Brother MFC-B7715DW
Рейтинг
Модули
DOCUMENT SCANNER
COVER
FRAME L&DRIVE UNIT
PCB
PAPER CASSETTE
FRAME
ADF & DOCUMENT COVER
FUSER UNIT
PANEL
LASER UNIT
DX
PAPER FEEDER
Детали ADF
| Деталь: | DOCUMENT SCANNER UNIT |
| Парткод: | D00X7Y001 |
| Деталь: | DOCUMENT SCANNER UNIT |
| Парткод: | D00UU2001 |
| Деталь: | DOCUMENT SCANNER UNIT |
| Парткод: | D00UTG001 |
| Деталь: | DOCUMENT SCANNER UNIT |
| Парткод: | D00X80001 |
| Деталь: | DOCUMENT SCANNER UNIT |
| Парткод: | D00X81001 |
| Деталь: | DOCUMENT SCANNER UNIT |
| Парткод: | D00UU3001 |
| Деталь: | DOCUMENT SCANNER UNIT |
| Парткод: | D00UU5001 |
| Деталь: | DOCUMENT SCANNER UNIT |
| Парткод: | D00UU4001 |
| Деталь: | FIRST SIDE CIS UNIT |
| Парткод: | D00G04001 |
| Деталь: | FIRST SIDE CIS FLAT CABLE |
| Парткод: | D00L0U001 |
| Деталь: | FIRST SIDE CIS FLAT CABLE |
| Парткод: | D00G05001 |
| Деталь: | ADF CLEAN UP LABEL |
| Парткод: | D00ATN001 |
| Деталь: | ADF CLEAN UP LABEL |
| Парткод: | D00ATX001 |
| Деталь: | PANEL FLAT CABLE |
| Парткод: | D009GD001 |
| Деталь: | PANEL FLAT CABLE |
| Парткод: | D009GC001 |
| Деталь: | JOINT COVER ASSY |
| Парткод: | D00X4C001 |
| Деталь: | JOINT COVER ASSY |
| Парткод: | D00X4B001 |
| Деталь: | JOINT COVER ASSY |
| Парткод: | D00X4D001 |
| Деталь: | JOINT COVER ASSY |
| Парткод: | D00X4G001 |
| Деталь: | JOINT COVER ASSY |
| Парткод: | D00X4E001 |
| Деталь: | JOINT COVER ASSY |
| Парткод: | D00X4H001 |
| Деталь: | SIDE COVER L DCP ASSY |
| Парткод: | D00BZ1003 |
| Деталь: | SIDE COVER L DCP ASSY |
| Парткод: | D00BZ1001 |
| Деталь: | SIDE COVER L DCP ASSY |
| Парткод: | D00BZ1005 |
| Деталь: | SIDE COVER L DCP ASSY |
| Парткод: | D00MY0005 |
| Деталь: | SIDE COVER L FB ASSY |
| Парткод: | D00AS4003 |
| Деталь: | SIDE COVER L FB ASSY |
| Парткод: | D00AS4001 |
| Деталь: | SIDE COVER L FB ASSY |
| Парткод: | D00AS4005 |
| Деталь: | SIDE COVER R ASSY |
| Парткод: | D00HZR003 |
| Деталь: | SIDE COVER R ASSY |
| Парткод: | D00HZR001 |
| Деталь: | SIDE COVER R ASSY |
| Парткод: | D00HZR005 |
| Деталь: | SIDE COVER R ASSY |
| Парткод: | D00BZ6003 |
| Деталь: | SIDE COVER R ASSY |
| Парткод: | D00BZ6001 |
| Деталь: | SIDE COVER R ASSY |
| Парткод: | D00BZ6005 |
| Деталь: | BACK COVER |
| Парткод: | D00AYZ005 |
| Деталь: | BACK COVER |
| Парткод: | D00AYZ003 |
| Деталь: | BACK COVER |
| Парткод: | D00AYZ001 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00VK0003 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00MY5003 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00MY5001 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00AS8001 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00S1C001 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00MY5005 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00US9005 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00AS8005 |
| Деталь: | FRONT COVER ASSY |
| Парткод: | D00S1C005 |
| Деталь: | INNER CHUTE ASSY |
| Парткод: | LY9130004 |
| Деталь: | INNER CHUTE ASSY |
| Парткод: | LY9130002 |
| Деталь: | INNER CHUTE ASSY |
| Парткод: | LY9130001 |
| Деталь: | FUSER COVER |
| Парткод: | D00AL5001 |
| Деталь: | OUTER CHUTE ASSY |
| Парткод: | LY9146001 |
| Деталь: | LAN PORT CAP |
| Парткод: | D001BD001 |
| Деталь: | MJ COVER EXT |
| Парткод: | UF5745000 |
| Деталь: | EXT CAP |
| Парткод: | LE8842001 |
| Деталь: | SPEAKER |
| Парткод: | LT3253001 |
| Деталь: | CODE HOOK |
| Парткод: | LX9044002 |
| Деталь: | CODE HOOK |
| Парткод: | LX9044001 |
| Деталь: | PAPER STOPPER |
| Парткод: | LEM005004 |
| Деталь: | PAPER STOPPER |
| Парткод: | LEM005002 |
| Деталь: | PAPER STOPPER |
| Парткод: | LEM005003 |
| Деталь: | FRAME L UNIT SP |
| Парткод: | D00WXC001 |
| Деталь: | FRAME L UNIT SP |
| Парткод: | D00WX9001 |
| Деталь: | FRAME L UNIT SP |
| Парткод: | D00WXD001 |
| Деталь: | EJECT SENSOR PCB ASSY |
| Парткод: | LV1288001 |
| Деталь: | FUSER GEAR 64R/36R |
| Парткод: | D00ALH001 |
| Деталь: | MAIN MOTOR |
| Парткод: | D00AN7001 |
| Деталь: | MAIN MOTOR FLAT CABLE |
| Парткод: | D00G2C001 |
| Деталь: | FRONT COVER SENSOR |
| Парткод: | D00ASE001 |
| Деталь: | TONER BOX NEW PCB ASSY |
| Парткод: | D00F1H001 |
| Деталь: | TONER SENSOR PCB ASSY |
| Парткод: | D00KH4001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZA001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZH001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00PLS002 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00P17001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00HE0002 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00P1B001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00RBK002 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZD002 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZB001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZF001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00P1D001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00HE0001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZJ004 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZJ001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00J54001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00PLT002 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00HE2004 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00HE2001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00HE2002 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00PS7004 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00PS7002 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZM001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00P26001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZT004 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZT002 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00MZT001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00HE4004 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00P29001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00HE4001 |
| Деталь: | MAIN PCB ASSY |
| Парткод: | D00HE4002 |
| Деталь: | MODEM PCB ASSY |
| Парткод: | D0092S001 |
| Деталь: | LOW VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00HCK001 |
| Деталь: | LOW VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00MNX001 |
| Деталь: | LOW VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00HKR001 |
| Деталь: | LOW VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00HCG001 |
| Деталь: | LOW VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00JUZ001 |
| Деталь: | LOW VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00HCF001 |
| Деталь: | LOW VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00JV0001 |
| Деталь: | LOW VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00MNW001 |
| Деталь: | HIGH VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D0092T002 |
| Деталь: | HIGH VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D0092T001 |
| Деталь: | HIGH VOLTAGE POWER SUPPLY PCB ASSY |
| Парткод: | D00HC2001 |
| Деталь: | HIGH VOLTAGE POWER SUPPLY PCB |
| Парткод: | D0092T001 |
| Деталь: | HIGH VOLTAGE POWER SUPPLY PCB |
| Парткод: | D00HC2001 |
| Деталь: | MODEM FLAT CABLE |
| Парткод: | D00G37001 |
| Деталь: | PAPER TRAY |
| Парткод: | D00HEA003 |
| Деталь: | PAPER TRAY |
| Парткод: | D00AR5003 |
| Деталь: | PAPER TRAY |
| Парткод: | D00HEA001 |
| Деталь: | PAPER TRAY |
| Парткод: | D00AR5001 |
| Деталь: | PAPER TRAY |
| Парткод: | D00HEA005 |
| Деталь: | PAPER TRAY |
| Парткод: | D00AR5005 |
| Деталь: | T1 CLUTCH |
| Парткод: | D00APE001 |
| Деталь: | FILTER |
| Парткод: | D00HB6001 |
| Деталь: | FAN |
| Парткод: | LY9348001 |
| Цена: | 1 400 ₽ |
| Деталь: | HVPS FLAT CABLE |
| Парткод: | D00ASJ001 |
| Деталь: | NEW TONER SENSOR PCB ASSY |
| Парткод: | D00ASF001 |
| Деталь: | REGISTRATION CLUTCH ASSY |
| Парткод: | D00APK001 |
| Деталь: | WIRELESS LAN PCB ASSY |
| Парткод: | LD1969001 |
| Деталь: | TONER BOX RELAY PCB ASSY |
| Парткод: | D00ASS001 |
| Деталь: | ADF UNIT |
| Парткод: | D00WY4001 |
| Деталь: | ADF UNIT |
| Парткод: | D00WY0001 |
| Деталь: | ADF UNIT |
| Парткод: | D00WY3001 |
| Деталь: | ADF UNIT |
| Парткод: | D00WY5001 |
| Деталь: | DOCUMENT COVER ASSY |
| Парткод: | D00X8B001 |
| Деталь: | DOCUMENT COVER ASSY |
| Парткод: | D00UUD001 |
| Деталь: | DOCUMENT COVER ASSY |
| Парткод: | D00UUE001 |
| Деталь: | DOCUMENT COVER ASSY |
| Парткод: | D00X8D001 |
| Деталь: | DOCUMENT STOPPER ASSY |
| Парткод: | D008VF001 |
| Деталь: | DOCUMENT STOPPER ASSY |
| Парткод: | D008VF002 |
| Деталь: | SEPARATE HOLDER ASSY |
| Парткод: | D008V0001 |
| Деталь: | SEPARATE ROLLER ASSY |
| Парткод: | D008UZ001 |
| Деталь: | SECOND SIDE CIS FLAT CABLE |
| Парткод: | D00G06001 |
| Деталь: | SECOND SIDE CIS UNIT |
| Парткод: | D00G04001 |
| Деталь: | CIS SPACER |
| Парткод: | D008W0001 |
| Деталь: | ADF COVER ASSY |
| Парткод: | D008V3002 |
| Деталь: | ADF COVER ASSY |
| Парткод: | D008V3001 |
| Деталь: | DOCUMENT SUB TRAY ASSY |
| Парткод: | D008V9002 |
| Деталь: | DOCUMENT SUB TRAY ASSY |
| Парткод: | D008V9001 |
| Деталь: | DOCUMENT SUB TRAY ASSY |
| Парткод: | D008V9003 |
| Деталь: | PANEL UNIT |
| Парткод: | D00HAX002 |
| Деталь: | PANEL UNIT |
| Парткод: | D00MSF002 |
| Деталь: | PANEL UNIT |
| Парткод: | D00R10001 |
| Деталь: | PANEL UNIT |
| Парткод: | D00HAX001 |
| Деталь: | PANEL UNIT |
| Парткод: | D00MSJ001 |
| Деталь: | PANEL UNIT |
| Парткод: | D00MSF001 |
| Деталь: | PANEL PCB ASSY |
| Парткод: | D009HE001 |
| Деталь: | LCD SHEET |
| Парткод: | D00MSA001 |
| Деталь: | LCD SHEET |
| Парткод: | D00MT6001 |
| Деталь: | LCD SHEET |
| Парткод: | D00R11001 |
| Деталь: | LCD SHEET |
| Парткод: | D00TV6001 |
| Деталь: | LCD SHEET |
| Парткод: | D00HAY001 |
| Деталь: | LCD SHEET |
| Парткод: | D00U2Y001 |
| Деталь: | LCD SHEET |
| Парткод: | D00S1H001 |
| Деталь: | LCD SHEET |
| Парткод: | D00R98001 |
| Деталь: | LCD SHEET |
| Парткод: | D00MD3001 |
| Деталь: | LCD SHEET |
| Парткод: | D00MF0001 |
| Деталь: | LCD SHEET |
| Парткод: | D00USW001 |
| Деталь: | LCD SHEET |
| Парткод: | D00U4A001 |
| Деталь: | LCD SHEET |
| Парткод: | D00MPT001 |
| Деталь: | PANEL UNIT 7715DW ENG |
| Парткод: | D00VP9001 |
| Деталь: | PANEL UNIT 7715DW ASA |
| Парткод: | D00J4Y001 |
| Деталь: | PANEL UNIT 7715DW POL |
| Парткод: | D00VPS001 |
| Деталь: | PANEL UNIT 2710DN GER |
| Парткод: | D00R5U001 |
| Деталь: | PANEL UNIT 2710DN ENG |
| Парткод: | D00R19001 |
| Деталь: | PANEL UNIT 2710DN FRA |
| Парткод: | D00R67001 |
| Деталь: | PANEL UNIT 2710DN ITA |
| Парткод: | D00R6M001 |
| Деталь: | PANEL UNIT 2710DW IBERIA |
| Парткод: | D00PXW001 |
| Деталь: | PANEL UNIT 2710DW US |
| Парткод: | D00HBA001 |
| Деталь: | PANEL UNIT 2710DW GER |
| Парткод: | D00PUJ001 |
| Деталь: | PANEL UNIT 2710DW ENG |
| Парткод: | D00HB8001 |
| Деталь: | PANEL UNIT 2710DW FRA |
| Парткод: | D00PXJ001 |
| Деталь: | PANEL UNIT 2710DW DUT |
| Парткод: | D00RJP001 |
| Деталь: | PANEL UNIT 2710DW ITA |
| Парткод: | D00PXP001 |
| Деталь: | PANEL UNIT 2710DW NOR-ENG |
| Парткод: | D00RLF001 |
| Деталь: | PANEL UNIT 2712DN POL |
| Парткод: | D00U37001 |
| Деталь: | PANEL UNIT 2712DN ENG |
| Парткод: | D00U41001 |
| Деталь: | PANEL UNIT 2712DW POL |
| Парткод: | D00U48001 |
| Деталь: | PANEL UNIT 2712DW ENG |
| Парткод: | D00U4J001 |
| Деталь: | PANEL UNIT 2713DW NZ |
| Парткод: | D00MW8001 |
| Деталь: | PANEL UNIT 2715DW TWN |
| Парткод: | D00MV9001 |
| Деталь: | PANEL UNIT 2715DW ASA |
| Парткод: | D00SAT001 |
| Деталь: | PANEL UNIT 2716DW TUR |
| Парткод: | D00U60001 |
| Деталь: | PANEL UNIT 2395DW |
| Парткод: | D00MT7001 |
| Деталь: | PANEL UNIT 2730DW |
| Парткод: | D00MXB001 |
| Деталь: | PANEL UNIT 2732DW |
| Парткод: | D00V5A001 |
| Деталь: | PANEL UNIT 2750DW |
| Парткод: | D00HB3001 |
| Деталь: | PANEL UNIT 2751DW |
| Парткод: | D00V7A001 |
| Деталь: | ADDRESS LABEL |
| Парткод: | D00HKT001 |
| Деталь: | PANEL COVER DCP DUT W |
| Парткод: | D00PPS001 |
| Деталь: | PANEL COVER DCP IBE W |
| Парткод: | D00PKX001 |
| Деталь: | PANEL COVER DCP ENG W |
| Парткод: | D00HAZ001 |
| Деталь: | PANEL COVER DCP POL W |
| Парткод: | D00U1X001 |
| Деталь: | PANEL COVER DCP IBE |
| Парткод: | D00PPT001 |
| Деталь: | PANEL COVER DCP ENG |
| Парткод: | D00R15001 |
| Деталь: | PANEL COVER DCP DUT |
| Парткод: | D00PS9001 |
| Деталь: | PANEL COVER DCP GER |
| Парткод: | D00MD4001 |
| Деталь: | PANEL COVER DCP FRE |
| Парткод: | D00PS8001 |
| Деталь: | PANEL COVER DCP ITA |
| Парткод: | D00PSF001 |
| Деталь: | PANEL COVER DCP RUS |
| Парткод: | D00USZ001 |
| Деталь: | PANEL COVER DCP POL |
| Парткод: | D00TVM001 |
| Деталь: | PANEL COVER MFC ENG W |
| Парткод: | D00HB9002 |
| Деталь: | PANEL COVER MFC POL W |
| Парткод: | D00U49002 |
| Деталь: | PANEL COVER MFC US W |
| Парткод: | D00HB0002 |
| Деталь: | PANEL COVER MFC US W |
| Парткод: | D00HB0001 |
| Деталь: | PANEL COVER MFC ENG W |
| Парткод: | D00HB9001 |
| Деталь: | PANEL COVER DCP POL W |
| Парткод: | D00U1X002 |
| Деталь: | PANEL COVER COVER DCP ENG W |
| Парткод: | D00HAZ002 |
| Деталь: | PANEL COVER DCP GER W |
| Парткод: | D00PBR001 |
| Деталь: | PANEL COVER DCP FRE W |
| Парткод: | D00PP2001 |
| Деталь: | FRENCH PANEL STICKER |
| Парткод: | D00M5T001 |
| Деталь: | PANEL PCB ASSY |
| Парткод: | D009HE002 |
| Деталь: | LCD |
| Парткод: | D00E11001 |
| Деталь: | PANEL PCB ASSY |
| Парткод: | D00HAV001 |
| Деталь: | LCD |
| Парткод: | D00CV4001 |
| Деталь: | PANEL PCB ASSY |
| Парткод: | D009H6001 |
| Деталь: | PANEL PCB ASSY |
| Парткод: | D00HAW001 |
| Деталь: | LCD SHEET |
| Парткод: | D00J52001 |
| Деталь: | LCD SHEET |
| Парткод: | D00R1C001 |
| Деталь: | LCD SHEET |
| Парткод: | D00HB1001 |
| Деталь: | LCD SHEET |
| Парткод: | D00U3B001 |
| Деталь: | LCD SHEET |
| Парткод: | D00U4B001 |
| Деталь: | LCD SHEET |
| Парткод: | D00MW9001 |
| Деталь: | LCD SHEET |
| Парткод: | D00MW7001 |
| Деталь: | LCD SHEET |
| Парткод: | D00U61001 |
| Деталь: | TOUCH PANEL |
| Парткод: | LT3174001 |
| Деталь: | LCD |
| Парткод: | D00HS0001 |
| Деталь: | KEY PCB ASSY |
| Парткод: | D009HP001 |
| Деталь: | NFC PCB ASSY |
| Парткод: | D00SVB001 |
| Деталь: | LASER UNIT (SP) |
| Парткод: | D008ZW001 |
| Деталь: | LASER UNIT (SP) |
| Парткод: | D00KEZ001 |
| Деталь: | LASER UNIT FLAT CABLE |
| Парткод: | D00916001 |
Коды ошибок
0102
0201
0300
0305
0401
0405
0501
0502
0503
0504
0505
0506
0508
050A
050B
050C
0900
0A02
0B01
0B02
2200
2400
2500
2E00
3A00
4000
4200
4B01
4B06
4C01
4C06
4D01
4E01
4F01
4F05
5E00
6001
6004
6101
6106
6200
6801
6901
6902
6A00
6F00
7000
7100
7200
7302
7800
8903
8904
8A01
8C00
8E01
8E02
9001
9002
9201
9202
9301
9302
9309
9701
9702
A000
A200
A300
A400
A500
A600
A700
A900
AC00
AD00
AF00
B000
BB00
BC00
BD00
BF00
C700
C800
D100
D200
D800
E000
E100
E500
E600
E701
E702
E900
F900
Описание
| Error code: | 0102 |
| Display: | MAINTENANCE CALL 0102 |
| Description: | Even though the machine carries out the regular movement, the output of Head Lock Sensor does not reach the expected value. |
| Causes: | Head Lock Sensor does not work correctly or is broken. |
| Remedy: | Head Lock Sensor replacement Check the mechanical backlash or loose with the scan axis related parts. |
| Error code: | 0201 |
| Display: | Print Unable 02 Turn the power off and then back on again. |
| Description: | Head 2 is abnormally hot. Head 2 temperature has reached 58°C and above. |
| Causes: | Thermistor (Head) has a problem. Flexible Cable has short circuitted or cut-line. |
| Remedy: | Check Flexible Cable connection around Head Head replacement |
| Error code: | 0300 |
| Display: | POLYGON MOTOR |
| Description: | Polygon motor malfunction |
| Causes: | • The polygon motor does not rotate evenly even after the lapse of a given period of time after it has been started. • The motor lock signal remains HIGH for a given period of consecutive time while the polygon motor is being rotated. |
| Remedy: | 1 Check the cable and connector for proper connection and correct as necessary. - - 2 Change PH unit. - - 3 Change PRCB. - - |
| Error code: | 0305 |
| Description: | ROM Checksum Failure |
| Remedy: | Replace the system board. |
| Error code: | 0401 |
| Display: | Print Unable 04 Turn the power off and then back on again. |
| Description: | BD sensor 1 damaged. |
| Remedy: | 1 Connection failure of the polygon motor harness Reconnect the polygon motor harness. 2 Laser unit failure Replace the laser unit. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 0405 |
| Description: | Cannot detect the synchronized signal of the polygon motor for the laser unit (first time). |
| Remedy: | 1 Connection failure of the laser unit flat cable Reconnect the laser unit flat cable. 2 Laser unit flat cable failure Replace the laser unit flat cable. 3 Laser unit failure Replace the laser unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 0501 |
| Display: | FUSER ERROR |
| Description: | Fusing Pressure Roller warm-up failure • The Fusing Pressure Roller Thermistor/1 (TH2) fails to raise a given degree of temperature even after the lapse of a given period of time after the Fusing Pressure Heater Lamp (H3) is turned ON. • The detected temperature of the Fusing Pressure Roller Thermistor/1 (TH2) is lower for a given level of degree than one of the Heating Roller Thermistor/1 (TH1) after the Front Door is opened or closed, the Main Power Switch is turned ON or TROUBLE RESET is implemented. |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure |
| Remedy: | 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-M. 5 Change PU1. |
| Error code: | 0502 |
| Display: | Thermistor failure CODE (0502) Turn power off, on |
| Description: | 0502 Thermistor Failure, 0510 Fuser Failure, and 0520 Fuser Failure 0502 Thermistor Failure The temperature detected by the thermistor does not reach an expected level after the warm-up cycle starts. |
| Causes: | • Fuser, PL4.0.13 • Engine Control Board, PL13.0.20 • Power Supply, PL13.0.17 |
| Remedy: | 1 Check that the Fuser is installed correctly. Does the problem persist? Go to step 2. Complete. 2 Check the Engine Control Board connectors P/J2, P/J3, and P/J6. Are the connectors seated properly? Go to step 3 Reseat the connectors. If the problem persists, go to step 3. 3 Check the Low Voltage Power Supply connectors CN3, CN5, and CN7. Are the connectors seated properly? Go to step 4. Reseat the connectors. If the problem persists, go to step 4. 4 Replace the Fuser (8-9). Does the problem persist? Go to step 5. Complete. 5 Replace the Engine Control Board. Does the problem persist? Go to step 6. Complete. 6 Replace the Power Supply. Complete. |
| Error code: | 0503 |
| Display: | TERMISTOR2 |
| Description: | Thermistor resistance failure |
| Causes: | • The difference between the temperature detected by thermistor/1 and that detected by thermistor/2 exceeds a predetermined value. |
| Remedy: | 1 Change fuser unit. - - 2 For C110: 1. Main switch is turned ON. 2. Open the top cover. 3. Press the following keys in this order. ROTATE TONER key -ATTENTION key - ATTENTION key - ROTATE TONER key. 4. Main switch is turned OFF/ON. For C130n: 1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. See P.103 - - 3 Change PRCB. - - 4 Change DCPU. - - |
| Error code: | 0504 |
| Display: | Print Unable 05 Turn the power off and then back on again. |
| Description: | After the center thermistor of the fuser unit was normally heated, it detected a temperature lower than the specified value. |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure |
| Remedy: | < User Check > - Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset. 1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the harness of the center thermistor or side thermistor of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 4 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 0505 |
| Display: | Print Unable 05 Turn the power off and then back on again. |
| Description: | The center thermistor of the fuser unit detected a temperature rise greater than the specified value within a set period of time. |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure |
| Remedy: | < User Check > - Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset. 1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the harness of the center thermistor or side thermistor of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 4 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 0506 |
| Display: | Print Unable 05 Turn the power off and then back on again. |
| Description: | The center thermistor of the fuser unit detected a temperature fall greater than the specified value within a set period of time. |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure |
| Remedy: | < User Check > - Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset. 1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the harness of the center thermistor or side thermistor of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 4 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 0508 |
| Display: | Print Unable 05 Turn the power off and then back on again. |
| Description: | The side thermistor of the fuser unit did not detect a temperature rise when the heater was ON. |
| Remedy: | 1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 050A |
| Display: | Print Unable 05 Turn the power off and then back on again. |
| Description: | The center thermistor or side thermistor of the fuser unit detected some temperature error in the hardware. |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure |
| Remedy: | < User Check > - Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset. 1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the harness of the center thermistor or side thermistor of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 4 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 050B |
| Display: | Print Unable 05 Turn the power off and then back on again. |
| Description: | When the temperature of the center thermistor of the fuser unit is lower than the idle temperature, the side thermistor of the fuser unit detected a temperature higher than the specified value. |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure |
| Remedy: | < User Check > - Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset. 1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the harness of the center thermistor or side thermistor of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 4 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 050C |
| Display: | Print Unable 05 Turn the power off and then back on again. |
| Description: | When the temperature of the center thermistor of the fuser unit is higher than the idle temperature, the side thermistor of the fuser unit detected a temperature lower than the specified value. |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure |
| Remedy: | < User Check > - Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset. 1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the harness of the center thermistor or side thermistor of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 4 Connection failure of the low-voltage power supply PCB harness Reconnect the low-voltage power supply PCB harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 0900 |
| Display: | Print Unable 09 Turn the power off and then back on again. |
| Description: | FAX software incompatible detection error Incompatible FAX control PWB is installed. |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | Defective FAX software. Install the fax software. Defective FAX control PWB. Replace the fax control PWB and check for correct operation. |
| Error code: | 0A02 |
| Display: | Print Unable 0A Turn the power off and then back on again. |
| Description: | The fuser fan failure was detected. |
| Causes: | 1 Harness connection failure of the main fan 2 Harness connection failure of the high-voltage power supply PCB 3 Harness connection failure between the low-voltage power supply PCB and main PCB 4 Main fan failure 5 Low-voltage power supply PCB failure 6 High-voltage power supply PCB failure 7 Main PCB failure |
| Remedy: | 1 Connection failure of the fuser fan harness Reconnect the fuser fan harness. 2 Connection failure of the high-voltage power supply PCB harness Reconnect the high-voltage power supply PCB harness. 3 Fuser fan failure Replace the fuser fan. 4 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 0B01 |
| Display: | Print Unable 0B Turn the power off and then back on again. |
| Description: | Error occurred in the high-voltage power supply PCB ASSY while the machine is in operation. |
| Causes: | 1 Harness connection failure of the high-voltage power supply PCB 2 High-voltage power supply PCB failure 3 Main PCB failure |
| Remedy: | < User Check > - Replace the drum unit. 1 Connection failure of the high-voltage power supply PCB harness Reconnect the high-voltage power supply PCB harness. 2 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 0B02 |
| Display: | Print Unable 0B Turn the power off and then back on again. |
| Description: | Error occurred in the high-voltage power supply PCB ASSY in the ready state. |
| Causes: | 1 Harness connection failure of the high-voltage power supply PCB 2 High-voltage power supply PCB failure 3 Main PCB failure |
| Remedy: | < User Check > - Replace the drum unit. 1 Connection failure of the high-voltage power supply PCB harness Reconnect the high-voltage power supply PCB harness. 2 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 2200 |
| Description: | Main motor steady-state error After main motor is stabilized, the ready signal is at the H level for 2 s continuously. |
| Causes: | Main motor. Engine PWB. |
| Remedy: | Main motor 1. To check the motor operation execute U030 Main (main motor). 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Main motor and Engine PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the main motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2400 |
| Description: | Eject motor error After the motor drive ON signal is output and 1 s elapses, the rated speed reach signal is not input continuously for 2 s. |
| Causes: | Poor contact in the connector terminals. Defective drive transmission system. Defective engine PWB. Defective eject motor. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC27 on the engine PWB and the connector on the eject motor, and the continuity across the connector terminals. Repair or replace if necessary. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective engine PWB. Run maintenance item U030 and check if YC27-B4 (remote signal) on the engine PWB goes low. If not, replace the engine PWB. Defective eject motor. Run maintenance item U030 and check if the eject motor operates when YC27-B4 (remote signal) on the engine PWB goes low. If not, replace the eject motor. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2E00 |
| Display: | Load Roll Media |
| Description: | Paper mismatch (roll paper) No roll paper have been fed when a job with a roll paper specification is received. |
| Remedy: | Load roll paper. |
| Error code: | 3A00 |
| Display: | Print Unable 3A Turn the power off and then back on again. |
| Description: | Error occurred in the communication between the controller in the main PCB and engine. |
| Causes: | 1 Main PCB failure |
| Remedy: | 1 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 4000 |
| Display: | Supplies Drum End Soon. |
| Description: | Command Communication Error. |
| Causes: | The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error. |
| Remedy: | Replace the Main Board. |
| Error code: | 4200 |
| Display: | Supplies Replace Drum |
| Description: | BD steady-state error The BD signal is not detected. |
| Causes: | APC PWB (LSU). Main/Engine PWB. |
| Remedy: | APC PWB (LSU) 1. Confirm that the FCC wiring connector is not distorted and connect the FCC wiring all the way in. Laser scanner unit and main/engine PWB (YC2010) 2. If the FCC wiring is disconnected, shorted or grounded, replace the FCC wiring. 3. Replace the laser scanner unit. Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. |
| Error code: | 4B01 |
| Display: | Supplies Toner Low:BK |
| Description: | Dot counter of the toner cartridge (Black) or develop roller counter reaches the upper limit soon. |
| Causes: | 1 Main PCB failure if the error code remains after replacing with a new toner cartridge and resetting the toner counter |
| Remedy: | < User Check > - Prepare a new toner cartridge. 1 New toner actuator coming off Re-assemble the new toner actuator. 2 Connection failure of the new toner sensor PCB harness Reconnect the toner/new sensor PCB harness. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 4B06 |
| Description: | The amount of toner supplied of the toner box reaches the upper limit soon. |
| Remedy: | <User Check> • Prepare a new toner cartridge. 1 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 4C01 |
| Display: | Replace Toner Open the Top Cover, replace Toner Cartridge. Black (BK). |
| Description: | Dot counter of the toner cartridge (Black) or develop roller counter has reached the upper limit was detected. |
| Causes: | 1 Process drive unit damaged 2 Main PCB failure if the error code remains after replacing with a new toner cartridge and resetting the toner counter |
| Remedy: | < User Check > - Replace the toner cartridge whose counter reached the upper limit. 1 Main PCB failure if the error code remains after replacing with a new toner cartridge and resetting the toner counter Replace the main PCB ASSY. |
| Error code: | 4C06 |
| Description: | The amount of toner supplied of the toner box has reached the upper limit. |
| Remedy: | <User Check> • Replace the toner cartridge whose counter reached the upper limit. 1 Replace the toner cartridge or toner box with a new one and reset the toner counter. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY. |
| Error code: | 4D01 |
| Display: | Replace Toner |
| Description: | Dot count or develop roller counter of the toner cartridge in models without toner box is reaching the upper limit in the continuous printing mode. |
| Remedy: | <User Check> • Replace the toner cartridge whose counter reached the upper limit. 1 Replace the toner cartridge or toner box with a new one and reset the toner counter. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY. |
| Error code: | 4E01 |
| Display: | Toner Ended Open the Front Cover, replace Toner Cartridge. |
| Description: | Toner cartridge in models without toner box has reached the upper limit in the continuous printing mode. |
| Remedy: | <User Check> • Replace the toner cartridge whose counter reached the upper limit. 1 Replace the toner cartridge or toner box with a new one and reset the toner counter. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY. |
| Error code: | 4F01 |
| Display: | Cartridge Error Put the Toner Cartridge back in. |
| Description: | The new toner sensor of the toner cartridge (Black) could not detect a new cartridge properly. |
| Causes: | 1 Main PCB failure if the error code remains after replacing with a new toner cartridge and resetting the toner manual |
| Remedy: | < User Check > - Replace the toner cartridge with a new toner cartridge again. - If the place where the machine is installed is not flat, relocate the machine to a flat place. 1 Connection failure of the new toner sensor PCB harness Reconnect the toner/new sensor PCB harness. 2 New toner actuator that has come off or that has been caught Re-assemble the new toner actuator. 3 New toner sensor failure Replace the toner/new sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 4F05 |
| Description: | New process sensor could not detect the new drum unit correctly. |
| Remedy: | <User Check> • Replace the drum unit with a new drum unit again. • If the machine is on the uneven surface, place it on a level surface. 1 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 5E00 |
| Description: | New toner box sensor could not detect the new toner box correctly. |
| Remedy: | <User Check> • Replace the toner box with a new toner box again. • If the machine is on the uneven surface, place it on a level surface. 1 New toner box sensor failure Replace the high-voltage power supply PCB ASSY. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6001 |
| Display: | Cover is Open Close the Front Cover. |
| Description: | The front cover sensor detected that the front cover was open. |
| Causes: | 1 High-voltage power supply PCB harness connection failure 2 Top cover sensor failure 3 Main PCB failure |
| Remedy: | < User Check > - Close the front cover. 1 Connection failure of the front cover sensor harness Reconnect the front cover sensor harness. 2 Front cover failure Replace the front cover. 3 Front cover sensor failure Replace the front cover sensor. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6004 |
| Display: | Cover is Open Close the Back Cover of the machine. |
| Description: | Engine board error When a communication error in the Engine Board (PWB-A) is detected |
| Causes: | • Engine Board (PWB-A) |
| Remedy: | 1 Replace the PWB-A. |
| Error code: | 6101 |
| Display: | No Toner Open the Front Cover, then install Toner Cartridge. Black (BK). |
| Description: | Wrapping Jam |
| Causes: | Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21 |
| Remedy: | Pickup Cassette of the host machine |
| Error code: | 6106 |
| Description: | The new toner box sensor detected that no toner box was set. |
| Remedy: | <User Check> • Set the toner box correctly. 1 New toner box actuator coming off or caught in some sections of the machine Reattach the new toner box actuator. 2 New toner box sensor failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6200 |
| Display: | No Drum Unit Install the Drum Unit. |
| Description: | Broken fuser edge heater wire Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser center thermistor 1 1. Replace the Fuser unit. |
| Error code: | 6801 |
| Display: | Cooling Down Wait for a while |
| Description: | The internal temperature sensor or side thermistor of the fuser unit detected a temperature higher than the specified value. |
| Causes: | 1 Internal temperature sensor harness connection failure 2 Eject sensor PCB harness connection failure 3 Eject sensor PCB failure 4 Main PCB failure |
| Remedy: | < User Check > - Decrease the room temperature. - Place the machine away from a heater. 1 Connection failure of the internal temperature sensor harness Reconnect the internal temperature sensor harness. 2 Side thermistor of the fuser unit failure Replace the fuser unit. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6901 |
| Display: | Self-Diagnostic Turn the power off, then on again. Leave the machine for 15 min. |
| Description: | Some fuser unit errors occurred at power-ON or upon recovery from sleep mode. |
| Causes: | 1 Each harness connection failure of the fuser unit 2 Eject sensor PCB harness connection failure 3 Fuser unit failure 4 Eject sensor PCB failure 5 Low-voltage power supply PCB failure 6 Main PCB failure |
| Remedy: | 1 Connection failure of each harness of the fuser unit Reconnect each harness of the fuser unit. 2 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 3 Fuser unit failure Replace the fuser unit. 4 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 5 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY. Note: - Turn OFF the power switch. After checking that the fuser unit has cooled sufficiently, turn ON the power switch again and leave the machine for ten minutes. This problem may then be cleared. - To clear the fuser unit error after the remedy of the error is taken, enter the maintenance mode and then exit from the maintenance mode using Function code 99. |
| Error code: | 6902 |
| Display: | Self-Diagnostic Will Automatically Restart within 15 minutes. |
| Description: | After the errors was detected at the fuser unit, power was turned ON again and the error is being checked. (If power is turned OFF and ON after error code 6901 occurred, this code is displayed for about 15 minutes.) |
| Causes: | 1 Each harness connection failure of the fuser unit 2 Eject sensor PCB harness connection failure 3 Fuser unit failure 4 Eject sensor PCB failure 5 Low-voltage power supply PCB failure 6 Main PCB failure |
| Remedy: | 1 Connection failure of each harness of the fuser unit Reconnect each harness of the fuser unit. 2 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 3 Fuser unit failure Replace the fuser unit. 4 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 5 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY. Note: - Turn OFF the power switch. After checking that the fuser unit has cooled sufficiently, turn ON the power switch again and leave the machine for ten minutes. This problem may then be cleared. - To clear the fuser unit error after the remedy of the error is taken, enter the maintenance mode and then exit from the maintenance mode using Function code 99. |
| Error code: | 6A00 |
| Display: | Drum ! Slide the Blue tab on Drum Unit. |
| Description: | Electric discharge that may be caused by dirt on the corona wire of the drum unit was detected. |
| Causes: | 1 Dirt on the GRID terminals of the main body 2 Dirt on the terminal of the high-voltage power supply PCB 3 High-voltage power supply PCB failure 4 Main PCB failure |
| Remedy: | < User Check > - Clean the corona wire by sliding the blue tab of the drum unit for all four colors several times. - Clean the terminal of the drum unit. - Replace the drum unit. 1 Dirt on the GRID terminals of the main body Clean the GRID terminals of the main body. 2 Dirt on the terminal of the high-voltage power supply PCB Clean the terminal of the high-voltage power supply PCB. 3 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 6F00 |
| Display: | Print Unable ZC Turn the power off and then back on again. |
| Description: | Machine detected that supplied power was unstable. (Less than 100 times) |
| Causes: | 1 Connection failure of the center or side thermistor harness of the fuser unit. 2 Connection failure of the heater harness of the fuser unit. 3 Connection failure of the eject sensor PCB harness. 4 Connection failure of the lowvoltage power supply PCB harness. 5 Eject sensor PCB failure. 6 Fuser unit failure. 7 Low-voltage power supply PCB failure. 8 Main PCB failure. |
| Remedy: | < User Check > - Turn the power switch OFF/ON. - Insert the filter into the power supply. 1 The power supply waveform is incorrect Install a voltage stabilizer in the power supply part. |
| Error code: | 7000 |
| Display: | Jam Inside Open the Front Cover, pull out all four drum and toner cartridge assemblies and remove the jammed paper. |
| Description: | Toner motor problem The rated speed achievement signal won’t turn to L in 5 s since the motor is activated. The rated speed achievement signal turns to H every other 5 s after the machine is stabilized. |
| Causes: | Poor contact in the connector terminals. Broken the gear. Defective toner motor M/C/Y/BK. Defective engine PWB. |
| Remedy: | Poor contact in the connector terminals. Check the connection of connector YC30 on the engine PWB and the connector on the toner motor, and the continuity across the connector terminals. Repair or replace if necessary. Broken the gear. Check visually and replace the gear if necessary. Defective toner motor M/C/Y/BK. Run maintenance item U135 and check if the toner motor operates. If not, replace the toner motor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 7100 |
| Display: | Jam Rear Open the Back Cover and remove the jammed paper, then press [Start]. |
| Description: | Toner sensor error Sensor output value of 8 or less. |
| Causes: | Toner sensor. Toner motor. Main/Engine PWB. |
| Remedy: | Toner sensor 1. Check the toner sensor output by U150. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and main/engine PWB (YC9) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and main/engine PWB (YC12) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Main/Engine PWB 1. Check the main/engine software and upgrade to the latest, if necessary. 2. Replace the main/engine PWB. |
| Error code: | 7200 |
| Display: | Jam MP Tray Remove the jammed paper from MP Tray and press [Retry]. |
| Description: | Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7302 |
| Description: | Toner hopper motor C error During the Toner hopper motor C is driven, an event in which a locking was detected for 15 times in 200 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor Defective toner hopper sensor C. Defective toner hopper motor C. Defective engine PWB. |
| Remedy: | Toner hopper motor C 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner hopper motor C and retainer PWB (YC4) Retainer PWB (YC3) and front PWB (YC6) Front PWB (YC3) and engine PWB (YC7) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Toner motor C. Screw sensor C 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor C and Engine PWB (YC27) 3. Replace the screw sensor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8903 |
| Display: | 2-sided Disabled Close the Back Cover of the Machine. |
| Description: | The back cover sensor detected the open state when 2-sided printing is started. (before the registration of printing in the engine) |
| Causes: | 1 Back cover sensor harness connection failure 2 Back cover sensor installation failure 3 Breakage of boss that presses the back cover sensor 4 Back cover sensor failure 5 Main PCB failure |
| Remedy: | < User Check > - Close the back cover. 1 Connection failure of the back cover sensor harness Reconnect the back cover sensor harness. 2 Back cover sensor installation failure Re-assemble the back cover sensor. 3 Breakage of boss that presses the back cover sensor Replace the back cover. 4 Back cover sensor failure Replace the back cover sensor ASSY. 5 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8904 |
| Display: | 2-sided Disabled Close the Back Cover of the Machine. |
| Description: | The back cover sensor detected the open state during 2-sided printing. (after the registration of printing in the engine) |
| Causes: | 1 Back cover sensor harness connection failure 2 Back cover sensor installation failure 3 Breakage of boss that presses the back cover sensor 4 Back cover sensor failure 5 Main PCB failure |
| Remedy: | < User Check > - Close the back cover. 1 Connection failure of the back cover sensor harness Reconnect the back cover sensor harness. 2 Back cover sensor installation failure Re-assemble the back cover sensor. 3 Breakage of boss that presses the back cover sensor Replace the back cover. 4 Back cover sensor failure Replace the back cover sensor ASSY. 5 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8A01 |
| Display: | Size Error 2-sided Specify the correct paper. |
| Description: | The registration rear sensor detected that the fed paper was larger or smaller than the specified size in 2-sided printing. |
| Causes: | 1 Registration rear actuator catching on some position 2 Registration rear sensor failure 3 Main PCB failure |
| Remedy: | < User Check > - Use the Letter to Legal size paper. 1 Registration rear actuator caught on some position Re-assemble the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8C00 |
| Display: | Manual Feed Load paper. |
| Description: | There is no paper set in the manual feed slot on the manual feed slot printing. |
| Causes: | 1 Registration front/rear/manual feed sensor PCB harness connection failure 2 Manual feed actuator catching on some position 3 Manual feed sensor failure 4 Main PCB failure |
| Remedy: | <User Check> • Set the paper in the manual feed slot. 1 Registration front actuator caught in some sections of the machine Reattach the registration front actuator. 2 Connection failure of the registration front/rear sensor PCB harness Reconnect the registration front/rear sensor PCB harness. 3 Registration front sensor failure Replace the actuator holder ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8E01 |
| Display: | Size mismatch Fax received. Set correct paper size in menu. |
| Description: | Paper size is not set as A4/Letter/Legal/Folio when receiving fax or printing a list/report. |
| Causes: | 1 Main PCB failure |
| Remedy: | <User Check> • Set A4 or Letter-size paper. 1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the actuator holder ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 8E02 |
| Display: | Size Mismatch Reload correct paper. |
| Description: | Upon fax reception, the paper size setting is the one other than A4, Letter, Legal, and Folio. |
| Causes: | 1 Registration rear actuator catching on some position 2 Registration rear sensor failure 3 Main PCB failure |
| Remedy: | < User Check > - Set the paper size of the driver to A4, Letter, Legal, or Folio. 1 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9001 |
| Display: | Size mismatch Reload correct paper in MP Tray, then press [Retry]. |
| Description: | The size of paper loaded in the MP tray and the one specified from the driver are not same when paper is fed from the MP tray. |
| Remedy: | < User Check > - When specifying the paper in the driver, set the paper size of the paper that is actually set. 1 Registration rear actuator caught on some position Re-assemble the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9002 |
| Display: | Size mismatch Reload correct paper in Tray1,then press [Retry]. |
| Description: | The size of paper loaded in the paper tray 1 and the one specified from the driver are not same when paper is fed from the paper tray 1. |
| Causes: | 1 Registration rear actuator catching on some position 2 Registration rear sensor failure 3 Main PCB failure |
| Remedy: | < User Check > - When specifying the paper in the driver, set the paper size of the paper that is actually set. 1 Registration rear actuator caught on some position Re-assemble the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9201 |
| Description: | When printing from the MP tray, paper type setting in the machine does not match the setting in the driver. |
| Remedy: | • Use the same paper type setting for the machine and driver. 1 Malfunction of the main PCB Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9202 |
| Description: | When printing from the paper tray 1, paper type setting in the machine does not match the setting in the driver. |
| Remedy: | • Use the same paper type setting for the machine and driver. 1 Malfunction of the main PCB Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9301 |
| Display: | No Paper Reload paper in MP Tray. |
| Description: | When paper was fed from the MP tray, the MP paper empty sensor detected that no paper was in the MP tray. |
| Remedy: | < User Check > - Load paper to the MP tray. 1 MP paper empty actuator caught on some position Re-assemble the MP paper empty actuator. 2 Connection failure of the MP paper empty/registration front sensor PCB harness Reconnect the MP paper empty/ registration front sensor PCB harness. 3 MP paper empty sensor failure Replace the MP paper empty/registration front sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9302 |
| Display: | No Paper Reload paper in Tray 1. |
| Description: | When paper was fed from the paper tray 1, the T1 paper feed sensor detected that no paper was in the paper tray 1. |
| Causes: | 1 Foreign object in pick-up roller 2 Paper feed sensor PCB harness connection failure 3 Paper feed actuator catching on some position 4 Paper feed sensor failure 5 Gear failure inside of process drive unit 6 Main PCB failure |
| Remedy: | < User Check > - Load paper to the paper tray. 1 T1 paper feed actuator caught on some position Re-assemble the T1 paper feed actuator. 2 Connection failure of the T1 paper feed sensor PCB harness Reconnect the T1 paper feed sensor PCB harness. 3 T1 paper feed sensor failure Replace the T1 paper feed sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9309 |
| Description: | Detected that there was no paper set in all trays when TrayAuto was selected for printing. |
| Remedy: | • Set paper in the paper tray. 1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 Connection failure of an LT/TT paper empty sensor harness Reconnect the appropriate LT/TT paper empty sensor harness. 3 Connection failure of the T1 paper feed sensor harness Reconnect the T1 paper feed sensor harness. (Models with 250-sheet only) 4 An LT/TT paper empty actuator caught in some sections of the machine Reattach the appropriate LT/TT paper empty actuator. 5 T1 paper feed actuator caught in some sections of the machine Reattach the T1 paper feed actuator. (Models with 250-sheet only) 6 Abrasion of a PF kit Replace the appropriate PF kit. 7 An LT/TT paper empty sensor PCB failure Replace the appropriate LT/TT paper empty sensor PCB ASSY. 8 T1 paper feed sensor PCB failure Replace the T1 paper feed sensor PCB ASSY. (Models with 250-sheet only) 9 T1, T2, or T3(LT or TT) pickup clutch failure Replace the T1, T2, or T3(LT or TT) pickup clutch. 10 Paper feed motor failure Replace the paper feed motor. (Models with 250-sheet only) 11 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 12 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 13 TT relay PCB failure Replace a TT relay PCB ASSY. 14 TT control PCB failure Replace the TT control PCB ASSY. 15 Damaged gears in the paper feeding system Replace the main frame L ASSY. (Models with 250-sheet only) 16 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9701 |
| Display: | Size Error 2-sided Press [OK]. Specify the correct paper and load the same size paper as the Printer driver setting. |
| Description: | For 2-sided printing, the tray whose paper size was not supported by 2-sided printing was selected. |
| Causes: | 1 Main PCB failure |
| Remedy: | < User Check > - The size of the paper specified from the driver shall be A4 or Letter size and load the same size of paper to the specified paper tray. 1 Main PCB failure Replace the main PCB ASSY. |
| Error code: | 9702 |
| Display: | Size Error Specify the correct paper size for Tray 1. |
| Description: | For printing by feeding paper from the paper tray 1, the size of paper specified from the driver set the size which was not supported by the paper tray 1. |
| Remedy: | < User Check > - The size of the paper specified from the driver shall be A4 or Letter size and load the same size of paper to the specified paper tray. 1 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A000 |
| Display: | Scan Unable Remove the original document. Turn the power off, then on again. |
| Description: | Upon scanning the second side in duplex scanning, scanned data cannot be output with the required number of pixels and image processing is not completed successfully. |
| Causes: | 1 Second side CIS unit calibration data error 2 Second side CIS unit failure 3 Main PCB failure |
| Remedy: | 1 Second side CIS unit calibration data error Perform “Function code 55”. 2 Second side CIS unit failure Replace the second side CIS unit. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A200 |
| Display: | Document Jam Clear the scanner jam, then press the Stop Key. |
| Description: | During document scanning, the first side document scanning position sensor detected that the document length was 90 cm or more. |
| Causes: | 1 First side document scanning position actuator catching on some position 2 First side document scanning position sensor failure 3 Main PCB failure |
| Remedy: | < User Check > - Use documents equal to or smaller than A4 size. - Remove the jammed paper. 1 First side document scanning position actuator catching on some position Re-assemble the first side document scanning position actuator. 2 First side document scanning position sensor failure Replace the first side document scanning position sensor PCB. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A300 |
| Display: | Document Jam Clear the scanner jam, then press the Stop Key. |
| Description: | Though a document was fed and conveyed by the specified distance or longer, the first side document scanning position sensor did not detect the passing of the paper. |
| Causes: | 1 Coming off of first side document scanning position actuator. 2 First side document scanning position sensor failure 3 Main PCB failure |
| Remedy: | < User Check > - Match the document guide with the document size. - Remove the jammed paper. 1 First side document scanning position actuator catching on some position Re-assemble the first side document scanning position actuator. 2 Connection failure of the first side document scanning position sensor PCB harness Reconnect the first side document scanning position sensor PCB harness. 3 First side document scanning position sensor failure Replace the first side document scanning position sensor PCB. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A400 |
| Display: | Cover is Open Close the ADF Cover. / Close the ADF Cover, then press Stop[X]. |
| Description: | The ADF cover sensor detected that the ADF cover was opened. |
| Causes: | 1 Coming off of ADF cover actuator. 2 ADF cover/document detection sensor PCB harness connection failure 3 ADF cover sensor failure 4 Main PCB failure |
| Remedy: | < User Check > - Firmly close the ADF cover. 1 ADF cover actuator caught on some position Re-assemble the ADF cover actuator. 2 ADF cover/document detection sensor PCB installation failure Re-assemble the ADF cover/document detection sensor PCB ASSY. 3 Connection failure of the ADF cover/document detection sensor PCB harness Reconnect the ADF cover/document detection sensor PCB harness. 4 ADF cover damaged Replace the ADF cover. 5 ADF cover sensor failure Replace the ADF cover/document detection sensor PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A500 |
| Display: | Scan Unable Remove the original document. Turn the power off, then on again. |
| Description: | Upon scanning a fax, the first side CIS white or black calibration data was not within the normal range. |
| Causes: | 1 First side/second side CIS unit calibration data error 2 First side CIS unit failure 3 Second side CIS unit failure 4 Main PCB failure |
| Remedy: | 1 First side CIS unit calibration data error Perform “Function code 55”. 2 First side CIS flat cable damaged Replace the first side CIS flat cable. 3 First side CIS unit failure Replace the first side CIS unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A600 |
| Display: | Scan Unable A6 Turn the power off and then back on again. |
| Description: | Though a fax was scanned again after A500 error, the first side CIS white or black calibration data was not within the normal range. |
| Causes: | 1 First side/second side CIS unit calibration data error 2 First side CIS unit failure 3 Second side CIS unit failure 4 Main PCB failure |
| Remedy: | 1 First side CIS unit calibration data error Perform “Function code 55”. 2 First side CIS flat cable damaged Replace the first side CIS flat cable. 3 First side CIS unit failure Replace the first side CIS unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A700 |
| Display: | Print Unable A7 Turn the power off and then back on again. |
| Description: | The ROM color parameter does not match the first side CIS or second side CIS. |
| Causes: | 1 First side/second side CIS unit calibration data error 2 First side CIS unit failure 3 Second side CIS unit failure 4 Main PCB failure |
| Remedy: | 1 First side or second side CIS unit calibration data error Perform “Function code 55”. 2 First side CIS flat cable damaged Replace the first side CIS flat cable. 3 Second side CIS flat cable damaged Replace the second side CIS flat cable. 4 First side CIS unit failure Replace the first side CIS unit. 5 Second side CIS unit failure Replace the second side CIS unit. 6 Main PCB failure Replace the main PCB ASSY. |
| Error code: | A900 |
| Display: | Scan Unable A9 |
| Description: | When an image was scanned and processed, a scanning error occurred. |
| Causes: | 1 First side/second side CIS unit calibration data error 2 First side CIS unit failure 3 Second side CIS unit failure 4 Main PCB failure |
| Remedy: | 1 First side or second side CIS unit calibration data error Perform “Function code 55”. 2 First side CIS flat cable damaged Replace the first side CIS flat cable. 3 Second side CIS flat cable damaged Replace the second side CIS flat cable. 4 First side CIS unit failure Replace the first side CIS unit. 5 Second side CIS unit failure Replace the second side CIS unit. 6 Main PCB failure Replace the main PCB ASSY. |
| Error code: | AC00 |
| Display: | Scan Unable Remove the original document. Turn the power off, then on again. |
| Description: | Upon scanning a fax, the second side white or black calibration data was not within the normal range. |
| Causes: | 1 Second side CIS unit calibration data error 2 Second side CIS unit failure 3 Main PCB failure |
| Remedy: | 1 Second side CIS unit calibration data error Perform “Function code 55”. 2 Second side CIS flat cable damaged Replace the second side CIS flat cable. 3 Second side CIS unit failure Replace the second side CIS unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | AD00 |
| Display: | Scan Unable Remove the original document. Turn the power off, then on again. |
| Description: | First side scanned data cannot be output with the required number of pixels, and image processing cannot be completed successfully. |
| Causes: | 1 First side CIS unit calibration data error 2 First side CIS unit failure 3 Main PCB failure |
| Remedy: | 1 First side CIS unit calibration data error Perform “Function code 55” 2 First side CIS flat cable damaged Replace the first side CIS flat cable. 3 First side CIS unit failure Replace the first side CIS unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | AF00 |
| Display: | Scan Unable AF Turn the power off and then back on again. |
| Description: | The first side CIS fails to move, remaining at the home position. |
| Causes: | 1 Dust adhered to CIS rail 2 Coming off of CIS drive belt 3 Document scanner motor harness connection failure 4 First side CIS unit failure 5 Document scanner motor failure 6 Main PCB failure |
| Remedy: | 1 Dust adhered to guide shaft Remove the dust from the guide shaft. 2 Coming off of CIS drive belt Re-assemble the CIS drive belt. 3 Wiring failure of first side CIS flat cable Re-assemble the first side CIS flat cable. 4 Connection failure of the document scanner motor harness Reconnect the document scanner motor harness. 5 First side CIS flat cable damaged Replace the first side CIS flat cable. 6 First side CIS unit failure Replace the first side CIS unit. 7 Document scanner motor failure Replace the document scanner unit. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | B000 |
| Display: | SCANNER ERROR FB / SCANNER ERROR ADF |
| Description: | The first or second side CIS flat cable was detected to be not inserted correctly. |
| Causes: | 1 First side CIS harness connection failure 2 Second side CIS harness connection failure 3 First side CIS unit failure 4 Second side CIS unit failure 5 Main PCB failure |
| Remedy: | 1 Connection failure of the first side CIS flat cable Reconnect the first side CIS flat cable. 2 Connection failure of the second side CIS flat cable Reconnect the second side CIS flat cable. 3 First side CIS flat cable damaged Replace the first side CIS flat cable. 4 Second side CIS flat cable damaged Replace the second side CIS flat cable. 5 First side CIS unit failure Replace the first side CIS unit. 6 Second side CIS unit failure Replace the second side CIS unit. 7 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BB00 |
| Display: | Scanner Error BB |
| Description: | The white level value obtained with function code 55 was outside the specified range. |
| Causes: | 1 First side CIS unit failure 2 Second side CIS unit failure 3 Main PCB failure |
| Remedy: | 1 First side or second side CIS unit calibration data error Perform “Function code 55”. 2 First side CIS flat cable damaged Replace the first side CIS flat cable. 3 Second side CIS flat cable damaged Replace the second side CIS flat cable. 4 First side CIS unit failure Replace the first side CIS unit. 5 Second side CIS unit failure Replace the second side CIS unit. 6 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BC00 |
| Display: | Scan Unable BC Turn the power off and then back on again. |
| Description: | Though a fax was scanned again after AC00 error, the second side white or black calibration data was not within the normal range. |
| Causes: | 1 Second side CIS unit calibration data error 2 Second side CIS unit failure 3 Main PCB failure |
| Remedy: | 1 Second side CIS unit calibration data error Perform “Function code 55”. 2 Second side CIS flat cable damaged Replace the second side CIS flat cable. 3 Second side CIS unit failure Replace the second side CIS unit. 4 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BD00 |
| Display: | Scanner Error BD |
| Description: | The black level value obtained with function code 55 was outside the specified range. |
| Causes: | 1 First side CIS unit failure 2 Second side CIS unit failure 3 Main PCB failure |
| Remedy: | 1 First side or second side CIS unit calibration data error Perform “Function code 55”. 2 First side CIS flat cable damaged Replace the first side CIS flat cable. 3 Second side CIS flat cable damaged Replace the second side CIS flat cable. 4 First side CIS unit failure Replace the first side CIS unit. 5 Second side CIS unit failure Replace the second side CIS unit. 6 Main PCB failure Replace the main PCB ASSY. |
| Error code: | BF00 |
| Display: | Scan Unable Document is too longfor 2-sided scanning. Press Stop key. |
| Description: | The first side document scanning position sensor detected that the document was 400 mm or more in length and could not be fed from the ADF in duplex feeding. |
| Causes: | 1 First side document scanning position actuator catching on some position 2 First side document scanning position sensor failure 3 Main PCB failure |
| Remedy: | < User Check > - Use A4 or Letter size document. - Remove the jammed paper. 1 First side document scanning position actuator catching on some position Re-assemble the first side document scanning position actuator. 2 First side document scanning position sensor failure Replace the first side document scanning position sensor PCB. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | C700 |
| Display: | Out of Memory Press Stop Key |
| Description: | The memory is insufficient to expand the data of PC-Print. |
| Causes: | Main PCB failure |
| Remedy: | < User Check > - Print the print data stored in the memory. - Divide the print data and print it. 1 Main PCB failure Replace the main PCB ASSY. |
| Error code: | C800 |
| Display: | Print Data Full Print Data is full. Press Stop[X] Key and delete the previously stored data. |
| Description: | The memory used to store secure print data exceeded the memory size for secure print data. |
| Causes: | Main PCB failure |
| Remedy: | < User Check > - Print the print data stored in the memory. - Divide the print data and print it. 1 Main PCB failure Replace the main PCB ASSY. |
| Error code: | D100 |
| Display: | Print Unable D1 Turn the power off and then back on again. |
| Description: | An error occurred during modem initialization. |
| Causes: | 1 Modem PCB failure 2 Main PCB failure |
| Remedy: | 1 Connection failure of the modem PCB flat cable Reconnect the modem PCB flat cable. 2 Modem PCB failure Replace the modem PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | D200 |
| Display: | Machine Error |
| Description: | The machine detected that the modem PCB was disconnected. |
| Causes: | 1 Modem PCB harness connection failure 2 Modem PCB failure 3 Main PCB failure |
| Remedy: | 1 Connection failure of the modem PCB flat cable Reconnect the modem PCB flat cable. 2 Modem PCB failure Replace the modem PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY. |
| Error code: | D800 |
| Display: | Touchscreen initialization failed Remove any material which is on the touchscreen. |
| Description: | Error occurred during touch panel initialization. |
| Causes: | 1 Touch panel ASSY harness connection failure 2 Touch panel ASSY failure 3 Main PCB failure |
| Remedy: | 1 The version of the panel firmware and the main firmware do not match Install the latest panel firmware and main firmware. 2 Connection failure of the panel PCB harness Reconnect the panel PCB harness. 3 Connection failure of the touch panel flat cable Reconnect the touch panel flat cable. 4 Connection failure of the Key PCB flat cable Reconnect the key PCB flat cable. 5 Panel PCB failure Replace the panel PCB unit. 6 Touch panel ASSY failure Replace the touch panel ASSY. 7 Key PCB failure Replace the panel cover ASSY. 8 Main PCB failure Replace the main PCB ASSY. |
| Error code: | E000 |
| Display: | E000 |
| Description: | Fuser Temperature Rising Error |
| Causes: | The temperature of Fuser does not rise up to 50C. |
| Remedy: | Error clearance 1 Have you cleared the fuser error in the Error Clear Mode? Yes Wait until the Fuser Unit is enough cooled down. Then select the Error Clear Mode and clear the concerning error. Wires 2 Are wires among Lamp (H1), Solid State Relay (SSR1) and Thermistors (TH1 & TH2) connected properly? No Connect them properly. Lamp (H1) 3 Unplug the machine, and then check the resistance of Lamp (H1) with the multimeter. Is it 15 ohm or lower? No Replace the Lamp. Thermistors (TH1 & TH2) 4 Select the Information Mode, and then check the temperature of fuser detected by Thermistors (TH1 & TH2). Item No. : 00 (Fuser temperature 1) 01 (Fuser temperature 2) Is each temperature normal? No Replace the concerning Thermistor. Confirm that the machine is turned on, and then check the voltage of the orange line (J220-4). Is it 24V? No Replace the DC Power Supply if there is no problem with the wires. DC Power Supply (DCP1) or Fuse 5 Confirm that the machine is turned off, and then check whether or not each Fuse is broken. Is any Fuse broken? Yes Replace the Fuse. Relay (RY1) 6 Select the Device Operation Mode, and then change the signal of the following signal to “H”. Signal Code : 22 (Fuser Relay) And check the resistance between the following points. Between RY1-2 and RY1-4 Between RY1-6 and RY1-8 Is the each resistance almost 0 ohm? No Replace the Relay. Solid State Relay (SSR1) 7 Select the Device Operation Mode, and then change the signal of the following signals to “H”. Signal Code : 22 (Fuser Relay) 21 (Fuser Lamp 1) Then check the voltage between J105-1 and J105-2. Is it 0V? Refer to the page 8-16 as for the Device Operation Mode.) CAUTION Change the signal of “21” (Fuser Lamp 1) to “L” after checking! No Replace the PW10520 PWB. Yes Replace the Solid State Relay |
| Error code: | E100 |
| Display: | E100 error Vacuum pump |
| Description: | Abnormal condition in vacuum pump. |
| Causes: | • PH Unit • PH Interface Board (PWB-D) • Mechanical Control Board (PWB-M) |
| Remedy: | (1) MAIN board assembly may be damaged. * Replace MAIN board assembly. |
| Error code: | E500 |
| Display: | Print Unable E5 Turn the power off and then back on again. |
| Description: | MAIN MOTOR failure MOTOR ASSY is not turning, or not turning normally. |
| Causes: | • Main Motor (M1) • Mechanical Control Board (PWB-M) • DC Power Supply (PU1) |
| Remedy: | 1. Connectors on LVPS and MCU Board Assy are correctly connected? 2. Check the connections between MAIN MOTOR <=> LVPS <=> MCU Board Assy. Disconnection/slant connection of a connector Disconnection/damage of a harness. 3. MAIN MOTOR is not turning normally due to an abnormal load on it. Check GEAR ASSY HOUSING`s Drive Transmission Path. 4. Replace MAIN MOTOR. 5. Replace LVPS. 6. Replace MCU Board Assy. |
| Error code: | E600 |
| Display: | Print Unable E6 Turn the power off and then back on again. |
| Description: | Cyan TCR Sensor adjustment failure - TCR Sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. |
| Causes: | • Photoconductor Unit /C • Photoconductor Unit /M • Photoconductor Unit /Y • Toner Supply Motor Y/M (M6) • Toner Supply Motor C/K (M7) • Mechanical Control Board (PWB-M) • Controller Board (PWB-P) |
| Remedy: | 1 Clean the TCR Sensor window on the underside of the Photoconductor Unit if dirty - - 2 M6, M7 operation check PWB-M CNDM2-10 to 13 (M6) PWB-M CNDM3-10 to 13 (M7) C-22 C-23 3 Reinstall Photoconductor Unit - - 4 Change Photoconductor Unit - - 5 Change PWB-M - - 6 Change PWB-P |
| Error code: | E701 |
| Display: | Print Unable E7 Turn the power off and then back on again. |
| Description: | MP tray Rise Descent Error - The Bypass Lift-Up Sensor is not blocked even when the Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the standby position to the feed position was started. - The Bypass Lift-Up Sensor is not unblocked even when the Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the feed position to the standby position was started. |
| Causes: | • MP tray Lift-up Sensor (PC14) • Vertical Transport Motor (M2-PC) • Control Board (PWB-Z-PC) |
| Remedy: | 1 Check the M2-PC connector for proper connection and correct as necessary. - - 2 Check the connector of M2-PC for proper drive coupling and correct as necessary. - - 3 PC14 I/O check, Sensor check PWB-M CNTRY1-10 (ON) C-10 4 M2-PC operation check PWB-Z PJ5Z PC-5~8 Q-22 5 Change PWB-Z-PC. |
| Error code: | E702 |
| Display: | Print Unable E7 Turn the power off and then back on again. |
| Description: | Standard cassette Elevator failure - The Lift-Up Sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started. |
| Causes: | • Lift-up Sensor (PC7-PC) • Lift-up Sensor (PC7-PC) • Control Board (PWB-Z-PC) |
| Remedy: | 1 Check the M3-PC connector for proper connection and correct as necessary. - - 2 Check the connector of M3-PC for proper drive coupling and correct as necessary. - - 3 PC7-PC I/O check, Sensor check PWB-Z PJ6Z PC-3 (ON) PWB-Z PJ4Z PC-4 to 5 V-21 to 22 4 M3-PC operation check Q-24 5 Change PWB-Z-PC. |
| Error code: | E900 |
| Display: | Print Unable E9 Turn the power off and then back on again. |
| Description: | Copy counter |
| Causes: | Mechanical Control Board (PWB-M) |
| Remedy: | 1. Any other electric appliances; generators, radiotransmitter, etc., within three meters from the printer? In such a case, noises from them may cause an error in reading/writing; therefore, change the location of them or turn them off. 2. MCU Board Assy itself has abnormality. Replace MCU Board Assy. |
| Error code: | F900 |
| Description: | Model information error |
| Remedy: | Setting Recover the machine information by means of the following procedure. Notes: The following procedure is supported in the firmware with the version “2050” or later. If the version is before “2050”, first upgrade it to “2050” or later with [4] + [9] → [1] for “SYSTEM FIRMWARE (OS Data)”. <Machine information recovery> 1. Turn the power ON while pressing [6] and the [CLEAR] button simultaneously. 2. Key in [3] to select “3. SRAM Re-Initialize Support”, and then press the [START] button. 3. After the operation is completed, shut down the equipment by pressing the [ON/OFF] button. * If it is not recovered, perform the following procedure. 4. Turn the power ON while pressing [3] and the [CLEAR] button simultaneously. 5. Enter the password on the Authentication screen. If no password is set for Service, press the [OK] button without entering anything. If the High Security Mode has been set, enter “#1048#”. 6. Key in [5] to select “5. Key Backup Restore”, and then press the [START] button. 7. Key in [2] to select “2. Key FROM to SRAM”, and then press the [START] button. 8. After the operation is completed, shut down the equipment by pressing the [ON/OFF] button. |
