -> retried 5 times If NACK is still received. |
| Causes: | Operation PWB. Main PWB |
| Remedy: | Operation PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Operation PWB (YC10) and Main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. Main PWB Replace the main PWB. |
| Error code: | 0620 |
| Description: | FAX image DIMM error 1. The Fax image DIMM has not been installed. 2. Fax image DIMM access error. |
| Causes: | DIMM installed incorrectly. Defective main PWB. |
| Remedy: | FAX image DIMM 1. Install the FAX image DIMM supplied in the FAX system onto the main PWB. 2. Firmly install the FAX image DIMM again onto the main board. 3. Check the FAX image DIMM terminals and remove any foreign objects that may be adhered to it. 4. Replace with a new FAX image DIMM. Main PWB. Replace the main PWB. |
| Error code: | 0630 |
| Description: | DMA error DMA transmission of image data does not complete within the specified period of time. |
| Causes: | Poor contact in the connector terminals. Defective main PWB. |
| Remedy: | DP CIS 1. Reconnect the CIS signal line. 2. Confirm that the CIS connector terminals are firmly connected. Insert the connector all the way in. 3. If the wiring is disconnected, shorted or grounded, replace the wiring. DP main PWB Main PWB 1. Confirm that the wiring connector is firmly connectHDD number difference 1. Confirm whether the HDD number is correct in U024_Composition and change it if different. HDD 1piece: Single HDD 2pieces: Multied and, if necessary, connect the connector all the way in. 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Wiring that connects the CIS and the DP controller PWB. Wiring that connects the DP main PWB and the main PWB. 3. Replace the DP main PWB. 4. Replace the main PWB. |
| Error code: | 0640 |
| Description: | Hard disk error The hard disk cannot be accessed. |
| Causes: | Defective hard disk. Defective main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Lack of HDD capacity 1. Confirm the total capacity of the HDD if it is more than 320GB. Change the HDD or add it in case of lacking in capacity. Main PWB Replace the main PWB. |
| Error code: | 0650 |
| Display: | Scanner home failure CODE (0650) Turn power off, on |
| Description: | Scanner Home Failure • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the Polygon Motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the Polygon Motor remains energized. |
| Causes: | • Engine Control Board, PL13.0.20 • Image Processor Board, PL2.0.4 |
| Remedy: | 1 Check connector P/J2 on the Image Processor Board. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Replace the Scanner. Does the problem persist? Go to step 3. Complete. 3 Replace the Engine Control Board. Does the problem persist? Go to step 4. Complete. 4 Replace the Power Supply. Complete. |
| Error code: | 0660 |
| Description: | Hard disk encryption key error |
| Causes: | EEPROM. HDD. Main PWB |
| Remedy: | EEPROM 1. Execute U004 if this occurs after the EEPROM has been changed. HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
| Error code: | 0670 |
| Description: | Hard disk overwriting erasure error |
| Causes: | HDD. Main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0830 |
| Description: | FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX software 1. Reinstall the fax software. FAX control PWB 1. Execute initializing by U600.(Refer to the FAX service manual) 2. Replace the FAX control PWB. |
| Error code: | 0840 |
| Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
| Causes: | The battery is disconnected from the main PWB Defective main PWB. |
| Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
| Error code: | 0870 |
| Description: | PCFAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. |
| Causes: | Improper installation FAX control PWB. Defective FAX control PWB or main PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Replace the FAX control PWB. HDD Execute U024 to initialize the HDD. Main PWB Replace the main PWB. |
| Error code: | 0920 |
| Description: | Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Execute initializing by U600 (Refer to the FAX service manual). 2. Replace the FAX control PWB. |
| Error code: | 0980 |
| Description: | 24 V power down detect If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second. |
| Causes: | Defective power source PWB. |
| Remedy: | Power source PWB 1. Check the +24V output is given at YC12- 1 to 3 of the power circuit PWB. 2. Replace the power source PWB |
| Error code: | 1000 |
| Description: | MP lift motor error If the MP lift sensor 1 (upper limit detect) or 2 (bottom detect) is not detectable to be turned on while the MP lift motor is ascending or descending. |
| Causes: | Defective MP plate elevation mechanism. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective MP lift motor. Defective engine PWB. |
| Remedy: | Manual feed lift base elevating mechanism 1. Check that the paper lift base of the manual feed tray can smoothly ascend and descent, if not, repair or replace. 2. Check that the lift lever is located so that it can ascend or descend by the lift motor cam and that it not damaged and, if necessary, re-install or replace the manual feed table. MP lift motor 1. Check that the paper elevator has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MP lift motor and Relay PWB (YC3) Relay PWB (YC12) and Feed PWB1 (YC17) Feed PWB1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the MP lift motor. MP lift sensor1 MP lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MP lift sensor1,2 and Relay PWB (YC3) Relay PWB (YC12) and Feed PWB1(YC17) Feed PWB1 (YC1) and Engine PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MP lift sensor1 or MP lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1050 |
| Display: | Blue platen switch is dirty. Please clean the switch. |
| Description: | SM lift motor error (side multi tray) After cassette 5 is inserted, SM lift sensor does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor Defective SM lift motor. Defective SM main PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. SM Lift motor 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM Lift motor and SM main PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SM Lift motor. SM Lift sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM Lift sensor and SM main PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the SM Lift sensor. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1060 |
| Description: | PF lift motor 1 error (side paper feeder) After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. *:The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 1 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. PF Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor1 and PF main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor 1. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1070 |
| Description: | PF lift motor 2 error (side paper feeder) After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. *:The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 2 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF Lift motor2. PF Lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor 2 and PF main PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. PFReplace the lift sensor2. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1100 |
| Display: | Prepare for maint cart replacement. |
| Description: | Paper Jam There is paper jammed in the All-In-One. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Clear the paper jam, and resend the print job. |
| Error code: | 1110 |
| Description: | PF lift motor 2 error (large capacity feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 2 is turned on is excluded from detection. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 2 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF Lift motor2. PF Lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor 2 and PF main PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the PF Lift sensor 2. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1140 |
| Description: | SD lift motor error (side deck) After cassette 5 is inserted, SD lift sensor does not turn on within 30 s. The lock signal of the motor is detected continuously for 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective SD lift motor. Defective SD main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. SD Lift motor 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SD Lift motor and SD main PWB (YC8) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SD Lift motor. SD Lift sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SD Lift sensor and SD main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the SD Lift sensor. SD main PWB Replace the SD main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1250 |
| Description: | SM multi feed sensor communication error (side multi tray) A communication error is detected 3 times in succession. |
| Causes: | Improper installation side multi tray. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. |
| Remedy: | Side multi tray Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1350 |
| Description: | SM multi feed sensor error (side multi tray) The SM multi feed sensor has detected multi feeding 5 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective SM multi feed sensor. Defective SM main PWB. |
| Remedy: | SM multi feed sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM multi feed sensor and SM main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the SM multi feed sensor. SM main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1400 |
| Display: | Condensation Leave switched ON. Fully open the Front Cover. Wait 30 minutes, switch OFF and close cover, then switch ON. |
| Description: | Rotary guide motor error The guide sensor is not detected to be on at the home position detection with the rotary guide for three times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective BR guide motor. Defective BR main PWB. Defective engine PWB. |
| Remedy: | Rotary guide motor 1. Check the rotary guide and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Rotary guide motor and BR PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the rotary guide motor. BR PWB Replace the BR PWB. |
| Error code: | 1410 |
| Description: | Rotary de-curler error If the de-curler won’t turn On/ Off despite it has been activated for 400 steps during waiting for the de-curler sensor to be On/Off three times in a row (3 times in succession). |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective BR decurler motor. Defective BR main PWB. Defective engine PWB. |
| Remedy: | Rotary de-curler motor 1. Check the rotary de-curler and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Rotary de-curler motor and BR PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the rotary de-curler motor. BR PWB Replace the BR PWB. |
| Error code: | 1450 |
| Description: | SM multi feed sensor backup error (side multi tray) When writing the data, read and write data does not match 3 times in succession. Deleting a block has failed three times in a row. Writing won’t complete in 200 ms after writing has commenced. |
| Causes: | Defective connector cable or poor contact in the connector. Defective SM multi feed sensor. Defective SM main PWB. |
| Remedy: | SM multi feed sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM multi feed sensor and SM main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM multi feed sensor. SM main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1710 |
| Description: | Side multi tray incompatible detection error The side multi tray has been installed with a device to which it is incompatible. |
| Causes: | The side multi tray is installed with a device to which it is incompatible. |
| Remedy: | The side multi tray is installed with a device to which it is incompatible. Install the side multi-tray with the target model. |
| Error code: | 1800 |
| Description: | Paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| Remedy: | Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1810 |
| Description: | Side multi tray communication error A communication error from side multi tray is detected 10 times in succession. |
| Causes: | Improper installation side multi tray. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. |
| Remedy: | Side multi tray Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). Engine PWB Check the engine software and upgrade to the latest, if necessary. Replace the engine PWB. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1820 |
| Description: | Side paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation side paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective SM main PWB. Defective PF main PWB. |
| Remedy: | Side paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. SM main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM main PWB (YC1) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the SM main PWB (Refer to the service manual for the paper feeder). PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and SM main PWB (YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1910 |
| Description: | Side multi tray EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective SM main PWB. Device damage of EEPROM. |
| Remedy: | SM main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1920 |
| Description: | Side paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2101 |
| Description: | Developer motor error After developer motor is driven, the ready signal does not turn to L within 2 s. After developer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor. Defective engine PWB. |
| Remedy: | Developer unit 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor 1. To check the motor operation, execute DLP(K) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor and Feed PWB 1 (YC8) Feed PWB 1 (YC2) and Engine PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor. Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2201 |
| Description: | drum motor steady-state error After drum motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor. Defective engine PWB. |
| Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. Drum motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2211 |
| Description: | Drum motor startup error Drum motor is not stabilized within 2 s since the motor is activated. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor K. Defective engine PWB. |
| Remedy: | Drum unit 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the drum or the drum screw can rotate. 3. If it won’t rotate, replace the drum unit. Drum motor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2300 |
| Description: | Fuser motor error After fuser motor is driven, the ready signal does not turn to L within 2 s. After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser motor. Defective engine PWB. |
| Remedy: | Fuser motor 1. To check the motor operation, execute U030 Fuser (Fuser motor). 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser motor and Feed PWB 1(YC18) Feed PWB 1(YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the fuser motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Feed PWB 1 Replace the Feed PWB 1. Fuser unit Replace the fuser unit. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2550 |
| Description: | Transfer motor error After Transfer motor is driven, the ready signal does not turn to L within 2 s. After Transfer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser motor. Defective engine PWB. |
| Remedy: | Transfer motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Transfer motor and Relay PWB(YC6) Relay PWB(YC5) and Feed PWB 1 (YC13) Feed PWB 1 (YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Transfer motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2610 |
| Description: | PF paper feed motor error (paper feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 2PF - Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2640 |
| Description: | SD paper feed motor error (side deck) After SD paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective SD paper feed motor. Defective SD main PWB. |
| Remedy: | SD paper feed motor 1. To check the feed unit operation, execute U247 Side deck- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SD paper feed motor and SD main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SD paper feed motor. SD main PWB Replace the SD main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2650 |
| Description: | SM paper feed motor error (side multi tray) After SM paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective SM paper feed motor. Defective SM main PWB. |
| Remedy: | SM paper feed motor 1. To check the feed unit operation, execute U247 SMT- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SM paper feed motor and SM main PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SM paper feed motor. SM main PWB Replace the SM main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2660 |
| Description: | PF paper feed motor error (side large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 Side LCF - Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2670 |
| Description: | PF paper feed motor error (side paper feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. Execute Side 2PF - Motor ON of U247 feed unit operation check. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 3100 |
| Description: | Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor. |
| Causes: | Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective ISC PWB. Defective main PWB. |
| Remedy: | The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary. Scanner motor 1. To check the scanner motor, execute U073. 2. Move the scanner by the hand to check whether it is unusually difficult to move. 3. Check that the optical wire rope is not disengaged and engage the wire. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the scanner motor. Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and ISC PWB (YC8) 3. Replace the home position sensor. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3210 |
| Description: | CIS lamp error When input value at the time of CIS illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Execute CCD of U061 lamp check. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. DP relay PWB Replace the DP relay PWB. |
| Error code: | 3220 |
| Description: | CCD lamp activation error The threshold is calculated for colors at initialization and the pixel which does not exceed that value is greater than 1000. |
| Causes: | CIS. ISC PWB. Main PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3300 |
| Description: | Optical system (AGC) error One of the gains is FF or 00 during the CCD lamp AGC is being processed. |
| Causes: | Defective connector cable or poor contact in the connector. Defective exposure lamp Defective CCD PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | LED lamp PWB 1. To check the lamp, execute U061 CCD. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. CCD PWB Replace the ISU and execute U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3310 |
| Description: | CIS AGC error After AGC, correct input is not obtained at CIS. |
| Causes: | Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. To check the lamp, execute U061 CCD. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. |
| Error code: | 3500 |
| Description: | Communication error between scanner and ASIC An error code is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective ISC PWB. Defective main PWB. |
| Remedy: | ISC PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ISC PWB (YC3) and Main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3600 |
| Description: | Scanner sequence error |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Execute U021 memory initializing. 2. Replace the ISC PWB and execute U411. |
| Error code: | 3700 |
| Description: | Scanner device error |
| Causes: | CCD connector inserted incorrectly. |
| Remedy: | CCD (ISU) Since the ISU is mounted with a CCD of different type, install the ISU that matches with the model. |
| Error code: | 3800 |
| Description: | AFE error When writing the data, read and write data does not match 3 times in succession. No response is received in 100 ms from AEF. |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. CCD PWB (YC2) and ISC PWB (YC9) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the ISC PWB and execute U411. CCD PWB Replace the ISU and execute U411. |
| Error code: | 3900 |
| Description: | Backup memory read/write error (ISC PWB) Read and write data does not match. |
| Causes: | Defective backup memory or PWB. |
| Remedy: | Backup memory (ISC PWB) 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Replace the ISC PWB and execute U411. |
| Error code: | 4001 |
| Display: | ERROR E146-4001 Call for service. |
| Description: | Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4011 |
| Description: | Polygon motor steady-state error After Polygon motor is stabilized, the ready signal is at the H level for 15 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4101 |
| Description: | BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4201 |
| Display: | Replace Drum:BK |
| Description: | BD steady-state error K The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, shorted or grounded, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 5101 |
| Description: | Main high-voltage error K Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board). |
| Causes: | Defective connector cable or poor contact in the connector. Defective high voltage PWB Defective engine PWB. |
| Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. 3. Check that the discharger lamp is properly connected. Charger roller unit 1. Check that the high-voltage contacts are not distorted or adhered with foreign objects. 2. Reinstall the chrager roller unit.Or, replace the charger roller unit. High voltage PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. High voltage PWB (YC2) and Engine PWB (YC16) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the High voltage PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6040 |
| Description: | Fuser heater error Input from fuser center thermistor 1 is abnormal value continuously for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Center thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6050 |
| Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
| Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6100 |
| Description: | Broken fuser heater wire Fuser thermistor 5 won’t reach the reference temperature in 480 s after shifting to low power mode. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6120 |
| Description: | Abnormally high fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature higher than 190°C/ 374°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 5. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6130 |
| Description: | Broken fuser press thermistor 5 wire The input from the fuser press thermistor 5 has been less than 30°C/ 86°F (A/D: greater thann992) for 60 seconds continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) Fuser IH PWB(YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6150 |
| Description: | Abnormally low fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature lower than 30°C/ 86°F for 1 s after warming up. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 5. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6200 |
| Display: | No Drum Unit Install the Drum Unit. |
| Description: | Broken fuser edge heater wire Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser center thermistor 1 1. Replace the Fuser unit. |
| Error code: | 6220 |
| Description: | Abnormally high fuser edge thermistor temperature Fuser thermistor 2 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 2. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6230 |
| Description: | Broken fuser edge thermistor wire The Input signal from the fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser thermistor 1 is higher than 100°C/212°F. Fuser thermistor 2 detects a lower then 50°C/122°F for 15s during warming up. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 2 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6250 |
| Description: | Abnormally low fuser edge thermistor temperature Fuser thermistor 2 detects a temperature lower than 100°C/212°F for 1 s during ready or print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 2. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Fuser unit and Engine PWB (YC26) If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6320 |
| Description: | Abnormally high fuser middle thermistor 3 temperature Fuser middle thermistor 3 detects a temperature higher than 215°C/419°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 3. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6330 |
| Description: | Broken fuser center thermistor 3 wire Fuser center thermistor 3 detects a temperature lower than 20°C/ 68°F continuously for 1 s |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 3 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. |
| Error code: | 6520 |
| Description: | Abnormally high fuser thermistor 4 temperature Fuser thermistor 4 detects a temperature higher than 215°C/ 419°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 4. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6530 |
| Description: | Broken fuser thermistor 4 wire Fuser thermistor 4 detects a temperature lower than 20°C/ 68°F continuously for 1 s |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin Defective triac. Broken fuser thermistor 4 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6600 |
| Description: | Fuser belt rotation error A belt rotating pulse is not received for 1 s. (Engine CPU) |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser belt sensor. Defective engine PWB. |
| Remedy: | Fuser motor 1. To check the motor operation, execute U030 Fuser. 2. Check that the drive gear can rotate and not heavily loaded and, if necessary, apply grease to the axle holder and gears. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser motor and Feed PWB (YC18) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the fuser motor. Fuser belt sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6610 |
| Description: | Fuser release sensor error When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser release motor. Defective engine PWB. |
| Remedy: | Fuser release motor 1. To check the motor operation, execute U030 Fuser Release. 2. Check that the drive gear can be rotated and the separation is possible. 3. If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Fuser unit. Fuser release sensor 1. Check that the sensor is correctly positioned. 2. Check that the sensor is not contaminated or damaged. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6620 |
| Description: | IH core motor error When the IH core motor is driven, the IH core sensor does not turn off for 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective IH core motor. Defective eject PWB. Defective front PWB. Defective engine PWB. |
| Remedy: | IH core motor 1. To check the motor operation, execute U030 Fuser Release. 2. Check that the drive gear can be rotated and the separation is possible. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. IH core motor and front PWB (YC10) Front PWB (YC3) and engine PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Fuser unit. IH core sensor 1. Check that the sensor is correctly positioned. 2. Check that the sensor is not contaminated or damaged. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6710 |
| Description: | Fuser IH PWB CPU reset error Watch doc timer has been overflowed. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6720 |
| Description: | Fuser IH belt rotation error While driving, the pulse count is less than 3 for 2 seconds during the input to the rotation pulse signal is 200 msec. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser belt sensor. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser motor 1. To check the motor operation, execute U030 Fuser. 2. Check that the drive gear can rotate and not heavily loaded and, if necessary, apply grease to the axle holder and gears. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser motor and Feed PWB (YC18) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the fuser motor. Fuser belt sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6730 |
| Description: | Abnormally high fuser IH PWB temperature 1 (IGBT1) The input detect temperature is higher than 115°C/ 221 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB ( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6740 |
| Description: | Abnormally high fuser IH PWB temperature 2 (IGBT2) The input detect temperature is higher than 115°C/ 221 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB ( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6750 |
| Description: | Fuser IH output over-current error The output current of IH CPU is higher than 110 A for 10 ms in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6760 |
| Description: | Fuser IH input over-current error The input current of IH CPU is higher than 20A (100V/120V), 10A (200V) for 100 ms in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6770 |
| Description: | Fuser IH low electric power error Less than 0.6 times of the preset power is detected for 120 ms in succession after the IH heater remote has turned on. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Fuser IH PWB (YC6) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser IH unit. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6910 |
| Description: | Engine software ready error The device won’t engage in ready state in 60 minutes after warming-up has began. (A previous timeout process has not been cancelled. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser rear fan motor. Defective engine PWB. |
| Remedy: | Engine PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Reinstall the engine software. 3. Replace the engine PWB. |
| Error code: | 6920 |
| Description: | Fuser front fan motor error When the fuser front fan motor is driven, alarm signal is detected for 5 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser edge fan motor 1. Defective engine PWB. |
| Remedy: | Fuser front fan motor 1. To check the fan motor operation, execute U037 IH Coil. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser front fan motor and Front PWB (YC4) Front PWB (YC3) and Engine PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the fuser front fan motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6930 |
| Description: | Fuser rear fan motor error When the fuser rear fan motor is driven, alarm signal is detected for 5 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser edge fan motor 2. Defective engine PWB. |
| Remedy: | Fuser rear fan motor 1. To check the fan motor operation, execute U037 Fuser Cooling. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser rear fan motor and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the fuser rear fan motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6940 |
| Description: | IH PWB cooling fan motor error When the IH fan motor is driven, the alarm signal is detected for 5 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective IH fan motor. Defective engine PWB. |
| Remedy: | IH fan motor 1. To check the fan motor operation, execute U037 IH PWB. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. IH fan motor and Feed PWB 1(YC11) Feed PWB 1(YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the IH fan motor. Feed PWB 1 Replace the Feed PWB1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6950 |
| Description: | Fuser IH PWB communication error No response is received in 30 ms since a command is sent to IHCPU. A checksum error is detected 10 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC9) and Feed PWB 1(YC4) Power source PWB (YC3) and Fuser IH PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. If the +24V output is not given by the power source PWB (YC9), replace the power source PWB. Feed PWB 1 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and Fuser IH PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. If the +24V output is not given by the feed PWB1 (YC27), replace the feed PWB1. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6960 |
| Description: | Current PWB error The power current is greater than 1A for 5 seconds continuously despite that 500W was indicated as the fuser power during power-up. * : 220-240 V model only |
| Causes: | Defective current PWB. |
| Remedy: | Current PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Current PWB(YC17) and Feed PWB2 (YC13) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Current PWB. |
| Error code: | 6980 |
| Description: | Fuser EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6990 |
| Description: | Fuser power supply incompatibility Information won’t match between the engine backup and the fuser IH PWB. |
| Causes: | Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Differences in settings after initialization When this has happened after initialization using U021, make settings identical with the voltages on the IH PWB using U169. Fuser IH PWB Replace with a fuser IH PWB specifically designed with the standard voltage. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7001 |
| Description: | Toner motor error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB. |
| Remedy: | Toner container 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7101 |
| Description: | Toner sensor error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7200 |
| Display: | Jam MP Tray Remove the jammed paper from MP Tray and press [Retry]. |
| Description: | Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7210 |
| Description: | Short-circuited outer temperature sensor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7221 |
| Description: | Broken LSU thermistor wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LSU thermistor. Defective engine PWB. |
| Remedy: | LSU thermistor 1. Confirm LSU is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the laser scanner unit. LSU relay PWB REPLACE the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7231 |
| Description: | Short-circuited LSU thermistor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LSU thermistor. Defective engine PWB. |
| Remedy: | LSU thermistor 1. Confirm LSU is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the laser scanner unit. LSU relay PWB Replace the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7241 |
| Description: | Broken developer thermistor wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer thermistor. Defective engine PWB. |
| Remedy: | Developer thermistor 1. Confirm Developing is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7251 |
| Description: | Short-circuited developer thermistor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer thermistor. Defective engine PWB. |
| Remedy: | Developer thermistor 1. Confirm Developing is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7301 |
| Description: | Toner hopper motor error During the Toner hopper motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective toner hopper sensor. Defective toner hopper motor. Defective engine PWB. |
| Remedy: | Toner hopper motor 1. If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner hopper motor and Front PWB (YC5) Front PWB (YC3) and Engine PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the toner hopper motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7401 |
| Description: | Developer unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Different type of the developer unit is installed. Install the developer unit of the correct type. Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7411 |
| Description: | Drum unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the drum unit is installed. |
| Remedy: | Different type of the drum unit is installed. Install the drum unit of the correct type. Drum unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum unit and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7460 |
| Description: | Developer shutter error Power is turned on while the developer shutter is locked. |
| Causes: | The developer shutter has been locked. Defective connector cable or poor contact in the connector. |
| Remedy: | The developer shutter has been locked. Release the developer shutter. Developer shutter sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer shutter sensor and Front PWB (YC4) Front PWB (YC3) and Engine PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7470 |
| Description: | Failure of the fan motor that avoids internal contamination The toner fan motor signal has been detected as unconnected at power up. |
| Remedy: | Toner disposal box 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner disposal box and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Toner disposal box. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7601 |
| Description: | ID sensor 1 error [Front] Dark potential error FrontDarkP and FrontDarkS are greater than 0.80V. Light potential error FrontBrightS is smaller than FrontDarkS. FrontBrightP is smaller than [FrontDarkP + 0.5V]. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | ID sensor1 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor 1 (front) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7602 |
| Description: | ID sensor 2 error [Rear] Dark potential error RearDarkP and RearDarkS are greater than 0.80V. Light potential error RearBrightS is smaller than RearDarkS. RearBrightP is smaller than [RearDarkP + 0.5V]. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | ID sensor 2 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor2 (rear) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7901 |
| Description: | Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB. |
| Remedy: | DR PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7911 |
| Description: | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit. |
| Remedy: | Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7941 |
| Description: | Laser scanner unit EEPROM error Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective APC PWB. |
| Remedy: | APC PWB 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. APC PWB and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, shorted or grounded, replace the FFC wiring. 3. Replace the laser scanner unit. LSU relay PWB Replace the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8000 |
| Display: | Print Overrun |
| Description: | Finisher incompatible detection error The finisher has been installed with a device to which it is incompatible. |
| Causes: | The finisher is installed with a device to which it is incompatible. |
| Remedy: | The finisher is installed with a device to which it is incompatible. The finisher must be installed with the devices to which it is compatible. |
| Error code: | 8010 |
| Description: | Punch motor error 1 When the punch motor is driven, punch home position sensor does not turn on within 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch home position sensor. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch home position sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch home position sensor and Punch PWB (YC8) 4. Replace the Punch home position sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8020 |
| Description: | Punch motor error 2 Home position is not obtained in 3 s after home position is initialized or in standby. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8030 |
| Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8090 |
| Description: | DF paddle motor error When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF paddle sensor. Defective DF paddle motor. Defective DF main PWB. |
| Remedy: | DF paddle motor 1. Execute U240 Motor - Beat to check the finisher operation. 2. Check that the paddle can rotate. 3. Check that the drive from the motor reaches the paddle. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle motor and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF paddle motor. DF paddle sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8100 |
| Description: | DF eject release motor error When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF bundle discharge sensor. Defective DF eject release motor. Defective DF main PWB. |
| Remedy: | DF eject release motor DF bundle discharge unit sensor 1. Execute U240 Motor - Eject Unlock (Full) to check the finisher operation. 2. Check that the eject guide of the process tray is opened and, if not, correct the guide. 3. Check that the drive from the motor reaches the eject guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF eject release motor. DF bundle discharge unit sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 4. Replace the DF bundle eject unit sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8110 |
| Description: | DF shift motor 1 error DF shift sensor 1 won’t turn on when it has travelled 160 mm after DF shift motor 1 is driven. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift sensor 1. Defective DF shift motor 1. Defective DF main PWB. |
| Remedy: | DF shift motor 1 [front] 1. Execute U240 Motor - Sort Test to check the finisher operation. 2. Manipulate the front shift guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front shift guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift motor 1[front] and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift motor 1 [front]. DF shift sensor 1 [front] 1. Execute U241 Finisher - Shift Front HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift sensor 1[front] and DF main PWB (YC23) 4. Replace the DF shift sensor 1 [front]. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8120 |
| Description: | DF shift motor 2 error DF shift sensor 2 won’t turn on when it has travelled 160 mm after DF shift motor 2 is driven. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift sensor 2. Defective DF shift motor 2. Defective DF main PWB. |
| Remedy: | DF shift motor 2 [rear] 1. Execute U240 Motor - Sort Test to check the finisher operation. 2. Manipulate the rear shift guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear shift guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift motor 2 [rear] and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift motor 2 [rear]. DF shift sensor 2 [rear] 1. Execute U241 Finisher - Shift Tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift sensor 2 [rear] and DF main PWB (YC23) 4. Replace the DF shift set sensor2 [rear]. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8130 |
| Description: | DF shift release motor error When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift release sensor. Defective DF shift release motor. Defective DF main PWB. |
| Remedy: | DF shift release motor 1. Check that cancelling the maintenance mode after executing U240 Motor - Sort for the finisher operation check lets the rear and forth cursors return to the home position. 2. Manipulate the front and rear shift guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the shift guide front and rear. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift release motor and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift release motor. DF shift release sensor 1. Execute U241 Finisher - Shift Unlock HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift release sensor and DF main PWB (YC23) 4. Replace the DF shift release sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8150 |
| Description: | DF tray motor error 2 When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF main PWB (YC22) DF tray upper surface sensor and DF main PWB (YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8160 |
| Description: | DF tray motor error 3 When the main tray has descended, DF tray sensor 4 does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF tray sensor 3. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 4 1. Execute U241 Finisher - Tray Middle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 4 and DF main PWB (YC23) 4. Replace the DF tray sensor 4. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8170 |
| Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8180 |
| Description: | DF side registration motor 1 error 2 JAM6810 (jam in front of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1. 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8190 |
| Description: | DF side registration motor 2 error 1 When initial operation, DF side registration sensor 2 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8200 |
| Description: | DF side registration motor 2 error 2 JAM6910 (jam in rear of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8230 |
| Description: | DF staple motor error 1 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF staple sensor Replace the staple unit. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8240 |
| Description: | DF staple motor error 2 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8260 |
| Description: | DF middle motor home position error DF paddle sensor is not turned on within 1s after driving the DF middle motor. |
| Causes: | DF middle motor. DF paddle sensor. DF main PWB |
| Remedy: | DF middle motor 1. Execute U240 Motor - Middle(H)(L). 2. Check that the drive from the motor reaches the paddle. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF middle motor and DF main PWB (YC12) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF middle motor. DF paddle sensor 1. Execute U241 Finisher - Lead Paddle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8300 |
| Description: | CF unit communication error Communication with the center- folding unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF set sensor. Defective PWB. |
| Remedy: | CF unit set switch 1. Execute U241 Booklet - Set to check the finisher switch. 2. Check that the switch and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main PWB (YC7) and DF main PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CF unit set switch. CF main PWB Replace the CF main PWB DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8310 |
| Description: | CF side registration motor 2 error When initial operation, CF side registration sensor 2 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 2. Defective CF side registration motor 2. Defective CF main PWB. |
| Remedy: | CF side registration motor 2 1. Execute U240 Booklet - Width Test to check finisher operation check. 2. Manipulate the side registration upper guide back and forth to check it can smoothly move back and forth. 3. Check that the drive from the motor reaches the side registration upper guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor. CF side registration sensor 2 1. Execute U241 Booklet - Width Up HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 2 and CF main PWB (YC20) 4. Replace the CF side registration sensor 2. CF main PWB Replace the CF main PWB |
| Error code: | 8320 |
| Description: | CF adjustment motor error When initial operation, CF adjustment sensor does not turn on within 2.5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF adjustment sensor 1, 2. Defective CF adjustment motor 1, 2. Defective CF main PWB. |
| Remedy: | CF adjustment motor1,2 1. Execute U240 Booklet - Bundle Up / Down to check the finisher operation. 2. Manipulate the fold moving belt up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold moving belt. (Check if the belt is bent.) 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment motor 1,2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF adjustment motor1,2 CF adjustment sensor1,2 1. Execute U241 Booklet - bundle Up / Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment sensor 1,2 and CF main PWB (YC20) 4. Replace the CF adjustment sensor1,2. CF main PWB Replace the CF main PWB. |
| Error code: | 8330 |
| Description: | CF blade motor error When initial operation, CF blade sensor does not turn on within 1500 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF blade sensor. Defective CF blade motor. Defective CF main PWB. |
| Remedy: | CF blade motor 1. Execute U240 Booklet - Blade to check the finisher operation. 2. Manipulate the fold blade up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold blade. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade motor and CF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF blade motor. CF blade sensor 1. Execute U241 Booklet - Blade HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade sensor and CF main PWB (YC20) 4. Replace the CF blade sensor. CF main PWB Replace the CF main PWB |
| Error code: | 8340 |
| Description: | CF staple motor error 1 Staple JAM (center-folding unit) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF staple sensor. Defective CF staple motor. Defective CF main PWB. |
| Remedy: | CF staple motor 1. Execute U240 Booklet - Staple to check the finisher operation. 2. Manipulate the staple up and down check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF staple unit and CF main PWB (YC13) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF staple motor. CF staple sensor Replace the CF staple unit. CF main PWB Replace the CF main PWB. |
| Error code: | 8350 |
| Description: | CF side registration motor 1 error When initial operation, CF side registration sensor 1 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 1. Defective CF side registration motor 1. Defective CF main PWB |
| Remedy: | CF side registration motor 1 1. Execute U240 Booklet - Width Test to check the finisher operation. 2. Manipulate the side registration lower guide back and forth to check it can smoothly operable. 3. Check that the drive from the motor reaches the side registration lower guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 1 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor 1. CF side registration sensor 1 1. Execute U241 Booklet - Width Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 1 and CF main PWB (YC20) 4. Replace the CF side registration sensor 1. CF main PWB Replace the CF main PWB |
| Error code: | 8360 |
| Description: | CF main motor error During driving the motor, the lock signal is detected for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF main motor. Defective CF main PWB. |
| Remedy: | CF main motor 1. Execute U240 Booklet - Folding to check the finisher operation. 2. Manipulate the conveying roller to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main motor and CF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF main motor. CF main PWB Replace the CF main PWB |
| Error code: | 8410 |
| Description: | Punch slide motor error 1 The punch slide sensor won’t turn On when home position has been moved by 30 mm. |
| Causes: | Defective connector cable or poor contact in the connector. Defective slide sensor. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch slide sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide sensor and Punch PWB (YC6) 4. Replace the punch slide sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8420 |
| Description: | Punch slide motor error 2 In detection of paper edges, the paper edge cannot be detected in 30 mm move. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch paper edge sensor 1,2 1. Execute U241 Punch - Edge Face 1,2,3,4 to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch paper edge sensor 1,2 and Punch PWB (YC5,YC7) 4. Replace the punch paper edge sensor 1,2. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8430 |
| Description: | Punch unit communication error Communication with the punch unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8500 |
| Description: | Mailbox communication error Communication failed to be established after the mailbox was hooked up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | MB main PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB main PWB (YC3) and DF main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB main PWB DF main PWB Replace the DF main PWB |
| Error code: | 8510 |
| Description: | MB conveying motor error 1 When initial operation, MB home position sensor does not turn on within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor. Defective MB main PWB. |
| Remedy: | MB conveying motor 1. If the transfer roller won’t rotate smoothly, repair its mechanism. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
| Error code: | 8520 |
| Description: | MB conveying motor error 2 When standby operation, MB home position sensor does not turn off within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor Defective MB main PWB. |
| Remedy: | MB conveying motor 1. Execute Mail Box - Conv of U240 finisher operation check. 2. Manipulate the conveying roller of the mailbox to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
| Error code: | 8800 |
| Description: | Document finisher main program error Document finisher main program error at power up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8900 |
| Description: | Document finisher backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective DF main PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB |
| Error code: | 8930 |
| Description: | Center-folding unit backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective CF main PWB. |
| Remedy: | CF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main PWB (YC7) and DF main PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Install the EEPROM properly. 4. Replace the CF main PWB |
| Error code: | 9000 |
| Description: | Document processor communication error Communication with the document processor is not possible. |
| Causes: | Defective connector cable or poor contact in the connector Defective PWB. |
| Remedy: | DP main PWB 1. Check that the versions of the main unit firmware and the DP firmware are identical. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP main PWB(YC1) and ISC PWB(YC12) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP main PWB ISC PWB Replace the ISC PWB. |
| Error code: | 9010 |
| Description: | Coin vender communication error A communication error from coin vender is detected 10 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Data setup failure. Defective coin vender control PWB. Defective PWB. |
| Remedy: | U206 setting Set maintenance mode U206 to off when a coin vender is not installed. Coin vender control PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Coin vender control PWB and Engine PWB (YC23) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Coin vender control PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 9040 |
| Description: | DP lift motor going up error When the DP lift motor is driven, DP lift sensor 1 does not turn on within 1500 pulse. (Three recovery times.) The above has been detected 5 times. * : The number of detection should be weighted with one for the rise at job start and two for the irregular rise during transporting. The accumulated number must be cleared at completion of a normal rise. The default threshold is 5. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP lift sensor 1. Defective DP lift motor. Defective DP main PWB. |
| Remedy: | DP lift motor 1. Execute U906 Separating Operation Release. 2. Execute U243 Lift Motor to check the DP motor operation. 3. Check that the original document lift guide can move upwards. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift motor and DP main PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DP lift motor. DP lift sensor 1 1. Execute U244 Lift L-Limit to check DP switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift sensor 1 and DP main PWB (YC4) 4. Replace the DP lift sensor 1. DP main PWB Replace the DP main PWB |
| Error code: | 9050 |
| Description: | DP lift motor going down error When the DP lift motor is driven, DP lift sensor 2 does not turn on within 1500 pulse. (Three recovery times.) The above has been detected 1 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP lift sensor 2. Defective DP lift motor. Defective DP main PWB. |
| Remedy: | DP lift motor 1. Execute U906 Separating Operation Release. 2. Execute U243 Lift Motor to check the DP motor operation. 3. Check that the original document lift guide can move downwards. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift motor and DP main PWB (YC5) If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DP lift motor. DP lift sensor 2 1. Execute U244 Lift L-Limit to check DP switch. 2. Confirm that the DP lift sensor 2 has been firmly fitted. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift sensor 2 and DP main PWB (YC2) 4. Replace the DP lift sensor2. DP main PWB Replace the DP main PWB |
| Error code: | 9060 |
| Description: | DP EEPROM error Mismatch of reading data from two locations occurs 3 times successively. Mismatch between writing data and reading data occurs 3 times successively. |
| Causes: | Defective DP main PWB. Device damage of EEPROM. |
| Remedy: | DP main PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the EEPROM has been properly installed. 3. Replace the DP main PWB Device damage of EEPROM Contact the Service Support. |
| Error code: | 9070 |
| Description: | Communication error between DP and SHD A communication error is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DPSHD PWB. |
| Remedy: | DP SHD PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP SHD PWB. |
| Error code: | 9080 |
| Description: | LED fault detection A block is existent below a peak which was obtained by activating the LEDs in the four CIS blocks at power on, which is less than 80hex. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS Defective DPSHD PWB. |
| Remedy: | DP CIS 1. Execute CIS automatic original document alignment by U411. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DP SHD PWB (YC2) DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the CIS and execute U411. DP SHD PWB Replace the DP SHD PWB. |
| Error code: | 9100 |
| Description: | Coin vender control PWB error Communication error has been detected at the coin mec of the coin vender control PWB. |
| Causes: | Defective coin vender control PWB. |
| Remedy: | Coin vender control PWB Replace the coin mec. |
| Error code: | 9110 |
| Description: | Coin vender rejector error Communication error has been detected in connection with the coin mec and the rejector. |
| Causes: | Rejector installed incorrectly. Defective rejector. |
| Remedy: | Rejector 1. Check that the rejector is firmly installed and, if not, install firmly. 2. Replace the rejector. |
| Error code: | 9120 |
| Description: | Sensor error in coin vender change (Yen 10) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9130 |
| Description: | Sensor error in coin vender change (Yen 50) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9140 |
| Description: | Sensor error in coin vender change (Yen 100) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9150 |
| Description: | Sensor error in coin vender change (Yen 500) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Change tube Check no exchange jam is observed at the outlet and, if necessary, repair it. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9160 |
| Description: | Coin vender pay-out error Coin is paid out despite the pay-out motor is determined not active. |
| Causes: | Defective pay-out motor. |
| Remedy: | Pay-out motor Replace the coin mec. |
| Error code: | 9170 |
| Description: | Coin vender pay-out sensor error Coin is paid out despite the pay-out motor is determined not active. |
| Causes: | Change jam at the pay-out. Defective pay-out motor. Defective pay-out sensor. |
| Remedy: | Pay-out area Check no exchange jam is observed at the outlet and, if necessary, repair it. Pay-out motor Replace the coin mec. Pay-out sensor Replace the coin mec. |
| Error code: | 9500 |
| Description: | ISC PWB error A |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC PWB 4. Contact the Service Support. |
| Error code: | 9510 |
| Description: | ISC PWB error B |
| Causes: | Main PWB. DP SHD PWB. |
| Remedy: | Main PWB DP SHD PWB 1. Reinsert the connector if its connection is loose. DP relay PWB (YC2) and DP SHD PWB (YC3) 2. Replace the main PWB. 3. Replace the DP SHD PWB. 4. Contact the Service Support. |
| Error code: | 9520 |
| Description: | ISC PWB error C |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC main PWB 4. Contact the Service Support. |
| Error code: | 9940 |
| Description: | Confidential document guard uninstalled error The confidential document guard PWB is removed while the confidential document guard PWB is valid. |
| Causes: | Confidential document guard PWB |
| Remedy: | Confidential document guard PWB 1. Check that the confidential document guard PWB is firmly installed and, if not, install firmly. 2. Replace the confidential document guard PW. |
| Error code: | 9950 |
| Description: | ISC PWB error C FPGA configuration error CPU version information error This is caused when the PWB of a double-side scanning DP is connected, the confidential guard PWB is inserted, and the harness is not correctly connected |
| Causes: | Confidential document guard PWB |
| Remedy: | Confidential document guard PWB 1. Replace the confidential document guard PW. 2. Replace the main PWB. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F041 |
| Description: | Over than available setting number tray detection error |
| Causes: | Over than available setting number tray is installed. |
| Remedy: | Remove the available setting number tray. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F051 |
| Description: | Scanner engine program error |
| Causes: | The scanner program cannot start up |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The scanner engine RAM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the SSD The SSD is not properly attached. Reattach the SSD. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F12X |
| Description: | An error is detected at the Scan control section |
| Remedy: | 1) Check connection of the harness (Scan/DP - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the Scan/DP board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F13X |
| Description: | An error is detected at the Panel control section |
| Remedy: | 1) Check connection of the harness (Panel - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the panel board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F14X |
| Description: | An error is detected at the FAX control section |
| Remedy: | 1) Check connection of the harness (FAX - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check function. (Take cae of the received data since it is cleared) 5) Replace the FAX_DIMM and check function. 6) Replace the FAX board and check function. 7) Replace the main board and check function. 8) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F15X |
| Description: | An error is detected at the authentication device control section |
| Remedy: | 1) Check connection of the harness (Authentication device - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F17X |
| Description: | An error is detected at the print data control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F18X |
| Description: | An error is detected at the Video control secion |
| Remedy: | 1) Check connection of the harness (Engine - Main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the engine board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F1CX |
| Description: | An error is detected at the File System management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F1DX |
| Description: | An error is detected at the Image memory management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. *The F1D4 error is RAM allocation error. -1Check it with the U340 -2Initialize the setting valued with the U021 |
| Error code: | F21X, F22X, F23X |
| Description: | An error is detected at the Image processing section |
| Remedy: | 1) Check contact of the DDR memory and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F24X |
| Description: | An error is detected at the System management section |
| Remedy: | 1) Check contact of the DDR memory and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the main board and check function. 5) Replace the HDD and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F25X |
| Description: | An error is detected at the Network management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Retrieve the USBLOG and contact the Service Administratuve Division. (or retrieve the packet capture data depending on the reult of analysis) |
| Error code: | F26X ... F2AX |
| Description: | An error is detected at the System management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F278 |
| Description: | Secondary power source error |
| Causes: | The operation became unstable since the primary supply power dropped out temporarily and recovered. |
| Remedy: | 1 Resetting the main power The power reset was performed immediately. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected or the wire is faulty. Clean the connectors on the LVU and reinsert the wire connectors. If there is no continuity, replace the wire. 3 Replacing the LVU The LVU is faulty. Replace the LVU. |
| Error code: | F33X |
| Description: | An error is detected at the Scan management section |
| Remedy: | 1) Check connection of the harness (Scan/DP board - main board) and connectors and check function. 2) Format the HDD and check function. (U024 FULL formatting) 3) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 4) Replace the Scan/DP board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F34X |
| Description: | An error is detected at the Panel management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F35X |
| Description: | An error is detected at the Print control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F36X |
| Description: | An error is detected at the Print management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F37X |
| Description: | An error is detected at the FAX management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check function. (Take cae of the received data since it is cleared) 4) Replace the FAX_DIMM and check function. 5) Replace the main board and check function. 6) Replace the HDD and check function. 7) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F38X |
| Description: | An error is detected at the Authentication/permit management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F3AX ... F45X |
| Description: | An error is detected at the Entity management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F46X |
| Description: | An error is detected at the Print image process section |
| Remedy: | 1) Replace the main board and check function. 2) Retrieve the USBLOG (or retrieve the print capture data by case) |
| Error code: | F47X ... F49X |
| Description: | An error is detected at the Image edit process control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F4AX, F4CX |
| Description: | An error is detected at the Print image process section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F4DX, F4EX |
| Description: | An error is detected at the Entity control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F4FX |
| Description: | An error is detected at the Job control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F50X |
| Description: | An error is detected at the FAX control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F51X ... F57X |
| Description: | An error is detected at the Job execution section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F58X ... F5EX |
| Description: | An error is detected at the Service management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F5FX |
| Description: | An error is detected at the Service execution section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F60X |
| Description: | An error is detected at the Maintenance mode management section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F61X |
| Description: | An error is detected at the Report compiling section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F62X |
| Description: | An error is detected at the Service execution section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F63X |
| Description: | An error is detected at the Device control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F64X ... F67X |
| Description: | An error is detected at the Print image process section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F68X |
| Description: | An error is detected at the Storage device control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F69X ... F6CX |
| Description: | An error is detected at the HyPAS control section |
| Remedy: | 1) Format the HDD and check function. (U024 FULL formatting) 2) Execute the U021 Memory initializing to initialize the controller backup memory and check function. 3) Replace the main board and check function. 4) Replace the HDD and check function. 5) Retrieve the USBLOG and contact the Service Administrative Division. |
| Error code: | F6DX ... F75X |
| Description: | An error is detected at the External Server management section |
| Remedy: | 1) Check the external server and check function. 2) Chekc the connection to the external server and check function. 3) Check the network settings and check function. 4) Replace the bridge board and check function. 5) Replace the main board and check function. 6) Retrieve the USBLOG and contact the Service Administrative Division. |
Название
Kyocera Контейнер для отработанного тонера
Kyocera Блок фотобарабана
Kyocera Блок проявки
Kyocera Узел термозакрепления, левая часть. 230v
Kyocera Узел термозакрепления, правая часть. 230v
Kyocera Нижняя часть печки в сборе
Kyocera Сервисный комплект
Kyocera Сервисный комплект 230V
Kyocera Тонер-картридж черный
